Fiber Manhole Procedure - Preservation, Storage and Handling

AMIANTIT FIBERGLASS INDUSTRIES LIMITED COMPANY (DAMMAM)
HANDLING, STORAGE AND PRESERVATION OF PIPES & FITTINGS
This Procedure is the property of AFIL. It must not be reproduced in whole or in part of otherwise
disclosed without prior written consent.
The official controlled copy of this procedure is the digitally signed/approved PDF document held
within our network server and visible to all authorized users. All printed copies, and all electronic
copies and versions, except the ones described above, are considered uncontrolled copies which
should be used for reference only.
Amiantit Fiberglass Industries Ltd (AFIL)

1st Industrial city, P.O. Box 3430
DAMMAM, 31471, Saudi Arabia
Phone: +966 (13) 812-1001

Fax: +966 920004070 ,,, 6208
www.amiantit.com
Date: 01ST May 2023 Document No: SP 01 Revision Number 01
Approval:
This signatures below or approval through electronic media as determined in this procedure certify that this
management system procedure has been reviewed and accepted and demonstrates that the signatories are
aware of all the requirements contained herein and are committed to ensuring their provision.
Date: Date: Date:
Prepare By: Reviewed By: Approved By:

Muhammad Zohaib khan Mohammed Kaleem Pasha Toufiq Mohammed Qaddam
QA Controller Shipping Controller Central Warehouse Manager
Amendment Record:
This Procedure is reviewed to ensure its continuing relevance to the systems and process that it describes. A
record of contextual additions or omissions is given below.
Page No. Context Rev No Date

Initial issuance of Document in new format 01 01-05-2023
Controlled Copy UnControlled Copy
Page 1 of 3
Scope:
This procedure provides guidance for the
Preservation, Storage and Handling of Glass
Reinforced Plastic (GRP) pipes and Fittings.
Handling:
• Package Load:
Pipes 1400mm and smaller in diameter are
packaged as a unit. Packages may be handled using
a pair of slings as shown in (figure 2.1) Figure 2.3 (Lifting Pipe at Two Support Points)
• Handling Nested Pipes:
Nested group pipes refer to a method of
organizing and packing pipes in which smaller
pipes are placed inside larger once. Nested group
pipes are typically sorted and grouped based on
their size, with smaller pipes nested inside larger
ones to form groups. These pipes generally have
special packing and it require mutually
agreement between supplier and customer.
Figure 2.1(Lifting Pipe Package) Regardless the following general procedure
• Single Pipes: should always be followed.
Single pipes must be loaded and handled separately

(one at a time). Use pliable straps, Slings, or ropes to
lift single pipes. Do not use steel cables or chains to
lift or transport the pipe. Pipe sections can be lifted
with only one support point (Figure 2.2) although
two support points placed as in (Figure 2.3) make the
pipe easier to control. Do not lift pipe by passing a
rope through the section end to end.
Figure 2.6 (Double Support Point)
• Fitting Load:
Fitting should be supported along their entire
length during transportation, Storage, and
handling. Blocking or wood should be used to
prevent fitting from rolling or moving during
transportation.
Fitting should be properly secured to prevent
movement during transportation. Strapping or
binding with appropriate material such as nylon
Figure 2.2 (Lifting Pipe at one Support Point)
webbing may be used.
Page 2 of 3
Storage: ➢ Store the pipes in their intended orientation with

• Pipe Storage: sufficient space between them to prevent
contact. Do not stack pipes directly on top of
It is generally advantageous to store pipe on flat each other.
timber to facilitate placing and removal of lifting ➢ Fiberglass pipes and fittings shall be place on
slings around the pipe. shipping or wooden support resting only on firm
When storage pipe directly on the ground, be sure level surface during storage or repositioning.
that the area is relatively flat and free of rock and ➢ Pipe and fittings shall not be rested on stones,
other potential damaging debris. tools, chocks, or other small hard objects.
All pipes should be chocked to prevent rolling in ➢ If stored outdoors, Pipes and fittings shall be
high winds. adequately tied down to prevent movement
If it is necessary to stack pipes, it is best to stack on from wind or water flotation.
flat timber supports at maximum 6 meter spacing ➢ Fiberglass pipes and fittings are designed and
(3 meter for small diameter) with chocks (Figure 2.4) manufactured with corrosion resistant material
suitable for environment.
➢ Pipes and fittings are manufactured and
delivering to site after the completion of
required passivation’s.
➢ The storage location or installation area shall be
protected from any vehicle movements to avoid
accidental damages.
• Re-preservation of Pipes and Fittings:
Before re-preserving pipes and fittings, it is

Figure 2.3 (Lifting Pipe at Two Support Points)
important to clean them thoroughly to remove any
Ensure the stack will be stable for conditions such dirt or debris. Use air pressure or water to clean the
as high winds, un-level storage area or other pipes and fittings. After cleaning, inspect the pipes
horizontal loads. Maximum stack height is and fittings for any signs of damage, such as cracks.
approximately 2 meters. Stacking of pipes larger If any damage is found, repair it before proceeding
than 1400mm diameter is not recommended. with re-preservation.
• Fitting Storage:
Fitting should not be stacked directly on top of
each other, as this can cause deformation or
damage. Instead, they should be stacked on pallets
with sufficient space between them to prevent
contact.
Preservation:
• Pipes and Fitting:
➢ Choose a clean and dry area. Ensure that the
area is free from any sources of contamination
such as chemical , oil, or dust.
Page 3 of 3

Fiber Manhole Procedure - Preservation, Storage and Handling

Uploaded by

Copyright:

Available Formats

Fiber Manhole Procedure - Preservation, Storage and Handling

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Fiber Manhole Procedure - Preservation, Storage and Handling

Uploaded by

Copyright:

Available Formats

AMIANTIT FIBERGLASS INDUSTRIES LIMITED COMPANY (DAMMAM)

HANDLING, STORAGE AND PRESERVATION OF PIPES & FITTINGS

Amiantit Fiberglass Industries Ltd (AFIL)

Phone: +966 (13) 812-1001

Date: Date: Date:

Prepare By: Reviewed By: Approved By:

Page No. Context Rev No Date

Controlled Copy UnControlled Copy

Single pipes must be loaded and handled separately

Storage: ➢ Store the pipes in their intended orientation with

• Re-preservation of Pipes and Fittings:

Before re-preserving pipes and fittings, it is

You might also like