TB85 & TB85-BTC UEFI BIOS Manual

UEFI BIOS Setup ........................................................................... 1

1 Main Menu................................................................................... 3
2 Advanced Menu .......................................................................... 4
3 Chipset Menu............................................................................ 19
4 Boot Menu................................................................................. 23
5 Security Menu ........................................................................... 25
6 Performance Menu ................................................................... 27
7 Exit Menu .................................................................................. 35

i
 TB85 & TB85-BTC UEFI BIOS Manual

UEFI BIOS Setup

Introduction
The purpose of this manual is to describe the settings in the AMI UEFI
BIOS Setup program on this motherboard. The Setup program allows
users to modify the basic system configuration and save these settings to
NVRAM.
UEFI BIOS determines what a computer can do without accessing
programs from a disk. This system controls most of the input and output
devices such as keyboard, mouse, serial ports and disk drives. BIOS
activates at the first stage of the booting process, loading and executing
the operating system. Some additional features, such as virus and
password protection or chipset fine-tuning options are also included in
UEFI BIOS.
The rest of this manual will to guide you through the options and settings in
UEFI BIOS Setup.
Plug and Play Support
This AMI UEFI BIOS supports the Plug and Play Version 1.0A
specification.
EPA Green PC Support
This AMI UEFI BIOS supports Version 1.03 of the EPA Green PC
specification.
ACPI Support
AMI ACPI UEFI BIOS support Version 1.0/2.0 of Advanced Configuration
and Power interface specification (ACPI). It provides ASL code for power
management and device configuration capabilities as defined in the ACPI
specification, developed by Microsoft, Intel and Toshiba.
PCI Bus Support
This AMI UEFI BIOS also supports Version 2.3 of the Intel PCI (Peripheral
Component Interconnect) local bus specification.
DRAM Support
DDR3 SDRAM (Double Data Rate III Synchronous DRAM) is supported.

1
 TB85 & TB85-BTC UEFI BIOS Manual

Using Setup
When starting up the computer, press <Del> during the Power-On
Self-Test (POST) to enter the UEFI BIOS setup utility.
In the UEFI BIOS setup utility, you will see General Help description at the
top right corner, and this is providing a brief description of the selected item.
Navigation Keys for that particular menu are at the bottom right corner,
and you can use these keys to select item and change the settings.

General Help

Navigation Keys

Notice
 The default UEFI BIOS settings apply for most conditions to ensure
optimum performance of the motherboard. If the system becomes
unstable after changing any settings, please load the default settings
to ensure system’s compatibility and stability. Use Load Setup Default
under the Exit Menu.
 For better system performance, the UEFI BIOS firmware is being
continuously updated. The UEFI BIOS information described in this
manual is for your reference only. The actual UEFI BIOS information
and settings on board may be slightly different from this manual.
 The content of this manual is subject to be changed without notice.
We will not be responsible for any mistakes found in this user’s
manual and any system damage that may be caused by
wrong-settings.

2
 TB85 & TB85-BTC UEFI BIOS Manual

1 Main Menu
Once you enter AMI UEFI BIOS Setup Utility, the Main Menu will appear on
the screen providing an overview of the basic system information.

BIOS Information
It shows system information including UEFI BIOS version, Project Code,
Model Name, Build Date and etc.
Total Memory
Shows system memory size, VGA shard memory will be excluded.
System Language
Choose the system default language.
System Date
Set the system date. Note that the ‘Day’ automatically changes when you
set the date.
System Time
Set the system internal clock.

3
 TB85 & TB85-BTC UEFI BIOS Manual

2 Advanced Menu
The Advanced Menu allows you to configure the settings of CPU, Super
I/O, Power Management, and other system devices.
Notice
Beware of that setting inappropriate values in items of this menu may
cause system to malfunction.

PCI Subsystem Settings

4
 TB85 & TB85-BTC UEFI BIOS Manual

PCI Latency Timer

This item sets the value to be programmed into PCI Latency Timer
Register.
Options: 32 PCI Bus Clocks (Default) / 64 PCI Bus Clocks / 96 PCI Bus
Clocks / 128 PCI Bus Clocks / 160 PCI Bus Clocks / 192 PCI Bus Clocks /
224 PCI Bus Clocks / 248 PCI Bus Clocks
No Snoop
This item enables or disables PCI Express Device No Snoop option.
Options: Enabled (Default) / Disabled
Maximum Payload
This item sets Maximum Payload of PCI Express Device or allows System
BIOS to select the value.
Options: Auto (Default) / 128 Bytes / 256 Bytes / 512 Bytes / 1024 Bytes
/ 2048 Bytes / 4096 Bytes
Maximum Read Request
This item sets Maximum Read Request Size of PCI Express Device or
allows System BIOS to select the value.
Options: Auto (Default) / 128 Bytes / 256 Bytes / 512 Bytes / 1024 Bytes
/ 2048 Bytes / 4096 Bytes

5
 TB85 & TB85-BTC UEFI BIOS Manual

ACPI Settings

Enable ACPI Auto Configuration

This item enables or disables BIOS ACPI Auto Configuration.
Options: Disabled (Default) / Enabled
Enable Hibernation
This item enables or disables system ability to hibernate (OS/S4 Sleep
State). This option may be not effective with some OSes.
Options: Enabled (Default) / Disabled
ACPI Sleep State
This item selects the highest ACPI sleep state the system will enter when
the SUSPEND button is pressed.
Options: S1 only (CPU Stop Clock) (Default) / Suspend Disabled / S3 only
(Suspend to RAM) / Both S1 and S3 available for OS to choose from
PME Wake up from S5
The item enables the system to wake from S5 using PME event.
Options: Disabled (Default) / Enabled
Wake system with Fixed Time
This item enables or disables the system to wake on by alarm event. When
this item is enabled, the system will wake on the hr::min::sec specified.
Options: Disabled (Default) / Enabled
Wake up date
You can choose which date the system will boot up.

6
 TB85 & TB85-BTC UEFI BIOS Manual

Wake up hour / Wake up minute / Wake up second

You can choose the system boot up time, input hour, minute and second to
specify.
PS2 Keyboard PowerOn
This item allows you to control the keyboard power on function.
Options: Disabled (Default) / Any Key / Stroke Key / Specific Key
Stroke Keys
This item will show only when Keyboard PowerOn is set “Stroke Key.”
Options: Wake Key (Default) / Power Key / Ctrl+F1 / Ctrl+F2 / Ctrl+F3 / Ctrl
+F4 / Ctrl+F5 / Ctrl+F6
Specific Key
This item will show only when Keyboard PowerOn is set “Specific Key.” Press
Enter to set Specific key.
PS2 Mouse PowerOn
This item allows you to control the mouse power on function.
Options: Disabled (Default) / Enabled
USB Device Wakeup from S3/S4
This item allows you to enable or disabled the USB resume from S3/S4
function.
Options: Disabled (Default) / Enabled
CPU Setting and Information
This item shows CPU Information

7
 TB85 & TB85-BTC UEFI BIOS Manual

Limit CPUID Maximum

When the computer is booted up, the operating system executes the
CPUID instruction to identify the processor and its capabilities. Before it
can do so, it must first query the processor to find out the highest input
value CPUID recognizes. This determines the kind of basic information
CPUID can provide the operating system.
Options: Disabled (Default) / Enabled
Execute-Disable Bit
XD can prevent certain classes of malicious buffer overflow attacks when
combined with a supporting OS (Windows Server 2003 SP1, Windows XP
SP2, SuSE Linux 9.2, RedHat Enterprise 3 Update 3.).
Options: Enabled (Default) / Disabled
Intel Virtualization Technology
When enabled, a VMM can utilize the additional hardware capabilities
provided by Vanderpool Technology
Options: Enabled (Default) / Disabled
Hardware Prefetcher
This item enables or disables the Mid Level Cache (L2) streamer
Prefetcher.
Options: Enabled (Default) / Disabled
Adjacent Cache Line Prefetch
This item enables or disables the Mid Level Cache (L2) prefetching of
adjacent cache lines.
Options: Enabled (Default) / Disabled

8
 TB85 & TB85-BTC UEFI BIOS Manual

SATA Configuration
The BIOS will automatically detect the presence of SATA devices. There is
a sub-menu for each SATA device. Select a device and press <Enter> to
enter the sub-menu for detailed options.

SATA Controller(s)
This item enables/disables Serial ATA Device.
Options: Enabled (Default) / Disabled
SATA Mode Selection
This item determines how SATA controller(s) operate.
Options: AHCI (Default) / IDE
SATA Self Test
This item runs SMART Self Test on all HDDs during POST.
Options: Disabled (Default) / Enabled
Hot Plug
This item enables/disables Hot Plug function.
Options: Enabled (Default) / Disabled
External SATA
This item enables/disables External SATA support.
Options: Disabled (Default) / Enabled

9
 TB85 & TB85-BTC UEFI BIOS Manual

Intel(R) Rapid Start Technology

Intel(R) Rapid Start Technology

This item enables/disables Intel(R) Rapid Start Technology.
Options: Disabled (Default) / Enabled

Note: The following items appear only when you set the iRST function to [Enabled]Entry on
S3 RTC Wake
This item sets iFFS invocation upon S3 RTC wake.
Options: Enabled (Default) / Disabled
Entry After
This item enables RTC wake timer at S3 entry. The value range is from
0(Immediately) to 120 minutes.
Active Page Threshold Support
This item allows system to support RST with small partition.
Options: Disabled (Default) / Enabled

Note: The following items appear only when you set the Active Page Threshold Support
function to [Enabled]
Active Memory Threshold
This item allows system to try to support RST when partition size >
Active Page Threshold size in MB. When set to zero, the item will be in
AUTO mode and check if partition size is enough at S3 entry.
Options: 0 (Default)
Hybrid Hard Disk Support
This item enables/disables Hybrid Hard Disk Support.
Options: Disabled (Default) / Enabled

10
 TB85 & TB85-BTC UEFI BIOS Manual

RapidStart Display Save/Restore

This item enables/disables RapidStart Display Save/Restore.
Options: Disabled (Default) / Enabled

Note: The following items appear only when you set the RapidStart Display
Save/Restore function to [Enabled]
RapidStart Display Type
This item selects RapidStart Display type.
Options: BIOS Save/Restore (Default) / Desktop Save/Restore
PCH-FW Configuration
It shows FCH-FW configuration.

USB Configuration

11
 TB85 & TB85-BTC UEFI BIOS Manual

Legacy USB Support

The item allows you to enable Legacy USB support. AUTO option disables
legacy support if no USB devices are connected. DISABLE option will keep
USB devices available only for EFI applications.
Options: Enabled (Default) / Disabled / Auto
USB3.0 Support
This item enables or disables USB3.0 (XHCI) Controller support.
Options: Enabled (Default) / Disabled
XHCI Hand-Off
This is a workaround for OSes without XHCI hand-off support. The XHCI
ownership change should be claimed by XHCI driver.
Options: Enabled (Default) / Disabled
XHCI Mode
The item selects Mode of operation of xHCI controller.
Options: Smart Auto (Default) / Auto / Enabled / Disabled / Manual

Note: The following items appear only when you set the XHCI Mode to [Manual]
XHCI Pre-Boot Driver
The item allows you to enable or disable XHCI Pre-Boot Driver support.
Options: Enabled (Default) / Disabled
EHCI Hand-Off
This is a workaround for OSes without EHCI hand-off support. The EHCI
ownership change should be claimed by EHCI driver.
Options: Disabled (Default) / Enabled
USB Mass Storage Driver Support
The item allows you to enable or disable USB Mass Storage Driver
Support.
Options: Enabled (Default) / Disabled
USB transfer time-out
The time-out value for Control, Bulk, and Interrupt transfers.
Options: 20 sec (Default) / 1 sec / 5 sec / 10 sec
Device reset time-out
The item sets USB mass storage device Start Unit command time-out.
Options: 20 sec (Default) / 10 sec / 30 sec / 40 sec

12
 TB85 & TB85-BTC UEFI BIOS Manual

Device power-up delay

“Auto” uses default value: for a Root port it is 100ms, for a Hub port the
delay is taken from Hub descriptor.
Options: Auto (Default) / Manual

Note: The following items appear only when you set the Device power-up delay function
to [Manual]
Device power-up delay in seconds
Delay range is 1 ~ 40 seconds, in one second increments.
Options: 5 (Default)
SMART FAN Control

CPU Smart FAN

This item allows you to control the CPU Smart Fan function.
Options: Disabled (Default) / Auto
CPU FAN Calibrate
Press [ENTER] to calibrate CPU FAN.
Control Mode
This item provides several operation modes of the fan.
Options: Quiet / Aggressive / Manual
Fan Ctrl OFF(℃)
When CPU temperature is lower than this value, the CPU fan will keep
lowest RPM.
Options: 10 (℃) (default)

13
 TB85 & TB85-BTC UEFI BIOS Manual

Fan Ctrl On(℃)

When CPU temperature is higher than this value, the CPU fan controller
will turn on.
Options: 20 (℃) (Default)
Fan Ctrl Start Value
This item sets CPU FAN Start Speed Value.
Options: 50 (Default)
Fan Ctrl Sensitive
The bigger the numeral is, the higher the FAN speed is.
Options: 30 (Default)
Super IO Configuration

Restore AC Power Loss

This setting specifies how your system should behave after a power fail or
interrupts occurs. Power Off: Leaving the system in power-off status after
power recovers. Power ON: Powering on the system immediately when
power returns. Last State: 1. Leaving the system in power-off if the system
shuts down at DC off status; 2. Powering on the system immediately if the
system shuts down at DC on status.
Options: Power Off (Default) / Power On / Last State

14
 TB85 & TB85-BTC UEFI BIOS Manual

Serial Port 0 Configuration

Serial Port
This item enables or disables Serial Port (COM).
Options: Enabled (Default) / Disabled
Change Settings
This item selects an optimal setting for Super IO device.
Options: Auto (Default) / IO=3F8h; IRQ=4 / IO=3F8h; IRQ=3, 4, 5, 6, 7,
9, 10, 11, 12 / IO=2F8h; IRQ=3, 4, 5, 6, 7, 9, 10, 11, 12 / IO=3E8h; IRQ=3,
4, 5, 6, 7, 9, 10, 11, 12 / IO=2E8h; IRQ=3, 4, 5, 6, 7, 9, 10, 11, 12
CIR Controller Configuration

CIR Controller
This item enables or disables CIR Controller.
Options: Disabled (Default) / Enabled

15
 TB85 & TB85-BTC UEFI BIOS Manual

Change Settings
This item selects an optimal setting for Super IO device.
Options: Auto (Default) / IO=3E0h; IRQ=10 / IO=3E0h;
IRQ=3,4,5,6,7,9,10,11,12 / IO=2E0h; IRQ=3,4,5,6,7,9,10,11,12 / IO=298h;
IRQ=3,4,5,6,7,9,10,11,12
H/W Monitor

PWM Processor Hot

This item enables or disables PWM Processor Hot.
Options: Enabled (Default) / Disabled
Shutdown Temperature
This item allows you to set up the CPU shutdown Temperature.
Options: Disabled (Default) / 70℃/158℉ / 75℃/167℉ / 80℃/176℉ /
85℃/185℉ / 90℃/194℉

16
 TB85 & TB85-BTC UEFI BIOS Manual

Intel (R) Smart Connect Technology

ISCT Support
This item enables/disables ISCT Support.
Options: Disabled (Default) / Enabled
Note: The following items appear only when you set the ISCT Support function to
[Enabled]
ISCT Notification Control
Options: Enabled (Default) / Disabled
ISCT WLAN Power Control
Options: Enabled (Default) / Disabled
ISCT WWAN Power Control
Options: Enabled (Default) / Disabled
ISCT RF Kill Switch Type
Options: Software (Default) /Hardware
ISCT Timer Selection
Options: EC Timer (Default) / RTC Timer

17
 TB85 & TB85-BTC UEFI BIOS Manual

Network Stack

Network Stack
This item enables or disables UEFI network stack
Options: Disabled (Default) / Enabled

Note: The following items appear only when you set the Network Stack function to
[Enabled]
IPv4 PXE Support
This item enables or disables IPv4 PXE Boot Support. If disabled IPv4 booth
option will not be created.
Options: Enabled (Default) / Disabled
IPv6 PXE Support
This item enables or disables IPv6 PXE Boot Support. If disabled IPv6 booth
option will not be created.
Options: Enabled (Default) / Disabled

18
 TB85 & TB85-BTC UEFI BIOS Manual

3 Chipset Menu
This section describes configuring the PCI bus system. PCI, or Personal
Computer Interconnect, is a system which allows I/O devices to operate at
speeds nearing the speed of the CPU itself uses when communicating with
its own special components.
Notice
Beware of that setting inappropriate values in items of this menu may
cause system to malfunction.

PCH-IO Configuration

19
 TB85 & TB85-BTC UEFI BIOS Manual

PEX1_1 / PEX1_2 / PEX1_3 / PEX1_4 / PEX1_5 / PEX1_6 / PEX1_7

Note: PEX1_6 & PEX1_7 are only for TB85-BTC.
ASPM
This item sets PCI Express Active State Power Management settings.
Options: Disabled (Default) / L0s / L1 / L0sL1 / Auto
PCIe Speed
This item selects PCI Express port speed.
Options: Auto (Default) / Gen1 / Gen2
Detect Non-Compliance Device
This item detects non-compliance PCI Express Device. If enable, it will
take more time at POST time.
Options: Disabled (Default) / Enabled
Onboard Lan
This item enables/disables the PCI Express Root.
Options: Enabled (Default) / Disabled
Onboard LAN Option ROM
This item enables/disables Onboard LAN Option ROM.
Options: Disabled (Default) / Enabled
Azalia
This item controls detection of the Azalia device. Disabled = Azalia will be
unconditionally disabled. Enabled = Azalia will be unconditionally Enabled.
Options: Auto (Default)/ Enabled / Disabled
EuP Control
When EuP is enabled, the system will meet EuP requirement.
Options: Disabled (Default) / Enabled in S5 / Enabled in S4-S5

20
 TB85 & TB85-BTC UEFI BIOS Manual

System Agent (SA) Configuration

Primary Display
This item selects which of IGFX/PEG/PCI Graphics device should be
Primary Display or select SG for Switchable Gfx.
Options: Auto (Default) / IGFX / PEG / PCIE
Primary PEG
This item selects AUTO/PEG11/PEG12 Graphics device should be
Primary PEG
Options: Auto (Default) / PEG11/ PEG12
Primary PCIE
This item selects AUTO / PCIE1 / PCIE2 / PCIE3 / PCIE4 / PCIE5 / PCIE6 /
PCIE7 Graphics device should be Primary PCIE
Options: Auto (Default) / PCIE1 / PCIE2 / PCIE3 / PCIE4 / PCIE5 /
PCIE6 / PCIE7
Internal Graphics
This item keeps IGD enabled based on the setup options.
Options: Auto (Default) / Disabled / Enabled
GTT Size
This item selects the GTT Size.
Options: 2MB (Default) / 1MB
Aperture Size
This item selects the Aperature Size.
Options: 256MB (Default) / 128MB / 512MB

21
 TB85 & TB85-BTC UEFI BIOS Manual

DVMT Pre-Allocated
This item selects DVMT 5.0 Pre-Allocated (Fixed) Graphics Memory size
used by the Internal Graphics Device.
Options: 32M (Default) / 64M / 96M / 128M / 160M / 192M / 224M /
256M / 288M / 320M / 352M / 384M / 416M / 448M / 480M / 512M / 1024M
DVMT Total Gfx Mem
This item selects DVMT5.0 Total Graphic Memory size used by the Internal
Graphics Device.
Options: 256MB (Default) / 128MB / MAX
PEX16_1 Slot
PCIE16_1 - Gen X
This item selects PCI Express port speed.
Options: Auto (Default) / Gen1 / Gen2 / Gen3
PCIE16_1 - ASPM
This item sets PCI Express Active State Power Management settings.
Options: Disabled (Default) / ASPM L0s / ASPM L1 / ASPM L0sL1 /
Auto
RC6 (Render Standby)
This item enables or disables render standby support.
Options: Enabled (Default) / Disabled

22
 TB85 & TB85-BTC UEFI BIOS Manual

4 Boot Menu
This menu allows you to setup the system boot options.

Setup Prompt Timeout

This item sets number of seconds to wait for setup activation key.
Options: 2 (Default)
Bootup NumLock State
This item selects the keyboard NumLock state.
Options: On (Default) / Off
Full Screen Logo Display
This item allows you to enable/disable Full Screen Logo Show function.
Options: Enabled (Default) / Disabled
Boot Success Beep
When this item is set to Enabled, BIOS will let user know boot success with
beep.
Options: Enabled (Default) / Disabled
BIOS Flash protection
While enabled, it can’t flash write and flash erase by SMI.
Options: Enabled (Default) / Disabled
GateA20 Active
Upon Request – FA20 can be disabled using BIOS services. Always – do
not allow disabling GA20; this option is useful when any RT code is
executed above 1MB
Options: Upon Request (Default) / Always

23
 TB85 & TB85-BTC UEFI BIOS Manual

Option ROM Messages

This item sets the display mode for option ROM.
Options: Force BIOS (Default) / Keep Current
INT19 Trap Response
BIOS reaction on INT19 trapping by Option ROM: IMMEDIATE – execute
the trap right away; POSTPONED – execute the trap during legacy boot.
Options: Postponed (Default) / Immediate
Launch CSM
This option controls if CSM will be launched
Options: Enabled (Default) / Disabled
Boot option filter
This option controls what devices system can boot to.
Options: UEFI and Legacy (Default) / Legacy only / UEFI only
Launch PXE OpROM policy
This option controls the execution of UEFI and Legacy PXE OpROM
Options: Legacy only (Default) / UEFI only / Do not launch
Launch Storage OpROM policy
This option controls the execution of UEFI and Legacy Storage OpROM
Options: Legacy only (Default) / UEFI only / Do not launch
Launch Video OpROM policy
This option controls the execution of UEFI and Legacy Video OpROM
Options: Legacy only (Default) / UEFI only / Do not launch
Other PCI device ROM priority
For PCI devices other than Network, Mass storage or video defines which
OpROM to launch.
Options: UEFI OpROM (Default) / Legacy OpROM
Boot Option Priorities
The items specify the boot device priority sequence from the available
devices. The number of device items that appears on the screen depends
on the number of devices installed in the system.

24
 TB85 & TB85-BTC UEFI BIOS Manual

5 Security Menu

Administrator Password
This item sets Administrator Password.
User Password
This item sets User Password.
Secure Boot Menu

Secure Boot Control

Secure Boot flow control. Secure Boot can be enabled only when 1.
Platform Key (PK) is enrolled and Platform is operating in user mode and
2.CSM function is disabled in Setup.
Options: Disabled (Default) / Enabled

25
 TB85 & TB85-BTC UEFI BIOS Manual

Note: The following items appear only when you set the Secure Boot Control function to
[Enabled]

Key Management

Install or Delete All Factory Default Keys

It allows you to immediately load/clear the default Security Boot keys,
Platform key (PK), Key-exchange Key (KEK), Signature database (db), and
Revoked Signatures (dbx). The Platform Key (PK) state will change from
Unloaded mode to Loaded mode. The settings are applied after reboot or
at the next reboot.
Platform Key (PK)
Delete PK – Allows you to delete the PK file from your system.
Set new PK – Allows you set new PK file.
Key Exchange Key Database (KEK)
Delete KEK – Allows you to delete the KEK file from your system.
Set new KEK – Allows you set new KEK file.
Append Var to KEK – Allows you append Var to KEK.
Authorized Signature Database (DB)
Delete DB – Allows you to delete the DB file from your system.
Set new DB – Allows you set new DB file.
Append Var to DB – Allows you append Var to DB.
Forbidden Signature Database (DBX)
Delete DBX – Allows you to delete the DBX file from your system.
Set new DBX – Allows you set new DBK file.
Append Var to DBX – Allows you append Var to DBX.

26
 TB85 & TB85-BTC UEFI BIOS Manual

6 Performance Menu
This submenu allows you to change voltage and clock of various devices.
(However, we suggest you use the default setting. Changing the voltage
and clock improperly may damage the device.)
Notice
 The options and default settings might be different by RAM or CPU
models.
 Beware of that setting inappropriate values in items of this menu may
cause system to malfunction.
- Values in Red: Danger
- Values in Yellow: Warning
- Values in White: Normal

Start Page
You can set the entrance page when you enter UEFI BIOS Setup.
Options: Page – Main (Default) / Page – Advanced / Page – Chipset /
Page – Boot / Page – Security / Page – Performance / Page – Save & Exit

27
 TB85 & TB85-BTC UEFI BIOS Manual

CPU Configuration

CPU Ratio Mode

This item sets CPU Ratio Mode.
Options: Auto (Default) / ALL Cores / Per Core / Fixed
CPU Core Current Max (AMP)
This item sets CPU Core Current Max.
Options: 256 (Default)
Enhanced Intel SpeedStep Technology
This item enables/disables Enhanced Intel SpeedStep Technology.
Options: Enabled (Default) / Disabled
Turbo Mode
This item enables/disables CPU Turbo Mode.
Options: Enabled (Default) / Disabled
Power Limit 1 Value (Watt)
This item sets the power limit 1 value (Watt).
Options: 125 (Default)
Power Limit 1 Time (Second)
This item sets the power limit 1 time (Second).
Options: 8 (Default)
Power Limit 2 Switch
This item sets the power limit Switch
Options: Enabled (Default) / Disabled

28
 TB85 & TB85-BTC UEFI BIOS Manual

Power Limit 2 Value (Watt)

This item sets the power limit 2 value (Watt).
Options: 150 (Default)
Active Processor Cores
Number of cores to enable in each processor package
Options: All (Default) / 1 / 2 / 3
CPU C states
This item enables or disables CPU C states.
Options: Enabled (Default) / Disabled
Enhanced C1 states
This item enables or disables Enhanced C1 states.
Options: Enabled (Default) / Disabled
CPU C3 Report
This item enables or disables CPU C3 report.
Options: Enabled (Default) / Disabled
CPU C6 Report
This item enables or disables CPU C6 report.
Options: Disabled (Default) / Enabled
CPU C7 Report
This item enables or disables CPU C7 report.
Options: Disabled (Default) / CPU C7 / CPU C7s
Graphics Core (GT) Frequency
This item sets Graphics Core (GT) Frequency.
RING Ratio
This item sets RING Ratio.

29
 TB85 & TB85-BTC UEFI BIOS Manual

Voltages Configuration

CPU Override Voltage Target (mV)

This item sets CPU Override Voltage Target, 0mV – 2000mV.
Offset Prefix
This item selects the offset value as positive (+) or negative (-).
Options: + (Default) / -
RING Override Voltage Target (mV)
This item sets RING Override Voltage Target, 0mV – 1850mV.
Offset Prefix
This item selects the offset value as positive (+) or negative (-).
Options: + (Default) / -
FIVR OVP/OCP Enable
This item enables or disables FIVR OVP/OCP function control.
Options: Enabled (Default) / Disabled
FIVR Efficiency Enable
FIVR Efficiency Enable. If this function be disabled, will not be change until
CPU powers down.
Options: Enabled (Default) / Disabled
GT Voltage Mode
This item sets GT Voltage Mode.
Options: Adaptive (Default) / Override
GT Adaptive Voltage Target (mV)
This item sets GT Adaptive Voltage Target, 0mV – 2000mV.

30
 TB85 & TB85-BTC UEFI BIOS Manual

GT Override Voltage Target (mV)

This item sets GT Override Voltage Target, 0mV – 2000mV.
(This item appears only when you set the GT Voltage Mode function to [Override])
GT Voltage Offset (mV)
This item sets GT Voltage Offset, -1000mV – 998mV.
Offset Prefix
This item selects the offset value as positive (+) or negative (-).
Options: + (Default) / -
VSA Voltage Offset (mV)
This item sets SA Voltage Offset, -1000mV – 998mV.
Offset Prefix
This item selects the offset value as positive (+) or negative (-).
Options: + (Default) / -
IOA Voltage Offset (mV)
This item sets IOA Voltage Offset, -1000mV – 998mV.
Offset Prefix
This item selects the offset value as positive (+) or negative (-).
Options: + (Default) / -
IOD Voltage Offset (mV)
This item sets IOD Voltage Offset, -1000mV – 998mV.
Offset Prefix
This item selects the offset value as positive (+) or negative (-).
Options: + (Default) / -
CPU Vcc Mode
This item sets CPU over Voltage Mode.
Options: SPEC Voltage / Auto / Offset Mode / Fixed Mode
CPU Vcc Offset
This item sets CPU Vcc offset, Voltage (0.1V-0.52V).
Options: Auto (Default)
CPU Vcc Fixed
This item sets CPU Vcc fixed, Voltage (1.5V-2.65V).
Options: Auto (Default)
CPU Vcc LoadLine
This item enables or disables CPU Vcc LoadLine control.
Options: Auto (Default) / Enabled / Disabled

31
 TB85 & TB85-BTC UEFI BIOS Manual

DDR Voltage
This item sets DDR(V_SM) Voltage configuration.
DRAM Configuration

Performance Memory Profiles

This selection of Performance Memory Profiles impacts memory sizing
behavior.
Options: Automatic (Default) / Manual / XMP Profile 1 / XMP Profile 2
Note: The following items appear only when you set the Performance Memory Profiles
function to [Manual]
Memory Clock Multiplier
This item allows you to set Memory Clock Multiplier.
Options: 1.33 (Default) / 1.00
Memory Frequency
This item allows you to set Memory Frequency
Options: DDR3 1333Mhz (Default) / DDR3 1066Mhz / DDR3 1600Mhz
tCL
This item allows you to select CAS Latency Range 4-18
Options: 11 (Default)
tRP
This item allows you to select Ras Precharge Range 1-38
Options: 11 (Default)
tRCD
This item allows you to select Row to Col Delay Range 1-38
Options: 11 (Default)

32
 TB85 & TB85-BTC UEFI BIOS Manual

tRAS
This item allows you to select Ras Active Time 1-586
Options: 28 (Default)
tWR
This item allows you to select Min Write Recovery Time Range 1-38
Options: 12 (Default)
tRFC
This item allows you to select Min Refresh Recovery Delay Time 1-9363
Options: 120 (Default)
tWTR
This item allows you to select Min Internal Write to Read Command
Delay Time 1-38
Options: 6 (Default)
tRRD
This item allows you to select Min Row Active to Row Active Delay Time
1-38
Options: 5 (Default)
tRTP
This item allows you to select Min Internal Read to Precharge Command
Delay Time 1-38
Options: 6 (Default)
tCWL
Minimum CAS Write Latency Time (tCWLmin)
Options: 8 (Default)
tREFI
Maximum tREFI Time (Average Periodic Refresh Interval).
Options: 6240 (Default)
tFAW
This item allows you to select Min Four Active Window Delay Time
1-586
Options: 24 (Default)
tRC
This item allows you to select Min Active to Active/Refresh Delay Time
(tRCmin) 1-586
Options: 39 (Default)

33
 TB85 & TB85-BTC UEFI BIOS Manual

BIOSTAR Memory Insight

DDR3 Information
These items display SPD information of DDR3 memory.

34
 TB85 & TB85-BTC UEFI BIOS Manual

7 Exit Menu
This menu allows you to load the optimal default settings, and save or
discard the changes to the BIOS items.

Discard Changes and Exit

Abandon all changes made during the current session and exit setup.
Save and reset
Reset the system after saving the changes.
Restore Defaults
This selection allows you to reload the BIOS when problem occurs during
system booting sequence. These configurations are factory settings
optimized for this system.
Launch EFI Shell from filesystem device
This item attempts to EFI Shell application (Shellx64.efi) from one of the
available filesystem devices.

35