® Badger Meter Europa GmbH

FMS Compact
Fluid Management System

Baby

USER MANUAL
November 2016

Firmware v3.7 until v5.16

LMS_FMS Compact_BA_02_1611
Contents Page

1. Basic safety recommendations ............................................................................................ 1

2. General description................................................................................................................ 2
2.1 Technical data................................................................................................................ 2
2.2 Front plate description ................................................................................................... 3
2.3 Connections ................................................................................................................... 4
3. Standard dispense procedure............................................................................................... 5
4. Supervisor menu: PIN 8888 (default) .................................................................................... 6
5. Installer menu: PIN 9999 (default) ......................................................................................... 8
6. General system reset ........................................................................................................... 12
7. Printer .................................................................................................................................... 13
7.1 Internal ticket printer .................................................................................................... 13
7.2 Internal or external ticket printer .................................................................................. 13
7.3 External report printer .................................................................................................. 13
7.4 Configuration external printer....................................................................................... 13
8. Barcode scanner .................................................................................................................. 14
9. Dispense modes ................................................................................................................... 15
9.1 Flow chart - Dispense Mode 0 and 1 .......................................................................... 15
9.2 Flow chart - Dispense Mode 2 ..................................................................................... 16
10. Warning and status messages.......................................................................................... 17
11. Dispense timing.................................................................................................................. 18
12. Manufacturer´s declaration ............................................................................................... 19
13. Warranty .............................................................................................................................. 19
14. DIN ISO certificate .............................................................................................................. 19

LMS_FMS Compact_BA_02_1611
Basic safety recommendations Page 1/19

1. Basic safety recommendations

Before installing or using this product, please read this instruction manual thoroughly.
Only qualified personnel should install and/or repair this product. If a fault appears, contact
your distributor.

Installation
Do not place any unit on an unstable surface that may allow it to fall.
Never place the units above a radiator or heating unit.
Route all cabling away from potential hazards.
Isolate from the mains before removing any covers.

Power connection
Use only the type of power source suitable for electronic equipment. If in doubt, contact your
distributor. Ensure that any power cables are of a sufficiently high current rating.
All units must be earthed to eliminate risk of electric shock.
Failure to properly earth a unit may cause damage to that unit or data stored within it.

Protection class
The device has protection class IP 42 and needs to be protected against dripping water,
water, oils, etc.

Setup & operation

Adjust only those controls that are covered by the operating instructions. Improper
adjustment of other controls may result in damage, incorrect operation or loss of data.

Cleaning
Switch off all units and isolate from mains before cleaning.
Clean using a damp cloth. Do not use liquid or aerosol cleaners.

Repair of faults
Disconnect all units from power supply and have it repaired by a qualified service person if
any of the following occurs:
 If any power cord or plug is damaged or frayed
 If a unit does not operate normally when operating instructions are followed
 If a unit exposed to rain/water or if any liquid has been spilled into it
 If a unit has been dropped or damaged
 If a unit shows a change in performance, indicating a need for service.

Failure to adhere to these safety instructions

may result in damage to the product or serious
bodily injury.

RoHs
Our products are RoHs compliant.

Battery disposal
The batteries contained in our products need to be disposed of as per your
local legislation acc. to EU directive 2006/66/EG.

LMS_FMS Compact_BA_02_1611
General description Page 2/19

2. General description
2.1 Technical data

Dimensions 20cm (7.9") x 30cm (11.8") x 13cm (5.1") W x H x D

CPU: Atmel, AT103 (AT128), 8-bit, serial flash,
128 K bytes of In–System programmable flash
Memory: Flash, 1Mbit
Interfaces: 9-pole RS232 plug to be use as
External printer, PC software or barcode reader
Baudrate 9600 - Parity none - Databits 8, LF/CR
Firmware update: With special serial adapter
Fuses F1 = Fuse controller 1.00 AmT/SB 250V
F2 = Fuse 12/24VDC 2.00 AmT/SB 250V
F3 = Fuse int.printer 5.00 AmT/SB 250V
F4= Fuse power supply 2.00 AmT/SB 250V
Pulse Input 4x NPN opto isolated
Valve Output 4x 24VDC, max.load 2A
Pump Control Relais, max. load 2A at 250VAC or 30 VDC (or 115 VAC)
Transactions 2999 max.
User 99 max.
Protection class IP57

LMS_FMS Compact_BA_02_1611
General description Page 3/19

2.2 Front plate description

Alphanumeric keypad

Function keys
Emergency stop

Ticket printer

Cable glands

LMS_FMS Compact_BA_02_1611
General description Page 4/19

2.3 Connections

01 PE 16 Valve 3 - 24VDC/2A
02 N 17 Valve 3 - GND
03 L1 230VAC/50Hz 18 Pulse Input 3 + 3
19 Pulse Input 3 GND
04 Valve 2 -24VDC/2A
05 Valve 2 - GND 20 GND
06 Pulse Input 2 + 2 21 +12VDC RS232 Port for software
07 Pulse Input 2 GND 22 +24VDC or external printer

08 Valve 1 - 24VDC/2A 23 Emergency Key

09 Valve 1 - GND 24 Emergency Key
10 Pulse Input 1 + 1 25 Pump Output Relay 5A/30VDC
11 Pulse Input 1 GND 26 Pump Output Relay

12 Valve 4 - 24VDC/2A F1 Fuse 1.0A SB 250V 5VDC

13 Valve 4 - GND F2 Fuse 2.0A SB 250V 12/24VDC
14 Pulse Input 4 + 4 F3 Fuse 6.3A SB 250V Int.Printer
15 Pulse Input 4 GND F4 Fuse 2.0A SB 250V 230VAC

Note: 230 VAC standard, optional 115 VAC

Flash tool RS232 serial port

connection

RS232 serial port

Ext. printer / PC software / Barcode reader
RXD = Pin 3
TXT = Pin 2
GND = Pin 7

Flash tool connection

For firmware update only for service

LMS_FMS Compact_BA_02_1611
Standard dispense procedure Page 5/19

3. Standard dispense procedure

Startup screen - displays of firmware version -----------------

-----------------
MINI
FLUID MGR SYSTEM
v5.14UK 18.11.12

02:42 13.02.08
Enter your 4-digit PIN-No. for the user
E N T E R
1111 (Default user by factory) PIN:
0000
Press key "OK"
Quit <= => OK

02:42 13.02.08
The user name is briefly displayed, the screen automatically
move to the next menu. *** Hello ***
User AAA
Enter your “order number”

Quit <= => OK

02:42 13.02.08
Enter your “Job Number” *****************
ENTER JOB NO.:
Alphanumeric entry, max. 15 digits *****************
FE67338
Confirm with "OK"
Quit <= => OK

Select Product:
Select fluid type on keypad or with arrow keys. Product 1 1
Product 2 2
Confirm with "OK" Product 3 3
Product 4

Quit <= => OK

02:42 13.02.08
Enter the requested quantity in liters.
ENTER Quantity:
Confirm with "OK"
_ L

Quit <= => OK

02:42 13.02.08
The system is now ready to dispense the fluid. Prepare
for
Dispensing
000001.00 L
Quit <= => OK

LMS_FMS Compact_BA_02_1611
Supervisor menu: PIN 8888 (default) Page 6/19

02:42 13.02.08
The display moves on count mode.

Once the fluid has been dispensed, the attached solenoid valve
will close and the internal printer will print a ticket.
000.00
000001.00 L
Quit <= => OK

4. Supervisor menu: PIN 8888 (default)

Set Date & Time Defines date and time
Date / Time :

27.01.08 11:13

Quit <= => OK

Transaction Rep An older ticket can be printed again.

Ticket #00012
Scroll with the left and right arrow to the desired transaction 27.01.08 12:37
and select PRT. User Name
See chapter 7.3 Product 1 1
000002.40L
Quit <= => PRT

Print Report Transactions report by date

Input begin-
Choose the desired time frame and confirm with OK. end date:

Note: The external printer must be activated. 13.02.08

START-DATE

Quit <= => OK

Stock Level Will print the actual stock levels

Stock Level:
T Level
Choose "PRT" to print or "Quit" to return 1: 000841.23L
2: 001211.78L
3: 000500.12L
4: 000467.08L
Quit <= => PRT

Prod. Delivery Fluid delivery can be added to the current stock (tank).
Select Product:
Product 1 1
Select a product and confirm with “OK” Product 2 2
or return with “Quit”. Product 3 3
Product 4

Quit <= => OK

Stock Level:
Enter the delivered quantity and confirm with “OK” Level:
or return with “Quit”. Product 1 1
000841.23L
Delivery:
000000.00L
Quit <= => OK

LMS_FMS Compact_BA_02_1611
Supervisor menu: PIN 8888 (default) Page 7/19

Set Stock Level Tank level correction

Select Product:
Product 1 1
Select a product and confirm with “OK” Product 2 2
or return with “Quit”. Product 3 3
Product 4

Quit <= => OK

Input new
Enter the new stock (tank) level and confirm with “OK” Stock Level:
or return with “Quit”. Product 1 1

000841.23L

Quit <= => OK

Supervisor PIN PIN 8888 can be changed.

Enter the PIN number and confirm with “OK” Input new PIN:
or return with “Quit”. 2
Supervisor
“Error” is displayed if the entered PIN number has already PIN: 8888
been allocated to another operator.
Quit <= => OK

Add new User To add a new user:

Enter new user name Add new User:
Enter PIN number with * key 4
Enter PIN number on keypad MUELLER
PIN: 4711
Confirm with "OK"
Return with "Quit"
Quit <= => OK

Delete User To delete an user:

USER : 4
Select user with arrow keys -----------------
MUELLER
Confirm with "OK" -----------------
Return with "Quit" !! r e m o v e !!

Quit <= => OK

LMS_FMS Compact_BA_02_1611
Installer menu: PIN 9999 (default) Page 8/19

5. Installer menu: PIN 9999 (default)

Products Defines a new product name. Select Product:
Product 1 1
Select a product and confirm with “OK” Product 2 2
or return with “Quit”. Product 3 3
Product 4

Quit <= => OK

Input new
Enter the new product name and confirm with “OK” Productname:
or return with “Quit”.
Product 1 1

Quit <= => OK

Set Min Stock Defines the minimum stock level (tank level), when system Select Product:
should give a warning message. Product 1 1
Stock Level: Product 2 2
000000.00 L Product 3 3
Product 4
Select a product and confirm with “OK”
or return with “Quit”. Quit <= => OK
Enter the new minimum stock level and confirm with “OK”
or return with “Quit”. Input Minimum
Stock Level:
Product 1 1
Only firmware v4.0 and later:
If the Set MinStock is set to zero, the warning is deactivated.
000050.00 L

Quit <= => OK

Set Mode Normal preselection mode or free dispense mode.

Dispense to:
Preselect 1 Product 1 1
Free dispense 2 Product 2 2
Product 3 3
Select a product and confirm with “OK” Product 4
or return with “Quit”.
Quit <= => OK

1
Enter the new operation mode and confirm with “OK”
-----------------
or return with “Quit”. Operation Mode 1
-----------------
Pre-select 1
Free Dispense 2
See also chapter: 9 Dispense modes Quit <= => OK

Initial Timeout Defines the delay after the PIN n° entry until the valve opens
Dispense to:
and the batch starts.
Product 1 1
Product 2 2
Select a product and confirm with “OK” Product 3 3
or return with “Quit”. Product 4

Quit <= => OK

Hose No.: 1
Enter the new timout and confirm with “OK” -----------------
or return with “Quit”. Timeout: 003
-----------------
in Seconds
from 0-255
See also chapter: 11 Dispense timing Quit <= => OK

LMS_FMS Compact_BA_02_1611
Installer menu: PIN 9999 (default) Page 9/19

Inact. Timeout If the pulse input from the meter stops before the preselected
Dispense to:
quantity has been reached, the system will wait for the defined
time before the batch stops and the valve closes
Product 1 1
(default 12 sec). Product 2 2
Product 3 3
Product 4
Select a product and confirm with “OK”
or return with “Quit”.
Quit <= => OK

Hose No.: 1
Enter the new timout and confirm with “OK” -----------------
or return with “Quit”. Timeout: 012
-----------------
in Seconds
from 0-255
See also chapter: 11 Dispense timing
Quit <= => OK

Install-PIN PIN 9999 can be changed

Enter the PIN number and confirm with “OK”

Input new PIN:
or return with “Quit”. 3
Installer
“Error” is displayed if the entered PIN number has already PIN: 9999
been allocated to another operator.
Quit <= => OK

Hose Calib. Calibration or scale factor for each hose (meter).

Dispense to:
System expects 100 PPL, will be displayed as 1.00 L
Note: Error caused by viscosity or density of the fluid.
Product 1 1
Product 2 2
Calibration CF: 10000 (can be read as 1,0000) Product 3 3
Product 4
Select a product and confirm with “OK”
or return with “Quit”. Quit <= => OK

Hose No.: 1
Enter the calibration factor and confirm with “OK” -----------------
or return with “Quit”. KF: 10000
-----------------
Cal.Constant
0.000001L/Pulse
Quit <= => OK

Hose Offset Will correct a difference between the

Dispense to:
preselected quantity and the actual dispensed quantity.
Note: Should be used by fix topoff error caused by a slow
Product 1 1
valve. Product 2 2
Product 3 3
Hose 1 Product 4
CO: 000000 Calibr. offset 0.000001 l
Quit <= => OK
For example:
CO: 003000 will shut off 0,03 l earlier.
Hose No.: 1
-----------------
Select a product and confirm with “OK” KO: 000000
or return with “Quit”. -----------------
Calib. Offset
Enter the hose offset and confirm with “OK” (0.000001L)
or return with “Quit”. Quit <= => OK

Print Parameter Will print the current configuration on the specified printer No sub menu.
for each hose

LMS_FMS Compact_BA_02_1611
Installer menu: PIN 9999 (default) Page 10/19

Setup Printer Printer selection

Printer: 1
0: No printer assigned -----------------
1: Internal ticket printer non 0
2: External printer internal 1
3: Internal and external printer
external 2
Int.&Extern. 3
Quit <= => OK

Clear Transact. Deletes all stored transactions.

-----------------
!!! WARNING !!!
-----------------
Proceeding will
delete all saved
Transactions
Quit <= => OK

Hose Linkage Defines which hose (meter) will be linked to a certain

Dispense to:
stock (tank).
Product 1 1
Product 2 2
Product 3 3
Select a product and confirm with “OK” Product 4
or return with “Quit”.
Quit <= => OK

LINKAGE
Enter the hose linkage and confirm with “OK”
or return with “Quit”.
Hose: 1
-----------------
Stock: 1

Quit <= => OK

Inac. Delay Defines how long the pump will keep running once the
Dispense to:
dispense has been completed.
Pump control has to be connected to terminal 25/26.
Product 1 1
Product 2 2
Product 3 3
See also chapter 2.3 and chapter 11 Product 4

Quit <= => OK

Hose: 1
-----------------
Stp.Delay: 002
-----------------
Stop Delay in
Seconds 0-255
Quit <= => OK

Scaling Unit Unit can be selected Dispense to:

Product 1 1
Display Meter must supply Product 2 2
0,00 L >> 100 PPL Product 3 3
0,00 m3 >> 100 PPm3 = 0,1PPL Product 4 4
0,00 hl >> 100 PPhl = 1 PPL
0.00 Gal >> 100 PPG
Quit <= => OK
Select a product and confirm with “OK”, or return with “Quit”.
Enter the unit and confirm with “OK” , or return with “Quit”. Hose: 1
-----------------
Scal.Unit: 0
Only firmware v3.7 Unit: 0: Liter 1:m3 2:hl -----------------
Only firmware v3.9 Unit: 0: Liter 1:kg 2:m3 0:Liter 1:kg
Later firmware v5.0 Unit: 0: Liter 1:kg 2:m3 3:Gal 2:m3 3:Gal
Quit <= => OK

LMS_FMS Compact_BA_02_1611
Installer menu: PIN 9999 (default) Page 11/19

Special Mode With Special Mode 0 the system will work as a standard Fluid
Special Mode: 0
Management System.
Mode 1 and 2 are customized dispense scenarios.
-----------------
See chapter 9. Standard 0
Direct Mode 1
Additive Calc 2
Only firmware v5.0 and later
Quit <= => OK

Scanner Will activate barcode scanner function.

Scanner: 0
See chapter 8.
-----------------
Disabled 0
Only firmware v5.0 and later Enabled 1

Quit <= => OK

Max. Dispense The maximum possible dispense:

Free Mode
4200,00 max. value (before 500)
Max.Dispense
Only firmware v3.9 and later
004200.00
(4200.00)
Quit <= => OK

Ticket Count The amount of tickets you would like to print.

Print Ticket
-----------------

Quantity: 1

(1 … 3)
Quit <= => OK

Additive This menu is only needed for Special Mode 2

Select Product:
See chapter 9.2
Product 1 1
Product 2 2
ppm = Parts per Million Product 3 3
Product 4 4

Quit <= => OK

Product:
Product 1 1

Factor:
100000 (ppm)

Quit <= => OK

Dispense TO Defines the maximum dispense time in seconds (10-600).

Dispense Alert
999 s will disable this function.
-----------------
If the dispense time is exeeded, the following message will be Timeout: 120
displayed: -----------------
in seconds
Dispense Alert
from 10 - 600
Dispense time exeeded
Printout will be started, X will indicate the Hose No.:
Quit <= => OK

Dispense time exeeded: X

Only firmware v5.10 and later

LMS_FMS Compact_BA_02_1611
General system reset Page 12/19

6. General system reset

This function will reset and erase the FMS Compact (only firmware v3.9 and later)
Note: System will be set to factory default data.

Procedure:
Unplug the FMS Compact and press the button 1 and 2.
Keep the buttons pressed and plug in the power supply.

!!! CAUTION !!! ARE YOU SURE ? ARE YOU SURE ?

This procedure
will erase and Quit: Cancel Quit: Cancel
reset the device. OK: Proceed OK: Proceed
xxxx of 2126

Quit <= => OK Quit <= => OK Quit <= => OK

LMS_FMS Compact_BA_02_1611
Printer Page 13/19

7. Printer

7.1 Internal ticket printer

To change the paper roll, please proceed as follows:
 Open the printer cover and press down "Push".
 Insert the end of the paper roll in the slit of the print mechanism and position the paper
roll so that it rotates in the right direction, as shown below.
 The paper is automatically pulled by the roller for 3 or 4 cm.
 Tear off the paper and re-close the cover.

Note: Make sure the paper edge is straight before inserting it in the machine.

7.2 Internal or external ticket printer

25.05.11 15:12
H.Mueller
458534
SAE15W40 1
L 000004.52

7.3 External report printer

Date : 31.05.11 ** Transaction Report ** Time: 22:39

No. Date Time Job Nr. Qty. Product Technician

00017 25.05.11 15:12 458534 000004.52 SAE15W40 1 H.Mueller

00018 31.05.11 17:15 54215 000008.19 SAE30W40 2 H.Maier
00019 31.05.11 17:17 1200 000001.65 SAE30W40 2 H.Mueller
00020 31.05.11 17:18 52354 000001.76 SAE30W40 2 H.Mueller
00021 31.05.11 17:23 526585 000007.23 SAE15W40 1 H.Schulze
00022 31.05.11 17:30 585545 000005.15 SAE90 3 H.Mueller
00023 31.05.11 18:44 1234 000001.30 Gear oil 4 H.Mueller
00024 31.05.11 18:47 654852 000001.09 SAE30W40 2 H.Schulze

7.4 Configuration external printer

RS232 Baudrate 9600, Databit 8, Parity None, StopBit 1
Connection 25-pole D-SUB RXD PIN 3, TXD PIN 2, GND PIN 7

LMS_FMS Compact_BA_02_1611
Barcode scanner Page 14/19

8. Barcode scanner

The serial port of the FMS Compact can be connected to a barcode scanner. It will work
parallel to the existing keypad. You always have the choice to use the keypad or the
scanner.

Note: If the barcode is activated, the PC software or external printer port cannot be used
anymore.

Connection: RS232, D-Sub 25-pole, 9600 Baud, 8 DataBit, ParityNone, 1 Stop Bit

Recommended barcode scanner: Datalogic Gryphon, Datalogic Magellan 1000i

Barcode sample

PIN number 1111 [CR] [LF]

Job number 123456789012 [CR] [LF]

Hose selection 1 [CR] [LF]

Quantity 1.5 [CR] [LF]

Dispense start *Start* [CR] [LF]

Quit *STOP* [CR] [LF]

Enter [0x14] [CR] [LF]

End suffix:
Each tranmission from the barcode scanner must be followed by a CR and LF control
signal.
CR = ASCII (13) = Hex (0x0a)
LF = ASCII (10) = Hex (0x0d)

Barcode scanner only available in firmware v5.0 or later.

LMS_FMS Compact_BA_02_1611
Dispense modes Page 15/19

9. Dispense modes
9.1 Flow chart - Dispense Mode 0 and 1

Enter PIN
Number:

1111

Quit <= => OK

** Good day **
MR.MUELLER

Quit <= => OK

****************
Job Number Menu Special Mode
**************** Direct mode = 1
1234 System will not ask for the job number

Quit <= => OK

Linkage:
SAE15W30 1
SAE90W10 2
Gear Oil 3
Coolant 4
Quit <= => OK

MenuSet Mode
Quantity: Free dispense = 2
No preselection. The dispense starts immediately
3,5 L

Quit <= => OK

Ready Ready
to to
dispense dispense

00003.50 L 04200.00 L
Quit <= => OK Quit <= => OK
The batch will stop when :

003.50 007.40 STOP - Button

00003.50 L 04200.00 L
Quit <= => OK Quit <= => OK

No flow detected, the attached

valve has been closed
Ticket printout Ticket printout manually. Can be adjusted in
menu "Inactive Timeout".
22.03.07 15:31 22.03.07 16:24
MR.MUELLER MR.MUELLER
1234 1234 The max. dispense quantity has
SAE15W30 1 Product one 1 been reached. Can be adjusted
Liter: 000003.50 Liter: 000007.40 in menu "Max. Dispense".

LMS_FMS Compact_BA_02_1611
Dispense modes Page 16/19

9.2 Flow chart - Dispense Mode 2

Customized dispense flow, will calculate a required quantity based on a preconfigured factor.
Dispense will start with the Job Number request, no PIN number entry requested.
System will use the first user as the default user.
Administration Menu
****************
Changes to the Supervisor ** Good day **
Gas Delivery PO#
menu, if the Supervisor PIN Supervisor
****************
123456789012 has been entered.

Default 8888 or 9999

Quit <= => OK Quit <= => OK

Dispense to:
Product 1 1
Product 2 2
Product 3 3
Product 4 4
Select Additive
Quit <= => OK
Product 1
Product 2
Delivered Product 3
Quantity of fuel Product 4
Values bigger than <16,000
5000 Gal will be blocked. Quit <= => OK

Product
Quit <= => OK
Product 1

Calc.Quantity of FactorPPM 000372

additive:

1.86 Gal Quit <= => OK

Product
Quit <= => OK Product 1

Ready FactorPPM 000419

to
dispense Quit <= => OK
00002.86 Gal Product
Quit <= => OK Product 3
Product 3
FactorPPM 000372

000.00 The batch will stop when :

Quit <= => OK
00001.86 Gal STOP-Button Product
Product 4
Quit <= => OK
FactorPPM 000329
No flow detected, the attached
valve has been closed manually.
Can be adjusted in menu Quit <= => OK
Ticket printout "Inactive Timeout "

03-10-11 15:31 The max. dispense quantity has

Ultrazol 9888 been reached. Can be adjusted
PO# 123456789012 in menu "Max.Dispense"
Fuel Gal 5000
Product 1 1
Gal 000001.86

LMS_FMS Compact_BA_02_1611
Warning and status messages Page 17/19

10. Warning and status messages

The requested quantity has been higher than specified quantity in the
!INPUT - ERROR !
Menu Max.Dispense - Page 11
Maximum dispense
quantity exeeded

Quit <= => OK

02:42 13.02.08
Dispense has been stopped with "Pulse Time Out".
No pulse are arriving from the meter, the Inactive Timout has been exeeded.
001.34 See also page 9 - Inactive Timeout
00003.50 L
Pulse Timeout

03:25 13.02.08
The minimum tank level has been reached, to be defined in the
!!! WARNING !!!
Menu Set Min Stock - Page 8
S T O C K
E M P T Y
000015.00 L
Quit <= => OK

Dispense Alert
The maximum allowable dispense time has been exeeded, to be defined
Dispense time in Menu Dispense TO - Page 11
exeeded
Pulsating beep tone will start.

PRESS KEY PRESS Only firmware v5.10 and later

PULSE ALERT
An unexpected pulse input arrived while the solenoid valve is closed.
Valve Stuck open
A pulsating beep tone will start.
Press any key to If this problem persist, please ask the service personnel.
clear error A leaking valve could be the cause.

PRESS KEY PRESS Only firmware v5.10 and later and Dispense Mode 2

LMS_FMS Compact_BA_02_1611
Dispense timing Page 18/19

11. Dispense timing

Master Valve or Pump Control will Only one dispense can be done at a
be active if there is an ongoing time. Other meters will be blocked.
Relay closed dispense.
MasterValve or
PumpControl
Connection
Potential free relay

t
Relay closed

Ongoing dispense Hose 1, 2, 3, 4

to solenoid valve
Connection 4 (5,6,7)
Relay activates 24VDC
t
Dispense Dispense Main pump
starting stopped stopped

Inititial Timeout Inactive Delay

See configuration (page 8) See configuration (page 10)
- Delay can be adjusted from 0-255s - Delay can be adjusted from 0-255s
- For each additive separate - For each additive separate

LMS_FMS Compact_BA_02_1611
Manufacturer´s declaration / Warranty / DIN ISO certificate page 19/19

12. Manufacturer´s declaration

You will find all CE declarations applying to this meter series under
www.badgermeter.de/service/CEdeclarations.

13. Warranty
Badger Meter warrants meters and parts manufactured by it and supplied hereunder to
be free from defects in materials and workmanship for a period of 24 months from date
of shipment. If within such period any meters or parts shall be proved to Seller´s
satisfaction to be defective, such meters or parts shall be repaired or replaced at Seller´s
option. Seller´s obligation hereunder shall be limited to such repair and replacement and
shall be conditioned upon Seller´s receiving written notice of any alleged defect within 10
days after its discovery and, at Seller´s option, return of such meters or parts to Seller,
f.o.b. its factory. THE FOREGOING WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL
OTHER EXPRESS OR IMPLIED WARRANTIES WHATSOEVER INCLUDING BUT
NOT LIMITED TO IMPLIED WARRANTIES (EXCEPT OF TITLE) OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Badger Meter
shall not be liable for any defects attributable to acts or omissions of others after
shipment, nor any consequential, incidental or contigent damage whatsoever.

14. DIN ISO certificate

Please refer to our valid DIN ISO certificate under
www.badgermeter.de/service/certificates.

LMS_FMS Compact_BA_02_1611
Hotline
Tel: +49-7025-9208-0
Fax: +49-7025-9208-15
E-Mail: badger@badgermeter.de

Please contact your supplier for any assistance you may need.

® Badger Meter Europa GmbH

Subsidiary of Badger Meter, Inc.

Nürtinger Strasse 76
72639 Neuffen (Germany)
E-Mail: badger@badgermeter.de
www.badgermeter.de