Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd Logo
Upload

Welcome to Scribd!

  • 58 views

    Mogas Valves Om Manual

    Uploaded by

    Thairanil Abduljaleel
    This document provides instructions for replacing the stem packing on a MOGAS Industries metal seated ball valve. It involves loosening the packing gland nuts, removing the used packing rings, cleaning the packing box, installing new packing rings in the correct configuration, reassembling the gland flange components, and retightening the nuts while cycling the valve to ensure proper repacking. The process helps maintain the valve seal and prevent stem leaks.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Mogas Valves Om Manual

    Uploaded by

    Thairanil Abduljaleel
    58 views6 pages
    This document provides instructions for replacing the stem packing on a MOGAS Industries metal seated ball valve. It involves loosening the packing gland nuts, removing the used packing rings, cleaning the packing box, installing new packing rings in the correct configuration, reassembling the gland flange components, and retightening the nuts while cycling the valve to ensure proper repacking. The process helps maintain the valve seal and prevent stem leaks.

    Original Title

    Mogas valves om manual

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    This document provides instructions for replacing the stem packing on a MOGAS Industries metal seated ball valve. It involves loosening the packing gland nuts, removing the used packing rings, cleaning the packing box, installing new packing rings in the correct configuration, reassembling the gland flange components, and retightening the nuts while cycling the valve to ensure proper repacking. The process helps maintain the valve seal and prevent stem leaks.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    58 views6 pages

    Mogas Valves Om Manual

    Uploaded by

    Thairanil Abduljaleel
    This document provides instructions for replacing the stem packing on a MOGAS Industries metal seated ball valve. It involves loosening the packing gland nuts, removing the used packing rings, cleaning the packing box, installing new packing rings in the correct configuration, reassembling the gland flange components, and retightening the nuts while cycling the valve to ensure proper repacking. The process helps maintain the valve seal and prevent stem leaks.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    You are on page 1of 6

    Replacing

    Stem Packing
    for the MOGAS
    Improved RSVP Metal Seated Ball Valve

    SRD-1004 © Copyright 2006 MOGAS Industries, Inc. 281.449.0291 www.mogas.com 


    replacing stem packing

    ! WARNING!
    DO NOT perform this task under line pressure. Make sure the line is not under pressure.

    Note:
    Refer to exploded view of valve (page 6) to identify
    parts and reference numbers.

    1 Locate packing gland nuts (15). Turn nuts counter


    clockwise to loosen and remove packing gland nuts.
    15

    2 Locate and slide upward the gland flange (07A), live-


    loading springs (07C) and gland thruster (07B).
    12

    07A

    3 Remove studs (12) — this allows access to the used


    packing rings.

    07C

    07B

    4 Using a small pick, carefully remove the packing


    rings (09A).

    The solid metal anti-extrusion ring (09C) at the bottom


    of the packing box should not be removed.
    09A

    SRD-1004 © Copyright 2006 MOGAS Industries, Inc. 281.449.0291 www.mogas.com 


    replacing stem packing
    5 Use an air hose to clean debris from packing box
    before installing new packing rings.

    Note:
    Always wear a face shield or mono-goggles to protect
    eyes from flying debris.

    6 The new packing ring set will contain 2 anti-extrusion Skive Cut
    09B
    rings (09B) and 2 or 3 packing rings (09A). (Refer to the
    table below to verify the correct packing ring quantity.) 09A Skive Cut
    Skive Cut
    09A
    These rings are supplied with a skive cut. Assemble
    the rings as shown. Position the skive cut on each ring 09A Skive Cut
    opposite, alternating the adjacent skive cut rings. All Skive Cut
    rings should fit into the packing box. 09B

    Quantity of Valve Packing Rings


    Valve Bore 1500# 3100# 4500#
    0.63 inches 2 3 3
    1.00 inches 3 3 3
    1.3 inches 3 3 —
    1.5 inches 3 — —

    7 Carefully bend each fragile ring, spiraling it around the


    stem (05), then insert and evenly press into the packing
    box.

    DO NOT try to open ring wide enough to install the


    ring from the front. Instead, snake it around the stem,
    minimizing how wide it must be opened. Forcing the
    ring onto the stem frontally usually causes the ring to
    break.

    8 Use gland thruster (07B) as tool to slide each ring into


    packing box. Continue this process until all rings are
    positioned correctly in the packing box.

    07B

    SRD-1004 © Copyright 2006 MOGAS Industries, Inc. 281.449.0291 www.mogas.com 


    replacing stem packing
    9 Slide the gland thruster (07B) over the packing box.

    07B

    10 Position the live load springs (07C) on top of the gland


    thruster (07B).

    07C

    07B

    11 Re-install the studs (12).

    12

    12 Re-install the gland flange (07A) over the packing


    bolting.

    07A

    SRD-1004 © Copyright 2006 MOGAS Industries, Inc. 281.449.0291 www.mogas.com 


    replacing stem packing
    13 Install and tighten nuts (15) evenly by alternating sides
    when tightening. Make sure the gland flange (07A)
    does not bind or drag on the stem (05). 05
    15
    The following table shows the proper torque required.
    07A
    Recommended Packing Gland Stud Torque (ft. lbs.)
    Valve Bore 1500# 3100# 4500#
    0.63 inches 4 11 16
    1.00 inches 7 15 25
    1.3 inches 8 17 —
    1.5 inches 9 — —

    14 Cycle valve a couple times to ensure proper


    re-packing.

    Verify torque as shown in the table above.

    SRD-1004 © Copyright 2006 MOGAS Industries, Inc. 281.449.0291 www.mogas.com 


    Valve Part number reference
    (36) Hex Head (36) Hex Head Bolt
    Bolt (qty. 2) (17C) Washer
    (13) Handle Adaptor
    (35) Set Screws (qty. 2) (53A)
    Hand Grip
    (53) Hand Lever

    (18) Bolt
    (17A) Washer, Tabbed
    (17B) Washer
    (06) Key (qty. 2)
    (17) Pin
    (16) Stem Bushing

    (05) Stem

    (15) Nut, Std. Hex (qty. 4)

    (07A) Gland Flange

    (07C) Spring Disc, Live Load (qty. 2)


    (07B) Thruster, Gland Flange
    (42) (09B) Ring, Anti-Extrusion
    Mechanical
    Precision (09A) Ring, Stem Packing (qty. 2 or 3)
    Stop (MPS) (09B) Ring, Anti-Extrusion
    (09C) Ring, Anti-Extrusion, Metal

    (02) Body

    (12) Stud (qty. 4)

    (89) Valve Tag

    Note: Replacing stem packing is


    (84) the only field repair recommended.
    Contraction For all other repairs, contact
    Ring MOGAS Service Dept.

    (01B) Seat Ring


    (01A) Ball
    (01D) Seat Ring Pusher
    (01C) Spring Disc
    (29) Transition Sleeve
    (28) Retaining Ring
    (84) Contraction Ring

    SRD-1004 © Copyright 2006 MOGAS Industries, Inc. 281.449.0291 www.mogas.com 

    You might also like