Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                

vm5w2 Se

Download as pdf or txt
Download as pdf or txt
You are on page 1of 1

MODEL VM-5W2 DUAL POWER SUPPLY

VM-5 SERIES MONITOR


INSTRUMENT RACK *4
SPECIFICATIONS
(for VM-5Z5,6,7) 4

No entry if additional
Model Code / Additional Spec. Code( spec. code is not specified. )

VM-5W 2- /TRP

Number of VM-5 Tropical


Husing fix screw size
monitor units spec.
2 Max.10 units *1 0 #4-40UNC
1 M2.6×0.45
Note) *1 Max.8 units when VM-5Z0 Power Supply Backup Module is installed.

Standard Specifications Standard Specifications


INPUT FOR Alarm reset(normally open) ALARM Function : System OK(common to all channels)*3
OPERATION Sequence(normally open) CONTACT Contact capacity :
(FROM REAR Filter enable(normally open) OUTPUT load resistance : 250VAC,5A
PANEL) Contact type : Dry contact : 30VDC,5A
SERIAL INTERFACE D-Sub connector 9P 2pc. (IN,OUT) Contact type : C contact•Dry contact
INPUT/OUTPUT CONTACT LIFE 100,000 times or more(rated load)
Housing fix screw : #4-40UNC or M2.6×0.45
CONNECTOR *6 PROTECTIVE Plastic sealed
Specified when ordering.
Unless specified otherwise, preset to #4-40UNC. CONSTRUCTION
Recommended connector(Socket side) TEMPERATURE Operating temperature :
Connector Housing RANGE 0 to 65°C(32 to 149°F REF.)*2
XM2D-0901 XM2S-0913(#4-40UNC) Relative Humicity : 20 to 95%RH(noncondensing)
XM2S-0911(M2.6×0.45 ) [OMRON] MATERIAL AND Rack(Top plate,Bottom plate) : ZAM-ZC
GM(E)-9F GM-9LD55GU(#4-40UNC) FINISH Rack(Side plate) : SPCC Munsell N-1.0(equiv.)
GM-9LD55G(M2.6×0.45 ) [HONDA] Face plate : Aluminum Munsell N-4.0(equiv.)
OPERATION DANGER bypass switch MASS max.10kg(max.22lb REF.)
SWITCH OTHERS
INDICATOR Power supply 1 OK indicator : Green LED
Power supply 2 OK indicator : Green LED

Note) *2 Operating temperature is to 0 to 50°C(32 to 122°F REF.) when VM-5Z0 Power Supply Backup Module
is installed.
*3 The system OK alarm contacts are not functional unless the VM-5P is mounted.
*4 CE means conformity with EC directive for only the rack, but not for all the units which are installed in
the rack, nor for the whole system.
*5 Ventilation holes are drilled through the top and bottom faces of the instrument rack for natural
cooling. When mounting the instrument rack within the panel, do not close these ventilation holes. If
closed, the temperature in the rack may rise to shorten the service life of electronic parts used.
Do not place anything which interrupts ventilation within 200 mm from top and bottom faces of the
instrument rack.
Do not place the apparatus which generates heat under the instrument rack.
Be careful when installing the instrument rack in a bad-ventilated closed box (instrument panel).
It may cause shortening the life time of electronic parts because of marked rising in temperature of
the instrument rack in a bad-ventilated closed box which keeps the heat in.
Cool down inside the box with a cooling fan or the like.
Especially when installing in a small closed box, use the forced-air cooling apparatus like an
electronic air conditioner.
*6 The serial interface input/output connectors are not functional unless the VM-5P1,2 is mounted.
*7 This product cannot be used in combination with VM-5Z1, VM-5Z2, or VM-5Z3. Please be sure to
use it in combination with VM-5Z5 (VM-5Z1 successor Model), VM-5Z6 (VM-5Z2 successor Model),
and VM-5Z7 (VM-5Z3 successor Model).

6H23-021
Issued: Jun. 2023

You might also like