IFE Maksimalafbryder Ethernet Gateway

IFE Ethernet Interface for LV Circuit Breakers
DOCA0084EN 03/2014
IFE Ethernet Interface for LV

Circuit Breakers
User Guide
03/2014
DOCA0084EN-00
www.schneider-electric.com
The information provided in this documentation contains general descriptions and/or technical character-
istics of the performance of the products contained herein. This documentation is not intended as a
substitute for and is not to be used for determining suitability or reliability of these products for specific user
applications. It is the duty of any such user or integrator to perform the appropriate and complete risk
analysis, evaluation and testing of the products with respect to the relevant specific application or use
thereof. Neither Schneider Electric nor any of its affiliates or subsidiaries shall be responsible or liable for
misuse of the information contained herein. If you have any suggestions for improvements or amendments
or have found errors in this publication, please notify us.
No part of this document may be reproduced in any form or by any means, electronic or mechanical,
including photocopying, without express written permission of Schneider Electric.
All pertinent state, regional, and local safety regulations must be observed when installing and using this
product. For reasons of safety and to help ensure compliance with documented system data, only the
manufacturer should perform repairs to components.
When devices are used for applications with technical safety requirements, the relevant instructions must
be followed.
Failure to use Schneider Electric software or approved software with our hardware products may result in
injury, harm, or improper operating results.
Failure to observe this information can result in injury or equipment damage.
© 2014 Schneider Electric. All rights reserved.
2 DOCA0084EN 03/2014
Table of Contents
Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
About the Book. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Chapter 1 IFE Presentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
IFE Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Customer Engineering Tool. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
IFE Schematics With Masterpact NT/NW and Compact NS Circuit Breakers. . . . . . . . . . . . 19
IFE Schematics With Compact NSX Circuit Breakers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
IFE Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
IFE Firmware Update . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Protecting the Environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Chapter 2 IFE Web Server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
2.1 IFE Ethernet Interface for LV Circuit Breaker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Access to IFE Web Pages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
IFE User Interface Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
IFE Web Page Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
2.2 IFE Web Server - Setup Pages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Device Localization/Name . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Device Name . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Ethernet Configuration (Dual Port) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
IP Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Modbus TCP/IP Filtering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Serial Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Date and Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
E-mail Server Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Alarms to Be E-mailed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Device List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Device Logging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Device Log Export . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
SNMP Parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Documentation Links . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Preferences . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Advanced Services Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
User Accounts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Web Page Access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
2.3 IFE Web Server - Monitoring Pages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Real Time Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Device Logging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
2.4 IFE Web Server - Control Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Single Device Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
2.5 IFE Web Server - Diagnostics Pages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Statistics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Device Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
IMU Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Read Device Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
Communication Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
2.6 IFE Web Server - Maintenance Pages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
Maintenance Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Maintenance Counters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
Appendices ...................................................... 79
Appendix A Appendix A - List of IFE Supported Devices . . . . . . . . . . . . . . . . . . . . . . 81
List of IFE Supported Device Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
DOCA0084EN 03/2014 3
4 DOCA0084EN 03/2014
Safety Information
Important Information
NOTICE
Read these instructions carefully, and look at the equipment to become familiar with the device before
trying to install, operate, or maintain it. The following special messages may appear throughout this
documentation or on the equipment to warn of potential hazards or to call attention to information that
clarifies or simplifies a procedure.
PLEASE NOTE
Electrical equipment should be installed, operated, serviced, and maintained only by qualified personnel.
No responsibility is assumed by Schneider Electric for any consequences arising out of the use of this
material.
A qualified person is one who has skills and knowledge related to the construction and operation of
electrical equipment and its installation, and has received safety training to recognize and avoid the
hazards involved.
DOCA0084EN 03/2014 5
6 DOCA0084EN 03/2014
About the Book
At a Glance
Document Scope
The aim of this document is to provide the users, installers, and the maintenance personnel with the
technical information and procedure needed to access and maintain the IFE web server.
Validity Note
The technical characteristics of the devices described in this document also appear online. To access this
information online:
Step Action
1 Go to the Schneider Electric home page www.schneider-electric.com.
2 In the Search box type the reference of a product or the name of a product range.
z Do not include blank spaces in the model number/product range.
z To get information on grouping similar modules, use asterisks (*).
3 If you entered a reference, go to the Product datasheets search results and click on the
reference that interests you.
If you entered the name of a product range, go to the Product Ranges search results and click
on the product range that interests you.
4 If more than one reference appears in the Products search results, click on the reference that
interests you.
5 Depending on the size of your screen, you may need to scroll down to see the data sheet.
6 To save or print a data sheet as a .pdf file, click Download XXX product datasheet.
The characteristics that are presented in this manual should be the same as those characteristics that
appear online. In line with our policy of constant improvement, we may revise content over time to improve
clarity and accuracy. If you see a difference between the manual and online information, use the online
information as your reference.
Related Documents
Title of Documentation Reference Number

IFE Ethernet Interface for LV Circuit Breaker - Instruction Sheet HRB49218
Masterpact NT/NW, Compact NS Modbus Communication Guide DOCA0054 (FR)
DOCA0054 (EN)
DOCA0054 (ES)
Compact NSX Modbus Communication Guide LV434106 (FR)
LV434107 (EN)
LV434108 (ES)
ULP System - User Guide TRV99100 (FR)
TRV99101 (EN)
TRV99102 (ES)
You can download these technical publications and other technical information from our website at
www.schneider-electric.com.
DOCA0084EN 03/2014 7
8 DOCA0084EN 03/2014
IFE Presentation
DOCA0084EN 03/2014
IFE Presentation
Chapter 1
IFE Presentation
What Is in This Chapter?

This chapter contains the following topics:
Topic Page
IFE Description 10
Customer Engineering Tool 17
IFE Schematics With Masterpact NT/NW and Compact NS Circuit Breakers 19
IFE Schematics With Compact NSX Circuit Breakers 24
IFE Characteristics 28
IFE Firmware Update 29
Protecting the Environment 30
DOCA0084EN 03/2014 9
IFE Presentation
IFE Description
Introduction
The IFE Ethernet interface for LV circuit breaker enables an intelligent modular unit (IMU), for example a
Masterpact NT or Compact NSX circuit breaker to be connected to an Ethernet network. Each circuit
breaker has its own IFE and a corresponding IP address.
Types of IFE
There are 2 commercial references of the IFE:
z LV434010 - Ethernet interface for LV circuit breaker
This type of IFE is an Ethernet interface for Compact, PowerPact, and Masterpact circuit breakers.
z LV434011 - Ethernet interface for LV circuit breaker and gateway
This type of IFE is an Ethernet interface for Compact, PowerPact, and Masterpact circuit breakers and
a gateway for Modbus-SL (serial line) connected devices.
IFE Features
The main features of IFE are:
z Dual Ethernet port for simple daisy chain connection
z Device profile web service for discovery of the IFE on the local area network (LAN)
z ULP compliant for localization of the IFE in the switchboard
z Ethernet interface for Compact, PowerPact, and Masterpact circuit breakers
z Gateway for Modbus-SL connected devices (only for the IFE with the commercial reference LV434011)
z Embedded set-up web pages
z Embedded monitoring web pages
z Embedded control web pages
z Built-in e-mail alarm notification
NOTE: IFE in-built switch does not support the ring topology as it does not have the feature of the loop
back protection.
Intelligent Modular Unit

A modular unit is a mechanical and electrical assembly containing one or more products to perform a
function in a switchboard (incoming protection, motor command, and control). The modular units are easily
installed in the switchboard.
The circuit breaker with its internal communicating components (Micrologic and so on) and external ULP
modules (FDM121, IO module, and so on) connected to one IFM or IFE communication interface is called
an intelligent modular unit (IMU).
10 DOCA0084EN 03/2014
IFE Presentation
Communication Architecture
A FDM121 display for LV circuit breaker

B IFE Ethernet interface for LV circuit breaker and gateway
C IFE Ethernet interface for LV circuit breaker
D IFM Modbus-SL interface for LV circuit breaker
E IO input/output interface module for LV circuit breaker
F Masterpact NT/NW circuit breaker
G Compact NS circuit breaker
H Compact NSX circuit breaker
I ULP termination
J ULP cable
K Circuit breaker ULP cord
L NSX cord
DOCA0084EN 03/2014 11
IFE Presentation
Connection Accessories
The below table lists the part numbers for the components of the ULP system for the circuit breaker:
Product Description Part Number

Breaker ULP cord L = 0.35 m (1.15 ft) LV434195
L = 1.3 m (4.26 ft) LV434196
L = 3 m (9.84 ft) LV434197
Cord for system voltage greater than 480 Vac L = 1.3 m (4.26 ft), U > 480 Vac LV434204
(cord with female socket)
BCM ULP breaker communication module – 33106
IO input/output interface for LV circuit breaker – LV434063
FDM121 display for LV circuit breaker – TRV00121
Surface-mounting accessory – TRV00128
IFM Modbus-SL interface for LV circuit breaker – TRV00210
IFE Ethernet interface for LV circuit breaker Ethernet interface LV434010
Ethernet interface and gateway LV434011
Stacking accessory 10 stacking accessories TRV00217
Maintenance module – TRV00911
ULP cable L = 0.3 m (0.98 ft), 10 cables TRV00803
L = 0.6 m (1.97 ft), 10 cables TRV00806
L = 1 m (3.28 ft), 5 cables TRV00810
L = 2 m (6.56 ft), 5 cables TRV00820
L = 3 m (9.84 ft), 5 cables TRV00830
L = 5 m (16.40 ft), 1 cable TRV00850
RJ45 female/female connector 10 RJ45 female/female connectors TRV00870
ULP line terminator 10 ULP terminators TRV00880
Modbus line terminator 2 Modbus cable terminators with VW3A8306DRC
impedance of 120 Ω + 1 nF
24 Vdc power supply 24/30 Vdc-24 Vdc-1 A-overvoltage 54440
category IV
48/60 Vdc-24 Vdc-1 A-overvoltage 54441
category IV
100/125 Vdc-24 Vdc-1 A-overvoltage 54442
category IV
110/130 Vac-24 Vdc-1 A-overvoltage 54443
category IV
category IV
category IV
100/500 Vac-24 Vdc-3 A-overvoltage ABL8RPS24030
category II
Modbus cable Belden: 7 mm (0.27 in.) diameter 3084A
shielded cable with 2 twisted pairs
Belden: 9.6 mm (0.38 in.) diameter 7895A
(recommended) shielded cable with 2
twisted pairs
Cable with 2 twisted pairs without 50965
shielding drain wire
2-wire RS 485 isolated repeater module - TRV00211
NSX cord L = 0.35 m (1.15 ft) LV434200
L = 1.3 m (4.27 ft) LV434201
L = 3 m (9.84 ft) LV434202
12 DOCA0084EN 03/2014
IFE Presentation
Description
A Ethernet 1 and Ethernet 2 communication port

B 24 Vdc power supply terminal block
C Ethernet communication LEDs
D Module status LED
E Network status LED
F Sealable transparent cover
G Reset button
H ULP status LED
I Test button (accessible cover closed)
J Locking pad
K Modbus traffic status LED (IFE gateway only)
L Device name label
M ULP ports
Mounting
The IFE mounts on a DIN rail. The stacking accessory enables the user to connect several IFMs to an IFE
gateway without additional wiring.
NOTE: The stacking feature is available only for the IFE with the commercial reference LV434011.
DOCA0084EN 03/2014 13
IFE Presentation
24 Vdc Power Supply

The IFE must be always supplied with 24 Vdc. The IFMs stacked to an IFE gateway are supplied by the
IFE gateway and it is not necessary to supply them separately.
It is recommended to use an UL listed and recognized limited voltage/limited current or a class 2 power
supply with a 24 Vdc, 3 A maximum.
Ethernet Communication LEDs

The Ethernet communication dual color LEDs, indicate the status of the Ethernet ports ETH1 and ETH2.
LED Indication Status Description

OFF No power or no link
Steady yellow 10 Mbps, link established, and no activity
Blinking yellow 10 Mbps, ongoing activity
Steady green 100 Mbps, link established, and no activity
Blinking green 100 Mbps, ongoing activity
Module Status LED

The module status dual color LED, indicates the IFE status.

OFF No power
Steady green IFE operational
Blinking green (250 ms ON, 250 ms OFF) Hidden control web page available
Blinking green (500 ms ON, 500 ms OFF) IFE Firmware corrupted
Blinking red (500 ms ON, 500 ms OFF) IFE in degraded mode
Steady red IFE out of service
Blinking green/red (1 s green, 1 s red) Firmware upgrade in progress
Blinking green/red (250 ms green, 250 ms red) Self test in progress
14 DOCA0084EN 03/2014
IFE Presentation
Network Status LED

The network status dual color LED, indicates the Ethernet network status.

OFF No power or no IP address
Steady green Valid IP address
Steady red Duplicated IP address
Blinking green/red (250 ms green, 250 ms red) Self test in progress
Steady amber Error in IP configuration
Modbus Serial Line Traffic LED

The Modbus serial line traffic yellow LED, indicates that the traffic is being transmitted or received over the
Modbus serial line network through the IFE gateway.
The LED is ON during the transmission and reception of the messages; otherwise LED is OFF.
NOTE: The LED is OFF on IFE without gateway feature (commercial reference LV434010).
Modbus Address
The IFE accepts the Modbus address of the intelligent modular unit (IMU) to which it is connected.
The Modbus address is 255 and cannot be changed.
Locking Pad
The locking pad on the front panel of the IFE, enables or disables to send the remote control commands
over the Ethernet network to the IFE, and to the other modules of the connected IMU.
z If the arrow points to the open padlock (factory setting), remote control commands are enabled.
z If the arrow points to the closed padlock, remote control commands are disabled.
The only remote control command that is enabled even if the arrow points to the closed padlock is the
set absolute time command.
Test Button
The test button has two functions, according to the duration of the button pressed.
Time Range Function

1–5 s Tests the connection between all the ULP modules for 15 seconds.
10–15 s Activates the hidden configuration mode for 5 minutes.
Reset Button
When the reset button is pressed for 1–5 seconds, it forces the IP acquisition mode to the factory default
setting (DHCP).
DOCA0084EN 03/2014 15
IFE Presentation
ULP LED
The yellow ULP LED describes the mode of the ULP module.
ULP LED Mode Action

Nominal None
Conflict Remove extra ULP module
Degraded Replace ULP module at the

next maintenance operation
Test None
Non-critical firmware Upgrade firmware at the next

discrepancy maintenance operation
Non-critical hardware Replace ULP module at the
discrepancy next maintenance operation
Configuration discrepancy Install missing features
Critical firmware discrepancy Upgrade firmware
Critical hardware discrepancy Replace ULP module
Stop Replace ULP module
Power OFF Check power supply
16 DOCA0084EN 03/2014
IFE Presentation
Customer Engineering Tool
Definition
The customer engineering tool used to configure the IFE Ethernet interface for LV circuit breaker is
Electrical Asset Manager software or:
z Compact NSX RSU software
z to update the IFE firmware
z to manage the passwords
z to set date and time.
z Masterpact RSU software to configure the Masterpact pre-defined alarm.

z RCU software to check the network communication with IFE.
The customer engineering tools are available at www.schneider-electric.com.
Electrical Asset Manager

Electrical Asset Manager software enables the user to have the following features in addition to the
features provided by Compact NSX RSU, Masterpact RSU, and RCU software:
z create projects by device discovery, selection of devices from Schneider Electric catalogue and
importing Bill Of Material (BOM) files
z monitor the status of protection and IO status
z read information (alarms, measurements, parameters)
z check protection discrimination between two devices
z upload and download of configuration or settings in batches
z performs control actions in a secured way
z generate and print device settings report and communication test report
z manage multiple devices with electrical and communication hierarchy model
z manage artifacts (project and device documents)
z check consistency in settings between devices in a communication network
z compare configuration settings between the project and device (online)
z download latest firmware and upgrade devices
z safe repository of projects in Schneider Electric Cloud and Sharing of projects with other users
For more information, see the Electrical Asset Manager Online Help.
Compact NSX RSU Software

Compact NSX RSU (Remote Setting Utility) is the Compact NSX configuration software. It enables the
user to:
z check and set up the Micrologic trip unit parameters:
z protection parameters
z measurement parameters
z alarm parameters.
z display the Micrologic tripping curves.

z check and set up the SDx module output parameters.
z check the SDTAM module output parameters.
z check and set up the Breaker Status and Control Module (BSCM) parameters.
z edit and save configurations.
Compact NSX RSU can also be used to configure the intelligent modular unit (IMU) modules connected to
Compact NSX, Compact NS, or Masterpact circuit breakers, and enables the user to:
z check and set up the IFM parameters.
z check and set up the IFE parameters.
z modify passwords in the IMU.
z change IMU identification.
z get and set the time.
z configure the IO assignments.
z modify the IO counters.
z reset the IO counters (only with Schneider service user profile).
z update firmware of ULP (Universal Logic Plug) modules (only with Schneider service user profile).
z reset the passwords to their factory values (only with the Schneider service user profile.)
z reset the IO module settings to their factory values (only with the Schneider service user profile.)
For more information, see the Compact NSX RSU Online Help.
DOCA0084EN 03/2014 17
IFE Presentation
Masterpact RSU Software

Masterpact RSU (Remote Setting Utility) is the Masterpact and Compact NS configuration software.
Masterpact RSU enables the user to:
z check and set up the Micrologic trip unit parameters:
z protection parameters
z measurement parameters
z alarm parameters.
z display the Micrologic tripping curves.

For more information, see the Masterpact RSU Online Help.
RCU Software
RCU (Remote Control Utility) is a simple SCADA software for:
z Compact NSX circuit breakers
z Compact NS circuit breakers
z Masterpact circuit breakers
z Power meters
Depending on the equipment the RCU software is connected to, RCU enables the user to:
z display the measurements of I, U, E, THD.
z display the date and time.
z display the identification and maintenance information of the equipment.
z control the equipment (only for circuit breakers).
z log the measurements P, FP, E every 5 minutes.
z display the status of the IOs.
z check the network communication with IFM or IFE.
The RCU software helps the users to monitor and control their equipment and helps the installers to check
and validate the newly installed equipment.
For more information, see the RCU Online Help.
18 DOCA0084EN 03/2014
IFE Presentation
IFE Schematics With Masterpact NT/NW and Compact NS Circuit Breakers
Description
Depending on the type of circuit breaker used, connect the IFE Ethernet interface for LV circuit breaker to
the circuit breaker using one of the following configurations:
z Connection of the IFE to a fixed manually-operated Compact NS circuit breaker with a BCM ULP.
z Connection of the IFE to a fixed electrically-operated Masterpact NT/NW or Compact NS 630b-1600
circuit breaker with a BCM ULP.
z Connection of the IFE to a drawout Masterpact NT/NW or Compact NS 630b-1600 circuit breaker with
a BCM ULP and its respective IO input/output interfaces for LV circuit breakers.
ULP Connection
NOTICE
HAZARD OF EQUIPMENT DAMAGE
z The IFE RJ45 ports are for ULP modules only.
z Any other use can damage the IFE or the device connected to the IFE.
z To check if a ULP module is compatible with the IFE’s RJ45 ports, refer to the ULP System User
Guide.
Failure to follow these instructions can result in equipment damage.
All connection configurations require the breaker ULP cord. The insulated NSX cord is mandatory for
system voltages greater than 480 Vac.
When the second ULP RJ45 connector is not used, it must be closed with a ULP terminator.
DOCA0084EN 03/2014 19
IFE Presentation
Connection of the IFE to a Fixed Manually-Operated Compact NS Circuit Breaker

Connect the IFE to a fixed manually-operated Compact NS circuit breaker using the breaker ULP cord:
A IFE Ethernet interface for LV circuit breaker

B Breaker ULP cord
C BCM ULP breaker communication module
D Fixed manually-operated Compact NS circuit breaker
20 DOCA0084EN 03/2014
IFE Presentation
Connection of the IFE to a Fixed Electrically-Operated Masterpact NT/NW or Compact NS 630b-1600 Circuit Breaker
Connect the IFE to a fixed electrically-operated Masterpact NT/NW or Compact NS 630b-1600 circuit
breaker using the breaker ULP cord:

B Breaker ULP cord
C Fixed terminal block
D BCM ULP communication module
E Fixed electrically-operated circuit breaker
DOCA0084EN 03/2014 21
IFE Presentation
Connection of the IFE to a Drawout Masterpact NT/NW or Compact NS 630b-1600 Circuit Breaker
Connect the IFE to a drawout Masterpact NT/NW or Compact NS 630b-1600 circuit breaker using the
breaker ULP cord:

B ULP cable
C Breaker ULP cord
D Circuit breaker disconnected position contact (CD)
E Circuit breaker cradle
F BCM ULP breaker communication module
G Drawout circuit breaker
H Drawout terminal block
I Circuit breaker connected position contact (CE)
J Circuit breaker test position contact (CT)
K IO input/output interface for LV circuit breaker
22 DOCA0084EN 03/2014
IFE Presentation
Connection of the IFE to a Masterpact NT/NW or Compact NS Circuit Breaker for System Voltage Greater Than 480 Vac
The following figure presents a fixed electrically-operated Masterpact NT/NW or Compact NS circuit
breaker using the insulated NSX cord:

B ULP cable
C Insulated ULP module for system voltage greater than 480 Vac
D Insulated ULP cord for system voltage greater than 480 Vac
E Fixed terminal block
F BCM ULP breaker communication module
G Fixed electrically-operated circuit breaker
DOCA0084EN 03/2014 23
IFE Presentation
IFE Schematics With Compact NSX Circuit Breakers
General Description
Depending on the configuration of the Compact NSX circuit breaker, connect the IFE Ethernet interface for
LV circuit breaker to the circuit breaker using one of the following configurations:
z connection of the IFE to the Micrologic trip unit
z connection of the IFE to the BSCM (Breaker Status and Control Module)
z connection of the IFE to the BSCM and to the Micrologic trip unit
ULP Connection
NOTICE
HAZARD OF EQUIPMENT DAMAGE
z The IFE RJ45 ports are for ULP modules only.
z Any other use can damage the IFE or the device connected to the IFE.
z To check if a ULP module is compatible with the IFE’s RJ45 ports, refer to the ULP System User
Guide.
Failure to follow these instructions can result in equipment damage.
All the connection configurations require the NSX cord. The insulated NSX cord is mandatory for system
voltages greater than 480 Vac.
See the Compact NSX Circuit Breakers User manual for more information regarding the description and
mounting of the Compact NSX circuit breaker compliant products (Micrologic trip unit, BSCM, NSX Cord).
Connection of the IFE to the Micrologic Trip Unit

Connect the IFE to the Micrologic trip unit using the NSX cord:

B NSX cord
C Micrologic trip unit
24 DOCA0084EN 03/2014
IFE Presentation
Connection of the IFE to the BSCM

Connect the IFE to the BSCM using the NSX cord:

B NSX cord
C BSCM Breaker status and control module
DOCA0084EN 03/2014 25
IFE Presentation
Connection of the IFE to the BSCM and to the Micrologic Trip Unit
Connect the IFE to the BSCM and to the Micrologic trip unit using the NSX cord:

B NSX cord
C BSCM Breaker status and control module
D Micrologic trip unit
26 DOCA0084EN 03/2014
IFE Presentation
Connection of the IFE to a Circuit Breaker for System Voltage Greater Than 480 Vac
The following figure represents the same connection schematic but with the insulated NSX cord:

B ULP cable
C Insulated ULP module for system voltage greater than 480 Vac
D Insulated ULP cord for system voltage greater than 480 Vac
E Connector for Compact NSX internal connection
DOCA0084EN 03/2014 27
IFE Presentation
IFE Characteristics
Environmental Characteristics
Characteristic Value
Conforming to standards z IEC 60950
z IEC 60947-6-2
z UL508
z UL60950
Certification cULus, CE, and FCC marking

Ambient temperature Storage -40 to +85 °C (-40 to +185 °F)
Operation -25 to +70 °C (-13 to +158 °F)
Protective treatment ULV0, conforming to IEC/EN 60068-2-30
Pollution Level 3
Mechanical Characteristics
Shock resistance Conforming to IEC 60068-2-27
15 g/11 ms, 1/2 sinusoidal
Resistance to sinusoidal vibrations Conforming to IEC/EN 60068-2-6
Electrical Characteristics
Characteristics Value
Power supply 24 Vdc, -20%/+10% (19.2–26.4 Vdc)
Consumption Typical 24 Vdc, 120 mA at 20°C
Maximum with gateway 19.2 Vdc, 3 A at 60°C
Physical Characteristics
Dimensions 72 x 105 x 71 mm (2.83 x 4.13 x 2.79 in)
Mounting DIN rail
Weight 182.5 g (0.41 lb)
Degree of protection of the installed module z On the front panel (wall-mounted enclosure): IP4x
z Connectors: IP2x
z Other parts: IP3x
Connections Screw type terminal blocks
24 Vdc Power Supply Characteristics

It is recommended to use an UL listed/UL recognized limited voltage/limited current or a Class 2 power
supply with a 24 Vdc, 3 A maximum.
For more information, refer to the ULP System User Guide.
Power supply type Regulated switch type
Rated power 72 W
Input voltage 100–120 Vac for single phase
200–500 Vac phase-to-phase
PFC filter With IEC 61000-3-2
Output voltage 24 Vdc
Power supply output current 3A
28 DOCA0084EN 03/2014
IFE Presentation
IFE Firmware Update
Description
IFE consists of two types of components:
z The executable binary component
z The webpage and device supporting file (Data file)
The firmware on the IFE can be updated using:

z FTP
z Customer engineering tool
Executable Binary Component Firmware Version
Step Action Result

1 Open the web browser and log into the IFE. Opens the IFE home page.
2 Locate the firmware version on Device Information page on Determines the firmware version of the IFE.
the Diagnostics menu (see page 72).
NOTE: If you have updated the firmware recently, press F5 to
refresh the web page and update the displayed firmware
number.
Getting the Web Page and the Device Supporting Files
Step Action Result

1 Start the web browser, type www.schneider-electric.com in the Opens the www.schneider-electric.com website.
Address text box, then press Enter.
2 In the search box enter IFE_DataFiles, and then click the The IFE_DataFiles_Vx.y.z zip files will appear in the
search button. search result (where x.y.z is the datafile version number)..
3 Select the lastest version of the Datafiles, and then click the The Save As dialog box opens.
IFE_DataFiles_Vx.y.z zip file. to save the IFE data file in
the local directory.
4 Click Save As to store the IFE_DataFiles_Vx.y.z zip file in Saves the IFE_DataFiles_Vx.y.z zip in the desired
the desired location. location.
5 Click the IFE_DataFiles_Vx.y.z zip file to unzip and save Saves the IFE data file in the desired directory/folder.
in the desired location.
Updating the Web Pages and Device Supporting Files using FTP
Step Action Result

1 Start the web browser, type ftp://<device IP address> Starts the FTP session and prompts for user name and
in the Address text box, then press Enter. password.
2 Type Administrator as the user name and Gateway as the Succeeds login process and locates a directory wwwroot.
password in the text boxes, and then click Log On.
3 Upgrade the web page by: z Deletes the files from the directory.
z locating wwwroot directory. Delete all the files in wwwroot z Adds the new files from the PC to the directory.
directory. Drag and drop the new files from the wwwroot
folder of the newly saved IFE_DataFiles_Vx.y.z file.
z locating logging/templates directory. Delete all the files
in logging/templates directory. Drag and drop the new
files from the logging/templates folder of the newly
saved IFE_DataFiles_Vx.y.z file..
Updating the Executable Binary Component using the Customer Engineering Tool
For more information, refer to the Customer Engineering Tool Online Help.
DOCA0084EN 03/2014 29
IFE Presentation
Protecting the Environment
Recycling Packaging
The packing materials from this equipment can be recycled. Please help protect the environment by
recycling them in appropriate containers.
Thank you for playing your part in protecting the environment.
End-of-Life Recycling
At the end of life, the modules of the ULP system have been optimized to decrease the amount of waste
and valorize the components and materials of the product in the usual end of life treatment process.
The design has been achieved so as components are able to enter the usual end of life treatment
processes as appropriate: depollution if recommended, reuse and/or dismantling if recommended so as to
increase the recycling performances and shredding for separating the rest of materials.
30 DOCA0084EN 03/2014
IFE Web Server
DOCA0084EN 03/2014
IFE Web Server
Chapter 2
IFE Web Server
What Is in This Chapter?

This chapter contains the following sections:
Section Topic Page
2.1 IFE Ethernet Interface for LV Circuit Breaker 32
2.2 IFE Web Server - Setup Pages 40
2.3 IFE Web Server - Monitoring Pages 61
2.4 IFE Web Server - Control Page 67
2.5 IFE Web Server - Diagnostics Pages 69
2.6 IFE Web Server - Maintenance Pages 76
DOCA0084EN 03/2014 31
IFE Web Server
IFE Ethernet Interface for LV Circuit Breaker
Section 2.1
IFE Ethernet Interface for LV Circuit Breaker
What Is in This Section?

This section contains the following topics:
Topic Page
Access to IFE Web Pages 33
IFE User Interface Layout 36
IFE Web Page Description 38
32 DOCA0084EN 03/2014
IFE Web Server
Access to IFE Web Pages
Supported Web Browsers
Browser Version with Windows XP Version with Windows Vista Version with Windows 7
Internet Explorer IE 8.0 IE 9.0 IE 10.0
Firefox 15.0 20.0 20.0
Chrome (recommended) 24.0 and later 24.0 and later 24.0 and later
First Acess to the IFE Web Pages

The IFE name must be configured during the first access to the IFE web pages.
The procedure to access the IFE web pages for the first time depends on the operating system of the
computer:
z Windows Vista, Windows 7, or newer operating systems
z Windows XP or older operating systems
First Access Through PC with Windows 7 or Windows Vista
Step Action
1 Disconnect the PC from the local area network (LAN) and switch off Wi-Fi.
2 Connect an Ethernet cable from the computer to the IFE or to the Ethernet switch inside the panel.
3 Open Windows Explorer.
4 Click Network and the IFE-XXYYZZ appears in the list of devices.
NOTE: If the IFE-name is not displayed in the list of devices in Windows Explorer, check if the PC and the IFE are not connected
through the router.
5 Double-click the selected IFE-XXYYZZ, the login page automatically opens in the browser.
6 Type Administrator as the user name and Gateway as the password, the home page automatically opens in the browser.
NOTE: The user name and password are case sensitive.
7 To localize the IFE-XXYYZZ, select the Setup menu, go to Device Localization/Name submenu, click Device physical
localization, and click Blink ON. The ULP LED of the selected IFE-XXYYZZ blinks for 15 seconds (test mode).
8 To name the IFE-XXYYZZ, select the Setup menu, go to Device Name submenu, click Device Name. Click IFE-XXYYZZ to set
the IFE name.
9 Write the IFE name on a blank device name label and stick it on the existing one.
NOTE: XXYYZZ are the last 3 bytes of the MAC address in hexadecimal format.
First Access Through PC with Windows XP or Other Operating System
Step Action
1 Disconnect the computer from the local area network (LAN) and switch off Wi-Fi.
2 Connect an Ethernet cable from the computer to the IFE.
3 Start the web browser (see page 33).
NOTE: The computer automatically uses the default IP address 169.254.#.# (#=0–255) and the default subnet mask 255.255.0.0.
4 In the address text box, type 169.254.YY.ZZ, where YY and ZZ are the last 2 bytes of the IFE MAC address (to be found on
the IFE side label), then press Enter: the home page opens in the browser.
Example: For an IFE with MAC address 00-B0-D0-86-BB-F7 or 0-176-208-134-187-247 in decimal, type 169.254.187.247 in the
address text box.
5 Press Enter, the login page automatically opens in the browser.
6 Type Administrator as the user name and Gateway as the password. The homepage automatically opens in the browser.
NOTE: The user name and password are case-sensitive.
7 To localize the IFE-XXYYZZ, select the Setup menu, go to Device localization/Name submenu, click Device physical
localization, go to Device physical localization and click Blink ON. The ULP LED of the selected IFE-XXYYZZ blinks for
15 seconds.
8 To name the IFE-XXYYZZ, select the Setup menu, go to Device localization/Name submenu, click Device Name, go to Device
Name. Click IFE-XXYYZZ to set the IFE name.
9 Write the IFE-name on a blank device name label and stick it on the existing one.
DOCA0084EN 03/2014 33
IFE Web Server
NOTE: XXYYZZ are the last 3 bytes of the MAC address in hexadecimal format.
Access to Web Pages

Follow the Network Discovery, Name Browsing, and IP Address Browsing process to access the web
pages.
The web page access depends on the IT infrastructure.
Network Discovery
Follow the below procedure to access the IFE web pages once the IFE name has been configured.
Step Action
1 Connect the IFE or the Ethernet switch inside the panel to the local area network (LAN).
2 Connect the computer to the local area network (LAN).
3 Open Windows Explorer.
4 Click Network, the IFE-name is displayed in the list of devices.
NOTE: If the IFE-name is not displayed in the list of devices in Windows Explorer, check if the PC and the IFE are not connected
through the router.
5 Double-click the IFE-name which is written on the sticker located on the front face of the selected IFE, the login page automatically
opens in the browser.
Name Browsing
DNS server is mandatory.
Step Action
4 In the address text box, type the IFE-name which is written on the sticker located on the front face of the selected IFE.
NOTE: If the IFE does not appear in the list of devices in Windows Explorer, check if the PC and the IFE are not connected
through the router.
IP Address Browsing
IP static configuration has to be set.
Step Action
4 In the address text box, type IP address given by the IT administrator.
NOTE: If the login page in the web browser does not open or does not display correctly, check if Internet
Explorer\Tools\Compatibility View Settings\Display Intranet sites in Compatibility View in Internet Explorer is checked.
34 DOCA0084EN 03/2014
IFE Web Server
First Time Log In

The web browser is a tool for reading and writing data. You will be prompted to change your password the
first time you login, to prevent unauthorized access.
WARNING
UNAUTHORIZED DATA ACCESS
z Immedietly change the default password to a new and secure password.
z DO NOT distribute the password to unauthorized or otherwise unqualified personnel.
Failure to follow these instructions can result in death, serious injury, or equipment damage.
NOTE: A secure password should not be shared or distributed to unauthorized personnel. The password
should not contain any personel or obvious information.
DOCA0084EN 03/2014 35
IFE Web Server
IFE User Interface Layout
Overview
This graphic shows the IFE user interface layout.
A Banner
B Menu tabs
C Subtabs
D Action button
E Display zone
Banner
The banner displays the following information at the top of all the pages.
Generic Information Description

User name checked Name of the user who has logged in
Home A link to the home page
Documentation A link to the required documentation
Logout To log out the IFE session, click Logout or close your browser. It is recommended to log out from the IFE
when it is not in use.
Main Tabs
The main tabs are:
z Monitoring
z Control
z Diagnostics
z Maintenance
z Setup
Subtabs
The subtabs display the submenus under the selected main tab.
36 DOCA0084EN 03/2014
IFE Web Server
Action Buttons
The action buttons correspond to the selected tab and it varies.
The following table describes the interface buttons:
Button Action
Save changes Validates the modification.
Apply Applies the changes.
Cancel Cancels the modifications to return to the last saved settings.
Display Zone
The display zone shows the selected subtab in detail with all the related fields.
DOCA0084EN 03/2014 37
IFE Web Server
IFE Web Page Description
Monitoring Web Page
Monitoring Submenu Web Page Description

Real Time Data Single Device Pages The single device pages table view provides, basic readings of selected devices.
(see page 62)
Summary Device Pages The summary device pages table view provides, summaries of one or more
(see page 62) selected devices.
Trending The trending page view provides, real-time graphic and table trending of common
(see page 62) topics across multiple devices.
Device Logging Single Device Pages The single device pages provides, the graphic and table trending logs of user-
(see page 64) selectable quantities for selected devices.
Summary Device Pages The summary device pages provides, graphic trending logs of multiple devices with
(see page 66) a common topic.
Control Web Page
Control Submenu Web Page Description

Single Device Control Single Device Control Resets and controls the connected slave devices.
(see page 67)
Diagnostics Web Page
Diagnostics Submenu Web Page Description

General Statistics Displays diagnostic data used to troubleshoot the network-related problems.
(see page 70)
Product Information Device Information z Displays the IFE basic information to set the IFE device name and helps in the
(see page 72) device physical localization.
z Contains information about the product name, serial number, model number,
firmware version, unique identifier, IPv4 address, IPv6 link local address, IPv6
global address#1, and IPv6 global address#2.
IMU Information Displays the list of the IMU devices connected to the ULP port.
(see page 73)
Device Health Check Read Device Registers Displays register data connected locally to the IFE.
(see page 74)
Communication Check Verifies the communications health of all the slave devices connected to IFE.
(see page 75)
Maintenance Web Page
Maintenance Web Page Description

Submenu
General Maintenance Log Shows the date, time, and user who last performed maintenance on the equipment,
(see page 77) and provides entry detail on the maintenance performed.
Maintenance Counters Maintenance Counters Displays the maintenance counters of the connected devices.
(see page 78)
38 DOCA0084EN 03/2014
IFE Web Server
Setup Web Page
Setup Submenu Web Page Description

Device Physical Device physical localization z Localizes the device IFE-XXYYZZ
Localization/Name (see page 41) z Click Blink ON.
z The ULP LED of the selected device IFE-XXYYZZ blinks and is active for 15 s
(Test mode: 1 s ON, 1 s OFF).
Device Name Configures the IFE device name
(see page 42)
Network Configuration Ethernet Configuration (Dual Configures the Ethernet.
port)
(see page 43)
IP Configuration Configures the IP parameters.
(see page 44)
Modbus TCP/IP Filtering Configures the maximum number of Modbus TCP/IP server connections. Configures
(see page 46) the IP addresses that can access the IFE through Modbus TCP/IP.
Serial Port Configures serial communication parameters.
(see page 47)
Date/Time Date and Time Sets the date and time manually.
Configuration (see page 48)
E-mail Configuration E-mail Server Configuration Configures the alarms to be e-mailed.
(see page 49) Configures the SMTP parameter for mailing purpose.
Alarms To Be E-mailed Configures the alarms to be sent through e-mail.
(see page 50)
Device Configuration Device List Configures local serial devices on the Modbus serial daisy chain and IMU core
(see page 51) product connected to the ULP port.
Device Logging Configures device logging parameters.
(see page 53)
Device Log Export Configures device logging export options.
(see page 54)
Other Configuration SNMP Parameters Configures Simple Network Management Protocol (SNMP).
(see page 55)
Documentation Links Configures file and URL documentation links.
(see page 56)
Preferences Configures IFE preferences.
(see page 57)
Advanced Services Control Configures the advanced service control parameters.
(see page 58)
User Accounts Creates and edits groups and users. Configures e-mail accounts.
(see page 59)
Webpage Access Configures web page access rights for each user group.
(see page 60)
DOCA0084EN 03/2014 39
IFE Web Server
IFE Web Server - Setup Pages
Section 2.2
IFE Web Server - Setup Pages

Topic Page
Device Localization/Name 41
Device Name 42
Ethernet Configuration (Dual Port) 43
IP Configuration 44
Modbus TCP/IP Filtering 46
Serial Port 47
Date and Time 48
E-mail Server Configuration 49
Alarms to Be E-mailed 50
Device List 51
Device Logging 53
Device Log Export 54
SNMP Parameters 55
Documentation Links 56
Preferences 57
Advanced Services Control 58
User Accounts 59
Web Page Access 60
40 DOCA0084EN 03/2014
IFE Web Server
Device Localization/Name
Device Physical Localization
Step Action Result

1 From the IFE menu bar, click Setup. Opens the Setup menu.
2 From the Setup menu, in the Device Localization/Name submenu, click Opens the Device Physical Localization page.
Device Physical Localization.
3 In Device Physical Localization webpage, click Blink ON. Sets the IFE in nominal mode and the LED blinks in
ULP pattern.
NOTE: If the level value is changed, you are prompted to restart the device to take changes into account.
DOCA0084EN 03/2014 41
IFE Web Server
Device Name
Device Name Configuration
Step Action Result

2 From the Setup menu, in the Device Localization/Name submenu, click Opens the Device Name page.
Device Name.
3 In Device Name Configuration webpage, enter the device name and click Sets the IFE in test mode and the ULP LED blinks
Apply. accordingly.
42 DOCA0084EN 03/2014
IFE Web Server
Ethernet Configuration (Dual Port)
Ethernet
Parameter Description Settings

MAC address A unique media access control address of an IFE. The MAC -
address is written on the label which is placed on the side of
the IFE.
Frame Format Used to select the format for data sent over an Ethernet z Ethernet II
connection. z 802.3
z Auto (Factory setting)
Ethernet Port Control

Speed and mode for Port #1 Used to define the physical Ethernet connection speed and Auto-negotiation (Factory setting)
transmission mode for Ethernet port 1.
Speed and mode for Port #2 Used to define the physical Ethernet connection speed and Auto-negotiation (Factory setting)
transmission for Ethernet port 2.
Broadcast Storm Protection

Level Defines the storm protection level. The level value z 0 (Factory setting)
corresponds to a committed information rate (CIR) value, that z 1
is, the amount of traffic entering the switch port from which the z 2
storm protection drops entering the broadcast traffic. z 3
z 4
NOTE: If the level value is changed, you are prompted to
z 5
restart the device to implement changes.
z 6
Committed Information Rate Defines the read-only value of the storm protection level. -
DOCA0084EN 03/2014 43
IFE Web Server
IP Configuration
IPv4 Configuration

Obtain an IP address automatically using Used to select the mode for assigning the z DHCP (Factory setting)
IPv4 parameters set. Obtain IPv4 z BOOTP
parameters automatically using BOOTP or
DHCP.
NOTE: While using a DHCP server, the
device name must be limited to 16
characters.
Manual IP address Used to enter the static IP address of an 169.254.X.Y (Factory setting)
IFE.
NOTE: X and Y are the last 2 bytes of the IFE
MAC address (which is found on the IFE label).
Manual Subnet mask Used to enter the Ethernet IP subnet mask 255.255.0.0 (Factory setting)
address of your network.
Manual Default gateway Used to enter the gateway (router) IP 169.254.2.1 (Factory setting)
address used for wide area network (WAN) Factory setting of gateway is same as the default
communication. IP address of the IFE.
IPv6 Configuration

Enable IPv6 Defines the IPv6 configuration. z Enabled
z Disabled (Factory setting)
Link local address Used to open the IFE web page for future -
use.
NOTE: In the URL address box, use [ ]
brackets to enter the link local address.
DNS
Parameter Description Setting

Obtain DNS address automatically Defines the dynamic behavior of the DNS server Disabled when we select manual
address configuration. Used to obtain the IP address setting
from the DNS server automatically.
NOTE: Domain name system (DNS) is the naming
system for computers and devices connected to a loal
area network (LAN) or the Internet.
Manual Primary server address Defines the IPv4 address of the primary DNS server. -
Manual Secondary server address Defines the IPv4 address of the secondary DNS server. -
Used to perform a DNS resolution when the resolution
fails with the primary DNS server.
Duplicate IP Address Detection

While connected to your network, the IFE publishes its IP address. To avoid any duplicate IP address
conflicts, the IFE uses the address resolution protocol (ARP) to see if any other device on your network is
using the same IP address. The below table explains how the IFE handles a duplicate IP address when it
is detected.
44 DOCA0084EN 03/2014
IFE Web Server
Duplicate IP Address Scenario
Scenario Duplicate IP Detected Network Status LED

Ethernet link detected Reverts to the default IP address, subnet mask, and gateway Steady red
address. ARP requests are sent every 15 seconds until the IP
address is available. IFE uses the IP address when it is available,
Manual address change Reverts to the default IP address, subnet mask, and gateway Steady red
address. The ARP requests are sent every 15 seconds until the IP
address is available. The IFE uses the IP address when it is
available.
Receives an ARP request If more than one ARP is detected within 10 seconds, initiate the OFF
process to reacquire the IP.
DOCA0084EN 03/2014 45
IFE Web Server
Modbus TCP/IP Filtering
Description
This page allows the user to define the level of access for Modbus TCP/IP clients connected to IFE.
Block Connections
You can select the maximum number of IP connections allowed, 8 or 16.
NOTE: When the maximum number of IP connections is changed, a message pops-up on the screen Max
Connection is changed. Restart the Device to Take Effect and prompts the user to restart the device.
IP Filtering

Enable IP_Filtering Activates the IP address filtering. The list of IP z Enabled
addresses available in the table is granted access. z Disabled (No filtering)
Address Filters the required IP address entered by the user. 10 addresses (Maximum allowed IP addresses)
Accessibility Defines the access level for the corresponding IP z Read: The following Modbus TCP/IP function codes
address. are allowed:
z 1 (0x01)
z 2 (0x02)
z 3 (0x03)
z 4 (0x04)
z 7 (0x07)
z 8 (0x08)
z 11 (0x0B)
z 12 (0x0C)
z 17 (0x11)
z 20 (0x14)
z 24 (0x18)
z 43 (0x2B), with subfunction codes 14 (0x0E), 15
(0x0F), and 16 (0x10).
z 100 (0x64)
z none: The access to the IP address is blocked.

z read/write: Full access is provided.
Allow Anonymous IP Allows all Modbus TCP/IP clients to have the read- z Enabled
only access. z Disabled (Factory Setting)
46 DOCA0084EN 03/2014
IFE Web Server
Serial Port
Serial Port Settings
Parameter Settings
Baud rate z 9600 bps
z 19200 bps (Factory setting)
z 38400 bps
Parity z Even (1) (Factory setting)

z Odd (1)
z None (2)
Stop bits z Auto Stop bits (Factory setting)

z 1 bit
z 2 bits
Termination z Enabled
Response Timeout z 1 s (Factory setting)

z 0.1–0.5 s
z 1–10 s
NOTE: When Stop bits parameter is set to Auto, the actual value is based on the parity chosen.
DOCA0084EN 03/2014 47
IFE Web Server
Date and Time
Local Date and Time

Current Date Allows the user to set the present date manually. Date format: yyyy-mm-dd
NOTE: Date and Time Synchronization should be in manual mode.
Current Time Allows the user to set the present time manually. Time format: h: min: sec
NOTE: Date and Time Synchronization should be in manual mode.
48 DOCA0084EN 03/2014
IFE Web Server
E-mail Server Configuration
E-mail Server

SMTP Services: Enable/Disable Allows the user to enable or disable the e-mail service in IFE. z Enabled
E-mail (SMTP) server address Allows the user to enter an E-mail server address (SMTP -
server).
NOTE: Contact your network administrator to know the IP
address or the name of the simple mail transfer protocol
(SMTP) server.
Authentication enable If the SMTP server requires login information, enable the 0.0.0.0–255.255.255.255 or the
Authentication Enable check box. name of the SMTP server.
Example: smtp.server.com
From address In the From Address text box, type the e-mail address of the -
administrator who is administering the device.
DOCA0084EN 03/2014 49
IFE Web Server
Alarms to Be E-mailed
Description
This feature is supported for the device connected on the ULP port. Alarms to be e-mailed provides the list
of the alarms that can be selected for the notification through e-mail. The list of available alarms depends
on the devices connected to the ULP port.
NOTE: If an e-mail SMTP server is not located on the same Ethernet network segment as IFE, ensure that
the IFE default gateway is properly configured.
NOTE: This feature supports only the unencrypted email server (SMTP). For the encrypted email servers
we need to have a proxy server which accepts unencrypted connections, encrypts them, and forwards
them to normal SMTP server.
Parameter Description
Alarms List of alarms for configuration
Notification A check box to enable the notification.
To-Recipients Allows the user to choose from a list of E-mail recipients.
Custom-Text Allows the user to enter a custom text.
50 DOCA0084EN 03/2014
IFE Web Server
Device List
Description
The device list is used to discover the list of devices connected to the IFE ULP port and serial port.
NOTE: The web page are supported only for the devices added in the device list.
Device List Parameters
Parameters Description Settings

Number of Viewable Devices The maximum number of viewable devices displayed on the 1–13
web page.
Connection Selects the connection type. The 2 types of port are:
z ULP port
z Serial port (available for commercial
reference LV434011)
Device Type List of supported devices (see page 81) –
Device Name The list of supported devices by the IFE web page. –
z For ULP port: Click edit, and then click the Device
Name to edit the device name,
z For Serial port: Click Device Name to edit the device
name.
Local ID The local address of the device connected to the IFE. z For ULP port: 255 (Fixed)
z For serial port: 1–247
When you start the device, the IFE queries the ULP and serial port using a user-defined address range.
Modbus RTU protocol is used for discovery on the serial port. If the device replies to the query, the local
ID is set to the current discovery address, and the device is given a default device name. The IFE, then
tries to identify the device type. If the IFE recognizes the device type of the discovered device, the IFE sets
the recognized device type in the Device Type field. If the IFE does not recognize the Device Type of the
discovered device, the IFE sets to Modbus in the Device Type field.
The list of devices supported by the IFE is in Appendix (see page 81).
Device Discovery Procedure
Step Action Result

2 From the Setup menu, in the Device Configuration submenu, click Opens the Device List page.
Device List .
3 To discover locally connected devices, click Discover. Opens the Device Discovery page.
4 Enter Start Address and End Address. Enters the discovery address range.
5 Click Start Discover. (Click Stop Discover to stop the process). Begins to discover all connected devices.
NOTE: Discovery only finds local serial Modbus devices connected to
the IFE. The device on the ULP port is discovered automatically.
6 Enter a new device name in the Name text box. Renames the device.
7 Select the Save check box for the device to be saved in the device list. Selects or deselects a device entry to be saved or
removed.
8 Click Apply in the Device Discovery page. Displays the saved device list.
Adding a Device
In order to add a device, either choose the Device Discovery procedure or follow the below procedure to
add the device manually.
Step Action Result

1 Choose the supported device from the Device Type list. Selects the device type selected from the list.
2 Enter a new device name in the Name text box. Renames the device.
3 Enter the local address of the device. Displays the local address of the device.
4 Click Apply. Displays the new device added to the list.
DOCA0084EN 03/2014 51
IFE Web Server
Device Discovery Parameters
Parameters Description Setting

Start/End Address Defines the Modbus slave address range that is to be z Start address: 1–247 (Factory setting: 1)
used to discover devices on the IFE serial port. z End address: 1–247 (Factory setting: 10)
Save Allows you to save the selected device to the Device -

List.
Connection Displays the connection on which the device was z ULP port (Factory setting)
discovered or validated. z Serial port
Defined Lists the device type that was defined for this device. –
Assigned Allows you to assign the device type from the drop-down –
list.
Name Allows you to enter a custom name for the device. –
Local ID The slave address of the device connected to the IFE. -
Status Displays the discovery or validation status. z Attempting (trying to determine the device type that
matches in the device list.)
z Discovering (query attempt of device which is not in the
device list.)
z Found (device found but the device type does not
match what is defined in the device list.)
z Unknown (device found but the device type is
unknown.)
z Valid (device type identified and matches what is
defined in the device list.)
z Failed (failed to communicate with the device.)
52 DOCA0084EN 03/2014
IFE Web Server
Device Logging
Description
Logging is available for the devices which are in the device list. The IFE can log data received at predefined
intervals (5, 10, 15, 20, 30, and 60 minutes). Below is an explanation of how the IFE logs data and how to
set up logging for a device.
Logging Interval
Many devices in a power monitoring system do not have the ability to record data in non-volatile memory.
The IFE provides this data logging at predefined intervals for up to 13 devices.
The logging capacity is fixed in IFE, and it can be 12,960 entries per device. The logging capacity of each
data-log file can be calculated by dividing the maximum possible number of recorded intervals a data-log
file can contain (12960) by the multiplication (product) of the minutes per day and the logging interval.
Logging capacity = (12960/1440)*Logging interval
Where:
z 12960 - number of entries per device
z 1440 - minutes per day
z Logging interval in minutes
Logging Interval (Minutes) Logging Capacity (Days)

5 45
10 90
15 135
20 180
30 270
60 540
Interval Logging Setting Procedure

Each device in the device list may be independently enabled for logging. Topics to log are unique to each
device. To view interval data logs, refer to Device Logging (see page 64) in Monitoring menu.
NOTE: To enable the Device Logging feature, there must be a time value selected from the Logging
Interval drop-down list. It is recommended to disable the logging feature for the specific device being
configured. To do this, clear the logging check box for the device being selected.
Logging
To disable logging, select a logging interval of zero, ensure that the logging selections are cleared, then
click Apply.
Purge Data
To delete a data log, check Purge Data for the topics to be deleted.
Customize
To customize logging content, enable device logging. Click Topics under Customize for the device to be
configured.
DOCA0084EN 03/2014 53
IFE Web Server
Device Log Export
Description
Device Log Export is used to export the device logs automatically by IFE. The device log export allows the
user to configure IFE to export device logs periodically. User can choose to export the device log files
through e-mail or FTP.
NOTE: If the e-mail and the FTP servers are not located on the same Ethernet network segment as the
IFE, ensure that the IFE default gateway is properly configured.
Transport

Disabled When Disabled is selected, either e-mail or FTP is enabled. -
E-mail Allows the user to choose the way of exporting the log files through e-mail. -
NOTE: When E-mail is selected, Test E-mail is enabled.
Test E-mail Sends an e-mail to the mail configured in the e-mail server configuration. The e-mail message -
contains the device information, and the device name with the date and time.
FTP Allows the user to choose the way of exporting the log files through FTP. -
NOTE: When FTP is selected, Test FTP is enabled.
Test FTP Sends the text file to the FTP server configured in the FTP parameters. The text file contains -
the device information, and the device name with the date and time.
Incremental Selects only the new interval data logged since the last successful data export. -
NOTE:
z If the transport is scheduled for Hourly or Logging Interval, the incremental check box is
selected automatically.
z If the Incremental check box is not selected, the complete log file is sent through an e-mail
as an attachment on each scheduled interval.
Schedule

Logging Interval Selects how often the data logs are sent. z Hourly
z Daily
z Weekly
z Monthly
z Logging Interval
To Addresses

To Addresses Lists the e-mail recipients configured in the IFE user accounts. -
54 DOCA0084EN 03/2014
IFE Web Server
SNMP Parameters
Manage IP Parameters
The IFE supports SNMP, allowing a network administrator to access remotely an IFE with an SNMP
manager and to view the networking status and diagnostics of the IFE in the MIB-II format.

Manager One Allows the user to configure the IP address of SNMP manager one. -
Manager Two Allows the user to configure the IP address of SNMP Manager Two. -
System Contact Allows the user to configure the SNMP system contact name. -
System Location Allows the user to configure the SNMP system location. -
Read-only Community Name Allows the user to configure the SNMP Read-only community name. Public (Factory setting)
Read-write Community Name Allows the user to configure the SNMP Read-write community name. Private (Factory setting)
Trap Allows the user to trap the community name. Public (Factory setting)
Enabled Traps

Cold Start Trap Generates a trap when the IFE is powered ON. -
Warm Start Trap Not supported -
Link Down Trap Generates a trap when an Ethernet port communication link is -
disconnected.
Link Up Trap Generates a trap when an Ethernet port communication link is -
reconnected.
Authentication Failure Trap Generates a trap when an SNMP manager is accessing the IFE with -
incorrect authentication.
DOCA0084EN 03/2014 55
IFE Web Server
Documentation Links
Description
The IFE supports two types of documentation links:
z Local file access (documentation stored onboard the IFE)
z URL access
Local File Access

To access the files, select Enabled for the file name link to be enabled. The local file documents to be
appeared on the documentation web page must be placed in the IFE wwwroot/documentation folder using
FTP.
URL Access

Enabled Always selected to enable the URL link access. -
New Window Always selected if the selected files and URLs to be opened in a new window -
when clicked.
Link Text Sets the documentation link that appears on the documentation page. 127 characters
File Name Displays the file name which is available in the IFE documentation link. -
URL Displays the link to the external web page to be accessed. -
56 DOCA0084EN 03/2014
IFE Web Server
Preferences
General Settings

Equipment name Displays the equipment name. This name is used in the web -
interface banner.
NOTE: The device name can be updated in the Device Name of
the Device Localization/Name in the Setup menu.
Default Home Page Allows selecting of the default home page. z Home (Factory setting)
z Circuit summary
z Load current summary
z Demand current summary
z Power summary
z Energy summary
Real Time Sample Rate Controls how often data is read from the device(s) in the 5–60 seconds
standard monitoring table views. Factory setting: 5 seconds
Communication Check Rate Controls how often a communications check is performed while Disabled or 5–30 minutes
the browser is displaying real time readings in the standard Factory setting: 15 minutes
monitoring table views. This function attempts to bring any out-
of-service devices back into service automatically.
DOCA0084EN 03/2014 57
IFE Web Server
Advanced Services Control
Industrial Protocol

Enable Modbus/TCP Allows the user to enable/disable the Modbus/TCP service. z Enabled (Factory Setting)
z Disabled
Services Configuration

Enable FTP server Allows the user to enable/disable the FTP service. z Enabled (Factory Setting)
z Disabled
Enable device announcement Allows the user to enable/disable the DPWS service. z Enabled (Factory Setting)
z Disabled
Enable SNMP Allows the user to enable/disable the SNMP service. z Enabled (Factory Setting)
z Disabled
58 DOCA0084EN 03/2014
IFE Web Server
User Accounts
Description
The IFE users are assigned with user names and passwords. Each user belongs to a group, and each
group has access rights to the IFE web pages assigned by the IFE administrator.
NOTE: There are two pre-defined user accounts:
z Administrator (the pre-defined password is Gateway)
z Guest (the pre-defined password is Guest)
Groups
To change the group name, type a new name in one of the groups text boxes.
NOTE: The Administrator group name cannot be changed.
Users
Name Enter a name (1 to 15 characters) for a new user.
NOTE: User names are case-sensitive and can contain only alphanumeric characters.
Password Enter a password (0 to 11 characters) for a new user.
E-mail Id Enter a valid e-mail address for the selected name.
Group Select a group for the new user.
Default Language Select the default language for the new user.
NOTE: The maximum number of user-defined accounts are 11.
IFE Accounts and Passwords
Accounts Password
Administrator Gateway
Guest Guest
User-defined accounts (11 accounts possible) User-defined passwords
NOTE: The passwords can be reset by the user.
DOCA0084EN 03/2014 59
IFE Web Server
Web Page Access
Group Access
Group Access
Administrator Full access to all web pages.
NOTE: It is recommended to change the default administrator password for system security the first time you
log in.
Guest Read-only access to selected web pages.
User-defined groups Choosing from the following options, the administrator assigns web page access for each group. The access
levels are as follows:
z None: A group has no access to selected web page
z Read-Only: The password grants a group read-only access to the selected web page
z Full: A group has the same access as the administrator group to the selected web page
NOTE:
z The Webpage Access is available for the Administrator only.
z The Administrator has full access to all the web pages.
60 DOCA0084EN 03/2014
IFE Web Server
IFE Web Server - Monitoring Pages
Section 2.3
IFE Web Server - Monitoring Pages

Topic Page
Real Time Data 62
Device Logging 64
DOCA0084EN 03/2014 61
IFE Web Server
Real Time Data
Description
The real time data page provides:
z the basic readings of the selected devices in real time on Single Device Pages.
z the device summaries on Summary Device Pages.
z the real time trending for the selected device for the selected topics on Trending.
NOTE: Refresh the web page by action on the function key F5 when Out of service is displayed.
Single Device Pages
Step Action Result

1 From the IFE menu bar, click Monitoring. Opens the Monitoring menu.
2 From the Monitoring menu, in the Real Time Data Displays the real time data of the selected device.
submenu, select a device from Single Device Pages.
3 At the top of the display, select either Load Current, Selects the quantities to be displayed on the Analog Gauge graphic
Power, Voltage LL, or Voltage LN to be displayed on the display.
Analog Gauge graphic display. NOTE: Analog gauges are not available for all device types.
4 The gauges automatically adjust their display range. Controls the display range of the Analog Gauges.
5 Click Apply. Updates the gauge selection for the device page.
Summary Device Pages

The summary device table views provide summary of one or more selected devices.
Step Action Result

1 From the Monitoring menu, in the Real Time Data Expands tree for summary page selection choices.
submenu, click Summary Device Pages.
2 Select the Summary Page to be viewed. Opens the device selection list.
3 Select a device(s) from the Available Devices, then click Selects a device(s) for the summary options.
Next.
NOTE: Click >> to select all the available devices.
Trending
Step Action Result

2 From the Monitoring menu, in the Real Time Data Expands the data tree for real time data option selection and the time
submenu, select Trending. trending option selection.
3 Select Real Time Trending. Opens the Real Time Trending setup page.
4 Select up to 4 devices from the Available Devices list. Selects devices for trending.
5 Select a topic(s) from the Available Topics list. Selects topics for trending.
NOTE: Only topics common to all selected devices are
available for trending. The maximum number of topics to
trend is dependent on the number of devices selected.The
multiplication (product) of the selected devices and the
selected topics must be 8 or less.
6 Click Next to open the Real Time Trending display page. Opens the Real Time Trending display page.
7 Set the trending parameters. Allows trending parameters to be set.
62 DOCA0084EN 03/2014
IFE Web Server
Trending Parameters
Step Action Result

1 Select Absolute or Relative trending. Selects graph mode.
NOTE: Absolute redraws the graph’s x-axis after each
sample, filling it with all the data collected since the start of
the trend. The Relative updates the graph with the latest
data after each sample while the x-axis stays constant to
show the overall trend time selected.
2 Choose a trend time from 1 to 15 minutes. This is the Selects the amount of time of the trend.
duration of the trend.
NOTE: Data samples are taken as fast as possible but may
take longer depending on the communications load on the
Modbus-SL port.
3 Select Start Sampling to start the trending of the selected Starts trending.
device topics.
NOTE: Trending may be stopped before reaching the trend
time by clicking Stop Sampling. If, after stopping the
sampling, Start Sampling is pressed, a new trend is
started.
4 Press Data Points to view a log of all the sampled topics Displays a log of all topic values sampled during the trend.
recorded during the trend time.
5 Press New Topics to reselect the devices and topics to Navigates back to the Real Time Trending setup page.
trend.
DOCA0084EN 03/2014 63
IFE Web Server
Device Logging
Introduction
Device logging page provides the graphic and table representations of the selected device log data. For
more details on configuring device logging, refer to Device Logging (see page 53).
Single Device Pages
Step Action Result

2 From the Monitoring menu, click Device Logging. Expands tree to show available device logging choices.
3 From the Device Logging, click Single Device Pages. Expands tree to show available devices that have logged data available
for viewing.
4 Select a device from the Device List. Displays the device log for the selected device.
5 To view a data range, select a period range from the Plots the selected period range.
period range drop-down list:
z Last Full Day
z Last Full Week
z Last Full Month
z All
6 Hold the left mouse button and drag a selection box Zooms in on the selected graph area.
around a graph area to zoom in on it.
7 To return to the original full view, type Z on your The view zooms out.
keyboard, or double-click the graph.
8 Click Data Points to view the selected interval data log Opens the selected Interval Data Log table.
table.
9 To view different topics, click New Topic(s). Enable the Enables the display of the selected topic(s).
check box(es) of the topic(s) to be displayed, and click
Apply.
The data logged from each device is displayed in a web page in a time-trend chart format. The time-trend
chart is preconfigured to display data from the Last Full Day, Last Full Week, Last Full Month, or All.
Energy parameters are logged as accumulating values but are displayed as incremental values on an
interval basis. All other parameters are logged and displayed as the actual value recorded.
Retrieving a Data Log

Interval data logs can be retrieved using the methods given in the following table:
Retrieval Method File Format Retrieved

IFE FTP server Comma-separated variable (CSV)
Export to an external FTP server CSV
Data point button HTML
Microsoft Web Query CSV
E-mail CSV
To view the list of all the available log files, follow steps 2 to 4 in the section Getting an Interval Data Log
using FTP (see page 65). Files are in the format: Device Name.csv where the device name is the name
given to the slave device. For example, a device named Building 1 Utility Entrance will be Building 1 Utility
Entrance.csv.
When the log files are exported, the date and time are appended to the file name in the following format:
_YYYYMMDDHHMMSS. For example, Building 1 Utility Entrance_20100218115216.csv. This indicates
that the file was exported on 2010 February 18 at 11:52:16 AM.
64 DOCA0084EN 03/2014
IFE Web Server
Log Format
Data is logged in the CSV file with the following format:
Row Data in CSV Format Description

1 IFE Name,IFE SN, IFE Address, Device Name, Device Local This row contains the column headings for the information in
ID, Device Type Name, Logging Interval. row 2.
2 IFE 555, 23227,157.198.184.116, Building1 Utility Entrance, 3, This row contains the information about the IFE and the logged
CM4000,15 device.
3 This row is blank. -
4 ,,,Topic ID 1,Topic ID 2,Topic ID 3 This row contains the column headings for the topic IDs in row
5. A topic ID is a numerical reference to the quantity being
logged. Topic IDs are used to identify the quantity, regardless
of the device or language. The first three commas are used for
layout purposes in a spreadsheet application.
5 ,,,1617,1621,1625 This row contains the topic IDs of the values logged.
6 This row is blank. –
7 Error, UTC offset (Minutes), Local Time Stamp, Apparent This row contains the column headings for the data logged in
Energy (kVAh), Real Energy (kWh), Reactive Energy (kVARh) rows 8 and higher.
8 and higher These rows contain the logged data.
0,-300,2008-10-09 14:15:00,1400738.219,1201962.707,647069.906,15
0,-300,2008-10-09 14:20:00,1400758.260,1201980.725,647078.602,15
0,-300,2008-10-09 14:25:00,1400778.198,1201998.661,647087.233,15
If a spreadsheet application is used to view the CSV file, data should look similar to the Interval Data log
opened in a spreadsheet application.
Error Codes for Data Logs

The below error codes may be seen when troubleshooting data logs:
Error Code Definition Result

19 Communication error occurred (for example: CRC, protocol, Logging is left enabled unless the last interval was missed.
or exception).
25 Timeout occurred when a request was sent without receiving Logging is left enabled unless the last interval was missed.
a corresponding response within the allowed time.
38 Invalid data. -
100 Interval time expired before data could be recorded. Missed interval.
Contact technical support if you need assistance in resolving these or other error conditions.
Retrieving Data Log Using IFE FTP Server

You can use IFE FTP server to retrieve a data log file by connecting to the IFE via FTP and transferring
the .csv file, as shown in the steps below.
NOTE: If you want the IFE to send the data log file via FTP automatically, the device log export must be
configured for FTP.
Step Action Result

1 Create a folder on your computer, such as C\:file_logs. Creates a folder to store the IFE data log.
2 Launch Windows explorer, type ftp:// and the IP address of Opens the Log On As dialog box.
the IFE in the address text box (for example,
ftp://169.254.0.10), press Enter.
3 Type the user name as Administrator and password as Opens an FTP session with the IFE and displays the files stored
Gateway in the text boxes, click Log On. in the IFE.
4 Navigate to the directory/logging/data on the IFE. Opens the data logging directory on the IFE.
5 Copy the log file and paste it into the folder created in step 1. Copies the data log to the folder.
DOCA0084EN 03/2014 65
IFE Web Server
Retrieving Data Log Using the Data Points Button
Step Action Result

1 From the Device Logging web page, click Data Points. Opens a new window displaying the logged data.
2 Press CTRL+A, then press CTRL+C. Selects all of the data and copies the data to the clipboard.
3 Open Excel, then press CTRL+V. Pastes the data into an Excel spreadsheet.
Retrieving an Interval Data Log Using the Microsoft Web Query Feature
Step Action Result

1 Launch your web browser. Opens the web browser.
2 Verify that the log file is available by typing the IFE IP address Opens the data log page.
followed by /stream/devlog_data.html=x (where “x” is the device local
ID).
3 Launch Microsoft Excel. Opens the New Web Query dialog box.
z For Excel 2003: On the Data menu, go to Import External Data
and select New Web Query.
z For Excel 2007: On the Data menu, go to From Web and enter
the URL in the Address bar, and then click Import.
4 In the New Web Query dialog box, type the address of the log Opens the data log file.
entered in step 2, then click Go.
5 Click the outer-most arrow to select all of the data and click Import. Selects the data, then opens the Import Data dialog box.
6 Click OK. Imports the data.
NOTE: If you want to display the latest data each time you open the spreadsheet, click Properties on the
Import Data dialog and select Refresh data on file open.
Retrieving Data Log Using E-mail

The IFE must be configured to deliver data logs to an e-mail address. For more information, refer to E-mail
Export (see page 54).
Summary Device Pages

The Summary Device view provides the summary of one or more selected devices.
Step Action Result

1 From the Monitoring menu, click Device Logging. Expands the tree for device logging choices.
2 Under Device Logging, click Summary Device Pages. –
3 Under Summary Device Pages, click Single Topic for Multiple Opens the setup page for the Multiple devices, and Single
Devices. Topic page for Multiple Devices.
4 Select a device from the Available Devices list. Selects the devices for the summary options.
NOTE: A maximum of 4 devices may be selected.
5 Select a topic from the Available Topics list. Selects the topic to display for each selected device.
NOTE: Only topics that are common between the selected devices
are available.
6 Select Next. Displays the Single Topic for Multiple Devices page.
7 Hold the left mouse button and drag a selection box around a graph Zooms in on the selected graph area.
area to zoom in on it.
8 To return to the original full view, type Z on the keyboard, or double- The view zooms out.
click the graph.
The topic logged from the selected devices is displayed in a web page in a time-trend chart format. The
time-trend chart is preconfigured to display data from the Last Full Day, Last Full Week, Last Full Month,
or Last 6 Weeks.
Energy parameters are displayed as incremental values on an interval basis. All other parameters are
logged and displayed as the actual value recorded.
66 DOCA0084EN 03/2014
IFE Web Server
IFE Web Server - Control Page
Section 2.4
IFE Web Server - Control Page
Single Device Control
Reset Commands
The IFE Control page allows the user to execute one or more reset commands per device type.
From the Control menu, in the Single Device Control submenu, on the device list, select the device and
click Resets. Select an Operation in the Resets list to reset.
This feature is always enabled.
Application Control
The IFE Control page allows the user to control the following applications remotely:
z Breaker application
z IO application
By default, this feature is disabled in IFE.
Enable Application Control in IFE

Follow the below procedure to enable the Application Control feature in IFE.
NOTE: The application control feature is enabled only when the user is logged in as an Administrator.
Step Action Result

1 Press the test button on the front face of the IFE for 10 to Initiates the application control feature.
15 seconds.
2 After 15 seconds, IFE initiates the application control The application control feature window is available continuously for
feature. 5 minutes. The module status LED starts blinking continuously for
5 minutes (1 s ON, 1 s OFF) once the test button is released.
3 Access the IFE web page and login as an administrator. The administrator login to the IFE web page.
4 From the Setup menu, click Webpage Access. The Administrator reads the disclaimer and chooses either the
option I Understand the risks/Apply or Continue to disable.
The application control feature disclaimer is:
By accepting this disclaimer, you are directed to web page access
which enables you to control several applications remotely. It is
highly recommended that the Administrator modify the default
Administrator password. By using, you are agreeing to indemnify
and hold harmless Schneider Electric for and from any and all
claims , losses, demands, lawsuits and damages that are a result of
direct or indirect use of this application control feature by reason of
any act or emission which the user commits.
The disclaimer page is available in the language selected by the
administrator.
5 Select I Understand the risks/Apply. The application control feature is now enabled for the administrator.
The breaker application and IO application are enabled in the web
page access for providing access to the other user groups.
6 Select Continue to disable. The application control feature is disabled. The breaker application
and IO application are disabled in the web page access.
DOCA0084EN 03/2014 67
IFE Web Server
Breaker Application
From the Control web page, in the Breaker Application, the authorized group can perform the following
operations:
Control Status Operation Availability

Breaker Open/Close/Trippe Compact NSX Open/Close/Reset BSCM
d/NA
Masterpact NT/NW, Compact NS BCM ULP
Open/Close
NOTE: Pop-up message confirms the command is successfully sent. It does not confirm wether the
complete operation is successful.
IO Application
From the Control web page, in the IO Application, the authorized group can perform the following
operations:
Control Status Operation Availability

Reset input counters - I1 I2 I3 I4 I5 I6 IO 1
#I1 #I2 #I3 #I4 #I5 #I6 IO 2
Reset output counters - O1, O2, O3 IO 1
#O1 #O2 #O3 IO 2
Light control ON or OFF ON / OFF IO 1
Load control ON or OFF ON / OFF IO 1
User-defined output control ON or OFF ON / OFF IO 1 or IO 2
NOTE:
z The IO application control is possible only when the IO module is connected to a circuit breaker.
z The light and the load control are available when the application rotary switch of IO 1 is in position 4.
z The user-defined output control is available only when the user-defined output has been assigned with
customer engineering tool.
z If the input is assigned as a pulse counter, the operation is P1, P2, P3, P4, P5, and P6 for IO 1. For IO 2,
the pulse counter operation is #P1, #P2, #P3, #P4, #P5, and #P6.
68 DOCA0084EN 03/2014
IFE Web Server
IFE Web Server - Diagnostics Pages
Section 2.5
IFE Web Server - Diagnostics Pages

Topic Page
Statistics 70
Device Information 72
IMU Information 73
Read Device Registers 74
Communication Check 75
DOCA0084EN 03/2014 69
IFE Web Server
Statistics
Description
This page shows the readings accumulated since the IFE was last activated. If the power to the IFE is
terminated or the device is reset due to a configuration change or other event, all cumulative values are
reset to 0.
Reset Procedure
Step Action Result

1 From the IFE menu bar, click Diagnostics. Opens the Diagnostics menu.
2 From the Diagnostics menu, in the General submenu, click Statistics. Opens the Statistics page.
3 View the data. See the statistics for each group.
4 Click Reset. Resets the IFE cumulative diagnostic data to 0.
Interpreting Ethernet Statistics
Global Statistic Description

Received Frames Number of frames received
Transmitted Frames Number of frames transmitted
Reset Counters Resets the transmitted and received frames
Statistic Per Port Description

Link Speed Operational speed (10 Mbps or 100 Mbit/s)
Duplex mode Current mode of operation (full duplex or half duplex)
Interpreting Modbus TCP/IP Statistics
Statistic Description
Port status Status of the connected Ethernet port
Opened TCP connections Number of active connections
Received messages Number of messages received
Transmitted messages Number of messages transmitted
Reset counters Resets the received and transmitted messages
Interpreting System Statistics
CPU Status of the CPU:
z Nominal
z Degraded
z Out of service
Boot Memory Healthiness of the boot memory

EEPROM Healthiness of EEPROM
File System Healthiness of the file system
Ethernet PHY 1 Healthiness of PHY1 hardware
Ethernet PHY 2 Healthiness of PHY 2 hardware
DDR Healthiness of the execution memory
70 DOCA0084EN 03/2014
IFE Web Server
Interpreting Date and Time Statistics
Date Current date
Time Current time
Uptime Run time during the system power-up
Interpreting Modbus Serial Statistics
Transmitted Message A counter that increments each time a frame is sent.
Received Message A counter that increments each time a frame is received.
Error Message An error marked from the slave or the response timeout.
Interpreting ULP Statistics
Frames Transmitted Number of CAN frames transmitted successfully
Frame Received Number of CAN frames received successfully
Max Transmit Error Maximum number of CAN transmitted errors (TEC)
Max Receive Error Maximum number of CAN received errors (REC)
Bus off CAN Bus off count
Max Bus off Maximum number of Bus off counts
Interpreting File System Statistics
Total Size Total amount of the IFE disk size in kilobytes
Used Size Total amount of used disk size on the IFE disk in kilobytes
Free Size Total amount of unused disk space on the IFE disk in kilobytes
Bad Size Amount of corrupted disk space on the IFE disk in kilobytes
Interpreting TCP Port Connections Statistics
Statistics Description
Remote IP Remote IP address
Remote Port Remote port number
Transmitted messages Number of messages transmitted
Received messages Number of messages received
Sent Errors Number of error messages sent
Reset Counters Resets the transmitted and received messages
DOCA0084EN 03/2014 71
IFE Web Server
Device Information
Device Name Configuration Procedure
Step Action Result

1 From the IFE menu bar, click Diagnostics. Opens the Diagnostics page.
2 From the Diagnostics menu, in the Product Information submenu, click Device Opens the Device Information page.
Information.
List of Parameters in Device Information
Device name Device name which is updated in the device name field
Product name Name of the product
Serial number Device serial number
Model number Device model number
Firmware version Current firmware version
Unique Identifier Combination of MAC address and the time
MAC address Unique MAC address
IPv4 address Addressing scheme to specify the source and destination addresses
IPv6 link local address Address used to communicate on the local network
72 DOCA0084EN 03/2014
IFE Web Server
IMU Information
Description
This page gives the information about the devices which are connected to the IFE in ULP port. The devices
connected are:
z Breaker Communication Module
z Breaker Communication Module for ULP system
z Micrologic Trip Unit
z Breaker Status and Communication Module
z FDM121 display for LV circuit breaker
z IO 1
z IO 2
z Maintenance module
DOCA0084EN 03/2014 73
IFE Web Server
Read Device Registers
Description
Read device registers allows the IFE to read Modbus registers from the selected device.
Read Procedure
Step Action Result

2 From the Diagnostics menu, in the Device Health Check Opens the Read Device Registers page.
submenu, click Read Device Registers.
3 From the Device Name, select the device. Selects the device from the drop-down list.
4 Enter Local (or choose from the defined device list), Starting Enters the registers to read from the specified device.
Register, and the Number of Registers to read.
5 Select Data type. Selects the appropriate data type.
6 To change how Modbus data is displayed in the Value column, Selects how the data values are displayed.
select Decimal, Hexadecimal, Binary, or ASCII.
7 Click Read. Reads the device registered according to the selected
configuration.
IFE Read Device Register Parameters

Device Name Selects a device to read from the list of previously added devices. A -
device not defined in the device list can be read by entering its Local
ID number.
Local ID The address (Local ID) of the device that is to be read. 1
Starting Register Register number in decimal. 0–65535
Factory setting: 1000
Number of Registers The number of registers to read. 1–125
Factory setting: 10
Register column Lists the register numbers in decimal. -
Value column Lists the data stored for a register. Values retrieved depend on the -
device connected to the IFE. Refer to the documentation for the
connected device for more information about stored register values.
Data type Lists the data types available for the device. z Holding Registers (Factory setting)
z Input Registers
z Input Coils
z Output Coils
Decimal, Hexadecimal, Select an option to specify how the Value column data is displayed. Decimal (Factory setting)
Binary, or ASCII options
74 DOCA0084EN 03/2014
IFE Web Server
Communication Check
Automated Communication Check

While browsing the Real Time Data views, the IFE has an automated communication check that runs every
15 minutes by default. To change the timing, refer to Preferences (see page 57). This check verifies the
communication health of all the devices configured on the IFE, and attempts to re-establish the
communication to any device marked out of service within the current browser session.
Manual Communication Check

In certain cases, the user may not want to wait for the automated communications check interval and need
to force the check to run manually.
Step Action Result

2 From the Diagnostics menu, in the Device Health Opens the Communications Check page.
Check submenu, click Communication Check.
3 Click Check Device Status. Runs a communications check.
The communicating device displays:
z Passed in the Comms column.
z In Service in the Status column.
A device that is not communicating display:

z Failed in the Comms column.
z Out of Service in the Status column if it has failed multiple times.
DOCA0084EN 03/2014 75
IFE Web Server
IFE Web Server - Maintenance Pages
Section 2.6
IFE Web Server - Maintenance Pages

Topic Page
Maintenance Log 77
Maintenance Counters 78
76 DOCA0084EN 03/2014
IFE Web Server
Maintenance Log
Description
The maintenance log provides a way to document maintenance performed on the IFE, the connected
equipment, or the system of which, the IFE is a part. Each entry is recorded with the date and time the entry
was made, and the name of the user who made it.
Maintenance Log Setting Procedure
Step Action Result

1 From the IFE menu bar, click Maintenance. Opens the Maintenance menu.
2 From the Maintenance menu, in the General submenu, click Open the Maintenance Log page.
Maintenance Log.
3 To add a new log entry, click Add Log Entry. Enter the Opens the Add Log Entry page and allows the user to enter
maintenance text details in Entry Detail text box and click Apply. the maintenance details.
4 Select the check box next to the entry to be deleted. Click Delete Deletes the selected entry.
Entries.
5 Click Delete Log to delete all the entries in the log. Clears the maintenance log.
DOCA0084EN 03/2014 77
IFE Web Server
Maintenance Counters
Description
This page provides the maintenance counter information for the selected device. The page displays the
information about the circuit breaker operation counters, contact wear counters, and the cradle counters.
Viewing Maintenance Counters
Step Action Result

1 From the IFE menu, click Maintenance. Opens the Maintenance page.
2 From the Maintenance menu, click Maintenance Opens the Maintenance Counters page.
Counters.
3 Select the device from the device list. Displays the information about the circuit breaker operation counters,
NOTE: This feature is available for circuit breakers contact wear counters, and the cradle counters.
only.
78 DOCA0084EN 03/2014
DOCA0084EN 03/2014
Appendices
DOCA0084EN 03/2014 79
80 DOCA0084EN 03/2014
Appendix A - List of IFE Supported Devices
DOCA0084EN 03/2014
Appendix A
List of IFE Supported Device Types
Description
The table below gives the list of devices that can be connected as Modbus slaves on an IFM stacked to
the IFE gateway. This list of supported devices was accurate at the time this document was published.
Check www.schneider-electric.com for updates.
Device Group Device

Masterpact NT/NW, Compact NS, and PowerPact P- Micrologic A
and R-frame circuit breakers with Micrologic trip units
Micrologic E
Micrologic P
Micrologic H
Compact NSX and PowerPact H-, J-, and L-frame circuit Compact NSX-A
breakers with Micrologic trip units Compact NSX-E
PowerPact - A
PowerPact - E
Insulation Monitoring Devices Vigilohm IM20
Vigilohm IM20-H
Motor Management TeSys T
Power Factor Controller Varlogic
Power Meters PM9c
PM800
PM800 A-S1/A-S2
PM1200
PM3250
PM5000
Others Acti9 Multicontrol
iEM3250
iEM3255
DOCA0084EN 03/2014 81

IFE Maksimalafbryder Ethernet Gateway

Uploaded by

Copyright:

Available Formats

IFE Maksimalafbryder Ethernet Gateway

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

IFE Maksimalafbryder Ethernet Gateway

Uploaded by

Copyright:

Available Formats

IFE Ethernet Interface for LV Circuit Breakers

IFE Ethernet Interface for LV

Title of Documentation Reference Number

What Is in This Chapter?

Intelligent Modular Unit

A FDM121 display for LV circuit breaker

Product Description Part Number

A Ethernet 1 and Ethernet 2 communication port

24 Vdc Power Supply

Ethernet Communication LEDs

LED Indication Status Description

Module Status LED

LED Indication Status Description

Network Status LED

LED Indication Status Description

Modbus Serial Line Traffic LED

Time Range Function

ULP LED Mode Action

Conflict Remove extra ULP module

Degraded Replace ULP module at the

Non-critical firmware Upgrade firmware at the next

Critical firmware discrepancy Upgrade firmware

Critical hardware discrepancy Replace ULP module

Stop Replace ULP module

Power OFF Check power supply

Customer Engineering Tool

z Masterpact RSU software to configure the Masterpact pre-defined alarm.

Electrical Asset Manager

Compact NSX RSU Software

z display the Micrologic tripping curves.

Masterpact RSU Software

z display the Micrologic tripping curves.

IFE Schematics With Masterpact NT/NW and Compact NS Circuit Breakers

Connection of the IFE to a Fixed Manually-Operated Compact NS Circuit Breaker

A IFE Ethernet interface for LV circuit breaker

A IFE Ethernet interface for LV circuit breaker

A IFE Ethernet interface for LV circuit breaker

A IFE Ethernet interface for LV circuit breaker

IFE Schematics With Compact NSX Circuit Breakers

Connection of the IFE to the Micrologic Trip Unit

A IFE Ethernet interface for LV circuit breaker

Connection of the IFE to the BSCM

A IFE Ethernet interface for LV circuit breaker

A IFE Ethernet interface for LV circuit breaker

A IFE Ethernet interface for LV circuit breaker

Certification cULus, CE, and FCC marking

Connections Screw type terminal blocks

24 Vdc Power Supply Characteristics

IFE Firmware Update

The firmware on the IFE can be updated using:

Executable Binary Component Firmware Version

Step Action Result

Getting the Web Page and the Device Supporting Files

Step Action Result

Step Action Result

Protecting the Environment

IFE Web Server

What Is in This Chapter?

IFE Ethernet Interface for LV Circuit Breaker