Din 7992-2010
Din 7992-2010
DISTRIBUZIONE CONTROLLATA
NORME TECNICHE Rev. 00
(UNI, EN, ISO, CEI, ASME, SAE, etc..)
(ISO 9001:2015 - sez. 7.5)
Pag. 1 di 1
DIN 7992-2010 1 of 1
September 2010
DIN 7992
DIN
CS 21.06010 Supersedes
DIN 7992:1970-12
Translation by DIN-Sprachendienst.
In case of doubt, the German-language original shall be considered authoritative.
Contents
Page
Foreword 3
I Scope 3
2 Normative references 3
3 Dimensions 4
4 Technical delivery conditions 6
5 Designation 6
Annex A (informative) Example of application 7
Bibliography 8
03
2
DIN 7992:2010-09
Foreword
This standard has been prepared by Working Committee NA 067-00-08 AA Verbindungselemente mit Sonder
formen und aus Kunststoff of the Normenausschuss Mechanische Verbindungselemente (Fasteners Standards
Committee).
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. DIN shall not be held responsible for identifying any or all such patent rights.
Amendments
This standard differs from DIN 7992:1970-12 as follows:
a) a scope has been defined;
b) normative references have been updated;
c) the loading capacity has been deleted in Table 1;
d) the technical delivery conditions (Clause 4) have been completely revised;
e) the example of application and the specifications for the bolt pocket are now given in an informative
Annex A.
Previous editions
DIN 7992: 1957-11, 1961-03, 1970-12
I Scope
This standard specifies properties for sizes M24 to M100x6 T-head bolts with large head.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
DIN 76-1, Thread run-outs and thread undercuts — Part 1: For ISO metric threads in accordance with
DIN 13-1
DIN 962, Bolts, screws, studs and nuts — Designation, types and finishes
DIN EN 26157-1, Fasteners — Surface discontinuities — Part 1: Bolts, screws and studs subject to general
requirements
DIN EN ISO 898-1, Mechanical properties of fasteners made of carbon steel and alloy steel — Part 1: Bolts,
screws and studs with specified property classes Coarse thread and fine pitch thread
—
DIN EN ISO 4753, Fasteners — Ends of parts vith external metric ISO thread
3
DIN 7992:2010-09
DIN EN ISO 4759-1, Tolerances for fasteners — Part 1: Bolts, screws, studs and nuts — Product grades A, B
and C
DIN ISO 724, ISO general purpose metric screw threads — Basic dimensions
DIN ISO 965-1, ISO general purpose metric screw threads — Tolerances — Part 1: Principles and basic data
DIN ISO 8992, Fasteners — General requirements for bolts, screws, studs and nuts
3 Dimensions
See Figure 1 and Table 1.
Key
1 notch in longitudinal direction of T-head
a
length I is to be stated at the time of ordering (see also Annex A)
b
thread run-out as in DIN 76-1
Thread end chamfered (CH) or rounded (RN) as in DIN EN ISO 4753 at the manufacturers discretion.
4
DIN 7992:2010-09
Table I — Dimensions
Dimensions in millimetres
d1 M24 M30 M36 M42 M48 M56 M64 M72 x 6 M80 x 6 M90 x 6 MIOO x 6
b 100 120 140 170 200 220 240 260 290 320 350
Ii 18 20 25 30 30 30 30 30 30 30 30
k 18 22 25 30 35 40 50 55 60 70 75
o 24 30 36 42 48 56 64 72 80 90 100
q 65 75 85 95 110 125 140 155 170 185 205
r,,, 1,6 1,6 2 2 2 3 3 4 4 4 5
Mass of head
(dimensionk)
0,205 0,360 0,555 0,850 1,34 2,00 3,21 4,40 5,80 8,30 11,0
kg/unit
Mass per
20 mm
bolt length 0,071 0,111 0,160 0,218 0,284 0,386 0,506 0,640 0,790 0,998 1,23
kg/unit
5
DIN 7992:2010-09
Material Steel
Tolerance class 8g
Thread
Standard DIN ISO 965-1, DIN ISO 724
As processed.
DIN EN 26157-1 applies with regard to limits for surface
. discontinuities DIN EN ISO 4042 applies with regard to
Surface finish
electroplating, DIN EN ISO 10683 applies with regard to zinc
flake coatings, DIN EN ISO 10684 applies with regard to hot dip
galvanizing.
Acceptance inspection DIN EN ISO 3269 applies with regard to acceptance inspection.
5 Designation
EXAMPLE Designation of an M36 T-head bolt with large head, of nominal length I (nominal size) = 1 200 mm and
property class 5.6:
See DIN 962 for supplementary order designations for special bolt types and finishes.
6
DIN 7992:2010-09
Annex A
(informative)
Example of application
a
Length / is given by the depth of insertion f plus projection a. This length is to be stated at the time of
ordering and shall be rounded in each case to the nearest 20 mm. If intermediate lengths are unavoidable,
these shall be graded in 10 mm increments.
Figure A.1 — Bolt pocket
Dimensions in millimetres
Bolt pocket M24 M30 M36 M42 M48 M56 M64 M72 x 6 M80 x 6 M90 x 6 MIQO x 6
L 140 150 170 190 210 220 240 260 280 300 320
e 30 35 42 50 58 65 75 85 95 105 115
f 800 1 000 1 200 1 400 1 600 1 800 2 000 2 200 2 400 2 600 2 800
Channel
section 65 65 80 100 120 120 140 140 160 160 180
DIN_1026-1
7
DIN 7992:2010-09
Bibliography
DIN 1026-1, Hot rolled steel channels — Part 1: Taper flange steel channels — Dimensions, masses and
sectional properties