Poly-Phase Circuits

Poly-phase circuits
Advantages of 3-phase system

• Thinner conductors can be used to transmit the same kVA at the same voltage,
which reduces the amount of copper required (typically about 25% less) and in
turn reduces construction and maintenance costs.
• The lighter lines are easier to install, and the supporting structures can be less
massive and farther apart.
• Three-phase equipment and motors have preferred running and starting
characteristics compared to single-phase systems because of a more even flow of
power to the transducer than can be delivered with a single-phase supply.
• In general, most larger motors are three phase because they are essentially self-
starting and do not require a special design or additional starting circuitry.
• The number of phase voltages that can be produced by a polyphaser
generator is not limited to three. Any number of phases can be
obtained by spacing the windings for each phase at the proper
angular position around the stator.
Balanced 3-phase system
• The source has three terminals (not
counting a neutral or ground
connection), and voltmeter
measurements will show that sinusoidal
voltages of equal amplitude are present
between any two terminals.
• However, these voltages are not in
phase; each of the three voltages is 120°
out of phase with each of the other two,
the sign of the phase angle depending
on the sense of the voltages
Connections
• In a 3-phase system, two types of connections are possible:
• Star Connection
• Delta Connection
3-Phase Star (Y)- Connection
• Three-phase sources have three
terminals, called the line terminals, and
they may or may not have a fourth
terminal, the neutral connection.
• We will consider only balanced three-
phase sources, which may be defined as
having
• These three voltages, each existing between one line and the neutral,
are called phase voltages. If we arbitrarily choose Van as the
reference, or define
• where we will consistently use Vp to represent the rms amplitude of

any of the phase voltages, then the definition of the three-phase
source is indicated as
• This sequence is called as Positive Phase sequence.

• If the sequence is considered as
• This considered as Negative phase sequence.

Line-to-Line Voltages
• the line-to-line voltages (often
simply called the line voltages) is
the voltage between two line
terminals.
• From the Phasor diagram these can
be calculated as:
• sum of these three line voltages is

also zero, in case of the balanced
voltages
• If the rms amplitude of any of the line voltages is denoted by VL, then
one of the important characteristics of the Y-connected three-phase
source may be expressed as
• Note that with positive phase sequence, Van leads Vbn and Vbn leads
Vcn, in each case by 120◦, and also that Vab leads Vbc and Vbc leads Vca
, again by 120◦.
• The statement is true for negative phase sequence if “lags’’ is
substituted for “leads.’’
Three phase Y-Y Connection
• The load is represented by an
impedance Zp between each line
and the neutral. The three line
currents are calculated as:
Thus, the neutral

carries no current if the
source and load are
both balanced.
THE DELTA (∆) CONNECTION
• This type of configuration is very common, and does not possess a
neutral connection
If the load is Delta-connected, then the phase
voltage and the line voltage are Same, but the line
current is larger than the phase current by a factor
of √3; with a Y-connected load, however, the
phase current and the line current refer to the
same current, and the line voltage is greater than
the phase voltage by a factor of √3.
Watt-Meter
• In electrical systems, the power is measured by using a device called Watt-meter
• a wattmeter that contains two separate coils. One of these coils is made of heavy
wire, having a very low resistance, and is called the current coil
• the second coil is composed of a much greater number of turns of fine wire, with
relatively high resistance, and is termed the potential coil, or voltage coil.
• The torque applied to the moving system and the pointer is proportional to the
instantaneous product of the currents flowing in the two coils.
• The mechanical inertia of the moving system, however, causes a deflection that is
proportional to the average value of this torque.
• The wattmeter is used by
connecting it into a network in
such a way that the current flowing
in the current coil is the current
flowing into the network and the
voltage across the potential coil is
the voltage across the two
terminals of the network.
• The current in the potential coil is
thus the input voltage divided by
the resistance of the potential coil.

Poly-Phase Circuits

Uploaded by

Copyright:

Available Formats

Poly-Phase Circuits

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Poly-Phase Circuits

Uploaded by

Copyright:

Available Formats

Poly-phase circuits

Advantages of 3-phase system

• where we will consistently use Vp to represent the rms amplitude of

• This sequence is called as Positive Phase sequence.

• This considered as Negative phase sequence.

• sum of these three line voltages is

Thus, the neutral

You might also like