Insulator Selection

Document No._Rev.
Restricted
Insulators Selection Methodology

Primary Engineering
Export Control Classification:

ECCN: N AL: N
These items are controlled by the U.S. Government (when labeled with “ECCN” unequal “N”) and authorized for export only to the country of
ultimate destination for use by the ultimate consignee or end-user(s) herein identified. They may not be resold, transferred, or otherwise
disposed of, to any other country or to any person other than the authorized ultimate consignee or end-user(s), either in their original form or
after being incorporated into other items, without first obtaining approval from the U.S. Government or as otherwise authorized by U.S. law
and regulations. Items labeled with "AL” unequal "N” are subject to European / national export authorization. Items without label / with label
"AL:N" / "ECCN:N" or label”AL:9X9999” / “ECCN:9X9999” may require authorization from responsible authorities depending on the final
end-use, or the destination.
Restricted © Siemens Energy, 2023

Transmittal, reproduction, dissemination and/or editing of this document as well as utilization of its contents and communication thereof to R
others without express authorization are prohibited. Offenders will be held liable for payment of damages. All rights created by patent grant 10
or registration of a utility model or design patent are reserved.
Page 2 of 5
Index of Revisions
Rev. Date Remark Originator Reviewer Approver
0 04/21/2023 First Issue S. Fierro A. Ochoa J. Botero
R
es
tri
ct
ed
©
Si
e
m
en
s
E
ne
rg
y,
20
22
.
All
Ri
gh
ts
re
se
rv
ed
.
R
Insulators Selection Primary Engineering Team A
Page 3 of 5
Index:
1 Purpose.........................................................................................................................
2 Documents to be submitted with the bid...................................................................
3 Documents to be submitted during the project........................................................
4 Design requirements...................................................................................................
4.1 General..............................................................................................................................
4.2 Technical...........................................................................................................................
5 Required Test...............................................................................................................
5.1 General..............................................................................................................................
R
es
6 Standards......................................................................................................................
tri
ct 7 Contacts........................................................................................................................
ed
©
Si 8 List of Appendix...........................................................................................................
e
m
en
s List of Tables:
E
ne
rg
y, No table of figures entries found.
20
22
.
All List of Figures:
Ri
gh
ts
re
No table of figures entries found.
se
rv
ed
.
R
Page 4 of 5
1 Purpose
2 Insulators selection methodology

Insulators selection should consider all the different scenarios like wind conditions, pollution, short
circuit stress, and seismic activity in order to have a right mechanical performance for them. In
addition to the previous, the following aspects are also considered in the selection of insulators:
 Nominal voltage
 Maximum rated voltage
 BIL
 Safety air clearances
 Height above sea level
 Mechanical efforts
R
es According to IEC 60815-1, insulator selection and sizing can be performed under three
tri
ct
approaches.
ed The first of them contemplates the selection based on experience, the second uses measurements
©
Si
or estimates of the severity of contamination on site and laboratory tests, while the third
e methodology allows to size and select the insulator in concordance with typical environments, the
m
en present methodology is based on the third one.
s
E
ne
rg
2.1 Minimum creepage distance
y,
20 The minimum creepage distance of an insulator located between phase and ground is determined
22 according to the contamination level of the site, using the following formula:
.
All
Ri USCD∗U m
gh
MinCreepage distance phase ¿ groung=
ts
re √3
se
rv
ed Where:
.
Um, Max rated voltage.

USCD, Unified specific creepage distance.
And:
USCD=RUSCD∗K a∗K ad
RUSCD, Reference unified specific creepage distance.

Ka, Correction for altitude factor.
Kad, Correction for insulator diameter.
3 Standards
R
Page 5 of 5
4 Contacts
5 List of Appendix
R
es
tri
ct
ed
©
Si
e
m
en
s
E
ne
rg
y,
20
22
.
All
Ri
gh
ts
re
se
rv
ed
.
R

Insulator Selection

Uploaded by

Copyright:

Available Formats

Insulator Selection

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Insulator Selection

Uploaded by

Copyright:

Available Formats

Document No._Rev.

Insulators Selection Methodology

Export Control Classification:

Restricted © Siemens Energy, 2023

2 Insulators selection methodology

Um, Max rated voltage.

RUSCD, Reference unified specific creepage distance.

You might also like