DOUBLE OFFSET BUTTERFLY VALVES

Body design WAFER type with through holes

LUG type with threaded holes

Nominal size DN50 - DN600

Working pressure 16 bar / 25 bar / 40 bar / 50 bar

Flange connection PN6 / PN10 / PN16 / PN25 / PN40

Class 150 / Class 300

Working temperature -55°C / +325°C *)

Working media Waste / Supply water

Potable water
Hot industrial water
Crude oil
Petroleum products
Fuel / Oil / Oil derivatives
Pulp / Paper stock
Natural gas
Coke oven gas
Stack gas
Steam / Condensate
Air
Bitumen (asphalt)

Tightness Class A **)

Features Excentric seat design

Bi directional tightness
(RS design)
SIL2 / SIL3 ***)
certification
ATEX performance ***)
TA-Luft stuffing box ***)
*) higher working temperatures
upon request according
to the material performance
of the valve body
**) Metal-Metal seat tightness
Class C
***) upon request

SERIES 2E energy line www.abovalve.com

GENERAL VALVE
DESCRIPTION Industrial Valve Manufacturer

Type designation
5 5 9 0 B 100
The 2E-series double offset butterfly Nominal size (DN)
valves are industrial fittings intended Body design
for full opening or closing flow. They may B - AFER W body type with th holes readed
be also used for a rough flow control. The T - LUG body type with tapped holes
valves are designed for operation with Disc material
very hard industrial conditions demanding 0 - stainless steel 1.4408 (CF8M)
safety, reliability and minimum maintnance stainless steel 1.4409 (ASTM A351 CF3M)
like for example: stainless steel 1.4027 (ASTM CA-40)
Seat material
• nuclear energy industry 9 - R-PTFE (PTFE reinforced by 25% glass fibre)
• water treatment 8 - FIRE SAFE (R-PTFE + INCONEL)
• gas pipe-works 7 - INCONEL 718 2.4668
• chemical industry Body material
• metallurgy 6 - low carbon steel 1.1156 (A352 LCC)
(and heavy industry in general) 5 - carbon steel 1.0625 (A216 WCB)
• pulp and paper-making industry 4 - stainless steel 1.4408 (A351 CF8M))
• shipbuilding industry Series designation
• oil and petrochemical industry Series 2E
• heat recovery, steam heating
• processing hydrocarbons
• fuel storage in aviation industry

Basic properties
• double offset design
• eccentric disc position in the body, pre-
cise connection of the disc with the
stem and pivot, exact shaft and pivot
bearing in the slide bushings
• split sealed stem - bigger Kv Standards
• high efficiency of opening and closing
valve Leak test Design „R-PTFE”
• easy operation Design „ Fire Safe”
• easy assembly and installation EN 12266-1, Class A
• vacuum max. 0,01 bar abs. ISO 5208, Class A
(version R-PTFE) API 598
• standardized top flange according to
EN ISO 5211 enabling mount various Design „Metal-Metal”
types of actuator (electric, pneumatic, DN 50-DN125
hydraulic) EN 12266-1, Class C
• ATEX certified for explosive atmosphere ISO 5208, Class C
• option: TA-Luft sealed valve - stem is API 598
sealed with a special graphite gland
Face to face lenght EN 558, Series 20
ISO 5752, Series 20
API 609, Table 3

ATEX performance according to 2014/34/EU

Flange connection EN 1092-1, 2
Top flange EN ISO 5211
Working standard EN 593
Marking EN19

2 / ABO Valve Czech

 VALVE MODELS

B T B T
WAFER LUG WAFER LUG
DESIGN DESIGN DESIGN DESIGN

Standard line
DN50-DN400
Bi-directional
line (RS design)
DN50-DN600

DN50-DN125 DN150-DN600

Advantages of double offset valves Quality control

• split stem allows higher Kv/Cv values • ABO valve production facilities are
• lower pressure loss certified in accordance with ISO Split stem/
• gas pipe-works 9001:2015 (14001, 45001) quality Better
• guaranteed tightness in both directions control standards flow rate
at nominal working pressure (RS version) • tightness test procedures according to
• sealing ring and seat come to contact standards EN 12266-1, ISO 5208,
only nearly after the valve is entirely shut ANSI/FCI 70-2, API598
• low closing torque • production in accordance with the
• the seal guarantees perfect upper stem Pressure Equipment Directive
tightness 2014/68/EU (Module H)
• water and air tightness • the possibility of issuing inspection
• actuator connection can be done by certificate 3.1, 3.2
bracket or the stem can be extended if • all the actuators are adjusted and tested
connected to special actuator types while assembled
• all the certificates can be downloaded
at www.abovalve.com

The stem seal

One piece design ABO design
with TA-LUFT
certification
for perfect tightness
of pollutants
into the ambient air
(upon request)
www.abovalve.com /3
DESIGN
ADVANTAGES Industrial Valve Manufacturer

Double offset
• the double offset design provides a safe function and tightness even after a sudden tempe
rature or pressure change. It reduces seat wear and ensures perfect tightness. The first
offset (1) shifts the axis of the rotation off the sealing surface and thus provides tightness
between the seat and the sealing ring around the entire disc circumference. The second
offset (2) moves the the axis of the disc rotation off the valve (pipeline) axis and thus relea-
ses the ring from the seat after a few degrees of opening movement. The reason of the
second offset is to quickly relieve the seal from compression between the disc and the seat
• the design extends the seal lifetime and the torques are lower. When shutting valve, the r
tating movement is changed to the linear one and the disc is effec tively pressed into the
seal. The design also prevents undesirable agglomerating e. g. undissolved substances in
the area of disc and seal contact.

(1) - stem axis

is off the sealing surface
(2) - stem offset
off the pipeline axis

Stem and seal (3)

• two-piece stem - thanks to the split stem the valve attains higher
values of Kv/Cv and related low pressure loss
• adjusting seal according to the customers‘ requirements - the
seal can be tightened to the parameters prescribed by customers
Thus maximum tightness can be achieved around the stem and
the actuation torque for low-pressure applications can be decreased.
• adjustable seal - enables easy access to final adjustment of the seal
without dismantling the actuator
• stem assembly - upper and lower bushings made from TP Igus
provides high abrasion resistance and prolongs valve lifespan

• extended neck - enables to insulate

piping incl. the valve
• easy service and seal replacement -
easy assembly and replacement
• top flange according to ISO 5211 -
enables to directly install a manual
handle or an actuator

Seal design
• R-PTFE - suitable seal geometry ensures full tightness and a high number of cycles. The PTFE
seal is reinforced with 25% glass fibres, reducing wear and and increasing valve thermal
stability. Longer lifespan of the valve and lower maintenance demand are guaranteed.
• end-stops - are designed to avoid overruning the maximum allowable position of the disc.
Thus the seal is not damaged nor overloaded and the valve lifespan is extended (4) (5).

4 / ABO Valve Czech

MATERIAL
PERFORMANCE

32
15

METAL- METAL
Seat details
3
29
8
2

31 15 8 28 30 31
30

FIRE SAFE
PTFE
28 3
8 29
8
2
2

Item Name Material

Item Name Material

1 Body 6 - low carbon steel 1.1156 (A352 LCC)

14 Washer Stainless steel A4
5 - carbon steel 1.0625 (A216 WCB)
4 - stainless steel 1.4408 (A351 CF8M) 15 Flange Graphite min. 98%
2 Disc DN50-125: stainless steel 1.4409 (ASTM A351 CF3M) sealing
DN150-600: 16 Cover Graphite
55xx: stainless steel 1.4027 (ASTM CA-40) seal
54xx, 56xx: stainless steel 1.4408 (ASTM A351 CF8M
17 Bracket DN50-125, 500, 600: carbon stell 1.0553
3 Pressure Carbon steel 1.0425 DN150-400: carbon stell 1.0576
flange Stainless steel 1.4404 (AISI 316L)
18 Bolt Stainless steel A4
4 Stem 54XX, 56XX: stainless steel 1.4462
55XX: stainless steel 1.4021 (AISI 420) 19 Retaining Stainless steel 1.4404 (AISI 316L)
sleeve
5 Pivot DN50-125: stainless steel 1.4404 (AISI 316L)
DN150-600: stainless steel 1.4021 (AISI 420)/1.4462 20 Bolt Stainless steel A4

6 Cover DN50-125: - 21 Bushing Xx70, Xx80: stainless steel 1.4404

DN150-600: carbon steel 1.4025 / stainless steel 1.4401 (AISI 316L) + nickel plated
(AISI 316) XX90: TP IGUS

7 Pin DN50-125: - 22 Sealing Graphite min. 98%

54XX, 56XX DN150-600: stainless steel 1.4462
23 Washer Stainless steel A4
55XX DN150-600: stainless steel 1.4021 (AISI 420)
8 Seat XX70 DN50-125: INCONEL 718 2.4668 24 Nut Stainless steel A4
XX80: FIRE SAFE (R-PTFE + INCONEL)
XX90: R-PTFE (PTFE reinforced by 25% glass fiber) 25 Bolt Stainless steel A4

9 Washer Stainless steel 1.4404 (AISI 316L) 26 Rivet Stainless steel A4

10 Stuffing DN50-125: - 27 Label Stainless steel
box 54XX, 55XX DN150-600: stainless steel 1.4401 (AISI 316)
56XX DN150-300: stainless steel 1.4401 (AISI 316) 28 Seat Stainless steel 1.4404 (AISI 316L) - only for „R-PTFE”
56XX DN350-600: stainless steel 1.4404 (AISI 316L) O-ring and „FIRE SAFE” version
11 Sealing 54XX, 55XX, 56XX DN50-125: stainless steel 1.4308 (CF8) 29 Sealing INCONEL - only for „METAL-METAL” and „FIRE SAFE” version
flange 54XX, 55XX, 56XX DN150-600: stainless steel
1.4301 (AISI 304) 30 Support Stainless steel 1.4404 (AISI 316L)
ring
12 Bolt Stainless steel A4
31 Retaining Stainless steel 1.4401
13 Nut Stainless steel A4
ring
32 Support Stainless steel 1.4404 (AISI 316L)
Working pressure max. Temperature rating *) ring
R-PTFE seat - tightness A -29°C do 200°C (R-PTFE) - 5590
DN50-DN100: 50 bar 55°C do 325°C (Inconel) - 5470 Other material performance on request. To select a suitable material solution please contact ABO
valve company. Maximum temperatures for each seats are only permitted for specific media and
DN125-DN200: 40 bar
short-term use.
DN250-DN450: 25 bar Coating
Metal-Metal RAL 9005 - standard
seat - tightness C Coating resistant to high
Fire Safe seat - tightness A temperatures (up to +600°C)
DN50-DN125: 25 bar upon request
*) depending on the material performance
www.abovalve.com /5
of the valve body (will be specified - please consult with ABO)
OPERATING TORQUES
/ FLANGE CONNECTION Industrial Valve Manufacturer

Operating torques (Nm) vs. working pressure (bar)

R-PTFE seat (standard line DN50-DN400)
DN 50 65 80 100 125 150 200 250 300 350 400 450 500 600
NPS 2“ 2 1/2 „ 3“ 4“ 5“ 6“ 8“ 10“ 12“ 14“ 16“ 18“ 20“ 24“
PS 16 bar 19 35 50 77 110 145 278 567 650 1378 2248 2569 3090 4300
PS 25 bar 22 45 58 79 120 185 366 732 900 1900 3483 3925 5340 6250
PS 40 bar 32 53 62 90 150 242 485 -
PS 50 bar 25 60 65 105 -
Operating torques are mentioned without safety reserve.

Metal-metal seat and Fire Safe seat

DN 50 65 80 100 125
NPS 2“ 2 1/2 „ 3“ 4“ 5“
PMAX 16 bar 50 70 100 150 220
PMAX 16 bar 50 70 100 150 220
Operating torques are mentioned without safety reserve

Installation between flanges DN50 - DN600

DN 50 65 80 100 125 150 200 250 300 350 400 450 500 600
NPS 2“ 2 1/2 „ 3“ 4“ 5“ 6“ 8“ 10“ 12“ 14“ 16“ 18“ 20“ 24“
PN6 • • • • • • • • • • x x x
PN10
PN16
PN25
PN40 x x
ANSI150
ANSI300 x x x x x
JIS 10K • • • • x • •
JIS 16K • • • •
For Lug type (T) installation, please specify in the inquiry

Standard • Upon request x Impossible

KV (CV) coefficient
DN 50 65 80 100 125 150 200 250 300 350 400 450 500 600
NPS 2“ 2 1/2 „ 3“ 4“ 5“ 6“ 8“ 10“ 12“ 14“ 16“ 18“ 20“ 24“
KV 87 148 312 456 750 1125 1950 3100 4510 6120 8605 9419 11674 16914
CV 102 173 364 532 876 1313 2277 3619 5265 7145 10046 10926 13542 19620

6 / ABO Valve Czech

PRESSURE
AND TEMPERATURE CURVES

Body A351 CFM / PTFE seat Body A216 WCB / PTFE seat

2 5 2 5

°C °C

Body A216 WCB / Metal-Metal seat

°C

Body A351 CFM / Metal-Metal seat

°C

www.abovalve.com /7
VALVE ACTUATION
Industrial Valve Manufacturer

All the ABO valves can be equipped with hand levers (up to DN150), worm
gears, pneumatic and electric actuators. The upper flange design according
to the standard ISO 5211 enables to directly assemble actuators on valves.

Handlever
For manual actuation ABO valve
offers carbon steel lever suitably painted to DN 50-100 125 150*)
improve resistance to corrosion and abra-
A 270 270 362
sion. Stainless lever on request. Top flange
connection according to ISO standards F07 B 75 80 90
for DN50 to DN125 and F10 for DN150.
Controlled lever on request. The levers can Weight 1,26 1,26 1,40
be equipped with a padlock to ensure an op-
timized position, can be equipped with end
position sensors.

Worm gear with handwheel

Manual gearbox housing is made from cast iron with suitable surface treatment and protection degree class IP 67. Se-
lf-locking design of the worm gear enables both to adjust basic positions open/shut and to control (throttle) media flow.
The worm gearbox is simply actuated by means of a handwheel of a suitable diameter. End-limit positions of the worm
gearbox are set by means of stop screws. The gearbox can be equipped with a lockable system secured by a padlock.
Another way how to handle worm gearbox is using a chain. The worm gearbox as well as the hand lever can be completed
with end-limit position sensors

DN PS ISO SHAFT A B C D E F Kg
FLANGE
50 50 F07 14x14 127 46 139 59 141 200 2,9
65 50 F07 14x14 127 46 139 59 141 200 2,9
80 50 F07 14x14 127 46 139 59 141 200 2,9
100 50 F07 14x14 127 46 139 59 141 200 2,9
125 40 F07 14x14 127 46 139 59 141 200 2,9
150 40 F10 17x17 133 59 154 60 155 200 2,9
200 40 F10 17x17 133 59 154 62 155 200 2,9
250 25 F12 22x22 287 67 275 181 319 500 10
300 25 F14 27x27 287 67 275 181 319 500 10
350 25 F16 27x27 352 78 275 219 381 600 13
400 25 F16 36x36 398 110 346 245 454 700 24,6
450 25 F16 Ø55 408 142 400 120 480 700 50
500 25 F25 Ø64 255 142 378 142 330 400 40
600 25 F25 Ø75 363 175 429 175 440 500 50

Actuators
Pneumatic actuators
Pneumatic actuators ABO Series 95 can be assembled to valves
in two options: single-acting or double-acting.

Pneumatic actuators
Electric actuators ABO Series 97 are designed quarter-turn.
Electric actuators can be installed on ABO valves for voltages of
24 V, 230 V or 400 V.

Special actuators types

Valves are equipped with special actuator types from major world
suppliers (Auma, Regada, Valpes, etc.).

8 / ABO Valve Czech

BASIC DIMENSIONS

DN d1 d2 A B C D1 D2 s1 s2 E G ISO
FLANGE
y b DESIGN B
(kg)
DESIGN T
(kg)

50 49 68 163 93 44 104 154 12 37 25 14 F07 9 70 5,1 7,3

65 65 82 170 100 47 123 178 39 55 25 14 F07 9 70 5,8 9,0
80 81 100 174 106 47 140 196 65 72 25 14 F07 9 70 6,8 10,1
100 100 123 206 123 53 163 225 85 91 25 14 F07 9 70 8,5 12,2
125 123 146 215 137 57 193 260 113 110 25 14 F07 9 70 11,8 16,5

DN d1 d2 A B C D1 D2 s1 s2 E G ISO
FLANGE
y b DESIGN B
(kg)
DESIGN T
(kg)

150 146 155 307 214 57 252 318 136 143 25 17 F10 11 4 21 28
200 194 204 339 246 61 307 381 185 193 25 17 F10 11 4 29 41
250 240 259 395 275 69 349 450 224 236 31 22 F12 13 4 46 70
300 287 309 460 313 79 393 521 270 284 31 27 F14 17 4 67 105
350 313 342 508 355 92 448 577 300 308 45 27 F16 22 4 91 140
400 364 405 556 402 103 542 657 342 360 58 36 F16 22 4 132 211
450 420 450 567 395 114 565 - 400,2 419 80 ¯55/16 F16 22 4 165 -
/62,6

500 452 500 625 431 127 593 707 434 454 100 ¯64/18 F25 17,5 8 241 282
/72,4

600 547 600 698 491 154 695 830 524 546 110 ¯75/20 F25 17,5 8 367
/84,2

www.abovalve.com /9
 BIDIRECTIONAL TIGHTNESS / -RS-
VESION (DN50-DN600) Industrial Valve Manufacturer

B T
WAFER LUG
DESIGN DESIGN

Butterfly valves of 2E series (RS version) are delivered in

nominal sizes of DN50 to DN600. Their make provides
bidirectional tightness of the valve. On the circumferen-
ce the valve is sealed with a special RTFE seal filled with T
25% glass fibres and silicone filling. LUG
Body material DESIGN
• carbon steel 1.0625 (A216 WCB)
/ 1.0425 (P265 GH)
• low carbon steel 1.1156 (A352 LCC)
/ 1.0566 (P355 NL1)
• stainless steel 1.4409 (CF3M)
/ 1.4401 (AISI 316)
Disc material: B
WAFER
• DN50-DN125
DESIGN
stainless steel 1.4409 (ASTM A351 CF3M
• DN150-600:
55xx: stainless steel 1.4027 (ASTM CA-40)
54xx, 56xx: stainless steel 1.4408
(ASTM A351 CF8M)

Valve features
DN50-DN125 DN150-DN600
• bidirectional tight and control butterfly valve
with all-stainless disc
• double offset design
• sizes DN50 to DN600
• tightness class A (EN 12266-1)
• better flow rate due to split stem
• the seat is adapted to large temperature
changes
• delivered for manual, electric or pneumatic
control
• suitable for heat and power plants, steam and
hot water pipework systems
• the valves may be delivered with a special surface
protection

Czech Republic USA Russia China

ABO valve, s.r.o. ABO Controls LLC ABO Armatura LLC ABO Flow Control
Dalimilova 285/54 Houston Smolensk Shanghai
783 35 Olomouc tel.: +(1) 832.291.4929 tel.: +7 (4812) 240 020 tel.: +86 136 01 522 831
tel.: +420 585 224 087 sales.us@abovalve.com sales.ru@abovalve.com sales.cn@abovalve.com
sales@abovalve.com

Slovak Republic Ukraine India United Arab Emirates

ABO Slovakia, s.r.o. ABO Ukraine LLC ABO Controls Pvt. Ltd. Sales representation Follow us on:
Banská Bystrica Dnipro Mumbai Abu Dhabi
tel.: +421 947 902 862 tel.: +38 056 733 95 70 tel.: +91 773 820 4779 tel.: +971 56 9207964
sales.sk@abovalve.com sales.ua@abovalve.com sales.in@abovalve.com bharti@abovalve.com

Germany Turkey
ABO Armaturen GmbH ABO Armaturen LTD STI
Singapore
ABO Valve Pte. Ltd.
Bahrain
Sales representation
www.abovalve.com
Essen Istanbul Singapore Manama
tel.: +49 (0)152 262 29501 tel.: +90 216 527 36 34 tel.: +65 9169 4562 tel.: +973 3444 9065
sales.de@abovalve.com sales.tr@abovalve.com sales.sg@abovalve.com jimmichen@abovalve.com

The technical information described in this leaflet is teantive and for general use only and does not constitute a recommendation or guarantee
for any specific service or application requirement. Please consult ABO representative or factory for specific requirements and material
selection for your intended application. The right to change or modify product design or product without prior notice is reserved. ABO valve
accepts no liability for damages caused by bad interpretation or use of the information included in this brochure.
Valid from: 2/2023