Micron csn11

CSN-11: Product Marks/Product and Packaging Labels
Introduction
Customer Service Note

Product Marks, Product Labels, and Packaging Labels
Introduction
Micron uses various marks and labels on our products and packaging. The first section
of this customer service note describes the product marks and labels we place on our
devices. The second section describes the labels used on and in our packaging.
PDF: 09005aef80d6313a/Source: 09005aef80d5e2c2/CCMTD-1725822587-10407 Micron Technology, Inc., reserves the right to change products or specifications without notice.
CSN11.fm - Rev. AU 12/22 EN 1 ©2003 Micron Technology, Inc. All rights reserved.
Products and specifications discussed herein are for evaluation and reference purposes only and are subject to change by
Micron without notice. Products are only warranted by Micron to meet Micron’s production data sheet specifications. All
information discussed herein is provided on an “as is” basis, without warranties of any kind.
Table of Contents
Table of Contents
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
List of Figures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
List of Tables. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Product Marks and Labels. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Component Mark Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Abbreviated Component Mark Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Module Label Data and Examples . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Process Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
SSD Label Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
SD and microSD Label Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
Micron Packaging Labels. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
Master Container Labels. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
Bar Code Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
Individual Packaging Labels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
Revision History. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
PDF: 09005aef80d6313a/Source: 09005aef80d5e2c2 Micron Technology, Inc., reserves the right to change products or specifications without notice.
CSN11TOC.fm - Rev. AU 12/22 EN 2 ©2003 Micron Technology, Inc. All rights reserved.
List of Figures
List of Figures
Figure 1: TSOP Component Mark . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Figure 2: SOP2/W-PDFN/BGA/LGA Abbreviated Component Mark. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Figure 3: Legacy BGA Component with Elpida Part Mark . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Figure 4: DDR5 LRDIMM, RDIMM, UDIMM and SODIMM DRAM Module Label Content. . . . . . . . . . . . . . . . .8
Figure 5: DDR4/DDR3 LRDIMM, RDIMM, UDIMM and SODIMM DRAM Module Label Content . . . . . . . . . .9
Figure 6: DDR4/DDR3 NVDIMM Additional Label Content . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Figure 7: DDR4/DDR3 ECC UDIMM/SODIMM Label Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Figure 8: SSD MID Label . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Figure 9: Micron Standard SATA/NVMe 2.5/U.x SSD Label Structures. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Figure 10: Micron Standard SATA/NVMe M.2 SSD Label Structures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
Figure 11: Micron Standard NVMe E1.x SSD Label Structures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Figure 12: MID/CERT Label Structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Figure 13: Embedded USB Label Structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Figure 14: Micron SD Label Structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
Figure 15: Micron microSD Label Structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
Figure 16: Micron SD Backside Markings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
Figure 17: Micron microSD Backside Markings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
Figure 18: Standard Master Container Shipping Label . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
Figure 19: Standard Master Container Bar Code Label . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
Figure 20: Standard Bar Code Label. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
Figure 21: Micron’s Inner Packing Container Label. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
Figure 22: Micron’s Inner Packing Container Label for Modules and SSDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
Figure 23: Micron’s Moisture Sensitivity (MST) Label. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
Figure 24: Labeling on Moisture-Barrier and Static-Shielding Bags1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
CSN11LOF.fm - Rev. AU 12/22 EN 3 ©2003 Micron Technology, Inc. All rights reserved.
List of Tables
List of Tables
Table 1: DDR3 Process Code Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Table 2: DDR4 RDIMM, NVDIMM1 Process Code Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Table 3: DDR4 LRDIMM Process Code Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Table 4: DDR4 NVDIMM Process Code Third Character Options. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Table 5: DDR5 Process Code Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Table 6: Module Manufacturing Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Table 7: SSD Label Mark Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
CSN11LOT.fm - Rev. AU 12/22 EN 4 ©2003 Micron Technology, Inc. All rights reserved.
Product Marks and Labels

Most of Micron’s component products use one of two product mark variations to
accommodate smaller components and different package sizes (for example, FBGA and
CSP). Both product marks are right- and left-justified and have a character height of
0.040–0.050 inches depending on package size. Both marks also include a unique, laser-
inscribed identification number on the top side of the part for traceability purposes.
Legacy component products with Elpida part marks use the same part marks used prior
to Micron's acquisition of Elpida. Further information may be found in our product
guides and on Micron’s Web site: www.micron.com/numbering.
Component Mark Information

Most component marks contain the following details (see Figure 1 on page 6):
• Date code (year and workweek)
• Special mark characters
• Country of diffusion (see below for country codes)
• Country of encapsulation (see below for country codes)
• Micron® mark or logo
• Product family
• Process technology
• Device number
• Device versions
• Package type
• Speed
• Special test option (if relevant)
• Die revision
• Scribe
For more information on product-specific designators, see the part numbering guides
on Micron’s Web site: www.micron.com/numbering.
Codes for the countries of diffusion and encapsulation:
1 = USA 5 = China B = Israel
2 = Singapore 7 = Taiwan C = Ireland
3 = Italy 8 = Korea D = Malaysia
4 = Japan 9 = Mixed F = Philippines
CSN11_2.fm - Rev. AU 12/22 EN 5 ©2003 Micron Technology, Inc. All rights reserved.
Figure 1: TSOP Component Mark

2D barcode of 8
Ball 1 or digit part identifier
mark (select products)
Function Special
mark mark
Week code characters characters
(optional) (optional) Country of
Year code
encapsulation
Country of
diffusion
– –
Device number
Micron
mark Scribe
or logo
Product family Process technology Device
versions
Die revision
Package type Speed Special test
options or blanks
Abbreviated Component Mark Information

Due to space limitations, FBGA-package component marks contain abbreviated details
for two distinct types of information (see Figure 2 on page 7). The top row of the compo-
nent mark contains the flooring details that are unrelated to product type:
• Date code (see below)
• Die revision
• Country of diffusion (see below for country codes)
• Country of encapsulation (see below for country codes)
Date codes are alphanumeric characters that indicate the year and workweek the parts
were marked, in even-numbered workweeks. The first character is the last number in the
year, and the second (alpha) character is the workweek.
A=2 E = 10 I = 18 M = 26 Q = 34 U = 42 Y = 50
B=4 F = 12 J = 20 N = 28 R = 36 V = 44 Z = 52
C=6 G = 14 K = 22 0 = 30 S = 38 W = 46
D=8 H = 16 L = 24 P = 32 T = 40 X = 48
Codes for the countries of diffusion and encapsulation:
1 = USA 5 = China B = Israel
2 = Singapore 7 = Taiwan C = Ireland
3 = Italy 8 = Korea D = Malaysia
4 = Japan 9 = Mixed F = Philippines
The middle and bottom rows of the component mark contain product-specific details such as:
• Micron logo/ball 1 designator
• Coded part number
• Product family
• Special mark characters
More information on product-specific designators is provided in Micron’s various part

numbering guides, which are available on Micron’s Web site at www.micron.com/
numbering. Information on the corresponding part numbers for part mark codes is
available from the FBGA Part Marking Decoder at www.micron.com/decoder.
Figure 2: SOP2/W-PDFN/BGA/LGA Abbreviated Component Mark
2D barcode of Die
the PSID (select revision
Country
products) of diffusion
Date Country
code of encapsulation
Scribe
(If space
allows)
Product Coded part number

family
Function mark Special mark

characters characters
(optional) (optional)
2D barcode of 8
Ball 1 and/or digit part identifier
or lead 1
(See Note 1) (select products)
mark
Notes: 1. If the “MT” and “dot” are both present, ball 1 or lead 1 are identified by the “dot.”
2. For BGA packages, the scribe and ball 1 or lead 1 indicator may swap positions if the pack-
age is wider than its length. The scribe and ball 1 or lead 1 indicator will always be marked
along the short side of the component.
Figure 3: Legacy BGA Component with Elpida Part Mark
Product name
(mark name,
may have
multiple lines)
Lot Engineering
number sample (ES)
mark
Year
assembled
Week In-house
assembled code
Ball 1
mark
Module Label Data and Examples

Labels used for module production have standard requirements for each line printed on
the label, but can vary by type (see Figure 4 through Figures 7). Micron’s module label
content and format conform to JEDEC label specifications.
Figure 4: DDR5 LRDIMM, RDIMM, UDIMM and SODIMM DRAM Module Label Content
1
PN:MTC120F41616CSZALB48BA1 ABCDEF 13
12
2 DDR5 EC8 RDIMM Product of CHINA
256GB 2S16Rx16 PC5-5200C-RAB0-1010-XT 11
SN: 802CXXYYWW12345678 BZAE5EH001
3 5
6 7 8 9 10
4
Key note definitions:

1. Code 128 subset B bar code (per ISO/IEC 15417:2007) of Micron part number/date-
code (YWW) with a space separator between the data. Example:
– MTC120F41616CSZALB48BA1 126
2. 2D barcode (see JEDEC DDR5 DIMM Label Specification)
– (L)technical details(S)serial number(P)part number(c)process code
3. Micron DRAM module marketing part number
3a. For more information about module part numbering, see Module Part Number-
ing Systems on micron.com
4. DRAM technology
5. JEDEC technical details (see JEDEC DDR5 DIMM Label Specification):
5a. Module capacity, ranks, and number of data lines per DRAM device (256GB
2S16Rx16 shown)
5b. DRAM technology (PC5 shown)
5c. Module speed bin (5200C shown)
5d. Module type, reference raw card and revision (RAB0 shown)
5e. JEDEC SPD revision (1010 shown)
5f. Temperature grade (XT shown)
6. JEDEC serial number (see JEDEC DDR5 DIMM Label Specification)
6a. Micron’s JEDEC manufacturer code, 802C (constant on all modules)
6b. Manufacturing location (two characters, variable—see Table 6)
6c. Date code (four characters: YYWW)
6d. Module serial number (eight characters, unique to each module)
7. Module build lot ID
8. Micron logo
9. The UK Regulatory Requirement mark (may or may not be present on a particular
module label)
10. The European Regulatory Requirement mark (may or may not be present on a partic-
ular module label)
11. Module assembly country of origin; Micron uses:
– “Made in Taiwan” for Taiwan origin product
– “Assembled in USA” for US origin product
– “Product of xxx” for products of other origins
12. Module DIMM type

13. A process code is printed after the last character of module part numbers (ABCDEF
shown; see Table 5). This additional information provided is not part of the module
part number.
Figure 5: DDR4/DDR3 LRDIMM, RDIMM, UDIMM and SODIMM DRAM Module Label Content
1
2 MT144JSZS2G72LZ-1G4FXA2ESBB
16GB 2RX8 PC3-10600V-9-10-B0
3 Product of CHINA
BZAJAEY001 2126
4 5 6 7 9 10 11

1. Code 128 subset B bar code (per ISO/IEC 15417:2007) of Micron part number/date
code (YWW) with a space separator between the data. Example:
MTA18ASF1G72PDZ-2G6B1QG 126
ing Systems on micron.com (see also number 8 below)
3. Micron logo
– "Made in Taiwan" for Taiwan origin product
– “Assembled in USA" for US origin product
– "Product of xxxx" for products of other origins
6. Module date code, four characters (YYWW)
7. DDR4 JEDEC label text (see JEDEC document Module 4.20.28)
7a. Module capacity, ranks, and number of data lines per DRAM device (8GB 2RX8
shown)
7b. DRAM technology (PC4 shown)
7c. Module speed bin (2666V shown)
7d. Module type, reference raw card and revision (REB shown)
7e. JEDEC SPD revision (11 shown)
8. A process code is printed after the last character of RDIMM, LRDIMM, NVDIMM, and
ECC UDIMM/SODIMM module part numbers (QG shown; see Tables 1–3). This addi-
tional information is not part of the module part number.
8a. The process code for ECC UDIMM and SODIMM labels differ slightly as shown in
Figure 7. Labels on UDIMMs and SODIMMs without ECC do not have a process
code appended to the part number.
module label)
10. 2D barcode – Encoded data string (per ISO/IEC 15426-2:2005)
10a. Data identifier, S (constant on all modules)
10b. Micron's JEDEC manufacturer code, 802C (constant on all modules)
10c. Manufacturing location, two characters, variable (see Table 6)
10d. Datecode, four characters (YYWW)
10e. Module serial number, eight characters, unique to each module

ular module label)
Figure 6: DDR4/DDR3 NVDIMM Additional Label Content
1
MTA18ASF1G72PF1Z-2G1T11AAIGE
8GB 1RX4 NN4-2133P-RZZZ-10
Assembled in USA 2126
NVRDIMM-N FW:2.40
S/N:802C01212612345678 BZAJAEY001
2 3 4
Micron’s NVDIMM label has content not included on the standard label. This additional
content is described below.
1. The process code on the NVDIMM label includes a third character (E shown) that
identifies the multiplexer (MUX) vendor and device ID (See Table 4)
2. JEDEC hybrid memory module type; function designators:
N = Persistent
F = Block
P = Combined
3. 2D barcode and human-readable text – Encoded data string (per ISO/IEC 15426-2:2005)
3a. Data identifier, S (constant on all modules), applies only to barcode area
4. Firmware revision
Figure 7: DDR4/DDR3 ECC UDIMM/SODIMM Label Example

1
2 MT18KSF1G72AZ-1G6P1ZG
8GB 2RX8 PC3L-12800E-11-13-E3
3 Product of China
CBNEXXX001 2126
4 5 6 7 9 10 11

1. Code 128 subset B bar code (per ISO/IEC 15417:2007) of Micron part number/date
code (YWW) with a space separator between the data
ing Systems on micron.com (see also number 8 below)
3. Micron logo
4. Module date code, four characters (YYWW)
– "Made in Taiwan" for Taiwan origin product

– "Assembled in USA" for US origin product
– "Product of xxxx" for products of other origins
7. DDR3 JEDEC label text (See JEDEC Doc. Module 4.20.20)
7a. Module capacity (8GB shown)
7b. Module ranks and number of data lines per DRAM device (2RX8 shown)
7c. DRAM technology and supply voltage (VDD; PC3L shown)
7d. Module speed bin (12800 shown)
7e. Module type (E shown)
7f. CAS Latency, in clocks (11 shown)
7g. JEDEC SPD revision (13 shown)
7h. Reference raw card and revision (E3 shown)
8. A two-character process code is printed after the last character of the module part
numbers (QG shown; see Tables 1-3). This additional information provided is not part
of the module part number
8a. The first character of the process code, Z, is a place holder that means there is no
register on the module
8b. The second character, G in this case, identifies the temperature sensor manufac-
turer and device version
module label)
10. 2D barcode – Encoded data string (per ISO/IEC 15426-2:2005)
10a. Data identifier, S (constant on all modules)
ular module label)
Non-ECC UDIMM and SODIMM module labels do not have a process code ID printed
on the label.
Process Codes
The following tables provide the process code options for DDR3 register, DDR4 register
clock driver (RCD) and MUX, DDR5 RCD, PMIC, HUB, and temperature sensor/
EEPROM devices.
Table 1: DDR3 Process Code Options
Register
Vendor ID Temp Sensor/ Temp Sensor/
Register (First Register Vendor Part Temp Sensor/ EEPROM Vendor ID EEPROM Vendor
Vendor Character) Number EEPROM Vendor (Second Character) Part Number
IDT D SSTE32882HLBAKG8 ST Micro E STTS2002B2DN3F
H SSTE32882KA1AKG8 Microchip F MCP98243T-BE/
MNYAA
M SSTE32882KB1AKG8 NXP G SE97BTP-547
Inphi A INSSTE32882LV-GS02
F INSSTE32882UV-GS02
K INSSTE32882XV-GS02
Montage N M88SSTE32882H0-T
TI B SN74SSQEA32882ZALR
G SN74SSQEB32882ZALR
L SN74SSQEC32882ZALR
None Z –
Table 2: DDR4 RDIMM, NVDIMM1 Process Code Options
RCD Vendor Temp Sensor/ Temp Sensor/

RCD ID (First RCD Vendor Part Temp Sensor/ EEPROM Vendor ID EEPROM Vendor
Vendor Character) Number EEPROM Vendor (Second Character) Part Number
IDT I 4RCD0124KC0ATG IDT G TSE2004GB2B0NCG8
S 4RCD0229KB1ATG8 ST Micro I STTS2004B2DN3F
V 4RCD0232KC1ATG8 Microchip K MCP98244T-BE/MNY
Inphi K IDDR4RCD-GS02 Renasas L TSE2004GB2C0NCG8
R IDDR4RCD2-GS01
Rambus A (NVDIMM) IDDR4NVRCD2-GS02
U IDDR4RCD2-GS03
Montage H M88DDR4RCD01B1-T
M M88DDR4RCD01C0-T
Q M88DDR4RCD02A0-T
T M88DR4RCD02PH1
TI J CAB4AZNRR
None Z –
Notes: 1. DDR4 NVDIMMs’ process code includes a third character that identifies the multiplexer
(MUX) vendor and device version (see Table 4).
Table 3: DDR4 LRDIMM Process Code Options
RCD/Data
Buffer RCD Vendor Part
RCD/Data Vendor ID Number Temp Sensor/ Temp Sensor/
Buffer (First Data Buffer Vendor Temp Sensor/ EEPROM Vendor ID EEPROM Vendor
Vendor Character) Part Number EEPROM Vendor (Second Character) Part Number
IDT I 4RCD0124KC0ATG IDT G TSE2004GB2B0NCG8
4DB0124KB1AVG53
P 4RCD0124KC0ATG ST Micro I STTS2004B2DN3F
4DB0226KA3AVG
S 4RCD0229KB1ATG8 Microchip K MCP98244T-BE/MNY
4DB0226KB0AVG8
V 4RCD0232KC1ATG8 Renasas L TSE2004GB2C0NCG8
4DB0232KC2AVG8
Montage H M88DDR4RCD01B1-T
M88DDR4DB01A1-T
M M88DDR4RCD01C0-T
M88DDR4DB01B0-T
Q M88DDR4RCD02A0-T
M88DDR4DB02A1-T
T M88DR4RCD02PH1
M88DR4DB02PH2-T
None Z –
Table 4: DDR4 NVDIMM Process Code Third Character Options
MUX Vendor Process Code Character Vendor Part Number

TI D TS3DDR4000ZBAR
NXP E CBTV24DD12
Table 5: DDR5 Process Code Options
Position (SODIMM/
UDIMM) Position (RDIMM) Code Part Type Vendor Vendor Part Number
1st N/A B Client PMIC Renesas P8911-Y0Z001FNG
1st N/A C Client PMIC MPS MP5431GLT-0010-Z
1st N/A J Client PMIC Richtek RTQ5132GQWF-310
1st N/A K Client PMIC MPS MP5431GLT-0012-Z
N/A 1st F Server PMIC Renesas P8900-X0Z001FNG
N/A 1st G Server PMIC MPS MPQ8895GU-0010-Z
N/A 1st H Server PMIC MPS MPQ8894GU-0010-Z
N/A 1st I Server PMIC TI TPS53830RWZR
N/A 1st J Server PMIC TI TPS53832RWZR
N/A 1st M Server PMIC MPS MPQ8895GU-0011-Z
N/A 1st N Server PMIC MPS MPQ8894GU-0011-Z
N/A 1st P Server PMIC Richtek RTQ5119AGQVF-71
N/A 2nd G RCD Renesas 5RCD0148HC3AVG
N/A 2nd H RCD Rambus DDR5RCD1-G1EX
N/A 2nd I RCD Montage M88DR5RCD01B2
N/A 2nd M RCD Montage M88DR5RCD02A1-T
2nd 3rd C HUB Renesas SPD5118-Y1B000NCG
2nd 3rd F HUB Montage M88SPD5118A5-T
N/A 4th F TempSensor Montage M88TS5110A4-T
N/A 4th C TempSensor Renesas TS5111-Z2AHRI
Table 6: Module Manufacturing Locations
Location ID Number Hexadecimal Value

SIG (USA) 1 0x01
MTB (Taiwan) 2 0x02
MNG (Malaysia) 5 0x05
MMP (Malaysia) 6 0x06
SING (Singapore) 8 0x08
MXA (China) 15 0x0F
TSMT (Taiwan) 37 0x25
Hotayi (Malaysia) 26 0x1A
SSD Label Information

Figures 8 through 13 show representative label structures for our SSD products. The
table below provides the details of each particular item found on the various labels. Not
all items are present on all labels.
Micron has added a manufacturing identification (MID) label to all SSD products. This
2D barcode label is for Micron internal use only.
Figure 8: SSD MID Label
T5A100C2W
Table 7: SSD Label Mark Definitions
Mark or Text Example Definitions

Micron logo
Market segment, form factor, product and FIPS security (if applicable)
XXXX U.X
Example: 1100 2.5 SSD FIPS 140-2 L2
The device’s voltage level with its related amperes at normal operation (defined by
XV X.XA
Micron QRA)
F/W: XXXXXXXX Drive firmware revision number
Data matrix (2D) barcode containing the PSID (if applicable for a security feature
enabled drive) or the drive serial number, drive part number and PSID
Reserved for the official USA Federal Communications Commission (FCC) mark
Reserved for the official China Restriction of Hazardous Substances mark

This device must meet the standards of China RoHS to enable the 20 year indication of
the RoHS mark
Reserved for the official Japan VCCI mark
Reserved for the official mark based on the drive interface (SATA, NVMe, and so on)

Reserved for the official Ukraine mark
Reserved for the official Taiwan Bureau of Standards Metrology and Inspection (BSMI)
mark.
In addition, the certification number assigned to this Micron product shall be listed
below the mark in a legible font.
Reserved for the official European Regulatory Requirement mark
CAN ICES-3(X)/NMB-3(X) Reserved for the official Industry of Canada certification number
Reserved for official UK Regulatory Requirement mark
Reserved for the official RCM (Australian) mark
Reserved for the official European Waste Electrical and Electronics Equipment (WEEE)
mark
Reserved for the official TUV mark
Reserved for the official Underwriters Laboratories (UL) mark
Reserved for the official Morocco mark
Reserved for the official Korean Certification (KC) mark

In addition, the certification number assigned to this Micron product shall be listed near
the mark in a legible font
Example: MSIP-REM-MU2-MTFDDAKXXXXXX or R-R-MU2-MTFDXXXXXXXXX
Warning Hot Surface symbol
PSID: XXXXXXXX-XXXX-XXXX- PSID alphanumeric code

XXXX-XXXXXXXXXXXX

Country where the device is assembled, written in English; Micron uses:
“Made in Taiwan” for Taiwan origin product
Product of XXXXXXXX
“Assembled in USA” for US origin product
“Product of XXXX” for products of other origins
LN: XXXXXXXXXX Lot number for tracking the drive’s manufacturing data
This is listed as xxyyyyyzzz:
xx = 2 digits to denote manufacturing site
yyyyy = 5 digits to denote the kit number (randomly generated)
zzz = 3 digits denoting a sublot size (to provide greater resolution of manufacturing
information)
HALOGEN-FREE Halogen-free mark indicating that the drive meets the IPC low-halogen requirements
Drive’s capacity, product type, maximum interface rate, and security feature set (SED,
XXXXGB XXX XGb/s XXXX
Opal 2, FIPS, and so on, if applicable); Example: 512GB SATA 6 Gb/s SED
Drive serial number
Format: 12 characters: YYWWXXXXXXXX
SN: YYWWXXXXXXXX YY is the current year
WW is the current Micron workweek
XXXXXXXX is an eight digit hex (base 16 0–9. A–F) serial number
Drive serial number bar code data for item above (follows the Code 128 standard)
(The example shown is a representation, not an actual barcode)
PN: MTFDXXXXXXXXX- Drive part number
XXXXXXXXX
Drive part number bar code data for item above (follows the Code 128 standard)
(The example shown is a representation, not an actual barcode)
MTFDXXXXXXXXXX Micron model number
MDL:MTFDXXXXXXXXX
EUI-64:00A0750XXXXXXXX EUI-64 number
Applicable to select products, a yellow bar may or may not be present on the label edge
Yellow bar
and may indicate Gen4 product.
Figure 9: Micron Standard SATA/NVMe 2.5/U.x SSD Label Structures
XXXX 2.5
Model: MTFDXXXXXXXXXX F/W: XXXXXXXX
P/N: MTFDXXXXXXXX-XXXXXXXX
S/N: YYWW12345678
XXXXGB SATA 6Gb/s SED XV X.XA
L/N: XXXXXXXXXX HALOGEN FREE

Product of XXXXXXXX
PSID: XXXXXXXX-XXXX-XXXX-XXXXXXXXXXXXX
E320115 6 Gb/s
D33F63
R-R-MU2-MTFDXXXXXXXXX
www.micron.com RoHS
CAN ICES-3(X)/NMB-3(X)
XXXX U.X XXXXGB

XV XA GenX xX F/W: XXXXXXXX
SED
LN: XXXXXXXXXX NVMe MODEL: MTFDXXXXXXXXX
P N: MTFDXXXXXXXXX-XXXXXXXXX
E320115
D33F63
SN: YYWWXXXXXXXX RoHS
PRODUCT OF XXXXXXX
www.micron.com
R-R-MU2-MTFDXXXXXXXXX
PSID: XXXXXXXX-XXXX-XXXX-XXXX-XXXXXXXXXXXX
Not shown is the worldwide name assigned to Micron (as defined by IEEE), which may
or may not be present on the label. WWN: 500A0751XXXXXXXX
Figure 10: Micron Standard SATA/NVMe M.2 SSD Label Structures
XXXX M.2 F/W: XXXXXXXX

XXXXGB SATA XGb/s SED
L/N: XXXXXXXXXX ™
Model: MTFDXXXXXXXXX D33F63

RoHS
6 Gb/s
P/N: MTFDXXXXXXXXX-XXXXXXXXX
S/N: YYWW12345678
Product of XXXXXXX
E320115
www.micron.com R-R-MU2-MTFDXXXXXXXXX
X.XV X.XA HALOGEN FREE
XXXX XXXXGB XV XA FW: XXXXXXXX

GenX xX SED
PN:MTFDXXXXXXXXX-XXXXXXXXX EUI-64:00A0750XXXXXXXX
MDL: MTFDXXXXXXXXX SN:YYWWXXXXXXXX
R-R-MU2-MTFDXXXXXXXXX PRODUCT OF XXXXXXXXX
NVM expressTM Leopoldstrasse 250 Munich 80807 Germany
SSD (????) London Rd Bracknell RG12 2AA UK
XXXX XXXXGB M.2 XV XA NVMe GenX xX FW: XXXXXXXX

SED MODEL:MTFDHBAXXXXXX
LN:YYWWXXXXXXXX PN:MTFDHBAXXXXXX-XXXXXXXXX
R-R-MU2-MTFDHBAXXXXXX
SN:YYWWXXXXXXXX PRODUCT OF XXXXXXXX
EUI-64:00A0750XXXXXXXX NVM expressTM
PSID:XXXXXXXX-XXXX-XXXX-XXXX-XXXXXXXXXXXX
XXXX XXXXGB SED xxxx XXXXGB M.2 GenX xX

FW: XXXXXXX XV XA SED XV XA
PN:MTFDXXXXXXXXX-XXXXXXXXX LN: XXXXXXXXXX FW: XXXXXXX
MDL:MTFDXXXXXXXXX GenX xX R-R-MU2-MTFDXXXXXXXXX
PRODUCT OF XXXXXXXXX EUI-64:00A0750111235678
R-R-MU2-MTFDXXXXXXXXX MODEL:MTFDXXXXXXXXX
PSID: XXXXXXXX-XXXX-XXXX-XXX PN:MTFDXXXXXXXXX-XXXXXXXXX
SN:YYWW12345678
X-XXXXXXXXXXXX PRODUCT OF XXXXXXXXX
EUI-64:00A075011 NVM expressTM
1235678
SN:YYWW12345678 PSID:XXXXXXXX-XXXX-XX
XX-XXXX-XXXXXXXXXXXX
NVM expressTM Leopoldstrasse 250 Munich 80807 Germany
SSD (????) London Rd Bracknell RG12 2AA UK
Figure 11: Micron Standard NVMe E1.x SSD Label Structures
Example 1
XXXX XXXXGB E1.x XV XA XXXX GenX xX FW:XXXXXXX
SED MODEL:MTFDXXXXXXXXX
LN: XXXXXXXXXX PN:MTFDXXXXXXXXX-XXXXXXXXX
SN:YYWWXXXXXXXX D33F63
EUI-64:00A0750XXXXXXXXX RoHS
R-R-MU2-XXXXXXXXX
PRODUCT OF XXXXXXXX E320115
PSID:XXXXXXXX-XXXX-XXXX-XXXX-XXXXXXXXXXXX www.micron.com
Example 2
XXXX XXXXGB E1.x XV XA XXXX GenX xX FW:XXXXXXX
SED MODEL:MTFDXXXXXXXXX
LN: XXXXXXXXXX PN:MTFDXXXXXXXXX-XXXXXXXXX
SN:YYWWXXXXXXXX
EUI-64:00A0750XXXXXXXXX
R-R-MU2-XXXXXXXXX
PRODUCT OF XXXXXXXX
PSID:XXXXXXXX-XXXX-XXXX-XXXX-XXXXXXXXXXXX www.micron.com
Figure 12: MID/CERT Label Structure
D33F63
123456789 RoHS
www.micron.com
LPN: 562-500127 E320115
CAN ICES-3(Ba)/NMB-3(B)
WARRENTY VOID IF REMOVED
The MID/CERT label may be used as needed where an SSD label does not include regu-
latory marks. The printed label has a black background with the text and marks in white.
Figure 13: Embedded USB Label Structure
MTFDXXXXXXXXX-XXXXX
F/W: FWXXXXXX YYWW
MTFDXXXXXXXXX
Product of XXXXXXXX
E320115
www.micron.com
Labels for engineering samples

replace these logos with text:
ENGINEERING SAMPLE.
SD and microSD Label Information

Figure 14 shows a representative front label structure for our SD and microSD products.
Figure 16 shows the backside markings. The figures have designated “key notes” that
outline the details of each particular item.
Figure 14: Micron SD Label Structure
6
32 GB
2
5 4 3

1. Micron logo
2. Speed class rating
3. UHS speed class rating
4. UHS Rating
5. Type
6. Form factor
7. Capacity
Figure 15: Micron microSD Label Structure
7 3
6 5

1. Micron logo
2. Form factor
3. UHS speed class rating
4. UHS Rating
5. Type
6. Speed class rating
7. Capacity
Figure 16: Micron SD Backside Markings
12
2
1 3
XXXXXXXXXXXX-XXX 4
XXXXXXX-XX XXXX
6 MADE IN XXXXXX

1. Reserved for the official USA Federal Communications Commission (FCC) mark
2. Reserved for the official European Regulatory Requirement mark
3. Reserved for the official Japan VCCI mark
4. Micron part number
5. Lot number and date code
6. Country of origin
Figure 17: Micron microSD Backside Markings
12
2
1 3
XXXXXXXXXXXXXX 4
XXXXX-XXX-XXXXXX X 5
XXXXX 6
MADE IN XXXXXXX 7

1. Reserved for the official USA Federal Communications Commission (FCC) mark
2. Reserved for the official European Regulatory Requirement mark
3. Reserved for the official Japan VCCI mark
4. Manufacturing lot number
5. Internal assembly part number
6. Date code
7. Country of origin
Micron Packaging Labels
Micron Packaging Labels

Micron uses various packaging labels to enable quick identification of packaged
contents, provide a simple order verification method, and indicate inner-package mois-
ture levels. All labels are manufactured from matte-coated facestock or synthetic paper
and contain acrylic- or water-based adhesive. See CSN-16 for complete information on
all Micron packaging materials, including recyclable materials.
Master Container Labels

For all shipments, Micron uses standard bar code labels that conform to EIA Standard
556. The bar code labels enable customers to scan Micron containers for quick order
verification. Figure 19 on page 26 shows an example of the standard bar code label used
on master containers. Each box also carries its own bar code label (see the Individual
Packaging Labels section).
Bar Code Information

The following information appears on the master container labels only:
• (3S/4S) - PKG ID: Invoice or packing slip number
• (1P) - SPLR PROD ID: Reserved for individual customer requirements
• (Q) - QUANTITY: Number of parts in master container
• (K) - TRANS ID: Customer purchase order number
• (P) - CUST PART NO: If a customer part number is not designated, the Micron part
number will be printed
• (4L) - Origin: The country in which the product was made
Figure 18: Standard Master Container Shipping Label
Micron Technology, Inc. US01

For Company Name
8000 S. Federal Way
BOISE ID 83707–0006
USA COMPANY NAME
ADDRESS
CITY STATE/PROVINCE ZIP CODE
COUNTRY
WB # 638030055867 / 0087659818
Child W/B: 00821466
*************
Piece 1 of 1 PKG ID: 87659819A1
*************
PO #s XXXXXXXX XXXXXXXX
Individual Packaging Labels
Figure 19: Standard Master Container Bar Code Label
(3S) PKG ID: 417904839 Ship_To_Name

Address
City, ST ZIP Code
Country
(Q) QUANTITY: 2500 (4L) Origin PACKAGE COUNT: Micron Technology, Inc.
1 OF 1 1160 Exchange, Doc 1D
TW 25.9 x 15.0 x 27.9 In Boise ID 83715
66.3 x 38.6 x 71.4 Cm USA
(1P)SPLR PROD ID: MT41K256M16TW
(K) TRANS ID: 4505469156
(P) CUST PART NO: 256-4839
PACKAGE WEIGHT 2.7 LBS / 1.2 KGS SHIP DATE 03/20/2017
Notes: 1. For the "CUST PART NO:" field, if no CPN is provided by the customer, the Micron part num-
ber will be displayed.
Additional Label Information

The following information appears in the upper right and bottom portion of the master
container labels and may differ slightly depending on whether the label has a (3S) or (4S)
PKG ID:
• Ship-to name: Customer’s name and ship-to address
• Ship-from name: Micron’s name and address
• PACKAGE COUNT (3S): Master container package count, or
TOTAL COUNT (4S): Master container package count
– (3S) label includes master container size in inches and centimeters
• PACKAGE WEIGHT (3S): Package weight in pounds and kilograms, or
TOTAL WEIGHT (4S): Master container weight in pounds and kilograms
• SHIP DATE: Date the product leaves the factory

For quick order verification, Micron attaches a standard bar code label and inner
packing container label on the inner packing container. Additionally, the moisture-
barrier or static-shielding bag has a moisture sensitivity (MST) label and a standard bar
code label attached to the front. If ordering in tape and reel, the tape-and-reel carrier
will have a standard bar code label attached. Figure 20 on page 27 shows an example of
the standard bar code label, Figure 21 on page 27 shows an example of Micron’s inner
packing container label, and Figure 23 on page 28 shows an example of Micron’s MST
label. Refer to Figure 24 on page 28 for approximate placement of these labels on
Micron’s moisture-barrier and static-shielding bags.
Figure 20: Standard Bar Code Label
PART NUMBER: (1P) MT48LC32M16A2TG –75:C
QUANTITY: 1000
DATE: 201532 235C MST: 3
(1T)BY5MGBV .21 260C MST: 3
Figure 21, Micron’s Inner Packing Container Label, indicates the RoHS status of compli-
ance with either RoHS or RoHS and HF (for those products that are also free of halo-
gens). This space will be blank on labels for containers that hold parts with lead. Also, an
asterisk (*) at the end of the date code indicates that the container holds a mix of product
from more than one date; the date shown is that of the oldest product in the container.
The “VID...” text is printed on the label as applicable for specific products.
Figure 21: Micron’s Inner Packing Container Label
ti
C au on
BY8MMHS.21 B
e
Origin Singapore
tiv
M
oi
For EU: Circuits Diffused in U.S. stur ensi
e- S
RoHS/HF 106558
QTY: 1000 (9D) 201510
V ID
D 01
1 01
1 QA
A 04
4 00
MT29F8G08ABABAWP:B
Figure 22: Micron’s Inner Packing Container Label for Modules and SSDs
BO Leopoldstrasse 250
Munich 80807 Germany
London Rd Bracknell
RG12 2AA UK
FH118GS.RQ Origin China FAB 6

MOD RoHS
QTY: 100 (9D) 201944 HT 135789
L
MT18KSF51272PDZ — 1G6K1FG
Notes: 1. The European Regulatory Requirement mark may or may not be present on a particular
inner packing label.
2. Some module product labels may include additional characters after the Micron marketing
part number. For more information, see the Module Label Data section.
Figure 23: Micron’s Moisture Sensitivity (MST) Label
235C Peak Package Body Temp Moisture Level: 2

Floor Life: One Year Condition < = 30 deg. C/60% RH
260C Peak Package Body Temp Moisture Level: 2

Floor Life: One Year Condition < = 30 deg. C/60% RH
Package Seal Date: Apr 08 2004
Operator: JDOE
Figure 24: Labeling on Moisture-Barrier and Static-Shielding Bags1
Heat-sealed
moisture-barrier bag
ESD and moisture precautions
Internal label2
MST label with moisture level,

floor life, and package seal date3
Standard bar code label4
Notes: 1. This figure indicates the approximate locations only of the various labels.
2. Internal labels are applicable to tube and tray shipments only and may or may not be pres-
ent on every bag.
3. See Figure 23.
4. See Figure 20.
Revision History
Revision History
Rev. AU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12/22
• Updated Table 5
Rev. AT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6/22

• Updated Figure 20
Rev. AS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3/22
• Updated Table 5
Rev. AR. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1/22

• Updated Table 5
Rev. AQ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11/21
• Updated Table 5
• Updated Figures 4 through 7
• Updated SSD section Figures and text
Rev. AP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7/21

• Updated Tables 2, 3 and 6
• Updated Figures 4, 5 and 7
• Removed DDR5 NVDIMM section
Rev. AO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1/21
Rev. AN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1/21
• Added Figure 4, Figure 5
• Updated Figure 6, Figure 7, Figure 8, Figure 21
• Added Table 5
• Removed figures: 2.5-inch Label Structure - M5XX(DC/IT)/M600 and
mSATA Label Structure - M6XX and mSATA Label Structure - M6XX
Rev. AM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9/19
• Updated Table 5
Rev. AL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4/19
• Updated country of origin key note text for Figures 4, 6, 8, 9, 10 and 11
• Added “Reserved for the official Industry of Canada certification number” to Figure 8
key notes
• Updated Figure 18 1P and P fields and added note 1
• Updated Figure 21 and added note 2
Rev. AK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11/18
• Updated Figure 5 and notes
• Updated Table 5
• Updated Figures 8, 10, 18 and 20
Rev. AJ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8/18
• Added note 2 to Figure 2
• Added the official Morocco mark to Figures 8 and 10
Revision History
Rev. AI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3/18
• Updated Tables 2 and 3
Rev. AH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12/17
• Added SD and microSD Label Information
Rev. AG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10/17
• Updated Figures 8–11
Rev. AF. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7/17

Rev. AE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5/17

• Updated Data matrix (2D) barcode description for Figure 10
• Deleted Figures 11 and 12 (EoL product)
Rev. AD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3/17
• Updated Figure 16 and the following explanatory paragraphs
Rev. AC. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11/16

• Added Table of Contents and List of Figures
• Updated Figures 1 and 2
• Updated and expanded Module Label Data and Examples (Added Process Codes )
• Updated all SSD labels and key note definitions
• Updated Figures 15 through 19
Rev. AB. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5/16

• Added DDR3, DDR4 Process Code Reference section
Rev. AA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3/16

• Corrected typo in Note 3 of Figure 4
• Updated Figures 12, 16 and added new Figure 17. 1/16
Rev. Z . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10/15
• Updated module label explanation and notes.
• Added M6xx SSD labels.
• Deleted links to specific SSD label figures under SSD Label Information.
• Added Table of Contents and List of Figures.
• Updated Figure 2 title.
Rev. Y . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7/15
• Added SSD MID label.
Rev. X . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5/15
• Updated Figure 4.
• Updated Figure 23.
Rev. W . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5/15
• Added Note 2 to Figure 4.
Rev. V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10/14
• Updated information on page one.
• Added information for legacy components with Elpida part marks.
• Added DC and IT mark to M5xx SSD label title.
Revision History
• Added 2.5in P420m label information.
Rev. U. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7/14
• Added M.2 M510/M550 label.
Rev. T . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1/14
• Added “.../date code (YWW)” to Line 1 of the Module Label Information section.
Rev. S . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12/13
• Added European Regulatory Requirement logo and note to Figures 3 and 20.
• Corrected numbering on pages 4 and 5.
Rev. R . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8/13
• Corrected label titles for Figure 10, Figure 16, and Figure 17.
Rev. R . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7/13
• Added new SSD labels.
Rev. Q. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5/13
• Added new SSD labels.
Rev. P . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2/13
• Updated Inner Packing Container and Standard Master Container Shipping labels.
• Corrected note references for Figure 15.
Rev. O. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6/12
• Added Microdisplay panel label.
Rev. N. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3/12
• Added the Embedded USB label.
Rev. M . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2/12
• Added the SSD mSATA label.
Rev. L . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2/12
• Corrected references in Figure 12.
Rev. K . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10/11
• Updated security feature set to Figure 6 and it’s notes.
Rev. J . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6/11
• Added aliases to the links for the part numbering guides and FBGA date codes, and
the FBGA Part Marking Decoder.
• Added specific date code information.
• Updated country codes.
• Added SSD C400 label information.
Rev. H. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2/10
• Added date code information to the text for Figure 9
Rev. G . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1/10
• Corrected typo
Rev. F . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12/09
• Added SSD product labels
• Added packaging label information from CSN-16
Revision History
Rev. E . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10/09
• Updated template
• Updated Figure 3, “Module Label”
Rev. D. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6/08
• Added Korea to note 1 country codes
• Updated and renamed Figure 2
• Deleted Figure 3, “DDR2/GDDR3 FBGA Abbreviated Component Mark”
Rev. C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5/07
• Added Taiwan to note 1 country codes
Rev. 12/9/05
• Added logo information to Figure 1 on page 6 and Figure 2 on page 7
Rev. 2/14/05
• Added China to note 1 country code
8000 S. Federal Way, P.O. Box 6, Boise, ID 83707-0006, Tel: 208-368-3900

www.micron.com/productsupport Customer Comment Line: 800-932-4992
Micron and the Micron logo are trademarks of Micron Technology, Inc.
All other trademarks are the property of their respective owners.

Micron csn11

Uploaded by

Copyright:

Available Formats

Micron csn11

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Micron csn11

Uploaded by

Copyright:

Available Formats

CSN-11: Product Marks/Product and Packaging Labels

Customer Service Note

Product Marks and Labels

Component Mark Information

Figure 1: TSOP Component Mark

Abbreviated Component Mark Information

More information on product-specific designators is provided in Micron’s various part

Figure 2: SOP2/W-PDFN/BGA/LGA Abbreviated Component Mark

Product Coded part number

Function mark Special mark

Figure 3: Legacy BGA Component with Elpida Part Mark

Module Label Data and Examples

Key note definitions:

12. Module DIMM type

Key note definitions:

10e. Module serial number, eight characters, unique to each module

Figure 6: DDR4/DDR3 NVDIMM Additional Label Content

Figure 7: DDR4/DDR3 ECC UDIMM/SODIMM Label Example

Key note definitions:

– "Made in Taiwan" for Taiwan origin product

Table 1: DDR3 Process Code Options

Table 2: DDR4 RDIMM, NVDIMM1 Process Code Options

RCD Vendor Temp Sensor/ Temp Sensor/

Table 3: DDR4 LRDIMM Process Code Options

Table 4: DDR4 NVDIMM Process Code Third Character Options

MUX Vendor Process Code Character Vendor Part Number

Table 5: DDR5 Process Code Options

Table 6: Module Manufacturing Locations

Location ID Number Hexadecimal Value

SSD Label Information

Figure 8: SSD MID Label

Table 7: SSD Label Mark Definitions

Mark or Text Example Definitions

Reserved for the official China Restriction of Hazardous Substances mark

Reserved for the official Japan VCCI mark

Table 7: SSD Label Mark Definitions

Mark or Text Example Definitions

Reserved for the official European Regulatory Requirement mark

Reserved for the official RCM (Australian) mark

Reserved for the official TUV mark

Reserved for the official Underwriters Laboratories (UL) mark

Reserved for the official Morocco mark

Reserved for the official Korean Certification (KC) mark

PSID: XXXXXXXX-XXXX-XXXX- PSID alphanumeric code

Table 7: SSD Label Mark Definitions

Mark or Text Example Definitions

Figure 9: Micron Standard SATA/NVMe 2.5/U.x SSD Label Structures

L/N: XXXXXXXXXX HALOGEN FREE

XXXX U.X XXXXGB

LN: XXXXXXXXXX NVMe MODEL: MTFDXXXXXXXXX

Figure 10: Micron Standard SATA/NVMe M.2 SSD Label Structures

XXXX M.2 F/W: XXXXXXXX

Model: MTFDXXXXXXXXX D33F63

XXXX XXXXGB XV XA FW: XXXXXXXX

XXXX XXXXGB M.2 XV XA NVMe GenX xX FW: XXXXXXXX

XXXX XXXXGB SED xxxx XXXXGB M.2 GenX xX

Figure 11: Micron Standard NVMe E1.x SSD Label Structures

Figure 12: MID/CERT Label Structure

Figure 13: Embedded USB Label Structure