Cts 11-12 Service Manual Complete

Donated by John & Susan Hansen - For Personal Use Only
MOTOR TRUCK SERVICE MANUAL

______
CTS-11 FOR L-LINE TRUCKS
AND
CTS-12 Supplemental Pages, for R-LINE TRUCKS ONLY John & Susan Hansen, November, 2009
III
MOTOR TRUCK
SERVICE MANUAL
CTS-11 FOR L-LINE TRUCKS
AND
CTS-12 Supplemental Pages, for

R-LINE TRUCKS ONLY
NOTE: Use CTS -11 Manual for R.. LI NE units other than shown in CTS ..12 Supplemental pages.
INTERNATIONAL
L-LINE MOTOR TRUCKS

SERVICE MANUAL
CTS-11
This manual has been compiled in a simple, non-technical manner and every effort has been made to cover the most important items. It will provide a convenient reference source for the serviceman. Wherever possible, repetition of service instructions has been avoided by combin ing truck or unit models. An index at the front of each group permits locating items covered in a particular Group. Where necessary, groups have been subdivided into sections. As additional data is compiled, new or revised pages will be issued. These should be inserted in their respective group and section. IMPORTANT: Before starting any overhauling work, always remove the dirt that has accu mulated around the parts to be disturbed. When parts are taken off, dirt not removed may fall into the units, contaminating the lubricating oil, and getting into bearings and other working parts. As dirt contains grit and abrasives, considerable unnecessary wear and reduction in effi ciency is invariably the result.
Motor Truck Division
INTERNATIONAL HARVESTER COMPANY

180 NORTH MICHIGAN AVE. CHICAGO I, ILLINOIS
1993-2009 International Truck Intellectual Property Company, LLC, Warrenville, IL,

a wholly owned subsidiary of International Truck & Engine Corporation, Chicago, IL.
All rights to this book are reserved. No part of this book may be reproduced in any
manner without express written permission from International Truck Intellectual
Property Company, LLC.
Printed and distributed under license from International Truck Intellectual Property
Company, LLC by S & C International Inc, dba Binder Books.
Binder Books is located at 27875 SW Grahams Ferry Rd, Sherwood OR 97140.
Phone: 503-682-9328; FAX: 503-682-9563; www.binderbooks.com
IHC, TRIPLE DIAMOND, SCOUT, TRAVELALL and INTERNATIONAL, are
trademarks licensed by International Truck Intellectual Property Company, LLC.
CHECKING LIST AND INDEX

FOR
R-LiNE SUPPLEMENT TO THE
CT S-11 L-LINE MOTOR TRUCK
SERVICE MANUAL
NOTE: INSERT THESE R-LINE SUPPLEMENTAL PAGES IN THEm RESPECTNE SECTIONS IN THE CTS-ll SERVICE MANUAL
The attached pages contain only those major units us ed on R-Line trucks which are not common to units used on the respective L-Line trucks . Only the service specifications and data for the R-Line major units are covered in these pages. Additional R-Line coverage will be released when available. Description Axle, Front. . . . . . . . Axle, Rear . . . . . . . . . Bodies, Cabs and Cowls. Clutch . . . . . . . . . . . . Electrical. . . . . . . . . . . . Electrical System (Circuit Diagram) Electrical System (Illustrations) . Electrical System (Illustration). Engines . . . Fuel System Instruments Lubrication. Section Specifications SpecificaHons A
A
Page
1, 2
Specifications
A E J
Specifications Specifications
A A
1 thru 1 thru 1 thru I, 2 1 1 thru 1 thru 1 1 thru
4
4 7 4 4 3
IH
INTERNATIONAL
HARVESTER
CTS IZ-MARC!1 1953 (Supplemen ! p."e. for CTSI I),
PRINTED fN UNITED ST"TES OF' ""'HHHeA-.
L-LINE MOTOR TRUCK SERVICE MANUAL
GENERAL
Index
Page 1
GENERAL INFORMATION GROUP

INDEX
Page Abbreviations for terms of weight and measure
Ability formulas . . . . . . . . . .
Ball and roller bearing maintenance
Cold weather recommendations . . .
Conversion chart - liquids (British Imperial and U. S. Measure).
Conversion chart - Fahrenheit to Centigrade, altitude - barometric pressure,
altitude - boiling points . . . . . . . Engine lubricating oil recommendations . Equivalent values of electrical, mechanical and heat units Free inspection during warranty period . . Glossary of technical and mechanical terms Inspection of new trucks before delivery . . Instructions to owner at time of delivery of new truck Key to symbols used in mathematical formulas Ma terials returned for inspection . . . . . Mathematical formulas used in transportation engineering. Motor truck complaint forms . . . . . . . . . . . . . . Pounds - G. V. W. which 1 H. P. (at clutch) will pull up various grades Road - Engine speed formulas Steel and its heat treatment
Units of weight and measure.
Vehicle specification card (on dash) .
Weights, measures, equivalents . . . .
34
35
9, 10
8, 9
34
35
28, 29, 30
14 to 24
1
31
5
31
2 to 5
32, 33
33
10 to 14
26, 27, 28
6
24. 25, 26
PRINTED IN UNITED STATES OF "MERleA
WARRANTY
THE INTERNATIONAL HARVESTER COMPANY

warrants each new INTERNATIONAL MOTOR TRUCK to be free from defects in material and workmanship under normal use and service, its obligation under this warranty being limited to making good at its factory any part or parts thereof which shall be returned to it with transportation charges prepaid, and which its examination shall disclose to its satisfaction to have been thus defective, provided that such part or parts shall be so returned to it not later than ninety (90) days after delivery of such vehicle to the original purchaser, and that at the time of such return, the said vehicle shall not have been operated in excess of frve thousand (5,000) miles. This warranty is expressly in lieu of all other war ranties expressed or implied and of all other obligations or liabili ties on its part, and it neither assumes nor authorizes any other person to assume for it any other liability in connection with the sale of its vehicles. This warranty shall not apply to any vehicle which shall have been repaired or altered outside of its factory in any way so as, in its judgment, to affect its stability or reliability, nor which has been subject to misuse, negligence or accident, nor to any commer cial vehicle made by it which shall have been operated at a speed exceeding the fadory rated speed, or loaded beyond the factory rated load capacity. It makes no warranty whatever in respect to tires, rims, ignition apparatus, horns or other signaling devices, starting devices, gener ators, batteries, speedometers or other trade accessories inasmuch as they are usually warranted separately by their respective manu facturers.
L-UNE MOTOR TRUCK SERVICE MANUAL
GENERAL Section Page 1
INSPECTION OF NEW TRUCKS BEFORE DELIVERY
When trucks corne off the assembly line at the factory they have already been given numerous unit inspections and in addition are subjected to a driving test and final inspection. Districts and Dealers should, however, recheck each truck prior to delivery to a customer. This is particularly advisable if trucks have been driven through or "double decked" by a drive-away company.
It is the responsibility of each District and
6. Check cooling system for water. 7. Install battery, checking specific gravity and level of electrolyte. 8. Warm up engine and check operation of instruments and lights. 9. Tighten cylinder head and manifold nuts uniformly, using tension indicating wrench. (If truck has not been driven since leaving the factory, this operation is unnecessary.) 10. Adjust valve lash if necessary. Note: If head is tightened in operation (9), valves in overhead-valve engines will require ad justment. 11. Check and adjust carburetor for idle. 12. Check tire alignment on wheels. if necessary. Tighten rim lugs. 13. all hub stud nuts. Correct
Dealer to see that new trucks are delivered to users in a fault-free condition. This will mean a satisfied owner and will tend to eliminate unnecessary trips to the Service Station for minor adjustments during the warranty period. The pre-delivery service at each District must include all of the operations listed below: 1. Clean and polish truck if necessary. 2. Lubricate chassis, and check oil in air cleaner. 3. Check lubricant level in transmission. 4. Check lubricant level in differential. 5. Check oil level in engine. Drain and refill if oil is not of proper viscosity for locality or season, or if truck has been driven any great distance.
14. Check front wheel alignment for toe-in of wheels. 15. Install tools, spare rim, and owner's manual, etc. 16. Give truck short road test, checking brakes, controls, and general handling, to assure that all are functioning properly.
INSTRUCTIONS TO OWNER AT TIME OF DELIVERY

OF NEW TRUCK
As a rule, the purchaser's first impression is a lasting one, therefore it can easily be under stood that trucks should be in perfect mechanical condition at the time of delivery. The operation and care of the truck should be thoroughly ex plained to the owner at this time.
It is that the following instructions be given purchaser at the time of delivery of the truck:
6. Importance of proper clutch pedal clearance

in prolonging clutch life. 7. Cover lubrication of truck completely, point out hazard and costliness of neglect. 8. Advise owner to register such units as batteries, electrical units, etc., with the local authorized dealers of that equipment. 9. Point out advantages of bringing truck to the International Service Station at specified intervals during the warranty period of inspection, at which time there may possibly be some minor adjustments advisable. These, if made, will aid in prolonging the life of the truck. 10. Stress the benefits of using only International Service parts and the advantages of having service work performed in International Service Stations or by International Dealers.
1. General information covering the construc tion and operation of the truck. 2. Advice as to the proper grade of lubri cating oil. (See Lubrication Section.) 3. Explanation of the function, purpose, and maintenance of the oil filter. 4. Explanation of the function, purpose, and maintenance of the air cleaner. 5. Cover proper draining of the cooling system and the importance of using recommended anti-freeze solutions when necessary.
PRINTEO IN UNITED STATES
O~
AMERICA
GENERAL
Section Page 2
PIILfHED IN U .. llfb Sl,I;T(S

or
",HRICA
REPORT OF
MOTOR TRUCK COMPLAI NT

INTERNATIONAL HARVESTER COMPANY
MAIL 5 COPIES TO GENERAL OFFICE, CHICAGO MOTOR TRUCK SERVICE SECTION
SERIOUSNESS Of FAILURE IS BASED UPON THE NUMBER Of COMPLAINTS RECEIVED, REPORT , - - - - - - - - - - - - - - - - - - -

EACH CASE UNTIl YOU HAVE BEEN INFORMED Of REMEDY BY BULLETIN OR GENERAL LETTER.
If REMEDY FAILS. EACH CASE MUST BE REPORTED.
DISTRIBUTION
DISTRICT OFFICE Distri ct
DATE~__~6_-~8_-~4L9________
BRANCH _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ IS
REPLY DESIRED?
SUPERVISOR OF INSpECTION
6TH FLOOR. G_ 0.
FT, WAYNE
SERVfCE e:NGJNEe:R
WHEN REPORTING ON UNITS SUCH AS CAB, AXLE, TRANSMISSION. ETC., SERiAl NUMBER OF UNIT MUST BE GIVEN, Be sure to give
UNIT SERIAL NO. COMP1.AINT DETAI1.S failure to Engine when this loss hot. information. of power and
SALgS Se:RVICE: SECTION

CHIEF INSPECTOR CHIEF lNSPECTOR CHIEF INSPECTOR
FT
WAYNE:
FT. WAYNE WORKS

INDIANAPOLIS WORKS
SPRJNGFlELO WORK'S FT, WAYNE

METROPOLITAN BODY CO.
start
SERViCe: PARTs DEPT.
WORKS MANAGER
DELIVERY DATE
7-<-/1.$
TOTA1. MI1.ES TO DATE 14,289
OWNERL-_~N~a~m~e_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ cITY_~A~d~d~r~e~~~~~s~-------
MODEI~__~L~-~2~1~O~____ WHEE1.BASE~~1~4~9L_"_______
$675
AIS, HO RAD! DRS, WINDSHiElD WIPERS. GLASS, IONS, PH LER SHAfTS, FRAMES, WHEELS, ETC..
THE fOLLOWING INFORMATION MAY BE OMITTED IN CASE OF FAILURE ON MINOR UNITS SUCH AS SHEET METAL. INSTRUMENTS, ETC. BUT ON MAJDR UNITS SUCH AS AXlES, ENGINES, CLUTCHES, FILL OUT CDMPLETELY.
STRAIGHT TRUCK TRACTOR &. TRAILER
MAX, PAY1.0AD________________ MAX, PAYLOAD____~~~~~-----
Aft RATIO
6. 5 - 8.86-1
SINGL'"E_____
(PO"'iT) (......)
TOTAL GROSS WT._ _ _ _ _ _ _ _ _ _ TOTAL GROSS WT_<=-f--"'-=-'''-'t--'''''--. TIRE SlzdO: OOX2O,UAI 10: OOx20 TRUCK BODY TYPc.E_______________
rc.._~"'-"'''''-'''-'''---COMMODITY
TRAILER BODY Axle
HAULEr:Misc
.Freight
TRUCK BODY SIZE

(LIrHGJ'rH
WiD'1'LOngT)
SIZE~6.-~.il'II~.u.~::::c- WHO MOUNTED BODY

HEIGHT)
Tra~1mo b ' l e ' 1

,~
1.0CA1. OR LONG DISTANCE Distanc-filyPE OF ROADS,-,,:-.:::::-!-=...c=rWHO MAl NTAI NS
AVER.
SPEED~M.P.H.
SERVICEI:.--'I""-H~C'__'an~d""--'O"-'wn=.::::e_~'r__-
'--_ _ _ 1.ABOR_____ GRATISED
WHAT ALTERATIONS HAVE BEEN MADE BY DISp.1..u.........."AT':.J.J,."'-""';..... LER OR CUSTOMER ON ANY PART RE1.ATED TO THE FAI1.URE?
Name INVESTIGATED BY____~~~~____~~__~__- -__~-------------REMARKS_____________________
POSITION___________________________
WE WIL1. WELCOME SUGGESTED REMEDIES WHICH HAVE BEEN TRIED AND PROVED SUCCESSFU1.. SIGNED,_____=S~i~g~na~t=ur~~e~~~~~~~---------SERVICE MANAQER OR FOREMAN
v." Reoor.e Side for Additiorw! Remarb. A Separau Letter CompUcate. and Delay. Action.,
APPROVED
Signature
~D~'S~T~HI~C~T~M~A~N7AG~E~R~-------------
A-23214
MOTOR TRUCK COMPLAINT FORMS
Two fOrITIs, CT-6 and GF-70, are used to pro vide a continuous flow of information frOITl the Districts through the General Office to the various Works and DepartITlents regarding the perforITl ance of our product in service and as a final check on the condition of our product as re ceived by the Districts. This information is of utmost importance to our Manufacturing and Engineering Departments in maintaining the high quality of our Product. Therefore, the task of guarding the quality of our product rests largely with our District Organi zation. This task can best be performed by the District reporting complaints on the regular com plaint forms. All complaints, both CT-6 and GF-70 forITls, re ceived by the Motor Truck Service Section, Chicago, are given wide circulation through our Engineering and Manufacturing Departments and to interested parties in our Chicago General Office. These complaints provide a rapid and accurate flow of information to our Works In spection DepartITlents so that necessary cor rective action can be taken to eliminate the cause of such complaints proITlptly. The necessity for a remedy is based entirely on the seriousness of the complaint. The serious ness of a complaint is based on the number of those complaints received. The following instructions and suggestions are for your assistance in making out and sub mitting these forITls: Motor Truck COITlplaint forITl CT-6 is to be used in cases of serious failures where assistance is solicited by the District in the solution of a pressing service difficulty for which the District is unable to find an answer. This form should also be used in reporting complaints where the complaint is contributed to by loads or operating conditions and the information requested on the forITl is necessary for the complaint to be properly analyzed. Product Report form GF-70 is to be used largely during the warranty period in reporting failures or cOITlplaints on current models on which no immediate assistance is needed. This form should also be used in reporting failures or complaints on new parts and assemblies from our Service Parts Department and in reporting unfavorable custOITler reaction to design or
PRINTED IN UNITD STATES OF AMERICA
material, unsatisfactory perforITlance or diffi culty of servicing our trucks.
1. ALL COMPLAINTS concerning which the territory has not been advised of a remedy, must be reported. In other words, you are to continue the reports on all trouble until advised of a remedy or correction.
2. Complaints concerning which the territory has been advised of a remedy should not be reported; except in cases where the remedy itself fails; and except in such cases where the Service Bulletin announcing the remedy advises that Complaint Forms are necessary in order to obtain credit frOITl the Vendor. Then so state under "Remarks." 3. Complaints on each unit must be covered on a separate and proper Complaint ForITl except in the case of trucks where the same unit fails on several trucks of the same fleet; you may use the same form but list the chassis, engine and unit serial number of each truck involved.
4. It is importaritJhat the unit serial number be given in the space provided on form CT-6 Bulletins have advised the location of the serial numbers on the various units. The ITlajor part nUITlbers affected should be shown in the space provided on GF-70 forms,
5. State the complaint clearly on form CT-6

under the heading Complaint Details and on form GF-70 under the heading Complaint. For instance, if you are reporting the failure of a "Rear Axle Shaft" state "Rear Axle Shaft Failure" (left or right). Do not just state "Rear Axle Failure. It 6. If you believe certain ITlaterial should be re turned for inspection, state under "Remarks" that the material is being held, and hold material for thirty days after acknowledge ment of complaint has been received, unless disposition is given in the ITleantime. Hold parts covered by GF-70 forms for 30 days after submitting forITl. 7. All material returned should be properly packed and tagged so that it can be identified and, in addition, should bear the "Returned for Inspection" tag, Form CTS-l, filled in properly and completely. (See General letter MT No. 11, 4-21-49).
GENERAL
Section Page 4
MOTOR TRUCK PRODUCT REPORT

DAT~E
__~1-~1~5~-4~9~__________
COMPLAINT SPEEDOMETER CABLE-.llB.OLEJLJmE TO CABLE RAVING
SERVICE MILEAGE
(ON PART INVOLVED)_ _.-:::.8::o:4"'-O_ _ __
_______--=<.BEE""t;'''''N'--'''.!IN'-''S'cT~..sHARP
KI~Rl1'lHEEL
TYPE OF SERVICE:
LONG DISTANCE
DUMP
-------AlREMED_IA-:NEW CABLE ..
AS~NB'I'ArJ,ED
AND
_____..._____~~_.o'_PEQF~R01ITEll.. ____________ i
.0 .0 .0 .0 .0
.[iJ
:Ej
DISTRICT OFFICE~TR.lC'1'_ . - - - -... --.---.-.. ~--_ci SIGNED_.. . --.!N=A=ME=--_____
1.
rs where assi.ldllce is necessary or where an acknowledg.

2.
Motor Truck DiVision

Service Section
3rd Annex
180 N. Michigan Ave.
Chicago I, Illinois
3. 4.
s n unimproved parts or assemblies when an improvement has already boon field by bulletin or otherwise.
A-23215

8. It has been the practice in the past for the Servic Supervisor to make out the CT-6 forms and submit them to the District Manager for his signature. This has caused some delay where the Service Supervisor is in charge of both motor truck and general line service, as it has been necessary for him to spend much time on the territory, resulting in the Complaint Forms not being made out and submitted promptly after the failure occurs. The logical time to determine if a failure should be covered on a CT-6 or GF-70 and to gather information for the Form is when the truck is in the Service Station and the repairs are being made. Therefore, when the Service SupeTvisor is away, the Service Foreman should gather the information and make out the CT-6 or GF-70 form, in order that they can be sub mitted as quickly as possible after the failure occurs.
11. Copies of the complaint reports, GF-70 and CT-6, ar e to be distributed as follows: 5 copies to Chicago Service Section. 1 copy for District Manager. 1 copy for Service Station files. 12. The District Manager should review his complaint file monthly with the Service Supervisor and personally follow up with the respective Service Divisions of the Chicago Office all cases where no remedy has been provided. We cannot emphasize too strongly the import ance of making prompt and complete reports on all complaints that should be brought to the at tention of the Engineering, Manufacturing or Sales Department at Chicago. Examples of CT-6 and GF-70 Complaint Forms properly filled out are illustratedonpreceding
9. Much information, which would be valuable in assisting the various Departments in diagnosing and developing remedies for the complaint, can and should be given under the caption "Remarks" or on an attached sheet. For instance: a clear description of the failure; the Service Supervisor or the Service Foreman's opinion of the cause of the failure; his idea of a remedy, if any; the results of his remedy if applied; any local climatic conditions that are peculiar and have bearing on the complaint; any un usual operating conditions that might play a part in the complaint; and, in short, any information, additional to that requested on the form, which has any bearing on the com plaint, should by all means be given. This means that a thorough investigation of the complaint should be made by the Service Supervisor or Foreman before attempting to make out the Complaint Forms. 10. In the past it has been the general prac tice for the Branches to make out CT-6 forms and forward them to the District for the Service Supervisor to check and for the District Manager's signature. This, in some instances, has caused considerable delay in submitting these forms to the Chicago Office. We suggest that the Ser vice Station Foreman at each Branch should make out the Complaint Forms and submit them to the Branch Manager for signature and forward direct to the Chicago Office. An extra copy, however, should go to the Dis trict office for the District Manager's files. GF-70 forms may be made out and signed by the Service Supervisor, Service Station Foreman and A & H Foreman. Branches should send one copy of each GF-70 form to the District office for the District Manager' s files.
PRINTED IN UNITED STATES OF AMERICA
Materials Returned for Inspection

RETURNED FOR INSPECTION TAG, FORM CTS-l is especially prepared and adapted to portray all necessary information if and when properly filled in. It is designed to be used on all shipments of materials sent in for inspection other than surplus repairs. The following special instructions must be ad hered to in the use of the card: 1. Obsolete or defective parts must not be returned unless authority is granted. 2. The CTS-I Tag must be attached to all shipments of materials sent in for inspec tion other than surplus repairs or exchange units such as crankshafts. 3. Shipping charges must be prepaid. 4. All blank spaces on tag must be filled in to portray necessary information. 5. Tag should be made out in ink or hard pencil to avoid obliteration during shipment. 6. Attach tag to parts rather than to package to avoid loss when unwrapping. 7. Refer to date of CT-6 Complaint Form or GF-70 Form if such has been issued. 8. Where possible, report unit serial numbers of such units as Engines, Cabs, Trans missions, Axles, etc., when reporting con cerning these units. To avoid the necessity of writing separate letters, it is generally possible to include all general information under the caption "REMARKS."
GENERAL
Section Page 6
VEHICLE SPECIFICATION CARD

LOCATED ON DASH INSULATOR PANEL, ABOVE CLUTCH AND BRAKE PEDALS ON MODELS L-160 AND UP
VEHICLE
SPECIFI CATIONS
DESCRIPTION SERIAL NO. CODE VARIATIONS
GVW
1180271_ _ __
1209C 1250 1307AD

1 4 1 2 =8-=C'--_ __
1. 46 B
1928F
01 2ACDG
0418
o
D
092
EXAM PLE
A new procedure for handling Service Parts has been placed in operation at the International Motor Truck Service Parts Department. With this new system in operation, it is expected that the vehicle owner will realize many benefits from a service standpoint, particularly when ordering replacement parts for his truck. The system consists of assigning code numbers to the units included in the vehicle, such as: engine, transmission, cab, rear axle, wheels, etc. This same code number is used during the manufacture of the vehicle and will be further carried over into the parts catalogs which apply to the particular mode 1 trucks. By this means, a common langu.age has been set up for all parties involved in the design, the use, and the servicing of this particular vehicle. Code numbers are assigned only to those units to which the customer has an optional choice. The code numbers assigned to the units on the L-160 Models and up have been printed on a "Vehicle Specification Card" which is included with the truck and is located on the dash insu lator panel directly above the clutch and brake pedals. The parts catalogs are subdivided into sections identical with code numbers shown on the "Vehicle Specification Card." When ordering parts for the truck, it is irrlportant to include with the order the inforITlation con tained on the "Vehicle Specification Card" which pertains to the unit for which the parts are being ordered. For exaITlple, if it becaITle necessary to order a countershaft for the transmis sion on the vehicle shown on the sample "Vehicle Specification Card" it would only be necessary to indicate on the order that a countershaft for the L-181, F-51 OD transmission, under code number 1307 AD was needed. From this information it can be quickly determined just which part should be supplied. The "Vehicle Specification Card" will prove of great value to the customer when entering the Service Station for Service work, since refer ence to the card will indicate to the Service Station just what units are included with the vehicle and will put them in a position to render the best possible service. Be sure to keep the "Vehicle Specification Card" with the vehicle at all times.
FREE INSPECTION DURING WARRANTY PERIOD

1. First Inspection During Warranty Period
A. Mileage, 1000 Iniles or 30 days, whichever first occurs. Note: It is recornrnended that the first inspection at 1000 Iniles or 30 days consist of the following checks andadjustInents, because this will be the first opportunity the fore Inan will have to show the new custoIner the service facilities and to sell hiIn in the advantages ofInternationa1 Truck Service. B. Checks and adjustInents: 1. Distributor point gap. 2. Tighten cylinder head nuts uniforInly (all engine s). 3. Adjust valves (valve-in-head only). 4. Tighten Inanifold and carburetor flange nuts (all engines). 5. Check carburetor idle adjustInent. 6. Check oil pressure, generator charg ing rate, and heat indicator. 7. Check clutch pedal free InoveInent. 8. Change engine oil (charge for oil). 9. Lubricate chassis (charge, if it was forIner practice). 10. Check lubricant level in transInission and in differential. 11. Check riIn claInps, nuts, disc wheel studs and axle shaft studs and nuts. 12. Check brake pedal free InoveInent. 13. Check window regulator, windshield wiper, lights, and horn. 14. Short road test noting general perforIn ance and handling. B. Che cks and adjustInents: 1. Check spark plug gaps -- adjust if necessary. 2. Check distributor point gaps -- adjust if necessary. 3. Check ignition tiIning -- correct if neces sary. 4. Tighten cylinder head. 5. Adjust valves (all engines).
6. Tighten Inanifold and carburetor flange

nuts uniforInly. 7. Check fan belt tension. 8. Check carburetor idle adjustInent. 9. Check cooling systeIn for leaks. 10. Check air cleaner -- clean and change oil in SUInP if necessary. 11. Clean fuel pUInp sediInent bowl (renew gasket). 12. Check engine for oil leaks. 13. Change engine oil (Charge for oil). (If condition of oil indicates necessity for new filter cartridge, notify custoIner). 14. Check oil pressure, charging rate, and heat indicator. 15. Check governor control. 16. Check clutch pedal free InoveInent. 17. Check brake pedal free znoveInent. 18. Check fluid level in Inaster cylinder. 19. Lubricate chassis {charge if it were forIner practice}. 20. Check lubricant in transInlssion and differential (charge for grease, if added). 21. Check riIn claInp nuts, disc wheel nuts and studs and axle shaft nuts. 22. Check battery water level, cables and znountings. 23. Check window regulators, windshield wipers, lights, and horn. 24. Make a short road test noting general perforInance and handling -- Inake necessary adjustInents.
n.
Final Inspection During Warranty Period
A. Mileage 4000 to 4500 !niles or within 90 days. Note: This final inspection is recOluznended in order to give the truck a thorough check before expiration of warranty. and to enable the foreInan to sell the custoIner on the iInportance of preventative Inaintenance during life of truck.
PRINTED iN UNITED STATES OF AMERICA
L-UNE MOTOR TRUCK SERV1CE MANUAL
COLD WEATHER RECOMMENDATIONS

Important
There are a few simple precautionary measures which should be taken in preparation of a truck for cold weather operation. Instructions should be given truck owners covering this procedure. Note: High viscosity oils are available which also have very good cold-pour characteristics. 2.
Electrical
(a) Clean and adjust spark plugs. "Electrical System.") (See
1. Engine
Selection of proper engine lubricating oil de mands consideration of two important factors - namely, easy starting during low atmospheric temperatures, and adequate engine lubrication after the engine is placed in service. Lighter viscosity oils facilitate cold-weather starting and als 0 provide better immediate lubrication as the engine starts. They do not, however, provide adequate lubrication under sustained higher engine speeds or severe service. Increased oil consumption can also be expected when using lighter viscosity oils. Consideration must therefore be accorded the cold weather housing facilities for the idle truck, the service in which the truck is engaged, and the selection of higher viscosity oils which have better free-pouring characteristics at low temperatures.
(b) Check all wiring for loose or broken connections. Make necessary replace ments. (c) Clean and tighten battery cable terminals. (d) Check battery for being fully charged and electrolyte to star level in cell covers. (Note: During cold weather, the battery must not be allowed to stand after adding distilled water without running engine to charge battery. This is important because otherwise the water will not be thoroughly mixed with the electrolyte, and freezing may result.) (e) On models having an adjustable third brush generator, the charging rate should be adjusted to meet the demands of the cold weather operation.
In consideration of the foregoing, the following general recommendations are made:

MODERATE SERVICE (Trucks operating in multi- stop or other service where sustained higher engine speeds will not be encountered.) 90 0 (F.) ENGINE SD BD RD R-6602 and up ,~ TEMPERA TURES 32 0 (F.) HOO(F.) to 90 0 (F.) to 32 0 (F.) SAE-20W SAE-20W SAE-20W SAE-20W
3. Cooling System
(a) Drain and flush cooling system to remove all sediment and foreign material. (Note: The "reverse flushing" system is the most effective method and can be performed either in your own service station or by reputable radiator repair shops.) (b) Anti-freeze solutions of known value and manufacture only should be used. Specific gravity checks should be made periodically to assure protection from freezing. (Note: Salts or chlorides, sugar, glucose, honey, fats, etc., should not be used as an anti-freeze.) Where anti-freeze solutions are not used and cooling system is to be drained, you are cautioned to refer to instruction books for location of drain cocks or plugs on engine blocks, radiators, or oil coolers. (c) If the thermostat has been removed from the engine, it should be reinstalled after ascertaining that it is in good operating condition.
-IOO(F.) to +IOO(F.) SAE-IOW SAE-IOW SAE-IOW SAE-IOW
SAE-30 SAE-30 SAE-40 SAE-40 SAE-40 SAE-40 SAE-40 SAE-40
':'See Hot Climate - High Speed Instructions, see below For temperatures lower than minus 100(F.), use SAE-IOW plus kerosene. (SAE-IOW may be safely diluted with colorless kerosene up to 30%). Mix kerosene thoroughly with the oil before adding to the engine.
Hot Climate - High Speed.

For trucks operating on highway or other ser vices demanding sustained higher engine speeds use engine lubricating oils having a viscosity of as near SAE-50 as possible (SAE-40 for SD Engines) in keeping with the starting ability.

4. Winter Fronts
The use of an efficient winter front will enable the operator to better control the operating temperature. It will als 0 result in higher under-hood tempera tures, effecting more efficient operation of the engine, and will make it less sus c eptible to sludge formation and condensation.
and differ ential. A lubricant of lighter viscosity will provide better lubrication to the moving parts and will create less friction and resistance to the movement of the various gears, shafts, etc.
6. Propeller Shaft Bearing (not 6-wheel units)

The propeller shaft center bearing on Inter national trucks should be lubricated with a medium short fibre wheel bearing grease having the following characteristics: cold milled, sodium-soap content, having a work penetration consistency of 250 that will not break down below 300.
5. Rear Axle and Transmission

Severe cold weather may make a change of lubricant advisable in the transmission
BALL AND ROLLER BEARING MAINTENANCE
Important
In order to assure bearings being free of rust, dirt, or damage, the following procedure relative to storage, handling, and installation is recom mended: (b) Handle bearings carefully. Rough handling will damage containers and permit dirt and foreign matter to enter bearing.
3.
Cleansing and Lubrication of Bearings

(a) Use clean kerosene or Stoddard Solvent in a clean container. (b) Use clean rags or towels, and never use waste. Lint from waste may enter bearing. (Note: Suitable wheel bearing cleaner equipment is available, which will facilitate bearing cleansing.) (c) Dip bearing in kerosene several times, rocking bearing race rings slowly to dislodge grease from ball sockets. (d) Spin bearing while repeatedly dipping into kerosene. Continue operation until bearing runs smoothly and quietly or until it is clean and ready for inspection. (e) If bearing is found satisfactory, dip in a neutral oil or thin grease and wrap. (Note: Suitable wheel bearing grease packer equipment is available, which will produce excellent results.)
1. Storage
(a) Stock only limited quantity of bearings. Bearings should be ordered and stocked in quantities in keeping with requirements consistent with Branch Zone Repair Orders. This will assure fresh stock and will guard against obsolescence. (b) Store ball and roller bearings in their original wrappers or cartons. Do not remove protective coverings until ready to use the bearing. . (c) If necessary to inspect bearings in stock, they should be again carefully wrapped to guard against dirt. (d) Bearings which have been allowed to remain unwrapped must be washed, relubricated, and rewrapped. This does not apply to prelubricated bearings. (e) Store bearings in a cool and dry place. A hot storage space will cause the pro tective lubricant to melt and drain off the bearings. A damp storage space will permit moisture to collect on the bearings, resulting in rust and corrosion. Water or moisture will ruin a bearing.
4. Removal and Installation of Bearings

(a) Shafts or housings must be clean and free from burrs.
(b) Use properly arranged press plates or
2. Delivery of Bearings to Customer or to Service Station.

(a) Deliver bearings in original cartons or wrappers.
PRINTED iN UNI'tD STATES OF AMERICA
arbors for installation or removal of bearings. In pressing bearings into place the pressure or load should be so applied
GENERAL
Section Page 10

that it will not be transferred through the balls. For example, if bearing is applied to or removed from shaft, pressure should be applied to inner bearing cone.
If bearing is being installed in or re moved from a housing or case bore, pres sure should be applied to outer bearing cup.
and then proceed with operation. A bearing started in a cocked position will bind. Burrs in housings or on shafts will caus e severe binding and sticking. Bearing should rest squarely against shoulder or in recess. (g) Bearing should roll freely after in stallation unless individual specifica tions call for a preload. Te st bearing for bind or drag by holding bearing outer race between thumb and finger, and test for side play. (A radial clear ance of .0001" will produce side play of approximately .005" to .006".) Shafts mounted in bearings should rotate freely after installation unless in dividual specifications call for a pre load. Test by revolving shaft assembly.
(c) Do not hammer on bearings. Lead or babbitt hammers may chip off and allow pieces to lodge in bearing. Wooden hammers may leave splinters in bear ings. Steel hammers will chip, crack, or Brinell the bearing. (d) If necessary to heat bearing for instal lation or removal, use a light or 0 medium-weight oil heated to 225 (F .). Allow bearing to stand in this oil until thoroughly heated. (e) Upon installation of bearing, lubricate bearing seat with light oil. (f) Apply steady pressure. If bearing sticks or binds, ascertain cause. Correct fault
5. Intermixing of Component parts -- Roller Bearings

Wherever possible, intermixing of roller bearing component parts should be discouraged. Therefore, where possible, IH parts should be used to service IH assemblies, Tirnken parts to service Tirnken assemblies, etc.
STEEL AND ITS HEAT TREATMENT

To the average man, steel means but little more than something hard, heavy, and strong, and capable of being formed into practically any de sired shape. This is quite true as far as it goes. However, there are many conditions that deter mine and control the degree of hardness and of strength. attention must be given to its requirements in the finished part, and in the completed mechanism in operation. The most commonly known and used steels contain in addition to their ferrite or pure iron base either one or more of the follow ing elements -- carbon (the most important), nickel, chromium, vanadium, molybdenum, and tungsten, each being included either separately or combined with others in order to impart the distinctive properties of the included elements. It should be noted that upwards of 95 percent of all steel is pure iron. Castings, either grey iron, malleable iron or steel, originate with pure iron as their base.
In the manufacture of steels, the inclusion, in varying previously determined percentages of these elements, results in, with the proper heat treatment, definite closely predetermined physical properties. For example, one effect of chromium in steel is to increase its hardening power.
It is the object of this discussion to tell in non technical terms as nearly as possible just how and what these determining and controlling fac tors are, how they are applied, and the results accomplished thereby.
In automotive manufacture it is absolutely es sential that the very best steels available be used, and in their respective classes. One part will require extreme hardness to resist ab rasion or wear, another will require extreme toughness to resist shock and vibration, and to support heavy loads, another must develop great powers of flexibility, yet must resist bending, etc. In these various uses, the parts are subjected to different kinds of stresses, both "static" and "dynamic" (dead quiet and vibratory, respec tively) in combination with their loads carried under compression or in tension, or subjected to transverse, shearing or torsional stresses.
Before selecting a steel for a given purpose,
A steel rendered hard by the presence of chrom ium is far less brittle than one rendered hard by the presence of carbon alone. Hence, hardness combined with toughness may be secured by reducing the carbon and increasing the chromium content. However, chromium alone (or any other alloy) in the absence of carbon has no hardening power. The presence of both nickel and chrom

ium in steel makes it highly resilient and ductile and gives it greater hardness and better wearing qualities than plain carbon steel. Nickel chromium steels are especially valuable for parts to be hardened and tempered, as the finer structure thus produced has greater shock-resisting power than that of plain carbon steels. These are all valuable elements and there are doubtless many others equally as valuable as yet undiscovered. The presence of phosphorus and sulphur is in jurious to steel and must be guarded against. These impurities unite with other elements and form compounds which render the steel ex tremely brittle and liable to break. Phosphorus and sulphur inclusions are guarded against by their removal during manufacture, and by the inclusion of other elements which unite with these impurities to form harmless compounds, thus counteracting their bad effects. The hardening power of steel rests almost en tirely with its carbon content. As for example, a steel containing a 0.40 to 0.50 percent carbon (4/10 to 5/10 of I percent) is capable of be com ing much harder than one containing 0.10 to 0.20 percent. The carbon content is often re ferred to as forty or fifty points carbon, a point being equivalent to 1/100 of 1 percent. The heat treatment of steel consists of annealing, hardening and tempering.
GENERAL
Section Page 11
By critical range is meant the range above and between the critical heating point, or point of "decalescence, " and the critical cooling point, or point of "recalescence." The presence of these critical points in the heating and cooling of steel is a phenomenon and is explained as follows: While heating, the steel uniformly absorbs heat. Up to the decalescence point all of the energy of the heat is exerted in raising the temperature of the steel. At this point the heat taken in by the steel is expended, not in raising the temperature of the steel, but in work which produces the internal changes here taking place, the dissolving of the carbon in the iron. Therefore, when the heat is exhausted in this manner, the temperature of the piece. having nothing to increase it, will remain unchanged for a time, or may even fall slightly, owing to surface radiation, after which it will again increase. When the piece has been heated above the de calescence point, and is allowed to cool slowly, the process is reversed. Heat is then radiated from the piece. Until the recalescence point is reached the temperature falls. At this point al so the structure of the steel undergoes a change, the carbon crystallizes out of the iron, and the energy previously absorbed is converted into heat. This heat set free in the steel supplies, for the mement, the equivalent of that being radiated from the surface, and the temperature of the piece ceases to fall, remaining stationary, and should the heat resulting from the internal changes be greater than that of surface radiation, the resulting temperature of the piece will not only cease falling, but will actually rise slightly at this point. In either event the condition exists only momentarily and when the carbon and iron constituents have resumed their original re lation, the internal heat decreases, and the temperature of the piece falls steadily, due to surface radiation. From the foregoing, it is evident that there is a definite temperature at which any steel should be hardened, and that that temperature is de pendent upon or governed by the percentage of carbon in the steel; also, that a great loss occurs of both labor and material unless the hardening is carried out at that temperature. Of greatest importance is the necessity of rigid inspection ana tests to assure properly heat-treated parts. These critical points are determined and the temperature controlled by the use of recording pyrometers and other apparatus. The recording pyrometer presents graphically a temperature curve showing the exact temperature of the decalescence and recalescence points, the de calescence point being recorded on the chart while the piece being tested is in the furnace. and the recalescence point being recorded after removal of the piece from the furnace and in
Annealing
Annealing consists of heating above the "critical range," then cooling slowly, for the purpose of refining the grain, softening the steel to machin ability and relieving the internal strains set up in the steel by forging and hammering, these strains sometimes amounting to several thousand pounds per square inch.
Hardening
Hardening consists of heating above the critical range and cooling quickly, as by quenching in oil or water, the degree of hardness depending upon the carbon content of the steel and the severity of the quench.
Tempering
Water quenching is more severe than oil quench ing and is frequently followed by tempering or :irawing to reduce the brittleness imparted by the severity of the quench, this brittleness being ever attendant to the high degree of hardness thus obtained. The tempering heat must not rise above the ::ritical range, or the effects of the previous heat ;reatment will be destroyed and the refined :rystalline structure will be obliterated, be ::oming more coarse and suffering a considerable loss of hardness.
P~INTO
IN UNITED STATES 01'" AMEf'llCA

The elastic limit in pounds per square inch. The tensile strength in pounds per square inch. The percentage elongation.
the process of quenching. In obtaining these records the thermo-couple, or the furnace end of the pyrometer, is securely clamped to the test piece to insure that the reading will be that of the temperature of the test piece and not that of the atmosphere of the furnace.
Casehardening or Carburizing
The percentage reduction of area, Carburizing, carbonizing or casehardening are names applied to the process wherein a piece of low-carbon steel is packed in a carbonaceous material such as bone or leather, or a com mercial carburizing material and heated for a number of hours, just above the "critical range" of the steel, or above its point of decalescence, thereby causing the low-carbon steel to absorb carbon on the outer surface for a depth directly dependent upon the number of hours it is heated. Under such conditions, a carbonized case is pro duced which is capable of responding to ordinary hardening or tempering operations. The object of casehardening is the production of a hard wearing surface with a backing or core of tough, low-carbon steel. There are two results gained by its use, the first of which is the pro duction of the part from more easily machined steel of cheaper grade; and second, the pro duction of the part from a cheaper steel which is superior to a part produced from high-carbon steel, high enough in carbon to have the proper surface hardness, in that the casehardened sur face has the hardness to resist wear, backed by a low-carbon core which has the toughness to re sist shock, two factors of vital importance in the manufacture of motor truck parts, such as piston pins, camshafts, gears, etc. Upon receipt of each shipment of steel from the steel mills, a representative number of specimens are prepared for chemical analysis and for tests for physical properties. All steels must meet the r equir ements of the standards for their respective classes, both as to chemical analysis and physical properties, as specified by the Society of Automotive Engineers, both before and after heat treatment. The inspection and tests from the rough stock are precautionary measures to prevent defective material from getting into production, from which it would be impossible to obtain the proper results by heat treatment. The inspection and tests made on parts after having been machined and heat-treated are for the direct protection of the quality of the product. The most generally used tests, standardized and authorized by the S. A. E., are the Brinell hardness test, the Shore Scleroscope hardness test, and the Tensile test. The Brinell and Shore tests are check tests and for hardness only, while the Tensile test gives a complete history of the physical properties of the specimen tested as follows: Modulus of elasticity.
Brinell Test
The Brinell test is commonly made with a hydraulic testing machine in which a steel ball of ten millimeter diameter is pressed into the test piece by a load of three thousand kilograms. The diameter of the impression the ball pro duces in the test piece is then measured and checked against a standard. Thus an impression four millimeters in diameter indicates softer steel than a diameter of thr:ee and one-half millimeter s. The Brinell test is definitely related to the ul timate strength of the material.
Scleroscope Test
The Shore Scleroscope test is made with a small instrument which drops a diamond-tipped ham mer approximately ten inches through a small glas s tube upon a smooth surface of the steel to be tested, and the height of the rebound of the hammer measured against a scale at the back of the glass tube. Hard steel is taken as being 100 hard on the Scleroscope and soft steel approximately 30 to 35 hard. Thus the higher the rebound, the harder the steel. After noting the remarks on the Tensile test, it will be seen readily that the Brinell and Scleroscope tests are excellent methods of check-testing rapid ly and accurately, finished and serp.i-finished parts that it would be impractical to test other wise. The resulting values obtained by means of the Tensile test are invaluable in both the de signing and testing engineers. The designer must take into consideration the load that the part will be required to carry, the function it must perform, and the nature of the stress to which it will be subjected. The weight of the part must be held to a minimum, and the steel selected must be one capable of withstand ing these stresses, at the same time maintain ing a wide margin of safety. A very rigid inspection must be maintained on parts subject to shock and vibration, as tool marks and scratches, under-cut radii, or sharp corners, are frequently the cause of early fail ures of properly designed and heat-treated parts such as axles, jackshafts, steering knuckles, etc.
Tensile Test
It is a comparatively easy matter to check up
L-LINE MOTOR TRUCK SERViCE MANUAL

on machined parts with gauges and measuring instruments, as the defects and imperfections are generally more or less visible. However, checking up on heat treatments is an entirely different proposition. The Tensile test is the most accurate and most approved method, and is made as follows: A test bar of the standard S. A. E. form is machined from the material to be tested, and is held in threaded grips in a vertical position in the testing machine. The machine is set in motion and the test bar is slowly stretched until ~t is br oken. The point at which the elongation ceases to be proportional to the load is desig~ated as the elastic limit. This is the highest point at which, if the load were removecl., the bar would resume its original length. This is also the point at which, if exceeded, failure of the part commences. The weight of the load at this point is read on the weighing beam of the testing machine and converted into pounds per square inch, to be checked against S. A. E. specifications for that particular steel from which the test bar was made. The elastic limit point is determined by the use of an extensometer, a delicate instrument which shows the amount the test bar stretches, and is capable of measuring to the ten-thousandth part of an inch. While noting the elastic limit the test continues, and the ultimate tensile strength is noted. This is the greatest load the bar will withstand before it breaks. From this point on to the breaking point, the bar fails rapidly. After breaking, the bar is measured to determine the total elongation and the reduction in area of cross section, and these two values are con verted to percent of the original bar dimensions. Research work is constantly being carried on in the chemical and physical laboratories to pro duce better materials and better methods of heat treating; and many special tests are devised, such as torsion tests, fatigue tests, impact tests, and vibratory tests. The qualities of designs and their manufacture are frequently proved and checked by tests that approximate as nearly as possible the actual working conditions of the parts.
by the microscope, all metals have a crystalline structure: the fibrous structure was caused by segregations or inclusions of non-metallic impurities (example: slag in wrought iron). Microscopic examination of steel under stress shows no change of the general scheme of in ternal structure, but under sufficiently severe stress, there appears a gradual breakdown of the crystals in the structure. This manner of failure is rightly termed a "fatigue failure."
If the fractured surface of a fatigue failure is carefully examined, it is usually seen to be made up of two parts; that is, it appears to have two different-size crystalline structures -- (1) near the extreme outside of the fractured sur face it appears dark, dull, and lusterless, with a poorly defined crystalline structure: while the appearance (2) at and immediately surrounding the center of the break is bright and shows a definite crystalline formation. This appearance is caused by the method and nature of the fail ure, and in that the (1) outside of the fractured surface was caused very slowly and has started from many centers and due to the constant vi bration and rubbing together of the two faces of the fracture, the sharp corners of the crystals become worn and smooth; whereas the break at the center and immediately surrounding (2) was suddenly torn in two on the natural surfaces of cleavage with no subsequent vibration or rubbing, thus leaving exposed the original struc ture of the steel.
Cause of Fatigue Failure

The cause of a fatigue failure may be attributed to a repetition of stresses which exceed the elastic limit of the steel. This may be sub divided as follows:
Manufacturer's Responsibility
1. 2. 3. 4. Defective raw material. Defective heat treatment. Defective design. Defective machining.
Fatigue Failures
A fatigue failure of a shaft or axle is charac terized by suddenness, lack of warning, apparent brittleness of material, and, in many cases, a fracture with a crystalline appearance over a part of its surface. This crystalline appearance led to the old theory that under repeated stress steel "crystallized in service," changing from a ductile "fibrous" structure to a brittle "crystalline" one. This theory, however, has been quite thoroughly de molished as a result of study of the structure of steel under the microscope. As revealed
h~INTEO
Truck Operator's Responsibility

1.
2. 3. 4. Overloading. Overspeeding. Rough handling and dr iving. Road conditions.
Hardness is that property of a material by virtue of which it resists penetration. Toughness is that property of a material by virtue of which it resists shock and vibration.
IN UNITED STATES OF AMERICA

wards treated, to develop in them a high degree of strength, and is one of the best carbonizing steels obtainable. Following is the chemical analysis and the physical properties to cor respond to a Brinell hardness of 275 or an approximate Shore hardness of 40:
Transmission and differential gears must have hard surfaces and tough cores or centers. They are designed with a 20-degree tooth pressure angle, which causes the teeth to roll together and apart, rather than to slide together and apart from each other, as do gears whose teeth have differ ent angle s; thus gear tooth wear is mini mized, both by heat treatment and design. Some common causes for gear failures of inferior manufacture are as follows: 1. Lack of hardness, battering and shearing, soft cores. 2. Excessive hardness and attendant brittle ness, chipping. 3. Thin "case" and soft core, cracking, and chipping. 4. Case too deep, no tough backing to resist shock. Extreme care is given the inspection of gears, both as to machined dimensions and heat-treated conditions. Test gears are broken and the structures examined, depth of "case" noted and held to approximately 3/64 - inch deep. They must not batter at corners, and they must not chip. They are hardness-tested by Scleroscope method.
One steel used in making transmission and differential gears is designated by the S.A.E. No. 3120; it is an ideal steel for the manufacture of all parts which are drop-forged and after

Chemical Analysis
Carbon .0.15 to 0.25% Nickel .1.00 to 1.50"/0 Phosphorus Below 0.04% Sulphur Below 0.045 % Chromium .0.45 to 0.75% Manganese 0.50 to 0.90%
Physical Properties
Elastic limit, lbs. per sq. in. Tensile strength, lbs. per sq. in Elongation in 2 in percent Reduction of area Brinell hardness numeral Shore hardness numeral 120,000 160,000 15.00 52.50 275 40
The chemical analysis and physical properties shown above are those that will be retained by the core or the centers of the gears after car burizing, and are the factors responsible for the toughness and fatigue resistance of the gears. The surfaces are hardened to 75-85 Scleroscope, to an approximate depth of 1/16 inch, this combination of surface hardness and center toughness being the ideal condition and insuring long gear life.
GLOSSARY OF TECHNICAL AND MECHANICAL TERMS

Addendum
That part of a tooth of a gear or of a screw thread between the pitch circle or line and the extreme point of the tooth or thread.
Altitude
The perpendicular distance between the bases, or between the vertex and the base of a solid or plane figure.
Allowance
Covers variation in dimensions to allow for different qualities of fits.
Angle
The difference in direction of two lines which meet or tend to meet. The lines ar e called sides, and the point of meeting, the vertex of the angle. They are measured by degrees and by radians. One degree is equivalent to the angle at the center of a circle, subtended by an arc whose length equals one three hundred sixtieth (1/360) of the circumference. One radian is equal to the angle at the center of a circle when subtended by an arc equal in length to the radius of the circle. One radian equals 57.2958 degrees, also 1 radian equals 180/11'. The Protractor is used for the measurement of angles. A right angle is one which is formed by the radius moving through 1/4 of the circurr" ference. It is a square angle and contains 90 0
Alloy Steel
A steel which owes its characteristic properties chiefly to the presence of one or more elements other than carbon; i.e., nickel, chromium, vanadium, molybdenum, etc.
Ampere
The practical unit of electrical current, the current produced by one volt acting through a resistance of one ohm.

An acute angle is one containing less than 90 0 An obtuse angle is one containing more than 90 0 An oblique angle may be any other than a right angle. A reflex angle is one containing more than 180, A helical angle is the angle of a thread at the pitch line, with the axis of a threaded part; the lead angle of a thr ead is the total or included angle between the sides or walls of a thread, measured on the axial line. A dihedral angle is one formed by the opening between two intersecting planes. The vertex of an angle is the point of inter section of the two lines which form the angle.
water one degree Centigrade. (1 great calorie 1000 small calories.)
Cantilever
A projecting beam, bar, or member supported at one end only.
Center of Gravity
That point in a body about which all the parts exactly balance each other.
Center of Oscillation
If a body oscillates about a horizontal axis which does not pass through its center of gravity, there will be a point on the line drawn from the center of gravity perpendicular to the axis, the motion of which will be the same as if the whole mass were concentrated at that point. This point is called the center of oscillation.
Annealing
See Heat Treatment.
Austenite
See Metallography.
Center of Percussion
If a body oscillates about an axis then the point at which, if a blow is struck by the body, the percussive action is the same as if the whole mass of the body were concentrated at that point, is called the center of percussion. This point is located at the same point as the center of oscillation.
B ending Moment
A moment is equivalent to the product of a force multiplied by a distance, and is measured in inch pounds or foot-pounds. The bending moment at any cross section of a piece under flexure measures the tendency to cause flexural failure, and is equal in magnitude to the summation of the moments of the forces on one side of the cross section.
Center of Gyration
The center of gyration with reference to an axis is the point at which the entire weight of a body may be considered as concentrated, the moment of inertia, meanwhile, remaining un changed; or, in a revolving body, the center of gyration is the point at which the whole weight of the body may be considered as concentrated, the angular velocity remaining the same.
Brinell Test
A hardness-testing instrument, employing the hardened steel ball indentation method.
B.T.U.
Abbreviation for British Thermal Unit which represents the amount of heat required to raise the temperature of one pound of water one degree Fahrenheit at or near 37 0 F. There are 778 foot pounds of energy in a B.T.U. and 42.4 B. T.U. to one horsepower.
Centrifugal Force
When a body revolves in a curved path, it exerts a force called the centrifugal force upon the arm or cord which restrains it from moving in a straight (tangential) line.
Cor CL
Abbreviation for center line.
Calibrate
To ascertain the accuracy of and to rectify same, as regards a precision measuring instru ment, etc.
C. G. S.
An abbreviation for the Centimeter Gram Second or Absolute System of units much employed in physical science, based upon the centimeter as the unit of length, the gram as the unit of weight, and the second as the unit of time.
Calorie
Any of several thermal units, as: (a) The amount of heat (small calorie) required to raise the temperature of one gram of water one degree Centigrade. (b) The amount of heat (large or great calorie) required to raise a kilogram of
PRINTED I"" Ut<.llTEO STATES OF'
A~RIC"
Cementite
See Metallography.
GENERAL
Section Page 16
LLINE MOTOR TRUCK SERVICE MANUAL

Dedendum
The dedendum of a gear tooth or of the tooth of a threaded part is the distance from the pitch circle to the root of the tooth or thread.
Chamfer
A bevel, or a corner or edge removed, a relief.
Coefficient of Friction
The force of friction, F bears -- according to the conditions under which sliding occurs -- a cer tain relation to the pressure between the bodies; this pressure is called the normal pressure, N. The relation between force of friction and nor mal pressure is given by the coefficient of friction, generally denoted by the Greek letter AA-. Thus: F
Deformation
The change of form of a member accompanying the application of external load. The term "strain" is used in this manual as synonymous with deformation. Deformations may be stretches under tension, compressions under compressive loads, deflections under bending (or flexure), twists under torsional moment, or detrusions under Twist is a special case of shearing detrusion. In the physical laboratory the de formation per unit of length over any gauge length on a specimen is called the unit defor mation, or unit strain.
JiXN, andA.i :;:F

N
Cold Bending
See Cold Working.
Cold-Drawn Steel
See Cold Working.
Drawing
See Heat Treatment.
Cold-Rolled Steel
See Cold Working.
Ductility
Ability to withstand stretch without rupture. Ductility is usually measured by the percentage of elongation, after rupture over a gauge length laid off on a specimen before stretching, or by the reduction of area of the original cross section of a specimen when tested in tension.
Cold Working
Changing the shape of steel parts by compressing, stretching, bending, or twisting, using stresses beyond the yield point and temperatures below the critical range. Cold-drawn steel is finished by being drawn through a die, while cold-rolled steel is finished between rollers.
Contour
Outline or profile of an object.
Dynamic Balance
A crankshaft may be in perfect static balance, but if it is mounted in bearings and revolved at high speed great vibration may develop which would soon cause failure of engine bearings and possibly cause breakage of the shaft itself due to fatigue action. Dynamic unbalance means that the weight sums of diagonally opposite portions are not equal. Take, for example, a pulley that is in perfect balance. Visualize the pulley mounted on a shaft supported by bearings. Attach a weight to the outer periphery on one edge.of the pulley, then attach an exact counterweight to the opposite side of the pulley on the opposite edge. The pulley continues to be in static balance as evidenced by the fact that it turns freely and stops with the counterweights either up, down, or in any other position; but if the pulley is re volved at a high rate of speed its dynamically unbalanced condition will be very much evidenced by the vibration. This dynamic unbalance is eliminated in a crankshaft first by determination of the heavy points and next by drilling into these points until the necessary amount of metal and weight has been removed.
Critical Range
See Metallography
Crystal
See Metallography.
Cycle
Applied to the internal-combustion, four-cycle engine, a cycle comprises four strokes for each piston (1, intake; 2, compression; 3, explosion; 4, exhaust) performed during two revolutions of the crankshaft. An interval or period of time occupied by one round or course of events, recurring in the same order in a series.
Decalescence
The sudden absorption of heat observed when metals in process of heating pass certain tem peratures.
GENERAL

Dyne
The force which acting on one gram for one second imparts to it a velocity of one centimeter per second, or approximately that force exerted by a one milligram weight under the influence of gravitation.
Section Page 17
Extensometer
An instrument for measuring small changes of length of specimens under tension; capable of measuring accurately to one ten-thousandth part of an inch.
Factor of Safety Elastic Limit

The term "elastic limit" is unfortunately used very loosely in general practice. In scientific usage the term is used to denote the highest unit stress at which material will completely recover its form after the stress is removed. Proportional elastic limit is used to denote the highest unit stress at which stress is pro portional to deformation. The values found for both the true elastic limit and the propor tional elastic limit are dependent upon the ac curacy of the apparatus used, and the precision with which stress strain diagrams are plotted. For practical purposes elastic limit and pro portional limit may be regarded as inter changeable terms. The yield point is that unit stress at which the material shows a sudden marked increase in the rate of deformation without increase in load. It is usually determined by the sudden drop in the balance beam of the testing machine, as strain is applied to the specimen at a uniform rate or by a sudden increase of deformation which can be seen by the use of a pair of dividers on the specimen. Working stresses should never exceed the elastic limit. They are generally based on the ultimate strength of the material. The ratio of the ultimate strength of a given material to the allowable working strength is called the "Factor of Safety." The factor of safety may be considered as the product of four primary factors which may be designated as factors a, b, c, and d, designating the factor of safety by F. F=axbxcxd The first of these factors (a) is the ratio of the ultimate strength of the material to the elastic limit, meaning in this case, by the elastic limit, that boundary line within which the material is perfectly elastic and takes no permanent set. For ordinary materials, the factor a ::: 2; for nickel steel and oil-tempered forgings, it is re duced to 1-1/2. The second factor (b) depends on the character of the stress within the material. This factor is 1 for a dead load; 2 for a load varying between zero and maximum; and 3 for a load which pro duces alternately a tension and a compression equal in amount. The third factor (c) depends upon the manner in which the load is applied to the piece under stress. For a load gradually applied the factor is 2. If the load is applied, not only suddenly but with impact, this factor must be still further increased in value. The last factor (d) may be called the factor of ignorance, or the "fool factor. II The other factors provide against known conditions and this pro vides against the unknown. It com.monly varies in value between 1-1/2 and 3 and occasionally should be given as high a value as 10. It pro vides against accidental overload, against un expectedly severe service and unreliable or imperfect materials, etc. When all the conditions are thoroughly known and there is no danger of overload, this factor may be made equal to l-l/Z for wrought iron and mild steel and 2 for cast iron. As an example of the use of the formula given for the factor of safety that should be usedAor an internal-combustion engine connecting rod, the elastic limit will probably be slightly more than one-half the ultimate strength, therefore, a::: 2. The rod will be alternately in tension and compression, therefore, b=3. The explosional
Elongation
See Ductility.
Endurance
In the physical laboratory this term is used to
denote the number of cycles of repeated stress withstood by a specimen before failure.
Endurance Limit
The highest unit stress which, applied in cycles of completely reversed stress, can be withstood an indefinite number of times without failure.
Endurance Strength
A general term denoting ability to resist re peated stress, synonymous with fatigue strength.
Erg
A theoretical unit of work or energy being the work done by one dyne working through a distance of one centimeter.
PRINTED IN UNiTED STATES OF" AMEI1ICA
L-L1NE MOTOR TRUCK SERVICE MANUAL

have to slide constantly on one another, without turning. RUNNING FIT -- For parts which in functioning have to revolve constantly one in the other, at a medium speed and with very little play. EASY RUNNING FIT -- Parts revolving with a relatively large amount of play,
force will be applied suddenly, therefore, c=Z. The material is very reliable, therefore, d=l-l/Z. Then F = 2 x 3 x 2 x 1 -1/2 = 18.
Fatigue of Metals
The action which takes place in metals causing failure after a large number of applications of stress. Fatigue failures are characterized by their suddenness and by the absence of general deformation in the piece which fails. A wire broken by bending backward and forward is a characteristic fatigue failure.
Fillet
A narrow band of material, frequently in shop practice used to designate a radius on a shaft or other part.
Ferrite
Pure metallic iron, in the sense here used, entirely free from carbon inclusion.
Flute
The groove cut in taps and reamers to form the cutting edge and allow room for chips.
Fibre Stress or Fiber Stresses

This is the stress in the extreme fiber, or the maxim um stress in the cross section con sidered, due to the application of the load. Fibre stresses with a cantilever would denote ten sion in the upper fibers and compression in the lower ones, with a neutral plane between. With a beam supported at both ends, the fiber stress would be the reverse of that in a canti lever. Thus a fibre stress of 50,000 pounds per square inch at point of stress on a cantilever loaded at the free end would denote the maximum stress to which the cantilever was subjected.
Friction
Is the resistance to motion which takes place when one body is moved upon another, and is generally defined as "That force which acts between two bodies at their surface of contact, so as to resist their sliding on each other."
Gauge or Gage
Master, Standard or Reference; terms applying to a nearly perfect gauge used for calibration of working gauges.
Gauge -- Limit
A gauge having two sizoes, the difference be tween them representing the tolerance or allow able variation. One size must go into or over the work being checked, and the other size must not go. These gauges are frequently referred to in shop practice as "tolerance gauges" and as "go" and "no go" gauges.
Fit
The different classes of fit of shafts in their holes most generally used are as follows: SHRINK FIT -- For parts which have to be fitted together by means of an application of heat to expand the hole, at which time the shaft is in serted. On cooling the hole contracts, making a perfect union which requires no keys or other anchors of any kind. The bores are always machined to a smaller diameter than that of the shaft. FORCE FIT -- For parts which have to be fitted together by means of a press; they must be keyed if they are to be subjected to a twisting force. DRIVING FIT -- For parts which have to be fitted together with a lead hammer, but which can be afterwards disassembled. PUSH FIT -- For parts which have to be fitted together by hand without special force, and without having perceptible shake when assembled, they should remain motionless in each other. SLIDING FIT -- For all parts which in functioning
Gear Tooth Parts

PITCH DIAMETER--PITCH CIRCLE: When one of two gears that are in mesh with each other are revolved, it will drive the other gear at a certain rate of speed. Imagine that, as well as the two gears, two discs without teeth are also in contact, so that when one disc is revolved it will drive the other disc by frictional force. The diameters of the discs may be so selected that when one revolves at the same rate as the gear to which it corresponds, it will drive the other disc at the same rate as the second gear is driven. The diameters of the discs are then the same as the pitch diameters of the gears, and the circumferences of these discs represent the pitch cir cle s of the gear s. The outside diameter of a gear is the diameter measured over the top of the teeth.

The root diameter of a gear is the diameter measured at the bottom or roots of the teeth. The center distance is the distance between the centers of two meshing gears, the pitch circles of which are tangent to each other. The diametral pitch of a gear is the number of te eth for each inch of pitch diameter, and is found by dividing the number of teeth by the pitch diameter. Bastard gear teeth are sometimes generated for special purposes, having their teeth of different pitches with regards to width and depth. Example, a gear of 6/8 pitch the teeth correspond in width or thickne s s to 6 pitch, and in depth tQ 8 pitch. The circular pitch is the distance from the center of one tooth to the center of the next, measured as an arc along the pitch circle. The chordal pitch is the distance (on the pitch line) from the center of one tooth to the center of the next, measured along a straight line. The thickness of a gear tooth is generally under stood to be the thickness at the pitch circle, measured along the circular arc. The chordal thickness of a tooth is the thickness at the pitch circle measured along a straight line or as a chord. The addendum of a gear tooth is the distance from the pitch circle to the top of the tooth. The dedendum of a gear tooth is the distance from the pitch circle to the root of the tooth. The working depth is the depth to which the teeth in a meshing gear enter into the spaces between the teeth of the opposing gear. The clearance is the amount by which the tooth space is cut deeper than the working depth. The face of the tooth is that part of the tooth curve that is between the outside circumference and the pitch circle. The flank of the tooth is that part of the working depth of the tooth which comes inside of the pitch circle. degrees latitude and sea level.)
Grain
See Metallography.
Hardness
Is that property of a material by virtue of which it resists penetration. The two common tests for hardness are the Brinell test and the Sclero scope test. In the Brinell test a hardened steel ball of a standard diameter is forced against the surface of a test specimen, using a standard pressure. The diameter or the depth of the resulting impression is an inverse measure of the hardness. In the Scleroscope test a small weight fitted with a diamond point is allowed to fall from a standard height upon the surface of the specimen, thus causing a minute indentation. The height of rebound is a measure of the hard ness.
Heat-Treatment
HEAT-TREATMENT of steel is the proper con trol of heating and cooling so as to produce the desired struction, pearlite, sorbite, troostite, martensite, or austenite, and includes: ANNEALING, which consists of a very slow cooling from above the critical range and which gives a large-grained, soft pearlitic structure. NORMALIZING, which consists in cooling from above critical range in still air and which gives a fine-grained, pearlitic structure. OIL-QUENCHING, which consists in cooling from above the critical range by cooling in oil at room temperature and which yields steel of sorbitic or troostitic structures, depending on the carbon content (certain special alloy steels yield a rnartensitic structure or even an austenitic structure with oil-quenching). WATER-QUENCHING, which consists in cooling from above "he critical range by cooling in water at room temperature and which yields steel of martensitic, troostitic or sorbitic structure, depending on the carbon content (certain special alloy steels yield a martensitic or austenitic structure with water-quenching). DRAWING, which consists in reheating quenched steel to a temperature slightly below the critical range and cooling. This process tends to bring martensitic, troostitic or sorbitic steel towards the pearlitic state, and, by varying the tempera ture of drawing both thermally and as to time, it is possible to control the state of the steel with an excellent degree of precision. Other liquids are sometimes used for quenching steel: such as molten lead, molten barium chloride, ice water, mercury, and brine.
Gravity
The attraction of bodies toward the center of the earth. Under the influence of gravity alone, all bodies fall to the earth with the same velocity and with the same acceleration. The acceleration increases with the latitude and decreases with the elevation above the level of the sea. Its value at the level of the sea in the latitude of New York is 32.16 feet per second. (In the metric system, Gravity = 9.81 meters per second at 45
PRINTED IN UNITED ST.4.TES OF AMERICA.
GENERAL
Section Page 20

dissipated as heat. This dissipated energy is called "mechanical hysteresis,"
Alloying elements, including carbon, slow up the transition period so that high-carbon steels and alloy steels are more susceptible to heat treatment than are low-carbon steels. See Metallography.
Inch-Pounds
A term used to denote work or energy.
Helix
A spiral. A coiled spring or a screw thread forms a helix.
Inertia
See Mechanics.
High-Precision Work
This term generally applies to the manufacture of measuring instruments, magnetos, special machine tools, electrical instruments, automotive practice, etc., and generally for all kinds of apparatus for which the fits must be made with extreme accuracy and in which accordingly the interchangeability of the various parts must be uniform to a high degree.
Iron
See steel for distinction between iron and steel.
Joule
A unit of work or energy, approximately equal to .738 foot-pounds or .24 small calorie, or approximately the energy expended in one second by an electric current of one ampere in a re sistance of one ohm, is a joule.
Horsepower Land
See Mechanics. One of the sharpened ridges which make up the cutting section of a tap, die, reamer or milling cutter after the flutes or chip clearance spaces have been removed.
Hydraulics
The science dealing with liquids in motion.
Hydrostatics
The science of the pressure and equilibrium of liquids (incompressible fluids).
Lead
The longitudinal distance which a screw thread advances when turned one complete revolution.
Hyper -Eutectic Steel

Steel more highly carburized than eutectoid steel is called hyper-eutectoid, or hyper-eutectic steel, and therefore contains free cementite, i.e., high carbon steel.
Limit
A maximum or minimum dimension slightly above or below a standard size, not the distance between dimensions. See Tolerance.
Martensite -Martensitic
See Heat-Treatment; also Metallography.
Hypo-Eutectic or Eutectoid
Steel containing less than 0.85 to 0.90% Carbon and therefore some free ferrite is called hypo eutectoid or hypo-eutectic steel, i.e., low-carbon steel.
Mechanics
Is the science of applied mathematics which treats of the action and effect of forces on bodies. A force is defined as any cause tending to pro duce or modify motion. The units by which a force is usually measured are pounds or tons. Besides force there are two other elementary quantities in mechanics from which numerous compound quantities are derived. These are distance, measured in linear units as inches, feet, etc., and time, expressed in hours, minutes, or seconds. WORK, in mechanics, is the product of force by distance, and is expressed by a combination of units of weight (force), and distance, as inch pounds, foot-pounds, foot-tons, etc.
Hypoid
Hypoid: (contraction of the word hyperboloid) meaning that the piniQn is offset with respect to the center line of the ring gear.
Hysteresis -- Mechanical
If a load is applied to a specimen, and is re moved, then, if the specimen is perfectly elastic under the stress caused by the load, the energy expended in loading the specimen is all given back when the load is removed. If the specimen is not perfectly elastic under the stress caused by the load, then some of the energy applied is

POWER, in mechanics, is the product of force by distance, divided by time, or the performance of a given amount of work in a given time and is expressed as inch-pounds per minute, foot pounds per minute or second, etc. The term "power" is frequently used by writers or mechanics to designate a force. In connection with the so-called "mechanical power" -- the lever, wheel and axle, wedge, screw, etc. -- it is usual to speak of the applied force as the power; this is, however, not strictly correct, as power should always, in mechanics, be used in ac cordance with the definition given above. HORSEPOWER (abbreviated H.P.) is the unit of power adopted for engineering work. One horsepower is equal to 33,000 foot-pounds per minute, or 550 foot-pounds per second. The metric horsepower is equal to 75 kilogram meters per second, or 542.5 foot-pounds per second, or 32,550 foot-pounds per minute. The kilowatt used in electrical work equals 1.34 horsepower; or one horsepower equals 0.746 kilowatt. VELOCITY is distance divided by time, and is expressed in feet per minute, miles per hour, etc. INERTIA is that property of a body which causes it to tend to continue in its present state of rest or motion, unless acted upon by some force.
formed, glvlng a very hard and brittle sub stance; troostite, in which dark-colored masses resembling sorbite are surrounded by a ground work of martensite, the troostitic state yielding a substance hard but tougher than the martensite; sorbite, in which cementite and ferrite are in a state resembling an emulsion, yielding a sub stance fairly hard and very tough; and pearlite, in which bands of ferrite and cementite exist, usually in stratified layers or bands.
1 the steel has a carbon content of about 0.900/0,

all the grains will be pearlite; if the carbon con tent is lower than 0.90% there will be grains of pearlite and grains of ferrite; if the carbon content is greater than about 0.9010 there will be grains of pearlite and grains of cementite. The presence of carbon or of other alloying elements slows down the process of transition. By varying the rate of quenching steel, the transition process may in general be halted at any desired state, and the resulting cooled steel may be given any desired characteristic structure. See Heat-Treatment, also Micro graph.
Micrographs
Are obtained by polishing the surface of a metal, etching the polished surface with a suitable reagent to bring out the metallographic structure, then repr oduc ing, usually by photographic methods, the appearance of the surface as seen through the microscope. Photomicrograph and microphotograph are terms sometimes used for micrographs made by a photographic process.
Metallography
Deals with the physical state and the proximate constituents of a metal or an alloy. It has to do with the physical grouping, distribution of con stituents and relative dimensions, of the sub stances as revealed by microscopic examination. It may be characterized as a study of the anatomy of metals. Steel is an alloy, the essential constituents of which are iron and carbon, the latter being the controlling element. The carbon exists in steel as a carbide of iron, Fe3C, to which the name cementite is applied. The free iron or ferrite, together with the cementite, has the power of forming a conglomerate called pearlite, a very intimate mechanical mixture composed of about 7 parts of ferrite to one part of cementite.
Mil, Circular
A circular mil is the area of a circle 0.001 inch in diameter and is a unit in the measurement of diameters and cross-sectional areas of electric wires.
Millivoltmeter
An electrical instrument for measuring small electric potentials. Used for measuring the small voltages of thermo-couples developed by changes of temperature. (See Pyrometer.)
Modulus of Elasticity
1 molten iron is cooled there is formed first a
solution of carbon in molten iron; then, as the metal solidifies, the carbon exists as cementite in solid solution in the iron. This solid solution is called austenite, and it crystallizes into im perfect crystals or grains. With further cooling the steel passes through a critical or transformation range of temperature (extreme range about 1650 0 F. to 1250 0 F.) and the two constituents of the metal pass successively through several transition stages, namely: martensite, in which long needle-like crystals are
PRINTD IN UNITED STATES Of' AMERIC'"
Is the quotient obtained by dividing the stress per squar e inch by the elongation in one inch caused by this stress. For all stresses below the elastic limit, the unit stress bears a constant ratio to the unit deformation.
Moment of a Force
The moment of a force with respect to a point is the product of the force multiplied by the perpendicular distance from the given point to the direction of the force. The perpendicular distance is called the lever arm of the force,
L-LINE MOTOR TRUCK SERVJCE MANUAL

equal reaction or, in other words, if a force acts to change the state of motion of a body, the body offers a resistance equal and directly opposite to the force.
The moment is the measure of the tendency of the force to produce rotation about the given point, which is termed the center of moments. Moments are expressed in inch-pounds, foot-pounds, etc., and are designated as clockwise or contraclock wise, according to their direction. The term torque is equivalent to the term moment.
Neutral Plane
See Fibre Stress.
Moment of Inertia
The moment of inertia of a body with respect to an axis is the sum of the products obtained by multiplying the weights of each elementary particle by the square of its distance from the axis. Therefore, the moment of inertia of the same body varies according to the position of the axis. It has its minimum value when the axis passes through the center of gravity. The moment of inertia is numerically equal to the weight of the body which if it could be conceived of as concentrated at a distance of unity from the axis of rotation, would, if actuated by the same forces, rotate with the same angular velocity as that of the actual body. In other words, the moment of inertia bears the same relation to angular acceleration as weight does to linear acceleration. When the term "moment of inertia" is used in regard to areas, it is equal to the sum of the products obtained by multi plying each elementary area by the square of its distance from the axis. The moments of inertia of surfaces are especially useful in cal culating the strength of beams.
Nonferrous Metals
Metals in which iron is not a constituent.
Ohm
The practical unit of electrical resistance, being the resistance of a circuit in which a potential difference of one volt produces a current of one ampere.
Pearlite
See Metallography.
PhysiCS
The science of phenomena of inanimate matter in
volving no chemical changes, comprising me
chanics, magnetism, electricity, light, heat, and
sound.
Pi-i
The 16th letter of the Greek Alphabet, corre

sponding to the English P, is used as a constant
to denote the ratio (3.14159+) of the circum
ference of a circle to its diameter.
Momentum
The momentum of a moving body is the intensity of that constant force which, resisting its move ment, would bring it to rest in one second. Momentum ::: mass X velocity in feet per second. _ igh Momentum w_e......... _t X ve l ' t ' l l f ee t per second 32.i6 OCl y i Momenturn should not be confused with the rnoment of a force, defined above.
Pitch, Diametral, Circular

See Gear Tooth Parts
Pitch Diameter
See Gear Tooth Parts.
Pneumatics
That branch of physics treating of the rnechanical properties of air and other gases, as of their weight, pressure, elasticity, etc.
Motion, Newton's Three Laws

1ST LAW: Every body continues in a state of rest of uniform motion in a straight line, except if it is acted upon by a force to change its state of rnotion or rest. 2ND LAW: If a body is acted upon by several forces, it is acted upon by each of these as if the others did not exist. This is true whether the body is at rest or in motion. In other words, if two or more forces act upon a body at the same time, each produces exactly the same effect as if it acted alone; the total effect or resultant rnotion of all the forces may be found by a dia gram in the same way as the resultant of forces is found. 3RD LAW: To every action there is always an
pound-Inches-Feet
See Moments of a Force; Mechanics, etc.
Power
See Mechanics.
Prony Brake
See Horsepower.
Pyrometer
An instrument for measuring high temperatures.
Briefly, one type of pyrometer (that in use by International Harvester) is of the Thermo electric type, which utilizes the electromotive force generated by a junction of two dissimilar

metals when exposed to heat. In each pyrometer the rea r e two junctions made by welding to gether wires of two dissimilar metals, platinum and platinum-rhodium; for example, one junction is then exposed to the temperature to be measured and is called the "hot junction"; the other junction, which is opposed to the first named junction, is kept at a constant temperature and is called the "cold junction." A mill voltmeter for measuring electromotive force is attached by conductors to the free ends of the opposed junctions and by its reading indicates. the electromotive force generated and hence the temperature of the "hot junction...
metal with a carbon content les s than about 1.7%, which is made by a process involving complete fusion. Wrought iron has a low carbon content, and is made from a pasty mass at a temperature below complete fusion. Ferrous metals with carbon content higher than about 1.7% are called "cast iron."
stress
An internal force which resists the destructive action of external force. Stresses are always ac companied by strains and deformations. There are tensile stresses, compressive stresses, and shearing stresses. At any point on a stressed member the stress per unit area is called the "unit stress." See "Deformation." Stress is the force applied, and:
Recalescence
The sudden unproportional liberation of heat by steel when cooling through its critical range.
Scleroscope
See Hardness.
Strain
Is the resulting deformation.
Shear
Shearing Stress; See Stress.
Specific Gravity
Is a number indicating how many times a certain volume of material is heavier than an equal volume of water at a temperature of 62 0 F. The weight of one cubic inch of pure water at 62 0 F. is 0.0361 pound. If the specific gravity of any material is known, the weight of a cubic inch of the material can, therefore, be determined by multiplying its specific gravity by 0.0361.
Sorbite
See Metallography.
Static Balance
Balancing of crankshafts is a very important factor in providing long engine life. Crank shafts must be balanced for equalization of weight so that when supported on knife blades the shaft will not revolve. This is the same condition of balance that would obtain with an automobile wheel if a slight counterweight were placed directly opposite the valve stem so that the wheel if jacked up and given a spin would stop and remain stationary wherever it was overtaken by inertia after the energy from the force of the spin had spent itself. If not in perfect balance the wheel would either turn over another revolution or turn back until the heavy point was down. Elimination of the heavy place on a crankshaft is termed static balancing. This is accom plished by grinding off portions of the balancing pads forged into both sides of each throw for that purpose.
Tensile Strength
See Ultimate Tensile Strength.
Tolerance
The range of distance between specified limits,
as applied to machine shop practice.
Torsion
That force with which a twisted part tends to
return to a state of rest.
Torque
Torque is that which produces or tends to pro duce rotation or torsion; the product of tan gential force multiplied by the radius of the part it rotates. An engine is therefore es sentially a device for producing torque, and torque is the energy available for producing work. See also "Moment of Force."
Static Test
A test of a specimen in which the rate of applica tion of load is so slow that it may be regarded as zero. The term refers in general to a test made with an ordinary Tensile Testing Machine.
Toughness
Denotes a combination of strength and duc tility, resistance to fatigue, tension, and shear.
steel
The term "steel" is used to denote any ferrous
PRlNTD rN UNITED STATES OF AMERICA
Troostite
See Metallography.

Watt
A unit of electrical power or activity equal to 10 7 C.G.S. units of power (Ergs,see"Erg") or to the rate of work represented by a current of one ampere under a pressure of one volt, a volt ampere. One horsepower is approximately equal to 746 watts.
Ultimate Tensile Strength

The highest unit stress carried by a tension specimen in a test to rupture.
Velocity
See Mechanics.
Volt
The unit of electromotive force; that electro motive force which, if steadily applied to a con ductor having a resistance of one ohm, will produce a current of one ampere. It is practical ly equal to 10 0 C.G.S. Electromagnetic units.
Work
See Mechanics.
Wrought Iron
See Steel.
WEIGHTS, MEASURES, EQUIVALENTS

STANDARD WEIGHTS AND MEASURES
LONG MEASURE
12 In. 3 Ft. . . .. .. . .. .. . . . .. . . . . . . . . . . . 16-1/2 Ft............................ . 320 Rods ................................... .. 1,760 Yds. or 5,280 Ft 1 1 1 1 1 Ft. Yd. Rod Mile Mile
COMMERCIAL MEASURE OF WEIGHT

Avoirdupois or Commercial Weight 437.5 Grains 1 Oz.
16 Oz. or 7000 Grains. 1 Lb.
2,000 Lbs. 1 Net or Short Ton
(Commonly Used)
2,240 Lbs. 1 Gross or Long Ton
SQUARE MEASURE
144 Sq. In . . 1 Sq. Ft. 9 Sq. Ft. : 1 Sq. Yd. 4,840 Sq. Yds., 43,560 Sq. Ft. 1 Acre 640 Acres . j Sq. Mile An Acre=A square whose side is 208.71 Ft. long.
BOARD MEASURE
The unit of solid measure for boards is the foot board measure (B.M.). This is a volume 1 in. in thickness, 12 in. in width, and 1 ft. in length. To obtain the number of feet B.M. of a board or piece of square timber, multiply the length in feet and the breadth in feet and the thickness in inches.
SOLID OR CUBIC MEASURE

1,728 Cu. In. 1 Cu. Ft. 27 Cu. Ft. . . . . 1 Cu. Yd. I Cord Wood = A pile 4 Ft. wide x 4 Ft. high x 8 Ft. long = 128 Cu. Ft.
WEIGHT AND MEASURE EQUIVALENTS

1,728 46,656 2,150 7,056 231 144 cu. in 1 cu. ft. 27 cu. ft .. 1 cu. in 1 cu. yd. 128 cu. ft .. 1 cu. in 1 bushel 1.24 cu. ft .. I cu. in I barrel 4.08 cu. ft . I cu. in 1 gallon 20.75 cu. ft .. I cu. in 1 bd.-ft. 10.75 cu. ft .. 1 20- 23 cu. ft 1 cotton bale cu. yd. cord bushel barrel hay bale sm. bale
LIQUID MEASURE
4 Gills
1 Pt.
2 Pts.. ......................".................. .. 1 Qt.

4 Qts.. .......................... . .. .. .......... .. 1 Gal.
The U.S. Gallon 231 Cu. In. = .13373 Cu. Ft.

The English Gallon = 277.274 Cu. In.
The English Gallon = 1.20032 U.S. Gallons=The
volume of 10 Ibs. of water at 62 0 F.
SIZE OF BARRELS AND BASKETS U.S. STANDARD BUSHEL

1 Bushel 4 Pecks. 2445 cu. ft 2150.42 cu. in. 1 Peck 8 Quarts. 3 11 1 cu. ft 537.61 cu. in. 1 Quart 2 Pints. 0389 cu. ft.. 67.20 cu. in.
U. S. DRY MEASURE
pts. 1 Qt. Qts.. ........................ .... .. 1 Pk. 1 Bu. Pks .................... .. Bu.. .................... ........ .. 2150.42 Cu. In. 1.2445 Cu. Ft. A heaped bushel equals 1-1/4 struck bushels as measured above. 2 8 4 1
U.S. STANDARD BARRELS FOR VEGETABLES, FRUIT A ND DRY COMMODITIES, EXCEPT CRANBERRIES
1. Capacity 7,056 cu. in. 105 dry qts. 3.28 bu. Head diam 17.125 in. Bilge diam. 20.37 in. Stave 19th 27.125 in.

2. Capac ity 5,826 cu. in. 87 dry qts. 2.709 bu. 16.25 in. 18.62 in. 28.5 in.
GENERAL
Section 25
4. Sugar Barrel
Weight Head diam. Bilge diam Stave Igth 5.
Head diam. Bilge diam Stave Igth. 3.
. '.
300 to 360 1bs.

20.5 in.
25.0 in.
30.0 in.
Flour Barrel
Weight Head diam Bilge diarn.. Stave Igth.
.. .. . . . . . .. .
Syracuse Salt Barrel
Weight Head diam Bilge diam Stave Igth.
........
200 18 21 28.5
to 220 lbs. in. in.
in.
280 Ibs.
18 in.
21 in.
29 in.
ABBREVIATIONS FOR TERMS OF WEIGHT AND MEASURE

Following the name of each unit in the list be low is given the abbreviation which the Bureau has adopted. Attention is particularly called to the following principles: 1. The period is omitted after the abbreviations of the metric units, while it is used after thos e of the customary system. 2. The exponents "2" and "3" are used to signify area and volume, respectively, in the case of the metric units instead of the longer prefixes "sq." or "cu." In con formity with this principle the abbreviation for cubic centimeter is "cm 3tt instead of "c.c." or "c.m." The term "cubic centi meter It as used in chemical work is, in fact, a misnomer, since the unit actually used is the "milliter," which has a slightly lar ger volume. 3. The use of the same abbreviation for both singular and plural is recommended. This practice is already established in expressing metric units and is in accordance with the spirit and chief purpose of abbreviations. Abbreviation dkm 3
cubic dekameter cubic foot cu. ft.
cu.bic hectometer hm 3
cubic inch Cli, in.
cubic kilometer km 3
cubic meter m 3
cubic mile cu. mi.
cubic millimeter mm 3
cubic yard cu. yd.
decigram. dg.
dl
deciliter decimeter dm
decistere ds
dkg
dekagram dkl.
dekaliter dekameter dkm.
dks
dekastere dram or drachm, apothecaries' dr. ap. or Z dram, avoirdupois dr. avo fl. dr. dram, fluid fath. fathom ft. foot fir. firkin furlong fur. gal. gallon gr. grain gram . g. ha hectare hectogram hg hI hectoliter hm hectometer hhd. hogshead hundredweight. cwt. in. inch . , kilogram kg kiloliter . k1 kilometer km link Ii. liquid liq. liter 1 meter m metric ton t micron u mile . . mi.
milligram mg.
milliliter ml
millimeter mm
millimicron mu
4. It is also suggested that, unless all the text

is printed in capital letters, only small letters be used for abbreviations except in the case of A, for acre, where the use of the capital letter is general.
Unit acre area . avoirdupois barrel board foot . bushel carat, metr ic centare centigram. centiliter centimeter chain cubic centimeter cubic decimeter.
Abbreviation A
a
avo bbl. bd. ft. bu. c ca cg cl cm ch. cm 3 dm 3
PRINTEO IN UNITED StATES OF AMERICA
GENERAL Section Page 26 Unit

Abbreviation min. or mu oz. oz. ap. or Z oz. avo fl. oz. oz, t. pk. dwt. pt. lb. ~b. ap. lb. avo lb. t. qt. rd. S. ap. or Z cm 2 Unit square chain. square decimeter square dekameter square foot . square hectometer. square inch square kilometer square meter square mile square millimeter square rod square yard s tere ton . . . ton, metric troy yard Abbreviation sq. ch. dm 2 dkrn 2 sq. 2 hrn sq. in. km 2
minim ounce . . . . . . . . . . . ounce, apothecaries' ounce, avoirdupois ounc e, fluid ounce, troy peck pennyweight point pound ." . . . . . pound, apothecaries' pound, avoirdupois pound, troy quart . . . . . . . . . rod . . . . . . . . . . . . s c rupe, apothecaries square centimeter .
. .. .,......
tt.
sq. mi. mm 2 sq. rd. sq. yd.
s.
tn.
t t.
yd.
UNITS OF WEIGHT AND MEASURE
(From Circular No. 47 of Bureau of Standards, Department of Commerce, Washington, D.C.) THE METRIC SYSTEM: Metric units are naturally related. For example: 1 cubic deci meter equals, for all practical purposes, 1 liter, and 1 liter of water weighs 1 kilogram. The metric terms are formed by combining the wor ds "meter," "gram" and "liter" with the six numerical prefixes, as in the following table:
Length
FUNDAMENTAL UNITS A meter (m) is a unit of length equivalent to the distance between the defining lines on the international prototype meter at the International Bureau of Weights and Measures when this stand ard is at the temperature of melting ice (OoC.). 3937 1 m.;;; 3600 yd. A yard (yd.) is a unit of length equivalent to 3600 of a meter.
"393'7
Prefixes Meaning Units
HIGHER AND LOWER UNITS

kilometer (km) 1000 meters
hectometer (hm) = 100 meters.
dekameter (dkrn) ;;; 10 meters
decimeter (dm) 0.1 meter.
centimeter (cm) ;;; 0.01 meter
millimeter (rnrn) ;;; 0.001 meter;;; 0.1 centi
meter. 1 micron (u) = 0.000 001 meter 0.001 milli meter. 1 millimicron (mu) = 0.000 000 001 meter = 0.001 micron. 1200 1 foot (ft.) ;;; 3 yard :::: 3937 meter. 1 inch (in.) 1 1 100 - yard;;; foot;;; meter. 36 12 link (li) ;;; 0.22 yard = 7.92 inches. rod (rd.) ;;; 5-1/2 yards:: 16-1/2 feet. chain (ch.) = 22 yds. ;;; 100 links;;; 66 feet 4 rods. furlong (fur.) 220 yards = 40 rods 10 chains. statute mile (mi.) 1760 yards 5280 feet = 320 rods. hand = 4 inches. 1 inch. 72 1 1 1 1 1 1
1 milli- ==one-thousandth 1000

centi ;;;one-hundredth decione-tenth
1 100 1 10
10 100 -11 10
001 "meter" for length 01

1
Unit = one deka- ;;; ten hecto- ;;; one hundred kilo- ;;; one thousand
"gram" for weight or mass
100
"liter" for capacity
1000 1000 1
Definitions of Units
The following lists of units include most of those in general use. Simple conversions may be made from the values here given. For example, if a conversion into nautical miles is wanted, the conversion factor for statute mile given in the conversion tables may be used by multiplying it by the factor 1.151553 here given to show relation of nautical mile to statute mile.
1 1 1 1 1 1
1 point

1 1 1 1 1 1 mil 0.001 inch.
fathom::: 6 feet.
span::: 9 inches 1/8 nautical mile seal mile [ geographical mile
1 cubic millimeter (rnrn 3 ) :: 0.000 000 001 cubic meter = 0.001 cubic centimeter. fathom.
United States:::6080.20
feet:::l.I51 553 statute
miles:::1353.249 meters
1 cubic foot (cu. ft.) :;; 2; cubic yard. 1 cubic inch (cu. in.) :::
46~56
cubic yard
Area
FUNDAMENTAL UNITS A square meter (m 2 ) ::: 1.195985 sq. yd.
A square yard (sq. yd.) ::: 0.8361307 m 2
HIGHER AND LOWER UNITS 1 square kilometer (km 2 ) ::: 1 000 000 square meters. 1 hectare (ha) or square hectometer (hm 2 ) ::: 10 000 square meters. 1 area (a), or square dekameter (dkm 2 ) ::: 100 square meters. 1 centare (ca) ::: 1 square meter. 1 square decimeter (dm 2 ) 0.01 square meter. 1 square centimeter (cm 2 ) ::: 0.0001 square meter. 1 square millimeter (rnrn 2 ) 0.000 001 square meter::: 0.01 square centimeter. 1 square foot (sq. ft.) 9 square yard.
1
17~8
cubic foot.
1 board foot::: 144 cubic inches - 1 cubic foot. -12
1 cor d (cd.)
128 cubic feet.
Capacity
FUNDAMENTAL UNITS A liter (1) is a unit of capacity equivalent to the volume occupied by the mass of 1 kilogram of pure water at its maximum density (at a temperature of 4 0 C. practically and under the standard atmospheric pressure of 760 mm). It is equivalent in volume to 1.00 027 cubic deci meters. One liter 0.264168 gal. A gallon (gal.) is a unit of capacity equivalent to the volume of 231 cubic inches. It is used for the measurement of liquid commodities only. 1 gal. ::: 3.785 332 lite;r. A British gallon is approximately 20 percent lar ger. A bushel (bu.) is a unit of capacity equivalent to the volume of 2150.42 cubic inches. It is used in the measurement of dry commodities only. The bushel is the so-called stricken or struck bushel. Many dry commodities are sold by heaped bushel, which is generally specified in the State Laws to be the usual stricken bushel measure "duly heaped in the form of a cone as high as the article will admit" or "heaped as high as may be without special effort or design." The heaped bushel was originally intended to be 25 percent greater than the bushel. A British bushel is 3 percent larger. HIGHER AND LOWER UNITS 1 hectoliter (hI) ::: 100 liters. I dekaliter (dkl)::: 10 liters. 1 deciliter (dl) ::: 0.1 liter. 1 centiliter (el) ::: 0.01 liter. 1 milliliter (ml) ::: 0.001 liter::: 1.000 027 cubic centimeters. 1 liquid quart (liq. qt.) ::: 1/4 gallon::: 57.75 cubic inches. 1 liquid pint (liq. pt.) = 1/8 gallon = 1/2 liquid quart::: 28.875 cubic inches. 1 gill (gi.) 1/32 gallon::: 1/4 liquid pint ::: 7.21875 cubic inches 1 fluid ounce (fl. oz.) ::: _t_ gallon:: 1/16 liquid 128 pint. fluid dram (f1. dr.) ::: 1/8 fluid ounce::: _1_ 128 liquid pint. minim (min.) =_1_ fluid dram:: 1/4 80 fluid 60 ounce. 1 fir kin (fir.) = 9 gallons.
1 1 square inch (sq. in.) ::: 1296 square yard :::

1 144 square
foot.
1 square link (sq. li.) 0.0484 square yard ::: 62.7264 square inches. 1 square rod (sq. rd.) ::: 30.25 square yards ::: 272.25 square feet::: 625 square links. 1 square chain (sq. ch.) = 484 square yards ::: 16 square rods::: 100 000 square links. 1 acre (A) ::: 4840 square yards:: 160 square rods 10 square chains. 1 square mile (sq. mi.) ::: 3 097 600 square yards 640 acres.
Volume
FUNDAMENTAL UNITS A cubic meter (m 3 ) ;; 1.307 9428 cu. yd. A cubic yard (cu. yd.) .017645594 m. HIGHER AND LOWER UNITS 1 cubic kilometer (krn 3 ) ::: 1 000 000 000 cubic meters. 1 cubic hectometer (hm 3 ) ::: 1 000 000 cubic meters. 1 cubic dekameter (dkrn 3 ) ::: 1000 cubic meters. 1 stere (s) :: cubic meter. 1 cubic decimeter (dm 3 ) 0.001 cubic meter. 1 cubic centimeter (cm 3 ) ::: 0.000 001 cubic meter ::: 0.001 cubic decimeter.
PRINTED IN UNITED STATES OF .AMERICA

1 apothecaries' pound (lb. ap.) = 1 troy pound: 5760. . aVOIrdupoIs pound. 7000 1 apothecaries' or troy ounce (oz. ap. or z, or oz. t.) = 112 troy pound = 480 avoirdupois 7000
pound 480 grains.
apothe96 caries' pound = 1/8 apothecaries' ounce::: 60 grains. 1 pennyweight (dwt.) _1_ troy ounce = 24 grains. 20 1 1 apothecaries' scruple (s. ap. or S): apothe 3 caries' dram 20 grains. 1 metric carat (c) 200 milligrams::: 0.2 gram. The old carat in use in this country previous to July 1,1913, was of 205.3 milligrams. 1 short hundredweight (sh. cwt.) 100 avoirdu pois pounds. 1 long hundredweight (1 cwt.) 112 avoirdu pois pounds. 1 short ton (she tn.) = 2000 avoirdupois pounds. 1 long ton (I. tn.) = 2240 avoirdupois pounds.
1 peck (pk.) = 1/4 bushel = 537.605 cubic inches. 1 dry quart (dry qt.) 1/32 bushel 1/8 peck = 67.200 625 cubic. inches. 1 dry pint (dry pt.) = 1/64 bushel = 1/2 dry quart: 33.600 312 5 cubic inches. 1 barrel (bbl.) (for fruit, vegetables and other dry commodities) = 7056 cubic inches:::: 105 dry quarts (By U.S. Statute, March 4, 1915).
Mass or Weight
FUNDAMENTAL UNITS A kilogram (kg) is a unit of mass equivalent to the mass of the International prototype kilogram at the International Bureau of Weights and Measures. One kg. = 2.204 622 341 lb. avo An avoirdupois pound (lb. av.) = 0.453 592 427 7 kilogram. A gram (g) is a unit of mass equivalent to one-thousandth of the mass of the International prototype kilogram at the International Bureau of Weights and Measures. A troy pound (lb. 61) is a unit of mass equivalent to 5760/7000 of that of the avoirdupois pound. HIGHER AND LOWER UNITS metric ton (t) = 1000 kilograms.
hectogram (hg) = 100 grams = 0.1 kilogram. dekagram (dkg) = 10 grams = 0.01 kilogram.
decigram (dg) = 0.1 gram. centigram (cg) 0.01 gram.
milligram (mg) = 0.001 gram. 1 avoirdupois ounce (oz. av.) =~ avoirdupois pound. 6 1 avoirdupois dram {dr. av.} = 1/2 56 avoirdupois pound: 1/16 avoirdupois ounce.
1 apothecaries' dram (dr. ap or Z)
=.l...
1 1 1 1 1 1
FRENCH AND AMERICAN EQUIVALENT MEASUREMENTS

Measures of Length
FRENCH 1 meter .3048 1 2.54 1 25.4

1
meter centimeter centimeters millimeter millimeters kilometer
1 grain (gr.)
avoirdupois pound = ~ 7000 4375 avoirdupois ounce = __ troy pound. 1_ 5760
=__ 1_
AMERICAN
inches, or 3.28083 feet 1 foot .3937 inch 1 inch .03937 inch, or..l inch nearly 22 1 inch 1093.61 yards, or .62137 mile 39.37
EQUIVALENT VALUES OF ELECTRICAL, MECHANICAL AND HEAT UNITS

Units 1,000 1.341 2,655,180 3,600,000 3,415 367,100 0.234 3.52 22.77 0.7457 1,980,000 2,546.5 273,740 0.174 2.62 17.0 Equivalent Value watt hours horsepower hours
ft.-1bs.
joules
heat units kilogram meters lb. carbon oxidized with perfect efficiency Ibs. water evaporated from and at 212 degrees F. Ibs. water raised from 62 degrees to 212 degrees F. kilowatt hour ft.-lb. heat units per hour kilogram meters lb. carbon oxidized with perfect efficiency lb. water evaporated from and at 212 degrees F. lb. water raised from 62 degrees to 212 degrees F.
1 Kilowatt Hour
Horsepower Hour

Unit 1,000 1.3410 2,655,180 44,253 737.56 3,415 56.92 0.9846 0.234 3.52 745.7 0.7457 33,000 550 2,546.5 42.44 0.707 '0.174 2.62 1 0.000000278 0.102 0.0009486 0.73756 1.3558 0.13826 0.0000003766 0.0012861 0.0000005 1 0.001341 3.415 0.73756 0.0035 44.254 Equivalent Value in Other Units
1 Kilowatt =
watts horsepower ft.-1bs. per hour ft.-lbs. per minute ft.-lbs. per second heat units per hour heat units per minute heat units per second lb. carbon oxidized per hour Ibs. water evap. per hour from and at 212 degrees F. watts kilowatt ft.-lbs. per minute ft.-lbs. per second heat units heat units per minute heat units per second lb. carbon oxidized per hour lb. water evap. per hour from and at 212 degrees F. watt second kilowatt hour kilogram meter heat unit ft.-lb. joules kilogram meter kilowatt hour heat unit horsepower hour joule per second horsepower heat units per hour ft.-lb. per second lb. water evap. per hour ft.-lbs. per minute
1 HORSEPOWER
Joule
1
Ft.-Lb.=
------------~---------------------------------------------------.
1 Watt
1 Watt per Sq. In. =
8.20 6,373 0.1931 1,054.2 777 .54 107.5 0.0002928 0.0003927 0.0000685 0.001030 1.1220 0.01757 0.02356 7.233 0.000003653 0.000002724 0.009302
heat units per sq. ft. per minute ft.-lbs. per sq. ft. per minute horsepower per sq. ft. watt seconds ft-lbs. kilogram meters kilowatt hour horsepower hour lb. carbon oxidized lb. water evap. from and at 212 watt per sq. in. kilowatt per sq. ft. horsepower per sq. ft. ft.-lbs. horsepower hour kilowatt hour heat unit
1 B.T.U.
or
1 Heat Unit
ees F.
1 Heat Unit per sq. ft. per min.
1 Kilogram Meter ::::
PRINTED IN VNITD $'fA'tES OF ""'ERICA
GENERAL Section Page 30 Unit

Equivalent Value in Other Units
14,600
1 lb. Carbon Oxidized with perfect efficiency;;;;
1.11
2.5 22 4.275 5.733 11.352,000 15.05 0.2841 0.3811 970.4
104,320
1,023,000
754,525 0.066466
heat units Ibs. anthracite coal oxidized Ibs. dry wood oxidized cubic feet illuminating gas kilowatt hours horsepower hours Ibs. of water evap. from and at 212 degrees F. kilowatt hour horsepower hour heat units kilogram meters joules ft.-lbs. lb. carbon oxidized
1 lb. Water
Evap. from and at
212 degrees F. :;::
GENERAL
Section Page 31
MATHEMATICAL SALES
ROAD SPEED FORMULAS
FORMULAS ENGINEERING
USED
IN
GRADE ABILITY FORMULAS
TORQUE FORMULAS
MPH = RPM x r R x 168

RPM = MPH x R x 168
GA=TF -
RR
TF=GA+RR
GA= T x 12 x R x E GVWxr GVW=Tx 12xRxE TF x r T=TFx GVW x r
12 x R x E
R=TFx GVW x r 12 x T x E
HORSEPOWER FORMULAS
T=D x BMEP
150.8 RR T =D x 0.75 (Approx.) T=BHP x 5252 RPM
DRAWBAR PULL
RPMxr R=MPH x 168 WHEEL RPM = MPH x 166

r
TRACTIVE EFFORT FORMULAS
DBP=TE - RR
CLUTCH TORQUE CAPACITY
TE= T x 12 x R x E
r
T= R=
TExr 12 x R x E TE x r
T x 12 x E
lliP=MEP x A x S x N 33000 x C S = Stroke (Ft.) x RPM lliP = BHP + Friction HP BHP = BMEP x A x S x N 33000 x C BHP=2 x RPM x BHP=T x RPM 5252 BHP = D x RPM x 0.75 (Approx.) 5252
7r
Total Spring Pressure x T = Mean Radius of Lining x 2 Faces x .25 Coeffi lcient of Friction + 12
GRADE ABILlTY HORSEPOWER FORMULAS
TRACTIVE FACTOR FORMULAS
TF= T x 12 x R x E GVWxr T=TF x GVW x r 12 x R x E GVW=.T x 12 x R x E TF x r R=TF x GVW x r T x 12 x E
GA = 33750 x BHP _ RR GVW x MPH GVW 33750 x BHP MPH x TF
xT
33000
MPH = 33750 x BHP GVW x TF HP= GVW x MPH x TF

33750
KEY
TO
SYMBOLS
N
r
USED
ABOVE
A = Area of piston head in sq. in. BHP = Brake horsepower. BMEP = Brake mean effective pressure. C =No. cycles (4 for IH). D = Piston displacement in cu. in. DBP = Drawbar pull. E = Mechanical efficiency (.90 direct, .85 in other gears). GA = Grade ability, factor (G x 100 = % Grade). GVW = Gross weight, lb. IHP = Indicated horsepower. MEP = Mean effective pressure. MPH = Miles per ho.ur.
PRINTED IN UNITED STATES OF A""ERICA
=Number of cylinders.
= Effective tire radius (loaded) (inches)
R =Total reduction to 1.00.
RPM = Engine speed revolutions per minute
(r.p.m.)
=Rolling or road resistance (.012 lbs. for
RR good concrete roads.
= Piston speed in feet per minute. S = Torque-lb.-ft. T TE = Tractive effort, lb. TF = Tractive factor, lb. per lb. gross. =Pi=3.1416; ratio of diameter to circumference of circle.
GENERAL
Section Page 32
POUNDS OF GROSS VEHICLE WEIGHT WHICH ONE HORSEPOWER

DELIVER ED TO CLUTCH WILL PULL UP
VARIOUS GRADES AT VARIOUS SPEEDS
SPEED-MILES PER HOUR

Grade
%
0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9 2.0 2.1 2.2 2.3 2.4 2.5 2.6 2.7 2.8 2.9 3.0 3.1 3.2 3.3 3.4 3.5 3.6 3.7 3.8 3.9 4.0 4.1 4.2 4.3 4.4 4.5 4.6 4.7 4.8 4.9 5.0 5.1 5.2 5.3 5.4 5.5 5.6 5.7 5.8 5.9
15
16
17
18
19
20
21
22
23
24
25 964
26 998 928 865 810 764 722 683 648 617 590 562
27
28 927 861 804 753 710 670 635 602 573 548 522 502 482 463 446 430 416 401 389 377 366 355 345 335 326 317 309 301 294 287 280 274 267 262 257 251 246 241 236 231 227 223 219 215 211 207 204 200 198 194 191 188 185 183 180 177 175 172 170
29 895 832 777 728 685 648 612 581 553 529 504 484 465 448 431 416 401 387 375 364 352 342 332 323 314
306
30
35
40 649 603 563 527 496 469

444
45
50 Grade
MORE THAN
1000 LBS. 993 988 937 935 890 889 843 845 802 808 768 772 732 740 702 710 675 684 650 658 625 634 602 612 581 592 562 573 544 555 527 537 511 523 496 507 482 494 469 480 456 467 444 455 432 443 421 433 411 422 400 413 392 404 383 395 375 386 366 378 359 370 351 362 344 355 337 348 330 341 324 335 318 328 312 323 307 317 301 311 295 306 290 300 286 295 281 291 276 286 212 282 268 277 264 273 260 269 256 265 252 261 ~ 257 244 254 241 250 238 1000 947 894 847 803 765 730 697 670 643 619 595 573 554 536 519 502 486 473 459 446 434 423 412 401 392 382 374 365 357 349 342 334 327 321 315
309
1000 959 978 917 937 878

900
844
867 833 803 776 750 727 703

680
661 642 625 608 591 576 561 548 535 523 511
812 781 754 727 703 681 659 639 620 601 585 570 555
540
527 514 503 490 479
500 468 489 457
478 449 468 439 458 430 450 422 441 413 432 405 424 397 416 390 409 383 401 376 394 370 387 363 381 357 375 351 369 346 363 340 357 335 351 330 346 325 341 320 336 315 331 310 326 306 321 301 317 297
987 936 890 854 813 782 750 722 694 670 647 662 625 641 606 620 586 600 567 584 551 566 535 552 520 536 507 522 493 508 480 495 468 484 457 472 446 462 436 451 425 441 416 431 407 422 399 413 390 405 382 397 375 389 367 381 360 374 353 367 347 361 341 354 335 348 328 342 323 336 318 331 312 325 307 320 302 315 298 310 293 305 289 301 284 296 280 292 276 288 272 283 268 280 264 993 945 903 862 827 795 764 736 709 685
958 903 853 808 766 730 697

665
303 297 292 287 282 277 212 268 263 259 255 251 247 244 240 236 233 229 226
639 613 591 568 547 529 511 495 479 465 452 438 426 415 404 394 383 374 365 357 348 341 333 326 319 313 307 300 294 289 284 279 274 269 264 260 255 251 247 244 240 236 233 229 226 223 219 216
978 917 863 817 773 733 698 667 638 611 587 565 543 524
506
488 473 458 444 432 419 407 397 386 376 367 358 349 341 333 326 319 312 305 299 293 287 282 276 212 267 262 257 253 249 244 24) 235 233 229 226 223 219 216 213 210 207
938 879 827 782 741 702 669 639 611 586 563 542 521 502 484 468 453 439 425 414 401 391 380 370 360 351 343 334 327 319 312 305 299 292 287 281 275 270 265 260 255 251 246 242 238 234 231 226 223 220 216 213 210 207 204 200 198
900
844 795 750 711 674 642 613 586 562

540
520 500 482 465 450 435 422 409 397 386 375 365 356 346 337 329 321 314 307 300 293 287 281 275 270 264 259 254 250 245 241 237 232 228 224 221 218 214 211 208 205 202 199 196 193 190
962 893 834 781 736 695 658 625 594 567 542 540 521 519 500 500 481 481 462 463 446 447 431 432 416 419 403 406 390 393 378 382 368 371 357 361 348 351 338 342 329 333 320 324 312 317 304 309 297 302 290 295 284 288 277 282 272 276 266 270 260 265 255 260 250 254 245 249 240 244 236 240 231 236 227 232 223 227 219 223 217 220 212 216 208 213 205 209 202 206 198 203 195 200 192 197 189 194 187 191 184 188 181 185 179 183 176
298 291 283 277 271 264 258 253 248 242 237 233 228 223 219 215 211 208 204 201 197 194 191 188 185 182 179 176 174 171 169 166 164
865 742 804 689 750 643 702 603 662 567 625 536 593 507 561 482 535 459 511 438 488 419 469 402 450 386 433 371 410 357 401 344 388 333 375 321 363 311 352 301 341 292 331 284 322 276 312 268 304 261 296 254 288 247 281 241 274 235 268 230 262 224 256 219 250 214 244 210 239 205 234 201 229 197 225 193 221 189 216 185 212 182 208 179 204 175 200 172 197 169 194 166 191 163 188 160 184 158 181 156 179 153 176 151 173 148 170 146 168 144 165 142 163 140 161 138 158 136
422 402 384 367 352 338 325 313 301 290 281 272 264 256 248 241
234
228 222 216 211

206
201 196 192 188 183 180 176 172 169 165 162 159 156 153 151 148 145 143 140 138 136 134 132 130 128 126 124 122 121 119
577 519 536 482 500 450 469 422 441 397 417 375 395 355 375 338 357 321 341 307 326 293 313 281 300 270 288 260 278 250 268 241 259 233 250 225 242 218 234 211 227 205 221 199 214 193 208 188 203 182 197 178 192 173 188 169 183 165 179 161 174 157 170 153 167 150 163 147 160 144 156 141 153 138 150 135 147 132 144 130 142 127 139 125 136 123 134 121 132 118 129 116 127 114 125 113 123 111 121 109 119 107 117 105 115 104 114 102 112 101 110 99 109 97 107 96 106 95
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1.0
1.1
1.2
1.3
1.4
1.5
1.6
1.7
1.8
1.9
2.0
2.1
2.2
2.3
2.4
2.5
2.6
2.7
2.8
2.9
3.0
3.1
3.2
3.3
3.4
3.5
3.6
3.7
3.8
3.9
4.0
4.1
4.2
4.3
4.4
4.5
4.6
4.7
4.8
4.9
5.0
5.1
5.2
5.3
5.4
5.5
5.6
5.7
5.8
5.9
L-UNE MOTOR TRUCK SERVJCE MANUAL

SPEED-MILES PER HR.
Grade
15 312 308 304 300 296 292 288 284 281 278 274 271 267 264 263 259 256 253 250 248 245 242 239 236 234 232 230 227 225 223 220 218 216 214 212 210 208 206 204 202 201
16 293 289 285 281 278 274 270 266 263 260 257 254 251 248 245 242 240 237 234 232 229 227 224 222 220 217 215 213 2ll 209 207 205 203 201 199 197 195 193 192 190 188
17 275 272 268 264 261 258 254 251 248 245 242 239 236 234 231 228 226 223 221 218 216 213 211 209 207 205 203 201 199 197 195 193 191 189 187 186 184 182 180 179 177
18 260 257 254 250 247 244 240 237 234 231 228 226 223 221 218 216 213 211 208 206 204 202 199 197 195 193 191 189 188 186 184 182 180 179 177 175 174 172 170 169 167
19 246 243 240 237 234 230 227 224 221 219 216 214 2ll 209 207 204 202 200 197 195 193 191 189 187 185 183 181 179 178 176 174 172 171 169 168 166 164 163 161 160 159
20 234 231 228 225 222 219 216 213 211 208 206 203 201 199 196 194 192 190 188 185 183 182 180 178 176 174 172 171 169 167 165 164 162 161 159 158 156 155 153 152 151
21 223 220 217 214 211 209 206 203 201 198 196 194 191 189 189 185 183 181 179 177 175 173 171 169 167 166 164 162 160 159 158 156 155 153 152 150 149 147 146 145 143
22 213 210 207 204 202 199 197 194 192 189 187 184 182 180 178 176 174 172 170 169 167 165 163 161 180 158 157 155 153 152 150 149 148 146 145 143 142 141 139 138 137
23 204 201 198 196 193 191 188 186 183 181 179 177 175 173 171 169 167 165 163 161 159 158 156 154 153 151 150 148 147 145 144 142 141 140 138 137 136 135 133 132 131
24 195 193 190 187 185 183 180 178 176 174 171 169 167 165 163 162 160 158 156 155 153 151 150 148 146 145 143 142 141 139 138 137 135 134 133 131 130 129 128 127 126
25 188 185 182 180 178 175 173 171 169 167 165 163 161 159 157 155 153 152 150 148 147 145 144 142 141 139 138 137 136 134 132 131 130 129 127 126 125 124 123 122 120
26 180 178 175 173 171 169 166 164 162 160 158 156 155 153 151 149 148 146 144 143 141 140 138 137 135 134 132 131 130 129 127 126 125 124 122 121 120 119 118 117 116
27 174 171 169 167 164 162 160 158 156 154 152 151 149 147 145 144 142 140 139 137 136 134 133 132 130 129 128 126 125 124 123 121 120 119 118 117 116 115 114 113 112
28 167 165 163 161 159 156 154 153 151 149 147 145 143 142 140 139 137 135 134 132 131 130 128 127 126 124 123 122 121 119 118 117 116 115 114 113 112
29
30 156 154 152 150 148 146 144 142 140 139 137 136 134 132 131 129 128 126 125 124 122 121 120 118 117 116 115 114 113 111 110 109 108 107 106 105 104 103 102 101 100
35 134 132 130 129 127 125 124 122 121 119 118 ll6 US U3 ll2 111 110 108 107 106 105 104 103 102 100 99 98 97 96 95 94 94 93 92 91 89 88 87 86
88
90
40 117 116 114 113 111 110 108 107 105 104 103 102 100 99 98 97 96 95 94 93 92 91 89 88 87 86 8:;; 84 83 83 82 81 80 79 79 78 77 77 76 75
90
45 104 103 101 100 99 97 96 95 92 91 90 89 87 86 85 84 83 82 81 81 80 79 78 77 76 76 75 74 73 73 72 71 71 70 69 69 68 67 67

88
94
50 Grade 94 92 91 90 89 88 86 85 84 83 82 81 80 79 78 77 77 76 75 74 73
72
6.0 6.1 6.2 6.3 6.4 6.5 6.6 6.7 6.8 6.9 7.0 7.1 7.2 7.3 7.4 7.5 7.6 7.7 7.8 7.9 8.0 8.1 8.2 8.3 8.4 8.5 8.6 8.7 8.8 8.9 9.0 9.1 9.2 9.3 9.4 9.5 9.6 9.7 9.8 9.9 10.0
162 159 157 155 153 151 149 147 146 144 142 140 139 137 135 134 132 131 129 128 127 125 124 122 121 120 119 118 116 ll5 114 113 ll2 111 110 109 108 III 107 110 106 109 105 108 104
72 71 70 69 69 68 67 67 66 65 65 64 64 63 62 62 61 61
60
6.0 6.1 6.2 6.3 6.4 6.5 6.6 6.7 6.8 6.9 7.0 7.1 7.2 7.3 7.4 7.5 7.6 7.7 7.8 7.9 8.0 8.1 8.2 8.3 8.4 8.5 8.6 8.7 8.8 8.9 9.0 9.1 9.2 9.3 9.4 9.5 9.6 9.7 9.8 9.9 10.0
ROAD-ENGINE SPEED FORMULAS

8 --Road speed in miles per hour.
RPM-Engine speed in revolutions per minute.
r -Tire rolling radius in inches.
R -Total gear reduction = Rear axle ratio x Transmission ratio.
ABILITY' FORMULAS
GVW-Gross weight of vehicle (or combination) in pounds.
-Road speed in miles per hour,
8 HP -Power delivered to clutch at road speed 8 in particular
transmission ratio being used. -Grade.in per cent. G In the following ability formulas, a value of 1.2 lbs. per 100 lbs. of gross weight is used for rolling resistance. Power lost in overcoming friction between the clutch and the driving wheels is taken at 0,1 of the power delivered to the clutch by the engine and an efficiency factor of 0.9 has accordingly been incorporated in the formulas. 1--GVW =~3750 ~ HP 8(G+1.2) 2-GVW = 33750 3(8+1.2) =Lbs. per Horsepower HP 5-8 = RPM x r 168 x R
PRINTEO IN UNITEO STATES OF AM~RIC"
3-8
33750 x HP GVW (G+1.2)
4-G _ 33750 x HP-1.2 -GVWx 8 6-RPM= 168 x R x 8

r
GENERAL
Section Page 34
CONVERSION CHART-LIQUIDS
BRITISH IMPERIAL and U. S. MEASURE
I I
I i
I
I
1--1----11---1--+-+-+I--+!--,--'I_+-1'-+--i-'-!--+---+--+--;-!-+-+1---'---+-+-V7-'-lJ~-i:----:---+- I
26
1--'-+-r~+-~-+~~4-+-~-+~~I-+l-r~/_~+I-+~+-~!~~24 I L
I
!
1
I I
I
I
I
i
,
I
I
!
I
I I
i
I
I
1
!
I
i
GENERAL
Section 35
1-60 -40
-20
20 3240
"18 19 20 >c::
V
60 80 120 100 DEGREES FAHRENHEIT

I I I I I I I
To con veri 0 Flo C or vice versa read to diagonal line Ihen 10 de.ired scale
140
160
180
I
J
200 212 220 ~O

/
'\.
~30
/.
/:
"- '\
!\.
"'-
I I I I
EXAMPLE
I
I
/
I I
[ I
~20
/(
:::>
1.0.1
c::
'"
!
1 , I,
1\
~
I
I
/'
/" VI
~10
0
I
21 :E
r-- C>
"'"
I')
22 ::r:
-
t.IJ
'""
V
/
....
I
/
I 23 t.IJ
c::
""
"" '"
I
Y VI
V
'\
_ 1__,
10
/
I
/ I
To d~l.rmin. approximate _ boiling point of waler al .ariou. altitudes dr. w line _ from kno wn altil ude thru mark (0) 10 Ihe ~F H.I. _
< c:: 20
C.;l
t.IJ
t-
1=
Z t.IJ
t-
r-- :::> I')

I')
24
~
~
/
_
I--
"'-
"''\.
I. I
J,
I' I
I
I
EXAMPLE
r--,v 25 '~
t.IJ
To delermlne approximate altilud. from ?atometric

pressure or
VHf
versa
4~
27.
28
r a d I 0 I hi. lin r .... Ihen 10 desired s(Ol~
y
I
I
I"
30 t.IJ t.IJ
eg- 40
V
I')
t.IJ
V EXAMPLE V . I~
/
V
/1
f
'" '"
i
.... _.-
50
I
/V
/
/
I
/
'" '"
60 70
"\.
~
~
29
I
I
!\. !\.
I I
tt
90
A23216
/
1
VI
ALTITUDE IN THOUSANDS OF FEET 8 7 5 6' 9 10
"'
11
12
13'\. 14 100
PRINTED IN UNITEO STATES OF AMERICA
R~LINE
MOTOR TRUCK SERVICE
AXLE-FRONT Specifications Page 1
FRONT AXLE
Specifications covering IHC F-553-A Front Axle for Truck Models R-lS53 to RF-194.inclusive and the Timken FE-900 Front Axle for Truck Models R-190 to RF-Z10 inclusive are listed in the following chart:
FRONT AXLE SPE CIFICA TIONS

. FRONT AXLE MODEL Tie Rod Diameter Knuckle Pin Diameter Knuckle Pin Length Knuckle Pin Thrust Bearing Type Steering Knuckle Spindle Diameter: At Inner Bearing Diameter At Outer Bearing Diameter I-Beam Section Alignment Data: *A-Center of Steering Arm Ball to level of Spring Pad *B -Spring Centers *E-Camber at Rim (D.egrees) *F -Knuc~le Pin Inclination (Degrees) *G-Caster (Degrees) *H-Center of Steering Arm Ball
to Center Line of I-Beam
*MN -Toe-In (Measured from
Thread Centers with Cambers
and Caster according to
Specifications)
F-553-A 1 ~ 1/s11 FE-900
I-liz"
1-39/6411 (large end)
9-314 11
Roller
1-15/16" 4-Z1/3Z"
Ball
z-1/16" 1-5/16"
3- 3/Sxz -1/4"
Z - 3/s"
1-3/4"
4x3- 9/16"
4-1/16 11 31-1/8"
10
40 ZO to 3 0
4-3/4" 31-1/s"
10
5-l/z o
ZO to 3 0
. ...
,.
......... .
.. . . ..
. .. . . .. . .
l/16-1/s"
1/16-1/sl1
* Key letters
refer to illustrations appearing under Axle-Front, Section A, page 3, L-Line.

PRINTED IN UNITE.D STATES OF' AMERICA.
CTS Il-MARCH 1953 (Supplement.l pages for CTSlll.
AXLE-FRONT Specifications and Index Page 1
FRONT AXLE GROUP
Motor truck models and their corresponding front axle models are shown in the following list. Axle model specifications will be found on page 2 of this section. TRUCK MODEL AXLE MODEL TRUCK MODEL F-160 F-170 F-l70 F-170 F ... 170 F-2S0 F-2S0 F-270 F-360 F-360 F-360 F-360 F-360 F-5S0 F-5S0 F-5S0 F-5S0 F-5S0 AXLE MODEL
F-5BO
F-5BO
L-lIO . . . . . . . . . . . . . . . . . . L-120 . . . . . . . . ' . . . . . . . . LM-120 . . . . . . . . . . . . . . . L-130 . . . . . . . . . . . . . . LB-140 . . . . . . . . . . . . . . . . L-150 . . . . . . . . . . . . . . . . . . . L-153 . . . . . . . . . . . . . . . . . LM-150 . . . . . . . . . . . . . . . . . L-l60 . . . . . . . . . . . . . . . . . . L-163 . . . . . . . . . . . . . . . . . . . . . L-164 . . . . . . . . . . . . . . . . . . L-165 . . . . . . . . . . . . . . . LC-l60 . . . . . . . . . . . . . . . . . . . . L-170 . . . . . . . . . . . . . . . . . . . L-173 . . . . . . . . . . . . . . . . . . L-174 . . . . . . . . . . . . . . . . . . . L-175 . . . . . . . . . . . . . . . . . . . LF-170 . . . . . . . . . L-IBO . . . . . . . . . . . . . . . L-IB3 . . . . . . . . . . . . . . . . .
L-IS4 . . . . . . . . . . . L-lS5 . . . . . . . . . . . . LC-lS0. . . . . . . . . . . . L-190 . . . . . . . . . . . . . L-193 . . . . . . . . . . . . . . . . L-194 . . . . . . . . . . . . . . . . . . " L-195.. . . . . . . . . . . . . . LC-l90 . . . . . . . . . . . . . . . . . . . LF-190 . . . . . . . . . . . . . . . . L-200 . . . . . . . . . . . . . . . . . L-204.. . . . . . . . . . . . . . L-205 . . . . . . . . . LC-200 . . . . . . . . . . " . . . . . L-210 . . . . . . . . . . . . . . . . LF-210 . . . . . . . . . . . . . . L-220 . . . . . . . . . . . . . L-225 . . . . . . . . . . . . . . LF-220 . . . . . . . . . . . . F-5BO L-230 . . . . . . . . . . . . . F-5BO LF-230 . . . . . . . . . . . . . . .
F-5S0
F-553
F-553
F-553
F-553
F-553
F-553
F-653
F-653
F-653
F-653
F-751
F-751

F-750
F-750

INDEX
Front axle specifications . . . . . . . . . . . . . . . . . . . . . . . . . . .
Page
2
SECTION "A" - F-160, F-170, FRONT AXLES

.Ax.le caster ........................ Knuckle pin inclination . . . . . . . . . . . . . . . . . . . . . . . . . . . . Refitting knuckle pin bushings. . . . . . . . . . . . . . . . . . . . . . . . . Steering knuckle pins and bearings . . . . . . . . . . . . . . . . . . . . . Steering knuckle stop screws. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Tie rod . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Whee I alignment. . . . . . . . . . . . . . . . . . . . . . . . . . . Whee 1 cambe r . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Wheel toe-in . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
II .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
3
3
1, 2
1
2
2
2
3
2, 3
SECTION "B" - F-270, F-280, F-360, F-580, F-553,

F-653, F-750, F-751, FRONT AXLES
Axle caster. . . . . . . . . . . . . . . . . . . . . . . . . . . . Knuckle pin inc lination . . . . . . . . . . . . . . . . . . . Refitting knuckle pin bushings. . . . . . . . . . . . . . . . . . . Steering knuckle pins and bearings . . . . . . . . . . . . . Steering knuckle stop screws . . . . . . . . . . . . . . . . " Tie rod. . . . . . . . . . . . . . . . . . . . . . . . . . . Whe e I alignment . . . . . . . . . . . . . . . . . . . . . . . Wheel Gamber. . . . . . . . . . . . . . . . . . . . Wheel toe-in. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
4
I
1
2, 3
3
3
3, 4
3
SECTION "C"
Suggested wheel alignment trouble shooting chart.

PRINTED IN UNITED 5TA,TS OF "MERle'"
OQ('I):><
~.w> t"II ~. t<

I"l
I
FRONT AXLE SPECIFICATIONS

FRONT AXLE MODEL Tie Rod Dianneter Knuckle Pin Diannete r Knuckle Pin Dianneter 0.5. Knuckle Pin Dianneter 0.5. Knuckle Pin Length Knuckle Pin Thrust Bear ing Type Steering Knuckle Spindle Dianneter: At Inner Bearing Dianneter At Outer Bearing Dianneter I-Beann Section Alignnnent Data: A-Center of Steering Arnn Ball To Level of Spring Pad B-Spring Centers E-Cannber At Rinn (Degrees) F-Knuckle Pin Inclina tion G-Caster - Degree H-Center of Steering Arnn Ball to Center Line of I-Beann MN-Toe-In (Measured Fronn Tread Centers With C annbe rand Caster According to Specifications 5-7116 f1 Ball 5-7/16 1t Ball 6-1/4" Roller 6-1/4" Roller 6-1/4" Roller 6-3/4" Roller 7-21/3211 Roller 7-1/2" Roller 9-5/8 11 Roller 9-5/8 11 Roller F-I60 3/4" .861 .876 F-I70
-
N::t!t::I
III I:tj
p;:;o 00
::l
til
F-270
----
F-280
111
F-360 I" 1.110
F-580 1-1/8 11 1.234
F-553 1-1/8" 1.234
F-653 1-1/4 11 1.484
F-750 1-1/2" 1.359
F-751 1-1/2" 1.359
Z 1--3
3/4" .861 .876
I" 1.110
1.110
r[Tl
t z
s:
-l
C
1.3125 .8122 2-1/4" x 1-11/16"
125 .8122
1.562 .937
1.562 .937 2-7/8" x 2"
1.562 .937 3" x 2-1/81t
1. 750
1.000 3-1/411 x 2-1/8"
2.000 1.1875 3-3/8 1t x 2-1/4"
2.125 1.375 3-13/16 11

x
2-1/211
2.250 1.750 3-3/4" x 2-3/4"
2.250 1. 750 3-3/411 x 2-3/411
~
::u
::u
n
A
(J)
2-7/16" 2-11/16 11 x x 1-13/16" 1-7/8"
::u
()
2-5/8" 28" 20 4 2 to 3 0 17/32' 2-5/8" 28" 20 40 2 to 3 0 2-17132" 2_5/8" 2-29/32" 28-1/16" 3T':':7/8" 1 40 2 to 3 0 2-1/ 2" 1 4 2 to 3 0
0
[Tl
<
2-29/3211 31-7/8" 1 40 2 to 3
0
3-1/411 31-718" 1 40 2 to 3 0 0
4-1/16 11 31-1/8" 1
40
2 to 3 0
0
4-9/3211 31-1/8" 10 40
2 to 3 0
4-27132" 4-27132" 31-118 11 31-118" 10 4

2 to 3 0
[Tl
10 4
2 to 3 0
s:
z
c
r
118 to
3/16 11
1/8 to 3116"
1/16 to 1/8"
III 6 to 1/8"
1116 to 1/8 11
III 6 to 1/8"
III 6 to 118"
1116 to 1/8"
1/16 to 1/8"
1/16 to 1/8 11
AXLE-FRONT Section A Page 1
FRONT AXLES
F160, F-170
steering Knuckle Pins and Bearings
(See Figs. 1 and 2)
Steering knuckle thrus t bearings, located between knuckles and lower faces of I-beam, support the entire front end load. The end play must be kept within proper limits to prevent excessive wear. The use of spacing washers to correct this condition is described in sub sequent paragraphs. A tapered draw key with nut and lockwasher hold knuckle pin rigidly in end of I-beam. The draw keys should be inspected occa sionally to assure their being tight. 1 one becomes loosened, knuckle pin hole as well as draw key hole will become worn and necessitate replacing or machining of I-beam. Steering knuckle pins and bushings are available in sets to facilitate replacement service. Oversize steering knuckle pins are avail able for use if the I-beam hole has been worn. Installation of oversize pins necessitate ream ing hole in the I-beam and bushings to the new diameter. Bronze bushings are used in steering knuckle at upper and lower knuckle pin holes. Seals at top and bottom consist of expansion plugs pressed into steering knuckle. Removal of expansion plugs can be readily accomplished by drilling a 174" hole through one of the plugs. Remove knuckle pin draw key. Insert a punch in hole in expansion plug and drive pin against opposite plug, forcing it from its recess. Reverse direction of pin trav el and force out drilled expansion plug.
Shock absorber
Expansion plug
Steering knuckle
A-22487
Fig. 2,
Refitting Steering Knuckle Pin Bushings

After ascertaining that steering knuckle bushings require replacement, the following procedure will be found efficient and helpful: For service stations doing a large volume of steering knuckle bushing service work, there is a special set of installing arbors and burnishing tools available. Reamers are not necessary with this equipment. 1. Remove hub caps and grease caps. 2. Remove spindle nut cotter keys and spindle nuts. 3. Remove wheels, inner bearings, and grease retainers from spindles. 4. Remove dirt shield screws and shields. 5. Remove bolts holding brake backing plate assemblies to steering knuckles. Lay assemblies back over ends of axle I-beams. 6. Remove tapered draw keys holding knuckle pins.
~~""':::"-r-- King pin
A-22203
7. Remove expansion plugs f:rom top and bot tom of steering knuckles. 8. Drive out knuckle pins.
Fig. I
PRINT[O IN UNITED STATES Of' """ERICA
9. Remove steering knuckles, thrus t bearings, and any spacer shims present.
10. Clean all parts thoroughly in kerosene or Stoddard Solvent.
11. Remove old bushings, using an arbor or drift. 12. Install new bushings, with the grease holes lined up with the lubricating holes in the steering knuckles. Use an arbor press or vise for forcing the new bushings into place, piloting with a proper size arbor. 13. Line-ream new bushings. Use either special burnishing equipment or a reamer equipped to pilot in one bushing while reaming the other or a reamer long enough to ream both bushings at the same time.
Ball
seat
A-22204
Fig. 3 - Details of tie rod end.
Tie od (Fig. 3) R
Tie rod is of three-piece construction, consisting of two rod end assemblies. Rod is threaded into ends and locked with clamp bolts. Right and left-hand threads are provided to facilitate toe-in adjustment. The rod ends are self-adjusting and require no attention in serv ice other than periodic lubrication and occa sional inspection to see that ball studs are tight in steering knuckle arms. Proper adjustment can be effected by:
14. Install steering knuckles, thrust bearings, spacer shims as required, and knuckle pins.
15. Install knuckle pin draw key and tighten securely. NOTE: Draw key nut and lock washer should be located on front side of axle.
16. Insert expansion plugs in top and bottom of steering kn\lckles. Expand into recess by striking with a hammer. 17. Place brake backing plates in position and install bolts. Tighten bolts securely. 18. Install dirt shields and holding screws. 19. Clean and repack front wheel bearings. 20. Install new grease seals.
1. Remove cotter key. 2. Tighten adjusting plug until it "bottoms" or is snug. 3. Loosen adjusting plug to the nearest cotter keyhole (not over 1/4 turn). 4. Install new cotter key. NOTE: Always check and correct toe-in of front wheels after any adjustment of tie-rod ends.
21. Install wheels and spindle nuts. Rotate wheel by hand while tightening nut until drag or bind is felt. Back off nut to first cas tellation and ins tall ~ cotter key.
22. Install grease caps and hUb caps. 23. Lubricate steering knuckle bushings. 24. Check and correct toe-in of wheels.
Front Wheel Alignment

Front wheels mustbe kept inproper align':' ment in order to assure ease of steering and satisfactory tire life. Important factors of front wheel alignment are: Toe-in, camber and axle caster. These points should be checked occa sionally to guard against excessive tire wear.
Steering Knuckle Stop Screws

Adjustable stop screws in steering knuckle limit movement of front wheels when turning and prevent tires from rubbing against nearest point on chassis and to prevent steering gear from bottoming. These screws should be ad justed so there will be ample clearance between front tires and nearest point on chassis when wheels are turned to extreme right or left under any conditions. NOTE: This should be checked when tire size is changed.
Wheel Toe-In (Fig. 4)

Front-wheel toe-in is the setting of front wheels so that they are closer together at the front of the axle than at the rear. Incorrect toe-in of front wheels will result in ra~id tire wear. Excessive toe-in will pro duce a scuffing or "feather-edge" at the inside edge of the tire tread. Toe-out will produce a like wear but at the outside of the tire tread.
C
r
"""
~
f-.
~-
TREAD
"Positive" camber is an outward tilt or inclination of the wheel at the top. "Negative" or "reverse" camber is an ward tilt of the wheel at the top.
BI
f,OF STEERING ARM BALL ,..~

IJ
Axle Caster (Fig. 6)

Caster is the amount of backward tilt at the top of the steering knuckle pin. When the top of the knuckle pin is tilted to the rear, the caster is positive. When the top of the knuckle pin is tilted to the front, the caster is negative. The purpose of caster is to provide stabil ity of steering.
I
,
,
1\T
,
./
I
"- ./
~D~TO~KING PI~! '

M
Fig.
It
'\<tOF AXLE~
A-22202
G- CASTER
ANGLE
Follow instructions of Tool Equipment Manufacturer for checking and correction of toe-in. NOTE: Always recheck toe-in after any change in caster or camber angles, or after any alteration in tie-rod end adjustment.
Wheel Camber (Fig. 5)

Front-wheel camber is the inclination of the wheel from a vertical plane.
4 OF
KING PIN VERTICAL LINE
A-22199
E -CAM BE.R ANGLE.

VERTICAL LINE
Fig. 6
1jF- KING PIN INCLINATION

"
-e-----r-'
'LEVEL OF <t SPRING PAD STEERI NG ARM BALL
Tapered wedge plates are available for use in altering the caster angle. They are to be installed between the springs and axle spring seats. Installation with the thick end toward the rear will produce increased caster. If in s talled with thick end toward the front, will decrease caster.
iHoFTIRE
Fig. 5
F>RINTEO IN UNITEO STATES OF' AMERICA
Knuckle Pin Inclination (Fig. 5)

A-22200
The angle which the kingpin makes with the vertical is known as kingpin inclination.
AXLE-FRONT Section B Page 1
FRONT AXLES
F-270, F-280, F-360, f-580, F-553, F-653, F-750, F-751
Steering Knuckle Pins and Bearings (See Figs. 1 and 2)
Steering knuckle thrust bearings, located between knuckles and lower faces of I-beam, support the entire front end load. The end play must be kept within proper limits to prevent excessive wear. The use of spacing washers to correct this condition is described in sub sequent paragraphs. A tapered draw key with nut and lockwasher hold knuckle pin rigidly in end of I-beam. The draw keys should be inspected occa sionally to assure their being tight. If one be comes loosened, knuckle pin hole as well as draw key hole will become worn and necessitate replacing of I-beam. Steering knuckle pins and bushings are available in sets to facilitate replacement service. Bronze bushings are used in steering knuckle at upper and lower knuckle pin holes. Seals at top and bottom consist of gasket and plate, held in position by flat head screws and lockwashers.
Spacing washer
Fig. 2 - Showing details of relay lever, relay I ink and drag I ink.
2. Remove spindle nut cotter keys and spindle nuts. 3, Remove wheels, inner bearings, grease retainers from spindles. and
4. Remove dirt shield screws and shields. 5. Remove bolts holding brake backing plate assemblies to steering knuckles. 6. Remove tapered draw keys holding knuckle pins. 7. Remove caps from top and bottom of steer ing knuckles.
A22542
Fig. I
Refitting Steering Knuckle Pin Bushings
For service stations doing a large volume of steering knuckle bushing service work, there is a special set of installing arbors and bur nishing tools available. Reamers are not nec essary with this equipment. After ascertaining that steering knuckle bushings require replacement, the following procedure will be found efficient and helpful:
8. Drive out knuckle pins. 9. Remove steering knuckles, thrustbearings, and spacer shims. 10. Glean all parts thoroughly in kerosene or Stoddard Solvent. 11. Remove old bushings, using an arbor or drift. 12. Install new bushings, with the grease holes lined up with the lubricating holes in the steering knuckles. Use an arbor press or vise for forcing the new bUShings into place, piloting with a proper size arbor.
1.
Remove hub caps and grease caps.

PRINTEO IN UI'(ITO 5TA,TES OF' AMERICA

20. Install new grease seals. 21. Install wheels, and spindle nuts. Rotate wheel by hand while tightening nut until drag or bind is felt. Back off nut to first castellation and install new cotter key. 22. Install grease caps and hub caps. 23. Lubricate steering knuckle bushings.
13. Line-ream new bushings. Use either a reamer equipped to pilot in one bushing while reaming the other or a reamer long enough to ream both bushings at the same time. 14. Ins tall steering knuckles. thrus t bearings, spacer shims as required, and knuckle pins. 15. Install knuckle pin draw key and tighten securely. 16. Replace caps on top and bottom of steering knuckles. 17. Place brake backing plates in pos ition and install bolts. Tighten bolts securely. 18. Install dirt shields and holding screws. 19. Clean and repack front wheel bearings.
24. Check and correct toe-in of wheels.
Steering Knuckle Stop Screws

Adjustable stop screws in steering knuckles limit movement of front wheels when turning and prevent tires from rubbing against nearest point on chassis and prevent steering gear from bottoming. These screws should be adjusted so there will be ample clearance between front tires and nearest point on chassis when wheels
_ - - - - Lubricator
Relay lever J..iF.-"-----Relay lever bracket and shaft assembly Relay link stud ball Frame side rail
Drag link stud ball
Lubricator --lIo-<!
Steering gear arm
Lubricators
Drag link
A21748
Fig. 3 - Front axle linkage and steering gear for L-190 Series and up.

are turned to extreme right or left under any conditions. NOTE: This should always be checked when tire size is changed.
satisfactory tire life. Important factors of front wheel alignment are: Toe-in, camber and axle caster. These points should be checked occasion ally to guard against excessive tire wear.
Linkage for Models L-190 and Up (Figs. 2 and 3)

Figs. 2 and 3 illustrate front axle linkage with the steering gear for models L-l90 series and up. In order to maintain the proper degree of angle on steering column for best riding and driving comfort, the relay lever assembly is used.
C N
TREAD
Tie Rod (Figs. 4 and 5)

Tie rod is of three-piece construction, consisting of two rod end assemblies and tube. Rod is threaded into ends and locked with clamp bolts. Right and left-hand threads are provided to facilitate toe-in adjustment. The rod ends are self-adjusting and requir.e no attention in service other than periodic lubrication and occasional inspection to see that ball studs are tight in steering knuckle arms.
r .......
,...
~
I--
T\
B If~OF STEERI 'JG ARM BA Ll r--~ hi ,. '
"'"
..
'
TI
"- l/
Cover
I ,
'\q;OF AXLE
~D<tTO<tKING PI~ ' ./

M
Fig. 6
I
Felt
Wedge....",.-~~--t
A-22202
Wheel Toe-In (Fig. 6)

Fig. ij F-360.
-
BaD seat Tie rod assembly-Models F-270, F-280,

A22528
Front-wheel toe-in is the setting of front wheels so that they are closer together at the front of the axle than at the rear. Incorrect toe-in of front wheels will re sult in rapid tire wear. Excessive toe-in will produce a scuffing or IIfeather-edge" at the in side edge of the tire tread. Toe-out will pro duce a like wear but at the outside of the tire tread. Follow instructions of Tool Equipment Manufacturer for checking and correction of toe-in.
~-~
Tie rod end
Washer
Spring
Cover
A22551
NOTE: Always recheck toe-in ~ any change in caster or camber angles, or after any alteration in tie-rod end adjustment.
Fig. 5 - Tie rod assembly - Models F-553, F-580, F-653, F-750, F-751.
Wheel Camber (Fig. 7)

Front-wheel camber is the inclination of the wheel from a vertical plane. "Positive" camber is an outward tilt or in clination of the wheel at the top.
Front Wheel Alignment

Frontwheels must be keptin proper align ment in order to assure ease of steering and
PRINTED IN UNITD STATES OF' AMERICA
LLINE MOTOR TRUCK SERV1CE MANUAL
"Negative" or "reverse" camber is an

ward tilt of the wheel at the top.
~r-G-CASTER
_____T-'__
Axle Caster (Fig. 8)

Caster is the amount of backward tilt at the top of the steering knuckle kingpin. When the top of the knuckle pin is tilted to the rear, the caster is positive. When the top of the knuckle pin is tilted to the front, the caster is negative. The purpose of caster is to provide sta bility of steering. Tapered wedge plates are available for use in altering the caster angle. They are to be installed between the springs and axle spring seats. Installation of the tapered wedge with the thick end toward the rear will produce increased caster. If installed with thick end toward the 'front, decreased caster will result.
ANGLE
4 OF
KING PIN
Fig. 8
TAPERED WEDGE VERTICAL LINE

A-22199
Knuckle Pin Inclination (Fig. 7)

The angle which the kingpin makes with the vertical is known as kingpin inclination.
E -CAMBE.R ANGLE.
VERTICAL LINE
1jF- KING PIN INCLINATION

'. [A
'LEVEL OF <t SPRING PAD STEERING ARM BALL
OF TIRE
Fig. 7
A22200
AXLE-FRONT Section C Page I
SUGGESTED WHEEL ALIGNMENT TROUBLE SHOOTING CHART
Remember that all alignment angles are so closely related that any change of one will auto matically change the others. Because of this fact, it will probably be found that there is more than one cause for the complaint. The following list is not all-encompassing but is representative of the more common causes of difficulty en countered in wheel and axle alignment and should prove of value in locating and correcting com plaints on steering or tire wear,
COMPLAINT
(1)
POSSIBLE CAUSE
(a) Tire pressure incorrect.
(b) Tires of unequal size or weight.
(c) Wheel bearings loose.
(d) Steering arms loose.
(e) Steering gear loose.
ef) Too much caster.
(g) Drag link ends loose.
(h) Drag link springs weak or broken.
(i ) Spring shackles loose.
(j) Kingpins and bushings worn.
(k) Tie-rod ends loose.
(a) (b) (a) (b) (c)
Tire and wheel assemblies out of balance. Shock absorbers ineffective. Tire pressure incorrect. Tires of unequal size. Bent spindle. Wheel bearings loose. Kingpins and bushings worn. Kingpins bent. Kingpins tight. Pitman arm loose. Steering gear assembly too tight or too loose. Too little caster. Too much or too little camber. Too much or too little toe-in. Drag link ends tight. Drag link springs weak or broken. Tie-rod ends too tight or too loose. Front axle bent. Front axle shifted. Springs broken. Rear axle shifted. Rear axle housing bent. Frame diamond-shaped. Tire pressure low. Wheel spindle bent. Kingpin assembly poor fit. Steering assembly too tight. Tie-rod ends tight. Gaster excessive. Tire pressure low. Excessive camber. Wheels out of balance. Tires overloaded. Eccentric wheels or rims. Gaster incorrect. Toe-in incorrect.
Shimmy
(Generally exists at speeds below 30 miles per hour.)
(2)
High-Speed Wheel Tramp

(Generally xists at speeds above e 35 miles per hour.)
(3)
Wander or Weave
(d) (e) (f) (g) (h) (i) (j) (k) (1 )

(n) (0) (p) (q) (1' ) (s) (t) (u)
(m)
(4) Hard Steering
(a) (b) (c) (d) (e) (f) (a) (b) (c) (d) (e) (f) (g)
(5) Uneven Tire Wea,r
PRINTED IN UNITED STATES OF AM[FlICA
a
~ '" ~
II
Ell
REAR AXLE APPLICATION AND LUBRICATION CAPACITIES (R- LINE TRUCKS)
MANUFACTURER'S
IH MODEL
NUMBER ENGINEERING NUMBER
HYD. 1401 1402 1403 1404 1405 1406 1409. 1410 1411 1412 1415 1416 l41S 1420 1423 R-I060 R-1070
--_.
" " ;
~
CODE
DESCRIPTION
TRUCK MODELS
" :: !l
~
AIR
HYD. IH IH IH IH IH
AIR
Single Reduction Single Reduction Single Reduction Single Reduction Single Reduction Single Reduction T-R-I00 Single Reduction Eaton Two Speed Eaton Two Speed E-16600 E-2614 E-2696 E-20501 Eaton Two Speed Eaton Double Reduction Eaton Double Reduction Eaton Two Speed R-II0 R-120, RM-120, RA-120 RA-140, R-150, 153, RM-150 R-160, 163, 165, RC-160 R-164, 170, 173, 175 R-174 Hydraulic, R-lS0, R-lS3, lS5, lS53, RC-lS0 R-194, 200, 201, 202, 205 R-160, 163, 165, RC-160" R-164, 170, 173, 175 R-174, Hydraulic, R-lS0, R-18.3, lS5, lS53, RC-lS0 R-lS4, 190, 193, 195 R-194, 200, 205 R-190, 200 R-210 R-210
LUB. CAPACITY (PINTS) 4
~ -
---4
5 S
R-1170 R-1440 R-1470 R-1530 R-1740 R-2464 R-2467 R-25S5 R-1540 R-1640 R-27S0 R-1S10 R-2800 R-25S6 R-154l R-164l R-27S1 R-lSll R-2S01 R-1531 R-1741
[Tl
2t
a
11 36 13 13 , 16 19 19 20 3S 37
'0
S:'
IH T-R-I00 E-13600 E-13600 E-16600 E-2613 E-2695 E-20500 T-U-200P T-U -300P
~.
~
()
"
c:
tn
?\
T-U -200P Timken Double Reduction T-U -300P Timken Two Speed
~><
~.
~n
CIl
I
~tz:1
t'
~
u III
: ::! tz:1
(1)g
.... rn~
REAR AXLE APPLICATION AND LUBRICATION CAPACITIES - Continued , (R- LINE TRUCKS)
IH MODEL ENGINEERING NUMBER HYD. 1425 1426 1428 1429 1430 1433 1435 1436 1438 1450 1451 1452 1453 1454 1455 1456 1457 1458 1459 R-2575 R-2620 R-2366 R-1572 R-1632 R-1573 R-1633 R-1470 R-2466 RF-1570 R-2576 R-2621 E-17500 E-18500 E-1350 E-1790 E-1890 E-1791 E-1891 R-2470 R-2475 RF-1475 RF-1575 RF-1685 R-1l65 R-2610 R-1547 R-2995 R-2795 R-2611 R-1548 R-2996 R-2796 RF-1690 IH E-13600 E-28M E-1750l E-1850l E-22M E-22M E-36M IH TQ-301N TL-101 TL-301 TR-300 TQ-301P TL-101 TL-301 TR-300 E-36M AIR MANUFACTURER'S NUMBER HYD, AIR IH Two Speed With Tim.ken E300 Differential IH Two Speed With Tim.ken E300 Differential IH Single Reduction Eaton Single Reduction Eaton Single Reduction IH Single Reduction Tim.ken Two Speed Tim.ken Single Reduction Tim.ken Two Speed Tim.ken Two Speed Eaton Single Reduction IH Single Reduction Ea ton Two Speed Eaton Single Reduction Eaton Two Speed Eaton Two Speed Eaton Two Speed Eaton Single Reduction Eaton Single Reduction R-160, 163, 165 R-164. 170, 173, 175 RF-170 RF-174, 190 RF-194, 210 R-130 R-194, 200, 205 R-190, 193, 195 R-184, 190, 195 R-200 RF-194,2l0 R-164, 170, 173, 175 R-164, 170, 173, 175 RF-174, 190 R-184, 190, 193, 195 R-194, 200, 205 R-150, 153 R-184, 190, 193, 195 R-194, 200, 205 LUB. CAPACITY (PINTS) 8
'tI uql"
()Q~ .....
~
PI 'tl
0
><
L
N::::OO
CODE
DESCRIPTION
TRUCK MODELS
..'tzJ o I e:.~ "'tzJ
g>
UI~
8
11 ea, axle 14 ea. axle 20 Forward 21 Rear 6 32 23 29 34 20 Forward 21 Rear 8 11 14 ea. axle 17 16 13 22 21
trl
3:
~ ~
;;3 c n
~ Ul
~
~
Ell
AXLE-REAR
Index
Page 1
REAR AXLE GROUP

SPECIFICATlONS
Axle identification chart
Specifications . . . . .
Wrench torque chart . .
Page
1
2-5
6
SECTION "A"
GENERAL INSTRUCTIONS FOR ALL HYPOID AXLES:
Axle housing breather . . . . . . . . . . .
Axle shaft removal. . . . . . . . . . ......
Cone center specifications. . . . . . . ..
Differential assembly (L-llO, L-l20). . , ....
Gear adjus tmen t for lash. . . . .
Gear tooth contact ......
Hypoid rear axles. . . . ...
Lubrication . . . . . . . . . , . . . . .
Pinion bearing adjustment . . . . . . . . . .
Pinion setting . . . .. . . . . . . . . . . .
Ring gear rivets . . . . . . . . . . . . .
Single reduction axles - - sec tional views .
Straddle mounted pinion bearing . . . . .
9
8, 9
I, 2
10
5, 6
1
1
9, 10
6, 7
2, 3, 4
7, 8
11, 12
7
SECTION liB"
TWO-SPEED AXLE -- EATON
Des cription. . . . . . . . . .
Lubrication. . . . . . . .
Sectional view . . . . .
Servicing and disassembly. . . . .
2
3
1
2, 3
SECTION "C"
DOUBLE-REDUCTION AXLE -- EATON Description . . . . . . . . . . . . , . . . . . . Differential lubricators. . . . . . . . Herringbone gear adjus trnent . . . . . . Herringbone gear shaft (cross-shaft). Hypoid pinion shaft and adjustment Sec tional view. . . . . . . . . . . 2
3
2
2
2
1
SECTION "D"
SINGLE-REDUCTION AXLE -- TIMKEN Description . . . . . . . . . . . . . . Differential carrier bearing pre-load. Differential disassembly. Gear adjus tmen t. . . . . . Lubrication . . . . . . . Pinion bearing pre-load. . . Sec tional view . . . . . Thrus t block ins tallation . . .
Z 4
2, 3
4
5
3" I
SECTION "E"
DOUBLE-REDUCTION, TWO-SPEED -- TIMKEN Description . . . . . . . . . Differential adjus trnent . Electric two-speed shift Hypoid pinion and cage . Lubrication . . . . . . . . . Shift collar adjus tment .
PRINTED iN UNITED STATES OF AMeRle ...
4
3
2, 3
4
3
AXLE-REAR Index Page 2

SECTION "Fit
Page
DOUBLE-REDUCTION -- TIMKEN Description . . . . . . , Helical gear shaft (cross shaft), . Hypoid pinion and cage . . Lubrication. , Oil seals . . . , , , . . .
I
3
3
3
2
SECTION "G"
TANDEM AXLES Center cross bar and equalizing beam mounting. Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Di'ferential lock. . . . . . . . . ,
Disassembly of power divider (axle mounted) ..
Equalizing beam ends. , , . . . . . . . .
Legends for sectional view. . . . . . . . . .
Sectional view (axle mounted power divider) . ,
Torque rod ends . . . . . . . . . . . . . . . . . . . . . . . . . . .
I
2
3,4 4. 5
2
I
SECTION "H"
ELECTRIC SHIFT Axle shift unit . . . , . , . Axle unit disassembly . . . . . Des cription . . . . : . Lubrication . . . . . . Par ts identification lis t. . . . . . . Service and trouble-shooting .. Shifting ins tructions . Speedometer adapter .. Wiring system . . . .
2, 3
4-7
1, 2
4
3,4
7
2
2
REAR AXLE IDENTIFICATION CHART
Axle Axle Code Model Nwnber Nwnber
DESCRIPTION
~ 0' O~ o~ 0 ~ 0 M to 0 M ~ U') >.00 M~ ...... M~ U') COo M o U') No M ...... N , M ...... to U') ,>.0 >.0 >.0 >.0 ..... r- r-r- ~ """0 coco co ...... 0' 0' ~~ ..... ...... 0 0 tOO ~ N NN NM N ON ...... ..... ...... ..... ..... co ............ ...... ...... ...... ...... ...... ...... ...... ...... ...... I NN N ' NN IN I
...... , I 1 , I -;'~ I I!l 1 1 ~-;' 1 I 1 UI I I Pt!1 I UI I ..... I U I 1 IU ~ I I Pt!1 ...:I ...:1...:1 ...:I ...:I ...:I ...:I ...:1...:1 ...:I ...:I ...:I ...:1...:1 ...:1...:1 ...:I ...:1...:1 ...:1...:1 ...:l ...:1...:1 ...:I ...:I ...: ...:I Pt! ...:1...:1 ...:1...:1 ~ .... ...:1...:1 ...:1...:1 Pt! ...:I ...:I ...:I
0
'
::
1401 __ R-1060 Single-ReduCtion-IH . . ~ ... - ' 1402 R-I070 Single - Reduction-IH. . XX .. :- 1403 R-1l70 ~!!!gle-Recluction-IHo . X X X X 1404__ .&-}440 ~ Sinde-Reduction-IH X X XX R-1470 SinKle-Reduction-IH 1405 X X X X R-1530 Single-Reduction-IH 1406 X 1407 R-1555 Sin~-.Reductio~n . 1408 R-1630 Single -Reduc Hon -Ea ton ~.09 R-1741 Sing!E):~educ tion- Tirnken R-2465 Tw<?~~.ed-:~a.~on_._._~~.~~~. 1410 XX XX 1411 Two-Speed-Eaton X X X X l- 1412 R-2466 Two-S:eeed-Eaton . ~. R-2585 X R-2580 ~~p!:~.<i-E~ton . 1413 1414 R-2000- Two-Speed-Eaton !--- 1415 R-1540 Doub1e-Reduction-Eaton. -- R:'-1640 DoulJ1e-Recl_~_H<:>n-Eat0!1...!. 1416 -- --,f - - !--- f'" 1417 1418 R-1731 Douh1e-Reduction1419 Tirnken . . . R-1810 Doub1e-Reduction1420 Tirnken ,J1~L~_ R~1140 ~l1gle-Reduction,::.Tirnken 1422 R-2741 Two-Speed-Tirnken l- R'::Z800 ~Speed- Tirnken . 1423 ---1424----1425 R-2470 Two-Speed with Tirnken
~:---!'--~~ ~~~
~.
~~
X X X
X X XX X X X
X
l -I -
- I--
X
l - I---
[TJ
t z
$
-~-
o :;0
o
C
~
:;0
~~
X X X
------
XX XX X X XX X X X
.~~
-;
A
:;0
XX X X
f- 1-"
i-- !------
I~~-
f-- I-
~~-
----
I-~
UJ
--~
[TJ
~~~-
~~
~~.
X XX
I~~~-
n
[TJ
<
-~
t- I-
t-~
X X
-------------
z c
r
i-
Di.f.f.
10
* ..............
~~~
R-2-'!'75 Two':"Speed with Tirnken i=-~ Difh...!_L~. .

1427 ~ R:'::Z590- Two-Speed with Tirnken
~~-
l-II - I",
,0
----
Dirf.
'0
RF-1475 Single -Reduc tion::IH. _____. 1428 ---RF'::Ts75 ~~!!g!e::~~dt1c~~on-IH 1429 RF-1685 ~_~!!gle-Reduction-~_~ton. 1430 1431 -- 1432 1433 R1l65 Single-Reduction-IH. :-:.
I'"
,-
~~
- ----
~>
X
~
'--
I- -
C'
i-- i--
I~~~
-~
I-~
!--- I-
- - I
'---
\:!!tzl ItJ (") I III III ):tJ OQ po: 1.'1

~
-
P. ~
g >
UI
):tJ
REAR AXLE SPECIFICATIONS

- . - . - ................
~-
------
~--
--
:root:"' ~ ><
N ....
'tJUl)
RF-1475 REAR AXLE MODEL R-I060 R-I070 R-1165 R-1l70 R-1440

R-1470
Forward RF-1476 1428 Full Overhung
---
~M
p.>:;l:I
Rear RF-1477 1428 Full Straddled
0) ~:;l:I
p:M
Code . . . . . . . . . . . . . . Type (Semi or Full-Floating). Pinion Mounting . . . . . Axle Shaft: Diameter at splines . . . Number of splines . . Pinion Cone Center (amount of variation marked on pinion). Lubricant Capacity (Pints) . Axle Ratios . . . . . . .
1401 Semi Straddled
1402 Full Straddled
1433 Full Straddled
1403
Full Straddled
1404
Full
Str-addled
1405
Full
Straddled
[Tl
t z
1-9/32" 10
1-9/32 11 10
1-33/64" 16
1-33/64" 16
1-3/4" 16
1-3/411 16
1-3/411 16
1-3/411 16
:;0 :;0
(')
--l
2.609 4 3.73 4.1
2.609 4 4.1 4.777 5.13
2.984 4 4.88 5.571 6.166
2.984 3 4.88 5.57 6.16
3.253 8 5.285 6.166 6.666 7.166
3.253 8 6.166 6.666 7.166
4.156 8-Axle 3-P.D. 6.166 7.166
3.253 8 6.166 7.166
C
A
(J)
[Tl
:;0
(') [Tl
<
Pinion Adjus trnent: Press pressure (tons)* . . . Cage Rotating Torque Scale Reading (Lbs.) . . . . . . Pinion Nut Torque (Ft. Lbs.) .
10
10
10
10
10
10
10
10
z
c
10-25 200-230
10-25 200-230
10-25 200-230
10-25 200-230
10-25 200-230
10-25 280-300
10-25 350-400
10-25 280-300
Differential Bearing Pre-load. (Total). . . . . . . . .005 11 -.007"

---
005"-. 007" .005" -.007 11 .005"-.007 11 005" -. 007" .005" -.007 11 .005" -.007" .005 11-.007 11
----~
---
............
-.---
...........- -
* Pressure against bearing race when checking rotating
torque of pinion cage.
RF-1575 REAR AXLE MODEL R-1530 R-1540 R-1555 Forward RF-1576 Code . . . . . . . . Type (Semi or Full-Floating). Pinion Mounting . . . Axle Shaft: Diameter at splines . . . Number of splines . . . . . Pinion Cone Center (amount of variation marked on pinion). Lubricant Capacity (Pints) . . Axle Ratios . . . 1-7/8f! 16 1-63/6411 16 1-63/6411 16 1-3/411 16 1-3/41! 16 2-1/8 11 16 2-1/8 16 2-1/8" 16 1406 Full Straddled 1415 Full Overhung 1407 Full Straddled 1429 Full Overhung Rear RF-1577 1429 Full Straddled Forward RF-1686 1430 Full Overhung Rear
RF-1687
-----
RF-1685 R-1630
1430
Full
Overhung
1408
Full
Straddled
[l1
$:
o -1 o :;0
-1
()
:;0
3.472
II
2.500 19 7.049 7.754 9.025
3.844 20 5.571 6.5 7.166
4.656 12-Axle 3-P.D. 6.166 7.166
3.473 12 6.166 7.166
4.875 20-Axle 3-P.D. 5,756 6.940
4.875 21 5.756 6.940
2.937 18 5.571 6.5 7.166
A
fJ)
[l1
:;0
5.571 6.5 7.166
n
[l1
<
$:
Pinion Adjus trnent: Press pressure (tons)* . . Cage Rotating Torque Scale Reading (Lbs.) . . . . Pinion Nut Torque . .
z
c
10
10
------------
10
10
10
10
10
----------
10
r
en
10-25
280-300
10-25
280-300
10-25 350-400
10-25
350-400
10-25
280-300
10-25
600-900
10-25 400-500
10-25 350-400
Differential Bearing Pre-load. (Total) . . . . . . .005" -. 007" .005" -.007" .005" -.007" .005"-.007" . 005" -.007" 005" -. 007" .005" -.007" 005" -,007"
:~~
III I
'U'tl
>
(l)!::;t" I.~M
p:~
Pressure against bearing race when checking rotating torque of pinion cage,
::s>
(f)~
oM

-----
Jg ~ ~
~ n
"tI
CIl
>
REAR AXLE MODEL Code . . . . . . . . . . Type (Semi or Full-Floating) . . Pinion Mounting . . . . Axle Shaft: Diameter at splines . . . Number of splines . . . . Pinion Cone Centers (amount of variation marked on pinion). Lubricant Capacity (Pints) . Axle Ratios . . .
R-1640 1416 Full Overhung

R-1730
.. D .. .. ..
R-1740 1421 Full Straddled
R-2466
R-2470 1425
-
t"' ~S!M n I 1lll:t1
1411
Full Overhung
g.~
~ l:t1
Full Overhung
Full Overhung
r.
2-1/8 11 16 2-3/8 11 16 2-3/8 11 16 2-3/8 11 16 2-3/8 11 16 1-3/4" 16 1-3/4" 16 1-3/411 16
z [TJ
$:
-l
2.625 19 7.049 7.754 9.436
. .
.. .. ..
. .. ..
. . ..
.. .. .. .. .. .. .. .. .. . . . .. . .. .. .. .
36 5.28 6.83 7.41 38 5.91 6.51 7.21 7.79 9.76
4.281
4.281
. .. .. . . . . ..
:;;0
o
C
38 5.91 6.51 7.79 8.69 9.76
38 5.91 6.51 7.79 8.69 9.76
13
5.14-7.15 5.83-8.11 6.33-8.81
13
5.l4-7.l5 5.83-8.11 6.33-8.81
.. . .
. .. .. .
;j
()
6.13-8.10 6.70-8.86
A
tn
()
[TJ
<
Pinion Adjus tment: Press pressure (tons)* . Cage Rotating Torque Scale Reading (Lbs.) . . . . Pinion Nut Torque (Ft. Lbs.)
10
10
10
10
10
10
10
.. . .. ..
,.
.. . .
$:
z r
c
10-25 400-500
4-5 &: 700-900
4-5 &: 700-900
4-5, &: 700-900
4-5 &: 700-900
10-25 280-300
10-25 280-300
. .. . .
. .
..
. ..
.. .
. .. . . ..
Differential Bearing Pre-load. (Total) . . . . . . . . . . .005"-.007"

-
See Note
See Note
See Note
See Note
005" -.007" 005" -. 007" .. .. .. .. .. . , ..

----
* Pressure against bearing race when checking rotating

&: Tirnken Axle.
torque of pinion cage.
NOTE:
Tighten one notch each from .000" end play.
REAR AXLE MODEL

Code ................... ................
R-2475 1426
---

..
R-2740
R-2741
-----
R-2800 1423
-----
. .. .. . . .
Full Overhung
1422 Full Overhung

---
Type (Semi or Full-Floating).
Full
Full Overhung
Overhung Pinion Mounting . . . . . . . Axle Shaft: Diameter at splines . . . . Number of splines . . Pinion Cone Centers (amount of variation marked on pinion). . . Lubricant Capacity (Pints)
"
I
1-3/411 16 1-63/6411 16 1-7/8 11 16 1-7/8 11 16 2-1/8 11 16
-----
[l1
2-3/8 11 16
2-3/8 11 16
2-3/8 11 16
o --l o ;0
;0
()
~
fJ)
3:
. . .. .. ..
5.281 22
4.B12 20
.. .
.. .. .. .. ..
5.281 22
.. ..
.. .. ..
. .. ................
37 4.93-5.<:1 6.42-8.38 6.99-8.38
--l
..
. .. .. . .. .
37
. .. .. . .. ..
. .. .. .. .. .. . ..
37
---
---6.13-B.I0 Axle Ratios . . . . . . 6.70-8.86 5.571-7.594 5.571-7.749 6.5-B.B66 6.166-8.577 6.5-9.041

-----
5,95-7.30 5.571-7,594 6.13-B.15 6.500-8.866 6.66-8.85
4.93-5,91 6.42-8,38 6.99-8,38
4.93-5.91 6.42-8.38 6.99-8.38
[l1
< n [l1
;0
Pinion Adjus trnen t: Press pressure (tons)* . . .
. .. .. . .. .. .
10
10
.. .. . . .. .. .. ..
10
25
25
25
Cage Rotating Torque Scale Reading (Lbs.) . . . . . . .. .. .. Pinion Nut Torque (Ft. Lbs.) .
. .. .. .
10-25
~--
10-25
----
. . .. .. .. . .. ..
10-25 350-400
----
4-5 &:
---
4-5 &: 800-1100
4-5 &: 800-1100
-. .. .. .. .. .. .. . .
z c r
.g>> t1I :>< 8.1:"'
'U (")
OQ
(I)
3:
350-400
280-300
---
.. .. .. .
.. ..
.. ..
BOO-IIOO
Differential Bearing Pre-load. (Total) . . . . . . . . . ..
..
. .. .. .005" -.007" .005"-,007" .. . . .. .. .. .. .. .005" -.007"
See Note
See Note
See Note
!:t!M
I
* Pressure
agains t bearing race when checking rotating torque of pinion cage. &: Tirnken Axle. NOTE: Tighten one notch each .from .000" end play.
Pl~~
\J1Ul~
g >
.....
AXLE-REAR Specifica tions Page 6
L-LlNE MOTOR TRUCK SERVICE MANUAL

B
Socket
Handle
A-22879
FT. LBS. WRENCH

EFFORT ON WRENCH
(APPROX.)
TORQUE A
B
200 1 foot 2 feet 1-1/2 feet 2 feet
1-I/Z feet Z feet 3 feet
200 Ibs.
1001bs.
170 Ibs.
125 Ibs.
200 Ibs. 150 1bs. 100 1bs. 175 140 118 100 180 150 129 113 1bs. Ibs. 1bs. 1bs. Ibs. 1bs. 1bs. 1bs.
250
300
350
2 feet 2-1/2 feet 3 feet 3-1/2 feet 2-1/2 feet 3 feet 3-1/2 feet 4 feet 3 feet 3-1/2 feet 4 feet 4-1/2 feet 3-1/2 feet 4 feet 4-1/2 feet 5 fee t 4 feet 4-1/2 feet 5 feet 15-1/2 feet I
450
500
167 Ibs. 1441bs. 1Z5 lbs. 112 1bs. 158 1bs. 1371bs. 123 1bs. 110 Ibs. 1501bs. 1341bs. 1Z0 Ibs. 110 1bs.
550
600
Wrench Torque Chart

The above chart illustrates the length of the wrench handle (A) and the effort that must be applied at (B) when tightening to secure the indicated torque.
AXLE-REAR Section A Page I
AXLES-REAR
GENERAL INSTRUCTIONS FOR ALL HYPOID AXLES
HYPOID REAR AXLES (ALL MODELS)

All rear axles have a hypoid :ring gear and pinion, whether single reduction, double-Teduc tion, double-reduction (single and two-speed final drive) and two-speed differential. Hypoid gears have a greater inherent torque capacity, due largely to the fact that the hypoid pinion is much larger in diameter and the pinion teeth are correspondingly larger than those found in a spiral bevel pinion for the same number of teeth and the same diameter ring gear. The hypoid pinion has a longer face because of its offset location. It also has larger tooth surface areas and usually has more teeth in ins tant contact with the gear, It is thes e design characteristics which contribute to greater strength and quieter final drive operation. Be cause of this greater tooth contact, it is more difficult to secure correct pinion setting at time of overhaul or when replacing differential bearings and every effort must be made to be sure the final setting results in best possible tooth contact, Note that the pmlOn center line (E, F) is offset from the ring gear center line (C, D).
REAR AXLE HYPOID GEAR REPLACEMENT AND ADJUSTMENT
Hypoid Gear Tooth Contact (All Models)

The proper adjustment of hypoid gears in assembly is a vital factor in obtaining quiet and durable gears and the same methods of adjust ment applies to both straight, spiral bevel and to hypoid type gears. There are two distinct considerations in obtaining the proper tooth contact, cone center and backlash. Hypoid as well as bevel and spur gears are cut with a predetermined amount of backlash. The backlash usually varies from .004" to .005" on small gears and increases on large gears. Generally, the gears are machined to run flush with each other at the outer end (heel or large end) of the tooth, and gears should be set according to their theoretical cone center (Figs. 2, 3, and 4).
Cone Center Specifications

Matched and mated hypoid ring gears and hypoid pinion gears are furnished both for service and for production. Mated gears are marked with figures showing the amount of variation from their theoretical cone center.
~~-----------D
Tbeoretical cone center of _ ' , / bevel drive gear and pinion
,F
pinion
~~~Ii!--Ilt-~ ~ ..
~.,,,
I i
A-22797
Fig. 2
A-2282B
Fig. I - Illustration shows location of pinion in relation to center 1ine of ring gear. Center line of pinion is below center line of ring gear.
NOTE: When adding to or replacing lu bricant in a rear axle having hypoid gears, use only hypoid lubricants. (See under "Lubrica tion" on page 9)
PRINTED IN UNITED STATES OF' """EAtCA
Fig. 2 illustrates a hypoid ring gear and pinion adjusted to theoretical cone center, wherein the cone centers of both gears coincide. The specifications in this case would be the distance from the line (A, B) (Fig. 1) drawn through the center of the hypoid ring gear to the ground face of the hypoid pinion on center line (E, F). On some axles, the pinion is lo cated above the center line (C, D) (Fig. 1). In these cases the term "hypoid" still applies.
AXLE-REAR Section A Page 2
center of pinion
Bracket screw
Fig. 3
Fig. 3 illustrates a setting wherein the mating of the gears has necessitated the pinion cone center being farther than the ring gear center. The pinion marking in this case will be minus (-) because the distance from the ring gear center is less.
~:M;\. eo.. _""'" ~

.
......-.:
~~- .. .. i
Fig.
~
- ;;a
..
A-22BOI
01 b"d
driv. gw
A-22494
F j g. 5
Fig. 5 shows SE-I065 tool equipment in position on hypoid differential case. Make certain that the bearing bores are clean and free of nicks or burns. The step plate must be placed on the pinion end so that the lugs in the step plate straddlt; the bearing staking in dentations on the smaller axles. 2. Install step plate and bracket as shown in Fig. 5. CAUTION: Be sure lugs on step plate straddle the bearing staking indenta tions. 3. Mount assembled SE-I065 gauge in bearing bores of carrier. 4. Take micrometer reading to check point of pinion. Add .400 11 (thickness of step plate) to reading. Write down reading. 5. Locate specified cone center specification for particular model on chart. Write down specified figures. 6. Locate on pinion the etched marking which indicates variation from zero cone center. If a minus figure, subtract from specified cone center, and if a plus figure, add to specified cone center. Results of calcula tion give corrected cone center. 7. Comparison of corrected cone center (6) with actual measurement (4) indicates amount of change necessary for pinion position. 8. Install ring gear and carrier in position. 9. Adjust backlash according to marking on ring ear.
g (See following page)
Fig. 4 illustrates a condition where the mating of the gears required the pinion cone center to be farther OUT. The pinion marking will be plus (+) because the distance is greater.
SE-1065 Pinion Setting Gauge

The SE-I065 pinion setting gauge is a pre cision gauge designed for use in adjusting differentials to the proper cone setting of the ring gear and pinion. It is used only in adjust ment of matched sets of gears. A step plate and bracket have been added to the set so that the gauge may be used on all hypoid differen tials with satisfactory results. NOTE: Be sure to allow for thickness of the step plate .400" when making calculations (Fig. 5). The use of SE-I065 gauge makes possible the exact duplication of the setting etched on the pinion. This results in the best possible setting with a minimum loss of time. It is ad visable to check all pinion settings with a paint impression before considering the work com plete. By so doing, visible proof of the pinion gauge setting accuracy is obtained, also long and quiet gear performance is assured. Adjustment of differentials is a simple matter with the SE-I065 gauge. Briefly, it is only necessary to: 1. Install pinion and bearing assembly differential carrier. in

Example of Mathematics involved; Truck model to be L-llO. (a) (b) (c) (d) Micrometer reading (add .400" for step plate) . . Specified cone center on chart . . . . . . . . . Pinion marked (-5) . . . Subtraction (b-c) gives corrected cone center. .. 3.4400" 3,400 11 .005" 3.395"
Checking tooth contact is accomplished by means of oiled red lead applied lightly to the bevel gear teeth (Fig. 6). When the pinion is rotated, the red lead is squeezed away by the contact, of the teeth, leaving bare areas the exact size, shape, and location of the contacts,
(e) Subtract corrected cone center (d) from actual measurement (a) . . . . (f) It is necessary to move pinion IN. . . . . . . . . .
.045"
(g) Remember -- It is essential to arrive at a measurement as nearly equal the corrected cone center as possible. (h) DO NOT FAIL TO VERIFY ACCURA CY OF THE ADJUSTMENT SECURED WITH THE SE-l065 gauge by checking the gear tooth contact using the paint impression method as set forth under General Rear Axle Hypoid Pinion and Ring Gear Adjustment, which follows.
Fig. 6
GENERAL REAR AXLE HYPOID PINION AND RING GEAR ADJUSTMENTS
Fig. 7
(PAINT IMPRESSION METHOD)
The following general instructions and suggestions are for the benefit of those service stations not equipped with an SE-l065 pinion setting gauge. Bear in mind that the accuracy of the adjustment obtained with the following procedure is dependent upon the skill of the operator. Hypoid gears when mounted should show a bearing toward the toe or small end of the tooth, never atthe heel or large end, the reason being that it is practically impossible to make gears and gear mounting rigid enough so that there will not be some slight deflection when fullloadis applied. This always has a tendency to caus e the bearing to come on the heel of the tooth and when gears are adjusted so that the bearing is toward the heel of the tooth it re s ults in a concentration of load on the top cor ner of the heel and breakage will follow.
Sharper impressions may be obtained by applying a small amount of resistance to the gear with a flat steel bar and using a wrench to rotate the pinion. When making adjustments, check the drive side of the bevel gear teeth. Coast side contact should be automatically corrected when drive side contact is correct. As a rule, coating about twelve teeth is suffi cient for checking purposes. With adjustments properly made, the correct tooth contact shown in Fig. 7 will be secured. The area of contact starts near the toe of the ,gear and extends about 80 per cent of the tooth length. This adjustment results in a quiet running gear and pinion set which, because the load is distributed over the te eth within the proper area, will deliver all the long service built into it. Figs. 8 to 11 illustrate method of adjust ment in securing the proper gear tooth contact.
Conlac1 adjustmnt
CONTACT 4,OJUSTMENT
Sack lash
c.orrection
B
BACK lASH
CORRECTION
A HIGH NARROW CONTACT IS NOT DESIRABLE. If gears are allowed to operate with an adjustment of this kind, noise, galling and rolling over of the top edges of the teeth will result. To obtain correct contact, move pinion toward bevel gear to lower contact area to proper location. This adjustment will decrease backlash between pinion and bevel gear teeth, which may be corrected by moving bevel gear away from pinion. Backlash of ..006" to .012" is correct.
A SHORT TOE CONTACT IS NOT DE SIRABLE. If gears are allowed to operate with an adiustment of this kind, chipping at tooth edges and excessive wear due to small contact area will result. To obtain correct contact, move bevel gear away from pinion. This will increase the length wise contad and move contact toward heel of tooth. Correct backlash of .006" to .012" can be obtained by moving pinion toward bevel gear.
Fig. 8
A15847
A-15849
Fig. 10
A
CONTACT
AOJUSTMf:NT
CONTACT ADJUSTMENT
B
BACK LASH CORRECTION
B
BACK LASH CORRECTION
A LOW NARROW CONTACT IS
NOT A. SHORT HEEL CONTACT IS NOT DE SIRABLE. If gears are allowed to operate with an adiustment of this kind, chipping, excessive wear and noise will result . To obtain correct contact, move bevel gear toward pinion to increase the lengthwjse contact and move contact toward toe. Cor rect backlash of .006" to .012" can be ob tained by moving pinion away from bevel gear. Several adiustments of both pinion and gear may be necessary before correct confact and backlash are secured.
A-15848
AJSBSO
DESIRABLE. If gears are allowed to oper ate with an adiustment of this kind, galling, noise a nd grooving of teeth will result. To obtain correct contact, move pinion away from bevel gear to raise contact area to proper location. Correct backlash of .006" to .0l2/f may be obtained by moving bevel gear toward pinion.
Fig. 9
Fig. I I

Gear Adjustment for Lash
Generally if original gears are being rein stalled, red leading of teeth will not indicate the same contact as new gears and can be mis leading. Gears that have been in service for long periods form running contacts due to wear of teeth; therefore, the original shim pack should be maintained to check gear lash. Gear lash, when using original gears, can be reduced only to a point of smooth rotation of gears.
If the gear lash is in excess of maximum tolerance as stated under Gear Adjustment, the lash may be reduced only in the amount that will avoid overlap of the worn tooth section (Fig. 12). Rotate the gears and check for smooth or rough operation. If a slight overlap, as illustrated (Fig. 12),takes place at the worn tooth section, rotation will be rough.
Fig. 13 - Checking gear lash.
Worm section of ring gear
Pinion too deep in

ring gear
Adjust Differential Bearing Pre-Load

Using dial indicators at side of each bear ing cap (Fig. 14), adjust to obtain bearing pre load as follows:
1.
Loosen adjusting nuts only enough to notice end play on indicators. Tighten adjusting nuts only enough to obtain .000" end play reading on indica tors. Note: While gear is held in ,000" end play and before loading bearings. check gear for runout. If runout exceeds .008". re move differential and check for cause,
2.
Ring gear Correct
Overlap Incorrect
A-19693
Dial indicators
Fig. 12
Fig. 12 illustrates worn condition of gear teeth and overlapping condition. When installing new gears, check gear lash with dial indicator (Fig, 13) and adjust to obtain amount of backlash marked on ring gear as follows: 1. Set pinion according to procedure outlined under SE-I065 Pinion Setting Gauge. 2. To move ring gear, tighten or loosen differential bearing adjusting nuts as re quired.
3. After correct gear lash is secured, check and adjus t as neces s ary to obtain the correct tooth contact. (See Gear Adjust ment for correct tooth contact.)
PRINTED IN UNITED STATEs OF AMERICA.
Fig. I~ - Adjusting load.
differential
bearing pre
AXLE-REAR Section A Page 6 3.

Pinion Bearing Adjustment for Pre-Load Using Dial Indicator (This method should only be used on the smaller axles).
An outside or bench assembly should be made of bevel pinion, bearings and cage. With cups assembled in cage, assemble the pinion and inner bearing cone and roller assembly in place, using the proper spacer to space the pinion bearings. Next assemble the outer pin ion bearing cone and rollers, spacer, compan ion flange, washer and nut.
Tighten BOTH adjusting nuts from .000" end play to pre-load differential bearings. Adjust pre-load to secure equal pre-load reading at indicators. (See specifications for pre-load data on the various axles.)
4. Tighten bearing cap stud nuts to specified torque. 5. Install adjusting nut locks.
Pinion Bearing Adjustment for Correct Pre-Load (Torque Method)
After the pInIon, the pInIOn bearings and spacers have been assembled in the pinion bearing cage, place the assembly in a press being sure to use a sleeve adapter as shown in Fig. 15. Press the bearing down firmly and rotate the pinion cage to align the bearings and assure normal bearing contact. Set press at correct pressure and attach a spring scale to pinion cage as indicated in Fig. 15. Read scale only while pinion cage is turning. If preload reading is incorrect, thE7 bearing load may be increased by installing a thinner spacer ot decreased by using a thicker spacer. The correct press ram pressure and scale reading for the various axles may be found in the Rear Axle Specifications.
Fig. 16
Fig. 16 shows method of attaching dial indicator when adjusting bearing pre-load. This method can be used when press equipment is not available. NOTE: Do not install pinion bearing oil seal until all adjustments have been completed. Then check bearing fit to see that bearings have no end movement with flange nut drawn up tight. To secure this fit, p'roper spacer must be found by trial as follows: (I) Place assembly in vise in position shown. (2) Mount indicator on propeller shaft flange with indicator finger resting on upper face of cage. (See A, Fig. 16.) (3) With the tips of the fingers grasp the bear ing retainer and work bearings up against the back face of pinion. (See B, Fig. l6.) (4) With the bearings held firmly against the pinion, move the cage up and down, ob serving the indicator reading. It is im possible to accurately determine the end play unless the bearing is worked loose and up against the pmIon. Assemblies having as much as .005" end play cannot be moved enough to show on the indicator until the bearing has been worked up and away from the cup. CAUTION Bearings must be absolutely clean!
Fig. 15
Fig. 15 shows method of checking pinion bearing preload using scales to measure torque.

Preload the pinon bearings by replacing the spacer between the pinon bearings with one smaller to the extent of the amount of the end play plus .002t! for the loading, For example, should there be .005" end playas indicated in the sketch in the assembly, replace the spacer with one .001" smaller. Do not depend upon the spacers to be right according to number but check each and everyone with an accurate micrometer. Before reassembling the bear ings to the pinion shaft they should be dipped in rear axle lubricant. Propeller shaft flange nut must be pulled down securely to assure tight bearings. A wrench with 30 11 of leverage should be used, In order to determine if insufficient or excessive preload has been applied, make the following te st:
A-22727
(1) Place assembly in vise with jaws clamp ing together on the flange of the pinion bearing cage and with assembly in a hori zontal position. (2) Grasp the propeller shaft flange with one hand and attempt to turn. (3) If the pinion turns freely, assembly is too loose. If pinion cannot be turned', assem bly is too tight, (4) The ideal condition is to secure a firm drag when turning the pinion cage by hand.
Fig. 17 - Using the pinion staking tool.

Pinion Bearing (Straddle bearing)
The straddle pinion bearing is held in place on the pinion by a staking operation. The staking operation is accomplished through the use of a hydraulic or screw press applying 18 to 20 tons pressure on the special staking tool as illustrated in Fig, 17, The re sult will be uniformly spaced ball indentations that securely lock the pinion bearing to the shaft.
After proper bearing fit has been obtained, place pinion bearing cage shims approximately .020 in thickness over end of cage and place cage and p,inion assembly in carrier, it being necessary to match flange holes in cage, since one hole is out of equal spacing to assure prop er position of cage. Next assemble two cage bolts only until gear setting is completed. Assemble differential and bevel gear assem bly and place bearing cap and adjuster in posi tion, Tighten bearing cap bolts and back off slightly to provide sufficient Iposeness to allow turning the adjuster for a temporary backlash adjustment of approximately .01 Ot!, After this adjustment has been made, tighten each bearing adjuster snug then give them a final tightening operation, drawing them up to secure the .005" to .007" total bearing'pre-load. This is im portant in order to make certain that the bear ings are seating properly. IMPOR TANT: Hypoid drive pmlon oil seals must be soft and pliable before being in stalled if the seals have become dried out and hard while in stock, use kerosene and work it in thoroughly. When seal has become soft and pliable, dip it in hot oil and work this oil in thoroughly.
PR!NTED IN UNITED STATES
Differential Ring Gear Rivet Removal

If necessary to remove hypoid ring gear or herringbone gear rivets, drill the rivet heads from the gear side, using a drill slightly larger than the rivet itself. Use a punch for the re moval of the remaining portion of the rivet. (See Fig. 18).
Knocking off or "busting" rivets is a dan gerous practice both from the standpoint of personal safety and because such practice may cause distortion to the gear carriers or gears and will elongate the rivet holes.
Rivet Pressures
Proper installation of differential ring gear rivets demands that sufficient pressure be applied to the rivets to expand them and cause them to completely fill the holes in which they are installed. Riveting should be done with COLD rivets, Hot rivets will shrink when cool, leaving s space and inviting shearing upon the application of torque.
or
A ME J<:IICA
Difierential case
A-22831
A.loon
Fig. 19 - Using a heavy hammer, strike sharply on the center of the flange of the axle shaft. This wi II unseat and loosen the tapered dowels in each stud hole.
Fig. 18 - Drill rivet head and punch-out as shown.
rivet
Riveting Jig SE-1575 is available and is designed for use with hydraulic or ITlechanical press equipITlent. The following pressures are recoITlITlended for differential ring gear rivet installation: RIVET SIZE (INCH) 5/16 3/8 7/16 1/2 9/16 5/8 PRESSURE PER RIVET (TONS) 12 17 30 45 60 60 to to to to to to 15 20 35 50 70 70
Axle Shaft Removal (Timken Axles)

Axle shafts are attached to the wheel hubs by studs and nuts at the flanged ene.. Stud holes in each axle shaft flange are taper-reaITled to receive split tapered dowels. When disasseITlbling the axle, SOITle of the bearing cage studs or axle shaft studs ITlay turn loose froITl the housing rather than at the nuts. When the axle is reasseITlbled, the nuts should be reITloved froITl the studs and the studs re placed in their tapped holes before installing the cage or carrier. When reITloving the axle shafts froITl the Tirnken axle, reITlove the stud nuts and lock washers and proceed as indicated in Figs. 19, 20, 21.
Fig. 20 - Remove the tapered dowels. Note: When reassembling there must be a sl ight clearance between the lockwasher and axle shaft driving flange. Excessive wear onstuds, dowels, or holes in the flange wi 11. indicate a lack of clearance at this point.
AXLE-REAR Section A 9
Cap Spring Location of breather valve on heavy duty axles
Valve body Rear axle breather valve
Fig. 21 - Push the axle shaft flange back into position against the wheel hub, and again, strike a sharp blow in the center of the axle shaft flange. This will cause thi axle shaft to spring away from the wheel hub and allow re moval of the axle shaft without resorting to the use of a pry bar or screwdriver. Do not pry between the axle shaft flange and wheel hub. To do so is apt to damage the seal as sembly or machined surfaces of the wheel hub or axle shaft flange.
When reinstalling the axle shafts the re must be a slight clearance between the lockwashers and driving , see Fig. 20. Excessive wear on studs, dowels or hole s in the axle flange will take place when no clearance exists.
Fig. 22 - Keep breather valves clean and free of obstruction. Breathers are usually located in housing as illustrated.
IMPORTANT Lubrication Of Hypoid Axles

The lubricant used in hypoid axles is an important factor in obtaining long gear life and satisfactory drive unit service. Past experi ence proves that a large portion of service problems can be traced to using incorrect, or lubricant of poor quality. In the selection of Hypoid Lubricants, it is advisable to consider using products of unques tionable quality. Because of the higher unit pressures and sliding tooth characteristics of h'ypoid gearing, the lubricant must have properties which en able it to withstand these actions.
It is important that the axle hypoid gearing receive initial lubrication after overhaul, or when a vehicle has been standing in storage, and BEFORE THE AXLE IS SUBJECTED TO HEAVY LOADS; Good practice is to check the lubricant level in the axle housing then, JACK UP BOTH rear wheels and operate the vehicle in high transmission gear at approximately 25 miles per hour for five minutes. This' will assure thorough lubrication of the gearing be fore the unit is placed into service. (Do not allow one wheel to race faster than the opposite wheel.)
Axle Housing Breather Valve

When the rear axle becomes warm, after a short period of operation, a pressure is built inside the axle housing. To prevent this pre's sure from forcing lubricant past the rear wheel oil seals and damaging the brake linings, a breather valve has been provided. The valve is so constructed that warm air may pass out of the axle to relieve built up pressure, yet dirt and moisture are prevented from entering. The location of the breather valve is shown in Fig. 18, inset shows detail of valve. The breather valve should be kept open and clean. When the vehicle is operated or un improved highways or in ice and snow it is possible that dirt will be forced under the valve cap, thus rendering the valve ineffective. Re move valve occasionally and clean thoroughly in a cleaning solution. NOTE: Where power divider is mounted on rear axle, the breather is mounted on upper side of the power divider.
PRINTEO IN UNITEO STATES OF AMERICA
Where the axle pinion cage is provided with a plug at the pinion cage, insert one pint of lubricant to provide initial lubrication for the pinion bearing.
. AXLE-REAR Section A Page 10

2. Using punch, drive the cross pin out of differential case far enough to remove the thrust blocks (Fig. 24).
Specified :Lubricant For Hypoid Axles

For hypoid axles (not Eaton) use SeL, EP gear oil or a multi-purpose gear lubricant suit able for hypoid axles and supplied by a reputa blerefinery. SAE-90for cold climate and SAE 140 for warm climate. For Eaton hypoid axle, use a hypoid gear lubricant available as Elco Gear Safety 1\281\ or its equivalent. A number of hypoid lubricantes are prepared by reputable companies which contain Elco additive concen trates. (See "Lubrication lf , section A). NOTE: When reassembling the differential gears, thrust washers, cross shaft spur gears and bearings, lubricate the wearing surfaces with a light coat of the specified axle lubricant.
Retainer
Differential Assembly -- L-110 and L-120

The L-110 and L-120 Series Trucks use differential assemblies that are identical in construction except that a spacer or thrust block is used when the unit is installed in a L-110 axle. Since the L-110 axle is of semi-floating construction, a means of taking up "the end thrust of the axles and wheels must be pro vided. The block serves this purpose. The wheel bearings pick up the end play or thrust on the L-120 (full-floating) axles and no thrust block is needed. Also the axle shafts in the full-floating design are slightly longer than those used in the semi-floating design and for this reason the thrust block must be removed when the differential unit is used in the L-120 series vehicle. Removal of the thrust block is as follows: 1. Drive cross pin retainer pin from differ ential case so as to clear the cross pin (Fig. 23).
Fig. 2'"
3. Push cross pin back into position in the differential case: Drive retainer pin into position and stake case to secure retainer pins (Fig. 25).
Stake the case to secure retainer pin
Fig. 25
A2J436
Fig, 23 - Driving retainer pin from differen tial case using a hammer and punch.
LLJNE MOTOR TRUCK SERVICE MANUAL
SINGLE-REDUCTION HYPOID AXLE

(UNIT SHOWN IS MODEL R-1060 OR R-1070)
A22643
Fig. 26 - Sectional
View of Hypoid Rear Axle.
1. Companion flange.
2. Propeller shaft mounting nut.
3. Propeller shaft mounting nut washer.
4. Pinion shaft bearing oil seal.
5. Pinion bearing cage to carrier capscrew.
6. Pinion bearing cage.
7. Pinion bearing, outer.
8. Pinion bearing
9. Pinion bearing,
10. Hypoid pinion gear (straddle mounting).
11. Pinion bearing.
12. Dife rential side gear.
13. Axle housing.
14. Differential bearing adjuster lock.
IS. 16. 17. 18. 19. 20. 21. 22.
23~
24. 25. 26. 27. 28.
Differential cross pin. Hypoid ring gear. Hypoid ring gear rivet. Diffe rential pinion. Axle shaft. Differential bearing adjuster. Differential carrier to housing gasket. Differential carrier to housing capscrew. Differential ro.ller bearing. Differential center block. Differential cross pin retaining pin. Differential case. Differential carrier housing. Pinion bearing cage shim.
NOTE: Rear Axle R-l070 is identical with above description except differential center block (24) is not used.
PRINTEO IN UNITEO STATES 0"" ,6.MERICA
AXLE-REAR Section A 12
SINGLE-REDUCTION HYPOID AXLE

(MODELS R-1165, R-1170, R-1440, R-1470, R-1530, R-1555, R-1630)
30
29
--.::----6
7
8
9
28 27 26
25
24 23
22
21---.l:::......:!
Fig, 27 - Sectional View of Hypoid Rear Axle

1. 2. 3. 4. 5. Axle housing. Hypoid ring gear. Differential bearing cap. Differential bearing cap mounting stud. Differential bearing. Differential bearing adjuster. Oil pasc:age to pinion bearings. Pinion bearing cage shims. Pinion bearing cage. Pinion oil seal retainer. Pinion oil seal. Slinger. Companion flange. Thrust washer. Propeller shaft companion flange nut. Pinion cage mounting capscrew. Differential carrier mounting capscrew. Pinion bearing cage cork seal. Thrust washers. 20. 21. 22. 23. 24. 25. 26. 27. 28. 29. 30. 31. 32. 33. 34. 35. 36. 37. Pinion bearing, outer. Pinion bearing spacer. Pinion bearing, inner. Hypoid pinion (straddle mounting). Pinion bearing. Differential case bolt lockwire. Differential case bolt. Differential carrier. Differential carrier mounting gasket. Axle shaft. Diffe rential bearing adjuste r lock. Differential side gear thrust washe r. Differential case, plain half. Differential side gear. Differential spider pinion. Differential spider pinion thrust washer. Differential spider. Differential case, flanged half.
6.
7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19.
AXLE-REAR Section B Page 1
TWO-SPEED AXLES
SEE SECTION "Hit FOR ELECTRIC SHIFT
A.2UI4
Fi g. I - Two-Speed Axle (Eaton)

1. 2. 3, 4. 5. 6. 7.
Hypoid ring gear. Oil collector drum. Ring gear case. Thrust washer. Bearing cap stud. Bearing cap. Carrier bearing. Clutch plate. Sliding clutch Shift fork. Shift fork shaft. Clutch plate. Sliding clutch. Diaphragm seal. Gear case bolt. Shifter motor stud.
8. 9,
lO.
11. 12. 13. 14. 15. 16.
17. 18. 19. 20, 21, 22. 23. 24, 25. 26. 27. 28. 29. 30. 31. 32.
Bearing, inner. Hypoid pinion. Bearing spacer, Bearing. outer. Companion flange. Washer. Nut Cage capscrew. Slinger. Seal. Washer. Pinion cage. Shims. Carrier, Carrier capscrew. Gasket.
33. 34. 35. 36. 37. 38. 39. 40. 41. 42. 43. 44. 45. 46. 47.
Axle shaft. Bearing adjuster lock. Bearing adjuster. Bearing cap, Thrust washer. Side gear thrust washer. Side gear. Differential pinion. Pinion thrust washer. Differential case. Pinion gear spider. Ring gear case. Idler pinion pin. Idler pinion gear. Axle housing,

correct positioning of gear on reassembly. (When reassembling hold adjuster and bearing cap up away from threads in bore of carrier unit; cap bolts are started. Drop cap; the threads of the adjuster and those in carrier will mesh freely.) 8, After removing bearing caps, tip up left hand end of planetary unit and lift out. 9. Remove pinion bearing cage capscrews. 10. Using a suitable puller, remove pinion assembly from carrier. May also be re moved by using a brass drift and tapping lightly from the inside. (Note shims under pinion bearing cage.) I L Remove pinion shaft nut and slide off com panion flange. 12. Lift off pinion bearing washer and spacer. cage, bearing,
EATON TWO-SPEED REAR AXLE

The two-speed rear axles are full-floating hypoid drive type, having four planetary gears which mesh with an internal gear on the hypoid ring gear. The primary reduction is accomplished through the hypoid ring gear and a straddle mounted hypoid pinion. The secondary reduc tion is accomplished with a sliding clutch serving to lock or unlock the planetary gears.
Serving
The correct servlcmg of this unit, as is true with any mechanical equipment, .is impor tant to satisfactory operation and life. Servic ing the two-speed unit does not require special tools. The ordinary equipment found in most shops is sufficient for this work. Use the fol lowing step-by-step procedure for disassem bling. Direct reversal of the action will be the proper reassembly procedure. (See Shop Talk No. 1 for step-by-step illustrations on disas sembly.)
Disassembly
Remove differential carrier assembly complete from the truck, following the same procedure as you would to take out a single or double reduction unit, except in this case, the two wires on the shift unit must be discon nected. For convenience in handling, the head maybe placed in the end of a clean small drum. The opening should be large enough to accept the bevel drive gear and bearing caps. Then proceed as follows: 1. Remove the two shift housing to carrier stud nuts and lockwashers and pull off shift unit assembly. (See section IIH" for electric shift instructions.) 2. Remove plug, washer, spring, capscrew, lockwasher and oil distributor. 3. Pull out shift fo rk shaft aite r removing shift fork shaft retainer (Fig. 2). The shift fork may then be slipped from the sliding clutch gear and removed through the back of the differential carrier. 4. Slip out sliding ~lutch gear. 5. Mark right hand differential bearing ad juster with punch. (This is for relocating when reassembling.) 6. Remove bearing cap bolt lockwires on both right and left hand sides. Loosen cap bolts only. Take off right hand bearing adjuster, lock and cotter pin. 7. Remove left hand differential bearing cap adjuster and lock as an assembly to assure
13. Drive off pinion bearing cage by tapping lightly between teeth of pinion alternately on opposite sides of inner race. CA UTION: Exercise care so as not to damage bearing during this operation. 12. Remove pinion bearing cone and washer cage assembly. Take out pinion bearing cage cork. (Replace this cork with every repair.) 15. Remove lockwires, nuts and bolts from planetary unit (support case). 16. Tap alternately on opposite sides of ring gear with head of rawhide hammer until gear is free of Hange on support cas e. (When reassembling, use two bolts to as sure proper alignment of bolt holes.) 17. Lift off left hand support case and bevel drive gear. lH. Pry off high speed clutch plate and take out idler pinions and pins. 19. Lift out entire differential asseITlbly and remove support case thrust washer. 20. Take out differential case bolt lockwire and remove bolts. (Note short bolts be tween spider arms.) 21. Lift off right hand differential case, Pick up long hub side gear, right hand, and slip off thrust washer. (Note-chamfered side of washer agains t back face of gear.) 22. Pull out spider and di[feren tial s ide pin ions noting thrus t washers behind pinions. Slip washers and pinions off spider arms. Take out short hub side gear, left hand

and remove thrust washer. (Note cham fered side of washer against back face of gear .) 23. Remove differential bearing cones by striking inner race on alternate sides through holes provided in the support case. 24. In reassembling the pinion, use SE-I065 pinion setting gauge in adjusting matched sets of pinions and ring gears to proper cone settings. (Theoretical cone centers for various axles are found under Specifi cations, Rear Axle Section.)
Gear Tooth Contact

To secure best possible tooth contact, use SE-I065 pinion setting gauge and follow in structions under this heading, Section ''A", page 2. Check results obtained by making a paint impression test of tooth contact. See Gear Adjustment for correct tooth contact - Paint Impression Method, Section "A", page 3.
Lubrication
An oiling system is provided to supply lu bricant within a half a turn of the truck wheels to the essential places during conditions when splash and dip alone would be insufficient. A heavy coating of oil is picked up by the oil collector drum and transmitted to the oil scoop. The oil scoop scrapes the oil from the drum and splits it into two courses, One half of this lubricant goes to the pinion bearings; the other half, to the right hand differential and planetary unit to the left differential bearing and then returning to the reservoir. Whenever a two-speed differential (new or rebuilt) has been installed in the axle housing, fill the oil reservoir to bottom of filler plug opening and replace plug. Then add one addi tional pint of lubricant using filler hole provided at top of carrier housing just above pinion cage. Use a hypoid gear lubricant available as ElcoGear Safety 1t28 lt or its equivalent: Anum ber of hypoid lubricants are prepared by repu table companies which contain Elco additive concentrates. Viscosity of the hypoidlubricant should be SAE-90. When high atmospheric tem peratures (above 100 0 F.) prevail, SAE-140 may be used. See "Lubrication" section A.
REASSEMBLY -- IMPORTANT Assembling Differential Unit

Lubricate both sides of all thrust washers well. Chamfered sides of washers must be against back face of side gears. Lubricate spider arms, side-pinion bores and side-gear hubs. Draw bolts tight with long-handled wrench and securely fasten with lockwire.
Assembling Planetary Unit

Before placing thrust washer, lubricate both sides well. Cover idler-pinion pins with lubricant. Chamfered teeth on high-speed clutch plate must face pinions. Place notches in oil-collector drum between bolt holes in bevel gear. Draw bolts tight with long-handled wrench and secure wire.
Pinion Shaft Bearing Adjustment

Desired bearing tension is obtained by us ing a spacer of the correct thickness between the bearing inner races. There are 12 spacers, each of different thickness, available for this purpose. To make the assembly, proceed as follows: 1. Place the pinion and bearings in position in the cage using original spacer, provid ing the pinion did not have any perceptible end movement before disassembly. 2. Then assemble flange washer and flange. Tighten retaining nut securely. There should be no perceptible end play and bear ing should roll freely. If correction is to be made select proper size spacer to ob tain de'sired fit.
Assembling Differential Carrier Unit

Lubricate all bearings as they are assem bled in carrier. After adjusting gear, be sure cap bolts are tight. Wire bolts securely, in cluding capscrews, in adjuster lock.
Pinion Bearing Pre-Load

Follow instructions given in Hypoid Rear Axle Section HAll, page 6.
Differential Carrier Bearing Pre-Load

The correct procedure for securing the specified carrier bearing pre-load, as listed in the Rea,r Axle Specification for these axles, will be found in Section "All, Hypoid Rear Axles.
PRINTED IN UNITED STATES
Fig. 2
or
AMERIG"
AXLE-REAR
Section C Page 1
DOUBLE-REDUCTION AXLE
(EATON)
~4i------::
'13
14 15 16
17
18
19, , 20
,A.22813
Fig. I Double-Reduction Axle (Eaton)

1. 2. 3. 4. 5. 6. 7. 8. 9. 10. Carrier gasket. Carrier. Herringbone gear. Gear rivet. Oil distributor disc. Case, flanged half. Case bolt and nut. Thrust washe r. Bearing cap. Cap stud. Lock ring. Bearing. Side gear. Thrust washer. Lock ring. Oil scoop.
PRINTED IN UN!TEO STATES
11.
12.
13.
14. 15. 16.
17. 18. 19. 20. 21. 22. 23. 24. 25. 26. 27. 28. 29. 30. 3l. 32.
orAMRICA
Spring and plug. Axle shaft. Counte r shaft bearing. Pinion countersh3it. Cage capscrew. Bearing cage. Carrier capscrew. Cage shiITls. Oil reservoir. Hypoid pinion. Bearing, inner. Bearing spacer. Bearing, outer. Washer. Slinger. Companion flange.
33. 34. 35. 36. 37. 38. 39. 40. 4l. 42. 43. 44. 45. 46. 47. 48.
Cotter pin. Nut. Washer. Oil seal. Bearing cage. Cage shims. Oil passage. Hypoid ring gear. Oil distributor disc. Oil scoop. Oil scoop capscrew. Spider pinion. Pinion thrust washer. Case, plain half. Spider. Axle housing.
AXLE-REAR Section C Page 2

IMPORTANT: Hypoid drive pinion oil seals must be soft and pliable before being in stalled if the se;;Lls have become dried out and hard while in stock, use kerosene and work it in thoroughly. When seal has become soft and pliable, dip it in hot oil and work this oil in thoroughly.
EATON DOUBLE-REDUCTION REAR AXLE

The Eaton double-reduction rear axles, shown in Fig. 1, are heavy-duty. double reduc tion type. The primary reduction is through a hypoid ring and pinion gear while the secondary reduction is through a set of herringbone gears.
Primary Reduction
The primary reduction gears are the hy poid type, consisting of a hypoid pinion mounted on the forward end of the carrier housing, and meshed with a hypoid ring gear which is riveted to an integral flange on the ring geariii shaft. This shaft also carries, as an integral part, the herringbone drive pinion for the secondary reduction.
Pinion Bearing Lubrication

NOTE: When reassembling differential to axle housing, or new and dry differential is used from stock, be sure to inject about one pint of differential lubricant into the pinion bearing housing through the filler plug opening at the side of the carrier. This will provide immediate lubrication for the pinion bearings upon placing the unit in operation.
Secondary Reduction
The secondary herringbone reduction gears consist of a drive pinion and a mating gear. The teeth on the secondary reduction gears are right and left-hand spiral cut in line with each other, forming a "VI!, the apex of which is at the center of the gear face. A center cut through the apex breaks the tooth line into two separate and opposed spiral gears, each exert ing equal and opposed pressure thus balancing thE:; end thrust.
Herringbone Gear Shaft (Cross Shaft)

The herringbone drive pinion gear shaft is mounted at right angles to the hypoid pinion shaft in the carrier housing. This shaft is a one-piece steelorging consisting of an integral herringbone gear in the center and an integral flange on one end to which is bolted a hypoid ring gear. To remove this shaft, it is necessary to remove the differential and herringbone ring gear assembly. Then withdraw the hypoid pin ion and cage assembly far enough to clear the hypoid ring gear, when being removed. (Re moval of universal joint flange is unnecessary.) Remove both bearing covers and using a soft hammer, tap ring gear end of shaft until the bearing cup at opposite end of shaft is removed from carrier housing. This will permit suffi cient opening to partly pass shaft through until bearing is clear of carrier housing at ring gear end of shaft. Tilt ring gear end of shaft to rear and withdraw from carrier. The cros s shaft bearing covers control the hypoid pinion and ring gear backlash and tooth contact as well as the bearing pre-load. This is accomplished by means of a shim pack under each bearing cover.
Installing New Herringbone Drive Gear

(Differential Case)
If new gears are being ins taIled, the pilot diameter on differential case drive gear flange should be checked to see that it runs true. If inspections indicate a run out of .004", a new differential case should be installed. When assembling drive gear on face of flange, make sure each rivet is tight. The best results are obtained if a press is used to install rivets. Follow the instructions outlined under Rivet Pressures on page 8, Section "At!.
Hypoid Pinion Shaft and Adjustment

Adjustable hypoid pinion bearings are assembled to pInIOn shaft and retained by universal joint flange and nut on forward end of pinion shaft. A spacer (available in several thicknesses) is used to maintain correct distance between front and rear bearings and to secure the pin ion bearings pre-load as indicated in Rear Axle Specifications. The pinion cage is mounted in the conventional manner and the correct. cone center adjustrnen.t is secured by means of a shim pack under pinion cage flange. See SE-l065 Pinion Setting Gauge, Section "A", page 2).
Herringbone Gear Adjustment

Herringbone gears are not adjustable for backlash. This clearance is taken into account in the construction and remains constant as long as the gears remain undamaged or the differ ential carrier bearings are not worn excessive ly. The self-aligning differential carrier bear ings eliminate the need for adjustment to align the herringbone pinion and herringbone ring gear. The heavy duty roller bearings permit

the differential carrier to move sidewise within the bearing race sufficiently to keep both gears in perfect alignment at all times.
AXLE-REAR Section C Page 3
Lubrication of Hypoid Axles

The lubricant used in hypoid axles is an important factor in obtaining long gear life and satisfactory drive unit service. Past experi ence proves that a large portion of service problems can be traced to using incorrect, or lubricant of poor quality. In the selection of Hypoid Lubricants, it is advisable to consider using products of "unques tionable quality.
Differential
Differential is convential four-pinion type with thrust washers back of side gears and pin ions. Cases are supported on heavy duty roller bearings.
Differential Lubricators
The double reduction axles have special provision incorporated to supply oil to the her ringbone pinion shaft bearings as well as the hypoid pinion shaft bearings. This is accom plished by scooping lubricant from oil collector discs mounted on the herringbone gear and the hypoid ring gear. The lubricant is picked up from these discs by oil scoops and circulated through special passages to the differential car rier bearings and the herringbone pinion shaft bearings. Fig. 2 illustrate s the flow of oil and the principal of this means of bearing lubrica tion. Because of the higher unit pressures and sliding tooth characteristics of hypoid gearing, the lubricant must have properties which en able it to withstand these actions.
It is important that the axle hypoid gearing receive initial lubrication after overhaul, or when a vehicle has been standing in storage, and BEFORE THE AXLE IS SUBJECTED TO HEAVY LOADS. Good practice is to check the lubricant level in the a.xle housing then, jack UP BOTH rear wheels and operate the vehicle in high transmission gear at approximately 25 miles per hour for five minutes. This will as sure thorough lubrication of the gearing before the unit is placed into service. (Do not allow one wheel to race faster than the opposite wheel.)
Where the axle plmon cage is provided with a plug at the pinion cage, insert one pint of lubricant to provide initial lubrication for the pinion bearings. NOTE: When reassembling the differential gears, thrust washers, cross shaft spur gears and bearings, lubricate the wearing surfaces with a light coat of the specified axle lubricant. This will help provide initial lubrication. Use a hypoid gear lubricant available as ElcoGear Safety filS!! or its equivalent. A num ber of hypoid lubricants are prepared by repu table companies which contain Elco additive concentrates. Viscosity of the hypoid lubricant should be SAE - 90. When high "atmospheric tem peratures {above 100 F.) prevail, SAE-I40 may be used.
Fig. 2
PRINT!'::O IN UN'ITO STATS 01' AME:RICA
AXLE-REAR Section D Page 1
SINGLE-REDUCTION AXLE
(TIMKEN 100 SERIES AXLES)
Fig. I - Single-Reduction Timken 100 Series Axle

1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. Pinion shaft nut. Pinion shaft nut washer. Companion flange or yoke. Oil seal. Thrust washer. Pinion bearing, outer. Pinion bearing spacers. Cover gasket. Bearing cover. Pinion bearing cage shims. Pinion bearing, inner. Pinion. Lubricant filler plug. Pinion radial bearing. Breather. Differential side bearing. Adjusting nut (differential). Axle shaft.
PAINTEO IN UNITEO STATES OF AMEFfle,,"
19. 20. 21. 22. 23. 24. 25. 26. 27. 28. 29. 30. 31. 32. 33. 34. 35. 36. 37.
Adjusting nut lock. Differential bearing cap. Side gear thrust washer. Side gear. Pinion thrust washer. Pinion bushing. Differential spider. Pinion gear. Bevel drive gear. Rivet. Differential pan bolt, long. Differential case. Differential case bolt, short. Thrust block adjusting screw. Lock nut. Thrust block. Differential carrier. Pinion bearing cage. Slinger.
TIMKEN SINGLE-REDUCTION AXLES Description

The Timken Single-Reduction Rear Axle (R-IOO) is a full-floating, hypoid-type final drive, assembled in a one-piece axle housing. The differential used in the R-lOO Timken Single-Reduction Axle is of four-pinion-type with thrust washers used between the pinions and case. The pinions contain bushings which can be renewed when necessary. Thrust wash ers are also used between the side gears and case. The two halves of the differential case are machined as a complete assembly and must be replaced as such.
Removal of Differential Carrier - Hypoid

To remove the differential carrier assem bly, remove plug from bottom of axle housing and drain out the lubricant. Disconnect the propeller shaft atfront end of pinion shaft. {Be sure to replace the universal joint trunnions on their respective journals and hold them in place with a short loop of wire until ready to reassemble.} Remove axle shafts and differ ential carrier to housing capscrews {or stud nuts on heavy-duty axles}, and take out carrier. When removing the differential from the axle housing, it will be necessary to utilize the two puller screws to loosen the differential carrier as shown in Fig. 2. The differential thrust block screw shown in Figs. 3 &: 4 must be removed before the dif ferential can be removed from the carrier.
Fig. 2 - Loosen lock nuts on two puller screws provided, and turn pul Jer screws down into car rier. It may be necessary to break carrier loose from housing by striking the carrier with a heavy soft hammer (lead or leather).
Differential
The differential assembly of this axle con sists of four nine-tooth pinions mounted on a spider and two 16 tooth side gears all assem bled into the differential case -- One half being flanged to mount the hypoid ring gea r. Hardened steel thrust washers are installed between the side and the case and between the pinions and case. The differential case is held together by twelve bolts. eight of which are longe r than the remaining four.
Fig. 3 - Place differential carrier in suitable holding fixture or overhaul stand, and loosen the lock nut on the drive gear thrust block ad justing screw. Remove thrust block adjusting screw from carrier. This wil I permit the thrust block to fall into the carrier.
,Rotate gear to Ibring hole.in block. 'iIi line with adjusting
Differential Disassembly
Mark each half of the differential case before teardown so tnat they can be reassem bled in the original position. Wash and inspect all parts and replace any which are at all questionable. Oil all parts with gear oil before reassembly. Use new lockwashers when re assembling.
Fig. ~ - When replacing thrust block, place block on gear and rotate gear to bring block in line with adjusting screw.
Press
Preas burnishiDg ball .. thro~b bushiDg
Fig. 5 - If it is necessary to remove the ring gear from the differential case half, carefully center punch each rivet in the center of the rivet-formed head as shown. Dril~ through the center of each rivet-formed head, using a dril I sl ightly larger than the body of the rivet. Punch or press rivet out of gear and case half.
Fig. 6 - Use bar to press burnishing ball through bushing. The correct size bal I should be approximately .005" larger than the differ ential spider trunnion.
If inspection reveals that the ring gear should be replaced, exercise care when remov ing the ring gear rivets. Fig. 5 shows the correct way to remove the ring gear rivets to avoid damage to the differential case.
Remove the pinion shaft from the pinion cage on a press. Remove the inner pmlOn bearing with a suitable puller. The inner radial bearing retainer is removed after removal of the retainer screw.
The four differential spider pmlOn gears run on bronze bushings and where they are found to be worn excessively, the bushings can be replaced. Cut the old bushings out of the pinions and using the special tool shown in Fig. 6, install and burnish the new bushings in the pinions. Bronze bushings are burnished by means of a stud ball which, when being pressed through the pinion bushings, compresses the bushing metal, giving a denser surface and tighter fit in the pinion. The burnishing operation also locks the bushings in place in the pinion, since some of the bushing metal is compressed into the locking groove located on the inside bore of the pinion. The correct size ball should be ap .. proximately .005 11 larger than the spider trun nion. Do not attempt to ream the spider pinion bushings.
Pinion Bearing Pre-Load

When the pinion shaft, bearings, bearing spacers and pinion cage have been reassembled,
Pinion
The pmlOn cage can easily be withdrawn, from the differential carrier with the use of puller screws provided.
PRINTED IN UN1TO STATES OF' AMERICA
Fig. 7 - Checking pinion bearing pre-load using torque method.

When installing new gears, check gear lash with dial indicator (Fig. 8) and adjust to obtain .006 11 to .01211 lash as follows: 1. To :move pinion toward gear, re:move shi:ms fro:m pack under pinion cage. 2. To :move pinion away fro:m gear, add shi:ms under pinion cage. 3. To:move gear,tightenor loosendiHerential bearing adjusting nuts as required. After correct gear lash is secured, check and adjust as necessary to obtain the correct tooth contact. (See gear Adjust:mentfor correct tooth contact.)
be sure to check the bearing pre-load. Attach a scale to the end of a soft wire wrapped around the pinion cage as in Fig. 7. Read the scale only when pinion cage is :moving (rotating torque). If first adjust:ment does not result in correct pre-load, select a thicker co:mbina tion of spacers to decrease, or use thinner co:mbinations of spacers to increase the bearing pre-load. The rear axle specifications list the correct bearing pre-load for these axles.
Gear Adjustment for Correct Tooth Contact

Checking tooth contact is acco:mplished by :means of oiled red lead applied lightly to the bevel gear teeth. When the pinion is rotated, the red lead is squeezed away by the contact of the teeth, leaving bare areas the exact size, shape and location of the contacts.
Adjust Differential Bearing Pre-Load Gear Adjustment for Lash

Generally, if original gears are being re installed, red leading of teeth will not indicate the sa:me contact as new gears and can be :mis leading. Gears that have been in service for long periods for:m running contacts due to wear of teeth; therefore, the original shi:mpack should be maintained to check gear lash. Gear lash, when using original gears, can be reduced only to a point of s:mooth rotation of gears.
If the gear lash in in excess of :maxi:mu:m tolerance as stated under gear adjust:ment, the lash :may be reduced only in the a:mount that will avoid overlap of the worn tooth section. Rotate the gears and check for s:mooth or rough operation. If a slight overlap, takes place at the worn tooth section, rotation will be rough.
Using dial indicator at back face of ring gear (Fig. 9), adjust to obtain bearing pre-load as follows: 1. Loosen adjusting nut on side opposite gear teeth only enough to notice end play on in dicator. 2. Tighten sa:me adjusting nut only enough to obtain .000 11 end p'lay reading on indicator. NOTE: While gear is held in .000" end play and before loading bearings, check gear for runout. If runout exceeds .008 11 , re:move differential and check for cause.
Fig. 8 - Checking gear lash.
Fig. 9 - Adjusting load.
differential
bearing
pre

3. Tighten BOTH adjusting nuts one notch each from .000" and play to pre-loaddifferential bearings. 4. Tighten bearing cap stud nuts to specified torque (L-lOOand R-100 Axle). (RearAxle Specifications). 5. Install adjusting nut locks, capscrews and lock wires.
Lubrication
1. Remove inspection and oil filler plug (Fig. l) and fill to level of plug hole with spec ified lubricant. Capacity for the R-lOO axle is 30 pints (30lbs.). Capacity of the L-lOO axle is 23 pints (23 lbs.).
Thrust Block Installation

Turn carrier assembly to bring back face of ring gear facing upward and install the thrust block as follows: 1. Place thrust block on rear face of gear and rotate gear until hole in thrust block is aligned with the adjusting screw hole. NOTE: A light coating of grease placed On the thrust block face will serve to hold the block in position on the rear face of the gear.
2. Jack up BOTH rear wheels and operate vehicle in high transmission gear at ap proximately 25 miles per hour for five minutes to assure proper lubrication of all parts before the Unit is put into service. Both wheels should rotate at approximately the same speed while the vehicle is jacked up. Do not allow one wheel to race faster than the opposite wheel. To do so might cause serious damage to the differential spider and gears. Use SCL, EP gear oil or a multi-purpose gear lubricant suitable for hypoid axles and supplied by a reputable refinery. SAE-90 for cold climate and SAE-140 for warm climate.
Fig. 10 - Adjusting clearance of thrust block. Turn adjusting screw out of carrier I/q turn to obtain .010 to .015 inch clearance.
2. Install adjusting screw and lock nut. Tight en adjusting screw to force thrust block against gear, then back off one quarter (1/4) turn and lock securely with lock nut (Fig. 10). Clearance between back face of gear and thrust block is .010 to .015". CAU TION: Be sure that the adjusting screw end is seated properly in the thrust block hole.
AXLE-REAR Section E Page 1
DOUBLE-REDUCTION TWO- SPEED AXLE

(TIMKEN 300 SERIES AXLES)
FAST SPEED HELICAL GEAR SLOW SPEED HELICAL GEAR
FAST SPEED
FREE ROLLiNG\VHEN COLLAR
ENGAGES SLOW SPEED PINION
SPACER-SELECTION OF
PROPER SPACER GIVES
DESIRED PINION BEARING
PRE.LOAD
SLOW SPEED PINION
CROSS. SHAFT ASSEMBLY
SHIFT COLLAR SLIDES ON ,SPLINED PORTION OF SHAFT ENGAGING DESIRED PINION
AI.579C/
Fig. I - Two-speed Double-Reduction Drive Unit
Description
The Timken Two-Speed Double-Reduction Final Drive Differential (Fig. 7) provides two gear ratios--actually two full size final drives in one unit; a "fast" ratio for maximum speed and a "slow" ratio for maximum pulling power. This feature enables the truck driver to use the proper axle gear combination required for speed, load and road conditions.
gears attached to the tapered roller bearing mounted diffe rential. On the inner side of each of the spur pinions are integral splines. On the cross shaft are two rows of splined teeth. A shift fork, actuated by an electric power shift unit, ITIoves the shift collar on the splined portion of the cross shaft to engage the splines on the fast or slow speed spur pinion. See Fig. 4. When the fast axle speed is selected and torque released, the shift collar is moved to ward the fast speed spur pinion, and atthe same time disengages the splines on the slow speed spur pinion. The fast speed spur pinion then revolves as part of the cross shaft to drive the fast speed spur gear. During this operation the slow speed spur pinion is disengaged so as to rotate freely on the cross shaft. Power is transmitted through the hypoid pinion and gear, cross shaft, clutch collar, fast speed spur pin ion and gear, differential and axle shafts. When the slow speed is selected and torque released the shift collar moves in the opposite direction disengaging the fast speed spur pin ion and locking the slow speed spur pinion as part of the cross shaft. Power is then trans mitted through the slow speed spur pinion and gear, differential and axle shafts.
Operation
The first reduction in the Timken Two Speed Double Reduction Drive Axle is through a heavy duty hypoid bevel pinion and gear. The hypoid bevel pinion and gear set operates in conjunction with either of two sets of wide-face helical spur gears and pinions of different ratios. This second reduction is selective between a fast or slow ratio. The bevel pinion is mounted on two tapered roller bearings in a pinion cage. The bevel gear is locked on the cross shaft by a key. The cross shaft is mounted on tapered roller bear ings and carrier two free-rolling helical spur pinions. Both spur pinions engage helical spur
PRINTED IN UNITED StATES OF' .MERICA

installation the gear may be heated to 200 to 250 0 F. Be sure the key is in line with the key slot in the gear before pressing the gear into place. The fast speed pinion located between the hypoid ring gear and splined teeth on the cross shaft should have an end play of at least .010 11 Normal end play will be from .015" minimum to ,030 11 maximum. The slow speed pinion end play must also check to a minimum of .010". The shift collar is installed over the springs and poppets with the longer splines on the in side diameter of the collar toward the hypoid ring gear. The cross shaft bearing pre-load is meas ured by wrapping wire around the slow speed pinion and pulling with a scale to a reading of approximately 8 pounds rotating torque (not starting torque), (Fig. 3). To obtain correct pre-load add or remove shims at shim pack under bearing cage on cross shaft end opposite ring gear. Use origi nal shim packs plus a new gasket when rein stalling original gears.
The design of the shift collar prevents dis engagement until the opposite gear ratio is selected and torque released.
Adjustments and Clearances

Various clearance adjustments are pro vided for both in the axle gearing and shifting mechanism. These adjustments once made, seldom need attention. Where a disassembly job is to be performed, the detailed information found in Shop Talk No. 34 will be most helpful.
Hypoid Pinion and Cage

The pinion and bearings are installed in the pinion cage witha pre-load secured by following the instructions under PinionBearing Pre-Load, Sec. A. The pre-load in controlled by proper selection of spacers, or combination of spacers, located between the outer pinion bearing and bearing seat on the pinion shaft (Fig. 1). These spacers are ground to close tolerances and are available in graduated thicknesses. Thicker spacers decrease bearing pre-load and thinner spacer bearing pre-load. For correct procedure see pinion bearing adjustment for correct pre-load, Sec. A. When installing the pinion cage assembly in the differential carrier, be sure that the oil passage holes in the carrier housing, gasket, shim pack and pinion bearing cage are aligned. When the original gears are being reinstalled use the original shim pack plus a new gasket under the pinion cage.
Hypoid Ring Gear and Cross Shaft

The hypoid ring gear is assembled on the cross shaft by pressing the gear firmly against the cross shaft shoulder (Fig, 2), To facilitate
Fig. 3 - Checking cross shaft pre-load

.010 MINf,,' . C[EARANC~\
'.7WHEN~""
.~~~I!Jjjfii~:'
Gear Tooth Impression and Lash
When the hypoid gear sethas been renewed, adjust gear back lash with dial indicator, and adjust to obtain .006" to .01211 lash. Movement of the gears is controlled as follows: 1. To move pinion toward ring gear, remove shims from pack unde r pinion cage. 2. To move pinion away from ring gear, add shims to pack under pinion cage. 3. To move ring gear away from pinion, re move shims from pack under cross shaft bearing cage (side opposite ring gear) and add shims of equal thickness to pack under
HypoilYGEAR
IS PRESSEDf
. A-GAINSf'
-fiK'SEAT:;
Fig. 2 - Pressing hypoid gear on cross shaft.

cross shaft bearing cage (ring gear side). Shims should be transposed in this manner to maintain the established pre-load. 4. To move ring gear toward pinion, remove shims from pack under cross shaft bearing cage (ring gear side) and add shims of equal thickness to pack under cross shaft bear ing cage (side opposite ring gear). Shims should be transposed in this manner to maintain the established bearing pre-load. When correct gear lash is obtained, check and adjust as necessary to obtain correct tooth contact using oiled red lead applied lightly to the ring gear teeth. Gear tooth impression illustrations are shown in Section "A," pages 3 and 4.
Check clearance of shift fork collar (flat) faces in shift collar with feeler gauge (Fig. 4). The clearance should not be less than .010" minimum on each side of the fork' in both the fast and slow speed positions. When checking this clearance the shift collar must be flush with the end face of the spur pinion in both fast and slow positions. Shims located at the shifting chamber bracket regulate the travel range of the shift rail and fork. Add or remove shims to allow the shift collar to seat flush against the spur pinions in both high and lowpositions (Fig. 5 & 6). The electric shift chamber and bracket assem bly must be removed from the carrier in order to remove shims.
Shift Collar Adjustment

The shifting collar serves as the lock be tween the cross shaft and either the high or the low speed spur pinions. When engaged with either speed spur pinion the collar must be flush against the spur pinion face (Fig. 4). The collar is held flush against the pinions by three spring loaded poppets located in the cross shaft, and unless there is misadjustment in the loca tion or travel of the shifting fork the collar will seat itself against whichever gear is selected.
Spring - completes shift
when engine torque
is released
A-22924
Fig. 5 - Details of front mounted electric shifting mechanism. Note location of shims for travel adjustment.
Electric shift motor
Spring-completes shift
when engine torque
is released
Fig. ~ -Checking clearance between shift collar and spur pinion. Clearance shoul~ not be less than .010".
To check the travel of the collar when the differential is mounted on the axle housing it is necessary to remove the pinion cage assembly. Illustrations show details of the checking pro cedure with the carrier removed from the axle housing and the differential gear assembly re moved.
Fig. 6 - Showing details of side mounted elect ric shift mechanism. Shims are provided to ad just travel of shift fork. Overhaul procedure for the electric shifting unit is given in the Electric Shift Section "HR,

Lubrication
1. Before starting new truck and after over haul, remove pipe plug at pinion cage and insert one pint of specified lubricant. 2. Fill axle housing to correct level with spec ified lubricant. Capacity is 18-1/2 quarts (37 1bs.). 3. Jack up BOTH rear wheels and operate vehicle in high transmission gear at ap proximately 25 miles per hour for five minutes to assure proper lubrication of all parts before the unit is put into service. Both wheels should rotate at approximately the same speed while the vehicle is jacked up. Do not allow one wheel to race faster than the opposite wheel. To do so might cause serious damage to the differential spider and gears. Use SCL, EP gear oil or a multi-purpose gear lubricant suitable for hypoid axles and supplied by a reputable refinery. SAE-90 for cold climate and SAE-l40 for warm climate. When reassembling the differential gears, thrust washers, cross shaft spur gears and bearings lubricate the wearing surfaces with a light coat of specified axle lubricant. This will help provide initial lu?rication.
Fig. 7 - Adjusting stop screws to limit travel of shifting fork. Fig. ~ shows point of contact of the screws with the shifting collar.
Adjusting screws located on top of the car rier housing (Fig. 7) provide means of limiting the travel of the shifting fork and rail. Turn in or out on each adjusting screw to stop the travel of the shifting fork so that the fork does not bear against the sides of the shifting collar after the collar is seated flush with the spur pinionface in both high and low positions. There must be a minimum of .01 on clearance between the fork and shift collar. This clearance is to assure that the collar is free of shifting fork interference and allows the poppets to hold the collar against either qf the spur pinions. Also the .01 on minimum clearance is running clear ance between the forks and collar sides to pre vent unnecessary wear to the two parts.
Differential Adjustment
The differential assembly is installed in the carrier with the helical gears located to provide approximately 1/16 11 clearance between the helical gear sides and shift collar faces in both the fast and slow speed positions. Move the differential assembly from side to side to obtain this adjustment by turning on the adjust ing nuts. Using dial indicator at the side face of one of the helical gears adjust to no end play (.OOO" end play), in the differential bearings. Rotate assembly several times to assure normal bear ing contact. Tighten adjusting nuts one notch each from .000" end play to secure the correct differential bearing pre-load. With the dial indicator contacting the side face of the helical gear check for runout. If runout exceeds .008" remove differential and, check for cause.
Fig. 8 - Insert one pint of lubricant in pinion cage before starting new truck or after over hau I.
Electric Shift
The electric shift mechanism used on all Tirnken double-reduction two speed axles is identical with the electric shift used on Eaton two speed axles. For detailed information see Electric Shift Section "H".
AXLE-REAR Section F Page 1
DOUBLE-REDUCTION AXLE
(TlMKEN 200 SERIES AXLES)
(See Shop Talk No. 25 for complete illustrated disassembly)
Hypoid gear
Hypoid pinion
Differential case
Helical gear
A-I0067
Fig, I - Double-Reduction Drive Unit (Timken).

The Timken S-200-P and U-200-P series double-reduction rear axles (Fig. 1) introduce improvemen ts in des ign and cons truction over conventional rear axles for on-highway and off highway service in heavy-duty motor trucks. These axles provide increased torque ca pacity and eliminate the former need, because of specific chassis requirements, for both top mounted and front-mounted double-reduction final drive units. The differential carrier on the S-200-P and U-200-P axles is mounted at an elevation which is a satisfactory compro mise between the two extremes. The S-200-P and U-200-P rear axles em ploy the same differential and carrier assem blies. They differ only in that the rear axle housing of the S-200-P is of lighter construc tion for the S-200-P axle is not intended for off-highway service. legs are dowelled in the axle housing to elim inate deflection under torque load.
Pinion Shaft Location

The pinion shaft is located at an elevation midway between that used on the front-mounted type axles, where the pinion shaft is on the axle center line, and that used on the top mounted type axles, where the pinion shaft is considerably above the axle center line (Fig. 1).
Final Drive
The final gear-drive consists of a large diameter hypoid bevel gear and bevel pinion for the first reduction, and a wide-faced helical gear and helical pinion for the second reduction. A range of gear ratios is available to meet all operating requirements. (See Specifi cations.)
Drive Unit
The drive unit, or differential carrier as sembly, is mounted on the sloping front face of the axle housing and is readily removable for periodic inspec tion. The differential bearing
PRINTED IN UNITED STATES OF "MERICA
Axle Housing
The axle housings in both axles are simi lar in design, although the U-200-P axle hous ing has larger sections to produce its greater load carrying capacity.
Differential
The differential assembly of this axle con sists of four 9-tooth pinions mounted on a spi der and two 16-tooth side gears all assembled into the differential case, both halves of which are identical. Hardened-steel thrust washers are in stalled between the" side gears and the case and between the pinions and the case. The large helical gear is mounted between the differential case halves and the assembly is held together by twelve rivets. The differential assembly is mounted in tapered roller bearings.
on Seals
The rear wheel outer oil seal is illus trated in Fig. 2. This is the latest type oil seal assembly and when installing this seal, be sure to cement the new cork gasket to the inner flange of the new wiper ring.
4.19.63.4
Fig. 3 - Illustrates wiper ring and gasket.
Fig.
1.1:
Axle shaft
Cork gasket cemented to seal wiper A.I60f4
Fig. 2 - Illustrates sectional installed.
view of seal
The seal wiper and cork gasket are pressed over the end of the axle tube. Be care ful not to bend or damage the seal wiper when installing. (Fig. 3). The seal retainer assembly is placed over the axle flange studs, as shown in Fig. 4, using a gasket on both sides of the seal retainer as sembly. The rear wheel inner seal construction is illustrated in Fig. 5. Before installing the inner seal, check the location of the bearing and oil seal spacer to be certain that the seal lip on the oil seal assembly faces toward the oil seal wiper ring in the wheel hub, as shown. Special adapters should be used in seal installation as described in Service Bulletin B-97-1946 and Addendum No. 1.
Fig. 5 - Rear wheel inner seal.

Lubrication
1. Before starting new truck and after over haul, remove pipe plug at pinion cage and insert one pint of specified lubricant. 2. Fill axle housing to correct level with specified lubricant. The various axle ca pacities are found in Lubrication Section. 3. Jack up BOTH rear wheel and operate ve hicle in high transmission gear at approxi mately 25 miles per hour for five minutes to assure proper lubrication of all parts before the unit is put into service. Both wheels shOUld rotate at approximately the same speed while the vehicle is jacked up. Do not allow one wheel to race faster than the opposite wheel. To do so might cause serious damage to the differential spider and gears. Use SeL, EP gear oil or a multi-purpose gear lubricant suitable for hypoid axles and supplied by a reputable refinery. SAE-90 for cold climate and SAE-l40 for warm climate.
To remove the cross shaft, it is necessary to fir st remove the differential and helical ring gear assembly:. second, withdraw the hypoid ring gear when being removed. (Do not remove universal joint flange.) Then remove both bearing cages, move shaft enough to allow bearing at ring gear end of shaft to clear the carrier housing and tilt shaft to rear for re moval from carrier. The correct bearing pre-load is obtained by adding or removing shims at shim pack under the cross shaft bearing cage at end op posite hypoid ring gear. Use orignial shim pack plus a new gasket when reinstalling ori ginal gears. To measure correct bearing pre load, follow method outlined for Timken Double Reduction Two-Speed Axles, Section E, Fig. 3.
Hypoid Pinion and Cage

The pinion and bearings are installed in the pinion cage with a pre-load as indicated in Rear Axle Specifications for these axles. The pre-load is controlled by proper selection of spacers, or combination of spacers, located between the outer pinion bearing and bearing seat on the pinion shaft. These spacers are ground to close tolerances and are available in graduated thicknesses. Thicker spacers de crease bearing pre-load and thinner spacers increase bearing pre-load. For correct pro cedure, see Pinion Bearing Adjustment for correct pre-load, Section "A", page 6. When installing the pinion cage assembly in the differential carrier, be sure that the oil passage holes in the carrier housing, gasket shim pack and pinion bearing cage are aligned. When the original gears are being reinstalled use the original shim pack plus a new gasket under the pinion cage.
Helical Gear Shaft (Cross Shaft)

The helical gear or cross shaft is mounted at right angle s to the hypoid pinion shaft in the carrier housing. This shaft is a one -piece steel forging consisting of an integral helical drive pinion gear in the center. The hypoid ring gear is aligned with key in shaft before pressing gear onto shaft.
PRINTEO IN UNITED STATES OF AMERICA
AXLE-REAR Section G Page 1
TANDEM AXLES
See Legend on following page
8-4745
Fig. I - Details of axle mounted power divider mounted on forward rear axle.
AXLES--RF-1475, RF-1575, RF-1685.
FOUR-WHEEL, AXLE-MOUNTED POWER
DIVIDER
The above axles have a power divider built as an integral part of the differential assembly. This results in a more simplified tandem axle design, with less moving parts. The compact ness of the combined power divider and differ ential makes possible the use of fewer propeller shafts and eliminates the need for a propeller shaft hanger at the rear of the vehicle. The
PRINTEO IN UNITEO !JT"'TS OF AMERiCA
power from the engine is delivered through the transmission (and auxiliary transmission where the truck is so equipped) to the power divider which, as the name implies, divides the power between the two axles. A differential unit is included in the power divider to com pensate for the difference in speeds between the two axles. This difference in axle speeds is brought about by wheels Slipping on either of the axles or slightly different tire diameter due to tire wear. (Both rear axles on six wheel (6x4) trucks have the same axle differ ential ratio.)

Legend For Fig. 1
1. Mainshait.
*2. Companion flange retaining nut.
3. Companion flange. washer.

5.: Slinger.
6. Felt. 7. Oil seal. B. Bearing cover retaining nut. 9. Bearing cover. 10. Bearing cover gasket. 11. Mainshait bearing, front. 12. Differential lock. 13. Transfer case cover. 14. Thrust washer. 15. Forward axle bevel pinion shaft. 16. Pinion bearing cage cover. 17. Outer pinion bearing nut.
lB. Pinion bearing cage capscrew.
19. Pinion bearing cage cover seal. 20. Pinion bearing cage. 21. Shims. 22. Thrust washer. 23. Pinion bearing, outer. 24. Pinion bearing spacer. 25. Pinion bearing, inner. 26. Spacer. 27. Differential spider thrust washers, power divider.
2B. Transfer case.
29. Forward axle helical drive gear. 30. Oil seal assembly. 31. Pinion bearing. 32. Pinion bearing sleeve. 33. Pinion bearing sleeve set screw. 34. Power divider to differential carrier mounting capscrew. 35. Power divider to differential carrier mounting gasket. 36. Differential carrier. 37. Bevel ring gear. 38. Differential lubricator. 39. Differential lubricator retaining capscrew. 40. Differential carrier bearing adjuster. 41. Differential carrier mounting capscrew.
*4. Thrust
42. Differential carrier to axle housing mount ing gasket. 43. Axle shaft. 44. Differential carrier bearing. 45. Adjuster lock. 46. Differential case bolt and nut. 47. Bevel ring gear rivet. 48. Differential case, flange half. 49. Differential spide r. 50. Differential spider pinion gear thrust washer. 51. Differential spider pinion gear. 52. Differential case, plain half. 53. Differential side gear thrust washer. 54. Differential side gear. 55. Axle torque arm. 56. Axle housing. 57. Rear-rear axle drive shaft companion flange. 58. Rear helical and side gear thrust washer. 59. Rear helical and side gear. 60. Breather. 61. Differential case (male). 62. Differential spider. 63. Differential case (female). 64. Rear-rear axle helical drive gear. 65. Differential case bolts. 66. Differential spider pinion gear. 67. Front helical and side gear.
6B. Rear-rear axle helical drive gear.
69. Transfer case cover mounting gasket. 70. Transfer case cover. 71. Transfer case cover mounting capscrews. 72. Thrust washer. 73. Drive shaft bearing, inner. 74. Drive shaft nut, inner end. 75. Rear-rear axle drive shaft. 76. Shifter fork. 77. Shift fork bracket mounting gasket. 7B. Shift fork bracket retaining capsc rew. 79. Shift fork lever. 80. Shift fork lever boot. 81. Shift fork bracket.
Rear-rear axle drive shaft outer bearing cover assembly, flange nut and thrust washer are identical with the units on outer end of mainshaft.
NOTE: Rear-rear axle drive shaft inner bearing (73) and nut (74) are identical with mainshaft inne r bearing and nut.
A differential lock is available for the power divider. This locking arrangement is used to lock both the front rear and rear rear axles together and is generally us ed when the vehicle is operating in mud, snow or off the highway.
CAUTION: The differential must not be held in the locked position longer than neces sary. Driving the vehicle on improved or paved roads with the differential lock engaged will subject the axles and gears to unnecessary strain. The differential lock shift fork is spring loaded and automatically releases the lock when shift lever is released by operator.

DISASSEMBLY OF POWER DIVIDER
(AXLE MOUNTED)
12. Using a suitable puller, reInove both front and rear Inainshaft bearings. This COIn pletes disasseInbly of Inainshaft. 13. ReInove the nine transfer case cover re tainer screws. Carefully reInove cover so as not to daInage cover or gasket face of transfer case, as cover Inust be reInoved froIn front bearing of rear rear axle drive shaft. 14. ReInove nut at front end of rear rear axle drive shaft. The cOInpanionflange at rear of shaft should be used to hold shaft while reInoving nut. 15, ReInove COInpanion flange retaining nut and flange at rear of rear rear axle drive shaft. ReInove cOInpanion flange with suit able puller. 16. ReInove the four bearing cover retaining capscrews and reInove bearing cover. 17. ReInove bearing at front end of rear rear axle drive shaft using a suitable puller. Also reInove helical gear retaining washers. 18. Tap front end of rear rear axle drive shaft with a soft haInIner to reInove helical drive gear and spacer. This action will also drive the rear bearing out of case so that the shaft Inay now be lifted out. 19. Place rear rear axle drive shaft in vice having soft jaws and pull the rear bearing off the shaft. The power divider is now cOInpletely dis as seInbled. Place all parts in a cleaning solution to reInove all dirt and sludge deposits. Be sure transfer case is free of any loose Inetal particles. Carefully inspect all parts and replace any that are doubtful as to further satisfactory service ability. To reasseInble the power divider, the exact re verse procedure as outlined for disasseInbly should be used. However, it is advisable to observe the following precautions: Be sure all sealing surfaces are free of nicks and that the old gasket Inaterial has been COIn pletely reInoved. NOTE: The transfer case to differential carrier Inounting gasket is ,ODS" thick. The differential case was Inarked as to for ward side and also for correct reasseInbly of the two case halves. It is of utInost iInportance that the eight differential case Inounting bolts be so installed that the bolt heads are also on forward side of differential asseInbly after installation in power divider. NOTE: FeInale half of differential case should be forward.
To disasseInble the power divider, proceed as outlined in the following steps: 1. ReInove nine power divider to differential carrier Inounting capscrews and lift off the power divider. Be sure Inounting gasket is also reInoved. 2. Place power divider in a transInission stand or other suitable fixture and reInove the four pinion bearing cage Inounting cap screws and reInove pinion shaft cover.
3. ReInove self-locking setscrew in the trans fer case to release pinion bearing sleeve.
4. ReInove pinion shaft outer bearing nut" and using a soft haInIner, tap end of shaft to release pinion bearing sleeve and bearing froIn housing. Withdraw pinion shaft as seInbly froIn transfer case. COInplete dis asseInbly of shaft by reInoving inner pinion bearing, spacer, front axle helical drjve gear and pinion bearing. 5, ReInove pinion bearing cage froIn transfer case. 6, ReInove Inainshaft bearing retainer nut inner end. 7. ReInove cOInpanion flange mounting nut, and using a suitable puller. reInove COIn panion flange and slinger asseInbly.
S. ReInove four bearing cover capscrews and lift off bearing cover.
9. Using a br onze bar, drive inner end of Inain

shaft until shaft passes through rear helical and side gear and thrust washer. This gear and washer can now be reInoved through pinion bearing sleeve opening in transfer case. 10, Continue pushing mainshaft toward front of transfer case until differential case as seInbly and thrust washers are free of shaft. Differential case will also pass through pinion bearing sleeve opening in case. Mark differential case halves so original asseInbly can be duplicated. Keep differential spider thrust washers with differential case to as sure correct reasseInbly. 11. Withdraw Inainshaft all the way. Front helical and side gear, thrust washer and differential lock (where power divi<;l.er is so equipped) can now be reInoved through pinion bearing sleeve opening.
PRINTED IN UNiTEO STATES OF """ERICA
L-LfNE MOTOR TRUCK SERVICE MANUAL
To secure the pinion bearing pre-load reading specified in the Rear Axle Specifications for this model axle, see Pinion Bearing Adjustment for Correct pre-load. Make a bench assembly of bevel pinion shaft, bearings, spacers and pinion bearing cage. Place all parts in the same position as in the final assembly. The pinion shaft assembly may now be placed in the press shown in Fig. 2. After the correct pinion bear ing pre-load reading has been secured remove outer pinion bearing and pinion bearing cage only. The pinion shaft is now ready for install ation. Complete assembly of pinion shaft to transfer case by inserting pinion shaft through pinion bearing sleeve opening until sleeve is in correct position. Install pinion bearing cage, outer pinion bearing, thrust washer and nut. Do not fail to install pinion bearing sleeve set screw after the cone center and back lash ad justments have been made. Use a new bearing cage cover oil seal when completing assembly. After the correct pinion bearing pre-load has been obtained, mount power divider on differ ential carrier. The pinion cone center adjust ment may now be made. Follow procedure set forth under SE-I065 Pinion Setting Gauge. Bear in mind the adjustment of the bevel pinion is controlled by means of a shim pack under the pinion bearing cage at forward side of power divider. The differential assembly may noW be completed and the bevel ring gear adjusted for back lash -- as marked on outer rim of ring gear. Be sure to obtain a tooth contact pattern as outlined under General Rear Axle Hypoid Pinion and Ring Gear Adjustment Point Im pression Method. The differential carrier and power divider assembly is now complete and ready for in stallation in forward rear axle housing. Use a new differential carrier mounting gasket.
BUSHING
11\-16155
Fig. 2
Felt retainer
Nut
Lockwasber
Center Cross Bar

The assembly of the center cross bar and saddle is shown in Fig. 2. The sleeve is lo cated in the saddle and is locked in place by two thru-bolts. Inside the steel sleeve there is a center cross bar, which must rotate freely in the sleeve. In the LF-l 70 the center cross bar is solid steel and on theLF-190andLF-210 it is a steel tube. In removing the tube or cross bar, it is first necessary to jack up the rear end of the truck, remove the spring shackle pins, remove the two equalizer beam end bolts, then remove the saddle, equalizer beam and the springs. The tube or cross bar is then removed from the supporting sleeve.
Felt seal
Lubricato..----i~
Equalizing Beam Ends

Equalizing beam end construction is shown in Fig. 3." The beam end ball is supported in a two-piece bronze socket which is pressed into the beam end. Lock bolts prevent the sockets
A-22712
Fig. 3
L*LINE MOTOR TRUCK SERVICE MANUAL

from moving and felt seals with spring retain ers are used to guard against leakage of lubri cant and entrance of dirt. When replacing a socket or ball, assemble both halves of the socket to the ball and press the assembly into the beam end. Make sure that the grease hole in the socket indexes with the lubricator hole in the beam end - THIS IS VER Y IMPORT ANT. Both sides of the socket must be counterbored flush with counterbore in beam so that the socket lock bolt and plain washers will prevent the socket from shifting. Install felt seals and spring retainers before as sembling the beam end to the bracket. The beam end bolt nut should be drawn up as tight as possible and securely locked with a cotter pin.
,......<?W~b.,.---Cotter pin
Nut Torque rod ball
Torque Rods
Figure 4 illustrates the torque rod end assembly used on six-wheel L-line models. Shims are used between the ball sockets to provide proper adjustment. To disassemble. remove the torque rod ball cap. then tap the torque rod near the bronze socket and the lower half of the socket will slip out. The ball stud nut should then be removed and the ball stud driven out of torque rod.
A22729
Fig.
Reassembly is accomplished in the reverse manner. Press upper half of ball socket into torque rod and insert ball stud. Install shims (approximately .035 11) and insert lower half of socket. Assemble cap and tighten securely. Check movement of ball stud, uS'ing a piece of tubing about 16" long as a lever. If ball stud moves too freely. remove a .005" shim. and if too tightly, add another .005" shim. Only a slight drag should be felt. NOTE: Be sure that the felt seal retainer and spring are replaced to prevent leakage of grease and entrance of dirt.
PRINTED IN UNITED S'fATES OF AMERICA
AXLE-REAR Section H Page 1
ELECTRIC SHIFT (EATON)

USED ON EATON AND TIMKEN TWO-SPEED AXLES
Shifting motor assembly
Switch
receptacle (part of wire .
harness)
A-22894
Fig. I - Electric Shift Unit. speed axle.

Description
Mounted on two
Fig. 2 - Electric Shift Unit Two Way Control Switch

(Figs. 3 and 6) opens the circuit and stops the Inotor when the shifting spring is fully ener gized. Any time thereafter, the shift is COIn pleted by the energy of the spring when torque is InoInentarily rele.ased froIn the differential gears either by releasing the clutch or closing the throttle. A two-speed adapter electrically operated is located at the speedoIneter and is wired in series with the ignition switch (Figs. 2, 3 and 5). The balance of the electrical circuit is also wired in series with the ignition switch, thereby preventing any closed electrical cir cuits in the systeIn when the truck is idle and the ignition switch is turned to the "OFF" po sition.
The electric shift device consists, in the main, of an electrically operated shifting fork and shifting unit located on the two-speed axle (Fig. 1). The shift fork is activated by a two directional coil spring and lever assembly (Figs. 6 and 7). The purpose of this spring and lever asseInbly is to rr.ove the shiftfork quick ly into the high or low speed position when gear load is InoInentarily reInoved froIn the differential. The actual shifting or gear moveInent is perforIned by the coil spring located in the housing of the electric shift unit. The coil spring which perforIns the shift Inust be placed under tension or in a loaded state before gear shift can be accomplished. This is provided for by a reversible electric Inotor which drives a power screw which in turn actuates a drive nut in either direction. Trunnions on either side of the drive nut engage slots in the spring lever. l.1oveInent of the lever in either direc tion energizes the spring which perforIns the shifting InoveInent. The control of the electric shift unit is by means oia two-way switch located on the trans Inission gear shift lever (Figs. 2, 3 and 4). Moving control button up or down causes Inotor at axle shift unit to rotate in either direction. A UInit switch located in the electric shift unit
PRINTEO IN t)NITED STATes OF AM!;RICA
AD
Circuit hreaker
To
ignition switch
Gear shift lever switch
Shift motor
/" -,
'-----.......(.""-----.,:..J
Automatic switch
.,./
\'",
Red
B
C
A22525
------- Black
Fig. 3 - Electric Shift Circuit Diagram

Two-way switch Shifting motor assembly
A-22895
Fig.
- Illustration Of Electric Shift Parts Fig, 5 - Speedometer Two-Speed Adapter

circuit breaker protects the system in the event of a short circuit. Should a short circuit occur, it will open the circuit until the trouble has been corrected.
The system is further protected by a self resetting circuit breaker which becomes operative when normal current flow continues for a period longer than is required to complete .a shift, or in case of an overload or direct short. Details of the various units of the "Electric Shift" their function, and the servicing of each fonows: The switch (Fig. 2) with which the operator controls the axle is located on the transmission gear shift lever. This control switch has two positions -- up and down. Three wires are connected to the switch.. When the selector button of the switch is up, the battery wire (A -- Fig. 3) is con nected to wire (B -- Fig. 3) leading to one field of the motor in the axle shift unit proper. When the button is down, the battery wire is connected to wire (C -- Fig. 3) leading to the other field of the axle shift unit motor and also to the speedometer adapter. As shown in Fig. 2, the control switch is connected to the harness or wiring system by plugging into the three-pronged connector which is part of the harness. The switch is removable by slipping the rubber boot up to the knob and pulling apart.
Speedometer Adapter
The speedometer adapter (Fig. 5) compen sates for variations in the speed of the drive shaft between high and low-speed range of the axle. This adapter is held in the high range by a spring and in the low range by an electro mag net. The inner mechanism is lubricated and sealed for life. but the two shaft ends should occasionally receive a small amount of light oil at the oil-wick cups.
Axle Shift Unit

This unit shifts the axle into high or low range. Fig. 6 shows the axle shift unit in the high range of the axle. In this position wire (b) (Fig. 3) carries current to one field of the motor (6) (See Fig. 20 for Part Identification) so that the armature and drive screw (20) turn in a clockwis e direction and move the nut down. When the nut has traveled a sufficient distance to wind the spring (23). a contact bumper on the nut breaks an electrical connection on the automatic switch (17) so that the motor is no longer energized and the armature stops rotat ing. To make sure that the nut cannot travel back on the screw due to vibration, a ball screw detent spring (Fig. 12) mounted on the cover (26) holds the nut at the end of its travel on the screw. The nut moves the spring winding lever (24) down which pivoting on the pin (21). winds the tors ion spring (23) for high. Thus an in creased load is put on the spring, and in this position the axle is ready to snap into the high speed ratio as soon as the load on the axle gears is relieved. The torsion spring is assembled in the unit so that it is under 45 to 65 pounds pressure, depending on the size of the axle. When the spring winding lever is moved so that the spring is wound, the pressure
Wiring System
The wiring system or harness as shown in Fig. 3 has four terminals. Two of them (b) and (c) in a double line run to the axle shift unit on the axle. Of these the longer red one is con nected to the bottom terminal, and the shorter black one is connected to the top terminal. The short single black wire (c) is connected to the speedometer adapter and the green wire (a) is connected to the circuit breaker. Wire (d) connects the copper stud of the circuit breaker to the cold side of the ignition switch. The
SERVICE AND TROUBLE SHOOTING

screw
General Information
1 the electric shift should fail to operate properly, the trouble should first be located. A very handy tool for this is a test light con sisting of a light bulb, either 6 or 12 volts, depending on the electrical system of the truck, with two wires a few feet long and small battery clips on the ends. Refer now to the wiring diagram Fig. 3 and first connect the test light to Point (d) on the circuit breaker under the dash or hood, depending on the test light to ground. Turn on ignition switch, or accessory switch in the case of a diesel, and the light should show. If it fails to light at this point, there is a poor connection or broken wire between the ignition switch and circuit breaker. Next connect test light to Point (a) on the circuit breaker -- Fig, 3 -- and again the light should show. If it fails to show im mediately, watch the light carefully and listen to the circuit breaker for a minute to see if it is flashing off and on. The light should stay on continuously at this point. If it flashes off and on, or you hear the breaker clicking, it indicates that too much current is flowing and the circuit breaker is opening. This is due either to a short circuit, or the motor in the shift unit not being free to run. To deter mine which of these it is, remove the two wires (b) and (c) from the axle shift unit and recheck. If the light still flashes off and on or you still hear the breaker clicking, it is due to a short in the harness, but if the light now stays on continuously the trouble is in the shaft unit.
If there is no light at all at this point and the circuit breaker cannot be heard clicking, disconnect the green wire from terminal (a) Fig. 3 and again clip the test light to terminal (a) post on the circuit breaker. If the light fails to show here and did show on terminal (d) the circuit breaker is bad and should be re placed. If the test light glowed normally at point (a), next remove the two wires (b) and (c) from the axle shift unit and connect a test light wire to one of these wires and the other test light wire to ground. The red shift unit wire should light the light only in high gear or up position on the gear shift lever switch andthe black wire should light the light only in the low gear or down position of the gear shift lever switch. If the light fails to glow in either of the above tests, it indicates a broken circuit in the har ness or gear shift lever switch. If both wires light the test light in one position of the gear shift lever switch, it indicates a short circuit in the harness or gear shift lever switch.
Limit
switch
Fig. 6 - Axle Shift Unit In High-Range Position
Power
Lever assembly
screw
Drive
nut
----,
Limit
switch
A22893
Fig. 7 - Axle Shift Unit In low-Range Position
of the spring is raised tofrom 90 to 135 pounds again depending on axle size. This additional means is us ed to shift the axle, and when the shift is completed, the ends of the spring come together leaving the origi nal tension of 45 to 65 pounds on the spring. This preload tension holds the axle in either gear.
Shift To Low
When the button is pushed down, the motor is energized so that the screw moves counter clockwise and the nut travels to the top wind ing the spring for a shift to low in the same manner as before.
F"RINTED IN UNITD S"rATE$ 0 ' AMEAICA
Next connect the test light to the speedom eter adapter terminal (c) and ground. Here

to the other battery terminal. The wrench should then tend to turn with a torque or pull of about 6" lbs. Allow the wrench to turn very slowly. making sure that this pull or torque is present the full 360 0 turn of the wrench. If one armature winding of the motor is burned out, this torque will disappear for a small part of the 360 0 While making this test, care should be taken not to overheat the motor. This motor is lubricated and sealed for life.
the light should glow in the low gear or down position of the gear shift lever switch only, 1 it fails to glow, it indicates a broken circuit in the harness or gear shift lever switch. These checks above will quickly locate the trouble. When checking the harness for short or open circuits, watch for broken insulation and do not overlook ~ gear shift ~ switch which can best be tested by substituting a new one in its place.
If the vehicle shifts normally but the speedometer adapter fails to operate properly make the above check with the test light to see if it is getting current in the low range and if it is, replace the adapter. When the trouble has been traced to the shift unit, disassemble as shown under disassembly and inspect the parts carefully. All parts can be washed in cleaning solvent except the motor,
Rubber Diaphragm
The rubber diaphragm between the shift unit and the carrier assembly, which can be seen in Fig. 8 under disassembly, should be in good condition and a tight fit over the shift fork. This diaphragm seals off axle lubricant from the shift unit. NOTE: During reassembly, extreme care should be taken not to allow any dirt to enter the axle shift unit. For correct positioning of diaphragm refer to lettering printed on its face.
When inspecting the parts, most failures will be readily apparent; however, a few assemblies should be checked as follows:
Automatic Switch
The automatic switch (17) Fig. 20 (serv iced only as an assembly) should have clean, free moving points which close firmly under spring tension.
Lubrication
The speedometer adapter requires no more attention than would be required by the speed ometer or the speedometer cable. Several drops of light oil should be applied in the pro vided oil-wick cups.
On the axle shift unit, there is an oil filler plug (27), so marked, provided in the front cover (26) near the bottom. Upon installation, the unit should be filled level with lubricant and should be checked every 10,000 miles or 3 months, whichever comes first, to maintain this level.
Drive Screw
The drive screw (20) Fig. 20 (serviced only as an assembly) should turn freely by ro tating the s crew while holding the nut. When the nut gets to the end of the screw, the screw can continue to turn but the nut should not jam or run off the end. By turning the screw in the opposite direction, the nut will go to the other end and stop as before while the screw can continue to be turned. The fiber bumper in the nut should be a
tight press fit. Be sure in assembly that this
fiber bumper is in towarc:ft'he switch.
Motor
The motor (6) Fig. 20 (serviced only as an assembly) is reversible so that with the motor housing connected t6 one battery terminal and either one of the two motor wires connected to the other battery terminal, the motor will run in one direction. With the other motor wire connected to the battery, the motor will run in the opposite direction. The motor has a stall torque of approximately 6" lbs. The way to check this motor is to put a small crescent wrench on the rectangular drive on the arma ture shaft. Hold the wrench in one hand, hold the motor itself firmly in the other hand or in a vis e and then connect one motor wire to a battery terminal and connect the motor housing
The lubricant us ed should be SAE 10 motor oil, except where temperatures below 0 0 F will be encountered, in which case use 3 parts SAE 10 motor oil to 1 part kerosene. This cold weather mixture can safely be used in temper atures u.p to 32 0 F. To change lubricant, remove front cover Whenever front cover is re moved, care should be taken not to allow any dirt to enter.
(26) and drain.
AXLE UNIT DISASSEMBLY

The axle unit (Fig. 1) is removed from the differential carrier for disassembly and serv icing as follows:
Power screw
Limit
Iwitch
...;.-
fork notch
Axle ,bift usembly
A.22648
Fig, 8 - Remove shift housing to carrier stud nuts and lockwashers and lift off shift unit. Upon reassembly, the swivel block must engage the shift fork notch.
Fig. II - After removal of cover, note that nut and lever assembly will be at either top or bottom of screw, depending upon position in which the shift button was last used.
Fig. 12 - By turning drive screw, run nut from either top or bottom position to center of screw. IMPORTANT: This step is essential to prevent damage to drive nut contact bumper lo cated in center of lower or inner trunnion. The nut must be inthe center position upon assembly also. Fig. 9 - Remove lock nuts and two wires from housing. In reassembling, the long or rod wire goes to the bottom terminal.
Trunnion ( contact bumper
Bearing cover
Fig. 10 - Remove cover screws, lockwashers, cover and gasket. Drain lubricant from housing.
PRINTED IN UNITED STATES OF ".MERICA
Fig. 13 - Pullout assemb I y.
pivot pin and remove lever
NOTE: When reassembling lever assem bly. make certain that the contact bumper on nut is toward the switch.
A-22644
Fig. I~ - Remove drive screw bearing cover and push down on screw assembly until bearing is free of housing. Insert screwdriver in drive slot of screw and remove bearing retainer nut and bearing.
Fig. 17 - Remove" jam" nuts (switch retainer nuts) and fiber washers from back side of hous ing. Remove switch center screw and I ift out switch assembly.
Lever and Spring Assembly

Good practice is to perform the disassem bly and reassembly of the lever and spring unit only when necessary to replace one of the parts.
Turn lever
This lever
Fig. 15 - Remove two lock nuts from switch ter minals and remove wires.
Motor cover
A22649
Fig. 16 - Remove three motor retainer screws, remove cover and gasket, and pul I motor assem bly out of housing.
Fig. 18 - Place lever assembly in vise as shown Turn spring winding lever clockwise and pul I; then al low spring to unwind. This operation will permit disassembly of the leversandspring. IMPORTANT: Do not disassemble this unit unti I necessary to replace one of the parts.
End of spring to be located
SHIFTING INSTRUCTIONS FOR EATON

TWO-SPEED AXLE ELECTRIC SHIFT
TO SHIFT INTO LOW -SPEED RATIO:
1. Keep accelerator pedal down, push button

down.
Z.
To complete shift, disengage and reengage clutch as quickly as possible, holding accelerator pedal down; or release and reopen accelerator as quickly as possible.
TO SHIFT INTO HIGH-SPEED RATIO:
1. Keep accelerator pedal down, pull button up.
Fi g. 19
Z. 1. When reassembling the spring and levers, locate parts as shown (Fig. 19). Turn lever and spring clockwise, bringing end of spring around end of lever nearest vise. Push end of spring into notch of actuating lever nearest vise. This will preload spring. To complete shift, release accelerator and pause until shift is completed.
SPLIT-SHIFTING To shift to next higher gear in the trans mission and at the same time from high to low speed axle, make the transmission shift in usual way and just before engaging clutch push the button down. To shift to next lower gear in the trans mission and at the same time from low to high speed axle, pull the button up, then complete the transmission shift in usual way. IMPORTANT:
Reassembly of the axle shift unit is the reverse of disassembly.
1. Always keep accelerator down when con

tool button is moved, except when split shifting to low-speed r.atio. 2. For best results, start loaded trucks in low-speed ratio.
PRINTE:O IN UNITEO STATES OF AMERICA
!f1'-._ _-1IIr""-- 6
&-12
@--13
~I"
~IS
2S
I-
16
84746
Fig. 20 - Electric Shift Parts Identification List And Illustrations

1. Screw with lockwasher (motor cover to housing). 2. Elastic stop nut (motor to cover). 3. Motor cover cable clip. 4. Motor support and cover. 5. Motor support and cover gasket. 6. Electric motor assembly. 7. Electric motor grommet. 8. Shift motor housing. 9. Jam nut (automatic switch terminal- outside). 10. Fibre washer (automatic switch termi nal -- outside). 11. Bushing (automatic switch terminal hole in housing). 12. Bearing with snap ring. 13. Bearing lock nut. 14. Bearing cover gasket. 15. Bearing cover. 16. Screw with lockwasher (bearing cover to housing). 17. Automatic switch, terminal screws, and base gasket assembly. 18. Flat head screw (automatic switch to housing -- inside). 19. Elastic stop nut (automatic switch termi nals -- inside). 20 Drive screw assembly. 21. Spring winding and shift fork actuating lever shaft.. 22. Shift fork actuating lever assembly. 23. Torsion spring. 24. Spring winding lever assembly. 25. Shift housing cover gasket. 26. Shift housing cover. 27. lI8!! pipe plug. 28. Screw with lockwasher (shift housing cover to housing).
BODIES. CABS &. COWLS Index Page 1
BODY AND CAB GROUP
SECTION "A"
Page
Cab door glass . . . . . . . Cab door glass window regulator. Cab door weather strips . . . . Cab door glas s window channel. Cab rear window glass . . . Panel body rear door glass Windshields . . . . . . Cab door vent glass windo,w Cab door latch and remote control. Removal of outside door handle . . Installation of outside door handle . Lock cylinders and keys Ignition switch. Door lock . . . . Cab door removal. Cowl ventilator Seat adjuster . . Cab mountings . Hood assembly. Fender and radiator grille. Body mountings . . . Fifth wheel mounting. Panel and pick-up body mountings. Windshield wiper . . . . . .
1, 2
2, 3
3
3, 4, 5
. 5, 6
6
6, 7, 8, 9
9. 10
11, 12, 13
13
13
13, 14
14
14
14, 15
15, 16
16, 17
.17, 18, 19, 20
20, 21
.21, 22, 23,24
24
25, 26
27
28 to 33
PRINTED iN UNIYED STATS OF' AMERICA
III
II
R-LINE MOTOR TRUCK SERVICE
BODIES, CABS at COWLS Section A Page I
BODIES, CABS AND COWLS
R-110 to R-184 TRUCKS
A new type centrally located hood latch assembly has been incorporated in the above R-line trucks. Turning the latch handle to its vertical position unlocks the hood permitting it to be raised. Turning both latch handles upward permits removal of the hood assembly.
ers 12-MARCH 19B (Supplemenral page. for erS-II).
PRINTED IN UNITED STATES OF AMERICA,
BODIES, CABS & COWLS Section A Page 1
BODIES AND CABS
Cab Door Glass

The replacement of cab door glass is a simple operation if the following instructions are carried out. TO REMOVE: 1. Remove remote control handle and escutch eon by pressing inward on escutcheon and removing retaining pin from remote con trol handle and shaft (Figs. 1 and 2). 2. Lower door glass and remove regulator handle and escutcheon by pressing inward on es cutcheon and removing retaining pin from regulator handle and shaft (Figs. 3 and 4). 3. Remove door trim panel as shown in Figs. 5 and 6. 4. Remove four retaining screws from door glass bumper (Fig. 7). 5. Remove door-glass bumper through open ing in inner panel. 6. Lower door glass and disconnect glass from regulator .roller. door
Control ass'y.
Fig. I
Pin Handle
Panel
7. Raise regulator arm to extreme upward position to provide working space for fol lowing steps.
Section tbru door inner bandle and remote control
8. 9.
Lower glass to bottom of door and leave resting in bottom of door. Remove door-glass front channel lower retaining screws.
A22B22
Fig. 2
10. Remove door-glass front channel retaining screws at vent-glass window opening lo cated under ends of vent-glass window weather strip (Fig. 8). 11. Lower and position door-glass front chan nel at front of door inside body. 12. Lift door-glass out of door inner panel opening. TO INSTALL: Door glass installation is accomplished by reversing the foregoing removal proce dure.
PRINTED ~N UNITeD STATES 01' AMERICA.
Fig. 3
BODIES, CABS &. COWLS Section A Page 2
Section thru door window regulator haudlt
A-22'24
Fig. q
Fig. 7
Frame channel
Fig. 5
/
Glass
Channel screw
Seal-door window opening belt
Moulding ass'y.-door window opening trim Reinf.-door outer panel window opening
Fi g. 8
Cab-Door-Glass Window Regulator
Panel-door outer Glass & regulator--1!_ _-+....w;-~ channel ass'y. Regulator ass'y. door window
_.!.!.--"""
Section thru do.or window opening at belt

A-2282~
Fig. 6
The cab door-glass regulator should be serviced as a unit either with the door glass in place or with it removed. If it is not desired or necessary to replace the door glass window, the window mustbe lowered sufficiently to dis connect the regulator as outlined on the previous page. Then raise door glas s by hand to its ex treme upward position. Block door glass in this position to facilitate removal of regulator.

TO REMOVE: 1. Remove remote control handle and escutch eon by pressing' inward on escutcheon and removing retaining pin from remote con trol handle and shaft (Figs. 1 and Z). Remove door-glass regulator handle and escutcheon bypressing inward on escutch eon and removing retaining pin from regu lator handle and shaft (Figs. 3 and 4). Remove door trim panel as shown in Figs. 5 and 6. Remove four retaining screws from door glass bumper (Fig. 7). Remove door-glass bumper through open ing in inner panel. Lower door glass and disconnect door glass from regulator roller. Raise door glass to extreme upward posi tion. Block door glass in this position to facilitate removal of regulator. Remove four retaining screws, two above and two below regulator handle shaft (Fig. TO REMOVE:
1. Remove rivet and pull old weather strip from channel.

TO INSTALL: 1. Paint weather strip channel with rubber cement. Z. Insert new weather strip in channel and install rivets.
Z.
3. 4. 5, 6. 7,
Cab Door-Glass Window Channel

The door-glass window channel is held in place by clips, which snap into holes in the upper door frame. The lower portion of the channel is clipped in a removable frame at tached to door inner panel. TO REMOVE:
1. Remove door garnish moulding (Figs. 10

and 6).
Z. Lower door glass with regulator.

3. Remove trim mouldin~ from door glass opening (Figs. 11 and 6).
8.
9).
9. Lower regulator assembly and remove through opening in door inner panel.
TO INSTALL: Door-glass window regulator installation is accomplished by reversing the foregoing re moval procedure.
Fig, 10
Fig. 9
Cab Door Weather Strips

Rubber weather strips are cemented and riveted in cab door opening channel and form a weathertight s~al when doors are closed.
Fig. II

4",

22. Remove door-glass rear channel frame through opening in door inner panel.
TO INSTALL: Cab door-glass window channel installa tion is accomplished byreversing the foregoing reInoval procedure.
ReInove reInote control handle and escutch eon by pressing inward on escutcheon and reInoving retaining pin froIn reInote con trol handle and shaft (Figs. 1 and 2).
5, ReInove door-glass regulator handle and escutcheon by pressing inward on escutch eon and reInoving retaining pinfroIn regu lator handle and shaft (Figs. 3 and 4).
6. ReInove door triIn panel as shown in Figs.

5 and 6.
7. ReInove four retaining screws froIn door glass bUInper (Fig, 7).
8. ReInove door-glass bUInper through open ing in inner panel.
9. Lower door
glass and disconnect door glass froIn regulator roller.
10. Raise regulator arIn to extreIne upward position to provide working space for fol lowing steps. 11. Lower glass to bottoIn of door and leave resting in bottoIn of door.
12. ReInove door-glass fraIne (Fig, 12).
front channel
froIn
13. ReInove two retaining screws at lower end of door-glass front channel fraIne bracket.
14. ReInove door-glass front channel fraIne retaining screws at vent-glass window opening located under ends of vent-glass window weather strip (Fig. 8),
15. Lower and position door-glass front chan nel frame at front of door inside body.
Fig. 12
16. Lift door glass out of door inner panel

opening. 17. Place upper end of front door-glass chan nelframe atfront uppermost corner inside of door, and lower end at lower opposite corner. 18. ReInove door-glass front channel fraIne through door inner panel opening rearInost corner. Spring upper portion of inner panel opening slightly outward atpoint of contact with door-glass front channel fratne to perInit reInoval (Fig. 13).
19. Remove door-glass rear channel and clips

(Fig. 14). 20. ReInove door-glass rear channel through opening in door inner panel. 21. ReInove two retaining screws (one at each end) from door-glass rear channel fraIne.
Fig. 13
BODIES, CABS &: COWLS Section A Page 5
Place chalk line cord in the weather strip flange channel, working the cord into the chan nel around. the full length of the weather strip. Be careful to keep the cord straight and free of kinks {Fig. l6}.
Fig. 16 Fig. lit

Place the cab glass and weather strip assembly in position in the cab opening with the drawing cord protruding to the rear of the opening {Fig. 17}.
Cab Rear -Window Glass Installation

The cab rear -window glass is secured to the cab with a one-piece weather strip in the same manner as the windshield glass (Fig. 15).
Rea~ window glass

Cut this lip away when replacing weather strip Roof inner
Fig. 17
A22722
F j g. 15
Installation of the cab rear window glass necessitates using a length of chalk line cord or a light flexible soft wire. When replacing the rear window glass, a new weather strip should be used. Old weather strips are apt to be stretched or deteriorated and should not be reused when installing new window glass The flange at the window glass opening in the cab must be cleaned free of all old sealing compound or dirt before installing a new glass.
PRINTED IN UNITED STATES OF AMERICA.
While an assistant presses on the inside of the glass to hold it in position in the cab opening, grasp the end of the cord and care fully draw the cord from the flange channel in the weather strip bringing the lip of the channel over the cab flange. Complete this operation around the cab opening to the lower center of the opening (Fig. I8). Leave the one-cord end at the bottom center of the glass, then grasp the opposite end of the cord to complete the drawing operation around the glass to within approximately 6" of COIU pleting the drawing operation. Hold the cord which was first pulled around the edge of the glass in one hand to prevent it being drawn out of position, then carefully pull the opposite end of the cord to complete the drawing operation (Fig. 19).

3, Place the rear door glass and weather strip asseInb1y in position in the rear door opening with the drawing cord protruding to the rear of the opening. 4. With an assistant pressing on the inside of the glass to hold it in position in the rear door opening, grasp the end of the cord and carefully draw the cord froIn the flange channel in the weather s trip bringing the lip of the channel over the rear door flange. COInp1ete this operation around the rear door opening to the lower center of the opening. Fi g. 18 5. Leave the one cord end at the bottoIn center of the glass. then grasp the opposite end of the cord to cOInp1ete the drawing operation around the glass to within approxiInately 6" of cOInp1eting the drawing operation. The cord which was first pulled around the edge of the glass should be heldin one hand to prevent it being drawn out of position, then carefully pull the opposite end of the cord to cOInplete the drawing operatiotl.. 6. Press the weather strip downward and out ward around the door opening to lnsure the seal being fully seated.
In event that the weather strip does not fully engage the contour of the rear door open ing, a sInall aInount of rubber sealing cOInpound can be injected between the weather strip and the rear door to further insure a tight seal.
Fig, 19 Press the weather strip downward and out ward around the cab opening. In event that the weather strip does not fully engage the contour of the cab opening, a sInall aInount of non-hardening sealing COIn pound can be injected between the weather strip and the cab to further insure a seal.
Windshields
The windshield used on the L-line cab is one-piece construction and is a curved glass bent to fit the contour of the windshield opening in the cab. A weather strip fits around the edge .of the glass and is so Inoulded that it secures the glass to the cab windshield opening by fitting over a flange located in the windshield opening on the cab. NOTE: The windshield weather strip shown in the following illustrations is a one-piece weather strip. Production chassis will be equipped with either a two-piece or a one-piece weather strip. However, the one piece weather strip will be provided for serv icing either type. The windshield is installed froIn the front of the cab. In replacing the windshield, it is recoInInended that a new weather strip be used at'all tiInes. A used weather strip is apt to be stretched or deteriorated and should notbe re used when installing new windshields. In the event that a windshield is not daIn aged and it is desired to replace the weather strip only, it is advisable to first cut away the portion of the weather strip which is Inoulded around the flange in the cab (Fig. 20).
Panel Body Rear-Door Glass Installation

The panel body rear door window glass is secured to the door with a one-piece weather strip in the saIne Inanner as the cab rear win dow glass. When Inaking rep1aceInent of the rear door window glass, reInove all old sealing COInpound froIn flange at the window glass opening in the door before installing a new glass. TO INSTALL: 1. Carefully place the Ino1ded weather strip around the edge of the glass. 2. Insert chalk line cord into the weather strip flange channel working the cord into the channel around the full length of the weather strip. Be careful to keep the cord straight and free of kinks.

Windshield glass Cut this lip away when replacing
weather strip
2. Carefully place the moulded weather strip on the glass as shown in Fig. 22.
Front
lflii(
<{
Cowl bar
A-22B9B
Cowl upper panel

Fig. 20
Fig. 22
The operation of cutting away the wind shield weather strip will allow easier removal of the windshield and diminish the possibility of breaking or cracking the glass being re moved. 3. Place a chalk line cord in the weather strip cab flange channel. Work the cord into the channel around the full length of the weather strip, being careful to keep the cord straight and free of kinks. (See Fig. 23.)
Windshield Installation
Procedure for windshield installation on the L-line cabs is as follows:
Wire or cord
1. A rubber sealing compound may have been used when the windshield was installed. This sealing compound will have hardened on the flange of the windshield opening in the cab and should be scraped or cleaned to assure a tight seal upon installation of a new weather strip. Scrape or clean all old sealing compound as shown in Fig. 21.
Fig. 23
4. By means of an assistant, carefully place the windshield with weather strip attached in position in the cab opening. The illus tration shows the cord used for installing the glass terminating at the top of the wind shield. The cord may be installed with the ends at the bottom of the glass. The manu facturer mark or name on the glass is at either of the lower corners of the glass and is generally installed in this position on all windshields of this type. See Fig. 24. 5. With one man working from inside the cab, and the other serving to press the glass inward and to steady the glass from the outside, grasp the end of the cord (either end of cord) as shown in Fig. 25.
Fig. 21
F'RINTED IN UNITD 5TAT5 Of" AMRICA
BODIES, CABS COWLS Section A Page 8
&;

seal, secure the cord which was first pulled around the edge of the glass in one hand to prevent its being drawn out of position; then carefully pull the opposite end of the cord to complete the drawing operation. See Fig. 28.
Fig.
2~
Fig. 26
Fig. 25
6. Carefully draw the cord from the flange channel in the weather strip bringing the lip of the channel over the cab flange. Draw one side of the cord out of the weather strip until the cord has traveled completely around to the bottom center of the glass as shown in Fig. 26. 7. Leave the one end of the cord at the bottom center of the glass, then grasp the opposite end of the cord to complete the drawing op eration around the opposite side of the glass to within approximately 1211 of completing the drawing operation. It is not important which side of the weather strip is drawn over the cab flange first. See Fig. 27. 8. Before completing the drawing operation at the bottom of the windshield weather
Fig. 27
Fig.' 28

During the drawing operation, the man out side the cab must carefully press inward on the glass near the weather strip to assist working the windshield into position while the drawing operation is in process. 9. Upon completion of the drawing operation, the weather strip must be pressed down ward and outward on the sides and upward along the top to bring the weather strip to its seat in the cab opening. In event the weather strip does not fully engage the contour of the cab opening at the corners, a small amount of sealing compound can be injected between the weather strip and cab to further insure a seal at each of the corners. Be sure to wipe away excess sealing compound before it becomes set. See Fig. 29. 5. Loosen door vent screw (Fig. 30).
BODIES, CABS & COWLS Section A Page 9 window adjusting
Fig. 30
6. Remove two door vent glass window hinge retaining screws (Fig. 31).
Fig. 29
Cab Door Vent Glass Window

The cab door vent glass window is held in place by six retaining screws. TO REMOVE: 1. Remove door garnish moulding (Figs. 10 and 6). 2. Remove remote control handle and escutch eon. 3. Remove door glass regulator handle and escutcheon. 4. Remove door trim panel (Figs. 5 and 6),
PR1NTitO IN UNITEO STATES OF AMERICA
Fig. 31
7. Remove door vent glass window. Note: Do not lose thrust washer at vent glass window pivot pin. 8. Remove door vent glass window weather strip (Fig. 32). 9. Remove six door vent glass window cradle frame retaining screws (Fig. 33). 10. Remove door vent glass window cradle frame.
BODIES, CABS lit COWLS Section A Page 10

TO INSTALL: 1. Install door vent glass window cradle frame. 2. Install door garnish moulding. 3. Install door vent glass window weather strip. To facilitate assembling the weather strip the channels engaging the flange open ing should be coated with soap solution and installation started at point indicated in Fig. 34. Press weather strip into vent glass window frame to conform to contour of opening.
,
Fi g. 32 Fig. 31J
4. Install door vent glass window. Note: Be sure washer is positioned over vent glass window pivot pin after vent glass window pivot pin has been installed in weathe r strip.. 5. Install vent glass window hinge lower half on upper half.
Retaining screw
6. Install vent glass window hinge retaining screws. 7. Tighten adjusting screw to provide proper pull tension on vent glass window pivot pin. 8. Install door trim panel. 9. Install escutcheon and door glass regulator handle.
Fig. 33
10. Install escutcheon handle.
and
remote
control

Cab Door Latch and Remote Control
The replacement of a cab door latch and remote control assemoly is a simple operation. The following suggestions will be helpful. The cab door latch and remote control assembly must be removed and installed as a unit. The work can be done either with the door glass removed or in its extreme upward posi tion as described in the instruction for door glass regulator replacement. To remove door latch and remote control assembly after the glass is positioned as out lined above, proceed as follows: 1. Remove remote control handle and escutch eon by pressing inward on escutcheon and removing retaining pin from remote con trol handle and shaft {Figs. I and 2}. Remove door glass regulator handle and escutcheon by pressing inward on escutch eon and removing retaining pin from regu lator handle and shaft {Figs. 3 and 4}. Remove door trim panel as shown in Figs. 5 and 6}. Remove door handle shaft retaining screw cover plug (Figs. 35 and 36).
Fig. 35
5. Remove door lock case shaft cover plug {Figs. 35 and 37} at edge of door inner panel. Remove door handle shaft retaining screw and washer (Figs. 38 and 36). Remove door handle plate retaining screws and door handle (Figs. 39 and 36). Remove door lock case spring retainer and door lock (Figs. 37 and 40).
2.
6. 7. 8.
3. 4.
Panel Plughutton--------_""
Fastener Door Channel Panel-door outer ----..
Section thru door outside handle

Fig. 36
PRINTED IN UNITED STATEiS OF" AMEfUCA
A-228J2
Weatherseal-----.
retaining spring
Fig.
(Fig. 41).
~o
9. Remove five door lock retaining screws

10. Remove retaining screw at lower end of door glass rear channel frame.
Door trim Section at lock cylinder (right side)

A22825
screws
Fig. 37
A-22510
Fig.
Fig. 38
~I
11. Lower door lock assembly to panelopen ing. Rotate lock assembly 1/4 turn counter clockwise to allow removal of door lock from remote control link (Fig. 42).
12. Turn remote control shaft in locked posi tion.

13. Remove three retaining screws from re mote control assembly (Fig. 43). 14. Remove two retaining screws at lower end of door glass front channel frame bracket to allow sufficient movement of channel to permit removal of remote control assem bly as shown in Fig. 44. CAUTION: Do not move channel to the extent distortion is encountered as this will cause interference with door glass operation after reassembly. 15. Remove remote control assembly through inner panel opening.
Fig. 39
Removal of Outside Door Handle

Removal of outside door handle can be easily accomplished as ou.tlined below. 1. Remove door handle shaft retaining screW cover plug (Figs. 35 and 36). 2. Remove retaining screw and washer from door handle shaft (Figs. 38 and 36). 3. Remove door handle plate retaining screws and withdraw dopr handle (Figs. 39 and 36).
Installation of OUtside Door Handle

1. To simplify installation of outside door handle, a simple tool can be made by grind ing a point on the end of a piece of welding rod approximately 1/16" diameter by 6" long, which can be used to pilot the door handle into the door latch mechanism. 2. Insert the tool in the door handle shaft re tainer screw cover plug opening and align tool with door handle shaft installed from opposite side. 3. Install door handle plate retaining screws. 4. Install door handle shaft retaining screw and wasner. 5. Install door handle shaft retaining screw. cover plug.
Fig. ij2
Lock Cylinders and Keys

Fig. ij3
Lock cylinders in ignition switch and door are coded so that the ignition key will operate both. The instrument panel compartment and spare tire lock cylinders requires separate keys. Key numbers should be recorded to facili tate replacement in case they are lost. A code number is stamped on the body of the ignition switch and compartment lock cyl inders, just back of the cap. A code number is stamped on the face of the spare tire lock cyl inder. The door handle lock cylinder does not have a code number stamped on the body inas much as the cylinder is coded to the ignition switch key. To expose the code number on the ignition switch lock, remove the ignition switch cap nut with a small spanner wrench and the number will then be visible. If the compartment keys are lost and the key number is not known, it will be necessary to either drill out the lock cylinder and replace with a new cylinder and keys or replace the complete compartment knob and lock assembly. It is impossible to remove the compartment lock cylinder intact, without the regular key.
Fig. ijij
PR1NTED IN UNfTED STATES OF AMERICA

2. Remove door lock case spring retainer and door lock case assembly (Figs. 40 and 37). TO INSTALL:
1. Position door lock case spring retainer in door.
If the spare tire lock keys are lost and the key number is not known, it will be necessary to replace with new lock assembly.
The ignition switch, door handle and com partment lock cylinders can be removed pro vided the regular key is used. If keys are lost the cylinders must be drilled out, using a 5116" drill, 1/2" to 3/4" deep. This will permit the tumblers to drop out. In case it becomes necessary to replace a lock cylinder and it is desired to use the origi nal key, the tumblers on the new lock cylinder can be coded accordingly. (NOTE: This does not apply to spare tire locks.) This is accomplished by inserting the orig inal key in the new lock cylinder and filing off the tumblers that protrude from' the lock cyl inder body. When doing this, make sure that there are no burrs left on the tumblers and that all filings are blown out with air. Applya small quantity of powdered graphite to the tumblers and insert lock cylinder in receptacle as di rected. Lock cylinders are removed, with keys as follows:
2. Insert door lock case assembly through opening in outer door panel. 3. Align square end of lock case shaft with opening in lock assembly and install lock case assembly. 4. Install door lock case spring retainer into grooves in lock case and snap into posi tion.
Cab Door Removal

TO REMOVE:
1. Remove door glass regulator handle, re mote control handle and door trim panel. 2. Remove door check arm pivot pin (Fig. 45).
3. Remove nuts and washers at upper and low er hinge assemblies from inside of door (Figs. 46 and 47).
Ignition Switch
Remove complete ignition switch from in strument panel. Place key in lock cylinder and insert a piece of wire in the small hole in switch body. Turn key to (right) "On" position and press cylinder retainer down with the wire. The lock cylinder can then be slipped out of the ignition switch body. To install a new lock cylinder, simply push c_ylinder into ignition switch body and turn towards the (right) "On" position until cylinder retainer snaps into place. NOTE: The ignition switch turns to the left or right of the "Off" po sition. When the switch key is turned to the left, all accessories and gauges are "On" but the ignition is "Off". When the switch key is turned all the way to the right, the ignition also is "On".
Fig.
~5
Door Lock
Place key in lock cylinder and insert a piece of wire through the hole in the face of the cylinder. Press spring retainer down with wire, turn cylinder slightly to left and pull out. To replace lock cylinder, insert and turn until retainers snap into place. TO REMOVE: 1. Remove door lock case shaft cover plug (Figs. 35 and 37) at edge of door inner panel.
Fig.
~6
Panel---cowl, inner
Pillar Door hinge plate

t"C----
Spacer
Lower door _----r:;p""\ hinge
Section thru hinge pillar and door at lower binge
A.22820
Fig. It?
4. Relnove door asselnbly.
Cowl Ventilator
The cowl ventilator is controlled by a lever, which is held under tension by springs located at the lever pin and ventilator hinge pin. A rub ber strip celnented in the ventilator trough as sures a weather-tight seal. This type ventilator (see Figs. 48 and 49) requires no adjustlnent or attention other than occasional lubrication of the lever and hinge pins.
TO INSTALL:
1. Position door asselnbly on upper and lower hinges. 2. Reinstall nuts and washers on door hinges. 3. Position door check arln into bracket and install pivot pin. 4. Reinstall door glass regulator handle, re lnote control handle and door triln panel.
TO REMOVE: ADJUSTMENT:
The upper and lower hinges are threaded sufficiently toperlnit adjusting the door towards the front or rear of the door opening. The hinge lnounting holes in the door are oblong to perlnit aligning the door to the cab surface or outer contour and centering the door vertically.
PRINTED IN UNITEO ST,o\TES 0'- "MERIC'"
1. Relnove two ventilator housing capsc rews and sheet lnetal screws (Fig. 48). 2. Relnove ventilator housing (Fig. 48). 3. Relnove four deflector retainin~ -screws. Relnove deflector and SCrep.R {Fig. 48).
BODIES, CABS & COWLS Section A Page 16 4. 5.

from ventilator hinge pin. pin (Fig. 49). 6. Remove hinge
Remove four retaining screws (two on each side in ventilator hinge (Fig. 48). Remove cotter pin, washers and spring
Remove ventilator panel assembly (Fig.
48),
Panel alsembly
Weather Itrip
Housing
A.2282!
Fig. 1+8
TO INSTALL:
1. Place ventilator panel assembly in position through top of cowL

Z.
Control lever
Install ventilator hinge pin, washers, spring and cotter pin. Install four retaining screws (two on each side) in ventilator hinge.
3.
4. Install screen and deflector. 5. Install ventilator housing.
Seat Adjuster (L-110 to L-180)

The seat adjuster assembly is retained in position by eight studs. Four of the stuqs are installed into brackets mounted on the floor board and the remaining studs installed into the seat frame.
Deflector mounting screw
A.22750
TO REMOVE:
Fig. 1+9
1.
Remove seat cushion and seat back cushion.

2. Remove seat adjuster tension spring (Fig. 50).
3. Remove two retaining nuts, washe rs and spacers fromfront of seatframe (Fig. 50).
BODIES, CABS ~ COWLS Section A Page 17
4. Remove two retaining nuts and washers from rear of seat frame (Fig. 50). Remove seat frame assembly.
5. Remove four retaining nuts and washers from brackets mounted on floor board.
6. Remove seat adjuster assembly.
NOTE: Either left or right adjuster assembly can be removed individually after removal of the adjuster assembly retainer nuts and washers (bracket to adjuster). Move the adjuster assembly to its extreme rearward position to permit disengagement of the equalizer pinion teeth from the pinion rack,
TO INSTALL: Seat adjuster installation is accomplished by reversing the foregoing procedure. The seat adjuster rack should be cleaned with a commercial solvent and lubricated with non-hardening lubricant periodically in order to obtain the maximum efficiency.
Fig. 50
Cab Mountings
Reference to the various drawings of cab mountings will reveal their construction de tail s. Mountings illustrated in Figs. 51, 52, 53, 54,55,56 and 57 should be assembled as shown and the mounting nuts tightened to slightly compress the insulators. Install cotter pins for mountings illustrated in 52 and 57.
Seat Adjuster (L-190 up)

The seat adjuster assembly used on the driver'S seat on the above models is similar to the seat adjuster used on L-110 to L-lBO models. Therefore the removal and installation instruction outlined for L-ll 0 to L-lBO models can be followed.
Inner bracket
Outer bracket
r;=:=:;:'t'III-- Floor front
crossmember
l ' I i f - - - Mounting bracket
Front view
FRONT MOUNTING
L
-
Side view
=:..::::::=::::
=-=- ---:~=====:::i
Fig. 51 - L-IIO, L-120, L-130 Series

opr
AMERICA
Insulator Retainer Wasber
Frame
rail~ jL.-.-i
REAR MOUNTING
A-22650
.'::-, ~....)
y
I
Crossmember
Fig. 52 - L-IIO, L-120, L-130 Series

Inner bracket Outer bracket Floor front crossmember
Trunnion bracket
I
A-22659
Front view
FRONT MOUNTING
Side view
Fig. 53 - L-150, L-160, L-170, L-ISO Series

=- Floor rear erou siD ~===-==-==""'=
Spacer (L-IS4 only)
~~~~~LL
(
~support
Fr~ ~ai1 ~~~-~dJJ~l~:-====l
II
Croumember---.lJ
Side view
REAR MOUNTING
Fig.
5~
- L-150, L-160, L-170, L-ISO Series
Floor front crossmember
Insulator
Front view
FRONT MOUNTING
Side view
A22810
Fig. 55 - l-190, L-200, l-210, L-220, l-230 Series
CrolSmember --*1
I I
Crossmember
view
REAR MOUNTING
Rear view
A-22823
Fig. 56 - l-190, l-200, L-210, l-220, l-230 Series

PRINTED IN UNITEO STATES Of" AMERICA

Washer Floor rear crossmember
Insulator Retainer Cab sub-frame angle
--~~,.
r=
I
-.t----
Spring
Cotter pin
-~
t 1
=-1
Washer --+--~9'f'=Ffb
.~.
FRONT MOUNTING
REAR MOUNTING
A-22738
Fig. 57 - LC-160, LC-180 Series

Hood Assembly (Lll0 to L-180)
The hood assembly is hinged on both sides of the fender side shields. Turning the hood latch handles upward on either the left or right side of hood will permit raising the hood assem bly. TO REMOVE: 1. Release hood latch on both sides of hood by turning handles upward. Remove hood assembly. 2. Remove 10 hood latch retaining screws and lockwashers and remove hood latchassem bly (Fig. 58). TO INSTALL: 1. Install hood latch assembly to hood using 10 retaining screws and lockwashers. 2. With hood latch handles turned up, position hood assembly over hinges located on fend er side shields and turn hood latch handles down to lock hood assembly. ADJUSTMENT: 1. Remove hood assembly. 2. Loosen hinge retaining screws at brackets and fender side shields (Fig. 59).
Hinge retaining screws

A-22726
Fig. 58
Fig. 59

3.
The hood hinge mounting holes in the hinge mounting brackets and fender side shields are considerably larger than the mounting bolts to permit adjustment of the hinge brackets and alignment of the hood.
4. Remove three wires from horn relay and pull horn wire towards the front of truck between the fender splash shield and radi ator frame support. Mark wires for re assembly.
4. Loosening hood latch retaining screws (Fig. 58) will permit aligning hood latch to hood hinge s.
5. Pull head lamp wiring harness towards the rear through fender splash panel and re rrlOve all harnesses from the three clips located on fender side shield (Fig. 61).
Hood Assembly (L-190 up)

The hood assembly is hinged in the center and attached to the cowl and radiator shell by retainers. TO REMOVE: 1. Release hood latch on both sides of hood by turning handles upward.
6. Remove two grille retaining screws, nuts

and cotter keys from bracket located on front crossmember.
Z.
Remove retaining screws and lockwashers from hood end of prop assembly.
3. Remove retaining nuts and lockwashe rs from hood hinge retainers. 4. Remove hood assembly. TO INSTALL: 1. With hood latch handles turned up, position hood assembly over cowl and radiator shell.
Fig, 60
2. Install hood hinge retainers to hood hinge, cowl and radiator shell.
3. Install hood prop assembly and retaining screws to hood. ADJUSTMENT: Hood adjustment is accomplished by loosen ing the hood hinge retainer nuts and radiator shell stay rod nuts at brackets mounted on cowl and shortening or lengthening stay rods by re adjusting retaining nuts.
Fender and Radiator Grille (L-110 to L-160)

The fenders and radiator grille are readily removed as a complete unit by following the procedure as outlined: 1. Remove hood assembly.
Fi g. 61
7. Remove fender brace retaining screw (both sides) from cab (Fig. 62).
8. Remove four fender stone deflector to cab retaining screws on both sides (Fig. 62).
Z.
Remove head lamp wiring harness termi nals from junction block on grille brace (Fig. 60). Mark wires for reassembly. Remove head lamp wiring harness from clip located on leH side of grille brace (F ig. 60).
PRINTED IN UNITED STATES 0,," AMERICA
3.
9. Remove fender to cab retaining screw and

two cab to fender retainin~ screws from inside of cab on both sides (Fig. 62).
BODIES, CABS &: COWLS

Section A Page 22

3. Remove head lamp WIring harness and junction block ground cable from clip to cated on left side of grille brace (Fig. 64). 4. Remove three wires from horn relay and pull horn wire towards the front through fender splash panel. Mark wires for re assembly.
Fig. 62
10. Remove two fender side shield to cowl re taining screws on both sides (Fig. 63). 11. Remove front end section as a unit. complete 5. Pull head lamp wi,ring harness towards the rear through fender splash panel and re move all harnesses from three clips lo cated on fender side shield (Fig. 65).
Fig. 61l
Fig. 63
Fenders and Radiator Grille (L-170 and L-180)

Fig. 65
The fenders and radiator grille are readily removed as a complete unit by following the procedure as outlined: 1. Remove hood assembly and drain radiator. 2. Disconnect the head lamp. parking lamp and ground wires at the junction block on grille brace. Note identification numbers on wire for reassembly (Fig. 64).
6. Disconnect radiator hose clamp at radiator

inlet. Pull radiator forward to facilitate removal of radiator support frame rubber pads (Fig. 66). 7. Remove the two front retaining nuts and washers (both sides) from radiator frame support pads (Fig. 66).
Fig. 66
8. ReInove two grille crossIneInber retaining screws at fraIne rail (Fig. 67). (Illustra tion shows bUInper reInoved to secure better view of operation.)
Fig. 68
~;d~~ side shield F

to cowl retaining
Fig, 67
Fig. 69 Fender and Radiator Grille (L-190 up)
9. ReInove fender brace retaining screw (both sides) froIn cab (Fig. 68). 10. ReInove four fender stone deflector to cab retaining screws on both sides (Fig. 68). 11. ReInove fender to cab retaining screw and two cab to fender retaining screws froIn inside of cab on both sides (Fig. 68). 12. ReInove two fender side shield to cowl re taining screws on both sides (Fig. 68). 13. ReInove front end section as a cOInplete unit.
PRINTED IN UNITED STATES Of" AMERICA
The fenders and radiator grille are readily reInoved as a cOInpiete unit by following the procedure as outlined: 1. ReInove hood asseInb1y AND DRAIN RADI ATOR. 2. ReInove radiator shell stay rods. 3. Disconnect radiator hose at radiator inlet. 4. ReInove radiator fraIne support pad rear retaining nuts and washers on both sides of radiator (Fig. 70).
5, Loosen radiator frame support b:r:acket retaining nuts at radiator shell to facilitate removal of brackets from radiator frame support pads (Fig. 70). 6. Remove two grille to bracket at cross member retaining screws and pads.
Fig. 72
Body Mountings
When mounting bodies on frames always place tight-fitting spacer blocks inside the frame channels at points where the U-bolts are to be installed. These filler blocks will support the frame flanges and prevent bending by the U-bolts. The filler blocks -should be so constructed that they will be form fitting in the channel and so constructed that the body U-bolt will rest in a recess in the block to prevent its loss should the bolt become loose. Fig. 73 illustrate s the construction of such a block. Well-seasoned wood should be used for filler block construction.
Fig. 70
7. Remove three bracket to fender retaining screws on both sides (Fig. 71).
Fig. 71
~~~U-bolt
8. Remove the three head lamp feed wires from junction blocks on both fender side shields (Fig. 72). 9. Remove front end section as a complete unit.
........1 1 - - - - -
Block
Plate
A22786
~g~~ ....... ~---
Fig. 73

FIFTH WHEEL MOUNTING FOR TRACTOR AND TRAILER COMBINA TIONS
Correct fifth-wheel mounting requires at tention to two major factors--first, proper attachment of fifth-wheel unit to frame, and second, correct fifth-wheel king-pin location with respect to the centerline of the rear axle. Determination of the proper position involves consideration of several distinct factors and for full details, reference should be made to Sales Engineering Bulletin No.9 (CT-Z09), dated October 1946. Subsequent paragraphs describe general details of satisfactory fifth-wheel installations.
Fifth wheel sub-sills may be either of wood or angle iron construction and should always extend to within 1" from the back of the cab. Wood sub-sills (Fig. 74) should be of either kiln dried oak or white ash and the same width as the frame rail. Notches should be cut into the sub-sill to provide clearance for frame cross member rivets or other obstructions. Wood sills of less than 4" in height should not be used. Angle iron sills (Fig. 75), where desired, should be constructed in accordance with the following chart:
Mounting plate Mounting plate Wood sub sill
Minimum 4" ----lI~: U bolt Frame rail---__~~ Leave boles for taillight wire and brake line
U bolt
Leave holes for taillight wire and brake line
~
7~
Angle iron (weld securely to frame rail)

A-22788
Fig.
Angle iron sub sill
Angle iron to extend full length of mounting plate
A-22704
Fig. 75
BODIES, CABS & COWLS Section A Page z6
Sub liD t. ellend 1" back .1 cab
Filth wheel
Frame rail I
1"
C.nter line 01 rear ad. Center line of 61tb wbeel
",I (E--- Back 01 cab

O
Sub ,ill
rr;:
, /
Filth wheel
Mounting pial.
;/
U bolt
/'
Fi g. 76
A-22827
For I-liZ to Z ton tractors--Use angle iron 3/8 11 X 3 ft X 3" For Z-1/2 to 3 ton tractors--Use angle iron lIZ 11 x 3 -l/Z II x 3 -l/Z II For 5 to 7 ton tractors--Use angle iron 5/8" x 3-lIZH x 3-1/Z" . Fifth wheel mountings are generally re
ferred to as being either IIhigh-type ll or "low
type". "Intermediate" or flrnedium" mountings
are obtained by using variations of the I1low type" l'ftountings.
ri~. 76 illustrates top and side view of a

fifth wheel mounting to show relative position
of the fifth wheel king-pin to the center line of
the rea r-axle.
flange as shown. Construction detail of wood spacer blocks is also shown in Fig. 74 and it must be noted that the direction of the wood grain is vertical. CAUTION: Do not drill holes in frame rail or remove rivets.
Steel spacers (lower spacer to run full length of mounting plate)
~ Mounting plate
U bolt plate .....C~:;;:==~;::::::J

Ubolt---~
Angle iron lub liII (to extend to I" back of cab) Angle iron 3 It 3 '/,/ weld securely to (,ime rail
The "high-type'! mounting is shown in Fig. 76. Fig. 74 illustrates installation details and
instructions for "high-type" mountings.
Fig. 77 illustrates an adaptation of the tllow type" mounting to provide a medium height.
Optional use of angle-iron and wood frame channel spacer blocks is illustrated in Figs. 74 and 75 and may be used in any type mounting. The angle-iron spacers where used should be tack-welded (electrical preferably) to the frame
leave clearance for
tail ligbt wire
and brake line
A-!l281l
Fig. 77

Panel and Pick-Up Body Mountings
The panel and pick-up bodies are secured
to frame rail by mounting pads, screws, nuts and lockwashers. Figs. 78 and 79illustrate the construction of such mountings.
Floor front crosamember
InSulat:~ . , Mounting
pad
11
/> -
l~ame rail
~/~
o~l -=--U)
bracket
Front mounting
Rear mounting
PANEL BODY (LBO, Ll20)

Fig. 78
A-22815
Frame rail
~ ~- - -=-~-==~~"-=~=-=-='
~ ,
~=-=-~-==-~~~~~=9
PICK-UP BODY (LHO, Ll20)

Fig. 79
PRINT!O IN UNITl!tD STATES OF AMERICA
A-22819
WINDSHIELD WIPER "TRICO" (L-110 to L-160)

The windshield wiper rrlOtor, shafts and links assembly is readily removed providing the procedure outlined is followed: 1. Remove wiper link retaining clips at wiper motor shaft lever (Fig. 80). 2. Disconnect links from wiper motor shaft lever (Fig'. 80), 3. Remove two windshield wiper motor retain ing screws (Fig. 80). Lower wiper to fa
cilitate next steps. 4. Loosen switch control cable retaining screw (Fig. 81). Remove control cable. 5. Remove vacuum hose from windshield wiper motor. 6. Remove windshield wiper motor. 7. Remove windshield wiper arms and blades. 8. Remove two windshield wiper arm shaft retaining nuts (Fig. 81). 9. Remove two windshield wiper arm shaft caps and gaskets (Fig. 81). 10. Remove windshield wiper arm shafts and links as an assembly.
Control cable screw

A-22707
Fig. 81
WINDSHIELD WIPER (L-170 up)

"AMERICAN BOSCH - WWB6A"
The windshield wiper motor is readily re moved as a complete unit by following the pro cedure as outlined. TO REMOVE: 1. Remove windshield wiper arms and blades. 2. 3. Remove retaining nuts from windshield wiper arm shafts (Fig. 82). Remove windshiel.d wiper arm shaft caps and gaskets.
TO INSTALL: The windshield wiper motor, shafts and links assembly installation is accomplished by reversing the above procedure.
Lubrication
The windshield wiper arm links should be disconnected at the wipe r motor and link sockets lubricated periodically with a light grade of machine oil (SAE-IO).
Fig. 82
4. Remove two windshield wiper retaining screws, nuts and washers (Fig. 83).
Motor
Unk retaining clip,s

5, Remove four link arm spring retaining clips and washers from windshield wiper motor and windshield wiper arm shafts and remove link arms. 6. Remove windshield wiper motor (Fig. 84).
Motor retaining screws
Fi g. 80
7, Remove windshield wiper electrical cables (Fig. 84). The terminal posts on the wind shield wiper motor are marked "F", "A",

and "F" to facilitate reassembling the har ness wires. The wires in the harness are coded according to colors. The wire col ored "Red tt is to be installed in terminal post "F"; the wire colored "Black" is to be installed in terminal post !fAIf; and wire colored HGreen" is to be installed in ter minal post IfP". TO INSTALL: Windshield wiper installation is accom plished by reversing the above procedure.
BODIES, CABS & COWLS Section A Fage 29
Lubrication
The windshield wiper arm links should be removed periodically and link sockets dipped in machine oil (SAE-IO).
CAUTIONI (INSTRUCT CUSTOMER)

Do not attempt manual movement of the blades or arms of a wiper that is not equipped with clutches. To do so will cause damage to the wiper arm shaft serrations and possibly other related parts.
Fig. 83
When cleaning the windshield, always em ploy the standby feature of the wiper arm which lifts the blade clear of the windshield.
Fig.
8~
PRINTED IN UNITED STA.TES OF "'hfERICA
L-LiNE MOTOR TRUCK SERVICE MANUAL
DUAL ELECTRIC WINDSHIELD WIPERS

(AMERICAN BOSCH)
TYPE WWB
Fig. 85
Item No.
Description
Item
No.
Description
Item
No.
39. 40. 41. 42. 43. 44. 45. 46. 47. 48. 49. 50. 51. 52. 53. 54. 55. 56. 57. 58. 59. 60. 61.
Description
1. Screw, gear housing cover. 2. Cover, gear housing. 3. Gasket. cover. 4. Nut, gear shaft and crank arttl assembly. 5. Washer, lock. 6. Washer, plain. 7. Plate, drive gear. 8. Gear, right. 9. Gear, left. 10. Washer, spacing, fibre. 11. Washer, spring. 12. Nut, thru-bolt. 13. Housing, gear, right. 14. Housing, gear, left. 15. Shaft and crank-arm gear, right. 16. Shaft and crank-arm gear, left. 17. Washer, link assembly. 18. Link assembly. connec ting.
19. Clip, spring.

20. Shaft and crank-arm,
wiper arm. 21. Washer, spacing. 22. Stud assembly, wiper arm. 23. Spacer, inner. 24. Washer, spacing. 25. Ring, spring. 26. Washer, sealing. 27. Spacer, outer. 28. Nut, fastening. 29. Screw and lockwasher. 30. Bracket assembly. 31. Strip, insulation. 32. Strip, insulation. 33. Coil, field. 34. Shoe, pole. 35. Screw, pole shoe. 36. Housing assembly, motor. 37. Name plate. 38. Washer, spacing.
Washer, insulation. Armature. Cable, brush holder. Washer, spacing. Spring. Brush, carbon. Grommet. Bolt, thru -. Switch, parking. Screw, parking switch. Sleeve, insulation. Terminal, cable. Resistor. Washer, insulation. Washer, plain. Washer, star. Screw, fastening. Arm, wiper. Adapter, wiper arm. Nut, wiper arm. Blade, wiper. Knob, switch. Switch, manual.

DUAL ELECTRIC WINDSHIELD
WIPERS (AMERICAN -BOSCH TYPE WWB)
General Description
The American Bosch WWB dual electric windshield wiper is a two-speed, unit designed to simultaneously operate two arms and blades in either a parallel or opposed wiping motion. The electric windshield wiper consists of the following components: Motor assembly.
Two connecting link assemblies.
Two wiper-arm shaft and crank-arm
assemblies.
Mounting bracket. .
Manually operated switch.
This new dual wiper is available for 6 and 12 volt installations (See Fig, 85) and incorpo rates the following features: 1. Dual speed shunt wound motor,
Fig. 86
Disassembly
1. Before removing the motor assembly from the vehicle and with the wiper blades parked, carefully note the relative positions of the crank-arms which are part of the gear shafts (15 and 16), This is necessary in order that the correct wiping motion and parking of the blades is retained following reassembly,
2. Double extension type, armature shaft with

a single thread worm at each end.
2. Remove the connecting link assemblies (I 8)

froIn the gear shafts and crank-arms and re move the motor assembly from the vehicle.
3, Self-aligning bronze bearings.
4. Two-speed control located in manually op

erated three-position switch (61).
3. Remove the gear housing covers (2) and gaskets (3).
5, Thermostatic overload circuit breaker lo cated on manually operated switch.
4. Remove the
gear shaft and crank-arm fastening nuts and tap out both assemblies from the gear housings.
6, Low current draw:

(a) Approximately 4.0 amperes at 6-volts and 2.0 amperes at 12-volts (depending on load) in low-speed position.
(b) Approximately 3.0 amperes at 6-volts and 1.5 amperes at l2-volts (depending on load) in high- speed position.
5. Remove both thru-bolts (46),
6. Remove the right (R) gear housing (13) from

the motor housing (36) being careful not to remove the armature (40), This can be ac complished as follows: (a) Set the motor assembly in an upright position on the left (L) gear housing (14).
7.
Wiping angles from 85 0 up to 118 0 ,
8. Automatic parking switch (47). This switch is connected in parellel with the manual switch when the latter is in the nOFF!! po sition. The wiper motor will continue to operate until the cam located on the gear shaft (16) engages the parking switch button. Also refer to Fig, 86
(b) Grasp the motor housing in the left hand.

(c) Carefully remove the right gear ing (13) with the right hand and same time maintain a downward sure on the armature with the finger.
minal of the parking switch (47). hous at the pres index
9. Four parking positions for the wiper blades:

(a) Right or left hand (parallel wiping mo tion). (b). Inboard or outboard (opposed wiping motion).
PRIN'fD IN UNITED STAT.E9 OF AMERICA
7. Unsolder the field lead from the "Fit ter
8. Remove the left (L) gear housing (14) and

armature, as a unit, from the motor hous ing (36).
BODIES, CABS & COWLS Section A Page 3Z

Lubrication
GEARS (8 and 9) AND GEAR HOUSINGS (13 and 14): 1/3 full of US 515 grease - spread over gear teeth and worm. ARMATURE SHAFT BEARINGS: Z or 3 drops of SAE-lO oil in surrounding felt.
9. Hold both brushes (44) clear of the commu tator so that they do not rub on the arma ture shaft and worm, and remove the arma ture from the gear housing. The brushes must be kept free of grease at all times.
Cleaning
All parts except the field coils (33), arma ture (40) and parking switch (47) should be washed in a good commercial cleaning solvent. Bearing equipped parts should be washed with a brush dipped in a good commercial cleaning sol vent taking care that as little as possible of the cleaning fluid comes in contact with the bearings. DO NOT I1tftv1ERSE BEARING EQUIPPED PARTS IN A CLEANING FLUID. Thoroughly dry all parts that have been washed in the clean ing fluid. The fie ld coils, a rmature and parking switch may be wiped with a clean dry cloth or com pressed air may be used if available.
GEAR SHAFT AND CRANK-ARMS (15 and 16): Fill recessed section of shafts with US 515 grease. CONNEC TING LINK ASSEMBLY BEARINGS (18): Several drops of SAE-IO oil. STUD ASSEMBLIES (ZZ): Fill space between bushings with US 515 grease.
Reassembly
Reassembly is accomplished in the re verse order of disassembly up to and including the reassembly of both thru bolts to the motor housing. The gear shafts and crank-arms (15 and 16) are reassembled to their respective gear housings as follows: 1. Reassemble the <gear drive plate (7) to the gear (8 or 9). Z. Replace either the right (R) or left (L) gear shaft and crank-arm in the correct position.
Inspection
ARMATURE (40) Check the armature insulation by applying allO-volt (60 cycle) test lamp between the com mutator and armature shaft. HOUSING AND FIELD COIL ASSEMBLY Check the resistance ofthe field coils with an accurate ohmmeter. The total field coil re sistance of a 6-volt wipe r is approximate ly 2.8 ohms; of a lZ-volt wiper, approximately 11.Z ohms. GEAR HOUSING AND BRUSH HOLDER ASSEMBLY (14) Check the insulated brush holde r by applying all O-volt (60 cycle) test lamp between the brush holder and the gear housing. BRUSH SPRINGS (43) Brush springs with afree length of less than 1 n should be replaced. BRUSHES Damaged brushes or brushes worn down beyond 213 of their overall length must be re placed. Examine all other parts for damage and wear; replace as necessary.
3. Carefully reassemble the spring washer (11) and spacing washer (10) to the large diam eter of the gear shaft.) 4. Line up the flat on the shaft with the flat on the gear drive plate, then drop the gear drive plate (7) and gear (8 or 9) in place on the shaft. 5. Secure the assembly with the plain washer (6),lockwasher (5) and the fastening nut (4). 6. If the position of the crank-arm shifted during the above procedure, reposition by turning the armature shaft as required. 7. Reassemble the remaining gear and crank arm into its gear housing in accordance with instructions in items I to 5. 8. Before securing the assembly, make certain both crank-arms are in correct relation to each other. If a correction is necessary, proceed as follows: (a) Remove the gear drive plate (7) and gear (8 or 9). (b) Reposition the crank-arm until it is in correct relation to the other.

(c) Reassemble the gear and gear drive plate to the shaft and secure the as sembly as in item
Ii such is the case, pull the wire from the liB" terminal at the control switch and "snap" or ''flip'' the switch button to break it loose. The parking switch is provided with an ad justment feature to permit close adjustment of the parking position of the wiper blades. This adjustment has been made at the factory and should not require change. A clamp screw (Figure 2) holds the parking switch assembly in position after adjUStment. The overload circuit breaker, located in a 6 volt manually operated switch (61), should carry approximately 10 to 12 amperes before opening; and in a 12 volt switch, approximately 5 to 6 amperes before opening. CAUTION: (Instruct Customer) Do not attempt manual movement of the blades or arms of a wiper that is not equipped with clutches. To do so will cause damage to the wiper arm shaft serrations and possibly other related parts.
Testing
Before installing the motor assembly in the vehicle, check the operation of the assembly as follows: 1. Temporarily connect either the plus (+) or minus (-) terminal of a battery to the mo tor housing. The battery should be fully charged and of approproate voltage. 2. Temporarily connect a "jumper" between the HA" and IIF" terminals on the motor te r minal plate (See Fig. 86). 3. Connect the remaining battery terminal to "All on the motor terminal plate; this will result in the low speed operation of the motor. At this speed the c rank-arms should revolve at approximately 45 cycles per min ute. 4. To check high speed operation, remove the battery connection from terminal HA" on the motor terminal plate . 5. Remove the temporary "jumper" from ter minals "A" and HF" on the motor terminal plate.
6. Re connect the batte ry to te rminal "At! on the motor terminal plate. This should result in the high speed operation of the motor. At this speed the crank-arms should re volve at approximately 65 cycles per min ute. The parking feature of the wiper should be :::hecked after the motor assembly has been re mounted on the vehicle and the connecting link 3.ssemblies (18) replaced on the gear shafts. The wiper should be operated thru the manual switch (61). There have been instances where the elec ;ric windshield wiper has continued to operate l.fter the switch has been turned to the I!OFFII )osition. This is caused by the parking switch Jutton shoe or cam located on the left hand shaft md crank assembly to break the circuit. To >vercome this complaint, the show (Fig. 2) ,hould be carefully bent towards the switch only mough to bear harder against the switch button lUt not contact or rub against the switch body. rhe shoe must be parellel to the face of the ;witch body.
In event the windshield wiper will not start rom the parking position after the switch is unned "ONII, the switch button should be checked o see if it is stuck in the depressed position.
PRINTED fN
UNIT~O
STATE:S
or
AMERICA
BRAKE SYSTEM Index Page 1
BRAKE GROUP
SPECIFICATIONS: Air brakes . Hydraulic brakes
INDEX
Page
6,7
1,5
SECTION "A"
HYDRAULIC BRAKE SYSTEM: Bleeding lines . . . Brake pedal adjustment. Care . . . . . . . . . . . Check valve . . . . . . Hydraulic brake sys tern. Hydraulic fluid . . . . . Maintenance hints . . . . . . . . . Mas ter cylinder.' . . . . . . . . Repairs to mas ter cylinder and wheel cylinders. Wheel cylinders . . . . . . . . . . .
3 2
2
2 1 1
3,4,5
1 2 2
SECTION .. B'
HYDROVAC POWER BRA.KE UNITS: Bleeding ins tructions . . Description . . . . Hydrovac air inlet filter Hydrovac check . . . . Illus trations . . . . . . . Lubrication . . . . . . Vacuum connection service . Vacuum line oil bath air cleaner.
4
5
6,7
1,2,3 .4 5 5
SECTION "C"
AIR BRAKE SYSTEM: Air brake equipment. Operation: Charging. Release. Service application . Ins truc lions . . . . . . Preventive Maintenance and Trouble Shooting: Air leakage tes t. . Inspection . . . Operating tes ts .. Service . . Trouble shooting Air pressure gauge. . . . Brake chamber (Bendix-Westinghouse). Brake chamber - piston type (Midland). Brake valve . . . . . . Brake valve - hand operated. Cut-out cocks . . Double check valve . . . . .
F>RINT!O IN UNITEO STATtS 0" AMERICA
1,2
2 2
2 2,3
4
4 4
3,4 5 14 12,13 13,14 5,6
6,7
14 . 8 ( Continued)
BRAKE SYSTEM
Index
Page 2
BRAKE GROUP (CONTINUED)

AIR BRAKE SYSTEM, SECTION "C" - CONTtD: Drain cocks . . . . . . . . ~ Governor (type 0-1) . . . . . . . . . Hose and hose connections. . . . . . . . . . . . Hose coupling and dummy couplings. . . . . . . . . . . . . . Low pressure indicator . . . . . . . . . . . . . . . . , Quick release valve ..... R ela y valve.. .. . . . , . . . .. . .. . .. . .. .. . . . . . . .. . . . .. . .. . .. . . . . . Reservoirs ............. ..... Safety valve ............. ... " .............................................. Slack adjus ter ............... Stop light switch. Tubing .... ,.
lit lit ...
lit .... lit .. " ... ..
Page 15
8,9
. . . . . . . .. ............
..
lit
.......................................................................
.. . . .. .. .
It .. .
.. lit ......
lit
................
lit
..................................
It
...................................................
(>
......................................
lit
.....................................
15,16 17 11,12 7,8 8 14,15 9,10 10,11

12 17
BRAKE SHOE ADJUSTMENTS AND SERVICING SECTION "0"

L-llO, L-lll, L-1l2, L-120, L-121, L-122 Adjustment for wear (minor) . . . . . . Major adjustments and servicing. Parking brake cable adjustment . . . . . . .
2
2,3 2,3
SECTION !fE"
LM-120. LM-121, LM-122 Adjustment for wear (minor) . . . . . . . . . Major adjus tments and servicing. . . . .
2
2,3
SECTION "F"
L-130, L-131. L-132 Adjus tment for wear (minor) . . . . . Major adjus tments and servicing.
2
2,3
SECTION fiG"
LB-140 Adjus tment for wear (minor) . . . . . . . . Major adjustments and servicing. . . . . Parking brake cable adjustment . . . . . . . 2 2,3 2,3
SECTION "H"
L-150, LM-lSO, LM-lSl Adjustment for wear (minor) . . . . . . Major adjustments and servicing. . . .
2
2,3,4
SECTION Ifl"
L-lSl, L-lS2. L-IS3, LM-1S2 Adjus tment for wear (minor) Major adjustments and servicing.
2
2,3,4
BRAKE SHOE ADJUSTMENTS AND SERVICING (CONTINUED) SECTION "J"

L-160,L-161,L-162,L-163,L-164,L-165,LC-160,LC-161,LC -162.L-170,L-17I,L-I72
L-173,L-174,L-175,LF-170,LF-17I,LF-I72 - FRONT BRAKE 12-1/8"x2-1/4 (TYPE "F")
L-180,L-181,L-182,L-183,L-184,L-185.LC-180.LC-181,LC-l82 - FRONT BRAKE
13" x2-l/2" (TYPE "F")
L-190,L-19l,L-192,L-193,L-194.L-195,LF-190,LF-19l.LF-l92,LC-190,LC-19l,LC-192, L-200,L-20l,L-202.L-204.L-205,LC-200.LC-20l,LC-202 - FRONT BRAKE 15" x2-l/4" (TYPE "F") Bleeding the hydraulic brake system. . . . . . . . . . . . . . . Brake adjus trnent. . . . . . . . . . . . . . . . . . . . . . Brake component parts. . . . . . . . . . . . . . . . . . . . . . . . . . . Removal of brake shoes. . . . . . . . . . . . . . . . . . . . . . Removal of wheel cylinders . . . . . . . . . . . . . . . Replacement of brake shoes . . . . . . . . . . . . . . . . . . . . . . . . . . Replacement of wheel cylinders . . . . . . . . . . . . Service specifications . . . . . . . . . . . . . . . . . . . . . . . . . Wheel cylinder assembly . . . . . . . . . . . . . . . . . . . . Wheel cylinder disassembly . . . . . . . . . . . . . . . . . . . . . .
Page 5 4,5 2 3 3,4

4
4 5 4 4
SECTION "K"
L-160,L-16l,L-162,L-163,L-165,LC-160,LC-16l,LC-162 - REAR BRAKES
14-1/8" x 3" (TYPE "FR-2")
L-164,L-170,L-17l,L-172,L-173,L-175,LF-170,LF-17l,LF-172, REAR BRAKES 15" x 3" (TYPE "FR-2")
L-174,L-180,L-18l,L-182,L-183,L-185,LC -180,LC-18l,LC-182,LF-190
LF-19I,LF-192 - REAR BRAKES 15" x4" (TYPE "FR-2")
L2l0,L-2l1,LF-210,LF-2l1,LF-212,LF-220,LF-221,LF-222 FRONT BRAKES 16-1/2" x3-l/2" (TYPE "FR-2SII)
L-204,L-210,L-211 - REAR BRAKES 16-1/2 11 x7-1/8" (TYPE "FR-2SD") Bleeding the hydraulic brake system . . . . . . . . . . . . . . . . Brake adjus trnent . . . . . . . . . . . . . . . . . . . . . . . . Brake component parts . . . . . . . . . . . . . . . . . . . . . . . Removal of brake shoes . . . . . . . . . . . . . . . . . . . . . . . . . . Removal of shoe adjus Hng mechanism . . . . . . . . . . . . . . . . Removal of wheel cylinders . . . . . . . . . . . . . . . . . . . . . . . . . Replacement of shoe adjusting mechanism . . . . . . . . Replacement of brake shoes . . . . . . . . . . . . . . . . Replacement of wheel cy~inders . . . . . . . . . . . . . . . . . . . . . Service specifications . . . . . . . . . . . . . . . . . . . . . . . . Wheel cylinder as s embly; . . . . . . . . . . . . . . . Wheel cylinder disassembly . . . _.. , . . . . . . . . . . . . . .
11 10,11 2,4,6 8,9 8,9
9
10 10 10 12 9
SECTION ilL"
L-184,L-190,L-191,L"I92,L-193,L-195,LC-190,LC-191,LC-192,LF-2l 0, LF-211,LF-220,LF-221,LF-222 - REAR BRAKES 16" X 4" (TYPE "FR") L-194,L-200,L-201,L-202,L-205,LC-200,LC-20I,LC-202 - REAR BRAKES 16" x 5" (TYPE '! FR") 6 Bleeding the hydraulic brake system . . . . . . . . 5 Brake adjustment . . , " ... , . . . " . " " " " .. 2 Brake component parts . . . . . . . . . . . . . . . . . . 3 Removal of brake shoes . . . . . . . . . . . . . 4 Removal of shoe adjus ting mechanism . . . . . . . . . . . . . 3,4 Removal of wheel cylinders . . . . . . . . . . . . ',' . . . . (Continued)
& " " " " " " " " " " " "
PRINYEO IN U,..ITED STATES OF' AMERlCA
BRAKE SHOE ADJUSTMENTS AND SERVICING (CONTINUED) SECTION til" (Con'd)

R eplacemen t of shoe adjus ting mechanism . . . . . . . . . . . . Replacement of brake shoes . . . . . . . . . . . . . . . . . . . . . . . . . . Replacement of wheel cylinders . . . . . . . . . . . . . . . . . . . . . Service specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . Wheel cylinder assembly . . . . . . . . . . . . . . . . . . . . . Wheel cylinder disass embly . . . . . . . . . . . . . . . . . . . . . . . . . . . Page S 5 5
6
4 4
PARKING BRAKE ADJUSTMENTS SECTION "M"

LM-120,L-130,L-ISO,LM-1SO,L-160,LG-160,L-170,LF-170 Series Trucks. L-ISO,LG-lS0 Series Trucks. . . . . . . . . . . . . . . . . . . . L-190 and LF-190 Series Trucks; L-200, L-20l, L-202, L-204 Trucks. L-20S,L-210,L-211,L-2l2,LF-2l0,LF-211,LF-212,LF-220,LF-221 ,LF-222 . . . . . . Trucks. . . . 1 1 2 2
HYDRAULIC BRAKE SPECIFICATIONS

-
---
~-
--
~-
--
TRUCK MODEL Brake Type. . . . . . . .
L-IIO L-lli L-112 Hydraulic
L-120 L-121 L-122 Hydraulic
LM-120 LM-121 LM-122 Hydraulic
L-130 L-131 L-132 Hydraulic
LB-140 Hydraulic
L-150 Hydraulic
L-151 L-152 L-153 Hydraulic 12-ljax2xl/4 14-1/8x3x3/a
LM-150 LM-151 Hydraulic 12-=-1/8x2xl/4

14x2-1/4xl/4
-----~--
Brake Size (Standard):

Front . . . . . . 12xl-3/4x3/16 12xl-3/4x3/16 12xl-3/4x3/16 12xl-3/4x3/16 12xl-3/4x3/16 12:l/ax2xl/4 Rear. _ . . . . . . . . . . 12xl-3/4x3/16
---
12x2x3/16
12x2x3/16
14x2-1/4xl/4
14x2-1/4xl/4
14-I/ax3x3/8
Brake Size (Increased

Capacity): Front (Same as Standard) . Rear . . . . . . . . . _ .. Number of Shoes:
Front . . . . . . . . . . Rear . . . . . . . . . . Type of Anchor: Front . . . . . . . . . Rear . . . . . . . . . . . . . Wheel Cylinder Size (Standard) : Front . . . . . . . . . Rear ......' . . . ., . . . . . Wheel Cylinder Size (Increased Capaci ty);
Front (Same as Standard) Rear . . . . . . . . . . . . Number of Wheel Cylinders (Standard):
Front . . . . . . . . . . Rear . . . . . . . . . . Number of Wheel Cylinders (Increased Capacity): Front (Same as Standard) . Rear . . . . . . . . . . . Master Cylinder:
Size (Bore and Stroke) . . Type . . . . . . Hydrovac: Standard or OptionaL . . . Model No. (Bendix) . . . . Serie s . . . . . . . . . . Cylinder Diameter . . . . . Single or Tandem Piston .
..
.. . . .
2 2
----
. .. .
~
.. .
2 2
.........
..
.. ..
2 2 Single Single
c------
. .. .. ., . ........
~
----
. .. .. . .. .
~
12-1/sx2xl/4 14-1/8x3x3/a 2 2 Single

--
....... .. .' ......

..
2 2
12-1/ax2xl/4
14-1/8x3x3/8
2
2
[T1
t z
2
--
2 2 Single Single
-----
Single Single
Single Single
Single Single
,Single
----
Single
---
Single
Single
o -1 o :;;0
:;;0
-1
1
---
I
--
1 1-1/4
1 1-1/4
1 1-1/4
----
1 1-3/8
1 1-1/4
1-1/8
1-1/8
C
7'
en
..
.. .
.
. .
......
---
.. .
1 1
.......
1
---
. .. . . .. .........
1
.........
~
. ..
..
..
. . .
..
........
1 1
1-3/8
....... . ..... 1
I 1-3/8
n
[T1
<
I 1
1 1
--
......
. . "
.-
....
. . " ......
.
..
..
..
. - ...
.
..
.......... . .. . . .
1-1/axl-7/16 Barrel
- .... " .
1 2 1-1/axl-7/16 Barrel c:>.ptional 374000 .. C ..

----
........
1-1/8xl-7/16 Barrel
-,
" ........ . ........
1 2
1-l/axl.7/16
Barrel
z c
r
(/)~
~
1-1!8xl-7/16 Barrel
--
1-I/axl-7/16 Barrel
.
l-r/axl-7/16 Bar reI

~,:'"
1-1/4xl-7/16 Barrel Optional 374000 "C" 6-3/4" Single
ttl
. . ..
~
.
"
--------
. . ....
. .. .. . ..
........
..
.. .. . . . .. .
"
......
...... .
..
..
.
.. . .
........
.. .. . '" .. . ... " .. . .. .. . ..
...
"
........
........ . .. .
~
....... .........
. .
"
~~
'tJo><:
\I'\I'(/)
OQ
. . .
"
... .
'
....
(/)
.....
...
..
.......
"
"
....
.... " '.. . ......
6-3/4"
Single
"
..
OIl
. .......
" "
...
rogt"l
::r.
>-i
.... CIl:s::
- . - .. -.............
HYDRAULIC BRAKE SPECIFICATIONS - Continued

~-
IUCIltJ:I
--
TRUCK MODEL
LM-152
L-I60 L-161 L-162 L-163 L-165 Hydraulic
L-164
LC-160 LC-161 LC-162 Hydraulic
L-170
L-171 L-I72 L-173
L-175
---
L-174
I "d " OQ~> rot::;~ N .... 1:"l

n Icn
Brake Type . . . . . . . . . . . . . . . Brake Size (Standard): Front . . . . . . . . . . . . . . . . Rear . . . . . . . . . . . . . . . Brake Size (Increased Capacity): Front (Same as Standard) . . . . Rear . . . . . . . . . . . . . . Number of Shoes: Front . . . . . . . . . . . . . . Rear . . . . . . . . . . . . . . . . . Type of Anchor:
Front . . . . . . . . . . . . . . Rear . . . . . . . . . . . . . . . Wheel Cylinder Size (Standard): Front . . . . . . '. . . . . Rear . . . . . . . . . . . . . . . . . . Wheel Cylinder Size (Increased Capacity): Front (Same as Standard) . . . . Rear . . . . . . . . . . . . . . . . Number of Wheel Cylinders (Standard) : Front .. _ . . . . . . . . . . . . . . Rear . . . . . . . . . . . . . . . Number of Wheel Cylinders (Increased Capaci ty): Front (Same as Standard) . . . . Rear . . . . . . . . . . . . . . . . Master Cylinder: Size (Bore and Stroke) . . . . . . Type . . . . . . . . . . . _ . . . . Hydrovac: Standard or Optional . . . . ' Model No. (Bendix) . . . . . . . Series . . . . . . . . . . . . . . Cylinder Diameter . . . . . . . .
Hydraulic I Z-I/8x2xl/ 4 14-1/8x3x3/8
Hydraulic
Hydraulic
[y~
'aulic
8 cn !II~
::r.o<
l'1
IS:
12-1/8x2-1/4x5/16 12-1/8x2-1/4x5/16 12-1/8x2-1/4x5/16 12-1/8x2-1/4x5/16 12-1/8x2-1/4x5/16 14-1/8x3x3/8 15x3x3/8 14-1/8x3x3/8 15x3x3/8 15x4x3/8,
--
....... . .. .
2 2 Single Double
12-1/8x2-1/4x5/16 12-1/8x2-1/4x5/16 12-1/8x2-1/4x5/16 12-1/8x2-1/4x5/16 12-1/8x2-1/4x5/16 15x4x3/8 2 2 Double Double

---
15x4x3/8 2 2 Double Double 1-1/8 1-3/8
15x4x3/8 2 2 Double Double 1-1/8 1-3/8
15x4x3/8 2 2 Double Double 1-1/4 1-1/2
_15x5x3/8 2
2
Double
Double 1-1/4 1-1/2
[T1
~
C
:;;0 :;;0
-:I
---
1 1-3/8
1-1/8 1-3/8
7'
(fJ
......
1-1/8 1-3/8
1-1/8 1-3/8
1-1/8 1-3/8
1-1/4 1-1/2
---
1-1/4 1-1/2
. " ..
1 2
n
2
2
<
~
[T1
2 2
2 2
2 2
2 2
> Z
C
.........
2 2 1-1/4xl-7/16 Barrel
---
2 2 1-1/4xl-7/16 Barrel Standard 374000

ltC"
2 2 1-1/4xl-7/16 Barrel Standard 374000 .. C .. 6-3/4"
2
2 1-1/2xl-7/16 Barrel
Standard 375279
.. . .
> r
1-1/4xl-7/16 Barrel
~
Single Single (Guided) Single or Tandem Piston . . . Single Single Single (Guided) These hydrovacs contain a residual pressure check valve and must be used with a master cylinder that does not have a residual pressure check valve.
. . .... .. .. . .. . ... ., .....

~
.. . .
---
Standard 374000 'C

1
He"
9-1/2"
"C"
9-1/2"
6-3/4"
6-3/4"

LF-l70 LF-l71 LF-ln
-----
TRUCK MODEL
L-l80 L-18l L-182 L-l83 L-185 Hydraulic

---
L-184
LC-180 LC-18l LC-182 Hydraulic 13x2-1/4x5/16 l5x4x3/8

------
L-190 L-19l L-l92 L-193 L-l95

L-194

----
Brake Type . . . . . . . . . . . . .
Hydraulic
Hydraulic l3x2-l/4x5/16 l6x4x3/8 l3x2-f/4x5/l6 l6x5x3/8 2 2 Double Double 1-1/8 1-1/2
Hydraulic 15x2-1/4x5/l6 16x4x3/8 l5x2-1/4x5/l6 16x5x3/8 2 2 Double Double

-----
Hydraulic
l5x2-l/4x5/16 l6x5x3/8
l5x2-l/4x5/l6 l6x6x3/8 2
2
Double Double
1-1/4
1-3/4
Brake Size (Standard): Front . . . . . . . . . . . . . . . . . 12-1/8x2-l/4x5/16 Rear . . . . . . . . . . . . . . . . l5x3x3/8
13x2-1/4x5/16 l5x4x3/8 13x2-l/4x5/16 15x5x3/8 2 2 Double Double 1-1/8

----
Brake Size (Increased Capacity): Front (Same as Standard) . . . . l2-l/8x2-1/4x5/l6 Rear . . . . . . . . . . . . . . . . Number of Shoes:
Front . . . . . 15x4x3/8 2 2 Double Double 1-1/4 1-3/8
13x2-l/4x5/l6 l5x5x3/S 2 2 Double Double 1-1/8 1-3/4
t z
[TJ
.........
$:
Rear . . . . . . . . . . . . . . . Type of Anchor: Front . . . . . . . . . . . . . . . . Rear . . . . . . . . . . . . . . . . Wheel Cylinder Size (Standard): Front . . . . . . . . , . . . . . Rear . . . . . " . . . . . . . . . . 'Wheel Cylinder Size (Increased Capacity): Front (Same as Standard) . . . Rear . . . . . . . . . . . . . . . . Number of Wheel Cylinders (Standard): Front . . . . . . . . . . . . . . . . Rear . . . . . . . . . . . . . Number of Wheel Cylinders (Increased Capacity): Front (Same as Standard) . . . Rear . . . . . . . . . . . . . . . . . . Master Cylinder: Size (Bore and Stroke) . . . . '. Type . . . . . . . . . . . . . . . . Hydrovac: Standard
Or
----
~
C
1-1/4 1-3/4
;:j
()
1-1/2
~
Ul
1-1/4 1-3/8
1-1/8 1-1/2
1-1/8 1-1/2
I-lis 1-1/2
1-1/4
-----
1-1/4 1-3/4
1-3/4
<
() [TJ
2 2
2 2
2 2
!
2 2
~-.
2 2
2
2
2 2 1-3/4xl-7/16 Barrel
---
2 2 1-1/2xl-7/16 Barrel Standard

--------
2 2 1-1/2xl-7/16 Barrel Standard 375279 "C" 9-1/2"
2 2 1-1/2xl-7/l6 Barrel Standard 375279 "C"

-----
2 2 1-3/4xl-7/16 Barrel Standard 375278 "C" 9-1/2"
2
2
1 .3!"4xl-7/16 Barrel
Standard 375278
l~C'
z c r
~>
b1 l:tI
$:
-_.---------
Optional . . . . . .
Standard 375278 .. C ..
Model No. (Bendix) . . . . . . . Series. . . . . . . . . . . . . Cylinder Diameter. . . . . . .
*
------
---
375279
------
*'
~,
"C"
-----
;:!!(Il
~ ~ oM ",.
9-1/2"
9-1/2"
9-1/2' ,
9-1/2"
Single (Guided) Single (Guided) Single (Guided) Single (Guided) Single (Guided) Single (Guided) Single or Tandem Piston ._ . _"__ These hydrovacs contain a residual pressure check valve and .must be used with a master cylinder that does not have a residual pressure check valve.
,,0"':: PlPI(Il OQ ::r. I-i
CDM
""tilts:

~~
OQ~> (\) I=::;~

II~.
"OC/ltJj II' 't:l !:D
TRUCK MODEL
-
LF-190 LF-191 LF-192 Hydraulic ISx2-1/4xS/16 ISx4x3/S ISx2-1/4xS/16 15x5x3/8

2
LC-190 LC-191 LC-I92 Hydraulic

-
L-200 L-201 L-202 L-20S

-
L-204
LC-200 LC-201 LC-202 Hydraulic 12x.2-1/4xS/16 l6xSx3/8 15x2-1/4x5/16 16x6x:?/S 2 2 Double

.~~
t<:I
L-201 L-211 Hydraulic 16-1/2x3-1/2xS/S 16-1/2x7-1/8xS/S
II'C/l
0:..::
(Il
::s .,
t<:I ~
OC/l
Brake Type . . . . . . . . . . . . .
Brake Size (Standard): Front . . . . . . . . . . . . Rear . . . . . . . . . . . . . . . . . . . Brake Size (Increased Capacity): Front (Same as Standard) . . Rear . . . . . . . . . . . . . Number of Shoes: Front . . . . . . . . . . . . . . . Rear . . . . . . . . . . . . . . . . .
Hydraulic lSx2-1j4xS/16 16xSx3/8 lSx2-1/4xS/16 16x6x3/8 2 2 Double Double

~-
Hydraulic ISx2-1/4xS/16 16-1/2x7-1/8xS/S

10 .. .. ,.,
lSx2-1/4xS/16 16x4x3/8 lSx2-1/4xS/16 16x5x3/8 2 2

-
...
2
- "' .....
.
"
.....
2 4
[11
t z
2
-
2 Double Double 1-1/4 1-S/8

f--
3:
Type of Anchor: Front . . . . . . . . . . . . Rear . . . . . . . . . . . . . . . Wheel Cylinder Size (Standard): Front . . . . . . . . . . . _ . . . Rear . . . . . . . . . . . . . . . . . Wheel Cylinder Size (Increased Capacity): Front (Same as Standard) . . . Rear . . . . . . . . . . . . . . _ Number of Wheel Cylinders (Standard) : Front. . . . . . . . . . . . . . . . . . Rear . . . . . . . . . . . . . . Number of Wheel Cylinders (Increased Capacity): Front (Same as Standard) . . Rear . . . . . . . . . . . . . . . . . )I/laster Cylinder: Size (Bore and Stroke) . . . Type . . . . . . . . . . . . .
Hydrovac:
Standard or Optional . . . . . .
Model No. (Bendix) . . . . . .
Double Double
-
Double Double 1-1/4 1-3/4
Double Double
-
~ o
~
--
Double 1-1/4 1-3/4
-l
1-1/2 1,5/8
1-1/4 1-1/2
1-1/4 1-3/4
(')
7\
1-1/4 1-1/2 1-1/4 1-3/4 1-1/4 1-3/4
. .....
2 2 Siamese Twin-type
..
. .. ..
1-1/4 1-3/4
(J)
.... II' ...
[11
.......
2
2 Siamese Twin-type
2 2
2 2
2 2
[11
< o
3:
2 2 1-3/4xl-7/16 Barrel
-

"C't
"
2 1-3/4x2-1/2 Barrel Standard 374229

\lC"
........
. .
. .
2 2 1-3/4xl-7/16 Barrel Standard 375278 "C" 9- 1/2" Single (Guided)
..... . ..
'"
z c
r
1-3/4x2-1/2 Barrel Standard 374230 "C" 9-1/2" Tandem
1-3/4x2-1/2 Barrel Standard 374230

"Ct'
Standard 375278
~(C~'
Series . . . . . . . . . . . .
~linder
Diameter . . . . . . .
Single or Tandem Piston . . . .
9-1/2" Tandem
9-1/2" Single (Guided)
9-1/2" Single (Guided)
9-1/2" Tandem
* These
hydrovacs contain a residual pressure check valve and must be used with a master cylinder that does not have a residual pressure check valve.
TRUCK MODEL Brake Type . . . . . . . . . . . . .
LF-210 LF-211 LF-212 Hydraulic
L-220 L-225
LF-160 LF-221 LF-222 Hydraulic 16-1/Zx3-1/Zxs/s 16x4x3/8
L-230 L-231
LF-230 LF-23l
.......
..
.....
......
. .
. .
Brake Size (Standard): Front . . . . . . . . . . . . . . 16-1/2x3-1/Zxs/s Rear . . . . . . . . . . . . . Brake Size (Increased Capacity): Front (Same as Standard) . . . Rear . . . . . . . . . . . . . . Number of Shoes: Front . . . . . . . . . . . . . Rear . . . . . . . . . . . . . . . . . Type of Anchor: Front . . . . . . . . . . . . . . . Rear . . . . . . . . . . . . . Wheel Cylinder Size (Standard): Front . . . . . . . . . . . . . Rear . . . . . . . . . . . . . . . Wheel Cylinder Size (Increased Capacity): Front (Same as Standard) . . . Rear . . . . . . . . . . . . . . . . . Number of Wheel Cylinders (Standard) : Front . . . . . . . . . . . . . . . . Rear . . . . . . . . . . . . . . . . . . Number of Wheel Cylinders (Increased Capacity): Front (Same as Standard) . . . .
-----
. . ..
.
.
16x4x3/8
....
"
.
.
"
---
...... . ... .. ........
. .. . ........
..
. .
. ....
. . .
.. .. ..
...........
..........
2 2 Double Double
..
. ..
----
.
"
.. .
--------
. .. .
........
........
-------
2. 2 Double Double
........
-------
.........
...
........
["l1
t z
.
<-
......
.........
.
~
........
"
.......
... - .
..
$: o ...;
. .
....
.,
..
..
-------
......
.
. .. .
o ;::0
I-liz
1-3/4
......
I-liz 1-3/4
-.
...
...;
.. ........
..........
.
.. ........
........
.......
()
~
A
U>
.. - ...
. .. . ..
..
. ..
"
.
-----
..
......
. .
..
........
. ..
....
..
. ..
. . ..
..
["l1
........
........
;::0
2 2
........
----~
........
.. .. to ...
< n
["l1
. .
2
---
" .....
,.
$:
----
........
.. .. . .
..........
.
.
------
.....
"
........
<0
......
---~
Rear . . . . . . . . . . . . . . . .
---
- ..... ..
---
.. ........
1-3/4xZ-I/Z
.
..
...
..
----~---
........
.
"
z c::
:r>
Master Cylinder: Size (Bore and Stroke) . . . . . . Type . . . . . . . . . . . . . . . . . Hydrovac: Standard or Optional . . . . . . Model No. {Bendix} ., . . . . . . Series . . . . . . .
.
~
:r>
r
C/l~
I::;
tl1
1-3/4x2-1/2 Barrel Standard

-----
.......
Barrel
..
. .. . .
*
..
-------
....... ... " .

"
.....
..
~
. .
.
"
. ..
Standard 374Z30
'C'l
374230
~IC"
....
., .,
. ... . . . ..
II> "
,.
,.
~
.. ..
"
...
~
'g~
,.
"
..
-------
Cylinder Diameter . . . . . . . Single or Tanden Piston . . . . .
9-1/2"
-----
...... . . ., .
"
----
9-1/Z" Tandem
Tandem
.. .
~
..
. . ..
~
.. .
~
...... .. . . ......
ntri
.... C/l
III III C/l

OQ
'"cJn><
lI>tri
::r."
These hydrovacs contain a residual pressure check valve and must be used with a master cylinder that does not have a residual pressure check valve.
V\D>iS':
AIR BRAKE SPECIFICATIONS

L-IB4 L-190 L-191 L-l92 L-19S Special l6xl-l/4xS/16 16-l/lx6x3/4 Back. Plate E 6-3/16 Axle Pad C
-
1jtlltJj
III 'tI ::tl OQ~>
TRUCK MODEL
L-IBO L-IBl L-IBl L-IBS Special
LC-IBO LC-IBI LC-IBl
LF-190 LF-191 LF-192
LC-190 LC-191 LC-l92
L-194 L-lOO L-201 L-202 L-20S Special 16xl-l/4xS/16 16-1/2x6x3/4 Back. Plate E 6-3/16 Axle Pad B 9-3/16 S 7
~
LC-lOO LC-201 LC-202
O'h' M
(\)I::;~
::r.-< o til
Ul
III til i:I ,...:j
Standard or Special. .
. . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . .
-
. . . . . . . . . . . . . .
-
. . . . . . . . . . . . . . . . . . . . . . . . . ... . . . . . . . . . . . .
.... .. .. .. . . . . ... . .. .... .. . . . . .. .
Brake Size: Front . . . . . . . . . . l6xl-l/4xS/16 Rear . . . . . . . " Brake Chamber-Front: Location. . . . . . . . Type . . . . . . . . . Size.. . . . . . . . . Brake Chamber-Rear: Location. . . . . . . Type . . . . . . . . Size.... . . . . . . Slack Adjuster Length: Front . . . . . . . Rear . . . Brake Valve: Model. . . . . . . Control. . . . . . . . . Air Reservoir: Number Used. . . . . Length and Diameter. Air Compressor: Type (Westinghouse). Capacity in Cu. Ft . Cooling. . . . . . Mounting. . . Drive.. . . . . . 16xS-l/lxl/l Back. Plate E 6-3/16 Axle Pad C B-l/16 3-3/B 6 D-l Foot Pedal 1 4l-1/lxB
r: c z
[TJ
~ o ~
C
3:
--1
~ ()
9-3/16 4 6 D-l Foot Pedal 1 4l-l/2xB
. . .. . . . . . . . . . . . .
A
tf)
[TJ
n
[TJ
. . . . . . . . . . . . . .
D-l Foot Pedal 1 41-1/lx8
z r
c
3:
----
l-Cyl. 7-1/4 Water
. . . . ... , _
l-Cyl. 7-1/4 Water
. . . . . , , ...... .
.. , . . . . . , _ ~ _~ ._~.~
2-Cyl. 7-1/4 Water Engine __ 13~lt
, . .. , .
Engine , . Engine .J?e!:f; ____ ._--,,- ._~._,---.~Belt __ __
_._'....:.._._.'---_
AIR BRAKE SPECIFICATIONS - Continued

---
TRUCK MODEL
L-204
L-2l0 L-2l1
LF-210 LF-211 LF-ZIZ
L-220 L-2Z5
LF-220 LF-Z21 LF-222

.. .. .. .
--------
L-230 L-Z31
---------
LF-230 LF-Z31
Standard or Special. . . . Brake Size: Front . .

~
Special 16xZ-I/4x5/16
------
Special l7-1/4x3x3/a l6-l/Zx7x3/4 Back. Plate A 6-15/16 Axle Pad

G
..
..
..
<II
..
..
>
..
..
.
..
..
.. ..
..
..
"
to
..
..
.......
.. .
.. ..
.
(j.
..
..
. . .. ..
.. . ..
..
.. ., ..
.. dO ..
..
..
.. .. . .. ..
.
.. .. .. ..
.
..
Rear . . . . . . 16-I/Zx7x3/4 Brake Chalnber- Front: Location . . . . . . . . Type . . . . . . . . . Size . . . . . . . . . . Brake Chalnber-Rear: Location . . . . . . . . Type . . . . . . . . . . Size . . . . . . . . . . . . Slack Adjuster Length: Front . . . . . . . . Rear . . .- . . Brake Valve: Model. . . . . . . . . Control. . . . . . . Air Reservoir: NUlnber Used . Length and Dialneter . . Air COlnfressor: Type Westinghouse) . Capacity Cu. Ft . . . . Cooling . . . . . . . . . Mounting. . . . . Drive . . . . . . . . . . Back. Plate E 6-3/16 Axle Pad
G
. ..
.. . .
.. .. . . ..
r: c Z
. .. . . .. . .. .. . .
. . . .. . . . . .. ..
. .. . .. .. . .. .. . .
.. ..
.. ..
------
..
.
..
fT1
..
. ..
'"
. . .. . .
.. .. GI ..
.
..
.. "" .. .. ..
.. " <0
..
..
..
>
..
..
..
. .. . .. .
It .. .. .. ..
..
..
. .
o -l o :A)
:A)
.. .. . . .
. .. .
.. .
,.
..
.. .. ..
------
..
.. .
. ..
..
..
..
1:1
..
..
-l
..
..
..
a
.
..
.. .. .. .. ..
.. a .. ..
9-7/a 5 6-l/Z D-I Foot Pedal 1 4l-l/Zxa Z-Cyl. 7-1/4 Water Engine Belt
------
9-7/a 5 6-1/2 D-I Foot Pedal

I
. . ..
.. .... . .. .. ..
------
.. ..
......
. . .. .
.. .
"
~
(J)
.......
00<
. .. ..
.
~
.. ..
. . ..
"'
.. . . . ..
.. .. .
. .. . .. ..
. . .. . .. .. . .. . .
.. It .. .. ..
. ..
..
..
.
.
..
..
.
Ii)
.. ..
..
.. .. .
........
------
fT1
:A)
n fT1
~
<
. .. ..
------
.
"
..
..
..
..
'"
..
......
.
..
----~
. ..
..
..
..
f)
..
. .. .. ..
r------------
.. .. .. .. ..
.. ..
.. ..
..
z
c
..
..
'"
.. ..
..
..
.. " .
4l-l/2xa Z-Cyl. 7-1/4 Water Engine Belt
..
.. ..
....
,. '"
'" '"
..
.. ..
..
'"
..
.. ..
..
..
..
..
..
..
..
..
<;I
..
. ..
. .. . .. . .
r
tJj
------
. .
.. .
'" ..
'" <
..
'"
.
'"
. '" . '" '" . '" '" '" . .. . . . . . '" . .

'" '" - -..- - -"- '" '
----~
. . . .. .. . . . .. .
'"
.. '" '" 0
'"
....
a a ,.
OJ
....
l:Q
'"
'"
. . . .. .. . .
~
... . . . ..
'"
OJ
OJ
'"
..
]~
t-'
1Zl
. . . '"
..
..
.. '"
. ..
..
. . . ..
IUIUIZl (lQ p: ~ (1) 0 tx:l
'1:l n O-<
-.Jg~
~1Zl
BRAKES HYDRAULIC Section A Page 1
HYDRAULIC BRAKES
HYDRAULIC BRAKE SYSTEM

The hydraulic system used to actuate the brake mechanism consists of a compensating type master cylinder in which the hydraulic pressure is originated; individual wheel cylinders, in which the hydraulic pressure is applied, which serve to actuate the brake shoes against the br ake drum of each wheel; and the "Line" con sisting of steel tubing, flexible hose, brackets and unions, interconnecting the master cylinder and wheel cylinders. The master cylinder and wheel cylinders are fitted with pistons, all of which are provided with cup packings, which act as a seal to maintain pressure and prevent loss of brake fluid. Depressing the brake pedal moves the piston within the master cylinder, thus displacing the brake fluid from the master cylinder through its outlet orifices, tubing and flexible hose con nections into the wheel cylinders. The brake fluid, being noncompressible, enters each of the wheel cylinders, causing the cylinder pistons to move outward and actuate the brake shoes. As pressure on the pedal is increased, greater hydraulic pressure is built up within the wheel cylinders, and consequently greater force is exerted against the shoes. When the pressure on the pedal is released. the brake shoe retracting springs return the brake shoes to their normal or released position. The return movement of the brake shoes, in turn, causes movement of the wheel cylinder pistons toward their released position. thus forcing the fluid back thru the tubing into the master cylinder. compensating port (C) and the pressure stroke commences. Actual pressure is not built up until the fluid displaced has caused all shoes to go into con tact with their drums. Additional pressure on the pedal produces hydraulic pressure within the brake system. Removal of operator's foot from the brake pedal after each brake application permits the brake pedal and push rod (A) to return independently to their off-position. The return of piston (B) and cup (D) is accom plished by the piston return spring (I). The piston for this type of unit is designed to carry a primary cup (D) and a secondary cup (E). The construction of the piston is such that reserve fluid from the tank passes through vent (R) in a recessed area. Thus we have fluid on both sides of the primary cup. The secondary cup (E) is merely a seal to prevent loss of reserve fluid into boot (G). The combination type master cylinder is also known as a compensating type. Its primary compensating function is to maintain a constant volume of fluid in the system at all times, re gardless of expansion (heat) or contraction (cold). The secondary compensating function is the replacement of additional fluid into the system to counterbalance any loss due to gravity seepage. The return to off-position of piston (B) and cup (D) is much faster in displaced volume than the return of the fluid through fitting (J) into the master cylinder. A momentary vacuum is created in the cylinder barrel and additional fluid is drawn into the system through the drilled holes in piston (B) and past the lip of cup (D). The operating fluid returns more slowly from the wheel cylinders and lines back into the master cylinder barrel. Any excess is by-passed by port (C) into the reservoir. Thus we have a cylinder full of fluid for the next brake application.
HydrauliC
F~uid
Always use genuine "Lockheed" or other high grade automotive type brake fluid. The use of other than genuine "Lockheed" or any high grade automotive type brake fluid or the introduction of mineral base oil into the system will cause rubber parts to swell and become inoperative.
Combination Type Master Cylinder (Fig. 1)

The combination type master cylinder consists of barrel and tank casting, double check valve (L), piston cup return spring (I), piston cup (D), piston (B), piston stop (p). boot (G) and connecting
link (A).
L
IHllli!l"ot--J
The fluid reservoir or supply tank is cast in tegral over the master cylinder barrel. A com bination filler and breather plug (N) permits atmospheric pressure on the reserve fluid at all times. Depression of the pedal causes piston (B) and cup (D) to move forward in the cylinder barrel. A very small forward movement of cup (D) closes
PRINTED IN uNITED STA.TES OF AMRtCA
A G Fig. I
A22934
Typical Combination Type Master Cyl
inder.

Boot
Cup
Check Valve
A double check valve is used in all master cylinders of the compensating type. It is held in the closed end of the master cylinder barrel by the piston cup return spring.
The valve performs two functions: It acts as~ a seal to prevent fluid or air being drawn into the system through the bleeder screw during the bleeding operation. Fluid passed through the valve on the pressure stroke can return into the master cylinder barrel only by raising the entire valve from its seat. The valve is held in place by the cup return spring. When the pressure on the returning fluid drops below 6 to 8 pounds, the spring closes the valve and the system is under a slight pressure. This pressure will not cause the shoes to drag. It is used to assure a positive seal at the wheel cylin der cup packings. The valve does not control brake pedal move ment. Do not try to remedy this complaint by changing the valve. NOTE: On vehicles equipped with certain models of Hydrovacs the check valve is located in the Hydrovac slave cylinder tube; and where this is the case, no check valve is used in the master cylinder. (See Hydrovac Specifications.)
Piston spring
141---
Bleeder valve
A-22728
Fig. 3 type)
Typical Wheel Cylinder (Oouble-piston
Repairs to Master and Wheel Cylinders

It is possible to rehone the majority of cyl
inders and place them in good working condition; however, this requires the use of up-to-date honing equipment and plug gauges. A cylinder hone kit is available under number SE-1679,and a set of plug gauges under number SE-IOOO.
If this equipment is not available, we recom mend that the unit be taken to the nearest Wagner Service Branch or Authorized Service Station for repairing,
Wheel Cylinders (Fig. 2 and 3)

Two types of wheel cylinders are used in the hydraulic brake system. Different combinations of these two types of cylinders are used on different model trucks. Fig. 2 illustrates a single piston wheel cylinder, and Fig. 3 illustrates a double piston wheel cylinder. The wheel cylinder assembly is the unit that changes the applied hydraulic pressure into mechanical force to actuate the brake shoes.
Cylinders and parts must not be washed in gasoline, kerosene or oil. Use high-grade denatured alcohol.
Care
Keep all lubricant and brake fluid away from brake linings. Inspect master cylinder at the time of making brake adjustments -- for correct fluid level. Fluid should be within 3/8" from bottom of filler neck. Do not fill supply reservoir to top of filler neck. Caution: When removing supply reser voir filler cap, extreme care must be used to prevent dirt or moisture from entering master cylinder.
Piston spring
Piston
Brake pedal Adjustment

When brake control system is in release position, foot brake pedal should have 1/4" free travel (Fig. 4) before the pressure stroke starts. This free travel is required to prevent blocking of compensating port in master cylinder. Brakes will drag if compensating port becomes blocked due to pressure building up in the system. Shorten pedal push-rod to allow piston to uncover compensating port, allowing fluid to escape into tank.
A-22743
Fig.2 ty pe).
Typical Wheel Cylinder (Single-piston
Fig. q - Brake Pedal Free Travel.
Bleeding The Lines (Also see Hydrovac Section)

Any air inside the hydraulic system must be removed. Whenever a line has been discon nected at master cylinder, the entire system must be bled at all wheels until all air is com.pletely expelled. When a line has been disconnected at any wheel cylinder, this cylinder together with the cylinder on the opposite wheel must be bled. Air in the system will cause a springy, rubbery action of the brake pedal. Should a sufficient quantity be introduced into the system, the brake pedal will go to toe board under norm.al pressure. Fill master cylinder supply reservoir with genuine Lockheed or any high grade automotive type brake fluid and see that it is kept at least half full during entire bleeding operation. Use pressure-type brake bleeder where avail able. Attach bleeder tube to bleeder valve by pushing tube over the end of bleeder valve. Allow tube to hang in a clean container, such as a pint glass jar. Unscrew bleeder valve 3/4 turn and depress brake pedal by hand, using half strokes, allowing pedal to return slowly. Pumping brake pedal forces fluid out into glass jar, and carries with it any air which might be present in the system. Watch flow of fluid from tube, the end of which should be kept below sur face of fluid in pint bottle, and when all air bubbles cease to appear or when streamis a solid fluid mass, close bleeder valve. (See Fig. 5.) Fluid withdrawn in bleeding operation should not be used again, unless absolutely certain that it does not contain iITlpurities. Fluid of
PR!N'r~O
Fig, 5
which the cleanliness is questionable should never be used. Fluid should be replenished in supply reservoir after each cylinder is bled. Should supply reservoir be drained during bleed ing operation, air will enter the system and re bleeding will then be necessary.
Maintenance Hints
1. PEDAL GOES TO FLOOR BOARD:
Normal wear of lining. Brake shoes not properly adjusted. Leak in system. Air in system. (e) Pedal improperly set. (f) No fluid in supply reservoir.
(a) (b) (c) (d)
(a) When brake linings become worn it is necessary to set the shoes 'into closer relation to bra.ke drums. This condition is usually accompanied by the remark that it is necessary to pump the pedal several times before a brake is obtained. Shoes should be set in accordance with instructions on ADJUSTMENTS FOR WEAR. Do not disturb anchor pins when ITlaking this adjustment. Adjustment must be made while drums are cool.
IN UNltEO STATES OF' AMERICA

gradually build up and brakes drag. Shorten pedal push rod to allow piston to uncover compensating port, allowing fluid to return to tank.
(b) In cases where the anchor pins have been disturbed and the relation of the arc of the shoes to drums changed, lining will wear rapidly and the braking ef ficiency of that particular wheel will be reduced. To overcome this condition, follow instructions as outlined in MAJOR ADJUSTMENTS, brake shoe adjustment sections. (c) A leak in the system will allow the pedal, under pressure, to go to toe board gradually. If no leaks are found at wheels or joints, remove master cylinder and check bore of barrel for scores or scratches. (d) Air in the system will cause a springy, rubbery action of the pedal. Should a sufficient quantity be introduced' into the system, the pedal will go to toe board under normal pressure. System should be bled, (e) Brake pedals should be set to give the correct amount of free movement before the pressure stroke starts. Excessive free movement reduces the active travel of the master cylinder piston, which in turn determines the amount of working fluid to be expelled from the master cylinder into the lines or system. (f) The fluid level in the supply reservoir should be checked at regular intervals. Should the reservoir become empty, air will be introduced into the system, necessitating bleeding. Z. ALL BRAKES DRAG:
3. ONE WHEEL DRAGS:
(a) Weak brake shoe return spring. (b) Brake shoe set too close to drum. (c) Cups distorted. (d) Loose wheel bearings. Remedy (a) Springs sometimes lose their con tracting power and take a set. Replace spring. (b) Readjust shoes to proper clearance. Do not change anchor pin setting unless necessary. (c) If in repairing wheel cylinders, kero sene, gasoline and other fluids are used as a cleaner, instead of alcohol, the cups will swell and distort. The return action of the shoes will be retarded and the brake drum will heat. Replace cups and wash unit in alcohol and dip all parts in fluid before reassembling. (d) Tighten bearings.
4. TRUCK PULLS TO ONE SIDE: (a) Mineral oil in system. (b) Pedal improperly set. (a) Grease-soaked lining. (b) Shoes improperly set. (a) The introduction of mineral oil, such as engine oil, kerosene, or any fluid with a mj,neral base, into the system will cause the cups to swell and distort, making it necessary to replace all cups and flush system. (b) Directly ahead of the master cylinder piston cup (when in normal release position) is a relief port. It is im perative that this port be open when the brakes are released. Brake pedal should be set to give the proper free movement before pressure stroke begins. Should this port be blocked by piston cup not returning to its proper release position, the pressure in the system will (c) Backing plates loose on axle. (d) Front spring U-bolts loose. (e) Different makes of lining. (f) Tires not properly inflated.
(a) Replace with new lining of same make'. Grease-soaked linings cannot be sal vaged by washing or cleaning. (b) Refer to MAJOR ADJUST1YlENTS, brake shoe adjustment sections.

(c) Loose backing plates perlTIit the brake asselTIbly to shift on the locating bolts. This shifting changes the predeterlTIined centers and causes unequal efficiency. Tighten backing plate and readjust shoes with feeler gauge. (d) Loose spring U-bolts perlTIit the axle to shift on the springs and run out of line. This is noticed especially when a high braking torque is developed. Tighten U-bolts at their proper location on spring. (e) Different ITIakes of linings have different braking efficiency. Two different lTIakes. one with high efficiency and one with low efficiency, would cause truck to pull to one side. (f) All tires should be properly inflated. 7.
LIGHT PRESSURE ON PEDAL, SEVERE BRAKES: Cause (a) Brake shoes not properly adjusted. (b) Loose backing plate on axles. (c) Grease-soaked lining.
RelTIedy
(a) Consult relTIedy (b) under No.4. (b) Consult relTIedy (c) under No.4. (c) Consult relTIedy (a) under No.4.
5. SPRINGY, SPONGY PEDAL: Cause (a) Brakes shoes not properly adjusted. (b) Air in systelTI.
RelTIedy
(a) Consult relTIedy (b) under No. 1. (b) Consult relTIedy (d) under No.1.
6. EXCESSIVE PRESSURE ON PEDAL, POOR STOP: Cause (a) Brake shoes not properly adjusted. (b) lITIpr oper lining. (c) Oil in lining. (d) Lining lTIaking partial contact.
RelTIedy
(a) Consult relTIedy (b) under No. 1. (b) Specified linings have been developed to give satisfactory service and no changes should be lTIade in the field to other lTIakes of linings. (c) Replace shoes. (d) RelTIove high spots.
PRINTEO IN
UNIT~C
STATI;S OF AMERICA
BRAKES HYDROVAC POWER Section B Page 1
HYDROVAC POWER BRAKE SYSTEM
Atmo.phere control . line Bleeder valve.
'Trailer brake conoectioo plug
'Contr~1 vah'e--_ _ _ _ _ _....:
-----_3
End plate
Atmosphere i81e1 _ _ _---.,;...

From Bir deaner
vac.uum lource
Fig. I - Exterior View of Third Series ("C" Series) Single 6-3fij" Diameter Piston Hydrovac ~o. ~7qOOO (Fig. 2 illustrates the Interior Details of the Above Unit.)
Colllrol valve piston
. Diaphragm retlD'D spring
Bleeder valve
Outlet to wheel .cylind;rs .
VaC1l1llllilktoD
Lubrication plug
Cylinder sheD
A-23201
Fig. 2 - Sectional View of Third Series Diameter Piston Hydrovac No. 37QOOO.
PR1NTO IN UNITED STATES OF' AMfUCA
("C R Series)
Single 6-3/qn
Atmosphere control line Trailer brake connection plug

""
~.'UllU"l
sheD
Piston guide tube Atmosphere inlet _ _ _ _ _ _ _ _.....}.;;:: from air cleaner
----F.".1 plate
Bleeder u.l.,.---"\. Outlet to wheel __--~. cylinders bolt Inlet from master
A-22B1B
Fig. 3 - Exterior View of Third Series ("C" Series) Single Diameter Guided Piston Hydrovacs H~'s. 375278 and 375279.
9-1/2"
Clamp bolt
Push rod---------rJI Vacuum

piston-----:+:-l:~!!
plug--~~U
Outlet to wheel cylinders
Lubrication
Cylinder shell-----.../ Vacuum inlet from vacuum source (Inlet drawn out of position)
A-22737
Fig. ~ - Sectional View of Third Series ("C" Series) Single 9-1/2"

Diameter Guided Piston Hydrovacs No's, 375278 and 375279.

Atmosphere inlet to fast application valve from enaine air deaner
valve
wei .~_'JIIII"'l:'lll!'l"" from engine -"'~air clellDer
Atmosphere
Lubrication
pilIP
Di~meter
Fig. 5 - Exterior View of Third Series ("C" Series) Cyl inder Hydrovacs No's. 374229 and 374230.
Tandem
9-1/2 u
BLEEDER
VALVE-"
Fig, 6 - Sectional View of Third Series ("C" Series) Diameter Cyl inder Hydrovacs No's. 374229 and 374230.
Tandem
9-1/2"

must be allowed to snap back MQUICKLY" to be released position. This rapid return of the pedal and master cylinder piston allows the master cylinder barrel to receive brake fluid from the master cylinder reservoir on the return stroke and not just draw fluid back out of the lines when the pedal is released. Continue bleeding until all of the air is expelled, close bleeder valve. Repeat bleeding operation at bleeder valve No.2, making sure the master cylinder fluid reservoir is kept full of brake fluid. 4. Bleed the wheel brake cylinders in any con venient order. NOTE: Fluid withdrawn in the bleeding operation should not be used again.
HYDROVAC POWER BRAKE SYSTEM

(Bendix Hydrovacs Third Series IICI!
Nos. 374000, 375278, 375279,
374229 and 374230)
Hydrovac Power Brake Units
(Figs. 1, 2, 3, 4, 5, 6)
The hydrovac is installed on vehicles having the conventional hydraulic brake system to make available to the operator a greater pressure on the hydraulic brake system than could be exerted by foot pressure alone.
Description
The hydrovac is a hydraulic-vacuum power braking unit which is connected to the truck or bus braking system by a hydraulic line from the vehicle brake master cylinder to the hydro vac and a hydraulic line from the hydrovac to the wheel cylinders of the vehicle brake system. Vacuum for operation of the hydrovac is obtained from the engine intake manifold. The hydrovac is a self-contained unit having no external rods or levers exposed to dirt or moisture to rust and corrode. Figs. 1 and 2 illustrate the single piston 6-3/4" diameter hydrovac. Figs. 3 and 4 illustrate the single guided piston 9-1/2" diameter hydrovac. Figs. 5 and 6 illustrate the tandem piston 9-1/2" diameter hydrovac.
Lubrication
It has been definitely established that lubrication is highly important in hydrovac maintenance and that neglectofthis service adverselyafects performance.
Hydrovacs shOUld be lubricated as follows:

1. Single piston 6-3/4 11 diameter hydrovacs should be lubricated once a year (prefer ably before cold weather) or every 20,000 miles, whichever occurs first.
Bleeding Instructions
Bleed the hydrovac and wheel cylinders with the engine stopped, bleeding the hydrovac first at the two bleeder valves (Figs. 2, 4 and 6) in the control valve and in the slave cylinder in the following manner: 1. Attach bleeder tube to bleeder valve No.1 by pushing the end of tube over the bleeder valve. 2. Insert the end of bleeder tube in a con tainer containing a small amount of brake fluid.
2. Single piston 9-1/2 I! diameter hydrovacs should be lubricated every six (6) months or every 10,000 miles, whichever occurs first. One of these lubrication periods should occur just prior to the start of cold weather.
3. The tandem piston hydrovac s should be lu bricated once a year (preferably before cold weather) or every 20,000 miles, which ever occurs first.
The lubrication service should be performed with the hydrovac mounted on the vehicle, with the engine stopped, and brakes released. Single piston hydrovacs have one pipe plug in the cylinder shell (Figures 2 and 4), remove pipe plug and fill cylinder with vacuum cylinder oil to the level of the bottom of the hole. Replace pipe plug. Tandem piston hydrovacs have two pipe plugs, one in the end plate below control valve and the other in the center plate between the vacuum cylinders (Fig. 5). Remove pipe plugs and fill cylinder with vacuum cylinder oil to the level of the bottom of the holes. Re place pipe plugs. NOTE: The quantities of oil required are automatically controlled by the position of pipe plugs. They are located so as to es tablish the proper oil level.
3. Unscrew the ble'Cder valve 3/4 turn and

depress brake pedal by hand. Allow the pedal to return quickly to the MOFF" position. NOTE: Bleeding instructions for all vehicles having the residual check valve located in the master cylinder recommend allowing the brake pedal to return to the "OFF" position slowly. However, in brake systems where the residual check valve is located in the hydrovac slave cylinder end the brake pedal

HYDROVAC OIL CAPACITIES ARE AS FOLLOWS: APPROXIMA TE OIL CAPACITY HYDROVAC SIZE END CHAMBER
CENTER CHAMBER None None 4 ounces
6-3/4 11 Diam. Single Piston

9-1/211 Diam. Single Piston 9-112" Diam. Tandem Piston
I ounce 2 ounces 2 ounces
Hydrovac Air Inlet Filter (Fig. 7).

On all hydrovac installations, a filter is pro vided to clean the air entering the power chamber whenever the brakes are applied. This filter is located on the inside of cab below driver's seat. The air cleaner should be inspected every 1000 miles. If air passages are restricted, re move the air cleaner, dismantle and thoroughly clean all parts in a cleaning solvent and allow to drip dry. Then saturate the air cleaning elelTI.ent with a light oil, reassemble and install on vehicle. NOTE: Where the air inlet line is connected to the engine air filter, servicing the air filter as outlined in the Fuel System Maintenance Section will suffice, CAUTION: All hose connections lTI.ust be secure and leak-proof.
Hair filter element
Screen
Fig. 7 - Hydrovac"Air Inlet Fi Iter.
Vacuum Line Oil Bath Air Cleaner (Fig. 8).

On trucks having a separate air cleaner for the vacuum line, this unit is located on the engine side of cowl at upper right hand corner. The vacuum line air cleaner prevents any dirt or foreign lTI.atter being drawn into intake manifold when the brakes are applied. In normal operation, service the cleaner every 5000 miles by re moving oil reservoir, cleaning thoroughly in a suitable cleaning solution or kerosene and re filling with clean engine oil to indicated level on side of reservoir (Fig. 8). Use same grade of oil as used in engine crankcase. CAUTION: Be sure that reservoir seats per fectly against gasket and that clamp is correctly installed after completing service operation. Should a leak occur, the engine performance and hydrovac operation will be seriously affected.
Vacuum Connection Service

Rernove the vacuum connection elbow from the intake manifold every 10,000 miles and in spect the elbow and vacuum line for any possible obstruction. Clean the elbow and reinstall.
Fig. 8 - Vacuum Line Oil Bath Air Cleaner.
BRAKE TROUBLE CHART FOR VEHICLES EQUIPPED WITH HYDROVAC UNITS
TRUCK BRAKE TROUBLES ARE EASILY DIAGNOSED IF THE COMPLAINT IS UNDERSTOOD. THEY WILL ALWAYS SHOW UP IN ONE OR MORE OF THE FOUR WAYS LISTED BELOW. THE DRIVER MAY REPORT OTHER SYMPTOMS, BUT THESE WILL NOT HELP IN YOUR ANALYSIS. BE SURE TO HAVE THE DRIVER TELL YOU WHICH OF THESE FOUR CONDITIONS HE HAS NOTICED. IF AT ALL POSSIBLE; DRIVE THE TRUCK AND ACTU ALLY FEEL THE CONDITION.
THE "FOUR WAYS"

OR CONDITIONS
POSSIBLE SOURCE OF TROUBLE
No.1
Hard Pedal
1- Vacuum failure due to: (a) Faulty vacuum check valve. (b) Collapsed vacuum hose. (c) Plugged vacuum fittings. 2-Bound-up pedal shaft. 3-Glazed linings. 4-Grease or brake fluid on linings. 5-Hydrovac trouble.
No. 2
IIGrabby" Brakes
I-Grease or brake fluid on linings.

2-Scored drums.
3-Anchor pins bound-up.
4-Hydrovac valve trouble.
I-Brakes need adjustment. 2-Air in hydraulic system. No.3

3 -Hydraulic leak. 4-Master cylinder fluid - reservoir needs replen Pedal Goe s to Floor ishing. or almost to floor 5-Cracked drum. 6-Hydrovac leakage. I-Master cylinder compensating - post covered or plugged. 2-Anchor pins bound-up. 3-Bound-up brake pedal shaft. 4-Brakes improperly adjusted. 5-Faulty hydraulic check valve - at master cylinder or hydrovac. 6-Hydrovac valve or ball check trouble.
No.4 Brakes Fail to Release

Hydrovac Check
The following data will assist in the check ing of brake systems utilizing the Hydrovac Power Unit. The unit should be checked on the vehicle to determine that the trouble is not elsewhere in the brake system. The various units of the brake system should be checked individually for damage or misadjustment be fore proceeding with the hydrovac check. A good quick way to check the hydrovac, to determine whether it is operating at all, is as follows: 1. With the vehicle parking brake applied, clutch released, and trarlsmission in neu tral position; press the brake pedal to about a medium brake application and hold. 2. Turn the ignition switch to "ON" and start the engine.
4. Brakes:
Check brake shoe adjustment for proper clearances. Excessive shoe clearance will cause loss of pedal reserve travel. Insuf ficient shoe clearance may cause dragging brakes.
3. Sho rtly afte r the engine starts. the brake pedal pressure will be felt to relieve it self. This is caused by the Hydrovac pick ing up the brake application. The relief or movement is quite noticeable when the hydrovac is functioning properly.
If no movement or relief is felt at the brake pedal when making the above check, it is good practice to check the brake system further be fore centering attention on the hydrovac unit. Check as follows:
1. Master Cylinder Piston Rod Clearance: Make certain linkage is properly adjusted to permit opening of compensating port with brake pedal in normal full released position. Failure to properly uncover the compensating port may cause sufficient pressure to be maintained in the brake system to hold the hydrovac valve in a partially applied position and thus cause dragging brakes. 2. Restricted Vacuum Lines: Check for vacuum at the hydrovac by dis connecting the vacuum line at the hydrovac vacuum connection fitting and holding a thumb over the line, with the engine run ning. If no vacuum exists, or if air flow is slow, check vacuum line to manifold for kinks in tUbing and collapsed liners in hoses. Also test the check valve to be sure it opens. Check fitting at engine manifold for restriction. 3. Restricted Air Line and Air Cleaner: Disconnect the air cleaner line at the hy drovac and blow into the line. If the line is restricted, check for collapsed hose or tubing. Clean or replace air cleaner.
PRJNTED IN UNITED STATES OF" AMERICA
BRAKES AIR Section C Page 1
AIR BRAKES
(For Description and Operation see Shop Talk No. 24)
AIR BRAKE EQUIPMENT
Air brake equipznent on trucks and truck tractors provides a zneans of controlling the brakes through the znediuzn of coznpressed air. Air brake equipznent consists of a group of devices. Sozne znaintain a supply of coznpressed air, sozne direct and control the flow of the coznpressed air, and others transforzn the en ergy of coznpressed air into the znechanical forceandznotionnecessary to apply the brakes. Different types and sizes of devices are used on different types of vehicles to zneet the oper ating requireznents, but they are all fundaznen tally the sazne. Following are the devices coznprising a typical truck or truck-tractor air brake systezn, with a brief description of the function of each device.
Slack Adjusters
Slack adjusters provide a quick and easy znethod of adjusting the brakes to coznpensate for brake lining wear. One slack adjuster is used for the brakes on each wheel.
Cocks
Cut-out cocks are used in the trailer con nection lines to perznit these lines to be closed when they are not being used. Reservoir drain cocks are used also, znounted at the bottozn of the reservoir. The drain cocks perznit drain ing the oil and water which collects in the res ervoir.
Tubing and Tubing Fittings

Tubing and tubing fittings connect the different air brake devices in the air brake systezn.
Compressor
The coznpressor supplies the coznpressed air to operate the brakes.
Governor
The governor controls the coznpression of air by the coznpressor. Although the coznpres sor runs continuously when the engine is run ning, the governor, acting in conjunction with the unloading znechaniszn in the coznpressor cylinder head, stops and starts the coznpression of air by the coznpressor when the desired znax iznuzn and zniniznuzn air pressures are present in the air brakesystezn.
Hose, Hose Fittings, Hose Couplings and Dummy Couplings

Flexible hose lines and hose fittings are used where it is necessary to have an air line between two points of the vehicle which change their position in relation to one another. Hose lines also znake connections between two ve hicles, and in such cases they are provided with hose couplings to perznit the connections to be easily connected or disconnected. DUITIITIY couplings seal the hose coupling s against the entrance of dirt when the hose couplings are not in use. DUITIITIY couplings on the back of tractor cabs also provide a place for attaching the free ends of connecting hose that is not, being used.
Brake Valve
The brake valve controls the air pressure being delivered to the brake chaznbers and in this way controls the operation of the brakes.
Quick Release Valve

The quick release valve speeds the release of air pressure frozn the front wheel brake chaznbers.
Safety Valve
The safety valve protects the air brake systezn against excessive air pressure.
Relay Valve Reservoirs

The relay valve speeds the application and release of air pressure frozn the rear wheel brake chaznbers. Reservoirs store the coznpressed air until it is needed for brake operation and provide sufficient air pressure to znake several brake applications even after the engine has stopped.
Brake Chambers and Brake Cylinders

Brake chaznbers and brake cylinders trans forzn the ener gy of coznpres sed air into the zne chanical force andznotionnecessary to apply the brakes. One brake chaznber or one brake cylin der is used to operate the brakes on each wheel.
PRINTED IN UNITEO STATES OF AMER!CA
Air Gage
The air gage znounted on the instruznent panel of the vehicle registers the pressure in the ai r brake systezn.
BRAKES
AIR
Section C Page 2

In the case of the relay valve (6-wheel models), the connections lead to tee connections and from there to each of the four rear brake chambers. When the pressure built up in the brake chambers and acting against the brake valve diaphragm is enough to compress the regulat ing spring, the diaphragm moves upward, allow ing the inlet valve to close by action of its spring. The exhaust valve remains closed by action of the inlet valve spring and tilting of the rock er arm. Further increase of brake chamber pressure is thus prevented. If, however, there should be leakage from the brake chambers or piping, while the brake valve lever remains in this position, the resulting drop in pressure under the brake valve diaphragm will cause the regulating spring to again unseat the inlet valve and restore the lost pressure.
Air Supply Valve

In some cases the air supply valve is in cluded to provide an easy means of obtaining compressed air from the air brake system for such purposes as tire inflation.
Low Pressure Indicator

The low pressure indicator is often pro vided to warn the driver by sounding a buzzer or by lighting a warning light if for any reason the air pressure in the air brake system falls below a safe operating point.
Stop Light Switch

The air operated stop light switch provides a simple means of controlling the stop lights of the vehicle.
Air Horn
On some vehicles the air horn is included to provide an effective warning signal.
Release
When the foot is removed from the brake pedal, the brake valve lever is moved back toward normal position again, which relieves the tension on the regulating spring so that the diaphragm will be moved upward to its normal position by brake chamber pressure under neath it. This permits the exhaust valve to be unseated by its spring which opens brake cham ber line to atmosphere and allows air to ex haust from the brake chambers.
If the brake valve lever is moved all the way back to normal position and left there (foot entirely removed from brake pedal), the brakes will entirely release, but if moved only part way back (foot pressure eased), the brakes will only partially release, Le., the exhaust valve will remain open until the brake chamber pres sure has reduced to such an amount as will no longer hold the diaphragm up, whereupon the regulating spring will move the diaphragm, with rocker arm, downward again and close the exhaust valve.
Alcohol Evaporator
On some vehicles the alcohol evaporator is included to prevent moisture freezing in the air brake system.
OPERATION OF THE AIR BRAKE

EQUIPMENT
Charging
The reservoirs are charged with air by the compressor. The reservoir air has access to the inlet valve chamber of the brake valve and the inlet valve is then held closed by the tension of its spring and air pressure.
Service Application
When it is desired to apply the brakes, foot pressure is applied to the brake pedal, which action is carried through the brake rod pulling up on the lever of the brake valve. This com presses the spring, deflects the diaphragm downward, and through the medium of the rock er arm closes the exhaust valve and opens the inlet valve. Air is thereby admitted from the reservoir to the brake valve, thence out the two side outlets to the front and rear brake cham bers. The power thus exerted against the brake chamber diaphragms or pistons forces the push rods out, rotating the camshafts to apply the brakes. In flowing to the rear brake chambers the air pressure passes through the quick release valve ente ring at the top, deflecting the dia phragm and its seat to seal the exhaust open ing while the air pressure passes around the diaphragm to the two side connections, each leading to a brake chamber.
The brake chamber line to the rear wheels is released only up to the quick release valve or relay valve. This allows the diaphragm to un seat, uncovering the exhaustportthrough which the rear brake chambers are then exhausted.
OPERATING INSTRUCTIONS
Operating the brakes of an air-braked ve hicle differs very little from operating the brakes of a passenger car. Because operation of the brake pedal requires very little physical effort, proper control of the brakes is easily accomplished.

The distance the brake pedal is depressed determines the amount of air pressure deliv ered to the brake chambers, and the brake chamber pressure determines the braking force. Thus the driver may definitely control the brakes of the vehicle by keeping in mind the fact that he is operating a brake valve capable of giving finely graduated brake con trol and making full use of this feature. An air-braked vehicle should not be moved unless the air gage shows at least 60 pounds air pressure in the air brake system, because the brakes are not fully effective at lower pressures. While operating the vehicle, the driver should periodically observe the air pressure registered by the dash gage, to be sure it is being maintained properly. If the air pressure drops to a low point, or if the warn ing buzzer or light signifies the pressure is low, the vehicle should be stopped and the trouble corrected. The best stop results when the brake ap plication is as hardat firstas the speed, condi tion of the road, and passenger comfort permits, and then graduated off as the speed decreases. As the stop is completed, there should be only sufficient air pressure in the brake chambers to hold the vehicle stationary. The brakes must never be applied lightly at first and the braking pressure increased as the speed decreases, as this will result in a very rough stop. The brake pedal should not be "fanned," as this merely wastes compressed air and has no bearing on correct br.aking results. The brake pedal should not be fully de pressed except in cases of emergency as this causes full braking force to be delivered to the wheels and this should not be necessary in ordinary service. Normally the engine is used to assist the brakes by not disengaging the clutch until the engine reaches idling speed. In the event a trailer breaks away from a truck or tractor, the driver must immediately apply the brakes and bring the truck or tractor to a stop. Then the truck or tractor should be held with the hand brake while the cut-out cocks in the emergency and service lines are closed. The truck or tractor air brake system will then be recharged to normal pressure. When disconnecting trailers from trucks or tractors, the emergency feature of the air brake system on the trailer is often used to lock the trailer brakes. This is approved practice but the air brake system mustnotbe depended upon to hold a vehicle parked. The parking brake must always be applied or the wheels blocked.
PRINTED IN UNITO STATES OF AMERICA
COMPRESSOR (TYPE U)
Fig. I - Air Compressor Installed.

IDENTIFICATION. All Bendix - Westing house compressors are identified by the number stamped on the name plate riveted to the side of the crankcase. Name plates also show the serial number and type of the compressor but compressors cannot be identified by the serial number or the type designation. The type designation shown on the name plate is in accordance with the following: Type Number Rated Luof of CaCom- briCylinpaccation ders !presity sor 2 or 3 Type of Mount ing Type of Cooling
Eng.- 4,6, Flange-F Air-A E or 7-114 Horiz. -H Water-W self-S orl2 Verti cal-V
Thus a 2 UE 7-1/4 VW compressor is a two cylinder, type U, engine-lubricated compressor with a displacement of 7-114 cubic feet per minute at 1250 r.p.m., vertically mounted and water-cooled.
PREVENTIVE MAINTENANCE AND

TROUBLE SHOOTING
Daily Service
(a) International trucks are usually equipped with the engine lubricated type air compressor, however, if the compressor is of the self-lub ricated type, check the oil level in the compressor crankcase and replenish if nec essary.

(d) ReITlove cOITlpressor discharge valve cap nuts and check for presence of excessive carbon. If excessive carbon is found, clean the COITlpressor cylinder head; also check COITl pressor discharge line for carbon and clean or replace the discharge line if necessary.
(b) Should it be nec e s sa ry to d rain the engine cooling systeITl to prevent freezing, al ways drain the cOITlpressor cylinder head (see Fig. I).
Every Month or After Each 2,000 Miles

(a) Service cOITlpressor air strainer. Re ITlove and wash all parts including curled hair in cleaning solvent. Saturate curled hair with clean engine oil and squeeze dry before re placing it in the strainer. (b) If COITlpressor is the self-lubricated type, drain and flush COITlpressor crankcase and refill with clean engine oil. (c) Check cOITlpressor ITlounting and drive for alignITlent, belt tension, etc. Adjust if nec essary.
Inspection
1. Be sure cOITlpressor air strainer is clean and properly installed. Also be sure blanking covers and gaskets are installed on all strainer openings not being used in the COITl pressor intake ITlanifold.
z. With cOITlpressor running, check for noisy operation and oil or water leaks.
3.
Check unloader valve clearance. 4. Check cOITlpre ssor drive for alignITlent, belt tension, etc. 5. Check to be sure cOITlpressor ITlounting bolts are secure.
Operating Tests
Because of the ITlany different types of air brake systeITls found on different types of vehicles, it is difficult to set up any specific series of tests to deterITline the serviceability of a COITlpressor on a vehicle. Failure of the cOITlpressor to ITlaintain norITlal air pressure in the air brake systeITl of a vehicle usually denotes loss in efficiency due to wear, provided leakage in the reITlainder of the systeITl is not excessive. Another sign of wear is excessive oil passing. lfeitherof these conditions develop and inspection shows the reITlainder of the air brake equipITlent to be in good condition, the cOITlpressor ITlust be repaired or replaced.
DISCHARGE
PORT
Fig. 2 - Adjusting Compressor Unloading Valve Clearance.
Air Leakage Tests

1. Excessive leakage past the discharge valves can be detected by fully charging the air brake systeITl and then with the engine stopped, carefully listening at the COITlpressor for the sound of escaping air. This ITlust be done in a quiet place and if air pressure can be heard escaping inside the COITlpressor, the discharge valve leakage is excessive, and the cOITlpressor cylinder head or the cOITlplete COITlpressor ITlust be replaced. Z. With the airbrake systeITlfully charged (governor cut out) coat the unloading box cover with soapsuds to check for leakage past the unloading diaphragITls. Leakage of a one-inch soap bubble in three seconds is perITlissible. If excessive leakage is found, the cOITlpressor cylinder head or cOITlplete cOITlpressor should be repaired or replaced.
Every Six Months or After Each 10,000 Miles

(a) If the cOITlpressor is lubricated froITl the engine, dean oil supply line to cOITlpressor. (b) Check cOITlpressor unloading valve clearance and adjust if necessary (Fig. Z). Clearance ITlust be 0.010 inch ITliniITluITl to 0.015 inch ITlaxiITluITl. To adjust clearance, loosen lock nuts and turn adjusting screws until proper clearance is obtained. Then tighten lock nuts. Clearance can be checked only when governor is cut in (coITlpressor not unloaded). Check unloading valve lever for binding. (c) If cOITlpressor is the self-lubricated type, service crankcase breather. Wash breath er in cleaning solvent.

Trouble Shooting
Dirty intake strainer. Excessive carbon in com. pressor cylinder head or discharge line. valves leaking. Di Com.pressor fails to m.aintain Excessive wear. adequate pres sure in the air Drive belt slipping. brake system.. No clearance at com.pressor unloading valves. Unloading valves stuck open. Excessive leakage of unload ing valves. Excessive wear.
Dirty air strainer.
Excessive oil pressure.
Com.pressor passes exces sive oil. Oil return line or passage to
crankcase plugged. Com.pressor flooded. crankcase from. engine
Air inlet from. ~.~. . . . reservoir ~
BRAKES AIR Section C
BRAKE VALVE
(See Fig. 3) Description

The brake valve is fitted with a lever suit able for connecting to the brake pedal. The pedal controls the m.ovem.ent of an inlet valve and exhaust valve which in turn controls the air pressure being delivered to or released from. the brake cham.bers on the vehicle. To fully apply the brakes, the brake pedal m.ust be fully depressed; whereas when the pedal is only partially depressed, correspondingly less braking force is developed. In other words,
Boot--_ _:a..
Oil rings stalled.
im.properly
in
Fig. 3 - Brake Valve.

the farther the driver depresses the pedal, the greater the air pressure delivered to the brake cham.bers and the m.ore effective the brake ap plication. At any tim.e the brakes of the vehicle m.ay be partially released by the driver per m.itting the, brake pedal to partially return towards released position or they m.ay be en tirely released by perm.itting the pedal to re turn to full released position. In this m.anner the am.ount of force being applied to the brakes of the vehicle is always under control of the driver.
Back lash in drive coupling or drive gears. Loose drive pulley. Noisy operation. Excessive carbon in cylinder head or discharge line. Worn or burnt-out bearings. Excessive wear.
De f e c t i v e
unloading dia-
Preventive Maintenance Every Month or After Each 2,000 Miles
Com.pressor does not unload.
Excessive clearance at un loading valves. Unloading cavity plugged with carbon. Unloading m.echanism. bind ing or stuck.
PRINTE:O IN UNfT!::O STATES OF' "MERICA
(a) Lubricate all linkage between the brake valve and brake pedal; also lubricate the brake valve lever pin. (b) Check to be sure that no strain is placed on the brake valve lever, because the lower edge of the lever cap strikes the cover when the brake pedal is fully depressed. Adjust

2. Hold brake pedal at several different positions between release position and fully de pressed position and observe that intermediate delivered pressures between five and seventy pounds aredefinitelydeterminedby the position in which the brake pedal is held.
pedal stop or linkage, if necessary, to prevent this interference. After any adjustment, check brake valve delivery pressure. (c) Be sure the brake valve lever strikes the cover of the valve' when the brake pedal is in released position. If necessary, adjust pedal rod length.
Lever pin ...-. --.,..
Leakage Tests
l. With brakes released, coat the exhaust port with soapsuds. 2. With brakes fully applied, coat the ex haust port with soapsuds. 3. Leakage in excess of a one-inch soap bubble in one second is not permis sible in either of these tests. If excessive leakage is found, the brake valve must be repaired or replaced.
Diaphragm _ . _ - j 7 i
Return spring ---RH~a~;t

Seal---ti~m~aJi!.~
4. With brakes applied check for leakage out the top of the brake valve. No leakage is permissible. If leakage is found, the brake valve must be replaced.
BRAKE VALVE
(Hand Operated) Type HP
Seal-----
Description
A.22837
Fig.
- Sectional View Of Brake Valve.
Testing For Serviceability

Operating Tests
1. Check the delivery pressure of the brake valve using an accurate airpressure test gage. On vehicles having trailer connections the test gage may be conveniently connected to the service line outlet at the rear of the ve hicle. Note that the first movement of the brake pedal towards applied position, after the slack is taken up, causes the brake valve to deliver approximately five pounds air pressure. Note that approximately full reservoir pressure is delivered by the brake valv~ when the brake pedal is fully depressed. If the brake valve does not deliver approximately full reservoir pressure, when the brake pedal is fully de pressed, adjust the pesal stop or linkage so as to increase the travel of the brake valve lever. This should increase the delivered pressure. On some vehicles the pedal stop is so arranged as to prevent the brake valve from delivering full reservoir pressure. This arrangement must not be altered on such vehicles unless a higher delivery pressure is desired in order to increase the effectiveness of the brakes. When making this adjustment, be sure no strain is placed on the valve lever due to the edge of the lever cap striking the cover when the brake pedal is fully depressed. Also be sure the brake valve lever returns to full release position when the brake pedal is released.
Type HP brake valves (Fig. 5) are used for controlling the brakes on a trailer independent ly of the brakes on the towing vehicle. They are usually mounted on the steering column or on the dash and the driver may put the handle in anyone of several positions between brakes released and brakes fully applied position so the brakes on the trailer are kept applied until the brake valve handle is returned to release position. The distance the brake valve handle is moved in a clockwise direction toward ap plied position determines the severity of the brake application. The driver may, therefore, control the brakes on the trailer as the speed, load, and road conditions require.
..
m=====~
__
-------HANDLE
fRIGION LOCK
.:!~~iliiiii~-.L.._~_ EXHAUST
VALVE
riliicr-+----INlET VALVE
==-__
INLET PORT
Fig. 5 - Sectional View Of Hand Brake Value.

Testing for Serviceability (Hand Brake Valve) Operating Tests
1. Check the delivery pressure of the brake valve using an accurate air pressure test gage. The test gage may be conveniently con nected to the service line outlet at the rear of the vehicle. With the brake valve handle moved to its fully applied position, the brake valve must deliver at least sixty pounds pressure.
2. Move the brake valve handle to several different positions between fully applied and fully released positions and observe that the air pressure registered by the test gage varies in accordance with the position to which the handle is moved.
INLET PORT
BRAKE
BRAKE
CHAMBER
PORT
CHAMBER
PORT
Fig. 6 - Sectional View Of Quick Release Valve.

Operating Tests
Apply the brakes and observe that when the brakes are released, air pressure is quickly exhausted through the exhaust port of the valve. Be sure the exhaust port is not restricted in any way. The valve must be tested at regular inter vals for leakage by applying soapsuds on the exhaust port with the brakes applied. On re leasing the brakes see that the valve releases immediately with the corresponding return movement of the foot pedal. Leakage may be caused by dirt in the valve or a defective dia phragm. As a rule the diaphragm should be replaced at least once every year. The air line from the brake valve to the rear wheel chambers is released back to the quick release valve. This allows the .diaphragm in the quick release valve to unseat, uncovering the exhaust port in the valve and permitting the air in the brake chambers to escape quickly at the quick release valve. On some trucks air is released from the front wheel brake chambers back through the lines to the foot brake valve and exhausted at that point. Where this is the case, the quick release valve housing installed at the front of the vehicle serves merely as a connector and does not contain either a diaphragm or dia phragm spring and the exhaust opening in the quick release valve housing is closed with a plug. IMPORTANT: DO NOT REMOVE' THIS PLUG, TO DO SO WILL RENDER THE FRONT WHEEL BRAKES INOPERATIVE.
Leakage Tests
1. With brake valve handle in released position. coat the exhaust port with soap suds to check for leakage. 2. With brake valve handle in fully applied position, coat the exhaust port with so,ap suds to check for leakage. 3. Leakage in excess of a one inch soap bubble in one second is not permissible in either of these tests. If excessive leakage is found it will usually be caused by dirty or worn valves or valve seats and the inlet and exhaust valve assembly or the complete brake valve must be repaired or replaced. Leakage due to dirty valves and valve seats may be corrected by removing the inlet and exhaust valve assembly and cleaning the valves and valve seats. Leak age due to worn valves maybe corrected by in stalling a new inlet and exhaust valve assembly. If the valve seats are pitted or worn excessive ly or if the installation of a new inlet and ex haust valve assembly does not correct the leakage, the brake valve must be repaired or replaced.
QUICK RELEASE VALVE Description

The purpose of the quick release valve is to reduce the time required to release the brakes by hastening the exhaust of air pressure from the brake chambers. It is most commonly used with front wheel brake chambers. The valve consists of a body containing a spring loaded diaphragm so arranged as to per mit air pressure to flow through the valve in one direction; but when the supply pressure is reduced, the air which has passed through the valve is permitted to escape through the ex haust port (Fig. 6).
J>AINTEO IN UNITED $T.t.TS Of' AMERICA
Leakage Tests
1. With brakes released, coat the exhaust port with soapsuds to determine leakage. 2. With the brakes fully applied, coat the exhaust port with soapsuds to determine leak age.

in pressure and raises, lowers, or completely exhausts the air pressure in the rear brake chambers as the brake valve raises, lowers, or completely exhausts air pressure from it.
'BRAKE VALvE PORT
3. Leakage in excess of a one-inch. soap bubble in one second is not permissible in either of these tests. If excessive leakage is found, the relay valve must be repaired or replaced.
DOUBLE CHECK VALVE
Description
A double check valve is used on the tractor truck at the frame side rail (Fig. 7). It is con nected into the air lines from the relay valve to the trailer lines. The purpose of the double check valve is to control the brakes on the trailer or towed load. If the double check valve were not used when one of the brake valves was moved to its applied position, air pressure from the reservoir would escape through the exhaust port of the other brake valve, whose exhaust valve would be open. When the double check valve is used and one of the brake valves is moved to the applied position, the double check valve blocks off the line leading to the other brake valve, in this manner preventing any loss of air pressure through the open ex haust valve of the brake valve not being oper ated.
DIAPHRAGM DIAPHRAGM GUIDE GUIDE RING
:~~i~~~f~ ~~!l
g..==-;---BY.PASS PORi
EXHAUST PORi SUPPLY VALVE RESERVOIR PORT -----+-!!~~~
1.9357
Fig. 8 - Sectional View Of Relay Valve. Testing for Serviceability Operating Tests
1. With the air brake system charged, apply brakes and check to be sure the rear wheel brakes controlled by the relay valve ap ply promptly. 2. Release brakes and check to be sure air pressure is exhausted from the exhaust port of the relay valve promptly.
Leakage Tests
OUTLEI
1. With brakes released, coat the exhaust port with soapsuds to determine leakage. 2. With brakes fully applied, coat the ex haust port with soapsuds to determine leakage. 3. Leakage in excess of a one-inch soap bubble in one second- is not permissible in either of these tests. If excessive leakage is found, the relay valve must be repaired or
Fig. 7 - Sectional View Of Double Check Valve. Testing

With the brake system fully charged and both brake valves in released position, move one of the brake valves to applied position, and check with soapsuds for leakage at the exhaust port of the brake valve not being operated. Re peat test with the other brake valve. Leakage in excess of a 3-inch soap bubble in 3 seconds is not permissible. If excessive leakage is found, the defective double check valve must be replaced.
GOVERNOR (TYPE 0-1)
Description
The purpose of the compressor governor is to automatically control the air pressure being maintained in the reservoirs of the air brake system by the compressor, between the maximum pressure desired (100-105 Ibs.) and the minimum pressu.re required for safe brake operation (80-851bs.). To understand this func tion of the governor, it should be remembered that while the compressor may run continuous ly, actual compression of air is controlled by the governor, which, acting in conjunction with the compres sor unloading mechanism, or starts compression when these maximum and minimum reservoir pressures are reached.
RELAY VALVE
Description
The relay valve (Fig. 8) up the ap plication and release of the rear wheel brakes. It is controlled by the brake valve and keeps the air pressure in the rear brake chambers the same as the pressure being delivered by the brake valve. It reacts to even slight changes

TUBE
.BRAKES AIR
Section C Page 9
ADJUSTING SCREW BRACKET
UPPER VAtVE GUIDE
Z. With engine running, slowly reduce the air pressure in the air brake system by applying and releasing the brakes and observe at what pressure registered by the dash gage the governor cuts in and compression is re sumed. The governor must cut in between 80 and 85 pounds. 3. Before condemning or adjusting the pressure settings of the governor, be sure the dash gage is registering accurately. This may be done by using an accurate test gage to check the pressure registered by the dash gage. 4. When necessary, the pressure settings (cut-in and cut-out pressures) may be adjusted after removing the cover. The pressure set tings are raised by loosening the adjusting screw lock nut and turning the adjusting screw clockwise viewed from the top (Fig. 9). Pres sure settings may be lowered by turning the adjusting screw counterclockwise. The lock nut must be tightened after any adjustment. 5. If the governor cannot be adjusted to cut-in and cut-out at the proper pressure set tings, it should be replaced.
TO COMPRESSOR
UNLOADING MECHANISM
STRAINER
lOWER VALVE SPRING
fROM RESERVOIR
A-9J66
Fig. 9 - Sectional View Of Governor.

The design of the compressor governor is based on the principle of a Bourdon tube which is a flattened metal tube bent to a curve that tends to straighten under internal pressure (Fig. 9). This reaction by the tube, due to changes in the air pressure in the tube, in creases or decreases the spring load on the valve mechanism of the governor and makes the valve mechanism assume its "cut-in" or II cut outll positions in accordance with the air pressure in the reservoir. Two types of gover nor cases will be found in service, one being a die cast case and the other a pressed steel case. Both types of cases are interchangeable with each other and the working parts of the governor used in both types of cases are iden ticaL
6. Adjustment of the range between the cut-in and cut-out pressure is made by remov ing shims beneath the upper valve guide (Fig. 9) to increase the range or by installing addi tional shims to dec rease the range.
Leakage Tests
1. Remove cover and with the governor in its cut-out position, test for leakage by ap plying soapsuds to the exhaust port. Z. With the governor in its cut-in position test for leakage by applying soap suds to the exhaust port. 3. Leakage in excess of a one-inch soap bubble in three seconds is not permissible in either of the above tests. If excess leakage is found. the governor must be replaced. 4. Install cover after making tests.
Preventive Maintenance Every Six Months or After Each 10,000 Miles

Remove the governor air strainer and wash all parts in cleaning solvent. L,amb IS wool in the air cleaner may be used again if it can be washed thoroughly clean in cleaning solvent, otherwise it must be replaced.
Every Year Or After Each 25,000 Miles

(a) parts. Disassemble governor and clean all
SAFETY VALVE Description

1. The purpose of the safety valve is to protect the air brake system against excessive air pressure. Should the air pressure in the air brake system rise above the setting of the safety valve at 150 pounds. the valve opens and permits pressure above 150 pounds to be ex hausted. It is located on one of the reservoirs. Z. The safety valve consists of a spring loaded ball check valve which is set to "blow offll at 150 pounds air pressure. (Fig. 10).
(b) Cleanorreplaceboth tubing lines con necte'd to the governor.
Testing for Serviceability and Adjusting Operating Tests

1. With the engine running, build up air pressure in the air brake system and observe. at what pressure registered by the dash gage the governor cuts out stopping further com pression. The governor must cut out between 100 and 105 pounds.
BRAKES
AIR
Section C Page 10

approximately 100 pounds releasing the brakes. by applying and
ADJUSTING SCREW
..
Leakage Tests
With the air brake system -fully charged to approximately 100 pounds, coat the safety valve all over with soapsuds to check for leak age. Leakage of a I-inch soap bubble in 5 seconds is not permissible. Slight leakage may sometimes be corrected by lightly tapping the end of the release pin. If this fails to correct the leakage, replace the safety valve.
SLACK ADJUSTER
BAll VALVE ---+-e....
Description
One slack adjuster is used at each brake chamber. Slack adjusters consist of a worm and gear enclosed in a body which also serves as an adjustable lever (Fig. 11). They provide a quick and easy means of adjusting the brakes to compensate for brake lining wear. During brake operation, the entire slack adjuster ro tates bodily with the brake camshaft. During brake adjustment, the worm moves the gear so as to change the position of the lever arm in relation to the brake camshaft.
A-9348
Fig. 10 - Sectional View Of Safety Valve.

Testing Pressure Setting Tests
1. Connect a test gage known to be accu rate into the air brake system so as to register reservoir pressure. A simple way to do this is to connect the air gage to the emergency line at the rear of the tractor truck and open the emergency line cut-out cock. With the motor running, temporarily stop governor operation by turning the air supply valve on the dash panel to its air supply position, and permit the air pressure in the air brake system to rise until the test gage registers 150 pounds. When the test gage reaches 150 pounds, the safety valve must release, or "blow of." If the safety valve does not release, stop the engine imme diately, and adjust the pressure setting of the safetyvalve. Do not permit air pressure in the air brake system to build up higher than] 50 pounds, otherwise the compressor may become damaged. 2. To adjust the pressure setting of the safety valve, loosen the lock nut and turn the adjusting screw. Turning the adjusting screw counterclockwise lowers the pressure setting. Turning the screw clockwise raises the pres sure setting. Turn the adjusting screw as re quired until the safety valve releases at 150 pounds pressure registered by the test gage. Then tighten the lock nut to hold the adjusting screw at the proper setting. Reduce air pres sure in the air brake system to normal of
Spring loaded sleeve type adjusting screw
Slack
adjuster
lock
A-.22838
Fig. II - Sectional View Of Slack Adjuster.
L-LINE MOTOR TRUCK SERV1CE MANUAL

Testing
Adjust brakes and note brake chamber push rod travel when brakes are applied. Make several brake applications, and again check push rod travel. Push rod travel must remain the same as it was after adjustment. If the push rod travel inc reases, or if difficulty is experienced in keeping the brakes adjusted in service, the slack adjuster n;lUst be replaced. When slack adjuster movement does not give the desired brake action, adjustment of the push rod length by altering the location of the yoke may be necessary. With brakes re leased the angle formed by the push rod and slack adjuster must be greater than 90 0 , and all slack adjusters should be set at the same angle. With the brakes fully applied, after be ing adjusted, this angle should still be greater than 90 0 In other words, the slack adjuster should not go "over centerlt when the 'brakes are applied (Fig. 13). The position of the push rod yoke on the push rod should be adjus ted if necessary until these conditions prevail.
Push locking sleeve in to diseng-;ge

This illustration shows the locking sleeve in its disen gaged position. Be sure this is held in, disengaging the ad justing screw, when making adjustments. Use either an open end or socket wrench in making adjustment. Make certain locking sleeve is held in, thereby disengaging the locking mechanism. Never use a wrench on the sleeve portion.
A22908
Maintenance
The worm gear and worm should be kept well lubricated. This can be done by removing the plug and filling the cavity with a good grade of chassis lubricant every 1,000 miles.
Fig. 12 - Illustrates locking Sleeve On Adjust ing Nut.

CENTER LINE OF SLACK ADJUSTER IN APPLIED POSITION SHOULD NEVER GO OVER CENTER - - -......
LOW PRESSURE INDICATOR
APPLIED -----i.~1
Description
The low air pressure indicator (Fig. 14). is a safety device designed to give an automatic warning whenever the air pressure in the air brake system is below approximately 60 pounds. Operating as an air-controlled switch of an electrical circuit, the low pressure indicator automatically sounds a buzzer when the air pressure drops too low. On some vehicles a light is used to indicate low pressure, in place of the buzzer.
~\\\--R-E..... \ LEASED
\
Testing
1. Drain air brake system, turn on igni tion key, and start engine: The low pressure indicator buzzer must sound until the air pres sure in the air brake system reaches a point between 54 and 66 pounds when the buzzer must stop sounding. 2. Continue to build up air pressure in the airbrake system until the pressure reaches at least 75 pounds, stop engine, and reduce the air pressure in the air brake system by mak ing brake applications. Check to see at what pressure the buzzer again sounds. The buzzer must sound when the pressure in the air brake system reaches a point between 66 and 54 pounds.
PRINTED IN UNITED STATES OF AMRICA
THIS ANGLE /
NEVER LESS THAN
90
BRAKES AIR
Section C Page 12

2. With brakes applied, coat the stop light switch with soapsuds to check for leakage. No leakage is permissible. If is found, the stop light switch must be replaced.
i+---I- DIAPHRAGM
FROM RESERVOIR
AIR INLET
A.9354
Fig. 1& - Sectional View Of stop Light Switch.

BRAKE CHAMBER (BENDIX-WESTINGHOUSE)
A-9353
Fig. I~ - Sectional View Of cator.

Leakage Test
Low Pressure Indi
The Bendix-Westinghouse brake chamber consists of two dished metal plates, namely: the non-pressure plate, and the pressure plate separated by a diaphragm (see Fig. 16).
With the air brake system fully charged, coat the outside of the low pressure indicator with soapsuds to check for leakage. No leakage is permissible. Leakage at the lower diaphragm screw can sometimes be corrected by removing the electrical connection and carefully tighten ing the terminal screw nut. Leakage through the small vent hole in the cover signifies a leaking diaphragm, and the low pressure indi cator must be replaced.
Air inlet Dust shield
STOP LIGHT SWITCH
Push rod Pusb rod
Description
The stop light switch is mounted on the left-hand frame side :cail. Stop light switches are electro-pneumatic switches which close the stop light electrical circuit when the brakes are applied (see Fig. 15).
Testing
1. With all air pressure exhausted from the air brake system, move the brake valve to applied position, and start the engine. Observe at what pressure registered by the dash gage the stop lights light. Stop lights must light be fore the dash gage registers 10 pounds pres sure.
A22923
Fig. 16 Type}
Typical
Brake
Chamber
(Oiaphragm
In front of the diaphragm are the non-pres sure plate, push rod and push rod spring. Be hind the diaphragm is the air-tight cavity into which is connected a tubing line from the brake

valve. Due to the extreme sensitivity of the diaphragm, this arrangement permits push rod to respond to the slightest variation of air pres sure from the brake valve, thus permitting the driver to apply or release brakes as rapidly or gradually as the various road and operating conditions warrant. In order to meet requirements for different braking forces, brake chambers are made in several different sizes. All sizes are made for several different types of mountings, such as stud mounting, bracket mounting, and flange mounting. The following table shows different types of standard brake chambers: Outside Type Diameter A
B
Testing for Serviceability Operating Tests

I. Apply brakes and observe that push rods move out promptly without binding. 2. Release brakes and observe that push rods return to release position promptly with out binding. 3. Check travel of push rods to be sure it is at the minimum without brakes dragging.
Caution!
Always be sure the correct release spring is used in any brake chamber. Also be sure the brake chamber on the opposite side of the axle of the vehicle has the same release spring; otherwise uneven braking will result.
If a new diaphragm is installed in the brake chamber on one side of the vehicle, a new one also should be installed in the corresponding brake chamber on the other side, otherwise this may also cause uneven braking.
Maxi-I Effective Normal mum MaxiArea Working Work- mum Square Stroke ing Stroke Inches Stroke 12 24 16 6 9 36 30 5/8" 3/4" 3/4" 1/2" 5/8" 3/4" 3/4" 1-3/8" 1-3/411 1-3/4" 1-11411 1-3/8" 2-1/4" 1-3/4" 1-3/4" 2-114" 2-1/4" 1-5/8" 1_3/4" 3"
2-1/2"

C
D
E F G
6-15116 11 9-3116" 8-1116" 5_114" 6" II" 9-7/8"
Preventive Maintenance Every Month or After Each 2,000 Miles

Check travel of brake chamber push rods and adjust brakes ifnecessary. Push rod travel should be kept at the minimum without brakes dragging. Excessive travel shortens the serv ice life of brake chamber diaphragms and also results in slow braking response.
After the brake chamber is installed the brakes must be adjusted and checks made to be sUJ:'e the linkage does not bind. Adjustment of the push rod length by altering the location of the yoke may be necessary. With brakes re leased the angle formed by the push rod and slack adjuster must be greater than 90 0 , and all slack adjusters should be set at the same angle. With the brakes fully applied, after be ing adjusted, this angle should still be greater than 90 0 In other words, the slack adjuster should not go "over center" when the brakes are applied (Fig. 13). The position of the push rod yoke on the push rod should be adjusted if necessary until these conditions prevaiL
Every Year or After Each 50,000 Miles

Disas semble brake chambers and clean all parts. Install new diaphragms. When replac ing release springs be sure to use the correct spring, otherwise uneven braking will result.
BRAKE CHAMBER - PISTON TYPE (MIDLAND)

The Midland air cylinder (Fig. 17) requires very little attention, but to insure proper oper ation, the cylinder should be kept lubricated. At intervals of approximately four months or 15,000 miles, the air connection at the rear of the cylinder should be removed and one quarter pint of lubricant (similar to Elsols (I50-LO) graphite type grease with 10<10 neat1s-foot oil), inserted. At regular truck overhaul periods, the cylinder should be removed, taken apart and thoroughly cleaned. The piston cup should be inspected and free from cracks, scratches and dirt particles. If the piston cup is hard or dry, it should be immersed in neat's foot oil before reassembling in cylinder. If it becomes nec essary to replace the piston cup, shellac both
Leakage Tests
1. With brakes fully applied, coat the brake chamber bolting flanges holding the dia phragm in place with soapsuds to check for leakage. No leakage is permissible. If leakage is found, tighten flange bolts. All flange bolts must be tightened evenly but only sufficiently to prevent leakage, otherwise the diaphragm will be distorted and premature failure will result. 2. With brakes fully applied, check for leakage through the diaphragm by coating the clearance hole around the push rod and the drain hole in the non-pressure plate with soap suds. No leakage is permissible. If leakage is found, the diaphragm must be replaced.

pressures registered by the gage over its normal pressure range with the pressures registered by a test gage known to be accurate. 2. A dash gage which loses its accuracy must be replaced. The continued use of a dash gage showing an error of more than 5 pounds is not recommended.
sides of piston stem plug gasket. also shellac threads of piston stem plug and draw up piston stem plug just snugly on ball end of piston stem. The inside of the air cylinder and complete piston assembly should be thoroughly cleaned and the wall of the cylinder. as well as the en tire piston assembly, should be covered with a lubricant as outlined in first paragraph. Clean breather hair in piston stem assem bly with cleaning solvent and dip in light lubri cating oil before replacing. Care should be exercised to make sure the rubber boot is in good condition and properly installed to protect the piston shaft from the element.
End cliver --l~~~====~~?r~
CUT -OUT COCKS
Description
1. Cut-out cocks have a tapered key ground to the body to prevent leakage. A pas sage is provided th;rough the key so that when the key is turned to its open position air is permitted to flow through the cock, but when the key is turned to the closed position air is prevented from flowing through the cock. Cut out cocks are used in the service and emergency lines of the tractor truck to provide a means of closing off these lines when they are not being used. 2. The cut-out cock is open when the handle is at a 90-degree angle with the body of the cock, and closed when the handle is parallel with the body of the cock; Stops are provided so that the handle cannot be turned beyond its normal positions.
Piston rod Piston stem Spring

A-22925
3. Always open and close a cut-out cock by hand. Never strike the handle with a ham mer, or similar instrument, as the cock would be damage~ and leakage would develop.
Fig. 17 - Typical Brake Chamber (Piston Type).

AIR PRESSURE GAGE
Testing
1. With brakes applied and cut-out cock closed (hose line disconnected), test with soap suds for leakage past the key. Also check for leakage through the body by coating the outside of the cut-out cock with soapsuds. 2. With brakes applied and cut-out cock open (hose line connected), check for leakage through the body by coating the outs ide of the cut-out cock with soapsuds. 3. Leakage in excess of a 3-inch soap bubble in 3 seconds in either of these tests is not permissible. 4. Leakage is caused by a dirty or scored key or body. Leakage due to dirt is corrected by cleaning parts and applying a light coating of cup grease to the key. Leakage due to a scored key or body cannot be repaired, and the cut-out cock must be replaced.
Description
1. The purpose of the dash-mounted air pressure gage is to register the amount of air pressure in the air brake system. While air pressure gages of this type are commercially accurate, they must never be confused with, or substituted for, test air gages which are in tended primarily for accurately checking air pressure in the air brake system. 2. Only test gages known to be accurate are to be used for chec:kingbrake valve delivery pressures, gover~or pressure settings, and other tests. Test gages differ from ordinary dash gages in respect to material and workman ship much as an expensive watch differs from a cheaper one, and due to these differences they are more accurate over their entire range, and maintain their accuracy over longer periods.
Testing
1. Check the dash air gage for accuracy. The simplest way to do this is to compare the
RESERVOIRS
1. Reservoirs are tested against a 200 pound pressure, and treated on the inside with a rust preventive.

2. The purpose of reservoirs is to provide a place to store compressed air so that there will be an ample supply available for immediate ~se in brake operation. They also provide stor age for sufficient compressed air to permit several brake applications after the engine has stopped. Another function of a reservoir is to provide a place where the air, heated during compression, may cool and cause the oil and water vapors to condense.
2. Always open a drain cock by hand. Never strike the handle with a hammer or any other instrument, as the cock would be damaged and leakage would develop.
Testing
1. With the air brake system charged, test with soapsuds for leakage past the key. Also check for leakage through the body by coating the outside of the drain cock with soap suds. Leakage in excess of a 3-inch soap bub ble in 3 seconds is not permissible. 2. Leakage is caused by dirty or scored key or body. Leakage due to dirt is corrected by cleaning parts and applying a thin coating of cup grease on the key. Leakage due to a scored key or body cannot be repaired, and the drain cock must be replaced.
Testing
1. LEAKAGE TESTS. With the air brake system charged, coat the outside of the reser voir with soapsuds to check for leakage. If any leakage is found, replace the reservoir. Z. INSPECTION. Inspect inside and out side surfaces for damage or corrosion. A small flashlight is helpful when inspecting the interior. If damage or corrosion is found that would weaken the reservoir, replace the reser voir. 3. Moisture taken in with the air through the compressor inlet valves collects in the reservoirs and necessitates draining the res ervoirs daily in cold weather and every week in warm weatherby opening the drain cock located on the bottom. Be sure to close the drain cocks after all moisture has been removed.
HOSE, HOSE ASSEMBLIES AND

HOSE CONNECTORS
Description
Hose and hose fittings provide a means of making flexible air connections between points on a vehicle which normally change their position in relation to each other, also of mak ing flexible connections between two vehicles. All hose assemblies include detachable - type hose connectors with spring guards. Hose assemblies used to connect the air brake sys tem to another vehicle are fitted with hose couplings. The two hose lines or hose cou plings at the rear of the tractor truck are marked by tags identifying them as "SERVICE" or IlEMERGENCY."
Testing
1. If any evidence is found indicating that a hose line is restricted, remove and blow air through it in both directions to be sure the passage through the hose is not obstructed in any way.
Fig. 18 - 111ustrates Reservoir, and Drain Cock.

DRAIN COCKS
Safety Valve,
Description
1. Drain cocks have a brass body fitted with a tapered brass key. The drain cock is open when the handle is parallel to the body, and closed when the handle is at right angles to the body. Drain cocks are installed in the bot tom of each reservoir in the air brake system to provide a convenient means of draining the condensation which normally collects in the reservoirs.
PRINTED IN UNITED STATES OF" AMERICA
2. With the brakes applied to be sure that the hose line being tested is under pressure, coat the outside of the hose and connections with soapsuds to check for leakage. No leakage is permissible. Leakage at the connectors is sometimes corrected by tightening the con nector nut. If this fails to correct the leakage, replace the connectors, hose, or both.
Replacement
Hose assemblies are easily replaceable by removing the detachable connectors and installing a new piece of hose. 1. Remove connector nuts, and pull hose out of connector body.
2. Do not attempt to remove used sleeve from hose. 3. Cut a piece of new hose to required length, being sure that cut is made at right angles to outside wall of hose, and that end of hose is smooth. 4. Blowout hose with an air line to re move all cuttings.
BLUNT
NOSED
SCREWDRIVER
ij-"fi"tJ"'"
).,:
_.---.
SLEEVE NUT
Fig. 21
7. Push gasket into bottom of recess in connector body (Fig. 21).
Fig. 19
5. Place connector nut and sleeve on hose (Fig. 19), being sure that barbs on inside of sleeve point toward end of hose that is being connected.
CONNECTOR
80DY
NUT
SLEEVE
HOSE
GUIDE
800'1'
Fig. 22
8. Put end of hose in connector body, making sure that end of hose is against gasket at bottom of the recess (Fig. 22).
\
9. Move sleeve, if necessary, until it is against edge of connector body. Tighten con necting nut. It is only necessary to tighten nut sufficiently to insure an air-tight joint.
A9363
Fig. 20
6. Place new gasket over end of guide in connector body so that side with removable protector covering is next to hose. Remove protector >c.overing from gasket (Fig. 40).
10. When installing a hose assembly where both ends are permanently connected, the hose connector at either end is used as a swivel by loosening the nut on one of the connectors. Turn the hose in the loose connector before the connector nut is again tightened. This permits the installation of the hose without kinking or twisting.

HOSE. COUPLINGS AND DUMMY
COUPLINGS
Description
1. Hose couplings provide an easy and convenient :method of connecting and disconnect ing air lines between vehicles by hand. The design of the hose couplings is such that when two of the:m are coupled together pres.5ure is put on two rubber gaskets, :making an air-tight seal. 2. Du:m:my couplings are :made in two general designs, so:mebeing fittedwithbrackets to per:mit the:m to be rigidly :mounted on the vehicle, while others are fitted with a chain attaching the:m to the vehicle. The bracket type is used where the du:m:my coupling is to serve as a fastening for holding hose lines when not in use, whereas the chain type is used for blocking off hose couplings rigidly :mounted on the vehicle as used on the tractor truck. The purpose of the du:m:my coupling is to prevent the entrance of dirt or other foreign :matter into the air brake lines when the lines are not being used.
4. To install a new gasket, partially col lapse it with the fingers (Fig. 23), and enter one side of the gasket flan,ge in the groove in the coupling.
Testing
A1'362
1. With the hose couplings connected and brakes applied, coat the hose couplings all over with soapsuds to check for leakage. There :must be no leakage. 2. Leakage is usually caused by worn, da:maged, or i:mproperly installed gaskets. To correct leakage, install new gaskets. 3. Re:move old gasket by prying out with a screwdriver. Before atte:mpting to install a new gasket, be sure the groove in the coupling in which the gasket fits is thoroughly cleaned. Otherwise it will be i:mpossible to install a new gasket properly.
Fig. 2q
5. Then use a blunt nosed screwdriver or si:milar instru:ment to push the gasket into place (Fig. 24). When properly installed, the exposed face of the gasket will be flat, not twisted or bulged at any point.
TUBING
Operating Tests
(.
If any evidence is found that a tubing line is restricted, re:move and blow air through it in both directions to be sure the passage through the tubing is not obstructed in any way. Inspect tubing for partial restrictions such as :may be caused by dents or kinks. Da:maged tubing :must be replaced.
HOSE C01JPlING--";::::;;;;';
Leakage Tests
Fig. 23
PRINTED IN UNITED STATEl;S 0" AMERICA
With the air brake syste:m fully charged, the governor cut out, and brakes applied, coat all tubing lines and fittings with soapsuds to check for leakage. No leakage is per:missible. Leakage at a tubing fitting is so:meti:mes cor rected by tightening the tubing fitting nut. If this fails to correct the leakage, replace the tubing fitting, the tubing, or both.
, BRAKES ADJUSTMENTS Section D Page 1
HYDRAULIC BRAKES BRAKE SHOE ADJUSTMENTS AND SERVICING
lZXl-3/4 11 L-IIO, L-lll, L-IIZ { lZxl-3/4 11
FRONT REAR FRONT REAR
L -IZO , L-IZI , L-IZZ {lZXl-3/4 lZxZ If
11
Brake
lhoe
cup
Hold.doWll
spring aruI
cup
Brakelhoe
lining
A~2940
Fig. I - (Front) External View.
AdjU$ting screw
Adjusting screw
spring
A-22938
Fig. 2 - (Front) Internal View.
shoe web
Star wheel adjusting

A.22783
Fig. 3 - (Rear) External View.

PRINTEO IN UNITEO !$TATES OF AMERICA
Fig.
- (Rear) Internal View.
BRAKES- . ADJUSTMENTS Section D Page 2

Brake
lever end. With parking brake lever applied approximately I" from fully released pos ition, pull cables by hand to remove all slack. Adjust cables as required at yoke ends so that clevis pins can be in serted. Insert clevis pins and new cotter pins. 7. Back off star wheel adjusting screw 12 to 14 notches and then check to see that brake drum turns freely. It may be necessary to tap the backing plate lightly to permit the brake shoes to take a central position. 8. Rear brakes only. Pull parking brake lever back until the rear wheel can just be turned by hand. Check rear wheels for even brake drag. If drag is uneven, loosen the tight brake to provide even drag. 9. Replace adjusting hole covers.
Adjultmg
Major Adjustments and Servicing (Figs. 1, 2, 3, 4 and 5).

A.22939
Fig. 5
The following adjustments are performed only when adjustments under "Minor Adjustments" fail to give satisfactory results or when install ing new shoes or linings. NOTE: Perform Operations in Se uence Given. At both front and rear brakes unless otherwise noted.)
BRAKE ADJUSTMENT INSTRUCTIONS

Before attempting to make a,.ny brake adjust ments - whether minor or major - be sure that wheel bearings are properly adjusted and that brake backing plates are tight.
Adjustment For Wear (Minor)

(Figs. 1, 2, 3, 4 and 5)
NOTE: Perform Operations in Sequence Given At Both Front and Rear Brakes Unless Other wise Noted. ~
1. Place parking brake lever in fully released position.

2. Jack up truck until wheels are free from floor. 3. Remove wheels, hubs and drums. 4. Remove adjusting hole coyers. 5. Remove brake shoes and inspect linings for excessive wear, grease, loose rivets or other damage. Install new lining if old lining shows excessive wear or is saturated with grease or brake fluid. 6. Inspect brake drums for scores, run-out or
cracks. If scores are not too deep or "run
out" does not exceed .010", drums may be
machined. If drums are badly scored or
cracked, they should be replaced.
7. Inspect wheel cylinders for signs of fluid leakage or deteriorated rubber dust boots. If brake fluid is leaking out of wheel cylin ders, replace or recondition wheel cylinders. 8. Clean grease and dirt off backing plate and sand down shoe ledges if rusted or ridged.
1. Place parking brake lever in fully re leased position.

2. Jack up truck until the wheels are free from floor. 3. Remove adjusting hole covers.
4. Insert screwdriver or special adjusting tool in slot of backing plate to engage star wheel adjusting screw (Fig. 5). 5. Move outer end of screwdriver or special tool toward axle, expanding brake shoes to the point where the wheel can just be turned by hand. 6. Rear brakes only. NOTE: Parking brake c able adjustment should be made at this time. With brake shoes still expanded, disconnect the parking brake cable at the intermediate

9. Disconnect parking brake cables to rear brakes at intermediate lever end. Wipe off dirt and grease from exposed portion of cables and pull cables through con duits as far as possible from the brake end and wipe off old grease. 10. Apply a generous coating of cable lubricant to cables and slide cables back through con duits. Wipe off excessive grease from back plate. 11. Apply a thin coating of suitable lubricant comparable to "Lubriplate" to shoe ledges and on rear brakes apply to the parking brake lever fulcrum and strut contact points. lZ. Thoroughly clean star wheel adjusting screws, pivot nuts, hold down pins, springs and cups. Apply a small amount of suitable lubricant comparable to "Lubriplate" to the threaded end of the adjusting screw and to contact points on the shoe webs. 13. When installing new shoes, lay the shoes out in pairs according to their position on the truck. The rear (secondary) shoe is the shoe with lining. 14. Rear brakes only. On rear brake shoes attach parking brake levers to backing plate side of shoe web, using lever pin, spring and retainer. Squeeze ends of retainer lock together after assembly of retainer. 15. Thread the star wheel adjusting screw into the pivot nut to the limit of the thread and assemble star wheel adjusting screw and adjusting screw spring to the adjustment end of the shoes with pivot nut against the right hand shoe. NOTE: Always assemble pivot nut on the right hand shoe regardless of position of shoes on the truck. 16. Guide forked end of shoe links over anchor end of shoe web, and attach shoes to backing plates by means of shoe hold down pins, springs and cups. 17. On rear brakes only, assemble spring on strut against strut shoulder and assemble strut between front (primary) shoe and parking brake lever. The small loop of spring rests against inside of shoe web on right hand brake and on outside of shoe web on left hand brake. 18. On rear brakes only, attach cable to parking brake lever by compressing cable retracting spring and sliding cable into loop at end of lever. 19. Attach retracting springs to shoes and anchor pins. If springs show signs of hav ing been overstressed, they should be re placed.
PRINTED IN UNITED STATES Of!' AMERICA
BRAKES ADJUSTMENTS Section D Page 3
ZO, Install brake drums ...(For lubrication and adjustment of front wheel bearings see Wheel Section",) NOTE: DO NOT LOOSEN ANCHOR PlNS UNLESS INSPECTION OF LINING-TO-DRUM CLEARANCE INDICATES A NEED FOR REPOSITIONING OF ANCHORS. Zl. Insert a .015" feeler gauge between the lining and drum of the rear (secondary) shoe about l-l/Z" from thEt. star wheel ad justing screw end of the shoe and expand shoe by turning star wheel adjusting screw until feeler gauge cannot be withdrawn. Then turn star wheel adjusting screw in opposite direction until there is but a light drag on the feeler gauge. Withdraw feeler g~uge. NOTE: Expanding shoes until feeler gauge cannot be with drawn insures that shoes are resting against the anchor pin. ZZ. Revolve brake drum so that feeler gauge hole is about l-l/Z" from the anchor end of the rear (secondary) shoe lining. There should be a slightly heavier drag on the feeler gauge at this point. If the clearance at the anchor end of the shoe is greater than the clear ance at the adjustment end by .003" or more, it will be necessary to adjust the anchor pin. Z3. To adjust anchor pin, loosen locknut 1/4 to liZ of a turn and tap anchor pin either up or down to provide the correct anchor pin position. After positioning the anchor pin to provide the correct rear (secondary) shoe clearance, tighten the anchor pin locknut with a 16" wrench and then re :::heck anchor and adjusting end clearances. NOTE: If anchor pin nut is loosened too much, the anchor pin may shift when tighten ing the locknut, Z4. To adjust rear parking brake cables expand shoes at both rear brakes until tight against brake drums. With parking brake lever applied approximately I" from fully released positio!l, pull cables by hand to remove all slack. Adjust cables as required at yoke ends so that clevis pins can be inserted. Insert clevis pins and new cotter pins. Z5. At both rear brakes back off star wheel adjusting screw lZ to 14 notches. Z6. To check rear brakes for balance, pull parking brake lever back until rear wheels can just be turned by hand. Check rear wheels for even brake drag. If drag is uneven, loosen the tight brake to provide even drag. Z7. Replace adjusting hole covers.
BRAKES ADJUSTMENTS Section E Page 1
12 X 1-3/4 11 LM-120, LM-121, LM-122 { 12 x 2"
FRONT REAR
Brake
Ihoe
cup
Hold-down
spring and
cup
Brake shoe
lining
Fig. t - (Front) External View.
Adjusting screw
Adjusting screw spring
A2293B
Fig. 2 - (Fronf) Internal View.
Wheel cylinder Anchor pin
Anchor pin ke shoe web
Star wheel adjusting screw

A-22926
Adjusting screw spring

A-22927.

PRINTED IN UNITED STATES OF
AM~ICA
Fig.
- (Rear) Internal View.

6. Back off star wheel adjusting screw 12 to 14 notches and then check to see that brake drum turns freely. It may be necessary to tap the backing plate lightly to permit the brake shoes to take a central position. 7. Replace adjusting hole covers.
Adjustiug
Major Adjustments and Servicing

(Figs. 1, 2, 3, 4 and 5).
The following adjustments are performed only when adjustments under "Minor Adjustments" fail to give satisfactory results or when in stalling new shoes or linings. NOTE: PERFORM OPERATIONS IN SE QUENCE GIVEN (AT BOTH FRONT AND REAR BRAKES UNLESS OTHER WISE NOTED):

A-22939
Fig. 5
2. Jack up truck until wheels are free from floor. 3. Remove wheels, hubs and drums.

Before attempting to make any brake adjustments whether minor or major, be sure that wheel bear ings are properly adjusted and that brake backing plates are tight.
4. Remove adjusting hole covers. 5. Remove brake shoes and inspect linings for excessive wear, grease, loose rivets or other damage. Install new lining if old lining shows excessive wear or is saturated with grease or brake fluid. 6. Inspect brake drums for scores, run-out or cracks. If scores are not too deep or "run out" does not exceed .010", drums may be machined. If drums are badly scored or cracked, they should be replaced. 7. Inspect wheel cylinders for signs of fluid leakage or deteriorated rubber dust boots. If brake fluid is leaking out of wheel cylinder s, replace or recondition wheel cylinders. 8. Clean grease and dirt off backing place and sand down shoe ledges if rusted or ridged. 9. Apply a thin coating of suitable lubricant comparable to "Lubriplate" to shoe ledges. 10. Thoroughly clean star wheel adjusting screws, pivot nuts, hold down pins, springs and cups. Apply a small amount of suitable lubricant comparable to ,oLubriplate" to the threaded end of the adjusting screw and to contact points on the shoe webs.

NOTE: PERFORM OPERATIONS IN SE QUENCE GIVEN (AT BOTH FRONT AND REAR BRAKES UNLESS OTHER WISE NOTED):
1. Place parking brake lever in fully released position. 2. Jack up truck until the wheels are free from floor. 3. Remove adjusting hole covers. 4. Insert screwdriver or special adjusting tool in slot of backing plate to engage star wheel adjusting screw (Fig. 5). 5. Move outer end of screwdriver or special tool toward axle, expanding brake shoes to the point where the wheel can just be turned by hand.
L~LINE
11. When installing new shoes, lay the shoes out in pairs according to their position on the truck. The rear (secondary) shoe is the shoe with longer lining. lZ. Thread the star wheel adjusting screw into the pivot nut to the limit of the thread and assembly star wheel adjusting screw and adjusting screw spring to the adjustment end of the shoes with pivot nut against the right hand shoe. NOTE: Always assemble pivot nut on the right hand shoe regardless of position of shoes on the truck. 13. Guide forked end of shoe links over anchor end of shoe web, and attach shoes to backing plates by means of shoe hold down pins, springs and cups. 14. Attach retracting springs to shoe and anchor pins. If springs show signs of having been overstressed, they should be replaced. 15. Install brake drums. (For lubrication and adjustment of front wheel bearings see Whe e1 Section.) NOTE: DO NOT LOOSEN ANCHOR PINS UNLESS INSPECTION OF LINING TO DRUM CLEARANCE INDICATES A NEED FOR REPOSITIONING OF ANCHORS.
NOTE: If anchor pin nut is loosened too much, the anchor pin may shift when tightening the locknut. 19. Replace adjusting hole covers.
16. Insert a .015" feeler gauge between the lining and drum of the rear (secondary) shoe about l-l/Z" from"the star wheel ad justing screw end of the shoe and expand shoe by turning star wheel adjusting screw until feeler gauge cannot be withdrawn. Then turn star wheel adjusting screw in opposite direction until there is but a light drag on the feeler gauge. Withdraw feeler gauge. NOTE: Expanding shoes until feeler gauge cannot be with drawn insures that shoes are resting against the anchor pin. 17. Revolve brake drum so that feeler gauge hole is about l-l/Z" from the anchor end of the rear (secondary) shoe lining. There should be a slightly heavier drag on the feeler gauge at this point. If the clearance at the anchor end of the shoe is greater than the clearance at the adjustment end by .003" or more, it will be necessary to ad just the anchor pin. 18. To adjust anchor pin, loosen locknut 1/4 to liz turn and tap anchor pin either up or down to provide the correct anchor pin position. After positioning the anchor pin to provide the correct rear (secondary) shoe clearance, tighten the anchor pin lock nut with a 16" wrench and then recheck an c h 0 r an d adjusting en d clearances.
P'UNTD 'N UNITED STATES
or
AMERICA
BRAKES ADJUSTMENTS Section F Page 1
12 X 1-3/4" L-130, L-131, L-132 { 14 x 2-1/411
FRONT REAR
Brake shoe
Hold-down spring ami rup Brake shoe
lining
Adjll$Ung screw
Adjusting screw
spring
11-22938
Brake .hoe hoJd-down spring and
'Adjusting hole cover

A-230S5
Star
screw
A23054

PRINTED IN UNITED STATES 0" AMEI'HCA
Fig.
ij
(Rear) Internal View.

6. Back off adjusting screw 12 to 14 notches
and then check to see that brake drum turns freely. It may be necessary to tap the back ing plate lightly to permit the brake shoes to take a central position. 7. Replace adjusting hole c;:)Vers.
Major Adjustments and Servicing

(Figs. 1, 2, 3, 4, 5).
Adjusting .
The following adjustments are performed only when adjustments under "Minor Adjustments..... fail to give satisfactory results or when in stalling new shoe s or linings. NOTE: PERFORM OPERATIONS IN SEQ U E N C E G I V E NAT BOTH FRONT AND REAR BRAKES UN LESS OTHERWISE NOTED):
1. Place parking brake lever in fully released position. 2. Jack up truck until wheels are free from floor. 3. Remove wheels, hubs, and drums.
A-22939
4. Remove adjusting hole covers.
Fig. 5
5. Remove brake shoes and inspect linings for excessive wear, grease, loose rivets or other damage. Install new lining if old shows excessive wear or is saturated with grease or brake fluid.

Before attempting to make any brake adjust ments, whether minor or major, be sure that wheel bearings are properly adjusted and that brake backing plates are tight.
6. Inspect brake drums .for scores, run-out

or cracks. If scores are not too deep or "run-out" does not exceed ,010", drums may be machined. If drums are badly scored or cracked. they should be replaced. 7. Inspect wheel cylinders for signs of fluid leakage or deteriorated rubber dust boots. If brake fluid is leaking out of wheel cylin ders, replace or recondition wheel cylinders. 8. Clean grease and dirt off of backing plate and sand down shoe ledges o.f rusted or ridged. 9. Apply a thin coating of suitable lubricant comparable to "Lubriplate" to shoe ledges. 10, Thoroughly clean star wheel adjusting screws, pivot nuts, hold down pins, springs and cups, Apply a small amount of suitable lubricant comparable to "Lubriplate" to the threaded end of the adjusting sc rew and to contact points on the shoe webs. 11. When installing new shoes, lay the shoes out in pairs according to their position on the truck, The rear (secondary) shoe is the shoe with longer lining.
Adjustment for Wear (Minor)

NOTE: PERFORM OPERATIONS IN SEQ U ENe E G I V E NAT BOTH FRONT AND REAR BRAKES UN LESS OTHERWISE NOTED):
1. Place parking brake lever in fully released position. 2. Jack up truck until the wheels are free from floor. 3. Remove adjusting hole covers. 4. Insert screw driver or special adjusting tool in slot of backing plate to engage star wheel adjusting screw (Fig. 5). 5. Move outer end of screw driver or special tool toward axle, expanding brake shoes to the point where the wheel can just be turned by hand.

lZ. Thread the star wheel adjusting screw into
the pivot nut to the lixnit of the thread and
assexnble star wheel adjusting screw and
adjusting screw spring to the adjustxnent
end of the shoes with pivot nut against the
right hand shoe. NOTE: Always assexnble
pivot nut on the right hand shoe regardless
of position of shoes on the truck.
13. Guide forked end of shoe links over anchor
end of shoe web, and attach shoes to backing
plates by xneans of shoe hold down pins,
springs and cups.
14. Attach retracting springs to shoes and
anchor pins. If springs show signs of having
been overstressed, they should be replaced.
15. Install brake druxns. (For lubrication and
adjustxnent of front wheel bearings see
Wheel Se ction.)
NOTE: DO NOT LOOSEN ANCHOR PINS
UNLESS INSPECTION OF LINING
TO DRUM CLEARANCE INDICATES
A NEED FOR REPOSITIONING OF
ANCHORS.
16. Insert a .015" feeler gauge between the

lining and druxn of the rear (secondary)
shoe about l-l/Z" froxn the star wheel
adjusting screw end of the shoe and expand
shoe by turning star wheel adjusting screw
until feeler gauge cannot be withdrawn.
Then turn star wheel adjusting screw in
opposite direction until there is but a light
drag on the feeler gauge. Withdraw feeler
gauge. NOT E: Expanding shoes until
feeler gauge cannot be withdrawn insures
that shoes are resting against the anchor
pin.
17. Revolve brake druxn so that feeler gauge hole is about l-l/Z" froxn the anchor end of the rear (secondary) shoe lining. There should be a slightly heavier drag on the feeler gauge at this point. If the clearance at the anchor end of the shoe is greater than the clearance at the adjustxnent end by .003" or xnore, it will be necessary to ad
just the anchor pin.
18. To adjust anchor pin, loosen locknut 1/4 to liZ turn and tap anchor pin either up or down to provide the correct anchor pin position. After positioning the anchor pin to provide the correct rear (secondary) shoe clearance, tighten the anchor pin lock nut with a 16" wrench and then recheck anchor and adjusting end clearances. NOTE: If anchor pin nut is loosened too xnuch, the anchor pin xnay shift when tightening the locknut. 19. Replace adjusting hole covers.
PRJl'iTEO IN UNITED STATES OF' AMERICA
BRAKES ADJUSTMENTS Section G Page 1
12 X 1-3/411 LB-140 { 14 x 2-1/4"
FRONT REAR
pring and cup
Brake .hoe
Hold-down .prinr ad
cup
Brake .hoe
lining
Adjusting
screw
Adjutlmg
lcreW
IJIring
Fig. 2 -
(Front~
Internal View.
Wheel cylinder Connecting link _----..l Retracting Brake shoe hold.down
screw
A2306S

PRINTED IN UNITED STATES Of' AMERICA
Fig.
- {Rear} Internal View.

intermediate lever end. With parking brake lever applied approximately 1" from fully released position, pull cables by hand to re move all slack. Adjust cables as required at yoke end so that clevis pins can be inserted. Insert clevis pins and new cotter pins. 7. Back off star wheel adjusUng screw 12 to 14 notches and then check to see that brake drum turns freely. It may be necessary to tap the backing plate lightly to permit the brake shoes to take a central pos ition. 8, REAR BRAKES ONLY. Pull parking brake lever back until the rear wheel can just be turned by hand. Check rear wheels for even brake drag. If drag is uneven, loosen the tight brake to provide even drag. 9. Replace adjusting hole covers.
Adjusting
Major Adjustments and Servicing (Fig. 1, 2, 3, 4 and 5).

The following adjustments are performed only when adjustments under "Minor Adjustments" fail to give satisfactory results or when install ing new shoes or linings. NOTE:
Fi g. 5
PERFORM OPERA TrONS IN SE QUENCE GIVEN (AT BOTH FRONT AND REAR BRAKES UNLESS OTHER WISE NOTED):

Before attempting to make any brake adjust me,nts, whether minor or major, be sure that wheel bearings are properly adjusted and that brake backing plates are tight.

2. Jack up truck until wheels are free from floor. 3. Remove wheels, hubs and drums. 4. Remove adjusting hole covers. 5. Remove brake shoes and inspect linings for excessive wear, grease, loose rivets or other damage. Install new lining if old lining shows excessive wear or is saturated with grease or brake fluid. 6. Inspect brake drums for scores, run-out or cracks. If scores are not too deep .or "run-out" does not exceed .010", drums may be machined. If drums are badly scored or cracked, they should be replaced. 7. Inspect wheel cylinders for signs of fluid leakage or deteriorated rubber dust boots. If brake fluid is leaking out of wheel cylin ders, replace or recondition wheel cylinders. 8. Clean grease and dirt off of backing plate and sand down shoe ledges if rusted or ridged. 9. Disconnect parking brake cables to rear brakes at intermediate lever end. Wipe off dirt and grease from exposed portion of cables and pull cables through conduits as far as possible from the brake end and wipe off old grease.

1. Place parking brake lever in fully released

position. 2. Jack up truck until the wheels are free from floor.
3. Remove adjusting hole covers. 4. Insert screwdriver or special adjusting tool in slot of backi.ng plate to engage star wheel adjusting screw (Fig. 5). 5. Move outer end of screwdriver or special tool toward axle, expanding brake shoes to the point where the wheel can just be turned by hand. . 6, REAR BRAKES ONLY. NOTE: Parking brake cable adjustment should be made at this time. With brake shoes still expanded, disconnect the parking brake cable at the

10. Apply a generous coating of cable lubricant to cables and slide cables back through conduits. Wipe off excessive grease from backing plate. 11. Apply a thin coating of suitable lubricant comparable to "Lubriplate" to shoe ledges and on rear brakes apply to the parking brake lever fulcrum and strut contact points. 12. Thoroughly clean star wheel adjusting screws, pivot nuts, hold down pins, springs and cups. Apply a small amount of suitable lubricant comparable to "Lubriplate" to the threaded end of the adjusting screw and to contact points on the shoe webs. 13. When installing new shoes, lay the shoes out in pairs according to their position on the truck. The rear (secondary) shoe is the shoe with longer lining. 14. REAR BRAKES ONLY. On rear shoes at tach parking brake levers to backing plate side of shoe web. Place spring washer on parking brake lever pin and insert pin through lever and shoe from the backing plate side. Assemble lockwasher and nut. Adjust nut so that parking brake lever is under spring tension, but free of bind. 15. REAR BRAKES ONLY. Attach parking brake lever strut to parking brake lever from side opposite backing plate with conical spring, flat washer and cotter pin. 16. Thread the star wheel adjusting screw into the pivot nut to the limit of the thread and assemble star wheel adjusting screw and adjusting screw spring to the adjustment end of the shoes with pivot nut against the right hand shoe. NOTE: Always assemble pivot nut on the right hand shoe regardless of position of shoes on the truck. 17. FRONT BRAKES ONLY. Guide forked end of shoe links over anchor end of shoe web, and attach shoes to backing plates by means of shoe hold down pins, springs and cups. 18. REAR BRAKES ONLY. Place parking brake lever strut spring against shoulder at front (primary) shoe end of strut. Guide forked end of strut and shoe links over anchor end of shoe webs. Attach shoes to backing plate by means of shoe hold down pins, springs and cups. 19. REAR BRAKES ONLY. Attach cable to parking brake lever by sliding yoke at brake end of cable over hook end of packing brake lever. 20. Attach retracting springs to shoes and anchor pins. If springs show signs of having been overstressed, they should be replaced.
Pl'tINTEO IN UNtTD STATES 0'" A.MERICA
21. Install brake drums. (For lubrication and adjustment of front wheel bearings see Wheel Section.) NOTE: DO NOT LOOSEN ANCHOR PINS UNLESS INSPECTION OF LINING TO DRUM CLEARANCE INDICATES A NEED FOR REPOSITIONING OF ANCHORS.
22. Insert a .015" feeler gauge between the lining and drum of the rear (secondary) shoe about 1-1/2" from the star wheel ad justing screw e~d of the shoe and expand shoe by turning star wheel adjusting screw until feeler gauge cannot be withdrawn. Then turn star wheel adjusting screw in opposite direction until there is but a light drag on the feeler gauge. Withdraw feeler gauge. NOTE: Expanding shoes until feeler gauge cannot be with drawn insures that shoes are resting against the anchor pin. 23. Revolve brake drum so that feeler gauge hole is about 1-1/2" from the anchor end of the rear (secondary) shoe lining. There should be a slightly heavier drag on the feeler gauge at this point. If the clearance at the anchor end of the shoe is greater than the clearance at the adjustment end by .003" or more, it will be necessary to adjust the anchor pin. 24. To adjust anchor pin, loosen lock nut 1/4 to 1/2 turn and tap anchor pin either up or down to provide the correct anchor pin position. After positioning the anchor pin. to provide the correct rear (secondary) shoe clearance, tighten the anchor pin lock nut with a 16" wrench and then recheck anchor and adjusting end clearances. NOTE: If anchor pin nut is loosened too much, the anchor pin may shift when tighten ing the lock nut. 25. To adjust rear parking brake cables ex pand shoes at both rear brakes until tight against brake drums. With parking brake lever applied approximately 1" from fully released position, pull cables by hand to remove all slack. Adjust cables as re quired at yoke ends so that clevis pin can be inserted. Insert clevis pins and new cotter pins. 26. At both rear brakes back off star wheel adjusting screw 12 to 14 notches. 27. To check rear brakes for balance, pull park ing brake lever back until rear wheel can just be turned by hand. Check rear wheels for even brake drag. If drag is uneven, loosen the tight brake to provide even drag. 28. Replace adjusting hole covers.
BRAKES ADJUSTMENTS Section H Page 1
12-1/8 X 2" L-150, LM-150, LM-151 { 14 x 2-1/4"
FRONT REAR
Fig, I - (Front) External View.
valve
Brake .hoe hold-down spring and
:t\U,Iuslmg hole cover

A23055
Star
adjusting screw
'A liind"'" screw spring A.23054

PRINTED IN UNITED STATES OF AMlf:fiICA.
Fig.
Ij. -
(Rear) Internal View.

6. Move outer end' of screwdriver or special tool toward axle, expanding brake shoes to the point where the wheel can just be turned by hand. 7. Back off star wheel adjusting screw 12 to 14 notches and then check to see that brake drum turns freely. On rear brakes it may be necessary to tap the backing plate lightly to permit the brake shoes to take a central position.
BackiDg
plate,
Adjusting
8. Replace adjusting hole covers.

The following adjustments are performed only when adjustments under "Minor Adjustments" fail to give satisfactory results or when in stalling new shoes or linings. NOTE:
A-22939
Fig. 5
PERFORM OPERATIONS IN SE QuENcE GIVEN (AT BOTH FRONT AND REAR BRAKES UNLESS OTHER WISE NOTED):

1. Place parking brake lever in fully released position. 2. Jack up truck until wheels are free from floor. 3. Remove wheels, hubs and drums. 4. Remove adjusting hole covers. 5. Remove brake shoes and inspect linings for excessive wear, grease, loose rivets or other damage. Install new lining if old lining shows excessive wear or is saturated with grease or brake fluid. 6. Inspect brake drums for scores, run-out or cracks. If scores are not too deep or "run-out" does not exceed .010", drums may be machined. If drums are badly scored or cracked, they should be replaced. 7. Inspect wheel cylinders for signs of fluid leakage or deteriorated rubber dust boots. If brake fluid is leaking out of wheel cylin ders, replace or recondition wheel cylinders. 8. Clean grease and dirt off of backing plate and sand down shoe ledges if rusted or ridged. 9. Apply a thin coating of suitable lubricant comparable to "Lubriplate" to all shoe ledge s.

NOTE: PERFORM OPERATIONS IN SE QUENCE GIVEN (A T BOTH FRONT AND REAR BRAKES UNLESS OTHER WISE NOTED):
1. Place parking brake lever in fully released position. 2. Jack up truck until the wheels are free from floor. 3. Remove adjusting hole covers. 4. On front brakes only loosen eccentric lock nut and turn eccentric adjustment in the direction of forward wheel rotation until upper (secondary) brake shoe drags. Then turn eccentric in opposite direction until upper (secondary) brake shoe is free of drag. Hold eccentric and tighten eccentric locknut. 5. Insert screwdriver or special adjusting tool in slot of backing plate to engage star wheel adjusting screw (Fig. 5).
L~LINE
10. Thoroughly clean star wheel adjusting screws, pivot nuts, hold down pins, springs and cups. Apply a small amount of suitable lubricant comparable to "Lubriplate" to the threaded end of the adjusting screw and to contact points on the shoe webs.
NOTE: PERFORM THE FOLLOWING OPER ATIONS AT EACH FRONT WHEEL (SEE FIGS. 1 AND 2):
19. To adjust anchor pin loosen locknut 1/4 to 1/2 turn and tap anchor pin toward the front
or rear of truck to provide the correct clearance. When the desired lining to drum clearance is obtained, tighten anchor pin nut with a 16" wrench and then recheck (secondary) shoe clearances. NOTE: 1 anchor pin nut is loosened too much, the anchor pin may shift when tightening the locknut. 20. Expand brake shoes by tightening star wheel adjusting screw to the point where wheel can just be turned by hand and then back off star wheel adjusting screw 1,,2 to 14 notches. Replace adjusting hole covers. NOTE: PERFORM THE FOLLOWING OPER ATIONS AT EACH REAR WHEEL (SEE FIGS. 2 AND 3):
11. When installing new brake shoes, lay the

shoes out in pairs according to their position on the truck. The upper (secondary) shoe is the shoe with the longer lining.
12. Thread the star wheel adjusting screw into the pivot nut to the limit of the threads and as semble star wheel adjusting screw and spring to the adjustment end of the shoes. NOTE: Always assemble pivot nut on the right hand shoe as viewed from the ad justing screw end of the shoes regardless of whether the brake shoes are for left or right side of truck.
13. Assemble shoe links to wheel cylinder and and guide forked end of shoe links over anchor end of shoe webs.
21. When installing new shoes, lay the shoes out in pairs according to their position on truck, The rear (secondary) shoe is the shoe with longer lining.
22. Thread the star wheel adjusting screw into

the pivot nut to the limit of the thread and assemble star wheel adjusting screw and adjusting screw spring to the adjustment and of the shoes with pivot nut against the right hand shoe. NOTE: Always assemble pivot nut on the right hand shoe regardless of position of shoes on the truck. 23. Guide forked end of shoe links over anchor end of shoe web, and attach shoes to backing plates by means of shoe hold down pins" springs and cups.
14. Attach brake shoes to backing plates with shoe hold down pins, springs and cups.
15. Attach retracting springs to shoes and anchor pin. 1 springs show signs of having
been overstressed, they should be replaced.
16. Install brake drums. (For lubrication and

adjustment of front wheel bearings see wheel section). NOTE: It may be nec essary to change the position of the shoe eccentric when assembling drum over shoes. NOTE: DO NOT LOOSEN ANCHOR PINS UNLESS INSPECTION OF LINING TO DRUM CLEARANCE INDICATES A NEED FOR REPOSITIONING OF ANCHORS.
24. Attach retracting springs to shoes and anchor pin. If springs show signs of having been
overstressed, they should be replaced.
25. Install brake drums.

NOTE: DO NOT LOOSEN ANC HOR PINS UNLESS INSPECTION OF LINING TO DRUM CLEARANCE INDICATES A NEED FOR REPOSITIONING OF ANCHORS.
17. Loosen eccentric adjustment locknut and

turn eccentric adjustment in the direction of forward wheel rotation until the upper (secondary) shoe begins to drag. Then turn eccentric in opposite direction until brake is just free of drag. Hold eccentric and tighten eccentric locknut.
26. Insert a .015" feeler gauge between the

lining and drum of the rear (secondary) shoe about 1-1/2" from the star wheel ad justing screw end of the shoe and expand shoe by turning star wheel adjusting screw until feeler gauge cannot be withdrawn. Then turn star wheel adjusting screw in opposite direction until there is but a light drag on the feeler gauge. Withdraw feeler gauge. NOTE: Expanding shoes until feeler gauge cannot be withdrawn insures that shoes are resting against the anchor pin.
18. Check lining to drum clearance at both

ends of the upper (secondary) shoe. The clearance at both ends of the upper (second ary shoe should be .010". 1 the clearance at the anchor end of the shoe is greater than the clearance at the adjustment end by .003" or more, it will then be necessary to adjust the anchor pin.
PRINTED IN UNITED STATES OF AMER1CA
27. Revolve brake drum so that feeler gauge hole is about 1-1/2" from the anchor end of the rear (secondary) shoe lining. There should be a slightly heavier drag on the feeler gauge at this point. If the clear"ance at the anchor end of the shoe is greater than the clearance at the adjustment end by .003" or more, it will be necessary to adjust the anchor pin. 28. To adjust anchor pin, loosen locknut 1/4 to 1/2 turn and tap anchor pin either up or down to provide the correct anchor pin position. After positioning the anchor pin to provide the correct rear (secondary) shoe clearance, tighten the anchor pin lock nut with a 16" wrench and then recheck anchor and adjusting end clearances. NOTE: If anchor pin is loosened too much, the anchor pin may shift when tightening the locknut. 29. Replace adjusting hole covers.
BRAKES ADJUSTMENTS Section I Page 1
12-1/8 x 2" FRONT L-lSl, L-lS2, L-153, LM-lS2 { 14-1/8 x 3" REAR

PRINTED IN UNITED ,,"AT5 OF A "'1 ERICA
Fig. q - (Rear) Internal View.

5. Insert screwdriver or special adjusting tool in slot of backing plate to engage star wheel adjusting screw (Fig. 5).
6. Move outer end of screwdriver or special

toward axle, expanding brake shoes to the point where the wheel can just be turned by hand. 7. Back off star wheel adjusting screw 12 to 14 notches and then check to see that brake drum turns freely. 8. Replace adjusting hole covers. NOTE: PERFORM THE FOLLOWING AT EACH REAR WHEEL (SEE FIGS. 3 AND 4):
Adjustmr
9. Insert screwdriver or special adjusting tool

into upper or front shoe adjusting screw slot of backing plate to engage star wheel adjusting screw (Fig. 5),
10. Move outer end of screwdriver or special adjusting tool toward axle, expanding front brake shoe to the point where the wheel can just be turned-by hand.
A.2.2939
Fig. 5
11. Back off star wheel adjusting screw until brake drum is just free of brake drag, approximately 6 notches, 12. Insert screwdriver or special adjusting tool into lower or rear shoe adjusting screw slot of backing plate and expand rear brake shoe to the point where the wheel can just be turned by hand.

Adjustments For Wear (Minor)

13. Back off star wheel adjusting screw until brake drum is just free of brake drag, approximately 6 notches.
14. Replace adjusting hole covers,
1. Place parking brake lever in fully released position. 2. Jack up truck until the wheels are free from floor.
3. Remove adjusting hole covers.

The following adjustments are performed only when adjustments under "Minor Adjustments" fail to give satisfactory results or when in stalling new shoes or linings. NOTE: PERFORM OPERATIONS IN SE QUENCE GIVEN. (AT BOTH FRONT AND REAR BRAKES UNLESS OTHER WISE NOTED):
NOTE:
PERFORM THE FOLLOWING AT EACH FRONT WHEEL (SEE FIGS. 1 AND 2):
4. Loosen eccentric locknut and turn eccentric adjustment in the direction of forward wheel rotation until upper (secondary) brake shoe drags. Then turn eccentric in opposite direction until upper (secondary) brake shoe is free of drag. Hold eccentric and tighten eccentric locknut.
1. Place parking brake lever in fully released position. 2. Jack up truck until wheels are free from floor. 3. Remove wheels, hubs and drums,

4. Remove adjusting hole covers. 5. Remove brake shoes and inspect linings for excessive wear, grease, loose rivets or other damage. Ins tall new lining if old lining shows excessive wear or is saturated with grease or brake fluid. 6. Inspect brake drums for scores, run-out or cracks. If scores are not too deep or IIrun-out" does not e;)!:ceed .010", drums may be machined. If drums are badly scored or cracked, they should be re placed. 7. Inspect wheel cylinders for signs of fluid leakage or deteriorated rubber dust boots. If brake .fluid is leaking out o.f wheel cylinders, replace or recondition wheel cylinders. 8. Clean grease and dirt off of backing plate and sand down shoe ledges if rus ted or ridged. 9. Apply a thin coating of suitable lubricant comparable to "Lubriplate" to all shoe ledges. 10. Thoroughly clean star wheel adjusting screws, pivot nuts, hold down pins, springs and cups of front brakes and clean star wheel adjusting screws, locksprings, hold down nuts and washers of rear brakes. Apply a small amount of suitable lubricant comparable to "Lubriplate" to threaded end of the adjusting screws and to points of contact of the shoe webs with the shoe links and anchor buttons. NOTE: PERFORM THE FOLLOWING OPER ATIONS AT EACH FRONT WHEEL (SEE FIGS. 1 AND 2):
15. Attach retracting springs to shoes and anchor pin. If springs show signs of having been overstressed, they should be replaced. 16. Install brake drums. (For lubrication and adjustment of front wheel bearings see wheel section.) NOTE: It may be necessary to change the position of the shoe eccentric when as sembling drum over shoe s. NOTE: DO NOT LOOSEN ANC HOR PINS UNLESS INSPECTION OF LINING TO DR UM CLEARANCES INDICATE A NEED FOR REPOSITIONING OF ANCHORS.
17. Loosen eccentric adjustment locknut and turn eccentric adjustment in the direction of forward wheel rotation until the upper (seconda"l'Y) shoe begins to drag. Then turn eccentric in opposite direction until brake is just free of drag. Hold eccentric and tighten eccentric locknut. 18. Check lining to drum clearance at both ends of the upper (secondary) shoe. The clearance at both ends of the upper (second ary) shoe should be .010". If the clearance at the anchor end of the shoe is greater than the clearance at the adjustment end by .003" or more, it will then be necessary to adjust the anchor pin. 19. To adjust the anchor pin loosen locknut 1/4 to 1/2 turn and tap anchor pin toward the front or rear of truck to provide the correct clearance. When'the desired lining to drum clearance is obtained, tighten anchor pin nut with a 16" wrench and then recheck upper (secondary) shoe clearances. NOTE: If anchor pin nut is loosened too much, the anchor pin may shift when tightening the locknut. 20. Expand brake shoes by tightening star wheel adjusting screw to the point where wheel can just be turned by hand and then back off star wheel adjusting screw 12 to 14 notches. Replace adjusting hole covers. NOTE: PERFORM THE FOLLOWING OPER ATIONS AT EACH REAR WHEEL (SEE FIGS. 3 AND 4):
11. When installing new brake shoes, lay the shoes out in pairs according to their position on the truck. The upper (secondary) shoe is the shoe with the longer lining. 12. Thread the star wheel adjusting screw into the pivot nut to the limit of the threads and assemble star wheel adjusting screw and spring to the adjustment end of the shoes. NOTE: Always assemble pivot nut on the right hand shoe as viewed from the adjusting screw end of the shoes regardless of whether the brake shoes are for left or right s ide of truck. 13. Assemble shoe links to wheel cylinders and guide forked end of shoe links over anchor end of shoe webs. 14. Attach brake shoes to backing plate with shoe hold down pins, springs and cups.
PRlNTED IN UNITO STATES OF' AMERICA
21. Thread star wheel adjustment screws into anchor brackets to the limit of the thread and assemble 10cksprings over anchor brackets with long end of lockspring in contact with star wheel. 22. Assemble shoe links to wheel cylinders. 23. Hold anchor button in place against cut out of rear shoe web and guide anchor button into the notch of the anchor bracket. Guide forked end of shoe links over shoe web.
24. Apply a thin coating of suitable lubricant cOInparable to "Lubriplate" to one side of shoe hold down washer and asseInble this side of hold down washer against shoe web. Place a .006- feeler gauge between center shoe ledge and riIn of shoe, with shoe in place against the anchor bracket and ad justing screw pad asseInble hold down nut and draw down tight against washer, back off one castellation and insert cotter key. 25. Attach retracting springs (black spring) to brake shoe and anchor bracket and (yellow spring) to brake shoe and anchor bracket stud. 26. As seInble front shoe to backing plate in the saIne Inanner. 27. Install brake druIns. 28. To adjust front shoe insert screwdriver or special brake adjusting tool through slot in backing plate (upper front) and expand front brake shoe to the point where the wheel can just be turned by hand. 29. Back off star wheel adjusting screw 6 notches.
3D, To adjust rear shoe insert screwdriver or special brake ~djusting tool through slot in backing plate (lower rear) and expand rear brake shoe to the point where the wheel can
just be turned by hand.
31. Back off star wheel adjusting screw notches. 32. Replace, adjusting hole covers.
BRAKES ADJUSTMENTS Section J Page 1
L-160, L-161. L-162. L-163, L-164. L-165, }FRONT BRAKE LC-160, LC-161, LC-162. 12-1/811 x 2-1/411 L-170, L-l71. L-I72. L-l73, L-l74, L-175. (TYPE "F") LF-170, LF-171, LF-l72
L-180, L-181, L-182, L-183, L-184. L-185, }FRONT B/RAKE LC-180 LC-181 LC-182 13" x 2-1 4" , . (TYPE tlF")
L-190, L-191. L-192, L-193. L-194, L_195,}

LF-190, LF-191, LF-192, FRONT BRAKE
LC-190, LC-191, LC-192. IS" x 2-1/4"
L-200, L-201, L-202, L-204, L-205, (TYPE "F")
LC-200, LC-201, LC-202
Brake hose
Lining
___ r~n"<I'
shoe
Brake shoe cam adjustment (B)
Bleeder valve
A.231fT
Retracting spring
A2319B
Fig. I - Front Brake - Externa I View - Type "Ft!.

PRINTED IN UNtTEO STA.TES OF AMERICA
Fig. 2 - Front Brake _ Internal View -Type "F".
14
11 12
~J
, ,
'-
14
110
8
A-22913
7
Fig.3 - Front Brake -Exploded View-Type "F".
Item No.
1 2
DESCRIPTION
Item No.
DESCRIPTION
3 4 5
6
7 8 9 10 11 12 13 14 15
16
17 18
Plate assembly, brake backing. Stud, adjusting cam &. shoe guide. Washer, plain, cam stud. Spring, adjus ting cam. Cam, shoe adjus ting. Washer, spring, anti-rattle, shoe guide. Shoe &: lining assembly. Shoe. Lining. Rivet, lining. Washer, plain, shoe guide. Washer, "C", shoe guide stud. Spring, retracting, brake shoe. Wheel cylinder assembly. Body, wheel cylinder. Spring. Filler, piston cup. Cup, pis ton.
19 20 21
22 23
24
25
26
27 28
29
30
31 32
Piston assembly. Boot. Tube assembly, connector, wheel cylinder. Bolt, fitting, inlet, brake line to cylinder &: tube. Gasket, bolt. Fitting, inlet, fluid, connector tube. Gasket, fitting. Bolt, fitting, inlet, connector tube to cylinder. Screw, anchor, cylinder. Lockwasher, cylinder anchor screw. Washer, plain, cylinder anchor screw. Screw, fas tening, wheel cylinder. Lockwasher, fastening screw. Valve, bleeder, cylinder.

--Rotation
exerted against the drum and produces additional braking effect. Both shoes are forward acting (primary shoes), self-energizing in the forward direction of drum rotation, If the vehicle is moving' backward, the drag of the drum on the linings is in the opposite direction and produces "de-ener gization" which tends to move the shoe heels away from their anchor blocks. Piston forces at the shoe toes are large enough to overcome this action, but the shoes tend to rotate inwardly about their anchor points and att~mpt to leave the drum. Both shoes are reverse acting since neither is self-energized in the reverse direction of drum rotation. Cylinder anchor block sides are aligned on the axle radius. As the shoes roll upon their anchor blocks to contact the drum, the heels may also slide radially upon the anchor block surface. The shoes thus automatically flself-center fl in relation to the drum. The self-energization factor causes this brake to be approximately three times as effective during forward operation as it is during re verse operation; therefo.re its use is generally confined to the front axle of vehicles in con junction with a rear axle brake of a type pro viding effective stopping ability in reverse as well as forward motion.
Fig.
- Brake Adjustment, Type "F" Brake.
MAINTENANCE AND ADJUSTMENT

WAGNER SELF-CENTERING
TYPE "F" BRAKES
(See Figs. 1, 2 and 3)
This Wagner self-centering Hi-Tork Brake, Type "F", is a "Floating-Shoe" type which has two identical shoes (7), (Fig. 3) arranged on the backing plate (1) so that their toes are diagonally opposite, Two single-end wheel cylinders (14) are arranged so that one cylinder is mounted between each shoe toe and the op posite shoe heel. The two-wheel cylinder pistons (19) apply equal amounts of hydraulic force to each shoe toe. Each cylinder body is shaped to provide an anchor block for the opposite shoe heel. Each cylinder anchor block serves as a shoe stop and shoe centering point and provides the ful crum around which the shoe heel pivots when the brakes are applied. Each shoe is adjusted by means of an ec centric cam (5) which contacts the underside of the shoe table. Each cam is attached to the backing plate by a cam and shoe guide stud (2) which protrudes through a slot in its shoe web and, in conjunction with washers (11) and "c" washers (12), also serves as a shoe "hold-down". Two retracting springs (13) are connected be tween the shoes at each toe and heel, Upon brake application, the wheel cylinder pistons transmit pressure to the toes of the shoes, forcing the shoe linings into contact with the brake drum. If the vehicle is moving for ward, the drag of the drum against the shoe lining produces "self-energization" which tends to help rotate the shoes outwardly about their anchor points. This action multiplies the forces
PRINTED 11'< UNITED STATf,:S OF Ad"ERICA
Disassembly
Note A. The first disassembly operations is always removal of brake shoe re tracting springs (13). With brake spring pliers, pull one hooked end of spring free of shoe web.
Note B.
If wheel cylinder connector tubes (21) are removed, mark wheel cylinder ports to which tubes are attached to avoid error in re-assemb1y. Di ficulty will be encountered in bleeding operation if tubes are assembled in wrong location.
Step-By-step Procedure (Disassembly)

I. REMOVAL OF SHOE ASSEMBLIES:
1.
2.
Remove both brake shoe retracting springs (13). (Refer to Note A). Remove each shoe hold-down "c" washer (12) and washer (11), Shoes easily lift off.
II. REMOVAL OF WHEEL CLYINDERS: 1. 2. Remove brake shoe assemblies (7). Remove connector tubes (21) and wheel cylinder fittings (24). (Refer to Note B.)
BRAKES ADJUS TMENTS Section J Page 4

3. Place boot (20) on piston (19), making sure boot snaps over shoe guide. 4. Install piston and boot. Align piston shoe guide slot to accommodate the shoe toe. Push boot lip into place in groove machined on end of cylinder. V. REPLACEMENT OF WHEEL CYLINDERS:
3.
4.
Remove each cylinder anchor screw (27) (lar ge) and washer (29). Remove cylinder mounting screws (30) (small). Cylinders easily lift off.
III. WHEEL CYLINDER DISASSEMBLY:
1.
Pull boot (20) from wheel cylinder. Piston (19) should corne with boot. Pull boot from piston. Piston cup (18), cup filler (17), and spring (16) may be pulled from cylinder.
1. Place one cylinder in position on backing

plate. Install mounting screws (30) and lockwashers (31) (small). (Refer to Notes D and E). 2. Install cylinder anchor screw (27), washer (29), and lockwasher (28) (large).
2.
Assembly
Note C. Adjustment cam and shoe guide studs (2) are equipped with friction springs (4). They should easily turn with an 8" wrench, but should not be loose. If frozen, lubricate with kerosene or penetrating oil and work free. The two wheel cylinders mounted on one brake are identical; HOW EVER, CYLINDERS FOR LEFT OR RIGHT HAND BRAKES HAVE OP POSITE CASTINGS (15).
3. Repeat steps 1 and 2 for second cylinder. 4. Install wheel cylinder fittings (24) and tubes (21). (Refer to Note B under disassembly.) VI. REPLACEMENT OF SHOE ASSEMBLIES:
Note D.
1. Install sp-ring anti-rattle washer (6) on cam and shoe guide stud (2), pronged side facing adjusting cam (5). 2. Place shoe assembly on backing plate with cam and shoe guide stud protruding through shoe slot. Locate shoe toe in piston slot and shoe heel in anchor block slot. (Refer to Note G.)
Note E. Clean mating surfaces of cylinders and backing plate before assembly to insure proper alignment. Note F. When replacing shoe retracting springs (13), place spring end with long hook in heel. of shoe and then, with brake spring pliers, stretch spring to se cure short hook end in toe of opposite shoe. Use new springs if there is evidence of spring fatigue, (rust, set springs, etc.). Note G. For best results, new shoe and lining assemblies (7) should have linings (9) of correct thickness, ground (not buffed) to correct radius, concentric with the brake drum. If this is not done, readjustment may be required after linings ar e "worn-in I t . Do not lubricate brake mechanism except as noted in "C".
3. Replace hold down washer (11) and "c" washer (12) on cam and shoe guide stud. Crimp "c" washer on stud. 4. Repeat steps 1, 2, and 3 for second shoe. 5. Replace shoe retracting springs (l3).
(Refer to Note F).
Adju(stment
Lining to drum clearance adjustment is required when shoes are relined and, on occasion, to compensate for normal lining wear. Clearance should be sufficient to avoid "brake drag" and yet close to afford a good "pedal reserve". Manually operated and vacuum-hydraulic actuated brakes require adjustment (or relining) when pedal reserve approximates 2"; that is, when the brake pedal drops to within 2 tt of floor board on hard application. Adjustment may be made with the vehicle resting on jacks. On jacks, brake drag is checked by "feel", rotating the drum in the direction of for ward rotation as adjustment is made.
Note H.
Step-By-step Procedure (Assembly)

IV. WHEEL CYLINDER ASSEMBLY: 1. Do not assemble parts dry. Coat parts and inside of cylinder bore with clean brake fluid. 2. Insert spring (16) cup filler (17), and piston cup (18) into cylinder bore. Cup filler "bumper" and cup lip should face closed end of cylinder.
Step-By-Step Procedure (Adjustment)

1.
Make all adjustments with drums cool.

2. Make sure wheel bearing is correctly ad justed. 3. Placewrench(S/S") on cam and shoe guide stud (A or B) (Figs. 1 and 4) to adjust one shoe. Rotate wrench in the direction of FORWARD wheel rotation to decrease lin ing to drum clearance. Reduce clearance until lining drags on drum.
4. Move wrench slightly in opposite direction, to increase clearance, until drag is re lieved. Then move wrench slightly (7 0 to 10 0 ) to increase the working clearance (1" to l-l/Z" movement through arc swung by S" wrench).
BRAKES ADJUSTMENTS Section J Page S
SERVICE SPECIFICATIONS
LINING LENGTH (MEASURED INSIDE ARC) (BOTH LININGS) 12-1/S" Drum Diameter (lZS0) lZ-7/S" 13" Drum Diameter (l27 0 ) 13-23/32" IS" Drum Diameter (127 0 ) .15-15/16" LINING WIDTH 12-1/S" Drum Diameter 13" Drum Diameter 15" Drum Diameter 2-1/4" 2-1/4" 2-1/4"
LINING THICKNESS(STANDARD LINING) lZ-1/8". 13", IS" Drum Diameters 5/16" LINING RIVET, STANDARD NUMBER 12-1/8",13" Drum Diameters 7-5 15" Drum Diameter 7-6 WRENCH SIZE Adjustment cam and shoe guide stud (2) head . . . ., . . . . . . . . .
5. Place wrench on opposite cam and shoe guide stude (B or A) to adjust second shoe. Repeat steps 3 and 4.
"Bleeding" The Hydraulic Brake System

Vehicle brake systems using the self-centering
hi-tork foundation brake are bled in similar
manner to other hydraulic systems.
METHOD A: Bleed wheel cylinders in the following order:
1. Cylinder lowest to road. 2. Cylinder highest from road. METHOD B: If brake is mounted so that both cylinder bleeder valves are not at the highest point of their .re spective cylinder bores, it may be necessary to "surge bleed" the system. 1. Bleed brakes at all wheels in regular man ner, using Method A. Z. At each wheel cylinder in turn, open bleeder valve and then kick brake pedal down sharply several times. Close bleeder valve. This action creates turbulance in each cylinder, forcing out any remaining trapped air.
. 5/8"
LINING TO DRUM CLEARANCE Freedom from drag plus cam rotation of. . . . . . . . 7_10
III
BRAKES ADJUSTMENTS Section K Page 1
L-160, L-161, L-162, L-163, L-16S, LC-160, LC-161, LC-162
REAR BRAKES 14-1/8" x 3" } (TYPE "FR-2") FIGS. 1 and 2
REAR BRAKES L-164, L-170, L-171, L-l72, L-l73, L-17S, IS" x 3" } (TYPE IFR-2") FIGS. 1 and 2 LF-170, LF-171, LF-l72
L-174, L-lS0, L-lS1, L-lS2, L-lS3, L-lSS,} REAR BRAKES LC-lS0, LC-lSl, LC-lS2, IS" x 4" LF-190, LF-191, LF-192 (TYPE "FR-2") FIGS. 1 and 2
Wheel cylinder cover
Adjusting slol cover
~.---
Backing plate
----:i~
A23211
Internal View Fig.

External View - Rear Brake - Type "FR-2".
BRAKES ADJUSTMENTS Section K Page 2.
~frr
28 2
11 12
26
'y
A22912
Fig. 2 - Rear Brake, Type "FR-2" - Exploded View.
Item No.
DESCRIPTION
Item No. 2.0 2.1 2.2. 23 2.4 2.5 2.6 2.7 2.8 2.9 30 31 32. 33 34 35 36 37
DESCRIPTION
1 2. 3 4 5 6 7 8 9 10
11
12.
13
14 15 16 17 18 19
Plate, brake backing. Pin, anchor.

Screw, adjusting.
Wheel, star, adjusting.
Lockspring, adjus ting.
Shoe and lining assembly.
Shoe.
Lining.
Rivet.
Pin, shoe guide stud.
Washer, shoe guide.
Clip, "C", spring,sshoe guide.
Spring. brake shoe retracting.
Wheel cylinder assembly.
Body, wheel cylinder.
Pis ton as s em bly (long pis ton).
Piston (long),
Cup, pis ton.
Protector segment, cup, pis ton.
Spring. Piston assembly (short pis ton). Piston (short).

Cup, piston.
Protector segment, cup, pis ton. Boot assembly, Push rod. Valve, bleeder. Cover, wheel cylinder. Bolt, wheel cylinder. Lockwasher, wheel cylinder bolt. Tube assembly. connecting. Fitting, tube, connecting.
Fitting, tube, connecting.
Bolt, fitting, tube, connecting.
Washer, fitting, bolt.
Washer, fitting, bolt.
Cover, adjusting slot.
HYDRAULIC BRAKES
BRAKE SHOE ADJUSTMENTS AND SERVICING
FRONT BRAKES L-210, L-211, } 16-1/211 x 3-1/211 LF-210, LF-211, LF-212, LF-220, LF-221, LF-222 (TYPE flFR-2S") FIGS. 3 and 4
Wheel cylinder cover
Brake shoe linings
Brake hose connection
Brake spider - - - " Internal View
Wheel cylinder
Dust shield
A-23207
External View
Fig, 3 - Front Brake - Type "FR-2S".
PRI~TEO
IN UNITED STATES 01"' ."'ItRICA
41 42 43 44
lUI
12
I
11
I
T 31
19
31
10
A-22911
Fig.
Item No.
1
- Front Brake, Type "FR-2S" Exploded View.

Item No, DESCRIPTION Spring.
Piston assembly (short).
Piston (short).
Cup, pis ton.
Protector segment, cup, piston.
Boot assembly.
Push rod.
Valve, bleeder, wheel cylinder.
Cover, wheel cylinder.
Bolt, mounting, wheel cylinder.
Lockwasher, cylinder mounting bolt.
Fitting, distributor, fluid.
Bolt, mounting, dis tributor fitting.
Lockwasher, dis tributor fitting bolt.
Tube assembly, connecting (short).
Tube assembly, connecting (long).
Bolt, fitting, wheel cylinder.
Gasket, fitting, inlet,
Fitting, inlet, fluid.
Gasket, bolt, fitting .
Dus t shield.
B oIt, moun ting, dus t shield. Lockwasher, dust shield mounting bolt.
DESCRIPTION Spider and pin assembly. Pin, retracting, spring, Pin, anchor, Wheel, driven, adjusting worm. Wheel, driven, adjusting worm, Worm, adjusting shoe. Sleeve, adjus ting worm. Washer, end thrus t, adjus ting worm, Ring, snap, worm retainer. Shoe and lining assembly. Shoe, Lining. Rivet. Pin, shoe guide. Washer, shoe guide pin, Clip, "C", spring, shoe guide. Spring, retracting, shoe toe (long). Spring, retracting, shoe heel (Short). Wheel cylinder assembly. Body, wheel cylinder. Pis ton assembly (long). Pis ton (long). Cup, pis ton. Protector segment, cup, piston.
25
2 3 4 5
26
27 28
29
30 31 32
33 34 35
6 7 8 9
10 11 12 13 14 15 16 17 18 19
36
37
38
39 40
41
4.2
43 44 45
.20
21
2.2
23
46
47
24
BRAKES ADJUSTMENTS
Section K
Page 5
REAR BRAKES 16-1/2 11 x 7-1/8 11 L-204, L-210, L-211 (TYPE FR-2-SD) { FIGS. 5 and 6)
Wheel cylinder Retracting spring (long)

~-~=
~
~
Wheel cylinder cover Bleeder valve Brake shoe linings
Retracting spring (short)

A23 195
Internal View.
External View (Dust Shield Removed). Fig. 5 - Rear Brake - Type "FR-2SD".
PRINTED IN UNITED STATES OF'" AMERICA
Fig, 6 - Rear Brake - Exploded View - Type "FR-2SD".
Item No.
DESCRIPTION Spider and pin assembly.

Pin, retracting spring.
Pin, anchor.
Screw, adjus ting.
Wheel, driven, adjusting worm.
Worm, adjusting, shoe.
Sleeve, adjusting worm,
Washer, end thrust, adjusting worm.
Ring, snap, worm retainer.
Shoe and lining assembly.
Shoe.
Lining.
Rivet.
Pin assembly, shoe guide.
Washer, shoe guide pin.
Clip, flC", spring, shoe guide.
Spring. retracting, shoe toe (long),
Spring, retracting, shoe heel (shott).
Wheel cylinder assembly, upper.
Wheel cylinder assembly, lower. Body, wheel cylinder, upper. Body, wheel cylinder, lower. Gasket, port plug. Screw, port plug.
Item No.
DESCRIPTION Piston assembly (long),

Pis ton (long).
Cup, piston.
Spring.
Piston (short).
C up, pis ton.
Boot assembly.
Push rod.
Valve, bleeder, wheel cylinder.
Bolt, mounting, wheel cylinder.
Lockwasher, cylinder mounting bolt.
Tube, assembly, connecting, wheel
cylinder. Bolt, fitting, inlet. Gasket, fitting, inlet. Fitting, inle t, fluid. Gasket, bolt, fitting. Dust shield, assembly. , Bolt, mounting, dust shield. Lockwasher, dust shield mounting bolt.
1 2 3 4 5 6 7 8 9 10
11
12
13
14 15 16 17 18 19 20 21 22
23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45
Adjusting Adjusting outer brake shoe
Fig. 9 - Brake Adjustment, Type wFR-2SD" Brake.

To adjust outer brake shoe, insert wrench in adjustment slot until flat washer on wrench contacts dust shield (see Fig. 9). To ,adjus t inner brake shoe, insert wrench in adjus trnent slot until recessed area on wrench just enters dust shield; this will assure proper engagement of brake tool in inner ad jus trnent worm.
A22939
MAINTENANCE AND ADJUSTMENT WAGNER SELF-CEl'{TERING TYPE FR-2, TYPE FR-2S AND TYPE FR-2SD BRAKES
The development of the Wagner type FR-2 (Figs. I & 2), type FR-2S (Figs. 3 &: 4), and type FR 2SD (Figs. 5 & 6) brakes has created new vistas of greater braking efficiency in the medium and heavy duty truck field. The type FR-2 brake makes available to medium weight trucks. the advantages of full self-energization (shoe wrapping action caused by the drag of the drum on the liners). The type FR-2S and the type FR - 2SD bring the advantage of full self ener gization to the heavy duty field, and, in addition, make it possible for vehicles of 30,000 to 45,000 lbs. gross weight to utilize the high efficiency of hydraulic braking power to the fullest extent. Heretofore, heavy vehicles have been limited to a very few special appli cations of hydraulic braking power. The fact that these brakes incorporate the greatest pos sible use of self-energization in drums of the same or smaller sizes than those now in use is of tremendous importance in solving the braking problems of medium and heavy duty trucks. The basic design of these brakes is the same. The FR-2 and the FR-2S each incorporate two identical shoes and two identical wheel cylinders. The major difference is that the FR-Z uses a backing plate while the FR-ZS is mounted on a spider. The FR-ZSD is a dual type brake, equipped with four shoes. Its appearance is comparable to two FR-ZS brakes placed back to back, and it employs two Siamese Twin-type
Fig. 7 - Brake Adjustment, Type wFR_2w Brake.
worm
VJ.oIf-- Backing plate
14----Brake adjusting wrencb
A.23450
Fig. 8 - Brake Adjustment, Type "FR-2S" Brake.

PRINTEO IN UNfTEO STATES OF AI'IlERICA
L-UNE MOTOR TRLiCK SERVICE MANUAL

and a retainer snap ring. Adjustments are made by inserting a 3/8" hex wrench in the worm and turning in the proper direction for the de sired adjustment. The worm rotates the worm wheel which, in turn, threads the adjusting screw in the direction which the wrench is turned. When the brakes are applied the wheel cylinder pistons apply force against the toe and heel of each shoe. As the shoe linings come into contact with the drum, self-energization develops. The rotation of the drum pulls the shoes a'gainst the drum surface to multiply the forces exerted on the drum and produce additional braking action. If the vehicle is in forward motion, this self energization, or wrapping action, pushes the shoe heels against the anchor pins. In back ward motion the shoe toes are forced against the adjusting screws which then serve as anchor pins. The anchors are free to rotate within their supports, so that when the brake is appUed the pin will turn with the shoe. In addition, the anchors are slotted to allow the shoe heel to slide inwardly or outwardly along the axle radius to center the shoe properly in relation to the drum. Self-centering of shoes when the vehicle is in backward motion is accomplished by rounded shoe toes which pivot on the adjusting screws. The shoes on these brakes are floating shoes. Each shoe is held in position by a shoe guide pin, washer, shoe guide spring "C" clip and two shoe return springs. On the FR-2 brake the toe and heel shoe return springs are the same. On the FR-2S and the FR-2SD, each shoe heel spring is short, hOQked to the anchor end of the shoe and a proje<;:tion on the anchor pin; each shoe toe spring is long, hooked between the toe end of the shoe and a spring pin centered on the spider.
wheel cylinders to actuate the dual shoes. The shoes of all these brakes are arranged with the toes diagonally opposite each other and the double end wheel cylinders are placed between the toe of one shoe and the heel of the other. An equal amount of hydraulic pressure is thus applied at each end of each shoe. Shoes are always forward acting, independently actuated in the direction of rotation. Shoes anchor at either toe or heel depending upon the rotation of the drum. The FR-2 brake is constructed for use on the rear axle of medium weight trucks and buses. As previously mentioned, the major difference of this brake from the other two is that the as sembly is mounted on a backing plate. Riveted to this backing plate are two anchor and adjust ing supports. Into each anchor and adjusting support is placed on anchor pin at one end of the support and a star wheel and adjusting sc.rew at the other end. The adjusting mechanism is . assembled as follows: The adjusting screw is threaded into its end of the support, the star wheel is placed in the slot of the support so that the keys inside of the wheel fit into the lengthwise grooves of the adjusting screw, the star wheel being held in the correct adjustment position by a locks pring. Adjustments are made through a slot in the backing plate opposite the star wheel by placing the special adjusting tool or screwdriver through the slot and turning the star wheel to achieve the desired adjustment. The FR-2S is constructed for the front axles of vehicles having a gross weight of 30,000 to 45,000 Ibs. and is used in conjunction with the FR-2SD rear axle brake. These brakes are mounted on malleable iron spiders, the FR-2S on a single sided spider, and the FR-2SD on a double sided spider. The adjusting and anchor support on these brakes is cast as an integral part of the spider. The principle adjustment difference is that the adjusting screw is operated by a worm and worm wheel instead of a star wheel. The FR-2SD is designed with four shoes, two on each side of the spider. These four shoes offer advantages over two wide shoes in that they provide greater equalization of brake lining pressure on the entire width of the drum surface, more rapid heat dissipation, and longer lining and drum life. Dual shoes also simplify and yet permit greater accur,acy of adjustment when compensating for lining wear. Adjusting mechanisms are similar to the ad justment mechanism on type FR-2. Each ad justing screw is threaded into a worm wheel placed in a slot located in its support. The worm wheel is engaged with a worm which is rotated to effect adjustment. The worm is en closed in a removable sleeve and worm and sleeve are held in the support by a thrust washer
Disassembly FR-2 (Fig. 2)1 FR-2S (Fig. 4) and FR-2SD lFig. 6) Brakes
Note A. The first disassembly operation is always removal of the brake shoe re tracting springs. With brake spring pliers, slip looped ends off pins or projections on the anchor and ad justing supports. When the wheel cylinder connecting tube is removed, not position of tube and fittings on the brake to avoid er ror in reassembly. Difficulty may be encountered in the bleeding operation if tube is assembled in the wrong lo cation. Whenever shoes are removed, always dismantle adjusting mechanism and clean dirt, dust and grease from the parts and supports. Care should be taken to distinguish the adjusting
Note B.
Note C.

screws as those of the left or right brake. The left brake adjusting screws have a left hand thread, and the right brake screws have a right hand thread. Neither can be assembled to the op posite brake.
Assembly
Note D. Each brake utilizes two wheel cylin ders which are identical. The piston actuating the toe of each shoe has provision for a longer stroke than the other piston. This is to compensate for adjustments made on the shoe which move the shoe toe away from the wheel cylinder. Thus the long stroke piston is built longer than the short stroke piston, and is also identified by a circular groove machined at the bottom of the push rod socket. The cylinder casting is constructed with the bleeder valve and connecting tube inlets offset toward the short stroke end of the cylinder. PISTONS MUST BE ASSEMBLED IN THE PROPER ORDER WITHIN THE CYLINDER. Otherwise, fluid will enter the cylinder chamber improperly and may be forced out past the short stroke piston. Do not lubricate shoe adjustment mechanism or other parts of the brake. Lubrication will cause dirt and dust to collect and. solidify in the adjust ment mechanism. When replacing shoes make certain that the toe or cutaway end of each shoe is aligned with the adjusting screw, and the heel of each shoe with the anchor pin -- otherwis e, adjust ments cannot be made. When replacing shoe retracting springs, place the straight ends of the springs in the notched holes in the brake shoes, and, with a brake spring pliers, slip the looped ends over the pin or anchor pin projection as required. The FR-2 type retracting springs are of equal length and loop over a pin mounted in the anchor and adjusting support. Each shoe on the FR-2S and the FR-2SD type brakes has one long toe spring which loops over a pin mounted on a centered location on the spider, and one short heel spring which loops over a projection on the anchor pin.
step-By-step Procedure (Disassembly)

Before beginning the following steps on the FR-2S and FR-2SD, remove the dust shield attaching bolts and lift off the dust shields. I. TO REMOVE SHOE ASSEMBLIES: 1. Remove brake shoe retracting springs. (Refer to Note A.) Z. Pry off shoe guide spring "C" clip and lift washer off of shoe guide stud. Shoes will slide off easily. The anchor pins should easily pull out of the supports. Note E. II. TO REMOVE WHEEL CYLINDERS
WITHOUT DISTR UBING SHOES:
3.
1. Remove brake shoe retracting springs. (Refer to Note A.)

2. Remove connecting tube fitting bolts from wheel cylinder. 3. Remove wheel cylinder bolts. 4. Spread shoes away from cylinder until push rods are cleared. Lift out cylinder and cover. III. TO REMOVE ADJUSTING MECHANISM: Note F.
Note G.
1. Remove shoes from brake.

2. Rotate adjusting screw, backing off adjust ment to thread it free of star wheel or worm gear. 3. Push adjusting screw out of support. On FR-2 type, lift star wheel and lock spring from slot. On FR-2S and FR-2SD types, pry worm retainer snap ring from support and remove thrust washer, worm and worm wheel from slot. IV. TO DISASSEMBLE WHEEL CYLINDERS:
step-By-step Procedure (Assembly)

1. Take push rods out of boot assemblies and slip boots off ends of cylinders.
2. Remove pistons and spring by pushing either piston through and out of cylinder. 3. Cups are removed by slipping cup protector segments off and working cups over the end of the pistons.
PRINTED IN UNlTEO STATES OF' AMERICA
The brakes are easily assembled in reverse order to disassembly. V. TO ASSEMBLE WHEEL CYLINDERS: 1. Do not assemble parts dry. Coat parts and inside of cylinder bore with clean brake fluid before assembly.

VIII. TO REPLACE SHOE ASSEMBLIES: 1. For best results new shoe and lining as semblies should have liners of correct thickness, ground (not buffed) to the correct radius, concentric to the brake drum. Z. Slide anchor pins into supports so that anchor can be engaged by the shoe heel.
Z. Stretch cups into place on the pistons. Cup lip must face inward toward spring groove side of piston. 3. Slip cup protector segments into place on each piston. Protector segment is placed behind cup with segment lip facing same direction as cup lip. 4. Slide pistons with spring between them into cylinder chamber. Be sure long stroke piston. and short stroke piston are at the correct ends of the cylinder and the push rod socket in each piston faces outward. (Refer to Note D.) 5. Slip boots over ends of cylinder so that the boot edges fit squarely into the grooves on the casting. Place push rods into assembled boots and cylinder. VI. TO REPLACE ADJUSTING MECHANISM: L Do not lubricate parts. (Refer to Note E.)
3. Replace shoe on backing plate or spider making sure that toe is aligned with the adjusting screw and heel with the slot pro vided in the anchor pin. Slip shoe guide pin through spider or backing plate guide hole located in shoe web. Install washer and shoe guide spring OlC" clip. Repeat step for other shoe or shoes. 4. Replace shoe retracting springs. (Refer to Note G.) On FR-ZS and FR-ZSD type brakes, replace the dust shield enclosure after completing assembly of the brake.
Z. On the FR-ZS and FR-ZSD types, place worm in sleeve and slip them into hole in adjusting support. Open side of sleeve must face worm wheel slot. Insert thrust washer and snap ring; be sure snap ring fit firmly into groove in wall of worm hole. (Omit this step with the FR-Z type brake.) 3. Hold star wheel (FR-Z) or worm wheel (FR-ZS, FR-ZSD) in slot in adjusting support and slide adjusting screw into the outer end of the support so that the keys machined on the inner circumference of the wheel en gage into the keyways on the adjusting screw. Be certain to use the correct ad justing screws for the left and right brakes. (Refer to Note C.) 4. Rotate worm or star wheel to thread ad
justing screw into support.
VII. TO REPLACE WHEEL CYLINDER
WITHOUT DISTRUBING SHOES:
1. Be sure backing plate or spider is clean
so that cylinder and cover will fit properly
when mounted.
Z. Spread shoes as far apart as possible.
Adjustment
Lining to drum clearance adjustment is required when the shoes are relined, and. on occasion, to compensate for normal lining wear. Clearance should be sufficient to avoid "brake drag and yet close enough to afford a good "pedal reserve". lv1anually operated and vacuum-hydraulic actuated brakes require adjustment (or relining) when the pedal reserve approximates Z; that is, when the pedal drops to within Z .. of the floor board on hard application. Adjustment may be made with the vehicle resting on jacks. On jacks, brake drag is checked by feel. rotating the drum in the direction of for ward movement as the adjustment is made.
Step-By-step Procedure (Adjustment) Type FR -2 Brake (Figs. 1 and 7)

1. Make all adjustments with drum cooled to normal temperature. Z. Make sure wheel bearing is correctly ad
justed.
3. Remove adjustment slot covers. 4. Insert special adjusting tool or screwdriver into adjustment slot (A or B) to contact the star wheel. Rotate star wheel toward axles. using outer edge of slot as fulcrum for tool handle, until lining "drags" on the drum. 5. Back lining off drum by rotating star wheel TWO notches away from axle. This will provide sufficient working clearance. 6. Repeat Steps 4 and "5 on Second shoe (B or A). 7. Replace adjustment slot covers.
3. Place cylinder and cover in proper position on the backing plate or spider and fasten securely with wheel cylinder bolts and lock washers. Screw in connecting tube fitting bolt. (Refer to Note B.) 4. Engage notched push rod ends into slots provided at each end of the shoes. 5. Replace brake shoe retracting springs. (Refer to Note G.)

Step-By-Step Procedure (Adjustment) Type FR-2S Brake (Figs. 3 and 8)
1. Make all adjustments with dru:rn cooled to normal temperature. 2. Make sure wheel bearings are correctly adjusted.
(Fi~s. 3 and 8) through adjusting hole (A or B) in dust shield to fit firmly in adjusting worm. Rotate wrench in direction of forward wheel rotation until lining "drags" on the drum.
"BLEEDINGII THE HYDRAULIC BRAKE SYSTEM

Vehicle brake syste:rns using the Type FR-Z., FR-2S, FR-2SD foundation brake are bled in similar manner to other hydraulic sys terns. METHOD A: Bleed wheel cylinders in the following order: FR-2 and FR-2S 1. Cylinder nearest to road. Z. Cylinder highest from the road. Type FR-2SD Dual Brake only 1. Bleeding both cylinders of the FR-2SD brake is accomplished through one bleeder valve located on the high cylinder.
3. Insert brake adjusting wrench
4. Rotate wrench in opposite direction to in crease clearance until drag is relieved. Then rotate wrench one additional turn to provide working clearance. 5. Repeat Steps 3 and 4 on the other shoe. or shoes (B or A).
Step-By-Step Procedure (Adjustment) Type FR-2SD Brake (Figs. 5 and 9)

The rear wheel brakes are adjusted by means of a special 3/8" hex wrench (IH No. SE 1731) which has been designed for the purpose of adjusting either the inner or outer brake shoe but not both shoes at one time. 1. Make all adjustments with drum cooled to normal temperatures. 2. Make sure wheel bearings are correctly adjusted. 3. Insert special wrench (IH No. SE-l731 Figs. 5 and 9) in adjustment slot (A or B) to engage either the inner or outer brake shoe adjusting worm. Rotate wrench in the direction of FORWARD wheel rotation to decrease lining to drum ciearance. Re duce clearance until lining "drags" on drum. 4. Rotate wrench in opposite direction, to in crease clearance, until "drag" is relieved. Then rotate one (1) additional turn to pro vide the proper working clearance. CAUTION: Repeat operation at each shoe (two shoes to be adjusted at each adjust ment slot in dust shie ld). 5. Repeat Steps 3 and 4 at opposite adjust ment slot (B or A). NOTE: For most accurate adjustment it is not advisable to attempt to adjust both brake shoes simultaneously, always pro ceed as outlined above.
PRINTEP IN UNIT!;:!) 5TATE"S OF AME"RICA
METHOD B:
If brake is mounted so that both cylinders are

almost in a vertical plane, it may be necessary to "surge bleed" the system. 1. Bleed brakes at all wheels in regular :manner, using Method A, above. 2. At each wheel cylinder in turn, open bleeder valve and then kick pedal down sharply several ti:rnes. Close bleeder valve. This action creates turbulence in each cylinder, forcing out any remaining trapped air.
BRAKES
ADJUSTMENTS
Section K Page lZ
LINING LENGTH (Measured Inside Arc)
(Both Linings):
FR-Z Brake
14-1/8" Drum Diameter . . . . . . . . . 14-118"
15" Drum Diameter. . . . . . . . . . 15 11
FR-ZS Brake
16-1/Z" Drum Diameter . . . 7-314 11 Block
(Two used per shoe)
FR-ZSD Brake
16-1/Z" Drum Diameter . . . . . 7-314" Block
(Two- used per shoe)
LINING WIDTH: FR-Z Brake 14-118" Drum Diameter . . . . . . . . . . 3"
15" Drum Diameter. . . . . . . . . . . . 3"
15" Drum Diameter . . . . . . . . . . 4"
FR-ZS Brake 16-1/Z" Drum Diameter . . . . . . . 3-1IZ" FR-ZSD Brake 16-1/Z" Drum Diameter . . . LINING THICKNESS (Standard Lining): FR-Z Brake 14-118" and 15" Drum Diameter. . .. FR-ZS Brake 16-1/Z" Drum Diameter. . . . . .. FR-ZSD Brake 16-1/ZI1 Drum Diameter. . . . . . . . .
5/8" 5/8" 3/8"
3-1IZI1
BRAKES ADJUSTMENTS Section L Page 1
L-184, L-190, L-191, L-192, L-193, L-195, } REAR BRAKES LC-190, LC-191, LC-192, 16" x 4" LF-210, LF-21l, LF-212, LF-220, LF-221, LF-222, (TYPE "FR")
L-194, L-200, L-201, L-202, L-205, LC-200, LC-201, LC-202
REAR BRAKES 16" x 5" } (TYPE "FR")
Retracting spring Wheel cylinder
Brake shoe guide washer
Adjusting slot
Brake shoe lining
~L... _ _ _ _ Direction of drum rotat.ion _
Internal View Fig. I - Rear Brake - Type -FR-.
"RINT~P
ExternaJ View
IN UI.UTI'O _TATES 0 ' AMIUUCA
3 i ~.. .' '~~:'.:~.;::~O
5 9
.'
.
,~4
12
@4
,~*,~.!,~,.;
. .. ;:~X, .::'
~1l
: 6-'(1? 1_____________________________________ _
o
o
A-22909
fi
Fig. 2 - Rear Brake, Type "FR" - Exploded View.
Item No.
DESCRIPTION
Item No.
DESCRIPTION Cup, piston.

Ring segment, back-up, piston cup.
Spring.
Pis ton (shor t).
Cup, piston.
R.ing segment, back-up, pis ton cup.
Boot. Cap, boot retainer.
Washer, spring, cylinder mounting.
Link, connecting, pis ton to shoe.
Valve, bleeder, cylinder.
Tube, assembly connector, wheel
cylinder. Gasket, fitting. Fitting, inlet, fluid, connector tube. Gasket, bolt. Bolt, fitting, inlet, brake pipe to cylinder & tube.
Bolt, fitting, inlet, connector tube
to cylinder.
1 2 3 4
5 6
7 8
9
10 11 12 13 14
15 16
17 18
19
20 21 22 23 24
Plate, brake backing. Shoe, lining & adjuster assembly. Shoe & lining assembly. Shoe & insert assembly. Lining. Rivet lining. Screw, adjusting, shoe. W ashe r, end thrus t, adj us ting worm. Sle eve, adj us ting worm. Worm, adjusting, shoe Ring, snap, worm retainer. Wheel, driven, adjus ting worm. Spring, brake shoe retracting. Bolt, shoe guide. Sleeve, shoe guide bolt. Washer, plain, shoe guide bolt. Lockwasher, shoe guide bolt. Nut, shoe guide bolt. Nut, lock, shoe anchor .block. Block assembly, shoe anchor. Wheel cylip.der assembly. Body, wheel cylinder. Piston assembly (long). Piston (long).
25
26
27
28
29
30
31
32
33
34
35
36
37 38 39
40 41 42 43
44
worm
vehicle is moving forward, the shoe heels are wrapped against their anchor blocks by the drum rotation. If the vehicle is backing, the shoe toes are forced against their anchor blocks. Anchor block sides are aligned on the axle radius. Upon contact with the anchor blocks the shoes pivot and, at the same time, move radially along the anchor block sides until they are centered in relation to the drum. Self-ener gization assists brake application equally regardless of the direction of the drum rotation. The brake is thus capable of develop ing the same maximum torque output for a re verse stop that is used for a forward stop, and it is always automatically self-centering.
VJ.C--- Backing plate
r4----Brake adjusting wrench
Disassembly
A23450
Note A.
Fig. 3 - Brake Adjustment, Type "FR" Brake.

MAINTENANCE AND ADJUSTMENT
WAGNER SELF-CENTERING
TYPE "FR" BRAKES (Figs~ 1 and 2)
The Wagner self-centering Hi-Tork Brake is a "floating shoe" type which has two identical shoes (2) (Fig. 2) arranges on the backing plate (1) so that their toes are diagonally oppo site. Two double-end wheel cylinders (21) are arranged so that one cylinder is mounted between each shoe toe and shoe heel. An equal amount of hydraulic force is thus applied at each end of each shoe. The wheel cylinders are not bolted directly to the backing plate; instead, lliey are held in position by shoe anchor block (20). The anchor blocks are bolted to the back ing plate. Each anchor block serves as a shoe stop and shoe centering point and provides the fulcrum around which the shoe pivots when the ::>rake is applied. Both shoes are always pri :nary shoes (forward-acting), independently 3.ctuated in either direction of rotation. Shoes 3.nchor at either toe or heel depending upon the ~otation of the brake drum. A pivot pad is placed it both shoes toe and shoe heel. The pad at the ;hoe toe is an integral part of the shoe adjusting 3crew {7}, a component of the adjusting mech mism, which is placed in the shoe toe on this >rake. The adjusting screw is held in the shoe oe by means of worm wheel (12) which threads >nto the screw. The worm wheel, in turn, meshes vHh a worm (10) which is rotated to effect brake .djustment. The worm has a hex bore so that t can easily be turned with a 3/8" hex brake <rench. Adjustment slots (A and B) (Fig. 1) n the brake backing plate, provide access to ach of the shoe adjusting worms. Jpon brake application, the wheel cylinder pistons 23 and 28) (Fig. 2) apply force agains t toe and .eel of each shoe. Upon contact of shoe liners 5} with the drum, self-energization (shoe wrap ing action caused by drag of the drum on the inings) wraps both shoes into the drum. If the
PFlINTJ:D IN UNITED STATES OF' "..,ERICA
The first disassembly operation is al ways removal of brake shoe retracting springs {13} (Fig. 2). With brake spring pliers, slip looped end of spring off of the spring hook located at the toe or adjustment end of each shoe.
Note B.
If wheel cylinder connecting tube (39) and bleeder valves (38) are re moved, mark wheel cylinder ports to which connecting tube is attached to avoid error in reassembly. Diffi culty will be encountered in bleeding operation if tube is assembled in wrong location.
Whenever shoes are removed, always dismantle adjusting mechanism and clean grease, dust, and dirt from parts and from chambers within the shoe.
Note C.
Step-By-Step Procedure (Disassembly)

I. REMOVAL OF SHOE ASSEMBLIES (2): 1. Remove brake shoe retracting springs (13). (Refer to Note A). 2. Remove shoe guide bolt nut (18), lockwasher {17}, and washer (16), holding shoe in place. Shoe {2} easily lifts off. 3. All other parts may then easily be removed. (Refer to Notes B and C). II. REMOVAL OF WHEEL CYLINDER {21} WITHOUT DISTURBING SHOES: 1. Remove brake shoe retracting springs (l3). (Refer to Note A). 2. Disassemble cylinder connecting tube {39} and tube fitting (41). (Refer to Note B)
3. At anchor block (20) of cylinder, loosen anchor block lock nuts (19). It is not neces sary to completely remove these nuts.

the cylinder (Greatest length from inlet port to end of cylinder) must be assembled to the backing plate so that it faces the: (1) Shoe Toe (ad justment end of shoe). (2) Adjust ment slot in backing plate. Note E. Do not lubricate shoe adjustment mechanism or other parts of the brake. Lubrication will cause dust and dirt to collect and solidify in the adjustment mechanism. When replacing shoes, make sure that shoe adjusting worm (10) (Fig. 2) is aligned with adjusting slot (A or B) in backing plate. Shoes (2) can be as sembled backward, however, the brake cannot be adjusted. When replacing shoe retracting springs (13), place hooked end on shoe pins at shoe heel and then, with brake spring pliers, slip looped end of spring on hook at toe end (adjustment end) of shoe.
4. Spread shoes away from cylinder until con necting links (35) are cleared. 5. Push anchor block (20) away from backing plate (1) until clearance is sufficient for cylinder removal. 6. Lift out cylinder, complete with connecting links. Be careful not to misplace spring washers (34). I I I. REMOVAL OF SHOE ADJUSTMENT
MECHANISM:
Note F.
1. Remove shoes (2) from brake.

2.. Rotate adjusting screw (7), threading it free of worm wheel (12). Note G. 4. End thrust washers (8), sleeve (9), worm (10), and worm wheel (12) may now easily be removed. IV. WHEEL CYLINDER (21) DISASSEMBLY: 1. Pry off each boot retainer cap (33), Boot (32) and connecting link (35) will corne with the cap.
3. Pry worm retainer snap ring (11) from shoe.
step-By-step Procedure (Assembly)

2. Internal parts may now be forced out of one end of cylinder. 3. Slip cup back up ring segments (26, 31) off of each piston assembly (23, 28). 4. Cups (25, 30) can now be stretched and forced off of each piston. Take care not to mar piston bearing surface or cup groove. 5. In turn, clamp each connecting link (35) in vise. Pry off each boot retainer sleeve. Remove boots (32). The brake is easily assembled in reverse order to disassembly. V. WHEEL CYLINDER ASSEMBLY: 1. Do not assemble p~rts dry. Coat parts and inside of cylinder bore with clean brake fluid before assembly. 2. Stretch cups (25 and 30) into place on pistons (24 and 29). Cup lip must face inward to ward spring groove side of piston. 3. Slip cup back up ring segments (26 and 31) into place on each piston. Segment must be placed behind the cup lip and segment lip must face in same direction as cup lip. 4. Assemble boots (32) and boot retainer sleeves to connecting links (35). Force sleeves over boots to hold boots in place on links. 5. Place long stroke and short stroke piston assemblies (23 and 28) in correct positions in cylinder with spring (27) between pistons. Piston connecting link sockets must face out ward and cup lips face inward. (Refer to Note
Assembly
Note D. Wheel cylinders are identical. One side of the cylinder has a long stroke, in comparison to the other side, to take care of increased piston travel made necessary when the brake is adjusted to compensate for lining wear. The cylinder inlet and bleeder ports are offset toward the short stroke side. The long stroke piston has greater length than the short stroke piston and is also identified by a circular slot machined at the bottom of the connect ing link socket. Pistons must be assembled in proper position within the cylinder. If pistons are reversed, fluid will have difficulty entering the cylinder chamber and it may be forced out of the short stroke side of the cylinder. The long stroke side of
D).
6. Place assembled boots and links in boot re tainer caps (33) and fit on cylinder. Crimp each cap, in at least three places, into grooves machined on ends of cylinder.

V I. REPLACEJMENT OF SHOE ADJUST
3,
MENT MECHANISM:
Slip guide sleeve (15) on guide bolt (14). Assemble guide washer (16), lockwasher (17), and lock nut (18). Tighten nut securely. Repeat Steps 2 and 3 for second shoe. Replace shoe retracting springs (13). (Refer to Note G,)
1. Do not lubricate parts. (Refer to Note E).

4.
2, Assemble end thrust washers (8), sleeve (9). worm (10), and worm wheel (12) in
place. Sleeve slot must face the worm wheel to allow worm and wheel to mesh.
5.
3. Push worm retainer snap ring (11) in place,

making sure it snaps into the groove pro vided in the shoe.
4. Start adjusting screw (7) into worm wheel (12) thread. Adjust to full off position.
Curvature of pad on adjusting screw must be in proper plane to permit it to rock on anchor block when shoe is replaced on back ing plate.
Adjustment
Lining to drum clearance adjustment is required when shoes are relined and, on occasion, to compensate for normal lining wear, Clearance should be sufficient to avoid "brake drag" and yet close to afford a good "pedal reserve", Manually operated and vacuum-hydraulic actu ated brakes require adjustment (or relining) when pedal reserve approximates 2 "; that is, when the brake pedal drops to within 2 It of the floor board on hard application. Adjustment may be made with the vehicle resting on jacks. On jacks, brake drag is checked by '!feel", rotating the drum in the direction of for ward rotation as adjustment is made.
VII. REPLACEMENT OF WHEEL

CYLINDER WITHOUT DISTURBING SHOES:
I, Make sure that backing plate is clean so
that cylinder and anchor block (20) will fit properly when mounted.
2. Make sure spr ing washers (34) are in

position on the two lugs machined on the cylinder casting.
3.
Spread shoes as far apart as possible. Holding wheel cylinder so that long stroke side of cylinder faces shoe toe and backing plate adjustment slot, slip mounting lugs into place in the anchor block (20). (Refer to Note D), Slip connecting link ends into sockets pro vided in the shoes. Tighten anchor block locknuts (19), with a TORQUE WRENCH. Self-locking nuts, to be effective, must not be over tightened. Assemble cylinder connecting tube (39), (Refer to Note B under Disassembly.) Replace brake shoe retracting springs (13), (Refer to Note G).
1.
step-By-step Pro cedure (Adjustment)

1. Make all adjustments with drum cooled to normal temperature.
2. Make sure wheel bearing is correctly ad justed.
3. Remove adjustment slot covers.
>.
).
'III. REPLACEMENT OF SHOE ASSEMBLIES
4. Insert brake adjusting wrench in adjust ment slot (A or B) (Figs. 1 and 3) to contact shoe adjusting worm (10). Rotate wrench in the direction of FORWARD wheel rota tion to decrease lining to drum clearance. Reduce clearance until lining "drags" on drum. 5. Rotate wrench in opposite direction, to in crease clearance, until drag is relieved. Then rotate wrench one additional turn to provide working clearance. 6. Repeat Steps 4 and 5 on the second shoe (Adjustment Slot B or A). 7. Replace adjustment slot covers.
For best results, new shoe and lining as semblies (2) should have liners of correct thicknes s ground (not buffed) to correct radius, concentric with the brake drum. If this is not done, readjustment may be re quired after liners are "worn in". Replace one shoe on backing plate (1) making sure adjustment worm (10) is aligned with adjustment slot (A or B), (Refer to Note F.)
"RtNT/:) IN UNITI:D STATES
or
"MERICA
tlBLEEDING" THE HYDRAULIC

BRAKE SYSTEM
Vehicle brake systems using the self-centering

hi-tork foundation brake are bled in similar
manner to other hydraulic systems.
METHOD .A: Bleed wheel cylinders in the following order:
1. Cylinder lowest to road.

2. Cylinder highest from road. METHOD B: If brake is mounted so that both cylinders are
almost in a vertical plane it may be necessary
to "sur ge bleed" the system.
1. Bleed brakes at all wheels in regular
manne r, us ing Method A.

2. At each wheel cylinder in turn, open bleeder
valve and then kick brake pedal down sharply
several times. Close bleeder valve. This
action creates turbulence in each cylinder,
forcing out any remaining trapped air.
LINING LENGTH (measured inside arc) (Both Linings): 16" Drum Diameter 16-1/8" LINING WIDTH: 16" Drum Diameter. LINING THICKNESS (Std. Lining): 16" Drum Diameter. TORQUE WRENCH READING, SHOE
ANCHOR BLOCK LOCKNUT:
16" Drum Diameter
(3/4"-16 Thrd.) 175-219 lb. ft.
3/8" . . . 4", 5"
BRAKES ADJUSTMENTS Section M Page 1
PARKING BRAKE
FOR LM-120, L-l30, L-150, LM-150, L-160, LC-160, L-170, LF-170 SERIES TRUCKS
PARKING BRAKE
FOR L-180, LC-180 SERIES TRUCKS
Parking Brake Adjustments (See Fig. 1)

Note: Perform operations in sequence given: 1. Place parking brake lever in extreme for ward (release) position. NOTE: Brake cam lever must rest squarely on the upper brake band bracket. If necessary readjust linkage. 2. The lining to drum clearance of .020" to .030" is obtained as follows: (a) Adjust anchor screw nut (1) until .020" to .030" clearance is obtained at side of the stop screw. (b) Tighten nuts (4) on adjusting screw bracket bolt (5) to give .020" to .030" clearance between lower half of lining and drum. (c) Adjust lining clearance for upper half of band to .020" to .030" by turning nut (2) on adjusting bolt (3). (d) La ck all adjustments and recheck clearances

Note: Perform operations in sequence given: 1. Place parking brake lever in extreme for ward (release) position. NOTE: Brake cam lever must rest squarely on the upper brake band bracket. To correct this position, rennve clevis pin and readjust yoke. 2. The lining to drum clearance of .020" to .030" is obtained as follows: (a) Adjust anchor screw nut (1) until .020" to .030" clearance is obtained at side of the stop screw. (b) Tighten nuts (4) on adjusting screw bracket bolt (5) to give .020" to .030" clearance between lower half of lining and drum. (c) Adjust lining clearance for upper half of band to .020" to .030" by turning nut (2) on adjusting bolt (3). (d) Lock all adjustments and recheck clear ance s.
.020 to .030" clearance .020 to .030"

clearance
--,,-__-4
3 .020 to .030" clearance .020 to .030" clearance

Fig. 2
A.22888
A-22889
Fig. I
BRAKES ADJUSTMENTS Section M Page 2
PARKING BRAKE
FOR L-190 AND LF-190 SERIES TRUCKS.
L-200. L-201, L-202, L-204 TRUCKS

Note: Perform operations in sequence given:
PARKING BRAKE
FOR L-205, L-210, L-211, L-212, LF-210,
LF-211, LF-212, LF-220, LF;,.221
LF-222 TRUCKS

Note: Perform operations in sequence given:
1. Place parking brake in extreme forward

(release) position. NOTE: Brake cam lever must rest squarely on the upper brake band bracket. To correct this position, remove clevis pin and readjust yoke. 2. The lining to drum clearance of .020" to .030" is obtained as follows: (a) Adjust anchor screw nut (1) until .020"to .030" clearance is obtained at side of the stop screw, (b) Tighten nuts (4) on adjusting screw bracket bolt (5) to give .020" to ,030" lining clearance to drum for lower half of shoe. (c) Adjust upper half of shoe lining clearance to ,020" to .030" by turning nut (2) on adjusting bolt (3). (d) Lock all adjustments and recheck clearances.
1. Place parking brake lever in extreme for

ward (release) position. NOTE: Brake cam lever must rest squarely on the upper brake band bracket. To correct this position, remove clevis pin and readjust yoke. 2. The lining to drum clearance of .020" to .030" is obtained as follows: (a) Tighten nuts (3) on bolt (4) to give .020" to .030" clearance between lower half of shoe and drum. (b) Tighten nuts (1) on adjusting bolt (2) to give .020" to .030" clearance be tween upper half of brake shoe and drum. (c) Tighten nuts (5) on bracket bolt (6) just enough to hold adjustment obtained in paragraph (b). (d) Lock all adjustments.
5-+-+ti~~~~
6--'""-
F j g. 3
Fig. If
CLUTCHES Specifications and Index Page 1
CLUTCH GROUP
Motor truck models and their corresponding clutch models are shown in the following list. Clutch model specifications will be found on specification page 2.
TRUCK MODEL
CLUTCH MODEL
TRUCK MODEL
CLUTCH MODEL
RK-IOB L-IIO. . .. . .......... .

RK-IOB L-120. . . . . .......... .
RK-IOB LM-120 . . . . ......... .
RK-IOB L-130 . . . . . . . . . . . . . . . . . . . .
LB-140 . . . . . . . . . . . . . . . . . . .
RK-IOB L-150 . . . . . . . . . . . . . . . . . . . .
RK-IOB L-153. . . ......... .
LM-150 .......... .
RK-IOB R-IIA-l L-160. . . ....... .
R-IIA-l L-163. . . . . . .......
L-164 . . . . . . . . . . . . . . .
R-IIA-l R-IIA-l L-165 . . . . . . . . . . . . . . . . . . . .
LC-160 . . . . . . . . . . . . . . . . . .
R-IIA-l L-170. . . . . . . . . . . . . .
R-l1A-1 L-l 73 . . . . . . . . . . . . . . . . . .
R-IIA-l L-174. . . . . . . . . . . . . . . . .
R-IIA-l L-l 75 . . . . . . . . . . . . . . . . . .
R-IIA-l R-IIA-l LF -170. . . . . ........ .
L-IBO. . . . . . .
RK-IIA-l L-IB3. . . . . . . . . . . . . . .
RK-IIA-l
L-184 . . . . . . . . . . . . . . . . . . . .
RK-IIA-l L-IB5 . . . . . . . . . . . .
RK-IIA-I RK-12-1Z LC-IBO . . . . . . . . . . . . . . . . . .
RK-IZ-15 L-190 . . . . . . . . . . . . . . . . . .
RK-IZ-15 L-193 . . . . . . . . . . . . . . . . . . .
RK-12-15 L-194 . . . . . . . . . . . . . . . . .
R-14-15 L-195 . . . ......... .
LC-190 . . . . . . . . . . . . . . . .
R-14-15 LF-190 . . . . . . . . . . . . . . . .
R-14-15 L-200 . . . . . . . . . . . . . . . . . .
R-14-15 L-204 . . . . . . . . . . . . . . . . . . . .
R-14-15 L-205 . . . . . . . . . . , . . . . . . . .
LC-200 . . . . . . . . . . . . . . . . . . .
R-14-15 L-210 . . . . . . . . . . . . . . . . . . . .
LF-210 . . . . . . . . . . . . . . . . .
R-14-15 R-15-B L-220 . . . . . . . . . . . . . . . . . . . .
R-15-B L-ZZ5 . . . . . . . . . . . . . . . . . . . .
LF-220 . . . . . . . . . . . . . . . . . . .
L-Z30 . . . . . . . . . . . ...
LF-230 . . . . . . . . . . . . . . . . . . .
Page Z
INDEX
SPECIFICA TIONS . . . . . . . . . . , . . .
SECTION "An
A.djustments . . . .
A.ssembling clutch
:::;lutch chatter . . .
:::;lutch description . . . . . . . . . . . . . Jriven member assembly . . . . . . . . :nstalling clutch . . . . . . . .
)verhaul fixture. . . . . . . ..... ::ledal adjustment . . . . . . . . . . . . . . 'Zelease levers . . . . . . . . . . . . . . . . 'Zemoval . . . . . .
iervicing clutch . . . .
1 To 3 7
9
.
.
.
.
.
4 4 B 5 9 7 4
5, 6
Pl ~ 't:l ..... OQP- (\\ l

(\\H
'1jPlUl()
N~~~
OC
g- o ()
[/l
>(Pl::r::
::tM
Ul
- -
CLUTCH SPECIFICATIONS - - - -_ _
---------------.............
-----
CL UTCH MODELS (IH) Clutch Model (Manufacturer). . Number of plates . . . . . Vibration dampener . . . . Pressure Springs; Number used . . . . . . . . Pounds pressure . . . . . at. . . . . . . . . . . . Clutch Facings: Number used . . . . . . . . . Release Lever Adjustment: Flywheel surface to levers . . . . . . . . . . Clutch Pedal Free Travel. . . .
RK-IOB 10-TT 1 Coil Spring
R-llA-1 Il-TT 1 Coil Spring 12 145 1-7/16 11 2
RK-12-12
RK-12-15
R-14-15
14-TT
1
Coil Spring
15
175
1-13/16 11
2
R-15-8
15-TT
1
Coil Spring
18
175
1-13/16 11
2
tTl
12-TT 12-TT 1 1 Coil Spring Coil Spring 12 145 1-7/16 11 2 15 145 1-7/16 11 2
o -l o ~
n
C
3:
9 145 1-7/16 11
2
-l
7\
tTl
~
(f)
1-13/16 11 1 to 1-1/2 11
2" 1 to 1-1/2 11
2-1/8 11
2-1/8 11
n
2-5/8 11
1 to 1-1/2"
2-3/4 11
1 to 1-1/2 11
<
tTl
1 to 1-1/2 11 1 to 1-1/211
Capscrew size for removal and installation . 3/8-16xl-3/4 11 3/8-16xl-3/4 11 3/8-16x2 11

-
3:
3/8-16x2 11 3/8-16x2-1/4 11 3/8-16x2-1/2"

------------
CLUTCH Section A Page 1
CLUTCH
Clutches on the R-110 through R-190 series chassis (1011, II" and 12" clutches) use a new cushion type driven member. this re quires a change in release lever settings to accommodate the new thicker cushion type driven member. Figure 1 illustrates the 10. 11 and 12 inch clutches and Figure 2 illustrates the 14" clutch used in R-line trucks (see following page). Refer to chart on page 3 for truck models and release lever settings. The clutch linkage on R-lSO and up chassis has two holes in the clutch release lever (see Figures 3 and 4 on page 4) to assure clean clutch release and afford the operator a choice between pedal pressures and travel. The clutch linkage adjustable yoke can be installed in either hole on the release lever to suit operator's choice. The clutch pedal free travel for all R-line chassis is 2 inches. It is important that clutch pedal free travel be maintained to avoid pre mature clutch failure. Keep clutch control linkage lubricated.
Clutch release bearing sleeves on all R-line chassis incorporate a lubricator fitting to pro vide means of lubricating the clutch release bearing. sleeve and fork without their removal from chassis. Lubricate as follows:
Fill release bearing sleeve using hand gun. Do not over-lubricate. Lubricate every 15,000 to 20,000 miles. Under unusual "Stop and-Go" driving conditions lubricate every 10,000 miles. Use lubricant comparable to "Lubriplate No. 110."
CTS 12-MARCH 1953 (Supplemental pages (or CTS)l).
PRINTEO IN UNITED STATES OF' AMERiCA.
CLUTCH
Section A Page 2
R-L1NE MOTOR TRUCK SERVICE
III
II
-Release lever
Adjutinr screw
A..J051T
Fig. 1 Clutch Models RK.10-B, R-llA-l, RR1212, RK12-15 (10",11" and 12" clutches). See cha1't on page 3 for truck models, thickness of pressure plate spacers and release lever settings.
Release lever
Adjusting screw
Loclmut
A-3051B
Fig.2 - Clutch Model RK-14-15 (14" Clutch). See chart on page 3 for truck models, thickness of back plate spacers and release lever settings.
Q en
...
I
....
<il
~=
~
~
E
The following chart shows truck model, clutch model number, type of driven member, thickness and part number of spacer plate, and release lever settings for R- LINE Chassis when using the SE-990 Clutch Overhaul Fixture.
SPACER THICKNESS AND NUMBER A LEVER SETTING C TRUCK MODEL IH CLUTCH MODEL NUMBER TYPE OF DRIVEN MEMBER LEVER SETTING B R-ll0, R-120, R-130, R-lS0, RA-120, RA-140, RM-120, RM-lS0 Series Chassis (10" Rockford Clutch) .. R-ll0, R-120, R-130, R-lS0, RA-120, RA-140, RM-120, RM-lS0 Series Chassis with SD-220 Engine (11" Rockford Clutch with 9 Springs) . . . . R-160, RC-160, R-170 Series Chassis (11" Rockford Clutch with 12 Springs). R-170, RC-lS0, RF-170 Series Chassis and R-lS0, R-lS1, R-lS2, R-lS3, R-lS4 Chassis (12" Rockford Clutch with 12 Springs) . . . . . . . . . . . R-18S, R-lSS3, R-190, R-191, R-192,
R-194 (12 11 Rockford Clutch with IS
Springs) . . . . . . . . . . . . . . . R-190, R-200, R-210, RF-190, RF-210
Series Chassis (14" Rockford Clutch).
;; " 9
-Ii
i
~.
'll
RK-I0-B
Cushion
S/16" (CR-99)
l-S/S"
1-lS/16"
c z
[T1
3:
R-11A-I Cushion S/16 11 (CR-99) 1-11/16" 2"
::0
R-llA-l
Cushion
S/16" (CR-99)
1-11/16"
2"
~
(')
7'
U>
RR-12-12
Cushion
3/S" (CR-S4)
1-S3/64 11
2-13/64"
~ n
[T1
RK-12-1S
Cushion
3/S" (CR-84)
I-S3/64 11
2-13/64 11
------
RK-14-15
Solid
------
47/64 11 (CR-71)
2-S/32"
. . ....... . ..
til
ItIjr<
OQ
(l)
nO
t"1
Ploe:
0 I.>J>:C
z I-i
CLUTCH
Section A Page 4
RLINE MOTOR. TRUCK SERVICE

INNER HOLE PROVIDES HIGHER PEDAL PRESSURE
WITH LESS PEDAL TRAVEL
HI
III
.
r
OUTER HOLE PROVIDES LOWER PEDAL PRESSURE WITH GREATER PEDAL TRAVEL
---L
RELEASE BEARING SLEEVE
l
A30486
Fig. 3. Clutch Release Lever, Sleeve and Bearing.

For R.150, R.160, R170 series trucks, also R180, R181, R182, R1S3 and R.184 trucks.
r...11----- LUBRICATOR
ELEASE BEARING SLEEVE
OUTER HOlE PROVIDES LOWER PEDAL PRESSURE WITH GREATER PEDAL TRAVel --'"'\.
, ,
I
INNER HOlE PROVIDES '... r; ....".". PEDAL PRESSURE WITH LESS PEDAL TRAVEL ----..
RELEASE LEVER
A.30487
Fig. 4 Clutch Release Lever, Sleeve and Bearing.

For R.185 to RF210 trucks.
CLUTCHES
Section A
Page 1
CLUTCHES
Models RK-10B, R-llA-l, RK-12-12,RK-12-15, R-14-15, R-15-8
Fig. I (RK-IOB CLUTCH)
(a) Pressure plate to flywheel surface. . . . . . . . . . . . . . . . .
11/32 11
(b) Release lever to pressure plate surface. . . . . . . . . . . .. 1-15/32!T (c) Release lever to flywheel surface . . . . . . . . . . . . . . .. 1-13/16 11
H
G
Fig. 2 (R-11A-1 CLUTCH)
(a) Pressure plate to flywheel surface. . . . . . . . . . . . . . . . .
11/32"
(b) Release lever to pressure plate surface. . . . . . . . . . . .. 1-21/32"

(c) Release lever to flywheel surface . . . . . . . . . . . . . . . . .
PRINTED IN !JNITEO STATES OF AMERICA
2"
CLUTCHES Section A Page 2
Fig. 3 (RK-12-12, RK-12-15 CLUTCHES)
(a) Pressure plate to flywheel surface. . . . . . . . . . . . . . . . . (b) Release lever to pressure plate surface . . . . . . . . . . . . . . (c) Release lever to flywheel surface . . . . . . . . . . . . . .
3/8"
1-3/4"
2-1/8"
Fig.
ij (R-I~-15
CLUTCH)
(a) Pressure plate to flywheel surface (not shown). . . . . . . . .

(b) Release lever to pressure plate surface. . . . . . . . . . . ..
15/32 11 2-5/32" 2-5/8" 47/64"
* *-
(c) Release lever to flywheel surface (not shown) . . . . . . . . . (d) Cover plate mounting surface to pressure plate surface. . .
Not shown in illustration.
,:111&- ....
L
-III
~_
..
H
A-2JS75
Fig. 5 (R-15-8 CLUTCH)
* *
(a) Pressure plate to flywheel surface (not shown), , , , , , . , , (b) Release lever to pressure plate surface . . . . . . . . . . . . . (c) Release lever to flywheel surface (not shown) . . . . . . . . . (d) Cover plate mounting surface to pressure plate surface. . .
15/32" 2-9/32"
2-3/4" 1-9/32"
* - Not shown
in illustration.
LEGEND FOR FIGS. 1 TO 5 INCLUSIVE (A) Capscrew (for assembly purposes only)
(B) Adjusting screw lock nut
(C) Adjusting screw (D) Cover (E) Pressure plate (F) Pressure spring (G) Release lever spring
(H) Pivot block
(1) Rollers
(K) Release lever
(L) Release lever pin
(M) Drive lug

NOTE: The above clutch parts are referred to in the following serviCing
procedure under the deSignated letter. The servicing procedure, in gen
eral, is the same for all clutch assemblies.
PRINTt::b IN UNITEO STATES OF A..,(JIl:ICA

CLUTCH
capscrews holding the assembly compressed, remove clutch from flywheel by backing out the capscrews which hold it inplace. All capscrews should be backed out gradually to avoid damage to the clutch cover or back plate.
Description
These clutches are of the single dry-plate type, and release lever adjustments should not be requi red during the normal life of the clutch driven-plate facings. As pedal free-play is reduced by wear of the clutch driven-member facings, the correct amount of pedal free travel should be re sto red by means of the pedal adjust ment, which will also give the proper clearance between clutch release levers and the release bearing. It is extremely important to maintain free travel of the pedal at all times to avoid clutch slippage, and to protect throw-out bear ing. Whenever it is necessary to do any service work on the clutch, advantage should be taken of the opportunity to thoroughly recondition it. This is a comparatively short job and will assure satisfactory operation over a long period -of time, whereas failure to do this may neces sitate another tear-down within a short time.
Driven Member Assembly

The clutch driven member assembly should be carefully inspected. Facings showing con siderable wear, or facings that are rough or oil soaked, should be replaced. When installing new facings of the continu ous ring type, and in cases where two different thicknesses are used on each plate, the thick facing is installed on the pressure plate side. The thin facing is installed on flywheel side. Installation of clutch facings on the cushion type driven member differs from the other type in that each facing is attached to the discs sep arately and independently (Fig. 7 and 8).
Removal
When removing transmission for the pur pose of gaining access to the clutch, or for any other reason, extreme care should be taken to support the weight of the transmission until it is completely removed so that the main shaft splines will clear the driven member. Other wise, there is a possibility of distorting the driven member which will not permit a free release of the clutch.
~--""Rivets
Capscrew "A" For assemhly' only .
Fig. 7 - Solid type driven member, secures both linings to disc.
Each
rivet
~.J;;:;::;::?-:::::;::::::::::-~
Rivets securing thin facing Segment cushion type disc
capscrews
A-21578
Fig. 6 - Instal I capscrews "A" before removing clutch assembly. ~

The clutch pressure plate (E) is drilled and tapped so that three capscrews (A) (see specifications for sizes) with washers may be inserted through the cover plate (D), thereby holding the clutch assembly compressed when it is removed or installed (Fig. 6). With three
A-21573
Fig. 8 - Cushion type driven member. Half of the rivets hold thin facing and other half secure thick facing to disc
L-LlNE MOTOR TRUCK SERV1CE MANUAL

Clutch Overhauling Fixture
A clutch overhauling fixture is available (Fig. 9) and is adapted to the overhaul and ad justment of clutches used in International Motor Trucks. Complete instructions accompany the machine.
Fig. 11 - Spacer blocks are used when pressure plate extends below clutch cover.
(Figs. 10 and 11). Center clutch assembly over space plate. Draw fixture down to sur face plate being sure fixture arms are seated so as not to damage cover (Fig. 12). Compress the assembly lightly.
Fig. 9 - Placing clutch in Sf-990 fixture. Servicing the Clutch

NOTE: (Letter references in the text are those shown in Figs. 1 to 5.) The cover and pressure plate assembly is dismantled by placing specified spacer plate or spacer blocks on clutch overhaul machine
Fig. 12 - Draw clutch down with pulldown arms.

Remove the three capscrews (A) used to hold the assembly while removing it from fly wheel (Fig. 6). Loosen and remove lock nuts (B) from ad justing screws (C), Fig. 13. Screw adjusting screws (C) out of cover (D) turning screws clockwise three or four turns at a time while slightly releasing pre>ssure on backing plate. Repeat until pressure from the clutch pressure springs is relieved and adjusting screws (C) are free of cover (D). This procedure of grad ually releasing the assembly and backing out of the screws (C) must be followed in order to avoid damage to the lever assemblies (K). The clutch may then be fully re leased, afte r which all parts are readily dismantled for in spection and replacement if necessary. (Fig. 14.)
Fig. 10 -Use proper spacer plate, where needed,

PRINTP IN UNITEO STATES OF AMERJC,A.

Clutch spring tester (Fig. 15) or similar unit should be used for testing springs, (F). They may also be tested by comparison with new springs. Discard those not of same length.
spring Scale (pounds)
Fig. 13 - Remove adjusting screw lock nuts.
A-22fT2
Fig. 15 - Check spr j ngs on SE-1565 Spr i ng tester.

Release levers (K) that show considerable wear at the release bearing contact points as well as at the pivot points should be replaced. as should worn lever pins (L). The lever spring (G) should hold the lever adjusting screw (C) and pivot block (H) up firmly against the pivot points on the release levers. If this con dition does not exist on the old levers. it is sufficient reason for replacement with new lever assemblies.
Fig.
I~ -
Clutch cover removed.
Remove cotter keys from release lever pins (L) and remove pins and levers (K). A pressure plate (E) that is badly scored, checked or warped should be replaced, as it will not pe rform satisfactorily, and in addition, will damage the clutch driven member. If the clutch surface on the flywheel is not smooth, the flywheel should be removed, mounted in a lathe and smoothed with emery cloth using first a coarse cloth, finishing with a fine cloth. Where the surface is extremely rough, a light cut should be taken on the fly wheel with a lathe tool, finishing and polishing with emery cloth. Clutch pressure springs (F) that have had considerable service should be replaced, as it is possible that they may have lost their origi nal tension (see Specifications) and thus permit the clutch to slip under load. Springs that are discolored due to heat should always be re placed.
A-22175
Fi g. 16
When overhauling clutch assemblies, where no clutch fixture is available, the following procedure will be found helpful: The cover and pressure plate assembly is dismantled by placing it on a drill press or arbor press with supporting blocks of

wood or metal under pressure plate. (Fig. 16.) These blocks should not extend out beyond the outside edges of the pressure plate. (E). A bar is then placed across the top of the cover assembly "D" and the drill press or arbor press arm brought down to a point where the assembly is compressed slightly. From this point on, the same pro cedure can be followed as used with the special type clutch overhaul fixture pre viously explained.
Clutch Release Levers

Hardened-steel, disc-type rollers (J) used between the adjusting screw block (H) lever (K) which reduces operating friction relieves the stress on the adjusting screws are and and (C).
Assembling The Clutch (Using Clutch Overhaul Fixture)

Place the clutch pressure plate (E) with release levers assembled to plate on top of specified spacer plate (Fig. lO or Fig. 11). Installpressure springs (F) inposition on pres sure plate (Fig. 14). Place clutch cover or back plate springs, making sure that springs seated properly both above and below, the adjusting screw holes in cover are over the clutch lever adjusting screws (D) over (F) are and that directly (C).
Fig. 17 - Checking lever setting.

FOR SERVICE STATIONS NOT EQUIP PED WITH QVER'H.AUL FIXTURE, the follow ing procedure may be used: Place the pressure plate with release levers assembled on supporting blocks on drill or arbor press. From this point on, same procedure as outlined in the above paragraphs may be followed. The release levers (K) may be adjusted to correct setting as follows: Adjust the pressure plate in relation to the clutch cover as shown (Fig. 18). Use a straight edge across the cover plate sur face and, turning the capsc rews a small amount at a time, secure di:rnension given in specifications. Recheck this operation several times to assure accurate adjust ment.
Draw fixture down to clutch cover or back plate (D), Fig. 12, being sure fixture arms are seated so as not to damage cover. The assem bly can then be co:rnpressed slowly until the ~op unthreaded portion of each adjusting screw (C) can b~ guided by hand up through the tapped holes m cover plate (D). At this point care should be taken to see that both pressure plate (E) and cover (D) are lined up correctly, so as to permit free entry of the three drive lugs (M). Turn each adjusting screw (C) up into cover (D) approxi:rnately five turns at a ti:rne (turning screw driver counter clockwise) and after each five turns, co:rnpress the asse:rnbly a s:rnall amount. The release levers (K) :rnaynow be adjusted to the correct setting as follows:
.-
Turb capscrews
i~' adjusT
Clutch Release Lever Adjustments

The release levers (K) should be set to the di:rnensions shown in Figs. 1 to 5. Lever ad justing tool as shown in Fig. 17 can be used for accurate adjust:rnent of levers. It is very i:rn portant that all three levers be set exactly the sa:rne height. After levers are set to the cor rect height, the adjust:rnent lock nuts (B) are installed and tightened securely. Care should be taken not to upset the adjust:rnent when tight ening the lock nuts.
PRINTED IN UNITED STATts OF AMERiCA
cover
A-21580
Fig. 18

arrow is stamped on the outer flange of the clutch cover which indicates the HEAVY side of the clutch assembly The clutch should be assembled to the flywheel so that this mark is adjacent to the mark "L!I stamped on the fly wheel which indicates the LIGHT side. Fig. 20.
The release levers are adjusted in a man ner similar to that used when the "Clutch Fixture" is available. Place the clutch assembly on a flat surface and, with the adjusting screw lock nuts loose, adjust the levers to secure specified dimensions (Fig. 19). Recheck at each lever to assure accuracy.
Bolt clutch assembly to flywheel making sure that the marks on the flywheel and outer flange of clutch cover match as nearly as pos sible. This is important in order to maintain the correct balance of the flywheel and clutch assembly.
Fig. 19
Remove the three capscrews (A) holding the assembly compressed. The transmission stub shaft or aligning bar is also removed, as the driven-member assembly will now be held in position by the clutch pressure plate. Care should be exercised when installing the trans mission, so as not to permit the transmission to hang by the clutch shaft, which would bend the hub of clutch-driven member, creating mis alignment, with resultant clutch !ldrag ff
Installing Clutch
Figs. 21 to 25 inclusive illustrate clutch and control installation. When installing the clutch on flywheel in truck, care should be taken to see that the clutch driven-member is aligned properly by inserting a transmission stub shaft or aligning bar through the driven member splines and into pilot bearing. Have dampener mechanism of clutch driven member toward the transmis sion. IMPORTANT: An inspection mark or With transmission installed and floor boards in place, make correct pedal adjust ments. Do not adjust the clutch release levers, which were previously set to the correct height and require no further adjustment during the life of the clutch-driven plate facings. Pedal adjustments only are required to maintain the recommended amount of pedal free travel. The specified pedal clearance will assure proper clearance between the clutch release bearing and release levers. (Figs. 21 to 25 incl.)
NOTE: When installing the R-15-8 clutch on the International Continental Engine fly wheel, place the white paint marking on the clutch cover as close to the letter !ILl! (light side) on the flywheel as possible. The white dab of paint on these clutch covers indicates the heavy side of the clutch assembly.
Important
Oil and grease must be kept off the driven member facings. The clutch release bearing is lubricated at assembly and should require no further lubrication during the life of the clutch facings. If this bearing is removed for any reason it should be examined and replaced if it shows signs of lack of lubrication. The bearing and retaining sleeve are available as a unit and neither is furnished separately.
Fig. 20 - Showing use of aligning bar when assembling clutch to flywheel.
or shaft

Clutch Control Adjustment
Figs. 21 to 25 inclusive illustrate the assembly of the clutch control mechanism. The clutch pedal should have a specified amount of free movement before clutch pres sure is felt. (See Specifications or Figs. 21 to 25 inclusive). The clutch release bearing will just touch the clutch release levers when the clutch pedal is depressed the above amount. If clutch pedal free movement is 1" or less, adjustment is necessary to provide adequate bearing-to-lever clearance. As wear of the clutch facing takes place, the clutch release levers move outward. reduc ing the clearance between the clutch release levers and clutch release bearing. The ad justable yoke on clutch release rod provides means of adjusting the clearance.
Clutch Chatter
Clutch chatter cannot always be attributed to the type of lining being used {molded or woven}. It is generally chargeable to grease or oil on the clutch facing, the source of which may be: 1. Failure to remove anti-rust grease from the flywheel and pressure plate. 2. Excessive anti-rust grease in the cover plate assembly. When dismantling a clutch for service, the flywheel, pressure plate, and cover plate assembly should be thoroughly cleaned. If the clutch facings show evidence of lubricant, they should be replaced. It is impossible to remove oil or grease from clutch facings with solvents or by burning.
THE FOLLOWING PAGES - 10 to 14 inclusive

ILLUSTRATE CLUTCH INSTALLATIONS
PRINTED IN UNITED STA TS Of' AMERICA
CLUTCHES
Section A Page 10
Clutch pedal
For assembly purpose only
.~
E=!.'I
D :!
'\ il
I:,/A
I
.
I
Pul,' back
spnng
~-~_-d
Release bearing sleeve
8,4563
Fig. 21 - Control installation - L-IIO, l-120, L-130, L-150, L-153 Series.

A
I
I
D
11
11/32" 11-15/32"
1-13/16"
I 1 To 1-1/2
For assembly purpose only Release bearing sleeve
Adjusting yoke
84562
Fig. 22 - Control Installation - LM-120, LM-150.
c
!
11/32"
1-15/32" ll-13/16 t1
1 To 1-1/2"
PRINTED IN UNITED STA'tS OF' AMRICA
CLUTCHES
Section A Page 12
Clutch pedal
Adjustable yoke
Release sleeve
Release bearing
B.4564
Fig. 23 - Control Installation - L-160, L-163,
L-16~,
L-165, LC-160 Series.
,
A
11/32"
1-21/32"
2"
1 To 1-1/2"
CLUTCHES
Section A
Page 13
~D~
~, ,
MODELS L-170, L-173, L-174. L-175, LF-170
B
1
D 1 to 1-1/2"
11/32" 1-21/32"
2"
O/S FOR L-170 I SERIES L-180, 25/64" 1-3/4" L-183, L-184, L-185
Clutch pedal
2-1/8" 1 to 1-1/2"
Release bearing / Pul! back spnng
I
./
/j
o.
,
( --,IN,,I ' ",
n.\
i
I~'l-j ~ ~\c ~
Iii
II ..
Adjusting yoke
l,\
I
I)
\ -_---------- --..
----_.-_._--
, Il
I
Release bearing sleeve

'I
, ~
'-=-++=- /
-J
1E~ 1111 J_
I
'
k-~
)'
/1 I
For assembly purpose only
8-4561
Fig. 21t - Control Installation - l-170, l-173, l-171t, l-J75, LF-170, l-180, l- 183, l-161t, l-185 Series.
PRrNTEO IN UNITED ST4TES OF" AMERICA
CLUTCHES
Section A Page 14
Clutch pedal
'-------+--_.----
\..
Adjustable yoke
B.4691
Fig. 25 - Control Installation - L-190, L-193, L-200, L-20~, L-205, L-210, LF-210.
L-19~,
L-195, LF-190,
MODELS L-190, L-193, L-194
B
!
3/81! 1-3/4"2-1/8" 1 To 1-1/2"
O/S FOR L-190, L-194

15/32" 2-5/32" 2-5/8" 1 To 1-1/2" L-195, LF-190, L-200, L-204, L-205, L-210, LF-210
L~LINE
ELECTRICAL SYSTEM Index Page 1
ELECTRICAL SYSTEM GROUP
INDEX
Page Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1 to 6
SECTION itA"
Circuit Diagrams. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 to 8
SECTION "S"
Battery. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. I to 5
SECTION "C"
Ignition Coils. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1. Z.
SECTION "D"
Distributors
1 to 3
SECTION "E"
Generators " .. , .......... , ........ " " " .... , . , .... " .................................................. " .
11 Z
SECTION "F"
Headlights. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1 to 4
SECTION "G"
Horn . . . . . . . . . . . . . . . . . . . . . . . . . . .. '. . . . . . . . . . . . . . . . . . . . . . . . 1, Z.
SECTION "HI!
Regulators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 1 to 8
SECTION "I"
Spark Plugs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 1 to 4
SECTION
II
J"
1 to 4 .
Starting Motors (Cranking Motors) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PRINTED CN UNITED 5TATS 0,. AMERICA
("l
;;l
'I ;;::
~
>
F;
:x:
ELECTRICAL SPECIFICATIONS
R-110 THROUGH RF-210
(NOT RA-120, RA-140)
SD-220 SD-240 DR-llOOO19 BD-269 BD-282 RD-372

RD-406
RD-450
DR-ll02785
E~
'" v;
" 'i!.
[
ENGINE MODELS
-g
GENERATOR {Delco-Remy} . . . . . .
Field current {at 6 volts} amperes . . . . . . . . . . . . . . . . Cold output: Amperes . . . . . . . . . . . . . . . Volts . . . . . . . . . . . . . . . . . R.P.M . . . . . . . . . . . . . . . . .
Hot utput: o Amperes
{ Controlled} . . . by current ... Volts regulator .. R.P.M. Regulation. . . . . . . . . . . . . .
DR-ll02785
~
~
'f'
1.85-2.03
1.90-2.05
1.90-2.05
35 8 2650 45 8 2450 45 8 2450
r-.
'
Z ['I1
s::
~
:::0
?':
Ul
.................... . . . . . . . . . . . . . . . . . . ..
....................
-l .................... ....................
....................
n ~ . . . . . . . . . . . . . . . . . . . . ....................
....................
volt. and current volt. and current volt. and current
Brush tension {ounces} . . . . . . Bearing - commutator end . . . . . Bearing - drive end . . . . .' . . . .
28 bronze ball CW belt
28 bronze ball CW
28 bronze ball CW
n
['I1
Rot.ation {viewed from drive end}. Type of drive . . . . . . . . . . . . . .
en
'1:j
l'1
(1)
belt
belt
C. () ....
~'t--<:
en~
l'1
t'
..
'tl~en~
~.
(1)
..
o l'1> .... ~~t"'
J.-j ()
'U Clltll t'1

I "d
('0
QQ(\
N::!!t'1 ioi
8. ioi 0
I-<! I:"' CIl t'1
ELECTRICAL SPECIFICATIONS RA-120, RA-140

-
-_........
_._ __ _._
.. ........
......
__
~~~ ..... 0 .... ..... o > ; I:"'
............
E~GINE
MODEL
SD-220
GENERATOR (LOW SPEED CUT-IN) (Deleo - Remy). . . . . . . . . . . . . . . . . . . . . . . . . Field current (at 6 vOlts) amperes . . . . . . . . Cold output: Amperes . . . . . . . . . . . . . . . . . . . . . . Volts . . . . . . . . . . . . . . . . . . . . . . . . . Hot output:
DR-II05876 1.62-1.82
'
Z (T]
25
8.0
$::
A=peres { Controlled
Volts R.p.m. by current regulator
1 ............. J .............
...
..
'"
'"
'"
'" '" '" '" ,. ., . '" '"
. . . . . . . . . . . . .. .. .. ..
. '"
"
'" '"
'" '" ,. '" '"
'"
'"
'" '" '" ,.
..
'"
.. ..
.. .. .
'" ,.
'" '"
'"
.
..
" '"
,.
.. ..
,.
'" ,. '"
..
.. .. ..
'" '"
Regulation. . . . . . . . . . . . . . . . . . . . . . . . . Brush tension (ounces) . . . . . . . . . . . . . . . Bearing - commutator end . . . . . . . . . . . . . Bearing - drive end . . . . . . . . . . . . . . . . Rotation (viewed from drive end) . . . . . . . . . . . Type of drive . . . . . . . . . . . . . . . . . .
'" '" '"
. . ..
'"
..
,.
..
'" '"
'"
...
'" '"
. '"
"
" ~
C
Ul
-i
28
ball ball CW belt
---_._
....
~ ()
(T]
Em
~
'0
C
'"
ELECTRICAL SPECIFICATIONS R-110 THRU RF- 210 (NOT RA-120, RA-140)

ENGINE MODELS VOLTAGE REGULATOR (Delco Remy) . . . . . . . . . . . . . Amps . . . . . . . . . . . . . . . . . Type . . . . . . . . . . . . . . . . . . Current regulator: *Current setting-amps. (hot) .. Air gap. . . . . . . . . . . . . . Voltage regulator: *Voltage setting-volts. (hot) . . . Air gap . . . . . . . . . . . . . . Cutout relay: *Closing voltage-volts. (hot) .. Air gap. . . . . . . . . . . . . . . . Point opening. . . . . . . . . . . SD-220 SD-l40. BD-269 BD-282
-------
E
RD-371 RD-406 RD-450 DR-1118732 45
vibrating
47 .075" 7.4 .075" 6.4
.020"
.020"
45
~ '" v;
'E.
~ p
!
'0
DR-1118731 35 vibrating 38 .075" 7.4 .075" 6.4 .020" .020"
DR-1l18732 vibrating 47 .075" 7.4 .075" 6.4 .020" .020"
q
'f
Z [T1
:::
;;:f
()
ENGINE MODEL VOLTAGE REGULATOR-25 AMP. LOW SPEED CUT -IN (DelcoRem y) . . . . . . . . . . . . . . . Type . . . . . . . . . . . . . . . . . Current regulator: *Current setting-amps. (hot) .. Air gap. . . . . . . . . . . . . . . Voltage regulator: *Voltage setting-volts (hot) .. Air gap. . . . . . . . . . . . . . . .
. CI,ltout relay: *Closing voltage-volts (hot) .. Air gap. . . . . . . . . . . . . . . . Point opening. . . . . . . . . . .
SD-220 (RA-120, RA-140)
C 7':
Ul
DR-1118350 vibrating
25 .075" 7.2 .075"
() [T1
(f.l
6.4 .020" .020"
'1j
l'l t" l'l 8. 0 ....(f.l--> ... >-< .,

(Q
'tjC"l(f.l!:t1 11'11' H
OQ
::t., 0 (Qol'l>
!.;~t"
ELECTRICAL SPECIFICAfIONS
IQCIlCllM O\:lCltCllM
R-170 and RF-170 Series, R-180 thru 184, RC-180, 181, 182
ENGINE MODEL STARTING MOTOR (Delco-Remy) . . . . . . . . . Voltage. . . . . . . . . . . . . . . . . . . . . . . . . . Number of field coils . . . . . . . . . . . . . . . . . . Bearing - commutator end . . . . . . . . . . . . . . Bearing - center . . . . . . . . . . . . . . . . . . . . . Bearing - drive end . . . . . . . . . . . . . . . . Brush tension (ounces) . . . . . . . . . . . . . No-load test (with Solenoid or Magnetic Switch): Maximum amperes . . . . . . . . . . . . . . . . Volts . . . . . . . . . . . . . . . . . . . . . . R.p.m. approx . . . . . . . . . . . . . . . . . . .
Lock test: Maximum amperes . . . . . . . . . . . . . . . . . . Volts . . . . . . . . . . . . . . . . . . . . . . . . . Torque (lb. ft.) (min.) . . . . . . . . . . . . Rotation (viewed from drive end) . . . . . . . . . . .
ENGINE MODEL DISTRIBUTOR (Delco-Remy) . . . . . . . . . . . . . Initial setting (engine degrees) . . . . . . . . . . . BD-282 DR-II08009 6
4
cast iron bronze bronze 24-28
\ll'l:lt<t"
CIt
.r:.!:!M""
n. "" (')
~a::~ .... (') g > CII t"
l'
r Z [Tl
::
70 5.65
5500
~
til
~
570 3.15 13.5
CW
BD-282
DR-1112359 6 o B.T.C.
E~
ENGINE MODELS SD-220 SD-240 BD-269 RD-372 RD-406 RD-450 Cont. R-6602
COIL (Delco-Remy) . . . . . . . DR-11l5327 DR-1115327 DR-11l5327 DR-11l5327 DR-lllS327 DR-lllS327 DR-lllS2S1 DISTRIB UTOR . . . . . . DR-1l12355 DR-1l12355 DR-l112359 DR-1l12357 DR-1l12357 DR-11l23S7 Type . '" ............ '" . . . . . . . . . . . . . vac. auto vac. auto automatic automatic automatic automatic Cam angle . . . . . 31 _37 31 _37 35 35 35 35 Initial setting (engine degrees) 20 BTC 2 BTC 3 BTC r> BTC 5 BTC 5 BTC Vacuum advance (engine degrees) 15 15 none none none none Automatic advance (engine degrees) . . . . . . . 30 30 27 22 22 22 Total advance (engine degrees) . 32 32 30 27 27 27 selective none none none none Retard (engine degrees) . . . . . { selective 20 20 none none none none Contact point setting . . . . . .022" .022" .018-.024 .018-.024 .018-.024 .018-.024 Contact point pressure (ounces) . 17-21 17-21 17-21 17-21 17-21 17-21 Rotation (viewed from top) . . . CCW CCW CW CW CW CW Firing order . . . . . . . 153624 153624 153624 153624 153624 153624
4
automatic
z f11
3:
~
o
:;u -; :;u C
()
CCW
7': en
f11
*DISTRIBUTOR TEST DATA Start advance: Engine r.p.m . . . . . 500 500 0 Engine degrees . . . . 2 2 Intermediate advance: Engine r.p.m . . . 1800 1800 0 0 Engine degrees . . . . . 20 20 Macimum advance: Engine r.p.m . . . . 3000 3000 Engine degrees . . . . . . . . 30 30 Distributor vacuum control (De1co-Remy) . . . . . DR-1116049 DR-1116049
:;u
[Tl
400 0 1.5 1800 20 2700 0 27
500 0 1.5 1400 13 **3200 22
500 0 1.5 1400 0 13 **3200 22
500 0 1.5 1400 0 13 **3200 22
< n
3: :J>
r
:J>
.. .
.. '"
. ..
'"
..
. ...
'"
..
'"
'"
..
'" .. '"
. ..
"d
00
* Distributor Test Stand figures will be one-half of these specifications.

** Test Stand r.p.m. only. For maximum engine r.p.m. see "Engine Section."
M
M
t-'
8. 00...., () ......
1:J~oo~ Il>~l-:l() OQoM>
~(Il;::"
.... ><: .-,
rD::J!:>,t-'
ENGINE MODELS GENERATOR-50 AMP. (Delco- Remy) . . . . . . . . Field current (at 6 volts) amperes . . . . . . . . Cold output: Amperes. Volts . . . R.p.m . . Hot output:- AmpereS}Controlled {. Volts by current R.p.m. regulator. volt. and Regulation. . . . . { curren t Brush tension (ounces) . . 25 Bearing - commutator end. ball Bearing - drive end . . . . ball Rotation (viewed from driveend). CW Type of drive. . . . . . . . belt GENERATOR (LOW SPEED CUT IN) (Delco-Remy) . . Field current (at 6 volts) amperes . . Cold output: Amperes. Volts . . . R.p.m . . Hot output: AmpereS) Controlled {. Volts by current R.p.m. regulator. Regulation. . . . . .
I
11
RD-406 RD-450 Cont. R-6602
(1)
OQ(1)(flM
UHIl M 1\1'0 >-<t""
SD-220
SD-240
BD-269
RD-372
N~M...,
<+ ....
8. ..., C'l
~l1::::o ......
C'l
DR-ll06757 I DR-ll06757I DR-ll06757I DR-ll06757I DR-ll06757 I DR-ll06757 I DR-ll06822 1.70-1.95 50 7.5 1410
g > ID t""
1. 70-1.95
50 7.5 1410
1.70-l.95 50
7.5
1410
1. 70-1.95
50 7.5 1410
1.70-1.95 50 7.5 1410
1.70-1.95
50 7.5 1410 50
7.5
[T1
t z
volt. and current 25 ball ball CW belt
volt. and current 25 ball

ball CW belt
volt. and current 25

ball ball
CW belt
volt. and current
~
--l
3:
::0
::0 C
()
belt
7':
{J)
[T1
DR-ll06758 I DR-ll06758 1. 70-1.95 40 7.5 1165 1.70-1.95 40 7.5 1165
::0
[T1
< n
3:
z c r
Brush tension (ounces) Bearing - commutator end . . Bearing - drive end . . . . . Rotation (viewed from drive end). Type of drive . . . . . . . . .
volt. and current 20

bali ball CW
belt
volt. and} current

20 ball
ball
CW
belt
ENGINE MODELS GENERATOR-30 AMP. (Delco Remy) . . . . . . . . Field current (at 6 volts) amperes. . ..... Cold output:
Amperes. Volts R.p.m . . . Hot output:Amperes} Controlled Volts by current '" R.p.m. regulator Regulation. . . . . . SD-220 SD-240 BD-269 RD-372 RD-406 RD-450 Cont. R-6602
DR-1102714 I DR-II02714 I DR-II027141 DR-II02714 I DR-I1027141 DR-II02714 1.75-1.90 30 8 1750 1.75-1.90 30 8 1750 1.75-1.90 30 8 1750 1.75-1.90 30 8 1750 1.75-1.90 30 8 1750 1. 75-1.90 30
8 1750
o -l o ;;.0
c
()
A
Ul
[Tl
Sci
1"
;;.0
current 24-28 Brush tension (ounces) . . bronze Bearing - commutator end . ball Bearing - drive end . . CW Rotation (viewed from drive end). belt of drive . . . . . . . .
{ v~it" ~~d
volt. and current 24-28 bronze ball
volt. and current 24-28 bronze

ball
[Tl
< n
z r
en
CW
belt
CW
belt
CW
belt
CW
belt
CW
belt
"0
(!)
M
M
t""'
(lQOM>
wm;::..
PI::ti-l()
'""en'-'! ..... ....: '-:l 'U ~ en?:!
8.
()
(!)i:I!7t"'
ENGINE MODELS VOLTAGE REGULATOR-30 AMP. (Delco-Remy) . . . . . . . . Type . . . . . . . . . . . . . . Current regulator: *Current setting-amps. (hot) Air gap. . . . . . . . . . . . . V oltage regula tor: *Voltage setting-volts (hot) . Air gap. . . . . . . . . . . Cutout relay: *Closing voltage-volts (hot). Air gap. . . . Point opening. . . . . SD-220 SD-240 BD-269 RD-372 RD-406 RD-450 Cont. R-6602
()'Q
trl (/) (f.!I."l fl) '"0 >< r (l) (/) M
(l)
8. '"'l () *,"::l!M'"'l
<+ .....
DR-IllB303 IDR-IllB303 IDR-IllB303 I DR-IllB303 I DR-IllB303 I DR-IllB303 vibrating vibrating vibrating vibrating vibrating vibrating 30 .075" 7.4 075" 6.4 020" .020" 30 .075" 7.4 075" 6.4 .020" .020 11 30 .075" 7.4 .075" 6.4 020" .020" 30 .075" 7.4 .075" 6.4 .020" 020" 30 .075" 7.4 .075" 6.4 020" .020" 30
.075"
7.4 .075" 6.4 .020" .020"
~~::o .....
()
g > m r
[T1
t z
VOLTAGE REGULATOR-50 AMP. HIGH OUTPUT (Delco-Remy). DR-1118333 IDR-IllB333 IDR-llIB333 IDR-1l18333 IDR-ll1B333 I DR-1l18333 I DR-ll1B368 Type . . . . . . . . . . . . . . vibrating vibrating vibrating vibrating vibrating vibrating vibrating Current regulator: Current setting-amps. (hot) 50 50 50 50 50 50 50 Air gap. . . . . . . . . . . . . .OB2" OB 2" .OB2" .OB2" .082" 082" .075" Voltage regulator: *Voltage setting-volts (hot) . 7.4 7.4 7.4 7.4 7.4 7.4 14.3 Air gap. . . . . . . . . . . . .075" .075" 07 5" 07 511 .075" .075" 075" Cutout relay: *Closing oltage-volts (hot). v 6.4 6.4 6.4 6.4 6.4 6.4 12.B Air gap. . . . . .020" 020" .020" .020" .020" .020" .020" Point opening. . . . . . . . . . .020" .020" .020" .020" 020" .020" . 020"
:::0 :::0 C
-I
7':
(f)
()
n
[T1
<
VOLTAGE REGULATOR-40 AMP. LOW SPEED CUTIN (DelcoRemy) . . . . . . . . . . . Type . . . . . . . . . . . . . . . . Current regulator: *Current setting-amps. (hot) . Air gap, . . . . . . . . . . . . . Vol tage re gulator: Voltage setting-volts (hot) .
Air gap. . . . . . .
Cutout relay: *Closing oltage-volts (hot)~ v Air gap. . . . Point opening. . , . . . . . . .
DR-1118366 IDR-II1B366 vibrating vibrating 40 .075" 7.4 07 5" 6.4 .020" 020" 40 .075" 7.4 .075" 6.4
.020"
.020"
z c r
* Current and voltage
specifications apply only at operating temperature. Operating temperature shall be assumed to exist after not less than 15 minutes of continuous operation with a charge rate of B-I0 amperes.
ENGINE MOD.ELS SPARK PLUGS AC } "standard" { proChampion heavy ducAuto-Lite service tion AC } "hot" { . Champion mod~rate . Auto-Lite service . AC } "standard" { . Champion heavy Auto-Lite service . AC } "cold" Champion severe Auto-Lite service Spark plug size Spark plug gap . 44 Corn 44 Corn. 45 Corn. 43 Corn. 43 Corn. 43 Corn. SD-220 SD-240 BD-269 RD-372 RD-406 RD-450 Cont. R-6602
J-7
AN5 45 Corn.
J-7
AN5 45 Corn.
J-8
AN7 45 Corn.
J-6
AN5 44 Corn.
J-6
AN5 44 Corn.
J-6
AN5 44 Corn.
82 Corn. 5 Corn. BT4
J-8
AN7 44 Corn.
J-8
AN7 44 Corn.
J-8
AN7 45 Corn.
J-7
AN7 43 Corn.
J-7
AN7 43 Corn.
J-7
AN7 43 Corn. 82 Corn. 5 Corn. BT4
J-7
AN5 43 Corn.
J-7
AN5 43 Corn.
J-8
AN7 44 Corn.
J-6
AN5 43 Corn.
J-6
AN5 43 Corn.
J-6
AN5
43 Corn.
r: c z
[T1
..... ...... . . . .. ..
3:
J-6
AN5 14 mm .028-.032
J-6
AN5 14 mm .028-.032
J-7 AN5
14 rnrn .028-.032
J-6
AN5 14 mm .028-.032
J-6
AN5 14 mm .028-.032
J-6
AN5 14 mm .028-.032 18 mm
.023-.027
o -l o ;0
;0
(')
-l
C
A
STARTING MOTOR (Delco-Remy) I DR-ll07074I DR-II070741 DR-ll07967I DR-ll082171 DR-II090041 DR-ll09004 Voltage. . . . . . . . . . . . . . . 6 6 6 I 6 6 6 Number of field coils . . . . 2 2 4 4 6 6 Bearing - commutator end . cast iron cast iron cast iron cast iron cast iron cast iron Bearing - center . . . . cast iron cast iron cast iron Bearing - drive end . . . . bronze bronze bronze bronze bronze bronze Brush tension (ounces) . . 24-28 24-28 24-28 24-28 36-40 36-40 No-load test (with Solenoid or Magnetic Switch): Maximum amperes . 75 75 60 70 70 70 Volts . . . . . . . . . 5.7 5.7 5.0 5.0 5.7 5.7 R.p.m. approx. . . . 5000 5000 6000 3500 2200 2200 Lock test: Maximum amperes. 525 525 600 600 600 600 Volts. . . . . . . . . 3.4 3.4 3.0 3.0 3.0 3.0 Torque (lb.ft.)(min.) . 12 12 15 22 35 35 Rotation (viewed from drive end). CW CW CW CW CW CW MAGNETIC SWITCH (DelcoRemy) . . . . . . . . . . "1 Current consumption (at 6 volts). DR-1465 5.7-7.0 DR-1465 5.7-7.0 DR-1465 5.7-7.0 DR-1465 5.7-7.0 DR-1465 5.7-7.0 DR-1465 5.7-7.0
12
(f)
bronze
bronze
36-40
[T1
;0
(') [T1
<
z
65 11.4 6000 725 5.0 44 CW
'1:J
:t> :t>
C
$:
(Jl
'U
M
t"'
Cl
n PlPl(Jl .... OQ ~ >-3 Cl

roOM~
~(Jl>-3
....
><::o
lTI~g:t"'
~CJ)CJ)1:'1
OQ(1)CJ)1:'1 (1) 8.1-3(1 0--:::-:1:'11-3
I 'U
-< t:-'
ENGINE MODELS HEADLIGHT SEALED-BEAM UNIT (Guide) . . . . . . . . IGNlTION SWITCH (Delco-Rern.y). LAMPS (BULBS) Stop and tail light bulb: Voltage . . . . Candle power . . . Contact. . . . Parking light bulb: Voltage. . . . . . Candle power . . Contact. . . . . . Instrurn.ent light bulb:-' Voltage . . . Candle power . . . Contact. . . . . . Beam. Indicator bulb: Voltage . . . . Candle power . . . Contact. . . . . . . SD-220 SD-240 BD-269 RD-372 RD-406 RD-450 Cont. R-6602
~ ~
r
....
R~~ (1
924791 1116465
924791 1116465
924791 1116465
924791 1116465
924791 1116465
924791 1116465
5930856 1116465
[Tl
t z
6-8 21-3 DC 6-8 3 SC 6-8

2
6-8 21-3 DC
6-8 3 SC 6-8
2
6-8 21-3 DC 6-8 3 SC 6-8

2
6-8 21-3 DC 6-8 3 SC 6-8 2 SC 6-8

1
6-8 21-3 DC 6-8 3 SC 6-8

2
6-8 21-3 DC 6-8 3 SC 6-8

2
12-16 21-6
DC 12-16 3 SC 12-16 1.5 SC 12-16
1
s:
@
::;0
-;
::;0
C 7':
[Tl
fJJ
SC 6-8
1
SC 6-8 1 SC
SC 6-8 1 SC
SC 6-8 1 SC
SC 6-8
1
::;0
n [Tl
SC
SC
SC
SC
s:
> z > r
c
STORAGE BATTERY Type (Auto-Lite) . 2H-I05 2H-I05 2H-135R 4H-152R 4H-152R 4H-152R 4H-152R Specific gravity: Fully charged at. 1.280-1.290 11.280-1.290 11.280-1.290 11.280-1.290 11.280-1.290 11.280-1.290 11.280-1.290 Recharge at. . . . . 1.225 1.225 1.225 1.225 1.225 1.225 1.225
Voltage . . . . . .
6 6 6 6 6 6 6
Arn.peres hours at 20-hour rate. 105 105
135 152 152 152 I 152 Arn.peres-20 rn.inute rate. 133 133 170 180 180 180 180 Terrn.inal grounded . positive positive positive positive positive positive positive
Q
'J>
"
Fi :t
Cable Color or
~
"0
r=eh4~eratOrficl.r:::-.~ 8 :""'Toenerator ann.
"'"
Description
Em
::c
[l"J
Vi
1
'g
'!1.
!!
q
'{'
Battery
,.....1-
.-_" I
~
~14
... 1
~~ I 1"::\ ............ Starting push switch "and R163

~ (U) (ll)""--, . . }R.H 0.1. _ \yindshield ~~:tl====='l'-(~ '<, b IlgmtIon switch :.- >'1"'-- Wlper motor
Fuol
I
" " \\ \ I .
:~ ~~Hom relaY-R.H.n
F~ Modol,
Rl53
r'
........
Z
~
.--_+--!til
Junction I block /
"-H--LI. /,
(20)
Temp' Cab" ground!
""1,-yJ ! rTi\ r"'-- ---:B ~ & ~~. / i Windshi Id 3 ~T ';;;-iil';Jl! ~~l--I "'--"",wiper swi~ch 2 or P"'I""'" / CirclntF:ltG-Circuit /bre~e!S~:;~;l--breaker I' or,' b~t.1 t
1
0 ...., 0
@i ___L
I
u,h< ""tch I
I
'~Ig:t'"
Bat. coil
I~{
L;;+====::J~
_ '"
A~m. P, A ----I ----- ,. / 1...-----"' I w~_\.9I"t-_.....J _....1"'"Fuel .I / .% I
---;- l=. /Inott.:': "",k"~

/ Dome light
~S'-t~-:::.:1-::::JI - ij--- -lnstr. L__ light I --High

/
switch Dome light
;a
c:: ()
B D
E
::c
1:2
1
en
F
G
16 14
16 16
Horn~ 26
__
7tJ r:;X 1/ Y"/('''
14 g a . ! J o Y \:Z)
/~ r:;;;,. -~
..
\
---~-/i light L.H.D. --Stop switch ~ ,..>!:!!J

,--:>,
.J rV~i~:!~h"~nd ignition
~ ()
[l"J
"
:;
C %
" !I
" " ~ 0 " ~
0
"
" ~ m
'(z6) ~
f4Y
L.H.D.
'---1~,.a~..::.::...----'
Bat \::..J
I \
1
\ ',\
Fuel..:::-;-Trailer taillight
\i[]nectors
\ 22
.......... T
~6 .1;......
.. ad gao 21
Enlatged view A.A
8TI66
R egulator
Hom
bu""""
16. 14 :::;
14 ga.: R ..110 t o R,,165 nghthd. It. ,,165 ~ft hd. It.
~:l~ :;~ 130 left hd. IL
railer stop light
l"l I:"' l"l

Ul .n ()
t-cl~...c:~
II> ....
ll>"'l-j
Fig. I Wiring circuit diagram. (RllO, R.120, R1lO, R150, R160 series trucks)
~M~
.....
..... ~s;:1:"'
'UtntnM
Parking light
ID--.
J
,@16 ga.,
/~
OQ::l.tnM ~ .... 1-3 C"l NgMI-3

I Cab ground
'\
Ckcui.tNo.
Lott.o
IlIC11~t"'
rtf;
Junction block
}<@16
ga1 ~
"I~I"
I
Headlight ~" '"
rYFi:"
gao
Starting motor '\
Generator
--::-In
Light switch
----0
. . . -.-
<E<
~~~ J/~Ignition
I
]//@
//~
Circuit breaker
-2 4
I
;..-!5:::c ....
;..
t"'
Cable Gauge
Cable Color or Description Generator aeld Generator arm. Regulator to ammeter Ammeter feed Ignition switch feed Ignition switch to Ig. nltlon coU Starting Light switch feed Dimmer switch feed High beam feed High beam indicator High beam head. light leads Low beam head. light leads Low beam feed Parking light leads Parking light feed Tail.light Stop light Connector 10 relay HOJ'n and horn re lay feeds Horn and stop light feed Instrumenl feed FuelgBuge Temperature gauge 011 pressure gauge Dome light Instrument lights Ignition call to dte tributor Headlight ground Battery ground Engine ground Cab ground BB!:'&'cable Horn utton to con nector
C"l
16 8 8 8 12 16 16 12 12 1204 16 16 16 14t16 16 1608 16 16 16 1204 12 16 18 18 18 18 16 16 14 4 3 12 1 16
12 14 15 16 17 17 17 18
20 20
11
tis<
lw
~+k~'
f
11/1111
/Y 1
?A+<:=::~~M
Bmm 'n&aOX
1 -
J/
and starting switch
18
[T1
~.
~ r
1.,/ 4.0)
--' 40 /
21 22 25 26 26
11kJ.1
I Hom
-' .
27 30 33 36 38 40 80 91
C
B
:;0
~
C
;1
() ~
Fuel I
''(26)
I I I
I I-I-T
,...-_ _ _ _ _ _..11"'"
J- ~II -_ I
I
~Hom button Engine ground

StoP, light sWitch
.I~II' ~ ,,~"'@
UJ
D E H
0)
Dome light
Fuel
~ -
() [T1
~
21)
A
""'I
Stop
-~
1=
~
I
OOi?Tt
8-7181
Fig. 2 Wiring circuit diagram. (RM.l20. RM.150 series trucks)
E-
9
@
'" <Ii
/
1 1
I
a.II @),! Battery 17 18,

j
/' " /'
Circuit No. Cable 'r Index Gauge Letter 1 ' 16

-~--r-
Cable Color or Description field
Em
::0
=:-.
"r>.
!
~
"'II~
11
l
g'
\V~II'
Starting motor
F
/'
x.v
C" Ircult breaker
'12
-5 11
14 15 16 17
17 17
18 18 20 20 21
,/
Junction block /.:
Generator
)..:::J
/'4 or H, 3 or T ,\ 2 or P "", , 1 or bat.\ \, ,
/
L18 ga,@' ~,/
114 gao
Temperature
D' ~IIJ~[==~~~~ switch >l, "Light

~
40 ....
22
26
~~.....
fl\.--.-.. .
0.....
" Distributor
33 -=
"'\ ~ r/
,
\\
cab} ground
"'P"
_1- Speedometer ~ I H'gh bea m I - indicator light . ~

.....
-_~
.1-.. . Instrument light .@

1
26
" 33-'
36 38
27 30
~
o
3::
::0
r-.
--:::=:::---
~--I' ~ P I
h
Oil preS8ure_~ Dimmer switch- - -
Amm0 r-T"l--Instr. light
-----70
40 71 80 91 A
d
~
~
8'
D
E F
C
14 16 16
(i8)___
~'
~~
Hom Hom I relay
I..

'--t-'+'~-:rir-_+-H-_..!.I..:::J ~
,
/f Dom~ ~ te1~~ ~~'~; :ht

~l--Fuel
rJg\
light sWitch
G H
1
----:Ell
L--\
II
I \
\
Connector'
-~----~
\
~~~~~~~~,:itch
\\
)Sin
\
g
\\ ~1 16 a.
\\
7;JI (TUI
Stop
~~,
~ I ~~ l
I12 gao II 14 gao I ~ ~ ~ F'-=\-J'" Regulator (zO) '(z6) li6) Gen. Bat, tIl
Fig, 3. Wiring circuit diagram. (RC.l60 series trucks)
\ ', "'
'J
~,
"" \ Hom button
F~l
E la d n rge View A.A \ Trailer stop light 'Trailer tail light
8-7179
~ .... '":1 't1 n ,",,'.D
oooon
I:-l l"" I:-l
~gl:-l~
1ll1t.~H
w>!S:l""
'ijCf.lCf.lt<J
Cable Gauge Cable Color
OQ
"",gt<J.,
1lIn>><t-' ~Cf.lM n> ...'., ()
>-~~
> t-'
()
..-,-____s.:a~ng push switch )-.,!If JR. R. D. l r-r--lS~~~~~~tCh

II ' l---h
: I ,1--.1
L I ""'-.
For Models R.173

and R183
Windshield /' /' /' wiper switch Circuit --breaker - -Speedometer - -Instrument light - - High beam indicator - -Instr. light '-'''/ Dome light switch Dome light Starting and ignition
switch- L.R.D.
Stop light switch
I
-@
/"'.
I
I
Windshield wiper motor
l' r Z [T1
d
:::0
E:"
~
n
~
G H p 14
16
l~
I ........ a.un..
PUbU DUUVU
..'1 .. ..
() [T1
Stop
,J
" 'Trailer stop light "Trailer tail light
Tail Enlarged view
A.A
Stop and tail light

BTlIl1
Fig. 4 - Wiring circuit diagram. (R-170, RF-170, R-180 series trucks-not R-185)
Em
a
'I :;:
>
/")
:<'
E~
Cable Color
:I:
~
~
r;;
~ 3
Q
~
Light light
AI I
I
J
Park Head[l~'II@r.1
/
!!.
'g
91 //~
I
17
18
...
I;
i/,~atte~1I
; B
"-'V ~
;/
;~:~,
/ 4 or H,
--
" ~
a
Sl 'f
i2o)
[18~1 -I
~j ~
I.
130rT\\ , 2 or \\
p,\ \
r'
[T]
Junction block
118 116
ga.@--i I
ga.~---t1_
.,.--
1
Distribu~
II
or bat. \ \ \
I'\\~i
114
ga'-:J L (D-- [L CD-Dimmer switch ~IJ

Hom
relaY '!.1
~
()
s::
~
~
B
D
11~r 20
\
~
Hom.
E F
n
. . .,.
1~
Junction block
"
Enlarged view
__9 _ H
p
1""&i:"IU~ _ "L"""""'''''''''''''! u... _... L"".__

~L
[T]
.."
i
AA
c:
" z
z
button
\ \
._W-~", \
Light
Park
F. Gen. Bat.
Regulator
\,
'\C' . breaker and trcwt terminal block assembly
B-T/SO
14
l:"l l:"l C/l ." (") ro .. 1-3
t'"
"tl~><~ ill ..... 00 ....

(lQol-3(")
Fig. 5. Wiring circuit diagram. (RC.180 series trucks)
ro::ll:'1>
...,,>E:t'"
I.lQ ~ (I) III ..... .,
"tJ tlltll trl lUn><t"'
t::l
C'l
O"gtrl.,
>E:~
t"'
Fuel
';p r
[T1
3:
(i7)-- ~
Distributor
I (iO}. ___
1
;;:J
~
r.n
R
~
~
Engine ground
8-7168
(R.185 truck and R190, RF.190, R.200, R210, RF210 series trucks)
Ell
a
r
lI:
PARK
g
~ ....
LIGHt
E
20 I
I
f
;;
r-------- ---~
rI
E.
'0
~ 0
iii
:Ji
GENERATOR
' ~---------t----+-+---~ SWITCH.RHO I I I: . \,;"-------------~.

I
(
I I I
I
I
I
r --,_
r'
STARTPUSH
SWITCHRHO
B I IGNITION
\~ )
~.
Ii
If
JUNCTION BLOCK
I
I
-'"'
P ! 16ilh:Jf11i Iii (
!
~
~,:HJSW(TCH "
LIGHTER
=:a r
[T']
~
ENGINE GROUND
()
~
~ til
~
TRAILER STOP LIGHT TRAILER TAil LIGHT
() [T']
."Z
:II
" " z
:j
" ~
.z
~
I:<J
8-1090
..
en .... rft ell
I:<J 0 ...:j
t'
... "
"tI::!.....:l:;Q
.
~
ii
:II
~gtzl~
Fig. 7 - Wiring circuit diagram, 12Volt System. (R1aS to R210, RF190 and RF210 trucks)
t ... ~ ....
...J>il::t'
ELECTRICAL SYSTEM Section A Page 1
CIRCUIT DIAGRAMS
Electrical circuits for the various L-Line trucks are illustrated on following pages. Cables are protected wherever necessary by 100m or conduit and by rubber grommets, to prevent chafing where contact is made with the chassis, cab or body, Cables are also securely clipped at important points and connectors are used to facilitate inspection and servicing. All electrical connections must be kept tight and clean. tions, there is a key to the diagram which con tains pertinent information as to circuit number and cable gauge.
Individual Cable Replacement

It is recognized that replacement of one or more individual cables may be necessary and that complete harness replacement may be im practical. For this reason, the chart on each circuit diagram specifies the proper-gauge cable to be used and which can be made up locally from bulk stock.
Circuit Numbers And Circuit Names Wiring Harness Individual Cable Circuit
Identification
Wiring harness cable circuit identification has been established by (UNumber Codingll) im printing numerals at regular intervals along the individual cables, except for short cables which are numbered only at the ends. The prime purpose of cable identification is to facilitate wiring harness installation since, in harness, generally only the extreme ends of the indivi dual cables are visible. The accompanying circuit numbered list (from No. 1 to 124) itemizes circuit numerals used on L-Line. Wherever a particular circuit is used on a vehicle, the identification numeral for that circuit will always be the same. For example, the generator field circuit cable will consistently be Circuit No.1; the generator armature circuit will always be Circuit No.2, etc. (see list). In the same manner, if a circuit is not used on a vehicle, the numeral for that circuit will not be used. For example, vehicles not having a 24-volt radio-feed cable will not have a circuit No. 48 in the harness. Circuit numbers on the list for which no circuit description is given are not presently used by International and these circuits have been reserved for possible future assignment. Circuit Nos, 28 to 31, inclusive, each per tain to fuel tank-to-receiver unit circuits. Because of the variety of possible combinations for these hook-ups, reference should be made to the illustrations for proper connection of cables, (Fig. 1)
cmCUIT NO.
CIRCUIT NAME
1. Generator field circuit. 2. Generator armature circuit. 3. Generator ground circuit. 4. Generator regulator to ammeter or shunt. 5. Ammeter (or shunt) to starter switch. 6. Battery to starting motor switch mounted on starting motor. 7. Battery ground (including master switch if in this circuit). 8. Shunt to ammeter positive. Shunt to ammeter negative.
9',
10. Circuit breaker, common feed to any point fed from regulator (Bat). 11. Ignition switch feed (or magneto ground). 12. Ignition switch to ignition coil (or booster switch to booster coil). 13. Magneto ground. 14, Magnetic starting motor switch to push button switch to feed. 15. Main light switch feed. 16. Light switch (HT) to service headlight or dimmer switch. 17. Dimmer switch to upper beam and to beam indicator. 18. Dimmer switch to lower beaIl'l.
Circuit Diagrams
Wiring circuit diagrams are illustrated in the owner's and driver's manuals and in the service manuals. With each of these illustraPRINTED IN UNITED STATES OF AMERICA

46. 12 - Volt radio master switch). 47. Slip ring feed. 48. 24 Volt radio feed. circuit (including radio
19. Light switch (Bod) to blackout driving lamp. including resistor. 20. Light switch (BHT) to parking lamps or marker light. 21. Light switch (R) or (HT) on blackout switch to service tail light. 22. Light switch (H) or (S) on blackout switch to service stop light. 23. Light switch (BS) to blackout stop light.
49. Receptacle. Auxiliary power outlet, posi tive lead. 50. Receptacle, Auxiliary power outlet, nega tive lead. 51.
24. Light switch (BHT) to blackout tail light. 25. Horn switch (including feed) to horn (or horn relay). 26. Horn relay feed and horn relay to horn. 54. Fuel cut-off circuit. 27. Instruments feed (instruments with polar ity). 28. 29. Fuel gauge sender to receiver - 30. See illustrations Figure 1. 31. 32. Oil level gauge sender to receiver. 33. Water (and oil) temperature gauge sender to receive r. 34. Low engine oil pressure warning light cir cuit (including feed). 35. High water temperature warning light cir cuit (including feed). 36. Oil pressure gauge sender to receiver. 37. Outlet socket or junction block. 38. Dome light circuit (including breaker and switch). 39. Map light circuit. 40. Instrument light circuit. 41. Starting motor to battery (-) (series paral lel switch hook-up). 42. Series parallel switch (B+) to. battery (+). 43. Series parallel switch (A-) to battery (-). 44. Series parallel switch to ground. 45. Series parallel switch motor. (B-) to starting 55. Flame primer low tension circuit. 56. Flame primer high tension circuit. 57. Instrument panel ground. 58. Compass light circuit. 59. Cab (or hull) ventilating fan circuit. 60. 61. Auxiliary generator field. 62. Auxiliary generator armature. 63. Auxiliary generator ground. 64. Auxiliary generator regulator to battery (including heater transfer switch). 65. Auxiliary generator starter relay circuit (including switch and feed). 66. Auxiliary generator starter to transfer switch (including starter or relay). 67. Emergency stop switch ground. 68. Battery interconnecting cables. 69. Resistor to ground coupling. 70. Regulator ground. 71. Windshield wiper ci rcuit. 72. Low transmission oil pressure indicator, circuit, with feed. 73. Radio terminal box to ground. 74. Series parallel switch to solenoid relay. terminal on trailer 52. 6-Volt tap on taillight dropping resistor to tail light. 53. Electric brake control circuit.
L-UNE MOTOR TRUCK SERVlCE MANUAL

75. Stop switch circuit (SW to SS on blackout SW). 76. Fuel pump control feed. 77. Fuel pump switch to fuel pump (left side). 78. Fuel pump switch to fuel pump (right side). 103. Cigar lighter. 79. Fuel gauge sender ground.
100. Tachometer transmitter to ground. 101. Defroster switch including feed. to defroster motor
102. Heater switch to heater motor including feed.
104. Fog light switch to fog light including feed. 80. Ignition coil to distributor. 105. Tractor light (Back-up). 81. Battery to starting motor switch (or term. block) including master switch. 82. Starting motor switch (or term. block) to starting motor. 83. Blackout light switch (TT) to tail connec tion on trailer receptacle. 34. Blackout light switch (SS) to stop light con nection on trailer receptacle. 85. Low air pressure indicator buzzer (or light). 86. Ground on series parallel switch to am meter (including circuit breaker). 87. Spotlight circuit for trucks and wreckers. 88. Winch torque limiter control. 89. Automatic choke. 90. Trailer receptacle to ground. 91. Headlight to ground. 92. Parking light to ground. 93. Starting motor relay to ground. 94. Starting motor relay auxiliary grounding circuit. 95. Tail light to ground. 96. Speedometer sender feed. 97. Tachometer transmitter feed. 98. Tachometer transmitter tachometer positi~e (+). positive (+) to 123. Overdrive solenoid to ignition coil (includ ing kickdown switch). 124. Overdrive solenoid to battery (including relay feed). 106. Carburetor idle fuel shut-off valve. 107. Marker or identification light circuit. 108. Clearance light circuit. 109. Mico brake lock circuit. 110. Fuell gauge switch (C) to ground safety tanks). (dual
Ill. Lockoff solenoid valve to switch (including feed). 112.Auxiliary ammeter to ground-negative. 113. 6- Volt radio circuit (including ratio master switch). 114. Direction signal, left turn-front. 115. Direction signal, left turn-rear. 116. Direction signal, right turn-front. 117. Direction signal, right turn-rear. 118. Direction signal, feed circuit. 119. Voltage divider ground. 120. Voltage divider feed or instrument resis tor feed. 121.
Overdriv~
relay to ignition switch.
122. Overdrive relay to overdrive governor (including kickdown and overdrive switch).
99. Tachometer transmitter negative (-) to tachometer negative (-).
f'~IN1'D
IN UNITED STATES OF' AMt"RlcA
30
Underskirt tank
30
30 29
30 29
Underskirt tank and right side auxiliary tank
[?
~
Right side tank
29
J
~
30 !29
Underskirt tank and dual auxiliary tanks
28
Left side tank
28
~.
30
~
Rear end tank
31
D
Left side tank and right side auxiliary tank
0 Rec.
30 28
Underskirt tank and
left side auxiliary tank
gauge switch
,30
28
A-22921
Fig. I - Fuel tank to receiver circuits. Because of the variety of possible combinations for these hook-ups, reference should be made to the above chart for proper connection of cables.
~
~
@
I
Fuel gauge sender unit
Circuit No. or Cable Index Gauge Letter
Cabl.Color or
Description
~r
1 2 4 12 14 16 16 17 17 17 18 18
11
14 8 8 8 14 14 14 10 12 12 14 16 14 16 14 16 14 14
10
" z
C
, ,
:;
~
~
/@
1
'1
Generator
Starting
motor
"
~
~
4ga.
Engine

~
ii
/-@ }
1':~!:/16ga.
' '."f
Oil
--, Junction block

light
20 20 21 22 26 26 27 27 29
12 14 16 16 16 16 16 16 14 14 14 16 0 3 12 0 16 14 14 16 16
33 36
40
30
Generator field Generator arm Regulator to am meter Ammeterf_d Ignition switch feed Ignition switch to ig nition coil Startinq Light switch f ....d Dimmer switch f.ed Hiqh beam feed High beam h ..ad li;tht lead.. Hig beam indiea tor Low beam f..ed Low b .. am h .. ad li~htl"ad.. P .... ing feed Parking light lead. Taillight Stop light Horn and stop light feed Horn !lind horn relay fseds Inlltrument feed Instrument feed Fuel gauge Fualgauge Temperature gauge
[T1
t z
$
80
71
A
Oil pressure gauge Instrument light.. Wiper switch feed

Ignition coil to di.,... tributor
:::0 -J :::0 C
o -J o
o
7':
91
J/~@llJ@ JJ~~~~v'III6'" I,,-~-;~

Fuel gauge sender unit
/@
light
B C D E F
Headlight ground Natural with circuit letter "A" or black Battery ground
Engine ground
(J)
~
[T1
Cab ground Battery cable Natural with circuit letter uF" or red
Instrument
bUB
(=)
<
G H
bar
Horn push button

Fuel gauge ground Natural with circuit Jetter "p" or ~n
x""]
~
CD
~Regulator
d..,Sto p
~
Enlarged view X-X
z c r
M l' M Ul 0 roUlt-J
8-4737
Fig. 2 - Circuit Diagram - L-IIO Series to L-IBO Series inclusive (Hot "Metro")
Pl ..... Ul ...... OllOt-JO ro::lM>
'O~>-<!!:d
<.}'I>-~l'
't1CflCflM ()QOCfl
O'-;l
Il>(l)O-<t""
(l)~!-:JM
o ..... () '-J !-:J
>:;:;:: () > t""
[T1
t z
$::
:::0 -1 :::0 C
(")
~
CJ)
[T1
:::0
<
sender unit Battery ground strap/

/
(") [T1
// - - - ---Stop light switch Magnetic starting switch

"'--
"'-,,-
Junction block /
z
c
r
$::
Horn relay
Head light
8-4696
Fig. 3 - Diagram showing location of various electrical units. clusive (Hot "Metro").
l-IIO Series to l-J80 Series in
Circuitj No, or Cabl..

Ind..x Gauge Letter'
Cabl.. Color or
D..cription Generator field Generator arm ReGulator to am .. meter Ammeterf.ed Ignition switch fe.d Ignlllon switch to ig nition coil Starling Light ;'witch f.ed Dimmer switch fe.d High beam f...d High beam h.ad lJ.~ht l.ad. Hig beam indic. tor Low b.am fe.d Low b.am h.ad l!~ht I..ad. Par ing feed Parking light l.ads Taillight Stop light Horn and stop light f .... d Horn and horn ...~ lay f.eds Instrument feed Instrument f .... d Fu.lgauq. Fu.lgauqe Temperature qauQ. Oil preu... 9au9. Instrument light. Wiper switch fe.d Ignition coil to dis tributor
Hsadlight~ound
Fuelgualle sender un~@:
(])
4 or H\
1 2 4 5 11 12 14 15 16
17
14 8 8 8 14 14 14 10 12 12 14 16 14 16 14 16 14 14 10 12 14 16 16 16 16 16 16 14 14 14 16 0 3 12
, , z ;:
" z
:;
fl.-''---,-' I I I
=
~
Generator
3 or T\ \ 2 or
\
p\\ \\ "f' 1
Windshield wiper motor
c z
" m "
o ~
co
@
Junction block
I \
1 or Bat \ \[\1
17
17 18 18
14 ~a 16 ga, 16 ga,
~ " ;;
)1)
~
Distributor
I I
1
\Circuit breaker
20 20 21 22 26 26 27 27 28 29 33 36
I
r r
[T1
,0
$: 0 ~ 0 :;u
" Instrument
Enl:ine I:round \ light T ach'ometer Dimmer switch Circuit breaker and terminal block assembly------
71 80 91
A B C D
40
:;u
C 0
~
I
Junction block
E
F
1~
c!.!'
G H ,J P
14 14 16 16
Natural wi circuit letter"A" or black Batt.ry ground Engine ground Ca qround Battary cable Natural with circuit l.tter "F" or red lnatrument bu. bar Horn puah button Fuel gauge qround Natural with circuit I_tter "P" or qre,_n
en [T1 :;u
0 [T1
<
~ ~~~1 ~
I 1\
I
14 ga, 16 ga,
14 ga,
&6l
Horn'K' 12
1\
1
I
I
I
I
I
~R\ X"I
z r
M t:"' M UlUl O ro >-l 'U ;?"< ::0 III ..... Ul ..... OQo>-lO ro::lM::t>
-.I::t>~t"'
$:
1--1
Tail Stop Enlarged
view X'X
"l'
14 p.
Regulator
.......
Fig.
- Circuit Diagram - l-190 Series And Up.
't1
OQOtJl
tJltJl M 1l)(1)t4t"
Windshield wiper motor Dash panel
\\
\
\
Windshield wiper switch _-Fuel gauge sender unit /, Instrument light ~~ (R. H. tank)
I
oogM~
m::t.~~
CIgar
Ignition switch___
\
I
-I - fI - . ,- ----- I .--
j.
I,,, Pi
. . To tatlltght f) Ammeter gauge . ,~. and stop light If! // Temperature gauge ~"'~. \
I /"
I ,Speedometer II
'", <.~
>~~
()
',"~~... ~ '-" "I(,l'~
.~
'~
Light swltch----..2>. I _-->~ ~ Beam indicator light~ >Cab ground strap-----...... --Junction block\ Temperature gauge sender unit--.....l Ignition coil----J
"- ,/,..-/'
I -- , ---1
///
. I .
I1
~/-;//
//// ___ /
\
,.1111 Ii
,I \ - --~--Starting push switch \\ ~J-. '\' ...... Dome lIght Instrument lights
~~-'..:.."---- Tachometer ~ .
'~ __ --
-Fuel / . gauge ___ Oil pressure gauge
,'" \\ . ~\ ~,/~ .
[Tl
t z
\\Circuit breaker and terminal '.\ block assembly \Voltage and current regulator
I
I
I
I
o --l o
;0 ;0
s:
~ ~.\~l~~~--~----Battery cable
Generator Engine ground strap- ,
/
/ /
~n
~,
'" /1@;> II j : / \.( ~J ~I~. V ~', ,I .~ /;:J'e
I~~
Fuel gauge {ender unit (L. H. tank) _---Battery ground strap _--Battery
--l
C 7:::
{j)
[Tl
;0
[Tl
~;:'''\
/ '
~{d~IV I
1
I
\ I
< n
/ '-....Y" " \ Stop light sWitch \ Oil pressure gauge "' . . . " \ 0 ' 't 1 ' " llunler SWI c 1 \ '" " sen d er unit \\J unctIOn bl oc k . "'", . . .'''Magnetic starting switch , . . . Startmg motor . ' ht H eadlIg
'- " "
s: z c r
/ Parking light
8-4868
Fig. 5 - Diagram showing location of various electrical units - L-190 And Up.
ELECTRICAL SYSTEM Section B Page 1
BATTERY
Storage Battery Equipment
Present production trucks are equipped with Auto-Lite batteries. The following chart is the key to the code datings found on Auto-Lite batteries used in International Motor Trucks of later manufac ture: Month January February March April May June July August September October November December Month Symbol Year Year Symbol
Code Dating
Each Auto-Lite Battery bears a shipping code stamped on one button of one cell connec tor of the battery. This button is indicated as nA" in Fig. 1.
o
(IT)
;-----+- Button-A
-i---...".
1 2 3
000
e
Standard assembly Reversed assembly
4 5 6 7
8 9 10 11 12
1949 1950 1951 1952 1953 1954 1955 1956 1957 1958
9
0 1 2
3
4 5
6
7 8
00:=--=00
End to .end assembly center cell
Atmospheric Temperature Affects Battery Capacity

The specific gravity of the electrolyte (distilled water and acid solution) must be maintained at 1.225 to 1.250 and the level of the solution should be at the star level in cell cov ers. A fully charged battery has a specific gravity of 1.280-1.290 at 80 degrees (F.). To eliminate the possibility of harmful sulfation of plates, a battery with a specific' gravity of 1,225 or less should be recharged to 1.280-1.290 at 80 degrees (F.) battery temper ature. The following chart shows the effect of atmospheric temperature on the capacity of a battery:
Positive button
6-volt assembly.
A-16015
Positive button - cell adjacent to positive terminal cell- ll-volt assembly.
Fig. I
i
I
I L .J
r-"
r-'I I
,__ ...t
Month
Fi g. 2
Year
A-.23439
State of Charge Full Full Full Full Full Full
Temperature (F.)
80 degrees above 0
0
Percentage Capacity
100
The code date will 'be found stamped on the positive connecter button on the cell adjacent to the positive terminal cell. See Fig. 2, In the first row are two symbols: the first is the month, the second is the year of shipment, for example - "8-9" which decodes August - 1949. In the third row, the second space is used to indicate whether the battery was built "dry" or 'wet." If there is no symbol in the space the battery was built wet. If the space contains a letter "yn - the unit was built dry. If the letter "Y" is encircled thus - the battery was built dry and made wet before shipment.
PRINTEO iN UNfTED STATES OF AMERICA
60 degrees above 0 0 o 40 degree s above 0 0 20 degrees above 0 Zero degrees o 20 degrees below 0
88 75 62 45 20
Specific Gravity Affects Freezing Point of Electrolyte

Specific gravity of the electrolyte deter mines the temperature at which a battery will be harmed or damaged by freezing.

the specific gravity readings of each cell, date of delivery, truck model and chassis serial number, and the name of the purchaser. The card will then be filed in a manner similar to the Customer's Record Card. If the battery is delivered in a truck being transferred in another District, the battery record card shall accompany the battery and shall be continued by the receiving branch.
The following chart gives the freezing point of battery electrolyte at given specific gravities: Electrolyte Specific Gravity 1.280 1.220 1.210
Freezing Point (F.) 90 degrees below 0
30 degrees below 0 0 20 degrees below 0
Battery Maintenance
The Ft. Wayne and Springfield factories are exercising every care in the handling and rotation of batteries to assure the delivery of a fresh and fully charged battery with each and every truck delivered to the territory. The territory must also follow this prac tice of rotation, using the oldest batteries first as determined by the code datings stamped on the center cell connector button. To facilitate truck movement in and around the District or Warehouse, a service battery should be prepared having long cables and clip ends.
1.100 1.000
20 degrees above 0 32 degrees above 0
o
o
Battery Record Card, Form CTS-7

The Form CTS-7 Battery Record Card is the record or history of each battery received and shipped. The card has spaces provided for allnecessary information pertaining to the bat tery. One of these record cards must be main tained for each battery and it should reveal the complete history of the unit while in your pos session. Upon receipt of a shipment of trucks from one of the factories or from another Branch, the batteries must be removed immediately and battery record cards filled out for each battery. THERE MUST BE NO DEVIATION FROM THIS PRAC TICE. The date received, battery type, code marking, truck model, and chassis serial num ber must be entered on a separate record card for each battery. The specific gravity of each cell must be recorded on the card under TEST RECORD. The date and the inspectorrs initials should also be shown in the space provided. Any bat tery showing a specific gravity reading of less than 1.225 must be placed on the charging line and brought up to 1.280-1.290 at 80 degrees (F.) (battery temperature). Subsequent inspections of the battery shall be made every thirty days and the specific gravity readings recorded, and distilled water added if necessary. This procedUre shall fol low during the stay of the battery in your stock. Upon delivery of battery in a truck, the record card shall be completed by recording
Battery Recharging
Suitable and adequate equipment for battery charging is available through the Motor Truck Service Section, Chicago Office. _ The general procedure in battery charging
is as outlined:
1. With vent plugs in place, wash the top of the battery if necessary, using a solution of water and common baking soda. Rinse with clear water. 2. Remove vent plugs from each cell. 3. Fill the battery cells with pure distilled water to star level in cell covers. 4. Connect battery to the charger unit in series, connecting the terminal outlet from the supply positive of the first battery. Connect .-=--"'-_-.. terminal of the first battery terminal of the second so on through the number of batteries being charged. (Do not attempt to exceed the capacity of the battery charging equipment in the number of batteries to be charged at one and the same time.) The last battery m.ust have its negative terminal connected to the negative outlet of the charging unit.
5. Adjust the charging rate in amperes to the lowest normal charge rate of~.tl(!~E:1allest size battery according to the following chart.

Batteries should remain on charge for a period of time sufficient to obtain normal volt age and specific gravity readings of each cell. The required length of time will vary from 12 to 48 hours, depending upon the state of dis charge of the battery at the time it was placed on the charging line. Type of Battery 2H-I05, 2H-I05R 2H-120, 2H-120R 2H-135R 3H-136R 4H-152R I 8T-200 Volts 6 6 6 No. of Plates 15 17 19 17 19 25 7 8 I 9 8 9 12 Normal Charge Rate Amperes Amperes Amperes Amperes Amperes Amperes
Battery Not to Blame for Failure When

Conditions Adverse
It has been shown that temperature plays an important part in affecting the capacity of a battery, and that the colder the temperature the lower the battery capacity. Bearing this in mind, it will be seen that a fully charged battery is only partially capable at subzero tempera tures. This fact, coupled with the condition in which many engines are found, brings about complaints regarding the size, quality, and construction of the standard equipment battery. There are times when it is necessary to increase the size of the battery or starting motor, but such action should not be considered a "cure-all" for hard starting complaints during winter months. Even when special equipment of this nature is installed, it is still essential to: 1. Use a lubricating oil with the correct body for Winter Service. 2. Maintain distributer points in good condi tion and properly spaced. 3. Have clean and properly spaced spark plug electrodes. 4. Have good compression in the engine. 5. Maintain all joints and connections between the carburetor, manifolds, and engine in a gas-tight condition. 6. Ascertain that the carburetor choke valve is operating properly. 7. Determine that the engine is well grounded and that the ground straps are fastened to contacts.
6
6 12
Temperature readings should be taken frequently to prevent the electrolyte tempera ture exceeding 110 degrees (F.) at any time. Should the temperature rise higher than 110 degrees (F.), the charging should be discontin ued and the electrolyte allowed to cool. The charging of the battery may then, and only then, be continued. 6. Cell voltage is determined by a normal electrolyte temperature of 80 degrees (F.). Voltage readings are to be taken while the battery is on charge at the normal rate as specified in the foregoing chart. The cell voltage of a fully charged battery on charge at the normal rate should read as follows: 80 degrees (F.) - Voltage between 2.5 and 2.6 volts Temp. 100 degrees (F.) - Voltage between 2.4 and 2.6 volts Temp. 11 0 degrees (F.) - Voltage between 2.35 and 2.55 volts A battery is fully charged when the cell voltage values are as shown in above table and there is no further rise in voltage over a period of two hours. 7. Add water as necessary, disconnect batteries from the charging line, replace vent plugs, wash the tops of the batteries, and place in attachment room. Temp.
Battery Warranties and Manufacturers! Policy

Storage batteries used in International Motor Trucks are limited to a free repair or replacement warranty of 90 days against defec tive material and workmanship, beginning on the date the battery is placed in service. In accordance with this arrangement, service adjustments after 90 days are based on miles of service or - which ever occurs first. tioned for there are a customer will attain the limit of miles of service prior to the time limit set forth. In such cases, the adjustment will be made on the :miles of service and not on the time limit. Auto-Lite Batteries, whether installed as factory equipment by the Inte rnational Har vester Company or sold as replacements to
Excessive Evaporation of Electrolyte Indicates Overcharging

When excessive evaporation of the elec trolyte is experienced, you may be sure that it is an indication that the battery is being over charged. Necessity for too frequent battery re charging may indicate that the battery is.being undercharged.
P~'NTED
IN UNITED STATS OF AMERICA

are withbattery warranties, and the manufacturer's policy. There should be no departure from the instructions as outlined. It must be remembered that while the manufacturer is under certain obligations in accordance with the warranty policy of the batteries, we too, are not absolved of obligation to the manufacturer to do our part of the arrangement and policy.
It is felt that of all the instructions outlined herein that the fo1lowing are the most impor tant and no excuse can be accepted for depar ture from them:
International Harvester Truck owners, subject to adjustment as outlined below.
Factory equipment or replacement bat teries are adjusted according to the following table:
Service Adjustment Chart

Battery Equipment Type 2H-l05,2H-105R 2H-120,2H-lZOR 2H-135R 3H-136R 4H-!52R 8T-ZOO
I
i
Mileage Adjustment. 15,000 18,000 21,000 18,000 18 000 24,000
Time Adjustment
7-1/2 Months 9 Months 10-112 Months 9 Months 9 Months 8 Months
Complaints on Battery Performance

Any complaints pertaining to battery per formance should be referred to the nearest Auto-Lite Service Station.
1. REMOVAL OF ALL BATTERIES FROM THE TRUCKS AT THE TIME THEY ~~.RE RECEIVED AT THE BRANCH, AND KEEPING THEM IN THE ATTACHMENT ROOM OR BATTERY ROOM UNTIL' THE TIME OF DELIVERY.
2. INSPECTION OF BATTERIES EVERY THIR TY DAYS, AND MAINT AINING THEM AT THE PROPER WATER LEVEL AND AT THE PROPER SPECIFIC GRAV ITY READINGS. 3. KEEPING OF FULL AND COMPLETE RECORDS OF THE BATTERY ON THE BATTERY RECORD CARD, FORM CTS-7. 4. PROPER AND CONSISTENT ROTATION OF BATTERIES IN STOCK, DELIVERING THE OLDEST BATTERIES FIRST. 5. INSTRUCTIONS TO THE CUSTOMERS IN THE PROPER CARE OF THE BAT TERY AND A CAREFUL STUDY OF THE REQUIREMENTS ON THE BATTERY AND CORREC TIONS FOR SAME IN THE CUSTOMER'S TRUCK.
Complaints on Service Facilities

Complaints on service facilities of Auto Lite distributors must be referred to the Sales Department, Motor Truck Service Division, Chicago Office. Accompany complaint with all details concerning the battery and the truck from which it was removed. The matter will be handled with the manufacturer from the Chicago Office and not by the District direct.
Batteries Older Than Four Months at Time of

Delivery
Motor Truck Service Bulletin No. 82, 1931, pertained to batteries which were on hand and which were older than four months according to code dating. :That bulletin advised that these batteries shoula' be delivered in proper rotation but that they should be properly identified by stamping the letters "IHCII on the center ce1l connector button. Battery Record Cards, Form C TS-7, were to be notated with this information. Customer Record Cards were to bear a nota tion to the effect that the battery was past the four months' code dating. PROPER AND CONSISTENT ROTATION OF BATTERIES IN STOCK MUST BE FOL LOWED, AND THE OLDEST BATTERIES ACCORDING TO CODE DA TINGS DELIVERED FIRST.
General Instructions
Do not add anything other than distilled water or drinking water which is colorless, tasteless, and odorless to a storage battery. The use of patent electrolytes or battery IIdopes ll are injurious and void the guarantee. Use a strong solution of soda and hot water for removing terminal corrosion and cleaning the battery. To prevent corrosion apply vase line or cup grease to the terminals.
Moist Uncharged Storage Batteries

To prepare a battery for service which has been shipped dry, all cells should be filled to 3/8" above the tops of the spacers with the electrolyte specific gravity of 1.345. CAUTION! NEVER POUR WATER INTO SULPHURIC ACID.
Strict Adherence to Instructions Necessary

All persons who have occasion to handle batteries or battery transactions should thor oughlyfamiliarize themselves with the instruc tions pertaining to maintenance of batteries,
L-UNE MOTOR TRUCK SERVICE MA:.lUAL

Important Instructions
To prepare 1.345. specific gravity electro lyte from full-strength sulphuric acid stir con stantly while adding one volume of 1.835 acid to two volumes of water. THIS MUST BE DONE VERY SLOWLY AS A GREAT DEAL OF HEAT IS GENERATED. Use only glass or earthenware containers for storing and for mixing the acid. In some localities acid can be purchased already mixed to 1.345 specific gravity.
tions. Adjust electrolyte specific gravity by adding distilled water to weaken and 1.400 spe cific gravity acid to strengthen. When adjusting electrolyte, charge the battery for one hour before' taking a final reading. At the end of 52 hours the cell voltage of the battery while on charge at the proper rate should be between 2.5 and 2,7 volts at 80 0 F. Replace vent plugs, wash externally to remove traces of acid. and dry. Battery is now ready for service.
Table 1
Warm or Tropical Climate Filling Acid Sp. Bau, Gr. me Final Adjustment Sp. Bau, Gr. me 1.225 26.4
Cold Climate Filling Acid Sp. BauGr. me 1.345 3.7 Final Adjustment Sp. BauGr. me
INSTALLA TION OF CABLES

When making replacement of original bat tery cables, starting motor cables or other wires utilizing protective loom or grommets. it is essential that the service cable be equipped with the same type loom or grommet protection as was removed on the replaced cable or wire. Cables that are replaced without proper loom protection create a fire hazard. The wiring circuits on new vehicles are closely checked and approved by Underwriter Companies, there fore. the original circuits should be maintained both as to location and protective devices.
1.290 31.5 1.245 28.5
A tropical climate is that in which the temperature never falls below the freezing point of water (32 0 F.) (00 C.). Place the battery on charge at the ampere rate given below: Battery Equipment Type 2H-I05R 2H-120R 2H-135R 3H-136R 4H-152R 8T 200 Ampere 7 8 9 8 9 12
The loom or grommet is placed on cables for the purpose of safeguarding against chafing or cutting through the insulation at points where the cables contact the chassis. When replacing cables on custome rs trucks or when making sales of cables, make certain that protective loom or proper grommets are provided where required. The storage battery can deliver only what the battery cables are able to carry to the elec trical system. The battery cannot operate effi ciently if it has to overcome the resistance of a worn-out, corroded or undersize cable. Faulty battery performance may indicate cable trouble.
For converting dry batteries to wet, use a constant rate charger. Do not use a constant potential charger. The total initial charge must be for 52 hours. However, should the temperature of the electrolyte while on charge reach ll5 F. 0 (46 C.). discontinue the charge and allow the battery to cool. Then resume charging. The electrolyte at the end of 52 hours' charge with battery temperature at 80 0 F. (26.7 0 C.) should be at the value given in Table 1. Make corrections for temperature, when necessary, according to previous direcPAINTED IN UNITED $TATES OF AM'IIJICA
Care should be taken when installing a ca ble terminal. It should never be hammered into place. To do so may drive some of the active material from the battery plates into the bottom of the battery container or crack the cell cover. Also some metal may be sheared from the post, making it too small for good contact when the next replacement is necessary. The best prac-. tice is to pry the jaws of the terminal apart be fore slipping it over the post.
ELECTRICAL SYSTEM Section C Page 1
IGNITION COILS
Sealing nipple High tension terminal
gaskets
Sealing-==:....:....~tc!.
A-22612
Fig. I - Schematic wIring diagramofthe primary circuit of an ignition system.

DELCO-REMY MODEL 1115327
IGNITION COIL
The Delco-Remy (Model 1115327) Ignition Coil is oil-filled and hermetically sealed to prevent the entrance of moisture The high tension terminal is protected by a bakelite in sulator which has high resistance to leakage across its surface andis not damaged by leakage which might occur. The coil should be mounted vertically with the high tension terminalddown or horizontally with primary terminals in same horizontal plane. Make sure the coil is mounted so the case is grounded and that the leads are tightly connected to the coil terminals.
Coil ..,,"4'-....::,
A-22552
Fig. 2 - Cutaway view of oil filled coil.
If the coil is defective it must be replaced. since the coil can not be repaired. But before a coil is discarded, it should be carefully checked on a good te ster to determine that it is actually defective.
Construction and Operation

The ignition coil is a pulse transformer that transforms or ":up the low battery or generator voltage to the high voltage necessary to jump the gaps at the spark plugs in the en gine cylinders. This voltage may reach as much as 20,000 volts. The ignition coil contains three essential parts; a primary winding consisting of a few hundred turns of relatively heavy wire, a sec ondary winding consisting of many thousand
PRINTED IN UNtTEO STATES OF" AMERICA
turns of very fine wire, and laminated soft iron which serves to concentrate the magnetic field. The primary winding is assembled around the outside of the secondary winding, and the lam inated iron is distributed so that one portion serves as a core for the windings and the re mainder as'a shell around the entire subassem bly. This subassembly is then placed in the coil case and the remaining space nearly filled with insulating compound or oil, and the coil cap assembled into place.
Fig. 3 illustrates a heavy-duty ignition coil used on motor-coach, truck and marine applications. This coil also is hermetically sealed against the entrance of ai r 0 r moisture and is oil filled for greater insulation protec tion. The fins cast in the one-piece case plus the oil filling permits improved heat radiation which is a factor in efficient ignition coil per formance.
ELECTRICAL SYSTEM Section C Page 2

Coil Service
Ignition coils do not normally require any service except to keep all terminals and con nections clean and tight. In addition, the coil should be kept reasonable clean, but it must not be subjected to stearn cleaning or similar cleaning methods which may cause moisture to enter the coil unless it is of the hermetically sealed type. Rubber nipples on the high voltage terminals are valuable in preventing Ittracingtl or leakage of current across exposed surfaces.
If poor ignition performance is obtained and the coil is suspected of being the cause, the coil may be tested on the truck or it may be removed for the test.
High tension terminal
Coil winding
Fig. 3 - Cutaway view of heavy duty oil-filled colI. Coil case utilizes fins to aid in cool jng for better ign it ion col I performance.
ELECTRICAL SYSTEM Section D 1
DISTRIBUTORS
Rotor
Cap
Terminal
Breaker cam
A-226J8
Fig. 2 - Sectional view of distributor.

distributor directs the high voltage surge through the distributor rotor, cap and high ten sion wiring to the spark plug which is ready to fire. There are thus two separate circuits through the ignition distributor. One of these is the priITlary circuit which includes the dis tributor contact points and condenser. The other is the secondary or high tension circuit which includes the distributor cap and rotor.
Fig. I - Ignition system circuit. lationship of various units.
Showing re
IGNITION DISTRIBUTORS
The ignition systeITl (Fig. l) consists of the ignition coil, condenser, ignition distributor, ignition switch, low and high tension wiring, spark plugs, and a source of electrical energy (battery or generator). The ignition systeITl has the function of producing high voltage surges and directing theITl to the spark plugs in the engine cylinders. The sparks ITlust be tiITled to appear at the plugs at the correct instant near the end of the COITl pression stroke with relation to piston position. The spark ignites the fuel-air ITlixture under cOITlpression so that the power stroke follows in the engine.
DELCO-REMY DISTRIBUTOR
The Delco-ReITlY Distributors used on BD and RD engines are full autoITlatic units with centrifugal advance ITlechanisITl. The SD engine uses a distributor having the vacuuITl-autoITlatic ITlechanisITl.
Function of Distributor
The distributor has three jobs. First, it opens and closes the low tension circuit between the source of electrical energy and the ignition coil so that the priITlary winding is supplied with interITlittent surges of current. Each surge of current builds up a ITlagnetic field in the coil. The distributor then opens its circuit so that the ITlagnetic field will collapse and cause the coil to produce a high voltage surge. The second job that the distributor has is to tiITle these surges with regard to the engine require ITlents. This is accoITlplished by the centrifugal and vaCUUITl advance ITlechanisITl. Third, the
PRINTED IN UNITED STATES Of' AMIi:RfCA
Fig. 3 - Full automatic distributor. moved.
Cover re
ELECTRICAL SYSTEM Section D Page 2

meter is recommended to check the point open ing of used points. When necessary to check and adjust point opening with a feeler gauge proceed as follows: Rotate breaker cam until breaker lever rubbing block is on the high point of the cam lobe thus giving the maximum point opening. Loosen the clamp screw holding the contact support and adjust point opening by turning the eccentric screw in the contact support. Tighten clamp screw, check with gauge after tightening clamp sc rew. THE ONTAC T POINTS SHOULD BE CLEANED BEFORE ADJUSTING IF THEY HAVE BEEN IN SERV ICE. The cam or contact angle is the angle in degrees of cam rotation through which the points remain closed. This angle increases with decreased point opening. As the rubbing block of a new breaker arm wears in, rounding the corners of the rubbing surface, the contact angle increases. CONTACT POINT PRESSURE - Must fall within the limits given. Weak tension will cause point chatter and ignition miss at high speed, while excessive tension will cause undue wear of the contact points, cam and rubbing block. USE OF DISTRIBUTOR TEST FIXTURE The distributor test fixture accurately checks cam angle, spark advance and synchronization on distributors removed from the car. It will also show excessive distributor shaft eccen tricity as indicated by variation in synchron ization. After a distributor has been repaired, the calibration of the centrifugal automatic mecha nism -should be checked. Proper engine per formance cannot be obtained unless the centrifugal curve is within the limits specified for the particular engine. THE CONDENSER - Four factors affect condenser performance and each factor must be considered in making any condenser tests. BREAKDOWN is a failure of the insulating material, a direct short between the metallic elements of the condenser. This prevents any condenser action. LOW INSULATION RESIST ANCE or leakage prevents the condenser from holding a charge. A condenser with low insu lation resistance is said to be Ifweak. II All condensers are subject to leakage, which up to a certain limit is not objectionable. When it is considered that the ignition condenserpe:J;'forms its function in approximately 1/12,000 of a second, it can be seen that leakage can be large without detrimental effects. It must be consid ered, however, in any condenser test. HIGH SERIES resistance is excessive resistance in the condenser circuit due to broken strands in
Distributor Maintenance
LUBRICATION - Do not remove pipe plug in distributor oil reservoir. This reservoir back of the shaft bushing is filled with light engine oil and sealed before the unit is shipped. The supply of oil is sufficient to last for 25,000 miles of operation under normal conditions. Thus the plug need not be removed oftener than every 25,000 miles (or at time of overhaul) for lubrication except when unusual heat or other operating conditions are experienced. Grade SAE #20 oil should be added when needed. Seal the plug with sealing compound that will hold against oil. A trace of high melting point ball-bearing grease should be placed on the breaker cam every 1000 miles. Every 5000 miles put one drop of light engine oil on the breaker lever pivot and a few drops on the felt wick under the rotor.
Inspection
The cap should be removed at regular in tervals and the contact points, rotor, and cap examined. Check the high tension wiring for frayed or damaged insulation and poor connec tionsat the cap or plugs. Replace if necessary. Replace the cap or rotor if they are cracked or show carbonized paths indicating the secondary current is leaking to ground over the surface of the material. CONTACT POINTS - That are burned or pitted should be replaced or dressed with a clean, fine -cut contact file. The file should not be used on other metals and should not be al lowed to become greasy or dirty. NEVER USE EMERY CLOTH TO CLEAN CONTACT POINTS. Contact surfaces, after considerable use, may not appear bright and smooth, but this is not necessarily an indication that they are not functioning satisfactorily. OXIDIZED CONTACT POINTS - May be caused by high resistance or loose connections in the condenser circuit, oil or foreign mate rials on the contact surfaces, or most com monly, high voltages. Checkfor these conditions where burned contacts are experienced. THE CONTACT POINT OPENING - Must be set to specification. Points set too closely may tend to burn and pit rapidly. Points with excessive separation tend to cause a weak spark at high speed. The point opening of new points may be checked with a feeler gauge. Use of a feeler gauge on used points is not recommended, since the roughness of used points make it im possible to set the point opening accurately by this method. A dial indicator or a contact angle

the condenser lead or to defective connections. This will cause burned points and ignition failure upon initial start and at high speeds. CAPACITY is built into the condenser and is determined by the area of the metallic elements and the insulating and impregnating materials. For a complete check of the condense r, it is desirable to use a tester which will check for the above four conditions.
ELECTRICAL SYSTEM Section D Page 3
The use of the vacuum unit is accomplished by mounting it to the distributor clamp arm assembly, The diaphragm in the unit is linked to the distributor so that advance and retard is obtained by moving the distributor in its mounting. The movement of the diaphragm is actuated by vacuum from 'the engine manifold and a calibrated return spring. When the engine is idling the vacuum unit has no action on the distributor. When the throttle is opened slowly the vacuum is high and spark will be given additional advance to that of the centrifugal advance. On full load wide open throttle when the vacuum is low or at high speed, the vacuum unit will not advance the spark. Under these low vacuum conditions spark advance depends upon the centrifugal mechanism in the distributor.
Vacuum Automatic
Vacuum controlled spark is combined with centrifugal-automatic type distributors to ob tain greater economy and improved engine performance. The centrifugal-automatic spark mechanism is calibrated to give proper spark advance for the full load, wide-open throttle requirements of the particular engine.
Full Automatic
There is no manually operated spark ad vance with this type of spark control, thus making the variation of the spark dependent entirely upon the centrifugal automatic mecha nism.
Clamp arm Indicator Vacuum unit support
A22617
Fig. ism.
- Details of the vacuum advance mechan
PRtNTED IN UNITED STATES OF AMERICA
a
~
~
~
~
E~
BRUSH BRUSH BRUSH SPRING RMATURE TERMINAL FIELD TERMINAL IVE END "FRAME
en
1!.
..
'g
~
~ [
q !
r'
::0
z tTl
;s::
d ::0
()
en
R
BAND
tTl
EALED BALL BEARING

A-30519
Fig. 1 - Sectional View of Generator (Delco-Remy Model 1100019 and Model 1102785)
'"On",,':l::I
ooOOn ~ ......
t"' t'1
to1
.,
~gt'1~
1Il~~H
..... t'1!$:t"'

1)J(\l1o{t'" OQ ~ CIl t<l (\l .... ..., C1
'tICIlCllt<l
Ngt<l...,
t<l~~
C1
FIELD TERMINAL ARMATURE TERMINAL
GROUND SCREW... POLE SHOE SCREW
:p r
('l1
"
BUSH
3:"
~
(')
THRU BOLT
n ('l1
GROUNDED BRUSH HOLDER COMMUTATOR END FRAME DRIVE END FRAME
A-30520
Fig. 2 - Sectional View of Generator (Delco-Remy Model 1105876)
IE
II
ELECTRICAL SYSTEM Section E Page 1
GENERATORS
Worn brushes should be replaced. They can be seated with a brush seating stone. When held against the revolving commutator, the abrasive material carries under the brushes, seating them in a few seconds. Blowout abra sive particles after seating brushes. Check brush spring tension, which should be approximately 24-28 ounces.
Generator Disassembly
At regular intervals, the actual mileage or time depending on the type of operation, the generator should be disassembled for a thor ough cleaning and inspection of all parts. Never clean the armature or fields in any degreasing tank, or with grease dissolving materials, since these may damage the insulation. The bali bearing should be cleaned and repacked with a good grade of ball bearing grease. The com mutator should be trued in a lathe and the mica undercut if necessary. All wiring and connec tions should be checked. Rosin flux should be used in making all soldered connections. ACID FLUX MUST NEVER BE USED ON ELECTRI CAL CONNECTIONS.
A~22543
Fig. I - Sectional view of generator.

DELCO-REMY GENERATORS
MODELS 1102674 AND 1102714
The Delco-Remy Models 1102674 and 1102714 Generators Fig. 1 are 6 volt, 4-9/16 inch diameter frame size, ventilated, two-brush shunt units, with a ball bearing supporting the armature at the drive end and a bronze bushing in the commutator end. They are force-draft ventilated by means of a fan, mounted back of the drive pulley, which rotates with the arma ture shaft. The generator output is regulated by the correct settings of the current and voltage regulator.
Checking Inoperative Generator

Several conditions may require removal of the generator from the engine and further checking of the generator, as follows: 1. NO OUTPUT
Generator Maintenance
Generator maintenance may be divided into two sections, normal maintenance required to assure continued operation of generator, and the checking(1~(1 repair of inoperative units.
Remove cover band and check for sticking or worn brushes and burned commutator bars. Burned bars, with other bars fairly clean, indi cate open circuited coils. If brushes are making good contact with commutator, and commutator looks okay, use test leads and light and check as follows: a. Raise grounded brush, check with test 1?oints from ItAft terminal to frame. Light should not light. If it does, the generator is grounded; raise other brush from commutator and check field, commutator and brush holder to locate ground.
If generator is not grounded check
Normal Generator Maintenance

LUBRICATION - The two hinge cap oilers should be supplied with 10 to 20 drops of light engine oil every 1000 miles of operation. Do not evil excessively. NEVER OIL COMMUTA TOR. INSPEC TION - The cover band should be removed and the commutator and brushes in spected at regular intervals. If the commutator is dirty, it may be cleaned with #00 sandpaper. Blowout all dust after cleaning. NEVER USE EMERY CLOTH TO CLEAN COMMUTATOR. If the commutator is rough, out of round, or has high mica, it should be turned down on a lathe and the mica undercut.
PRIN1"O IN UNj1"e:O STATES
b. c.
field for open circuit. is not open, check for shorted field. Field draw at 6 volts should be 1.75 to 1.90 amperes. Ex cessive current draw indicates shorted field.
If trouble has not yet been located, remove armature and check on growler for short circuit.
If the field
d.
or
AMERICA
ELECTRICAL SYSTEM Section E Page Z
L-LlNE MOTOR TRUCK SERVICE MANuAL

4. NOISY GENERATOR Noisy generator may be caused by loose mounting or drive pulley, or worn, dry or dirty bearings, or improperly seated brushes. Brushes may be seated by using brush seating stone, referred to under Normal Generator Maintenance.
Z.
UNSTEADY OR LOW OUTPUT Check as follows: a. Check drive belt tension. b. Check brush spring brushes for sticking. tension and
c. Inspect commutator for roughness, grease and dirt, dirt in slots, high mica, out of round, burned bars. With any of these conditions, the commuta tor must be turned down in a lathe and the mica undercut. In addition, with burned bars which indicate open circuit, the open circuit condition must be eliminated or the armature replaced. 3. EXCESSIVE OUTPUT Excessive output usually results from a grounded generator field - grounded either in ternally, or in the regulator Opening the field circuit (disconnecting lead from !lF!I terminal of regulator or generator) with the generator operating at a medium speed will determine which unit is at fault. If the output drops off, the regulator is causing the condition. If the output remains high, the field is grounded in the generator, either at the pole shoes, leads, or at the "F" terminal.
Installation Caution
After the generator is reinstalled on the engine, or at any time after leads have been disconnected and then reconnected to the gen erator, a jumper lead should be connected MOMENT ARIL Y between the BATTERY and ARMA T URE te rminals of the regula tor, before starting engine. This allows a momentary surge of current from the battery to the gener ator which correctly polarizes the generator with respect to the battery it is to charge.
ELECTRICAL SYSTEM Section F Page 1
HEADLIGHTS
Sealed-Beam Headlights
The optical parts are so constructed that the light source, reflector, lens, and gasket are all assembled in one complete, securely sealed unit. Among the advantages of Sealed-B earn head lights are: (a) relief from glare in llTRAFFIC (LOWER) BEAM!! because of better light dis tribution; (b) maintained lighting efficiency since the optical parts of the unit are perma nently sealed against dirt, moisture. and corrosion; (c) longer-lived filaments: (d) re placement of complete optical unit in field assures original lighting efficiency, thereby avoiding poor lighting results through use of improper lens. reflectors, or bulbs. Sealed-Beam headlights provide two sepa rate and distinct beams and produce consider able more light than former-type headlights. There is a I!COUNTRY (UPPER) BEAMIf and a tfTRAFFIC (LOWER) BEAM. The "COUNTRY (UPPER) BEAM" is de signed to give even road illumination for a con siderable distance and is intended for use on the when other vehicles are not The "TRAFFIC (LOWER) BEAMfI is in tended for use in traffic. It is low enough on the left side to avoid glare in the eyes of oncom ing drivers, and at the same time the distribu tion of light on the right side will illuminate the road as far ahead as practical without causing glare on curves. Changing from "COUNTRY (UPPER) BEAM" to "TRAFFIC (LOWER) BEAM" is accomplished through use of the foot dimmer switch. CAUTION: Always use the "TRAFFIC (LOWER) BEAMII ',Vhen meeting other vehicles.
Fig. I - Removing headlight door.
Replacements (Sealed-Beam Units)

Should a filament burn out or a lens break, the entire Sealed-Beam unit must be replaced. Maximum lighting efficiency is thus assured. The added cost of the replacement unit will be balanced or offset by the longer-lived filament us ed in the cons truction of the sealed unit. Replacement of a bulb or lens is accom plished only through the of the entire unit. To do this:
Fig. 2 - Remove retainer ring screws.

2. Remove unit retaining ring by removing three screws. (See Fig. 2.) 3. Remove unit from headlight body and dis connect three-way connector at the rear. (See Fig. 3.) Reassembly is accomplished by reversing the foregoing procedure.
1. Loosen door retaining screw on headlight body. Remove door. (See Fig. 1.)
Fig. 5 - Adjusting vertical beam. Fig. 3 - Removing sealed-beam unit.
Vertical or up-and-down adjustnlent is acconlplished at screw in Fig. 5. When suitable headlight testing equipnlent is not available, the following chart will be helpful.
Center of truck
Left light
Right light
Head light
___
~en~,~eig~,{//ti@;~A.w/~lWh$S%W;t,?'~
Projected ..,C...l l l - - / pattern, upper beam
Fig.
- Adjusting laterial or side beam.
Fig. 6
Adjustment
Headlight adjustnlent should always be effected on a level floor, otherwise ainling of projected beanls will be inaccurate. Truck should be enlpty. Laterial or side adjustnlent is plished at screw in Fig. 4. aCCOnl
Ainling of headlights of Sealed-Beanl type is effected by projecting the "COUNTRY (UPPER) BEAM" of each individual headlight upon a screen or chart at a distance of twenty five feet fronl the headlight. The truck should be squarely lined up with the screen. Vertical lines on the chart nlark the distance between the center lines of the headlights and are equal ly spaced fronl the center line of the chart.

A horizontal line On the chart shall be placed at a level 3 inches below the height of the head light centers above the floor. Each headlight must be adjusted so that the hot spot of the beam will be centered over the point of inter section of the vertical and horizontal lines. (In some states this aiming conflicts with ex isting laws and regulations; wherever such is the case the legal requirements control and these instructions should be modified accord ingly.) Fig. 6 illustrates the beam pattern to be attained.
. . .;:q;;;;:f
Independent circuit breakers (black body"'''''''''''''''' insulating material)
Cut insulator to remove one or more circuit breakers
PARKING LIGHTS
Independent terminal blocks

(green body
insulating material)
Body insulating
material
Circuit breaker and terminal block assembly
A-22719
Fig. 8 - Circuit breakers.

breakers can be identified by their "green" color body insulating material, whereas ter minal blocks have "black" color body insulating material. The headlight upper beam circuit and lower beam circuit have independent circuit breakers to eliminate failure of both circuits at the same time should a short occur. For example: Should a short occur in the headlight upper beam cir cuit, the lower beam circuit would not be af fected and could be utilized immediately by de pressing the dimmer switch. Individual replacement of a circuit breaker can be accomplished by disconnecting cables and cutting the insulator between the circuit breakers as shown in Fig. 8. Remove circuit breaker from frame by pulling on terminal screws with pliers. To install, press circuit breaker into frame by hand. A dead short in a circuit will cause the circuit breaker bi-metal plate to heat suffi ciently and pull away from its contact points immediately cutting off the flow of current. A partial short will cause intermittent current flow causing the lights to dim and flicker, this should be taken as a warning and the vehicle brought to a safe stop as soon as possible. In other units in addition to headlights, a dead short can be detected by the ammeter indi cating a heavy discharge momentarily until such time as the circuit breaker opens and the cir cuit is broken. A partial short can be detected by abnormal fluctuation of the ammeter. The two (2) terminal blocks in the assembly are used to connect circuits for fuel guage units, dimmer switch feed cable, side mounted fuel tanks, fog lights, directional signals, etc.
Fig. 7
The parking lights. located just below the headlights, are equipped with ordinary filament bulbs. Should it become necessary to replace either a parking light lens or bulb, remove the rim retaining screws, as shown, replace the necessary parts and reassemble.
CIRCUIT BREAKERS
Independent current circuit breakers are used to protect theheadlighthigh-and-Iowbeam circuits, parking lights, tail lights, stop lights, and horn circuits from possible damage should a short circuit occur. Each circuit breaker is a sealed non-ad justable unit and consists of a bi-metal plate, contact points, and is connected in series with its respective circuit. Six (6) circuit breakers and two (2) ter minal blocks are included in the assembly as illustrated in Fig. 8, and are located on the ve hicle at the engine side of the cab dash paneL The circuit breakers and terminal blocks are similar in outward appearance but different in inward construction and function. Circuit
PRINTED IN UNITED 51',&.T6 OF ,&.",,RiC,t.
Testing The Circuit Breaker

Should current-flow in one of the circuits eITlploying a circuit breaker be interrupted, it is possible that there is a short in the circuit or that the circuit breaker is defective and is holding open. To check for current-flow through the circuit breaker reITlove the cables froITl both circuit breaker terITlinals and connect a hotlead cable to the circuit breaker terITllnal ITlarked "BATt! and atest light to the reITlainingterITlinal ITlarked t!AUXt!. If test light fails to light, the circuit breaker is defective and should be re placed.
Circuit breaker
Rheostat Light switch Fig. 9

A-22502
LIGHT SWITCH REMOVAL (DELCO-REMY)

1. Pull light switch knob outward to head light bright position.
the knob retainer with the retaining easily pushed into contacting the end ther ITloveITlent). spring. (Upon engageITlent spring, the knob cannot be position since the spring. of the shaft, prevents fur
2. Depress shaft release button (Fig. 9)

on switch body and pull switch knob and shaft out of switch body.
3. ReITlove ferrule nut by positioning a

punch in one of the" indentations in nut face, and tap punch lightly turning nut in a counter-clockwise direction.
With the knob inposition as shown (Fig. 10) and with the end of the thuITlb at the top edge of the knob face, press the knob with a cOITlbination lifting and pushing ITlotion, perforITled siITlul taneously, into position on the shaft. The lifting ITlotion serves to def~ect the knob retainer spring tab, and the pushmg ITlO tion forces the knob into position. Installation of the control button on the windshield wiper switch requires that the above instruction be carried out in detail, since un reasonable pressure against the shaft of the windshield wiper switch is apt to daITlage the switchITlechanisITl. When the control knobs are installed as instructed, no difficulty should be experienced and the operation can be perforITled with ease, NOTE: The carburetor hand throttle con trol knob, the windshield wiper control knob, and the choke wire control knob are reITloved in the saITle ITlanner as prescribed for the light switch control knob.
4. Unscrew
switch retainer nut shaft bushing) out of switch.
(also
5. ReITl,ove various electrical cables froITl

switch.
6. The light switch pull knob can be re

ITloved by inserting a thin tool in the sITlall hole in the knob, and pushing the spring lock inside the knob forward (toward knob end of switch). Hold spring lock in forward position and pull knob off of shaft.
7. Installation of the light switch follows:
8. Install electrical cables.
9. Align flat on switch shaft with flat in

rheostat asseITlbly in switch (see Fig. 9) and push light switch shaft into its bore in switch body. Install switch re tainer nut and ferrule nut. Use saITle ITlethod for installing ferrule nut as prescribed for reITloval except turn nut clockwise. 10. Align flat on fight switch knob with flat on shaft and push knob on shaft by fol lowing detailed instructions outlined below:
.....
Flat on shaft
..$.
/') ~
It,I
- , Knob stops here when fully installed
Instructions for Installing Control Knobs.

Place the control knob in position on the shaft until the end of the shaft just begins to engage the locking hole in the tab portion of
A-23441
Fig. 10
ELECTRICAL SYSTEM Section G Page 1
HORN
Contact point 'adjusting nut
and screw
Low Horn Voltage

"'-.01U.4.. 1
point air gap
Armature
Contact
If the horn produces a weak signal, the voltage at the horn should be checked. Connect a voltmeter from the horn terminal to ground when checking horns having one terminal. Con nect the voltmeter across the horn terminals when checking horns having two terminals. The voltage readings should not be less than 5.25 volts (six-volt system) or 11 volts (twelve-volt system). A lower reading would indicate either a low battery or a high resistance in the horn circuit.
Low Battery
Check the battery with a voltmeter or hy drometer for condition of charge. If low, the battery should be recharged.
Auto-Lite Horn No. HW4007

A22744
Loose or Corroded Connections in Horn

Circuit
Clean and tighten connections wherever necessary. Check for defective wiring by con necting separate test leads from the horn to the battery. A loose connection or poor contact at the horn push-button switch may cause the horn to operate intermittently. Shunt around the horn button to determine whether there is poor contact at the push-button switch.
Fig, I
Electrically Operated Horn

The electrically operated horns are vibrat ing type units that operate on a magnetic prin ciple to produce the warning signal. Current from the battery flows through the windings within the horn power plant when the circuit is completed at the horn push-button switch. The magnetic attraction of the armature toward the pole causes a tension and slight movement of the diaphragm. This movement opens the con tact points in series with the horn windings, breaking the circuit. When the current is in terrupted, the armature returns to its original position, relieving the tension of the diaphragm. The slight return movement of the armature and diaphragm allows the contact points to close, completing the circuit. This cycle is repeated a great many times per second, resulting in a rapid vibration of the diaphragm. Each horn is designed to operate at a predetermined number of cycles per second to produce its character istic warning signal. The pitch of the horns de pends upon the number of vibrations per second, the high note horns having the greater fre quency.
Loose or Damaged Parts

Horns usually have a rasping sound when vital parts are loose or broken. A loose dome may affect the tone. Tighten all mounting nuts and replace all damaged parts.
Adjustment (For Auto-Lite Horn No. HW-4007)

1. Remove the horn dome. To remove, pry under the edge of the dome with a sc rew driver at a point approximately opposite the terminal. On horns using a gasket under the dome, place the screwdriver between the dome bead and the projecto r and loosen with a twist of the screwdriver. 2. It is important that the horn circuitbreaker contact points be kept clean. Rub briskly with crocus cloth, then c lean with linen tape and carbon tetrachloride. Remove all residue by drawing a piece of clean tape between the contacts. 3. Tighten all flange bolts.
Conditions Affecting Horn Performance

The following conditions affect the per formance of the horns and should be checked before attempting to make any adjustments to the instruments:
PJ'tlN1'ED IN UNITED STATES OF AMERICA
4. Tighten the two screws holding the circuit breaker, with a socket wrench. Be sure contacts are aligned and that the circuit
ELECTRICAL SYSTEM Section G Page 2

Horn Relay Checks and Adjustments
Three checks and adjustments are required on the horn relay: air gap. point opening and closing voltage. The air gap and contact point opening checks and adjustments should be made with the battery disconnected.
breaker spring does not rub against the armature bolt.
5. Check the resistance of the resistor which is connected across the contact points. Its resistance should be 2.5 to 2.8 ohms and is measured by placing a card between the contacts and measuring across the resistor terminals.
Air Gap
The air gap should not normally require adjustment unless the relay has been misad justed. Check the air gap with the points barely touching and adjust if necessary by bending the lower point support.
6. Check the armature air gap on all sides.

Adjust to .0495 11 by loosening the lock nut and turning the armature. Tighten the lock nut, then recheck the gap making sure the gauge is a snug fit on all sides. NOTE: Sometimes the armature spring' plate sticks to the armature and prevents it from turning. To loosen, tap the arma ture spring plate lightly with a screwdriv er.
.7.
Contact Point Opening

Check the contact point opening and adjust by bending the upper armature stop.
Connect for tuning test with the ammeter in series with the horn terminal and a 6 volt battery and the horn frame grounded to the other battery terminal. Connect the voltmeter from the horn terminal to a clean spot on the horn frame. Adjust the amper age draw for each horn to 15 amperes at 6.2 volt.s by loosening the lock nut on the circuit breaker contact and turning the ad justing sc rew. Retighten the lock nut.
Closing Voltage
To check the relay closing voltage, connect a variable resistance of 10 ohms in series with the relay 1'E1f terminal and connect a voltmeter between the ns" and the ''Elf terminals as shown in Fig. 2. With the horn button closed. slowly decrease the amount of resistance in order to check the relay closing voltage. Adjust the closing voltage by bending the armature spring post. Bending down to increase the spring ten sion increases the closing voltage while bend ing up decreases the closing voltage. NOTE: Late type horn relay terminals do not carry any markings. but relationship of the terminals is as shown in Fig. 2.
Horn Relay
The horn relay is connected into the horn and battery circuit so as to make a more direct connection between the battery and horns, elim inating the horn button wiring from the horn circuit proper so that higher voltage becomes available at the horns and better horn perform ance is obtained. The horn relay consists of a winding assembled on a core above which an armature is placed. The armature has a point positioned above a stationary point.
Horn Relay Operation

When the horn button is depressed, the circuit from the battery is completed through the horn relay winding; this causes a magnetic field which pulls the relay armature down so that the circuit between the battery and horns is completed. The horns function and will con tinue to function as long as the horn button re mains in the closed position.
Variable resistance To battery
Voltmeter
A.22B77
Fig. 2
L~LlNE
ELECTRICAL SYSTEM Section H Page 1
REGULATORS
Three-Unit Regulator
The Delco Remy three-unit regulator is designed for use with shunt-type generators with externally grounded field circuits. The regulator contains a cutout relay, a voltage regulator, and a current regulator (Fig. L) The relay core and windings are assem bled into a frame. A flat steel armature is attached to the frame by a flexible hinge so that it is centered just above the end of the core. The armature has one or two contact points which are located just above a similar number of stationary contact points. When the generator is not operating the armature con tact points are held away from the stationary points by the tension of a flat spring riveted on the side of the armature.
Voltage regulator
CUTOUT RELAY ACTION--When the generator voltage builds up to a value great enough to charge the battery, the magnetism induced in the relay windings is sufficient to overcome the armature spring tension and pull the armature toward the core so that the contact points close. This completes the circuit be tween the generator and battery. The current which flows from the generator to the battery passes through the series winding in the proper direction to add to the magnetism holding the armature down and the contact points closed.
Fig. I - Three-unit regulator. Cover removed to show the Cut-out relay, Current regulator and Voltage regulator.
Cutout Relay
The cutout relay has two windings assem bled on one core, a series winding of a few turns of heavy wire and a shunt winding of many turns of fine wire. The shunt winding is shunted across the generator so that generator voltage is impressed upon it at all times. The series winding is connected in series with the charging circuit so that generator output passes through it (Fig. 2.)
Battery
When the generator slows down or stops, current begins to flow from the battery to the generator. This reverses the direction that the current flows through the series winding, thus causing a reversal of the series winding magnetic field. The magnetic field of the shunt winding does not reverse. Therefore. instead of helping each other, the two windings now magnetically oppose so that the resultant mag netic field become s insufficient to hold the armature down. The flat spring pulls the arm ature away from the core so that the points separate; this opens the circuit between the generator and battery.
~t.
Ammeter
Bat. Gen.
"'22740
Fig. 2-Wiring circuit of three-unit regulator.

PRINTED IN UNtTEO STATES OF AMEFUCA
VOLTAGE REGULATOR ACTION--When the generator voltage reaches the value for which the voltage regulator is adjusted, the magnetic field produced by the two windings (shunt and series) overcomes the armature spring tension and pulls the armature down so that the contact points separate. This inserts resistance into the generator field circuit so that the generator field current and voltage are reduced. Reduction of the generator voltage re duces the magnetic field of the regulator shunt winding. Also, opening the regulator points opens the regulator series winding circuit so that its magnetic field collapses completely. The consequence is that the magnetic field is reduced sufficiently to allow the spiral spring to pull the armature away from the core so that the contact points again close. This directly

Temperature Compensation
Voltage regulators are co:mpensated for te:mperature by :means of a bi-:metal ther:mo static hinge on the ar:mature. This causes the regulator to regulate for a higher voltage when cold which partly co:mpensates for the fact that a higher voltage is required to charge a cold battery. :Nlany current regulators also have a bi-:metal ther:mostatic hinge on the ar:mature. This per:mits a so:mewhat higher generator out put is cold but causes the output to drop off as te:mperature increases.
grounds the generator field circuit so that gen erator voltage and output increase. The above cycle of action again takes place and the cycle continues at a rate of ISOto 250ti:mes a second, regulating the voltage to a constant value. By thus :maintaining a constant voltage the gener ator supplies varying a:mounts of current to :meet the varying states of battery charge and electrical load. CURRENT REGULATOR ACTION--When the load de:mands are heavy, as for exa:mple, when electrical devices are turned on and the battery is in a discharged condition, the voltage :may not increase to a value sufficient to cause the voltage regulator to operate. Consequently, generator output will continue to increase until the generator reaches rated :maxi:mu:m. This is the current value for which the current regu lator is set. Therefore, when the generator reaches rated output, this output flowing through the cur rent regulator winding, create s sufficient :magnetis:m to pull the current regulator ar:ma ture down and open the contact points. With the points open, resistance is inserted into the generator field circuit so that the generator output is reduced. As soon as the generator output starts to fall off, the :magnetic field of the current regu lator winding is reduced, the spiral spring tension pulls the ar:mature up, the contact points close and directly connect the generator field to ground. Output increases and the above cycle is repeated. The cycle continues to take place while the current regulator is in opera tion 150 to 250 ti:mes a second, preventing the generator fro:m exceeding its rated :maxi:murn. When the electrical load is reduced (elec trical devices turned off or battery co:mes up to charge), then the voltage increases to that the voltage regulator begins to operate and tapers the generator output down. This pre vents the current regulator fro:m operating. Either the voltage regulator or the current regulator operates at anyone ti:me - the two do not ope rate at the sa:me ti:me.
Regulator Polarity
So:me regulators are designed for use with negative grounded batteries while other regu lators are designed for use with positive grounded batteries. Using the wrong polarity regulator on an installation will cause the regu lator contact points to pit baaly and give very short life. As a safeguard against installation of the wrong polarity regulator, all 1118300 type regulators have the :model nu:mber and the polarity clearly sta:mped on the end of the regu lator base.
REGULATOR MAINTENANCE General Instructions

1. Mechanical checks and adjust:ments (air gaps, point opening) :must be :made wit,h battery disconnected and regulator prefer ably off the vehicle. CAUTION: The cutout relay contact points :must never be closed by hand with the battery connected to the regulator. This would cause a high current to flow through tte units which would seriously da:mage the:m. 2. Electrical checks and adjust:ments :may be :made either on or off the vehicle. The regulator :must always be operated with the type generator for which it is designed. 3. The regulator :must be :mounted in the operating position when electrical settings are checked and adjusted and it :must be at operating te:mperature.
Resistances
The current and voltage regulator circuits use a co:m:mon resistor (Fig. 2) which is in serted in the field circuit when either the cur rent or voltage regulator operates. A second resistor (Fig. 2) is connected between the regu lator field ter:minal and the cutout relay fra:me, which places it in parallel with the generator field coils. The sudden reduction in field cur rentoccuring wheneither the current orvoltage regulator contact points open, is acco:mpanied by a surge of induced voltage in the field coils as the strength of the :magnetic field changes. These surges are partially dissipated by the two resistors, thus preventing excessive arcing at the contact points.
4. After any tests or adjust:ments the genera tor on the vehicle :must be repolarized after leads are connected but before the is started, as follows:
Repolarizing Generator
After reconnecting leads, :mo:mentarily connect a ju:mper lead between the "GENI! and "BAT" ter:minals of the regulator. This allows a :mo:mentary surge of current to flow through

the generator which correctly polarizes it. CAUTION! Failure to do this may result in severe damage to the equipment since reversed polarity causes vibration, arcing and burning of the relay contact points.
ELECTRICAL SYSTEM Section H . Page 3
with the generator opelfating at medium speed. If the output remains high, the generator field is grounded either in the generator or in the wiring harness. If the output drops off the regulator is at. fault and it should be checked for a high voltage setting or grounds.
QUICK CHECKS OF GENERATOR AND REGULATOR

In analyzing complaints of generator-regu lator operation, any of several basic conditions may be found.
+
Discharged
High charging rate
Fully charged
Low
charging rate
Normal
..
~
A22715
3. DISCHARGED BATTERY AND HIGH CHARGING RATE--This is normalgener ator-regulator action. RegUlator settings may be checked as outlined in the following section
1. FULLY CHARGED BATTERY AND LOW CHARGING RATE--This indicates normal generator-regulator operation. Regulator settings may be checked as outlined on following pages.
+~=
Discharged Low or no charging rate
~
Unde~ch~rging
(?
A226M
4. DISCHARGED BATTERY AND LOW OR NO CHARGING RATE-
Fully charged
High
charging rate
This condition could be due to: (a) Loose connections, frayed or damaged wires.
2. FULLY CHARGED BATTERY AND A HIGH CHARGING RATE--This indicates that the voltage regulator is not reducing the generator output as it should. A high charging rate to a fully charged battery will damage the battery and the accom panying high voltage is very injurious to all electrical units. This operating condition may result from: (a) Improper voltage regulator setting. (b) Defective voltage regulator unit. (c) Grounded generator field circuit (in either generator, regulator or wiring). (d) Poor ground connection at regulator. (e) High temperature which reduces the resistance of the battery to charge so that it will accept a high charging rate even thouth the voltage regulator setting is normal.
If the trouble is not due to high tempera ture, determine the cause of trouble by discon necting the lead from the regulator "Ffl terminal
PitlNTEO IN UNIl'D STArES 0'- AMERICA.
(b) Defective battery. (c) High circuit resistance. (d) Low regulator setting. (e) Oxidized regulator contact points. (f) Defects within the generator.
If the condition is not caused by loose con nections, frayed or damaged wires, proceed as follows to locate cause of trouble.
To determine whether the generator or regulator is at fault, momentarily ground the 11Ft! terminal of the regulator and inc rease gen erator speed. If the output does not increase, the generator is probably at fault. If the gener ator output increases, the trouble is due to: (a) A low voltage (or current) regulator setting. (b) Oxidized regulator contact points which insert excessive resistance into the generator field circuit so that out put remains low.

THREE-UNIT REGULATOR CHECKS AND
ADJUSTMENTS
(c) Generator field circuit open within the regulator at the connections or in the regulator winding. 5. BURNED RESISTANCES, WINDINGS OR CONTACTS--These result from open cir cuit operation, open resistance units, or high resistance in the charging circuit. Where burned resistances, windings or contacts are found, always check car wiring before installing a new regulator. Otherwise, the new regulator may also fail in the same way. 6. BURNED RELAY CONTACT POINTS- This may be due to reversed generator polarity. Generator polarity must be cor rected as explained on page 2 after any checks of the regulator or generator, or after disconnecting and reconnecting leads.
Cutout Relay
The cutout relay require s three checks and adjustments: air gap, point opening and closing voltage. The air gap and point opening adjustments must be made with the battery disconnected.
Cleaning Contact Points

The contact points of a regulator will not operate indefinitely without some attention. It has been found that a great majority of all reg ulator trouble can be eliminated by a simple cleaning of the contact points, plus some pos sible readjustment. The flat points should be cleaned with a spoon or riffler file. On nega tive grounded regulators which have the flat contact point on the regulator armatures, loosen the contact bracket mounting screws so that bracket can be tilted to one side (Fig. 3), On positive grounded regulators, the flat point is in the upper contact bracket so the bracket must be removed for cleaning the points. A flat file cannot be used successfully to clean the flat contact points since it will not touch the center of the flat point where point wear is most apt to occur. NEVER USE EMERY CLOTH OR SANDPAPER TO CLEAN THE CONTACT POINTS.
Fig. q - Air gap check and adjustment. Battery must be disconnected when this check is made.
AIR GAP--Place fingers on armature directly above core and move armature down until points just close and then measure air gap between armature and center of core (Fig. 4). On multiple contact point relays, make sure that all points close simultaneously. If they do not, bend sprin'g finger so they do. To adjust air gap, loosen two screws at the back of relay and raise or lower the armature as required. Tighten screws after adjustment.
Spoon or riffler file
POINT OPENING--Check point opening and adjust by bending the upper armature stop (Fig. 5), CLOSING VOLTAGE--To check the closing voltage of the cutout relay, connect the regulator to the proper generator and battery, connect a voltmeter between the regulator lIGEN" terminal and regulator base, and connect an ammeter into the charging circuit at the regulator "BAT" terminal as shown. in Fig. 6. Slowly increase the generator speed and note relay closing voltage. Decrease generator speed and make sure that cutout relay contact points open. Adjust closing voltage by turning adjusting
To dean contact points loosen upper contact

bracket mounting screws
A-22532
Fig. 3 - Use spoon or riffler file to clean flat contact points in regulator.

screw (Fig. 7). Turn screw clockwise to in crease spring tension and closing voltage, and turn screw counterclockwise to decrease clos ing voltage.
AIR GAP--To check air gap, push arma ture down until the contact points are just touching and then measure air gap (Fig. 13), Adjust by loosening the contact mounting screws and raising or lowering the contact bracket as required. Be sure the points are lined up, and tighten screws after adjustment.
Adjusting screw-
turn to adjust closing voltage
Fig. 7-Adjusting cutout relay closing voltage. Fig. 5 - Cut-out relay point opening check and adjustment. Battery must be disconnected when this check is made.
Connect to ground
Contact screws-
loosen to set air gap
A-22535
Fig. 8 - Voltage regulator air gap check.

VOLTAGE SETTING--There are two ways to check the voltage setting--the fixed resist ance method and the variable resistance method (Figs. 9 and 10). FIXED RESISTANCE METHOD-- With the fixed resistance method, a fixed resistance is substituted for the external charging circuit by disconnecting the battery lead at the regulator and connecting the resistance between the regu lator "BAT" terminal and ground. A test volt meter is connected in parallel with the fixed resistance as shown in Fig. 9. The resistance must be3/4 ohm* for 6 volt units, 1-112 ohms* for 12 volt units, 7 ohms for 24 volt units, and must be capable of carrying 10 amperes with out any change of resistance with temperature changes. ... - See note on following page.
Ammeter
Voltmeter
Generator
A-22619
Fig. 6 - Connections to be made when checking relay closing voltage and reverse current to open relay points.
Voltage Regulator
Two checks and adjustments are required on the voltage regulator, air gap and voltage setting.
PRINTED iN UNITED STATES OF AMERICA
Regulator
@
\3-4 ohm-6 volt Fixed resistance 11-2 ohm-12 volt 17 ohm-24 volt
Connect to
ground
Voltmeter
Generator
A-22714
Fig. 9 - Fixed resistance and voltmeter connec tions to check voltage regulator setting by fixed resistance method. Connections are simi I ar for both two-un it and three un i t regu Iators.
Variable resistance Ammeter
Voltmeter
Generator
A-22620
Fig. 10 - Voltmeter ammeter and variable resis tance connections for checking voltage regulator setting by the variable resistance method.
*NOTE: With all 6 volt regulators having current ratings less than 15 amperes, it is necessary to use a 1-1/2 ohm fixed resistance to avoid interference from the current regula tor. With all 12 volt regulators having current ratings less than 15 amperes, a 2-1/4 ohm fixed resistance (314 ohm and 1-112 ohm re sistors in series} must be used for the same reason.
With generator operating 25 per cent above rated output speed and with regulator at oper ating temperature, note voltage setting, Cover must be in place.
Fig. I I - Adjusting voltage regulator setting.

To adjust voltage setting, turn adjusting screw (Fig. 11), Turn screw clockwise to in crease voltage setting and counterclockwise to decrease voltage setting.
If the unit is badly out of adjustInent. refer to section headed REGULA TOR SPRING RE PLACEMENT.
CAUTION: If adjusting screw is turned down (clockwise} beyond normal adjustment range, spring support may fail to return when pressure is relieved. In such case, turn screw counterclockwise until sufficient clearance de velops between screw head and spring support, then bend spring support upward carefully with small pliers until contact is made with screw head. Final setting of the unit should always be approached by increasing spring tension, never by reducing it. If setting is too high, adjust unit below required value, and then raise to exact setting by increasing spring tension.
After each adjustment and before taking voltage reading, replace the regulator cover, reduce generator speed until relay points open and then bring the generator back to speed again.
VARIABLE RESISTANCE METHOD--Con nect ammeter into charging circuit at l'BATI! terminal of regulator with 114 ohIn variable resistance in series. Connect voltIneter from regulator l'BAT11 terminal to ground as shown

in Fig. 10. Increase generator speed to 25 per cent above rated output speed. If less than 8 amperes is obtained {or less than 4 amperes on low output 6 and 12 volt generators}, turn on lights to permit increased generator output. Cut in resistance until output is reduced to 8-10 amperes (4-6 amperes on 6 and 12 volt .gener ators having current ratings less than 15 am peres). Operate until reg111ator reaches oper ating temperature. Retard generator speed until relay points open, then bring generator back to speed and note voltage setting. Voltage readings must be taken with regulator at oper ating temperature and with 8-10 amperes flow ing (4-6 amperes on low output units). Cover must be in place.
Regulator
Jumper lead bridging voltage regulator contact points
NOTE: It is very important that the vari able resistance be connected at the "BAT" terminal as shown in Fig. 10 rather than at the "GEN" terminal, even though these terminals are in the same circuit. An examination of the wiring diagram, Fig. 2, will show that the regu lation begins at the point where the shunt wind ings are connected to the series circuit. Any small resistance added to the circuit between the generator and this point will simply be off set by a rise in generator voltage without affecting the output shown at the ammeter.
Ammeter
Generator
A22641
Fig. 13 - Ammeter and jumper lead connections for checking current regulator setting by the jumper lead method.
Current Regulator
Two checks and adjustments are required on the current regulator, air gap and current setting. The air gap on the current regulator is checked and adjusted in exactly the same manner as for the voltage regulator already described.
Blade of screwdriver must touch base and shield
CURRENT SETTING--To check the cur rent regulator setting, the voltage regulator must be prevented from oRe rating. Four methods of preventing voltage regulator opera tion are available. Regardless of the method used, an ammeter must be connected into the charging circuit at the regulator 'BAT" termi nal. The first method should be used for pre liminary checks whenever possible since it does not require removal of tp.e regulator cover. The four methods are as follows:
A-22536
Fig. 12 - Quick method for cutting out voltage regulator in order to check current regulator sett i ng.
Adjust regulator as previously explained. In using the variable resistance method, it is necessary to readjust the variable resistance after each voltage adjustment, and then reduce and increase generator speed before taking the voltage reading.
PRtNTED IN UNITED STATES
1. QUICK CHECK METHOD--Insert screw driver blade through oblong hole in base of regulator until contact is made with shield around resistor (Fig. 12). Be sure to keep screwdriver at right angles to base, and hold firmly in place during check so that blade touches regulator base and shield at same time. This temporarily cuts out voltage regulator unit. Turn on lights and accessories to prevent high voltage during the test.
or
AMERICA

REPAIR SECTION Regulator Spring Replacement
If it becomes necessary to replace the spiral spring on either the current or voltage regulator unit, the new spring should first be hooked on the lower spring support and then stretched up until it can be hooked at the upper end. Stretch the spring only by means of a screwdriver blade inserted between the turns (or in a similar manner) - do not pry the spring into place as this is likely to bend the spring supports. After installing a new spring, read just the unit setting as already described.
With ammeter connected as in Fig. 13 and regulator at operating temperature, operate generator at 50 per cent above rated output speed, and note current setting. If necessary to adjust, remove cover and adjust in same manner as voltage regulator unit (Fig. 11) by turning adjusting screw clockwise to increase current setting or counterclockwise to decrease setting. See CAUTION note under Voltage Setting of Voltage Regulator. If unit is badly out of adjustment readjust as explained under REGULATOR SPRING REPLACEMENT. 2. JUMPER LEAD METHOD--Remove the regulator cover and connect a jumper lead across the voltage regulator contact points (Fig. B), Turn on lights and accessories to prevent high voltage during the test. With generator operating 50 per cent above rated output speed and with regulator at operating temperature, note the current setting. 3. BATTERY DISCHARGE METHOD--Partly discharge battery by cranking the engine for 30 seconds with ignition turned off. Never use cranking motor more than 30 seconds continuously since this would overheat and damage it. Immediately after cranking, start engine, turn on lights and accessories and note current setting with engine operating 50 per cent above rated output speed. 4. LOAD METHOD--If a load approximating the current regulator setting is placed across the battery during the time that the current regulator setting is being checked, the voltage will not increase sufficiently to cause the voltage regulator to operate. This load may be provided by a carbon pile or a bank of lights.
ReplaCing Contact Support Brackets

Voltage or current regulator contact sup port brackets can be replaced by following the relationship illustrated in Fig. 19. Note par ticularly that the connector strap is insulated from the voltage regulator contact mounting screws while it is connected to the current regulator contact mounting screws. New bush ings should always be used when installing a contact support bracket since the old bushing may be distorted or damaged.
Radio By-Pass Condensers

The installation of radio by-pass con densers on the field terminal of the regulator or generator will cause the regulator contact points to burn and oxidize so that generator output will be reduced and a run-down battery will result. If a condenser is found to have been connected to either of these terminals, disconnect the condenser and clean the regulator contact points as previously explained.
Current
Fig. I~ - Relationship of insulators, connector strap, and upper contact support brackets in three-unit regulator.
ELECTRICAL SYSTEM Section I Page 1
SPARK PLUGS
The sole purpose of a spark plug is to create a spark between the electrodes to ignite the fuel in the engine. Therefore, if anything is wrong with the spark plug that will prevent its firing. all the other units in the electrical systeIn will have functioned in vain. FroIn a cold start, a spark plug Inust operate under extreInely high teInperatures in justa fewseconds, and Inust withstand repeated terrific explosion pressures. These conditions can be duplicated only in an engine. Therefore the only reliable test of a spark plug is to oper ate it in an engine under actual operating con ditions.
Removal of Spark Plugs

A. Disconnect Ignition Wires: Detach ignition wires froIn each sparkplug. Most engines carry snap-on type connectors which siInply pull ~ff. SOIne have screw-type terIninal connections in which case it is neces sary to reInove these terIninal nuts before lift ing off the ignition wires. B. Sele ct The Socket Wrench:
Fig.
Visual Inspection
A. Gaskets:
If the gaskets are not flattened (Fig. 1) or cOInpressed it is an indication that the spark plugs have not been p.roperly tightened to pre vent blow-by between the spark plug and cylin der head. This condition results in excessive burning of the electredes and overheats the in sulator tip which Inay cause preignition.
....
It is highly advisable touse the proper size deep socket type wrench to reInove the spark plug frOIn an engine. IInproper wrenches are often the cause of spark plug insulator breakage.
C. Loosen Each
Two Turns:
Using the proper size deep socket wrench (an extension shaft between wrench and handle is highly desirable). loosen each spark plug two cOInplete turns only. All spark plugs loosen in a counter-clockwise direction. D. Blow Out The Ports:
The action of lo.osening each spark plug two turns will also loosen any accuInulation of dirt which Inaybe eInbedded around the base of the spark plug. Use a blast of cOInpressed air to reInove this debris and prevent its falling into the cylinder cOInbustion chaInber when the spark plug is reInoved. E. ReInove Spark Plugs: In Inost cases it is possible to reInove each spark plug frOIn the engine byhand. Place each spark plug and its gasket in a suitable holder in the order of reInoval froIn the engine.
PRINTED iN IJNITEO STATES OF AMERICA
Fig. 2
If the gaskets are flattened or compressed to the point where they have become distorted (out of round) or torn, it is an indication that the spark plugs have been tightened to the ex tent that damage may have been inflicted on the spark plug itself (Fig. 2).
Excessive torque often causes strains on the steel shell of the spark plug which result in cracked insulators, distortion of metal shell and gap setting, as well as blow-by between the component parts of the spark plug.
A-23113
Fig.
J.j.
Fig. 3
If the gasket is properly compressed (ap proximately half of original thickness) showing a flat, clean, even surface, it is an indication that the spark plugs have beenproperlyinstaUed (Fig. 3).
Fig. 5
B. Condition of Insulator (Firing End): (1) OIL FOULING (Fig.4)isusuallyiden tified by the wet, black shiny deposit which re sults from the following engine and spark plug conditions: Worn rings and pistons.
Worn valve stems or guides.
Weak battery.
Faulty ignition wires.
Distributor trouble.
Weak coil.
Too cold a spark plug.
(2) GAS FOULING (Fig. 5) is usuallyiden tified by a black, dry fluffy deposit which results from: Excessive use of choke.
Improper adjustment of automatic
choke. Too rich an air-fuel mixture. Prolonged periods of engine idling. Too cold a spark plug.
(4) NORMAL CONDITIONS where regular or unleaded gasolines have been used, are iden tified by a rusty brown to grayish tan powdery deposit, indicating a balanced ignition and com bustion condition (Fig. 7).
Fig. 6
(3) BURNED OR OVERHEATED spark plugs (Fig. 6) are identified usually by dry, shiny, glassy deposits on the insulator, or cracks in the insulator tip itself, which result from: Too lean an air-fuel mixture.
Inefficient engine cooling.
Poorly seated valves.
Improper ignition timing.
Too hot a spark plug for the service.
Improper installation of spark plugs.
Compression leakage through spark
plug.
Fig. 8
(5) NORMAL CONDITIONS where highly leaded gasolines have been used, are identified usually by white powdery or yellowish glazed deposits (Fig. 8). Such deposits or "enc rust ments tl do not interfere with spark plug open' ation and should merely be cleaned off at regu lar service intervals.
Fig. 9
C. Conditions Of Electrodes: The extent of service and mileage to which a spark plug has been subjected is generally best indicated by the degree of wear ofthe e1ec tr odes. When the center electrode has become worn away, or the ground electrode. has become so badly eroded at the sparking area that re
Fig. 7
PRINTED IN UNITED 'TATES OF AMERICA

deposits on the insulator nose. Prolonged use of the abrasive blast will wear away the insu lator causing irreparable rlamage to the spark plug. Visual inspection will indicate when the spark plug has been properly cleaned. Loose abrasive remaining inside the firing end should be removed by the use of the "air blast" jet on the cleaner. Do not use picks, screwdrivers. etc. to remove deposits inside the firing .end of the spark plug. D. Clean Threads: Remove loose abrasive or other foreign material from the spark plug threads by means of a wire brush (a stiff tooth brush is also sat isfactory) to complete the job of cleaning. E. Dress Spark Plug Gaps: Before actually setting the gap of a cleaned spark plug it is highly desirable to pass a thin point file or nail file between the sparking areas of the center and ground electrodes. This helps to produce flat, parallel surfaces which resist growth better than sharp or uneven areas, and facilitates more accurate gap gauging. F. Reset Spark Plug Gaps: Reset all gaps by moving the ground (or side) electrode only. Do not touch the center electrode as insulator tip fracture may result. Bend the ground electrode towards the cen ter electrode. Use a good feeler gauge to measure the clearances between the electrodes. Refer to specifications for correct gap settings. A very slight drag should be felt when the feeler gauge passes between the electrodes. The spark plug is now ready for testing.
setting of the gap is either difficult or impos sible, the spark plug is not fit for further effi cient engine service even if cleaned. D. Preliminary Examination:
If the spark plug in question exhibits insu lator cracks, worn electrodes or other obviously unsatisfactory conditions, the spark plug does not warrant further attention and should be dis carded.
Cleaning And Adjusting

A. Remove Gaskets: Regardless of the condition of the old gas kets, they should be removed from the spark plug before cleaning. If new replacement gas kets are available the old ones should be dis carded. .B. Degrease {If Necessary}: Before abrasive cleaning. any spark plugs which have oily deposits on the firing end or the outside of the spark plug should be degreased by brushing with gasoline, naptha or other suit able solvent which will dry quickly by wiping with a cloth or by air blast. Failure to do this with oil fouled spark plugs will result in pack ing of the cleaner abrasive inside the firing end of the spark plug. C. Apply Abrasive Blast: Place the spark p,lug in the rubber cleaner adapter ofthe correct size. Hold the spark plug at the terminal end and while applying the abra sive blast, "wobble" the top of the spark plug in a circle. By this method the abrasive will be able to properly clean the insulator tip and the electrodes. Three seconds time should be suf ficient to clean most spark plugs. However, the extent of cleaning time should be limited to only that which is necessary to clean off the
SUITABLE SPARK PLUG CLEANING EQUIP MENT IS AVAILABLE UNDER SE-1634 AND SE-l637. BOTH ITEMS ARE ABRASIVE TYPE CLEANERS.
.,
lit
ELECTRICAL SYSTEM
Section J Page 1
OILER
SWITCH SPRING DRIVE HOUSING
BEARING """f'nUMUTATOR COMM. END FRAME

Fig. 1 Starter (Delc:o-Remy 1108009)
DRIVE PINION BRONZ BEARI

A..30521
CTS 12-MARCH 1953 (Supplemen.al page, for CTS1I),
PRINTD IN UNITED STATES OF AMERICA.
ELECTRICAL SYSTEM Sec-tion J Page I
STARTING MOTORS (CRANKING MOTORS)

Connector bousing
Drive pinion Comm. end frame

A-22749
Fig. 3 - Delco-Remy Starter 1107967.
A-22796
Fig. I - Wiring diagram of simple electric mo tor. Showing current flow. The armature wind ings and field windings are connected in series. Delco-Remy starter motors are all series-wound units.
Fig.
Cover Field
- Delco-Remy Starter 1108217.
Fig. 2 - Delco-Remy Starter
110707~.
Starting Motors or Cranking Motors

Comm. end frame The best assurance of obtaining maximum service from cranking motors with minimum trouble is to follow a regular inspection and maintenance procedure. Periodic lubrication where required, inspection of the brushes, com mutator and drive arrangement are essentials in the inspection procedure. In addition, disas sembly and thorough overhauling of the cranking motor at periodic intervals are desirable as a safeguard against road failures from accumu
PRINTED IN UNITED STATES OF' AMERICA
Armature
Drive housing
A-22660
Fig. 5 - Delco-Remy Starter II0900Q.

lations of dust and grease and from normal wear of parts _ This is particularly de sir able on com mercial vehicles where maintenance of oper ating schedules is of especial im.portance. In addition to the cranking motor itself, the exter nal circuit between the cranking m.otor and the
ELECTRICAL SYSTEM Section J Page 2

dirty or moist operating conditions, heavy vi bration, all will make it necessary that the in spection checks be made at more frequent in tervals. Generally speaking, passenger car and other standard-duty cranking motors should be inspected at approximately 5,000 mile intervals. Heavy-duty units may not require as frequent inspection. However, where special operating conditions such as outlined above exist, inspec tion atmore frequent intervals may be required.
battery must be kept in good condition since defective wiring, loose or corroded connections will prevent normal cranking action.
Lubrication
Bearings provided with hinge cap oilers should have 8 to 10 drops of light engine oil every 5,000 miles. Grease cups should be turned down one turn every 5,000 miles and refilled with medium cup grease when required. On tractor, marine, or stationary applications, lubricate every 300 hours of operation as above. Grease plugs on gear reduction cranking mo tors should be removed every six months so the grease reservoir can be repacked with me dium grade graphite grease. On some models, oil wicks are used to lubricate the center and drive end bushings. The wicks are saturated with oil before assem bly, and should be saturated again whenever the cranking motor is taken off the engine or dis . assembled. Some cranking motors are equipped with oil-less bushings. These should be supplied with a few drops of light engine oil at any time that the cranking motor is disassembled for repair or s~rvice. Avoid excessive lubrication since this might cause lubricant to be forced out onto the commutator where it would gum and cause poor commutation with a resulting decrease in crank ing motor performance.
INSPECTION PROCEDURE:
Cranking motor action is indicative, to some extent, of the cranking motor condition. Thus, a cranking motor that responds normally when the cranking motor switch is closed is usually considered to be in good condition. (Checking a cranking motor that doe s not oper ate normally is discussed in a following sec tion.) However, the inspection procedure should include more than amere check of the cranking motor operation; the following items should also be inspected. The mounting, wiring and connections should be tight and in good condi tion. The magnetic switch or solenoid (where used) should be firmly mounted and should op erate freely and without binding. Next, remove the cover band so the com mutator, brushes and internal connections can be checked. Examine the cover band for thrown solder which results if the cranking motor is subjected to excessively long cranking periods so it overheats. This overheating causes the solder at the commutator riser bars to melt and be thrown out during cranking. Bad con nections consequently develop which in turn re sult in arcing and burning of the commutator bars and ultimate ruination of the armature. If the bars are not too badly burned, the arma ture can often be saved by resoldering the con nections at the riser bars (usingrosin, not acid, flux) turning the commutator and undercutting the mica between bars. Some cranking motor armatures are of welded construction, with the armature coil leads welded, not soldered, to the commutator bars. This type of armature should not be repaired by ordinary soldering methods. NOTE: Regardless of the type of con struction, never operate the cranking motor more than 30 seconds at a time without pausing to allow the cranking motor to cool off for a~_ least two minutes. Overheating, caused by ex ~essively long cranking periods, may seriou~ damage the cranking motor. When che.cking the brushes, make sure they are not binding and that they are resting on the commutator with sufficient tension to give good, firm contact. Brush leads and screws should be tight. If the brushes are worn down to one half their original length, (compare with new brushes) they should be replaced.
Lubricating The Bendix Drive Mechanism

Bendix drives should be lubricated with a '1all amount of light engine oil whenever the cranking motor is removed from the engine for servicing. Heavy oil or grease must not be used as this may retard or prevent normal ac tion of the drive mechanism. The overrunning clutch drive is packed with lubricant during original assembly and requires no additional lubrication.
S'
Never lubricate the commutator and do not attempt to lubricate the cranking motor while it is being operated. Be sure to keep grease or oil clean. Lubricant should be kept in closed containers.
Periodic Inspection
At periodic intervals the cranking motor should be inspected to determine its condition. The frequency with which this should be done will be determined by the type and design of cranking motor as well as the type of service in which it is used. Frequent starts, as in city operation or door-to-door delivery service,ex cessively long cranking periods caused by a hard-starting engine condition, excessively

Note the condition of the commutator. If it is glazed or dirty, it can be cleaned in a few seconds by holding a strip of number 00 sand paper against it with a piece of wood while the cranking motor is operated. A brush seating stone can also be used for this purpose. Move the sandpaper or stone back and forth across the commutator while the armature is spinning. Never operate the cranking motor more than 30 seconds at a time without pausing for a few min utes to allow the cranking motor to cool. Blow out all dust after the commutator is cleaned.
If the commutator is rough, out of round, has high mica, or is extremely dirty, it will re quire turning down in a lathe and undercutting of the mica between the bars.
Low temperatures also hamper cranking motor performance since it thickens engine oil and makes the engine considerably harder to crank and start. Also, the battery is less efficient at low temperatures. In the cranking motor, a bent armature shaft, loose pole shoe screws or worn bearings, any of which may allow the ar mature to drag, will reduce cranking perfor mance and increase current draw.
Quick Checks When in Trouble

When trouble develops in the cranking mo tor system, and the cranking motor cranks the engine slowly or not at all, several preliminary checks can be made to determine whether the trouble lies in the battery, in the cranking mo tor, in the wiring circuit between them, or else where. Many conditions besides defects in the cranking motor can result in poor cranking pe r formanc e. To make a quick check of the crankingmo tor system, turn on the headlights. They should burn with normal brilliance. If they do not, the battery may be run down and it should be checked with ahydrometer. If the battery isinacharged condition so the lights burn brightly, operate the cranking motor. Anyone of three things will happen to the lights. Theywill go out, dim considerably, or stay bright without any crank ing action taking place.
If the lights go out as the cranking motor switch is closed, it indicates that there is a poor connection between the battery and the cranking motor. This poor connection will most often be found at the battery terminals, and correction is made by removing the cable clamps from the terminals, cleaning the ter minals and clamps, replacing the clamps and tightening them securely. A coating of corro sion-inhibitor maybe applied to the clamps and terminals to retard formation of corrosion. If lights dim considerably as the cranking motor switch is closed and the cranking motor operates slowly or not at all, the battery may be run down. Or, there may be some mechan ical condition in the engine or the cranking mo tor that is throwing aheavyburden on the crank ing motor. This imposes ahigh discharge rate on the battery which causes noticeable dimming of the lights. Check the battery with a hydro meter. If it is charged, the trouble probably lies in either the engine or cranking motor it self. In the engine, tight bearings or pistons, or heavy oil place an added burden on the cranking motor.
PRIN'rt"b IN UNITED STATES 0" A~ERIC'"
In addition, more serious internal damage is sometime s found. Thrown armatur e windings or commutator bars, which sometimes occur on overrunning clutch type cranking motors, are usually caused by excessive overrunning after starting. This is a result of such conditions as the driver's keeping his foot on the cranking motor switch too long after the engine has started, the driver's opening the throttle too wide in starting, or improper throttle cracker adjustment. Any of these subject the overrun ning clutch to extra strain so it tends to seize, spinning the armature at high speed with re sulting armature damage.
On Bendix drive cranking motors, broken Bendix housings and wrapped-up Bendix springs may result if the driver closes the cranking motor switch during engine rockback after the engine starts and then stops again. Another cause may be engine backfire during cranking which may result, among other things, from ig nition timing being too far advanced. To avoid such failures, the driver should pause a few seconds after a false start to make sure the engine has come completely to rest before an other start is attempted. In addition, the igni tion timing should be reset if engine backfiring has caused the trouble.
The third condition which may be encount ered when the cranking motor switch is closed with the lights turned on is that the lights stay bright, but no cranking action takes place. This indicates an open circuit at some'point, either in the crankingmotor, or in the cranking motor switch or control circuit. Where the application is solenoid-operated, the solenoid control cir cuit can be eliminated momentarily by placing a heavy jumper lead across the solenoid main terminals to see if the cranking motor will op erate. This connects the cranking motor dir ectly to the battery and, if it operates, it indi cates that the control circuit is not functioning normally. The wiring and control units must be checked to locate the trouble. If the crank ing motor does not operate, it will probably have to be removed from the engine so it can be analyzed in detail.
Fig. 6 Schematic wiring diagram of two-pole, four-brush, series-wound cranking motor.
Fig. 8 Schematic wiring diagram of six-pole, six-brush, series-wound .cranking motor.
Field coil
A22730
Fig. 7 Schematic wiring diagram of four-pole, fourbrush, series-wound cranking motor.
ENGINES Index Page 1
ENGINE GROUP
SPECIFICATIONS
ENGINE SPECIFICATIONS . . . . . . . . . . WRENCH TORQUE LOAD CHART (Recommended). Page
1-7
8-10
SECTION "A"-SILVER DIAMOND ENGINE

MODELS{L-110, L-1Z0, LM-120, L-130, L-1S0, L-lS3, LM-lSO (SD-.220 Engine) LB-140, L-l60, L-l&3, L-l64, L-16S, LC-160 (SD-240 Engme)
DESCRIPTION . . . . . ENGINE REMOVAL . . . ENGINE DISASSEMBLY

Connec ting rods and piS tons. . ......... , ........... Cylinder head and valves . . . . . . . . . . . . . , . . . . . . . . . . . Flywheel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Main bearings . . . . . . . . .. . . . , . . . . . . . . . , . . . Manifold. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Oil pump overhaul . . , . . . . . . . . . . . . . . . . . . . . . . . ...... R ocker arms. . . . . . . . , . . . . . . . . . . . . . . Timing gears and camshaft . . , . . . . . . . . . . .... Water pump overhaul . . . . . . . . , . . . . . . . . . . . . . . . ... REPAIR OF SUB-ASSEMBLIES AND ASSEMBLING
Camshaft bushings . . . . . . . . . . . . . . . . Connecting rods and pis tons . . . . . . . . . . Crankshaft, flywheel and camshaft inspection Cylinder block inspection. . . . . . . . . Miscellaneous parts inspection . . . . . . ASSEMBLY OF ENGINE Accessories . . . . . . . Camshaft and gear .. , Clutch . . . . . . . . . . . . . . . Connecting rods and pistons. Crankshaft . . . . . . . . Cylinder head . . . . Flywheel and housing . . . . Manifold . . . . . . . . . Oil pump. . . , . . . . . . Rocker arm ass embly . Tappets . . . . . Valve adjusting . . . . .
3, 4
11
6-9
11
11
14, IS
IS, 16
4, S, 6
10
12-14
17
17-19
19, 20
17
20
26
24
24
21-24
21-23
2S 24
25
24
25
25
25
PR1NTED IN Ut-!ITEO StAtES OF'" AMERICA
ENGINE GROUP-Continued
SECTION "Bit-SUPER BLUE DIAMOND ENGINE

MODELS L-170, L-l73, L-174, L-175, LF-170, L-180, L-183, L-184, LC-180 (BD-269 Engine)
DESCRIPTION . . . ENGINE REMOVAL . . ENGINE DISASSEMBLY C onnec ting rods and pis tons. Cylinder head and valves. . Flywheel. . . . . . . . . . . Main bearings and crankshaft. Manifold. . . . . . . . . . . . . Oil pump overhaul . . . . Rocker aJ,"ms . . . . . . Timing gears and camshaft Water pump overhaul . . . . . . . . . . . . . . . . . . . . . . . . ..... . . . . . . . . . . . . .. . . . . . . .... . . . . . . . ......... . .... . ..................... . . . . .. . . . . . . . . . .
Page
2
2, 3
9
5, 6, 7
9
9
10, 11 11, 12 3-5 7-8 9, 10

REPAIR OF SUB-ASSEMBLIES AND ASSEMBLING Camshaft bushings . . . . . . . . . Connecting rods and pistons . . . . . . . . . Crankshaft, flywheel and camshaft inspec lion . Cylinder block inspection. . . . .. Cylinder sleeve fits . . . . . . Miscellaneous parts inspection. ASSEMBL Y OF ENGINE Accessories . . . . . Camshaft and Gear . . Clutch . . . . . . . . . .
Connecting rods and pistons. Crankshaft . . . . . . Cylinder head . . . . . Engine mounting . . . . Flywheel al)d housing . Manifold . . . . . . . . . Rocker arm assembly. Tappets . . . . Valve adjus ting . . . . .
13
13-15
15
12
13
16
21, 22
20
20
16-20
16-19
20
21
19-20
21
21
20
21
ENGINE GROUP-Continued
SECTION "C"-SUPER RED DIAMOND ENGINE

L-l85, L-190, L-l93, L-l94, LC-l90 (RD-372 Engine)
MODELS L-l90, L-194, L-l95, LC-190, LF-190, L-200, L-204 (RD-406 Engine)
{L-200, L-204, L-205, LC-200, L-21 0, LF-2l0 (RD-450 Engine)
Page
2
DESCRIPTION . . , . ENGINE REMOVAL. ENGINE DISASSEM.BL Y Connecting rods and pistons . . . . . . . . . . . . . . . . . . . . . . . . . . . Cylinder head and valves . . . . . Flywheel and housing ..... Main bearings . . . Manifold Oil pump overhaul .. Rocker arms. . . . . . . . .. . . . . Water pump overhaul . . . . .
0
0
10
4-9
10, 11
10
12, 13
13, 14
3, 4
11, 12
15
15-17
17, 18
14, 15.
18
24, 25
21
23
18- 23
26
23
24
21
18-21
23
21
22
24
REPAIR OF SUB-ASSEMBLIES AND ASSEMBLING Camshaft bushings . . . . . . . . . . . . . . . . . . . . , . . . . . . . .

Connecting rods and pistons . . . Crankshaft, flywheel and camshaft inspection . . . . . . . . . . . . . . . . . . .
Cylinder block and sleeves, . . . . . . . . . . . . . . . .
Miscellaneous parts inspection . . . . . . , . . . . . . . . . . . . . . , . . . .
0 0
ASSEMBL Y OF ENGINE Accessories . . . , . . . . . . . . . Camshaft and gears Clutch . . . . . . . . . . . . . . .

Connecting rods and pis tons . . .
C r ankc as even tila tor. . . . . . .
Cylinder head . . . . . . . . . .
Engine mounting . . . . . . . .
Flywheel and housing . . . . .
Main bearings . . . . . .
Rocker arm assembly . . .
Tappets . . . . . .
Timing . . . . . . .
Valve adjusting.
PRINTED IN UNITED STATES OF'" AMERICA
ENGINES Specifications Page 1
SUPER BLACK DIAMOND 2H2 SLEEVELESS ENGINE

SPECIFICATIONS
Engines used in R-Line chassis are the same as used in L-Line trucks except the new BD-282 Super Black Diamond Sleeveless Engine has been added for the RF-170, R-180, RC-180 as standard equipment. The following chart lists specifications of this new engine . Engine . . . . . . . . . . . Number of cylinders .. Bore .. Stroke. Displacement (cu. in.) .. Rated H.P. (A.M.A.) .. Brake H.P. (maximum) At R.P.M. Brake H.P. (net). At R.P.M. . . . Torque maximum (lbs-ft). At R.P.M. Torque net (lbs-ft) At R.P.M. . . . . Maximum recommended speed R.P.M. Compression ratio. Firing order . -. . . . Crankcase refill capacity (qts) Weight (bare) (lbs.) . . . . . . . . Weight with standard accessories (lbs.) . . . Super Black Diamond 282 Sleeveless Engine
... 6
~-13/l6
.4-1/8 .282.546 .. 34.8 130.2 .3400 . 117.5 .3200 .246.3 .1800 238.2 .1600 .3400 . 6.5 1-5-3-6-2-4
. 7
742 831
CRANKSHAFT
Main journal diameter. Crankpin diameter Bearing clearance Crankshaft end play Trust taken by . . . . Hardening method. . .
ers
12-MARCH 1953 (Supplemental page, for
2.701 .2-1/8 .0013-.0043 .0055-.0145 . .. Rear . Through

erS-Ill.
PFlINT!:tI IN UNITED STATes OF AM!:RICA.,
ENGINES
Specifications Page 2
R-LiNE MOTOR TRUCK SERVICE
CAMSHAFT
Camshaft journal diameter: Front .. Second. Third .. Fourth . Camshaft bearing clearance. Camshaft end play Thrust taken by .. Camshaft gear backlash.
'.
1.8130-1.8145
1. 7248-1. 7263
1.7098 -1 .711 3 1.5010-1.5025 .0010-.0035 .0020-.0100 Thrust flange . . .0015 (desired)
CONNECTING RODS
Connecting rod bearing end clearance Connecting rod bearing clearance . . . .0070-.0130 .0007-.0032
PISTONS
Material. Recommended piston clearance .. .. Aluminum alloy .003
PISTON PINS
Length . . . . Diameter . Pin fit at room temperature (70 0 ): Recommended clearance in rod. Recommended clearance in piston. 3.201 .9193
..
. ..
. . . . . . . .. . . . . . . . . . . . . . . . . . .
.0003-.0005 .0001 tight . { .0003 loose
FEELER GAUGE RIBBON CHECKING

Width . . . . Thickness. Tension on scales (lbs.). Desired tension (lbs.) .. 1/2" .003 6-18 . . 12
R-LiNE MOTOR TRUCK SERVICE

PISTON RINGS
Compression rings: Number used on each piston.
ENGINE Sp e cifications Page 3
...... 3
Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
{{1(h3{;~
OIL RINGS
Number used on each piston. Size . . . . . . . . Ring diameter
. .. 1
3/16 3-13/16
RING GAP
Compression.
U -flex . . . . . .
. . 010-.026 .0,003-.027
FIT IN GROOVE
Compression top . Second and third.. Oil control fourth. .0025-.0040 .0015-.0030 .0015-.0035
VALVES
Stem diameter. Angle of face . Tappet clearance (hot). Stem clearance in guide. Width of valve seat . S10 Roto valve cap to stem clearance.
EXHAUST
.372
INTAKE
.372
.023 .003 5/64-7/64 .001-.005
.023 .002 3/64-5/64
VALVE TAPPET
Clearance in block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0015-.003
VALVE SPRINGS
Free length . . . . . Length valve open.. Pounds pressure - valve open. . . Valve Rocker Arm Clearance in Shaft
CTS 12-MARCH 1953 (Supplemental pages for CTSI1I.
. .. 2.187 . . . 1.468 . . 186-196 .0015-.004

PRINTED IN UNITED STATES OF AMERICA.
ENGINE Specifications Page 4
VALVE TIMING
Intake opens (before T. D. C.) .. Intake closes (after T. D. C.) .. Exhaust opens (before T. D. C.) . . . Exhaust closes (after T. D. C.) . . . Intake valve tim.ing checking clearance.
. . . . . . . . . . . . . . . .. .. ........
. . . . . . . . . . . . . . ... . . . . . . .
'"
.020
OIL PUMP
Body gear end clearance. Pum.p body to spiral gear clearance .. Pum.p shaft diam.eter . . . . . . . Pum.p shaft clearance in bore . . .0025-.0055 .0048- .0088 .4885-.4890 .005
OIL PRESSURE
Minim.um. 1bs.
At R. P. M . .
. 15-20 . Idling .40-45 .1200 and up
Maxill'lum. 1b s .
At R. P. M . . . .
ENGINE SPECIFICATIONS
CONT.
R-6602
6 4-7/8 11 5-/38" 602.00
ENGINE MODELS Number of cylinders . . , Bore . . . . . . . . . . , Stroke . . . . . . , Displacement (cu. in.). Rated h.p. (A.M.A.) . . . Brake h.p. (maximurn), . At r.p.m. . . . . . . . , Brake h.p. (net) . . . . . , , At r.p.m. . . . . . . . Torque maximum (lbs.ft.~ At r.p.m. . . . . . . . . . Torque net (lbs. ft.) . . . . At r.p.m. . . . . . . . . Maximum recommended speed r.p.m. . . . . . . , Governed speed r.p.m. . . Compression ratio . . . . , Firing order . . . . . , . . . Crankcase refill capacity (q ts.) . . . . . . . . .. Weight, bare (lbs.) . . . . . Weight, with standard accessories (lbs.). . . . CRANKSHAFT: Main journal diamBter. Crankpin diameter . . . Bearing clearance . . Crankshaft end play Thrus t taken by . . . . . Hardening method. . . . Main bearing bolt ten sion (ft. Ibs.) . . . . CAMSHAFT: Camshaft journal dia meter Front . . . . . . . . . . ' {
SD-220 6 3-9/16" 3-11/16" 220.50 30.4 100,0 3600 90 3600 173.5 2000 167 1200 3600
,
SD-240 6 3-9/16 11 4-1/64" 240.30 30.4 108 3600 93 3400 191. 9 1400 186 1100 3400 6,5 153624 7 607 673 2.748" 2.749" 2,373" 2.374" .0010" 0040" .005"-,013" rear interm. through 75-85
BD-269 6 3-9/16 11 4-1/2" 269.10 30.4 100,5 3000 88,6 2800 222.0 1600 216.5 1000 3000 6,3 153624 7 781 874 2.7005" 2.70 IS" 2.122" 2.123" ,0013" ,0043" .0055"-,0135" rear through 100-II 0
RD-371 6 4-3/8" 4-1/8" 372.06 45.9 143,8 3200 128 2850 282.5 1600 280.0 1000 2850 6,3 153624 9 937 1047 3.2495" 3.2505" 2.751" 2.752" ,0013" .0043" ,004"-.01211 rear tocco 100-1I0
RD-406 6 4-3/8 11 4-1/2 11 405.89 45.9 154,2 3200 138 2750 319.0 1200 313.5 1000 2750 6.3 153624 9 942 1076 3.2495" 3,2505" 2.751" 2.752" ,0013" ,0043" .004" -,012" rear tocco 100-110
RD-450 6 4-3/8 11 5" 450.99 45.9 162,2 3000 146 2600 358.5 1200 354.0 1000 2600 6,2 153624 9 948 1082 3.249511 3.2505" 2,751" 2.752" ,0013" .0043" .004"-.01211 rear tocco 100-110
r r
Z
tTl
3:
o --l o :;0
C
--l
153624 16 1638 1863 3.2491! 3,250" 2.999" 3,000" ,0022" 0046" ,006"-.008 11 front tocco 105-115
'U
6.5 153624 7 607 673
:;0
()
7\
(f)
<
z
tTl :;0
{
l
{
r
2.748" 2.749" 2.373" 2.374" .0010" ,0040" 005" -. 0 13" rear interm. through 75-85
n tTl
3:
::t>
C
::t> r
Ul
(l)
Second . . , . , , , . , {
2.109" 2,110" 2,089" 2.090"
2.109" 2.110" 2.089" 2.090"
1.811" 1.812" 1.577" 1.578"
2.109" 2.110" 2.089" 2.090"
2.109" 2.11 0" 2.089" . 2.090"
2,109" 2.11 011 2.089" 2.090"
2.1220" 2.1225" 2.1220" 2.1225"
\I)
",,Z "dQ(l ,.,. ......

""'Z
(l)
~t'l
O'Q
,...UlUl
g t'l
'1jtllM
C/Q
III '0
Il>
(1)
ENGINE MODELS Third . . . . . . . . , , Fourth . . . , . . . . . . Fifth . . . . . , . . , . Camshaft bearing { clearance, . . . , . , . Camshaft end play . , . { Thrus t taken by . . . . . { Camshaft gear backlash
SD-220 2.06.9" 2,070" 1.4995" 1.5005"

"
SD-240 2.069" 2.070" 1.4995" 1.5005"

.. . . . . . . . . . . . . . . 0 "
BD-269 1.562" 1.563 " 1.499" 1.500"

"' ...... 1>"" ......
RD-372 2.069" 2.070" 1.4995" 1.5005"

.. ............ "0.
RD-4.06 2.069" 2.070" 1.4995" 1. 5005"

.. .... " .... 0"""
RD-450 2,069" 2.070 11 1.4995" 1.5005"

0.00
CONT. R-6602 2.1220" 2.1225 11 2.1220" 2.1225" 2.1220" 2.1225" .0015" .0025" .0050" .0070" Thrust Flange .0015" (desired) .0060" .0100" .0012" .0036" 100-110 aluminumalloy
N~Z
n 0 ....1-<
III til
() M
c:
o
:::l
Ul
..... " .........
.0010" 0035" .0020" .0080" Thrust Flange .0015" (desired) .0070" 0 13" .0011" .0011" 45-55 aluminumalloy .003 2.950" .8748" .8750" .0002" .0004" .0000" .0002"
, 00 10" .0035" .0020" .0080" Thrus t Flange .0015" (desired) .0070" .013" .0011" .0032" 45-55 aluminumalloy .003 2.950" .8748" .8750" .0002" .0004" .0000" .0002"
00 10" .0035" .0020" .0080" Thrust Flange ,0015" (desired) .0070" .0130" 0007" .0032" 60 70 aluminumalloy .003 2.950" .9192/1 91 94" .0003" 0004" .0000" .0002"
.0010" .0035 11 .0020" 0080" Thrust Flange .0015" (desired) .0070" .0130" .0012" .0037" 75-85 alum.inum 'lHoy .003 3.796 11 1.1089" 1.1091" .0005" 0006" .0000" .0002"
00 10" .0035" .0020" 0080" Thrust Flange .0015" (desired) .0070" .0130" .0012" .0031" 75-85 aluminumalloy .003 3.796" 1.1089" 1.1091" .0005 11 .0006 11 .0000" .0002"
00 I 0" .0035" .0020" 0080" Thrust Flange .0015" (desired) .0070" .0130" .0012" .0037" 75-85 aluminumalloy .003 3.796. ' 1.1089" 1.1091" .0005" 0006" .0000" .000211
r;
C
(T1
s:
o --l
o
:::0 --l :::0 C
()
CONNECTING RODS: Connecting rod bearing { end clearance . . . . Connecting rod bearing { clearance. . . . . . . . Connecting rod bolt nut tension (ft. lbs.). , . . PISTONS: Material . . . . . . . . . { Recommended piston clearance: PISTON PINS: Length . . . . . . . Diameter . . . . . . . . { Pin fit (room tempera ture70 0 F.): . r Recom~ended clear { ance in rod. . . . Recommended clear ance in pis ton. . . L
7\
[T1
en
:::0
() [Tl
<
1.4998" 1. 5000" .0003" .0007" 000 1" - tight . 000 111 -loos e
s: z c r
FEELER GAUGE RIBBON CHECKING: Width . . . . . . . . . . . . Thickness . . . . . . . Tension on scales (lbs.) Desired tension (lbs.) .
1/2" ,003" 6-18 12
1/2" . 0 03" 6-18 12
1/2" .003" 6-18 12
1/2" .003" 6-18 12
1/2" . 003 11 6-18 12
1/2" . 003 11 6-18 12
1/2 11 005" 5-10 8
ENGINE MODELS PISTON RINGS: COlTIpression Rings: Ntunber used on each pis ton, Size. . . . . . Oil Rings: Ntunber used on each piston, . . Size . . . . . Ring dialTIe ter Ring Gap: COlTIpression, U-F1ex . , , Fit in Groove:COlTIpression - top, , { - 2nd &: 3rd , , , . { Oil Control - fourth { Plain - fifth, , , {
SD-220
SD-240
BD-269
RD-372
RD-406
RD-450
CONT. R-6602
3 1-3/32 11 2-1/S"
3 1-3/32 11 2-1/S I1 1 3/16" 3-9/16" ,016" -.026" 00025 '1 .004011 ,0015 11 ,0030" .0015 11 .00351 '
3 1-3/3211 2_1/S II
3 1-3/32 11 2-1/S 11
3 1-3/32" 2-1/8"
1-3/32 11 2-1/8"
1
1 3/16" 3-9/16 11
. 0 16" -. 026" ,0025" ,0040" .0015 '1 ,0030" ,0015 11 ,0035"
1 3/16 11 3-9/1611
,016" -,026" ,0025" ,0040" .0015" .0030" .0015" .0035 11
1
3/1611 4-3/8" ,025" -, 035 ,0040 '1 00055" .0020 '1 .0035" ,0015" .0035"
11
1
3/16" 4-3/8" ,025" -.035"
3/1611 4-3/8 11 .025"-.035" ,0040" ,0055" ,0020" .0035" .001511 .0035" .013" -,023" ,0055" .0070" ,0025" ,0035" .0015" ,0035" .0015" ,0035"
r
(TJ
,004011 ,0055" ,0020" ,0035" ,0015" ,0035 11
~ o :::0
-l
3:
n
A
:::0 C
(f)
INTAKE VALVES: StelTI dialTIeter . .372" .372" ,342" A34" .434" .434" .4973 11 Angle of face . 30 3 45 15 15 0 15 30 Tappet clearance ,018"-.020" 1.018,,-.02011 I,OIS"-,020 11 I,OIS II -,02011 1,018"-,02011 1,018 11 -,020" .020" StelTI clearance in guide ,0015 1' -.0035" ,0015 1' -.0035" ,0015"-.0035" ,0015"-.0035" .0015"-.0035" .0015"-.0035" ,0008"-,0021" Width of valve seat. . . 1/64"-3/64" 1/64"-3/64" 5/64"-7/64" 5/64"-7/64" 5/64" -7/6411 5/64"-7/64 11 1/16"-3/32"
(TJ
:::0
n (TJ
<
EXHAUST VALVES: StelTI dialTIe ter, , . Angle of fac e, , . . Tappet clearance (hot). StelTI clearance in guide Width of valve seat . Slo-roto valve cap to
s telTI clearance . . VALVE TAPPET: Clearance in block, VALVE SPRINGS: Free 1enght: Inner. Outer. , ..
.370" 300 ,018 1' -.020" ,002" -.004" 3/6411 -5/6411
.370" 30 .018"-.020 11 .00211-.004" 3/6411 -5/64"
,341" 45 .018 11 -.020" 002" -,004" 5/64"-7/641f
.434" 45 .018"-.020" . 002 11 -.00411 3/3211 -1 .002"-,006 11
.434 11 45 ,018" -,020" .002 11 -,004" 3/32"-1 ,002" -, 006'1 .00 I" -. 003"
,434" 45 ,018"-.020" .002" -.004" 3/32"-1/8" , 002" -, 006" ,001"-,003"
,494" 45 .020" ,0035 11-.00511 5/64"-7/6411 . 002" -.006"

,0019" -.0002"
z
c
3:
r-
. 00 1511 - . 003 11
,0015"-,003"
.0015"-.003"
.001" -, 003"
'tl
(b
VI
2-11-16"
2-11/16 11
2-33/6411
2-11/32 2-9/16 1 '
11
2-11/32 2-9/16"
11
2-11/32" 2-9/16"
2-3/4 2-13/16"
11
OQ
(b
P'<"'"H
'U~o
.....
. . z
~M
gM
WUlVl
'ljClltr1
1Il'd
OQ('I)Cl ('I) H
C.
""t!!Z
ENGINE MODELS Length - valve open: Inner . . . . . . . . Outer . . . . . . . . Lbs. pressure - valve open: Inner . . . . . . . Outer . . . . . . . . . VALVE ROCKER ARM { CLEARANCE IN SHAFT VALVE TIMING: Intake opens (before T.D.C.) . . . . . . . Intake closes (after L.D.C.) . . . . . Exhaus t opens (before L.D.C.) . , . . . . . Exhaus t closes (after T.D.C.) . . . . . . . Intake valve tiITling clecking clearance . OIL PUMP; Body gear end clear ance . . . . . . PUITlP body to spiral gear clearance . . . PUITlP shaft diaITleter . . { PUITlP shaft clearance in bore , . . . OIL PRESSURES MiniITlUIT1 (lbs.) . . At r.p.ITl . . . MaxiITlUIT1 (lbs.) . . . At r.p.ITl . . . . . CYLINDER HEAD: Cylinder head bolt (ft. 1bs.) . . . . . . . SD-220 1.683" SD-240 1.683 11 BD-269 1.668" RD-372 1.503" 1. 7 06" 83-88 133-141 ,0015" .004" RD-406 1.503" 1. 7 06" 83-88 133-141 ,0015" 004" RD-450 1.503" 1.706" 83-88 133-141 .0015" .004" CONT. R-6602 1.750" 1. 7 50" 82-88 160-170 ,0002" .0014"
l::I
(Il
~CIl ....
n tr1
........
141-149
..........
141-149
.......
103-111
0
.......
.0015" 0 04"
...........
r;
C z (Tl
.0015" 004"
.0015" 004"
10 46 48 8 .023"
10 46 48 8 .023"
5 45 40 10 .023 1t
8 52 55 15 .023"
8 52 55 15 ,023"
8 52 55 15 ,023"
12 62 54 20 ,020"
:::: o -1
o :;;0
C
:;;0
() ~
{j) (Tl
-1
:;;0
<
:l>
.0025" -,0055
11
,0025" -.0055" .0025"-.0055" 0025" -.0055" 0025" -.0055" 0025" -,0055"
(Tl
n
:l> r
.........
.4885" .4890" ,005" 15-20 idling 40-45 1200 up
. ......
.4885 .4890"
11 -
.03125" ,4985" .4992" .005" 15-20 idling 40-45 1200 up
.03125" .4985" .4990" .005" 15-20 idling 40-45 1500 up
.03125" .4985" .4990 fl 005" 15-20 idling 40-45 1500 up
.03125" .4985" .4990" .005" 15-20 idling 40-45 1500 up
z c
,005" 15-20 idling 40-45 1200 up
85-95
85-95
75-85
100-110
100-110
100-110
100-110
SILVER DIAMOND ENGINE
SIZE AND THREAD
NAME OF ASSEMBLY Generator s trap to generator . . . . . Water outlet . . . . . . . Coil bracket to cylinder head . . . Fuel pump to crankcase . . . . . . . Oil pan to crankcase . . . . . . . . . . . Distributor adapter to crankcase . . . . Oil pump cover to body . . . . . Vibration damper to pulley. . ... Oil pump body to crankcas e . . Generator mounting . . . . . . . . . Coil mounting . . . . . ' . . Manifold to cylinder head, . . . . . . Engine support bracket to cr'ankcase . . . Generator bracket to crankcase . . . . . Intake to exhaust manifold . . Water pump to crankcase . . . . . . . . . . Cylinder head cover . . . . . . . . . . Gear case cover to cr~nkcase . . . . . . . Camshaft thrus t flange . . . . . . Connecting rod bolt . . . . Carburetor to manifold . . . . . . . Intake to exhaust manifold . . . . Gear case cover to plate . Flywheel housing . . . . . Oil pressure relief valve. Flywheel to crankshaft . . . . . Starting motor . . . . . . . . . Cylinder head capscrew. . . . . . . Crankshaft bearing bolt . . . . . . . . Starting crank nut. . . . Camshaft lock nut. . . . . . Spark Spark Spark Spark Spark plug plug plug plug plug (in (in (in (in (in cas t iron) cas t iron) aluminum) cast iron) aluminum) . .. . . ...
RECOMMENDED WRENCH TORQUE LOAD, FT.-LB.
5/16 5/16 5/16 5/16 5/16 5/16 5/16 5/16 5/16 5/16 5/16 3/8 3/8 3/8 3/8 3/8 3/8 3/8 3/8 3/8 3/8 3/8
18 18 18 18 18 18 18 18 18 24 24
14 8 14 8 14 14 14 16 14 8 16
25 25 25 25 25 25 25 25 45 23 23
- 16
- 10
- 16
- 10
- 16
- 16
- 16
- 18
- 16
- 10
- 18
30
30
30
30
30
30
30
30
55
28
28
16 16 16 16 16 16 16 16 24 24 24
5/16 - 24
9 - 11
50 - 60 13 - 15 55 - 65 75 - 85 85 - 95 75 - 85 90 - 100 110 - 120 32 25 21 28 25 35 28 25 31 28
7/16 - 14 7/16 - 14 7/16 - 20

1/2 - 13 1/2 - 13 1/2 - 13
1 - 14
1 - 20
7/8 - 18 14 MM 14 MM 18 MM 18 MM
PfUNTEO IN UNITED STATES OF AMERICA
SUPER BLUE DIAMOND ENGINE
SIZE AND THREAD

5/16 5/16 5/16 5/16 5/16 5/16 5/16 5/16 i8 18 18 18 18 24 24 24 16. 16 16 16 16 16 16 16 16 24 24
NAME OF ASSEMBLY Air cleaner to cylinder head . . . . Fuel PUInp to crankcase . . . . . . . Crankshaft rear oil seal, upper . . . Distributor bracket to cylinder head . Oil pUInp cover to body . . Vibration damper to pulley. . . . . . . . Gear ca.se cover to plate . . . . . . Generator mounting . . . . . . . . Manifold to cylinder head . Oil pan to crankcas e . . . . . . . . Generator bracket to crankcase . . . Oil pump body to crankcas e . . . , . ,'. Water PUInp to cylinder head . . . Crankshaft rear oil seal, lo,wer . . . . Gear case cover to crankcase . . . . . . . , Cam shaft thrus t flange . . . . . . . . . Star ting mo tor. . . . . . . . . Carburetor to manifold. . . . . . G ear cas e c over to pIa te . . . . . . . Oil pressure relief valve . . . . . . . C onnec ting rod bolt. . . . . . . . . . Intake to exhaus t manifold . . . . . . Connecting rod bolt . . . . . . . . . . . Flywheel housing . . . . . . . . . . . . Cylinder head cap screw . . . . . Flywheel to crankshaft . . . . . . . . . Crankshaft bearing capscrew . . . . Crankshaft bearing caps crew . . . Camshaft lock nut. . . . . . . . . Spark Spark Spark Spark Spark plug plug plug plug plug (in (in (in (in (in cas t iron) . . . . . . cas t iron) . . . . . . . . alUIninUIn) . . . . . . . cas t iron) ~ . . ...... alUIninUIn) . . . . . . . .
RECOMMENDED
WRENCH TORQUE
LOAD, FT.-LB.
18
8
14
14
14
16
-
22
10
16
16
16
18
8
- 10
8
- 10
30
30
30
30
30
30
30
30
30
28
3/8 3/8 3/8 3/8 3/8 3/8 3/8 3/8 3/8 3/8 3/8
25
25
25
25
25
25
25
25
25
23
13 60 55 60
. 9
- 11
- -15

- 70
7/16 - 14 7/16 - 20 7/16 - 20 7/16-20

1/2 - 13 1/2 - 13 1/2 - 20
- 65

- 70
75
- 85
75
- 85
90
- 100
9/16 - 12 9/16 - 12
1 - 20
100
- no 100
- 110
110
- 120
32
25
21
28
25
35
28
25
31
28
7/8 - 18 14 MM 14MM 18 MM 18 MM
SUPER RED DIAMOND ENGINE
SIZE AND THREAD
NAME OF ASSEMBLY Dis tributor bracket to cylinder head

Crankshaft rear oil seal, upper . . .
Crankshaft rear oil seal, lower ..
Generator mounting .. , .
Carbu.retor to manifold (Holley)
Starting motor mounting . . Oil pump body to crankcase Camshaft thrust washer . . . . Damper to pulley hub . . . . . Fuel pump to crankcase . . Rocker arm bracket to head .. Gear case to crankcase . . . . . . . . Generator bracket to case . . . . Water pump to cylinder head . Oil pan to crankcase . . . . . . . . Oil filler. . . . . . . . . . . . , . , . . Gear case cover to crankcase plate . . Carburetor to manifold (Zenith) . Gear case cover . . . Manifold to cylinder head . .
RECOMMENDED
WRENCH TORQUE
LOAD, FT.-LB.
5/16 5/16 5/16 5/16 5/16 3/8 3/8 3/8 3/8 3/8 3/8 3/8 3/8 3/8 3/8 3/8 3/8 3/8 3/8 3/8 7/16 7/16 7/16 7/16 1/2 1/2 1/2 1/2 1/2 9/16 9/16 9/16 9/16
18 18 18 24 24 16 16 16 16 16 16 16 16 16 16 16 24
18 18 18 20 20 25 25 25 30 25 25 25 25 25 25 25 25 23 23 23 55 55 75 40
22 22 22 24 24 30 30 30 35 30 30 30 30 30 30 30 30 28 28 30 65 65 85 45
24
24 24 20 20 20 20 13 13 13 13 13 18 18 18 18
Intake to exhaus t manifold .

Intake to exhaus t manifold. , . . . . . .
Connecting rod capscrew (place type).
Carburetor to manifold. . . . ..
Oil filter mounting. . . . . . . ..
Cylinder head capscrew, oil. . . .
Cylinder head caps crew, long . . . .
Cylinder. head caps crew, short . .
Flywheel housing to crankcase
Crankshaft Crankshaft Crankshaft Crankshaft to flywheel. .
to flywheel .
bearing cap.
bearing cap.
75 - 85
100-110
100 - 110
100-110
75 - 85
150 - 160 150 - 160 100-110 100 - 110 110 - 120 32 25 21 28 25 35
28
25
31
28

1 - 20
Camshaft gear nut .

Spark Spark Spark Spark Spark plug plug plug plug plug (in (in (in (in (in cast iron)
cast iron) .
aluminum).
cast iron)
aluminum).
7/8 - 18 14 MM 14 MM 18 MM 18 MM
PRINTED IN UNfTEO STATES OF AMERICA
ENGINES Silver Diamond Section A Page 1
SILVER DIAMOND ENGINE
Fig. I - Silver Diamond Engine
PRINTED IN UNITED STATES Of" AMRICA
Gl C
t:ft
UJ
-c
c
e ta
o
L..
Gl
>
..... o
.>
<0
~ Gl
t:ft

DESCRIPTION
General
The Model SD engine is a 4-cycle, 6-cylin der-in-line, overhead-valve-type engine (Fig. 1 and Fig. 2). The engine serial number is stamped on a pad at the front on the right side of crankcase just below the cylinder head. The block does not have replaceable liners for the cylinders. The detachable cylinder head con tains all valves, valve guides, and springs. The cylinders are numbered from front (fan and timing gear end) to rear. Engine crank shaft rotation is clockwise as viewed from the front end of the vehicle. The intake and ex haust manifolds, carburetor, starter, and gen erator are located on the right side of engine. The ignition coil, distributor, fuel pump, oil pressure regulator, and breather are located on the left side of engine. The oil fille r inlet is located in the valve cover on the top of en-
gine. The bayonnet type oil level gauge is located on the left side of engine. The water pump is located at the front of engine.
Construction
1. The generator, fan, and water pump are driven by a V-type belt from a driven pul ley mounted on the front end of crankshaft. The distributor, mounted at the left side of engine, is driven by the camshaft through the oil pump. 2. The exhaust and intake manifolds are bolted to each other and to the right side of the engine head. The intake manifold and the exhaust manifold are each cast in one piece. 3. A vibration damper is provided at the ,front end of the crankshaft on the model SD-240 engine only.
e:i;J~~~~~~---- Cover capscrew

Rocker arm Retainer Lock---- Spring ----....lIIl!!III!'!~1
1:. .- -
shaft Rocker arm cover Sleeve dowel Cover gasket
.:-....---Valve guide
!;.!!!!!!;,..~--- Valve
'...!...._-- Valve seat
Push rod
E4f.---Seal ring
Connecting rod
A.21930
Fig. 3 - Sectional view through engine showing details of valve mechanism.

PRINl'EO IN UNITED STA"rEs OF AMERICA
4. The cylinder block and crankcase are cast in one piece, and carry the crankshaft main bearings. Water circulation pas sages completely surround the cylinders in the crankcase, and also provide coolant to the cylinder head. 5. Oil is supplied under pressure by the oil pump to the engine lubrication system. Oil spray from the revolving cranksahft is distributed to the cylinder walls, pistons, and other moving parts inside the engine. 6. Exhaust valve seats are of alloy, and are pressed into place (Fig. 3). These valve seats lengthen the period between valve reconditioning operations. Valves and valve seats are cooled by continuous cir culation of water through the cylinder head.
Fig.
ij -
Removing Silver Diamond Engine.
7, The detachable cylinder head is bolted to the crankcase, and a gastight and water tight seal is maintained by means of a gasket.
8. The crankshaft is a drop forging of heat treated steel. It is counterweighted, bal anced both statically and dynamically, and ground to close limits. The shaft is mounted in four precision-type replace able shell bearings, the number three bearing taking up the thrust. 9. The pistons are made of an aluminum al loy, are cam ground, and are fitted with three compression rings and one oil con trol ring. The full-floating type piston pins are held in place in the pistons, at the ends of the pins, by snap rings. 10. The camshaft is machined from a solid drop forging and mounted in four special replaceable bearings. 11. The flywheel is bolted and doweled to the crankshaft flange. The timing mark is lo cated on the flywheel.
2. Disconnect upper and lower radiator hose connections. 3. Disconnect engine circuit wiring. This includes coil wire, starter cable, engine ground strap, and instrument sender unit wires. 4. Disconnect fuel line at fuel pump. Discon nect throttle control linkage at left side of engine and remove choke at carburetor. 5. Disconnect clutch linkage at bell housing. 6. Remove engine rear mounting bolts from both sides of engine support pads. 7. Remove engine front mounting bolts from support bracket; these are the bolts at the front crossmember. NOTE: The engine front support bracket is removed with the engine. 8. Remove radiator mounting bolts, and lift out radiator support and core assembly. 9. Disconnect engine exhaust pipe at mani fold.
ENGINE REMOVAL
The engine, with transmission removed, can be lifted from chassis, without disturbing the fender and grille assembly by using a suit able chain sling and a floor crane (Fig. 4), Dis connect the following electrical circuits, hose connections, and various units as outlined:
ENGINE DISASSEMBLY
Install the engine in a suitable rotating engine overhaul stand. NOTE: Many of the disassembly operations can be performed with the engine in the chassis. However, the fol lowing disassembly outline is performed with the engine removed from the chassis to clear ly illustrate each of the units. Except where indicated, no attempt has been made to pre scribe a particular sequence for removing the various units, since some can be readily re moved with the engine in the chassis. The ex tent of the service required on a particular unit will govern the necessity for its removal.
1. Drain engine oil pan. Drain all coolant from engine cooling system by opening the drain cock on side of engine as well as the radiator drain cock.

Removing Rocker Arms
The following steps are to be followed when removing the rocker-arm cover and rocker arm assembly. (Carburetor and air cleaner previously removed): 1. Remove three capscrews from rocker-arm cover. Remove air cleaner line and re move cover (Fig. 5).
Rocker-Arm and Valve Mechanism

Disassembly
1. The rocker-arm assembly is composed of

front and rear shafts joined at the center, on which are mounted twelve rocker arms and six tension springs (Fig. 8). The shafts are mounted in seven brackets, and are prevented from turning at the two end brackets by slots in the shaft into which the cylinder-head bolts fit.
~iitIJI,tr.>itA~,~
. . "'. , . .
Rook" -
J7
~"mW'
...
-.~~v~v
Brackets
Sleeve dowel
Tension springs
A-21909
Fig. 8 Fig. 5
2.
Remove capscrews from shaft brackets (Fig. 6).
2. Number two, four and six rocker-arm brackets have sleeve dowels which keep the rocker-arm assembly aligned.
3. These sleeve dowels measure approxi mately 5/81! in diameter, I" long, and 1/32" wall. 4. The three hold-down brackets are reamed, from the bottom side (Fig. 9) so that the sleeve dowels willfit .0005"-.0035" tight in brackets. About one-half inch of dowel is in the bracket. The remaining half of dowel is fitted .0025 11-.0055" loose in the head. When removing rocker-arm assem bly the dowels will remain in hold-down brackets.
Shaft brackets
F j g. 6
3. Remove rocker-arm assembly as a unit (Fig. 7).
Rocker arm assembly
Sleeve dowel
A-21938
Fig. 9 - Oetai Is
bracket.
of sleeve
dowel
located in
5. Separate the shafts and slide rocker arms, springs, and brackets from shafts. 6. Clean all parts in a solvent cleaning fluid, being careful to clean all ac(mmulated sludge and carbon deposits from oil holes and slots.
PRINTED IN UNITED STATES OF' AMERICA

H - - - Press
Rocker Arm Inspection

Carefully inspect all parts for defects and
wear:
1. Inspect rocker-arm shaft expans ion plugs. Check ona surface plate for signs of bend
ing, check for wear from rocker arms. If
a shaft is bent or shows perceptible wear,
it must be replaced.
2. Inspect rocker-arm adjusting screws for wear at contact surface and for thread wear. Replace worn screws. Check rock
er-arm bushings for wear. If clearance on shaft exceeds .004", replace bushings. Inspect valve stern contact pad surface of rocker arms, and resurface if wear is perceptible.

ram
a<o!;'--- Bushing
installing tool
3. Inspect tension springs for breakage or

loss of tension. Replace defective springs. Remove valve lifter rods.
Fig. 11- Installing new rocker arm bushing.
Re-bushing Rocker Arms

With properly fitting adapter, press old rocker-arm bushing from rocker arm (Fig. 10). Place new rocker-arm bushing in posi tion. Align oil hole in bushing with oil hole in rocker arm, which is located 23 0 from top of rocker arm toward rocker-arm adjusting nut. Use an installing tool and press new bushing into rocker arm (Fig. 11). Burnish bushing into place in the rocker arm (Fig. 12), then ream rocker-arm bushing to provide ,0015 11 .004 11 clearance.
....:'----Burnishing tool
Fig. 12 - Use SE-93 I Burnishing bar.

, . . - - Press ram
Cylinder Head and Valves

The following instructions are to be fol lowed when reconditioning cylinder head and gasket. Remove push rods, remove cylinder head bolts and lift off cylinder head and gasket (Fig. 13). Place cylinder head on bench.
Spark plugs
. . . , - - - - - Bushing removing tool
Rocker arm
Press plate
Fig. 10 - Use SE-1036-1 Bushing Removing Tool when removing the rocker arm bushing. Support the rocker arm on the SE-1033 support block. Select a bole in the support block to properly support the rocker arm at the same time permit the bushing to clear the support block when being removed. Use the support block when in stall ing and burnishing the new bushing.
Fig. 13

1. Compress valve spring with a valve com pressor and remove valve spring retainer locks (Fig. 14). Remove retainer. Re move valve spring and damper and separ ate valve spring damper from valve spring. Note that valve springs can be installed with either end toward the cylinder head. Remove all valve springs as outlined, and remove valve spring damper from each spring (Fig. 15).
2. Inspect exhaust valve seat for loose ness and inspect for exce width of valve seat surface. 1 rings are loose, re place. 1 a seat has been previously ground to such extent that it cannot be narrowed from top to bring to proper position near center of valve face, the must be re places.
Inspection of Valve Guides, Valve Springs, and Valves

1. Clean valve guides with a suitable clean ing tool. Check each valve guide with a tlGo and No-Go" gauge, if available; other wise, use a new valve to check fit. 1 'IINo_ Go" portion of gauge enters, the guide must be replaced. Recommended valve stem to valve guide clearance is from .0015 11 to .0035 11 for intake valves, and from .0021t'to .004" for exhaust valves. Clearance in excess of .006" for intake valves or .008" for exhaust valves, require guide replace ment. Valve guides are reamed to .3743" .3758 11 after assembly in cylinder head.
Fig. IIj.
2. Test valve springs with damper in posi tion. Test tension of each valve spring at valve open length with a valve-spring test er (Fig. 16). Check valve springs at 1-11/16 11 length, and replace if pressure is less than 149 Ibs.
Valve spring
Damper
A.21939
Fig. 15 - Dampers are used at all the valves. Assemble damper, spring and retainer as shown.
2. Invert cylinder head. Remove all valves from their valve guides and from the head.
~----Valve
spring
3. Scrape all carbon from cylinder-head combustion chamber, and clean any gasket rna terial from surface of head. Clean the head using steam cleaning or other suit able cleaning equipment 4. Clean all carbon deposits from valve heads and valve stems with a wire brush. Wash all valve springs and retainers in clean ing solvent.
1Ii~"-~r---T--- Scale (pounds)
A.21890
Inspection of Cylinder Head

1. Inspect cylinder head visually for signs of cracks or sand holes. If found defective, weld or replace head ..
PAINTO IN UNITED STAT$ Of' .... ERICA
Fig. 16 - Use SE-1565 Valve spring testing tool or similar tool to check spring tension.
3. Inspect each valve for warpage, :Cor severe ly burned condition, and for excessive grinding on the valve head. Inspect valve stem for scuff marks or perceptible wear.

be dressed before starting a reconditioning job. You will be unable to determine how closely the angle of the seat will match the valve face until the valve and seat have been ground and a check made with a very light tint of Prussian blue. If a full seat-width contact around the entire circle of seated valve is not shown, the angles do not match. It will then be necessary to redress the valve seat grinding stones, changing the angle sufficiently to correct the error. The correction should be made on the valve seat, and not Q.!! the valve. No more material should be removed from the valve face than is necessary to true it up and remove the burned or pitted portion. New valves should not be refaced, but should be checked for true ness. When a satisfactory match of valve seat and valve face angles has been obtained, the adjustment of both the valve refacer and the seat grinder should be locked in position, in order to eliminate this trial-by-error method on additional valves having the same angle .
Inspect valve stem end for wear at contact surface with valve rocker arm. If valve is warped, excessively burned, or has been previously ground to extent that valve head is thin at edge. replace valve; otherwise, valve can be reconditioned and reinstalled.
Repair of Cylinder Head

1. If cylinder head has to be resurfaced, re move only enough material to true-up surface. 2. If any valve guide shows excess clearance or"" out-of-round condition, press guide from cylinder head with a special remov ing tool (Fig. 17). Install new guide, and press into cylinder head until approxi mately 1-11411 remains above the top sur face of cylinder head (Fig. 18). Check valve guides after installation to .3758 1t to . 3743 11 with "Go and No-Go!! gauge. Ream valve guides to .3743 11 -.3758't after assem bly in cylinder head. 3. If an inspection has indicated the necessity, replace the valve seat. 4. Grind the valve seats in cylinder head to 30 0 on exhaust and 30 0 on intake.
Valve Seats
The primary purpose of a valve seat is to seal the combustion chamber against pressure losses and to provide a path to dissipate the heat accumulated in the valve head so as to prevent burning of the seat and warping of the valve head. The location of the valve seat on the valve face and its width controls the amount of valve head that protrudes into the combustion cham ber. It is obvious that the greater the expo sure within the combustion chamber, the higher the valve temperature; or in other words, the more heat it will collect. High valve tempera tures and poor heat dissipation also produce excessive valve stern temperatures and hasten the accumulation of carbon on the stern, caus ing them to stick in the guides.
Reconditioning Valves and Seats

One of the principal difficulties experienced in reconditioning valves is obtaining nearly identical angles on the valve seat and valve face. The importance of these angles in the grinding operation cannot be overemphasized, because it is impossible to produce a flat or square seat by lapping. The grinding stones on both the valve refacing machine and valve-seat grinder should
Press ram
Press ram
-A:
JIll
j
Valve guide remover -~..
f
Valve guide
Valve guide replacer
V':SDd" "'ad
Fig. 17 - Use SE-I722 Valve stem guide tool.
Fig. 18 - Using SE-1723 Guide replacer. gu i de down unti Ito(),I" bottoms on head.
Push

Valve Seat Widths
In general, the width of exhaust seat should range between the average and maximum spec ifications and the intake seats between the minimum and average specifications. The in take seats may be narrower than the exhaust because they are usually larger in diameter, thus providing a total seat area approximately equal to smaller exhaust valve with the wider seat. Also the less severe heat conditions do not require as large a seat area for heat dissi pation purposes. There are also objections to an excessive ly wide seat, a few of which are as follows: 1. In city or light delivery service a wide seat collects carbon and particles of dirt that will produce variations or loss of compression, resulting in poor idle and possibly a loss of general performance and economy.
2. A wide seat in severe service operating in the presence of dirt or an excess of car bon will produce a badly pitted seat which may be just as detrimental to valve life as a too narrow seat. Under these conditions a seat width to the minimum limit would possible be better; however, the source of trouble (which is the dirt and excessive carbon) should be eliminated, making it possible to retain the wider seat.
face, and tap valve lightly to its sea,t. NOTE: This is merely for test and proof of re suIts of refacing and re seating ope r ations. A poor grinding job cannot be cor rected by valve lapping. 5. Inspect each valve coated with blue for seat position. The seat should be at the approximate center of valve face, 3/64" 5/64 11 wide for exhaust, and 1/64 1t -3/64" wide for intake (Fig. 19).
Valve guide --~ Exhaust valve -;--r;;;.~5;:;;t--lntake
valve
A-:21889
Fig. 19 - Diagram showing valve installation.
Valve Assembly
1. Wipe valve faces and valve seats with a cleaning solvent to remove all dirt or for eign material. Coat valve sterns and valve faces with oil, and install valves in same seats to which they were checked. 2. Install valve springs with dampers. Com press valve springs with a valve spring compressor, and install valve spring re tainers and retainer locks. Be sure that retainers and locks are correctly seated. When overhauling engine with head and pan removed, the following procedures are recom mended: 1. Remove front motor to frame bracket by removing two nuts on top side (Fig. 20). Remove fan drive pulley nut and washer from end of crankshaft. Install puller and remove crankshaft fan drive pulley from crankshaft (Fig. 21). Remove 4 capscrews holding motor mounting bracket to block (Fig. 22). 2. Remove nuts and capscrews from engine gear case cover, remove gear case cover and gasket. Remove crankshaft oil slinger from end of shaft (Fig. 23). 3. Remove two self-locking capscrews from camshaft retainer thrust flange plate, working through two holes in camshaft gear (Fig. 24). Pull camshaft and gear assembly from cylinder block. Remove
Valve Seat Inserts

Necessity for replacing valve seat inserts should be very rare; however, if a replace ment is made it is important that new inserts be peened securely in place, using either in sert peening tool or a dull-pointed chisel, 1/411 wide, to peen cylinder head metal over outer edge of valve seat insert. Valve available. seat insert installing tools are
Valve seat inserts supplied for service are standard size and .030" oversize which permits a tight fit in cylinder head.
Repair of Valves
1. True-up the ends of valve stern against face of grinder. Remove only enough ma terial to true the surface.
2. Reface exhaust valves to 30 0 The valve face and valve seat angle must be identi cal.
3. Reface intake valves to 30 0 seat being the same. with valve
4. Place valves in cylinder head. Place a thin coat of Prussian blue on each valve
PRINTED IN UNITF"O STATe'S 0':-- AMRICA
ENGINES Silver DiaInond Section A Page 10

toward top of block, but first reInove ridge froIn top of cylinder wall, if any. Lift piston and connecting-rod asseInbly froIn top of cylinder block (Fig. 27). Replace cap on connecting rod. ReInove the re Inaining pistons, following the saIne pro cedure.
two capscrews holding the gear case cover J?late to block; reInove plate and gasket (Fig. 25). ReInove crankshaft tiIning gear, using a special gear puller (Fig. 26). (NOTE: Lubricate puller screw to pre vent daInage to screw threads). Turn engine in the overhaul stand and pro ceed with disasseInbly as follows: 4. Each connecting rod is nUInbered as to its position in the engine and these nUInbers are located on the caInshaft side of the engine. ReInove self-locking capscrews froIn connecting-rod cap and reInove cap. Push connecting-rod and piston asseInbly
Note that the connecting-rod caps are aligned with the rods by Ineans of tongue and groove construction (Fig. 28).
...
Front motor mounting support
.......
Crankshaft vibration damper

A.21940
Fig. 23 - Gear case cover ing gear details.
removed showing tim
Fig. 20
-_I..,.,.. __-,---
Fig,21 Fig. 2~ - Timing gear timing marks and camshaft thrust plate details.
Capscrews
Fig. 22
Fig. 25 - Camshaft and cover plate removal.
A.21944
Crankshaft timing gear

A21936
Fig. 26 - Crankshaft gear puller SE-1715 is installed with puller plates in position shown. Lubricate puller screw thoroughly. Fig. 29 - Use SE-1719 Bearing remove rear main bearing cap. cap puller to
6. With crankshaft securely clamped in vise, remove the six self-locking capscrews holding flywheel to crankshaft (Fig. 30). Tap flywheel with a soft hammer to loosen it from crankshaft; remove flywheel with ring gear assembly.
Fig. 27 - Remove cyl inder block.
piston
and
rod
from top of
Tongue
Fig. 30 - Remove self locking capscrews to move f I ywhee I

7.
A-21924
re
Fig. 28 - Connecting rod caps are al igned by means of tongue and groove construction.
5. The crankshaft bearing caps are numbered to identify thei r position and they must be reinstalled in their respective positions. Remove self-locking capscrews from each bearing cap. Remove all crankshaft main bearing caps. NOTE: To remove the rear, or No.4, main bearing cap, a puller is re quired (Fig. 29). After all caps have been removed, lift crankshaft straight up and out of cylinder block, and place in a vise equipped with soft jaws.
Remove six capscrews and lockwashers from engine flywheel housing. Drive out the two engine block dowels, remove fly wheel housing.
8. Remove fuel pump, starter, oil pressure regulator valve assembly, distributor, generator, oil gauge, coil, and all "freeze plugs" in block. (NOTE: Removal of the ''freeze plugs" or core hole plugs is only necessary when it is determined that the condition of the water passages in the block warrant a thorough cleaning, or the plugs appear to be leaking.) Clean inside and outside of block with a solvent cleaner or stearn. Install core plugs using SE-l 725 Adapter and SE-l58l-lB Handle.

3. Remove three screws from back cover plate. Remove plate and gasket from pump body (Fig. 33).
Water Pump Removal and Overhaul

The water pump is of the centrifugal pack less type (Fig. 31). It is bolted to the front end of the engine and is driven by the fan pulley. It requires no external adjustment. The bear ing is of the sealed lubricated type and does not require added lubrication at any time. The water pump is driven by a V -belt on the fan pulley. The pump, by means of centrifugal force developed by the impeller rotation, draws water up from the lower part of the radiator into the water passages in the cylinder block and cylinder head. The water circulates through the cylinder block and then out through the thermostat housing into the radiator upper tank.
Fig. 33
4. Remove snap ring from front of water pump shaft bearing (Fig. 34). Support the water pump on an arbor press and push shaft and bearing out, as one assembly (Fig. 35).
L22111
Fig. 31 - Sectional view of water pump.
Water Pump Disassembly

1. Remove four capscrews and lockwashers holding fan to hub. Remove fan blade as sembly from hub. 2. Remove four mounting capscrews from water pump (Fig. 32). Remove water pump from front end of cylinder head.
Fig. 311
......- - Press ram
Impeller
,.....: - - - - - Adapter
A-21905
Fi g. 32
F i9' 35

5. Place shaft assembly in press and press fan hub from shaft (Fig. 36). Donotattempt
to remove bearing or slinger, as they are factory installed on the shaft in the proper location.
ENGINES Silver Diamond Section A 13

If
4. Inspect pump shaft bearing for wear.

worn, replace bearing.
5. Examine shaft for wear and

needed.
replace if
6. Remove seal from housing through back

side of pump. Use a drift, and carefully drive seal from the pump body.
Water Pump Assembly

1. Press fan hub on shaft with the smaller diameter of the hub to the front (Fig. 37).
Water Pump Cleaning and Inspection

2. Install shaft in housing from front end by
Before reassembling water pump, the fol lowing should be checked:
1. Clean all parts by steam or cleaning sol vent.
pressing shaft, bearing, slinger, and fan hub in as one unit (Fig. 38).
3. Install snap (Fig. 39).
in place behind fan' hub
2. Examine seal for wear or damage and re place parts as necessary. Use special tool when installing seal. Use a new seal when rebuilding the pump since the old seal may have been damaged upon removal. 3. Examine pump impeller seat seal surface, if face of surface is scored, it must be re surfaced or replaced to prevent leakage.
4. Mount assembly in press. Press impeller on rear end of shaft. Place a straight edge across the back of the water pump housing and check the clearance between the straight edge and impeller. There should be about .025 11 clearance (Fig. 40).
Press ram
Fan hub - ....._r:':1
Bearing - - - J l....:;
~---hou8ing
Pump
Fig, 36
A-21947
Small hub end Large bub end
.........
Fig. 38
Fan hub
Water pump shaft - .......
bearing
14-21492
Fi g. 37
PRtNTED IN UNITED STATES OF" AMERICA
Fig. 39
Fi.g.
~o
Fig.
~2
5. Install cover plate with new gasket, and mount fan blades.
2. If vacuum is needed to operate any unit within the truck, a threaded inlet is pro vided in the manifold for such purposes.
Intake and Exhaust Manifolds

When disassembling and assembling the manifolds, the following procedures are used: 1. After removing the eight capscrews from head and three bolts from exhaust flange, remove both intake and exhaust manifolds as a unit (Fig. 41). NOTE: Let manifolds cool before starting above operations. 2. To separate the two manifolds, remove the two outside capscrews and two inside nuts from the center of manifolds (Fig. 42). 3. The intake and exhaust manifolds are each of one piece construction, requiring no disassembly after separation.
Exhaust Manifold
1. The exhaust manifold consists of four out lets. The two end outlets remove burned gases from the No. 1 and No.6 cylinders, while the two center outlets remove burned gases from Nos. 2, 3, 4 and 5 cylinders. 2. Located in the exhaust manifold, in the center, is the manifold heat control unit (Fig. 43).
Exhaust pipe flange --II"; Heat control valve
Fig.
~3
Intake Manifold
1. The intake manifold consists of three out lets, each supplying fuel to two cylinders. Two studs are located on the top for car buretor mounting.
3. The purpose of the heat control unit is to keep the intake manifold warm enough to vaporize the fuel mixture as completely as possible. The heat control is automatic in operation, being controlled by a coiled thermostatic spring. A counterweight, under spring tension, is mounted on the heat control valve shaft and this counter weight operates with the spring to close and operate the heat control valve.

4. Should the valve hold too much heat, the engine is likely to detonate or lping!1 when engine is accelerated. If valve opens too early, not enough heat is retained in the manifold, resulting in a slow warm-up. If the thermostatic spring becomes discon nected, the whole heat control system will be upset. 5. Should the shaft of the heat control become stuck, tapping it with a hammer and work ing the valve back and forth by hand usually frees it. An application of penetrating oil will help the process of freeing a sticking heat valve.
Gaskets _ _--litO"" Oil pump base - - - - -.....t!";'

A-2J563
Manifold Inspection
Inspect intake and exhaust manifolds visu ally for cracks or breakage. Place manifolds on surface plate and check for warpage. If cracked or broken, replace or weld. If slightly warped, true-up on surface grinder but replace if warpage is extreme.
Fi g. q5
Manifold Assembly
Place new gasket between the intake and exhaust manifolds and install two capscrews and two nuts. Mount manifolds together loose ly before installing on engine. This will assure proper alignment of the units with each other and with the engine cylinder head.
Idler gear
A-2IS6"
Oil Pump Removal and Overhaul

After oil pump has been removed, the fol lowing steps are to be used for disassembly: 1. Remove cotter pin holding float to oil pump (Fig. 44). Remove float from pump. Remove two capscrews holding pump in block. Remove oil pump.
Fig. q6
Spiral gear
Fi g. q7
4. Support oil pump shaft to prevent bending shaft, and using a small punch, drive out spiral gear pin from oil pu:rnp spiral gear (Fig. 47). 5. Place two support plates under spiral gear in press, and press oil pu:rnp drive shaft out of pump spiral gear (Fig. 48). Remove Woodruff key.
Fig. qq
2. Remove four capscrews and lockwashers from oil pump cover plate. Then lift cover and gasket from oil pump body (Fig. 45). 3. Lift out oil pump idler gear from idler gear shaft (Fig. 46).
PRIN'rO IN UNITED STATES OF' "MERICA

Oil Pump Assembly
The following instructions are to be fol lowed for reassembly: 1. Install new Woodruff key on body end of drive shaft. 2. Place in press and press body gear on drive shaft. The end of the shaft can be from flush to .030 11 below the level of gear face. 3. Insert oil pump drive shaft and body gear into oil pump body. 4. Install new Woodruff key in spiral gear end of drive shaft and press on spiral drive gear. Make sure that spiral gear hub is down. Install new spiral gear pin in place. 5. Install idler gear on idler gear shaft. In stall gaskets, oil pump body cover. four capscrews. and lockwashers. 6. Check oil pump body gear end clearance by using a dial indicator (Fig. 50). If end clearance is less than .0025" add one gas ket that measures not more than .003f! in thickness. If end clearance is in excess of ,0055 11 remove one gasket of not more than ,003" in thickness. Body gear end clearance should measure between ,0025 11 and .0055", 7. Inse rt oil pump float in oil pump, line up cotter pin holes, install new cotter pin. and fasten securely.
Fig. ~8 - Use SE-I~99 Oil pump support plate or other suitable support when pressing shaft from gear.
Pump body
Body gear - -.....i..'\;!

A-21935
Fig.
~9
Dial indicator
6. Remove body gear and drive shaft from oil pump body (Fig. 49). 7. Press pump body gear from shaft and re move Woodruff key. 8. Wash all parts in a cleaning solvent.
Oil Pump Inspection

Check the fallowing parts carefully: 1. Check oil pump drive shaft for wear at points of contact with body. If shaft is worn or bent, it should be replaced. 2. The standard measurement of oil pump shaft is .4885"-.4890". The shaft should be concentric and straight through its en tire length within .004 11 indicator reading. 3. Check oil pump body for warpage, damage. and wear. Replace if body is warped or cracked, or if shaft bore is worn so that clearance between shaft and bore is in ex cess of ,005!!, The oil pump body shaft bore measures .490 11 , 4. Inspect oil pump gears, and replace if wear is perceptible.
~B....-- Spiral gear

114---
Drive shaft
Oil pump - - - - - \ I....

body
A-2J565
Fig. 50 - Checking end clearance of pump and body gear.
shaft

DISASSEMBLY, CLEANING, INSPECTION,
REPAIR, AND ASSEMBLY OF
SUBASSEMBLIES
Replacing Camshaft Bushings

1. If camshaft bearing replacement is neces sary' remove and install new bushings with special camshaft bearing installation tool (Fig. 52). No reaming is required.
Cleaning the Cylinder Block

1.
Remove all old gasketmaterialirom block. Clean both inside and outside of block with steam or cleaning solvent. Remove all dirty oil, sludge, scale, and carbon from cylinder block. Check core plugs for in dication of leakage. Remove and replace plugs that show signs of leaking, or rust ing through. Use installing tool for core plug replacement (Fig. 51).
Bushing arbors
Camshaft bushings
A-22r49
Fig, 52 -SE-172Q Camshaft bushing installation. Showing tool in position.
Connecting-Rod and Piston

1.
Remove piston-pin retainers from each pis ton, and remove pis ton rings from pis ton ring grooves. heat using from After from
Fig. 51 - Installing core plug using SE-1725 Install ing tool with SE-1581-B handle.
2. Heat piston in boiling water or piston er. Place piston in piston vise, and pin-driving tool, drive pis ton pin piston and connecting rod (Fig. 53). piston pin is removed, lift piston connecting rod.
Cylinder Block Inspection

1. Inspect cylinder walls for cracks.
Weld the cracks or replace block if necessary.
2. Check top surface for trueness with a

straight-edge. Test by attempting to in sert a .012" feeler gauge ribbon between the straight-edge and the cylinder block. If this is possible, either surface or re place the cylinder block. 3. Inspect camshaft bearings for damaged or scored condition, and inspect for wear. Replace if damaged or if worn beyond clearance limit of .0 061!.
~
.,
\~
.. '.".'.'..'.
"
4. Measure
cylinder walls with an inside reading micrometer to determine taper, out-of-round, or worn condition. The measurements must be made not only at top of the cylinder bore, just below ring groove, but at several places around the inside circumference of the bore. Bore should be checked at the bottom, below ring wear surface, to determine the amount of taper. Rebore if worn beyond .008" clearance.
A22205
Fig, 53 - Use suitable piston vise to hold pis ton and drive piston pin out using SE-1263. Use soft (bronze or brass) hammer when driving to prevent damage to tools..
ENGINES Silver DiaInond Section A Page 18 3.

--~
Wash allparts ina cleaning solvent. CAU TION: Do not use a caustic solution for alUnlinUnl pistons. Clean the carbon froIn pis ton ring grooves with a broken ring or ring groove cleaner. Inspect connecting rods, caps, and bearing shells. All connecting-rod bearings and piston-pin bushings should be replaced at every Inajor overhaul. Test rods for align Inent. Rods only slightly mis -aligned can be straightened with proper equipment. Badly twisted or bent connecting rods must be replaced.
Press ram Adapter
4.
5. Inspect pistons for cracks, breakage, or scores. Check piston ring grooves and ring lands for wear, us ing a new pis ton ring and feeler gauge. If clearance be tween ring and ring land exceeds .005 11 , (total clearance) replace piston (see spec ifications for data covering piston fit in cylinder block). 6. Inspect piston pins for wear, and if wear is perceptible, replace pins. Replace pis ton pins which show signs of corrosion or etching. 7. With properly fitting adapter, press old piston-pin bushing from connecting rod (Fig. 54). Place new piston-pin bushing in position, align oil hole in bushing with oil hole in connecting rod, install bushing with a.0055" to .0035" press fit (Fig. 55). Bur nish bushing into place in the connecting rod (Fig. 56). 8. With reamer, ream piston-pin bosses in pis ton to provide a tight fit of froIn .0000" to .000211 with piston pin. NOTE: When fitting piston pins, the pins should be at room temperature (70 0 F.) and the pistons should be heated to approximately 200 0 F. in boiling water or piston heater. The pin should be a "palm-push" fit under these conditions.
Fig. 55 - Installing new bushing in rod.
Burnishing bar
Fig. 56 - Use SE-879 Burnishing tool. Connecting-Rod and Piston Assembly

1. With piston heated to approximately 200 0
F., support connecting rod in vis e, push piston pin into piston bosses while piston is hot (Fig. 57). When assembling piston on rod, the slot in the piston skirt must be toward the camshaft side of the engine, which is the nUnlbered side of the connect ing rod. Install piston-pin retainer in pis ton at each end of pin, making sure that
Press ram ----II"" Adapter - - - - - - I I..,
i,..'.". .,. . . .
.
':~
Fig. 5~ -Press bushing from rod using SE-I036-~ Bushing adapter and SE-I033 support plate.
Fig. 57

retainers sea.t fully and with tension in grooves. Test connecting-rod and piston assembly on a connecting-rod aliner, and correct any misalignment. 2. Place piston and connecting rod in vise. Test each piston ring for proper gap by placing in cylinder and rneasuring gap with feeler gauge. Gap should be .016" to .026" (Fig. 58).
3, Check crankshaft and flywheel dowels for damage and fit, and replace if worn or damaged, 4. Examine crankshaft timing gear teeth, and replace gear if teeth are worn or damaged. 5. Install Woodruff key in groove in crank shaft, Heat crankshaft gear in boiling water or piston heater. This will expand the gear enough to let it be tapped on the crankshaft without the danger of darnaging the gear. Use gear driver to insure align rnent when starting gear (Fig. 60).
Fig. 58 - Checking ring gap.

3. When installing piston rings in piston grooves, be careful not to distort rings. If possible use a suitable piston-ring ex pander tool (Fig. 59). Also check new piston rings in piston ring grooves for clearance between ring and ring lands. The correct ring clearance is shown in specifications.
Soft hammer Fig, 50 - Installing crankshaft using SE-1715 Installing tool.
A-27887
timing
gear
Flywheel and Ring Gear Inspection

1. Clean flywheel and ring gear with a clean ing solvent, remove all traces of oil and grease. Inspect the flywheel ring gear. If any teeth are darnaged, or if ring gear is loose on flywheel, the ring gear must be replaced. Check the flywheel dowel holes and mount ing bolt holes for wear, also check for flywheel having been loose.
Z.
3.
Piston ring
expander
4. To replace flywheel ring gear, heat gear with torch, and remove from flywheel with a hammer and drift. Heat new ring gear with torch, heating evenly all the way around. While the ring gear is hot, ins tall gear on flywheel and allow it to cool. 5. Check pilot bearing in flywheel for wear or damage and replace if needed. 6. Install flywheel on crankshaft. Install six self-locking caps crews, drIve dowel pins through flywheel to crankshaft.
Fig. 59 -Installing piston ring using SE-IIq,9-8 piston ring installing tool. Crankshaft Cleaning and Inspection
1. Wash and clean crankshaft with cleaning solvent or stearn.
2, Inspect rnain bearing and connecting-rod journals for wear, If journals show wear, or out-of-round in exces.s of ,003" > the shaft should be either reground and under size bearings installed, or replaced. Use micrometers for checking.
PRINTED IN UNITED
~n
Camshaft Cleaning and Inspection

1. Rernove nut frorn front of carnshaft gear. Attach gear puller, and remove carns haft gear frorn camshaft, and rernove Can:l shaft thrust flange. Remove Woodruff key.
... TES
OF AMERICA

5. Inspect crankshaft vibration damper for evidence of rubber corning loose from steel plates (SD-240 engines only) and in spect for wear. Replace damper if either condition is encountered. Do not sub merge vibration damper assembly in hot cleaning solvents. 6. Inspect crankshaft fan drive pulley for wear in hub bore. If inner diameter of bore is worn, scored, or Woodruff key way damaged, replace pulley. 7. Inspect engine gear case cover, and re place if cracked or broken. Remove old cover seal (Fig. 62) and with special driver install new seal (Fig. 63).
2. Wash parts in cleaning solvent, brushing to facilitate removal of all sludge or car bon deposits. 3. Inspect camshaft journals wear or out-of-round. for signs of
4. Inspect oil pump drive gear in center of shaft. If teeth are worn or damaged, the camshaft must be replaced, as the gear is integral with shaft. 5. Inspect camshaft lobes. If wont, chipped, or scored, replace the camshaft. 6. Inspect camshaft gear, and replace if wear is evident or gear teeth are nicked or otherwise damaged. 7. To reassemble, install thrust flange over end of camshaft. Install Woodruff key in slot in shaft. Place camshaft gear in boil ing water or piston heater, and install over Woodruff key. Install camshaft nut and tighten to approximately 120 foot-pounds tension.
Cleaning and Inspecting Miscellaneous Parts

1. Cleaning miscellaneous engine parts in cludes brackets, oil pan, engine case cover, flywheel housing, and other parts that were removed during disassembly of en gine and were not covered by procedure. Wash in cleaning solvent or stearn clean preliminary to inspection.
2. Check all twelve valve lifter or push rods for straightness by rolling on flat surface. Replace any that are bent or have loose ends (Fig. 61). Fig. 62
A-219DD
Hammer----:,.~liI~~/
F j g. 61
-----
Flat surface
A.21892
3. Inspect oil pan for cracks or deep bends, and straighten or weld. 4. Inspect oil pan drain plug and drain plug boss for fit and thread wear. If plug is loose or threads are damaged, replace plug. If threads in oil pan boss are worn or damaged, repair threads or replace oil pan.
Fig. 63 - Use SE-1718 Seal Installing tool with the SE-1581-B Handle.
8. Check each of 12 engine valve tappets for irregular wear, chipping, cracking, or scores. Replace defective tappets.

9. Inspect engine flywheel housing for cracks or breakage and replace if damaged. In spect flywheel housing to crankcase pilot dowel holes for wear. If wear is evident, drill or ream the holes and install over size dowels. Also inspect dowels for wear and replace if wear is evident. 10. Inspect all caps crews and nuts for thread wear or breakage, and replace as neces sary. Use new lockwashers when reaS sembling engine. 11. All gaskets and oil seals must be replaced at each overhaul or major repair.
more force is required to draw the cap and housing together.
DIFFERENCE BETWEEN DIAMETERS (A) AND (B) IS BEARING CRUSH (C)
ASSEMBLY OF ENGINE
When all parts have been cleaned. in spected, and repaired, and necessary replace ment parts have been procured, install engine cylinder block in engine overhaUl stand for re assembly.
DIAMETER (A) AT RIGHT ANGLES TO PARTING LINES GREATER THAN DIAMETER (B)
WITH BEARING CAP DRA WN UP TIGHT DIAMETERS (A) AND (8) ARE EQUAL
A. I 6009
Fig. 61t
Rods, caps, or blocks must not be filed, lapped, or in any other manner reworked in order to reduce clearance. While such prac tice will make a tighter fit at top and bottom, it will result in an out-of-round bore and bear ing shell distortion. New bearing shells will have to be installed eventually and that is when additional trouble starts. In general, a visual inspection of the part ing faces of the rod or caps under a magnify ing glass will provide sufficient proof of any attempt at reworking. Under the s, the parting line surface of standard parts will show the manufacturing cutte r tool marks and will not have a polished or extremely smooth appearance. On the other hand, reworked parts will have a polished surface and, if a file was used, will show the even pattern of the file teeth. Seriousness of this condition is in dir ect proportion to the amount of reworking. BEARING SPREAD. Main and connecting rod bearings are designed with the "spread ll (width across the open ends) slightly greater than the diameter of the crankcase bore or connecting-rod bore into which they are as sembled, (Fig. 65). For example, the width across the open ends of the Silver Diamond engine connecting-rod bearing, not in place, is approximately .025 ft more than when the bearing is in position in the rod. This condition causes the bearing to fit snugly in the rod bore and the bearing must be ftsnapped fl or lightly forced into its seat. Rough handling in shipment, storage, or normal results of use in an engine, may cause the bearing spread to be increased or decreased from the specified width. Bearing spread
Main Bearing and Connecting-Rod Bearing Installation

BEARING CRUSH. Undersize precision type bearing shells should be installed when, because of wear, bearing-to-crankshaft running clearances are to be reduced. Bearing caps must not be filed, lapped, or in any other man ner reworked. Premature bearing failure will result from attempts to reduce journal-to-bearing running clearance by reworking of either bearing caps, bearings, or both, because such reworking will alter the engineered fit of the bearing shells in their bores and destroy the specifically desired "crush". When installing precision-type connecting rod or main bearings, it is important that the bearing shells fit tightly in the rod or case bore. To accomplish this, the bearing manu facturer makes the diameter at right angles to the parting line slightly larger than the act'\al diameter of the bore into which they are assem bled. When the assembly is drawn up tight, the bearing is compressed, assuring a good contact between the bearing back and the bore. This increased diameter is referred to as bearing "crush" (Fig. 64). To obtain proper bearing assembly with the correct "crush", care must be taken when tightening the clamping bolts to make sure they are drawn down alternately and evenly, using a tension wrench and tightening as spec ified. As a result of excessive bearing crush due to reworking the caps, the rod or main bearing bore whll possibly become distorted, because
PRINTED IN UNITED STA.TES OF A.MERICA

moved. Place bearing shell halves in position in bore in cylinder block, making sure that bearing shells are fully seated, that oil holes in bearing shells line up with
SOFT MALLET (STRIKE LIGHTLY AND SQUARELY) O. D. OF BEARING WHEN INSTALLED IS THE SAME AS THE DIA. OF THE CRANKCASE OR CONN. ROD BORE
I"I1.1t--- JI A" ----------------~
SPREAD OF BEARING
BEFORE INSTALlA TrON Fig. 65
- - - - - - - - - - - - - A.16088
should, therefore, Le carefully measured and corrected as necessary before installation in an engine. Bearing .spread can be safely adjusted as follows, although care and judgment should be exercised in the process: 1. Excessive spread. If measurement of spread (Fig. 65) indicates that distance "AII is excessive (see chart for specifica tions), place bearing on a wood block (Fig. 66) and strike the side lightly and squarely with a soft mallet. Recheck measurement and, if necessary, continue until correct width (measurement HAil in chart) is ob tained. 2. Insufficient spread. If measurement of spread indicates insufficient spread, place bearing on wood block (Fig. 66) and strike the back of the bearing lightly and square ly with a soft mallet. Recheck measure ment and, if necessary, continue until cor rect width (measurement ItA" in chart) is obtained. Chart of Bearing Spread Dimensions. Silver Diamond Engine (Minimum) Connecting-Rod Bearing Main Bearing SOFT MALLET (STRIKE LIGHTLY AND SQUARELY)
DECREASING SPREAD
INCREASING SPREAD Fig. 66
A16095
"A"
2.500 11 2.942"
+ .025 11 + .025 11
1. INSTALL CRANKSHAFT AND BEARINGS. Clean all surfaces of crankshaft bearing journals and wipe clean the bearing bores in the cylinder block. Remove bearing cap self-locking capscrews and bearing cap. Wipe backs of cylinder block half of bear ings, making sure that dirt and oil are re
oil holes in cylinder block, and that lock ing tongs on bearings fit into recesses. Follow same procedure, place bearing shell cap halves in bearing caps. Place a film of engine oil on shell surfaces and lift crankshaft to align itself in the bear ings, and also provide lubrication. Place bearing caps and bearing lower halves over crankshaft journals. Be sure bear ing caps are properly installed with num bers to camshaft. 2. In order that an accurate measurement can be made to check all bearing clear ances, "plastigage" can be used. 3. Use the following instructions when using "plastigage ": (a) Remove oil from bearing cap insert and exposed half of crankshaft journal. (b) Place a piece of 'plastigage l1 the full width of the bearing inse rt.

(c) Reinstall the bearing cap. Tighten the self-locking capscrews to approxi mately 80 foot-pounds. (d) Remove the bearing cap. The flattened plastic material will be found adher ing to either the bearing shell or the crankshaft. (e) To determine the bearing clearance, compare the width of the flattened plastigage at its widest point with the graduations on the envelope (Fig. 67). The number within the graduation on the envelope indicates the clearance in thousandths of an inch. NOTE: Do not turn crankshaft during the above procedure.
block, trim ends of seal that project above cap surface level. Repeat the same oper ation with main bearing cap. Install wick ing on each side of rear main bearing cap (Fig. 69). Tighten all main bearing cap bolts to 80 foot-pounds.
Hammer--_.. Punch----JIIooII
Wicking - - - + (
Fig. 69 - Pack wicking securely using punch to work wicking into holes provided.
6. INSTALL FLYWHEEL HOUSING. Place flywheel housing in position over two fly wheel-housing-to-cylinder-block dowels, and tap into place with soft hammer. In stall six capscrews and lockwashers in flywheel housing. If either block or fly wheel housing is replaced, the flywheel housing will have to be aligned with a dial indicator. When correctly aligned, run-out of bore should not exceed .005". 7. INSTALL ENGINE FLYWHEEL. Place engine flywheel and ring gear into position. on dowels in crankshaft flange. Install six self-locking capscrews in flywheel and crankshaft flange, and tighten to a tension of approximately 60 foot-pounds, using a tension wrench. 8. INSTALL GEAR CASE COVER PLATE. Place plate and gasket at front end of en gine cylinder block. Install two capscrews and lockwashers. 9. INSTALL CA};,,1SHAFT AND GEAR. Coat camshaft with engine oil. Insert camshaft into front end of engine block, being care ful not to damage camshaft bearings. Be fore completely entering camshaft rotate shaft until marked teeth on crankshaft gear and camshaft gear index (Fig. 70). Install two capscrews and lockwashers in cam shaft thrust flange, working through large holes in camshaft gear. Rotate crankshaft and camshaft to establish that gears do not bind or interfere. Backlash must be from .000" to .007" (.0015" preferred). 10. INSTALL GEAR COVER CASE. gasket in position on case cover. Place Place
Fig. 67
4. If clearance is not within .001" to .004", either use undersize bearing, regrind shaft or replace shaft. Check crankshaft for end-play which is taken up by number three main bearing. End clearance should be from .0055" to .0135".
Fig. 68 - Installing upper oil seal in crank case using SE-1720 Rear ~ain Bearing Oil seal compressor.
5. Before installing rear main bearing cap (after all bearing clearances have been checked) install upper seal in block. Use special tool to press or roll seal in place (Fig. 68). After seal has been seated in
PRINTED IN UNITO ST4.TS OF A.MERICA.

connecting rod base, being sure that oil hole aligns with oil hole in connecting rod and that locking tangs of bearing shell fit into rece ss. Clean connecting-rod cap bearing bore and clean back of bearing. Place bearing shell lower half in connect ing rod cap, making sure that tang of bear-
Camshaft
r f .
~~
Fi g. 70
crankshaft oil slinger over end of crank shaft and install Woodruff key for fan drive pulley in crankshaft. Place gear case cover in position and install gear case cover aligning tool (Fig. 71). Install cap screws, new lockwashers, and nuts. Re move aligning tool.
Fig. 72
ing fits into recess in cap. (NOTE: See instructions under "Main Bearing and Con necting-Rod Bearing Installation".)
Timing gear
~Oli'l'r'--";;;=~
3. Coat bearing surfaces with oil. Pull con necting rod into position on crankshaft journal and install connecting-rod cap and bearing. NOTE: Bearing cap can only be installed on connecting rod one way, be cause of the construction of rod and cap. Install two self-locking capsc rews and tighten to 50 foot-pounds, using tension wrench.
A-22489
'...4.7\"
Fig. 71 - Aligning timing gear cover using SE 1717 Aligning tool.

11. INSTALL FAN DRIVE PULLEY AND Heat crankshaft VIBRA TION DAMPER. fan drive pulley and vibration damper as sembly in boiling water. When heated, quickly install assembly on crankshaft and install washer and fan drive pulley nut. Tighten nut with wrench of about 36 11 lever age. Vibration damper is used on the model SD-240 engine only.
4. To check connecting-rod bearing to crank shaft clearance, follow procedure given for flplastigage tl test. Specified connecting-rod bearing to crankshaft clearance is from .001" to .0035". Do not attempt to file con necting rod or bearing caps. 5. Follow the foregoing procedure for install ing remaining connecting rods and pistons. 6. INSTALL OIL PUMP. Place crankshaft and piston in position for firing on No. 1 piston. Insert oil, pump assembly into opening in cylinder block, rotate pump drive shaft so that tang in top of shaft is parallel to engine block. This position will assure the oil pump drive shaft being in proper position for distributor installation. Install and tighten two capscrews. Place one-piece oil pan gasket in place and install 25 capscrews around oil pan flange. 7. INSTALL CL UTCH. Install clutch driven disc against flywheel so that the long por tion of the hub is toward the rear. Place clutch in position on flywheel over clutch driven disc. Locate clutch so that arrow
Installing Connecting Rods and Pistons

1. Install one connecting-rod and piston as sembly down through top of cylinder block having slot in piston towards camshaft side of engine. Pistons are also marked with an arrow indicating front of engine. Use a piston ring compressor sleeve to com press piston rings and thus avoid possible ring damage (Fig. 72). 2. Wipe base of connecting rod free of oil and dirt. Place bearing shell upper half in

on flange of clutch backing plate or cone is as near as possible to the letter flL" on the flywheel, and install two or three mounting capscrews and lockwashers loosely. In sert a clutch aligning arbor, if available, or a transtnission main drive gear shaft, through clutch driven disc hub spline and into clutch pilot bearings. Hold clutch driven disc in position while completing installation of six mounting capscrews and lockwashers in flange of clutch backing plate or cover. Tighten all six capscrews securely. Remove three retaining cap screws and flat washers which were in stalled to hold clutch compressed. NOTE: Clutch will not operate properly unless these retaining capscrews are removed. 8. INSTALL VALVE TAPPETS. Coat each of 12 valve tappets with heavy engine oil and drop each, flat side down, through re cess in side of cylinder block into sockets in block (Fig. 73).
A .21938
Fig.
7~
3. ADJUSTING VALVES. To adjust valve stetn to valve rocker arm clearance cor rectly, each cylinder tnust be on top-dead center on its cotnpression stroke at the time of adjustment of valves for that cyl inder. To detertnine the correct position, turn the engine crankshaft until No. I piston is at top-dead-center on compression stroke and the ignition titning dot on the flywheel is in line with the pointer on the flywheel housing (Fig. 75). Adjust clear ance on each valve of No. I cylinder to .018" to .020" by using a feeler g'!luge be tween valve stem and valve rocker arrn and turn rocker-arm adjusting screw out of rocker arm until clearance is obtained. Tighten adjusting screw lock nut and re check clearance. (NOTE: Valve clearance should be rechecked with engine at normal operating tetnperature.)
Fig. 73
9. INSTALL VALVE LIFTER ROD COVER.

Install new gasket over opening at left hand side of engine block. Install valve lifter rod covers and slotted screws.
Install Cylinder Head

1. INSTALL HEAD. Place gasketon cylinder block and align bolt holes. Place cylinder head on crankcase, being careful not to damage of shift gasket position. Loosely install all cylinder-head bolts and flat washers, otnitting bolts in holes for rock er-artn assetnbly.
Fi g. 75
4. Turn crankshi:tft one-third revolution and adjust clearance on No.5 valves. Working in firing order sequence, continue to set valves of each of the remaining cylinders, turning crankshaft one-third turn after each valve adjustment. 5. INSTALL INTAKE AND EXHAUST MAN IFOLDS. To facilitate installing the mani folds, after manifold gaskets and pilot rings are installed, start capscrews at each end of intake manifold. This will pertnit the
2. INSTALL VALVE ROCKER-ARM ASSEM BLY. Insert 12 valve lifter rods in cylin der head, make sure they enter the valve tappet. Lift the valve rocker-arm assem bly into position on cylinder head with the drilled oil bracket placed third from front. Make sure number 2, 4, and 6 bracket sleeve dowels are in place (Fig. 74). In stall the retnainder of cylinder-head bolts and tighten alternately and evenly in se quence to 90 foot-pounds.
manifold to slide straight up between the

engine head and capscrews and flat wash
ers. When manifold is lined up with pilot
rings and gasket, tilt bottom of manifold
toward engine block. This will force man
ifold out at top enough to bind against the
two capscrews and hold manifold in posi
tion until the front and rear capscrews can
be installed (Fig. 76).
Cartridge
\
Return channel
Fig. 76
6. INSTALL WATER PUMP. Place water
pump gasket in position, at water pump
opening in front of cylinder head. Install
water pump and fan and install four cap
screws and lockwashers in pump and cyl
inder block.
7. INSTALL OIL FILTER. Place oil filter and new gasket in place on cylinder block. Install four capscrews and lockwashers in oil filter base. (NOTE: Be sure filter assembly is thoroughly cleaned and a new cartridge is installed before replacement on engine.) Tighten center tube nut using wrench SE-1728.
8. INSTALL ACCESSORIES. Install carbu retor, generator, distributor and connect ing wires, starter, fuel pump, ignition coil, oil gauge, and thermostat. 9. FILL ENGINE WITH OIL. After making certain that oil drain plug is securely in stalled, fill crankcase with oil. After en gine has been installed and placed in oper ation, again recheck oil level and if neces saryadd sufficient oil to bring level up to full mark on gauge. 10. INSTALL CYLINDER-HEAD COVER. If engine is not to be installed at this time, install new cylinder-head cover gasket and install cylinder-head cover. Install three flat copper washers and three capscrews on cover.
Gasket
Relief valve
Gasket
8-4744
Fig. 77 - Details of Deluxe Oil Filter.
ENGINES
Super Blue Dianrrond Section B Page 1
SUPER BLUE DIAMOND ENGINE
c:
(t\
PRINTED IN UNITEO STATES 0'" "'''''ERICA
ENGINES Super Blue Diamond Section B Page 2
L-U\lE MOTOR TRUCK SERVICE MANUAL

The crankshaft is a drop forging of heat treated steel. It is counterweighted, bal anced both statically and dynamically, and ground to close limits. The shaft is mounted in four precision-type replaceable shell bearings, the number four (rear) bearing taking up the thrust. 9. The pistons are made of an aluminum alloy, are cam ground. and are fitted with three compression rings and one oil control ring. The full-floating type piston pins are held in plac e in the pis tons, at the ends of the pins. by snap rings. IO. The camshaft is machined from a solid drop forging and mounted in four special replaceable bearings. 11. The flywheel is bolted and doweled to the crankshaft flange. The timing mark is located on the front crankshaft pulley. 8.
DESCRIPTION
General
The Model BD, Super Blue Diamond engine is a 4-cycle, 6-cylinder-in-line,. overhead valve-type engine (Fig. 1). The engine serial number is s tamped on a pad at the front on the left side of the crankcase just below the cylin der head. The block has dry-type replaceable liners for the cylinders. The detachable cyl inder head contains all valves, valve guides. and springs. The cylinders are numbered from front (fan and timing gear end) to rear. Engine crankshaft rotation is clockwise as viewed from the front end of the vehicle. The intake and exha us t manifolds, carbur etor, starter, and generator are located on the right side of the engine. The dis tributor, fuel punlP, and oil filter are located on the left side. The oil filler inlet is located in the valve cover on the top of engine. The bayonet type oil level gauge is located on the left side. The water pump is located at the front of engine.
ENGINE REMOVAL
The engine. with transmission removed, can be lifted from chassis without disturbing the fender and grille assembly, by using a suit able chain sling and a floor crane. Disconnect the following electrical cir cuits, hose connections, and various units as outlined (Fig. 2 and Fig. 3);
Construction
1. The generator, fan, and water pump are driven by a V -type belt from a driven pul ley mounted on the front end of the crank shaft. The distributor, mounted at the left side of the engine, is driven by the cam shaft through the oil pump.
2. The exhaus t and intake manifolds are bolted to each other and to the right side of the engine head. The intake manifold and the exhaust manifold are each cast in one piece. 3. A vibration damper is provided at the front end of the crankshaft. 4. The cylinder block and crankcase are cast in one piece, and carry the crankshaft main bearings. Water circulation passages completely surround the cylinders in the crankcase and also provide coolant to the cylinder head.
Fi g. 2
5. Oil is supplied under pressure by the oil pump to the engine lubrication system. Oil spray from the revolving crankshaft is distributed to the cylinder walls, pistons, and other moving parts inside the engine. 6. Exhaust valve seats are of alloy and are pressed into place. These valve seats lengthen the period between valve recon ditioning operations. Valves and valve seats are cooled by continuous circulation of water through the cylinder head. 7. The detachable cylinder head is bolted to the c rankcas e, and a gas tight and wate rtight seal is maintained by means of a gasket.
Fig. 3

1. Drain engine oil pan. Drain all coolant from engine cooling system by opening the drain cock on side of engine as well as the radiator drain cock. Remove radiator fil ler cap when draining cooling system. Disconnect upper and lower radiator hose connections. Disconnect engine air clean er and remove air cleaner. Disconnect vacuum line at manifold. Disconnect engine circuit Wlrlng. This includes coil wire, starter cable, engine ground strap and instrument sender unit wires. Disconnect fuel line at fuel pump. Discon nect throttle control linkage and remove choke at carburetor. Disconnect clutch linkage at bell housing. Remove engine rear mounting bolts from both sides of engine support pads. Remove engine front mounting bolts from support bracket; these are the bolts at the front crossmember. Remove radiator mounting bolts and lift out radiator support and core assembly.
,......t - - -
ENGINE DISASSEMBLY
Install the engine ina suitable rotating en gine overhaul stand. NOTE: Many of the dis assembly operations can be performed with the engine in the chassis. However, the following dis ass embly outline is performed with the en gine removed from the chassis to clearly illus trate each of the units. Except where indicated, no attempt has been made to prescribe a par ticular sequence for removing the various units, since some can be readily removed with the engine in the chassis. The extent of the serv ice required on a particular unit will govern the necessity for its removal.
2.
3.
4.

The following steps are to be followed when removing the rocker-arm cover and rocker arm assembly. (Carburetor and air cleaner previously removed.):
5. 6.
1. Remove three nuts from rocker-arm cover.

2. Remove air cleaner line and remove cover. Remove bolts from shaft brackets (Fig. 5.) NOTE: Left front head bolt supplies oil to rocker arms.
7.
8.
Drilled bolt
9.
Disconnect engine exhaust pipe at mani fold.
10. Attach engine sling to front and rear right side cylinder head bolts and remove en gine (Fig. 4).
Oil hole--.....
.A-22220
Fig. 5
3. Remove rocker-arm assembly as a unit.
Rocker-Arm and Valve Mechanism Disassambly

1.
The rocker-arm assembly is composed of front and rear shafts joined at the center, on which are mounted twelve rocker arms and six tension springs. The shafts are mounted in seven brackets, and are pre vented from turning at the two end brack ets, by slots in the shaft into which the cylinder-head bolts fit (Fig. 6).
Fig. ~ - Removing engine from chassis. Chain sl ing attached to front and rear right sidecyl inder head bolts.
ENGINES Super Blue Dia:mond Section B Page 4

Exhaust valve rocker arm Intake valve rocker arm
Front rocker arm shaft
Oil connection bracket
A-22207
Fig. 6 - Details of rocker-arm assembly.

2. 3. Separate the shafts and slide rocker ar:ms, springs, and brackets fro:m shafts. Clean all parts in a solvent cleaning fluid, being careful to clean all accu:mulated sludge and carbon deposits fro:m oil holes and slots. surface of rocker ar:m, and resurface if wear is perceptible. Do not re:move :more than .010" of :material when resurfacing rocker-ar:m pads. 3. Inspect tension springs for breakage or loss of tension. Replace defective springs. Re:move valve lifter rods fro:m engine.

....- - Press ram
Carefully inspect all parts for defects and wear.
1. Inspect rocker-ar:m shaft expansion plugs. Check on a surface plate for signs of bend ing, check for wear fro:m rocker ar:ms. If a shaft is bent or shows perceptible wear, it :must be replaced.
2. Inspect rocker-ar:m adjusting screws for wear at contac t surface and for thread wear. Replace worn screws. Check rocker-ar:m bushings. Inspect valve ste:m contact pad
"''--- Bushing installing tool
'.......- - Press ram
..,.f------ Bushing removing tool
Fig. 8 - Showing method of install ing new rocker arm bush i ng.
Rocker arm
- - Press plate
. . . .i
~.
~--- Burnishing
tool
Fig. 7 - Use SE-1036-1 Bushing Removing Tool when removing the rocker arm bushing. Support the rocker arm on the SE-1033 support block. Select a hole in the support block to properly support the rocker arm at the same time permit the bushing to clear the support block when being removed. Use the support block when in stalling and burnishing the new bushing.
Fig. 9 - Burnishing rocker arm bushing. Use SE 931 Burnishing Tool.

Re-bushing Rocker Arms
With properly fitting adapter or special tool equipment provided (Figs. 7, 8 and 9), press old rocker-arm bushing from rockerarm. Place new rocker-arm bushing in position. Align oil hole in bushing with oil hole in rock er arm, which is located 30 0 from top of rock er arm toward rocker-arm adjusting nut. Using installing tool, press new bushing into rocker arm. Burnish bushing into place in the rocker arm, then ream rocker-arm bushing to provide .0015" to .004" clearance. Ream dimension is .7505" - .7520".
Inspection of Valve Guides, Valve Springs and Valves

1. Clean valve guides witha suitable cleaning
tool. Check each valve guide with a "Go and No-Go" gauge, if available; otherwise, use a new valve to check fit. If "No-Go" portion of gauge enters, the guide mus t be replaced. Recommended valve stem to valve guide clearance is from. 002" to. 004" for exhaust valves, and from .0015" to .0035" for intake valves. CleaTance in ex cess of .006" for intake valves or .008" for exhaust valves, require guide replacement. Ream guides to .3435 11-.3455" after assem bly in cylinder head. 2. Test valve springs with damper in posi tion. Test tension of each valve spring at valve open length with a valve-spring test er (F',g. 10). Check valve springs at 1-43/6411 length, and replace if pressure is less than III Ibs.
Cylinder Head and Valves

The following instructions are to be fol lowed when reconditioning cylinder head and valves. Remove push rods, remove cylinder head bolts and lift off cylinder head and gasket. Place cylinder head on bench. 1. Compress valve spring with a valve com pressor and remove valve spring retainer locks. Remove retainer. Remove valve spring and damper and separate valve spring damper from valve spring. Re move all valve springs as outlined, and remOve valve spring damper from each spring. Invert cylinder head. Remove all valves from their valve guides and from the head, keeping each valve ina suitable rack which will assure replacement of the valves in their original location.
2.
Scale (inches)--~
~;..,-----
Valve spring'
3. Scrape all carbon from cylinder-head com bustion chamber, and clean any gasket material from surface of head. Clean the head using steam cleaning or other suit able cleaning equipment. 4. Cleanall carbon deposits from valve heads and valve stems with wire brush. Wash all valve springs and retainers in cleaning solvent.
~---b-'----
Scale (pounds)
A21lt90

1. Inspect cylinder head visually for signs
of cracks or sand holes and if found de fective. weld or t-eplace head. 2. Inspect exhaust valve seat rings for loose ness and inspect for excessive width of valve seat surface. If insert rings are loos e, replace. If a seat has been previ ously ground to such extent that it cannot be narrowed from top to bring to proper position near center of valve face, the ring must be replaced.
P~INTEO
Fig. 10 - Test valve springs in spring testing tool.
SE-1565 Valve
3. Inspect each valve for warpage. for se verely burned condition, and for exces sive grinding on the valve head. Inspect valve stem for scuff marks or perceptible wear. Inspect valve stem end for wear at contact surface with valve rocker arm. If valve is warped, excessively burned, or has been previously ground to extent that valve head is thin at edge, replace valve; otherwise, valve can be reconditioned and reins taIled.
IN UNITED STATES OF AMERICA

prevent burning of the seat and warping of the valve head. The location of the valve seat on the valve face and its width controls the amount of valve head that protrudes into the combustion cham ber. It is obvious that the greater the exposure within the combustion chamber, the higher the valve temperature; or in other words, the more heat it will collect. High valve tempe rature and poor heat dissipation also produce excessive valve stern temperatures and hasten the ac;cu mulation of carbon on the stern, causing them to stick in the guides.
Repair of Cylinder Head

1.
If cylinder head has to be resurfaced, re move only enough material to true-up surface. If any valve guide shows excessive clear ance or out-of-round condition, press guide from head with special removing tool. In stall new guide, and press into head until approximately 1-1/16" remains above the top surface of the head. Checkvalve guides after installation to .v02" to .004" for ex haust and .0015 11 to .0035" on intake with "Go and No-Go" gauge. Ream valve guides to .3435"-.3455" after assembly in cylinder head.
2.
Valve Seat Widths

In general, the width of exhaust seat should range between the average and maximum spec ifications and the intake seats between the
3. If inspection indicates necessity, replace valve seat.
4. Grind valve seats in cylinder head to 45 0 on both exhaust and intake.

One of the principal difficulties experi enced in reconditioning valves is obtaining nearly identical angles on the valve seat and valve face. The importance of these angles in the grinding operation cannot be overempha sized, because it is impossible to produce a flat or square seat by lapping. The grinding stones on both the valve refacing machine and valve seat grinder should be dress ed before starting a reconditioning job. You will be unable to determine how closely the angle of the seat will match the valve face until the valve and seat have been ground and a check made with a very light tint of Prussian blue. If a full seat-width contact around the entire circle of seated valve is not shown, the angles do not match. It will then be necessary to redress the valve seat grinding stones, changing the angle sufficiently to correct the error. The correction should be made on the valve seat, and not on the valve. No more material should be removed from the valve face than is necessary to true it up and remove the burned or pitted portion. New valves should not be refaced, but should be checked for trueness. When a satisfactory match of valve seat and valve face angles has been ob tained, the adjustment of both the valve refacer and the seat grinder should be locked in posi tion, in order to eliminate this trial-by-error method on additional valves having the same angle.
Low limit . . . . . . . { High limit . . . . . . . Preferred . . . . . . . Minimum seat
3/16" 5/64" V16"
Low limit . . . . . . . High limit . . . . . . . { Preferred . . . . . . . Maximum seat
5/64"
V64"
3/32"
Valve Seats
The primary purpose of a valve seat is to seal the combustion chamber against pressure losses and to provide a path to dissipate the heat accumulated in the valve head so as to
A-22611
Fig, II - Valve seat widths.

mlnlmum and average specifications. The intake seats may be narrower than the exhaust because they are usually larger in diameter, thus providing a total seat area approximately equal to smaller exhaust valve with the wider seat. Also the less severe heat conditions do not require as large a seat area for heat dis sipation purposes. Fig. 11 illustrates recom mended valve seats to be obtained. There are also objections to an excessive ly wide seat, a few of which are as follows:
5. Inspect each valve coated with blue for seat position. The seat should be at the approximate center of valve face, 7/64 11 5/64 11 wide for exhaust, and 5/64 11 -7/64" wide for intake.
Valve Assembly
1. Wipe valve faces and valve seats with a
cleaning solvent to remove all dirt or for eign material. Coat valve stems and valve faces with oil, and install valves in same seats to which they were checked. 2. Install valve springs with dampers. Com press valve springs with a valve spring compressor, and install valve spring re tainers and retainer locks. Be sure that retainers and locks are correctly seated.
1. In city or light delivery service, a wide

seat collects carbon and particles of dirt that will produce variations or los s of compression, resulting in poor idle and possible a loss of general performance and economy. 2. A wide seat in severe service operating in the pres ence of dirt or an exces s of carbon will produce a badly pitted seat which may be just as detrimental to valve life as a too narrow seat. Under these conditions, a seat width to the Ininimum liInit would possibly be better; however, the source of trouble (which is the dirt and excessive carbon) should be eliIninated, Inaking it possible to retain the wider seat.
Engine Disassembly - Continued

When overhauling engine with head and pan reInoved, the following procedures are recom mended:
1. Remove fan drive pulley nut and washer

from end of crankshaft. Install puller and reInove crankshaft fan drive pulley and damper assembly froIn crankshaft. 2. Remove nuts and caps crews from engine gear case cover (Fig. 12), reInove gear case cover (Fig. 13). ReInove crankshaft oil slinger from end of shaft (Fig. 14). Re move side cover plate and reInove valve tappets (Fig. 15). ReInove nut from end of camshaft and remove caIns haft gear with puller (Fig. 16). NOTE: Camshaft Inay be reInoved without reInoving tiIning gear, by removing thrust plate retainer screws.
Valve Seat Inserts

Necessity for replacing valve seat inserts should be very rare; however, if a replace ment is made it is important that new inserts be peened securely in place, using either insert peening tool or a dull-pointed chisel, 1/4 11 wide, to peen cylinder head metal over outer edge of valve seat insert. Valve available. seat insert installing tools are
Valve seat inserts supplied for service are standard size and .030" oversize which perInits a tight fit in cylinder head.
Repair of Valves
1.
True-up the ends of valve steIn against face of grinder. ReInove only enough material to true the surface. Reface exhaust valves to 45 0 The valve face and valve seat angle mustbe identical.
2.
3. Reface intake valves to 45 0 with valve seat being the same. 4. Place valves in cylinder head. Place a thin coat of Prussian blue on each valve face, and tap valve lightly to its seat. NOTE: This is merely for test and proof of results of refacing and res eating oper a tions. A poor grinding job cannot be cor rected by valve lapping.
~ b r ,
,
Crankshaft
Fig. 12 - Removing timing gear case cover.
Fig. 16 - Pulling camshaft gear. Fig. 13 - Showing Cover removed. details of timing gears.
3. Remove capscrews from camshaft retainer thrustflange plate (Fig. 17). Remove cam shaft (Fig. 18). Remove capscrew holding the gear case cover plate to block; remove plate and gasket. Remove crankshaft tim ing gear, using a gear puller (Fig. 19). (NOTE: Lubricate puller screw to pre vent damage to screw threads.)
Fig. II~ - Removal of oil slinger. flange of slinger is bent outward.
Mote
that
Fig. 17 - Removing camshaft with gear removed. Camshaft may be removed with gear attached.
Fig. 15 - Tappets are removed to permit removal

of camshaft.
Fig. 18 - Removing camshaft.
ENGINES Super Blue DiaInond Section B Page 9
7,
8,
crankshaft; reInove flywheel with ring gear asseInbly. ReInove caps crews and lockwashers froIn engine flywheel housing. Drive out the two engine block dowels, reInove flywheel housin'g (Fig. 22). ReInove fuel PUITIP, starter, oil pressure regulator valve asseInbly, distributor, gen erator, oil gauge and coil.
Crankshaft timing gear

A-21936
Fig. 19 - Pull crankshaft gear, using SE-1715 Gear pul Jer. Lubricate threads of puJ ler to prevent damage to puller threads.
Turn engine in overhaul stand and proceed with disasseInbly as follows: 4. Each connecting rod is nUITIbered as to its position in the engine and these nUITIbers are located on the caInshaft side of the en gine (Fig. 20). ReInove self-locking cap screws froIn connecting-rod cap and re Inove cap. Push connecting-rod and piston asseInbly toward top of block, but first reInove ridge froIn top of cylinder wall, if any. Lift piston and connecting-rodasseIn bly froIn top of cylinder block, Replace cap on connecting rod. ReInove the re Inaining pis tons, following the saIne pro cedure.
Fig. 21
COJIDec:ting rod Learing
Piston pin bushing Self-locking bolt

Fig. 20
5. The crankshaft bearing caps are nUITIbered to identify their position and they InUS t be reinstalled in their respective positions. ReInove self-locking caps crews froIn each bearing cap. ReInove all crankshaft Inain bearing caps (Fig. 21). After all caps have been reInoved, lift crankshaft straight up and out of cylinder block, and place in a vise equipped with soft jaws.
A-221l4
Fig. 22

See sectional view of BD Engine water pUITIp (Fig. 23), The water pUITIp asseInbly is cOInposed of a body and cover plate which house a ball-bearing Inounted pUITIp shaft and iInpeller, The rear and front bearings are pressed onto the shaft and are separated by a spacer. A slinger is held in place by two half-lock rings. The shaft asseInbly with its two bearings is held in place in the housing by a retaining snap ring. The fan pulley is pressed onto the shaft (press fit .0007" to .0018 11 ) and held in place by a nut and plain washer.
6. With crankshaft securely claInped in vise, reInove the six self-locking caps crews holding flywheel to crankshaft. Tap fly wheel with a soft haInIner to loosen itfroIn
PFUNTEO IN UNITED STATES OF AMERICA

2, Examine seal parts for wear, corrosion, or damage, and replace with new parts as necessary. Examine the pump body seal seat surface. If face of surface is scored, it must be resurfaced to prevent leakage. Inspect pump shaft bearing for wear or corrosion. If worn or corroded, replace bearings, Examine shaft for wear at ends, or for damaged threads at front end.
Water Pump Repair

If water pump body seal seat is scored, pitted, or rough, it must be resurfaced. Use special water pump housing seat finishing tool and adapter.
Water Pump Assembly

Fig, 23
The impeller seal assembly consists of a seal spring, seal clamp ring, flexible seal, seal spring guide, and a seal carbon washer. The parts are held in place in the impeller by a snap ring. The impeller and seal assembly is press ed onto the pump shaft (pres s fit of .002" to .0035").
1.
Install rear bearing. spacer. and front bearing onto water pump shaft. Place slinger in position behind rear bearing. Place two half-moon lock rings in groove in shaft, and press shaft into bearing and spacer from rear until rear bearing rests firmly against slinger and ring locks,

(Complete illustrated procedure for water pump servicing is given in Shop Talk No. 14) 1. Remove six capscrews and lockwashers holding fan to pulley. Remove fan blade ass embly from pulley. Remove water pump from front end of cylinder head. Remove nut and flat washer holding pulley to water pump shaft. Remove pulley from water pump shaft with puller. Remove four capscrews from cover plate. Remove plate and gasket from pump body. Remove snap ring from front of the water pump shaft front bearing. Supporting water pump on arbor press, push shaft. and bear ing as an assembly out of impeller from the rear.
2. Place seal clamp ring, seal spring, seal spring guide, flexible seal and retainer, and carbon seal thrust washer into position in impeller. Hold them in position while ins talling snap ring in impeller groove. 3. Ins tall water pump shaft and bearing ass em bly into body and hold in place by inserting snap ring in groove in front of front bear ing. 4. Support water pump shaft at front end, pres s impeller and seal ass embly onto rear end of water pump shaft. Press im peller only flush with end of shaft. 5. Place new gasket in position on water pump body and install cover plate and four cap screws. 6. Place fan assembly in position on front of pulley, and install six capscrews and lock washers. Fill pump housing with wheel bearing grease. Use low pressure gun.
2.
3, 4,
5. Support the shaft and bearing assembly on an arbor press, fo;r:ce shaft out of bearing, spacer, and slinger, pressing shaft toward rear bearing. Be careful not to lose the two halfmoon lock from under the slinger. 6. Remove snap ring from groove in the front of impeller, and lift out the seal parts from the impeller.

When disassembling and assembling the manifolds, the following procedures are us ed: 1. After removing the eight capscrews from head and three bolts from exhaust flange, remove both intake and exhaust manifolds as a unit (Fig. 24). Remove three manifold pilot rings (Fig. 25). NOTE: Let mani folds cool before starting above operations; this will help to prevent manifold warpage.

1, Following disassembly, wash all except rubber parts in cleaning solvent.
cracked or broken, replace or weld. If slightly warped, true-up on surface grinder but replace if warpage is extreme.
Manifold Assembly
Place new gasket between the intake and exhaust manifolds and install two capscrews and two nuts. Mount manifolds together loos ely before installing on engine. This will assure proper alignment of the units with each other and with the engine cylinder head. NOTE: Do not eliminate the intake manifold aligning pilot rings.
Fig. 2q - Removing intake and exhaust manifold.
Oil Pump Overhaul

(Complete illustrated procedure for oil pump overhual is given in Shop Talk No. 28) Special tool equipment is available for oil pump overhaul under SE-1499. Use of these tools will speed up the job and assure accurate work.
11"'Y.:'1~--GUIDE
*+--KEY 'I..lI,J.~- SPIRAL GEAR
Fig. 25 - Pilot rings are used to hold the in take manifold in alignment and should always be reinstalled.
2. To separate the two manifolds, remove the two outside bolts and nuts and two inside bolts and nuts from the center of mani folds.
.:i!!E---i---
PIN
SHAFT
3. The intake and exhaust manifolds are each of one piece construction, requiring no disasseITlbly after separation.
i"Il----
BODY
Intake Manifold
1.
The intake manifold consists of three out lets, each supplying fuel to two cylinders. Two studs are located on the top for car buretor ITloun ting.
IDLER GEAR SHAFT
OIL
2. If vacuum is needed to operate any unit within the truck, a threaded inlet is pro vided in the manifold for such purposes.
FLOAT
Exhaust Manifold
The exhaust manifold consists of four out lets. The two end outlets remove burned gases froITl the No. I and No.6 cylinders, while the two center outlets remove burned gas es froITl Nos. 2, 3, 4 and 5 cylinders.
A.J09SI
Fig. 26 Oil Pump Disassembly

See sectional view of the model BD engine oil pump (Fig. 26),
Manifold Inspection
Inspect intake and exhaust manifolds visu ally for cracks or breakage. Place manifolds on surface plate and check for warpage. If
1. Remove cotter pin holding float to oilpump.

Using hole in spiral gear as guide, drill .1255" hole in shaft. Drive new spiral gear pin into place. Install a new guide on the end of the pump shaft. use guide installing tool. 3. Install idler gear on idler gear shaft. In stall gasket and oil pump body cover, and install four capsc.rews and lockwashers. Test oil pump body gear end play to cover by using a feeler gauge between oil pump spiral gear hub and oil pump body. End playmustbefroIn.0025 11 -.0055". Ifc1ear ance is in excess of .0055", remove one gasket from cover. If clearance is less than .0025", add one gasket between cover and body. Recheck end play after making any alterations. Insert oil pump into cyl inde r block so that s lot in top of s haft is at right angles to the side of the engin~ with the number one piston in firing order. 4. Connect oil pump outlet to pump and tighten coupling. Insert oil pump float in oil pump body, line up cotter pin holes, install new cotter pin, and fasten securely.
Remove float from pump. Loosen oil out let coupling and remove oil line from pump. 2. Remove four capscrews and lockwashers from oil pump body cover and lift cover and gaskets from oil pump body. 3, Lift out oil pump idler gear from idler gear shaft. After removing oil pump drive gear shaft guide from top of shaft, use small punch to drive out spiral gear pin from oil pump spiral gear. Using an adapter collar which fits underneath the spiral gear, and an adapter with a tang which will fit down into the slot of the oil pump drive shaft so as to apply pressure of press at bottom of slot, press oil pump drive shaft out of oil pump spiral gear. Remove Woodruff key from shaft. Remove oil pump body gear and oil pump drive shaft from oil pump body. 4, Press oil pump gear onto oil pump drive shaft far enough to reveal retainer ring. Remove ring from oil pump shaft. Press oil pump body gear from shaft and remove Woodruff key from shaft, Wash all parts in cleaning solvent.
Oil Pump Inspection

Check the following parts carefully: 1. Check the oil pump drive shaft for wear at points of contact with body. If wear is perceptible, the shaft must be replaced. Diameter of shaft is from .4985 to .4992 inches. 2. Check the oil pump body for warpage, dam age and wear. Replace if body is warped or cracked, or if shaft bore is worn so that clearance between shaft and bore is in excess oL005". Inspectall oil pump gears, and replace if wear is perceptible.

REPAIR AND ASSEMBLY OF
SUB-ASSEMBLIES
Remove all old gasket material from block, clean both inside and outside of block with stearn or cleaning solvent. Remove all dirty oil, sludge, scale, and carbon from cylinder block.

1. Inspect cylinder walls for cracks. Weld cracks or replace block, if necessary. 2. Check top surface for trueness with a straight-edge. Test by attempting to in sert a .012" feeler gauge ribbon between the straight-edge and the cylinder block. If this is possible, either surface grind or replace the cylinder block. 3. Inspect camshaft bearings for damaged or scored condition, and inspect for wear. Replace if damaged or if worn beyond clearance limit of .0035 11 , 4. Measure cylinder walls with an inside reading micrometer to determine taper, out-of-round or worn condition. The meas urements must be made not only at top of the cylinder bore, just below ring groove, but at several places around the inside circurn:ference of the bore. Bore should be checked at the bottom, below ring wear surface, to determine the amount of taper. Re-sleeve if worn beyond .008" clearance.
Oil Pump Assembly

1. Press body gear onto oil pump drive shaft after placing new Woodruff key in slot of shaft. Press gear onto shaft far enough to permit installation of retainer ring in groove in oil pump. Press oil pump body gear down against ring. 2. Insert oil pump drive shaft and body gear into oil pump body. Install new Woodruff key in slot at top end of shaft. Install oil pump spiral gear, with gear hub down, onto drive shaft. Press spiral gear down onto shaft until 1/32" clearance remains be tween gear hub and pump body when oil pump body gear is up against pump body;

Cylinder Sleeve Fits
The fit ofthe cylinder sleeve in the crank case should be 100 to 200 1bs. hand push fit or approxinaately.0005" to .001" loose fit. This fit can be obtained by honing the cylinder bore sufficiently in the crankcase until the cylinder sleeve can be pushed all the way in by hand. Before installation of cylinder sleeve. the crankcase bores should be cleaned of all car bon and foreign naatter. Installation of cylinder sleeves in the fore going naanner will preclude to a large extent the necessity of excessive honing when fitting pistons to the cylinder sleeves. NOTE: If cylinder water jacket shows an excessive anaount of linae deposits, the cooling systena cannot provide effective heat dissipa tion. Whenever the top of the sleeve flange goes below the top of the crankcase, a thin tag wire should be placed under the sleeve flange to raise it flush with the crankcase, or not to ex ceed .006" above the crankcase face. Cylinder wall surface finish is of utnaost inaportance in piston and piston ring life and in oil consunaption control. The best type surface is one having characteristics naidway between "snaooth" and "highly polished". The resulting surface of a boring or honing operation consists of nunaerous naicroscopic scratches or grooves which act as oil reservoirs or retainers of oil while the surface between the grooves provides a load-bearing surface. If the scratches are too deep and too close together, the surface is referred to as "rough" and will not provide adequate ring and piston ,c.orlta'ct area which results infast wear. Should the finish be highly polished or too "snaooth", the scratches or grooves are shallow and will have insufficient oil-retaining capacity to provide adequate lu brication for the adjacent contact or load bearing area and will result in scuffing or scoring. It is therefore advantageous to strike a IIhappy naediuna" by renaoving only the sharp peaks of these naicroscopic ridges and in this way still reap the benefits of the oil-retaining grooves. This type of cylinder wall surface is obtained through exercis e of care in finishing operation and through proper use of equipnaent. The following procedure will produce the best results when fitting pistons to sleeves: 2.
ENGINES Super Blue Dianaond Section B Page 13
be naoved up and down at a speed rate of approxinaately one stroke per second.) Using 2S0-grit hone stones and having both sleeve and stones coated with vegetable shortening, work hone up and down in the cylinder bore approxinaately 20 strokes. This operation should bring the bore to the desired size.
3. Still using 2S0-grit hone stones, but having lubricant only on the stones, pass the hone up and down in the bore about 5 tinaes. This operation will not increase the bore dianaeter but will naerely serve to renaove the sharp ridges and leave the desired type of surface finish. NOTE: In steps 1 and 2, the hone should be quite snug in the bore. In step 3, the tension should be a little less. CAUTION: Extrenae care naust be taken to aSsure thatno abrasive renaains in the en gine. 4. After engine has been reassenabled, it should be allowed to run-in for two or three hours at a fast idle (approxinaate1y 1200 r.p.na.).

If canas haft bearing replacenaent is neces sary,renaove and install new bushings with special canas haft bearing installation tool. Noreanaingis required. Fig. 27 illustrates the use of canashaft bearing installing tool.
Bushing arbors
Camshaft bushings
A22149
Fig. 27 - Using the install ing tool.
SE-172Q Camshaft
Bushing
Connecting Rod and Piston Disassembly

1. Renaove piston-pin retainers frona each
piston, and renaove piston rings frona pis ton ring grooves. 2. Heat piston in boiling water or piston heat er. Place piston in piston vise, and using pin-driving tool, drive piston pin frona
1.
Using 150-grithone stones and having both sleeve and s tones coated with one of the vegetable shortenings (Crisco, Spry, Dexo, or equivalent), work hone up and down in cylinder approxinaately 20 strokes. This should bring the bore dianaeter to within .0003" of the desired size. (Hone should
PRlNTED IN UNITED S'tATES OF AMERICA

Press ram ----iII"1
piston and connecting rod (Fig. 28). After piston pin is removed, lift piston from
connecting rod.
r"
Fig. 29 - Use SE-1036-~ to remove bushing. Select proper hole in SE-1033 Support plate to permit clearance for bushing.
Press ram
--~
Adapter -_-'_'
A-22205
Fig. 28 - Use suitable piston vise to hold pis ton and drive pin out with SE-1263 Piston Pin Driver. Use soft hammer.
3. Wash all parts in a cleaning solvent. CAUTION: Do not use a caustic solution for ah.uninurn pistons. Clean the carbon from piston ring grooves with a broken ring or ring groove cleaner. 4. Inspect connecting rods, caps, and bearing shells. All connecting-rod bearings and piston-pin bushings should be replaced at every major overhaul. Test rods for align ment. Rods only slightly misaligned can be straightened with proper equipment. Badly twisted or bent connecting rods must be replaced. 5. Inspect pistons for cracks, breakage, or scores. Check piston ring grooves and ring lands for wear, using a new piston ring and feeler gauge. If clearance be tween ring and ring land exceeds .005", (total clearance) replace piston (see spec ifications). Pistons which are scored or damaged, must be replaced. 6. Inspect piston pins for wear, and if wear is perceptible, replace pins. Replace piston pins which show signs of corrosion or etching. 7. With properly fitting adapter, press old piston-pin bushing from connecting rod (Fig. 29). Place new piston-pin bushing in position, align oil hole in bushing with oil hole in connecting rod, (Fig. 30), install bushing with a .0035 11 to. 0055" press fit. Burnish bushing into place in the connect ing rod (Fig. 31), then ream pin bushing to provide a hand-push fit. 8. With reamer, ream piston pin bosses in piston to provide a tight fit of from .0000"
Burnishing bar
Fig. 31 - Burnish bushing using SE-879.

to .0002" with piston pin. NOTE: When fitting piston pins, the pins should be at room temperature (70 0 F) and the pistons should be heated to approximately 200 0 F

in boiling water or piston heater. The pin should be a lIpalm-push" fit under these conditions.
ENGINES Super Blue Diamond Section B 15
Piston Fitting
When fitting pistons in the cylinder sleeves, use a .003" feeler ribbon l/Z" wide between the piston and cylinder 90 0 from the piston pin hole and in line with the thrust face of the piston {Fig. 3Z}. Apply a tension pull on scale to the feeler ribbon, and check clearance to specifica tions as outlined in the chart. ' Feeler Gauge Ribbon Checking Width . . . . . . . . . . Thickness . . . . . . . . Tension on Scale (Lb.) Desired Tension (Lb.) l/ZII
.003 l1
6-18 12
Fig. 33 - Checking ring gap.
Piston ring
expander
Fig. 3~ - Instal1ingpistonring using Ring installing tool.
SE-II~9-8
Fig. 32 - Checkingpistonfit using feeler gauge ribbon. SE-I007 Gauge Set is available for this operation.
Connecting-Rod and Piston Assembly
1. With piston heated to approximately ZOOO
F., support connecting rod in vise, push piston pin into piston bosses while piston is hot. When assembling piston on rod, the slot in the piston skirt must be toward the camshaft side of the engine, which is the numbered side of the connecting rod. Install piston-pin retainer in piston at each end of pin, making sure that retainers seat fully and with tension in grooves. Test. connecting-rod and piston assembly on a connecting-rod aligner, and correct any misalignment. Z. Place piston and connecting rod in vise. Test each piston ring for proper gap by placing in cylinder and measuring gap with feeler gauge. Gap should be .016" to .OZ6" (Fig. 33).
PRINTED Hi UNITEO STATES OF AMERICA
3. When installing piston rings in piston grooves, be careful not to distort rings. If possible, use a suitable piston ring ex pander tool {Fig. 34}. Also check new piston rings in piston ring grooves for clearance between ring and ring lands. The correct ring clearance is shown in specifications.
Crankshaft Cleaning and Inspection

1. Wash and clean crankshaft with cleaning
solvent or steam. Z. Inspect main-bearing and connecting-rod journals for wear. If journals show wear or out-of-round in excess of .003", the shaft should be either reground and under size bearings installed. or replaced. Use micrometers for checking.
3. Check crankshaft and flywheel dowels for damage and fit, and replace if worn or damaged. 4. Examine crankshaft timing gear teeth, and replace gear if teeth are worn or damaged.
5. Install Woodruff key in groove in crank shaft. Heat crankshaft gear in boiling water

cover, flywheel housing, and other parts that were removed during disassembly of engine and were not covered by procedure. Wash in cleaning solvent or stearn clean preliminary to inspection. 2. Check all twelve valve lifter or push rods for straightness by rolling on flat surface. Replace any that are bent or have loose ends. 3. Inspect oil pan for cracks or deep bends, and straighten or weld. 4. Inspect oil pan drain plug and drain plug boss for fit and thread wear. If plug is loose or threads are damaged, repair threads or replace oil pan. 5. Inspect crankshaft pulley and vibration damper assembly for evidence of rubber coming loose from pulley, and inspect for wear. Replace damper assembly if either condition is encountered. Do not submerge vibration damper assembly in hot cleaning solvents. Inspect crankshaftfan drive pul ley for wear in hub bore. If inner diameter of bore is worn, scored, or Woodruff key way damaged, replace pulley. 6. Inspect engine gear case cover, and re place if cracked or broken. Remove old cover seal and install new seal. 7. Check each of twelve engine valve tappets for irregular wear, chipping, cracking or scores. Replace defective tappets.
or piston heater. This will expand the gear enough to allow it to be tapped onto the crankshaft without the danger of damaging the gear. A special crankshaft gear in stalling tool is available under SE-I088.

1. Clean flywheel and ring gear with a clean
ing solvent, remove all traces of oil and grease. 2. Inspect the flywheel ring gear. If any teeth are damaged, or if ring gear is loose on flywheel, the ring gear must be replaced. 3. Check the flywheel dowel holes and mount ing bolt holes for wear, also check for fly wheel having been loose. 4. To replace flywheel ring gear, heat gear with torch, and remove from flywheel with a hammer and drift. Heat new ring gear with torch, heating evenly all the way around. While the ring gear is hot, install gear on flywheel and allow it to cool. 5. Check pilot bearing in flywheel for wear or damage and replace if needed. 6. Install flywheel on crankshaft. Install six self-locking capscrews, drive dowel pins through flywheel to crankshaft.

1. Wash camshaft in cleaning solvent, brush
ing to facilitate removal of all sludge or carbon deposits. 2. Inspect camshaft journals for wear or out-of-round. signs of
3. Inspect oil pump drive gear in center of shaft. If teeth are worn or damaged, the camshaft must be replaced, as the gear is integral with shaft. 4. Inspect camshaft lobes. If worn, chipped, or scored, replace the camshaft. 5. Inspect camshaft gear, and replace if wear is evident or gear teeth are nicked or otherwise damagl';d. 6. To reassemble, install thrust flange over end of camshaft. Install Woodruff key in slot in shaft. Place camshaft gear in boil ingwater or piston heater, and install over Woodruff key. Install camshaft nut and tighten to approximately 120 foot-pounds tension.
8. Inspect engine flywheel housing for cracks or breakage and replace if damaged. In spect flywheel housing to crankcase pilot dowel holes for wear. If wear is evident, drill or ream the holef: and install over size dowels. Also inspect dowels for wear and replace if wear is evident. 9. Inspect all caps crews and nuts for thread wear or breakage. and replace as neces sary. Use new lockwashers when reassem bling engine. 10. All gaskets and oil sales must be replaced at each overhaul or major repair.
ASSEMBLY OF ENGINE
When all parts have been cleaned, inspected and repaired, and necessary replacement parts have been procured, install engine cylinder block in engine overhaul stand for reassembly.

1. Cleaning mis cellaneous engine parts. This includes brackets, oil pan, engine case
Main-Bearing and Connecting-Rod Bearing Installation

It is essential that main bearings be in alignment with the crankshaft journals. 'The

model BD engines do not have the bearing caps piloted in the crankcase. When no means of piloting the bearing caps has been provided, misalignment is possible due to a slight shift ing of the bearing caps when the bearing cap bolts are tightened. If a bearing cap bolt is not straight or if the threads are not concentric with the body of the bolt, this condition will be aggravated; therefore, all bolts should be care fully examined before installation, to avoid such a condition. The following method has proved success ful in holding the caps and bearings in align ment with the crankshaft. After bearings have been fitted to specified clearances, remove the caps and apply a coating of petrolatum or white vaseline, or heavy engine oil to the bearing surfaces, then reassemble the caps and tighten the bolts.
It will be noted that a small quantity of the petrolatum or vaseline may be squeezed out when the bearing caps are tightened; however a sufficient quantity will remain which will serve as a cushion or filler between the bearings and crankshaft journals, thereby reducing the tend ency of the cap and bearing to shift.
between the bearing back and the bore. This increased diameter is referred to as bearing IIcrush" (Fig. 35),
Difference between diameters (A) and (B) is bearing crush (C)
Diameter (A) at right angles to parting lines greater than diameter (B)
With bearing cap drawn up tight diameters (A) and (B) are equal
A22SS0
Fi g. 35
To obtain proper bearing assembly with the correct "crush", care must be taken when tightening the clamping bolts to make sure they are drawn down alternately and evenly, using a tension wrench and tightening as specified. As a result of excessive bearing crush, due to reworking the caps, the rod or main bearing bore will possible become distorted because more force is required to draw the cap and housing together. Rods, caps, or blocks must not be filed, lapped, or in any other manner reworked in order to reduce clearance. While such practice will make a tighter fit at top and bottom, it will result in an out-of-round bore and bearing shell distortion. New bearing shells will have to be installed eventually and that is when addi tional trouble starts. In general, a visual inspection of the part ing faces of the rod or caps under a magnifying glass will provide sufficient proof of any attempt at reworking. Under the glass, the parting line surface of standard parts will show the manufacturing cutter tool marks and will not have a polished or extremely smooth appear ance. On the other hand, reworked parts will have a polished surface and, if a file was used, will show the even pattern of the file teeth. Seriousness of this condition is in direct pro portion to the amount of reworking. BEARING SPREAD. Main and connecting rod bearings are designed with the "spread" (width across the open ends) slightly greater than the diameter of the crankcase bore or con necting-rod bore into which they are assemblied. For example, the width across the open ends of the BD engine connecting-rod bearing not in
The petrolatum or vaseline will also serve as a lubricant when the engine is first started and will dissolve and mix with the regular engine lubricating oil after a few revolutions. Under no circumstances should anything other than petrolatum or vaseline or heavy engine oil be used due to the possibility of chemical reactions which would cause damage to the bearing material. BEARING CRUSH. Undersize preclslon type bearing shells should be ins taIled when, be cause of wear, bearing-to-crankshaft running clearances are to be reduced. Bearing caps mus tnot be filed, lapped, or in any other manner reworked. Premature bearing failure will result from attempts to reduce journal-to-bearing running clearance by reworking of either bearing caps, bearings, or both, because such reworking will alter the engineered fit of the bearing shells in their bores and destroy the specifically desired "crush", When installing precision type connecting rod or main bearings, it is important that the bearing shells fit tightly in the rod orcase bore. To accomplish this, the bearing manufacturer makes the diameter at right angles to the part ing line slightly larger than the actual diameter of the bore into which they are assembled. When the assembly is drawn up tight, the bear ing is compressed, assuring a good contact
place is approximately .025" more than when the bearing is in position in the rod. This condi tion causes the bearing to fit snugly in the rod bore and the bearing must be "snapped tr or lightly forced into its seat (Fig. 36). Rough handling in shipment, storage, or normal results of use in an engine, may cause the bearing spread to be increased or decreased from the specified width. Bearing spread should, therefore, be carefully measured and corrected as necessary before installation in an engine. Bearing spread can be safely adjusted as follows, although care and judgment should be exercised in the process:
If measurement of 1. Excessive spread. spread indicates that distance "A" is ex cessive (see chart for specifications), place bearing on a wood block and strike the side lighrly and squarely with a soft mallet (Fig. 37. Recheck measurement and, if necessary, continue until correct width (measurement HAil in chart) is obtained.
O. D. OF BEARING WHEN INSTALLED IS THE SAME AS THE DIA. OF THE CRANKCASE OR CONN. ROD BORE
1IIIII---JlA"----------------~
SPREAD OF BEARING
BEFORE INSTALLATION
- - - - - - - - - - - - - A-J6088
Fig. 36
2. Insufficient spread. If measurement of spread indicates insufficient spread, place bearing on wood block and strike the back of the bearing lightly and squarely with a soft mallet (Fig. 37). Recheck measure ment and, if necessary, continue until cor rect width (measurement "A" in chart) is obtained. Chart of Bearing Spread Dimentions.
BD Engine (Minimum)
Connecting-Rod Bearing 2.237 11 2.875"
SOFT MALLET
(STRIKE LIGHTLY
AND SQUARELY)
+ .025" + .025"
IMain Bearing
1. INSTALL CRANKSHAFT AND MAIN BEARINGS. Clean all surfaces of crank shaft bearing journals and wipe clean the bearing bores in the cylinder block. Re move bearing cap self-locking capscrews and bearing cap. Wipe backs of cylinder block half of bearings, making sure that dirt and oil is removed. Place bearing shell halves in position in bore in cylinder block, making sure that bearing shells are fully seated, that oil holes in bearing shells line up withoil holes in cylinder block, and that locking tongs on bearings fit into re cesses. Follow same procedure, place bearing shell cap halves in bearing caps. Place a film of engine oil on bearing shell surfaces and lift crankshaft to align itself in the bearings, and also provide lubrica tion. Place bearing caps and bearing lower halves over crankshaft journals. Be sure bearing caps are properly installed with numbers to camshaft.
DECREASING SPREAD
SOFT MALLET (STRIKE LIGHTLY AND SQUARELY)
INCREASING SPREAD
A-J609S
F j g. 37

2. In order that an accurate measurement can
be made to check all bearing clearances, a material similar to "plastigage ll or fvirgin lead lf can be used. 3. Use the following instructions when using f'plastigage lf
(d) Rock the crankshaft back and forth two or three times. Further tighten bolts to 60 to 70 foot-pounds and again rock the crankshaft two or three times. Tighten bolts to 105 foot-pounds and remove bearing cap. (e) The virgin lead will now be compres sed exactly in accordance with the amount of bearing to crankshaft clear ance. Peel off flattened piece of virgin lead wire and measure with microm eter. Thickness of flattened piece of wire is exact amount of bearing clear ance present. Repeat above operations on all bearings. 5. If clearance is not within .0013 11 - .0043", either use undersize bearing, regrind shaft, or replace shaft. Check crankshaft for end play which is taken up by number four main bearing. End clearance should be from .013 11 to ,005". 6. INSTALL FLYWHEEL HOUSING. Place flywheel housing in position over two fly wheel housing to cylinder block dowels and tap into place with soft hammer. Install six capscrews and lockwashers in flywheel housing. If efther block or flywheel housing is replaced, the flywheel housing will have to be aligned with a dial indicator. When correctly aligned, run-out of bore should not exceed .005" (Fig. 39). NOTE: If pos sible align flywheel housing while engine is in overhaul stand and with engine in vertical position (flywheel housing up).
(A) Remove oil from bearing cap insert

and exposed half of crankshaft journal. (B) Place a piece of l'plastigage" the full width of the bearing insert. (C) Reinstall the bearing cap. Tighten the self-locking capscrews to approxi rn.ately 105 foot-pounds.
(D) Remove the bearing cap.
The flatten ed plastic material will be found ad hering to either the bearing shell of the crankshaft.
(E) To determine the bearing clearance, compare the width of the flattened plastigage at its widest point with the graduations on the envelope (Fig. 38). The number within the graduation on the envelope indicates the clearance in thousandths of an inch. NOTE: Do not turn crankshaft during the above procedure.
Fig. 38 - Checking bearing clearance.

4. When using the 'virgin lead method" use the following procedure: (a) Virginleadwire ofapproximately.OlO" thickness should be used. If wire of .010" thickness is not available and thicker wire must be used, it must be rolled to approximately .010" thick ness. (b) Remove one bearing cap. Place 1/2" piece of virgin lead length wise on top of crankshaft bearing journal. (c) Install cap and beari.ng shell half. In stall bearing cap bolts and tighten to 30 to 40 foots-pounds tension.
F'~INTED
A-22526
Fi g. 39
IN UNITi!.O STA'te.$ OF" AMERICA

into recess in cap. (NOTE: See instruc tions under "Main Bearing and Connecting Rod Bearing Installation".) 3. Coat bearing surfaces with oil. Pull con necting rod into position on crankshaft journal and install connecting-rod cap and bearing. NOTE: Bearing cap must only be installed on connecting rod one way, with both connecting rod number and bear ing cap number to camshaft side. Install two self-locking capscrews and tighten to 65 foot-pounds, use tension wrench. 4. To check connecting-rod bearing to crank shaft clearance, follow procedure given for 'plastigage" on IIv irgin lead" test. Spec ified connecting-rod bearing to crankshaft clearance is from .0007"-.0032". Do not attempt to file connecting rods or bearing caps.
7. INSTALL ENGINE FLYWHEEL. Place engine flywheel and ring gear into position on dowels in crankshaft flange. Install six self-locking capscrews in flywheel and crankshaft flange, and tighten to a tension of approximately 100 foot-pounds, using a tension wrench. 8. INSTALL GEAR CASE COVER PLATE. Place plate and gasket at front end of engine cylinder block. Install one capscrew and lockwasher. 9. INSTALL CAMSHAFT AND GEAR. Coat camshaft with engine oil. Insert camshaft into front end of engine block, being care ful not to damage camshaft bearings. Before completely entering camshaft ro tate shaft until marked teefh on crankshaft gear and camshaft gear index (Fig. 14). Install two capscrews and lockwashers in camshaft thrust flange, working through large holes in camshaft gear. Rotate crankshaft and camshaft to determine that gears do not bind or interfere. Back-lash must be from .000" to .002" (.0015" pre ferred). 10. INSTALL GEAR COVER CASE. Place gasket in position on case cover. Place crankshaft oil slinger ove r end of c rank shaft and install Woodruff key for fan drive pulley in crankshaft. Place gear case cove r in position. Install capscrews, new lock washers and nuts. 11. INSTALL FAN DRIVE PULLEY AND VIBRATION DAMPER. Heat crankshaft fan drive pulley and vibration damper assembly in boiling water. When heated, quickly install assembly on crankshaft and install washer and fan drive pulley nut. Tighten nut with wrench of about 36" lever age.
5. Follow procedure outlined in steps above for remaining connecting rods and pistons. 6. INSTALL CLUTCH Install clutch driven disc against flywheel so that the long por tion of the hub is toward the rear. Place clutch in position on flywheel over clutch driven disc. Locate clutch so that arrow or inspection mark (usually a dab of white paint) on flange of clutch backing plate or cover is as near as possible to the letter ilL" on the flywheel, and install two or three mounting capscrews and lockwashers loosely. Insert a clutch aligning arbor, if available, or a transmission main drive gear shaft, through clutch driven disc hub spline and into clutch pilot bearings. Hold clutch driven disc in position while com pleting installation of six mounting cap screws and lockwashers in flange of clutch backing plate or cover. Tighten all six capscrews securely. Remove three retain ing capscrews and flat washers which were installed to hold clutch compressed. NOTE: clutch will not operate properly unless these retaining capscrews are removed. 7. INSTALL VALVE TAPPETS. Coat each of twelve valve tappets with heavy engine oil and drop each, flat side down, through recess in side of cylinder block into sock ets in block. 8. INSTALL VALVE LIFTER ROD COVER. Install new gasket over opening at left hand side of engine block. Install valve lifter rod covers and slotted screws.

1. Install one connecting-rod and piston assembly down through top of cylinder block having slot in piston towards cam shaft side of engine. Pistons are also marked with an arrow indicating front of engine. Use a piston ring compressor sleeve to compress piston rings and thus avoid possible ring damage. 2. Wipe bore of connecting rod free of oil and dirt. Place bearing shell upper half in connecting rod bore, being sure that oil hole aligns with oil hole in connecting rod and that locking tangs of bearing shall fit into recess. Clean connecting-rod cap bearing bore and clean back of bearing. Place bearing shell lower half in connecting rod cap, making sure that tang of bearing fits

1. INSTALL HEAD. Place gasketon cylinder block and align bolt holes Place cylinder head on crankcase, being careful not to damage or shift gasket position. Loosely

install all cylinder-head bolts and flat washers, omitting bolts in holes for rocker arm assembly. 2. INSTALL VALVE ROCKER ARM ASSEM BLY. Insert twelve valve lifter rods in cylinder head, make sure they enter the valve tappet. Lift the valve rocker-arm assembly into position on cylinder head with the drilled oil bracket on the front end. Install the remainder of cylinder-head bolts and tighten alternately and evenly in sequence to BO foot-pounds (Fig. 40). Be sure to place stud with oil hole in the left front cylinder-head bolt hole. Retighten cylinder head after engine has been oper ated for a short period.
pilot rings and gasket, tilt bottom of mani fold toward engine block. This will force manifold out at top enough to bind against the two capscrews and hold manifold in position until the front and rear cap~crews can be installed.
6. INST ALL
WATER PUMP Place water pump gasket in position, at water pump opening in front of cylinder head. Install water pump and fan and install three cap screws and lockwashers in pump and cyl inder block.
7. INSTALL OIL FILTER.
22
20
"
14
10
0
'\
I)
o o '---_"
I f ,
o ,---"
I~
o
.'---'
/ \
o
/--',
13
19
21
0/--,
'\ " '\
_---, 0
Place oil filter and new gasket in place on cylinder block. Install four capscrews and lockwashers in oil filter base. (NOTE: Be sure filter assembly is thoroughly cleaned and a new cartridge is installed before replacement on engine.)
,,
0\ .....
::
~:
~:
!:
,'\
,'''
'\
,/g"-o
16
-"~"'---"r'--,"~--0 0 0
,'\
/',.
,'g'"
0
,'\
/~~
0
B. INSTALL ACCESSORIES.
18
15
23
A8337
Fig. 4-0
3. ADJUSTING VALVES. To adjust valve stern to valve rocker arm clearance cor rectly, each cylinder must be on top dead center on its compression stroke at the time of adjustment of valves for that cyl inder. To determine the correct position, turn the engine crankshaft until No.1 piston is at top dead center on compression stroke and the ignition timing mark on the crankshaft pulley in line with the pointer on the timing gear case. Adjust clearance on each valve of No.1 cylinder to .01B" to . 020" by using a feeler gauge between valve stern and valve rocker armand turn rocker arm adjusting screw out of rocker arm until clearance is obtained. Tighten ad justing sc rew lock nut and recheck clear ance. (NOTE: Valve clearance should be rechecked with engine at normal operating temperature.) Turn crankshaft one-third revolution and adjust clearance on No.5 valves. Work ing in firing order sequence, continue to set valves of each of the remaining cyl inders, turning crankshaft one-third turn after each valve adjustment. INSTALL INTAKE AND EXHAUST MANI FOLDS. To facilitate installing the mani folds. after manifold gaskets and pilot rings are installed, start capscrews at end of intake manifold. This will permit the manifold to slide straight up between the engine head and capscrews and flat washers. When manifold is lined up with
PRINTED IN UNITED STATES Of'" AMERICA
Install carbur etor, generator, distributor and connecting wires, starter, fuel pump, ignition coil, gauge, and thermostat. Tighten fan belt sufficiently to secure 1/2" depression on belt midway between generator pulley and fan pulley.
9.
FILL ENGINE WITH OIL. After making certain that oil drain plug is securely in stalled, fill crankcase with oil. After en gine has been installed and placed in oper ation, again recheck oil level and add as necessary to bring oil level to full mark.
10. INSTALL CYLINDER HEAD COVER If engine is not to be installed at this time, install new cylinder-head cover gasket and install cylinder-head cover. Install three flat washers and three nuts on cover.
ENGINE MOUNTINGS
Fig. 41 and 42 illustrate engine front and rear mountings.
4.
ENGINE GEAR CASE COVER INSULATOR RETAINER
~.....--
5.
t:=IIF-'-- WAS HER
INSULATOR \E~=====j~=~~Tf~- WASHER LOCKWIRE

A.I60Ia
Fig. 4-1 - Front mounting.

Engine support Upper insulator Lower insulator Washer Cross member
Engine rear support

Fig. 42
Cartridge
A-22527
\
Return channel
OIL FILTER
1. The DeLuxe oil filter is used on the BD engines and incorporates a removable sump
(Fig. 43). 2. Water, grit, metal particles, sludge and other contaminants that settle out of the oil are held in the sump away from the cartridge. When the cartridge is changed the cartridge and sump quickly and easily lift out as a single unit. Change filter cartridge and clean sump at regularly es tablished periods; according to operating c ondi tions .
3.
When reassembling filter unit after com plete disassembly: tighten center tube nut securely using wrench SE-l 728.
CRANKCASE VENTILATION
The BD engine has a crankcase ventilator metering valve installed at the rear left side of engine on the tappet cover. To remove valve, disconnect the vacuum line and unscrew unit from tappet COver plate. To service, separate the two halves of the unit and remove weight. Clean all parts thoroughly. When reinstalling the valve, make sure the arrow on the housing is pointed up. (Fig. 44).
Metering orifice Upper housing "",7'r--"'~ Small section of Weight Large section of metering pin in orifice restricts flow of air
Gasket
Relief valve spring
/""7-T7"">
mete~~ilrt' G,,,,,, c~in

..;' Grooves
;
Lower housing
Weight Position of weight with high manifold vacuum (above 3~ to 411 inches mercury) A.23449
Relief valve
Fig. 43
Gasket
84744
Position of weight with low manifold vacuum (below 3~ to 4~ inches mercury)
Fi g. 44
ENGll'JES Super Red Diamond Section C Page 1
SUPER RED DIAMOND ENGINE
-
'"
c:
>
.... o
(I.l
en
.
u..
PRINTED IN UNITED STA'f$ OF' AMERICA
ENGINES Super Red Diamond Section C Page 2

7. The detachable cylinder head is bolted to the crankcase, and a gas-tight and water tight seal is maintained by means of a gasket. The crankshaft is a drop forging of heat treated steel. It is counterweighted, bal anced both statically and dynamically, and ground to close limits. The shaft is mounted in seven precision-type replace able shell bearings, the number seven (rear) bearing taking up the thrus t. The rear main bearing is made up of two shell halves together with four thrust flanges. The two lower thrust flanges are held in position by dowels in the main bearing cap. The pistons are made of an alUIninum al loy, are cam ground, and are fitted with three compression rings and one oil con trol ring. The full-floating type piston pins are held in place in the pistons, at the ends of the pins, by snap rings.
DESCRIPTION
General
The Model RD, Super Red Diamond engine is a 4-cycle, 6-cylinder-in-line, overhead valve type engine (Fig. 1). The engine serial number is stamped on a pad at the front on the left side of the crankcase just below the cylinder head. The block has dry-type replaceable liners for the cylinder. The detachable cylinder head contains all valves, valve guides, and springs. The cylinders are numbered from front (fan and timing gear end) to rear. Engine crank shaft rotation is clockwise, as viewed from the front end ofthe vehicle. The intake and exhaust manifold, carburetor, and generator are located on the right side of the engine. The distribu tor, starter, fuel pump, and oil filter are lo cated on the left side. The oil filler inlet is located on the left side of engine at the front. The bayonnet type oil level gauge is located on the left side. The water pump is located at the front of engine. 8.
9.
10. The camshaft is machined from a solid drop forging and mounted in four special replaceable bearings. 11. The flywheel is bolted and doweled to the crankshaft flange. The timing mark is located on the front crankshaft pulley.
Construction
1. The generator, fan', and water pump are driven by V -type belts from a driven pul ley mounted on the front end of the crank shaft. The distributor, mounted at the left side of the engine, is driven by the cam. shaft through the oil pump.
ENGINE REMOVAL
Disconnect the following electrical cir cuits, hose connections, and various units as outlined:
2. The exhaust and intake manifolds are bolted to each other and to the right side of the engine head. The intake manifold is cas t in one piece. The exhaust manifold is made of three parts which are held together by expansion clamps and seal. 3. A vibration damper is provided atthe front end of the crankshaft. 4. The cylinder block and crankcase are cast in one piece, and carry the crankshaft main bearings. Water circulation pas sages completely surround the cylinders in the crankcase and also provide coolant to the cylinder head. Oil is supplied under pressure by the oil pump to the engine lubrication system. Oil spray from the revolving crankshaft is distributed to the cylinder walls, pistons, and other moving parts inside the engine.
1. Drain engine oil pan.
Drain all coolant from engine cooling system by opening the drain cock on side of engine as well as the radiator drain cock. Remove radiator filler cap when draining cooling system.
2. Disconnect upper and lower radiator hose connections. Disconnect engine air cleaner and remove air cleaner. Disconnect vac uum line at manifold. (Air line at com pressor when vehicle is equipped with air brakes.) . 3. Disconnect engine circuit Wlrlng. This includes coil wire, starter cable, engine ground strap and instrument sender unit wires. 4. Disconnect fuel line at fuel pump. Discon nect throttle control linkage and remove choke wire at carburetor. 5. Remove hood and floor boards. Remove fenders and radiator grille as a unit. 6. Remove radiator mounting bolts and lift out radiator support and core assembly.
5.
6. Exhaust valve seats are of alloy and are pressed into place. These valve seats lengthen the period between valve recondi tioning operations. Valves and valve seats are cooled by continuous circulation of water through the cylinder head.

7. Remove ending front mounting bolts from support bracket. These are the bolts at the front crossmember. 3.
Remove rocker-arm assembly as a unit (Fig. 3).
8. Support transmission using floor jack or suitable blocking. Remove caps crews from around bell housing.
9. Disconnect engine exhaust pipe at manifold.

10. Attach engine sling to front and rear right
side cylinder head bolts and remove en gine.
ENGINE DISASSEMBLY
Install the engine ina suitable rotating en gine overhaul stand. NOTE: Many of the dis assembly operations can be performed with the in the chassis. However, the following disassembly outline is performed with the en gine removed from the chassis to clearly illus tra te each of the units. Except where indica ted, no attempt has been made to prescribe a par ticular sequence for removing the various units, since some can be readily removed with the engine in the chassis. The extent of the service required on a particular unit will gov ern the necessity for its removal.
Fig. 3 - Removing Rocker
Ar~
Assembly
Rocker-Arm and Valve Mechanism Disassembly

1.
The rocker-arm assembly is com.posed of front and rear shafts joined at the center, on which are mounted twelve rocker arms and four tension springs. The shafts are mounted in seven brackets, and are pre vented from turning at the two center brackets which contain locking washers fitting into slots in the shaft. Remove locking washers from two center brackets (Fig. 4),

The following steps are to be followed when removing the rocker-arm cover and rocker-arm assembly. (Carburetor and air cleaner previously removed):
1. Remove four nuts from rocker-arm cover.

Remove air cleaner line and remove cover. 2. Remove nuts, capscrews and oil bolts from shaft brackets. NOTE: Third bolt from the rear on the left side of the cylinder head supplies oil to rocker arms (Fig. 2).
Fig.
2. 3.
ij
Separate the shafts, and slide rocker arms, springs, and brackets from shafts. Clean all parts in a solvent cleaning fluid, being careful to clean all accumulated sludge and carbon deposits from oil holes and slots.

Carefully inspect all parts for defects and wear.
1. Inspect rocker-arm shaft and expansion

plugs. Check on a surface plate for signs of bending, check for wear from rocker arms. If a shaft is bent or shows percep tible wear, it must be replaced.
Fi g. 2
PfUNTEO IN UNITEO STATES OF """ERICA
2. Inspect rocker-arm adjusting screws for wear at contact surface and for thread wear. Replace worn screws. Check rocker-arm bushings. Inspect valve stern contact pad surface of rocker arm, and resurface if wear is perceptible. Do not remove more than .010" of material when resurfacing rocker-arm pads. 3. Inspect tension springs for breakage or loss of tension. Replace defective springs.
"''---Busbing installing tool
Re-Bushing Rocker Arms

With properly fitting adapter of special tool equipment provided (Figs. 5. 6 and 7), press old rocker-arm bushing from rocker arm. Place new rocker-arm bushing in posi tion. Align oil hole in bushing with oil hole in rocker arm, which is located approximately 30 0 from top of rocker arm toward rocker -arm adjusting nut. Using installing tool, press new bushing into rocker arm. Burnish bushing into place in the rocker arm, theft ream rocker arm bushing to provide .0015 11 to .004" clear ance. Ream dimension is .8745" - .8760".
~--
Fig. 6 -Showing lllethod of installing new Rocker Arm Bushing.
Press ram
""---Burnishing tool
~-----Bu&hing
removing tool
... ~ Press plate
Fig. 7 - Burnishing Rocker SE-879 Burnishing Tool.
Arm BUShing.
Use
Fig. 5 - Use SE-I036-2 Bushing Removing Tool when removing the rocker arm bushing. Support the rocker arm on the SE-I033 support block. Select a hole in the support block to properly support the rocker arm at the same time permit the bushing to clear the support block when being removed. Use the support block when in stalling and burnishing the new bushing. Cylinder Head and Valves
The following ins tructions are to be ob served when reconditioning cylinder head and valves: Remove push rods (Fig. 8). Remove caps from end of exhaust valve stems, remove cylinder-head bolts and lift off cylinder head and gasket. Place cylinder head on bench. 1. Compress valve spring with a valve com pressor and remove valve spring retainer locks. Remove retainer. Remove outer spring and inner spring. Remove valve
Fig. 8
spring spacer. NOTE: Valve springs are installed with close-coiled ends toward the cylinder head. Remove all valve springs as outlined.

2. Invert cylinder head. Remove all valves from their valve guides and from the head, keeping each valve in a suitable rack which will assure replacement of the valves in their original location. 3. Scrape all carbon from cylinder head com bustion chamber, and clean any gasket material from surface of head. Clean the head using steam cleaning or other suitable cleaning equipment. 4. Clean all carbon deposits from valve heads and valve stems with wire brush. Wash all valve springs and retainers in cleaning solvent.
cracks or sand holes and if found defec tive, weld or replace head. 2. Inspect exhaust valve seat rings for loose ness and inspect for excessive width of valve seat surface (Fig. 9). If insert rings are loose, replace. If a seat has been pre viously ground to such extent that it can~ot be narrowed from top to bring to proper position near center of valve face, the ring must be replaced.
Inspection of Valve Guides, Valve Springs, and Valves

1. Clean valve guides with a suitable cleaning tool (Fig. 10). Check each valve guide with a "Go and No GO" gauge (Fig. 11), if avail able; otherwise, use a new valve to check fit. If "No-Goll portion of gauge enters, the guide must be replaced. Recommended valve stem to valve guide clearance is

1.
Inspect cylinder head visually for signs of
Preferred . . . . . . . . - - - - Minimum seat
3/32"
Fig. 10
Preferred . . . . . . . Maximum seat
W'
Fig. 9 - Valve Seat Widths, Exhaust.

Fig. II - Use SE-II~5 "Go and No-Go" set.
or
AMERICA

3. Inspecteach valve for warpage, for severe ly burned condition, and for excessive grinding on the valve head. Inspect valve stem for scuff marks or perceptible wear. Inspect valve stem end for wear at contact surface with valve rocker arm. If valve is warped, excessively burned, or has been previously ground to extent that valve head is thin at edge, replace valve; otherwise, valve can be reconditioned and reinstalled.
from .002" to .004" for exhaust valves, and from .0015" to .0035" for intake valves. Clearance in excess of .006" for intake valves or .008" for exhaust valves, re quires guide replacement. Valve guides are reamed to .437" after assembly (Fig. 12) .
Rotating Exhaust Valve Mechanism (IISlo-Roto

Valves")
Valve burning is commonly caused by deposits accumulating on valve seat, thus hold ing valves open to be burned to escaping ex haust gases. Carbon deposits collecting under valve head hold valves open, further causing blow-by. With the valve slowly rotating, these accumulations are kept from forming to a great degree, thus improving valve life. All rotator parts are interchangeable, but should be checked after assembly to insure proper clearance re quired for rotation. Care should be taken not to damage or nick valve stem ends or tips as this will alter the clearance.
Fig"
12
2. Test valve springs (Fig. 13). Test ten sion of each valve spring at valve open length with a valve spring tester. Check inner valve springs at 1-1/211 length, re place if pressure is less than 86 pounds. Test outer spring at 1-45/64 11 length, and replace if pressure is lessthan136 pounds.
The parts involved in the rotating valve mechanism are: special spring seat retainer, a pair of flat half-moon keys, a close fitting cap located on the valve stem, and a specially constructed valve stem. In order to accommodate valve expansion, the tappet lash (valve tappet clearance) must be maintained. When camshaft rotation causes this lash or tappet clearance to be taken up, the cap on the valve stem causes the valve keys to lower the spring retainer, removing the load of the valve springs from the valve before the valve is raised from its seat. A clearance of .002." to .006" should be maintained between the end face of the valve stem and cap (Fig. 14).
mrn
Right installation ......-----Valve spring
~
Key wear
"i
Wrong installation
Spring retainer
___~r----T--- Scale (pounds)

A.2189D
Cap to valve stem clearance .002" to .006" Spring -----~"-"{ Exhaust valve
Valve cap Valve key (lock)
Fig. 13 -Testing valve springs In SE-1565 Valve Spring Testing Tool.
------il....
F j g.
I~
A232D6

This is the distance the spring retainer is lowered before the valve is moved. The slow valve rotating motion is caused by vibration of the valve, the flowing of exhaust gases around the valve head, and a slight rotating motion imparted to the valve by the valve spring.
ReInove cap froIn exhaust valve. (The ro tating feature is used on the exhaust valves only) (Fig. 15). Make sure end of valve stem
Checking Clearance Between Valve Stem

and Cap
Operation of the rotating valve feature re quired that clearance between the valve stern face and valve cap be maintained at all times.
If no clearance exists after assembly, re ITlove cap, wash and wipe clean, then recheck clearance. Examine the keys to see if they are resting against the shoulder of the valve stern properly. If they are in proper position, re place the cap and check again. If clearance still does not exist, remove all parts and ad just clearance by grinding valve stern tip. If clearance is too great, remove enough stock from lower face or skirt of the ~ to reduce clearance to the proper limits. NOTE: Because of manufacturing tolerances, in both valve stern ends and the valve cap, it is possible to select a new cap and valve combination with the required clearance.
Fig. 15
and gauge plunger pin are clean. Place Clear ance Gauge on end of exhaust valve with gauge set at 110" marking. Press the plunger pin of the gauge firmly against the valve stern and tighten claInp screw (Fig. 16). ReInove gauge
Maximum service lift and efficiency is largely dependent upon cap-clearance which should be set at the time of installation at, o.r very near, the low limit of .00211 to provide for the wear factor. Cap-clearance normally increases in service due to wear caused by impact of the half-moon keys against the shoulder on the valve stern. As the cap-clear ance increases, the rate of wear increases due to longer key travel, which increases the im pact. When rotating mechanism parts have been fitted, the same combination or group of parts should be maintained once the engine is placed in service. After the valves have been in oper ation over an extended period, the keys rr.ay show signs of wear at the point of contact with the valve stern. As long as the .00211 to .006 11 clearance is maintained, this wear is not harm ful; however, when reinstalling keys make sure that both parts of the key set are in the same position, with the wear facing in the same direction (Fig. 14). This will eliminate cocking of the spring retainer. The valve keys can be reversed (turned worn side dOwn) to utilize the unworn face of the keys, thus reestablishing the specified cap-clearance. However, when this practice is resorted to, it is important that an accurate check be made to assure that desired cap-clearance is present. Check the rotating valve cap-clearance the special clearance gauge as follows:
Fig. 16 - Showing use of SE-1726 Gauge.

from stern and place valve cap on plunger pin of gauge. The clearance (or lack of clearanc.e) that existed between the valve stern and cap are now transfered to the end of the gauge plunger pin and valve cap and shows in thousandths of an inch on the spindle barrel (Fig. 17). Press
Clearance between valve stem and cap
is transferred to
this point
Gauge spindle - - - . 1 Plunger pin in contact with end of valve stem Spring retainer Screw
~fA.o.....- - - - -
Valve cap
~~~ I~~'-.-.-- Valve key Ilock I

--l~...<
Spring _ _ _
Exhaust valve
A-2320S
~sing
Fig. 17
ENGINES Super Red Diatnond Section C Page 8

4. Grind valve seats in cylinder head to 45 0 for exhaust and 150 for intakes.
the cap firmly against the gauge. Turn spindle of gauge to right or left until cap bottoms on gauge pin, and rim of cap just contacts top of gauge. Read gauge. Readings to right of Zero indicate positive clearance (see "BII in Fig. 18) and readings to left indicate negative clearance

One ofthe principal difficulties experienced in reconditioning valves is obtaining nearly identical angles on the valve seat and valve face. The importance of these angles in the grinding operation cannot be overemphasized, because it is impossible to produce a flat or square seat by lapping. The grinding stones on both the valve re facing machine and valve seat grinder should be dressed before starting a reconditioning job. You will be unable to determine how closely the angle of the seat will match the valve face until the valve and seat have been ground and a check made with a very light tint of Prussian blue. If a full seat-width contact around the entire circle of seated valve is not shown, the angles do not match. It will then be necessary to redress the valve seat grinding stones, changing the angle sufficiently to correct the error. The correction should be made on the valve seat, and not on the valve. No more material should be removed from the valve face than is necessary to true it up and remove the burned or pitted portion. New valves should not be refaced, but should be checked for true ness. When a satisfactory match of valve seat and valve face angles has been obtained, the adjustment of both the valve refacer and the seat grinder should be locked in position, in order to eliminate this trial-by-error method on additional valves having the same angle.
No clearance
Clearance
Fig. 18
(see "At! in Fig. 18). To check cap clearance with valve removed from engine, install keys and valve spring retainer under shoulder of valve stem. Position clearance gauge on valve stem. Place cap on plunger pin pressing down firmly. Turn spindle of gauge and check ,read ing as outlined in: foregoing (Fig. 19).
Valve Seats
The primary purpose of a valve seat is to seal the combustion chamber against pressure losses and to provide a path to dissipate the heat accumulated in the valve head so as to prevent burning of the seat and warping of the head. The location of the valve seat on the valve face and its width controls the amount of valve head that protrudes into the combustion cham ber. It is obvious that the greater the exposure within the combustion chamber. the higher the valve temperature; or in other words, the more heat it will collect. High valve temperatures and poor heat dissipation also produce exces sive valve stem temperatures and hasten the accumulation of carbon on the stem, causing them to stick in the guides.
Fig, 19 - Checking cap clearance with valve removed. Repair of Cylinder Head
1. If cylinder head has to be resurfaced, re
move only enough material to true-up
surface.
If any valve guide shows excessive clear ance or out-of-round-condition, press guide from head. Install new guide. and press into head until approximately 1-1116" remains above the top surface of the head. Check valve guides after installation to .OOZ" to .004" for exhaust and .0015" to .0035 /1 on intake with "Go and No-Goll gauge. Ream valve guides to .437" after assembly in cylinder head (Fig. lZ). 3. If inspection indicates necessity, replace valve seat.
Z.
Valve Seat Widths

In general, the width of exhaust seat should range between the average and maximum spe cifications and the intake seats between the minimum and average specifications. The in take seats may be narrower than the exhaust

because they are usually larger in diameter, thus providing a total seat area approximately equal to smaller exhaust valve with the wider seat. Also the less severe heat conditions do not require as large a seat area for heat dis sipation purposes. Figure 9 illustrates re commended valve seats to be obtained. There are also objections to an excessively wide seat, a few of which are as follows:
4. Place valves in cylinder head. Place a thin coat of Prussian blue on each valve face, and tap valve lightly to its seat. NOTE: This is merely for test and proof of results of refacing and reseating opera tions. A poor grinding job cannot be cor rected by valve lapping. 5. Inspect each valve coated with blue for seat position. The seat should be at the approximate center of the valve face. 3/32"-' 1 / 8" (exhaust) with the widest seat prefer abl~. Intake seat should be 5/64"-7164 11
1. In city or light delivery service, a wide seat collects carbon and particles of dirt that will produce variations or loss of compression, resulting in poor idle and possible loss of general performance and economy.
2. A wide seat in severe service operating in the presence of dirt or an excess of carbon will produce a badly pitted seat which may be just as detrimental to valve life as a too narrow seat Under these conditions, a seat widthto the minimum limit wouldpos sibly be better; however, the source of trouble which is the dirt and excessive carbon should be eliminated, making it possible to retain the wider seat.
Valve Assembly
1. Wipe valve faces and valve seats with a cleaning solvent to remove all dirt or for eign material. Coat valve stems and valve faces with oil, and install valves in same seats to which they were checked. NOTE: Check exhaust valve rotating mechanism to assure proper clearance between valve stem and cap before installing valves. 2. Install inner and outer valve springs. In stall retainers. Compress valve springs with a valve spring compressor, and install valve spring retainer locks. Be sure that retainers and locks are correctly seated. Recheck exhaust valve cap clearance.
Valve Seat Inserts

Necessity for replacing valve seat inserts should be very rare; however, if a replace ment is made it is important that new inserts be peened securely in place, using either in sert peening tool or a dull-pointed chisel, 1/4" wide, to peen cylinder head metal over outer edge of valve seat" insert. Valve available. seat insert instaUing tools are
Engine Disassembly - Continued

When overhauling engine with head and pan removed, the following procedures are re commended: 1. Remove fan drive pulley nut and washer from end of crankshaft. Install puller and remove crankshaft fan drive pulley and damper assembly from crankshaft. 2. Remove nuts and capscrews from engine gear case cover, remove gear case cover. Remove crankshaft oil slinger from end of shaft. Push twelve tappets up into retain ing clips to permit camshaft removal. Remove nut from end of camshaft and re move camshaft gear with puller. NOTE: Camshaft may be removed without remov ing timing gear, by removing thrust plate retaine r sc rews. 3. Remove capscrews from camshaft retainer thrust flange plate. Remove camshaft. Remove two capscrews holding the gear case cover plate to block; remove plate and gasket. Remove crankshaft timing gear, using a gear puller. (NOTE: Lubri cate puller screw to prevent damage to screw threads.)
Valve seat inserts supplied for service are standard size and .030 11 oversize which permits a tight fit in cylinder head.
Repair of Valves
1. True-up the ends of valve stem against fac~ of g rinde r. NOTE: Thi s refacing operation applies to the intake valves, how ever, in the case of the exhaust valves, where slow rotating valve mechanism is used, refacing of valve stems is not neces sary except when clearance adjustment is made. See under IIROTATING EXHAUST VALVE MECHANISM". Remove only enough material to true the surface. 2. Reface exhaust valves to 45 0 The valve face and valve seat angle must be identical. 3. Reface intake valves to seat being the same. 15 0 with valve
Fig. 20
4. Each connecting rod is numbered as to its position in the engine and these numbers are located on the camshaft side of the en gine. Remove self-locking capscrews from connecting-rod cap and remove cap (Fig. 2.1). Push connecting-rod and piston assembly toward top of block. Lift piston and connecting-rod assembly from top of cylinder block. Replace cap on connecting rod. Remove the remaining pistons, fol lowing the same procedure.
Fig. 22
Fig. 23
Fig. 21
5. The crankshaft bearing caps are numbered to identify their position and they must be reinstalled in their respective positions. Remove rear oil seal retainer (Fig. 2.2.), Remove all crankshaft main bearing caps (Fig. 2.3). Remove twelve capscrews from clutch and remove clutch. Remove six self-locking bolts from flywheel. Install two 1/2" N.C, bolts, 2" long, in threaded holes in flywheel and force flywheel from c rankshaft flange dowels (Fig 24). Remove flywheel from housing. Remove six bolts from, engine flywheel housing (Fig. 25), Tap housing with a soft hammer to knock it from dowels. Remove housing from crankcase. Lift crankshaft straight up and out of cylinder block and place in vise with
Fig. 21+
ENGmES Super Red Diamond Section C Page 11
spring guide, and a seal carbon washer. The parts are held in place in the impeller by a snap ring. The impeller and seal assembly is pressed onto the pump shaft (press fit of .002" to .0035").

(Complete illustrated procedure for Water
Pump Servicing is given in Shop Talk No. 14)
1. Remove four capscrews and lockwashers holding fan to pulley. Remove fan blade assembly from pulley. Remove water pump from front end of cylinder head. 2. Remove nut and flat washer holding pulley to water pump shaft. Remove pulley from water pump shaft with puller. 3. Remove five capscrews from cover plate. Remove plate and gasket from pump body. 4. Remove snap ring from in front of the water pump shaft frontbearing. Supporting water pump on arbor press, push shaft and bearing as an assembly out of impeller from the rear. 5. Support the shaft and bearing, assembly on an arbor press, force shaft out of bearing. spacer, and slinger, pressing shaft toward rear bearing. Be careful not to lose the two half-moon lock rings from under the slinger. 6. Remove snap ring from groove in the front of impeller, and lift out the seal parts from the impeller.
Fig.25
soft jaws. NOTE: Self-locking bolts may be used instead of bolts requiring locking wires. The self-locking bolts, identifiable by the depression in their heads, require no locking wires. 6. Remove fuel pump, starter, oil pressure regulator valve assembly, distributor, generator, oil gauge, and ignition coil.

See sectional view of RD Engine water pump (Fig. 26). The water pump assembly is composed of a body and cover plate which house a ball-bearing mounted pump shaft and impel ler. The rear and front bearings are pressed onto the shaft and are separated by a spacer. A slingeris held in placeby two halflock rings. The shaft assembly with its two bearings is h~ld in place in the housing by a retaining snap rmg. The fan pulley is pressed onto the shaft (press fit .0007 11 to .0018!!) and held in place by a nut and plain washer. The impeller seal assembly consists of a seal spring, seal clamp ring, flexible seal, seal

1. Following disassembly, wash all
rubber parts in cleaning solvent.
2. Examine seal parts for wear, corrosion, or damage, and replace with new parts as necessary. Examine the pump body seal seat surface. If face of surface is scored it must be resurfaced to prevent leakage: Inspect pump shaft bearing for wear or corrosion. If worn or corroded, replace bearings. Examine shaft for wear at ends, or for damaged threads at front end.
Impeller
Seal
washer Spring
Water Pump Repair

If water pump body seal seat is scored, pitted, or rough, it must be resurfaced. Use special water pump housing seat finishing tool and adapter.
Water Pump Assembly

Fig. 26.
..RINTED fN UNITED STAT'I'S 0,. AMERICA
1. Install rear bearing, spacer, and front bearing onto water pump shaft. Place
slinger in position behind rear bearing. Place two half-moon lock rings in groove in shaft, and press shaft into bearing and spacer from rear until rear bearing rests firmly against slinger and ring locks. 2. Place seal clamp ring, seal spring, seal spring guide, flexible seal and retainer, and carbon seal thrust washer into posi tion in impeller. Hold them in position while installing snap ring in impeller groove.
3. Install
water pump shaft and bearing assembly into body and hold in place by inse rting snap ring in groove in front of front bearing.
Fig. 28
2. To separate the two manifolds, remove the two outside bolts and nuts and two inside bolts and nuts frOln the center of mani folds. 3. The intake manifold is of one piece con struction. The exhaust manifold is of three piece construction (Fig 29).
4. Support water pump shaft at front end, press impeller and seal assembly onto rear end of water pump shaft. Press im peller only flush with end of shaft. 5. Place new gasketin positio:n on water pump body and install cover plate and four cap screws. 6. Place fan assembly in position on front of pulley, and install six capscrews and lock washers.

When disassembling and assembling the manifolds the following procedures are used: 1. After removing eight nuts, eight flat washers, four capscrews .and three bolts f rom exhaust flange, remove both intake and exhaust manifolds as a unit (Fig. 27). Remove two manifold pilot rings (Fig.28). NOTE: Let manifolds cool before starting above operations; this will help to prevent manifold warpage.
Fig. 29
Intake Manifold
1. The intake manifold consists of three out lets, each supplying fuel to two cylinders. Two studs are located on the top for car buretor mounting. 2. If vacuum is needed to operate any unit within the truck, a threaded inlet is pro vided in the manifold for such purposes.
Exhaust Manifold
The exhaust manifold consists of three parts and four outlets. The two end outlets re move burned gases from the No. I and No.6 cylinders, while the two center outlets remove burned gases from Nos. 2, 3, 4, and 5 cylin ders.
Manifold Inspection
. . ::..- ...7sf'1J:
;J;;A-22236
Fig. 27
Inspect intake and exhaust manifolds visu ally for cracks or breakage. Place manifolds

on surface plate and check for warpage. If cracked or broken, replace or weld. If slightly warped, true-up on surface grinder but replace if warpage is extreme.
PIN
KEY--------~~~111
Manifold Assembly
Place new gasket between the intake and exha ust manifolds and install four bolts and four nuts. Mount manifolds together loosely before installing on engine. This will assure proper alignment of the units with each other and with the engine cylinder head. NOTE: Do not elim inate the intake manifold aligning pilot rings. Tighten both manifolds to head. Tighten ex haust manifold expansion clamp bolts (Fig. 30), and replace with new seals if needed, and tighten intake to exhaust manifold bolts.
BODY----~
IDlER GEAR SHAFT
Fig. 30
Oil P ump Overhaul

(Complete illustrated procedure for Oil Pump
Overhaul is given in Shop Talk No. 28)
Special tool equipment is available for oil pump overhaul under SE-l499. Use of these tools will speed up the job and assure accurate work.
AJ0965
Fig. 3 I
shaft so as to apply pressure of press at bottom of slot, press oil pump drive shaft out of oil pump spiral gear. Remove Woodruff key from shaft. Remove oilpump body gear and oil pump drive shaft from oil pump body. 4. Press oil pump gear onto oil pump drive shaft far enough to reveal retainer ring. Remove ring from oil pump shaft. Press oil pump body gear from shaft and remove Woodruff key from shaft. Wash all parts in cleaning solvent.
Oil P ump Disassembly

See Sectional view of model RD engine oil pump (Fig. 31). 1. Remove cotter pin holding float to oil pump. Remove float from pump. 2. Remove six capscrews and lockwashers from oil pump b!=>dy cover and lift cover and gaskets from oil pump body.
Oil Pump Inspection

Check the following parts carefully: 1. Check the oil pump drive shaft for wear at points of contact with body. If wear is perceptible, the shaft must be replaced. Diameter of shaft is from .4985 to .4990 inches.
3. Lift out oil pump idler gear from idler gear shaft. After removing oil pump drive gear shaft guide from top of shaft, use small punch to drive out spiral gear pin from oil pump spiral gear. Using an adapt er collar which fits underneath the spiral gear, and an adapter with a tang which will fit down into the slot of the oil pump drive
PRINTEO IN UNITto:D STATES OF AMERtCA

4, Insert oil pump float in oil pump body, line up cotter pin holes, install new cotter pin, and fasten securely.
2. Check the oil pump body for warpage, dam age and wear. Replace if body is warped or cracked, or if shaft bore is worn so that clearance between shaft and bore is in excess of .OOSIT. Inspect all oilpump gears, and replace if weal' is perceptible.

REPAIR AND ASSEMBLY OF
SUB-ASSEMBLIES

Remove all old clean both inside steam or cleaning oil, sludge, scale, block. gasket ma terial from block, and outside of block with solvent. Remove all dirty and carbon from cylinder
Oil Pump Assembly

1. Press body gear onto oil pump drive shaft after placing new Woodruff key in slot of shaft. Press gear onto shaft far enough to permit installation of retainer ring in groove in oil pump. Press oil pump body gear down against ring.
2. Insert oil pump drive shalt and body gear into oil pump body. Install new Woodruff key in slot at top end of shaft. Install oil pump spiral gear, with gear hub down, onto drive shaft. Press spiral gear down onto shaft untill/32"clearance remains between gear hub and pump body when oil pump body gear is up against pump body. Using hole in spiral gear as guide, drill .1255" hole in shaft. Drive new spiral gear pin into place. Install a new guide on the end of the pump shaft, use guide installing tooL 3. Install idler gear on idler gear shaft. In stall gasket and oil pump body cover, and install four capscrews and lockwashers. Test oil pump body gear and play to cover by using a feeler gauge between oil pump spiral gear hub and oil pump body. End play must be from. 0025"-. 0055". If clear ance is in excess of. 0055", remove one gasket from cover. If clearance is less than .002", add one gasket between cover and body. Recheck end play after making any alterations. Insert oil pump into cyl inder block so that slot in top of shaft is o 30 angle to the side of the engine with the No.1 piston in firing order (Fig. 32).

1. Inspect cylinder walls for cracks,
Weld cracks or replace block, if necessary.
2. Check top surface for trueness with a straight-edge. Test by attempting to in sert a . 012" feeler gauge ribbon between the straight-edge and the cylinder block, If this is possible, either surface grind or replace the cylinder block.
3. Inspect camshaft bearings for damaged or scored condition, and inspect for wear. Replace if damaged or if worn beyond clearance limit of ,0035 11 , End play should be from ,001 11 to ,0035". Special tool eq uipment is a vailable for ins talla Hem of the prereamed camshaft bearings (Fig. 33).
4. Measure cylinder walls with an inside reading micrometer to determine taper, out-of -1' ound or worn condi tion. The meas urements must be made not only at top of the cylinder bore, just below ring groove, but at several places aroUI).d the inside circumference of the bore. Bore should be checked at the bottom, below ring wear surface, to determine the amount of taper. Re-sleeve if worn beyond ,008" clearance.
FRONT ..... - - - OF ENGINE 1
CYLiNDER HEAD COVER
l)
Bushing arbors
Oil PUMP SHAFT SLOT
CRANKCASE
AI0976
Camshaft bushings
Fig. 33
A.22149
Fig. 32

Cylinder Sleeve Fits
The fit oUhe cylinder sleeve in the crank case should be 100 to 200 lbs. hand push fit or approximately .0005" to .001" loose fit. This fit can be obtained by honing the cylinder bore sufficiently in the crankcase until the cylinder sleeve can be pushed all the way in by hand. Before installation of cylinder sleeve, the crankcase bores should be cleaned of all carbon and foreign matter. Installation of cylinder sleeves in the fore going manner will preclude to a large extent the necessity of excessive honing when fitting pistons to the cylinder sleeves. NOTE: New cylinder sleeves are rough honed and must be finish honed to size in the crankcase. NOTE: If cylinder water jacket shows an excessive amount of lime deposits. the cooling system cannot provide effective heat dissipation. Whenever the top of the sleeve flange goes below the top of the crankcase. a thin tag wire should be placed under the sleeve flange to raise it flush with the crankcase, or not to ex ceed .006" above the crankcase face. Cylinder wall surface finish is of utmost importance in piston and piston ring life and in oil consumption control. The best type surface is one hEwing characteristics midway between "smooth" and "highly polished". The resulting surface ofa boring or honing operation consists of numerous microscopic scratches or grooves which act as oil reservoirs or retainers of oil while the surface between the grooves provides a load-bearing surface. If the scratches are too deep and too close together, the surface is referred to as "rough" and will not provide adequate ring and piston contact area which results in fast wear. Should the finish be high ly polished or too "smooth", the scratches or grooves are shallow and will have insufficient oil-retaining capacity to provide adequate lu brication for the adjacent contact or load bearing area and will result in scuffing or scoring. It is therefore advantageous to strike a "happy medium" by removing only the sharp peaks of these microscopic ridges and in this way still reap the benefits of the oil-retaining grooves. This type of cylinder wall surface is obtained through exercise of care in finish ing operation and through proper use of equip ment. CAUTION: Extreme care ITIust be taken to assure that no abrasive remains in the engine after the finish honing operation. After engine has been reasseITIbled, it should be allowed to run-in for two or three hours ata fast idle (approximately 1200 r.p.ITI.).
PRINTED IN UNITED STA.TES OF ... MERICA
ENGlNES Super Red Diamond Section C Page 15

If camshaft bearing replacement is neces sary, remove and install new bushings with special camshaft bearing installation tool. No reaming is required. Fig. 33 illustrates the use of caITIshaft bearing ins talling tool.
Connecting Rod and Piston Disassembly

1.
Remove piston-pin retainers from each piston, and remove piston rings from pis ton ring grooves,
2, Heat piston in boiling water or piston heat er. Place piston in piston vise, and using pin-driving tool, drive piston pin from piston and connecting rod (Fig. 34), After piston pin is removed, lift piston from con necting rod.
....
.,.,."..-.,
~~
.' ":\s
..',.'. ,
--_:.>-;t".'!l/.,... .'"
"~.' "
( '.'J
"
"
A-22205
Fig. 3~ - Use suitable piston vise to hold piston and drive pin out with SE-126Q Piston Pin Driver. Use soft hammer.
3. Wash all parts in a cleaning solvent. CAUTION: Do not use a caustic solution for aluminuITI pistons. Clean the carbon hOITI piston ring grooves with a broken ring or ring gr oove cleaner. 4. Inspect connecting rods, caps, and bearing shells. All connecting-rod bearings and piston-pin bushings should be replaced at every ITIajor overhaul. Test rods for align ment. Rods only slightly ITIisaligned can be straightened with proper equipITIent. Badly twisted or bent connecting rods ITIust be replaced. 5. Inspect pistons for cracks, breakage, or scores. Check piston ring grooves and ring lands for wear, using a new piston ring ard feeler gauge. If clearance be tween ring and ring land exceeds .00SIt,
(total clearance) replace piston (see spec ifica tions). Pis tons which are s cored or damaged. must be replaced. 6. Inspect piston pins for wear. and if wear is perceptible, replace pins. Replace piston pins which show signs of corrosion or etching. 7. With properly fitting adapter (Fig. 35), press old piston-pin bushing from con necting rod. Place new piston-pin bushing in position, align oil hole in bushing with oil hole in connecting rod. (Fig. 36), install bushing with a .0035" to .0055" press fit. Burnish bushing into place in the connect ing rod (Fig. 37), then ream pin bushing to provide a hand-push fit.
Burnishing tool--....
Connecting rod
Press ram - - - - - - ' I.....
Fig. 37 - Burnish BUshing using SE-789.

, Connecting rod
Fig. 35 - Use SE-I036-6 to remove. bushing. Select proper hole in SE-I033 Support Plate.
Press ram - - - - - -...~. Adapter
Press plate ~
Connecting rod
~
Fig. 38 -Checking piston fit using feeler gauge ribbon. SE-I007 gauge set is avai lable.
(Fig. 35). Apply a tension pull on scale to the feeler ribbon and check clearance to specifica tions as outlined in the chart be low. Feeler Gauge Ribbon Checking Width . . . . . . . . Thickness . . . . . . . Tension on Scale (lb.). Desired Tension (lb.).
l/Z"
.003" 6-18 12
,,_JA.22457

8. With reamer, ream piston pin bosses ir. pis ton to provide a tight it of from .0000" to ,0002" with piston pin.
Connecting-Rod and Piston Assembly

1. With piston heated to approximately 200 0 F., support connecting rod in vise, push piston pin into piston bosses while piston is hot (Fig. 36). When assembling piston on rod, the slot in the piston skirt must be toward the camshaft side of the engine, which is the numbered side of the connecting rod. Install piston pin retainer in piston at each
Piston Fitting
When i tting pis tons in the cylinder sleeves. use a .003" feeler ribbon 1/2" wide between the piston and cylinder, 90 0 from the piston pin hole and in line with the thrustface of the piston
Fig.
14[----- Connecting
~O
- Checking ring gap.
rod
A.22466
Fig. 39
end of pin, making sure that retainers seat fully and with tension in grooves, Test connecting-rod and piston assembly on a connecting-rod aligner, and correct any mis -alignment, 2. Place piston and connecting rod in vise. Test each piston ring for proper gap by placing in cylinder and measuring gap with feeler gauge. Gap should be .016" to .026" (Fig. 40).
Piston ring
expander
Fig, ~I -Installing piston ring using Ring Instal ling Tool.
SE-II~9-6
Piston Ring Installation

1. Before installing rings in glazed cylinder bores, a surface-hone should be passed through the bores to remove the glaze and minor irregularities. This should only be done provided a thorough job of cleaning the grit and abrasives from the engine is performed after the honing operation. IMPORT ANT -- if the engine is not thor oughly cleaned after surface-honing, the benefits are more than offset by damage caused by the remaining grit and abrasives. 2. When installing piston rings in piston grooves, be careful not to distort rings. If possible, use a suitable piston ring ex pander tool (Fig. 41). Also check new piston rings in piston ring grooves for clearance between ring and ring lands. The correct ring clearance is shown in specifications.
3, Check crankshaft and flywheel dowels for damage and fit, and replace if worn or damaged. 4. Examine crankshaft timing gear teeth, and replace gear if .teeth are worn or damaged. NOTE: Replace timing gear on camshaft when replacing crankshaft gear. These gears are provided in matched sets. 5. Install Woodruff key in groove in crank shaft. Heat crankshaft gear in boiling water or pis ton heater. This will expand the gear enough to allow it to be tapped onto the crankshaft without the danger of damaging the gear. A special crankshaft gear in stalling tool is available.

1. Clean flywheel and ring gear with a clean ing solvent, remove all traces of oil and grease.
2. Inspect the flywheel ring gear. If any teeth are damaged, or if ring gear is loose on flywheel, the ring gear must be replaced. 3. Check the flywheel dowel holes and mount ing bolt holes for wear, also check for fly wheel having been loose.
Crankshaft Cleaning and Inspection

Wash and clean crankshaft with cleaning solvent or steam. 2. Inspect main-bearing and connecting-rod journals for wear. If journals show wear or out-of-round in excess of .003 11 , the shaft should be either reground and under size bearings installed, or replaced. Use micrometers for checking.
P'UNTEO IN UNITED STATES 0"- AMERtCA
1.

boss for fit and thread wear. If plug is loose or threads are damaged, repair threads or replace oil pan. 5. Inspect crankshaft pulley and vibration damper assembly for evidence of rubber coming loose from pulley flange plate, and inspect for wear. Replace damper assem bly if either condition is encountered. Do not submerge vibration damper assembly in hot cleaning solvents. Inspect crank shaftfan drive pulley for wear in hub bore. If inner diameter of bore is worn, scored, or Woodruff key way damaged, replace pulley. 6. Inspect engine gear case cover, and re place if cracked or broken. Remove old cover seal and install new seal. 7. Check each of twelve engine valve tappets for irregular wear, chipping, cracking or scores. Replace defective tappets. 8. Inspect engine flywheel housing for cracks or breakage and replace if damaged. In spect flywheel housing to crankcase pilot dowel holes for wear. If wear is evident, drill or ream the holes and install over size dowels. Also inspect dowels fo.r wear and replace if wear is evident. 9. Inspect all capscrews and nuts for thread wear or breakage, and repla.ce as neces sary. Use new lockwashers when reassem bling engine. 10. All gaskets and oil seals must be replaced at each overhaul or major repair.
4. To replace flywheel ring gear, heat gear

with torch, and remove from flywheel with a hammer and drift. Heat new ring gear with torch, heating evenly all the way around. While the ring gear is hot, install gear on flywheel and allow it to cool.
5. Check pilot bearing in flywheel for wear

or damage and replace if needed.
6. Install flywheel on crankshaft. Install six

self-locking capscrews, drive dowel pins through flywheel to crankshaft. Tighten to 155 foot-pounds.

1. Wash camshaft in cleaning solvent, brush
ing to facilitate removal of all sludge or carbon deposits. 2. Inspect camshaft journals for wear or out-of-round. signs of
3. Inspect oil pump drive gear in center of shaft. If teeth are worn or damaged, the camshaft must be replaced, as the gear is integral with shaft. 4. Inspect camshaft lobes. If worn, chipped, or scored, replace the camshaft. 5. Inspect camshaft gear, and replace if wear is evident or gear teeth are nicked or otherwise damaged. NOTE: Timing gears are factory matched and are furnished in. sets. The gears should be replaced in sets. 6. To reassemble, install thrust flange over end of camshaft. Install Woodruff key in slot in shaft. Place camshaft gear in boil ing water or piston heater, and install over Woodruff key. Install camshaft nut and tighten to approximately 120 foot-pounds tension.
ASSEMBLY OF ENGINE
When all parts have been cleaned, in spected, and repaired, and necessary replace ment parts have been procured, .install engine cylinder block in engine overhaul stand for re assembly.

1. Cleaning miscellaneous engine parts. This
includes brackets, oil pan, engine case cover, flywheel housing, and other parts that were removed during disassembly of engine and were not covered by procedure. Wash in cleaning solvent or steam clean preliminary to inspection. 2. Check all twelve valve lifter or push rods for straightness by rolling on flat surface. Replace any that are bent or ha're loose ends.
Main-Bearing and Connecting-Rod Bearing

Installation
It is alignment model RD piloted in should be tion.
essential that main bearings be in with the crankshaft journals. The engines have the main bearing caps the crankcase (Fig. 42). All bolts carefully examined before installa
3. Inspect oil pan for cracks or deep bends, and straighten or weld. 4. Inspect oil pan drain plug and drain plug
BEARING CRUSH. Undersize preCIsIOn type bearing shells should be installed when, because of wear, bearing-to-crankshaft running clearances are to be reduced. Bearing caps must not be filed, lapped, or in any other manner reworked.
CRANKCASE - . - ----
To obtain proper bearing assembly with the correct "crush", Care must be taken when tightening the clamping bolts to make sure. they are drawn down alternately and evenly, usmg a tension wrench and tightening as specified. As a result of excessive bearing crush, due to reworking the caps, the rod or main bearing bore will possibly become distorted because more force is required to draw the cap and housing together. Rods, caps. or blocks mus t not be file~. lapped. or in any other manner reworked m order to reduce clearance. While such prac tice will make a tighter fit at top and bottom. it will result in an out-of-round bore and bear ing shell distortion. New bearing shells will have to be installed eventually and that is when additional trouble starts. In general, a visual inspection of the part ing faces of the rod or caps under a magnifying glass will provide sufficient proof of any attempt at reworking. Under the glass, the parting line surface of standard parts will show the manu facturing cutter tool marks and will not have a polished or extremely smooth appearance. On the other hand, reworked parts will have a polished surface and. if a file was used. will show the even pattern of the file teeth. Seri ousness ofthis condition is in direct proportion to the amount of reworking. BEARING SPREAD. Main and connecting rod bearings are designed with the "spread ll (width across the open ends) slightly greater than the diameter of the crankcase bore or con necting rod bore into which they are assembled .. For example, the width across the open ends of the engine connecting rod bearing not in place is approximately .025" more than when the
'i\\:-------f)'.f-l-.+TONGUE AND GROOVE METHOD OF BEARING CAP ALIGNMENT

A I 6096
Fig, ~2 Illustrates tongue and groove method of Behring Cap Alignment with crankcase.
Premature bearing failure will result from attempts to reduce journal-to-bearing running clearance by reworking of either bearing caps, bearings, or both, because such reworking will alter the engineered fit of the bearing shells in their bores and destroy the specifically de sired "crush". When installing precision type connecting rod or main bearings, it is important that the bearing shells fit tightly in the rod or case bore. To accomplish this, the bearing manu facturer makes the diameter at right angles to the parting line slightly larger than the actual diameter of the bore into which they are assem bled. When the assembly is drawn up tight, the bearing is compressed, assuring a good con tact between the bearing back and the bore. This increased diameter is referred to as bearing II crush" (Fig. 43).
DIFFERENCE BETWEEN DIAMETERS (A) AND (B) IS BEARING CRUSH (C)
C
O. D. OF BEARING WHEN INSTALLED IS THE SAME AS THE DIA. OF THE CRANKCASE OR CONN. ROD BORE DIAMETER (A) AT RIGHT ANGLES TO PARTING LINES GREATER THAN DIAMETER (B) WITH BEARING CAP DRAWN UP TIGHT DIAMETERS (A) AND (B) ARE EQUAL
A.16009
1oIfo-- "A" ----------------+1

BEFORE INSTALLATION - - - - - - - - - - - - - ..16088
SPREAD OF BEARING
Fig.
~3
Fi g.
Ij.~
bearing is in position in the rod. This condi tion causes the bearing to fit snugly in the rod bore and the bearing must be "snapped" or lightly forced into its s eat (Fig. 44). Rough handling in shipment, storage, or normal results of use in an engine, may cause the bearing spread to be increased or decrease.d from the specified width. Bearing spread should, therefore, be carefully measured and corrected as necessary before installation in an engine. Bearing spread can be safely adjusted as follows, although care and judgment should be exercised in the process:
1. Excessive spread. If measurement of spread indicates that distance "A" is ex cessive (s ee chartfor specifications), place bearing on a wood block and strike the side ligrtlyand squarely with a s oft mallet (Fig. 45. Recheck measurement and, if neces sary' continue until correct width (meas urement "A" in chart) is obtained.
2. Insufficient spread. 1 measurement of spread indicates insufficient spread, place bearing on wood block and s trike the back of the bearing lightlr and squarely with a soft mallet (Fig. 45. Recheck measure ment and, if necessary, continue until cor rect width (measurement "A" in chart) is obtained. Chart of Bearing Spread Dimensions.
RD Engine (Minimum)
Connecting-Rod Bearing Main Bearing 2.8985" 3.424"
DECREASING SPREAD
fiAt!
+ .025" + .025 11
INCREASING SPREAD
AI6095
F j g. 1t5
1. INSTALL
CRANKSHAFT AND MAIN BEARINGS. Clean all surfaces of crank shaft bearing journals and wipe clean the bearing bores in the cylinder block. Re move main bearing cap self-locking cap screws and main bearing cap. Wipe backs of cylinder block half of bearings, making sure that dirt and oil is removed. Place bearing shell halves in position in bore in cylinder block, making sure that bearing shells are fully seated, that oil holes in bearing shells line up with oil holes in cylinder block, and that locking tangs on bearings fit into recesses. Follow saIne procedure, place bearing shell cap halves in bearing caps. Place a film of engine oil on bearing shell surfaces and lift crank shaft to align itself in the bearings, and als 0 provide lubrication. Place bearing caps and bearing lower halves over crank shaft journals. Be sure bearing caps are properly installed with numbers to cam shaft.
2. In order that an accurate measurement can be made to check all bearing clear ances, a material similar to "plastigage" or "virgin lead" can be used.
3.
Use the following instructions when using "plastigage": (a) Remove oil from bearing cap insert and exposed half of crankshaft journal. (b) Place a piece of llplastigage" the full width of the bearing insert. (c) Reinstall the bearing cap. Tighten the self-locking caps crews to approxi mately 105 foot-pounds. (d) Remove the bearing cap. The flattened plastic material will be found adhering to either the bearing shell or the crank shaft.
Fig. ij6 - Checking Behring Clearance

(e) To determine the bearing clearance,
compare the width of the flattened plastigage at its widest point with the graduations on the envelope (Fig. 46). The number within the graduation on the envelope indicates the clearance in thousandths of an inch. NOTE: Do not turn crankshaft during the above procedure.
Fig.
~7
bearing. End clearance should be from .004" to ,012".
6, INSTALL FLYWHEEL HOUSING.
4. When using the "virgin lead method" use

the following procedure:
(a) Virgin lead wire of approximately, 010 11

thickness should be used. If wire of .010" thickness is not available and thicker wire must be used, it must be rolled to approximately ,010" thick ness.
Place flywheel housing in position over two fly wheel housing to cylinder block dowels and tap into place with soft hammer. Install six caps crews and lockwashers in flywheel housing. If either block or flywheel hous ing is replaced, the flywheel housing will have to be aligned. with a dial indicator. When correctly aligned, run-out of bore should not exceed .005". NOTE: If pos sible, align flywheel housing while engine is in overhaul stand and with engine in vertical position (flywheel housing up).
(b) Remove one bearing cap,
Place 1/2" piece of virgin lead lengthwise on top of crankshaft bearing journal.
7. INSTALL
(c) Install cap and bearing shell half. In

s tall bearing cap bolts and tighten to 30 to 40 foot-pounds tension.
ENGINE FLYWHEEL. Place. engine flywheel and ring gear into position on dowels in crankshaft flange. Install six self-locking caps crews in flywheel and crankshaft flange, and tighten to a tension of approximately 155 foot-pounds. using a tension wrench.
(d) Rock the crankshaft back and forth two

or three times. Further tighten bolts to 60 to 70 foot-pounds and again rock the crankshaft two or three times. Tighten bolts to 105 foot-pounds and remove bearing cap.
8. INSTALL VALVE TAPPETS. Coat each of twelve valve tappets with heavy engine oil and install from crankcase side of en gine (Fig. 47). 9. INSTALL GEAR CASE COVER PLATE. Place plate and gasket at front end of en gine cylinder block. Install two caps crews and lockwash.ers. NOTE: To be sure that cover plate is in line with the gear case mounting bolts, which go through the cover plate, install or start three or four gear case bolts before tightening the two cover plate caps crews. Remove gear case bolts after tightening operation. 10. INSTALL CAMSHAFT AND GEAR. Coat camshaft with engine oil. Insert camshaft into front end of engine block, being care ful not to damage camshaft bearings. Be fore completely entering camshaft, rotate
(e) The virgin lead will nowbe compressed

exactly in accordance with the amount of bearing to c:;rankshaft clearance. Peel off flattened piece of virgin lead wire and measure with micrometer. Thickness of flattened piece of wire is exact amount of bearing clearance present. Repeat above operations on all bearings.
5. If clearance is not within .0013 11 to .0043",

either use undersize bearing, regrind shaft or replace shaft. Check crankshaft for end-play which is taken up by No.4 main
JlifUNTEO IN UNITO $TAT$ OF AMRICA
F j g, 1J9 Fig, 1J8

shaft until marked teeth on crankshaft gear and camshaft gear index (Fig. 48). Install two caps crews and lockwashers in camshaft thrust flange, working through large holes in camshaft gear. Rotate crankshaft and camshaft to determine that gears do not bind or interfere. Back-lash must be from .000" to .002" (.0015" pre ferred). 11. INSTALL GEAR COVER CASE. Place gasket in position on case cover. Place crankshaft oil slinger over end of crank s haft and ins tall Woodruff key for fan drive pulley in crankshaft. Place gear case cover in position. Install capscrews, new lockwashers, and. nuts. NOTE: Do not tighten gear case capscrews and bolts at this point.
12. INSTALL FAN DRIVE PULLEY AND VIBRATION DAMPER. Heat crankshaft fan drive pulley and vibration damper assembly in boiling water. When heated, quickly install assembly on crankshaft and install washer and fan drive pulley nut. Tighten nut with wrench of about 36" lever age. Tighten gear case caps crews and bolts. By tightening the gear case cover to the engine block after the drive pulley had been installed, the pulley has served to align the gear case cover.
Fig. 50
necting rod bore, being sure that oil hole aligns with oil hole in connecting rod and that locking tangs of bearing shell fit into recess, Clean connecting rod cap bearing bore and clean back of bearing (Fig, 50), Place bearing shell lower half in connect ing rod cap (Fig. 51), making sure that tang of bearing fits into recess in cap. (NOTE: See instructions under "MainBear ing and Connecting-Rod Bearing Installa tion.") 3, Coat bearing surfaces with oil. Pull con necting rod into position on crankshaft journal and install connecting-rod cap and bearing. NOTE: Bearing cap must only be installed on connecting rod one way, with both con necting rod number and bearing cap number to camshaft side. Install two self-locking caps crews and tighten to 80 foot-pounds, use tension wrench,

1. Install one connecting-rod and piston as s embly down through top of cylinder block having slotin piston towards camshaft side of engine. Pistons are also marked with an arrow indicating front of engine. Use a pistonring compressor sleeve to compress piston rings and thus avoid possible ring damage (Fig. 49). 2. Wipe bore of connecting rod free of oil and dirt. Place bearing shell upper half in con-
Bearing tang _---lao
A-2ISTB
Fig. 52

A-22465
1. INSTALL HEAD. Place gasket on cylinder

block and align bolt holes. Place cylinder head on crankcase, being careful not to damage or shift gasket position. Loosely ins tall all cylinder -head bolts and flat washers, omitting rocker arm oil feeding bolt. Tighten alternately and evenly in sequence to 105 foot-pounds. 2. INSTALL VALVE ROCKER ARM ASSEM BLY. Insert twelve valve lifter rods in cylinder head, make sure they enter the valve tappet. Lift the valve rocker-arm assembly into position on cylinder head. Install rocker-arm oil feeding bolt six 3/8" SAE nuts on hole-down bracket studs, and six hold-down bracket capscrews. Be sure to place stud with the oil hole, in the left third from rear, cylinder-head bolt hole and tighten to 105 foot-pounds. Re tighten cylinder head after engine has been operated for a short period. Install oil pan making sure all gasket joints are leak proof. See Fig. 53).
Fig. 51
4. To check connecting-rod bearing to crank shaft clearance, follow procedure given for "plastigage" or "virgin lead" test. Speci fied connecting rod bearing to crankshaft clearance is from .0012" to .0037". Do not attempt to file connecting rods or bearing caps. Follow procedure outlined in steps above for remaining connecting rods and pistons. INSTALL CLUTCH. Install clutch driven disc against flywheel so that the long por tion of the hub is toward the rear. Place clutch in position on flywheel over clutch driven disc. Locate clutch so that arrow or inspection mark (usually a dab of white paint) on flange of clutch backing plate or cover is as near as possible to the letter "L" on the flywheel, and install two or three mounting capscrews and lockwashers loosely. Insert a clutch aligning arbor, if available, or a transmission main drive gear shaft, through clutch driven disc hub spline and into clutch pilot bearings. Hold clutch driven disc in position while com pleting installation of twelve mounting cap screws and lockwashers in flange of clutch backing plate or cover. Tighten all twelve capscrews alternately, evenly and securely. Remove three retaining capscrews and flat washers which were installed to hold clutch compressed (Fig. 52). NOTE: Clutch will not operate properly unless these retain ing caps crews are removed. INSTALL VALVE LIFTER ROD COVER. Install new gasket over opening at left hand side of engine block. Install valve lifter rod cover and six caps crews and copper washers.
PRINTED IN UNITED STATES 0'- AMERICA
5.
6,
7.
Fig. 53

oil gauge, and thermostat. Tighten fan belt sufficiently to secure 1/211 depression on belt midway between generator pulley and fan pulley. Install oilpan making sure that gaskets are in place when tightening the pan. 8, FILL ENGINE WITH OIL. After making certain that oil drain plug is securely in stalled, fill crankcase with oil. After engine has been installed and placed in operation, again recheck oil level and add as necessary to bring oil level to full mark. 9, INSTALL CYLINDER HEAD COVER. If engine is not to be installed at this time, install new cylinder-head cover gasket and install cylinder-head cover. Install four flat washers and four nuts on cover.
3. ADJUSTING VALVES, To adjust valve stem to valve rocker arm clearance cor rectly, each cylinder must be on top dead center on its compression stroke at the time of adjustment of valves for that cyl inder. To determine the correct position, turn the engine crankshaft until No.1 piston is at top dead center on compression stroke and the ignition timing mark on the crank shaft pulley in line with the pointer on the timing gear cas e. Adjus t clearance on each valve of No.1 cylinder to .018 11 to .020" by using a feeler gauge between valve stem and valve rocker arm and turn rocker arm adjus ting s crew out of rocker arm until cLearance is obtained. Tighten adjusting screw lock nut and recheck clearance. (NOTE: Valve clearance should be re checked with engine at normal operating temperature. ) 4. Turn crankshaft one-third revolution and adjust clearance on No.5 valves. Working in firing order sequence, continue to set valves of each of the remaining cylinders, turning crankshaft one-third turn after each valve adjustment. 5. INSTALL WATER PUMP. Place water pump gasket in position, at water pump opening in front of cylinder head (Fig. 54). Install water pump and fan and install three caps crews and lockwashers in pump and cylinder block.
ENGINE MOUNTINGS
Figs. 55 and 56 illustrate engine front and rear mountings.
Gear case cover
Retainer
Bolt
A-15419
Fig. 55
Side rail Support bracket cap
Support bracket
trunnion
Bell housing
Rubber insulator
~
Fig.
5~ -
--~--~/~
/.
Installing Water Pump
6. INSTALL OIL FILTER. Place oil filter and new gasket in place on cylinder block. Install four capscrews and lockwashers in oil filter base. (NOTE: Be sure filter assembly is thoroughly cleaned and a new cartridge is installed before replacement on engine.) 7. INSTALL ACCESSORIES. Install carbu retor, generator, distributor and connect ing wires, starter, fuel pump, ignition coil,
Rear support bracket
A-15420
Fig, 56

Handle
ENGIN"ES Super Red Diamond Section C Page 25
Gasket ---.:tIOo.!._~_.J Cover Gasket ----lIl!"~IIIC..// Pressure valve

Lock pin
I
Center tube Cartridge Oil return channel Shell
t t
,
0 0
'\
~I
I
Cartridge
Center tube Oil outlet
\
Oil outlet
f
~
.;
Shell
Cartridge_-l~=;#i=:d---1~
spacer Plate ---:;...:;:j",~~"""'''-'-I

Gaskelt----~~~~~--~I
~+--+-Il-o:-.
Relief valve
A-22636
Fig. 57 - Deluxe Oil Fi Iter
OIL FILTER (DELUXE)

1. The DeLuxe oil filter is used on the RD engine s and incorporates a removable sump (Fig. 57). Water, grit, rneta1 particles, sludge and other contarninants that settle out of the oil are held in the surnp away from the cartridge. When the cartridge is changed the cartridge and sump quickly and easily lift out as a single unit. Change filter cartridge and clean sump at regularly es tablished periods; according to operating conditions.
Fig. 58 - Mi chiana Oi I Fi Iter

center tube through the oil filter base. Pressure at which the oil is discharged into the filter elernent is controlled by the pressure valve at the top of the center tube. The orifice at the bottom. of the center tube contains a 7/64" hole. 2. Oil leaves the tube at the center of the filter elem.ent and flows through the ele ment toward the ends. The filtered oil re turns to the oil pan through the oil filter base. The filter elem.ent or cartridge should be replaced when the oil appears sm.oky or black, The elernent is replaced by un screwing handle at the top of filter and lifting off cover, The old filter elem.ent can then be removed and a new one in s taIled.
2.
3.
OIL FILTER (MICHIANA)

1.
The Michiana oil filter is used on the RD engines (Fig. 58). Oil from. the engine is delivered by the oil purn.p into the filter
PRINTED IN UNITEO sr"'T'E$ OF AMERICA

CRANKSHAFT PULLEY TIMING MARKS
The ignition timing mark and the timing pointer is located on the front of the engine at the crankshaft pulley. To assure efficient operation of the engine, the timing should be checked with a timing light, and the timing mark and pointer should be in register as indicated for the best engine performance. Two marks are located on the crankshaft pul ley. One marked with an "Oil indicates top d ad center (T.D.C.) and the other mark shows 5 5 before top dead center (T.D.C.)
4. Do not attempt to wash out the old filter element. Replace with a new one. 5. Remove drain plug in filter sump whenever a new elementis installed and drain sump. 6. Ifnew engine oil discolors too rapidly after the filter element has been replaced it may indicate that the pressure valve in the center tube is not functioning and the oil is not going through the element. Re move the complete filter unit from the en gine and wash the parts with cleaning solvent. 7. Avoid using a wrench on the filter cover handle. If the cover cannot be drawn down by hand tight enough to prevent oil leakage it is necessary to replace the gasket.
CRANKCASE VENTILATION
<1.
The RD engine has a crankcase ventilator metering valve ins talled at the oil filler pipe. The purpose of the crankcase venti lator metering valve, which is connected to the intake manifold by a vacuum line, is to control the amount of fumes and vapors drawn from the crankcase by the intake manifold vacuum. The operation of the crankcase ventilation system consists of drawing cleaned air into the engine and withdrawing the fumes from the crankcase. CRANKCASE VENTILATOR ME TERING VAL VE. To remove the ventilator meter ing valve disconnect the vacuum line lead ing to the intake manifold. Unscrew the ventilator metering valve unit from the oil filler pipe. To service, separate the two halves of the valve unit, and remove the weight. Clean all parts. When installing the ventilator metering valve on filler pipe, point arrow up. Screw unit into filler pipe. Connect vacuum line leading to the intake manifold (Fig. 59).
2.
Metering orifice Upper housing ''7'r--,,..,.A Small section of metering pin in orifice
Large section of metering pin in orifice restricts flow of air
Lower housing Position of weight with low manifold vacuum (below 3~ to 4!i inches mercury)
Weight Position of weight with high manifold vacuum (above 3!i to #2 inches mercury) A.23449
Fig. 59
L~LINE
FRAMES Index Page 1
FRAME GROUP
SECTION "A"
Page
F:rame alignment . . . . . . . . . . . . . . . . . . . . . . . . Checking frame alignment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Axle alignment with frame . . Frame
strai~htening
1
1
1
2
...
PRIN1'O IN UNITEO $TATf:S OF AMERICA
FRAMES
Section A Page 1
FRAMES
Frame Alignment
Any vehicle that has been in an accident which Inight result in a bent or sprung fraIne should have the fraIne and axle alignInent care fully checked. 3. Measure distance froIn center line to oppo site points Inarked over entire length of fraIne. MeasureInents should not vary Inore than 1/8" at any point. 4. Measuring diagonals, A-A, B-B, C-C, D-D will indicate point where InisalignInent oc curs. If diagonals in each pair check with 118", that part of fraIne included between points of IneasureInent Inay be considered in satisfactory alignInent. These diagonals should intersect within 1/8" of center line.
Checking Frame Alignment

A satisfactory Inethod of checking the fraIne and axle alignInent, particularly when a body and cab is on a chassis, is to Inark on a level floor all points at which IneasureInents are to be taken. Tack or ceInent pieces of paper to the floor directly under each point of Ineasure Inent on the chassis as indicated by the letter "K" in the various figures. The points of Ineas ureInent Inust be accurately Inarked in relation to the fraIne in order to obtain a satisfactory alignInent check. After each IneasureInent point has been carefully Inarked on the floor, proceed as fol lows: 1. Locate center line of chassis by Ineasuring front and rear end widths, using Inarks on floor. If fraIne widths check, draw center line on floor, full length of chas sis. If fraIne widths do not check, layout center line as follows: 2. Center line can be drawn through the inter section of anyone pair of equal diagonals (A-A, B-B, C-C, D-D) and center point of one end of fraIne or through points of inter s ection of any two pai r s of equal diagonals.
Axle Alignment with Frame

After deterInining that fraIne is properly aligned, the axle alignInent with the fraIne should be checked by cOInparing diagonals. DiInensions for side elevation of frame should be checked at the points indicated and should not vary Inore than 1/8".
Cutting, Reinforcing, Riveting and Welding

Whenever it is necessary to cut the fraIne, the side rail should be cut at an angle of 45 degrees. This Inethod distributes the cut and weld over a greater area than a cut Inade at right angles with the rail. ReinforceInents can be Inade with flat, channel, or angle stock. Because of difficulties encountered when inserting channel reinforce Inents into fraIne side rails, the use of angle reinforceInents is acceptable. Wherever pos sible the reinforcement should extend froIn the
K
K
//
H --~ ------ -1""" _-- K //---

,
"/
K
/
A/
/
"
"
"
./ ./
""- "/
/
""- "/
,, ,
'A, ,
/ /
""
"B
",
/
/
C C
" "
""-
K
A-22709
Fig. I - Frame and Axle Al ignment Checking Diagram.

FRAMES Section A Page 2
'~C=:::-')
L-150-FRAME ILLUSTRATED
A22i'10
Fig. 2 - Frame and Axle Alignment Checking Diagram.
front axle to slightly beyond the rear spring front mounting bracket as shown in illustration below. This. procedure, of course, may be impractical in some instances because of the position of attached units and existing cross members. The reinforcement thickness should not exceed that of the side rail to be reinforced. Whereverpossible,parts should be secure ly riveted together. Hot rivets are acceptable, as they can be more easily driven with hand tools. Cold rivets should only be used where tools of sufficient power to properly set the rivets are provided. Electric arc-welding is recommended for all frame welding. The heat of the weld is lo calized and burning of material is minimized when this method is used. In addition to thoroughly welding the cut in the side rail, the outside edges of the reinforce
ments should be welded to the frame after the reinforcements are riveted. All unused holes should be filled with welding material. Welding rod should be substantially the same material as that used in the frame. The diameter of the reinforcement rivets depends upon spacing and the number of rivets used. Generally, rivets should be from 50% to l0010 as heavy in diameter as the total thick ness of the plates to be riveted.
Frame Straightening
Use of heat is not recommended when straightening frames. Heat weakens structural characteristics of frame members and all straightening should be done cold. Frame mem bers which are bent or buckled sufficiently to show cracks or weakness after straightening, should be replaced, or reinforced.
Inverted "L" type frame reinforeeme~i
A-22'l2'l
Fig. 3
FUEL SYSTEM Index Page 1
FUEL SYSTEM GROUP

INDEX
Page
SPECIFICATIONS
Carburetor (Carter) . Carburetor (Holley) Fuel pumps . . . . . . . . . .
SECTION "A"
FUEL SYSTEM AND FUEL PUMPS
GENERAL:
Auxiliary electric pump installation. . . . Truck storage - preparation of fuel system. Vapor lock . . . . . . . . . . . . . . . . . . . . . . FUEL PUMPS:
Description and operation . . . . . . Final check . . . . . . . . . . . . . . . . . How to diagnose fuel pump trouble. Installation of fuel pump assembly . . . . Locating fuel pump trouble . . . . . . . . . . .
1, 2
1, 2
3
3
3
3
SECTION "B"
CARBURETOR - CARTER (MODEL YF)
Description .. Disassembly . , Illustrations Reassembly.. , .
. .. . ......
....
.....
1
3
1, 2
3,4
SECTION (fC"
CARBURETOR - CARTER (MODEL BBR-l)
Carburetor overhaul. Choke circuit. . Description... . . . . Float circuit. . . . . High-speed circuit. Low-speed circuit Pump circuit. . . . .
2
2
1
1
1
1, 2
SECTION "D"
CARBURETOR - HOLLEY (MODEL 852-FFG)
Accelerating pump. Description . . . . . . . . . Idle fuel system . . . . . Main fuel system . . . . . Power mixture supply .. ADJUSTMENTS AND SERVICE HINTS:
Accelerating pump . . . . Altitude operation . . . . . Economy complaints .. Failure to idle properly. Final adjustment . . . . . Float level . . . . . . . . . Governor - model 1174 . High-speed complaints Idling speed. . . . . . . . Main fuel . . . . . . . . . .
PRINTED IN UNITEO STATES 0,. AMERICA
2
1
1
2
2
4
3
22
4, 5, 6, 22
4
FUEL SYSTEM Index Page 2
L-LIl\iE MOTOR TRUCK SERVICE MAl\iUAL
FUEL SYSTEM GROUP-Cont'd

INDEX
SECTION "D"
CARBURETOR - HOLLEY (MODEL 852-FFG) Cont'd OVERHAUL - CARBURETOR AND GOVERNOR

Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Disassexnbly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Governor adjustxnent. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Inspection and assexnbly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
7 to 18
22
18 to 22
SECTION "E"
AIR CLEANERS
De sc ription. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Se rvicing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Oil capacity. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1
1
Q '"
~ @
'"
.".
Ell
SPECIFICATIONS COVERING HOLLEY CARBURETOR MODEL 1904-FS USED ON SD-220,240 AND BD-269 ENGINES FUEL SYSTEM SPECIFICATIONS
ENGINE MODELS CARBURETOR (HOLLEY) MODEL NUMBER . . . . . . . . . . . . . . . . . Float Level . . . . . . . . . . . . . .
Venturi . . . . . . . . . . . . . . . . . . Main Jet . . . . . . . . . . . . . . . . . Power Jet . . . . . . . . . . . . . . . . High Speed Bleed . . . . . . . . . . Main Well Bleed-Upper. . . . . . . . Main Well Bleed-Lower. . . . . Idle Well Restriction . . . . . . Idle Air Bleed . . . . . . . . . . . . . Idle Transfer Hole . . . . . . . . . . Idle Adjusting Screw . . . . . . . . .
Accelerator Pump Spring. . . . . . Accelerator Pump Link . . . . . . . SD-220 1904FS Use gauge (SE-1772-9MC-145) 1-5/16"
\0
i~
til
SD-240 1904FS
BD-269 1904FS
Use gauge (SE-1772-9 MC-145) 1-5/16" '70 (Std. Alt.)
" t
~
'f' :-
Use gauge (SE-1772-9MC-145) 1-5/16" '70 (Std. Alt.)
If? 3 (High Alt.)

.052-'55 DR. .031-'68 DR. .025-'72 DR. .025-'72 DR. .028-'70 DR. .055-'54 DR. . 0465-'56 DR. Adjust Screw to Obtain 350 to 400 R.P.M. 38R-452 (.035 Wire) 33R-207 .0293-#69 DR. .082 Yes
'69 (Std. Alt.)
1f?3 (High Alt.)

.043-'57 DR. . 031-'68 DR. .025-'72 DR . .025-'72 DR. . 028-'70 DR. .055-'54 DR. .0465-'56 DR. Adjust Screw to Obtain 350 to 400 R.P.M. 38R-452 (Wire) 33R-207 .0293-'69 DR. .082 Yes
1f?3 (High Alt.)

.0595-'53 DR.
.028-'70 DR. .025-'72 DR.
.025-'72 DR . .032-'67 DR. .0595-'53 DR.
.0465-#56 DR.
Adjust Screw to Obtain 350 to 400 R.P.M. 38R-452 (Wire) 33R-207
.0293-#69 DR.
Z [l"]
Ei:
:::0
{J)
Accelerator Jet . . . . . . . . . . . .
Fuel Seat . . . . . . . . . . . . . . . . Used With Governor . . . . . . . .
ITj
'tjPJ
.082 Yes
~t' ....
CflC
'U0O<
1lI1l1Cf1
(IQ
~CfI
;::t...,
(001:'1
.... ;~
:CDCl CD 1:>1
SPECIFICATIONS COVERING HOLLEY CARBURETOR MODEL 1904-H USED ON BD-282 ENGINE FUEL SYSTEM SPECIFICATIONS
ENGINE MODELS CARBURETOR (HOLLEY) MODEL NUMBER . . . . Float Level . . . . . . . . . . . . . . . . . . . . Venturi. . . . . . . . . . . . . . . . . . . . . . . . . . . Main Jet . . . . . . . . . . . . . . . . . . . . . . .
Power Jet . . . . . . . . . . . . . . . . . . . . . . . . High Speed Bleed . . . . . . . . . . . . . . . . . Main Well Bleed - Upper . . . . . . . . . . . . Main Well Bleed - Lower . . . . . . . . . . . . , . . Idle Well Restriction. . . . . , , , . . . , . . . Idle Air Bleed. , . . . . . , , , . . . . . . , , .. Idle Transfer Hole . . . . . . , , . . . . . . . . . Idle Discharge Hole . . . . . . . . . . . . . . Idle Adjusting Screw . . . , , . . . . , , . , , . , . . . Accelerator Pump Spring, , .. , . . . . . . . . . Accelerator Pump Link, . , , , .. , . . . Accelerator Jet. " . . . . , . . . . , . , , . . , Fuel Seat , , . , . . . . . . , . . , . . . , . Used With Governor . . . . . . . . . . .
--
tU~~
NSt<
III ~t-<
.... III
01-3
BD-282 (Not RC-Trucks) 1904H Use Gauge (SE-1772-9-MC-145) 1- 3/811 *72 (Std. Alt.)
173 (High Alt.) .050 11
;1:>1 a:::
Z [Tl
3:
.035-1165 DR.
.025-*72 DR.
~
:::c
~
~
.025-1172 DR.
.031-#68 DR.
.055-1154 DR.
.0465-#56 DR. .0465-#56 DR. Adjust Screw to Obtjiin 350 to 400 R.P.M. 3!3R-452 (.035 Wire) 33R-207
.033"
.082"
Yes
~
~
E~
'"
~
SPECIFICATIONS COVERING HOLLEY CARBURETOR MODEL 885 FFG USED ON RD-406 AND RD-450 ENGINES
FUEL SYSTEM SPECIFICATIONS
ENGINE MODELS CARBURETOR (HOLLEY) MODEL NUMBER. " . . . . . . . . . . . . . . . . . Float Level . . . . . . . . . . . . . . . . . . .
Venturi. . . . . . . . . . . . . . . . . . . . . .
Main Jets . . . . . . . . . . . . . . . . . . . . .
Idle Tubes . . . . . . . . . . . . . . . . . . . .
Fuel Inlet Needle Seat . . . . . . . . . . . .
Accelerator Pump Plunger Stroke . . . . Power Jet Economizer Valve Flange . . . . . . . . . . . . . . . . . . . . . .
Idle Adjusting Screws . . . . . . . . . . .
Main Well Bleed. . . . . . . . . . . . . . . .
Aspirating Hole . . . . . . . . . . . . . . .
Accelerating Jet. . . . . . . . . . . . .
Idle Air Bleed . . . . . . . . . . . . . . . . .
Well Tubes . . . . . . . . . . . . . . . . . . .
Idle Progression Hole . . . . . . . . . . . .
Idle Adjusting Hole . . . . . . . . . . . .
Accelerator Pump Spring. . . . . . .
Secondary Venturi . . . . . . . . . . . . .
RD-406
RD-450
~ :t
~
:g
:;
E
:;0
rn c
885 FFG
1/2" Below Top of Fuel Bowl
1-7/32"
#60 (Std. Alt.) *58 (High Alt.) 54 C.C. Per Min. (.025") .098" Adjustable *No. 25R-80A-43 1-1/4 SAE (Dual) 3/4 to 1-1/4 Turn Open .025" .043" .033" .0465" 3/32" 0.0. 4 Holes .028" #56 DR. - .0465" '56 DR. - .0465" .040" Wire 3/8" I.D. 2 *18 DR. .,. .1695"
885 FFG
1/2" Below Top of Fuel Bowl
1-1/4"
161 (Std. Alt.)
g
", g
~
'1:1
r;
~
..
159 (High Alt.)

54C.C. Per Min. (.025") .098" Adjustable *No. 25R-80A-58 1-1/4 SAE (Dual) 3/4 to 1-1/4 Turn Open .031" .067" .033" .0465"
3/32" 0.0. 6 Holes .040"
*56 DR. - .0465"
#56 DR. - .0465"
.040. 1 Wire 3/811 I.D. 2 #18 DR. - .1695 (Continued)
n >
C
Z
tr1
3::
::0
d
()
~
?::
U>
I'sj
~ct
I1txl
nt:-<
~C/)
...
'tin 0<
OQ ....
." Bowl Cover Plate Vent Holes . . . . . . .

Only last two digits of number appear on power jet.
I~C/)
t-i
l1txl
I.>J~!J;:
SPECIFICATIONS COVERING HOLLEY CARBURETOR MODEL 885 FFG USED ON RD-406 AND RD-450 ENGINES FUEL SYSTEM SPECIFICATIONS - Continued
-
OQ(1I .... (1Iotzl IIl-SI:"'

Cll
III '1:1 ,..
'l1C1lIz)
!!...: .... CIl

o .;
;tzl
ENGINE MODELS GOVERNOR (HOLLEy) . . . . . . . . . . . Governor Spring Color Marking . . . . Governor Spring Position in Housing .. Governor By-Pass Jet (Hole "A") . . . . Governor By-Pass Jet (Hole "B") . . . Maximum No-Load Speed. . . . . . . . . Governor Rotor Valve and Housing Assembly - IH Part Number . . . . . . .
RD-406
885 FFG
Yellow
'3 Perch Position
.028"
.052"
2950 R.P.M.
RD-450 885 FFG

Plain
'3 Perch Position .028" .052" 2800 R.P.M.
==
'.' r
s:
114510-R9l
1145l0-R91
() tr1
Air Cleaner Oil Capacity Specifications covering the "Hat" type air cleaner used in conjunction with the Holley 1904 Carburetor.
<
SD-220 ENGINE 2 pints
SD-240 ENGINE 2 pints
BD-269 ENGINE 2 pints
BD-282 ENGINE
2 pints
-_ __
.........
......
[;-"
C
--

SD-240
[1l
ENGINE MODELS FUEL PUMP (AC) Model mnnber . . . . . . . . . . . Type . . . . . . . . . . . . . . . . . . Operating pressure . . . . . . . .
SD-220
BD-269
RD-406
RD-450
Cont. R-6602
1539537 AF
{3t04_l/Z
lbs. at 3500 engine r.p.m.
1539537 AF 3 to 4-1/2 Ibs. at ,e 3500 r.p.m.
1539501 AT
3 to 4-1/2 Ibs. at 3500 engine r.p.m.
1539513
.. I;J " ..
1539513
"
1539513
..
1538259
o --l o :;0
:;0 7';
(J)
$:
. ..
'"
. .
'"
. .. ..
"
--l
4 to 5-1/4
FUEL PUMP (CARTER) Model number . . . . . . . . . . . . . Operating pressure . . . . . . .

-=-......-......-_4'-~
M-737S
{ 3 to 4-1/Z
_ _ L-.
M-737S 3 to 4-1/2 lbs. at 3500 engine r.p.m.
EXl12-78 3 to 4-1/2 Ibs. at 3500 engine r.p.m.
. .. . . . .. .. . .
.. .. .. 1;1 ..
. ..
. . .. ..
. ..
~
..
"
. .. . . ..
.. . .. .. .. .. .. .
. .. .. .. .. . .. . .. . .. .. . . . . .. ..
..
"
..
. .. ..
..
.
.. .. ..
.. .. .. .. .. . . . .. ..
. . .. . .. .. .. . .
n [1l
$:
<
:P :P
C
z
r
"cJ M
enG
"'1
'1:l~en
~ l' .... en ...... ><: ....
ooOM
..... 111;:::.,
Pl:=;'>-1
11> ::I !::"
'l:jUl'Tj
()QgM
~:::;t:"'
N ...
III '"0
(") Ul
~o-<

ENGINE MODELS CARBURETOR (CARTER) Model nUITlber Float level Flange, . Venturi. , Main jet. Idle jet . . Accelerating jet. Main air bleed. Fuel valve seat Metering rod . . Idle adjustment Used with governor. SD-ZZO YF-735-S Z5/64" (! 1/64") 1-1/4 SAE 1-5/16 11 .104 .OZ76 ,OZ5 .034 .076 No. 75-693 3/4 to 1-3/4 turns open yes SD-240 YS-736-S 7/16" (.:!:.1/64") 1-1/4 SAE 1-5/16 11 .1015 ,0292 ,025 ,034 ,081 No. 75-688 3/4 to 1-3/4 turns open yes
o
(II
.... Ul
I-j
::J M
;g:
fT1
3:
o -; o :;:0
-;
:;:0
n
ENGINE MODEL CARBURETOR (CARTER) Model nutnber Float level Flange . . Venturi. . Main jet. Idle tube. Accelerating pUITlp jet. Step-up jet . , Fuel valve seat . . . Idle adjus tment , , . Used with governor. BD-269 BBRI-617SA 5/64" (.:!:.1/64") 1-1/4 SAE 1-5/16" 298 C.C, .031
.0315
.0374
.086
1/2 to 1-1/2 turns open
yes
7':
(f)
[T1
:;:0
< n fT1
3:
;p,
z c ;p,
ENGINE MODELS CARBURETOR (HOLLEY) Model number Float level Venturi. . Main jets. Idle tubes. ..... . Bleeder plug or button (in nozzle bar) . . . .. Fuel inlet needle seat . . . Accelerator pump plunger stroke . . . . . . . . . Power jet economizer valve . . . . . . . . . Flange . . . . . . . . Idle adjusting screws GOVERNOR (HOLLEY) color RD-372 AA-IG 1-1
1- ,
RD-406
852FFG
I 1/4"
1-3/16 11
.063
64 C.C. per min.
.234
.098
adjustable
25R-72A-49
1-1/4 SAE (dual)
3/4 to 1 turn open
'~No.
RD-450
852FFG
1-1/4"
1-3/16"
.061
64 C.C. per min.
.234
.098
adjustable
*No. 25R-72A-66
1-1/4 SAE (dual)
3/4 to 1 turn open
.059 88 C.C. per min. .175 .098 adjustable

No. 25R-67A
1-1/4 SAE
3/4 to 1 turn open
(Tl
d :::0
:::0 C
~
7':
(T]
en
:::0
brown
........
..
..
'"
position
.....
.........
. ........
< n
(T]
in housing. Governor by-pass jet

(hole "A") . . . . .
Governor by-pass jet
(hole "B") . . . . . . Maximum no-load speed Governor rotor valve and housing assembly-IH part number . . . . . . .
.. .. . . ..
.025
.047
2950 r.p.m.
54784-R91
.......
..........
.........
2925 r.p.m. 54784-R91 2750 r.p.m. 54784-R91 of number appear on powe r jet.
r
'Oc: M
(1)
* Only
last two
(Il'rJ
r'l t' .....
~(Il
'tlr'l'-<
>ll>ll(ll
(1)
()Q
::r.1-cl
1JJt!l:S:
gM
FUEL SYSTEM Section A Page I
FUEL SYSTEM-GENERAL
VAPOR LOCK The Service Parts Department has avail able an electric fuel pump for use on trucks which have given trouble with vapor lock, but they cannot furnish material other than shown in Fig. 1, because the installation will have to conform to individual requirements.
(a) Heat conducted from crankcase and

camshaft.
(b) Heatreceivedfrom hot oil splashed in

to pump body for lubricating purposes. (c) Radiated heat from exhaust manifold. (d) Heat received from under hood air. It is for these reasons that the electric fuel pump is mounted on the outside of the frame rail. The fuel line from the fuel tank to the reg ular mechanical pump is under a depression or more commonly known as suction which lowers the vaporizing or boiling point of a liquid. This makes it particularly bad to have it located close to the exhaust system. By locating the electric fuel pump close to the fuel tank a greater percentage of the system is under pressure, which increases the vaporizing or boiling temperature of the gasoline. WHEN AND WHY OF VAPOR LOCK Vapor lock occurs in hot weather with a hot engine when the fuel requirements are at mlmmum, such as idling after a hard run. When the maximum amount of fuel is again re quired, the fuel pump must first expell the va por during which time the following cycle is being established: (a) Reduced engine speed because of lack of fuel. (b) Reduced fuel pump speed with propor tional loss of pumping ability. (c) Increased fuel temperatures and re sultant increase in vapor formation resulting in reduced fuel delivery and further reduction of engine speed. The continuation ofthe cycle will1.4ltimately result in the complete cessation of gasoline de livery. TYPE OF FUEL - VAPOR LOCK The use of a highly volatile gasoline such as furnished in ItWinter" weather will produce vapor lock under conditions where a less vola tile or ItSurn.rnerltgasoline would be satisfactory. HOW TO DIAGNOSE VAPOR LOCK A vapor lock in the system permits the gasoline level in the float bowl to become low or even dry, causing a lean mixture, which is evidenced by the following operating character istics: (a) Lack of power on full throttle or soft ness and flat spots on part throttle op eration. (b) Stalling on idle when engine is hot. (c) Inability to start a hot engine.
Eledric fuel pump swit,h
~
~
T() coil side of igniti,," ,witch
'!!
II
Ii I!
I: I:
~I!,--[' ~~
H
I
Carburetor
~i
Mechanical ruel
"
Fig. I
INSTALLATION - ELECTRIC FUEL PUMP Fig. 1 illustrates a hook-up that is adapt able to any type of fuel system. The location of the fuel line from the elect ric pump should be on the outside of the frame rail opposite the exhaust system and if neces sary carried across the front cross member to the car bur etor . Considerable freedom can be exercised in locating the lines, always keeping in mind that they should be away from the exhaust system and not exposed to hazards that will result in their being damaged. The use of loom is rec ommended where protection from radiated heat is required. Should the electric pump be located where it may be damaged from stones, etc., a simple shield can be readily installed to supply the necessary protection. The following discussion on vapor lock is for the purpose of providing necessary infor mation to diagnose and get a solution to the problem: WHAT IS VAPOR LOCK? When a section of the fuel system becomes filled with gasoline vapor causing either partial or total disruption of fuel service to the car buretor, it is said to be vapor-locked. PRINCIPAL SOURCES OF HEAT - VAPOR LOCK The fuel pump is generally the part of the fuel system where the greatest rise in fuel temperature occurs because of heat derived from the following sources:
PRINTED IN UNITED STA.TES
or
AfoItRICA
FUEL SYSTEM Section A Page 2

1. Completely drain the fuel tank. 2. Run engine until all fuel is consumed in carburetor. 3. Remove plug from carburetor under main jet assembly to complete drain ing. 4. Empty sediment bowl at fuel pump. The possible affected parts in the fuel pump are the check valves and the filtering screen or filtering element. To determine the condition of the check valves, remove the caps from over the valves and test for freedom of action. The filtering screen, if in a gummed con dition, should be replaced and the sediment bowl cleaned. If there is doubt as to the condition of the carburetor, it is suggested that a one-quart mixture of 50-50 CP acetone and gasoline be burned through the carburetor at fast idle from a closed container attached direct to the car buretor - not through the fuel pump because of the detrimental effect of acetone on fuel pump diaphragms. This will serve to remove a large amount of the gum providing that it has not be come hard and varnishlike. If the results are not satisfactory the carburetor must be removed and all jets and carburetor valves replaced.
PROPER USE OF ELECTRIC FUEL PUMP FOR VAPOR LOCK

When the firs t indications of vapor lock are observed, the electric pump should be brought into operation and upon regaining thelostengine speed, should be shut off, thus giving the s tand ard mechanical pump an opportunity to rid the regular fuel system of vapor. This method of operation may have to be repeated several times before the mechanical pump will supply suffi cient fuel, after which the use of the electric pump is not required; however. in stubborn cas es continous operation may be necessary. It should be noted that II shut off" valves are not shown on the sketch as it is desired tomake the auxiliary system as flexible as possible to accomodate either continous or intermittent operation, making it unnecessary to stop the engine. NOTE: If the electric pump is not req uired regularly, it should be operated every few days to preven t the stagnant gas oline from forming gum.
TRUCK STORAGE - PREPARATION OF FUEL SYSTEM

When placing trucks in storage remove all fuel from the fuel sys tem. If fuel is not entirely removed, a gumlike subs tance will be deposited on all parts contacted by the fuel, and will seri ously affect operation of the carburetor and fuel pump. All standard grades of gasoline have a small gum content, which is not sufficient to cause any trouble under ordinary conditions. However, when allowed to stand for a period of two or more weeks, the gum will increase to a point where a deposit is formed on the surfaces which it contacts. This deposit, when dry, has a hard, varnishlike appearance. Gum deposits may completely alter cali bration of the carburetor for it will partially or completely plug the jets or cause the power jet valve and the accelerating pump to stick. Gum depos i ts in the fuel pump will caus e the fuel filter to become clogged or the check valves to stick. IMPORTANT: It is well to emphasize the E...ossibilities that can develop because of gum film in carburetor jets. A thin film of gum (assume .002" thick) is transparent and would escape casual inspection; but this thickness of film represents a .004" size, and should one or all jets be affected would be a lean-mixture ratio that would be det rimental to the engine as well as performance for it would contribute to sticking and burning of valves because of gum accumulation O'n the stems. The condition would also be a contrib uting cause of premature spark plug failures. Gum is not soluble in gasoline, therefore any reduction in the capacity of the jets will be per petuated almost indefinitely. The best knownmmean~ of preventing gum formation in trucks that are to be placed in storage or allgwed to stand idle for a period of two or more weeks is to thoroughly condition the fuel system as follows:
FUEL PUMPS
DESCRIPTION The fuel pump is installed on the engine between the fuel tank and the carburetor. The suction side of the pump is connected to the fuel tank and the discharge side to the carburetor by tubing designed to carry the fuel. The pur pose of the pump is to suck fuel from the supply tank and push it into the ca:t.:buretor float bowl as it is required by the engine. OPERATION The pumping operation is accomplished through a rockerarm on the pump, contacting an eccentric on the engine camshaft. The link is hinged to the rockerarm so that it can be moved down, but cannot be raised by the rockerarm. The only function of the rocker arm spring is to make the rockerarm follow the cam. The link and diaphragm are moved by the diaphragm spring. The pump, therefore, de livers fuel to the carburetor only when the fuel pressure in the outlet line is less than the pres sure maintained by the diaphragm spring. This condition arises when the float needle valve is not seated and the fuel passage from the pump into the carburetor float chamber is open. When the needle valve in the carburetor float chamber is clo-sed, and held in place by the pressure of the fuel on the float, the pump builds up pres sure until it overcomes the diaphragm spring. This pressure results in almost a complete stoppage of diaphragm movement until further fuel is needed.

HOW TO DIAGNOSE FUEL PUMP TROUBLE Fuel pump trouble is of only two kinds. Either the pump is supplying too little gas or, in rare cases, too much.
If the pump is supplying too little gas, the engine either will not run at all, or will cough and falter.
FUEL SYSTEM Section A Page 3
ENGINE GETTING TOO MUCH GAS: More often than not, an oversupply of gas oline is caused by trouble somewhere else - not in the pump. So, first check the following: 1. Defective automatic choke. 2. Excessive use of hand choke. 3. Punctured carburetor float. 4. Defective carburetor needle valve. 5. Loosely connected fuel line, or loose carburetor assembly screws. 6. Improper carburetor adjustment. NOTE: If none of these is the cause of flooding or poor gasoline mileage, then the pump needs overhauling. FINAL CHECK: After overhauling, a simple check of the suction and pres sure should be made before in stalling the pump on the engine. This can be. done by holding the fingers over the inlet and outlet openings of the pump and manipulating the rockerarm by hand. The pump may then be reinstalled on the engine and tested. (See in stallation instructions below). It should prime itself, that is, fill the filter bowl, in about 30 seconds with the starter button depressed. If it fails to provide sufficient pressure, the dia phragm has been incorrectly installed, prevent ing the full stroke of the push rod, or the springs do not have sufficient tension: and it will be necessary to disassemble the pump to reinstall the diaphragm correctly or to replace the link age springs if this has not been done. INSTALLATION OF FUEL PUMP Use a new gasket between fuel pump mount ing flange and pad' on c rankc as e and tighten cap screws securely. Connect fuel lines, first making sure that there is no dirt on the fittings which might be drawn into the system.
If carburetor has not been removed there will usually be sufficient fuel in it to run the engine long enough to fill the fuel pump filter bowl. If there is an air leak between filter bowl and gasket, the pump cannot draw fuel into the bowl. To remedy this, install a new gasket and see that bowl seats squarely. Tighten clamp screw securely with the fingers only. If fuel pump bowl still doe s not fill, the trouble may be due to an air-bound condition. In this case the bowl should be loosened slightly so that air can escape and, by blowing in the gasoline tank filler neck, fuel will be forced into the pump. Then tighten bowl securely and start engine.
If the pump is supplying too much gas, you will be able to see gasoline dripping from the carburetor; or the engine will not run smoothly when idling. s are hard to start when getting too much gas.
LOCATING FUEL PUMP TROUBLE AL WAYS CHECK WHILE THE PUMP IS INSTALLED ON THE ENGINE. DON'T TAKE IT OFF TO CHECK IT. ENGINE NOT GETTING ENOUGH GAS:
If the engine is getting too little gas, the trouble may be in the pump, the fuel line: or the gas tank.
First, be sure that there is gas in the tank. Disconnect the outlet line from the pump, or the carburetor, whichever is easier to reach. Then, turn the engine over a few times, using the starting motor. It is be st to turn off the ig nition switch.
If gas spurts from the pump or the outline line, the pump, gas line, and tank are OK.
If no gas flows at all, or if only alittle gas flows, do the following:
1. Look for a leaky bowl gasketseat. In stall a new gasket if you are not sure.
2. Remove and clean the gas strainer which is inside the pump bowl. 3. Look for loose line connections. Check Tighten 4. Look for a clogged fuel line. Blowout with compres'sed air. 5, Make sure that all cover screws on the pump are tight. Make sure that the external plugs over pump valves are tight. 6, Inspect the flexible fuel line for breaks or porous condition.
If correction of the above six items does not place the pump in operating condition, it should be removed for replacement or overhaul.
PRINTD IN UNI'fE:O S'fA'tES OF AMERICA
FUEL SYSTEM Section B Page 1
CARTER MODEL-YF CARBURETOR

Description
The Carter carburetor model YF for the 220 and 240 Silver Diamond engines is essentially the same as conventional carburetors in that it has a high-speed fuel circuit, low-spleed cir cuit, and accelerating pump circuit. There is, however, a departure in the metho'd of controlling the fuel flow on part-throttle, wide-open-throttle and through the accelerating pump circuit as compared to carburetors pre viously used. A calibrated metering rod (Fig. 4) fits into the main jet. It becomes effective at low-part-throttle speeds and automatically positions itself according to the throttle opening thus producing proper fuel flow throughout part throttle and wide-open-throttle. The heart of the carburetor is the diaphragm (Fig. 4) which actuates the accelerating pump and the step-up action for wide-open-throttle fuel mixtures. The underside of the diaphragm is subjected to manifold vacuum by means of a channel down to the carburetor flange. This channel is re stricted by a bushing in the flange in order to ob tain consistent and smooth performance and to promote extra long diaphragm life. identifying the various assemblies when dis mantling the YF model carburetor for complete reconditioning. as outlined in the following step by-step instructions.
~"'f----
Air horn' and fuel bowl cover
lever
lever
Any movement of the diaphragm results in a corresponding movement of the metering rod. When the throttle is wide open the manifold vacuum drops sufficiently to allow the diaphragm to move upward thus shifting the metering rod to the wide open throttle step. A chamber above the top of the diaphragm sup plies fuel for the accelerating pump circuit. The diaphragm acts as a pump and the quantity of fuel discharged by the pump is controlled by the size of the pump jet or nozzle calibration (Fig. 2) and also the size of the fuel inlet hole to the chamber. There is no check valve on the in let. There is a check valve in the outlet channel near the pump jet to allow fuel to pass in an out ward direction only and also to prevent air from being sucked back into the chamber under cer tain conditions. The pump jet is free to flow at all times generally starting at a part-throttle engine speed of 1500 r.p.m. and continuing throughout wide-open-throttle. This carburetor has a unique feature in that no change in setting is required when it is used in conjunction with a sandwich type governor, re gardless of whether or not a vacuum by-pass is used around the governor. Illustrations (Figs. I to 8) show the location of the various parts. and will aid in correctly
PRINTED IN' UNITED STATES OF AMERICA
A-22880
Fig. I - Carter (Model YF) Carburetor
Low-speed or idling jet
Pump disc retainer ring
Fig. 2
Throttle lever stop
A-22900
Fig. 3
Fig. 6
Upper pump sp!ing Pump intake,_"_ __ strainer Pump Iifter.___-lIo>
Throttle shaft
link"
A.22899 A-22902
Fig. 7
Choke
Fig.
Ij
Choke valve
A-22974
Fig. 5
Fig. 8

MODEL YF - SERVICE PROCEDURE
To Disassemble
1. ReITlove pin springs, fast idle connector
rod spring, and rod (Fig. 1). 2. ReITlove air horn and bowl cover attaching screws (7), and choke tube claITlp asseITlbly (Fig. 1). 3. ReITlove air horn asseITlbly, and gasket. 4, ReITlove pUITlP disc retainer ring (using knife tip), retainer, and pUITlP check disc (Fig. 2). 5. ReITlove throttle shaft arITl asseITlbly, pUITlP connector link, shaft seal spring, dust seal washer, and felt dust seal (Fig. 7). 6. Loosen diaphragITl housing attaching screw, and washer assemblies (4) and lift out entire pUITlP and ITletering rod asseITlbly (Figs. 3 and 4). 7. RelTIOve diaphragITl housing attaching screws, pin spring, ITletering rod upper pUITlP spring retainer, upper pump spring, metering rod arm assembly, and pUITlp lifter link (Fig. 4). 8. ReITlove diaphragITl spring retainer, spring, and pUITlP diaphragITl asseITlbly (Fig. 4). 9. Carefully reITlove pUITlP intake strainer from housing, using tip of knife blade. 10. Remove metering rod jet. 11. Remove low-speed (idle) jet asseITlbly. Do not remove pressed in parts such as nozzle, pump jet or anti-percolator air bleed. (Fig. 2). 12. Remove body flange attaching screw (3), body flange assembly, and gasket (Fig. 1). 13. ReITlove idle adjustITlent screw, spring, idle port rivet plug, throttle lever assembly, washer, fast-idle arm, valve attaching screws (2), and throttle shaft. Then remove throttle shaft seal by prying out seal re tainer. Do not remove vacuum passage orifice (pre s sed in). 14. Remove float pin, float, and needle and seat assembly from air horn casting (Fig. 5). 15. RelTIOve choke valve screws and choke valve. Unhook choke spring and slide shaft from housing. Do not remove balance vent tube. NOT E: In normal service, choke lever assembly will not require replacing. How ever, if it has been bent or otherwise damaged requiring replaceITlent, proceed as follows: Pry off choke lever retainer ring and remove lever assembly (Fig. 8).
PRINTED IN uNITED STATES OF AMERICA
16. Wash all parts in carburetor cleaning solution and blowout passages with com pressed air. Do not immerse diaphragm assembly, PUITlE check disc or seals in cleaning solution. Inspect all parts for wear or damage and replace if necessary. Always use new gaskets.
To Reassemble
17. Group all parts, controlling the float cir cuit: float, float pin, needle and seat as seITlbly, air horn gasket. 18. Group all parts, controlling the low-speed circuit: throttle shaft seals (2), and re tainers (2), throttle shaft, throttle valve and screws, fast-idle arITl, throttle shaft washer, throttle lever, idle port rivet plug, idle adjusting screw and spring, gasket, attaching screws (3), low-speed jet, throttle shaft seal spring. 19. Group all parts, controlling the high-speed circuit: Metering rod, metering rod jet, pin spring. 20. Group all parts, controlling the pump cir cuit: pUITlp lifter link, .FUITlp connector link, throttle shaft arITl assembly, metering rod arITl asseITlbly, pump diaphragm housing, pUITlp diaphragITl assembly, pUITlp diaphragm spring, diaphragITl spring retainer, pump intake strainer, upper pump spring, upper pump spring retainer, pUITlP disc check, pump disc retainer, pUITlp disc retainer ring, diaphragm housing screw and washer as sembly (4). 21. Group all parts, controlling the choke cir cuit: choke valve and screws (2), choke shaft and lever as s eITlbly , fast-idle connector rod and spring, choke tube clamp asseITlbly, air horn attaching screw and washer assembly (7), pin spring (2). 22. Install throttle shaft seal and retainer in flange casting. 23. Install fast-idle arm, washer and lever as seITlbly on thr ottle shaft; slide shaft into place and install throttle valve. Carter trademark should go toward the idle port. when viewed from manifold side of flange. Tap valve and hold in place with finger be fore tightening screws. 24. Install idle port rivet plug and idle adjusting screw and spring. 25. Attach flange assembly to body casting. Use new gasket. 26. Install low-speed jet assembly.

39. Install air horn gasket and air horn as serrlbly. Install attaching screws and lock washers (7) and choke tube c1arrlp asserrlbly. (Tighten center screws first.) 40. Slide choke shaft and lever asserrlbly into place and connect choke lever spring. In stall choke valve. Center valves by tapping lightly and hold in place with fingers when tightening screws. 41. Install fast-idle connector rod with offset portion of the rod to top of pin spring to the outside. Install fast-idle connecting rod spring.
27. Install pUrrlp intake strainer in pUrrlp dia phragrrl housing and carefully press into recess. CAUTION: If strainer is even slightly darrlaged, a new one rrlust be used. 28. Install pUrrlp diaphragrrl asserrlbly in dia phragrrl housing, then install pUrrlp dia phragrrl spring (lower) and retainer. 29. Install pUrrlp lifter link, rrletering rod arrrl, upper pUrrlp spring and retainer. 30. Install rrletering rod jet; no gasket is used with this jet. 31. Install diaphragrrl housing attaching screws (4) in the diaphragrrl housing, rrlaking sure the edges of diaphragrrl are not wrinkled. Lower into place and tighten screws evenly and securely. 32. Install throttle shaft seal, dust seal washer, and shaft seal spring. 33. Install pUrrlp connector link in the throttle shaft arrrl asserrlbly. Install throttle shaft arrrl asserrlbly on throttle shaft, guiding connector link into pUrrlp lifter link hole. CAUTION: Linkage rrlust not bind in any throttle position. If binding occurs, loosen clarrlp screw in throttle arrrl, adjust slightly and retighten screw. 34. Install pUrrlp check disc, disc retainer, and lock ring. 35. Install rrletering rod, and pin spring. Con nect rrletering rod spring. 36. Metering Rod Adjustrrlent: Be sure flat of rrleter ing rod arrrl is parallel to flat of pUrrlp connector link before proceeding with rrletering rod adjustrrlent. With throttle valve seated, press down on upper end of diaphragrrl shaft. Metering rod should be seated in cast ing and rrletering rod arrrl (Fig. 3) flat against pUrrlp lifter link (A). If rrletering rod does not seat in body casting (check by pressing downward on rrletering rod) or seats before the rrletering rod arrrl rrlakes flat contact with pUrrlp lifter link. raise or lower by bending lip (B) on rrletering rod arrrl. Adjust float level as shown in Fig. 3. Width of gauge is 25/64" for YF-735S car buretor and 7/16" for YF-736S carburetor. A tolerance of plus or rrlinus 1/64" is per rrlissable in each float level setting. 37. Install needle seat and gasket asserrlbly, needle, float and float pin. NOTE: Stop shoulder on float pin rrlust be on side away frorrl bore oJ carbure tor. 38. Set float level to catalog page specifications. Measure frorrl rrlachined surface of casting (gasket rerrloved). Adjust by bending lip which contacts needle.
FUEL SYSTEM Section C Page 1
CARTER MODEL BBR-l CARBURETOR

(FOR DETAILED DISASSEMBLY INSTRUCTIONS SEE SHOP TALK NO. 35)
Float setting
Idle 1If----Flaoge assemhly

A. I 7083
Fig. I
Description
The Carter Model BBR-l-617SA carbur etor (Fig. l) is a downdraft carburetor, divided into five circuits which consist of the following: FLOAT CIRCUIT The float circuit controls the height of the gasoline level in the bowl (Fig. 2). A gasoline level too high or too low may cause trouble in other circuits, and make complaints hard to trace. The float circuit consists of a needle valve, seat and gasket, float, float bowl, float bowl cover, float lever, pin retainer, float pin, gasket and vent hole. LOW -SPEED CIRC UIT The idle or low-speed circuit controls the supply of gasoline to the engine during idle and no-load up to a speed of approximately 15 to 20 m.p.h. and it partially controls the supply of fuel for no-load or light loads at higher speeds (Fig. 3). The low-speed circuit consists of the idle
PRINTEO IN UNITED STATE'S OF AMERleA
Fig. 2 - Before adjusting float level, be sure float lever pin is firmly seated and that the float pin retainer is in position. Reset float level by bending I ip of float lever away from needle to raise level, or toward needle to lower float level. Bend vertical lip of float only. Use float gauge (SE-1639-IO) and check level as shown. Setting is 5/6~" plus 1/6~n below top surface of carburetor body casting and without the body gasket.
Idle adjusting
screw
}1
to
1}1
turns
Fig. 3 - Idle adjustment is ! to I! turns open. For richer mixture, turn the idle screw out.
orifice tube and plug assembly, air bleed, idle port, idle mixture adjusting screw, throttle valve, carburetor bore, and economizer. HIGH-SPEED CIRCUIT The intermediate and high-speed circuit consists of the step-up jet, step-up piston and rod assembly, main metering jet, main vent tube, diffuser holes, and air passage. PUMP CIRCUIT The acceleration circuit consists of the
FUEL SYSTEM Section C 2

11
accelerating pump spring, pump plunger and rod assembly, pump leather, inlet valve, outlet valve, pump jet air bleed. and pump jet. The accelerating pump is provided with an adjustable stroke setting. Set the accelerator link in the inne r hole in the throttle shaft leve r For r setting. use
12
CHOKE CIRCUIT This circuit is used only in starting and warming a motor, its purpose being to supply a rich mixture temporarily. It consists of a choke shaft and lever assembly, a choke valve, choke breather valve and spring, and a means of controlling the position of the valve. It incor porates a fast idle cam connected to the choke shaft by a rod. When the choke is closed the throttle valve is forc ed open slightly by the cam to make starting easier and prevent stalling. The choke breather valve allows sufficient air to enter so that the motor will start and not flood even though the choke valve is fullyc1osed.
4 3 z 1 Fig. 4 - Service Tools (See list belOW)
Service Tools
A special set of tools is provided to facil itate overhauling of the Carter carburetors, (see Fig. 4). These tools are as follows: SE-1639 Carter Carburetor Service Tools. Set consists of SE-1639-1 to 1639-13 inclusive: SE-1639-1 Grip handle for sockets (No. T 109-51) SE-1639-2 Handle bar for grip handle (No. T 109-53) SE-1639-3 Screw driver bit 5/16" (No. T 109-57) SE-1639-4 Screwdriver bit 11411 (No. T109 58) SE-1639-5 Screw driver bit 3116" (No. T 109-59) SE-1639-6 Socket, double hex, 9116" (No. T109-69) SE-1639-7 Socket, double hex, 5116" (No. T 109-64) SE-1639-8 Ball retaining ring inserter tool (No. T 109-75) SE-1639-9 Rivet extractor tool (No. TI09 43) SE-16 39-1 0 Floatlevel gauge (No. T 109-50) SE-1639-ll Main vent tube tool (No. T 1 09 195) SE-1639-12 Ball retaining ring removing tool (No. TI09-56) SE-1639-13 Metal box for SE- 1639 tools.
Carburetor flange gaskets
Carburetor Overhaul
(See Shop TalkNo. 35 for complete instruc tions and details ). When disassembling the carburetor keep the various groups of circuit parts together so that each group can be inspected and replaced completely before proceeding to the next group. Use a sectionalized pan or muffin tin to sepa rate each group of parts. Reassembly of the carburetor is practi cally the reverse of disassembly. A complete set of servicing tools is provided to facilitate overhauling of the Carter carburetors. These tools are available under SE-1639, and are shown in Fig. 4. Proper selection of carburetor flange gas ket is necessary when installing the carburetor on the manifold, see Fig. 5. U the carburetor is used in conjunction with a sandwich governor (governor mounted between carburetor and manifold), the gasket having four holes is used. Where no governor is used the slotted gasket is used. The slots in the gasket provide leads to the vacuum passage leading to the step-up piston cylinder. Either gasket can be used between the governor and manifold.
Used without governor
Used with governor

"'-23443
Fig. 5
FUEL SYSTEM Section D Page 1
HOllY MODEL 852-FFG CARBURETOR
Idle adjusting screws Fig. I
Throttle stop screw

A-22549
Fi g. 2
plates and a separate main metering system and idle system, one for each side. NOTE: In the following explanations, one side is generally referred to, unless mentioned otherwise.
Description
The Holley Model 852-FFG carburetor is a dual downdraft carburetor of the plain tube type, designed for use on engines of approximately' 260 to 390 cubic inch displacement. All of the metering jets and passages are located in the center of the main body, which provides for correct metering of fuel and air at all practical operating angles. The carburetor fuel system is fully balanced and sealed, the air for all vents and bleeds being taken from the main air entrance of the carburetor, thus, only air which has passed through the air cleaner is admitted to the carburetor. The governor actuated throttle mechanism is an integral part of the carburetor. designed to provide the needed power required for moving the throttle to governing speeds and is con trolled by a separately driven governor rotor. The combination of these two units has been engineered to give instant response and accurate governing. A power valve provides addition3-l fuel for high power operation, and a throttle actuated ac celerating pump provides the necessary fuel for fast engine pick-up. A throttle lever which is self-locking and self positioning is incorporated in this carburetor. This dual carburetor can be considered as two carburetors built into one unit. There are separate venturi tubes, idle tubes and throttle
PRINTJ;:.D IN UNITED S"I"A"rE$ 01" AMERICA
Idle Fuel System

The fuel from the carburetor bowl (12) passes through the main metering jet (13) into the idle tube (10) as shown in Fig. 2. Air is introduced into the fuel stream by idle air bleed (8). This fuel and air mixture then travels through the idle passage (1) through the chamber' around the bleeder plug (16) and to the continuation of passage (1) then discharges at idle transfer hole (2) and idle discharge hole (3). When the engine is set to idle at a speed of approximately 350 r.p.m. the mixture is dis charged out of the lower hole (3) only. As the throttle plate (5) is opened and the engine speed and air flow increases, the upper idle trans fer hole (2) starts discharging in addition to the lower hole at about 450 r.p.m. The action and timing are such that the discharge from the upper hole reaches a maximum at approximately 750 r.p.m. and then gradually becomes less effective as the main nozzle (15) begins to flow. The lower discharge hole (3) is provided with an idle adjusting needle (4). Turning this needle out (to the left) gives a richer mixture and turn ing in (to the right) a leaner mixture. The idle adjustment should be set with a vacuum gauge for the highest and steadiest vacuum reading or
FUEL SYSTEM Section D Page Z

At idle the vacuurn is the highest, and it de creases as the load of the increases. The piston (18) (actuated by vacuurn) and the spring (19) are held in the "up" position which allows the valve (17) to rernain closed until the vacuurn drops to approxitnately 7.5 to 6.5 inches of rnercury. Below this vacuurn the piston force is not great enough to resist the compressed load of the spring (19) and thus opens the power valve (17). Under load, as in clirnbing hills, etc., the vacuurn drops because it becomes necessary to open the throttle wider in order to rnaintain speed. When the vacuurn drops below 7.5 inches of rnercury. the power valve is opened by the piston stern. The fuel then flows into the power valve chamber and through the restriction (Zl) into the rnain well (6), and is discharged together with fuel frorn the rnain rnetering systern. This gives the additional fuel required for high speeds for heavy loads and low speeds at full throttle.
27-~-h
.... ~
25
11....,....,-'--;- 28
Accelerating Pump
A-22471
Fig. 3
the srrlOothest running and rnaxirrlUrn idle r.p.rn. When seating the idle adjustrnent needle (4), excessive force should never be used as this rnay cause a groove to forrn on the needle point. If this occurs, the adjusting needle will have to be replaced in order to obtain a satisfactory idle adjustrnent.
Main Fuel System

As the throttle is opened and the idle systern becornes less effective, the rnain discharge nozzle (15) in Fig. Z starts to deliver fueL This occurs at approxirnately 900 r.p.rn. road load. Between 900 and 1 ZOO r .p.rn., there is a definite blending of the idle and rnain fuel systern. In the above range all the fuel passes through the rnain jet (13) up through the rnain well (6) to angle channel (9). Here the fuel is atornized by the high speed bleed (7). and an additional sup ply of air is introduced to this rnixture by the bleeder plug (16) before being discharged through the vertical passage (14) into the venturi. The float bowl (lZ), Fig. Z, is vented to the atrnosphere through a balance tube (34). This systern, besides correcting float charnber air pressure for atrnospheric changes, keeps dirt out of the fuel systern and reduces air cleaner cIo g g ing e He c ts to a rn inirnurn.
The accelerating purnp shown in Fig. 3 is con nected to the throttle shaft by rneans of link (33) and operating lever (3Z). The function of the accelerating assernbly is to ternporarily en rich the rnixture for rapid acceleration. The fuel is drawn into the pump charnber (Z9) through pump inlet check valve (Z5) on the upward stroke of pump piston (30) when closing the throttle. When the throttle is opened, the pump piston (30) moves downward. closing the pump check valve (25) and forcing the displaced fuel through passage (Z4) to raise the purnp discharge valve (Z8). The accelerating fuel charge then goes around the valve and out the purnp discharge nozzle (Z6). A slot in the pump piston stern allows the purnp operating rod (31) to overrun the purnp piston (30) when the throttle is opened suddenly. This overrun causes the purnp piston to be subjected to the pressure of the spring (Z7), thereby giving a prolonged discharge of the accelerating fuel. The accelerating purnp is provided with an ad justrnent for varying the quantity of the accel erating charge. This adjustrnent is rnade by changing the position of the purnp link (30) in the holes of the operating lever (3Z). The position farthest away frorn the pivot point is the cold weather setting since it gives the greatest discharge. The rniddle position is the average setting, and the position nearest the pivot is used under conditions of very hot weather.
POWER MIXTURE SUPP L Y

The power valve vacuurn piston (18) and the spring (19) shown in Fig. Z are actuated by the vacuUITl below the throttle plate (5) which cOITlITlunicates with the top of the piston (18) through pas sage . (20).
ADJUSTMENTS AND SERVICE HINTS

TOOLS REQUIRED - This carburetor can be cleaned or repaired without the use of special tools.
cover raises the level; pushing it away from the cover lowers the level, NOTE: The fuel inlet valve, valve seat, and gasket are serviced as an assembly and should be used as supplied in factory :matched sets. When replacing the valve seat, be sure to use a screwdriver with a blade wide and heavy enough to fill the slots in the valve seat. IDLING SPEED ADJUSTMENT - First set the idling speed by adjusting the throttle stop screw, (Fig. 5). The idle :mixture is controlled by the idle ad justing screws (Fig. 5), NOTE: These screws regulate fuel flow and are not air bleed needles. Tur these screws in (or to the right) :makes the :mixture lEraner, and turning the:m out (or to the left) :makes the :mixture richer. Screws should be turned in until they just touch the seat, then backed off one full turn. Care should be taken not to ja:m the screws agains t the s eat tight enough to groove the points. If this occurs, the needles will have to be replaced before a satisfactory adjust:ment can be :made. The screws should be adjusted with the fingers to avoid da:mage. When the engine has war:med up, turn both idle screws in until the engine starts to slow down, then turn both idle screws out until the engine starts to slow down. A point half way between these two will be very close to the correct idle :mixture. After arriving at the correct :mixture, it :may be necessary to reset the throttle stop screw to obtain the correct idle speed. Changing the speed :may :make a slight change in the idling :mixture. In the event this occurs, re-adjust the s crews as outlined above. NOTE: When adjusting the idle :mixture it is i:mportant that both idle screws be set at ap proxi:mately the sa:me nu:mber of turns open, otherwise, the off idle perfor:mance :may be erratic. FAILURE TO IDLE PROPERLY AFTER AD JUSTING - Be sure :motor is tuned to speci fications. Check for air leaks in intake :mani fold gaskets, carburetor body, bowl and flange gaskets.
Fig.
Before making any adjustments to the carburetor, it is important that the breaker points and spark plugs be properly spaced, the ignition timing cor rect and valve tappets set to proper clearance. Check all carburetor asse:mbly screws and mani fold flange bolts, see that they are thoroughly tightened and that there are no leaks at gaskets. FLOAT LEVEL - Proper carburetor perfor :mance is dependent on :maintaining the correct fuel level in the bowl. The float level can be set accurately, when the air horn is off, by gauging the distance between the botto:m of the float and the flange surface of the air horn. Holding the air horn upside down, less gasket, and with the float in the closed position, :measure the distance fro:m the flange surface of the air horn to what would nor:mally be the botto:m side of the float, not the soldered sea:m (Fig. 4). The correct distance that it should :measure is 1-11/32". To correct the float setting, the float lever ar:m (11), Fig. 2, should be bent up or down to bring the float within the established limits and thus correct the fuel level for best opera tion. Pushing the float toward the float cha:mber
'"..,y
"~'I
I I "nl
i
If the idle is erratic and not sensitive to ad just:ment, check the float level in the float bowl. Check the idle tubes (10). They :must be tight on seat in nozzle bar casting (15), Fig. 2.
ACCELERATING PUMP ADJUSTMENT - When the engine does not accelerate properly, check the accelerating pu:mp syste:m for dirt. If the pu:mp inlet check valve (25), Fig. 3, does not seat, fuel will return to the float bowl instead
screws
Fi g. 5
Throttle lever ',, stop screw A-22241
PRINTEO IN UNITEO STATES 0'" .....n:;~lc ...

2. Remove the main jets using a screw driver having a screw starter blade. See Fig. 39. NOTE: If the jet fails to stick to the end of the removing tool, but falls off into the fuel bowl, it may be necessary to remove the air horn assembly. 3. Install the main jets in the reverse of the removal operation. No gaskets are used with the main jets. NOTE: Do not try to change the size of the power valve restriction (21) Fig. 2, or the pump discharge nozzles (26) Fig. 3, as this will cause erratic performance. ECONOMY COMPLAINTS - Changing jets rarely increases economy more than slightly and often ruins performance. Make a thorough check on the condition of the motor with a compression gauge and make sure valves are in good condition. In a vehicle, check for dragging brakes or extra friction. Do not merely take a customer's word on mileage; run a gas test with a scientific mileage tester. Check float level in carburetor bowl and make sure the fuel pump pressure is not excessive. Then, if there is still cause for complaint, the various points as outlined above should be carefully checked over.
of dis cha r ging through the pump dischar ge passages (26). This can be checked by re moving the main body cover and operating the pump with a small amount of fuel in the bowl. If the check ball is leaking, air or fuel will bubble back into the float bowl through the inlet hole. After cleaning this seat, extreme care should be taken when reinstalling the pump piston to be sure the piston leather is not damaged and that it contacts the cylinder wall. If the leather is not a snug fit against the cylinder wall, fuel will leak by the piston on acceleration, causing a weak discharge. To clean the accelerating pump system, remove piston assembly and check ball retainer and check ball from bottom of cylinder. Remove pump discharge nozzle, and valve (28) Fig. 3. Re move pump discharge needle valve. All chan nels can then be cleaned of all foreign matter by flowing out with compressed air. The small holes or restrictionsin the discharge nozzle should deliver a fine, solid and round stream. When the system is in good condition, a quick steady stream will flow from the discharge out let the instant the throttle is opened. MAIN FUEL SYSTEM - To check for trouble at intermediate speeds, be sure all gaskets are tight. Remove main jets (13) Fig. 2, and check size in accordance with specifications. Clean main jets, main jet passages and main discharge nozzle with compressed air. NOTE: Never attempt to clean any of the small holes or restrictions by forcing any object through them. This is apt to enlarge the hole or distort the shape and change the calibration. HIGH SPEED COMPLAINTS - For high speed complaints, check the power valve (17), Fig. 2, as well as the main jets (13) in accordance with the above instructions. Clean all passages with compressed air. Check the fuel pump pressure to be sure it is sufficient to maintain fuel level in the bowl. Check float travel to insure full opening of the inlet valve. ALTITUDE OPERATION - In some cases in high altitudes, it may be necessary to use leaner metered main jets. Usually a 5% or 10% leaner jet will compensate for any variation in altitude. The metering jets are .marked in thousandths of an inch of hole diameter; thus, the smaller the hole, the smaller the number on the Jet. The main jets can be removed and installed without disas sembling or removing the car buretor from the engine in the following manner:
Fig. 6 - Showing adjustment provided for accel erating pump stroke. Ho. I hole shortens pump stroke. No.2 length-increases pump stroke, The No.2 hole is the intermediate and recom mended position,
GOVERNOR - MODEL 1174

This engine speed governor has been designed and engineered as an integral part of the Holley Carburetor. The governor is a vacuum con trolled device featuring all the advantages of a
1. Remove the two main jet passage plugs

and gaskets from the car bur etor main body. Removal of thes e plugs will drain the fuel bowl. See Fig. 38.
Fig. 7 - Detai Is of governor.
Spinner or rotor housing is located at distributor,

The diaphragm chamber (33) in Fig. 9 is con 'nected to the governor valve air bleed orifice (50) in Fig. 7 by means of a c onve ntional pipe line (34). The air bleed supply enters the rotor housing (52), Fig. 7, from a pipe line (42) at. tached to the engine air cleaner or carburetor as shown in Fig. 7. Vacuum to the diaphragm (33), Fig. 7, is sup plied by means of the two channels (37) ,and (38) as shown in Fig. 8. Channel (37) opens mto the carburetor above the throttle plate and channel (38) below the throttle plate. These two openings are connected by channel (29), Fig. 8, which in turn is directly connected ~o channel (36) as shown in Fig. 9. The vacuum 1S controlled by the governor by-pass channel jets (39) instead of the variable restriction formerly used. A detailed description and the operation of the above mentioned features follows:
mechanical governor without resorting to lengthy and complicated linkage. The governor can be cleaned and serviced without the use of s})ecial tools, The governor is made up of two units (see Fig. 7). The control at the engine end of the governor consists of a governor valve (47), an adjusting screw (48) and a spring (49) assembled i:r: a rotor (41) which revolves at one half the eng~ne speed, in a housing (52), attached to an engme driven shaft (43). The controls at the carburetor end of the governor unit consist of a diaphragm (35) which is connected to the goverl1or lever (45) by a short rod and a tension spring (46) which is also attached to the governor lever (45) and tends to hold the throttle open.
Governor Operation
When the engine is running at idling speed, the throttle is controlled by the external lever (2), Fig. 8, and the pin (54) which is held against the internal lever (53) on the throttle shaft by the accelerator spring, as shown in Fig, 8. At idling speed, the governor valve (50) in Fig. 7 is held away from the air bleed orifice (50) by the spring (49) which is fastened to the governor adjusting screw (48). As the accelerator is
54
53
38 Fig, 8
A-22240

When the accelerator is released the control is taken away from the governor by the external throttle lever, and the governor connecting (40) then closes the throttle to bring the engine to any desired lower speed. NOTE: The governor adjustments have been set at the factory to operate the engine at the proper recommended speed. It is not likely that the adjustments will change once they are set.
Governor Adjustments and Service Hints

To adjust the governor cut-off speed, proceed as follows:
1. Remove the seal from the screw (51) that

will be found on the side of the governor housing (52) in Fig. 7. 2. Remove the screw from the housing. 3. Rotatethe engine until the end of the governor rotor (41) in Fig. 7, which carries the ad justing screw (48) is in line with the hole from which the screw (51) was removed. 4. With a suitable screw driver turn the ad justing screw to the RIGHT to INCREASE the engine governed speed or to the LEFT to DECREASE the speed. NOTE: Where the governor has been dis assembled andserviced, after reassembling turn the adjusting screw (48) to the right until it stops then turn the screw to the left three full turns. Final adjustment is then made after the governor has been as sembled to the engine as outlined above in operation 4.
Fi9. 9
moved to and held in the full open position to increase the engine speed, the governor spring (46) in Fig. 7, pulls the throttles to the wide open position to remain there until the engine r.p.m. has reached the predetermined governor cut-off speed. At this point, the governor mechanism which has kept pace with the engine speed is ready to go into action and take over control of the throttle, causing the accelerator system to become ineffective for further engine speed increase. The action of the mechanism is, that when the engine speed increases, the gover nor valve (50) in Fig. 7, stretches the spring (49) and moves toward the a,ir bleed orifice (50) thus restricting the bleed to the diaphragm (35). As the air bleed to the diaphragm is reduced it permits the suction supplied by the orifices (37) and (38) in Fig. 8, to operate the diaphragm. As this suction incr.eases, the diaphragm power overcomes the tension of the governor spring (46) in 7, and takes over full control of the throttles. The engine governed is then held constant by the valve (47) being balanced between the pull of centrifugal force actuated by the rotation of the shaft (43) and the tension of the spring (49) in Fig. 7. Any slight change in speed or load will cause the governor valve (47) to act immediately either to increase or decrease the amount of air bleed through orifice (50), which in turn causes an instant response from the diaphragm to increase or decrease the throttle opening.
HOLLEY CARBURETOR AND GOVERNOR OVERHAUL

The carburetor and governor can be overhavled with ordinary tools. Clean all loose dirt from carburetor assembly before proceeding with the foHowing instructions: CAUTION: Do not immerse the carburetor as sembly in cleaning solvent as the solution may cause damage to leather seals and governor diaphragm. Do not direct compressed air stream into air vent tubes in air horn as air pressure will damage float.

Air horn
and float
bowl cover
assembly
Main body assembly ---~
Throttle body _ _ _ _
assembly
Governor body assembly
Fig. 12 Fig. 10
Fig. 10 The carburetor is in reality an as sembly of four major subtrassemblies. These assemblies are identified above and should be disassembled and kept together in their respective groups.
Disassembly
Disassembly of the carburetor is as follows:
Fig. 13
. 11 -
Loosen screw in choke lever clamp and remove lever. Remove two choke wire bracket re
taining screws and lockwashers and
remove the choke wire bracket
I~
12 -
. 13 - Remove six air horn assembly screws and lockwashers.

PRINTJED IN UNITEO STATES OF AMERICA
Fig.
Fig. 14 - Separate air horn from main body as s ern bly and remove gasket. Be careful not to damage float. Fig. 15 - Remove float shaft and float. Fig. 16 - Remove fuel valve needle. Note: The fuel inlet valve, seat and are serviced as an assembly and should be used in matched sets as supplied. Fig. 17 - Remove fuel valve needle seat and gasket using a large screw driver that fits the slot properly or SE-1190-14 wrench. Fig. 18 - Remove ec onomizer piston and stem assembly. Use special wrench to fit piston retainer. Fig. 19 - In removing the choke plate note that the two choke plate screws are up set and must be filed flat before re moving to prevent breakage or strip ping of threads in shaft.
Fig. 17
Float shaft
Fig. 15
A-22155
Fig. 18
4..~~
A-22484
Fig. 16
F j g. 19

Fig. 20 Fig. 21 Relnove the two choke plate screws. Relnove choke plate, shaft and felt
packing. Do not attempt to relnove vent
tubes. Do not relnove plug froln end
of choke shaft bars. All relnovable
parts have been stripped frOln air
horn and float bowl cover asselnbly
and should be kept together as a group
ready for cleaning and inspection
preparatory to reasselnbling.
Relnove cotter pin holding acceler
ating pUlnp link in place.
Remove the two throttle operator
shaft housing asselnbly retainer
screws and relnove housing asselnbly.
Relnove accelerating pUlnp link. Note; It is not necessary to relnove the throttle operator shaft housing. asselnbly when changing pUlnp link to secure better engine perforlnance or to adjust carburetor for clilnatic changes. It was relnoved here to show the pUlnp link lever lnore clearly. Relnove the throttle operator shaft asselnbly. Relnove the pUlnp operating rod stud. Relnove the accelerating pUlnp opera tor rod and piston asselnbly. Disasselnble the pUlnp rod and piston by cOlnpressing the sP:"'ing and relnOV ing the pUlnp rod froln the piston slot. Relnove accelerating pUlnp operator rod seal. Use narrow blade screw driver and pry out felt retainer and relnove felt.
Fig. 22 Fig. 23 -
Fig. 24 -
Fig. 21
Fig. 25 Fig. 26 Fig. 27 Fig. 28 -
Fig. 29 -
F;g. 22
Fi g. 20
PRINTEO IN UNI'I"(O STATES OF AMf.:RtCA
Fig, 23
FUEL SYSTEM Section D

Page 10
1Less fuel
2 Average 3 More fuel
A-22529
Fig.
2~
Fig. 27
A-22212
Fig. 25
Fig. 28
Rod--
Stud
Fig. 26
Fig. 29

Fig. 30 Remove the two brass air bleed plugs
and gaskets located at the top of the
main discharge nozzle bars.
Remove the two nozzle bar clamp screws and lockwashers located nearest the fuel reservoir and re move clamp. Remove the accelerating pump dis charge nozzle and gasket. Turn the casting upside-down and catch the coiled spring and ball check resting in the pump discharge nozzle well. Remove the two idle tubes from the main discharge nozzle bars, using a
screw driver.
Fig. 31 -
Fig. 32 Fig. 33 -
Fig. 34 -
Fig, 32
Fig. 30
Fig. 33
Fig. 31
Fig,
3~
FUEL SYSTEM Section D Page 12 Fig. 35 Fig. 36 Fig. 37 -
Remove the remaining two nozzle bar clamp screws and remove clamp. Remove the two nozzle bars and gaskets. Use a wire having a short hook bent at 90 0 and remove the accelerating pump inlet ball check retainer spring from the bottom of the pump chamber. Turn the casting upside down and catch the inlet ball check. Remove the two main jet passage plugs and gaskets.
Fig. 38 Fig. 39 -
Remove the two main jets using a screw driver or SE-1l90-2 jet wrench. Fig. 40 - Remove economizer valve and gasket in bottom of fuel bowl using a screw driver with a wide blade. Fig. 41 - Lay casting on its side and remove two throttle body to main body as sembly screws. Pass screw driver through the carburetor mounting stud holes in base.
Fig. 37
Plugs and gaskets

A-221?O
Fig, 38
Fig, 35
Main jets
A-22IS?
Fig, 36
Fi g. 39

Fig. 42 Turn casting over and remove the
third throttle body to main body as
sembly screw. Access to this screw
is by means of a hole in carburetor
mounting flange face.
Separate the main body from the throttle body assembly and remove gasket. Retain all parts removed from main body assembly as a group for cleaning and inspection. Remove seal and wire from governor body cover plate screws. Remove cover plate screws and lock washers. Note: Plug screw located in c over plate. This s crew serves to plug blind hole in governor housing and has no effect on carburetor opera tion. Remove governor body cover plate and gasket.
Fig. 43 -
Fig. 44 Fig. 45 -
Throttle body
Fig. 112
Fig. 46 -
Fig. '0
F ; g. ij3
Throttle body to
main body assembly screws
A-221S7
Fig.
'I
A~EFUCA
Fig. 'II
P"RINTEO IN UNITED STATES 0 '
FUEL SYSTEM Section D Page 14 Fig. 47 -
Remove the governor spring with the fingers. Be sure to hold throttle open while removing spring. Remove cotter pin holding diaphragm rod to governor lever. Remove governor lever retainer nut and lockwasher. SE-1l90-9 wrench fits this nut. Remove governor lever from throttle shaft. Remove the three screws and lock washers that hold governor housing to throttle body. Remove the governor housing from the throttle body and remove gasket. Note: The throttle shaft leather seal
and washer will usually adhere to
governor body, but were placed on
shaft to show correct assembly.
Fig. 48 Fig. 49 -
Fig. 50 Fig. 51 -
Fig. 52 -
Fig. 1J7
Fig. 1J8 Fig. 1J5
Fig. 1J6
Fig. 1J9
Remove coiled seal retainer spring from throttle body. Fig. 54 Remove two idle adjusting screws and springs. Fig. 55 - Mark the throttle plates "I" and "2" and also mark the same number on the casting flange as shown. Scribe lines across the full width of the plates against the shaft. This will assure installation in their proper barrels and in correct position when reassembling.
Fig. 53 -
Fig. 50
Governor to throttle
body screws
Fig. 53
A-22183
Fig. 51 Fi g. 51j.
Fig. 52
PRINTED IN UNITED STATES OF ",MERiel.
Fig, 55
The four throttle plate screws have been upset and must be filed flat before removing to avoid breakage or stripping of threads in shaft. Re move four throttle plate screws. Fig. 56 Fig. 57 Fig. 58 Remove the throttle plates. Remove the throttle stop screw and spring. Remove the retainer spring holding the throttle shaft and bearing as sembly in place. Remove the throttle shaft and bear ing assembly by tapping threaded end of sha~ lightly with a soft hammer. Note: Do not attempt to remove the bearing on end of shaft as this bear ing is pressed and staked in place. Insert a 9/32" brass rod through shaft hole, at throttle lever end, and remove throttle shaft bearing by tapping lightly on the brass rod.
Fig. 59 -
Fig. 60 -
Fig. 58
The foregoing completes removal of all parts from the throttle body; parts should be kept to gether in a oup ready for cleaning and in spection b veassembly.
Clutch
Throttle shaft
Fig, 59
A-22196
Fig. 56
Bearing
Fig. 57 Fig. 60
A-22185

Fig. 61 - ReITlove the washer and leather seal froITl governor body. Fig. 62 - ReITlove the governor housing by-pass jets. The asseITlbly of governor by pass passage jets is shown above. The outside diaITleters of the "Aft jet and "B" jet are not identical, hence it is iITlpossible to asseITlble theITl incorrectly. Fig. 63 - ReITlove the seal and wire froITl the three governor diaphragITl cover retaining ITlounting screws. Fig. 64 _ ReITlove the eight governor diaphragITl cover retaining screws. Fig. 65 - ReITlove diaphragITl cover. Use a soft haITlITler and tap lightly around the edge of the cover until cover breaks loose. DO NOT PRY COVER OFF. ReITlove the diaphragITl and rod as seITlbly. If diaphragITl sticks to the body flange, carefully work it loose with the finge r s.
Fig. 63
Diaphragm Fig. 61
Fig. 65
NOTE: The foregoing instructions COITl pletely strip the governor; keep all the COITlpO nent parts togethe r for cleaning and inspection, in preparation for reasseITlbly.
Fig. 62
PRINTED IN UNITED STATES 0'" AMERICA

blunt center punch for this operation, also support opposite side of shaft to prevent bending the shaft.
Cleaning
1. The disasseInbled carburetor should be segregated into the four or groups. Clean the castings and in each in dividual group. Wash thoroughly in cleaning solvent and blow all passages with cOInpressed air. CAUTION: Do not wash LEATHER parts or governor DIA PHRAGM in cleaning solvent. If these parts are dirty wipe theIn with a soft cloth. 2. Wash Inetal parts in a cleaning solution and rinse theIn in a solvent solution. Dry all parts thoroughly. 3. ReInove all carbon deposits frOIn throttle body bores and throttle CAUTION: A wire or drill used to clean Inetered jets or dis char ge holes will ~::'::~L...!~~-=-=~~::' ation and
6. CHOKE LEVER. Install on shalt with choke

wire lock screw in swivel nut facing away rOIn air horn casting and with outer edge of lever flush with end of shaft. Hold choke plate in open l?osition and tighten lever claxnp screw. 7. FUEL INLET VALVE SEAT ASSEMBLY AND GASKET. Whenever a carburetor has been in continual service for 10,000 Iniles or Inore, and when carburetor is being overhauled for any reason whatso ever, always replace original fuel inlet valve asseInbly with a cOInplete new unit. Install a new fuel inlet needle, seat and gasket. Wipe taper of needle valve with a soft clean cloth before inserting in valve seat. 8, FLOAT. Replace float if it is corroded or daInaged in any way. If the lip on the float lever is rough, polish with a sInall piece of No. 320 wet or dry abrasive paper. Place float in position in hinge bracket. Be sure float balancer spring is inposition. 9. FLOAT LEVER SHAFT. Replace shaft if bent or shows excessive wear at bearing ends. AsseInble shaft and float to bracket. There should be at least .005" clearance on each side of float lever and asseInbly bracket. If end play is insufficient, reInove the float and spread the bracket. 10. FLOAT LEVEL SETTING. Hold air horn asseInbly at eye level (float side up) and gauge float. Gauge Inust just slide over top of float when float is in closed position. If float is too high, press it down gently with the fingers and regauge. If float is too low, reInove it and insert a narrow screw driver between the float bracket and lip. Twist the screw driver enough to raise the lip. In stall float and regauge. (See Float Level Adjus tInent.) 11. ECONOMIZER PISTON AND STEM AS SEMBL Y. ExaInine asseInbly closely. Replace if piston is worn, steIn is bent 0 r spring is"daInaged. Install ecorioInizer piston and steIn asseInbly. 12. After cOInpleting installation of econoInizer piston and steIn asseInbly place to one side until ready to asseInble to Inain body.
Inspection and Assembly

Inspect and asseInble c and parts by groups. NOTE: Inspect all parts thoroughly, check closely for any possible defect. Replace any doubtful parts. Never use old gaskets when reas seInbling the carburetor.
Air orn and Float Bowl Cover H

Replace al1 defective parts and asseInble as follows: 1. CASTING. ExaInine for cracks or breaks. Be sure sealing surfaces of casting are SInooth and clean. Float lever bracket Inust not be twisted or bent. 2. Install new choke shaft felt in choke shaft hole c ounte r bor e. 3. AsseInble choke wire claInp bracket to casting with the two Inounting screws. Mount bracket with the claInp end to the left when holding casting with air filter side fac up. 4. CHOKE SHAFT. If shaft is bent or indi cates excessive wear, use a new shaft. In stall choke shaft. 5. CHOKE PLATE. the plate if poppet valve asseInbly is To facilitate instal1ation of the choke plate, rotate the choke shaft until the countersunk holes face the vent tubes. Hold the shaft in this position and insert the choke plate froIn the float side of casting and with the poppet valve steIn pointing away froIn vent tubes. Center the plate in the bore and asseInble to shaft using new screws. The screws Inust be up set to lock theIn firInly in place. Use a
Main Body
1. CASTING. Al1 gasket surface s Inust be SInooth and clean. If any sealing surface is daInaged to the extent that a ct seal is iInpossible, the casting Inust be replaced.
9. DISCHARGE NOZZLE BARS. Replace nozzle bars if damaged in any way. All drillings and channels must be free from dirt (blowout thoroughly with compressed air). 1 O. Install four new neoprene nozzle bar gaskets in place. Note: In all cases where nozzle bars have been reITIoved from casting for any reason use new gaskets when reas sembling. To install gaskets, place a gasket on the blade of a narrow screw driver and put blade at edge of gasket seat. Then elevate handle of screwdriver until gasket slides into place. 11. Install nozzle bar s in place, being careful not to dislodge gaskets.
Fig. 66
Note: Nozzle bars are marked with the letter "R" or OIL" meaning right or left on the outer wall of the idle tube housing. (See Fig. 36). Place nozzle bar marked "R" next to accelerating pump chamber. 12. Place nozzle bar clamp in position on op posite side of fuel bowl. Insert short clamp screws and star washers through clamp and tighten screws just enough to hold nozzle bars in place. 13. IDLE TUBES. Replace idle tubes if bent or otherwise damaged blowout idle tubes with compressed air and install in place. Fig. 34. Idle tubes ITIust be tight on seats. 14. Install the remaining nozzle bar clamp, first being sure to install the fuel pump dis charge nozzle and gasket. Also make sure fuel pump discharge ball check and spring are still in place. Tighten both claITIps. 15. Install new bleeder plug gaskets in top of nozzle bars. Install bleeder plugs in place and tighten. 16. ECONOMIZER VALVE. Replace valve if spring is weak or if the valve stem is bent. Place a new gasket on valve body and as seITIble valve in place. (Fig. 40). 17. ACCELERATING PUMP. Examine pump piston, operator rod, operating spring, leather cup and cup expander spring. Re place any worn, bent or distorted parts. 18. Assemble pUITIP rod, spring and retainer to piston and install the pUITIP asseITIbly in the pUInp chamber of the ITIain body casting. Be careful not to damage the leather as it is entered into the pump chaITIber. 19. PUMP OPERATING ROD STUD. Replace stud if bent or badly worn. Using a small accurate fitting open end wrench (1/4"') tighten stud to rod.
2. Pump the operator rod and seal. Install a new felt seal and retainer washer and stake as shown in Fig. 66. 3. JETS. Replace jets if screwdriver slot, orifice or threads have been damaged or otherwise mutilated. 4. Install jets in casting. 5. ACCELERATING PUMP INLET BALL CHECK. Replace ball check if it is cor roded or nicked. Drop ball into pump cham ber and work into seat housing. (Ball seat is located in cut-away portion of chamber floor, in which the bent end of the retainer fits .) 6. RETAINER SPRING. Replace spring if bent or twisted (spring ITIust lay flat). Install spring in pUITIP chaITIber keeping bent end of spring in line with ball check. Then with a 5/8" diaITIeter dowel pin of wood or fiber, press the retainer in the groove at bottom of chaITIber. Be sure bent end of spring is directly over the ball when in place 7. PUMP DISCHARGE BALL CHECK AND SPRING. Replace ball check if _corroded 0'1' nicked. Replace coiled spring if corroded or distorted. Install ball check in pUITIP dis char ge well. Install coiled spring over ball check. 8. PUMP DISCHARGE NOZZLE AND GASKET. Rep1;:tce if damaged in any way. Discharge holes ITIust be clean (blowout with com pressed air). Place a new gasket in position on nozzle and hold asseITIbly until ready to install bar claITIp after main dis char ge nozzle bars have been placed in position.
PRINTED IN UNI'fED STATES OF AMERICA

3. THROTTLE PLATES. Replace throttle plates if they are nicked or otherwise damaged. To install plates, place throttle body on bench with the manifold mounting flange up and the threaded end of the throttle shaft to the left. Rotate the shaft until the countersunk holes in shaft are facing the idle adjusting screw bosses.
Note: During the disassembly operation, the plates and barrels were marked No. 1 and No.2. Place No. 1 plate in No. 1 barrel. Install the throttle plate with the bevel edge down and facing the countersunk side of shaft. Close the plate, and using the pre viously scribed lines as a guide, center the plate in the bore and assemble plate to shaft with new screws. Before drawing screws tight, be sure the plate is properly centered. Repeat same procedure to install the other throttle plate. Then check the four as sembly screws to be sure they are tight,
20. Assemble main jet plugs and gaskets to casting. Blowout casting thoroughly with compressed air.
21. Assemble air horn to main body. Recheck

the float setting using gauge. Holding as sembly gasket in place assembly air horn to main body and tighten all screws tight. Be sure throttle lever spring bracket is in stalled in correct position at accelerating pump chamber. See Fig. 67. Place as sembly to one side being careful not to damage accelerating pump operating rod.
4. Upset the threaded ends of the screws with a blunt center punch and a light harruner. Be sure to support opposite side of shaft to prevent bending. After upsetting screws, check the shaft to make sure it oscillates freely. If shaft binds or drags, tap screw heads lightly with a bras s rod until shaft operates freely.
5. Rest throttle body on bench with threaded end

of shaft up.
Governor Body
1.
Check all sealing surfaces for cracks, nicks, or imperfections. Replace casting if defective. Using compressed air, blow out all governor channels. Replace governor body, etc. LEATHER BEARING SEAL AND STEEL WASHER. Replace leather seal if worn or otherwise damaged. Replace the steel washer if it is damaged. Install leather seal in governor body so that the flat side of the seal is up. Install steel washer over leather seal. Install coiled retainer spring against bearing in throttle body.
Fig. 67
Throttle Body
Inspect and assemble throttle body as follows: 1. THROTTLE SHAFT BEARING. Replace bearing if worn, corroded or damaged in any way. Bearing must rotate freely and be free of gum and grit. Install the bearing in the throttle body bearing boss on the gover nor side and with a brass rod lightly tap bearing in place. Note: Bearing must be installed with letter ing on race visible after installation. 2. THROTTLE SHAFT AND BEARING. Re place the assembly if the shaft is bent or if threads are stripped. Replace the as sembly if the bearing is corroded, damaged or worn or if throttle clutch is loose. Bearing must be free from gum or grit. Install throttle shaft and bearing. Install throttle shaft bearing retainer.
2.
3.
4.
5. Assemble governor body to throttle body,

Be sure gasket is correctly lined up before inserting the three assembly screws and lockwashers. Draw assembly down tight.
6.
GOVERNOR DIAPHRAGM AND ROD AS SEMBL Y. Replace assembly if diaphragm is burned, torn or otherwise damaged. Replace the assembly if the rod is bent or twisted.

Note: Sealing surfaces of diaphragIn housing and cover must be clean and free from nicks or burrs.
13. GOVERNOR COVER AND GASKET. Install a new gasket and install cover to governor body. Install seal wire in cover screws and seal.
7.
Install diaphragm assembly to housing with the bent end of the rod parallel with the throttle shaft and pointing away from the throttle body. (See Fig. 48). Line up the holes and place diaphragm cover in position. Note: Be sure that suction connector tube (Fig. 65) in cover fits into suction channel in the body properly.
Throttle Body Idle Screws and Shaft Assembly

1. IDLE ADJUSTING SCREWS AND SPRINGS. Replace screws if the tapered points are badly scored or bent. Replace the springs if they are corroded or distorted. Install adjusting screws and springs. Note: Turn screws in with the fingers until they are seated. (Do not use a screw driver.) Then back screws off seats one full turn.
8. Assemble cover to body with eight screws

and lockwashers. Thread all screws in until both flange surfaces nearly corne together. Then with the thumb or fingers pull the diaphragm rod as far back (toward the throttle shaft) as possible, hold it there and tighten every other cover assembly screw tight. Then release the rod and ti g h ten th ere m a in in g s c r e w s Note: When inserting the cover screws, ob serve the three screws that are drilled for the seal wire. Space drilled screws as shown in Fig. 63. Install the seal wire and seal.
2.
THR OT T LE LE VER AND THROTTLE OPERATOR SHAFT ASSEMBL Y. Replace lever if bent or if ball stud is worn. Re place shaft if worn, or accelerating pump lever if loose or if clutch assembly is 100 s e. Replace housing if shaft bearing is down or if housing is damaged. Install throttle operator shaft in housing and place throttle lever in position (ball stud facing toward carburetor) and tighten lever clamp screw.
9. GOVERNOR LEVER. Replace the lever

if the pin is loose or if rod is worn. Start lever onto throttle shaft and work end of diaphragm rod into hole in lever. Press lever into position and assemble to shaft with hex, nut and lockwasher. Be sure that nut is started correctly. Use a 5/16" socket wrench.
3,
Install the two throttle operator lever shaft housing mounting screws and place gasket in position. Hold the assembly with throttle lever ball stud up and assemble to throttle body as shown in Fig. 23. Tighten housing mounting screws. Note: Check the assembly; if correct, the throttles will close when lever is turned counter-clockwise. Releasing lever should permit governor operating spring to pull throttle into full open position.
CAUTION: Excessive tension wilt strip the thr eads on the shaft. DO NOT DRAW THE NUT DOWN TOO TIGHT. 10. Push end of diaphragm rod through lever by placing a thin blade screw driver or similar tool under the rod. Lock rod to the lever with a cotter pin. Insert the cotter pin so that open ends point towards the dia phragm. Spread the ends of the cotter pins around the rod. 11. GOVERNOR OPERATING SPRING. Re place the spring if corroded or distorted. Install operating spring with the fingers by hooking the loops over pins. Be sure the loops drop into the grooves in the pins. 12. GOVERNOR BY-PASS PASSAGE JETS. Replace jets if worn or damaged. Install the by-pass jets in "A" and lOB" channel (Figure 62). Note: The by-pas s jets have different outside diameters to aid in making correct ins tallation.
4. THROTTLE LEVER STOP SCREW. Place spring over stop screw and install as sembly in throttle body. Holding throttle plates closed, turn the throttle stop screw in until throttles open enough to allow a .003" feeler to pass freely between edge of plate and wall of bore.
Main Body and Throttle Body Assembly

1. 2. Install new main body to throttle body gasket. Place main body in position on throttle body and assemble with the three mounting screws. (This operation is accomplished by reversing the procedure outlined in Fig. 41 and Fig. 42.) Tighten the three mounting screws.
3. Recheck all visible asse:mbly screws; :make sure all are tight. DO NOT DISTURB INITIAL SETTING OF IDLE ADJUSTING NEEDLES AND THROTTLE STOP ADJUSTING SCREW. 4. PUMP OPERATING LINK. Replace the link if bent, twisted or worn. Install link over pu:mp operator shaft stud first, then start pin end of link into No.2 hole on the throttle lever (for nor:mal operation). Push link all the way onto stud. 5. Install cotter key holding pu:mp link to stud, bend open ends of cotter key around stud, Note: The reco:m:mended position for the pu:mp link is in the No.2 hole. Placing the link in the No.3 hole increases the pu:mp stroke and hence increases the accelerating fuel charge to :maxi:mu:m. Placing the link in No. I hole shortens the pu:mp stroke and de creases the accelerating fuel charge to :mini:mu:m, 6. THROTTLE LEVER SPRING. Install spring, being sure loops are securely hooked at spring bracket and throttle lever.
OIST,RIBUTOR BRACEKET
Fig. 68
CARBURETOR FINAL ADJUSTMENT

All adjust:ments :made during asse:m.blyprocedures were preli:minary. Final and accurate adjust :ments can only be :made after carburetor is :mounted on engine.
ADJUSTING GOVERNOR - MODEL 1174

Connect tacho:meter and adjust governorto cut off within the engine no-load cut-off range (see Specifications) as follows: 1. Turn off ignition switch. The engine :must be co:mpletely stopped to adjust this governor. 2. Re:move the adjusting hole located at the side of the housing. (Do not break the nection seal). Re:move the hole plug. (Figs. 68, 69). plug seal governor pipe con adjusting
A8662
Fig. 69
3. Turn engine over with hand crank (ig nition switch OFF) until the adjusting screw in the end of the enclosed rotor appears at the plug hole. 4. Insert a screwdriver through the open ing fro:m which the hole plug was re :moved and turn the screw clockwise
to increase speed or counter-clock wise to decrease engine governed spe~d (Fig. 70). One turn of the screw will affect the governed speed approx i:mately ISO engine r.p.:m.
Fig. 70 CAUTION: Excessive engine speeds cause

undue strains and rapid wear on engine parts,
therefore, the governor :must not be adjusted to
allow the engine to exceed the :maxiInu:m re
co:m:mended r.p.:m.
FUEL SYSTEM Section E Page 1
AIR CLEANERS
Cover retainer nut,
.....__ Mounting bracket
A23444
Fig. I - Air Cleaner (Bonnet type mounting).
Fig. 2 - Air Cleaner (Bracket type mounting),
Description
The construction of the oil-type air cleaner (Figs. 1 and 2) is such that uncleaned air is drawn into the upper portion of the unit and then drawn downward at high velocity. Just above the oil reservoir the direction of air travel is suddenly reversed, and this reversal of air flow causes the larger particles of dirt to fall into the oil. The partially cleaned air then travels upward through an oil moistened filtering ele ment where any remaining dirt and dust par ticles are removed. The cleaned and purified air then leaves the air cleaner and enters the carburetor. The air cleaner on Super Red Diamond En gines is located in the conventional ''under the hood" position. However, the air taken into the air cleaner is drawn through a special hood opening (Fig. 3). The purpose of this outside intake is to draw in cooler outside air during hot-weather operations, when high under-hood temperatures would otherwise make available to the engine only expanded air with low oxygen content. By drawing in cooler air, with greater oxygen volume per cubic foot, volumetric effi ciency is increased and the engine produces the greater horsepower for which it is designed. In cold weather, when under-hood air tem perature is more desirable for efficient engine operation, air intake is easily changed to draw air from under the hood.
Fig. 3
Under normal conditions, oil type air cleaners should be removed and serviced every 5000 miles. The operation should be performed at earlier intervals under dusty operation - even daily, under severe conditions. When servicing the oil type air cleaner, re move, the oil cup. or reservoir, and clean free of old oil and dirt. Wash the filtering mesh, or element, in kerosene then dip in clean oil and allow the excess oil to drain from the element. Air cleaners should be serviced with same grade oil as used in the crankcase, and the oil cup filled to the level indicating beads in the cup. (See chart below for approximate capacities). Air cleaner connections must be maintained in a tight and leak-proof condition. Otherwise, uncleaned air will be allowed to enter the
OIL CAPACITY (PINTS)

-~.~---,--~-------
Servicing Air Cleaners

The necessity for cleaning and servicing of oil type air cleaners depends entirely upon operating conditions as to dust, dirt, etc.
P''HNTEO IN UNITED STATfS OF AMeRICA
BD 269
Cont. R-6602
2-1/2
INSTRUMENTS Index Page 1
INSTRUMENT GROUP
SECTION "A"
Page Eq uipment for checking gauges . . . . . . . . Flexible shaft (tachometer) . . . Fuel gauge operation . . . . . . . General description . Method of checldng gauges Oil pressure gauge operation. Service instructions . . . . Speedometer (and odometer) . . . . Tachometer (repairing and lubricating) Water temperature gauge operation 3
4
1,2
1 3,4
2 1
4
4
2,3
SECTION orB"
Speedometer adapter calculations ......... 1
PRINTEO IN UNITEO STATES OF AMERICA
INSTRUMENTS Section A Page 1
INSTRUMENTS
COMBINATION STARTING AND IGNITION SWITCH
R-ll0 to RF-210 (Delo-Remy No. 111650l)

When the switch key is turned to the left. all accessories and gauges are "ON" except the ignition which is "OFF".. When the switch key is turned half way to the right, the accessories and ignition are both" ON". Turning the ignition switch key to the extreme right will engage the starting switch and complete the electrical circuit between the battery and the starting motor so that the pinion engages the flywheel ring gear and cranks the engine.
ers 12-MARCH 1953 (Supplemental page. for erS-ll).
PRfNTED IN UNITED STATES OF AMERICA,
INSTRUMENTS
Tachometer Fuel Ammeter Speedometer Air Speedometer Ammeter Tachometer
Oil pressure gauge
Temperature gauge
Air pressure gauge

A.22497
Beam indicator light
Temperature gauge
Oil pressure gauge
A.22498
Fig. General Description

Fig. 1 illustrates location of instruments on dash panel. Fig. 2. illustrates the rear view of the same instruments and panel assembly as in Fig. 1. The fuel gauge, oil pressure gauge, and water temperature gauge are electricallyoper ated and consist of a sender and receiver (dash) unit. Diagrams (Figs. 3 to 9 inclusive) illustrate the major parts of each unit and the principle of operation. An optional source of supply of instruments is established at the factory and the new truck may be equipped with instruments that corne to rest in the upper range when the switch is turned to "OFF" position. In these in stances. the details of operation of the unit are similar. The illustrations will apply in either case except for direction of travel after switch is turned to "OFF" position.
Fig. 2
Electrical tachometer Magnetic starting switch Headlight sealed beam unit Headlight dimmer switch Fuel gauge and fuel tank sender unit Oil pressure gauge and engine sender unit Water temperature gauge and engine send er unit CAUTION: Always have ignition switch in "OFF" position when changing or working on instruments to avoid the possibility of a short circuit, which will damage instruments. Both sender and receiver units must be of same type. Do not use a sender unit of one manu facturer with a receiver unit of another, or vice versa.
Fuel Gauge Operation (King-Seeley)

When fuel tank is empty (Fig. 3) the two contacts infuel tank sender unit are just touch ing. With the ignition switch on, current flows through the circuit, warming up the heater wires which causes the bi-metals to bend, and
Service Instructions.
The following units require no adjustment or maintenance other than keeping the elec trical connections tight. Due to the intricate construction no attempt should be made to re pair or calibrate these units. IF UNIT FAIL URE OCCURS, REPLACE WITH A NEW UNIT. However. no unit should be removed until a thorough check has been made of wiring, sender units, condenser, etc. for a short, otherwise, a new unit will also burn out. Coil Ammeter Starter switch Ignition switch Circuit breaker Stop light switch
PFUNTEC IN UNITt:O 'TATES 0,.. AMEI'HCA
Operation with tank empty
Tank sender
A-22943
Fig. 3 - Gas Gauge - Tank Empty.
INSTRU MENTS Section A Page 2

Operation with low oil pressure Bimetal Insulated contad
bending of bi-:metal in tank sender unit opens the contacts and circuit is broken--the heater wire then cools and the bi-:metal returns to its for:mer position. Contact is then again :made and the procedure is repeated at the rate of approxi:mately once per second. Since both heater wires are in the sa:me circuit, a si:milar slight bending of the bi-:metal in the dash receiver unit occurs, which is just sufficient to :make the needle register zero. When tank is filled with gasoline (Fig. 4) the action of the float and Canl pushes the grounded contact against the insulated bi-:metal contact, bending the bi-:metal in the tank sender unit.
I~~~~~~"
It
~ Grounded c o n t i d
Flexible diaphragm Oil pressure S 0

Dash receiver
t'------'
Pressure
plug Ignition switch
III ~
A-23ITS
Fig. 5 - Oi I Pressure Gauge - No Pressure.

Operation with high oil pressure
Operation with tank full
II:~~~~~~ Insulated contact

Grounded contact
Cam Tank sender

A22945
Float
Flexible diaphragm Oil pressure plug
IIII~
A-2294T
Fig. q - Gas Gauge - Tank Full.

Now if the ignition switch is on, the action de scribed in the preceding paragraphs occurs but because the bi-:metal is already under strain a :much greater a:mount of current is required to bend the bi-:metal sufficiently to break contact in this position. A si:milar greater bending of the bi-:metal in the dash receiver unit occurs and this action pulls the needle over to the full point. The :move:ment of the needle in any posi tion caused by the :make-and-break of the cir cuit is so :minute that it can not be detected.
Fig. 6 - Oi I Pressure Gauge - With Pressure.

Note in Fig. 6 that the deflection of the diaphrag:m pushed the grounded contact agains t the insulated bi-:metal contact, bending the bi
:metal in the sender unit.
Water Temperature Gauge Operation
(King-Seeley) The engine sender unit consists of a fixed grounded contact, so positioned that the bi :metal against which it presses is bent :mechan ically. At low te:mperatures (Fig. 7) consider able heat is required to :make this bi-:metal bend away fro:m the grounded contact. With the te:mperature of the engine-cooling water
Oil Pressure Gauge Operation (King-Seeley)

The operation of the oil pres sure gauge sender unit is si:milar to the fuel gauge sender unit except that instead of a ca:m, a diaphrag:m is used as a :means of :moving the grounded contact. The dash receiver units operate ex actly the sa:me. NOTE: Should the oil pressure gauge indicate pressul"e lower than nor:mal, the engine sender unit and dash unit should be checked prior to looking further for the trouble (Fig. 5). In so:me instance low oil pressure reading on the gauge can be corrected by changing the position of the engine unit. This unit is nor:mally asse:mbled with the small depression in the cover at the
Operation with low temperature Insulated contact Bimetal

Bimetal-temperature operated .~ Heater wire Heater wire
~~ ~'; :G=ro~u=nd=e=d"\:t:=on~ a~c; -t
A.22944
-7\.
Water temperature-heat plug
Fig. 7 - Water Temperature Gauge - Cold.

Operation with high temperature
Instrument being tested.
Ignition switch
1/11f-:l..
V
A-22946
A22931
Fig. 9 - Method of checking gauges.

These long lengths will in practically all instances permit individual making check to sit in seat of truck and observe gauge being checked.
Fig. 8 - Water Temperagure Gauge - Hot.

low, all this heat must be generated electri cally, and this same current flowing through the heater wire of the dash r~ceiver creates an equal amount of heat there and a resultant bending of the dash receiver bi-metal, causing the pointer to show a low temperature reading. As the water temperature rises, its heat aids in bending the sender bi-metal--less heat is generated electrically, the resultant bending of the bi-metal in the receiver is less, result ing in higher temperature readings (Fig. 8). The following service instructions apply to fuel level, oil pressure or water tempera ture gauges. IMPORTANT: Do not disconnect instru ments with ignition switch" ON" as there is dan ger of causing a short circuit which will dam age instruments. Always turn ignition switch "OFF" before changing or working on instru ments. NOTE: If it is necessary to replace the receiver unit, because it has been burned out, then check wiring, sender unit, and condenser, if any, for a short, and correct this condition, otherwise, newreceiver unit will also burn out. A short in the gauge circuit is easily rec ognizable because it will cause receiver unit to over-read and in most cases beyond full scale.
Method of CheCking Gauges

(IMPORTANT: No units should be re moved from truck until check has been com pleted which shows such units to be damaged or defective.)
1. Disconnect sender unit being checked and hook in tank unit as shown in Fig. 9. Turn on ignition switch and operate float rod of tank unit by hand. With float of tank unit at bottom position, receiver unit being checked should register at bottom mark on dial. Next, move float rod up to top po.si tion, then receiver unit being checked should move to top mark on dial (allow one minute for receiver to corne to rest).
NOTE: Exceptions to this are the oil pres sure and water temperature gauges. The oil pressure gauge should register at the RUN mark with the float rod at top posi tion. This is the mark just below the top mark on this gauge. The water tempera ture gauge should register at the HOT mark. 2. If receiver unit operates correctly, then check sender unit on truck to see if it is properly grounded. Also (a) if truck is radio-equipped check condenser on sender unit. If condenser is shorted, it will cause receiver unit to overread. When replacing condenser, it is preferable to use .one of .10 or .20 micro-farad capacity, but up to .50 can be used if necessary to cut out radio interference. (b) If ground and con denser are satisfactory. then replace sender unit and check to see if this has corrected the difficulty. 3. If receiver does not operate or fails to operate correctly then check wire lead to receiver unit. Do this by attaching one end
Equipment Necessary for Checking Gauges

1. One new fuel tank unit. If there is any ques
tion about the new tank unit being correct, then hook it up in s'eries with a receiver unit known to be satisfactory, and apply 6 volts of current. Operate tank unit by hand and see if receiver unit reads zero with tank unit float in bottom position and full with tank unit float in top position. 2. Two ten-foot lengths of insulated wire equipped with clip terminals at each end.
PRINTEO IN UNI'tP STATES OF AMnHCA

The centrifugal tachometer works on the weight-type governor principle and is driven from the distributor s,haft in the same manner as the magnetic type. The centrifugal type als 0 has a maximum r.p.m. hand on the tachometer head to record maximum speed of engine. The electric tachometer is a two-unit combination consisting of transmitter and tachometer head. The head is mounted on the instrument panel and the transmitter on engine side of dash. The transmitter name plate pro vides a cover for an easily replaceable standard flash-light battery wliich supplies a fixed volt age to guarantee 2% overall accuracy. The current requirement is so small that the bat tery will give a normal service of approximately six months. The electric tachometer receives electrical impulses from the distributor through the transmitter arid records the r.p.m. in this manner.
of a ten-foot length of wire to the terminal of the receiver unit to which sender unit wire was attached. Ground the other end of the ten-foot lead and turn on the ignition switch. If the gauge operates now and did not operate with the regular wire COnnec tion, the wiring is at fault and must be re placed.
If wiring is satisfactory then replace re ceiver unit and check again with tank unit.
Do not attempt the repair or calibration of any receiver or s ending unit in the field as this is not practical. Replacement with a new unit is the only practical means of servicing these gauges.
Speedometer
The speedometers used on L-Line trucks are of the magnetic-type. A speedometer is used on a vehicle to in dicate speed in miles per hour as shown by the pointer on face dial, and to record distance traveled by means of an odometer. The speed ometer is driven through a flexible shaft con nected to a set of gears in the vehicle trans mission. These gears are designed for the particular vehicle model and take into con sideration the tire size and rear axle ratio. The flexible shaft, which connects the trans mission driven gear to the speedometer, con sists of an outer casing and inner core. The odometer usually records up to 99,999 miles before it automatically returns to zero. The extra wheel on the right side of the odom eter is known as the tenth dial, replacing the old type trip odometer, and records every tenth of a mile. There are occasions when, due to change in axle ratios or tire sizes, it is necessary to make compensating corrections in the speed ometer drive gear. For method of speedometer adapter calculations, see following Section "B", Instruments.
Tachometer Flexible Shaft

A complete flexible shaft consists of two major assemblies. A flexible outer casing with nuts and ferrules at both ends and a wire wound flexible inner coil assembly with squared ends or crimped-on tiP'S. The core diameter and end connections vary for different applica tions. One end of the flexible shaft is attached to the instrument (speedometer or tachometer) and the other end is attached to the transmission or power take-off point. The flexible inner core transmits the power from the take-off, while the outer casing is held rigidly in place at each end by the ferrules and nuts.
Repairing Tachometer Flexible Shaft

Disconnect both ends of the shaft and re move from vehicle. Pull the core out of the casing and check for kinks by rolling on a flat surface. If a flat surface is not available, take an end in each hand and roll core between fin gers. In either case a core kink will show up as a "hop" at the kinked point. Never reuse a kinked core, because it will cause fluctuation of the speedometer or tachometer point. Also check for frayed spots by running it loosely through your finger. Do not reuse a frayed core. Kinked or frayed core usually indicates a casing with very sharp bend. CAUTION: Under no circumstances should a casing have less than a six-inch radius bend.
Tachometer
A tachometer is installed on a vehicle to record engine r.p.m. speeds and enables the driver to keep engine within efficient operating range. The magnetic type tachometer is installed at the factory on all Super Red Diamond En gines. It is driven by a flexible shaft connected to the vehicle distributor shaft by means of a drive joint or adapter and records the r.p.m. from the dis tributor shaft onto the face. dial through a magnetic field within the unit. There are two additional types of tachom eters available, namely, centrifugi:d, with a maximum r.p.m. hand, and electrical.
Lubricating Tachometer Flexible Shaft

Thoroughly clean the core and cas ing. Ap ply a thin coat of graphite impregnated non hardening grease evenly over the core ONLY. Hold the casing with one hand and feed the core with lubricant into casing. CAUTION: Never fill or pack the casing with grease. Periodical lubrication of the flexible shaft is recommended to avoid premature failure.
INSTRUMENTS Section B Page 1
METHOD OF SPEEDOMETER ADAPTER CALCULATION

There are occasions when. due to changes in axle ratios, or tire size. it is necessary to make compensating corrections in the speedometer drive. . Parts catalogs list available speedometer adapters and the one chosen should most closely coincide with the calculated results. The following formulae are based on new tire radii when correctly inflated and properly loaded, and should prove helpful in selecting speedometer adapter equipment. Problem Formulae Problem Formulae
(A) Actual distance (D) Old tire rev. per mile *Present Required Err.or in traveled *Present Required Tire size X adapter adapter speed X adapter = adapter has been ratio ratio. ometer Speedometer ratio ratio. changed. New tire rev. per mile reading indication NOTE: If no adapter in present hook *NOTE: If no.adapter in present hook up - disregard in calculations. up - disregard in calculations. EXAMPLE: Old tire rev. per mile (7.00-20): 573 New tire rev. per mile (9.00-20): 525 EXAMPLE: Actual distance traveled: 5 miles *Present adapter ratio: 1.155 6 miles Speedometer reading: Formula is then: Required *Present adapter ratio: 1.200 573 X *1.155 = 1.260 adapter Formula is then: ratio. Required adapter Ir----(E--)---+*-p--r-e-s-e-n-t--a-d-a-p-t-e-r--r-a-t-io--X----------- X *1.200 = .9996 ratio. Required --------/------------------------------------11 Ti re s iz e old ti re rev. per mile X and axle old axle ratio adapter (B) Old axle ratio *Present Required ratio b o t h . . ratio. -----------. X adapter Axle adapter h d New tlre rev. per mlle X New axle raho ratio new axle ratio
c ange . ratio ratio. has been
NOTE: If no adapter n present hook i changed. *NOTE: If no adapter in present hook up - disregard in calculations. up - disregard in calculations. EXAMPLE;
EXAMPLE: Old axle ratio: New axle ratio: *Present adapter ratio: Formula is then: 5.285 X *1.155 = .9909 6.16
5.285-1 6.16-1 1.155 Required adapter ratio.
(c) 10084
To find *Tire rev. (F) Loaded tire radius tire -per mile. To check in inches revoluadapter Hons if ti re
per mile. *Deduct 1'10 for high pressure tires, diameter, or 1-1/2'10 for balloon tires. axle ratio, and NOTE: See CT-350 for tire radius speedspecifications. ometer drive and EXAMPLE: driven Constant figure: 10084 gears are Loaded tire radius of 7.50-20 tire: known. Formula is then: 10084 - - - = 582 17.3 Tire rev. 582 - 1-112'10 = 573 per mile.
*Present adapter ratio: 1.155

Old tire rev. per mile (7.00-20): 573 Old axle ratio: 5.285 New tire rev. pe r mile (9.00-20): 525 New axle ratio; 6.16-1 Formula is then; 1.081 1.155 X 573 X 5, 285 = Required adapter 525 X 6.16 ratio.
Loaded tire radius X 0.1 X

numberteethindrivengear _ Adapter Axle ratio X number teeth ratio.
in drive gear NOTE: See CT-350 specifications. EXAMPLE: Loaded tire radius Constant figure: Number of teeth in driven gear: Axle ratio: Number of teeth in drive gear: Formula is then: 18.9 X 0.1 X 14 6.16 x 4 for tire radius 18.9 0.1 14 6.16-1 speed
4
(9.00-20): speed
1.073 Adapter ratio.
LUBRICATION Index Page 1
LUBRICATION GROUP
INDEX
SECTION "A"
General instructions . . . Air cleaners . . . . .

Chassis ........ ,. . . . . . . .
II
............. .
Page 1
4
3 3
5
Clutch release bearings . . . . . . . . Double-reduction hypoid axles (Eaton) . Engine oil selection. Engine oil types . . Propeller shaft cente r bearings (not prelubricated type) .. Single-speed hypoid axles. . . . . . . . . . . . . . Timken (S-ZOO, U-ZOO, S-300, U-300) hypoid axles . . . Transmissions . . . . . . . . . . Two-speed hypoid axles (Eaton). Unit capacities .. Water pumps . . Wheel bearings . . .
1, 2, 3
4
4
6
3
5 7
3
3
SECTION ItB"
LUBRICATION CHARTS
Truck Series L-110 . L-120 L-130 L-150 . L-160 . L-170 . L-180,L-181,L-182,L-183,L-184. L-190 . L-200 .
PRINTED IN UNITO stATES OF AMRICA
Page 1, 2 3,4 5, 6 7, 8 9, 10
T ruck Series L-Z10. L-ZZO. L-Z30. LM-lZO LM-l50 LF-170. LF-190.
Page
..
..
. .
..
11, 1Z
13, 14 15, 16 17, 18
LF-Z20. .
LF-ZlO.
. .
LUBRICATION Section A Page I
LUBRICATION
NEW SERVICE CLASSIFICATIONS AND DESIGNATIONS FOR LUBRICATING

OILS FOR AUTOMOTIVE TYPE GASOLINE AND DIESEL ENGINES
In the period just prior to World War II, developments in the design of both gasoline and high speed diesel engines and in the services to which they were subjected, resulted in the introduction of new types of crankcase oils. To enable the automotive mariufacturers to recommend these new oils, the American Pe troleum Institute was asked to define them. This was done and the API definitions of oil types designated I!Regular," "Premium" and "Heavy Duty" were published in 1945. Recently, the automotive and petroleum industries have recognized that the definitions just mentioned had limitations. While satis factory when established in 1945, the definitions did not provide for the many new developments since the war in engines or in crankcase oils. To correct this situation, two industry committees worked together; one, the Lubri cation Committee of the American Petroleum Institute representing both large and small refiners and marketers, the other from the American Society of Testing Materials on which the major manufacturers of gasoline engines and high speed diesel engines were repre sented. By this joint effort, a new system of Service Classifications and Designations for Motor Oils for Automotive Type Engines has been developed as a basis for selecting and recommending oils for these engines. The SAE Viscosity Numbering System is in noway affected by the new API Service Clas sification System and will be used as before to indicate the proper viscosity grades of oils for any service. The definitions of service, approved by the API and the supplementary explanations are presented for the information of those who are interested. diesel engines is based primarily on the suit able combination of these five factor s: 1. Engine Design and Construction 2. Fuel 3. Motor Oil 4. Maintenance Practices 5. Operating Conditions To begin with, the design and construction of different engines and consequently their lubrication needs vary widely sinc e individual engine manufacturers place emphasis on dif ferent engine features, Fuels alsovary widely, depending upon the crude oil and refining methods used. Motor oil characteristics and performance depend not only upon crude source and refining methods. but on the special ingre dients which may be added to oils 'in their manufacture. As for the maintenance of en gines, naturally it varies from good to poor. The service conditions under which en gines operate are extremely wide and have a major influence upon the character of oil re quired to give the best performance for any particular, combination of engine design and kind of fuel. To provide a workable guide for the selec- Hon of oils suited to various engine designs, service conditions had to be divided into broad classes, based on the most up-to-date knowl edge and experience. Obviously, it was impos sible to define and include all possible service conditions and it was actually unnecessary because an engine may be operated in a variety of services in any given period. In the new system, the various classes of service for gaSOline and diesel engines are defined and explained. Quite important is the fact that some types of service commonly thought of in the past as being very light are actually quite severe from the lubrication standpoint. This applies especially to passen ger car s and light trucks. Each service class is designated by let ters. This provides a convenient means where by oil companies may indicate what class or classes of service each of their several brands of oil are suitable for. The engine manufac turer may similarly use these letter designa tions to indicate the service and lubrication requirements of his various engine designs,
PRfNTItO CN UN1TitO STATES OF ... MERIC.....
BASIS OF THE NEW SERVICE

CLASSIFICATIONS
In devising the new Service Classification System, it was recognized that the satisfactory operation of automotive gasoline and high speed
crs 12-MARCH 1953 (Supplemental pages for crs.ll),
LUBRICA TION
Section A Page 2

Service MM
III
DEFINITIONS AND EXPLANATION OF SERVICE CLASSIFICATIONS

The new Service Classification System includes five types of service, tn1"'ee for gaso line engines, two for diesel engines. Each service type is defined and explained below and the corresponding letter designations shown.
Service typical of gasoline and other spark ignition engines operating under moderate to severe service conditions, but presenting problems of deposit or bearing corrosion con trol when crankcase oil temperatures are high. This is a more moderate service condition than Service MS. Vehicles powered by engines which are relatively insensitive to deposit formation when operated at high speeds and under heavy loads ar e included in this service, particularly when operated with fuels of suit able characteristics. It does not include ex tensive operation under the severe type of low engine temperature service such as start and stop driving or prolonged idling described under Service' MS.
GASOLINE AUTOMOTIVE TYPE ENGINES
Service MS
Service typical of gasoline or other spark ignition engines operating under unfavorable or severe types of service conditions, and where there are special lubrication require mep.ts for deposit or bearing corrosion con trol, due to operating conditions or to fuel or to engine design characteristics. Service MS normally represents the most severe service conditions encountered in the operation of gasoline and other spark ignition engines. It includes two different types of severe or adverse operating conditions which are as follows: Start and stop service promotes condensa tion in engine cylinders and crankcases of water from fuel combustion and also dilution of the oil with unburned fuel; it can promote corrosive wear of cylinders, pistons and rings, also oil ring plugging, varnish deposits and low temperature emulsion type sludge. In pas senger cars and other unit's the severity of this service increases in wintertime as atmospheric temperatures drop, although it is often a year round problem in taxicabs, delivery trucks and similar operations. The nature of the fuel can influence these troubles. The design of the cooling system and the effectiveness of crank case ventilation can increase or decrease their severity. High temperature, severe service pro motes oxidation of the lubricating oil. This type of service may cause high temperature varnish and sludge deposits, stuck rings, and scuffing of rings inall types of engines. It may also cause corrosion of some types of bearings. This condition is aggravated by driving long distances at high speed, particularly in hot weather. Under these conditions, the crank case oil is subjected to relatively high tem peratures. The nature of the fuel may have some influence on the severity of this condi tion, but its relative influence is less under these high engine temperatures than under start and stop conditions. Engine design, es pecially adequate cooling of oil as well as of pistons, valve guides, and seats, can minimize the effect on the oil.
Service ML
Service typical of gasoline and other spark ignition engines operating under light and fa vorable service conditions, the engines having no special lubrication requirements and having no design characteristics sensitive to deposit formation. This is the least severe service condition. This type of service includes moderate speed driving most of the time, with no severe low or high engine temperature operation. It also in cludes operation of vehicles with engines in sensitive to sludge, deposit formation or fuel characteriestics.
DIESEL AUTOMOTIVE TYPE ENGINES

The severity of diesel engine service with respect to wear and deposit formation depends upon a combination of several factors. First is the power requirement. High continuous power output or overload at high atmospheric temperatures or intermittent power demands at low temperatures represent severe service. By contrast, rated load, continuous or inter mittent operation at normal temperatures can be considered normal diesel engine service. From the standpoint of design, diesel en gine speeds are usually lower than gasoline engine speeds but higher temperatures within the engine and greater bearing loads may be expected. The design of the engine and its cooling system, also its installation in any equipment all affect service severity. In the diesel engine. harmful products of combustion causing wear and deposits on pistons and in the crankcase can be forme d from incomplete combustion of any fuel and from some specific fuel components such as

sulphur. The effects of these combustion products and consequently the severity of the service requirements are greatly magnified by low temperature operation and are influenced in varying degree by engine design character istics.
LUBRICA TION Section A Page 3
CLUTCH RELEASE SLEEVE AND BEARING LUBRICATION

Clutch release bearing sleeves on all R-line chassis incorporate a lubricator fitting to provide means of lubricating the clutch re lease bearing, sleeve and fork without their removal from chassis. R-110 through R-184 chassis have the clutch release sleeve and bearing lubricator fitting located at the bottom of the release bearing sleeve, as illustrated in figure 1. Access to this fitting is gained by removal of the flywheel housing bottom cover.
Service DG
Service typical of diesel engines in any operation where there are no exceptionally severe requirements for wear or deposit con trol due to fuel or to engine design character istics. Rated load. continuous output or intermit tent operation under normal temperature con ditions can be considered as normal service requirements for service DG. Depending upon individual engine design characteristics, most diesel engine builders have designated maxi mum fuel sulphur limits for this service clas sification.
Service DS
Service typical of Diesel engines operating under extremely severe conditions or having design characteristics or using fuel tending to produce abnormal wear or deposits. The service donditions in this classifica tion are the most severe encountered in the operation of diesel engines. High load opera tion at high temperatures, design factors or engine installation details causing high temper atures within the engine, constitute severe service. as does intermittent operation at low temperatures since both promote wear and deposit formation. Cooling system design and maintenance practices can aggravate or mini mize the severity in either case. The use of high sulphur content fuels increases service severity with respect to wear and deposits in varying degree. depending upon design, main tenance and operating conditions, especially low . temperatures. Hence, frequently their use is considered to constitute severe service.
1
) ,
LUBRICATOR
A30485
Fig. 1
Release Bearing, Sleeve and

Lubricator
USE OF LETTER DESIGNATIONS

When the letter deSignations are used to indicate services for which oils may be suit able. it is the intent that they be preceded by the words. IIFor Service." To illustrate, an oil suitable for moderate service conditions in gasoline engines would be referred to as "For Service MM." If oils are suitable for more than one service, it is appropriate that these oils be referred to with the marks associated with such services. For example. "For Serv ices MS--DG or MS--MM." etc.
R-185 through RF-ZlO chassis have the clutch release sleeve and bearing lubricator fitting on the top of the release bearing sleeve (not illustrated). Access to this fitting is gained by removal of the cab floor mat, cab floor transmission cover plate and clutch bell housing inspection plate. To lubricate. use a low-pressure hand operated grease gun filled with a suitable lu bricant comparable to "Lubriplate No. 110", fill lubricant cavity in release sleeve and bear ing. DO NOT OVER-LUBRICATE. Lubricate every 15,000 to 20,000 miles under normal operating conditions. Under unusual "Stop and-Go" driving conditions, lubricate every 1 0 ,000 miles.
CTS 12-MARCH 1953 (Supplement.1 page. foc CTS-ll).
PRINTED IN UNITED STATES OF AMERICA..
LUBRICATION Section A Page 1
LUBRICATION
GENERAL INSTRUCTIONS
Thorough lubrication at definite intervals with a good lubricant will aid greatly in pro longing the life of the truck and in the reduction of operating expense. The interval between lu brication periods depends entirely upon oper ating conditions. The loads carried, speed, road and weather conditions all have a bearing on the frequency of lubrication periods. In the lubrication charts, the mileage rec ommendations are approximate, being based on average conditions. For some types of opera tions it will be necessary to figure the lubrica tion periods upon an hourly basis, and where operating conditions are extremely severe, the truck should be lubricated after every twenty four hours of operation. Only lubricants of the best quality, having proper body or viscosity, manufactured by a reputable concern, should be used. We do not attempt to specify any particular manufacturer's products. High-grade lubri cants can he secured from any reputable oil company. The viscosity nlunbers used are those adopted by the Society of Automotive Engineers to classify lubricants according to body or thickness and do not cover any other properties. When changing engine oil, clean and refill air cleaner, also clean oil filter if used. In consideration of the foregoing, the fol lowing general recommendations are made: MODERATE SERVICE--trucks operating in multi-stop or other service where sus tained higher engine speeds will not be encountered: TEMPERATURES 90 0 (F.) 32 0 (F.) +10 0 (F.) +10 0 (F.) to to and to ENGINE 90 0 (F.) 32 0 (F.) _10 0 (F.) up* SD BD RD SAE-30 SAE-30 SAE-20W SAE-lOW SAE-40 SAE-40 SAE-20W SAE-lOW SAE-40 SAE-40 SAE-20W SAE-IOW
I
R-6602 SAE-40 SAE-40 SAE-20W SAE-IOW *See Hot Climate - High Speed instructions below. For temperatures lower than minus 10 0 (F.), use SAE-lOW and kerosene. (SAE-lOW may be safely diluted with colorless kerosene up to 30"10). Mix kerosene thoroughly with the oil before adding to the engine. NOTE: Kero sene will evaporate rapidly under crankcase operating temperatures. Because of this fact, more fre uent checkin of the oil level must e made to aVOl operating the engine with low oil level.
ENGINE OIL SELECTION

Selection of proper engine lubricating oil demands consideration of two important fac tors--namely, easy starting during very cold weather, and adequate engine lubrication after the engine is placed in service. Lighter viscosity oils facilitate cold weather starting and also provide better iIIlIIlediate lubrication as the engine starts. CAUTION: They do not, however, provide ad equate lubrication under sustained higher en gine speeds or severe service. Increased oil consumptIon can also be expected when using lighter viscosity oils. Frequent oil level check must be made when using lighterviscosityoils. Consideration must therefore be accorded to the cold weather housing facilities for the idle truck, the service in which the truck is engaged, and the selection of higher viscosity oils which have better free-pouring character istics at low temperatures.
PRINTED IN UNITO STATES OF AMERICA
Hot Climate - High Speed

For trucks operating on highway, or other services demanding sustained higher engine speeds, use engine lubricating oils having a viscosity of as near SAE-50 as possible (SAE 40 for SD Engines) in keeping with the starting ability. NOTE: High viscosity oils are avail able which also have very good cold pour char acteri stics.
ENGINE OIL TYPES

Engine oils are available either as "straight" mineral oil (having nothing added during its manufacture other than possibly a pour-point depressor), or as lIa dditive" oils which have had certain cheIIlicals added during manufac ture for the purpose of providing qualities or properties not available in the original oil, either before or after refining.

(3) POUR-POINT DEPRESSANTS; Because mineral oils thicken or congeal at low tem peratures, certain chemicals are added to "additive" oils to serve as pour-p~int de pressants or, in other words, to lower or depress the pour point a few degrees. The result is an oil having better flow charac teristics at low temperatures which will provide better immediate lubrication upon starting during cold weather because of the fluid state of the oil. The use of the prop er engine oil is of utmost importance in obtaining maximum performance and satis faction. The selection of the proper brand of oil should be based on the reputation of the refiner or marketer.
The American Petroleum Institute and the automotive manufacturers have agreed that en gine oils shall now be marketed under three classifications or categories, namely, "Regular Oil," "Premium Oil," and "Heavy-Duty Oil." These are more fully defined as follows: REGULAR MOTOR OIL: This term shall be used to designate a straight mineral oil. Oils of this type are generally suitable for use in internal-combustion engines under moderate operating conditions. (These oils may and often do contain pour-point depressants.) PREMIUM MOTOR OIL: This term shall be used to designate an oil having oxidation stability and bearing corrosion preventive prop erties. Oils of this type are generally suitable for use in internal-combustion engines where operating conditions are such that regular oils do not give satisfactory service. HEA VY -DUTY MOTOR OIL: This term shall designate an oil having proved oxidation stability, bearing corrosion preventive proper ties, and detergent-dispersant characteristics. Oils of this type are generally suitable for use in both high-speed Diesel and gasoline engines under heavy-duty service conditions. Heavy-Duty Oil, if installed in an engine where other-type oils have been used, requires that precautionary measures be taken to pre vent loosened particles from clogging oil passages. The following measures represent good, practical advice when changing from any brand of oil to another: 1. Drain and flush engine crankcase. 2. Iz{stallnewoilfiltercartrid eandthorou h ly clean oil filter sump. Note: Only ab sorbent type or edge type (filter disc) filter packs should be used with detergent type oils. Clay or chemically treated filters should not be used as they will remove some of the beneficial additives used in the manufacture of the oil.)
Under operating conditions, oils tend to undergo chemical changes due to oxidation and form such nonlubricating products as varnish, lacquer, and carbon. Where formation of these undesirable products is excessive when using untreated oils, use of an additive oil may prove beneficial since, through the additive chemicals, formation of those deposits may be minimized or retarded. "Additive" engine oi.ls are those to which chemicals have been added to alter or modify the characteristics of the oil and are generally referred to as "inhibited" oils or as "detergent" oils. An "inhibited" oil is not necessarily a "detergent" oil. Additive oils having both in hibiting and detergent qualities are classed as "Heavy-Duty Oils." The matching of chemical additives to a base oil is carried out in exten sive laboratory engine tests. (Note: The re finers' choice of the base stock to be treated with modern additives is very important. An inferior base oil cannot be transformed into an acceptable oil merely by the use of additives. Not all base oils are equally susceptible to im provement with a given additive, and not all additives are equally effective in the same base oil.) Additives to engine oils generally serve as
(l) corrosion inhibitors or anti-oxidants, (2) as

detergents, (3) as pour-point depressants. More fully, these agents are described as follows: (I) CORROSION INHIBITORS OR ANTI-OXI DANTS; Some of the products of oil or fuel oxidation are corrosive in nature and attack certain of the engine metals such as hard alloy bearings, causing pitting or etching. Engine deposits such as sludge and lacquer result in part from oil oxida tion products. Anti-oxidants impart in great degree resistance to corrosion and sludge formation by controlling oil oxida tion. (2) DETERGENTS (DISPERSANTS). Chemi cals are added which serve as mild clean ing agents and, as such, tend to clean or wash away lacquer and sludge deposits from pistons, side walls, bearing surfaces, and other interior working surfaces of an engine. The detergent action is the result of the ability of the oil to keep insoluble particles--the products of fuel combustion and oil decomposition--in a finely divided state so that they can be kept in suspension in t:Q.e oil. Unless these particles are car ried in suspension or filtered out, they tend to deposit in piston ring grooves and on other engine interior parts. The detergent dispersive action is not effective with par ticles of metal, other abrasives, or coarse carbonaceous material.

3. It is very important that engine operating temperatures be maintained at an efficient level of 160-lBOo F. to reduce the possi bility of excessive sludge formation. Certain precautionary measures must also be observed after the detergent type oil is placed in service: 1. THE ORIGINAL FILL should be drained after 300-500 miles operation, and the oil filter should be servic.ed. In new or recon ditioned engines this is necessary in order to remove possible abrasives. In other engines, where other-type oils have pre viously been used, the washing or detergent action of the heavy-duty type oil tends to loosen deposits which, if not removed by draining, may clog the oil pump screen and oil channels. 2. THE SECOND FILL should not be used in excess of 1000 miles operation and the oil filter again should be serviced. (Note: If necessary, as judged by the condition of the oil, change at an earlier period.)
CHASSIS
When greasing the chassis, it is good prac tice to force lubricant into the bearings until all old lubricant is forced out and the new ap pears. This will flush out any loose dirt or abrasives that may have accumulated and will also assure thorough greasing. A high-grade viscous chassis lubricant will, except in extreme cases, be satisfactory for year-around use. If gear oil is used to lu bricate chassis, SAE-140 is the proper viscos ity.
WATER PUMPS
SD engine water pumps are lubricated at assembly and no further lubrication is neces sary.
BD and RD engine water pumps should be packed with medium short fiber wheel bearing grease at time of overhaul. Pumps should be periodically (10,000 miles) lubricated. Remove lubricant plug, fill housing using a low-pressure lubricant gun.
3. THE THIRD FILL will generally serve for the regularly established drain period. (Note: Color can not be the basis on which oil changes are made; rather, the oil should be changed at periods previously estab lished or as recommended by the oil man ufacturer. 4. If an engine previously operated on either Regular or Premium-type oils (not Heavy Duty) had a bad varnish condition, the use of Heavy-Duty Oil, because of its detergent quality, may dissolve some of the varnish and increase running clearances, resulting in an increase in engine noise and a lower ing or loss of oil pressure. Should this occur, the cause should be determined and the necessary corrections made to restore the oil pressure.
WHEEL BEARINGS
Wheel bearings should be carefully lubri cated. If too much grease is used there will be the possibility of brake linings becoming soaked. Rear axle shaft bearings and the cavity in which they are assembled in the L-IIO Series trucks are properly lubricated at time of assem bly. Pipe plugs are installed in the lubricant fitting holes. It is intended that at 10,000 miles these plugs should be removed, lub ricantfittings installed, the bearings lubricated, and the plugs again installed. Lubricant fittings should not be allowed to remain in place for they may prove an invita tion to overlubricate the bearings. The cavity containing the bearing holds approximately one ounce or two cubic inches of lubricant. NOTE: Excess lubrication will result in damaged oil seals and grease accumulating on brake linings.
TRANSMISSIONS
When possible, always drain transmission when truck has come in from a run. With the oil warm a more thorough draining job can be done, especially in cold weather. To drain, unscrew plug at bottom of case and allow suf ficient time for all the old oil to run out. Be fore refilling, flush with light engine oil or light flushing oil, followed by complete drain ing; this will remove thickened material within the case. Use SCL, EP gear oil or muiti purpose gear lubricant.
CLUTCH RELEASE BEARINGS

The clutch release bearing used in Inter national Motor Trucks, is of prelubricated type and should require no further attention.
LUBRICATION Section A 4

IMPORTANT: NEVER ADD LUBRICANT TO SINGLE-SPEED HYPOID AXLES, UNLESS IT IS THE SAME MAKE AND GRADE AS THA T WHICH IS ALREADY IN THE AXLES. IF THE SAME MAKE AND GRADE L UBRI CANT IS NOT AVAILABLE, DRAIN, FLUSH, AND REFILL WITH LUBRICANT AS PER FOLLOWING INSTRUCTIONS: Draining should preferably be done when truck has corne in from a run in order that the oil may be well agitated and warmed up. This is particularly desirable in cold weather. To drain, unscrew plug at bottom of hous ing and allow sufficient time for all the old oil to run out. Before refilling, we suggest thor ough flushing with light engine oil or light flushing oil, followed by complete draining, This will insure removal of any thickened material within the housing. NOTE: Use SCL, EP gear oil or multi-pur pose gear lubricant suitable for hypoid axles and supplied by a reputable refinery. Use SAE-90 for cold climate and SAE-140 for warm climate.
PROPELLER SHAFT CENTER BEARINGS

(NOT PRE-LUBRICATED TYPE)
Propeller shaft center bearing should not be lubricated with gear oil or chassis lubricant. Use a medium, short-fibre wheel bearing grease, the technical specifications of which are--cold-milled sodium soap--not calcium- content with a work penetration consistency of 250 that will not break down below 300.
Am CLEANERS (OIL-TYPE)
The cleaning and servicing of oil type air cleaners depends upon operating condj,tions as to dust, dirt, etc. Under normal conditions, oil type air cleaners should be removed and serviced every 5000 miles and at earlier intervals under dusty operations--even daily, under severe conditions. When servicing, remove the oil cup, or reservoir, and clean out old oil and dirt. Wash the filtering mesh, or element, in kerosene then dip in clean oil and allow the excess oil to drain from the element. Use same grade oil as used in the crankcase, and fill cup to the "oil level" indicating beads in the cup. Air cleaner connections must be maintained in a tight and leak-proof condition; otherwise, uncleaned air will get into the engine.
SINGLE-SPEED HYPOID AXLES

(EATON ONLY)
Hypoid gear lubricants have been developed primarily for the differential gear case. The lubricant is intended to provide protection against heavy loads and the sliding action char acteristic of hypoid ring and pinion gears. Use a hypoid gear lubricant available as Elco Gear Safety "28" or its equivalent. A number of hy poid lubricants are prepared by reputable com panies which contain Elco additive concentrates. Viscosity of the hypoid lubricant should be SAE-90. When high atmospheric temperatures (above 100 0 F.) prevail, SAE-140 may be used.
SINGLE-SPEED HYPOID AXLES (NOT EATON)

Hypoid gearing in these axles requires the use of lubricants with properties enabling them to withstand the higher unit pressures and slid ing action characteristic of this type gearing. The mileage figures, relative to the fre quency of lubrication changes, are based upon average vehicle operating conditions, and are not applicable in all cases. The actual condi tions under which the vehicle is operated should be the determining factor in establishing lubri cation requirements. Changes to the correct grade of lubricant for Winter or Summer operations are dependent upon climatic conditions and should be made as requi red regardless of mileage. For average opera tion, check the lubricant leyel every 1,000 miles and drain and refill to level of tapped filler hole every 10,000 miles. To further assure complete lubrication after overhaul, and before the vehicle is placed into heavy slow-speed operation, jack up both rear wheels and run the axle for a short period at speeds equivalent to 25 to 30 m.p.h. Do not allow the wheel on one side to race faster than the wheel on the opposite side.
Check Lubricant Level

Every 1,000 miles, remove filler plug in housing cover and add sufficient lubricant to bring level to filler opening. Install and tighten plug.
Drain and Refill

Every 10,000 miles (see following note) l'emove housing cover lower screw or plug at bottom of housing and drain lubricant. Drain when unit is hot, preferably immediately after operation. Fill until lubricant level is up to filler opening. Install and tighten plug. NOTE: The service intervals between lu bricant drain periods must always be based upon type of service in which the unit is oper ated. Rough and unimproved highway operations as well as heavy loads and off-highway opera tions require more frequent lubricant changes. Sustained high speed and high temperatures

also cause rapid deterioration of the lubricant. Regularly established lubricant change periods should be observed, based upon operation con ditions.
DOUBLE-REDUCTION HYPOID AXLES

(EATON)
Hypoid gearing in these axles requires the use of lubricants with properties enabling them to withstand the higher unit pressures and sliding action characteristic of this type gearing.
TWO-SPEED HYPOID AXLES (EATON)

Hypoid gearing in these axles requires the use of lubricants with properties enabling them to withstand the higher unit pressures and sliding action characteristic of this type gearing. The mileage figures, relative to the fre quency of lubrication changes, are based upon average vehicle operating conditions, and are not applicable in all cases. The actual condi tions under which the vehicle is operated should be the determining factor in establishing lubri cation requirements. Changes to the correct gr<ilde of lubricant for Winter or Summer operations are dependent upon climatic conditions and should be made as required regardless of mileage. For average operation, check the lubricant level every 1,000 miles and drain and refill to level of tapped filler hole every 10,000 miles. To further assure complete lubrication after overhaul and before the vehicle is placed into heavy slow speed operation; jack up both rear wheels and run the axle for a short period at speeds equivalent to 25 to 30 m.p.h. Do not allow the wheel on one side to race faster than the wheel on the opposite side.
The mileage figures, relative to the fre quencyof lubrication changes, are based upon average vehicle operating conditions, and are not applicable in all cases. The actual condi tions under which the vehicle is operated should be the determining factor in establishing lubri cation requirements. Changes to the correct grade of lubricant for Winter or Summer operations are dependent upon climatic conditions and should be made as required regardless of mileage. For average operation,check the lubricant level every 1,000 miles and drain and refill to level of tapped filler hole every 10,000 miles.
To further assure complete lubrication after overhaul and before the vehicle is placed into heavy slow speed operations: jack up both rear wheels and run the axle for a short period at speeds equivalent to 25 to 30 m.p.h. Do not allow the wheel on one side to race faster than the wheel on the opposite side.
IMPORTANT:-NEVER ADD LUBRICANT TO TWO-SPEED HYPOID AXLES UNLESS IT IS THE SAME MAKE AND GRADE AS THAT WHICH IS ALREADY IN THE AXLES. IF THE SAME AMKE AND GRADE LUBRICANT IS NOT AVAILABLE, DRAIN, FLUSH, AND RE FILL WITH LUBRICANT AS PER FOLLOWING INSTRUCTIONS:
IMPOR T ANT: NEVER ADD LUBRICANT TO DOUBLE-REDUC TION HYPOID AXLES UNLESS IT IS THE SAME MAKE AND GRADE AS THAT WHICH IS ALREADY IN THE AXLES. IF THE SAME MAKE AND GRADE LUBRICANT IS NOT AVAILABLE, DRAIN, FLUSH, AND REFILL WITH LUBRICANT AS PER FOLLOWING INSTRUCTIONS:
Fill axle through back filler plug until oil flows from overflow plug. Insert plug. Then add one additional pint of oil using filler hole at top of carrier. This will supply the extra oil required to fill differential and planetary unit. At 1,000 mile intervals, check level of oil in housing.
Fill axle through back filler plug until oil flows from overflow plug. Insert plug. Then add one additional pint of oil using fil ler hole in pinion cage. This will supply the extra oil required to fill differential and planetary unit. At 1,000 mile intervals, check level of oil in housing and add make-up if needed.
NOTE: Use a hypoid gear lubricant avail able as Elco Gear Safety "28" or its equivalent. A number of hypoid lubricants are prepared by reputable companies which contain Elco additive concentrates. Viscosity of the hypoid lubricant should be SAE-90. When high atmos pheric temperatures (above 100 0 F.) prevail, SAE-140 should be used.
PRINTED IN UNITED STATES OF A"'ERICA
NOTE: Use a hypoid gear lubricant avail able as Elco Gear Safety "28" or its equivalent. A number of hypoid lubricants are prepared by reputable companies which contain Elco additive concentrates. Viscosity of the hypoid lubricant should be SAE-90. When high atmos pheric temperatures (above 100 F.) prevail, SAE-140 should be used.
TIMKEN (5-200, U-200, 5-300, U-300) AXLES

Hypoid gearing in these axles requires the use of lubricants withproperties enabling them to withstand the higher unit pressures and slid ing action characteristic of this type gearing. The mileage figures, relative to the fre quencyof lubrication changes, are based upon average vehicle operating conditions, and are not applicable in all cases. The actual condi tions, under which the vehicle is operated should be the determining factor in establishing lubri cation requirements. Changes to the correct grade of lubricant for Winter or Summer operations are dependent upon climatic conditions and should be made as required regardless of mileage. For average operation, check the lubricant level every 1,000 miles and drain and refill to level of tapped filler hole every 10,000 miles. Where an axle has been out of use for a long period, or has been overhauled the lubri cant plug on the top of the Hypoid pinion cage should be removed and one pint of lubricant inserted. This provides immediate lubrication for the pinion before oil is thrown up from the axle housing bowl. To further assure complete lubrication after overhaul and before the vehi cle is placed into heavy slow speed operation: jack up both rear wheels and run the axle for a short period at speeds equivalent to 25 to 30 m.p.h. Do not allow the wheel on one side to race faster than the wheel on the opposite side. IMPORTANT: NEVER ADD LUBRICANT TO TIMKIN HYPOID AXLES UNLESS IT IS THE SAME MAKE AND GRADE AS THAT WHICH IS ALREADY IN THE AXLES. IF THE SAME MAKE AND. GRADE LUBRICANT IS NOT AVAILABLE, DRAIN, FLUSH, AND RE FILL WITH LUBRICANT AS FOLLOWS: NOTE: Use SCL, EP gear oil or multi purpose gear lubricant suitable for hypoid axles and supplied by a reputable refinery. Use SAE-90 for cold climate and SAE-140 for warm climate.
REAR AXLE LUBRICATION CAPACITIES
IH MODEL R-I060 R-I070 R-1165 R-1l70 R-1440 RF-1475 R-1470 R-1530 R-1540 R-1555 RF-1575 R-1630 R-1640 RF-1670 R-1731 R-1741 R-1810 R-2465 R-2466 R-2470
CODE NUMBER 1401 1402 1433 1403 1404 1428 1405 1406 1415 1407 1429 1408 1416 1430 1419 1409 1420 1410 1411 1425 1426 1413 1412 1427 1414 1422 1423
AXLE TYPE Single- Reduction . . . . . . . . . . . . . . . . . . . Single-Reduction . . . . . . . . . . . . Single-Reduction . . . . . . . ... Single-Reduction. . ............. Single-Reduction ........... Single-Reduction . . . . . . . . . , . Single-Reduction .. , . . , , ... Single-Reduction . , . . . . .. Double-Reduction - Eaton . . ... Single-Reduction .. Single-Reduction . , . . ... Single-Reduction . . . . . . . . . . . .... , . Double-Reduction. . . . . . . .. Single-Reduction . . . . . , . . ...
Double-Reduction - S-200 . . .. Single- Reduction . . . . . . . , . . . .
Double-Reduction - U-200 . . . Two-Speed . . . . . . . . . . . . . . , .... Two-Speed . Two-Speed with Timken Diff. , . , .... Two-Speed with Timken Diff. . . . . . . Two-Speed . . . . . . . . . . . . . . Two-Speed . . . Two-Speed with Timken Diff. . .
Two-Speed . . . . . . Two-Speed - S-300 . . . . . Two-Speed - U-300 . . . . . . . . . . . '1
0 0
0 0 ,
CAPACITY (PINTS) 4 Pts. 4 Pts. 4 Pts. 3 Pts. 8 Pts. Each Axle 8 Pts. 8 Pts. 11 Pts. 19 Pts. 20 Pts. Each Axle 11 Pts.
18 Pts.
19 Pts.
38 Pts.
38 Pts.
13 Pts. 13 Pts. 22 Pts.
20 Pts. 22 Pts.
37 Pts.
37 Pts.
R-2475
R-2580 R-2585 R-2590 R-2600 R-2741 R-2800
TRANSMISSION LUBRICATION CAPACITIES

IH MODEL HDS H-41-B T-87-D T-98 T-98 F-51 F-51-C F-52 F-52-C F-54 F-54-B F-55 F-55-B CODE NUMBER 1301 1320 1302 1303 1304 1307 1308 1309 1310 1311 1312 1313 1314 3-Speed 4-Speed 3-Speed 4-Speed 4-Speed 5-Speed 5-Speed 5-Speed 5-Speed 5-Speed 5-Speed 5-Speed 5-Speed TRANSMISSION TYPE CAPACITY (PINTS) 3 5 6 8 8 12 12 19 19 24 24 26 26 Pts. Pts. Pts. Pts. Pts. Pts. Pts. Pts. Pts. Pts. Pts. Pts. Pts.
. - O.D. Transmission - Direct-in-Fifth .

- O.D.Transmission ..
0
... . . . . .
,
Direct-in-Fifth O.D.Transmission Direct-in-Fifth OoD.Transmission Direct-in-Fifth
. . . .

0 0 0
. .
0 0
Code numbers are shown on vehicle specification card L-160 trucks and up.
PRINTED IN UNITED StATES Of' AMERICA
LUBRICATION Section B Page 1
LUBRICATION CHART
L-110 SERIES TRUCKS
(SEE PAGE 2 FOR INSTRUCTIONS)
Front spring front and rear pins (No lub. req'd) (9) Drag link (10)-_
Engine oil filler (3h '\ (13h

, "
""~teering gear
Water pump \.. (No lub. req'd) 7)

I
""
'rt==:;7ft~=:.:;:~ ,I
/1
/1
if
/Generator
J Battery
I
I
(11)
(4)
/
Air cleaner (6)
Engine oil (2)-_ -'--------filter -------~--QDrag link (10)----
-----==1:'[::-:"-J (16)- -
~ol / / /
00
I I " " //
;"..
;:Pi"
_
_""..---
~ ...--Carburetor (14)
linkage
Front wheel bearings (Both sides) Steering knuckles (8) (Both sides) Tie rod ends (Both sides) Distributor
--
".. __ -.//{/,//jl1't:=="..::f
@
I
. .\- ____ . /
//<I'I'
/
U
,/
------Starting motor
..... ---
(ll)
(13)
(10)-- ----_./
/I' ,/I'
/
/I'
/
//
//
//
//
(12)-(10)--
---"
//
/
/
/ /
/
/
/
// I
I
I
,~/I
/ /
Shifting bracket
...J
J
/
/
/
/
/
/ I /
/ /
1 /
/ // II'b/ C~=-1l __ -------UUlversal Jomt

/
/
//
Master cylinder (5)---Shifting bellcrank
//
1// /1
/1tJ'r:z
/
1 I /.
10
r.!
Transmission
/J"'>'\ __ ""Parking brake linkage

'" -.--;.-'"
._--------
(14)
(18) (15)
- - I J-.- ~ - - ..... -tJ
(10)---.../
1/
1:/ ///
/ /
//
"../
,/
/F=-~
-------U
1--' -------
//
/
"
---Slip joint Universal joint Differential
"..--
(I8)
(l3)
Clutch and brake pedal
(10)/ /:/
,/
Clutch release fork shaft(8)--.l/ Center bearing (7)-(No lub. req'd)
vi/
__ ...//1/
/~
Parking brake linkage (14)-...J' Rear wheel bearings (Both sides) Door hinge
(17)-----""/
L-
()
14 ----
--..-'-------l~
----T'-b-q
Door ~anelO
.-J-kn-------
Door latch regulator
(14) (19)
Rear spring front and rear pins (No lub. req'd)
(9)---11
~---~JS:~___
. -- -Wmdow
A-23656
Lubrication periods provide an excellent opportunity to inspect and check for maintenance service that may be needed. Early attention to minor service needs at this inspection will usually prevent serious breakdown later.
PRINTED IN UNliO STATES OF' AMRICA
LUBRICATION
Section B
Page 2
LUBRICATION CHART INSTRUCTIONS

L-ll0 SERIES TRUCKS
I, Engine: Keep crankcase filled to correct level with high-grade engine oil. Changing oil regularly will remove accumulated dirt, Cold weather requires frequent oil change because of increased use of choke, also condensation of moisture~ Refill capacity, 7 quarts; add 1 quart for oil filter. For trucks in multi-stop, or other services where sustained high engine speeds are not encountered, select oil grade as follows: TEMPERATURES OIL GRADE '" 90 (F.J and SAE-40 0 (F.) to 90 32 (F.) . . . , . . . . . . ,. SAE-40 (* See Hot Climate - High Speed instruction following)
UJ' ' , . . . . . .
TEMPERATURES 10 0 (F.) to 32 0 (F.) (above zero) 0 (F.J to Minus 10 10 (F.) above Zero, . , . . .
OIL GRADE SAE-ZOW SAE-IOW
Tem eratures lower than minus 10 F. below zero, us e SAE-IOW plus kerosene, SAE-IOW may be safely diluted with color ess erosene up to 0 percent; mix thoroug y efore adding to engine, and check oil level OFTEN - because kerosene evaporates rapidly at crankcase temperature. Hot Climate'" High Speed: For trucks operating on highway, or other service demanding sustained high engine speeds, use engine oil having a viscosity as near SAE-40 as possible and as starting ability will permit. Note: High viscosity oils are available which also have very good cold-pour characteristics. PERIODIC ALL Y
2.
E' nglne
'I f'lt
01 1
er:
{Change cartridge when oil has darkened, Remove filter cover and cartridge, clean inside of filter - install new cartridge. Run engine for a few minutes and check filter for leaks.
3. Engine oil filler: Remove filler cap, clean element, and dip in engine oil - then drain and replace.
4. Battery: Check water level. If necessary, add pure distilled water to 3/8 inch above plates, Do not overfill.
S,
k t I' d {CheCk fluid level, Do not allow dirt to enter. If necessary, fill to 3/4 inch from top with a high grade autora e mas er cy In er: motive type brake fluid, Do not overfill,
A' 1 {Remove filter element and wash in kerosene. Clean oil sump and refill to indicated level with clean engine oil, same lr c eaner: grade used in crankcase. Further lubrication not required,
7. pWaterlPlumPh: it t b . }Lubricated at factory. rope er s a cen er earlng!
500 TO 1,000 MILES 8, Steering knuckles~ }use a viscous chassis lubricant or SAE-140 gear Clutch release fork shaft: ure of brake and clutch lining.
oil~ Do not over-lubricate ... too much oil will cause fail ...
9. Spring pins: Pins are rubber mounted; lubrication not required.

10. Drag link; tie rod ends: } Shifting bracket: Force a viscous chassis lubricant or SAE-140 gear oil into fittings until old lubricant, dirt, and water are
Shifting bellcrank: expelled.
Clutch and brake pedals:
11. SGtenet:ator: t }put 10 to 20 drops light engine oHin each cup. Do not over-lubricate. ar Ing mo or: Put one drop of light oil on movable contact arm pivot pin. Remove rotor and put two or three drops of light engine oil 12, D' t 'b t . on felt wick. Apply a light coat of vaseline to distributor cam and contact arm fiber rubbing block. Note: Lubricate IS Tl U or. distributor shaft at overhaul or at 25,OOO-mile intervals. Use SAE-20 engine oil. Use sealing compound when replacing { lubricant plug, t' l' 13, D'ff T ' eren"a. S:an~mlsslon.' eerIng gear. { Inspect oil level every 1,000 miles and keep oil up to filler plug, using same make and grade oil as in unit; if same grade oil is not available, drain, flush and use new oil. (Drain and flush twice yearly or every 10,000 miles, prefer ably in the spring and falL) SAE-90 cold climate. SAE-140 warm climate, For differential (4 pints), use SCL, EP gear oil or multi~purpose gear lubricant suitable for hypoid axles as supplied by a reputable refinery. Keep breather fittings clean. For transmission (3 pints) and steering gear (1 pint), use SCL, EP gear oil or multi-purpose gear oil, supplied by a reputable refinery,
14. C b t l ' k ' Parking brake linkage: . . pIns, plVO tpIns, an d ' u b rlcate lIn k age, cleVIS " ' ar ure or 1n age. do 1 t he
Door hinges t door latches: or a c s.
3,000 TO 5,000 MILES 15. Propeller shaft slip joint!
}L
S I'd' 1 Ing
' ' sur f aCES WIt h englne
'I 01,
P ut
't SUl a bl e
1U b' Ticant on
Remove plug and install a pressure"'gun fitting. Use a viscous chassis lubricant. Force a small amount into joint. Note: Too much pressure will damage oil seal and retainer. Remove fitting and replace plug . .!2,OOO MILES
16.
1b
ron w ee
' {Remove wheels~ clean and inspect bearings, races and wheel hubs. Repack bearings, using a short fiber wheel e a rings: bearing grease. Replace wheels and adjust bearings~
, {Remove grease plug and install a pressure-gun fitting. Use a viscous chassis lubricant. Force about one oz. 17. Rear wheel bearmgs: into bearing cavity. Note: Too much lubricant will damage brake lining. Remove fitting and replace plug, 15,000 TO 20,000 MILES 18. Propeller h f t 1 ' ' t {Remove plug, install a pressure-gun fitting and fill (under low pressure). Use SAE-140 gear oil. s a unlversa Jom s: Remove fitting and replace plug, Use a viscous chassis lubricant.
19. Window regulator: Remove door panel and lubricate regulator slide.
LUBRICATION CHART
l-120 SERIES TRUCKS
Front spring front and rear pins Engine oil filler (3~ (No lub. req'd) (9) \ ", Steering gear (13)\ \ Drag link (lO).....
/Generator Water pump ~y (No lub. req'd) (7)/1

I 1
(11
) Air cleaner
""' . . . -. . .......... "" '----
'<
'\ \
,Battery
(4)
I' I'
I'
Engine oil filter (2) Drag link (10)--
-~~:::-(:l -:-- J(8) - - - -.//
""' .......... ' - - - -
'-----:.-=----./
./
'\'\ '1 "
Front wheel bearings (Both sides) Steering knuckles (Both sides) Tie rod ends (Both sides) Distributor
(16)--'J l /J
U
/
// /
-E]
"
\'T::;~~i( r----;
(6)
""
,Carburetor (14) linkage
"
__ ___,/,,11
//~~/Jl1
"
/
I
/ /,
iJ
-\-
--------Starting motor
(11) (13)
(lO)- - --"
"" / /
/ / /" 1/ /
II
iflJtc:af-.:!::,,"",,,
(12)-
/
/
I
/1 Y /
It)
II / / I
Shifting bracket
(10)--------1
__ J
II I I
/
II
/1/ t:'b/ ::~~

/0
tI
/ I
I /
fD . ....-1"J /'
l!;=:;;;
II.
...-"'--/F'
Transmission
_",..Parking brake linkage (14)

,
..... \ - :;::::::- . . . _--].J..-
Master cylinder (5)-Shifting bellcrank
1/ / / "
(10)-----'"
1/
II
1/ ///
/ I
1/1
/
1/11 I I I I I II /
I
/~r".C ~l8--l-".----
7F- ___ _________

1 [Y
//
/ ././
_------Universal joint Slip joint
(IS)
(15)
,//
~--Universal joint
./
(IS) (13)
(10)/ / / /
p
/r- -- - -- Differential
I
Clutch release fork shaft (S)J Center bearing (7)-------/1/ (No lub. req'd) I / Parking brake linkage (14)-----1
I
vvv/
"
Rear wheel bearings (Both sides) Door hinge
(17Y
(14)----------...-:..:::-.:::-
Rear spring front and rear pins (9)-- (No tub. req'd)
-- ----
Door panel 0 ,--lJl----------Door latch c:;::} ____ ~ -----Window regulator
(14)
(19)
A-23655
Lubrication periods provide an excellent opportunity to inspect and check for maintenance service that may be needed. Early attention to minor service needs at this inspection will usually prevent serious breakdown later.
PRINTED IN UNITED S1',I.r5 0"
"ME~IC'"

L-120 SERIES TRUCKS
L Engine: Keep crankcase filled to correct level with high-grade engine oil. Changing oil regularly will remove accumulated dirt. Cold weather requires frequent oil change because of increased use of choke, also condensation of moisture. Refill capacity, 7 quarts; add I quart for oil flIter. For trucks in mUlti-stop, or other services where sustained high engine speeds are not encountered, select oil grade a5 follows: TEMPERATURES OIL GRADE .. 90~ (F.) and ug . . . . . . . . . . . . SAE-40 32 (F.) to 90 (F.) . . . . . . . . .. SAE-40 (* See Hot Climate - High Speed instruction following) TEMPERA TURES 10 0 (F.) to 32 0 (F.) (above zero) 0 (F.) to Minus 10 10 0 (F.) above zero . . . . . . . OIL GRADE SAE-20W SAE-IOW
Tern eratures lower than minus 10 0 F. below zero use SAE-IOW plus kerosene. SAE-IOW may be safely diluted with colorless kerosene up to 0 percent: mix t oroughly before adding to engine, and check oil level OFTEN - because kerosene evaporates rapidly at crankcase temperature. Hot Climate - High Speed: For trucks operating on highway, or other service demanding sustained high engine speeds, use engine. oil having a viscosity as near SAE-40 as possible and as starting ability will permit. Note: High viscosity oils are available which also have very good cold-pour characteristics. PERIODlCALLY 2. E' ngme '1 filt
01
{Change cartridge when oil has darkened. Remove filter cover and cartridge, clean inside of filter - install new er. cartridge. Run engine for a few minutes and check filter for leaks.
3. Engine oil filler: Remove filler cap, clean element, and dip in engine oil - then drain and replace. 4. Battery: Check water level. If necessary, add pure distilled water to 3/8 inch above plates. Do not overfill. S. 6
.
B k t I' d {CheCk fluid level. Do not a!low dirt to enter. If necessary, fill to 3/4 inch frOIll top with a high grade autora e mas er cy mer: motive type brake fluid. Do not overfill. A'
IT C eaneT: grade used in crankcase.
{Remove filter element and wash in kerosene. Clean oil sump and refill to indicated level with clean engine oil, same . Further lubrication not required. 500 TO 1,000 MILES
7. Wp ater P umP : {t t b . }Lubricated at factory. rope lI er s h a cen er earing:
8. Steering knuckles: }use a viscous chassis lubricant or SAE-140 gear oiL Do not oyer-lubricate - too much oil will cause fail. Clutch release fork shaft: ure of brake and c1ufch lining. 9. Spring pins: Pins are rubber mounted; lubrication not require? 10. Drag link; rod ends: ) Shifting bracket: Force a viscous chassis lubricant or SAE-140 gear oil into fittings until old lubricant, dirt, and water are Shifting bellcrank: expelled.
11. GStenet:ator: t }Put 10 to 20 drops light engine oil in each cup. Do not over-lubricate. ar lng rno or:
12. Distributor' on felt wick. Apply a light coat of vaseline to distributor cam and contact arTn fiber rubbing block. Note:' Lubricate
. distributor shaft at overhaul or at 2S,OOO-mile intervals. Use SAE-20 engine oil. Use sealing compound when replacing lubricant plug.
Inspect oil level every 1.000 miles and keep oil up to filler plug. using same make and grade oil as in unit; if same 13. Differential: grade oil is not available, drain, flush and use new oil. (Drain and flush twice yearly or every 10,000 miles, preferTransmission: ably in the spring and faiL) SAE-90 cold climate. SAE-140 warITl climate. For differential (4 pints), use SCL, EP Steering gear: gear oil or multipurpose gear lubricant suitable for hypoid ades as supplied by a reputable refinery. Keep breather fittings clean. For transTnission (3 pints) and steering gear (1 pint), use SCL, EP gear oil or Inulti-purpose gear oil, supplied by a reputable refinery. 14.
Put one drop of light oil on movable contact arm pivot pin. Remove rotor and put two or three drops of light engine oil
Door hinges, door latches:
~ar~ing ~ra~~ ~inkage: ar ure or mage:
}Lubricate linkage. clevis pins, pivot pins. and sliding surfaces with engine oil. d lat h oor c es.
~OOO
Put suitable lubricant on
TO 5.000 MILES
15
11 h ft I' . . t.{Remove plug and install a pressure-gun fitting. Use a viscous chassis lubricant. Force a small amount rope er s a s.p JOIn. into joint. Note: Too much pressure will damage oil seal and retainer. Remove fitting and replace plug. 10,000 MILES
16. Front wheel b"arings:} Remove wheels, clean and inspect bearings, races and wheel hubs. Repack bearings. using a short fiber wheel 11. Rear wheel bearings: bearing grease. Replace wheels and adjust bearings. 15,000 TO 20,000 MILES 18 P 11 h ft' l ' I t {Remove plug, Install a pressure-gun fitting and fill (under low pressure). Use SAE-140 gear oiL . rope er s a Ull1versa JO n s: Remove fitting and replace plug. 19. Window regulator: Remove door panel and lubricate regulator slide. Use a viscous chassis lubricant,
L UBRICA TION Section B Page 5
LUBRICATION CHART
l-130 SERIES TRUCKS
Front spring front pins (9~ (No lub. req'd) "
enerator (11) Water pump 17 I Battery (4) "Steering gear (13).... \ (No lub. req'd)(7)/1 / Drag link (10}.-.. ", \, I /! I ',' , K / '--'--. \ '\ / Engine oil(2)___ ,,'--------, / -----_'----------~~"'~=~~ filter -. \
Drag link (10}--------_::--_
/ \
" Engme 011 filler (3),
"
(6)
(14 )
Front wheel bearings (16)-

(Both sides)
(10)
Steering knuckles
(Both sides)
I I I
",'" I I
Tie rod ends (Both sides)
(10}- _____ .../1

'"
II
'"
I
(11)
I
/ /
",/
/
I
/
/
D'Istn u tor (12) ----- - -'" 'b

I
I I 1 1 . /I / 1 // 1/1//
/
Shifting bracket
(lO)------/' / /
I
/
"I / I / I /1r~ I
I /
I I /
/
I
Master cylinder (5)------J 1 //// / 1 / /

I
if--11J1
/ .... /
----
___ -
--
,..,,/
///
Transmission
(13)
(14)
__ -
Par k' lng b rak e I' k age In
_-----Universal joint
_-
(18)
Shifting bellcrank
(10)--
-'
,v
ij
1/ / /
//
/
1;1 /
"/
(10)/
/)1
1/ VI
------------Slip J'oint (15) Rear spring front pins (10) (Both sides)
_--
Clutch release fork (8)---.-1' ( / ] shaft VV '" Center bearing (7)-------'" (No lub. req'd)
I
'
---mr:D--~~::~:'::
l----~~~-7
/'
(18) (13)
Rear wheel bearings (17Y (Both sides) Door hinge Rear spring rear pins (10-- (Both sides)
----------Door latch
----~Window
(14) (19)
regulator
A-22865
PRINTED IN UNIYE:D STATES OF AM!:RICA
LUBRICATION CHART INSTRUCTIONS L-130 SERIES TRUCKS

DAILY
1. Engine: Keep crankcase filled to correct level with high-grade engine oil. Changing oil regularly will remove accumulated dirt. Cold
weather requires frequent oil change because of increased use of choke, also condensation of moisture. Refill capacity, 7 quarts; add I quart for oil filter. For trucks in mUlti-stop, Or qther services where sustained high engine speeds are not encountered, select oil grade as follows:
.. 90 0 (F.) and up . . . . . . .
TEMPERA TU RES OIL GRADE SAE-40 o (F.) to 90 0 (F.). . . . . . . . . . 3Z SAE-40 (* See Hot Climate - High Speed instruction following)
TEMPERATURES 100 (F.J to 320 (F.J (above zero) Minus 100 (F.) to 100 (F.) above zero . . . .
OIL GRADE SAE-2.0W SAE-IOW
eratures lower than minus 100 F. below zero, use SAE-IOW plus kerosene. SAE-IOW may be safely diluted with co or ess erosene up to 0 percent; mix thoroughly before adding to engine, and check oil level OFTEN - because kerosene evaporates rapidly at crankcase temperature. Hot Climate - High Speed: For trucks operating on highway, or other service demanding sustained high engine speeds, use engine oil having a viscos,ity as near SAE-40 as possible and as starting ability will permit. Note: High viscosity oils are available which also have very good cold-pour characteristics. PERIODICALL Y 2.. E' 'I f'U {Change cartridge when oil has darkened. Remove filter cover and cartridge, clean inside of filter - install new ngme o l l e r : cartridge. Run engine for a few minutes and check filter for leaks. Remove filler cap, clean element, and dip in engine oil - then drain and replace. If necessary, add pure distilled water to 3/8 inch above plates. Do not overfill. If necessary, fill to 3/4 inch from top with a high grade auto-
3. Engine oil filler:
4. Battery: Check water level. S.
B k t I' d {CheCk fluid level. Do not allow dirt to enter. ra e mas er cy 1n er, motive type brake fluid. Do not overfill.
6 A' 1 {Remove filter element and wash in kerosene. Clean oil sump and refill to indicated level with clean engine oil, same lr c eaner: grade used in cra.nkcase.
7. WPraterlPlumPh:a ft cent er b earlng: }Lubricated at factory. ' ope er s
Further lubrication not required.
500 TO 1,000 MILES
8. Steering knuckles: }use a viscous chassis lubricant or SAE140 gear oil. Clutch release fork shaft: failure of brake and clutch lining.
9. Front spring front pins: Are rubber mounted: lubrication not required.
Do not over .. lubricate - too much oil will cause
10. Front spring rear pins: ) Rear spring all pins: Drag link; tie rod ends: Force a viscous chassis lubricant or SAE-140 gear oil into fittings until old lubricant, dirt, and water are Shifting bracket: expelled. Shifting bellcrank:
11. G ene ator: t }Put 10 to 2.0 drops light engine oil in each cup. lng rno Or: Star t7 Do not over-lubricate.
12..
Put one drop of light oil on movable contact arm pivot pin. Remove rotor and put two or three drops of light engine oil D' t 'b t ,on felt wick. Apply a light coat of vaseline to distributor cam and contact arm fiber rubbing block. Note: Lubricate 1S r l U or.{ distributor shaft at overhaul or at Z5 ,OOO-mile intervals. Use SAE-2.0 engine oil. Use sealing compound when replacing lubricant plug. Inspect oil level every 1,000 miles and keep oil up to filler plug, using same make and grade oil as in unit; if same t' I' grade oil is not available, drain, flush and use new oil. (Drain and, flush twice yearly or every 10,000 miles, prefer T' eren"a,' ably in the spring and fall.) SAE-90 cold climate. SAE-140 warm climate. For differential (4 pints), use SCL, EP stan~mlsslOn.: gear oil or multi-purpose gear lubricant suitable for hypoid axles as supplied by a reputable refinery. Keep breather eermg gear. { fittings clean. For 3-speed transmission (6 pints). for 4-speed transmission (5 pints), and steering gear (1 pint), use SCL, EP gear oil or multi-purpose gear oil, supplied by a reputable refinery. D'ff }L u b rlcate I' k age, c I " ' ln eV1S door latches.
plns~
13.
14. C b Parking tbrake linkage: l'nk
D:~r u:i~;:S, 1 do~;el~tches:
pivot pins, and sliding surfaces with engine oil.
Put suitable lubricant On
3,000 TO 5,000 MILES 15. P rope

11
h ft I' "t.{Remove plug and install a pressure-gun fitting. Use a viscous chassis lubricant, Force a small amount er s a s lp Jam. into joint. Note: Too much pressure will damage oil seal and retainer. Remo.;e fitting and replace plug. 10,000 MILES
16. Front wheel bearings: lRemove wheels, clean and inspect bearings, races and wheel hubs. 17. Rear wheel bearings: [bearing grease. Replace wheels and adjust bearings. 15,000 TO 20,000 MILES
Repack bearings, using a short fiber wheel
18 P 11 hit I ' ' t {Remove plug, install a pressure-gun fitting and fill (under low pressure). Use SAE-140 gear oil. . rope er s a unlversa Jom s: Remove fitting and replace plug. 19. Window regulator: Remove door panel and lubricate regulator slide. Use a viscous chassis lubricant.
LUBRICATION
L~LINE
Section B Page 7
LUBRICATION CHART
L-150 SERIES TRUCKS
Steering gear Spring pim (Both sides) Drag link Engine oil filter Drag link Front wheel bearing (Both sides) Steering knuckles (Both sides) Tie rod ends (Both sides) Distributor Shifting bracket Master cylinder Clutch and brake pedals Clutch release fork shaft Parking brake linkage Universal joint Spring pim (Both sides) Center bearing (No lub. req'd) Rear wheel bearings (Both sides) Door hinge Spring pins (Both sides)
-\Vindow regulator
(It)
A.22864
/,
(9)____
, ......
,,
r Water pump (7}
(No lub. req'd)

(I J)
'
..... ......
.......
-----
(7/./
--Y
.---- Universal joint ....-Differential

(13)
(18)
..;-
_---i.~~~'----" -<Y
P1iINTD IN UNITED STATES OF AMRICA
lUBRICATION CHART INSTRUCTIONS l-150 SERIES TRUCKS

1. Engine: Keep crankcase filled to correct level with high-grade engine oil. Changing oil regularly will remove accuInulated dirt. Cold weather requires frequent oil change because of increased use of choke, also condensation of moisture. Refill capacity, 7 quarts; add 1 quart for oil filter. For trucks in Inulti-stop, or other services where sustained high engine speeds are not encountered, seled oil grade as follows:
* 90 0 no
TEMPERATURES OIL GRADE (F.) and up . . . . . . . . . . .. SAE-40 (F.) to 90 0 (F.). . . . . . . . . . . SAE-40 (* See Hot Climate - High Speed instruction fOllowing)
TEMPERA TU RES 10 0 (F.) to 32 0 (F.) (above zero) Minus 10 0 (F.) to 10 0 (F.) above "ero . . . .
OIL GRADE SAE-ZOW SAE-IOW
Temperatures lower than minus 10 0 (F.) below "ero, use SAE-IOW plus kerosene. SAE-IOW Inay be safely diluted with colodess kerosene up to 30 percent; mix thoroughly before adding to engine, and check oil level OFTEN - because kerosene evaporates rapidly at crankcase temperature. Hot Climate - High Speed: For trucks operating On highway, Or other service deInanding sustained high engine speeds, use engine oil having a viscosity as near SAE-40 as possible and as starting ability will permit. Note: High viscosity oils are available which also have very good cold-pour characteristics. PERIODICALL Y
Z.
E' '1 f'lt {Change cartridge when oil has darkened. ReInove filter COver and cartridge, clean inside of filter ngme 01 I er: cartridge. Run engine for a few Ininutes and check filter for leaks.
install new
3. Engine oil filler: ReInove filler cap, clean element, and dip in engine oil - then drain and replace. 4. Battery: Check water level. If necessary, add pure distilled water to 3/8 inch above plates. Do not overfill,
S.
k t I' d {CheCk fluid level. Do not allow dirt to enter. If necessary, fill to 3/4 inch from top with a high grade autora e mas er cy mer: motive type brake fluid. Do not overfill.
For engine air cleaner - remove filter element and wash in kerosene: clean the oil sump and refill to indicated 6. Engine air cleaner: level with clean engine oil, same grade used in crankcase. For hydrovac air cleaner - remove cleaner. disHydrovac ir cleaner: mantle and clean parts in a cleaning solvent and allow to dry; saturate element with a light oil and replace a parts.
7. pWaterllPumPh:aft t b ' } Lubricated at factory. rope er S cen er earIng:
Further lubrication not required.
500 TO 1,000 MILES

8. Steering knuckles: }use a viscous chassis lubricant or SAE-140 gear oil. Do not over-lubricate - too much oil will cause failClutch release fork shaft: ure of brake and clutch lining,
9. Spring pins: ) 10. D{,~f. lin~: ti~ rt~d ends: Force a viscous chassis lubricant or SAE-140 gear oil into fittings until old lubricant, dirt, and water are I lng rac e , 11 d
Shifting bellcrank: expe e .
11. GStenet:ator: t }Put.10 to ZO drops light engine oil in each cup. Do not over-lubricate. ar 109 mo or: Put one drop of light oil on movable contact arm pivot pin, ReInove rotor and put two or three drops of light engine oil on felt wick. Apply a light of vaseline to distributor cam and contact rubbing block. Note: lZ. D'1St r l'b U t or.. distributor shaft at overhaul coatat Z5,OOO-1l1ile intervals. Use SAE-ZO enginearm fiber sealing COITlpound when Lubricate or oil. Use replacing { lubricant plug. Inspect oil level every 1,000 !niles and keep oil up to filler plug, using Same make and grade oil as in unit: if same Diff t' I' grade oil is not available, drain, flush and use new oil. (Drain and flush twice yearly or every 10,000 m.iles, prefer . T eren, la,' ably in the spring and fall.) SAE-90 cold climate. SAE-140 warm. climate. For differential (3 pints)' use SCL, EP Sran~!nlsslon: gear oil or multi-purpose gear lubricant suitable for hypoid axles as supplied by a reputable refinery. Keep breather eermg gear. fittings clean. For 4-speed heavy-duty transITlission (5 pints), 4-speed syncro-mesh transmission (8 pints) and steer ing gear (1 pint), use SCL, EP gear oil or multi-purpose gear oil. supplied by a reputable refinery.
13
14. Parking brak; linkage: }LUbricate linkage, clevis pins. pivot pins, and sliding surfaces with engine oil. Put suitable lubricant on Carburetor hnkage: door latches Door hinges, door latches: . 3,000 TO 5,000 MILES 15 . P 11 haft I' "t.{Remove plug and install a pressure-gun fitting. Use a viscous chassis lubricant. Force a SInall amount rope er s s lp Jom. into joint. Note: Too much pressure will damage oil seal and retainer. Remove fitting and replace plug. 10,000 MILES 16. Front wheel bearingS:}Remove wheels, clean and inspect bearings, races and wheel hubs. Repack bearings, using a short fiber wheel Rear wheel bearings: bearing grease. Replace wheels and adjust bearings, 15,000 TO ZO,OOO MILES 17. H d {Must be lubricated every 20,000 mile. or once a year, before cold weather sets in. Remove pipe plug (located in air inlet y rovac: end of cylinder). Use vacuum cylinder oil and add to top level of plug hole. Replace plug.
. . plug, 11. Pr a P e 11 er s haft unlvers al j amt s: {Remove fitting install a pressure-gun fitting and fill (under low pressure). Use SAE-l40 gear oil. Remove and replace plug. 19. Window regulator: Remove door panel and lubricate regulator slide. Use a viscous chassis lubricant.
LUBRICATION CHART
L-160 SERIES TRUCKS
Engine oil filler (3)
Spring pins (Both sides) Steering gear Drag link Front wheel bearing (Both sides) Steering knuckles (Both sides) Tie rod ends (Both- sides) Distributor Spring pins (Both sides) Clutch and brake pedals Master cylinder Universal joint Center bearing Slip joint Universal joint Spring pim (Both sides) Universal joint Rear wheel bearings (Both sides) Door hinge
(to) (to)
" --~
(1-3)
(II)
(13) - __
(6)
(I ..
n
(11)
(H)
..
(18) (8)
~~--IIS ----------~I --- ~ ..---""--
fork
(l 3)
\
\
\
\
",,-- (Bus) H\'drovac on kft side

"- H vdn)\'(\c
(17)
(15)
---~~~~~~rr-~
- --
(18) - - - (10)
--[J~-::'-~
U '-
:=n \\'-
H,d",'ac a;, clean" (6)

P"klng b"k< linkage (9)
(18) (16)
-- - - - m a l
(13)
Spring pins (Both sides)
(nh~~;oro
~--~----- Window
A-23657
- IP lJl_-
000, latch
(14)
regulator (19)
PR1NTIO IN UNITD SfAf.tS OF ..... ERICA
lUBRICATION CHART INSTRUCTIONS l-160 SERIES TRUCKS

1,
Engine: Keep crankcase filled to correct level with high-grade engine oil. Changing oil regularly will remove accumulated dirt. Cold weather requires frequent oil change because of increased use of choke, also condensation of moisture. Refill capacity, 7 quarts: add 1 'quart for oil filter. For trucks in multi-stop, or other services where sustained high engine speeds are not encountered, select oil grade as follows: TEMPERA TURES OIL GRADE .. 90 0 ( F.) and up . " " ... SAE-40 0 0 32 (F.) to 90 (F.). . . . . . .. . . . . SAE-40 ( .. See Hot Climate - High'Speed instruction following) TEMPERATURES 10 0 (F.) to 32 0 (F.) (above zero) 0 Minu'l, 10 (F.. l to 10 (F.) above zero.. OIL GRADE SAE-20W SAE-IOW
Temperatures lower than minus 10 0 F. below zero, use SAE-10W plus kerosene. SAE-IOW may be safely diluted with co or eBS erOBene up to 30 percent; mix thorouthly before adding to engine, and check oil level OFTEN - because kerosene evaporates rapidly at crankcase temperature. Hot Climate - High Speed: For trucks operating on highway, or other service demanding sustained high engine- speeds, use engme oil having a viscosity as neal' SAE-40 as possible and as starting ability will permit. Note: High viscosity oils are available which also have very good cold-pour characteristics. EERIODICALL Y E' '1 f'lt {Change cartridge when oil has darkened. Remove filter cover and cartridge, clean inside of filter - install new 2. ngme o. 1 er: cartridge. Run engine for a few minutes and check filter for leaks.
3. Engine oil filler: Remove filler cap, clean element, and dip in engine oil - then drain and replace.
4. Battery: Check water level. If necessary, add pure distilled water to 3/S inch above plates. 5 . B k t I' d {Cheek fluid level. Do not allow dirt to enter. ra e mas er cy in er: motive type brake fluid. Do not overfill. Do not overfill.
If necessary, fill to 3/4 inch from top with a high grade auto
For engine air cleaner - remove filter element 'and wash in kerosene; clean oil sump and refill to indicated 6. Hydrovac air cleaner: level with clean engine oil? same grade used in crankcase, For hydrovac air cleaner - remove cleaner, disEngine air cleaner: mantle and clean parts in a cleaning solvent and allow to dry; saturate element with a light oil and replace parts.
7. Water pump: Lubricated at factory
Further lubrication not required. 500 TO 1,000 MILES
8.
~~e~r:;-g ~nuckl:s:k
Pr~;el1:: :~~~t ~:nt:r \e'aring:j knuckles, and on clutch shaft cause failure
h ft
Use a viscous chassis lubricant or SAE-140 gear oil. Do not over-lubricate. of brake and clutch lining.
Too much oil on
9. Parking brake linkage: Lubricate linkage, clevis pins, pivot pins, and sliding surfaces with engine oil. 10.
i?,.:,n~.p~~st:le ro den . ds' g 1n

1
}Force a viscous chassis lubricant or SAE-140 gear oil into fittings until old lubricant, dirt and water are p l! d
Clutch and brake pedals: ex e e .
10 to 20 drops light engine oil in each cup. Do not over-lubricate.
11.
~t:~~~::o~:otor:}put
12.
Put one drop of light oil on movable contact arm pivot pin. Remove rotor and put two or three drops of light engine oil D' t 'b t ,on felt wick. Apply a light coat of vaseline to distributor cam and contact arm fiber rubbing block. Note: Lubricate 15 ,., u or. distributor shaft at overhaul or at 25,OOO-tnile intervals. Use SAE-20 engine oil. Use sealing cotnpound when replacing lubricant plug.
Inspect oil level every 1,000 miles and keep oil up to filler plug, using same make and grade oil as in unit; if same grade oil is not available, drain, flush and use new oil. (Drain and flush twice yearly or every 10,000 miles, prefer ably in the spring and fall.) SAE-90 cold climate. SAE-140 warm climate. For single reduction axle (8 pints). and 13. Differential: for two-speed axle (13 pints). Use SCL, EP gear oil or multi-purpose gear lubricant suitable for hypoid axles as sup Transmission! plied by a reputable refinery (not Eaton Axles). For Eaton Axles, use hypoid gear lubricant available as Elco Gear Steering gear, Safety "28 11 or its equivalent (see instructions. section HAil). Keep breather fittings clean. For 4-speed syncro-mesh Electric shift, transmission (S pints) and steering gear (1 pint). use SCL, EP gear oil or multi-purpose gear oil, supplied by a reputable refinery. For electric shift, inspect oil level every 10,QOO miles and keep filled to plug level with SAE-IO oil. 14. Carburetor linkage: }Lubricate linkage, clevis pins, pivot pins, and sliding surfaces with engine oil. Door hinges, door latches: door latches. 3,000 TO 5,000 MILES 15 . P 11 h ft rope er s a
S
Put suitable lubricant on
I' . . t,{Remove plug and install a pressure-gun fitting. Use a viscous chassis lubricant. Force a small amount 1p J01n. into joint. Note: Too much pressure will damage oil seal .and retainer Remove fitting and repla.ce plug. 10,000 MILES
16. Front wheel bearings: LRernove wheels, clean and inspect bearings, races and wheel hubs. Repack bearings, using a short fiber wheel
Rear wheel bearings:
J bearing grease.
Replace wheeis and adjust bearings. 15,000 TO 20,000 MILES
17. 18,
H d {Must be lubricated every 20,000 tniles or once a year, before cold weather sets in. Retnove pipe plug (located in air inlet y rovac: end of cylinder). Use vacuum cylinder oil and add to top level of plug hole. Replace plug. P II rope er
5
hit l ' . t {RetnOve plug, install a pressure-gun fitting and fill (under low pressure). Use SAE-140 gear oil. a umversa Jom s: Remove fitting and replace plug. Use .. viscous chassis lubricant.
19. Window regulator: Remove door panel and lubricate regulator slide.
LUBRICATION
Section B Page 11
LUBRICATION CHART
L-170 SERIES TRUCKS
Spring pills (Both sides) Steering gear Drag link Front wheel hearing (Both sides) Steering knuckles (Both sides) Tie rod ends (Both sides) Air cleaner Distri bu tor Oil filter Spring pins (Both sides) Clutch and brake pedals Master cylinder Universal joint
(26) (4)
(12) (14)
(IS)
(10)
"""
----------1-1---
"~
------(BlIs) Hvdrovac on left sid.,..

"!---I"'"1"'C-'
""'" ,'- Hvdl'ovac (3.25) """'-- Parking brake Linkage

(26)
(13)
Center bearing (19) Slip joint Spring pins ,(BothI S,id.eS) U nlversa Jomt
_~--...:r----~--[J
_------ Universal joint
(22) - - - -
(6)--- -.-
(26) _ -
OOr-r.__
f:;Jl
Auxiliary spring ends (Both sides)
(9)
-----=-..;
Rea. wheel beadn", (23) (Both sides)

Differential Door hinge Spring pins (Both sides)
(21)
l
r-IF1---Dl~or latch
A-22835
--1-0--- TTr- 0
(15) (27)
Door panel (15)--------~S~E (notfor8Us )[
. .-""..;:::-~ .
(6)------
~--t:JI.-.L
WIndow regulator
PRINTEQ IN UNITED STATES OF AMERICA
LUBRICATION
Section B
Page 12

L-170 SERIES TRUCKS
1. Engine: Keep crankcase filled to correct level with high-grade engine oil. Changing oil regularly will remove accumulated dirt. Col< weather required frequent oil change because of increased use of choke, also condensation of moisture. Refill capacity quarts; add I quart for oil filter. For trucks in multi-stop, or other services where sustained high engine speeds are no encountered, select oil grade as follows:
I
TEMPERATURES 90 0 {F.} and up . . . . . 0 (F.) to 90 0 (F.) . . . . . . . 32
OIL GRADE SAE-40 SAE-40
TEMPERATURES 10 0 (F.) to 32 0 (F.) (above zero) 0 (F.) to Minus 10 10 0 (F.) above zero . . .
OIL GRADE SAE-20W SAE-IOW
Temperatures lower than minus 10 0 (F.) below zero, use SAE-IOW plus kerosene. SAE-IOW may be safely diluted wit} colorless kerosene up to 30 percent; mix thoroughly before adding to engine, and check oil level OFTEN - because kerosen< evaporates rapidly at crankcase temperature.
Hot Climate - High Speed: For trucks operating on or other service demanding sustained high engine speeds, us, engine oil having a viscosity as near SAE- 50 as and as starting ability will permit. Note: High viscosity oils an available which also have very good cold-pour characteristics.
500 TO 1,000 MILES
2
Oil filter.{Change cartridge when oil has darkened. Remove filter cover and cartridge, clean inside of filter - install new cartridge. . . Run engine for a few minutes and check filter for leaks.
For engine air cleaner remove reservoir and djspose dirty oil; clean filter and reservoir and refill to oil level mark 3. Air cleaners: ,with clean engine oil, same grade used in crankcase~ For hydrovac air cleaner - remove cleaner, dismantle and clean lparts in a cleaning solvent and allow to dry; saturate element with a light engine oil and replace parts.
,. J
4. Battery: Check water level. If necessary, add pure distilled water to 3/8 inch above plates. Do not overfill.
S.
k t I' d . {CheCk fluid level. Do not allow dirt to enter. If necessary. fill to 3/4 inch from top with a high grade autora e mas er cy In er. motive type brake fluid. Do not overfill.
6. } Force a viscous chassis lubricant or SAE-140 gear oil into fittings until old lubricant, dirt, and water are 7. 8. Tie. rods: expelled, 9. Auxiliary spring ends:
10. Clutch release fork Shaft'} , ' . Use a V1SCOUS chassls lubrlcant or SAE-140 II. Cl u t c.h andb ra k e pe d a 1: and on clutch shaft will cause failure of brake
oil. Do not over-lubricate. Too much oil on knuckles) clutch lining.
12. St eering k nuc kl es:
13, Parking brake linkage: }L u b ' t e I' k age, c I " pIns, plVO pins, and sliding surfaces with engine oil. Put suitable lubricant on 't t l' k rIca In eVlS 14. C b IS. D~~r U:i~;:S, l~o~~el:atches: door latches. 16. SGtenetrator: t }put 10 to 20 drops light engine oil in each cup. 17. aringmoor! Do not over-lubricate.
Put one drop of light oil on movable contact arm Remove rotor and put two or thre'e drops of light engine oil on felt wick. Apply a coat of vaseline to the cam and contact arm fiber rubbing block. NOTE: Lubri 18. Distributor: cate distributor shaft overhaul or at 25,OOO-miIe intervals. Use SAE-20 engine oil. Use sealing compound when re placing lubricant plug. For distributor with grease cup: Fill cup with SAE-140 gear oil, as required, and turn one turn every 1,000 miles.
19. Propeller shaft. center bearing: Use a medium short-fiber wheel bearing grease (sodium-soap type). 20. Steering gear: Remove pipe plug and inspect oil level every 1,000 miles. USB SAE-140 gear oil. Keep housing full of oil. 21. Transmission Refill: Code No. 1304 - Capacity Code No. 1307 - Capacity Code No. 1308 - Capacity Differential Refill: Code No. 1405 - Capacity Code.No. 1406 - Capacity "'Code No. 1411 - Capacity *Code No. 1412 - Capacity 8 12 12 8 II 13 20 1,000 miles and keep oil level up to fiUer plug, using same make and same grade is not available, drain, flush and use new oil. (Drain and twice yearly or every 10,000 miles, preferably in the spring and fall.) SAE-90 cold SAE-140 warm climate. For transmission use SLC, EP gear oil or multi-purpose gear supplied by a reputable refinery. For rear axles (not Eaton) use SCL, EP gear oil or multigear lubricant suitable for hypoid axles supplied by a refinery. For Eaton use hypoid gear lubricant available as Elco Gear Safety or its equivalent (see in section "A"). "For Electric Shift, inspect oil level every 10,000 miles and keep to plug level with SAE-IO oil. 3,000 TO 5,000 MILES 22. Propeller shaft sl'p . int.{Remove plug and install a pressure-gun fitting. Use a viscous chassis lubricant, Force a small amount 1 JO into joint. Note: Too much pressure will damage oil seal and retainer. Remove fitting and replace plug.
23 Wh 1b
ee
. .{Remove wheels, clean and inspect bearings, races and wheel hubs. earmgs. ing grease. Replace wheels and adjust bearings.
Repack bearings) using a short fiber wheel bear
10,000 MILES 24 Water pump: {Remove plug and install a pressure gun fitting. . pressure). Use a short-fiber wheel bearing grease and fill housing (under low
25. Hydrovac: Inject two ounces vacuum cylinder oil twice yearly or every 10,000 miles, preferably in the spring and fall. 15,000 TO 20,000 MILES 26. Propeller shaft universal joints:
27. Window regulator;
plug, install a pressure-gun fitting and fill (under low pressure). fitting and replace plug.
Use SAE-140 gear oil.
Retnove door panel and lubricate regulator slide. Use a viscous chassis lubricant.
L-UNE MOTOR TRUCK SERViCE MANUAL
LUBRICATION CHART
l-lBO, l-lBl, l-lB2, l-lB3, l-lB4 TRUCKS
Spring pins (Both sides) Steering gear Drag link Front wheel bearing (Both sides) Steel'ing knuckles (Both sides) Tie rod ends (Both sides) Air cleaner Distributor Oil filter Spring pins (Both sides) Clutch and brake pedals Master cylinder Universal joint Starting motor
(16)
(20) -- __ _
(4)
(12) (14)
Ch)tch release fork shaft
(h.1)
Tr<ll1smission
(21)
_c_c-(GlIS)
(s)
(26)
j/
H vdr(lvac nn left side
""- Hvdrovac
(32<;)
Parking brake linkage
(13)
Center bearing (19) - - - - - Slip joint Spring pins (Both sides)

(22)-----~~
Universal joint
(26)
(6)-~------ --
.. U nlversa I Jomt
(26) - -
_1--------
no
Door panel
(notfor8US ) [
Auxiliarv spring ends (Both sides)
(9)
Rea. wheel beadngs (23)

(Both sides) Differential Door hinge Spring pins (Both sides)
(21)-~~~
(15) -------
r-r-=r1---
D(~or latch
(15)
(27)
___'~J
~--t::.-.L.--- Wmdow regulator A-228S5
PRINTED IN UNITED STA.TES OF AMERICA
LUBRICATION CHART INSTRUCTIONS L-180, L-181, L-182, L-183, L-184 TRUCKS

DAILY
1. Engine:
crankcase filled to correct level with high-grade engine oil. Changing oil regularly will remove accumulated dirt. Col frequent oil change because of increased use of choke, also condensation of moisture. Refill capacity J for oil filter. For trucks in multi-stop, or other services where sustained high engine speeds are nc oil grade as follows: TEMPERA TURES OIL GRADE * 90 0 (F.) and up . . . . . . . . . . . . SAE-40 0 (F.) to 90 0 (F.). . . . . . . . . . 32 . SAE-40 (" See Hot Climate - High Speed instruction following) 10 0 (F.) to 32 0 Minus 100 (F.) 10 0 (F.) above zero. OIL GRADE SAE-20W SAE-IOW
SAE-IOW plus kerosene. SAE-IOW may be safely diluted wit adding to engine, and check oilleve! OFTEN - because kerosen
crankcase temperatur e~
For trucks operating on highway~ or other service demanding sustained high engine speeds~ us as near SAE-40 as possible and as starting ability will permit. Note; High viscosity oils ar have very good cold-pour characteristics.
500 TO 1,000 MILES 2
0'1 n t
1 1
. {Change cartridge when oil has darkened. Remove filter cover and cartridge, clean inside of filter - install new cartridg< er. Run engine for a few minutes and check filter for leaks.
engine air cleaner remove reservoir and dispose dirty oil; clean filter and reservoir and refill to oil level mar clean engine oil, same grade used in crankcase. For hydrovac air cleaner remove cleaner, dismantle and clea in a cleaning solvent and allow to dry; saturate element with a light engine oil and replace parts.
3. Air cleaners:
4. 5.
Battery: Check water level.
If necessary, add pure distilled water to 3/8 inch above plates.
Do not overfill.
. d {Cheek fluid level. Do not allow dirt to enter. If necessary, fill to 3/4 inch from top with a high grade auto Brake master cy 1m er: motive type brake fluid. Do not overfill. ) Force a viscous chassis lubricant or SAE-140 gear oil into fittings until old lubricant, dirt, and water ar expelled.
6. Spring pins:
7. Drag links: 8. Tie rods: 9. Auxiliary spring ends: 10.
11.
U c. an rka e pc a. 12. St eerlng k nue l es:
giu~c~ re~e~se:ork rl~ft:}use
a viscous chassis lubricant or SAE-140 gear oil. Do not over-lubricate. and on clutch shaft will cause failure of brake and clutch lining.
Too much oil on knuckles
13. ~ar~ing ~ra~.e ~inkage: }LUbricate linkage, clevis pins, pivot pins, and sliding surfaces with engine oil. 14. ar ure or In age: door lat hes c. 15. Door hinges, door latches: 16. sGtenetrator: t }put 10 to 20 drops light engine oil in each cup. 17. armgmoor: Do not over-lubricate.
Put suitable lubricant o'
Put one drop of light oil On movable contact arm pivot pin. Remove rotor and put two or three drops of light engine oi on felt wick. Apply a light coat of vaseline to the distributor cam and contact arm fiber rubbing block. NOTE: Lubricat 18. Distributor: distributor shaft at overhaul or at 25,OOO-mile intervals. Use SAE20 engine oil. Use compound when replacin' and turn one tu::-n ever' { lubricant plug. For distributor with grease cup: fill cup. with SAE-140 gear oil, as 1,000 miles. 19. Propeller shaft center bearing: Use a medium short-fiber wheel bearing grease (sodium-soap type). 20. Steering gear: Remove pipe plug and inspect oil level every 1.000 miles. 21. Transmission Refill: Code No. 1307 Code No. 1308 Differential Refill: Code No. 1406 ".""'Cl:W *Code No. 1412 Code No. 1407 u8""'Cl.<V *Code No. 1413 Code No. 1415 L.a,UElCl<V
12 Pts. 12 Pts.
Use SAE-140 gear oil. Keep hOUSing full of oil.
11 20 20 22 19
Pts. Pts. Pts. Pts. Fts.
Inspect oil level every 1,009 miles and keep oil level up to filler plug I using same make an' grade oil as in unit; if same grade is not drain, flush and ust? new oil. (Drain an, flush twice yearly or every 10,000 miles, in the spring and falL) SAE-90 col, climate. SAE-140 warm climate. For transmission use SLC, EP ~ear oil or multi-purpos, gear oil supplied by a reputable refinery. For rear axles (not Eaton) use SCL, EP gear oil o. multi-purpose gear lubricant suitable for axles supplied by a reputable refinery. Fo Eaton axles, use hypoid gear lubricant as Elco Gear Safety "28" or its equivalent (se, instructions, section "A"). "For Electric Shift, inspect oil level every 10,000 miles and keel filled to plug level with SAE-lO oil.
3,000 TO 5,000 MILES 22. 23. Propeller shaft Wheel l' , . . Remove plug and install a pressure-gun fitting~ Use a viscous chassis lubricant. Force a srnall amoun t S Ip JOln :into joint. Note: Too much pressure will damage oil seal and retainer. Remove fitting and replace plug.
'1
wheels, clean and inspect bearings) race!? and wheel hubs. grease. Replace wheels and adjust bearings. 10,000 MILES
Repack bearings. using a short fiber whee
24.
Water
and install a pressure gun fitting.
Use a short-fiber wheel bearing grease and fill housing (under lo\'
25. Hydrovac: lnject two ounces vacuUm cylinder oil twice yearly or every 10,000 miles, preferably in the spring and fall. 15,000 TO 20,000 MILES 26. 27. h ft l ' . t {ReITIOVe plug, install a pressuregun fitting and fill (under low pressure). Use SAE-140 ;sear oil Propel er s a unlversa JOin S: ReITIove fitting and replace plug. 1 W'indow regulator: Remove
do~r
panel and lubricate regulator slide. Use a viscous chassie lubricant.
LUBRICATION CHART
L-190 SERIES TRUCKS
Spring pins (Both sides) Steering gear relay lever

Drag link
(6)--___
(8) -----___
-------
Oil filter
-- ----
Water pump (I) ,/
(25)
Steering gear Tie rod ends (Both sides) Air cleaner Starting motor
Clutch and brake pedals Battery Master cylinder Universal joint Center bearing Universal joint
Slip joint Spring pins (Both sides)
~-Spring pins (6) (Both sides)
(15)
(II)
-------- Transmission
(22)
(27)-----
-- ------
P--_-J - (Bus)
\
"
Hydrovac on left side
\ \
\. Hydrovac (3"26)
--0-
(6)----- ____ _
- - --- Parking brake linkage
(14)
I-Auxiliary spring ends (Both sides)
(10)
Univ"".1 joint Diffe"ntial
(27) -J~ (22)-____
--
-
--..
; ........ ,--....;...
Rear wheel bearings __. (Both sides) (24)

Door hinge Spring pins (Both sides) Spring pins (Both sides)
PRINTEO IN UNITED STATES 01'" Ar.tERtCA
--
- Door latch
'--.../
(16) (28)
--- Window regulator

A-23658
LUBRICATION CHART INSTRUCTIONS l-190 SERIES TRUCKS

1. Engine: Keep crankcase filled to correct level with high-grade engine oil. Changing oil regularly will remove accumulated dirt. Cold weather requires frequent oil change because of increased use of choke, also condensation of moisture~ Refill ca.pacity, 7 quarts; add 1 quart for oil filter. For trucks in multi-stop, or other services where sustained high engine speeds are not encountered, select oil grade 8:5 follows: TEMPERATURES OIL GRADE 90 (F.) and up . . . SAE-40 32 (F.) to 90 0 (F.). . . . . . . SAE-40 (* See Hot Climate - High Speed instruction following)
TEMPERATURES 100 (F.) to 32 0 (F.) (above zero) Minus lOa (F.) to 10 0 (F .)above Zero . . . . .
OIL GRADE SAE-20W SAE-IOW
Temperatures lower than minus lOa (F.) below zero, use SAE-IOW plus kerosene. SAE-IOW may be safely diluted with colorless kerosene up to 30 percent; nllX thoroughly before adding to engine, and check oil level OFTEN - because kerosene evaporates rapidly at crankcase temperature. Hot Climate - High Speed: For trucks operating on highway, or other service demanding sustained high engine speeds, use engine all havmg a viscosity as near SAE-40 as possible and as starting ability will permit. Note: High viscosity oils are available which also have very good cold-pour characteristics~
~TO
1,000 MILES
0'1 '1t 2.
1 1
.{Change cartridge when oil has darkened. Remove filter cover and cartridge, clean inside of filter - install new cartridge. er. Run engine'for a few minutes and check filter for leaks.
For engine air cleaner remove reservoir and dispose dirty oil; clean filter and reservoir and refill to oil level mark 3. Air cleaners: with clean engine oil, same grade used in crankcase. For hydrovac air cleaner - remove cleaner, dismantle and clean { parts iri a cleaning solvent and allow to dry; saturate element with a light engine oil and replace parts. 4. Battery: Check water level. If necessary, add pure distilled water to 3/8 inch above plates. Do not overfill. 5. B k t 1 d {Cheek fluid level. Do not allow dirt to enter. If necessary, fill to 3/4 inch from top with a high grade auto ra e mas er cy In er: motive type brake fluid. Do not overfill.
6. Ste~ring. gear relay arm:} 7. ;prm1p~n.s: Force a viscous chassis lubricant or SAE-140 gear oil into fittings until old lubricant, dirt and water are 8. expelled. 9. T~:~o~~: s: 10. Auxiliary spring ends: 11. Clutch release fork Shaft:}use a viscous chassis lubricant or SAE-140 gear oil, Do not over-lubricate. Too much oil on knuckles, and on clutch shaft will cause failure of brake and clutch lining. 13. Steering knuckles:
12. Clutch and brake pedal:
14. 15. 16. 17. 18.
Parking brake linkage: }Lubricate linkage, clevis pins, pivot pins, and sliding surfaces with engine oil. Put suitable lubricant on Carburetor Imkage: door latches Door hinges J door latches: . Generator: }put 10 to 20 drops light engine oil in each cup. Do not overlubricate, Startmg motor:
Put one drop of light oil on movable contact arm pivot pin, Remove rotor and put two or three drops of light engine oil on felt wick. Apply a light coat of vaseline to the distributor cam and contact arm fiber rubbing block. NOTE: Lubricate 19. Distributor: distributor shaft at overhaul or at 25,OOO-mile intervals. Use SAE-20 engine oil. Use sealing compound when replacing lubricant plug. For distributor with grease cup: fill cup with SAE-140 gear oil, as required, and tUrn one turn every 1,000 miles. Put one or two drops of engine oil on governQr rotor.
20. Propeller shaft center bearing: 21. Steering gear: 22. Transmission Refill: Code No. 1309 - Capacity Code No. 1310 Capacity Differential Refill: Code No. 1407 - Capacity Code No. 1408 - Capacity "Code No. 1413 - Capacity "Code No. 1414 Capacity Code No. 1415 - Capacity Code No. 1416 - Capacity
Use a medium short-fiber wheel bearing grease (sodium-soap type).
Remove pipe plug and inspect oil level every 1,000 miles. Use SAE-140 gear oil. Keep housing full of oil. 19 Pts. 19 Pts. 20 18 22 22 19 19 Pts. Pts. Pts. Pts. Pts. Pts. Inspect oil level every 1,000 miles and keep oil level up to filler plug, using same make and grade oil as in unit; if same grade is not available, drain, flush and use new oil~ (Drain and flush twice yearly Or every 10,000 miles. preferably in the spring and fall.) SAE-90 cold climate. SAE-140 warm climate. For transmission use SCL. EP gear oil or nlUlti-purpose gear oil supplied by a reputable refinery. For rear axles (not Eaton) use SCL. EP gear oil Or mUlti-purpose gear lubricant suitable for hypoid axles supplied by a reputable refinery. For Eaton axles, use hypoid gear lubricant available as Eko Gear Safety" 28" or its equivalent (see instructions. section "A"). *For Electric Shift, inspect oil level every lO~OOO IIliles and keep filled to plug level with SAE-IO oil. 3,000 TO 5,000 MILES
23 . 24.
II rope er
h ft a
S lp JOln.
. . t.{Remove plug and install a pressure-gun fitting. Use a viscous chassis lubricant. Force a small amount into joint. Note: Too much pressure will damage oil seal and retainer. Remove fitting and replace plug. Repack bearings. using a short fiber wheel
Wh
1b . {Remove '~heelsj clean and ~spect bearings, races and wheel hubs. ee eaTIngs: bearing grease. Replace wheels and adjust bearings. 10,000 MILES
25.
W t {Remove plug and install a pressure gun fitting. a er pump: pressure)
Use a short-fiber wheel bearing grease and fill housing (under low
26. Hydrovac: Inject two ounces vacuum cylinder oil twice yearly or every 10,000 miles, preferably in the spring and fall. 15,000 T020,000 MILES 2 1 h f 1 . t {Remove plug, install a pressure-gun fitting and fill (under low pressure). Use SAE-140 gear oil. 7. Propel er s a t umversa Jam s: Remove fitting and replace plug. Window regulator: Remove door panel and lubricate regulator slide. Use a viscous chassis lubricant.
28.
LUBRICATION
Section B Page 17
LUBRICATION CHART
L-200 SERIES TRUCKS
Spring pins (Both sides) Steering gear relay lever
(10)-_
(7)
(11)
Steering knuckles (Both sides)

Front wheel bearing
(Both sides)
Steering gear Tie rod ends (Both sides) Air cleaner
(14)
Starting motor Spring pins (Both sides) Clutch and brake pedals Battery
(S- 10)
(3-20)
Master cylinder Universal joint Center bearing Parking brake linkage Universal joint
I I I
[Auxiliary spring end (Both sides)
(10)
Spring pins (Both sides) Slip joint Rear wheel bearings (Both sides) Universal joint Differential Door hinge Spring pins (Both sides)
8-4747
PRINTED IN UNITED $TATES OF' AMERICA

L-200 SERIES TRUCKS
1. Engine: Keep crankcase filled to correct level with high-grade engine oil. Changing oil regularly will remove accumulated dirt. Cole
weather requires frequent oil change because of increased use of choke, also condensation of moisture. Refill capacity, '; quarts: add 1 quart for oil filter. For trucks in multi-stop, or other services where sustained high engine speeds are not encountered, select oil grade as follows:
* 90 0 0
TEMPERATURES OIL GRADE (F.),and up , . . . . . . . . . . . . . .. SAE-40 32 (F.) to 90 0 (F.). . . . . . . . .. SAE-40 (* See Hot Climate - High Speed instruction following)
TEMPERATURES OIL GRADE 10 0 (F.) to 320 (F.) (above zero) . . SAE-20W Minus 10 0 tF.) to 10 0 (F.) above zero . . . . . . . . . . . . SAE-IOW
Temperatures lower than minus' 100 (F.) below zero, use SAEIOW plus kerosene. SAEIOW may be safely diluted with colorless kerosene up to 30 percent; mix: thoroughly before adding to engine, and check oil level OFTEN because kerosene evaporates rapidly at crankcase temperature. Hot Climate - High Speed: For trucks operating on highway, or other service demanding sustained high engine speeds, use engme oil havmg a viscosity as near SAE40 as possible and as starting ability will permit. Note: High viscosity oils are available which also have very good cold-pour characteristics. 500 TO 1.000 MILES 2
Oil
['it
1
{Change cartridge when oil has darkened. Remove filter cover and cartridge, clean inside of filter er. Run engine for a few minutes and check filter for leaks.
install new cartridge.
For engine air cleaner remove reservoir and dispose dirty oil; clean filter and reservoir' and refill to oi11evel mark 3. Air cleaners: with clean engine oil! same grade used in crankcase. For hydrovac air cleaner ... remove cleaner, dismantle and clean { parts in a cleaning solvent and allow to dry; saturate element with a light engine oil and replace parts. 4. Battery: Check water level. If necessary, add pur e distilled water to 3/8 inch above plates. 5. B Do not overfill.
k t li d {Cheek fluid level. Do not allow dirt to enter. If necessary, fill to 3/4 inch from top with a high grade auto ra e mas er cy n er; motive type brake fluid. Do not overfill.
6. Steering gear relay arm:} 7. ~ringlpi:s: For'ce a viscous chassis lubricant or SAE-140 gear oil into fittings until old lubricant, dirt and water are 8. expelled. 9. Trea;o~~: s: 10. Auxiliary spring ends:
II. Clutch release fork Shaft:}use a viscous chassis lubricant or SAE-140 gear oil. Do not over-lubricate. Too much oil on knuckles, 12. Clutch and brake pedal: and on clutch shaft will cause failure of brake and clutch lining. 13. Steermg knuckles:
14. Parking brake linkage: }L Ub ' t ~ I' k age, c 1 " plns, PIVO plns, an d SI'd'Lng sur f aces WI t h 't' ' engIne 01 'I Carburetor linkage! d r~c~ 1n eVlS 1 I Door hinges, door latches: oor aces. 17. GStenet:ator: t }put IOta 20 drops light engine oil in each cup. ar Ing rna or: 18. Do not over-lubricate.
;0
P ut sUlta l e 1u b ricant on 'b .
Put one drop of light oil on movable contact arm pivot pin. Remove rotor and put two or three drops of light engine oil on felt wick. Apply a light coat of vaseline to the distributor cam and contact arm fiber rubbing blOCK. NOTE: Lubricate 19. Distributor: distributor shaft at overhaul or at 25,OOO-mile intervals. Use SAE-20 engine oil. Use sealing compound when replacing ( lubricant plug. For distributor with grease cup: fill cup with SAE140 gear oil, as required, and turn One turn every 1,000 miles. Put one or two drops of engine oil on governor rotor. 20. Propeller shaft center bearing: Use a medium short-fiber wheel bearing grease (sodium-soap type). 21. Steering gear: Remove pipe plug and inspect oil level every 1,000 miles. 22. Transmission'Refill: C"de No. 1309 - Capacity Code No. 1310 - Capacity Code No. 1311 - Capacity Code No. 1312 - Capacity Diff erential Refill: Code No. 1408 Capacity Capacity Code No. 1416 Code No. 1419 Capacity *Code No. 1414 - Capacity *Code No. 1422 - Capacity 19 19 24 24 18 19 38 22 37 Use SAE-140 gear oil, Keep housing full of oil.
Pts. Inspect oil level every 1,000 miles and keep oil level up to filler plug, using same make and Pts. grade oil as in unit; if same grade is not available, drain, flush and use new oil. (Drain and Pts. flush twice yearly or every 10,000 miles, preferably in the spring and fall.) SAE-90 cold Pts. climate. SAE140 warm climate. For transmission use SCL, EP !;lear oil or multi-purpose gear oil supplied by a reputable refinery. For rear axles (not Eaton) use SCL, EP oil or For Pts. multi-purpose gear lubricant suitable for hypoid axles supplied by a reputable Pts. Eaton axles, use hypoid gear lubricant available as Elco Gear Safety "28" or its (see keep Pts. instructions, section "A"). *For Electric Shift, inspect oil level every 10,000 Pt. filled to plug level with SAE-IO oil.
Pts.
3,000 TO 5,000 MILES
23 . 24.
II h ft I' . . t.{Remove plug and install a pressure-gun fitting. Use a viscous chassis lubricant. Force a small amount rope er s a s Ip Jom. into joint. Note: Too much pressure will damage oil seal and retainer. Remove fitting and replace plug.
1b ' {Remove wheels, clean and inspect bearings, races and wheel hubs. ee earmgs: bearing grease. Replace wheels and adjust bearings.
Wh
Repack bearings, using a short fiber wheel
10,000 MILES W t {Remove plug and install a pressure gun fitting. 25. a er pump: pressure). Use a short-fiber wheel bearing grease and fill housing (under low
26. Hydrovac: Inject two ounces vacuum cylinder oil twice yearly or every 10,000 miles. preferably in the spring and fall.
15,000 TO 20,000 MILES h ft' I ' , t {Remove plug, install a pressure-gun fitting and fill (under low pressure). Use SAE140 gear oil. 27. Propeller 5 a unlversa Jom s: Remove fitting and replace plug. 28. Window regulator: Remove door panel and lubricate regulator slide. Use a viscous chassis lubricant.
PROPELLER SHAFT Index Page 1
PROPELLER SHAFT GROUP
INDEX
Page GENERAL . . . . . . . . . . . . . . . . . . . '.' . . . . . . . . . . . . .

DISASSEMBLY AND REASSEMBLY OF UNIVERSAL JOINTS Cleaning and inspection . . . . . . . . . . .
Lubrication . . . . . . . . . . . . . . . . . . .
Type .. c ................ .
Type "CC", "CRS" ..... . Type 1410 Spicer . . . . . . . . . .
CENTER BEARINGS (PRE-LUBRICATED TYPE) Construction . . . .
Disassembly . .
Reassembly . . . .
CENTER BEARINGS (NOT PRE-LUBRICATED TYPE) Adjustment . . . . . . . . . . . . . . . . . .
Construction . . .' . . . . . . . . . . . . . . . . .
Housing assembly felt seal replacement ..
Installation. . . . . . . . . .......
Lubrication . . . . . . .
Replac ement on shaft . .
PROPELLER SHAFT VIBRATION (DRIVE-LINE) Center bearing . . . . . . . . . . . .
Clutch and flywheel . . . . . . . . .
Companion flanges . . . . . . . .
Correct alignment . . . . . .
Engine mountings . . . . . . . . . . . . . .
Lubrication . . . . . . . . . . . . . . . .
Step-by-step procedure for checking . . . . .
11 11 11
11
6 6
1,2 3,4
5.6
7 7,8 8
9,10 8,9 10 19 10 10
11
11 11,12
PRtNTO IN UNITED STATES OF AMERICA
PROPELLER SHAFT Section A Page 1
PROPELLER SHAFT
PROPELLER SHAFTS AND UNIVERSAL JOINTS

The propeller shafts are of tubular construction, having splined slip yokes and universal joints with steel roller bearings. Front propeller shafts have fixed joints while rear propeller shafts have the slip yoke which allows for vari ations in distance between rear axle and trans mission or center bearing. Universal joints used on L-Line trucks are of several types and sizes, and are illustrated below.
DRIVE
LUG
"CS" TYPE TRUNNION BEARING
Araror
Fig. 3 -- Showing details of the "cs" type joint. On this type joint the "C" type bear ings are secured by means of straps or lock plates.
Fig. I -- Illustration shows details of the "C" type universal joint. with this type joint the four bearings on the journal or cross are al ike.
'!.-22.~ff
Fig. If -- Spicer propeller shaft joint.

"R" TYPE BEARIN
Disassembling (Type C) Joint

To take a joint and shaft as sern.bly out of a chassis, it is necessary only to remove eight capscrews; the four screws that hold the two bearings to the transmission fitting, whether it be fitting yoke or brake flange fitting, or the center joint fitting on a long wheelbase chassis and the four screws that hold the two bearings to the pinion shaft fitting (Fig. 5). To disengage the bearings from the end fittings, compress the slip joint.
Fig. 2 -- Showing details of the NCR" type joint. In this type joint one pair of bear ings is of the "C" type while the opposite pair of bearings is of the OR" type.
Care must be taken to prevent the bearings from falling off the journals of the spider when they have been disengaged from the fitting yokes. It is a good idea to tie the bearings together in place on the spider while the other bearings are

Sometimes, due to the air-lock in the bearings not having been entirely eliminated by compressing the bearings, it is necessary to tap the ends of the bearings lightly with a hammer. This will relieve the air-lock and permit the assembly of the bearings to the yoke without further difficulty. When the key or lug (Fig. l) of a bear ing is seated properly in the keyway of the yoke, the entire face of the bearing will be flat on the face of the yoke. Be sure the entire face of each bearing is flush with the face of the yoke before inserting the capscrews. A single lock plate is used for locking each set of two screws. The screws are to be assembled in the holes of the lock plates before they are inserted in the yoke screw holes. After the screws have been drawn up as tightly as possible, one of the two projecting lips at each end of the lock plate is to be turned up tightly against a flat side of the lock head. It is very important that each screw be securely locked. It is necessary to have perfect alignment of the front and rear joints. Therefore, if either the slip yoke or propeller shaft has been re placed, be sure when assembling these two items that the bearing keyway of the slip yoke is in alignment with the bearing keyway of the pro peller shaft yoke. Due to the design and construction of the drive shaft and universal joint assembly, the replace ment of any part or parts can be accomplished without special tools or garage equipment. Re placements can be made without removing the propeller shaft assembly from the chassis.
Flange type bearing

A.22022
Fi g. 5
being disengaged from the slip yoke and pro peller shaft yoke. This precaution should be taken to eliminate the possibility of dirt or other foreign matter from entering the bearings, provided they are to be used iigain. It requires but very little dirt or other foreign matter in a bearing to cause considerable damage to a joint. Unless the propeller shaft or the slip yoke is to be replaced, it is best not to disassemble these two parts. They are balanced in the position in which they are found, and should remain in that position. When a bearing is removed from the spider, the cork packing washer usually comes off with, and remains in, the bearing. If the joint has given considerable service, the cork packing washers should be removed from the bearing and replaced.
Reassembling (Type C) Joint

All parts should be thoroughly cleaned before they are reassembled. and each bearing should be packed with a small amount of clean lubri cant. (Use a high-grade lightweight semi-fluid chassis lubricant.) Before assembling the bearings to the spider, be sure the four dust shields are in place on the shoulders of the journals of the spider. Place a new cork packing washer on each journal and push it up to the shoulder. Then place the bearing on the journal. Because new cork packing washers are used, and also because a possible air-lock is in the bearings, it is necessary to compress the bear ings in order to get them in the proper location for assembling to the yokes and fittings. After opposite bearings have been compressed as much as possible, a tie wire is to be used to keep them in the compressed position. When all four bearings have been compressed tightly in place on each of the two spiders, these spider and bearing assemblies are then ready for at taching to the propeller shaft yoke and slip yoke.
If a failure occurs in the rear joints, the bearing capscrews can be removed, and the propeller shaft pushed forward in the slip yoke, thereby disengaging the bearings from both the propeller shaft yoke and the pinion shaft yoke. The re assembling of the joint is no more difficult then disassembling. Less difficulty will be ex perienced in the reassembly if the bearings are assembled to the propeller shaft yoke first.
The same procedure is to be followed in dis assembling, replacing parts and reassembling the front slip joint, the only difference being that the slip yoke is pushed back on the propeller shaft. The best results will be obtained in the reassembly of this joint if the bearings are first assembled to the slip yoke.
If the slip yoke or propeller shaft has been damaged and must be replaced, these two parts can be disassembled merely by removing the slip yoke grease retainer or cap. In such in stances it is necessary to be very careful when reassembling the shaft and slip yoke that the bearing drive lugs of the slip yoke are directly in line with the bearing drive lugs of the pro peller shaft yoke. Arrows stamped on the pro
Slip yoke
Splined stub
the bearing. The cross IneInber then can be reInoved froIn the yoke without any difficulty. Should any of the working parts be worn, they should be renewed with a new cross and four cOInplete bearing asseInblies. In handling these parts, be sure that the trunnions of the cross are clean and that no dirt gets into the bearings be fore they are asseInbled into the joint.
It is always advisable to replace the old cork
Alignment arrows
A22023
Fig. 6
peller shaft and slip yoke indicate the correct position for asseInbly. THESE ARROWS MUST MATCH (Fig. 6).
sealing washers on each of the trunnions, which serve to prevent the ingress of dirt and retain the lubricant in the bearing units.
Reassembling (Type CR, CRS) Joints

Before asseInbling the bearings, be sure that there is lubricant in each one, then proceed as follows: Rest one of the yoke forks on a flat piece of iron, leaving the other fork IneInber freely suspended below, then drive one of the bearings in, so that
Disassembling (Type CR, CRS) Joints

DisasseInble propeller shaft joint using follow ing procedure: ReInove the propeller shaft froIn the truck by taking out four capscrews at each end holding the flange type bearings to the fitting yokes, being careful not to let the flanged bearings fall off and perInit foreign Inatter to enter the rollers. ClaInp the propeller shaft in a vise and reInove the flange bearings (two at each end). The reInaining bearings are cylindrical in shape and fit into bore in the yoke arIns. There are snap rings fitting in grooves of the bearings which locate theIn on the inside of the yoke arIns. These snap rings can be reInoved, as shown in Fig. 7, by Ineans of a punch placed against an end of the snap ring loop and then tapping the end of the punch with a haInIner, until the ring COInes off the bearing. After all of the snap rings have been reInoved, the asseInbly can be placed on parallels, or in a vise, as shown in Fig. 8, with the trunnions of the cross resting on parallels on the vise jaws and the yoke IneIn ber s suspended. By striking the suspended yoke, as shown, the yoke IneInber will be driven down until it COInes in contact with the cross. This will leave the bearing protruding, as shown. After one of the bearings has been driven out in this way, the cOInplete asseInbly should be turned over, and the saIne operation repeated, to drive the opposite bearing out part way. This leaves both bearings protruding frOIn the yoke. The next operation is to claInp the end of a pro truding bearing in a vise, as shown in Fig. 9, and then proceed to strike the yoke IneInber until the bearing is cOInpletely released froIn its snug fit in the yoke. Turn the asseInbly around, claInp the other bearing in the vise in the saIne Inanner as before, and drive yoke IneInber froIn
Fig. 7
Fig. 8
or
AMERICA

After the first snap ring is in place, the asseInbly should be turned over, as shown in Fig. 12, having the one assembled snap ring at the bottoIn and resting the yoke on the flat iron surface, then striking the bearing on the top, driving the upper bearing down, which carries the lower bearing with it. until the snap ring rests securely against the Inilled surface of the yoke fork. After this is done. put in the opposite snap ring, and the joint is ready for service.
Fig. 9
the open end COInes flush with the inside of the yoke fork. Insert the cross through the opposite hole without the bearings, and swing in place and down into the partially assembled bearings. Turn the asseInbly over, resting the above partially assembled bearing on the flat surface, and drive in the other bearing (Fig. 10).
Fig. II
Fig. 10
By continuing to tap the bearings, they will both find their seats against the ends of the trun nions and will CaIne approxiznately flush with the outside of the yoke. After this is done, it is possible that there will be SaIne off-center condition between the cross and the yoke. This is an advantage, because it permits driving in the snap ring on the side that gives the Inost clearance. This is shown in Fig. 11.
Fi g. 12
L-L1NE "MOTOR TRUCK SERVICE MANUAL

Disassembling (Type 1410 Spicer) Joint
a, Remove oil seal retainer from end of slip joint and remove slip joint assembly from shaft, When replacing slip joint, make cer tain that arrows on shaft and joint are in line (Fig. 13).
b. Place joint assembly in vise using soft jaws to protect the joint threads, Remove needle bearing assembly from journal or cross (Fig, 14). c. Using a small punch,_ tap end of needle bear ing assembly to loosen snap ring. Move needle bearing only enough to break bearing assembly away from snap ring (Fig, 15). d. Remove snap ring from slip joint or yoke. Turn joint over and remove opposite snap ring Fig. 16). ( e, Tap needle bearing until opposite needle bearing is free of yoke; using a soft round drift (brass) with flat face about 1/32" small er than the diameter of the hole in the yoke to prevent damage to the bearing (Fig. 17).
Fig. 15
~.-22718
Fi g. 16
Fi g. 13
Drift (brass) - -....
Needle _ _- - I I " Bearing
Needle Bearing------...,;
Fig. I~
PRINTED IN UNITED STATES OF AMUUC"
Fig. 17
PROPELLER SHAFT Section A Page 6 f.

Cleaning and Inspection
1. CLEAN ALL PARTS--Use a suitable clean
ing fluid. Allow the parts to remain in t.he cleaner for some time to loosen up any' particles of grease or foreign matter. Remove any burrs or rough spots from any machined surfaces. 2. NEEDLE BEARING--Do not disassemble. Clean with short stiff brush and blowout with compressed air. Work a small quantity of lubricant (140 S.A.E. Oil) into each needle bearing and turn the needle bearing on the trunnion to check wear. Replace if worn.
Turn yoke or joint over and tap on exposed end of journal or cross end to remove re maining needle bearing (Fig. 18). Remove journal cross from yoke. Tip cross as shown in Fig. 19, and lift out of yoke.
g.
Drift - - - - - -......
Journal - - - - -....
Needle
Bearing
3. JOURNAL CROSS--Because worn needle bearings used with a new journal cross, or new needle bearings used with a worn journal cross, will wear more rapidly (making another replacement necessary in a short time) always replace the journal cross and four needle bearings as a unit.
Fig. 18
4. JOURNAL AND BEARING KIT--To facilitate the replacement of journals and bearings, a journal and bearing kit is available. The use of the kit insures having the correct individual parts when required, and saves valuable time.
Reservoirs
Fig. i9
Reassembling (Type 1410 Spicer) Joint
Reassembling is merely a reversal of the fore going disassembling operations. On joints with out a lubrication fitting, repack reservoirs in the journal cross ends with a good grade 0 f semi-fluid lubricant (140 S.A.E.). Make sure the reservoirs in each trunnion are filled. With the rollers in the race, fill the race about 1/3 full.
Lubrication (Slip Yokes and Joints)

Propeller shaft slip yokes are to be lubricated every 3,000 to 5,000 miles. Use viscous chassis lubricant or SAE-140 gear oil. Remove the pipe plug and inject lubricant. Replace the pipe plug. The universal joints are lubricated every 15,000 to 20,000 miles using a viscous lubricant or SAE-140 gear oil. Remove pipe plug and inject lubricant using a low pressure grease gun. Re place pipe plug.

PROPELLER SHAFT CENTER BEARINGS
A-22499
Fig. 20 -- Pre-lubricated center bearing.
Fig. 21
Construction (Pre-Lubricated Type Bearing)

The center bearing used on the L-110 to L-150 trucks is the pre-lubricated, single-row ball bearing type. The bearing is permanently sealed against water or dirt entering into bearing to cause rapid wear. The center bearing is still further protected from dirt and water by three slingers and a dust shield, forming an integral part of the center bearing assembly, The flexibility of the mounting protects the bearing from al1 misaligning forces caused by unevenness of the road and results in the lowest possible bearing resistance, a minimum loss of power, and a distinct reduction in drive-line noises,
Disassembling (Pre-Lubricated Type Bearing)

The prelubricated type center bearing can be serviced without removing the propeller shaft from the truck although a much more satis factory job can be performed by removing the shaft and center bearing assembly from the vehicle. The following illustrations show ser vicing procedure with the shaft removed. Dis assemble the bearing as follows: a. Remove retainer rivets from each side of rear dust shield (Fig. 21). Use a broad nose chisel to remove rear dust shield (Fig. 22). Remove clamp bolt from rear dust shield assembly (Fig. 23). Carefully bend (open) rear dust shield as sembly only enough to remove from the hous ing and shaft (Fig. 24). Apply puller to strap or bracket edge of bearing housing, pull housing and bracket assembly from rubber ring (Fig. 25).
PRINTEO IN UNITED STArES OF AMERICA
Fig. 22
b.
c. d,
e,
A-22501
Fig. 23
Fig.21t
Fig. 26
Fig. 25
Fig. 27
f.
Place puller plates between slinger and rear of bearing and pull bearing with rubber ring and r ear slinger from end of shaft (Fig. 26). NOTE: Make certain that the pulling pressure is exerted on the bearing inner race, or cone, if the bearing is to be reused. The bearing is prelubricated (lubricated at factory) and no further lubri cation is necessary. If the sealing parts (Fig. 27 are damaged during the removal or replacing operation, the bearing is apt to fail because of loss of lubricant.
Reassembling (Pre-Lubricated Type Bearing)

Reassembling procedure is the reverse of the foregoing disassembling operations.
Construction (Not Pre-Lubricated Type) Bearing

g. Remove rubber from bearing (F . 27). When replacing bearing and rubber ring in housing, apply thin coating of soap solution to ring to permit easy entry of rubber ring into housing. The bearing is a press fit on the shaft. Use a short length of tube or pipe slightly larger on its ID than the propeller shaft spline diameter for pressing on the slinger. bearing and rubber ring as sembly and outer slinger. Figs. 28, 29, and 30 illustrate the construction details of the center bearing assembly as used on L-l60 trucks and up. The center bearing is constructed having a double-row tapered roller bearing operating in a special housing in which lubricant channels have been incorporated to assure a continuous flow of lubricant to the bearing.

The assembly is amply provided with shields and slingers to prevent the entrance of dirt and water, and the entire assembly is mounted in a rubber ring to provide insulation from the frame.
Frame cro88member Rubber ring retainer
Installation (Not Pre-Lubricated Type Bearing)

Because of accuracy in manufacture, this bear ing has the proper roller contact and specified end clearance. Always install a complete bearing, rather than separate parts. The Service Parts department will supply only the complete bearing. Make a bench assembly of the bearing, housing, and seals, then install this assembly as a unit. Note that the bearing must be a sliding fit in the housing, and that the seals are installed with the rolled edge of the seal to the inside of the housing. Install housing and bearing assembly, having all nuts hand tight. Permit the engine to drive the propeller shaft at a low idle speed to per mit the bearing housing and rubber ring to center themselves in the carrier. Tighten all mounting nuts.
Tapered roller bearings
A-23452
Fig. 28 -- Center bearing used on L-160 Series.
Adjustment (Not Pre-Lubricated Type Bearing)

FRAME
CROSSMEMBER INSULATOR
Prior to reinstalling a roller bearing of this type, it should be checked for wear or end play. a. Place the bearing assembly in a vise and mount an indicator as shown in Fig. 31. First, spin the bearing in order to center the races and then immediately check for end play by moving cup toward the indicator as shown. Two or three checks should be made to definitely establish amount of end play present. End play should be from .005" to .008" and corrections should be made if amount is in excess of .008".
SPACER
p:-
/~.-J,
~~
Fi g. 29 Series. Center bearing used on L-170, L-180
FRAME / CRDSSMEMBER
Fi g. 31
b. Where indicator shows end play to exceed .008", the bearing should be disassembled, thor oughly cleaned, and the c one spacer measured with a micrometer as shown in Fig. 32. Reduce the cone spacer thickness the re quired amount (indicator reading less .005 ") through the use of emery cloth on a smooth surface, moving the spacer in a circular motion. See Fig. 33. Reassemble bearing and recheck results. See Fig. 34.
TAPERED
c.
ROLLER
BEARINGS
Fig. 30 Series.
Center bearing used on L-190, L-200

d.
PROPELLER SHAFT Section A 10

Center Bearing Lubrication
The lubricant recorrunended for the center bear ing is a medium, short-fibre, wheel bearing grease, the technical specifications of which are a cold-milled sodium-soap type -- not cal cium -- having a work penetration consistency of 250 maximum and which will not work down below 300. The center bearing should be lubricated every 500 to 1000 miles.
Center Bearing Replacement on Shaft

Motor Truck Service Bulletin No. 25, 1941, de scribes in detail the advisability of testing center bearing installation for interfer,ence between the bearing and the fillet on the pro peller shaft. Interference at this point will cause early failure of the bearing.
Center Bearing Housing Assembly Felt Seal Replacement

Fi g. 32
When replacing felt seals in the center bearing housing assembly, they should be tested for fit on the propeller shaft as shown in Fig. 35. A break-away tension of from two to eight pounds is considered satisfactory for a dry seal and shaft (not oiled).
Fig, 33
Fi g. 3q
Fi g. 35

PROPELLER SHAFT (OR DRIVE LINE) VIDRATION
Where drive line vibration is experienced, it will be necessary to inspect the following units as outlined below, before any attempt is made to balance the propeller shafts as described under the heading "Step-by-Step Procedure for Checking Drive Line Vibration". COMPANION FLANGES--The companion flange mounting nuts, and the bolts that attach the shaft to the flange, must be tight to assure drive line balance. The least degree of looseness in the flange mounting nuts, or the shaft attaching bolts, is enough to cause excessive (out-of balance) vibration at high propeller shaft speeds. Where the flange also maintains the adjustment on the rear axle pinion bearings or propeller shaft center bearings, this adjustment is de stroyed because of lack of torque on the nut. When a companion flange is removed from a transmission, center bearing or rear axle, the flange and shaft should be marked so that the flange can be reinstalled in the same position on the shaft. Care should be exercised in the removal or replacement of companion flanges as rough handling such as hammering on the trunnion mounting may bend or distort flange. CORRECT ALIGNMENT--Correct alignment of the universal joints is imperative to efficient torque transmission at high speeds. To assure parallel alignment of the universal joints, arrows are stamped on the shaft end and on the slip yoke. These arrows must be lined up; see Fig. 6. LUBRICATION--When a propeller shaft has been removed from a chassis, proper lubrication is an important part in the re-installation opera tion. Be sure to work a small quantity of lubri cant (SAE-140Gear Oil) into the roller assem blies and make certain that the slip joint splines are also properly lubricated. CENTER BEARING--Tighten propeller shaft center bearing mounting bolts. Should the center bearing insulator be deteriorated or oil soaked, it should be replaced. Loose mount ing bolts or an oil soaked or deteriorated in sulator can cause excessive vibration, ENGINE MOUNTINGS--Tighten the engine mount ing bolts. Should the engine mountings be oil soaked or deteriorated, they should be re placed. Loose mounting bolts, or oil soaked or deteriorated mountings, can cause excessive vibration. CLUTCH AND FLYWHEEL--The light side of the flywheel is stamped with a letter "L" and should be lined up with the arrow or inspection mark (usually a white dab or paint) stamped on the heavy side of clutch. (If no arrow is stamped on clutch, it can be assembled to the flywheel in any position.) If these markings are not lined up, excessive vibration can result.
Step-By-Step Procedure For Checking Drive Line Vibration

Start engine, and with clutch dis engaged and transmission in gear to keep the clutch disc from spinning, bring engine speed up slowly to governed speed to determine if vibration is in engine itself or due to an out-of-balance clutch pressure plate assembly. If only normal vibra tion is evident, disconnect the front propeller shaft at the transmission companion flange and with transmission in direct drive and clutch engaged, slowly bring engine speed to governed speed to determine if vibration is caused by an out-of-balance clutch disc or out-of-balance transmission gears.
If both the above checks show only normal vibra tion, connect the front propeller shaft and use the following step-by-step procedure in balancing the drive line assembly.
Drive line vibration can be checked by road test ing truck, spinning the drive line with truck up on jacks or by pulling the rear axle shafts and spinning the drive line. Before any balance weights are added to brake drum or propeller shafts, disconnect the rear pr opeller shaft at center bearing and rotate shaft 180 0 in relation to companion flange (truck without center bearing rotate shaft at trans mission) reconnect shaft then road test truck or spin drive line and check for vibration.
Place weight in brake drum

flange opposite heavy side of drum
Fi g. 36
If vibration is still present after above changes, on truck with brake drum at center bearing, place a lump of glazer's putty weighing approxi mately one-half ounce at brake drum flanges (See Fig. 36). (A small magnet can be used in brake drum flange in place of the putty, liz ounce magnet can be obtained by removing the magnet from a magnetic drain plug), then road
te st truck or spin drive line and by changing

location of the weight, find the point of least
vibration. Then increase or decrease this weight
at that point to obtain as nearly as perfect a
balance as possible. Weigh the glazer's putty
(or magnetic weight) and install a of steel
of the same weight in the same location by tack
welding weight to inside of brake flange. Hold
weld material to a minimum.
For truck without a brake drum at the center
bearing, use an adjustable hose clamp and a
small metal weight (approximately 1/2 ounce).
Clamp the weight to the rear shaft near the
center bearing and cut off excess material of
band as close to clamp as possible (See Fig. 37),
Then road test truck or spin drive line; then by
moving the weight to various locations on the
shaft, find the point of least vibration. Then
increase or decrease the weight at this point
to obtain as perfect a balance as possible. Mark
location of weight on shaft; remove hose clamp
and weight. Weigh the weight and add 3/8 of an
ounce for clamp screw and nut. Select a piece
of steel of this total weight and tack-weld to
propeller shaft at locating mark. Hold weld
material to a minimum.
Cut off excess material of band

as close to damp as possible
Position weight under hose clamp below clamp screw
Place bose damp and weigbt as dose

to stub end of shaft as possible
A-22905
Fig. 37
For trucks with a single propeller shaft, use an adjustable hose clamp, and a small weight (approximately 1/2 ounce), clamp the weight to the front end of the shaft and cut off excess material of band as close to clamp as possible (See Fig. 37), Then road test the truck or spin the drive line; then by moving the weight to various locations on the shaft, find the point of least vibration. Then increase or decrease the weight at this point to obtain as perfect a balance as possible. Mark location of weight on shaft; remove hose clamp and weight. Weigh the weight and add 3/8 of an ounce for clamp screw and nut. Select a piece of steel of this total weight and tack-weld to propeller shaft at locating mark. Hold weld material to a minimum. CAUTION: When attaching loose weights to propeller shaft with hose clamps (when checking for vibration,) make sure that weights are clamped se curely to shaft to avoid hazard of weights flying off.
COOLING SYSTEM & RADIATOR Index Page 1
COOLING SYSTEM AND RADIATOR GROUP
INDEX
Specifications . . . . . . . <~

Page 1-3
SECTION "An
Antifreeze solutions, . . . C leaning the cooling s ys tern Coolant service . . . Cooling system servicing. Draining cooling system General information. Leaks . . Neutralizing Pressure flushing. Radiator cap . . . Radiator mountings. Rust prevention . . . . .
\I
6
3
I
6 6
4
5
2
2 to 6
I
~RIN'rEO
IN UNITED
ST~TES
OF" AMERICA
COOLING SYSTEM SPECIFICATIONS
-----
---
MODEL:
--
L-IIO SD-110 STD.

. -----
L-ll0 L-130 SD-l20 STD. 17

-
L-110
L-ll0 L-130 SD-l20 INCR. 17
__~__ V
L-150
L-153
--
L-150
L-153
SD-110 INCR. IS
V 1
L-160 L-163 L-164 SD-l40 STD. 18

V I
L-160 L-163 L-164 SD-240 INCR.

----~----
L-165 SD-240 STD. &

INCR.
IS
-- V -1
ENGINE: TYPE OF COOLING: COOLING SYSTEM: Capacity (qts.) FAN BELT:

Type
NUInber used
RADIATOR HOSE:
Inlet (upper)
Outlet (lower)
SD-2l0 STD. IS
V 1
17
V 1
IS
V
z [T1
o
~
-~-----l---
1 lxS-7!S 2xfl-13/32
---
o :;:0
-l
:;:0
(")
-l
2xS-7/S 2xll-13/32
2xS-7/S 2xll-13/32
2xS-7/S 2xS-7/S
2xll-13f32
2xll-13j32
--
2x8-7/S 2xS-7/S 2.xll-13/32 2xll-13f32 .

---
lxS-7/S 2xll-13/32
--
I.H.: Core nUInber 1-25/32 Thickness Fins per inch 7 Shroud dia. -- lS-1/2 Fan __________________ 16-2So ----1:21-1 Pulley
---
7::
(f)
1-25/32 7 18-1/2 -17x30 0 1 :ll-1
--
-1-25/32 9 lS-I/2 17x30 o 1.21-1
2-9[32
8
18-1/2
17x30 o 1.21-1
3
2-9/32
2-9/32
3 S
S
<]
9 20
20
20
20 TS-f/2x30 u
IS-1/2x30 o
IS-1/lx30 o
lS-1/lx30 0 1.21-1
1.21-1
1.21-1
1.21-1
--
[T1
:;:0
n
[T1
<
--1-25/32 7 IS-1/2 17x30 u I.l1-1 l-l5/32 2-9/32 8 18-I/l 17x30 v 1.21-1
MODINE:
Core nUInber
Thickness
Fins per inch
Shroud dia.
Fan
Pulley
---
:P
~
1-25/3l
7
:-9/32
9
lS-1/2 17x30 o 1.21-1
lS-1/2 l.l)xl8 u I.l1-1
8
20
IS-Illx30 u
1.21-1
2-9/32
S
lO
18-1/lx30 o 1.21-1
3 9 lO IS-1/2x30 o 1.21-1
3 9 20 18- 1/2x3()O 1.21-1
:P r
o
a
I:Il "0
(1
McCORD:
Core number
Thickness
Fins per inch
Shroud dia.
Fan
Pulley
1-3/4 7 lS-1/2 16xl8 1.l1-1
1-3/4 7 lS-1/2 17x30 o 1.21-1
1-3/4 8 lS-1/2 17x30 o 1.21-1
2-1/4 8 IS-I/l 17x30 o 1.l1-1
3 2-1/4
2-1/4 S
S-1/2 9 20
20
20 IS-1/lx30 o
18.... 1/2x30 o
18-1/2x30 o 1.l1-1 1.21-1
I.l1-1
~?:ll:ll
Z Cl
t"'
20
lS-IZlx30 o
1.21-1
~nHI-j
OQ ....
:::;>>< .... tj I:Il
roo;::"
I-{Il?:l~
Pl~>M I-j!;;7
-----------

_....
- . -...- .
"den!Alc)
OQ~tjO
(11 ..........
1'l:I
--.~-
.....
~-
.......
~-
..
>0 rN~> . . .
........
........
MODEL: ENGINE: TYPE OF COOLING: COOLING SYSTEM: Capacity (qts.) FAN BELT: Type Number used RADIATOR HOSE: Inlet (upper) Outlet (lower) . I.H.: Core number Thickness Fins per inch Shroud dia, Fan Pulley MODINE: Core number Thickness Fins :eer inch Shroud dia. Fan Pulley McCORD: Core number Thickness Fins per inch Shroud dia. Fan Pulley
I
!
LB-I40 SD-110 STD. &: INCR.
LM-IlO LM-l50 SD-ZZO STD. 17

V
LM-IlO LM-I50 BD-l69
L-I70-3-4 L-180 ... 3-4 LF-170 LF-180 BD-l69 STD.
L-170-3-4 L-180-3-4 LF-170 LC-I80 BD-l69 INCR.

II
L-175 BD-l69 STD. &: INCR.

II
L-IS5 L-190 L-193 L-194 RD-372 STD. lS

V
L-lS5 L-190 L-193 L-194 RD-372
!!OCl !AI en
>-1Z
o' ::l
II>
.< en
l1:"
>-1 t'1 ~
r;
INCR.
INCR. 18
V
C
[T1
. . ,.
"'
..
..
l8
V
o -1 o
~
I
lx8-7!8 lx8-7!8 lx8-7/8 lx13-1!4 lxI3-1!4 lx11-1/l lx13.:.!L4 lxII-Ill lxll-13/32 lx11-13/3l lxl1-13/3l 2xIO-13!3z lxlO-13/3l lxlO-13/3l. l-1/8xI3-1/16 l-I/8x13-1/16 SI03-1-1 3 10
-1
::::0
(J
r:
{fJ
[T1
I
.
3 9 20 I 18-I/lx30 o
I-l5/3l
7 18-1/l 17x30 o 1.21-1
l-I/4
8 ' 18-l/l . 17x30 o 1.21-1
l-I/4
7 18-3/4 17-3/4x35 0 1.11-1
1.l1-1
3 9 18-3/4 17-3L4x35 1.11-1
3 9 18-3/4 17-3/4x35 0 1.11-1
22-1/l
lOx30 o 1.13-1
ll-l/l
lOx30 o 1.3-1
()
[T1
<
~
I
ZO
0
3 9
1-l5/3l
l-I/4
8 lS-1/l 17x30o 1.21-1
I I
I
18-1/Zx30 1.21-1
7 lS-1/l 17x3O o
1.l1-1
3 3 7 9 9 lS-3/4 IS-3/4 18-3/4 17-3j4x35 17-3/4x35 17-3/4x35 1.11-1 1.11-1 1.11-1
l-9/3l
3 S
3 10
:t> z c :t>
r
ll-l/l
lOx30 o 1.13-1
ll-l/l
lOx3O o 1.3-1
3 9 lO lS-1I2x30 o 1.21-1
I
1-3/4 7 lS-l/l 17x.;Ou 1.21-1

j
l-I/4
S lS-l/2 17x30 o
l-l/;r
7 18-3/4 17-3/4x35 0 1.11-1
I I
1.l1-1
3 9 18-3/4 17-3/4x35 0 1.11-1
3 9 18-3/4 17-3/4x35 0 1.1l-1

I
3 S 20x30 o 1.13-1
22-112
3 10 22-1/2 20x30 o 1.3-1

-
--_
....
---
MODEL: ENGINE: TYPE OF COOLING: COOLING SYSTEM: Capacity (qts.) FAN BELT: Type Number used RADIATOR HOSE: Inlet (upper 1 Outlet (lower) LH.: Core number Thickness Fins pe r inch Shroud dia. Fan Pulley MODINE; Core number Thickness Fins per inch Shroud dia. Fan Pulley McCORD: Core number Thickness Fins per inch Shroud dia. Fan Pulley
L-190 L-194 L-195 LF-190 L-200 L-204 RD-406

---
L-190 L-194 L-195 LF-190 L-200 L-204 RD-406 INCR. 28

V 2
-------
L-200 L-210
---
L-200 L-210 RD-450 INCR. 28
L-220 L-225 R-6602 STD. 8:: INCR.
RD-450 STD. 28
V 2
---
LD-230 LD-230 - - -r - - - - - - HRBB-600 NHB-600
--STD. 8:: INCR. STD. 8:: INCR.
STD.
----
r;
C
[T1
--
----
28
V 2
3;:
o
C
~
~
-!
2xll-1/2 2xll-1/2 2xll-1/2 2xll-l/2 2-1/8x13-l/16 2-T/8x13-1/16 2-1/8xI3-1/l6 2-1/8xI3-1/16
----
~
(')
--3
3 3
A
(J)
---
8103-3-1 3 8 22-1/2 o -- 20x30 1.13-1
8103-1-1 3 10 22-1/2 20x30 u 1.3-1
---
---
8103-1-1 3 10 22-1/2 30x30 o 1.13-1
8103-1-1 3 10 22-1/2 21x30 u 1.3-1
[T1
n
[T1
<
----
z
3 10 22-1/2 20x30 o 1.13-1
3 10 22-1/2 2lx30 o 1.3-1
3;:
3 8 22-1/2 20x30 o 1.13-1
3 10 22':'1/2 2Qx30 o 1.3-1

------
3
-c------
(j
--
o o t' ....
-----
---
'd
til
(}
Z
til
___
8 22-1/2 20x30 o -------cT3-1

-~--
3 10 22-1/2 20x30 o 1.3-1
3 10 22-1/2 20x30 u 1.13-1
3 10 22-1/2 2lx30 o 1.3-1
~ ~ til ~ ><
.....
't!0t-<J1 Pl~;J>M OQ ..... J1!:l"

~goi'>l
W{l)::ct~
----
COOLING SYSTEM & RADIATOR Section A Page I
COOLING SYSTEM AND RADIATORS
COOLING SYSTEM AND RADIATORS Rust Prevention

(Also see "Cooling System Servicing"
paragraphs.)
One of the common causes of engine over heating is a rust-clogged cooling system. Rust is the result of water action on steel and iron when air is present. Scales originate from impurities in the water used in cooling system. Rust and scales interferes with circulation and cooling, causing overheating. Rust and corrosion formation can be pre vented by maintaining full strength corrosion protection at all times. For rust protection during the winter months, a fresh filling of an anti-freeze con taining an effective corrosion preventive should be installed in the fall. In the spring, drain and discard the old anti-freeze solution because the cooling liquid may have become contaminated by corrosive impurities during use, and the rust preventives or "inhibitors" in the anti freeze solution may have become weakened and exhausted in continual driving. During the summer, a rust preventive should be added to the cooling system to protect the systern against corrosion during warm weather operation. This inhibitor solution should be drained in the fall and a fresh filling of chemically treated anti-freeze solution again installed. Hno commercial cleaning solution is avail able, dissolve about 4 pounds of ordinary wash ing soda in sufficient wa te-r to fill the complete cooling system. Leave radiator filler cap off and run engine for about 1/2 hour or until en gine gets hot. Then drain and flush thoroughly with clean water. When draining the cleaning solution, dis ... connect the radiator outlet hose, as large par ticles of sediment will not pass through the drain cock. If radiator is clogged with insoluble salt formations it should be taken to a reputable concern specializing in the removal of such formations. Reliable radiator service stations are familiar with local conditions and are equipped to apply the proper treatment.
Draining Cooling System

paragraphs.)
During freezing weather, if anti-freeze solutions are not used, the entire cooling sys tem should be drained when truck is not in use. On the Silver Diamond and Blue Diamond Series engines, it is necessary to rernove the pipe or drain cock located on the right side of the crankcase between the generator and starter. On the Red Diamond and R-6602 engines this plug is located on the right rear of crankcase. Opening the radiator drain cock on these engines will only drain the water that is in the radiator and cylinder head, leaving the water jackets in the cylinder block, full, and if freezing occurs, damage to the block will result. Be sure to replace plug (or close drain cock) before refilling system. Engines should be level when drained in order that all water in the system canflowout. BE SURE TO REFILL COOLING SYSTEM BEFORE STARTING ENGINE.
Cleaning The Cooling System

paragraphs.)
Approximately twice a year, or oftener, depending upon kind of cooling water used, the cooling system should be drained and thoroughly flushed out. This is particularly important before using an anti-freeze solution. Unless the cooling water is treated with a corrosion preventive, rust and scale will even tually clog up passages in radiator and water jackets. This condition is aggravated in some localities by the forrnation of insoluble salts from the water used. Cleaning solutions are available which have proven very successful in removing the accumulation of rust, scale, sludge and grease. These solutions should be used according to the manufacturer1s recommendation.
PRINTED IN UNITED STATES Of' AMERICA
Anti-Freeze Solutions
IMPOR TANT: Do not under any circum stances use Honey -- Salt -- Kerosene -- Glu cose or Sugar, in the cooling water as an anti freeze. These at the best are poor substitutes and will cause trouble due to corrosion, clogging of the system, and deterioration of the rubber hose connections. Use only anti-freeze solu tions manufactured by a reputable concern. Before installing any anti-freeze solution the following items should be checked:
COOLING SYSTEM & RADIATOR Section A Page 2

Radiator Cap (Pressure Type)
Radiator caps of pressure-sealing type, as shown in Fig. 1, are useq to hold the cooling
1. Tighten all water connections. Hos e con nections should be in good condition inside and out.
2. Inspect water pwnp for leaks. A leaking water pUIl1p indicates need of water pwnp over-haul sinceno packing nut or adjusting seal is provided. 3. Adjust fan belt to proper tension. Replace if necessary. 4. Drain and clean cooling sys teITI.
Radiator filler neck

,
I
Radiator Mountings
For detailed inforITIation on radiator ITIountings and installations, see illustrations (Fig. 2 to 6 inclusive) covering all L-line trucks. Mounting insulators are required to provide a specific aITIount of flexibility in radi ator ITIounting, otherwise preITIature failure will result.
Vacuum inlet route Pressure release route

Fig, I - Radiator Cap (Pressure Type).
Radiator core
HOle clamp
HOle.inlet
~
,
I
\\
Hose damps
Hose outlet
I ',- ,U
!
/;
Brace (mounted on left side for L. H. drive, and on rigbt side for R. H. drive)
Support cronmember
Brace (mounted on rigbt side for L. H. drive, and on left side for R. H. drive)
Fig. 2 - Radiator Mounting, L-IIO, L-120, L-130,
LB-I~O.

system lUlder a slight pressure, increasing the boiling point of the cooling solution, and pre venting loss of the solution due to evaporation and overflow, The cap has a spring-loaded valve, the seat of which is below the over-flow tube in the filler neck. This prevents the escape of air or liquid while the cap is in position. When the cooling system pressure reaches a predetermined point, the cap valve opens and will again close when the pressure drops to the predetermined point. This cap is also equipped with spring loaded valve, to release the vacuum during the cooling period while engine is not in us e. The vacuum valve releases at approximately 5/8 pounds per square inch. When removing the pressure-type cap from the radiator, perform the operation in two steps. Loosening the cap to its first notch raises the valve from the gasket and releases the pres sure through the over-flow pipe. In the first
stage position of the cap, it should be possible to depress the cap approxhnately 1/8 inch. The prongs on the cap can be bent to adjust this condition. Care must be taken that the cap is not too loose, as this would prevent proper sealing. In removing .the cap loosen it slowly, and then pause a moment. This will avoid possible burning by hot water or steam. Then continue to turn the cap to the left until you can remove it.
NOTE: REMOVE CAP WHEN DRAINING COOLING SYSTEM TO ASSURE PROPER DRAINING.
Cooling System Servicing

1. CLEANING:
(a) Coolant shut-off cocks to heaters and other accessories should be open to allow complete circulation during cleaning, flushing, and draining. Run
FiDercap (preuure type) Radiator core
~ ~
~~~---~~~~==~~~
Sbock absorber bracket
Core support ass' y
.rv.~: II ,I
ti J
Radiator mounting \ brackets U
Drain cock
84743
Fig. 3 - Radiator Mounting, LM-120, LM-J50.


ator core with bare hands to check for cold spots. and watch temperature gauge. When there is no change in temperature for some time, drain the cleaning solution. (g) If clogging of core is relieved but not fully corrected, allow the engine to cool, pressure-flush the system (step 3 below), and repeat cleaning opera tion. (h) If clogging of core, indicated by low temperature spots on core, is not re lieved, radiator core mustbe removed for mechanical cleaning. Mechanical cleaning requires removal of upper and lower tanks and rodding out the accumulated rust and scale from the water passages of the core. 2, NEUTRALIZING: (a) Allow engine to cool, close drain cocks, and pour neutralizer compound into radiator. Use as directed. Fill sys tem with water. (b) Run engine. with radiator covered if necessary, until radiator reaches operating temperature (l60 0 F to 0 180 F).
the engine, with radiator covered if necessary, until temperature is up to operating range (160 0 F to 180 0 F). Stop engine, remOve radiator cap, and drain system by opening drain cocks in radiator and cylinder block. (b) Allow engine to cool, clos e drain cocks, and pour cleaning compound into radi ator according to directions. Fill sys tem with wa ter . (c) Place a clean drain pan to catch over flow, and use to maintain level in radiator. Do not spill solution on vehicle paint. (d) Replace radiator cap. and run engine at moderate speed, covering radiator if necessary, so that radiator core reaches a temperature of 180 0 . F or above. but does not reach boiling point. Allow the engine to run at leas t two hours at 180 0 F so that c'leaning solu tion may take effect. Do not drive vehicle or allow liquid level in radia tor to drop low enough to interfere with circulation. (e) Stop engine as often as necessary to prevent boiling.
() With the engine stopped, feel the radi-
Radiator core
FiBer cap (pressure type)
Brace (mounted on left side for L. H. drive, and on right side for R. H. drive)
Core support an'y.
Brace (mounted on right side for L. H. drive, and on left side for R. H. drive)
11-4742
Fig. q - Radiator Mounting, L-150, L-153. L-ISO. L-IS3. L-ISq. L-165. LC-160.

(c) Drainthe systembyremoving radiator cap and opening drain cocks. 3. PRESSURE FLUSHING: ( e)
COOLING SYSTEM &: RADIATOR Section A Page 5
Continue filling radiator with water and applying air pressure as above until the water COmes out clear.
(a) Disconnect the upper radiator hose which connects radiator core to engine water outlet and remove thermostat from engine water outlet.
Clamp a "convenient length of hose to radiator core outlet opening, and attach another suitable length of hose to the radiator inlet opening to carry away the flushing stream.
(f) Clamp the flushing gun nozzle firmly to a hose attached securely to the en gine water outlet opening. Fill engine block with water, partly covering water inlet opening to facilitate com plete filling.
(g) Turn on compressed air to blowout

water and loose sediment. Continue filling with water and blowing out with air until flushing stream comes out clear.
(c) Connect flushing gun to _compressed air and water pressure, and clamp the gun nozzle to the hose attached to the radiator outlet opening. (d) With radiator cap on tight, fill core with water. Turn on air pressure in short blasts to prevent core damage.
(h) For badly clogged engine water jackets that do not respond to regular pres sure flushing, remove engine cylinder head and core hole plugs and, with a suitable length of small copper tubing attached to the flushing gun nozzle, flush water jackets through openings.
Radiator core
Hoseinlet
I
I
IfHose clamps Fan hood
"Pal" lock nut Drain cock

A22637
Support insulators
L-170, L-173,
L-17~,
Fig. 5 - Radiator Mounting

L-175, LF-170, L-180, L-183,
L-18~,
L-185.
PAINTED fN UNITED STATES OF AMERIC-.

NOTE: After tightening cylinder head on valve-in..head engines it will be necessary to recheck valve stem clear ance. Adjust, if necessary. 5. COOLANT SERVICE: (a) Whe.n servicing for summer, fill sys tem with clean water and add rust inhibitor compound. Use as directed. (b) When servicing for winter, refill sys tem with clean water and sufficient antifreeze solution for protection to lowest temperature likely to be en countered.
(i) When vehicle is equipped witha heater connected to the cooling system, flush the heater, following same procedure as for radiator core.
(j) After completing the flushing opera tion, clean out radiator overflow pipe, inspect the water pump, clean the ther mas tat, and radiator cap control valves. Check thermostat for proper ope ration befor e ins talla tion. (See tl II Engine Section.)
(k) Blow ins ects and dirt from radiator core air passages, using water, if necessary, to soften obstructions.
4. LEAKS:
(a) Before pouring coolant into the cooling system a check should be made for leaks to avoid loss of solution, foaming and corrosion. Check tightness of cylinder head bolts, using tension wrench and tightening to specific num ber of foot-pounds with engine hot.
Radiator core
6. GENERAL INFORMATION:
(a) Never mix cleaning solution with in hibitor or antifreeze compounds.
(b) Before dismantling an engine prelim inary to grinding valves, removing carbon, or rebuilding, always clean the cooling system first.
Hose-inlet
Radiator cap /(pressure type)
~~~------~~------~~
Hose clamps
Fan hood
Hose clamps
Core support ass'y.
Support insulators
A22716
Fig. 6 - Radiator Mounting

L-190, LF-190, L-193. L-19Q, L-195, L-200, L-20Q, L-205, L-210, LF-210.
SPRINGS Index Page 1
SPRING GROUP
SPECIFICA TIONS . . . . . . Page

1-5
SECTION "A"
GENERAL
Assembly of springs. . . . . . . . . . . Auxiliary spring mounting. . . . . . . . Cleaning and inspection. . . . . . . . . . . Disassembly of springs. . . . . . . . . . Front spring mounting. . . . . . . . . Rear spring mounting. . . . . . . . . . . . Rubber bushed spring mounting (front only). Rubber bushed spring mounting (rear only). Spring maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
1
2
2
2
1
2
1
1
. . .
. . .
. .
SECTION liB"
SPRING MOUNTING DIAGRAMS
Page
FRONT Fig. 1 Fig. 2 Fig. 3 SPRINGS:
- Models L-llO, L-120, LM-l20, L-130, LB-140, LM-150 . . . - Models L-1SO, L-lS3, L-l60, L-163, L-l64, L-165, LC-l60. . . - Models L-170, L-l73, L-174, L-175, LF-170, L-IBO, L-IB3, L-IB4,
L-18S, LC-IBO. . . . . . . . . . . . . . . . . . . . . Fig. 4 - Models L-190, L-193, L-194, L-19S, LF-190, L-200, L-204, L-20S, L-210,
LF-210. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1
1
2
2
2
3
3
3
4
4
4
S
S
S
6
6
7
7
REAR SPRINGS:
Fig, S - Models L-llO, L-lZO, LM-120, L-130, LB-140, LM-lSO . . . . . . . Fig. 6 - Models L-1SO, L-1S3, L-163. . . . . . . . . . . . Fig. 7 - Models L-l60, L-l64, L-16S, LC-160, L-170, L-17S. . . . . . . . . . Fig. 8 - Models L-l74. . . . . . . . . . . . . . . . . . . . . . . . . . Fig. 9 - Models L-173, L-IB3. . . . . . . . . . . . . . . . . . . Fig. 10- Models L-180, L-IBS, LC-lBO. . .. . . . . . . . . . . . . . . Fig. 11- Models L-193. . . . . . . . . . . . . . . . . . . . . . . Fig. 12- Models L-184, L-190, L-l9S. . .. . . . . . . . . . . . . Fig. 13- Models L-19S (Timken) . . . . . . . . . . . . . . . . . . . . . . Fig. 14- Models L-l94, L-200, L-20S. . . . . . . . . . . . . . . Fig. lS- Models L-204.. . . . . . . . . . . .. . . . Fig. 16 - Models L-2l0. . . . . . . . . . . . . . . . . . . . . . . . Fig. 17- Models LF-170. . . . . . . . . . . . . . . . . . . . . . . . . Fig. 18- Models LF-190. . . . . . . . . . . .. . . . . . . . . . . . . Fig. 19- Models LF-210. . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION "C"
SHACKLES AND Figs. 1, 2, 3, Figs. S, 6, 7, Figs. 9, 10 Figs. 11, 12 Figs. 13, 14 Figs, 15, 16 Figs. 17, 18 Figs. 19, 20 BRACKETS
4 - Front & Rear for Models L-IIO, L-120, LM-120 . . . . . . . . . 8 - Front & Rear for Models L-130, LB-14.0, LM-lSO . . . . . . Front for Models L-lSO, L-lS3, L-l60, L-163, L-164, L-165,
LC-l60, L-l70, L-l73, L-174, L-l7S, LF-170, L-IBO, L-l83,
L-l84, L-IB5, LC-IBO. . . . . . . . . . . . . . . - Rear for Models L-lS0, L-153 . . . . . . . . . . . . . . . . . . . - Rear for Models L-160, L-163, L-164, L-l6S, LC-160, L-170, L-173,
L-174, L-17S. . . . . . . . . . . . . . . . . . . . . . . . . . - Rear for Models L-IBO, L-183,L-IB4, L-18S, LC-l80, L-190, L-193,
L-195. . . . . . . . . . . . . . . . . . . . . . . . . . . . - Front for Models L-190. L-193, L-194, L-19S, LF-190, L-200,
L-204, L-20S, L-210, LF-210. . . . . . . . . . . . . - Rear for Models L-194, L-200, L-204, L-20S, L-210 . . . . . 1
2
3
3
3
4
4
S
PRJNTEO IN UNITED STATES OF' AMERJCA
SPRING SPECIFICATIONS
-MODELS
-~-"
L-110
--------
L-120
LM-120
L-130
LB-140
L-150
L-153
LM-150
---------
FRONT SPRINGS: No. of leaves

-------
7 42" 1-3/4"
------
9
------ - - - - - - - - - - - -
9 42" 1-3/4" .291" 4-3/8"
8
--------
8
1---
8
46"
2"
.323"
4"
8
46"
2"
.323"
4"
10
-------------
Length (flat) Width Thickness (per Load to bump

~af)
42" 1-3/4" .262" 4"
42"
42"
1-3/4"
.291;1
3-16/16"
42"
---------
1-3/4" .291 "

------------
1-3/4"
-------------~
.262" 4-3/16"
.291" 3-7/8"
3::
4"
~ o
:::0
REAR SPRINGS: No. of leaves Length (flat) Width Thickness (per leaf) Load to bump
8 52"
----
10 52"
11
10 52" 1-3/4" .323" 4-13/16 11
8 52"
--
10
52"
2-1/4"
.360"
3-9/16"
8
50"
2-1/2"
.401"
4-1/8"
10
52"
2-1/2
11
10 -52"
---------------
1-3/4
1-3/4" 323" 4-13/16"
2-1/4" .360" 4-3/8"
(f)
2-1/4" 36 0"
--------
[Tl
:::0
.291" 4-3/8" .401"
4-1/8 11
4"
-------
[Tl
< n
AUXILIARY SPRINGS: Standard

Optional No. of leaves Length (flat) Width Thicknes s (per leaf) Load to bump optional
-------------
optional 5 33"
optional 5 33" 1-3/4"

-----------,-- ---,
op
6
34"
2-1/4"
.262"
3"
optional
-------- - - - -
op 8
33"
2-1/2"
.262"
---------
op
. . . . . <I . . . . . . . .
optional
-----
5 33"
----------
6 32-7/8" 2-1/4
11
6 32-7/8"
------
g"'.,.
"0
(0 ()
tfl
1-3/4
11
1-3/4" .262" 3"
..
. . . . . . . <) 1) ..
2-1/4" .262" 3-3/8"
~tfl
.262" 3"
262" 3"
.262" 3-3/8"
---------------
.................
.,.,.H
g~
,.... '1:J
Q
4-1/8"
..........
_Ultfl
....Z
SPRING SPECIFICA TIONS
~~!:J:j .... H
N~Z
n
'1:IUlUl Pl '1:i '1:1
L-160
L-163
L-164
L-165
LC-160
L-170
L-173
L-174
:;l til
Pl ,.,. ....
Ul
FRONT SPRINGS: No. of leaves Length (flat)

-
8 46" 2-1/4
11
8 46"
-
9 46" 2-1/4" .323"
9 46 11
--
10 46 11 2-1/4"
-
9 46" 2-1/4" .323 11 3-7/16 11
9 46" 2-1/4"
-
10 46" 2-1/4
11
Width Thickness (per leaf) Load to bump
2-1/4" .323" 4-5/16 11
2-1/4" .291" 3-3/4"
t z
.323"
.323 11 3-5/16 11
.323" 3-1/4"
.323 '1 3-3/8 11
[1l
s:
----
4"
3-7/8 11
I
10 52" 2-1/2"
-
o --l o ;;0
;;0
REAR SPRINGS: No. of leaves Length (flat) Width Thickness (per leaf) Load to bump
--l
12 52 11 2-1/2 11 .40 I" 5_1/2

11
8 52" 2-1/2" .401 11 3-7/8

11
8 52"
-
10 52 11 2_1/2 11 .401" 4-9/16"
14 52 11 2-1/2" .40111 6"
12 52" 2-1/2 11 .401" 5-1/16

11
52" 2-1/2"
7\
[1l
2-1/2 11
~---
(f)
.401" 411
.40111
;;0
.401" 4-1/8
11
,--
4-1/2
11
n s:
[Tl
<
:J>
AUXILIARY SPRINGS: Standard Optional

No. of leaves Length (flat) Width Thickness (per leaf) Load to bump
......
~
standard
standard
standard
standard
standard
standard
).>
6 37" 2-1/2" .323 11 411

-
6 37" 2-1/2" .323" 4"
6 37 11 2-1/2 11
-
6 37 11 2-1/2 11 .323 11 --4-1/8"
8 38 11
2-1/2 1'
9
38"
2-1/2"
.201"
-----.291" 4-9/16" 5-1/16"
.323" 3-7/8 11
.....
.... -
SPRING SPECIFICA TIONS
MODELS
L-l
-------
L-183
L-184
~~~~~~~~~~
L-185
LC-180
L-190
FRONT SPRINGS: No. of leaves Length (flat) Width

~~
8 46" 2-1/4"
--------
12 46" 2-1/4" .323" 3-5/16 11
10 46" 2-1/4" .323" 3-5/16 11

-----------
10 46" 2-1/4" .323" 3-5/16"
11 46" 2-1/4"
--------
9 46" 2-1/4" .323" 3-1/2"
12 46" 2-1/4" .323" 3-1/4"

-----------
9 52" 3" .360" 3-5/8"
t: r z [T1
$:
Thickness (per leaf) Load to bump
.323"
-----------
.323" 3-5/16"
3-9/16 11
o -l
;.0
o
C
REAR SPRINGS: No. of leaves Length (flat) Width Thicknes s (per leaf) Load to
.-
-l
10 52" 2-1/2" .401" 4-9/16"
----~~~
10
----------
11 54" 3" 8-.401" 3-.3t>0"

----
13
54" 3" 3-,447" 10-.401"
--~~~
14 54"
~
11 54" 3"
~ ~ ~ ~
11
12 54" 3" 401" 3-3/8"
;.0
32-1/4" 3" 8-.447" 2-.401"
54"
-------
r;
[T1
3" 6-.401" 8-.3600-3-1/8"
3" 8-.401" 3-.360" 3-11 /16"
tn
;.0
8 -.40 1" 3-.360" 3-11/1611
<
n
[T1
3-11/16"
4-1/4"
--------
AUXILIARY SPRINGS: Standard Optional
standard
~~~--
standard
standard
standard
-----------
standard
---------
standard
~~-
------
No. of leaves Length (flat) Width Thicknes s (per Ie Load to bump
8 38"
~ ~~~~~~~-~
7 39" 3"
----------
9 39"
----------
7
---------
7 39"
-----------
7 41" 3" .323" 3-3/8"

IJl '0
39" 3"
~~~~~~~-
2-1/2" .291" 4-9/16"
3"
I~~~
3" .323" 3-11/16"
---------
::;;1Jl
~~
~.
rtl
6-.zgpr
3-11/16"
. 323"
3-.323" 3-1/8"
323" 3-11/16"
'"0
.... gZ Cl vorn(fl
M-H
"0 SPRING SPECIFICATIONS
{lnll
aq(l)::o (l) ~_ H
III '0
"0
..,.::!'!Z
III
nO
MODELS
L-I93
L-194'
L-I95
LF-190
LC-190
L-200
L-204
L-205
.".
.....
o
til
{fl
i:l
FRONT SPRINGS: No. of leaves Length (flat) Width
~.
9 52" 3" .401" 3-3/4"
9 52" 3"
--
8 52" 3"
-
9 52" 3"
-
.......
......
........ ........
9 52 '1 3
11
10 52" 3" .401" 3-5/8"
9 52" 3"
,360"
3-5/8"
r r
I
Thickness (per leaf)
,401" 3-7/16" --
,360" 3-7/8 11
.401" 3-9/16"
.401" 3-5/16 11
[T1
........
3:
o
-l o ::;0
n
REAR SPRINGS: No, of leaves
12 56"
13
12 54" 3" .401"

~-
12 37-3/4" 4" 9-.447" 3-.401"
.......
.0
13
16 56" ---3" .447" 4-7/16 11
13
~ c
7:::
(j)
54" 3"
--
54" 3" .447" 3-1/211
54" 3" .447" 3-3/4"
Width Thickness (per leaf) Load to bum.p AUXILIARY SPRINGS: Standard Optional No. of leaves Length (flat) Width Thickness (per leaf) Load to bum.p
3" 7-.447" .5-.401"
..... 0
.447" 3-1/411
..
,.
'" '" '" '"
< n
[T1
4-3/8"
-
'" '" '" "' '"
. .
3:
z
standard standard
-
).>
standard
standard
standard
I
-~-
.......
8 41" ------3" .323" 3-1/411 7

- --
r
8 41"
-
).>
........
10 41" 3" .323" 4-7/16"
8
41"
3"
.323"
3-3/4"
41" 3" .323" 4-3/8"

--_
......
....... .......
3" .323" 3-1/2 11
.. .. '"
"'
.......
'"
__
'" "' . . . III Ii ..
SPRING SPECIFICATIONS
MODELS FRONT SPRINGS: No. of leaves Length (nat) Width
LC-200
L-2IO
LF-Z10
L-Z20
..
LF-ZZO
~
L-225
L-Z30
LF-230
--
10
--
10 52"
---
10 52"
52" 3"
---
-----3"
---
.-.
------- -----
t:"" C
[Tl
Thickness (per leaf) Load to bump
9-.447" -r::40I" 3-3/4"
9-.447" 1-.40 I" 3-3/411

--
. 401" 3-1/2"
3:
-REAR SPRINGS: No. of leaves

-
o ---1
o
C
:;;0
15
-
12 37-3/4"
---
:;;0
---1
Length (flat)
---
56" 3"
-----
------
Width Thickness (per leaf)
3"
7':
(JJ
.499" 4-3/16"
10-.500"
-Z-:~3-75"
[Tl
----~--
--
-- .._ . _ - - - - - '-
:;;0
Load to bump AUXILIARY SPRINGS: Standard

-
< n
[Tl
st=dard :
-
z
c
-----------
3:
Optional No. of leaves 9
r
~ (l)
-----Length (flat) Width Thirknpss (per leaf)
---
41" 3" 3-.401" 6-.360'

-----
l::;CIl
'"d()~
....
n ,.- '"d
I7Q
Load to bump
4-3/16"
P'e:.H -Z
(l)
g Cl
UlUlVl
SPRINGS Section A Page 1
SPRINGS
Front Spring Mounting

Front springs are mounted at the front with brackets and at the rear by shackles. since this assures the spring leaves being com pressed. Spring pins on the L-line trucks are of three types: 1. Spring pins that are threaded into shackles o;r brackets. 2. Spring pins that are into shackles or brackets. 3. Spring pins that are or pressed in brackets. Spring pins which are threaded into the bracket require that the pin be tightened into the bracket and then backed out one-half turn. The locknut should then be tightened securely and the cotter pin installed. NOTE: Do not back off nut to permit in stallation of cotter pin since this would permit pin to turn in the bracket, and cause excessive wear. If necessary, turn pin out of bracket a slight amount to permit in stallation of cotter pin when the locknut is tight. Spring pins which are to be driven into the shackle or bracket, require that the pin be aligned 50 as to be able to install lock bolt through bracket or shackle with pin in place. Spring pins that are welded or pressed into bracket or shackle require that spring pin nut be tightened securely with knurled side out. This is a self-lock type nut. When installing threaded spring pins in threaded spring shackles, the lubricant hole in the spring pin should be located in an area ap proximately 90 0 on either side of top center of the spring eye or away from the loaded side of the spring pin (See Fig. 1),
Rear Spring Mounting

Rear springs are mounted at the front with brackets and at the rear with shackles.
Auxiliary Spring Mounting

Auxiliary springs are mounted on top of the main rear spring and under load the auxil iary spring ends will contact the brackets at tached to the side rails.
Rubber Bushed Spring Mounting (Rear Only)

On trucks equipped with rubber bushed spring mountings, it is necessary to remove the complete spring assembly to replace the rubber bushings. These rubber bushings are made up of two parts on each pin. To install new bushings, the following instructions are to be used: 1. Remove nuts and washers from bracket pins at front and rear. 2. Remove U-bolts and slide spring off of both front and rear bracket pins. 3. Place spring in vise and remove shackle pin nut and washer. 4. The rubber busnings are separated at the center of each pin, making it possible to remove a half of a bushing from each side of the spring and shackle eye.
5. Install new bushings by reversing the above operation. 6. Application of soap solution to the bushing will facilitate installation of the bushings. 7. When installing nuts on the shackle and bracket pins, the knurled side of the nut must face toward the outside. Tighten spring and bracket pin nuts securely (ap proximately 35 ft. lbs.).
eye
Spring Maintenance
Spring leaf failures at the spring eye are generally a result of improper spring pin ad justment. If the pin is drawn up too tightly in the bracket or shackle, a bind will result. Spring failures at the center section, or near the center bolt hole, are generally caused by loose U-l{olts. These bolts must be kept tight and checked frequently. The best results will be obtained by having the vehicle fully loaded at the time of tightening the U-bolts,
O~
Spring pin
I
{ Lubricant hole closed,load prevents proper lubrication
A-23453
Fig. I - Spring Pin Installation (Diagramatic). With the pin in this position, adequate lubri cation is assured.
AMERICA
SPRINGS Section A Page 2

Cleaning and Inspection of Springs
Wash or scrub all parts in c solvent or clean all parts with steam cleaning equip ment. Brushing of spring leaves with a wire brush will facilitate scale removal. (NOTE: Do not immerse rubber spring bushings in clean ing solvent.) 1. Inspect all spring leaves for breakage and cracks. Replace defective leaves. Inspect all leaves for arch by with new leaves. If leaves are flattened out, either re-arch or replace. 2. Examine spring pins for wear. If wear is apparent, or if pins are corroded or cracked. replace with new 3. Inspect spring eye bushing, and rear shackle bushings for wear, and replace if defective. 4. Inspect spring bracket for breakage and for wear in mounting bolt, or rivet holes, and replace if worn or broken.
Rubber Bushed Spring (Front Spring Only)

To remove rubber bushing from front springs, the following instructions are to be used:
(FRONT END)
nut from spring Remove the bracket. 2. To remove the front spring pin, remove the two bolts and nuts that hold the inside half of the pin bracket to the frame .channel. This will allow the spring pin to be removed with the inside half of the spring bracket. 3. Unless replacement of the spring pin is necessary, do not attempt to drive spring pin out of bracket. This will damage and loosen the pin in the inner bracket eye. 1.
(REAR END)
To remove the rubber bushings from the rear end of front use the following pro cedure: 1. Remove nuts from both rear spring pins. 2. Remove retainer from pins. 3. This will let the inside shackle be removed with both shackle attached.
5. Replace center bolts at each overhaul.
Disassembly of Springs
The disassembly of front or rear springs is identical in procedure. Disassemble springs as follows: 1. Place spring in vise, clamping assembly near center of sp 2. Remove nuts from four spring clip bolts, and remove bolts from clips. 3. Remove nut from center bolt.
Assembly of Front and Rear Springs

I. Lightly coat spring leaves with graphite grease. Replace spring leaves in proper order, lining up the center bolt holes. 2. Partially compress spring leaves, and in sert center bolt and nut.
3. Place spring assembly in vise, and com press spring leaves fully. 4. Install four spring clip bolts in
and install nuts on bolts.
bolt nut.
4. Release vise to
leaves to separate. Remove spring vise. Separate and remove leaves from center bolt.
5. Run over end of clip bolts and center bolt

enough to prevent loosening of nut.
Auxiliary Springs
Disassembly of the auxiliary springs dif fer only slightly from that of the front or rear springs: 1. Place leaves together. in vise, and clamp
Auxiliary Spring Assembly

1. Coat spring leaves lightly with graphite grease. Place leaves one on top of another in accordance with length. 2. Compress spring leaves and install center bolt and nut. 3. Place spring in vise and compress leaves fully. Tighten center bolt nut. Bend down ends of spring clips, being careful not to break them. Heating the clips with a torch will facilitate operation.
2. Straighten tabs of two spring clips, being careful not to break them off. Heating clips with a torch will help avoid breakage. 3. Remove nut from center bolt. and release vise to permit leaves to separate. Remove spring from vise. 4. Remove spring leaves from center bolt.
SPRINGS Section B 1
FRONT SPRING MOUNTINGS
Frame rail Rear bracket Front bracket Vbolt
v-FRONT
Rubber bushing
Shackle
r_i.. - ,......., ~~-E'---___ Axle I-beam
Wedge plate
A-21S00
Fig. I - Models L-IIO I L-120, LM-120, L-130, LB-ILl-O, LM-ISO.
l1li(
Front Clip
Ubolt
Bumper
Ubolt seat
A-21S14
Fig. 2 - L-ISO, L-JS3, L-160, L-163, L-16Lj., L-16S, LC-160.
Center bolt
U-bolt seat
Lock washer
C::_'-::;'.;f--- Axle
Ibeam
A21518
FRONT
Fig. 3 - Models l-170, L-173, L-17Lj., L-17S, LF-170, L-180, L-183, L-J8Lj., L-185, LC-IBO.
PRINTEO IN Uf',l,1'D STATES OF AMERICA
SPRINGS Section B Page 2

0( Front
U-bolt seat
Bumper
Vbolt
Center bolt
Wedge Vbolt nut
Lock washer
~_~ Axle Ibeam

FRONT
A-21S13
Fig.
- Models L-190, L-193,
L-19~,
L-19S, LF-190, L-200,
L-20~,
L-205, L-210, LF-210.
REAR SPRING MOUNTINGS
Rear shackle Front bracket Cross member
Rear bracket
A-21S23
REAR
Fig, 5 - Models L-I 10, L-120, LM-120 (Shock Absorbers-Standard) Absorbers-Optional ).
L-130, LB-140, LM-ISO (Shock
<
Front
Vbolt
~I----l
--,-:---- Spring seat .....::-:,.::-.--- Axle housing
REAR
"----Vbolt plate
A-21S03
Fig. 6 - Models l- 150, L-153. L-163.

Front V-bolt V-bolt seat Spacer
~"'.:::iI-E,--- Lock washer Nut -~.:t"t1J:::::.::::.:::::at , " - - - - V-bolt plate REAR
A-2J5J6
Fig. 7 - Models L-160, L-164, L-165, LC-160, L-170, L-175.
(6)~o~ "- - - - q~:JQ~C~Ii~P?>t~ '- -r: j~U"'~ "c7JiW'111'---=iU:~-~-':I;f+,l:~r-l IP--'~~~~[:JEJ=----l~~~~vftp----'

=:;:::=
tL
C1.,
Auxiliary spring Front
V-bolt seat
~~:=:~~~~~~~~=~~;i:-=- -~~~~~~=l-c:T~~p=--'~:=:r-'==-'
bOIt.7/-C~)1R' Spacer
~
REAR
~ .
Auxiliary center bolt /
oX
Center
V-bolt Axle housing V-bolt plate Lock washer
--i'(
Spring seat Dowel Nut

A-2J5J9
Fig. 8 - Models L-174.
Front
Clip
V-holt
U-bolt seat
Center bolt
Spring seat
- Axle housing V-holt plate ___~--...'\. Nut 't=~=::::/lF?'TI~_ Lock washer

A-2J5J2
Fig. 9 - Models L-173, L-183.

'
Front
Clip
Ubolt
U.bolt seat
Center bolt
U.bolt plate Lock washer

UioE'---- Nut
REAR
Fig. 10 - Models L-180, L-185, LC-180.
III(
A-21510
Front
Center bolt
Spring seat Dowel !-H---Axle housing U.bolt plate Lockwasher LL..I.J""<:""--Nut

A21517
REAR
Fig. II - Models L-193.
Clip Front
U.bolt plate
Lock washer
~"""""'--Nut
A.21502
REAR
Fig, 12 - L-18~, L-190, L-J95.

Clip
Spacer
U.bolt seat U.bolt
front
A-21501
Fig. 13 - Models L-19S.

Front Busbing Bushing
Axle bousing
A-21742
Fig. 14 - Models L-194, L-200, L-20S.

Front Auxiliary spring Ubolt seat Bushing
ra10~
Clip
'Spring
A-21741

0(
Front U-bolt seat Bushing
~Spring
Spring seat
Axle housing
A-21743
SPRINGS Section C Page 1
SPRING SHACKLES AND BRAKES

Bracket
Rubber bushings
[lL.. ___ ~ lu
I I -- --f--.--\+
Nut
oval side
Spring
A-21S09
out
Fig. I - Front Spring Front Bracket For

L-IIO, L-120, LM-120.
Models
A-21522
'I
Fig, 3 - Rear Spring

L-IIO, L-120, LM-120.
Front Bracket For
Models
Bracket~~,i
Pin
ri: 'L
I! :fl __ --0--
I '
_..Li.
I I'
"
Pin
Nut
'r-.~~...:"'~.~-~......
oval side
Rubber bushings
out
Shackle
NUl-oval side oul
,!-oE:.....,..c.~i-i-"-
Shackle
Nut
oval side
out
A-21S08
Washer - - - . , l.....
A21524
Fig. 2 - Front Spring

L-IIO, L-120, LM-120.
Rear Shackle For Models
Fig.
- Rear Spring
Rear Shackle
For Models
L-110, L-120, LM-120.
PRINTED IN UNIT EO STATES OF' AMERICA
n
Nut
Rubber bushings
ovalside
out
Lubricator
A.22942
A23180
Fig. 5 - Front Spring Front Bracket For Models L-130, LB-lqO, LM-150.
Fig. 7 - Rear Spring Front Bracket For Models L-130, LB-lqO, LM-ISO.
Lock pin
Pin
Nut
ovalside out
Bracket
Pin
Nllt---JIIoool'
/::...o~-Pin
Bushing
Spring
A23179
A23181
Fig. 6 - Front Spring Rear Shackle For Models L-130, LB-JijO, LM-ISO.
Fig, 8 - Rear Spring Rear Shackle L-J30, LB-lqO, LM-ISO.
For Models

Bushing
Lock pin
A-23446
Bracket
Fig. II Rear Spring Front Bracket For L- I50 , L- 153

Nut
Models
Shackle pin
Lubricator
A-2151l
Fig. 9 - Front Spring Front Bracket For Models l-150,l-153, l-160,l-163, l-161t, l-165, lC-160, l-170,l-173,l-171t, l-175, IF-170, l-180, l-183, l-181t, l-185, lC-ISO.
~---'--!!'f---
Shackle pin
Lock pin Bushings
A-23445
Spring
Rear Shackle For Models
Lock pin
Bracket pin
.ubricators Shackle pin Bushing
A-21506 A-2'738
Fig. 10 - Front Spring Rear Shackle For Models l-150, l-15a,l-160, L-163, l-161t, l-165,LC-160, L-170, l-173, L-171t, L-175, LF-170,L-180, L-183, L-ISIt, l-IS5, LC-ISO.
PRINTED iN UNITED STATES OF" AMERICA
Fig. 13 - Rear Spring Front Bracket For Models l-160,l-163,L-161t, L-165, lC-160, L-170, L-173, L-171t, L-175.
Bracket lubricator Lock pin Sbackle Lubricator Lock pin--.:J!'
Shackle pin
Spring~-
Bushing
A21139
Lubricator
Fig. l~ - Rear Spring Rear Shackle For L-160,L-163,L-16~, L-165, LC-160, L-170, L-17~, L-175.
Models L-173,
Bracket
Lock pin
A21505
Fig. 17 - Front Spring Front Bracket For Models L-190,L-193,L-19~, L-195, LF-190, L-200, L-20~, L-205, L-210, LF-210.
A21737
Bracket
Fig. 15 - Rear Spring Front Bracket For Models L-180, L-183,L-18~, L-185,LC-180, L-190, L-193, L-195.
Shackle Lubricator Bushing
Lock pin
Bushing
l.ubricators
Lock pin Shackle shaft

A21135
A21520
Fig. 16 - Rear Spring Rear Shackle For Models L-180,L-183, L-18~, L-185, LC-180, L-190,L-193, L-195.
Fig. 18 - Front Spring Rear Shackle For Models L-190,L-193,L-19~, L-195, LF-190, L-200, L-20~, L-205, L-210,LF-210.
A-21S2J
Fig. 19 - Rear Spr i ng Front Bracket for L-194, L-200, L-204, L-205, L-210.
Mode Is
Bushing cubricator
..,.:..,!-+*--- Shackle pin
Bushing
A2'S07
Fig. 20 - Rear Spring Rear Shackle For L-194,L-200,L-204,L-205,L-210.
Models
PAINTED IN UNITED STATES OF AMERle.
STEERING GEAR Index Page 1
STEERING GROUP
The following list shows the L-line truck models and their corresponding steering gear models. Specifications of the individual steering gear models will be found on specifications page 1.
TRUCK MODELS
STEERING GEAR MODELS TA-1Z TA-IZ TA-14 T-14 T-14 TA-14 TA-14 TA-14 TA-54 TA-54 TA-54 TA-54 TA-54 TA-54 TA-54 TA-61 TA-54 TA-61 TA-61 TA-61
TRUCK MODELS
STEERING GEAR MODELS TA-61

TA-61
TA-61
T-66
T-66
T-66
T-66
TA-66 TA-66 TA-66 TA-66

L-110 .. " . . . . . . . . . . . . . . . . L-IZO . . . . . . . . . . . . . . . . . . . . LM-IZO . . . . . . . . . . . . . . . . . L-13 O. . . . . . . . . . . . . . . . . . . . LB-140 . . . . . . . . . . . . . . . . . L-150. . . . . . . . . . . . . . . . . L-153 . . . . . . . . . . . . . . . . . . . LM-150 .............. . L-160 . . . . . . . . . . . . . . . . . . . L-163 . . . . . . . . . . . . . . . . . . . . . L-l 64. . . . . . . . . . . . . . . . . . L -1 65. . . . . . . . . . . . . . . . . . LC-160 . . . . . . . . . . . . . . L-1 70. . . . . . . . . . . . . . . . . . :"'-173 . . . . . . . . . . . . . . . . . . . :"'-174 . . . . . . . . . . . . . . . . . . . . :"'-175 . . . . . . . . . . . . . . . . . . . -,F-170 . . . . . . . . . . . . . . . . . . . .
.... -lBO . . ..1-1 83. . . . . . . . . .
L-IB4 . . . . . . . . . . . . . . . . . . . . L-IB5 . . . . . . . . . . . . . . . . . LC-IBO . . . . . . . . . . . . . . . . . . . . . L -190. . . . . . . . . . . . . . . . . L-193 . . . . . . . . . . . . . . . . . . . L-l94. . . . . . . . .. . . . . . . L-195 . . . . . . . . . . . . . . . LC-l90 . . . . . . . . . . . . . . . .

LF-190 . . . . . . . . . . . . . . . . L-ZOO . . . . . . . . . . . . . . . . . . . L-Z04. . . . . . . . . . . . . . . . . . . . L-Z 05 . . . . . . . . . . . . . . LC-ZOO . . . . . . . . . . .
L-ZlO . . . . . . . . . . . . . . . LF-ZlO . . . . . . . . . . . . . . . . . . L-ZZO . . . . . . . . . . . . . . . . . .
LF-ZZO . . . . . . . . . . . . . . . . .
L-ZZ5 . . . . . . . . . . . . . . . . . L-Z30. . . . . . . . . . . .
LF-Z30 . . . . . . . . . . . . . . . .
TA-70
TA-70
TA-70
INDEX
Page
;pecifications . . . . . . . . . . . . . . .
1
SECTION "A"
l.djustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ;onstruction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Jisassembling steering gear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . lrag links. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 'lstalling steering wheel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . acket tube bea ring. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .eassembling steering gear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .emoving stee ring wheel . . . . . . . . . . . . . . . . . . . . . . . . . . . . tee ring column alignment. . . . . . . . . . . . ................ tee ring gear connection with front wheels . . . . . . . . . . . . . . . . . . . .
1, Z
1
4
6
4, 5
3
3
3
PRINTED IN UNITED STATES 01'" AMER1CA
STEERING GEAR SPECIFICATIONS

i
I I
STEERING GEAR MODELS Steering Gears: Make . . . . . . . . . . . . . .
TA-12
T-14
TA-14
TA-54
TA-61
T-66
TA-66
[TJ
TA-70
Ross
Ross 17:15:17 .9980
Ross 20: 18:20 1.1230
Ross
Ross
Ross
Ross
Ross
o -1 o
-1
C (') r;
(f)
3::
:::a :::a
Ratio . . . . . . . . . . . . . . 15.4:13.5:15.4 Lever Shaft Diameter . . . .9360
20:18:20 22: 18:22

19:17:19 1.1230 1.248 1.3730
23.4: 19.5: 23.4 23.4: 19.5:23.4 1.3730 1.4975
Pitman Travel: Available

0
120
116 0
116 0
116 0
112 0
104 0
112 0
106 0
:::a
[TJ
<
(')
Steering Post Diameter . . . . . Steering Jacket Diameter . . . .
7/8" 1-1/2"
7 /8" 1-1/2"
7 /8" 1-1/2"
7/8" 1-1/2"
[TJ
1" 1-3/4"
1" 1-3/4"
1" 1-3/4"
1" 1-3/4"
r
c
z
3::
(fl
o-l
~~
(flM
'1:!~Cl
(IQ
82 ~Cl
P>~M 0 " ro ::l ,.....

-Ul~
STEERING GEARS Section A Page I
STEERING GEARS
TA-12 I T-14 I TA14 I TA-54 I TA-61 I T66 I TA-66 I TA-70
Nut and lock washer
~ ~~,
3
'\ ~ Jacket tube 4 Upper cover
~/5 Shim.
3 :t. Screws 5" Shims \
.....t /
Cap Screws ......
Cam--~~
Id '
Adjusting'lO'
screw
9
Lock nut
... "
Lock nut
2 Arm
-"::;:::;:f":
A.22452
End cover and tuhe assembly
Fig. I - Models lA-12, l-Iq, TA-JlL
End cover and ;" tube assembly A.22479 Fig. 2-Models lA-Sq,lA-61,l-66, lA-66 , lA-70. Lever shaft
01J
Construction (See Figs. 1, 2, 3)

L-Line Trucks are equipped with (Ross) semi-reversible cam and twin-lever steering gears. The twin-lever construction is shown in Figs. I and 2. There are two types of twin-lever gears
used:
BOTTOM OF GROOVE NOTE VARIATION SHAllOWER AT A & B
1.
Twin-lever with sliding studs -- the studs are riveted in the lever so that the studs have a sliding contact with the cam (Fig.
PERMISSIBLE LASH IN POSITIONS
I).
2. Twin-lever with rolling studs -- the studs are mounted in the lever with tapered rol ler bearings so that the studs have a roll ing contact on the cam (Fig. 2).
GEAR IStuds A & BI SHOWN AT MID-POSITION OF TRAVEl c ,hows VARIOUS POSITIONS OF STUD A ON TURNS b shows VARIOUS POSITIONS OF STUD B ON TURNS IMPORTANT -ADJUST THRU THE MID-POSITION
Both studs of the twin-lever gear engage the cam for normal straight-ahead driving. As the steering action muves away from the normal driving position into the parking range, one of the studs dis engages the cam. The effective leverage of this single stud increases so rap idly, however, that in full parking the leverage is 45 percent greater than with a single-lever type steering gear. This is due largely to the fact that because of the twin levers the steer ing arm is shorter and, therefore, has a full 100 degrees of travel compared to 76 degrees in a single-lever unit. Actually, the driver has at his disposal a dual-ratio gear which auto matically changes froITl one ratio to another to suit the requirements of steering stability at high speeds, and easy wheel turn for sharp
PRINTED IN UNLTED STATES OF AMERICA
A23440
Fig. 3
turns in parking. A valuable safety factor is a lessening of the tendency to over-steer on c;urves and when passing other vehicles at high speed (See Fig. 3).
Adjustments
NOTE: The basic design of the steering gears used in these trucks is siITlilar and the method of servicing applies generally to all units used. For illustrative purposes, assem blies of the more COITlmon type are used.
STEERING GEARS Section A Page 2

Filler plug (11---."11
Except for position of the lever shaft in the housing, the steering gear details are similar and are serviced in the same manner. When making adjustments, free the steer ing gear of "all load, preferably by disconnect ing the drag link from the steering arm, and loosen instrument panel bracket clamp on steering gear jacket tube.
If the ball thrust bearings on the cam must be adjusted, make adjustment(l) before making side adjustment to lever shaft studs in cam groove (2).
1. ADJUSTMENT OF BALL THRUST BEAR

INGS ON CAM. (a) Before making this adjustment loosen the housing side cover adjusting screw (9, 10) to free the studs in the cam groove (Fig. 4). (b) Adjustment should be made so there is a very slight drag but not so much that steering wheel cannot be turned from extreme to extreme by lightly gripping rim with thumb and fore finger. (c) Unscrew the four screws (3) and raise the housing upper cover (4) to permit removal of shims (5). (Shims are of .002", .003" and .010" thickness). (Fig. 5). (d) Clip and remove a thin shim or more as required, and draw cover down tight against shims. (e) Test as outlined in paragraph (b) and if necessary remove or replace shims until adjustment is correct.
(9) \, Lock nut',\
'--".'f
....
A-22530
Fig. ~ Illustrates screw and locknut
location
of
adjusting
2. ADJUST LEVER SHAFT STUDS IN CAM

GROOVE FOR BACKLASH. (a) Backlash at this point shows up as end play of lever shaft, also as backlash at steering wheel and at ball on steer ing arm. (b) The groove is purposely cut deeper in ends of cam than in mid-position. This produces a high range through mid position and makes grooves narrower through this range. This permits take-up of backlash in mid-position, after normal wear of groove, without causing a bind in ends (Fig. 3). (c) Adjustto this mid-position high range. Do not adjust in end positions. Play in end position is not objectionable. (d) Tighten side cover adjusting screw (10) until a very light drag is felt through the mid-position high range when turning steering wheel slowly
Fig. 5 - Showing location of shims under upper housing cover used to adjust end-play on cam. (Shims are of .002", .003", and .010 thickness)
from extreme to (Fig. 4). extreme position
(e) IMPORTANT: Steering gear must not bind any position. Only a very slight drag should be felt. A closer adjust ment will not correct steering loose ness caused by wear in other steering gear members, but will damage parts and impair operation.
(f) When
proper adjustment has been made, tighten lock nut (9) and then give gear a final test.
(g) Make sure steering gear arrn is tight on splined lever shaft and that lock washer and nut are tight also.
LL1NE MOTOR TRUCK SERVICE MANUAL

3. STEERING COLUMN ALIGNMENT. (a) After adjustments have been made and lock screw tightened, turn steering wheel to see if any stiffness exists. If so, steering gear has been adjusted too tight or steering column is out of alignment. Misalignment of the column places a bend in the column, conse quently, the wheel tube must undergo reverse bending stresses during each revolution. This is a serious condition and mustbe avoided. THE STEERING COLUMN MUST NOT BE SPRUNG IN ANY DIRECTION. 4. STEERING GEAR FRONT WHEELS, CONNECTION WITH
STEERING GEARS Section A Page 3
(a) The steering gear should be connected to the front wheels so as to obtain as nearly as possible the specified turn ing radius on both left and right turns. This is accomplished by turning the steering wheel as far to the right as possible, then rotate the wheel in the opposite direction as far as possible and note the total number of turns, Turn the wheel back just onE?-half of this total movement, thus placing the gear in the mid'-position. With the front wheels in position for straight ahead driving, it should then be pos sible to connect the drag link to the ball on the end of the steering gear arm without moving the gear to any appreciable extent, If this cannot be done, remove the arm from the steer ing gear, using a suitable puller, and place it on the splined shaft in the proper position. Otherwise it will not permit the front wheels to swing equal ly to the left and right, Check steering knuckle s top on front axle to make sure that there is proper clearance for the tire when turning at maximum angle. Axle stops should also be set out sufficiently to prevent steering gear from lIbottoming", that is, to stop the gear short of its absolute limit of travel. If the gear is permitted to bottom, damage to internal parts will occur. Check to see if axle stops are set to do this on both left and right turns. See that steering gear housing is filled with lubricant as recom mended in "Lubrication Section". 5. TO REMOVE STEERING WHEEL (Figs. 6 and 7),
A21734
Fig,
6, Models TA-12, T-14, TA-14, TA-54
5 4
3
IO
A21736
Fig. 7, Models TA-61, T-66, TA-66, TA-70
LEGEND for Figs. 6 and 7. 1, Z. 3. 4. 5. 6, Horn cable assembly 7. Steering wheel Steering tube 8. Horn button Jacket tube 9. Horn contact cap Bearing assembly 10. Steering wheel nut Spring seat 11. Base plate assembly Spring 12. Horn button spring
(a) Disconnect horn wire at bottom of

steering gear.
(b) Remove horn button (8) by pressing down and turning to right or left with
PRINTED,N UNrTED STATES
or
AMERICA
STEERING GEAR Section A Page 4

(e) Connect horn wire at bottOIn of steer ing gear. 7. DISASSEMBLING STEERING GEAR. (a) ReInove horn button. cable and steer ing wheel. (b) ReInove housing side gear cover and pull out lever shaft (Fig. 8). (c) Loosen claInp collar and reInove jacket tube and housing upper cover (Fig. 9). (d) ReInove caIn and tube asseInbly. COIn plete with bearings. froIn the housing (Fig. 10). (e) ReInove lever shaft oil seal and clean the counterbore in the gear housing. S. REASSEMBLING STEERING GEAR. (a) Install new lever shaft oil seal (Fig.
palIn of hand or vacuum cup, holding steering wheel stationary. (c) ReInove contact cap and spring. (d) ReInove the three screws holding the horn button retainer base plate (11) and reInove this plate and horn wire. (e) ReInove steering wheel nut (10) and take off steering wheel using a suitable puller. 6. TO INSTALL STEERING WHEEL. (a) Place in correct position on shaft. Wheel should be installed so that spokes are in shape of a lIy" when seated in driver's s,eat and with front wheels straight ahead. This will per Initdriver to read instruments through the top of steering wheel. (b) Install steering wheel nut (10) and tighten securely. (c) Ins ert horn wire and thread through hole in cover plate at bottoIn of steer ing gear housing. Attach horn button retainer base plate (11) with three screws. (d) Install contact plates, spring and horn button. Horn button should be pressed down and turned until it locks in the rubber retainers on retainer base plate, using vacuum cups or palIn of hand.
ll).
Pos i tion oil seal in hous ing with side staInped "FluidSide" towardbottoIn of counterbore. Using a haInIner, tap lightly on the end of a socket wrench or adapter (cold rolled stock) having a slightly sInaller outside diaIneter than the oil seal. It is iInportant that the seal bottoIns in the counterbore of housing. (b) Place caIn and tube asseInbly with bearings in the housing (Fig. 10).
Collar clamp
Fig. 8 - Removal of housing revealing lever shaft
side
gear
cover
Fig. 9 - Removal of jacket tube and upper hous ing cover assembly

Drag Link (Figs. 12, 13, 14)
Front adjusting plug
Housing
Ball seat
Front plug
Fig. 12
Rear adjusting plug

A-22B91
Fig. 13 Fig. 10 - Removing bearings cam and tube assembly with
Steering gear housing
This type of drag link requires very little care other than periodical lubrication and occa sional inspection to make sure that it is prop erlyadjusted. (Figs. 12 and 13). Adjustment is made by removing cotter pin and turning adjusting plug in the desired direction. To adjust for wear, turn adjusting plug in until it is tight, then back off to first cotter pin hole. Insert a 1l.:Y:' cotter pin of the correct size and bend ends over securely. Drag link should not be adjus ted too tight, other wise steering will be affected. The spring is merely to accommodate wear and is not intended to act as a cushion against shock. Fig. 14 shows details of steering gear, relay link and drag link used on L-190 series trucks and up.
A-22470
Fig. II Location shaft oi I seal
and installation of lever
(c) Assemble housing upper cover with shims and make proper bearing ad justments. (d) Install lever shaft in housing and assembly housing side cover, first loosening the adjusting screw(Fig. 8). Draw side cover screws tight. (e) Adjust lever shaft stud in cam groove for backlash and lock adjustment with lock nut. (f) Assemble jacket tube with clamp col lar and tighten clamp. (g) Install steering wheel, horn cable and button.
Fig. PI Steering gear linkage to front axle for models L-190 series and up
Steering Jacket Tube Bearing

A ball-type steering jacket bearing is used, improving steering gear performance and ease of handling. Fig. 15 illustrates this construc tion.
Fig. 15 - Showing location of jacket tUbebearing Special se rvice tools (SE -1164) are avail able for this bearing, and are to be used for installation of a new bearing (see Fig. 16).
o
Arbor 5E-1164-1
Adapter 5E-1164-2
Bearing Jacket tube
A22890
Fig. 16 - Installation tube bearing
of steering gear jacket
TRANSMISSION Index 1
TRANSMISSION GROUP
INDEX
SPECIFICATIONS
SPECIFICATIONS SPECIFICATIONS (TRANSMISSIONS)............... .............. .... (AUXILIARY TRANSMISSIONS) . . . . . . . . . . . . . . . . . . . . . . . 1 2
GENERAL INFORMATION
Driving downhill . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Overdrive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Overload . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Shifting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION HA" (HDS)

Models L-lIO, L-120 Disassembling and reassembling. . . . . . . . . . . . . . . . . . . . . . . . . . . . Gear shift diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . l, 2, 3 2
SECTION "B" {T-87-D}

Models L-llO, L-l20, LM-l20, L-l30, LM-ISO Disassembling and reassembling. . . . . . . . . . . . . . . . . . . . . . . . . . Gear shift diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . 1, 2, 3 2
SECTION "C" (H-41-B)

Models L-130, L-lSO, L-lS3 Disassembling and reassembling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Gear shift diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1, 2, 3 2
SECTION "D" (T-98)

Models L-ISO, L-lS3, L-160, L-163, L-I64, L-16S. LC-160, L-17.0, L-173, L-174, L-175, LF-170 Disassembling and reassembling . . . . . . . . . . . . . . . . . . . . . Gear shift ................................... Transmission removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1, 2, 3 2 3
SECTION "E" (F-51 AND F-51-C)

Models L-170, L-I73, L-I74, L-175, LF-170, L-180, L-183, L-184, L-185, LC-180 Disassembling and reasseITlbling . . . . . . . . . . . . . . . . . . Gear shift ........................
I, 2, 3 2
TRANSMISSION Index Page 2
SECTION "F" (F-52 AND F-52-C)

Models L-190, L-l93, L-194, L-195, LF-190, LC-190, L-200, L-204, LC-200 Disassembling and reassembling . . . . . . . . . . . . . . . . . . . . . I, 2, 3 Gear shift diagram. . . . . . . . . . . . . . . . . . . . . . . . . 2
SECTION "G" (F-54 AND F-54-B)

Models L-200, L-204, L-205, LC-200, L-210, LF-2l0 Disassembling and reassembli.ng . . . . . . . . . . . 1, 2, 3 Gear shift diagram . . . . . . . . . . . . . . . . . . 2
SECTION "H"
(FULLER AUXILIARY TRANSMISSION)
Model 2-A-45
Disassembling . . . . . . . . . . . . . . . . . . . . . . . . 1,2,3 Reassembling . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3, 4
SECTION "I"
(BROWN-liPE AUXILIARY TRANSMISSION)
Model 5531
Disassembling Reassembling
1, 2
3, 4
SECTION "J"
(BROWN-liPE AUXILIARY TRANSMISSIONS)
Models 6231 and 6231-A
Disassembling Reas sembling

.. .. '" '" .. '" '" .. .. .. .. .. .. .; .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. I> .. .. .. .. .. ..
1, 2, 3 3, 4
SECTION "K"
(BROWN-liPE AUXILIARY TRANSMISSIONS)
Models 8031-C and 8031-G
Disas sembling
Reasserrlbling ..................................................................................... .
TRANSMISSION MODELS (1 H)
HDS
T-87-D
H-41-B
T-98
F-51
F-51-C
F-52
F-52-C
F-54
F-54-B
Transmission (make)
IH
Warner
Warner
Warner
Fuller 5-A-330 O.D. in 5th Yes 1
Fuller 5-A-33 Direct in 5th No 1
r: r
Z
[T1
Manufacturer's model Type . . . . . . .
----Synchromesh No 1
AS-4-T-87D AS-74-T-9 ASA T-98 Synchromesh No 1 Direct in 4th No

I
Synchromesh No 1
Overdrive .
o --l o :::a
--l
3:
Number of forward speeds Reductions: First (low) .

Second
:::a
()
3.058-1 1.481-1 1.000-1
3.714-1 1.871-1 1.000-1
6.40-1 3.09-1 1.69-1 1.00-1
6.398-1 3.092-1 1.686-1 1.00-1
6.36-1 3.725-1 1.92-1 1.000-1 .823-1
7.35-1 4.30-1 2.52-1 1.42-1 1.000-1
6.98-1 3.57-1 1.89-1 1.00-1 .825-1
8.03-1 4.61-1 2.46-1 1.41-1 1.000-1
7.07-1 3.50-1 1.72-1 1.00-1 .776-1
8.08-1 4.67-1 2.62-1 1.38-1 1.00-1

8.12-1 4.74-1 2 24
A
(f)
:::a
[T1
Third .
Fourth . . .
()
<
---------
------------4.588-1 None
[T1
Fifth
.................
--------
7.82-1 1 5
-----
z c
r
3:
High reverse Low revers e
----3.707-1 None 3
----7.820-1 1 8
----6.39-1 2 12
----7.20-1 2 12
----6.95-1 2 19
----8.00-1 2 19
----7.11-1 2 24
'U M>-j 0::0

~z
Number of p. T. O. oppni'1g Lubricant capacity (pints)
en
1-<>
>E::':
oen
>-jen ...... en 0 ..... ZO
~enZ
'\jCllI-j $ll '\j::o

aQ
(1)()Z N ...... CIl
M:>
AUXILIARY TRANSMISSION SPECIFICATIONS
:>g; I-j ......

8031-C
CIl
:::lg: () ......
Oz Z
HO
MODEL
2-A-45
5531
6231
6231-A
8031-G
Make
Fuller
Brown-Lipe
Brown-Lipe
Brown-Lipe
Brown-Lipe
Brown- Lipe
r
[T1
Number of speeds
3:
Number of bearings
....
0
Type of bearings
6-Ball, I-Roller
2-Ball, 4-Roller
I-Ball, 6-Roller
I-Ball, 6-Roller
3-Ball, 3-Roller
3-Ball, 3-Roller
::0 -l ::0 C
(')
-l
A
t/)
Ratios; Di r ec t '" .
II;J
[T1
::0
0 '"
'ill '" .....
1.00 to 1 1.30 - I
1.00 - 1 2.00 - 1 .72 - 1
1.00 - I 2.14 - 1 .69 - 1
1.00 - 1 1.24 - 1 .86 - 1
1.00 - 1 2.59 - 1 .75 - 1
1.00 - 1 1.29 - 1 .84 - 1
(') [T1
<
Underdrive Overdrive
...... 0 GO
--------
Lubricant capacity: Summer (pints) Winte r (pints) 10 10 6 6 8 8 8 8 12 12 12 12
z c r
3:
TRANSMISSION General Page I
TRANSMISSIONS
Driving Downhill
A safety rule to follow by all good drivers is to use the same or next lower transmission gear when going downhill as would be used in climbing the same hill. If necessary, the vehicle speed can then be easily controlled to the maximum road speeds for that particular gear by "snubbing down" with the brakes. This practice will not only prevent damage to the engine, but will also effect a saving on the brakes. CAUTION: Do not coast down hill, even for a very short distance, with the clutch disengaged. If the clutch is engaged while the truck is coasting, the sudden acceleration of the engine's speed will result in a shock to the gears, an excessive strain and ultimate failure of the driving parts. thirty-three miles per hour since that is the maximum available road speed for this truck in third gear. Gear changes from a higher to lower gear speeds should be made as follows: 1. Ease off on accelerator and disengage clutch. 2. Move gear shift lever to neutral position and engage clutch. At same time, accelerate engine to governed speed. 3. Disengage clutch, ease off on accelerator, and move gear shift lever to next lower transmission gear position. 4. Engage clutch and depress accelerator sufficiently to pick up load. The above procedure, known as "double clutching," is necessary to bring about an equal ization or synchronization of engine speed and transmission gear speed, and thereby prevent clashing of gears.
Overdrive
Some transmis sions have an over-drive spe ed. This gearing is for maintaining in creased road speed with reduced engine speed. Overdrive should be used only when conditions are favorable to high road speeds. Overdrive should never be used at low road speeds or for lugging. Usually, for overland hauling, the minimum road speed for overdrive is 30 m.p.h.
Overload
The transmis sions installed in International trucks are engineered to the rated capacity of the trucks. An ample safety factor well above normal requirements has been provided, but neither the transmission nor any other part of the truck will give maximum performance and long wear if continued to load it beyond its rated capacity.
When the truck is equipped with a governor the maximum engine speed is controlled. If, however, it is desired to shift at lower road speeds than those shown, the shifts should be made at correspondingly lower engine speeds. Since the governor does not operate at the lower engine speeds, determination of the proper lower engine speed at which to shift is a matter of judgment that comes with practice.
Shifting
Probably one of the most distinguishing characteristics of a good driver is his ability to shift gears from a high to a lower trans mis sion speed. A knowledge of the maximum obtainable road speeds in the various gears is helpful in deter mining the maximum road speed at which a shift bom a high to a lower gear can be made. For example, in shifting fourth speed to third speed. the maximum road speed at which this change can be made is at approximately
PRINTED IN UNITED STAT~$
When the operator becomes accustomed to the sound of the engine at various engine speeds and has become experienced at "double-clutching" he should be able to shift from a high to a lower gear very rapidly--and without clashing the gears. CAUTION: When shifting, avoid injury to the gear teeth by making it a practice to shift gears with as little clashing as possible.
Starting
When starting a new unit or one which has been exposed to cold weather, allow sufficient time for the lubricant to circulate and coat all contacting surfaces. Do not stay in anyone gear for any length of time. The metal-to-metal contact between some of the working parts, due to insufficient lubrication, will result in damage which may not appear immediately but will eventually develop into serious trouble.
or
AMERICA
TRANSMISSION Section A Page 1
TRANSMISSION (HDS)
49 48
47 46 39 38 37 36 35 34 33
A-21744
Fi g. I - (H DS)
No.
Description
NO'
I
i I
Description
Main drive gear bearing retainer. Retainer gasket. Main drive gear. Mainshaft pilot bearing spacer. Sliding clutch synchronizer ring. Mainshaft clutch sleeve. Clutch poppet ball. Selector lever assembly. Clutch poppet spring. Second speed gear lock ring. Second speed gear. Transmission cover. Shift lever assembly. Shift lever setscrew. Mainshaft adapter. Second speed gear,lock ring. Mainshaft.
Mainshaft sliding gear (low and
reverse) . 19" Transmission cover gasket. 20. Rear bearing retainer gasket. 21. Mainshaft rear bearing. 22 . Speedometer drive gear. 23. I Mainshaft rear bearing retainer. 24. Oil seal.
PRINTEO IN UNITE!:) STATES OF AMtR1CA
1. 2. 3. 4. 5. 6. 7. S. 9. 10. 11. 12. 13. 14. 15. 16. 17. IS.
25. Flange. 26. Lockwasher. 27. Nut. 28. Oil slinger. 29. Speedometer gear spacer. 30. C ounte r shaft. 31. Countershaft thrust washer (bronze). 32. Countershaft thrust washer {steel}. 33. Countershaft roller bearing. 34. Transmission case. 35. Countershaft gear cluster. 36. Countershaft bearing spacer. 37. Drain plug.
3S. Countershaft roller bearing.
39. Countershaft thrust washer. 40. Second speed gear thrust washer. 41. Clutch sleeve (second and high). 42. Clutch hub (second and high).
43 . Main drive gear ball bearing.
44. Bearing lock ring. 45. Mainshaft pilot bearing. 46. i Idler shaft snap ring. 47. Reverse idler shaft. 4S. Reverse idler gear. 49. Reverse idler gear bushing.

Use shift bar to tap out bar thiInbles (dust plugs). With the reInoval of shift bar, the shift fork is lifted out through top of case. (c) ReInove interlock plunger retainer capscrew to release interlock plunger froIn case. CAUTION: In reasseInbling trans Inission, be sure to insert interlock plunger, poppet springs and balls.
TRANSMISSION (MODEL HDS)

The Model HDS transInission is of synchro Inesh type with reInote control having three speeds forward and one reverse. Fig. 2 illus trates the shift diagraIn.
~
I
I
I
"''1
(d) ReInove low and reverse shift bar and fork, in the saIne Inanner as described in paragraph (b).
Fig. 2 - Shifting Diagram (HDS)

DISASSEMBLING AND REASSEMBLING
With a few Ininor exceptions, the asseInbly is siInply the reverse of disasseInbling. Therefore the following disasseInbly instructions will also serve as reference for asseInbling. Fig. 1 illustrates construction details of this transInission and figure nUInbers in parentheses throughout this section will refer to this illu stration.
Fig. 3 - Sectional View of Shifting Bars,Poppet Springs and Balls and Shifting Forks.
5, ReInoving Inain drive gear asseInbly: (a) Lock transInission and reInove COIn panion flange (25). ReInove caps crews three in nUInber - froIn Inainshaft rear bearing retainer (23). Lift off retainer and gasket (20) revealing oil deflector (28), speedoIneter drive gear (22) and spacer (29). (b) Drive out countershait (30) toward rear of case perInitting countershaft gear cluster (35) to drop down in case, allowing clearance for reInoval of Inain drive gear.
1. Clean outside of transInission, particularly around the control and bearing covers (1, 12,23).
2. Shift selector lever (8) and shift lever (13) to neutral position. ReInove cotter pin and breather cap froIn hold-down bolt. Re Inove four capscrews and lockwashers frOIn control cover (12) and lift off control cover asseInbly. 3. To disasseInble the control cover asseInbly:
(a) ReInove outer selector lever setscrew releasing both outer and inner levers (8). (b) ReInove shift lever setscrew (14) and this will release the shaft, spring and shift lever (13).
4. DisasseInbling shift forks and shafts: (a) ReInove poppet ball and spring retainer plugs releasing balls and springs. (b) ReInove setscrews frOIn shift forks and slide shift bar toward rear of case.
(c)
ReInove caps crews - four in nUInber froIn the Ina in drive gear bearing re tainer (1). ReInove retainer (1) re vealing Inain bearing (43) and retaining ring (44). NOTE: When reasseInbling, see that oil drain in r<::!tainer (1) is located at bottoIn.
(d) Main drive gear (3) and bearing (43) can now be reInoved froIn case (34) by driv ing toward front of case. CAUTION: Exercise care not to daInage bearing (43) when driving froIn case.

6. RerrlOval of mainshaft assembly: (a) With companion flange (25) and main shaft bearing retainer (23) removed, slip off oil deflector (28) speedometer drive gear (22) and spacer (29) from mainshaft assembly. (b) Remove mainshaft rear bearing (21). CA UTION: Exercise care in driving off bearing to prevent its being damaged. (c) Mainshaft assembly can then be lifted out through top of case. NOTE: Main drive gear assembly (3) must be removed first as outlined in paragraph 5.
(b) To reassemble, insert clutch partially in sleeve and install springs and balls. Then insert cotter pins (1/8 x 2 ") hav ing the ends spread slightly as shown in Fig. 4. The cotter pins, when between the splines, force the balls into the clutch and after clutch is pressed into sleeve, cotter pins can be removed.
7. Removal of countershaft cluster gear: (a) As countershaft (30) has already been removed for disassembly of main drive gear (3), the counter shaft gear cluster (35) is merely lifted out through top of case. Be sure to remove the bronze washer (39) at front and bronze washer (31) and steel thrust washer (32) at rear in bottom of case.
Fi g. 4
(b) Countershaft bearings (38) and spacer (36) can also be removed from gear cluster.
8. Removal of reverse idler gear and shaft: (a) Reverse idler shaft (47) can now be removed by dr~ving shaft toward rear of case and this will permit lifting idler gear (48) out through top of case. NOTE: When reassembling, be sure to position shaft so that recess will take rear bearing retainer properly.
9. Disassemblyofmainshaft clutch assembly: (a) Mainshaft clutch and sleeve are held together by poppet springs (9) and balls (7). Mainshaft clutch can be removed from sleeve by supporting outer diameter of sleeve and pressing on clutch. Use care when disassembling as poppet balls are under spring tension and may fly out when sleeve is removed. It is suggested that a cloth be wrapped around the assembly to guard against this. A special tool, SE-920, is available which if used, will facilitate disassembly and reassembly. If you do not have this tool on hand, follow instructions out lined in paragraph (b).
"~INTD
IN UNJTED $TATES OF' AMERICA
TRANSMISSION Section B Page 1
TRANSMISSION {T-87-D}
Fig. I - (T-87-D)
No. Description Main drive gear. Bearing snap rings. Main drive gear bearing retainer. Synchronizer blocking ring. Transmission cover. Expansion plug. Shifting plate. Clutch sleeve (second and direct). Interlock plunger. Poppet ball and spring. Shift fork (second and third). Shift lever. Shifting shaft. Shift fork (low andl"everse). Mainshaft second speed gear. Shift rail. Mainshaft low and reverse, gear. Expansion plug. Transmission cover gasket. Oil retainer washer. Mainshaft rear bearing retainer. Mainshaft 'ing snap ring.
PRINTEO IN U!'4fTD STATES OF AMRICA
No. 23. 24. 25. 26. 27. 2B. 29. 30. 31. 32. 33. 34. 35. 36. 37. 3B. 39. 40. 41. 42. 43. 44.
Description Mainshaft rear bearing. Oil seal. Mainshaft. Mainshaft flange nut. Speedometer drive gear. Counter shaft thrust washer (inner). Countershaft thrust washer (outer). Counter shaft. Lock plate. Lock plate capscrew. Reverse idler shaft. Reverse idler gear bushing. Reverse idler gear. Countershaft gear cluster. Countershaft thrust washer (front). Countershaft roller bearing. Transmission case. Countershaft bearing spacer. Oil retainer washer. Main drive gear bearing. Clutch hub (second and direct). Mainshaft pilot bearing.
1. 2. 3. 4. 5. 6. 7.
B.
9. 10. 11. 12. 13. 14. 15. 16. 17.
lB.
19. 20. 21. 22.

(c) Remove snap rings from shifting shaft (13) located on each side of shift lever (12) thus releasing shaft assembly (13), spring, shift lever (12) and key. (d) Interlock plunger (9) may be removed by pulling 3/8" tapered plug located on left side transmission cover (5) directly below poppet spring and ball. NOTE: When reassembling the top cover assembly (5) to case, make sure that shift forks (11, 14) are not sprung and engaged properly with sliding gears. 4. To disassemble the mainshaft assembly, (a) Lock transmission and remove com panion flange nut (26). Remove cap screws - four in number - holding main drive gear bearing retainer (3) to case (39) and five capscrews hold ing mainshaft assembly rear bearing retainer (21). (b) Lift off main drive gear retainer (3) revealing snap rings (2) and bearing (42). Remove mains haft rear retainer (21) re:vealing speedometer drive gear (27) snap ring (22) and bearing (23). NOTE: When reassembling the front bearing re.tainer (3) see that oil drain in retainer is located at bottom. (c) With the mains haft rear bearing re tainer (21) removed, slip speedometer drive gear (27) from mainshaft (25). Remove mainshaft rear bearing (23) and oil retainer washer (20). CAUTION: Exercise care in driving off bearing to prevent damage. (d) Pull main drive gear (1) and bearing (42) out through front of case until drive gear contacts countershaft gear. Slide rnainshaft assembly through rear bore of case as far as necessary to clear main drive gear (1) and lift out through top of case. CAUTION: Be sure to catch pilot needle bearings (14) - sixteen in number - when removing mainshaft as sembly. A helpful suggestion in re assembling pilot needle bearing (44), use a rubber band to hold the sixteen needle bearings in place until the as sembly is started in the main drive gear and then the rubber band is removed be fore completing the assembly. (e) To disassemble rnainshaft assembly, re more retainer snap ring and use sliding gear (17) to tap synchronizer assembly and bushed gear (15) from rnainshaft.
TRANSMISSIONS (MODEL T-87-D)

The Model T-87-D transmission is of syn chro-mesh type, with remote controls, having three speeds forward and one reverse. Fig. 2 illustrates the shift diagram.
~
I
I
I
"'"
Fig. 2 - Shifting Diagram (T-87-D)
DISASSEMB LING AND REASSEMB LING
The assembly is simply the reverse of dis assembling with the exception of a few minor details. Therefore the following disassembly instructions will also serve as reference for assembling. Figure numbers in parantheses throughout this section will refer to Fi . 1 which illustrates construction details 0 this transmission.
1. Clean outside of transmission especially

around the control and bearing covers (3,' 5, 21). 2. Shift selector lever (12) into neutral position. Remove capscrews and lockwashers holding cover assembly (5) to case (39) and lift off the cover assembly.
3. To disassemble the control cover assembly: (a) Clip lockwire and remove locks crew from low and reverse speed shift fork (14). Tap shift rail (16) toward rear of cover driving out expansion plug (18). Pull out shift rail (16) releasing poppet spring and ball (10) and shift fork (14). CAUTION: Do not lose poppet springs and balls. (b) To remove second and third speed shift fork (11), rail, expansion plug, poppet spring and balls (1 0), follow the same procedure as in step (a).

5. To disassemble main drive gear: (a) Remove snap ring (2) holding bearing (42) on main drive gear (1). Push the drive gear and bearing assembly back into case until outside snap ring seats snuggly against case. USLrlg a soft ham mer, tap the mains haft gently toward inside of case until bearing is freed and the mainshaft can then be lifted out through top of case. CAUTION: Do not damage bearing during this operation. 6. To disassemble countershaft assembly: (a) Remove capscrew (32) and lock plate (31) releasing countershaft (30) and reverse idler shaft (33). Drive counter shaft (30) out through rear of case using a brass drift. With the countershaft removed, the gear cluster (36) can be lifted out through top of case. Be sure to pick up the bronze thrust washer (37) at front and bronze washer (28) and steel washer (29) at rear in bottom of case. (b) Countershaft bearings (38) and spacer (40) can also be removed from gear cluster.
moved by driving out through rear of case. May also be removed by placing a pinch bar in lock plate slot and pulling out shaft. With the idler shaft (33) removed, the idler gear (35) can be lifted out of case. NOTE: When re assembling, be sure to position properly slots in countershaft (30) and idler shaft (33) to take lock plate (31). 8. To disassemble mains haft clutch assembly: (a) The mainshaft clutch hub and sleeve are held together by two retaining springs located on each side of clutch hub. The clutch sleeve (8) can be re moved from clutch hub (43) by removing the retaining springs and supporting the outside diameter of sleeve (8) and pressing on hub (43). Use care when dis assembling not to lose the three shifting plates (7). The blocker rings (4) are supported by the main drive gear hub and second speed gear hub and are dis ass e m bled with the r em oval of the mainshaft assembly. CAUTION: In reassembling the clutch, be sure to place end of each retaining spring in the same shifting plate with the loose ends located in same position on both sides to equalize the tension on all three shilting plates (7). Also index etched marking on hub and sleeve.
7. Removal of reverse idler gear and shaft: (a) Reverse idler shaft (33) can be re
O~
AMERICA
TRANSMISSION Section C Page 1
TRANSMISSION (H-41-B)
33 32
~--31
Fig. I - (H-ltl- B)
No. Description Shift lever. Retainer. Retainer washer. Spring. Fulcrum ball. Pin. Contrpl cover. Poppet spring. Poppet balL Interlock pin. Shifter shaft. Shift fork prd and direct}. Shift fork 1st and 2nd}. M. drive gear brg. retainer. No. 15. 16. 17. 18. 19. 20. Description Main drive gear. Main drive gear. Main drive gear bearing. Mainshaft gear (3rd and direct). Countershaft thrust washer. Countershaft gear cluster. Drain plug. Bearing spacer. Countershaft bearing. Reverse idle gear. C ounte r shaft. r;7o. Description
1. 2, 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14.
Zl.
22. 23. 24. 25.
26. Mainshaft gear (low and second). 27. Mainshaft rear bearing. 28. Spacer. 29. Speedometer drive gear. 30. Mainshaft. 3l. Washer. 32. Cotter pin. 33. Nut. 34. Grease seal. 35. Rear bearing retainer. 36. Grease slinger. 37. Expansion plug. 38. Shifter fork lock screw.
P~INTED IN UNITED STATES OF AME~LCA
TRANSMISSION Section C Page Z
LLlNE MOTOR TRUCK SERVICE MANUAL

3. To disassemble the control cover assembly:
TRANSMISSIONS (MODEL H-41B)

The Model H-41-B transmission is of sliding gear type, having four speeds forward and one reverse. Fig. Z illustrates the shift diagram.
(a) Remove control lever retainer (Z) from

top of cover (7). Lift out control lever (1), retainer (Z). washer (3). and spring (4) and fulcrum ball (5). Fulcrum ball (5) can be removed from control lever (1) by driving out pin (6) with a suitable punch.
cp
I ~
q:>
I
(b) Clip lockwire from first and second
~- -'N'- -1- -
- -
-,,
cD
cD
speed shift fork (38) and remove lock screw (38). Drive shift rail (11) to ward rear of cover driving out expan sion plug (37). With the expansion plug removed, pull shift rail (11) out and lift shift fork (13) out of cover. CAUTION: Do not lose poppet spring (8) and ball (9).
(c) Continue disassembly operation re

moving third and direct shift fork (lZ), reverse shift block, stop pin, spring, rails, poppet balls and springs and inter lock pins and stops. CAUTION: In reassembling the control cover, care should be exercised to see that all parts are replaced in their correct positions and none of the small inter locking parts are lost or omitted.
Fig. 2- Shifting Diagram (H-Itl-B)
DISASSEMB LING AND REASSEMB LING

With a few minor exceptions, the assembling is simply the reverse of disassembling. There fore the following disassembly instructions will also serve as reference for assembling. Fig. Z illustratys construction details of this transmission and figure numbers in paren theses throughout this section will refer to this illustr ation.
4. To remove mains haft assembly: (a) Lock transmission by engaging two speeds and remove flange nut (3Z). (b) Remove five capscrews holding main shaft rear bearing retainer (35) to case. Lift bearing retainer off rnainshaft revealing gasket, speedometer drive gear (Z9), spacer (Z8), and mainshaft rear bearing (Z7). (c) Hold mainshaft sliding gears (18, Z6) in position. Mainshaft (30) and bearing (Z7) can now be removed through rear of case, If necessary, use a brass drift against washer (3l) and nut (32). (d) Lift out mainshaft third and direct gear (18) and low and second gear (26) through top of case.
1. Clean the outside of the transmission, particularly around the control and bearing covers (7, 14, 35).
Z. Place shift lever (1) in neutral position. Remove the six holding caps crews and lift off the control assembly (7). CAUTION: Do not force the control cover off the transmission. Forcing may spring the yokes of alignment and caus e partial engagement or gear interference. If bind ing occurs, a slight manipulation will free it.

5, To disassemble the mainshait: (a) Remove nut (32), companion flange, then remove rear bearing retainer (35), speedometer drive gear (29), spacer (28), and bearing (27).
TRANSMISSION Section C Page 3
(b) Remove cotter pin from reverse idler gear shifter fork shaft. Drive shaft toward rear of case with a brass drift and remove idler shifter fork.
6. Remove main drive gear: (a) Remove four capscrews holding main drive gear bearing retainer (14) to case. (b) Remove retainer (14) revealing gasket and bearing (17). NOTE: When re assembling, be sure to locate oil drain at bottom. (c) Main drive gear (15) and bearing (17) can now be removed from front of case. If necessary, use babbit or rawhide hammer to tap main drive gear (15). 7. Removing the countershaft assembly: (a) Remove countershaft and reverse idler shaft lock screw and plate. Drive out countershaft (25) toward rear of case, using a brass drift.
(c) Lift countershaft gear cluster (20) with bearings (23) and spacer (22), through top opening of case. Tilt gear cluster slightly through rear bore in case to facilitate removal.
(d) Remove roller bearings (23) and spacer (22) from cluster (20). Be sure to pick up countershaft thrust washers, one each end, from bottom of case. 8. Removing the reverse idler gear and shaft assembly: (a) Insert screwdriver or pinch bar in'lock plate groove and pry out shaft. Re verse idler gear can then be lifted out through top of case. NOTE: When reassembling, be sure to position slot in shaft properly to take lock plate. 9. When reassembling the top cover assembly, make sure that the'shifter forks are not sprung, and engaged properly with sliding gears.
PRINTO IN UNITED STATI[S OF AMERICA
TRANSMISSION Section D Page I
TRANSMISSION (T-98)
Fig. I - (T-98)
No. Description No. Description No. 40. 41. 42. 43. 44. 45. 46. 47. 48. 49. 50. 51, 52. 53. 54. 55. 56. Description Lock plate.
Lock plate capscrew.
Reverse idler shaft. Reverse idler gear. Transmission case. Drain plug. Counter shaft bearing spacer. P. T .0. opening. Countershaft gear cluster. 2nd speed gear bearing spacer. 2nd speed gear roller bearing. Countershaft thrust washer, front. Countershaft roller bearing. 2nd speed gear thrust washer. Snap ring. Clutch hub, 3rd and direct. ~ainshaft pilot bearing.
l. ~ain drive gear bearing retainer. 2. Snap ring. 3. ~ain drive gear bearing. 4. Snap ring. 5. ~ain drive gear. 6. Synchronizer blocking ring. 7. Shifting plate. 8. Expansion plug. 9. Sleeve (3rd and dir~ct). 10. Shift rail. 11. Transmission cover. 12. Shift fork, (3rd and direct). 13. Control lever. 14. Control housing cap. 15. Fulcrum ball. 16. Control lever spring. 17. Control lever ball. 18. ~ainshaft 3rd speed gear. 19. Interlock plunger. 20. Poppet spring. 21. Poppet ball. 22. ~ainshaft 2nd speed gear.
23. Synchronizer blocking ring. 24. ~ainshaft 1st and 2nd speed gear. 25. Shift fork, 1st and 2nd speed. 26. Poppet ball. 27. Expansion plug. 28. Poppet spring. 29. Clutch hub, 1st and 2nd speed. 30. ~ainshaft rear bearing retainer. 31. ~ainshaft rear bearing. 32. Rear bearing retainer seal. 33. ~ainshaft flange nut. 34. ~ainshaft. 35. Speedometer drive gear. 36. Snap ring. 37. C ounter shaft roller bearing. 38. Countershaft thrustwasher. rear, 39. Counter shaft.
PAINTED IN UNITEO STATES OF AMERICA
TRANSMISSION Section D Page 2

(c) Continue disassembly operation in the same manner as described in para graph (a), removing third and direct speed shift fork (12) and first and second speed shift fork (25), rails, ex pans ion plugs, poppet springs, balls and interlock plunger. CAUTION: In reassembling the control cover assembly, care shbuld be exer cised to see that all parts are replaced in their correct positions and none of the small interlocking parts are lost or omitted. (d) To remove control lever (13) from cover (11). turn off the housing cap (14) releasing retainer washer, spring (16) and fulcru'm ball (15). With the fulcrum ball and control lever assembly removed, the control lever pivot pin can be removed from cover.
A-22937
TRANSMISSION (MODEL T-98)

The Model T-98 transmission is of synchro mesh type having four speeds forward and one reverse. Fig. 2 illustrates the shift diagram.
CD
I
I
I
I
I
I I
CD
I
t-----
-----1------------.. N
I
I
I
I
I
I I
I
I
CD
CD
Fig. 2 - Shifting Diagram (T-98)

4. To remove the mains haft assembly:

With a few minor exceptions, the assembling is simply the reverse of disassembling. There fore the following disassembly instructions will also serve as reference for assembling. Fig. 1 illustrates construction details of this transmission and figure numbers in parentheses throughout this section will refer to this illu stration. 1. Clean outside of transmission particularly around the control and bearing covers (1,11,30). 2. Place control lever (13) into neutral position. Remove caps crews and lockwashers holding cover (11) to case (44) and lift control cover assembly off transmission. CAUTION: Do not force the control cover as sembly off the transmission. Forcing may spring the yokes and cause partial engagement or gear interference. A slight manipulation will free the cover. 3. To disassemble the control cover assembly: (a) Cut lock wire on reverse shift block and remove shift block lockscrew. Drive shift rail (10) out toward rear of cover driving out expansion plug (27) and remove shift block. (b) Pull tapered plug located on left out side of cover directly below poppet spring and ball and remove interlock plunger (19) and third and direct speed shift rail interlock pin.
(a) Lock transmission by engaging two speeds and remove flange nut (33). (b) Remove capscrews, five in number, and lift off mainshaft r ear bearing retainer (30) revealing speedometer gear (35), bearing (31), and snap rings. Slide speedometer gear (35) off of mains haft (34). Disassemble main drive gear bearing retainer (1) by removing capscrews and lockwashers, revealing main drive gear bearing (3) and snap rings (2) and (4). (c) Remove main drive gear bearing snap ring (2) and pull main drive gear (5) and bearing (3) out through front of case sufficiently to expose bearing snap ring (4). Apply bearing puller and re move bearing (3) from main drive gear (5). Tap mainshaft assembly toward rear of case and pull mainshaft rear bearing (31). Push mainshaft assembly through rear bore in case to clear main drive gear (5) and tilt front end upward and lift out through top of case. CAUTION: Be sure to catch pilot needle bearing, sixteen in number, when removing mainshaft assembly. When reassembling front bearing retainer (1). be sure to locate oil drain hole at bottom. 5. To disassemble main drive gear: (a) With the main drive gear bearing (3) removed fr om dr ive gear (5), it is lifted out through top of case.
L-L1NE MOTOR TRUCK SERV1CE MANUAL

6. To disassemble the mainshaft assembly: (a) Remove snap ring holding third and di rect speed clutch assembly and main shaft third speed gear (18) and slide clutch assembly and bushed gear from mainshaft. (b) Remove first and second speed hub retainer snap ring (36) and slide off synchronizer assembly. (c) Remove mains haft second speed gear snap ring (54) releasing thrust washer (53) needle bearing (50), thirty-four in number, second speed gear (22) and spacer (49). 7. To disas semble the countershaft assembly: (a) Remove caps crew (41) and lock plate (40) locking countershaft (39) and re verse idler shaft (42). (b) Using a brass drift, drive countershaft out through rear of case and lift the gear cluster (48) out through top of case. NOTE: The countershaft gear cluster turns on four sets of roller bearings (37, 52) which are loose in the bor e of the countershaft g ear. There are twenty-two rollers in each bearing set, totaling eighty-eight bearings, separated by spacer washers and spacer (46). These rollers will probably inter mingle with the main drive gear pilot bearing rollers (56) in bottom of case when the countershaft gear is removed. Countershaft rollers (37, 52) are slightly smaller than pilot bearing rollers (56). Be sure to pick up front thrust washer (51). rear thrust washer (38) and spacing washer from bottom of case. 8. To disassemble the reverse idler gear assembly: (a) Remove reverse shifting arm and drive reverse idler shaft (42) out through rear of case and lift idler gear (43) out through top of case. NOTE: When reassembling, be sure to position slot in shaft properly to take lock plate. 9. To disassemble the third and direct speed clutch assembly: (a) The rnainshaft clutch hub and sleeve are held together by two retaining springs located on each side of clutch hub. The clutch sleeve can be removed from clutch hub by removing the retaining springs and supporting the outside diameter of sleeve and pressing on
PRINTEO IN UNfTO STATES OF" AMERICA
TRANSMISSION Section D Page 3
hub. Use care when disassembling not to loose the three shifting plates (7). The blocker are supported by the main drive gear hub and third ,speed gear hub and are disassembled with the removal of the mains haft assembly. CAUTION: In reassembling the clutch assembly, be sure to place end of each retaining spring in the same shifting plate (7) with the loose ends located in same position on both sides to equalize the tension on all three shifting plates (7). and also index etched marking on hub and sleeve. 10. To disassemble first and second speed synchronizer unit: (a) The mains haft first and second speed clutch hub (29) and sleeve gear (24) are held together by poppet springs (28) and balls (26). The clutch hub (29) can be removed from sleeve (24) by supporting the outside diameter and pressing on the hub. Use care when disassembling as poppet springs and balls are under spring tension and may fly out when sleeve is removed. It is suggested that a cloth be wrapped around the assembly to guard against this.
TRANSMISSION REMOVAL (L-160 SERIES)

When it becomes necessary to remove the transmission on the above series trucks, it is necessary to disconnect and move to one side the front propeller shaft. This will per mit removal of the transmission. Proceed as follows. (a) Remove the bolts from the front end of the front propeller shaft at the joint flange (Spicer joints used.) (b) Remove the brake drum retainer bolts and slide the brake drum out of the brake band onto the propeller shaft. (This will provide maximum clear ance for the end of the propeller shaft to permit its being moved to one side.)
(c) Carefully pry the shaft end towards the rear and over the transmission main shaft flange and nut to permit the shaft to clear the flange. (d) Securely wire the shaft to one side to keep it out of the way while proceed ing with transmission removal.
TRANSMISSION Section E Page 1
TRANSMISSIONS (F-51 AND F-51-C)
Fig. I - (F- 51 an d F- 5J- C)

No.
1
Description
No.
Description
No.
Description
1. Main drive gear. 2, Drive gear bearing nut. 3. Front bearing retainer capscrew. 4. Main drive gear bearing retainer. 5. Retainer gasket. 6. Shift rail thimble. 7. Interlock pin. 8. Poppet ball. 9. Poppet spring. 10. Control cover. 11. Shifter fork lockscrew. 12. Shifter fork, 4th & 5th speed. 13. Shifterforklockwire. 14. Spring. 15. Retainer. 16. Dust cover. 17. Shift lever, and ball. 19. Mainshaft sleeve, 5th gear. 20. Mainshaft 5th gear. 21. Mainshaft3rdspeedwasher. 22. 3rd speed constant mesh gear.
23. Reverse idler roller bearing. 24. Reverse idler gear. 25. Reverse idler shaft. 26. Shifter fork, 2nd & 3rd speed. 27. Mainshaft 2nd & 3rd speed gear. 28. Shifter fork (low & reverse}. 29. Mainshaft low & reverse gear. 30. Mainshaft. 31. Control cover gasket. 32. Rear bearing cover gasket. 33. Speedometer drive gear key. 34. Speedometer drive gear. 35. Rear bearing retainer. 36. Mainshaft rear bearing grease seal. 37. Flange nut. 38. Flange lockwasher. 39. Flange. 40. Mainshaft rear bearing. 41. Countershaft rear bearing.
42. Countershaft rear bearing lock nut. 43. Drain plug. 44. Countershaft gear, 1st, 2nd & reverse.
45. Countershaft 3rd speed
gear. 46. Counter shaft 5th speed gear. 47. Mainshaft 5th gear washer. 48. Mainshaft 5th speed gear key. 49. Countershaft drive gear. 50. Spacer. 5!. Key. 52. Countershaft snap ring. 53. Countershaft front bearing washer. 54. Countershaft front bearing. 55. Countershaft front bearing retainer. 56. Expansion plug snap ring. 57. Mainshaft sliding clutch. 58. Main drive gear bearing. 59. Mainshaft pilot bearing.
PRINTED IN UNITEO STATES Of' AMERICA

Fig. 1 illustrates construction details of the F-Sl and F-51-C transmissions and figure numbers in parentheses throughout this section will refer to this illustration. Item (20) on Fig. 1 will be referred to as Mainshaft Fifth Speed Gear although due to change in diameter on F-51-C, direct in fifth transmission, it is used as fourth speed gear.
TRANSMISSIONS (MODELS F-51 and F-51C)

The Model F-Sl transmission (S-A-330) has five speeds forward and one reverse. Fifth speed is overdrive. Fig. 2 illustrates the shift diagram.
q)
I
I
I
<P
I
~
I

With a few exceptions, the assembling is simply the reverse of disassembling. There fore the following disassembly instructions will also serve as reference for assembling. 1. Clean the outside of the transmission, particularly around the control and bearing covers (4, 10. 35). 2. Place shift lever (17) to neutral position. Remove nine caps crews and lockwashers from control cover (10) and lift cover assembly and gasket (31) from top of case. 3. To disassemble the control cover assembly: (a) Cut lockwire (13) at fourth and fifth speed shift fork {12} and remove shift fork lockscrew (11). Drive shift rail out to ward front of cover driving out shift rail thimble (6) and remove shift fork (12). Do not lose poppet ball (8) and spring (9). (b) Remove interlock ball and pin retainer plug located on left outside of cover directly below the poppet spring and ball housing, releasing interlock ball and pin {7}. (c) Continue disassembly operation re moving low and reverse and second and third speed shift forks (26, 28). shift block, step pin, spring and rails. Do not lose shift rail poppet balls (8) and springs (9) or interlock pin (7) and balls. (d) Remove shift lever ball (18) from shift lever (17). Remove lever dust cover (16) and also nut and lockwasher from control lever pivot pin. Place cover (10) in a vise, grasp lower end of con trol lever spring (14) with a large pliers and twist it from its retaining lugs. Spring may also be removed by use of a pinch bar and for dng spring over the retaining lugs. The shift lever (17) may now be lowered through the control cover (10). Control lever pivot pin can also be removed from cover. CAUTION: In reassembling the controls, care should be exercised that all parts are replaced in their respective positions.
I I
I
-~--.I
r----I I
I
I I
I
I
<D
<P
r--I I
I I I I
I I I I
cD
A22886
Fig. 2 - Shifting Diagram (F-5J)

The Model F-Sl-C transmission (5-A-33) is constructed having five forward speeds and one reverse speed. Fifth speed is direct. Fig. 3 illustrates the shift diagram.
-----~
I I
I
I
cb
<b
A22882
Fig. 3 - Shifting Diagram (F-51-C)

4. Disassembling main drive gear and main shaft assembly:
(a) Lock transmission and disassemble flange nut (37), washer (38) and flange
(39). Remove six capscrews and lock washers from mainshaft rear bearing retainer (35). Lift retainer and gasket (32) from case. Slide speedometer drive
gear (34) from mainshait (30) and remove
speedometer gear drive key (33).
speed gear washer (47) on mains haft to index lugs with splines of shaft and then remove (Figure 4). Slide main shaft fifth speed gear (20) sleeve (19) and washer (21) from shaft.
6. To disassemble main drive gear:

(a) Remove peened over material from slots in main drive gear and turn off drive gear bearing nut (2). NOTE: Nut is left-hand threaded. Press bearing (58) from main drive gear (1).
(b) Drive mains haft assembly toward rear

of cas e sufficiently to expose rear bearing (40) snap ring. Install suitable
puller and pull bearing (40) from main
shaft (30).
(c) Remove six capscrews (3) and lock

washers from main drive gear bearing
retainer (4) and lift off retainer (4) and
gasket (5). Remove main drive gear (1) and bearing (58) and also main shaft pilot bearing (59) out through front
of case.
7. To disassemble countershaft and reverse idler gear:

(a) Remove peened over material from slots and r emove countershaft rear bearing nut (42) from countershaft (44). (b) Remove capscrew and lockwasher from reverse idler shaft lock plate and re move from slot in idler shaft (25). Drive idler shaft (25) toward rear of case and lift idler gear (24) and roller bearings (23) from case. (c) Drive countershait assembly (44) toward rear of case sufficiently to expose rear bearing (41), attach puller. and remove rear bearing from countershaft. Lift countershaft as'sembly through top of case, lifting front end upward and tilt ing assembly. Also remove front bear ing thrust (53). The countershaft front bearing is disassembled by removing snap ring (56) from groove and drive retainer (55) from case. The counter shaft front bearing (54) may now be removed from case. (d) To disassemble the countershaft as sembly, remove snap ring (52) from countershaft. Using adapter plates, press countershaft drive gear (49) spacer (50) fifth speed gear (46) and third speed gear (45) from counter shaft (44) and remove gear keys (51). CAUTION: In reassembling, NEW snap rings should be used throughout the unit
(d) Lift mainshaft (30) and gears out through top of case, tilting front end upward and leaving low and reverse speed gear (29) in case. With the mains haft as sembly removed, lift out low and re
verse speed gear (29) out of case.
5. To disassemble mains haft assembly:

(a) Slide mainshaft second and third speed gear (27) from mainshaft and also the mainshaft sliding clutch (57) from op posite end of mains haft.
....J
Washer
Fj g. 4 (b) Remove fifth speed gear key (48) from
groove in mainshaft (30). Rotate fifth
PRINTD!N UNITED STATES OF ... MERICA
, _ _
.. ..J
A22941
TRANSMISSION Section F Page 1
TRANSMISSIONS (F-52 AND F-52-C)
16
23
24
25
26
27
28
29
30
31
8..757
Fig. I - (F-52 and F-52C)

No. Description No, 20, 21. 22. 23. 24. 25. 26. 27. 28. 29. 30. 31. 32. 33. 34. 35. Description Countershaft gear key. Countershaft front bearing. Transmission case, Countershaft drive gear. Power take-off drive gear (right side). Countershaft overdrive gear. Countershaft 3rd speed drive gear. Drain plug. Reverse drive gear. Countershaft 2nd speed drive gear. Countershaft low speed drive gear. Countershaft rear bearing. Countershaft rear bearing lock nut. Rear bearing retainer. Mainshaft rear bearing. Speedometer drive gear.
r;;:.r
36. 37. 38. 39. 40. 41. 42. 43. 44. 45. 46. 47. 48. 49. 50. 51.
Description Mainshaft rear grease seal. Cotter pin.

Nut.
Washer. Mainshaft. Shifter shaft rear cove r. Shifter shafts. Mainshaft low and reverse sliding gear. Shifter fork (low and re verse). Shifter fork (2nd and 3rd speed). Mainshaft 2nd and 3rd spe ed sliding gear. Mainshaft 3rd speed constant mesh gear. Shifter shaft lock screw. Mainshaft gear lock washer. Constant mesh reverse idle gear. Reverse drive gear.
1. Shift lever. 2. Dust cover. 3, Spring retainer. 4. Spring. 5. Shift lever cover. 6. Capscrew. 7. Poppet spring cover. 8. Control cover. 9. Poppet spring. 10. Poppet ball. 11. Interlock pin. 12. Shifter fork {direct and overdrive). 13. Retainer gasket. 14. Main drive gear bearing. 15. Main drive gear bearing retainer. 16. Main drive gear. 17. Mainshaft sliding clutch. 18. Mainshaft overdrive gear. 19. Counter shaft bearing retainer.

Fig. 1 illustrates construction details of the F-S2 and F-S2-C transmis sions and figure numbers in parentheses throughout this section will refer to this illustration. Item (18) on Fig. 1 will be referred to as mains haft fifth speed gear although due to change in diameter on F-S2-C, direct in fifth transmission, it is used as fourth speed gear.
TRANSMISSIONS (MODELS F-52 and F-52-C)

The Model F-S2 transmission (S-A-430) is constructed having five forward speeds and one reverse. Fifth speed is overdrive. Fig. 3 illustrates the shift diagram.
G'
I
~
I
I I
~---~---~
I I
I
I
With a few exceptions, the assembly is simply the reverse of disassembly. There fore, the following disassembly instructions will also serve as reference for assembly. 1. Clean the outside of transmission, particu larly around the control and bearing covers (IS, 8, S, 33). 2. Place shift lever (1) to neutral position. then remove the holding capscrews and lift off the control cover assembly. CAU TION: Do not try to force the cover off, as it rna y spring the shifting yokes and cause gear interference. A slight manipu lation will free it. Disassemblingthe ontrol cover assembly: c
I
I
I I I
cD
3.
A-22SS1
Fig. 2 - ShiftIng Diagram (F-52)

The Model F-S2-C transmission (S-A-43) is constructed having five speeds forward and one reverse. Fifth speed is direct. Fig. 4 illustrates the shift diagram.
(a) Remove four capscrews and lift shift

lever cover assembly (S) from control cover assembly (8).
(b) Remove shift lever ball from shift

lever (1) and also dust cover (2). Re move nut and lockwasher from pivot pin. Place cover in vise, grasp lower end of control lever spring (4) with a large pliers and twist it from its lugs. Spring may also be removed by use of a pinch bar and forcing spring over the retaining lugs. With the spring removed, releasing spring retainer (3), the lever (1) can be lowered through shift lever cover (S).
<P
I
<P cp
I I I
I
-+-~
I
I
,
I
I I
~-----
I I
-1 I
(c) Remove caps crews (6) and poppet

spr ing and ball cover plate (7) re leasing poppet springs (9) and balls (10). Cut lockwire at reverse shift block and remove lockscrew. Drive shift rail (42) toward rear of cover driving out shift rail cover (41). Pull shift rail out releasing reverse shift block on inside of cover. CAUTION: Do not lose poppet spring (9) and ball
I
I I
I
I I
(2)
0)
A-22883
(10)
(d) Remove interlock ball retainer 'cap
located on left outside of cover directly below poppet spring and ball housing, releasing the interlock ball and pin
Fig. 3 - Shifting Diagram ( F-52-C)
(11)

(e)
Continue disassembly operation in the same manner as described in paragraph (c) removing the balance of shift rails (42), covers (41), shift forks (12, 44), poppet springs and balls and interlock ball. CAUTION: In reassembling the control cover assembly, care must be exer cised to see that all parts are replaced in their correct positions and none of the small interlocking parts are lost "Or omitted. 4. Disassemble mainshaft assembly: (a) After locking gears by engaging two speeds, the countershaft rear bearing nut (32) is removed from end of counter shaft. Remove rear bearing retainer (33). Slide off speedometer gear (35) and remove key. Drive mainshaft assembly toward rear of case sufficiently to expose rear bearing (34) snap ring. Install suit able puller and pull bearing (34) from mainshaft (40). By tilting the main shaft assembly front end upward, the entire unit comes out easily leaving sliding gears (46, 43) inside case. After shaft assembly is removed, the sliding gears may then be lifted out of case. To disassemble the mainshaft, slide the sliding clutch (17) from front end of shaft. Remove gear retaining washer key (Fig. 5).
remove. The bushed gears (18) (47) and sleeve are removed by using rear gear (47) to start the sleeve. Also remove the sleeve key from shaft.
5.
To disassemble main drive gear:
(a)
Remove four capscrews from main drive gear bearing retainer (IS). The main drive gear (16). bearing (14) and lock nut assembly can then be with drawn through front of case. Remove peened over material from slots in drive gear shaft (16) and turn off drive gear bearing lock nut. NOTE Nut is left-hand threaded. Press bear ing (14) from main drive gear (16)'.
(b)
6.
To disassemble countershaft and reverse idler gear:
(a)
(b)
(c)
To disassemble reverse idler gear, re move capscrew and lock plate from groove in idler. A simple method of pulling idler shaft, use a short piece of pipe, a long bolt having threads the same size as those tapped in end of shaft. Using a flat piece of steel with a hole in the center sufficiently large to permit passage of bolt. The nut is turned on the bolt close up to the head. The bolt is then passed through plate and pipe in order named and screwed into idler shaft. The nut is then tightened against the plate with the result that the pulling action is exerted against the shaft with the case acting as a base through the pipe and plate. After with drawing reverse idler shaft, the gears (50,51) are lifted from case and bear-' ings removed from idler gear. With thecountershaft rear bearing lock nut (32) removed, drive countershaft assernblytoward rear of case sufficiently to install suitable puller to remove rear bearing (31). By tilting the front end upward, the countershaft assembly is easily removed through top of case. Also remove front bearing thrust washer. To disassemble countershaft, remove retaining snap ring from countershaft. Countershaft gears (23, 24, 25, 26) should be pressed off, one at a time, and keys (20) removed from shaft. CAUTION: In reassembling, new snap rings should be used throughout the unit. When reassembling mainshaft assembly, always replace lock key and washer and make sure the gears are neither tight nor 10'ose after they are assembled. Make sure that all gears in the unit are replaced in their proper position.
(b)
(c)
,
...J
Washer
I _ _ _ .. .-1( '_
A.2294'
Fi g.
1+
After removing key, rotate gear re tainer washer until its inside lugs line up with grooves in the shaft and then
PRINTED IN UNITED S'TATES OF AMRICA
TRANSMISSION Section G Page 1
TRANSMISSIONS (F-54 AND F-54-B)
Fi g.
No. Description Shift lever. Dust cover. Sp ring r etaine r Spring. Shift lever cover. Capscrew. Lockwasher. Control cover. Interlock pin. Shifter fork (dir ect and overdrive) . Retainer gasket. Main drive gear bearing. Main drive gear bearing retainer. Main drive gear. Main drive gear bearing retaining nut. Mainshaft front bearing. Snap ring. Mainshaft sliding clutch. Snap ring. Expansion plug. Counter shaft front bearing. Spacer. No.1 23. 24, 25. 26, 27. 2B. 29. 30, 31. 32. 33. 34. 35. 36. 37.
3B.
- (F-54- and F-54--B)

Description No. 42, 43, 44. 45. 46. 47.
4B, 49. 50. 51.
Description Nut Cotter pin, Washer. Mainshaft rear grease seal. Mainshaft rear bearing. Rear bearing cover and speedometer housing. Gasket. Shifter shaft rear cover. Shifter shafts. Mainshaft low and reverse sliding gear. Shifter fork (low and reverse). Shifter fork (2nd and 3rd speed). Mainshaft 2nd and 3rd speed sliding gear. Poppet ball. Poppet spring. Mainshaft 3rd speed constant mesh gear, Shifter shaft lock screw. Mainshaft gear lock key.
1. 2. 3. 4. 5. 6. 7. B. 9. 10.
11. 12. 13. 14. 15. 16. 17. lB. 19. 20. 21. 22.
39. 40. 41.
Transmission case, Countershaft drive gear. Key. Power take-off drive gear. Mainshaft overdrive gear. Countershaft overdrive gear. Countershaft 3rd speed drive gear. Reverse drive gear. Countershaft 2nd speed drive gear. Drain plug. Mainshaft. Counter shaft. Counter shaft low speed drive gear. Countershaft rear bearing. Countershaft rear bearing lock nut. Countershaft rear bearing retainer. Snap ring. Snap ring. Speedometer drive gear.
52. 53. 54. 55. 56. 57.

5B. 59.
PRINTED IN iJNITED STATES OF .. MERICA

Fig. 1 illustrates construction details of the F-54 and F-54-B transmissions and figure num bers in arentheses throu hout this section will ref~r to this illustration. Item 27 on Fig. 1 will be referred to as mainshaft fifth speed gear although due to change in diameter on F-54-B, .direct in fifth transmission, it is used as fourth speed gear.
TRANSMISSION (MODELS F-54 and F-54-B)

The Model F-54 transmission (5-A-620) is constructed having five forward speeds and one reverse. Fifth speed is overdrive. Fig. 2 illustrates the shift diagram.
cp
I I
~~
I I
I I I
I
I
cp

With a few minor exceptions, the assembling is simply the reverse of disassembling. There fore, the following disassembling instructions will also serve as reference for assembling.
~---- - -+ - I I
I
I I
-1 I
1. Clean the outside of transmission, particu

larly around the control and bearing covers
(5, 13, 8, 47, 38).

2. Place shift lever to neutral position and remove the holdingcapscrews and lift off control cover assembly (8). CAUTION: Do not try to force the cover off, as you may spring the shifting yoke and cause gear interference.
I
I
o cD
A-22884
3. To disassemble control cover assembly: (a) Remove four capscrews (6) and lift shift lever assembly (5) from control cover assembly (8). (b) Remove shift lever ball from shift lever (1) and also dust cover (2). Remove nut and lockwasher from pivot pin. Place cover in a vise, grasp lower end of control lever spring (4) with a large pliers and twist it from its lugs. Spring may also be removed by use of a pinch bar and forcing over the retainer lugs. With the spring removed, releasing spring retainer (3), the lever (1) can be lowered through shift lever cover (5). (c) Cut lockwire and remove shift fork lockscrew (58), starting with upper shift rail (50). Drive shift rail (50) out toward rear of cover driving out shift rail cover (thimble) (49). Shift fork can be lifted out of cover. CAUTION: Do not loose poppet springs (56) and balls (55). (d) Continue disassembly operation re moving the balance of shift rails (50) interlock pin (9) shifter forks (52, 53, 10) interlock balls, shift blocks and stop pins. CAUTION: In reassembling the control cover, care should be exercised to see that all parts are replaced in their correct positions and none of the small interlocking parts are lost or omitted.
Fig. 2 - Shifting Diagram
(F-5~)
The Model F-54-B transmission (5-A-62) is constructed having five speeds forward and two reverse; Fifth speed is direct. Fig. 3 illustrates the shift diagram.
I
I
I
I
I
@
Fig. 3 - Shifting Diagram
(F-5~-B)

4. To remove mainshaft assembly: (a) Remove mainshaft rear bearing re tainer (47) and countershaft rear bear ing (3S). Slide off speedometer drive gear (41) and remove key. After lock ing gears by engaging two speeds, the counter shaft rear bearing lock Ilut (37) is removed from end of counter shaft. (b) Drive mains haft assembly toward rear of case sufficiently to expose rear bearing snap ring (40). Install suitable puller and remove bearing (46) from mainshaft (33). By tilting the main shaft assembly, front end upward, the entire unit comes out easily leaving sliding gears (51, 54) inside case. After shaft assembly is removed, the sliding gears may then be lifted out of case. (c) To disassemble the mains haft, remove the pilot bearing (16) and sliding clutch (IS) using the latter part to free the bearing. After removing key (59) (Fig. 4)1 rotate gear retainer washer until its inside lugs line up with grooves in shaft and then remove.
(b) Remove peened over material from slot in drive gear shaft (14) and turn off drive gear bearing lock nut (17). NOTE: Nut is left hand threaded. Press bear ing (12) from main drive gear (14).
6. To disassemble countershaft and reverse idler gears: (a) To disassemble reverse idler gear or gears, remove capscrews and lock plates from groove in idler shafts. A simple method of pulling shaft, or shafts, use a short piece of pipe, a long bolt having threads the same size as those tapped in end of shaft. Using a flat steel plate with a hole in the center sufficiently large to permit passage of bolt. The nut is turned on the bolt close up to the head. The bolt is then passed through plate and pipe in order named and screwed into idler shaft. The nut is then tightened against the plate with the result that the pulling action is exerted against the shaft with the case acting. as a base through pipe and plate. After withdrawing the idler shaft or shafts from case, the idler gears are lifted out through top of case and bearings removed froIn idler gears. (b) With the countershaft rear bearing lock nut (37) removed, drive counter shaft assembly toward rear of case sufficiently to install suitable puller to remove rear bearing (36). By tilting the front end upward, the countershaft assembly is easily reInoved through top of case. Also remove front bearing thrust washer (22). (c) To disassemble countershaft, remove re taining snap ring from countershaft. Gears (24) (26) (2S) (29) should be pressed off, one at a time and k~ys (25) removed from shaft. CAUTION: In reassembling, NEW snap rings should be used throughout the unit. When reassembling Inainshaft as sembly, always replace lock key and washer and make sure the gears are neither tight nor loose after they are assembled. Make sure that all gears in the unit are replaced in their proper position.
Main shaft
sliding clutch "" Main shaft,.
*"'1 ('"] (Jr
Main shaft ...............

gear./
~J
Washer
I _ .. _ '
(
.. .J
A2294J
Fig. 4
The bushed gears (27) (57) and sleeve are removed by using rear gear (57) to start the sleeve. Also remove sleeve key from shaft. 5. To disassemble main drive gear: (a) Remove four capscrews from main drive gear retainer (13), and lift off retainer. The main drive gear (14), bearing (12) and lock nut (15) can then be withdrawn through front of case.
AUXILIARY TRANSMISSION Section H Page 1
FULLER AUXILIARY TRANSMISSION - MODEL 2-A-45
33
32
31
Fi g.
No. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. Description Transmission case. Cork seal. Cork seal retainer. Shifting bar. Shifting bar eyebolt. Main drive gear. Cotter pin. Nut. Oil seal. Mainshaft bearing washer. Fr ont bearing spac er. Front bearing cover. Gasket. Counter shaft. Countershaft bearing nut. Countershaft front bearing cover. Gasket. Drain plug. Counter shaft fr<)nt bearing No. Description No. Description
II.
12. 13. 14. 15. 16. 17. 18. 19.
washer. 20. Countershaft drive gear. 21. Countershaft gear spacer. 22. Countershaft low-speed gear. 23. Countershaft rear bearing spacer. 24. Countershaft rear bearing washer. 25. Countershaft bearing nut. 26. Countershaft rear bearing cover. 27. Gasket. 28. Gasket. 29. Mainshaft washer. 30. Key. 31. ! Cotter pin. 32. Nut. 33. Mainshaft. 3:4. 10il seal.
35. Mainshaft. 36. Speedometer gear spacer. 37. Rear bearing cover and speedometer housing. 38. Breather pipe. 39. Cotter pin. 40. Breather pipe cap. 41. Rear support stud. 42. Oil retainer thimble. 43. Mainshaft low-speed gear sleeve. 44. Key. 45. Mainshaft low-speed gear bushing. 46. Mainshaft low-speed gear. 47. Mainshaft low-speed gear washer. 48. Shifting yoke. 49. Shifting yoke. 50. Oil deflector.
PRINTED IN UNITEO $'fA1S OF AMERICA
POWER TAKE-OFF
FOR FULLER MODEL 2-A-45 TRANSMISSION
4
fI
Fi g. 2
No. 1. 2. 3. 4. 5.
Description Gear. Gasket. Front bearing cover. Countershaft bearing nut. Bearing spacer. Key. Bushing. Gear sleeve. Gear washer. Gasket. Cotter pin. Nut. Mairishaft. Oil seal.
Rear bearing cover.
Mainshaft sliding clutch.
6.
7. 8. 9. 10. 11. 12. 13. 14. IS. 16.

The Fuller Model 2-A-45 Auxiliary Trans mission is designed to be used in conjunction with re gular transmissions. The gear ratios of the two-speed Model 2-A-45 Auxiliary Transmission are as follows: Direct--------l.OO to 1
Underdrive----l.3 to 1
The following procedure will be found help ful in servicing the unit:
20. Remove speedometer gear and key. 21. Remove inner bearing spacer. 22. Force lYlain shaft out of rear bearing through main drive gear bearing bore in front of case, removing main shaft underdrive bushed gear and washer as shaft emerges. 23. Remove main shaft pilot bearing from shaft. 24. Remove main shaft sliding clutch gear.
(A) Dismantle Transmission

1. Remove capscrews holding side cover or power take-off. 2. Remove cover or power take-off, and gasket. 3. Remove poppet spring retainer screw. 4. Remove shifter fork lock screw. 5. Withdraw shifter bar. CAUTION: Do not lose poppet spring and ball as shifter bar emerges. 6. Remove shifter fork. 7. Remove capscrews from countershaft front bearing cover. 8. RelYlove countershaft front bearing cover and gasket. 9. RelYlOve countershaft rear bearing cover capscrews. 25. RelYlove main shaft under drive gear sleeve washer from shaft. 26. Remove main shaft underdrive gear sleeve and key from shaft. 27. Force countershaft toward rear and out of case, removing countershaft front bearing spacer washer, countershaft drive gear, gear spacer, and counter shaft underdrive gear as shaft emerges. 28. Remove countershaft rear bearing lock nut and washer. 29. Press off countershaft rear bearing. 30, Remove countershaft rear bearing washer. 31. Remove countershaft front bearing from case.
(B) Assemble Transmission

10. Remove countershaft rear bearing cover and gasket. 11. Lock transmission gears. 1. Install countershaft front bearing in case, Install countershaft rear bearing washer on shaft. Press on countershaft rear bearing.
2.
12. RelYlove countershaft front bearing lock nut.
3,
13. Remove capscrews from main drive gear cover. 14. RelYlove main drive gear, bearings, and cover as a unit. 15. Press main drive gear from cover and bearing assembly. 16. Remove capscrews from main shaft rear bearing cover. 17. Remove rear bearing cover and gasket. 18. Remove main shaft rear bearing. 19. RelYlove rear bearing spacer. 8.
4. Install countershaft rear bearing lock nut and washer.

5. Install countershaft in position by in serting through rear bore in case,
6. Install countershaft underdrive gear, gear spacer, countershaft drive gear, and front bearing spacer washer as shaft progresses. 7. Install main shaft underdrive gear sleeve and key on shaft. Install main shaft underdrive gear sleeve washer on shaft.

19.
20. Install main shaft rear bearing spacer. Install speedometer drive gear and key. Install main shaft rear bearing spacer. Install main shaft rear bearing. Install rear bearing cover and gasket. Install rear cover capscrews. Install shifter bar through shifter fork, hub of shifter fork toward the rear. Insert poppet spring and ball in position. Push shifter fork into position.
9. Install main shaft sliding clutch gear

in position. 10. Press main shaft pilot bearing into position on shaft.
ll. Install main shaft rear bearing in pos ition in r ear bore in cas e.
21.
22. 23.
12. Insert main shaft assembly, previously prepared, through front bore in case and move toward the rear. Install rear bearing washer and main shaft under drive bushed gear as shaft pro gresses. 13. Install main drive gear bearing in position on main drive gear. 14. Install main drive gear bearing spacer. 15. Install main drive gear outer bearing. 16. Install main drive gear and bearing assembly in position in case. 17. Install main drive gear and bearing cover and gasket. 18. Install caps crews in main drive gear bearing cover.
24.
25.
26. 27.
28. Install poppet spring retainer screw. 29. Install shifter fork lock screw. 30. Install side cover or power take-off and gasket. 31. install capscrews holding cover or power take-off. 32. Fill transmission with lubricant (10 pints).
AUXILIARY TRANSMISSION Section I Page 1
BROWN-LiPE AUXILIARY TRANSMISSION - MODEL 5531
12
18
19
20
21
22
28
24
25
26
27
28
29
A-23183
Fig.
No. Description No. Description Counter shaft drive gear. Woodruff key. Drain plug. Power take-off gear. Woodruff key, Countershaft overdrive gear. Counter shaft underdrive gear. C ounter shaft. Countershaft rear bearing. Countershaft rear bearing shims. Countershaft rear bearing cap. Countershaft rear bearing retainer capscrew. Mainshaft rear bearing spacer washer. Mainshaft rear bearing. Companion flange. Mainshaft nut. Mainshaft rear oil seal cover. No.
3B.
Description
1. 2. 3. 4.
5. 6. 7.
B.
9. 10.
11.
12.
l3.
14. 15. 16. 17.

lB. 19.
20. Shifter housing. Shifter rod gland cover. 2l. Shifte r rod packing gland. 22. 23. Shifter rail - direct and 24. overdrive. 25. Mainshaft front bearing cap gasket. Mainshaft inner bearing. 26. Mainshaftfrontbearing cap. Mainshaft outer bearing. 27. 2B. Drive gear front bearing oil slinger. 29. Drive gear front bearing oil seal. 30. Drive gear oil seal cover. Companion flange. 31. Mainshaft nut. Drive gear bearing spacer. 32. Mainshaft drive gear. : Counter shaft front bearing. 33. Countershaft front bearing 34. retainer cap. 35. :Transmission housing. 36. Countershaftgear snap ring.
PRINTEO IN UNITED ST,to.TE5
37. Mainshaft rear oil seal. Mainshaft rear bearing retainer. 39. Mainshaft rear bearing
retainer gasket.
40. Mainshaft clutch gear.
41. Mainshaft clutch collar.
42. Breather assembly. 43. Overdrive and underdrive gear spacer. 44. Underdrive shifter fork.
45. Underdrive shifting rod.
46. Mainshaft underdrive gear. 47. Mainshaft overdrive gear. 4B. Shifter fork lock screw. 49. Shifter fork lock screw lockwire. 50. Mainshaft clutch collar. 51. Overdrive shifter fork. 52. Mainshaft clutch gear. 53. Mainshaft pocket bearing. 54. Main gears. 55. Main gear front bearing spacer shims.
or
AMERICA

(B) Dismantle Countershaft Assembly
1.
Remove countershaft front bearing cone.
The Brown - Lipe Model No. 5531 Auxiliary Transmission is constructed with three speeds forward, with Direct Drive on second speed and Overdrive on third speed. There are no speeds in Reverse. As an Auxiliary Transmission it is designed to be used in conjunction with standard four or five-speed transmissions. The Gear Ratios of the Brown-Lipe No. 5531 Auxiliary Transmission are: Direct--------- 1.00 to 1.00 Overdrive------ .72 to 1.00 Underdrive----- 2.00 to 1.00 The following instructions will be found helpful in servicing the unit; and it will be noted that the procedure is best handled in sections.
2. Remove countershaft rear bearing cone.
3. Remove snap ring from front of counter shaft.

4. Press off countershaft drive gear and remove key. 5. Press off countershaft overdrive gear and remove key. 6. Press off countershaft power take-off gear and remove key.
(A) Dismantle Transmission

1. Drain transmission. 2. Remove shifter housing capscrews and housing. 3. Remove companion flange nut -- front. 4. Remove companion flange nut -- rear. 5. Remove companion flange -- front. 6, Remove companion flange -- rear. 7. Remove power take-off covers and gaskets. 8. Remove countershaft rear bearing cover and shims. 9. 10. Remove countershaft front bearing cover and shims. Drive countershaft toward rear of housing, forcing rear bearing cup from position. Drop countershaft assembly to bottom of case. Remove main shaft rear bearing cover. Force main shaft assembly toward rear of case. Remove main shaft rear bearing, Tilt main shaft assembly and lift out through top of case.
(C) Dismantle Main Shaft Assembly

1. Remove underdrive clutch gear collar. 2. Remove uilderdrive clutch gear. 3. Remove main shaft underdrive gear. 4. Remove direct and overdrive clutch gear collar. 5. Remove direct and overdrive clutch gear. 6. Remove direct and overdrive gear. 7. Remove main shaft snap-ring.
(D) Dismantle Shifter Housing Assembly

1. Remove lockwires from shifter rail setscrews. 2. Remove shifter rail setscrews. 3. Remove poppet retaining plugs and spr ings. 4. Remove overdrive shifter rail. poppets and springs, and shifter fork. 5. Remove underdrive shifter rail, poppets and springs, and shifter fork. 6. Remove shifter rail packing glands and covers.
11. 12. 13. 14. 15.
(E) Dismantle Main Drive Gear Assembly

16.
17,
Remove drive gear and bearing from top of case, Remove countershaft assembly.
1.
Remove pocket bearing. Press off main drive gear bearing.
2.

(F) Dismantle Main Shaft Front Bearing
Cover Assembly
1. Remove front bearing oil seal. Remove front bearing oil slinger. Remove inner bearing race.
stalled with hub toward the front.) 4. Lock underdrive shifter fork in place with setscrew. 5. Lock direct and overdrive shifter fork in place with setscrew.
2.
3.
6. Install lockwires through shifter fork
(G) Assemble Countershaft Assembly

1. Press countershaft power take-off gear into place after installing holding key. Press countershaft overdrive gear and key into place. Press countershaft drive gear and key into place. Install countershaft gear lock-ring. Install countershaft front bearing cone. Install countershaft rear bearing cone.
setscrews. 7. Install poppet spring retaining plugs. 8. Install packing glands and covers for shifte r rails.
2.
(J) Assemble Transmission

3.
4. 1. Install countershaft front bearing cup in position in front of case. 2. Install countershaft front bearing cap and gasket. 3. Place countershaft and gear assembly in position in case. 4. Install countershaft rear bearing cup in place in bore of case. 5. Install countershaft rear bearing cap, gasket and shims. 6. There should be no perceptible bind or end play in the countershaft assembly. Make this assembly in such manner that there is a distinct drag felt and then add one .003" shim. Remove front countershaft bearing cap. Remove countershaft rear bearing cap gasket and shims. Drive countershaft assembly toward rear of case, forcing rear bearing cup from position in bore of case.
5.
6.
(H) Assemble Main Shaft Assembly

1. Install main shaft snap-ring in place on shaft. Install main shaft underdrive gear with clutch gear to rear of shaft. Install main shaft underdrive clutch gear with flat face toward rear of shaft. Install main shaft underdrive clutch gear collar with hub toward rear of shaft. 7 Install main shaft direct and overdrive gear with clutch gear to front of shaft. Install main shaft direct and overdrive clutch gear with flat face toward front of shaft. Install main shaft direct and overdrive gear clutch gear collar with clutch teeth toward the front.
2.
3.
4.
5.
8.
6.
9.
7.
10. Allow countershaft to lay in bottom of case.
(I) Assemble Transmission Shifter Housing Assembly

1. Install direct and overdrive shifter rail shifter fork, poppet ball and spring in place in housing cover. (Shifter fork must be installed with hub toward the rear.)
11. Press bearing cone against shoulder of main drive gear.

12. Place front bearing cover over main drive gear shaft. Install drive gear bearing spacer over shaft. Install shims over spacer. Install front bearing cone in cover. Install companion flange.
13.
2. Install shifter rail interlock.

3. Install underdrive shifter rail, shifter
fork, poppet ball, and spring in place in housing. (Shifter fork must be inPRINTED IN UNITED STATES OF AMERICA
14. 15. 16.
AUXILIARY TRANSMISSION Section I Page 4 17. 18.

30. Using bar through power take-off open ing, raise countershaft assembly into place. 31. Install countershaft rear bearing cup. 32. Bolt countershaft rear bearing cap, shim s, and gasket into place. 33. Bolt countershaft front cover and gasket into place. 34. Using bar through power take-off open ing, raise main shaft and gear assembly into place. 35. Install main shaft rear bearing. 36. Bolt main shaft rear bearing cap and gasket into place. 37. Install main shaft rear bearing oil slinger, oil seal, and dirt slinger in place. 38. Install companion flange. 39. Install companion flange nut and cotter key. 40. Install shifter housing and fork assembly in place with shifter forks in proper position. 41. Install shifter housing cover capscrews. 42. Install power take-off cover and gasket. 43. Fill with lubricant. (6 pints).
Install companion flange nut. There should be no perceptible bind or end play in the main shaft assembly. Make this assembly in such manner that there is a distinct drag felt and then add one .003" shim. Remove companion flange nut. Remove companion flange. Remove front cover, front bearing, and bearing spacer with shims. Bolt front main shaft bearing cover in place to housing. Install main drive gear and inner bear ing in position through top of case. Assemble drive gear bearing spacer, shims, and outer bearing as previously prepared. Install oil slinger, oil seal, and dirt shield. Install companion flange.
19. 20. 21. 22. 23. 24.
25. 26.
27. Install companion flange nut and cotter key. 28. Install main drive gear pocket bearing in hole in main drive gear. 29. Tiltrrain shaft gear assembly, previously prepared, and place in position in hous ing with pilot of shaft inside pocket bearing in main drive gear.
AUXILIARY TRANSMISSION Section J Page 1
BROWN-LiPE AUXILIARY TRANSMISSION

MODELS 6231 AND 6231-A
(FOR TEAR-DOWN ILLUSTRATIONS SEE SHOP TALK No. 38)
32
, 31
Fig.
No. Description No. Description tainer. Countershaft rear bearing. Counter shaft. Counter shaft rear bearing retainer. Power take-off opening. Drain plug. Counter shaft underdrive gear. Power take-off gear. Countershaft overdrive gear. Counter shaft drive gear. Countershaft bearing front. Bearing retainer (front). No. 27. 2B. 29. 30. 31. 32. 33. 34. 35. 36. 37. 3B. 39. Description Mainshaft overdrive gear. Needle bearings (47). Mainshaft pilot bearing. Sleeve (oil darn). Clutch gear. Mainshaft outer bearing (front) . Sleeve. Mainshaft inne r bearing (front) . Glutch collar. Mainshaft drive gear. Seal. Shift fork. Spacers.
Cover. Shift bar. 16. Shift fork. 17. Underdrive gear. lB. Needle bearings (47). Clutch collar. 19. 20. Clutch gear. Inner bearing (rear). 21. Outer bearing (rear). Slinger. 22. 11. Mainshaft. 23. 12. Mainshaft flange nut. 24. 13. Speedometer drive gear. 14. Speedometer driven gear. 25. 15. Mainshaft rear bearing re- 26.
l. 2. 3. 4. 5. 6. 7. B. 9. 10.

collar and underdrive gear. NOTE: Do not lose any of the loose needle bearings located in the underdrive gear. There are 47 rollers in each row of b~arings. 12. The mainshaft assembly can then be removed out through front of case and underdrive gear lifted out through top of case.
The Brown-Lipe Models No. 6231 and 6231-A auxiliary transmissions are constructed having three speeds forward. There are no speeds in reverse. As an auxiliary transmission it is designed to be used in conjunction with a standard trans mission. The gear ratios of the Brown-Lipe No. 6231 auxiliary transmission are: Direct Overdrive Underdrive 1.00 to 1 .69 to 1 2.14 to 1
13. Press out mainshaft rear, outer bear ing cup and use a brass drift and care fully drive out mainshaft front bearing cup. 14. Tap forward end of countershaft with soft hammer to drive out countershaft rear bearing cup.
The gear ratios of the Brown-Lipe No. 6231-A auxiliary transmission are: Direct Overdrive Underdrive 1.00 to 1 .86 to 1 1.24 to 1
15. Lift countershaft assembly out through

top of case and then remove countershaft front bearing cup.
The following instructions will be found helpful in servicing the unit:
(B) Dismantle countershaft assembly:

1. Remove countershaft rear and front
bear ing cones.
(A) Dismantle transmission:

1. 2. 3. 4. Drain transmission. Remove six cover retaining capscrews and lift off cover assembly and gasket. Remove companion flange nut and flange - front. Remove companion flange nut and flange - rear. Remove power take-off covers and gaskets. Remove countershaft rear bearing cover and shims. Remove mainshaft rear bearing re tainers, shims, gasket and speedometer drive gear. Remove seven main drive gear and bearing retainer assembly capscrews and lockwashers. Lift off main drive gear and retainer assembly, leaving pilot bearing in the drive gear. Remove clutch collar from front of mainshaft. Support mainshaft underdrive gear on blocks inside of front face of trans mission case. Press mainshaft out of rear bearings, underdrive clutch gear, 2. Remove snap-ring from front end of counte r shaft. 3. Press off countershaft drive gear and remove key.
4. Press off countershaft overdrive gear and remove key.
5. Press off countershaft power take-off

gear and remove key.
5.
(C) Dismantle the mainshaft assembly:

1. Remove underdrive clutch gear and collar. 2. Remove mainshaft underdrive gear.
6. 7.
3. Remove snap ring from front end of mainshaft. 4. Remove direct and overdrive clutch gear and collar. 5. Remove overdrive gear and roller bearings. NOTE: There are 47 needle bearings in each of the two rows used, with a spacer sleeve between the rows.
8.
9.
10.
(D) Dismantle shifter housing assembly:

1. Cut lockwires and remove shift fork lock screws. 2, Remove p.)ppet retaining plugs releasing balls and springs.
11.

3. Pull overdrive shift rail out through front of cover and remove shift fork. 4. Pull underdrive shift out through front of cover and remove shift fork. 5. Remove shift rails interlock pin and seals.
AUXILIARY TRANSMISSION Section J 3
(G) Assemble COW1tershaft assembly:

1. Press countershaft power take-off
gear into place after installing holding key. 2. Press countershaft overdrive gear into place after installing holding key. 3. Press countershaft drive gear into place after installing holding key. 4. Install countershaft gear sna,p ring. 5. Install countershaft front and rear bear ing cones.
(E) Dismantle main drive gear assembly:

1. Remove four oil retainer caps crews and lockwashers and lift off oil retainer and gasket. 2. Lift out spacing washer. 3. Press on end of main drive gear shaft to remove shaft, spacer sleeve, shims and inner bearing cone from retainer. NOTE: Keep shim pack together. 4. Press inner and outer bearing cups out of retainer together with oil sleeve. 5. Remove pilot bearing from main drive gear.
(H) Assemble mainshaft assembly:

1. Place mainshaft underdrive gear on flat surface and insert a little non-soap, viscous type, low melting point grease in the bore of the gear. Insert one row of roller bearings (47 rollers), and turn gear over and insert spacer. 2. Insert second row of bearings (47 rollers). Note that when all bearings are in place there is a space wide enough for another roller. Do not place another roller in the bearing row. The space is left to provide rolling clearance for all the rollers in that particular row. 3. Repeat roller installation as outlined in paragraphs (1 &: 2) with the mains haft overdrive gear. 4. Slide overdrive gear on shaft being careful not to disturb the rollers. 5. Place clutch gear on mains haft with flat face of gear toward front of shaft and install gear retaining snap ring. 6. Carefully place mainshaft underdrive gear, with bearings, on shaft with clutch teeth on gear toward rear and install clutch collar.
(F) Assemble the main drive gear assembly:

1. Install inner bearing race in the re tainer, then place the oil sleeve (or lubricant-darn sleeve) in the retainer with t he ridge of the oil sleeve toward inside of the retainer casting. Be sure to locate oil sleeve holes in proper location. The sleeve permits building up a reservoir of oil to assure front bearing lubrication. 2. Press in outer bearing cup. 3. Press inner bearing cone on the main drive gear and install spacer and shims. 4. Slide main drive gear shaft through retainer assembly and install outer cone. 5. Place suitable tubing over end of main drive gear shaft and against outer bear ing cone. Press against tubing to seat the bearings and shims. Approximately 30 tons pressure against sleeve will suffice to firmly seat the bearings. Bearing adjustment must be ,000" to .002" tight. 6. Install spacing washer and oil retainer on outer end of drive gear shaft retainer. 7, Install companion flange and nut draw down tight. 8. Install mains haft pilot bearing in main drive gear.
(I) Assemble transmission shifter housing assembly:

1. Install direct and overdrive shift rail, shift fork, poppet ball and spring, in place in housing cover. (Shift fork must be installed with hub toward rear.) 2. Install shift rail interlock pin. 3. Install underdrive shift rail, shift fork, poppet ball and spring in place in hous ing. (Shift fork must be installed with hub toward front.)

7. Holding the rnainshaft and gear assemhl~ together, with fingers in clutch co11a: groove, tilt the shaft, and install iJ case, being careful to hold underdriv( gear and clutch collar in position. 8. With the rnainshaft gears resting on thE countershaft, slide the underdrivE clutch gear through rear bore onto thE mainshaft and into the underdrivt clutch collar. NOTE: Beveled enc of gear toward rear of case. 9. Place overdrive clutch collar on direct and overdrive clutch gear with clutch collar teeth toward front. 10. Install main drive gear and retainer assembly previously assembled. 11. Install rear bearing cups, cones, speed ometer drive gear, and bearing re tainer with shims. 12. Adjust mainshaft assembly to obtain .000" to .003" loose bearing adjustment. 13. Install companion flange, nut and cotter key - tighten securely. 14. Install transmission cover assembly, being sure that the shifting forks engage clutch collars and tighten all cap screws securely. 15. Fill with specified lubricant per lubri cation section - (Capacity 8 pints).
4. Lock shift forks in place with set screws and install lockwires through setscrews. 5. Install poppet springs, balls and retainer plugs. 6. Install shift rail seals.
(J) Assemble transmission: 1. Install countershaft fr'ont bearing cup

in position in front of case. 2. Install front bearing retainer and gasket. 3. Place countershaft and gear assembly in position in case and tap toward front of case until gear contacts inside face of case. 4. Install countershaft rear bearing cup in place in bore of case. 5. Install rear bearing cap, gasket and shims. Add or remove shims at rear bear ing retainer to provide an adjustment of .000" to .003" loose. Such an adjustment will allow the counter shaft to revolve freely and with no perceptible end place or drag. 6. Remove front bearing retainer and proceed with the assembly.
WHEELS & RIMS Index Page 1
WHEELS AND RIMS qROUP

SECTION "A"
General . . . . . . . . . . . . . Front wheel bearing adjustment Rear wheel bearing adjustment. Oil seals - front wheels. Oil seals - rear wheels. Oil seals - rear wheels (Timken axles) Wheels and rims . . . . . . . . . . . . Wheel bolt nut tensions (disc wheels) . Page 1 1 I, 2
3 3
3, 4
3
3, 4
TIRES
SECTION "B"
Page Tire inflation. . . . . . Inflation . . . Overloading. Speeds . . . . Service load and inflation table.
4
2
3
Wheel, rim, and hub bolt tension application chart . .
4,5, 6, 7
PRINTED IN UNITEO STATES OF' AMA1CA
WHEELS &: RIMS Section A Page 1
WHEELS
General
Tapered roller bearings carry the wheels and are adjustable. Satisfactory operation and life depends upon correct adjustment and prop er lubrication. Every 3,000 to 5,000 miles re move the wheels, clean and inspect the bearings, races and wheel hubs. Then repack the bear ings, replace the wheels and adjust the bearings. Use a short fibre wheel bearing grease. Illustrations used in this section may vary due to the availability of Stamped, Cast and Budd wheels on various models, but the arrangement of bearings, grease seals and retainers are similar. Therefore, use illustrations for wheel mounting on the axle ONLY and disregard the design of wheel and brake. NOTE: R-I060 series axle (Semi-floating) rear wheel bearings are adjusted by shims lo cated between backing plate and end of axle housing. (See Fig. 1.) Remove plug and ins tall lubricator fitting as shown in Fig. 1 to lubricate bearing, re ins tall plug.
Front Wheel Bearing Adjustment

Use an 8 11 wrench and apply steady pres sure with one hand, pulling up the adjusting nut until a definite drag is felt on the wheel. Rotate wheel at the same time nut is being tightened to be sure that all parts are correctly seated. Back-off nut tofirst castellation and install new cotter pin. Front wheel bearings should never be given a loose adjustment for such will not permit the rollers and races to be in proper contact and bearing failure will result.
Fi g. 2
Fig. 2 illustrates construction details of rear wheel assembly on axles R-I060 series.
Rear Wheel Bearing Adjustment

Rotate wheel and tighten inner adjusting nut until a drag or bind is felt, then back off nut about 1/6 11 turn. Install lockwasher and outer nut, and after tightening securely, check the adjustment. There should be a very slight shake in the wheel (with axle shaft removed) if the adjustment is correct.
Grease guard Backing plate

reinforcement
Fig.
PRINTE.D IN UNITED STATES OF' AMERICA
Fig. 3
A22935
Fig. 3 illustrates construction details at rear wheel assembly on axles R-I070 series.
WHEELS & RIMS Section A Page 2
Fig. II-
Fig. 4 illustrates construction details at rear wheel assembly on axles R-1165 and R-1170 series.
Fig. 6
Fig. 6 illustrates construction details at rear wheel assembly on axles of R-l 741 series.
Fig. 5
Fig. 5 illustrates construction details at

rear wheel assembly onaxles of R-l440, R-1470,
R-l530, R-2470, R-2475, R-2490, R-1555,
R-l630, R-2580, R-2600, R-l540, R-l640,
RF-1455, RF-l575, RF-1670, R-2465, R-2466
and R-2585 series.
A-.2.2830
Fig. 7
Fig. 7 illustrates construction details at rear wheel assembly on axles of R-173l, R-18l 0, R-2741 and R-2800 series.

Oil Seals - Front Wheels
The front wheel oil seal should be inspected when hub or wheel is removed and replaced if necessary. When installing new seal, dip in light oil first and make sure it is properly in stalled in the hub to assure satisfactory serv ice. The machined surface of the steering knuckle must be clean and free of nicks and burrs so that sealing element can seat properly on the surface provided.
WHEELS &: RIMS Section A Page 3
Oil Seals - Rear Wheels

Place inner seal assembly in hub and drive carefully into place being sure that the seal bottoms and is aligned square with the hub. The outer seal is assembled into the bearing lock nut and is self adjusted on the axle shaft when the axle shaft is tightened against the hub. Machined surfaces of the axle housing and shaft must be clean and free of nicks and burrs to assure satisfactory service of the seals.
Install inner wheel bearing. (Bearing must be properly lubricated before installation.) In stall wheel hub assembly and outer wheel bear ing. Turn inner nut until it is tight against the outer bearing cone and at the same time revolve the wheel to seat the tapered bearings and oil seal. Continue to tighten the nut, while revolv ing the wheel until a definite drag is felt, and then back off about one-sixth of a turn. Place the locking washer on the axle with the lug in the groove. Place the washer against the nut so that the pin in the nut enters one of the holes in the washer, using either side of the locking washer to accomplish this. If it is necessary to turn the inner nut to bring the pin into line with one of the holes, install washer so that the least movement of the nut is ne~essary. Install outer nut and tighten securely. Install the outer oil seal wiper ring and gasket (Fig. 12). Place gasket inside cup of wiper ring and over end of axle housing end. Use adapter driv er and drive the outer wiper ring carefully onto the end of the axle housing until it seats fi rmly against the gasket. Place gasket against wheel hub as shown in Fig. 13. Install oute r seal assembly and place outer gasket over hub studs. Install axle shaft, ta pered dowels, lockwashers and stud nuts, and tighten securely.
Oil Seals - Rear Wheels (Timken Axles)

The inner and outer wheel hub oil seals mustbe properly installed to assure satisfactory service. Machined surfaces of component parts and sealing surfaces of wiper rings must be clean and free of nicks or burrs. The sealing elements must seat evenly on the wiper rings. Special tools (SE-1581) have been provided for proper installation of oil seals and wiper rings. The following illustrations show these tools in use for their specific application. Lubricate inner seat with wheel bearing grease and place on end of axle housing. Using inner seal adapter and driving sleeve, drive the seal carefully onto the end of the axle housing until it is seated firmly against shoulder on the housing (Fig. 8). Using a square as shown in Fig. 9, check from the end of the axle housing to the face of the sealing element at 90 0 intervals. The seal ing element should not be in excess of .010" off parallel with the end of the housing. Install inner seal wiper ring in wheel hub as shown in Fig. 10. The ring has one face ground and one face, polished. Position the polished face outward to contact the sealing element, and the ground face seated firmly against inner bearing cup. Following installation of the wiper ring, check installation using a .002" feeler gauge (Fig. 11) between the ring and bearing race. If the ring is in excess of .002" off parallel with the bearing cup, remove ring, check for dirt or other obstruction and reinstall.
PRINTED 1N UNITED STATES
Wheels and Rims

Wheel stud nuts should be inspected and tightened at regular intervals. Rim clamp nuts should be kept tight and the rim and tire align ment in relation to the wheel should be checked to make sure tire is running true. Where left- and right-hand thread studs and nuts are used, the left-hand thread nuts can be identified by a small groove machined around the flats and the studs, by letter "L" stamped on the head: Use left-hand nuts (stamped tlV!) on the left side of truck.
Wheel Bolt Nut Tensions (Disc Wheels)

KELSEY -HAYES WHEELS -- When tighten ing wheel bolt nuts on Kelsey-Haye s di sc wheels, do not use excessive leverage. Use a wrench of the same length as that furnished with the tool kit. BUDD WHEELS -- When tightening wheel boltnuts on Budd disc wheels, use wrench which will provide sufficient leverage to tighten as follows: (see next page)
or
AMERICA
WHEELS & RIMS Section A Page 4
9/16 11 Bolt -- tighten to 250 foot-pounds. (100 pounds pressure on a . 2-112 foot wrench.) 3/411 Bolt -- tighten to 350 foot-pounds. (140 pounds pressure on a 2-1/2 foot wrench.)
Fig. I I - Checking wiper ring a1 ignment.
Fig. 8 - Installing housing.
inner oil
seal
on axle
Outer seal wiper ring
Fig. 12 - Install ing outer wiper seal ring. Fig. 9 - Checking assembly. alignment of inner seal
Cakeb
~~.
Outer seal assembly ----~
Fig. 10 - Installing inner wiper ring in wheel hub.
Fig. 13 - Outer seal and gaskets installed.
WHEELS &
RIMS
Section B Page 1
TIRES
Tire Inflation
Proper tire inflation, tire loads, and road speeds are important determining factors gov erning tire mileage, and als 0 aifec t steering ease and maneuverability. Inflation pressures should be checked at regular and freq uent inter vals and the pressures maintained to specifica tions. Use an accurate tire pressure gauge.
Inflation
Inflation pre s sures should be checked when tires are cool. Never bleed a hot tire. The chart (Fig. 7) illustrates the loss in tire mileage caused by under inflation. It will be noted that a tire under-inflated only 20'10 will produce only 70"10 normal mileage.
% OVER INFLATION ) % UNDER INFLATION
----'
J % INFLATION
t#-==~---
92%
100%
70%
50%
25%
% EXPECTED NORMAL
SERVICE
AI6013
Fig. I - Inflation vs. Mi leage.

Over-inflation is also costly for a tire which is 20'10 over-inflated will produce only 92% normal tire mileage. "Bleeding" of air from hot tires should never be practiced. The pressure will be re duced but an increase in temperature will result as soon as the driving continues. The chart (Fig. 2) illustrates a condition where a tire was started cool with a pressure of 70 pounds, and at a temperature of 80 0 : ( 280 240 200 160
0 -
A-INITIAL CONDITIONS
B-AFTER 140 MILES
C-PRESSURE "BLED"
D-140 MILES AFTER "BLEEDING"
E-PRESSURE "BLED"
F-AFTER 200 MILES-TIRE FAILED
TEMPERATURE
fZ?Z?ZLl
(A) Initial conditions.

(B) After 140 miles of driving the pres sure had increased to 85 pounds and temperature to 200 0
PRESSURE
,.,
v::r
0 - -
v::
(c) The pressure was then "bled" to 70

pounds and an additional drive made of 140 rn.iles. Note the tern.perature. 120
0 -
90
r:; r:; r;: r:;
~
r%
~
~
1%
~
~
V
(D) The pressure had now increased to 73

pounds but the tern.perature increase was approxirn.ately 220 0 (E) Again IIbleeding"was resorted to. the tern.perature. Note
85 80 - 80 %r- -75 40' - 70 - 65 0 - 60
% ':_ ~ V
% /;
% ~r- ~I:/: v::
V ~I-
-~
V,:/': tV':
% r;: %f- %r~ '--f f
~ r
% %
A
r::
~
I----,
~ r--' D
rB
C
....
F
A16011
(F') After 200 rn.iles the tire failed from a

tern.pe rature of ove r 250 0
Fig. 2 - Effects of "Bleeding".
WHEELS &
RIMS
Section B Page 2
-~ "Oml",
\ "N,m.II,,'
#~~--
156'7.
100%
70%
50%
39'70
31'70
25%
% Expected normal service

A-J60J2
Fig. 3 - Overload vs. Mileage.
Overloading
Loading tires beyond their rated capacity is expensive, because tire mileages are rap idly decreased with overloads. The above chart {Fig. 3) illustrates how an overload of only 200/0 will result in tire mileage being only 700/0 of normal.
( % WASTED
) RUBBER
( % NORMAL \ TIRE MILEAGE

1FT=9"\\,
Speeds
Excessive speed is definitely one of the most important factors in loss of tire mileage. The chart (Fig. 4) illustrates how an increase in speed from40 to 50 m.p.h. results in an 1810 loss in mileage. An increase of speed from 40
to 60 m.p.h. results in a 3310 mileage loss.
.40 M. P. H.
50 M. P. H.
60 M. P. H.
AI610B
Fig.
ij -
Speed vs. Mi leage.

SERVICE LOAD AND INFLATION TABLE
TIRE SIZE PLY
RATING
32 LOADS AT VARIOUS INFLATION PRESSURES
WHEELS & RIMS Section B Page 3
36 1065 1215
40
45
50
55
60
65
70
75
80
6.00x16 6.00x20 6.00x20 6.50x16 6.50x17 6.50x20 6.50x20 7.00x16 7.00x17 7.00x17 7.00x18 7.00x20 7.00x20 7.00x24 7.50x16 7.50x16 7.50x17 7.50x18 7.50x20 7.50x20 7.50x24 8.25x17 8.25x18 8.25x20 8.25x20 9.00x18 9.00x18 9.00x20 9.00x20 9.00x22 9.00x24 9.00x24 10.00x18 10.00x20 10,00x20 10.00x22 10.00x24 11.00x20 11.00x20 11.00x22 11.00x24 11.00x24 12.00x20 12.00x22 12.00x24 13.00x20 13.00x24 l4.00x20 14.00x24
"6
8 6 6 6 8 6 6 8 8 8 10 10 6 8 8 8 8 10 10 10 10 10 12 10 12 10 12 10 10 12 12 12 14 12 12 12 14 12 12 14 14 14 14 16 16 18 18
990 1040 1135
1130
1225 1325 1290
1300 1400 1500 1600
1400
1400 1475 1500
1700
1700 1775
1550
1625
1700
1850
1950
1395
1485
1475 1575
1475 1575 1675 1525 1650 1750 1650 1775 1900
1775
1850
2000
2000 2075 2300 2375
2150 2475
2250
2575
1455
I
i
1560
1560 1650 1650 1750 1875
1760 1775 1875 2000
'1
1850
1900 2000 2000 2100 2125 2250 ,2250 2550 . 2200 2300 2475 2775 2950 3150 3375
i
2100
2200
2375
2375 2500 2700 2850 2470 2550 2750 2750 3075 3300 3500 3750 3450 3650
2600 . 2700
2975 , 3100
,~-
1950 2000 2175

..
2080 2150 2325 2600 2775 2950 3175
2330 2425 2600 2925 3125 3325 3575 3275 3475
--._
2585
2675
2900
2900 3025 3150
3225 3225 3450 3450 3675 3925 3925 3600 3825 3350 3600
i
3475 3725
3600 3850 4375
4100
i 4250
4175
i
3100 3275 3500 ' 3725 3700 3900 4100

i
3700 .3900 3950 i 4150 3900 4100
3775 4000 4000 4100 I - .4275 4250 , - 4550 4300 4300 4550 4800 4850 5150 5450
i
4350
4125 4350 4350 ,4575 4625 4900 5200
4500 4500 4750 5000 5000 5075 5375 5700
4675
4850
5200 . 5400 5275 5600 5925 6275 7025 7350 8225 7650 8525
I 6475
I
5775 . 6025 6750 7075 7900
Underscoring denotes maximum recommended loads. Duals will carry twice the load of corresponding singles.
WHEEL, RIM, AND HUB BOLT TENSION APPLICATION CHART
BOLT &: TRUCK NUT BOLT &: STUD STUD MODEL PART PART NO. SIZE PART NO. SERIES: L-IIO Bolt Bolt Stud Stud Stud Stud Stud Stud Stud Stud Stud Stud Bolt Bolt Bolt Bolt Bolt Bolt Bolt Bolt Bolt Bolt 69956-H 69955-H 96914-H 96915-H 96914-H 96915-H 81362-H ,8l363-H 96914-H 969lS-H 81368-H 81369-H 119343-H 75887-H 70647 -Rl 78193-Rl 78194-Rl 70647-Rl 78193-R1 78l94-Rl 78193-Rl 78l94-Rl 1/2-20NF 1/2-20NF 9/16-18NF 9/16-18NF 9/16-18NF 9/16-18NF 9/ 16 - 18 N 9/16-l8N 9/ l 6-18NF 9/l6-l8NF 9/16-18N 9/16-18N 5/8-18NF 5/8-11NC 1/2-20NF 3/4-16N 3/4-16N 1/2-20NF 3/4-16N 3/4-16N 3f4-l6N 3/4-l6N 3/4-16N 3/4-l6N 1/2-20NF 1/2-l3NC 5/8-l8NF 5/8-1lNC 1/2-20NF 1/2-l3NC 5/8-18NF 1/2-l3NC 5/8-18NF 5/8-llNC 3/4-16N 3/4-l6N 3/4-16N 3/4-16N
II-I/8-16N 1 1/8-16N 69958-H 69957-H 96916-H 96917-H 96916-H 96917-H 81364-H 81365-H 969l6-H 96917-H 81364-H 81365-H 12261-H 21814-H 12260-Rl 84712-H 84711-H 12260-Rl 847l1-Rl 847l2-Rl 83lS5-Rl 83l56-Rl
41419- V
4l420-V l2260-R1 22230- V 1226l-Rl 21S14-H 12260-R1 22230-V l2261-Rl 22230-V l226l-Rl 21S14-H 8471l-H 84712-H 41419- V 41420-V 83155-H 83156-H
TYPE BOLT
WHERE USED
TYPE WHEEL
APPLI CATION TENSION FT.-LBS. 80-90 80-90 175-200 175-200 175-200 175-200 175-200 175-200 175-200 175-200 175-200 17S-200 lS0-180 150-160 80-90 300-350 300-350 80-90 300-350 300-350 300-350 300-350 300-3S0 300-350 80-90 70-80 150-180 150-160 80-90 70-80 150-180 70-80 150-lS0 150 160 300-350 300-350 300-3S0 300-350 250-300 250-300
Hub to Wheel Hub to Wheel Hub to Wheel Hub to Wheel Hub to Wheel Hub to Wheel Hub to Wheel Hub to Wheel Hub to Wheel Hub to Wheel Hub to Wheel Hub to Wheel 4 4 4 Wheel to Drum Lug to Rim Wheel to Drum Hub to Wheel Hub to Wheel Wheel to Drum Hub to Wheel Hub to Wheel Wheel Wheel Wheel Wheel 4 2 4 4 4 2 4 2 4 4 to to to to Hub Hub Hub Hub
F&:R Kelsey-Hayes Rear Budd Front Budd Rear Budd Dual Rear Budd Rear Budd - Dual Rear Cast Front Budd
L-120
LM-120
L-120
L-120
L-120
L-150
L 150
L-lSO
Rear Budd
L-150
Rear Budd Dual
L-150
Bolt Bolt Bolt Bolt Bolt Bolt Bolt Bolt Bolt Bolt Stud Stud Stud Stud
I
82115 -Rl 6l883-Rl 119343-H 75887 -H S2115-RI 61S83-RI 119343-H 61S83-Rl 119343-H 75887 -H
80339-Rl 80340-Rl 69327-R2 6932S-R2
Wheel to Drum Wheel to Rim Whe el to Drum Lug to Rim Wheel to Drum Lug to Rim Wheel to Drum Lug to Rim Wheel to Drum Lug to Rim Hub to Wheel
Hub to Wheel Hub Hub Hub Hub to to to to Wheels Wheels Wheels
Wheels
Front Cast Rear Cast Front Cast Rear Cast - Single Rear Cast - Single Front Budd Rear Budd Dual
L-150
L-160
L-160
L-160
L-160
L 160

APPLI CATION I TENSION . FT.-LBS. l50-1S0 150-160 150-1S0 150-160 300-350 300-350 250-300 250-300 l50-1S0 150-160 SO-90 70-S0 150-1S0 150-160 40-50 150-160 150-1S0 150-160 150-1S0 150-160 150-1S0 150-160 SO-90 300-350 300-350 SO-90 150-160 150-1S0 150-160 l50-1S0 lSO-200 200-230 200-230 300-350 300-350 250-300 250-300 200-230 200-230 300-350 300-350 250-300 250-300
I
NUT BOL; III BOLT III STUD TRUCK PART NO. STUD: SIZE MODEL PART PART NO. I SERIES, L-l60 Bolt Bolt Bolt Bolt Stud Stud l19343-H 75SS7-H 7S167-R1 77602-Rl S0339-Rl S0340-Rl 5/S-1SNF 5/S-1lNC 5/S-1SNF 5/S-llNC 12261-R1 2lS14-H l2261-Rl 2lS14-H 414l9-V 41420-V S3l55-H S3155-H 12261-Rl 21S14-H 12260-Rl 22230- V 12261-Rl 2lS14-H 12259-Rl 21S14-H 12261-Rl 21S14-H 122bl-Rl 2lSl4-H 12261-Rl 21S14-H 122bO-Rl S4711-H S4712-H 122bO-Rl 21S14-H 12261-Rl 21S14-H
TYPE BOLT
WHERE USED
TYPE WHEEL
4 4 4 4
Wheel to Drum Lug to Rim Hub to Drum Lug to Wheel
Rear - Dual Cast Rear Dual
LF-170
LF-170
3/4--l6N 3/4-l6N 1-1/S-16N l-lIS-16N

5/S-lSNF 5/S-11NC
Hub & Drum to Whee Rear Hub & Drum to Wheel Budd Hub & Drum to Wheel Dual Hub & Dr'llm to Wheel 4 4 4 2 4 4 Wheel to Drum Lug to Rim Wheel to Drum Lug to Rim Hub to Drum Lug to Rim Hub to Drum Lug to Rim 4 4 4 4 4 4 4 Hub to Drum Lug to Rim Hub to Drum Lug to Rim Wheel to Drum Lug to Rim Hub to Drum Hub to Wheel Hub to Wheel Hub to Drum Lug to Rim Hub to Drum Lug to Rim Rear Cast Front Cast Rear Dual Front Steel Rear Cast Rear Steel Rear Cast Front Budd
LF-170
Bolt Bolt Bolt Bolt Bolt Bolt Bolt Bolt Bolt Bolt Bolt Bolt Bolt Bolt Bolt Stud Stud Bolt Stud Bolt Bolt Bolt Stud Stud Stud
119343-H 75SS7-H S2115-Rl 61SS3-Rl 7S167-Rl 77602-Rl X-4725-173 X-4725-172 1l9343-H 75SS7-H 7S167-Rl 77b02-Rl 119343-H 75SS7-H l44235-H 55539-Rl 55540-Rl 9l862-HA 91S72-H 61S30-HA 758S7-H 137991-H 54494-RI 69354-Rl b9355-Rl
L-170 & L-lSO L-lSO
1/2-20NF 1/2-13NC
5/S-1SNF 5/S-llNC
L-170& L-lSO L-lSO
3/S-24NF 5iS-llNC
5/S-1SNF 5/S-11NC 5/S-1SNF 5/S-11NC 5/S-lSNF 5/S-1lNC
L-170
L-170
L-170 &: L-lSO
l/2-20NF 3/4-l6N 3/4-16N 1/2-20NF 5/S-11 USS

5/S-1SNF 5/8-11NC 5/S-1SNF 3/4-10USS
L-190
4 4 4 4
Front Cast Rear Cast Rear Cast Real Budd Dual
L-190
L-l90
Wheel to Drum 4 l226l-Rl SAE-3135 Lug to Rim 54495-R1 13125S 13125S 41419- V 41420- V S3155-H 8315b-H 13125S 13125S 414I9-V 41420-V 83I55-H S3156-H 12261-Rl 21S14-H 4 4 Drum to Drum to Wheel to Wheel to Wheel to Wheel to Drum to Drum to Wheel to Wheel to Wheel Wheel Hub Hub Hub Hub Hub Hub Hub Hub
L-190
3/4-l6N 3/4-16N 3/4-16N 3/4-16N l-lI8-16N 1-1/8-l6N 3/4-16N 3/4-16N 3/4-16N 3/4-lbN
1-lIS-16N 1-lIS-lbN
L-190
Stud Stud
55575-H 55576-H
Rear Budd Dual Rear Budd Dual Rear - Dual Cast
L-190 L-190 Stud Stud I19343-H 75SS7-H
Wheel to Hub Wheel to Hub Hub to Drum Lug to Rim
5/S-1SNF 5/S-11NC
150-1S0 150-160
PRINTED IN UNITED STATIt.S OF AMERICA
WHEELS &. RIMS Section B Page 6
BOLT &: TRUCK NUT BOLT &: STUD STUD MODEL PART PART NO. SIZE PART NO. SERIES L-190 Stud Stud Stud Stud 119343-H 75887-H 55575-H 55576-H 5/8-18NF 5/8-llNC 3/4-l6N 3/4-l6N 3/4-l6N 3/4-l6N 1-1/8-l6N 1-l/8-16N 1/2-20NF 3/4-16N 3/4-l6N 3/4-16N 3/4-16N 1/2-20NF 5/8-llNC 5/8-18NF 5/8-IINC 3/4-l6N 3/4-l6N 1-1/8-l6N 1-1/8-l6N 5/8-18NF 5/8-1lNC 3!4-16NAT 3!4-l6NAT 3/4-l6N 3!4-16N 1-1/8-16N 1-1/8-l6N 5/8-l8NF 5/8-lINC 5/8-l8NF 5!8-llNC 12261-Rl 2l8l4-H 131258 131258 4l419-V 4l420-V 83l55-H 83l56-H l2260-R1 131258 131258 84711-H 84712-H 12260-H 2l814-H l2261-Rl 2l8l4-H 4l4l9-V 4l420-V 83l55-H 83l56-H l2261-Rl 21814-H 131258 131258 41419-V 41420-V 83155-H 83l56-H l2261-Rl 2l8l4-H l226l-Rl 2l8l4-H 131258 131258 4l419-V 41420-V 83155-H 83l56-H
TYPE BOLT
WHERE USED
TYPE WHEEL
I CATION I
150-180 150-160 200-230 200-230 300-350 300-350 250-300 250-300 80-90 300-350 300-350 300-350 300-350 80-90 150-160 150-180 150-160 300-350 300-350 250-300 250-300 150-180 150-160 300-350 300-350 300-350 300-350 250-300 250-300 150-180 150-160 150-180 150-160 200-230 200-230 300-350 300-350 250-300 250-300 150-180 180-200 150-180 180-200 200-230 200-230 300-350 300-350 250-300 250-300
APPLI
TENSION . FT .-LBS.
4 4
Hub to Drum Lug to Rim Drum to Hub Drum to Hub Wheel to Hub Wheel to Hub Wheel to Hub Wheel to Hub
Rear - Cast Dual Rear - Dual Budd
L-190
L-190
Bolt Stud Stud
55505-H 136339-H 136340
Hub to Drum Wheel to Hub Wheel to Hub Wheel to Hub Wheel to Hub Wheel to Drum Lug to Rim Hub to Drum Lug to Rim Hub Hub Hub Hub
&: &: &: &:
Front Budd
L-190
Bolt Bolt Bolt Bolt Bolt Bolt
ll9344-H 68333-H 78167-R1 77602-Rl 78l93-Rl 78194-Rl
4 4 4 4
Front Cast Rear Steel
LF-190
LF-190
Drum to Wheel Rear DrUITI to Wheel Budd Drum to Wheel Dual Drum to Wheel Rear Cast
LF-190
Bolt Bolt
ll9343-H 75887-H 48796-H 48797-H
4 4
Wheel to Drum Lug to Rim
L-204 &: Stud L-225 Stud
Drum &: 'Wheel to Hub Rear Drum &: Wheel to Hub Budd Dual Wheel to Hub Wheel to Hub Wheel to Hub Wheel to Hub 4 4 4 4 Wheel to Drum Lug to Rim Wheel to Drum Lug to Rim Hub to Drum Hub to Drum Wheel to Hub Wheel to Hub Wheel to Hub Wheel to Hub Rear Cast Rear Cast Rear Budd Dual
L-205 &: Bolt Bolt L-225 L-204 &: Bolt L-225 Bolt L-205 &: Stud Stud L-225
6l830-HA 75887-H 6l830-HA 75887"-H 69354-Rl 69355-Rl
I
1
3/4-l6N 3/4-l6N 3/4-16N 3/4-16N 1-1/8-16N 1-1/8-16N 5/8-18NF 3/4-10USS 5/8-l8NF 3!4-10USS
L-205 &: Bolt Stud L-225 L-204 &: Bolt L-225 Stud L-200 Stud Stud
7154l-Rl 54494-Rl 7154l-Rl 54494-Rl 61565-Rl 6l566-Rl
Hub to Drum 1226l-Rl 2 54495-Rl SAE-3135 Lug to Rim Hub to Drum l226l-Rl 2 54495-Rl SAE-3l35 Lug to Rim 131258 131258 4l4l9-V 41420-V 83155-H 83l56-H Hub to Drum Hub to Drum Wheel to Hub Wheel to Hub Wheel to Hub Wheel to Hub
Rear Cast Rear Cast Rear Budd
3/4-16N 3/4-16N 3/4-l6N 3!4-16N 1-1/8-l6N l-1/8-l6N

I
BOLT & iBOLT & STUD TRUCK 1 NUT i STUD MODEL IpART. PART NO. SIZE PART NO. I SERIES L-200 Stud Stud Stud 182820 31714-V 3171S-V
S/8-18NF 3/4-16AM.N 3/4-16AM.N 3/4-16AM.N 3/4-16AM.N S/8-18NF S/8-11NC 5/8-18NF S/8-1INC S/8-18NF 3/4-16N 3/4-16N 1-1/8-16N 1-1/8-16N 5/8-18NF 5/8-1 INC S/8-18NF 5/8-1lUSS 5/8-18NF S/8-11NC 3/4-16N 3/4-16N 3/4-16N 3/4-16N 1-1/8-16N 1-1/8-16N 3/4-16N 3/4-16N 3/4-16N 3/4-16N 1-1/8-I6N 1-1/8-16N

TYPE WHEEL
TYPE BOLT
WHERE USED
I APPLI CATION
TENSION 1FT .-LBS. lS0-180 300-3S0 300-3S0 300-3S0 300-3S0 lS0-180 lSO-160 ISO-180 lSO-I60 lSO-180 300-350 300-350 2S0-300 250-300 150-180 lSO-160 lSO-180 lSO-160 lSO-180 lSO-160 200-230 200-230 300-3S0 300-3S0 250-300 2S0-300 200-230 200-230 300-3S0 300-3S0 2S0-300 250-300 lS0-180 300-350 300-350 2S0-300 250-300 150-180 180-200 150-180 150-160 150-180 lS0-160 200-230 200-230 300-350 300-350 250-300 2S0-300
12261-Rl 1312S8 1312S8 84711-H 84712-H

12261-Rl 2I814-H
Hub to Drum Wheel to Hub Wheel to Hub Wheel to Hub Wheel to Hub Wheel to Drum Lug to Rim Wheel to Drum Lug to Rim Whe e 1 Wheel Wheel Wheel Wheel to to to to to Drum Hub Hub Hub Hub
Front Budd
L-200
Bolt B6lt Bolt Bolt Bolt Bolt Bolt
119343-H 68333-H 61830-HA 75887-H 119343-H 100568-H 100S69-H
4 4 4 4 4
Front Cast Rear Cast Front Budd
L-200
12261-RI 21814-H 12261-Rl 1312S8 1312S8 831S6-H 831SS-H 12261-Rl 21814-H 12261-Rl 21814-H 12261-R1 21814-H 1312S8 131258 41419-V 41420-V 8315S-H 831S6-H 131258 1312S8 41419-V 41420-V 8315S-H 83156-H 12261-Rl 131258 131258 831S6-H 83155-H
L-210
L-210
Bolt Bolt Bolt stud Bolt Bolt Stud Stud
119343-H 68333-H 115380-H 91872-H 119343-H 68333-H 48796-H 48797-H
4 4 4 4 4 4
Wheel to Drum Lug to Rim Wheel to Drum Lug to Rim ' Wheel to Drum Lug to Rim Hub to Drum Hub to Drum Wheel to Hub Wheel to Hub Wheel to Hub Wheel to Hub Hub to Drum Hub to Drum Wheel to Hub Wheel to Hub Wheel to Hub Wheel to Hub
Front Cast Front Cast Front Cast Rear Budd
L-210
L-210
L-210
L-210
Stud Stud
48796-H 48797-H
Rear Budd
L-210
Bolt Stud Stud Stud Stud Stud Stud Bolt Bolt Bolt Bolt Stud Stud
119343-H 54477-Rl 54478-Rl 54477-Rl 54478-Rl 71541-Rl 54494-Rl 61830-HA 75887-H 61830-HA 75887-H 61229-H 61228-H
5/8-18NF 3/4-16N 3/4-16N 1-1/8-16N I-l/8-I6N 5/8-18NF 3/4-10USS 5/8-18NF 5/8-11NC 5/8-18NF S/8-11NC 3/4-16N 3/4-16N 3/4-16N 3/4-16N 1-1/8-16N 11-1/8-16N
Hub to Drum Wheel to Hub Wheel to Hub Wheel to Hub Wheel to Hub
Front Budd
L-210
Wheel to Drum 12261-Rl 2 S4495-RI SAE-3135 Lug to Rim 12261-RI 2I814-H 12261-Rl 21814-H 131258 1312S8 4I419-V 41420-V i 83156-H 831S5-H I 4 4 4 4 Wheel to Drum Lug to Rim Wheel to Drum Lug to Rim Drum to Hub Drum to Hub Wheel to Hub Wheel to Hub Wheel to Hub Wheel to Hub
Rear Cast Rear Cast Rear Cast Rear Budd
L-2IO
LF-210
LF-210
PRINTED IN UNITED STATES OF' AcMERICA
MEMORANDA
MEMORANDA
MCarbHolllHC53E322B .. page 24 of 25
"
http://www.oldcarmanualproject.com/manualslCarbs/Holley/H...
,. . 24 of 25
...,
IHomel
iiI'.
CARBURETOR
DOWNDRAFT CARBURETOR
AUGUST 1953
SERVICE MANUAL
H\".. I..!;;" C,o,RBURETCP.
L!-:::tio IN
I.f~
COPYRJUMr'
1~3
co.
!=l..A.
i!!!!!!I!!I!lI!!!!iiiili!!!!i!!!ii!iiiiiillii!!!!iilll!!i!!ii!!!!l!liiiiii!!!liliiii!!i
U.S.A ....... PUBLICATIONS
DEPARTMENT
VAN
DYKE. MICHIGAN
.
lofl
~.
71:10/2009 9:llfi PM
MCarbHolllHC53E322B page 1 of 25
http://www.oldcarmanualproject.com/manuals/Carbs/Holley/H ...
I~ ~
1 of 25
~ ~I ~
12 .a 1: .!Hi 1 a a l!lll
CARBURETOR MODEL 1904
TABLE OF CONTENTS
DESCRIPTION
1. DESIGN 2. APPLICATION 3. MAJOR SUBASSEMBLIES OPERATION
1. FUEL INLET SYSTEM 2. MAIN WELL AND ECONOMIZER BODY 3. MAIN METERING SYSTEM 4. IDLE SYSTEM 5. POWER ENRICHMENT SYSTEM 6. ACCELERATING PUMP SYSTEM 7. CHOKE SYSTEM 8. DASHPOT OVERHAUL
1. INTRODUCTION 2. SPECIAL TOOLS AND IMPROVISED TOOLS 3. MASTER REP AIR KITS 4. DISASSEMBLY A. Preparation B. Disassembly-Main Body Assembly from
Throttle Body Assembly C. Disassembly-Main Body Assembly D. Disassembly-Throttle Body Assembly 5. CLEANING AND INSPECTION A. Cleaning B. Inspection 6. REASSEMBLY A. Reassembly-Throttle Body B. Reassembly-Main Body C. Reassembly-Main Body to Throttle Body
Assembly INSTALLATION
1. INSTALLATION ON THE ENGINE 2. CARBURETOR ADJUSTMENTS A. Adjnsting the Idle B. Adjnsting the Dashpot
PAGE
1
2
2
3
4
5
6
6
7
8
8
10
10
10
10
10
12
17
17
17
18
18
18
19
22
22
22
22
22
~ ~ ~
1 of 1
7/30/20099:42 PM
MCarbHollIHC53E322B . page 2 of 25
http://www.oldcarmanualproject.com/manuals/Carbs/Holley/H...
I~ ~
2 of 25
~ ~I
[8!i!iiiI
12 Q .4: fHi 18 .a 10 1112
INTRODUCTION
The Holley Carburetor Model 1904 is a notable advance in carburetion engineering. It combines the time-proved Holley characteristics of efficiency, dependability, and effective performance in a compact unit of outstanding simplicity. The elimination of the conventional air horn has resulted in a carburetor less than two thirds the height, but having a capacity comparable to units of standard design. By locating the choke plate in the venturi, the elimination of the air horn has been accomplished with no loss in efficiency or performance. In addition, the arrangement of the mixture discharging components in relation to the choke plate when open, aids in the distribution and vaporization of the fuel discharged into the airstream passing through the venturi. In line with the advanced engineering conception of this carburetor is the transparent fuel bowl of most versions of this carburetor model. This transparent fuel bowl greatly simplifies trouble shooting and carburetor servicing. Overhaul procedure also has been simplified by combining most of the fuel metering elements of the carburetor in a single, easily replaceable assembly. Close attention to design details has resulted in the improvement of various other parts. A spring arrangement is incorporated in the fuel inlet needle to cushion float movement and act as a vibration dampener to stabilize the fuel level on rough roads. The conventional economizer piston and accelerating pump piston have been replaced by neoprene diaphragms to insure more positive action and increased service life. This manual includes a full factory-approved overhaul procedure together with much valuable information on the description, operation, and adjustment of the Carburetor Model 1904. Careful adherence to the procedures given in overhauling this carburetor will insure the retention of the high standard of economical, efficient, and dependable performance, characteristic of all Holley products, which is delivered by this carburetor.
DESCRIPTION
ing lasting, effective, and dependable service. Most versions of this carburetor model contain a tempered glass fuel bowl which permits visual inspection of the float chamber. The action of the float and of the economizer stem during operation can be readily observed. Fuel level is clearly visible and the presence of water or sediment in the float chamber is readily detected. Fuel from the carburetor fuel inlet discharges below the fuel level in the float chamber to prevent foaming or splashing, assuring a constant, uninterrupted fuel flow to the metering components of the carburetor. Fuel in the float chamber circulates completely around the easily removable main well and economizer body which contains most of the fuel metering elements and passages. HOLLEY CARBURETOR MODEL This circulation has a cooling effect on the fuel being 1904 STANDARD ENGINE metered through the passages in the main well and economizer body. In addition to that factor, the high-lift 1. DESIGN design ofthe carburetor main well gives this carburetor The Holley C~buretor Model 1~4 is a .single-barrel. excellent hot operation and anti-percolation qualities. downdraft umt of advanced deSign. ThiS carburetor IS a model of noteworthy compactness and simplicity with its many new features assur Improved control of the power enrichment
~ ~ ~
1 of!
7/30/2009 9:44 PM
MCarbHolllHC53E322B . page 3 of 25
I~ ~
3 of 25
....I
121L1 fBi 1 8 !LW 1112 .l.a
system is assured by a unique diaphragm-type economizer. This type of economizer, which may be removed without disassembling the remainder of the carburetor, insures accurate response to variations in engine load conditions. These new features have been incorporated in this carburetor in cOrUunction with many of the time-proved engineering refmements found in other Holley carbureto models. The carburetor is fully sealed and balanced, wi all air bleeds and vents being open only to the air cleaner This filtered air supply gives added protection against th accumulation of foreign matter in the carburetor passage The main jet and other fuel metering components are individually flow tested to insure proper calibration ofth.,1:._ _ _ _ _ _ _ _ _ _ _ _ _ _~~---l carburetor. Smoother acceleration is assured by the HOLLEY CARBURETOR MODEL 1904 prolonged discharge of fuel provided by the spring WITH ALTITUDE ADJUSTMENT overriding feature of the diaphragm type accelerating pump. The fully-automatic vacuum-actuated power enrichment system of improved design provides the NOTE enriched mixture required for high power operation. Carburetor part numbers and other information applicable to specific I.H.c. vehicles may be obtained from the current Holley Carburetor Parts Catalog Sheets for these carburetors.
3. MAJOR SUBASSEMBUES
This carburetor model is composed of two subassemblies: the main body assembly and the throttle body assembly. The die cast main body contains the float and fuel inlet valve, the fuel bowl, the carburetor air inlet, the venturi, the choke mechanism, the economizer diaphragm and stem assembly, the accelerating pump, the main well and economizer body assembly, the main nozzle, and the pump discharge nozzle. Included in the main well and economizer body assembly are a large part ofthe various fuel metering components and fuel passages of the carburetor. The cast iron throttle body contains the throttle plate, the idle discharge ports, the distributor vacuum port, and the idle speed and mixture adjusting screws.
.......__ .. ,.
HOLLEY CARBURETOR MODEL 1904 FOR AUTOMATIC TRANSMISSION ENGINE
2. APPUCA110N
This carburetor model is used on the International Harvester Company 220 SD, 240 SD, 269 BD, 282 BD (C. O. E.), and 282 BD truck engines.
On the carburetor used with automatic transmission

engines, the dash pot assembly is mounted on a boss on the
side of the main body.
OPERATION
The fuel-air requirements of an automotive engine vary considerably throughout its range of operation. To assure effective carburetion, the carburetor must supply an efficient but economical
mixture for normal cruising conditions, a richer
mixture when a high power output is desired,
~13.
1 of 1
7/30/20099:45 PM
MCarbHollIHC53E322B - page 4 of 25
http://www.oldcarmanualproject.comlmanuals/Carbs/Holley/H...
I~ ~
4 of 25
Homel
12 J;HHHi 1 fi ~ 101112 13 14
enr:'
H,.'ll
N2-41!
FI!f.l
'~\l 'If
niP
enters the carburetor through the fuel inlet needle valve and a still richer mixture for a smooth idle and low and seat assembly and flows into the float chamber. The sp.eed performan~. In order to suppl~ the con:~ float, rising and falling with the fuel level in the float mixture to the engme under all operatmg conditions, h b th fu I' I dl' . . the Holley Carburetor Model 1904 has four basic fuel c am er, moves e e m et nee em !elation to Its metering systems. These are the main metering seat to regulate the amount. of fuel entermg the system, the idle system, the power enrichment system, carburetor. When the fuel m the float chamber reaches a and the acceleratmg pump system. In addition, there is specified level, the float moves the needle valve to a a fuel, inlet system "Yhich provides the four basic fuel position to restrict the flow of fuel. Only enough fuel to metermg systems Wlt~ a cons?IDt supply of fuel, and replace that being used will then be admitted. Any slight the. chok~ sy.stem whl~h provld~s ~ mean~ of tempo- change in the fuel level ca ses a corresponding rardy ennching the mixture to aid m startmg and u . . , running a cold engine. movement of the float, openmg or closmg the fuel mlet needle valve to inunediately restore the proper fuel level. The fuel inlet system must constantly maintain 1. RJEL INLET SYSTEM this s~ecified level of fu~l because th~ basic fuel metermg systems are cahbrated to dehver the proper The fuel inlet system provides the four basic fuel mixtures when the fuel is at the specified level only. metering systems and the choke system of the carburetor with a constant supply of fuel. This fuel, under pressure from the engine's fuel pump, A spring and pin inside the hollow fuel inlet
FUEL INLET SYSTEM
~ ~.
lofl
7/30/2009 9:45 PM
http://www.oldcarmanualproject.com/manuals/Carbs/Holley/H. ..
I..
5 of 25
1IHomel
12Q:tQ218a 10
1415
needle valve cushion the needle valve for protection against road shocks and vibration. A fuel valve clip, attached to the bottom of the needle valve, fits under the tab of the float lever to insure proper response of the needle when the float drops. A balance tube in the air inlet of the carburetor bore vents the float chamber to maintain balanced air pressures in that chamber, assuring proper fuel metering in all phases of engine operation.
2. MAIN WELL AND ECONOMIZER
BODY
P"~'AC:
':UWt
MAIN Mr.TIY.ING r..,Y")':-:M
o'~ ~,
,.-;::-.,.. 0 '''''IJ
~
D'" 11m )Y~Tf""
'o.... t, t,.,,~;,.:t1,
""[I, T SYSTeM
.AIR ~.\.~D; A"l:> V;:~',
I!irIll11 "'(";("l~[~"',l NO IllWUl.Jl r I.J "'F' ',Y 5 T( M
Fuel in the float chamber is distributed to the fuel passages of the four basic fuel metering systems through the main well and economizer body. A study of the passages in this assembly will insure a clearer understanding of the explanation of the operation of the four fuel metering systems.
10""'11
MAIN WELL AND ECONOMIZER
MAIN
N~Ulf
.'M h LI.~
~
'1
,1
\
<ODt
AIR
[~
_
-J
FLH
fUt~-"'IM W.llC'lJl(t
k'113
....l\II'l"'[ll
MAIN METERING SYSTEM
.~.
1 of 1
7/30/20099:46 PM
http://www.oldcarmanualproject.com/manuals/CarbsiHolley/H ...
I..
6 of 25
....,
IHomel
12.a.4Qfi18~
10
16
3. MAIN METERING SYSTEM

When the engine is running, the intake stroke of each piston draws air through the carburetor. As this air passes through the venturi of the carburetor, the drop in pressure in the venturi creates what is commonly called a vacuum. The strength of that vacuum varies in proportion to the velocity of the air flow through the venturi. This, in tum, is governed by the speed and power output ofthe engine. At normal cruising speeds, the difference between the normal, atmospheric air pressure in the float chamber and the vacuum in the venturi is used to operate the main metering system. This pressure differential draws a metered flow of fuel from the float chamber through the main metering system and out the main nozzle into the air stream in the venturi. When the fuel passes out of the float chamber, it is metered (or measured) by the main jet as it flows into the bottom of the main well. The fuel moves up the main well past the two narrow air bleed passages and enters the main nozzle. Filtered air from the carburetor air inlet enters the air
speed bleed and passing out the two narrow air bleed passages is mixed with the fuel flow in the main well. The high speed bleed meters a properly increasing amount of air into the fuel as speeds increase, stabilizing the fuel discharge and main taining the required mixture ratios. This emulsion of fuel and air, being lighter than the raw fue~ has a more instantaneous response to any change in venturi vacuum and is more readily vaporized than raw fuel upon being discharged into the air stream. The fuel flows through the main nozzle and is sprayed onto the open choke plate in the venturi. Airstream turbulence over the distribution pin and choke plate distributes the fuel over the lower portion of the choke plate where it is vaporized and mixed with the air flowing through the carburetor. The throttle plate controls the amount of fuel-air mixture admitted to the intake manifold, regulating the engine speed and power output in accordance with accelerator pedal movement. The distribution pin extending perpendicularly from both sides of the choke plate creates a turbulence as an aid to the proper distribution ofthe mixture to all cylinders of
.",
~on;,.
fl}t
>"(;, ;l.M
F4~'>..\CE~
.. JH
>jri~An' 5~\P:11J~:
')
~A1HWf::i
tnt
t: I ....:.,!... \ ..t:.. H(!I}\
;;;:-.:..1.;
IDLESYS1EM
.8 ..
10fl
7/30/2009 9:46 PM
http://www.oldcarmanualproject.com/manuals/Carbs/Holley/H-..
I~ ~
7 of 25
.... I
IHomel
12 Q .4di fi 1 a ~ 10 11 12 13
1617
;\t the idle and low speeds,. the velocity of the air flowmg through the carburetor IS reduced and the vacuum created in the venturi will not be strong enough to operate the main metering system. Because of the restriction of the air flow through the carburetor due to the nearly closed throttle plate, intake manifold vacuum will be high. This high manifold vacuum provides a pressure differential which is used to operate the idle system.
smooth, even transition from idle to cruisin

S.
d g spee s.
PO~ER ENRICHM ENT SYSTEM
When high power output is required, a richer mixture must be prov~ded than is required for normal cruising when no great load IS pl~ed on the engine. The carburetor provides the added fuel for high power operation by means of the power enrichment system, sometimes called the economizer system.
At the idle, fuel flows through the main jet into the The power enrichment system is actuated by manifold bottom of the main well. The high manifold vacuum acting on this fuel through the idle system passages vacuum. Manifold vacuum, which is strongest at the idle draws the fuel from the main well through a short when there is no load on the engine, is reduced in proportion horizontal passage into the idle well. A calibrated to the increase in engine loading. This is due to the fact that, restriction in the lower portion of the idle well meters the as the load on the engine is increased, the throttle plate must flow of fuel entering the idle system. The fuel passes out be opened wider to maintain any given speed. Manifold the top of the idle well and into the idle system passages vacuum will be reduced because the restriction offered to in the main body. A metered flow of air from the idle air the air flow entering the intake manifold by the throttle plate bleed is admitted to the fuel as it enters the idle passage will be lessened as the plate is opened. The strength ofthe in the main body. The idle air bleed also serves to vent manifold vacuum is thus an accurate indicator of the power the idle system to prevent any siphoning effect at higher demands placed on the engine.. speeds or when the engine is stopped. This mixture of fuel and air continues down, flowing through the idle . . . . restriction and, passing the two idle transfer holes in the Matufold vacuuI? actmg on the eco~omJzer dIaphragm throttle body, is discharged through the idle discharge actuates th~ power ennchment system. ThiS vacuum from, the hole into the strong manifold vacuum existing below the lower portion of the throttle bore below the throttle plate IS throttle plate. The two idle transfer holes act as additional transmitted through the vacuum passage to the vacuum chamber air bleeds at the idle. An idle adjusting needle, which on !o.p of the economizer diaph~agm, At idle and n.onnal . seats in the idle discharge hole, controls the discharge of c:Ulsmg sp~eds, the vacuum actmg on th~ economizer fuel at the idle and provides a means for adjusting the diaphr~ IS stron~ enough to h~ld the ~1ap?ragm up agaills~ idle mixture of the engine. Turning the idle adjusting ~e tenSIOn of the diaphragm. sprmg. ThiS rruses the economizer needle in moves the pointed tip of the needle closer to its dl~phragm s~m clear of the t:~wer valve and.the po:ver v~lve seat, restricting the fuel flow out of the idle discharge wlll be held ill ~e closed POSItiO~ by the te~slOn of.lts ~prmg. hole. This results in a leaner idle mixture. Conversely, The power enrIchment system wtll thus be moperatIve m turning the needle out allows more fuel to flow out the conditions of high manifold vacuum. idle discharge hole to provide a richer idle mixture. During off-idle operation, which occurs when the throttle plate is moved open slightly past the two idle transfer holes, each hole begins discharging fuel as it is exposed to manifold vacuum. As the throttle plate is opened still wider and engine speed increases, the velocity of the air flow through the carburetor is also increased. This creates a vacuum in the venturi strong enough to bring the main metering sYstem into operation. The flow from the idle system tapers off as the main metering system begins discharging fuel. The two sYstems are engineered to provide a When high power demands place a greater load on the engine, manifold vacuum is reduced. When the vacuum is reduced below a predetermined point, the diaphragm can no longer overcome the tension of the diaphragm spring and the stem will be forced down. This depresses the pin in the center of the power valve, opening the valve. Fuel from the float chamber will flow into the valve and, passing through a horizontal passage, enter the main well. There it is added to the fuel flow of the main metering system, enriching the mixture for full power. The drilled plug in the passage between the power valve and the main well is a calibrated restriction which meters the flow of fuel through the power enrichment system.
[3 ..
1 of!
7/3012009 9:47 PM
http://www.oldcarmanualproject.com/manualslCarbs/Holley/H. ..
I~ ~
8 of 25
~ ~I
IHomll1
12 Q1, li .61.8. ~ 10
12 13 14 15 16
_n.LL
(cor
_ MANlfOLJ V)\C1..,l."i
Vb.ClJUM
I'A;5AG~
rt, .
.t t~
POWER ENRICHMENT SYSTEM
provided by the pump spring assures an even, prolonged discharge of fuel regardless of how suddenly the throttle The air flowing through the carburetor responds ahnost is opened and cushions the action of the pump to prevent immediately to any increase in throttle opening. There is, damage to the pump linkage due to those sudden throttle however, a brief interval before the relatively heavier fuel-air movements. mixture in the narrow carburetor passages can gain speed and , maintain the desired balance of fuel and air. The accelerating The fuel, under pres.sure from the dIaphragm, .flows pump system operates during this interval, supplying fuel untithrough.the pump dIscharge passage and: forcmg the the other systems can provide the proper mixture. pump dIscharge ball check valve and weIght up, passes into the pump discharge nozzle screw. The pump When the throttle is closed, the pump return spring forces the discharge ball check valve seals the passage when the pump is not discharging fuel. The hexagonal weight holds pump diaphragm toward the back of the pump chamber, drawing fuel into the chamber through the pump inlet. The the ball check valve on its seat to prevent a loss of fuel pump inlet contains a baU check valve which opens to admit from the pump chamber due to the siphoning effect of the fuel from the float chamber into the pump chamber, and clos~rstream at high engine speeds. when the pump is operated to prevent a reverse flow of fuel. Flowing up the hollow pump discharge nozzle screw, the fuel passes out holes in the head of the screw into the When the throttle is opened, the movement is transmitted by pump discharge nozzle and is sprayed into the airstream the pump link to the pump operating lever. That lever presses in the venturi. A slot cut into the pump discharge nozzle the pump rod sleeve inward, compressing the pump spring, vents the system to prevent the pump discharge baU check The pump spring, in turn, presses on the diaphragm, forcing valve and weight from being lifted and fuel drawn from the fuel from the pump chamber into the pump discharge the pump chamber by the siphoning tendencies of the passage. The "overriding" feature airstream at high engine speeds.
6, ACCELERATING PUMP SYSTEM
~~~
1 of!
7/30/2009 9:48 PM
MCarbHollIHC53E322B - page 90f25
http://www.oldcarmanualproject.com/manualslCarbs/Holley/H ...
I~ ~
9 of 25
~ ~I
[Home I
123.1dHi1B.9.10 1112 13 H
16171819
tOUk
.~'_tL
1l2"h!
ACCELERATING PUMP SYSTEM
7. CHOKE SYSTEM
8. DASH POT
n a coldengine, much of the vaporized fuel from the :arburetor condenses to a liquid on contact with the low lressure area and cold surfaces of the intake manifold. This -esults in an inefficient distribution of fuel to the cylinders, :ausing hard starting, rough running, stalling, and loss of lower. The choke plate is the means used to provide an :nriched flow of fuel to aid in starting and warming-up a :old engine. Closing the choke plate which is located in the rentur~ confines manifold vacuum within the carburetor md draws a rich flow of fuel from the idle and main netering systems. When the engine starts, enough air is lrawn through the spring-loaded poppet valve in the choke llate to enable the engine to run and to prevent flooding. rhe throttle plate opening is increased by the fast idle cam luring choking to allow the engine to operate at a mst idle o prevent stalling. The fast idle cam, which is a curved :xtension of the choke lever, contacts the throttle stop screw md prevents the throttle plate from closing completely '{hen the engine is choked.
Engines equipped with automatic transmissions require an anti-stall device as protection against loading the engine when the accelerator pedal is suddenly depressed and released. This protection is provided by the dashpot. The dashpot retards the closing rate of the throttle plate as it approaches the idle position, allowing the engine to dissipate the raw fuel discharged into the intake manifold by the accelerating pump. The dashpot slows the final phases ofthrottle plate closing by means of a spring-loaded diaphragm. When the accelerator pedal is released, the throttle return spring in the throttle linkage closes the throttle plate simultaneously with the release of the pedal. As the throttle plate approaches the idle position, a tab on the throttle lever contacts the lower edge of the dashpot lever. This rotates the dash pot lever, causing the head of the dashpot adjusting screw of the dashpot lever
~13~
1 of 1
7/30/2009 9:48 PM
MCarbHoIlIHC53E322B page 10 of 25
http://www.oldcarmanualproject.com/manualsiCarbs/Holley/H ...
I..
10 of 25
IHomel
12.3.1 Q fi 1 aft 10 1112 13 14 15 16
18 19 20
DASHPOT(AUTOMATIC TRANSMISSION)
to impinge on the dashpot diaphragm rod. As the rod is moved into the dashpot, the tapered step of the rod engages the diaphragm washer. Continued movement of the rod will cause a corresponding movement of the diaphragm, compressing the air in the diaphragm chamber above the diaphragm. The compressed air bleeds out of the diaphragm chamber through a groove in the seat of the diaphragm washer, retarding the closing speed of the throttle plate. This allows the engine to properly use the charge of accelerating fuel, preventing
stalling from an over-rich condition in the manifold. When the throttle is again opened, the pressure is released from the dashpot diaphragm rod and the dashpot return spring moves the rod off its seat in the diaphragm washer. This allows air to flow back into the diaphragm chamber. After moving the rod off its seat, the spring returns the rod and diaphragm to their original position.
OVERHAUL
1. INTRODUCTION
The proper overhaul of the carburetor requires that it is completely disassembled and each part is thoroughly cleaned. Each clean part should then be examined for signs of wear, damage, or deterioration. Defective parts should be
replaced with genuine Holley replacement parts aud the carburetor should be carefully rebuilt. Care in rebuilding and accuracy in adjusting the carburetor will insure the continuation of the characteristics of power, economy, and performance engineered into every Holley carburetor.
IB
lofl
7/30/2009 9:49 PM
I~ ~
11 of 25
~ ~I
IHome I
12.3..4 Ii.61 ~U! 10 1112 13 14 15 16 17 18 19 20 21
2. SPECIAL TOOLS AND IMPROVISED TOOLS This carburetor may be overhauled using ordinary tools if a reasonable amount of care is exercised. Overhaul will be facilitated, however, and damage to parts avoided if factory-approved tools are used. The special tools recommended for use in the overhaul of this carburetor are listed below. SNAP-ON TOOL NO. TMC-36 MC-128 MC-I64 HOLLEY TOOL 82R-49 82R-34 82R-53
TOOL Main Jet Wrench Power Valve Wrench (Used for fuel inlet seat retainer screw) Float Gauge
[n addition to the special tools listed above, a simple tool for removing or installing the distribution pin may be mprovised. Obtain a section of brass tubing at least three nches long with an inside diameter of 118 inch (or slightly .arger if that size is not 0 btainab Ie), a length 0 f 118 inch or .arger drill ro d (or a flat-tip punch having an end diameter )f a least 118 inch), and a length of No. 52 or 1/16 inch diameter drill rod. "These improvised :ools are to be used as described in the overhaul 3rocedure that follows. 3. MASTER REPAIR KITS The Master Repair Kits contain Holley replacements for parts which are subject to wear or may be iamaged in disassembly. The disassembly procedure neludes instructions to discard all parts for which :eplacements are provided in the Master Repair Kit. The proper kit for this carburetor is listed in the :urrent Holley Carburetor Parts Catalog Sheets for ;bese carburetors. 4. DISASSEMBLY A. PREPARAnON During disassembly, use separate containers for the component parts of both major subassemblies; the main body assembly, and the throttle body assembly. Cleaning, inspection, and reassembly will be facilitated by use of separate containers. B. DISASSEMBLY-MAIN BODY ASSEMBLY FROM THROTILE BODY ASSEMBLY The following list contains all parts removed in separating the main body assembly from the throttle body assembly. Parts to be discarded and replaced from a Master Repair Kit are marked with an asterisk (*).
-10
,.,;.;;
""t'
"'"
2
,,'"
f-".
PART NAME
Pump Link Cotter Pin Throttle Body Screws and Lockwashers (2) Throttle Body Gasket
c..-=~.::;;:::.~<_:>_3
--.~;: '':~'''''''.-'
,\"l
1',/8
N~--II~
~;Jn
Figure I. Disassembly - Two Maier Subassemblies
~ ~ ~
10fl
7/30/20099:49 PM
I~ ~
12 of 25
~ ~I
IHomel
2 ~.1 Q!i 1 ~ ~ 10
12 13 14 15 16 17 18 1920
\\
'\,
'\
\\
\\ '..J.
'MIt::,-r
~()~.
I
1{.1-l:II}
figure 2. Removing Pump Link Cotter Pi.,
'*=
~."-"".:J
Figure 3. RemovIng Throttle BodY
!.~ .... w.
(1) Remove and discard the upper pump link cotter pin. Disengage the upper end of the pump link from the pump operating lever.
(2) Remove the two throttle body screws and lockwashers. Separate the throttle body and main body and discard the throttle body gasket.
39...... yll I
IV!_
I, I
:17
H
17
16
40 .......,; .Q;)'-.
,t....:J,.:J4I
.u ---_(:~i .
~5~_~ . .
IA
"'"
~'S: ~.~
, \
t\
1
-:
'
10
I;
fY~
,
.
43--
~'-.- ~
I
_-~!r
~](.
'-~..lR'li:
4(,-c:..~ 41 , \ 4'l~.
Ii?
T ,~"J ~'.,
\
L r;;;<-J ~ ~'ill~I rJ,f.:r7'~rf.f~~;01 Il'l~~~j ~.-. I b~ .. ~" ~/ . ~.'
,(
\I
'f
I
15
'
1
~
.' .:__ 11
..
~ ,
2
~
. IA
i~~~~~
/r
1.1
la~"
,-...,.-.
\
~':!5 ~, ::n/ . ~-~ ~ l ~: 1/ ~.J~.

l~ ~tl'a:~:/..
" .e'~
n
H '?B
A ."'
I
,};;..
.~
1",1.
"
,.
.1, .JI
~ J
\!f~'
",4Ii
AUlo"".... rl( HiII\i~MI~~ION V,KDUKHOK PA,{ b
R3-421A
FIGURE 4. DISASSEMBLY - MAIN BODY ASSEMBLY
13
1 of 1
7/30/20099:49 PM
I~ ~
13 of 25
~ ~I
IHomel
Q:U!21~.l! 10111213
16 17 18 19202122
c. DISASSEMBLY-MAIN BODY
PART NAME
in disassembling the main body assembly. Parts to be discarded and replaced from a Master Repair Kit are marked with an asterisk (*).
PART NAMe:
5 5
11A lB
2
3
6
6
6 6
7
4 6
7 8 9
5
9
9
10
11
9
9 9 9
12
13
14 15
16
17 18
10
11
11
19 12 20 14 21 22 14 23
13
Dashpot Assembly Dashpot Lockwasher Clamp Ring Retainer Screw and Lockwasher (4) Clamp (4) Clamp Ring Clamp Ring Gasket * Fuel Bowl Fuel Bowl Gasket * Fuel Inlet Seat Retainer Screw * Fuel Inlet Seat Retainer Screw Gasket * Fuel Inlet Seat Gasket * Float Shaft Retainer * Float Shaft * Fuel Inlet Needle Assembly * Float and Lever Assembly Fuel Inlet Valve Seat * Economizer Body Cover Screw and Lockwasher (4) Economizer Body Cover Economizer Diaphragm and Stem Assembly * Economizer Body Cover Gasket * Main Well and Economizer Body Screw and Lockwasher (5) Main Well and Economizer Body Pump Return Spring Main Jet
15 15 16 16
24 25 26 27
16 28 17 29 17 30 18 31 18 32 18 33
19 34 20 35 21 36
22 37 23 38 23 39
23 40
24 25 25 26
41 42 43
44
45 26 46 47
Pump Inlet Check Valve Retainer Pump Discharge Valve Retainer Pump Discharge Valve Weight Pump Discharge Valve Ball Pump Inlet Valve Ball Spacer Gasket Pump Diaphragm and Rod Assembly'" Pump Rod Sleeve Retainer Ball Pump Rod Sleeve Pump Spring Pump Operating Lever Retainer Pump Operating Lever Choke Bracket Screw and Lockwasher Distribution Pin Choke Plate Screw Choke Plate Screw and Lockwasher Choke Plate Choke Shaft Retainer Pin Choke Shaft and Lever Assembly Choke Bracket Pump Discharge Nozzle Screw Pump Discharge Nozzle Screw Gasket Pump Discharge Nozzle Pump Discharge Nozzle Gasket
Figure 6. Removing Clamp Ring Retainer Screws Figure 5. Removing Dashpot Assembly (1) If the carburetor being disassembled is for an automatic transmission engine, remove dashpot assembly and dashpot lockwasher.
(2) Remove the fuel bowl by removing the four clamp ring retainer screws and lockwashers, and clamps. Lift the clamp ring off the fuel bowl. Remove and discard the fuel bowl gasket and the paper clamp ring gasket
~~~
10fl
7/30/20099:50 PM
MCarbHollIHC53E322B page 14 of 25
I~ ~
14 of 25
~ ~I
IHomel
1: Q21 6.!! 10 1112 13 14
16 17 18 19 20
23
(5) Remove the float shaft retainer and separate the float and lever assembly from the fuel valve assembly by sliding out the float shaft. Discard all parts except the float and lever assembly.
Agure 7. Removing Fuel Inlet Seat Retainer Screw
(3) Using Snap-On Tool No. NfC-128, remove the fuel inlet seat retainer screw. Discard the retainer screw and gasket.
Figure 10. Removing Economizer Body Cover
(6) Remove the three economizer body cover screws and lockwashers. (7) Lift the economizer assembly out of the main body and discard the gasket.
Rgure 8. Aoat and Fuel Inlet Valve Assembly
(4) Lift out the float and fuel inlet assembly and discard the gasket.
"JtL
II'oIL~f
"419
Rgure 11. Removing Economizer Body

FLO"y
~HAr~ ~t'AINER U
R!!''';J4
Rgure 9. Float and Fuel Inlet Valve Separated
(8) Separate the economizer body cover from the economizer diaphragm and stem assembly. Discard the economizer diaphragm and stem assembly.
~8~
1 of!
7/30/2009 9:50 PM
I~ ~
15 of 25
~ ~I
IHomel
!H!.7 . ~ 10 1112 13 14 15 16 17 18 19 20
23
(11) Using Snap-On Tool No. TMC-36, remove the main jet from the main well and economizer body. Discard the main jet.
Figure 12. Removing Main Well and

Economizer Body Screws
(9) Remove the five main well and economizer body screws and lockwashers. (Place a thumb against the main well and economizer body to retain it in position until those screws and lockwashers have been removed.) Lift out the main well and economizer body.
Figure 15. Removing Pump Valve Retainers
(12) Remove the pump inlet check valve retainer and the pump discharge valve retainer.
Figure 13. Removing Pump Retum
(10) Remove the pump return spring which bears against the metal disk of the accelerating pump pIston.
Figure 16. Removing Pump Inlet and Discharge Valve

Balls and Weight
(13) Invert the main well and economizer body and allow the pump inlet check valve ball, pump dischar~lve weight, and pump discharge valve ball to drop out. Discard the two steel balls.
I" ,...,..,
Figure 17. Removing Accelerating Pump Assembly Figure 14. Removing Main Jet
(14) Slide the accelerating pump assembly out ofthe main body. Remove and discard the spacer gasket.
~[3~
1 of!
7/30/20099:51 PM
MCarbHoillHC53E322B - page 16 of 25
I~ ~
16 of 25
1 IHomeI
12 13 14 15 16
18 19 20 21
23
CAUTION
Care must be taken when removing the accelerating pump assembly as the pump rod sleeve is under considerable spring tel\Slon. The assembly must be pulled straight out and not rotated during removal.
. ,ii<~ ..)::1~!;--~
(18) Slide the pump operating lever off the stud.
_,~~\st
"
Figure 21. Removing Choke Bracket Screw

(>
I ;,.;:.
Figvr" la. Remov illll P\JIl1f' Rod SIAIWII! ~I!IMrne-r Boll
(19) Remove the choke bracket screw and

lockwasher.
(15) Press the pump rod sleeve toward the pump diaphragm, compressing the pump spring; and allow the pump rod sleeve retainer ball to drop out (rotate the sleeve if the ball sticks in place). Discard the ball. (16) Slide the pump rod sleeve and pump spring off the pump diaphragm rod. Discard the pump diaphragm and rod assembly.
()l'iolklBUilON PIN
+-
BRA,i':;JU
... JI
Figure 22. Removing Distribution Pin
Figure 19. Rem;)virlg PllIIF Operating LI\Vf!f" Retoi.... cr
(17) Using the thinbladed screwdriver, pry the pump operating lever retainer off the pump operating lever stud. Discard the retainer.
(20) Rotate the choke plate past the full open position until it is nearly inverted. Place the distribution pin in a section of brass tubing with the end of the tube bearing against the choke shaft. Using a flat tip punch or a piece of 118 inch drill rod, drive the pin flush with the choke shaft. Then, using a smaller diameter punch or drill rod, drive the pin out of the choke shaft. Refer to "Special Tools and Improvised Tools" on page 10 for complete information on the improvised tools.
NOT
In the illustration (Figure 22), a section of the upper portion of the brass tubing is shown cutaway for the purpose of clarity. Do not cut out this section of tubing.
Figure 20. Removing Pump Operating Lever
[3
1 of 1
7/30/20099:51 PM
I..
17 of 25
1 IHomel
1.6. f!
10 l i 12 13 14
18192021
CAUTION
Care is to be taken when removing the dis tribution pin to prevent damaging the choke shaft and poppet valve.
Figure 25. Removing Choke Shaft
(23) Remove the choke shaft and lever assembly and the choke bracket.
Figure 23. Removing Choke Plate
(21) Remove and discard the choke plate screws ld locwasher and slide the choke plate out of the loke shaft.
NOT
lfthe tip of the choke plate screw has been
flared out excessively by staking, it is ad
visable to file off the flared-out portion to
avoid damaging the threads in ilie choke
when removing the screw. Care is to be taken
while filing the screw tip to avoid damaging
the carburetor bore, choke shaft, or other
components.
{.,--so";
Figure 26. Removing Pump Discharge Nozzle Screw
(24) Remove the pump discharge nozzle screw and hft out the pump discharge nozzle. Discard the two gaskets.
NOT
In some versions of this carburetor model the fuel bowl contains an externally adjusted needle for regulating fuel flow through the main jet. Replacements for this main adjusting needle assembly will be found in the Master Repair Kit. "
! ,~
""~'i' ~f'
... :-- ,\ f " ~." I
"~,"r""'~
. ir . ( .' ....
~'ji'j. ;.....r
.'
-- ,.. !... ~
~<
figure 74. RelTlOving Cho~e S,~h Retainer Pi"

U~tl;l
>
(22) Using a small flat-tip punch, drive the hoke shaft retainer pin out of the main bo dv.
Figure 27. Disassembly" Throttle Body Assembly
.~.
10fl
7/3012009 9:52 PM
I..
18 of 25
..1
IHOfII8I
fll0 1112 13 14 15 16 17 18 19 20 21 22
This completes the disassembly of the main body assembly. Do not attempt to remove any of the pressed-in passage plugs, air bleed plugs, or the main nome in the main body, D. DlSASSEMBLY-THROITLEBODY
ASSEMBLY
The following list contains all parts removed in disassembling the throttle body assembly. Parts to be discarded and replacement made from a Master Repair Kit are marked with an asterisk (*).
"1';1;
((L
I{
I
-.: ....
I
(;]: .? tll ., ,''''.,p. "'. "
' \..
flii(jtH.t
~
'."'.
"
Figure 29. Pump Link and Cotter Pin
REFER TO
FIG. NO.
ORDER OF REMOVAl
PART NAME
.. n
~ntP"lf!i
?---
.
~:
28 28
29 29
1 2 3
4
30
30 30 31 31
I iJmo Link* Screw and TJ ITottle Plate

I
Lockwasher (2)* Throttle Plate Throttle Shaft Dashpot Lever Screw Dashoot Lever Soring Dashpot Lever
,
Idle Adjusting Needle*

Idle Adiusting Needle Soring
Pump Link Cotter Pin*
~
.
" ", r":'~:r'.';,~~r~~~N;: _~I' ~~~ .

: I
l1!110nIL f ... ,
"r '
.':
.
-.".
~. ~33\~.~~
6
7
figure 30, Tl,roHI.. ShelF! n"d Plate Removud
8 9
10
(4) Slide the throttle shaft and lever assembly out of the throttle body.
DASHPOTLE~
31
.... ,",
~
D.oSHfCJ L[V[~ ~tln,(, . \
"",."J
"~~
tJPOT U'If"
5e11....,
.___'" ,.,~!r:pf ~r.)~\\LH"':;

........... ~
..;,JJJjJ
,m;:>u
...,-./'
DVADUII-.O
Nf:H~!;:-
Figure 31, Rerroving Dashpot Lever Screw
:PRI...,,:::
Figure 28, Rerroving Idle Adjusting Needle
(1) Remove the idle adjusting needle and spring. Discard the needle.
(5) On carburetors for the automatic trans mission engine, remove the dashpot lever screw, spring, analever.
(2) Remove and discard the pump link cotter pin and pump link. (3) Scribe the throttle plate along one side of the throttle shaft to facilitate proper alignment during reassembly. Remove and discard the two throttle plate screws and lockwashers. Lift out the throttle plate .
This concludes the disassembly of the Car

buretor Model 1904.
5. CLEANING AND INSPECTION A.CLEANING ( 1) All castings and metal parts except the dashpot assembly are to be soaked in a cleaning
13.
1 of!
7/30/20099:52 PM
http://www.oldcarmanualproject.com/manualslCarbslHolley/H...
I~ ~
19 of 25
....,
IHomal
12 13 14 15 16 17 18 19 20
solution to loosen the accumulated foreign matter. Laquer thinner or denatured alcohol may be used if a commercial carburetor cleaning solvent IS not available. Place the parts to be cleaned in a wire basket suspended in the solution. After the parts have soaked sufficiently to loosen the foreign deposits, they should be rinsed in hot water to remove all traces ofthe cleaning solution. All remaining foreigll deposits should be scrubbed away with a stiff bristle brush while the parts are being rinsed.
tion may be made by directing compressed air through the passages. (Refer to the "Operation" section, begirming on page 2, for locations of pass ages in the castings). (2) CHOKE SHAFT AND THROTTLE SHAFT Check the shafts for distortion, stripped threads, or loose levers. If irregularities are found, the shaft should be discarded. Also examine the swivel assembly on the choke lever for stripped threads. If damage is found or the swivel is no longer securely riveted, the choke shaft and lever assembly must be replaced. (3) FUEL BOWL The fuel bowl must be replaced ifthe edges are chipped or if cracks are found anywhere in the bowl. In the plastic fuel bowls containing the adjustable jet, the adjusting needle body must be checked for signs ofleaking or for other evidence of damage or distortion. (4) FLOAT AND LEVER ASSEMBLY Replace the float and lever assembly ifthe float leaks, or ifthe assembly is corroded or damaged. Shake the float to determine if fuel has leaked into it. (5) THROTTLE AND CHOKE PLATES Discard the plates if distortion, nicked edges, corrosion, or damage to the protective plating is found. Ch.eck to insure that the poppet valve in the choke plate IS clean and operates properly. (6) SPRINGS AND RETAINERS Distorted or damaged springs and retainers must be replaced. (7) SCREWS, LOCKWASHERS, AND Screws, lockwashers, and nuts must be replaced if stripped threads, distortion or other damage is found.
6. REASSEMBLY
(2) Soak each casting and part briefly in clean gasoline and dry them with compressed air. Direct the compressed air through ail passages in the castings and through all openin~,' jets, and tubes. As the neoprene i:liaphragm oftne dashpot assembly is deteriorated by most cleaning solvents, the exterior of the dashpot assembly should be wiped clean with a rag moistened with gasoline. Do not use compressed air on this assembly as the diaphragm and the synthetic rubber bellows seai may be distorted or ruptured. CAUTION Attempts to clean passages with a wire, drill, or similar object may distort those passages and adversely affect carburetor performance. Use of a buffmg wheel, wire brush, or other abrasive means to remove surface deposits may damage the part and also remove the protective plating, exposing the part to corrosion. NOTE As gaskets, neoprene diaphragms, and felt seals are deteriorated by most solvents, those items should never be exposed to cleaning fluids. Never re-use old gaskets neoprene diaphragms, or felt seals when rebuIlding the carburetor.
B. INSPECTION
(1) MAJOR CASTINGS All major castings are to be examined for cracks, stripped threads, or damaged gasket mating surfaces and discarded if damage is found. Check the venturi bore in the main body casting for si~s of nicks, scratches, or other imperfections. CalIbration of the carburetor may be affected by even a slight irregularity in the venturi. Examine the main discharge nozzle in the venturi and other passages in the castings for signs of damage or obstruction. The check for obstruc
A. REASSEMBLY-THROTTLE BODY (1) Slide the throttle shaft and lever assembly into position in the throttle body. Referring the marks scribed on the plate during disassembly, set the plate in place on the throttle shaft. and hold the throttle body up to the light. If no excessive amoUllt of light shows between the edge
~~
..
1 of!
7/30/2009 9:52 PM
I~ ~
20 of 25
~ ~I
IHome I
10 1112 13 14 15 16 17 18 19 20 21 22
Tll!;onl r
~I,.. ~r
against the edge of its recess in its proper operating position after a small amount of rotation.
NOTE
In the List No. 763 and 831 Carburetors, however, the pump discharge nozzle should be held in a counter-clockwise position against the limits of its rotational travel as the nozzle screw is tightened.
H~-4<
NO':' pesl 1101"

OF ~'\'F' H; F'l(,=
' ' !;"'.
Figure 32. Installing Throttle Plate
of the throttle plate and the throttle bore, and if the throttle plate moves freely throughout its range of travel, throttle plate alignment is satisfactory. Hold the throttle plate in the closed position and tighten the throttle plate screws. (2) Install the new pump link in the throttle lever with the double bend of the link uppermost. Secure the pump link in place with one of the new pump link cotter pins. (The two holes in the throttle permit adjustments to compensate for climatic conditions; place the pump link in the hole nearest the throttle shaft for normal climatic conditions, or use the outer hole for continuous extreme cold weather operation.) (3) Install the new idle adjusting needle with its spring. Turn the needle down gently with the fingers until it seats, then back it off one full turn. Take care not to force the needle down on its seat. This will groove the tip of the needle and make it impossible to accurately adjust the idle mixture. (4) On carburetor for automatic transmission engines, install the dashpot lever, spring, and screw.
B. REASSEMBLY-MAIN BODY
(1) Place a new gasket on both sides of the pump discharge nozzle, then insert the pump discharge nozzle screw into the channeled side of the nozzle. (The pump discharge nozzle screw may be identified by the hole drilled vertically from its tip to a point shortly below the head of the screw, where it joins a short horizontal drilled passage terminating in a groove in the side of the screw.) Install the pump discharge nozzle in the recess at the top of the venturi in the main body. Allow the pump discharge nozzle to rotate to the limits of its travel in a clockwise direction as the nozzle screw is tightened. The nozzle will stop
(2) Position the choke bracket on the boss on the main body. Slide the choke shaft and lever assembly into the main body and secure it in place by driving the choke shaft retainer pin into the small vertical hole in the top of the choke shaft boss. (3) Rotate the choke lever until the choke lever swivel is below the choke shaft. Insert the choke plate into the slot in choke shaft with the stem and spring of the poppet valve extending upward.
CAUTION
Take care not to damage the tip of the main nozzle while installing the choke plate. (4) Center the choke plate to avoid damaging the venturi then close the choke plate by rotating the choke lever in a counter-clockwise direction. Install the choke plate screws, fitting the screw with the attached lockwasher in the hole nearest the choke lever. Turn the screws down snugly but not tightly. Rotate the choke lever until the choke plate is nearly inverted and the poppet valve stem and spring extend downward. Align the distribution pin hole in the choke shaft with the corresponding hole in the choke plate. Brace the choke shaft from beneath and drive the distribution pin into position. Install the distribution pin so the clearance betweei1e tip of the pin and the venturi wall is equal on both sides
1
.t
1..1
('11
","
NOTE
The List No. 763 and 831 Carburetors use a hex-head screw on the side of the choke shaft nearest the fuel bowl and pump discharge nozzle. A stem extends above the hex-head ofthe screw to facilitate proper fuel distribution in C.O.E. installations. A shakeproof external tooth lockwasher is used to retain the screw. The regular choke plate screw continues in use as the other plate screw.
~ ~ ~
10fl
7/30/20099:53 PM
,..
21 of 25
~ ~I
IHome'
202122
(5) Check the choke plate for binding by moving the choke lever through the extent of its travel. If it moves freely, tighten the choke plate screws while holding the choke plate in the fully closed position. Stake the screws (on carburetor models having choke plate screws without lockwashers) using any approved staking tool. If an impact type staking tool, such as a punch, is used, each screw head should be braced with a solid object to prevent bending the choke shaft. Take care not to nick or mar the venturi or choke plate with the staking tool. (6) Install the choke bracket screw and lock
washer.
(7) Place the pump operating lever on the stud in the maIO body and secure it by fitting the new pump operating lever retainer in the groove at the end of tlie shaft.
freely in their chambers, then install the pump

discharge valve weight and the two retainers.
NOTE
It is extremely important that these parts are correctly installed or carburetor performance will be adversely affected. (10) Using Snap-On Tool No. TMC-36, install the new main jet in the main well and economizer body.
(11) Place the new main well and economizer

body spacer gasket in position over the accelerating
pump diaphragm.
(12) Install the pump return spring, seating the larger end of the spring in the metal disk of the accelerating pump piston.
u,.J\ .....j
~~;:i:
!:. '1.)
(8) Place the pump spring on the rod of the new pump diaphragm and rod assembly. Position the pump rod sleeve on the pump diaphragm rod with the small hole in the sleeve aligned with the center ofthe flat cutaway portion of the rod. Press the sleeve on the rod, compressing the pump spring, and drop the new pump rod sleeve retainer ball into the small hole in the pump rod sleeve. Insert the assembly into position in the main body.
L~~ ....... O,\,.tLl1{ 6~\)V
A~~MGtY
--;4
If....------I
P-,I:".
()I"C",,~,::,'
It. 4.d
vt.l.vr ~,(JG>lt
~lrMfl.tl~j"r:~.~{_.t
II.. tv.(; tAlL
Figure 34. Installing Main Wen and Economizer
Body
'J ....w ':"',f-11(;~:
)",LLIL".IH.;t)'-.~
",,+ II
,
~ f
,:'
'!
{.
:"-'-- -
1_:''''''''llf~ ~\II.;'
~>f"
;;,a, '/' -t ~".-"'t't ;'.."J
...
.,tt
ll-~.
W'
./)7.: :
.!
..... i t ' > -; ,
r.',
.... >
g
Ir . '

~~. ~
,
~
x
'tt a
, . ,...
"I. i'
,..
f i<;Jore 33. In.lell ing Pump Inlet I>"d Disaharg'" Vl,llIe Bell,
(9) Install the pump inlet check valve ball and the pump discharge valve ball in the main well and economizer body. (The pump inlet check valve ball is the larger of the two balls.) The new steel balls are to be seated by placing a thin brass rod on the top of each ball and tapping the rod very lightly three or four times with a fiber mallet, Shake the casting to insure that the balls move
(13) Align all holes in the main well and economizer spacer gasket with the corresponding holes in the accelerating pump diaphragm and the main body. Insert the five main well and economizer body screws and lockwashers in the main well and economizer body with the two long screws placed in the center top and bottom holes. Set the power valve situated at the extreme right end of the main well and economizer body into its position in the main body, then press the main well and economizer body into place against the accelerating pump diaphragm using the following procedure. Grasp the mabndy in the left hand, holding the thumb over the protruding end of the pump rod sleeve and the fmgers over the main well and economizer body. Apply pressure with thumb and fmgers to compress the pump spring and pump return spring. This pressure must be applied evenly to prevent the tension of the pump return spring from disturbing the alignment of the holes in the diaphragm, spacer gasket, and the main body. After the main well and economizer body
.l3~
1 of!
7/30/20099:1')3 PM
I~ ~
22 of 25
1 IHomeI
1213 14151617 18 19202122
is pressed into position, maintain the pressure until the five main well and economizer body screws have been started in their holes and a check is made on the alignment of the diaphragm and spacer gasket Do not tighten the screws, but tum them In as far as possible without compressing the lockwashers. Release the pump rod sleeve. This will allow the pump return spring to expand, stretching the accelerating pump diaphragm to insure full travel when the accelerating pump is operated. Then tighten the five main well and economizer body screws. (14) Insert the three economizer body cover screws and lockwashers in the economizer body cover. Place the new economizer diaphragm and stem assembly and the economizer body gasket over the screws. Insert the assembly into its position in the main body, taking care the alignment of the vacuum passage hole is not disturbed, then tighten the screws. (15) lrthe fuel inlet needle assembly has been received unassembled, it is to be assembled as follows. Fit the new fuel inlet needle spring over the fuel inlet needle pin and insert those parts into
the new fuel inlet needle. In
INlH stall the new wire fuel valve clip NFfDlf fl." .. in the groove in the fuel inlet
needle.
er screw which protrudes into the fuel bowl. Ease the float and fuel inlet valve assembly into position and secure it in place by tightening the fuel inlet seat retainer screw, using Snap-On Tool No. MCI2_S.
ij
Figure 36. Setting Float
(IS) At this point the float setting should be checked and necessary adjustments made. Invert the main body assembly, allowing the float to drop to the closed position. Using Snap-On Tool No. MC-I64, gauge the float, checking the setting on both the "touch" and "no touch" legs of the gauge. The level ofthe float may be adjusted by bending the small tab in the float lever which contacts the head of the fuel inlet needle pin. Use needle-nosed pliers for this correction and recheck the float setting after adjustments have been made. (19) Fit the new fuel bowl gasket into the recess in the rim of the fuel bowl in the main body. Place the new clamp ring gasket and clamp ring on the fuel bowl and set the fuel bowl in position on the main body. Install the four clamp ring retainers, screws, and lockwashers. Tighten the screws alternately, a half a tum at a time, until the lockwashers are compressed. The screws must be tightened alternately and not drawn too tightly to prevent setting up stresses that may result in a cracked fuel bowl.
(16) Set the fuel inlet needle

on the float lever tab, placing the
fuel valve clip under the tab to
hold the needle in place. Guide
the fuel inlet needle into the new
fuel inlet needle seat, positioning
the pivot of the float lever be tween the float lever bracket arms
on the fuel inlet needle seat. Install the new float shaft and new float shaft retainer.
SWot'\;(';
I
J1
C2
~~"'1'
I'IN
ClI.
Figure 35. Fuel Inlet Needle Assembly
NOT
The procedure for installing the plastic fuel bowls containing the adjustable jet is the same as described above except the main body is to be held in the inverted position so the float is in its fully closed position and clear of the mainjet. Install the fuel bowl with the adjusting needle backed out to the open position, taking care not to damage the tip of the needle when the bowl is set in place. (20) Install the dashpot assembly on carburetors so equipped.
CAUTION
Fuel inlet needles and seats are matched assemblies, factory tested to insure proper operation, and their component parts are not interchangeabIe. (17) Place the new fuel inlet seat retainer screw gasket on the new fuel inlet seat retainer screw and insert the screw in the fuel inlet fitting boss on the main body. Place the new fuel inlet seat gasket on the end of the fuel inlet seat retain
~ ~.
MCarbHolllHC53E322B - page 23 of 25
14 4 23 of 25
~ ~I
IHome I
13 14 15 16 17 18 192021 22
C. REASSEMBLY-MAIN BODY TO THROTTLE BODY ASSEMBLY ( I ) Insert the two throttle body screws and lockwashers into the throttle body. Settle the new throttle body to main body gasket in place over the throttle body screws and check to insure the proper alignment of the holes in the gasket with the corresponding holes in the throttle body. Set the main body in position on the throttle, body ,
invert the carburetor and tighten the two screws. Tighten the screws alternately, a little at a time, to compress the gasket evenly and eliminate the possibility of an air leak. (2) Insert the upper end of the pump link in the pump operating lever and secure it in place with the new pump link cotter pin. This completes the reassembly ofthe Carbu retor Model 1904. It is now ready for installation on the engine.
INSTALLATION
1. INSTALLATION ON THE ENGINE
Check the carburetor mating surface on the intake idle speed. Clockwise rotation of the idle adjusting manifold for signs of rust or dirt. If it is clean fit a new needle will give a leaner mixture, counterclockwise carburetor flange gasket on the manifold and install the rotat.ion a richer ~ixtur~. An e!fective settin~ may be carburetor. Tum the two carburetor mounting nuts down obta~ed b~ turnmg the Idle adjust needle m until a hand tight and connect and tighten the fuel line and the drop m engme speed results and then backing the distributor vacuum line. Then draw the mounting nuts needle off over the "high-spot" until the engine again down evenly, tightening them alternately a little at a time slows down. Setting the idle adjusting needle between until the flange gasket has been compressed and the nuts the~ two points result in a satisfactory idle mixture are tight. This method of tightening the mounting nuts ~ettmg. S?ould ~his adjustment result in an excessive will eliminate the possibility of an air leak past the flange mcrease m the Idle rpm, reset the throttle stop screw gasket. Cohnect the throttle and choke linkage, checking to. obtain th~ specified rpm and again adjust the idle the choke plate in the carburetor venturi to insure it open~llxture settmg. fully when the choke control knob is pushed in. Clean NOTE and install the air cleaner. The accelerating pump stroke can be adjusted CAUTION to compensate for seasonal or climatic changes by changing the position of the link The moving parts of the dashpot in the throttle lever. The hole in the lever assembly are not to be lubricated. Any nearest the throttle shaft is the normal setting attempt to lubricate the diaphragm rod and should be satisfactory for nearly all operating conditions. Should a richer will eventually result in the formation of sludge in the oashpot, preventing the acceleratmg pump discharge be required for proper functioning ofthe unit. extreme cold weather operation, the pump link is to be placed in the outer hole m the 2. CARBURETOR ADJUSTMENTS A. throttle lever. ADJUSTING THE IDLE B. ADJUSTING THE DASHPOT (1) All carburetor adjustments to be accurate must be made with the vehicle standing on a level surface. (I) The dashpot on carburetors for engines Start and warm up the engine. When the engine has reached its normal operating temperature, after first equipped with automatic transmissions is to be adjusted after the idle speed and mixture settings have checking to insure that the choke plate is fully open, adjust the throttle stop screw to idle the engine at the been completed. Close the throttle lever to the idle rpm specified in the current Holley Carburetor Company position. Set the dashpot adjusting screw so the Specifications Catalogue. clearance specified in the current Holley Carburetor Company Specifications Catalog is obtained between the dashpot adjusting screw and the diaphragm rod with the rod in the fully compressed position. To assure an accurate adjustment, check the choke plate (2) Set the idle adjusting needle to give the to insure it remains fully opened while setting the
highest steady manifold vacuum or, if a vacuum dashpot adjusting screw.
gauge is not available, the smoothest maximum
4 [3
1 of!
7/30/2009 9:54 PM

Cts 11-12 Service Manual Complete

Uploaded by

Copyright:

Available Formats

Cts 11-12 Service Manual Complete

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Cts 11-12 Service Manual Complete

Uploaded by

Copyright:

Available Formats

Donated by John & Susan Hansen - For Personal Use Only

MOTOR TRUCK SERVICE MANUAL

Donated by John & Susan Hansen - For Personal Use Only

CTS-11 FOR L-LINE TRUCKS

CTS-12 Supplemental Pages, for

Donated by John & Susan Hansen - For Personal Use Only

Donated by John & Susan Hansen - For Personal Use Only

L-LINE MOTOR TRUCKS

Motor Truck Division

INTERNATIONAL HARVESTER COMPANY

Donated by John & Susan Hansen - For Personal Use Only

1993-2009 International Truck Intellectual Property Company, LLC, Warrenville, IL,

Donated by John & Susan Hansen - For Personal Use Only

CHECKING LIST AND INDEX

1 thru 1 thru 1 thru I, 2 1 1 thru 1 thru 1 1 thru

CTS IZ-MARC!1 1953 (Supplemen ! p."e. for CTSI I),

PRINTED fN UNITED ST"TES OF' ""'HHHeA-.

Donated by John & Susan Hansen - For Personal Use Only

Donated by John & Susan Hansen - For Personal Use Only

L-LINE MOTOR TRUCK SERVICE MANUAL

GENERAL INFORMATION GROUP

PRINTED IN UNITED STATES OF "MERleA

Donated by John & Susan Hansen - For Personal Use Only

L-LINE MOTOR TRUCK SERVICE MANUAL

THE INTERNATIONAL HARVESTER COMPANY

Donated by John & Susan Hansen - For Personal Use Only

L-UNE MOTOR TRUCK SERVICE MANUAL

GENERAL Section Page 1

INSPECTION OF NEW TRUCKS BEFORE DELIVERY

INSTRUCTIONS TO OWNER AT TIME OF DELIVERY

6. Importance of proper clutch pedal clearance

Donated by John & Susan Hansen - For Personal Use Only

L-UNE MOTOR TRUCK SERVICE MANUAL

MOTOR TRUCK COMPLAI NT

MAIL 5 COPIES TO GENERAL OFFICE, CHICAGO MOTOR TRUCK SERVICE SECTION

SERIOUSNESS Of FAILURE IS BASED UPON THE NUMBER Of COMPLAINTS RECEIVED, REPORT , - - - - - - - - - - - - - - - - - - -

SALgS Se:RVICE: SECTION

FT. WAYNE WORKS

SPRJNGFlELO WORK'S FT, WAYNE

SERViCe: PARTs DEPT.

TOTA1. MI1.ES TO DATE 14,289

MAX, PAY1.0AD________________ MAX, PAYLOAD____~~~~~-----

TRUCK BODY SIZE

SIZE~6.-~.il'II~.u.~::::c- WHO MOUNTED BODY

Tra~1mo b ' l e ' 1

1.0CA1. OR LONG DISTANCE Distanc-filyPE OF ROADS,-,,:-.:::::-!-=...c=rWHO MAl NTAI NS

'--_ _ _ 1.ABOR_____ GRATISED

Name INVESTIGATED BY____~~~~____~~__~__- -__~-------------REMARKS_____________________

Donated by John & Susan Hansen - For Personal Use Only

L-UNE MOTOR TRUCK SERVICE MANUAL

GENERAL Section Page 3

MOTOR TRUCK COMPLAINT FORMS

material, unsatisfactory perforITlance or diffi culty of servicing our trucks.

5. State the complaint clearly on form CT-6

Donated by John & Susan Hansen - For Personal Use Only

L-UNE MOTOR TRUCK SERVICE MANUAL

MOTOR TRUCK PRODUCT REPORT

COMPLAINT SPEEDOMETER CABLE-.llB.OLEJLJmE TO CABLE RAVING

DISTRICT OFFICE~TR.lC'1'_ . - - - -... --.---.-.. ~--_ci SIGNED_.. . --.!N=A=ME=--_____

rs where assi.ldllce is necessary or where an acknowledg.

MAX, PAY1.0AD____________ MAX, PAYLOAD~~~~~-----

Name INVESTIGATED BY~~~~~~~- -~-------------REMARKS___________________