SERVICE MANUAL

L213 / L215 / L218 / L220

L223 / L225 / L230
200 Series Skid Steer Loader

C227 / C232 / C238

200 Series Compact Track Loader

Part number 84423865

1st edition English
July 2011
Printed in U.S.A.
Copyright © 2011 CNH America LLC. All Rights Reserved. New Holland is a registered trademark of CNH America LLC.
Racine Wisconsin 53404 U.S.A.
 Contents

INTRODUCTION
HYDRAULIC, PNEUMATIC, ELECTRICAL, ELECTRONIC SYSTEMS A
PRIMARY HYDRAULIC POWER SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A.10.A
SECONDARY HYDRAULIC POWER SYSTEM. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A.12.A
HYDRAULIC COMMAND SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A.14.A
HIGH-FLOW HYDRAULIC POWER SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A.16.A
ELECTRICAL POWER SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A.30.A
LIGHTING SYSTEM. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A.40.A
ELECTRONIC SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A.50.A
FAULT CODES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A.50.A

ENGINE AND PTO IN ................................................................... B

ENGINE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B.10.A
FUEL AND INJECTION SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B.20.A
AIR INTAKE SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B.30.A
ENGINE COOLANT SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B.50.A
STARTING SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B.80.A

TRANSMISSION, DRIVE AND PTO OUT ........................................ C

TRANSMISSION Hydrostatic. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C.20.F

AXLES, BRAKES AND STEERING................................................. D

Final drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D.15.A
Final drive Hydraulic drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D.15.C

STEERING Mechanical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D.20.B

PARKING BRAKE Hydraulic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D.32.C

WHEELS AND TRACKS Tracks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D.50.B

WHEELS AND TRACKS Wheels. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D.50.C

FRAME AND CAB ........................................................................ E

FRAME Primary frame . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E.10.B

SHIELD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E.20.A

84423865 25/07/2011
 USER CONTROLS AND SEAT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E.32.A
USER CONTROLS AND SEAT Operator seat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E.32.C

USER PLATFORM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E.34.A

ENVIRONMENT CONTROL Heating system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E.40.B

ENVIRONMENT CONTROL Air-conditioning system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E.40.C

SAFETY SECURITY ACCESSORIES Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E.50.B

FRAME POSITIONING ................................................................. F

STABILISING Ballasting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F.20.B

TOOL POSITIONING .................................................................... G

LIFTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G.10.A
TILTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G.20.A
LEVELLING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G.30.A
SECONDARY FUNCTIONS Hydraulic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G.90.C

HITCH AND WORKING TOOL ....................................................... H

BOOM Lift . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . H.20.B
ARM TOOL ATTACHMENT Tilt. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . H.30.C
SINGLE ARM Lift . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . H.40.B
SINGLE ARM TOOL ATTACHMENT Tilt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . H.50.C

EXCAVATING AND LANDSCAPING ............................................... J

DIGGING Non-articulated digging tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . J.20.B

CARRYING Unarticulated tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . J.50.B

COUPLING Mechanical coupling. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . J.80.B

COUPLING Hydraulic coupling. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . J.80.C

84423865 25/07/2011
84423865 25/07/2011
INTRODUCTION

84423865 25/07/2011
1
 Contents

INTRODUCTION

Foreword - Ecology and the environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Safety rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2 - Series

Safety rules - Personal safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Safety rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Basic instructions - How To Use and Navigate Through This Manual . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Basic instructions - Important notice regarding equipment servicing . . . . . . . . . . . . . . . . . . . . . . . . . 12
Basic instructions - Shop and Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Torque - Minimum tightening torques for normal assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
2 - Series

Torque - Standard torque data for hydraulics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

General specification - Biodiesel Fuels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
General specification - General Welding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

84423865 25/07/2011
2
 INTRODUCTION

Foreword - Ecology and the environment

Soil, air, and water are vital factors of agriculture and life in general. When legislation does not yet rule the treatment
of some of the substances which are required by advanced technology, sound judgement should govern the use and
disposal of products of a chemical and petrochemical nature.
NOTICE: The following are recommendations which may be of assistance:

• Become acquainted with and ensure that you understand the relative legislation applicable to your country.
• Where no legislation exists, obtain information from suppliers of oils, filters, batteries, fuels, antifreeze, cleaning
agents, etc., with regard to their effect on man and nature and how to safely store, use and dispose of these
substances.
• Agricultural consultants will, in many cases, be able to help you as well.

HELPFUL HINTS
• Avoid filling tanks using cans or inappropriate pressurized fuel delivery systems which may cause considerable
spillage.
• In general, avoid skin contact with all fuels, oils, acids, solvents, etc. Most of them contain substances which
may be harmful to your health.
• Modern oils contain additives. Do not burn contaminated fuels and or waste oils in ordinary heating systems.
• Avoid spillage when draining off used engine coolant mixtures, engine, gearbox and hydraulic oils, brake fluids,
etc. Do not mix drained brake fluids or fuels with lubricants. Store them safely until they can be disposed of in
a proper way to comply with local legislation and available resources.
• Modern coolant mixtures, i.e. antifreeze and other additives, should be replaced every two years. They should
not be allowed to get into the soil but should be collected and disposed of properly.
• Do not open the air-conditioning system yourself. It contains gases which should not be released into the at-
mosphere. Your NEW HOLLAND CONSTRUCTION dealer or air conditioning specialist has a special extractor
for this purpose and will have to recharge the system properly.
• Repair any leaks or defects in the engine cooling or hydraulic system immediately.
• Do not increase the pressure in a pressurized circuit as this may lead to a component failure.
• Protect hoses during welding as penetrating weld splatter may burn a hole or weaken them, allowing the loss of
oils, coolant, etc.

84423865 25/07/2011
3
 INTRODUCTION

Safety rules
2 - Series

Personal safety

This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all
safety messages that follow this symbol to avoid possible death or injury.

Throughout this manual and on machine decals, you will find the signal words DANGER, WARNING, and CAUTION
followed by special instructions. These precautions are intended for the personal safety of you and those working
with you.

Read and understand all the safety messages in this manual before you operate or service the machine.

DANGER indicates a hazardous situation which, if not avoided, will result in death or serious injury. The
color associated with DANGER is RED.

WARNING indicates a hazardous situation which, if not avoided, could result in death or serious injury.
The color associated with WARNING is ORANGE.

CAUTION, used with the safety alert symbol, indicates a hazardous situation which, if not avoided, could result
in minor or moderate injury. The color associated with CAUTION is YELLOW.

FAILURE TO FOLLOW DANGER, WARNING, AND CAUTION MESSAGES COULD RESULT

IN DEATH OR SERIOUS INJURY.

Machine safety
NOTICE: Notice indicates a situation which, if not avoided, could result in machine or property damage. The color
associated with Notice is BLUE.

Throughout this manual you will find the signal word Notice followed by special instructions to prevent machine or
property damage. The word Notice is used to address practices not related to personal safety.

Information
NOTE: Note indicates additional information which clarifies steps, procedures, or other information in this manual.

Throughout this manual you will find the word Note followed by additional information about a step, procedure, or
other information in the manual. The word Note is not intended to address personal safety or property damage.

84423865 25/07/2011
4
 INTRODUCTION

Safety rules - Personal safety

Carefully study these precautions, and those included in the external attachment operators
manual, and insist that they be followed by those working with and for you.
1. Thoroughly read and understand this manual and the attachment Operator’s Manual before operating this or
any other equipment.
2. Be sure all people and pets are clear of the machine before starting. Sound the horn, if equipped, three times
before starting engine.
3. Only the operator should be on the machine when in operation. Never allow anyone to climb on to the machine
while it is in motion. If the machine is equipped with an Instructors Seat, this must only be used for training
purposes. Passengers must not be allowed to use the Instructors Seat.
4. Keep all shields in place. Never work around the machine or any of the attachments while wearing loose clothing
that might catch on moving parts.
5. Observe the following precautions whenever lubricating the machine or making adjustments.

• Disengage all clutching levers or switches.

• Lower the attachment, if equipped, to the ground or raise the attachment completely and engage
the cylinder safety locks. Completing these actions will prevent the attachment from lowering un-
expectedly.
• Engage the parking brake.
• Shut off the engine and remove the key.
• Wait for all machine movement to stop before leaving the operators platform.

6. Always keep the machine in gear while travelling downhill.

7. The machine should always be equipped with sufficient front or rear axle weight for safe operation.
8. Under some field conditions, more weight may be required at the front or rear axle for adequate stability. This
is especially important when operating in hilly conditions or/when using heavy attachments.
9. Always lower the attachment, shut off the engine, set the parking brake, engage the transmission gears, remove
the key and wait for all machine movement to stop before leaving the operators platform.
10. If the attachment or machine should become obstructed or plugged; set the parking brake, shut off the engine
and remove the key, engage the transmission gears, wait for all machine or attachment motion to come to a
stop, before leaving the operators platform to removing the obstruction or plug.
11. Never disconnect or make any adjustments to the hydraulic system unless the machine and/or the attachment
is lowered to the ground or the safety lock(s) is in the engaged position.
12. Use of the flashing lights is highly recommended when operating on a public road.
13. When transporting on a road or highway, use accessory lights and devices for adequate warning to the operators
of other vehicles. In this regard, check local government regulations. Various safety lights and devices are
available from your NEW HOLLAND CONSTRUCTION dealer.
14. Practice safety 365 days a year.
15. Keep all your equipment in safe operating condition.
16. Keep all guards and safety devices in place.
17. Always set the parking brake, shut off the engine and remove the key, engage the transmission gears, wait for all
machine or attachment motion to come to a stop, before leaving the operators platform to service the machine
and attachment.
18. Remember: A careful operator is the best insurance against an accident.
19. Extreme care should be taken in keeping hands and clothing away from moving parts.

84423865 25/07/2011
5
 INTRODUCTION

Safety rules

BT09A213 1

84423865 25/07/2011
6
 INTRODUCTION

Basic instructions - How To Use and Navigate Through This Manual

Technical Information
This manual has been produced by a new technical information system. This new system is designed to deliver
technical information electronically through Web delivery, DVD and in paper manuals. A coding system called SAP
has been developed to link the technical information to other Product Support functions, e.g., Warranty.

Technical information is written to support the maintenance and service of the functions or systems on a customer's
machine. When a customer has a concern on his machine it is usually because a function or system on his machine
is not working at all, is not working efficiently, or is not responding correctly to his commands. When you refer to
the technical information in this manual to resolve that customer's concern, you will find all the information classified
using the SAP coding, according to the functions or systems on that machine. Once you have located the technical
information for that function or system then you will find all the mechanical, electrical or hydraulic devices, compo-
nents, assemblies and sub assemblies for that function or system. You will also find all the types of information that
have been written for that function or system, the technical data (specifications), the functional data (how it works),
the diagnostic data (fault codes and troubleshooting) and the service data (remove, install adjust, etc.).

By integrating SAP coding into technical information , you will be able to search and retrieve just the right piece of
technical information you need to resolve that customer's concern on his machine. This is made possible by attaching
3 categories to each piece of technical information during the authoring process.

The first category is the Location, the second category is the Information Type and the third category is the Product:
• LOCATION - is the component or function on the machine, that the piece of technical information is going to
describe e.g. Fuel tank.
• INFORMATION TYPE - is the piece of technical information that has been written for a particular component or
function on the machine e.g. Capacity would be a type of Technical Data that would describe the amount of fuel
held by the Fuel tank.
• PRODUCT - is the model for which the piece of technical information is written.

Every piece of technical information will have those 3 categories attached to it. You will be able to use any combination
of those categories to find the right piece of technical information you need to resolve that customer's concern on his
machine.

That information could be:

• the description of how to remove the cylinder head
• a table of specifications for a hydraulic pump
• a fault code
• a troubleshooting table
• a special tool

84423865 25/07/2011
7
 INTRODUCTION

How to Use this Manual

This manual is divided into Sections. Each Section is then divided into Chapters. Contents pages are included at the
beginning of the manual, then inside every Section and inside every Chapter. An alphabetical Index is included at the
end of a Chapter. Page number references are included for every piece of technical information listed in the Chapter
Contents or Chapter Index.

Each Chapter is divided into four Information types:

• Technical Data (specifications) for all the mechanical, electrical or hydraulic devices, components and, assem-
blies.
• Functional Data (how it works) for all the mechanical, electrical or hydraulic devices, components and assem-
blies.
• Diagnostic Data (fault codes, electrical and hydraulic troubleshooting) for all the mechanical, electrical or hy-
draulic devices, components and assemblies.
• Service Data (remove disassembly, assemble, install) for all the mechanical, electrical or hydraulic devices,
components and assemblies.

Sections
Sections are grouped according to the main functions or a systems on the machine. Each Section is identified by
a letter A, B, C etc. The amount of Sections included in the manual will depend on the type and function of the
machine that the manual is written for. Each Section has a Contents page listed in alphabetic/numeric order. This
table illustrates which Sections could be included in a manual for a particular product.

SECTION
A - Hydraulic – Pneumatic – Electrical – Electronic Systems
B - Engine and PTO In
C - Transmission, Drive and PTO Out
D - Axles, Brakes and Steering
E - Frame and Cab
F - Frame Positioning
G - Tool Positioning
H - Hitch and Working Tool
J - Excavating and Landscaping
K - Crop Processing
L - Field Processing
PRODUCT
Tractors X X X X X X X X
Vehicles with working arms: backhoes, X X X X X X X X X
excavators, skid steers, .....
Combines, forage harvesters, balers, .... X X X X X X X X X X
Seeding, planting, floating, spraying X X X X X X X X X
equipment, ....
Mounted equipment and tools, ..... X X X X

84423865 25/07/2011
8
 INTRODUCTION

Section Contents
SECTION LETTER DESCRIPTION
HYDRAULIC – A This Section covers the main systems that interact with most of
PNEUMATIC – the functions of the product. It includes the central parts of the
ELECTRICAL – hydraulic, electrical, electronic, pneumatic, lighting and grease
ELECTRONIC lubrication systems. The components that are dedicated to a
SYSTEMS specific function are listed in the Chapter where all the technical
information for that function is included.
ENGINE AND PTO IN B This Section covers all the functions related to the production
of power to move the machine and to drive various devices.
In the case of a pulled-type machine, this Section covers the
power take-off function where power is provided from the towing
machine.
TRANSMISSION, C This Section covers all the functions related to the transmission
DRIVE AND PTO OUT of power from the engine to the axles and to internal or external
devices. This Section also covers the power take-off function
where power is provided to the pull-type machine and additional
Process Drive functions.
AXLES, BRAKES AND D This Section covers all the functions related to moving the
STEERING machine, including tracks, wheels, steering and braking. It covers
all the axles; both driven axles and non-driven axles, including
any axle suspension.
FRAME AND CAB E This Section covers all the main functions and systems related to
the structure and the body of the machine, including the frame,
the shields, the operators cab and the platform. The functions
related to the positioning of the machine frame are included in
Section F, Frame Positioning.
FRAME POSITIONING F This Section covers all the main functions and systems related to
positioning of the machine frame or to positioning the attachment
on the supporting machine frame.
TOOL POSITIONING G This Section covers all the functions related to the final and/or
automatic positioning of the tool once the tool is positioned using
the Working Arm or the machine frame.
HITCH AND H This Section covers all the functions related to the articulated
WORKING TOOL or single arms mounted on the front or rear of the machine. A
working arm can have various tools and quick couplers mounted
on to it. The tools and quick couplers are included in Section J,
Excavating and Landscaping.
EXCAVATING AND J This Section covers all the functions related to the specific tools
LANSCAPING that mount on the front, rear or beside the machine. The tools
described here can be mounted with the positioning systems
(lifting, side shift, swing) listed in Section G Tool Positioning. This
Section covers all the quick coupling systems, located between
the tool and the positioning system. The tools used for field
preparation, soil preparation and treatment, planting and seeding
are included.
CROP PROCESSING K This Section covers all the functions related to crop processing.
Examples of crop processing include threshing, baling,
windrowing, cutting and conditioning.
FIELD PROCESSING L This Section covers all the field processing functions of the
machine. Examples of field process include seeding, fertilizer
application, seedbed preparation and chemical application.

84423865 25/07/2011
9
 INTRODUCTION

This manual contains these Sections:

Contents
INTRODUCTION
HYDRAULIC – PNEUMATIC – ELECTRICAL – ELECTRONIC SYSTEMS A
ENGINE AND PTO IN B
FRAME POSITIONING F
CROP PROCESSING K

Chapters
Each Chapter is identified by a letter and number combination e.g. Engine B.10.A The first letter is identical to the
Section letter i.e. Chapter B.10 is inside Section B, Engine and PTO In.
CONTENTS
The Chapter Contents lists all the technical data (specifications), functional data (how it works), service data (remove,
install adjust, etc..) and diagnostic data (fault codes and troubleshooting) that have been written in that Chapter for
that function or system on the machine.

Contents
ENGINE AND PTO IN
ENGINE _ 10.A
TECHNICAL DATA
ENGINE - General specification (B.10.A)

FUNCTIONAL DATA

ENGINE - Dynamic description (B.10.A)

SERVICE
ENGINE - Remove (B.10.A)

DIAGNOSTIC
ENGINE - Troubleshooting (B.10.A)

INDEX
The Chapter Index lists in alphabetical order all the types of information (called Information Units) that have been
written in that Chapter for that function or system on the machine.

Index
ENGINE AND PTO IN - B
ENGINE
ENGINE - Dynamic description (B.10.A)

ENGINE - General specification (B.10.A)

ENGINE - Remove (B.10.A)

ENGINE - Troubleshooting (B.10.A)

84423865 25/07/2011
10
 INTRODUCTION

Information Units and Information Search

Each chapter is composed of information units. Each information unit has the SAP code shown in parentheses which
indicates the function and the type of information written in that information unit. Each information unit has a page ref-
erence within that Chapter. The information units provide a quick and easy way to find just the right piece of technical
information you are looking for.

Example information unit Stack valve - Sectional View (A.10.A.18)

Information Unit SAP code A 10.A 18
SAP code classification Hydraulic – Primary hydraulic power Stack valve
Pneumatic –
Electrical –
Electronic Systems

CRIL03J033E01A 1

Navigate to the correct information unit you are searching for by identifying the function and information type
from the SAP code.
• (1) Function and (2) Information type.
• (A) corresponds to the sections of the repair manual.
(B) corresponds to the chapters of the repair manual.
(C) corresponds to the type of information listed in the chapter contents, Technical Data, Functional Data, Diag-
nostic or Service.
(A) and (B) are also shown in the page numbering on the page footer.
THE REST OF THE CODING IS NOT LISTED IN ALPHANUMERIC ORDER IN THIS MANUAL.
• You will find a table of contents at the beginning and end of each section and chapter.
You will find an alphabetical index at the end of each chapter.
• By referring to (A), (B) and (C) of the coding, you can follow the contents or index (page numbers) and quickly
find the information you are looking for.

Page Header and Footer

The page header will contain the following references:
• Section and Chapter description

The page footer will contain the following references:

• Publication number for that Manual, Section or Chapter.
• Version reference for that publication.
• Publication date
• Section, chapter and page reference e.g. A.10.A / 9

84423865 25/07/2011
11
 INTRODUCTION

Basic instructions - Important notice regarding equipment servicing

All repair and maintenance work listed in this manual must be carried out only by qualified dealership personnel,
strictly complying with the instructions given, and using, whenever possible, the special tools.

Anyone who performs repair and maintenance operations without complying with the procedures provided herein
shall be responsible for any subsequent damages.

The manufacturer and all the organizations of its distribution chain, including - without limitation - national, regional, or
local dealers, reject any responsibility for damages caused by parts and/or components not approved by the manu-
facturer, including those used for the servicing or repair of the product manufactured or marketed by the manufacturer.
In any case, no warranty is given or attributed on the product manufactured or marketed by the manufacturer in case
of damages caused by parts and/or components not approved by the manufacturer.

The information in this manual is up-to-date at the date of the publication. It is the policy of the manufacturer for
continuous improvement. Some information could not be updated due to modifications of a technical or commercial
type, or changes to the laws and regulations of different countries.

In case of questions, refer to your NEW HOLLAND CONSTRUCTION Sales and Service Networks.

84423865 25/07/2011
12
 INTRODUCTION

Basic instructions - Shop and Assembly

SHIMMING
For each adjustment operation, select adjusting shims and measure individually using a micrometer, then add up
the recorded values. Do not rely on measuring the entire shimming set, which may be incorrect, or the rated value
indicated on each shim.

ROTATING SHAFT SEALS

For correct rotating shaft seal installation, proceed as follows:
• before assembly, allow the seal to soak in the oil it will be sealing for at least thirty minutes.
• thoroughly clean the shaft and check that the working surface on the shaft is not damaged.
• position the sealing lip facing the fluid; with hydrodynamic lips, take into consideration the shaft rotation direction
and position the grooves so that they will deviate the fluid towards the inner side of the seal.
• coat the sealing lip with a thin layer of lubricant (use oil rather than grease) and fill the gap between the sealing
lip and the dust lip on double lip seals with grease.
• insert the seal in its seat and press down using a flat punch or seal installation tool. Do not tap the seal with a
hammer or mallet.
• whilst inserting the seal, check that it is perpendicular to the seat; once settled, make sure that it makes contact
with the thrust element, if required.
• to prevent damaging the seal lip on the shaft, position a protective guard during installation operations.

O-RING SEALS
Lubricate the O-RING seals before inserting them in the seats, this will prevent them from overturning and twisting,
which would jeopardise sealing efficiency.

SEALING COMPOUNDS
Apply one of the following sealing compounds on the mating surfaces when specified: SILMATE® RTV1473, or
LOCTITE® RTV 598 or LOCTITE® INSTANT GASKET 587 BLUE. Before applying the sealing compound, prepare the
surfaces as directed on product container or as follows:
• remove any incrustations using a metal brush.
• thoroughly de-grease the surfaces using a locally approved cleaning agent such as safety solvent or brake parts
cleaner.

SPARE PARTS
Only use "CNH Original Parts" or " NEW HOLLAND CONSTRUCTION Parts".

Only genuine spare parts guarantee the same quality, duration and safety as original parts, as they are the
same parts that are assembled during standard production. Only "CNH Original Parts" or " NEW HOLLAND
CONSTRUCTION Parts" can offer this guarantee.
When ordering spare parts, always provide the following information:
• machine model (commercial name) and serial number
• part number of the ordered part, which can be found in the "Microfiches" or the "Service Parts Catalogue", used
for order processing

84423865 25/07/2011
13
 INTRODUCTION

PROTECTING THE ELECTRONIC/ ELECTRICAL SYSTEMS DURING CHARGING OR WELD-

ING
To avoid damage to the electronic/electrical systems, always observe the following:
1. Never make or break any of the charging circuit connections, including the battery connections, when the engine
is running.
2. Never short any of the charging components to ground.
3. Always disconnect the ground cable from the battery before arc welding on the combine or on any header at-
tached to the combine.
• position the welder ground clamp as close to the welding area as possible
• if welding in close proximity to a computer module, then the module should be removed from the combine
• never allow welding cables to lay on, near or across any electrical wiring or electronic component while
welding is in progress
4. Always disconnect the negative cable from the battery when charging the battery in the combine with a battery
charger.
NOTICE: If welding must be performed on the unit, either the combine or the header (if it is attached), the battery
ground cable must be disconnected from the combine battery. The electronic monitoring system and charging system
will be damaged if this is not done.

Remove the battery ground cable. Reconnect the cable when welding is completed.

WARNING
Battery acid causes severe burns. Batteries contain sulfuric acid. Avoid contact with skin, eyes or clothing.
Antidote - EXTERNAL: flush with water. INTERNAL: drink large quantities of water or milk. Follow with milk
of magnesia, beaten egg or vegetables oil. Call physician immediately. EYES: flush with water for 15 minutes
and get prompt medical attention.
84-110

TOOLS
The tools that NEW HOLLAND CONSTRUCTION suggests and illustrate in this manual have been:
• specifically researched and designed for use with NEW HOLLAND CONSTRUCTION machines
• essential for reliable repair operations
• accurately built and rigorously tested so as to offer efficient and long-lasting operation

By using these tools, repair personnel will benefit from:

• operating in optimal technical conditions
• obtaining the best results
• saving time and effort
• working in safe conditions
NOTE: The terms "front", "rear", "right-hand" and "left-hand" (when referred to different parts) are determined from
the rear, facing in the direction of travel of the machine during operation.

84423865 25/07/2011
14
 INTRODUCTION

Torque - Minimum tightening torques for normal assembly

2 - Series

METRIC NON-FLANGED HARDWARE

NOM. LOCKNUT LOCKNUT
SIZE CL.8 CL.10
CLASS 8.8 BOLT and CLASS 10.9 BOLT and W/CL8.8 W/CL10.9
CLASS 8 NUT CLASS 10 NUT BOLT BOLT
PLATED PLATED
UNPLATED UNPLATED
W/ZnCr W/ZnCr
2.2 N·m (19 lb 2.9 N·m (26 lb 3.2 N·m (28 lb 4.2 N·m (37 lb 2.9 N·m (26 lb
M4 2 N·m (18 lb in)
in) in) in) in) in)
4.5 N·m (40 lb 5.9 N·m (52 lb 6.4 N·m (57 lb 8.5 N·m (75 lb 5.8 N·m (51 lb
M5 4 N·m (36 lb in)
in) in) in) in) in)
7.5 N·m (66 lb 10 N·m (89 lb 11 N·m (96 lb 15 N·m (128 lb 6.8 N·m (60 lb 10 N·m (89 lb
M6
in) in) in) in) in) in)
18 N·m (163 lb 25 N·m (217 lb 26 N·m (234 lb 35 N·m (311 lb 17 N·m (151 lb 24 N·m (212 lb
M8
in) in) in) in) in) in)
49 N·m (36 lb 70 N·m (51 lb 33 N·m (25 lb 48 N·m (35 lb
M10 37 N·m (27 lb ft) 52 N·m (38 lb ft)
ft) ft) ft) ft)
85 N·m (63 lb 121 N·m (90 lb 58 N·m (43 lb 83 N·m (61 lb
M12 64 N·m (47 lb ft) 91 N·m (67 lb ft)
ft) ft) ft) ft)
158 N·m (116 lb 210 N·m (155 225 N·m (166 lb 301 N·m (222 143 N·m (106 lb 205 N·m (151 lb
M16
ft) lb ft) ft) lb ft) ft) ft)
319 N·m (235 lb 425 N·m (313 440 N·m (325 lb 587 N·m (433 290 N·m (214 lb 400 N·m (295 lb
M20
ft) lb ft) ft) lb ft) ft) ft)
551 N·m (410 lb 735 N·m (500 762 N·m (560 lb 1016 N·m (750 501 N·m (370 lb 693 N·m (510 lb
M24
ft) lb ft) ft) lb ft) ft) ft)

NOTE: M4 through M8 hardware torque specifications are shown in pound-inches. M10 through M24 hardware torque
specifications are shown in pound-feet.

84423865 25/07/2011
15
 INTRODUCTION

METRIC FLANGED HARDWARE

NOM. CLASS 8.8 BOLT and CLASS 10.9 BOLT and LOCKNUT LOCKNUT
SIZE CLASS 8 NUT CLASS 10 NUT CL.8 CL.10
W/CL8.8 W/CL10.9
BOLT BOLT
PLATED PLATED
UNPLATED UNPLATED
W/ZnCr W/ZnCr
2.4 N·m (21 lb 3.2 N·m (28 lb 3.5 N·m (31 lb 4.6 N·m (41 lb 2.2 N·m (19 lb 3.1 N·m (27 lb
M4
in) in) in) in) in) in)
4.9 N·m (43 lb 6.5 N·m (58 lb 7.0 N·m (62 lb 9.4 N·m (83 lb 4.4 N·m (39 lb 6.4 N·m (57 lb
M5
in) in) in) in) in) in)
8.3 N·m (73 lb 11 N·m (96 lb 12 N·m (105 lb 16 N·m (141 lb 7.5 N·m (66 lb 11 N·m (96 lb
M6
in) in) in) in) in) in)
20 N·m (179 lb 27 N·m (240 lb 29 N·m (257 lb 39 N·m (343 lb 18 N·m (163 lb 27 N·m (240 lb
M8
in) in) in) in) in) in)
54 N·m (40 lb 77 N·m (56 lb
M10 40 N·m (30 lb ft) 57 N·m (42 lb ft) 37 N·m (27 lb ft) 53 N·m (39 lb ft)
ft) ft)
93 N·m (69 lb 100 N·m (74 lb 134 N·m (98 lb
M12 70 N·m (52 lb ft) 63 N·m (47 lb ft) 91 N·m (67 lb ft)
ft) ft) ft)
174 N·m (128 lb 231 N·m (171 248 N·m (183 lb 331 N·m (244 158 N·m (116 lb 226 N·m (167 lb
M16
ft) lb ft) ft) lb ft) ft) ft)
350 N·m (259 lb 467 N·m (345 484 N·m (357 lb 645 N·m (476 318 N·m (235 lb 440 N·m (325 lb
M20
ft) lb ft) ft) lb ft) ft) ft)
607 N·m (447 lb 809 N·m (597 838 N·m (618 lb 1118 N·m (824 552 N·m (407 lb
M24
ft) lb ft) ft) lb ft) ft)

IDENTIFICATION

Metric Hex head and carriage bolts, classes 5.6 and up

20083680 1

1. Manufacturer's Identification
2. Property Class

Metric Hex nuts and locknuts, classes 05 and up

20083681 2

84423865 25/07/2011
16
Thanks very much for your reading,

Want to get more information,

Please click here, Then get the complete

manual

NOTE:
If there is no response to click on the link above,
please download the PDF document first, and then
click on it.

Have any questions please write to me:

admin@servicemanualperfect.com