C TRANSMISSION/TRANSAXLE

B
SECTION
MANUAL TRANSMISSION MT

E
CONTENTS
PRECAUTIONS .......................................................... 2 SHIFT CONTROL ..................................................... 13 F
Service Notice or Precautions .................................. 2 Removal and Installation ........................................ 13
PREPARATION ........................................................... 3 COMPONENTS ................................................... 13
Special Service Tools ............................................... 3 REMOVAL ........................................................... 13 G
Commercial Service Tools ........................................ 6 INSTALLATION ................................................... 13
NOISE, VIBRATION AND HARSHNESS (NVH) AIR BREATHER HOSE ............................................ 15
TROUBLESHOOTING ................................................ 7 Removal and Installation ........................................ 15
H
NVH Troubleshooting Chart ..................................... 7 TRANSMISSION ASSEMBLY .................................. 16
DESCRIPTION ............................................................ 8 Removal and Installation from Vehicle (For 2WD
Cross-Sectional View ............................................... 8 models) ................................................................... 16
DOUBLE-CONE SYNCHRONIZER ...................... 9 COMPONENTS ................................................... 16 I
TRIPLE-CONE SYNCHRONIZER ........................ 9 REMOVAL ........................................................... 17
M/T OIL ..................................................................... 10 INSTALLATION ................................................... 17
Changing ................................................................ 10 Removal and Installation from Vehicle (For 4WD J
DRAINING ........................................................... 10 models) ................................................................... 18
FILLING ............................................................... 10 COMPONENTS ................................................... 18
Checking ................................................................ 10 REMOVAL ........................................................... 18
K
OIL LEAKAGE AND OIL LEVEL ......................... 10 INSTALLATION ................................................... 19
REAR OIL SEAL .......................................................11 Disassembly and Assembly .................................... 21
Removal and Installation (For 2WD models) ..........11 COMPONENTS ................................................... 21
REMOVAL ............................................................11 DISASSEMBLY ................................................... 27 L
INSTALLATION ....................................................11 INSPECTION AFTER DISASSEMBLY ................ 41
POSITION SWITCH .................................................. 12 ASSEMBLY ......................................................... 45
Checking ................................................................ 12 SERVICE DATA AND SPECIFICATIONS (SDS) ...... 68 M
BACK-UP LAMP SWITCH .................................. 12 General Specifications ............................................ 68
PARK/NEUTRAL POSITION SWITCH ............... 12 Gear End Play ........................................................ 69
Snap Rings ............................................................. 69
Baulk Ring Clearance ............................................. 70

Revision: February 2006 MT-1 2005 Xterra

 PRECAUTIONS

PRECAUTIONS PFP:00001

Service Notice or Precautions ECS00DYO

● Do not reuse transmission oil once it has been drained.

● Check oil level or replace oil with vehicle on level surface.
● During removal or installation, keep inside of transmission clear of dust or dirt.
● Check for the correct installation status prior to removal or disassembly. If matching marks are required,
be certain they do not interfere with the function of the parts they are applied to.
● In principle, tighten nuts and bolts gradually in several steps working diagonally from inside to outside. If
tightening sequence is specified, use it.
● Be careful not to damage sliding surfaces and mating surfaces.

Revision: February 2006 MT-2 2005 Xterra

 PREPARATION

PREPARATION PFP:00002
A
Special Service Tools ECS00DYP

The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Tool number
B
(Kent-Moore No.) Description
Tool name
ST30911000 ● Installing mainshaft bearing
( — ) ● Installing 5th-6th synchronizer hub assem-
MT
Inserter bly
● Installing reverse main gear bushing
● Installing 3rd gear bushing D
● Installing 3rd-4th synchronizer hub assem-
bly
ZZA0920D
a: 98 mm (3.86 in) dia. E
b: 40 mm (1.57 in) dia.
ST30022000 ● Installing 3rd main gear
( — ) ● Installing 4th main gear F
Inserter
a: 110 mm (4.33 in) dia.
b: 46 mm (1.81 in) dia.
G
ZZA0920D

ST27861000 ● Installing 1st-2nd synchronizer hub assem- H

( — ) bly
Support ring ● Installing 1st gear bushing
a: 62 mm (2.44 in) dia.
b: 52 mm (2.05 in) dia. I

ZZA0832D

ST30032000 Installing counter rear bearing inner race

J
(J-26010-01) a: 80 mm (3.15 in) dia.
Inserter b: 31 mm (1.22 in) dia.
K

ZZA0920D L
KV32102700 Installing main drive gear bearing
( — ) a: 48 mm (1.89 in) dia.
Drift b: 41 mm (1.61 in) dia.
M

ZZA0534D

ST23860000 Installing reverse counter gear

( — ) a: 38 mm (1.50 in) dia.
Drift b: 33 mm (1.30 in) dia.

ZZA0534D

Revision: February 2006 MT-3 2005 Xterra

 PREPARATION

Tool number
(Kent-Moore No.) Description
Tool name
ST01530000 Installing reverse synchronizer hub assembly
( — ) a: 50 mm (1.97 in) dia.
Drift b: 41 mm (1.61 in) dia.

ZZA0534D

KV381054S0 Removing rear oil seal

(J-34286)
Puller

ZZA0601D

ST33200000 Installing counter rear bearing

(J-26082) a: 60 mm (2.36 in) dia.
Drift b: 44.5 mm (1.752 in) dia.

ZZA1002D

ST30621000 Installing dust seal

(J-25742-5) a: 79 mm (3.11 in) dia.
Drift b: 59 mm (2.32 in) dia.

ZZA1000D

KV40100630 Installing 4th counter gear thrust washer

(J-26092) a: 67 mm (2.64 in) dia.
Inserter b: 38 mm (1.50 in) dia.

ZZA0920D

KV38102100 Installing front cover oil seal

(J-25803-01) a: 44 mm (1.73 in) dia.
Drift b: 28 mm (1.10 in) dia.

NT084

KV32103300 Installing reverse synchronizer hub assembly

(J-46529) a: 73 mm (2.87 in)
Press plate

PCIB0165J

Revision: February 2006 MT-4 2005 Xterra

 PREPARATION

Tool number
(Kent-Moore No.) Description A
Tool name
ST30031000 Measuring wear of inner baulk ring
(J-22912-01) B
Puller

MT

ZZC0499D

ST22490000 Holding a adapter plate D

( — )
Adapter setting plate

ZZC0465D

ST33400001 Installing oil seal

F
(J-26082) a: 60 mm (2.36 in) dia.
Drift b: 47 mm (1.85 in) dia.
G

NT086 H

Revision: February 2006 MT-5 2005 Xterra

 PREPARATION

Commercial Service Tools ECS00DYQ

Tool name Description

Puller Removing each bearing, gear and bushing

ZZB0823D

Pin punch Removing and installing each retaining pin

Tip diameter: 6.0 mm (0.236 in) dia.

ZZA0815D

Power tool Loosening bolts and nuts

PBIC0190E

Puller ● Removing reverse synchronizer hub as-

sembly
● Removing reverse counter gear
● Removing reverse main gear

NT077

Drift Removing counter end bearing

a: 32 mm (1.26 in) dia.

LCIA0362E

Revision: February 2006 MT-6 2005 Xterra

 NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING

NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING PFP:00003

A
NVH Troubleshooting Chart ECS00DYR

Use the chart below to help you find the cause of the symptom. The numbers indicate the order of the inspec-
tion. If necessary, repair or replace these parts. B

MT-10

MT-21

MT-13

MT-25

MT-23
Reference page

MT

CHECK PLUG RETURN SPRING AND CHECK BALL (Worn or damaged)

D

F
SUSPECTED PARTS
(Possible cause)

SHIFT CONTROL LINKAGE (Worn)

G

BAULK RING (Worn or damaged)

BEARING (Worn or damaged)
OIL SEAL (Worn or damaged)

INSERT SPRING (Damaged)

GEAR (Worn or damaged)
H
OIL (Oil level is high.)

GASKET (Damaged)

SHIFT FORK (Worn)

OIL (Oil level is low.)

OIL (Wrong oil.)

J
Noise 1 2 3 3
Oil leakage 3 1 2 2
Symptoms K
Hard to shift or will not shift 1 1 2 2 2
Jumps out of gear 1 1 2 2
L

Revision: February 2006 MT-7 2005 Xterra

 DESCRIPTION

DESCRIPTION PFP:00000

Cross-Sectional View ECS00DYS

PCIB1297E

1. Mainshaft 2. Reverse synchronizer hub 3. Reverse coupling sleeve

4. Reverse main gear 5. 4th main gear 6. 3rd main gear
7. 1st main gear 8. 1st-2nd coupling sleeve 9. 1st-2nd synchronizer hub
10. 2nd main gear 11. 6th main gear 12. 5th-6th coupling sleeve
13. 5th-6th synchronizer hub 14. Main drive gear 15. Front cover
16. Transmission case 17. Counter gear 18. Filler plug
19. 3rd counter gear 20. 3rd-4th synchronizer hub 21. 3rd-4th coupling sleeve
22. Drain plug 23. Adapter plate 24. 4th counter gear
25. Reverse idler gear 26. Reverse idler shaft 27. Reverse counter gear
28. OD gear case 29. Rear extension

Revision: February 2006 MT-8 2005 Xterra

 DESCRIPTION

DOUBLE-CONE SYNCHRONIZER
The 1st and 3rd, 4th gears is equipped with a double-cone synchronizer to reduce the operating force of the A
shift lever.
TRIPLE-CONE SYNCHRONIZER
B
The 2nd gear is equipped with a triple-cone synchronizer to reduce the operating force of the shift lever.

MT

E
PCIB0594E

Revision: February 2006 MT-9 2005 Xterra

 M/T OIL

M/T OIL PFP:KLD20

Changing ECS00DYT

DRAINING
1. Start the engine and let it run to warm up the transmission.
2. Stop the engine. Remove the transmission drain plug and drain the oil.
3. Set a gasket on the drain plug and install it to the transmission. Tighten the drain plug to the specified
torque. Refer to MT-21, "Case Components" .
CAUTION:
Do not reuse gasket.
FILLING
1. Remove the filler plug. Fill with new oil until oil level reaches the specified limit near the filler plug hole.
Oil grade and Viscosity : Refer to MA-11, "Fluids and Lubricants" .
Oil capacity : Refer to MA-11, "Fluids and Lubricants" .
2. After refilling the oil, check oil level. Set a gasket to the filler plug, then install it to the transmission.
Tighten the filler plug to the specified torque. Refer to MT-21, "Case Components" .
CAUTION:
Do not reuse gasket.
Checking ECS00DYU

OIL LEAKAGE AND OIL LEVEL

● Make sure that oil is not leaking from the transmission or around it.
● Check oil level from the filler plug hole as shown.
CAUTION:
Do not start engine while checking oil level.
● Set a gasket on the filler plug and install it to the transmission.
Tighten the filler plug to the specified torque. Refer to MT-21,
"Case Components" .
CAUTION:
Do not reuse gasket.

PCIB0268E

Revision: February 2006 MT-10 2005 Xterra

 REAR OIL SEAL

REAR OIL SEAL PFP:33140

A
Removal and Installation (For 2WD models) ECS00DYV

REMOVAL
1. Remove rear propeller shaft. Refer to PR-10, "Removal and
B
Installation" .
2. Remove dust seal and rear oil seal using suitable tool.
CAUTION: MT
● Do not damage rear extension assembly.

● Do not reuse dust seal and rear oil seal.

LCIA0383E
E
INSTALLATION
Installation is the reverse order of removal.
● Drive the new rear oil seal (1) and dust seal (2) using Tool A. F
Tool number : ST33400001 (J-26082)

Dimension B : 0.5 - 1.5 mm (0.020 - 0.059 in) G

Dimension C : 1.2 - 2.2 mm (0.047 - 0.087 in)
CAUTION: H
● Do not reuse dust seal and rear oil seal.

● Apply multi-purpose grease to seal lips before installing.

● Do not incline the dust seal and rear oil seal during instal-
I
lation.
● Check the transmission oil level after installation. Refer to MT-
10, "Checking" .
J

WCIA0553E

Revision: February 2006 MT-11 2005 Xterra

 POSITION SWITCH

POSITION SWITCH PFP:32005

Checking ECS00DYW

BACK-UP LAMP SWITCH

● Check continuity.
Gear position Continuity
Reverse Yes
Except reverse No

SCIA0645E

PARK/NEUTRAL POSITION SWITCH

● Check continuity.
Gear position Continuity
Neutral Yes
Except neutral No

Revision: February 2006 MT-12 2005 Xterra

 SHIFT CONTROL

SHIFT CONTROL PFP:34103

A
Removal and Installation ECS00DYX

COMPONENTS
B

MT

M
WCIA0508E

1. Retaining plate 2. Dust boot cover (upper) 3. Dust boot cover (lower)
4. Shift knob 5. Shift lever assembly 6. Clip (A)
7. Boot 8. Guide plate 9. Socket
10. Bushing 11. Clip (B) 12. Spring

REMOVAL
1. Remove the shift knob.
2. Remove the M/T finisher. Refer to IP-13, "M/T FINISHER" .
3. Remove the retaining plate and dust boot covers.
4. Remove the clip (B) and then separate the boot from the control housing.
5. Remove the guide plate bolts and then separate the guide plate.
6. Remove the shift lever assembly and spring from the transmission.
INSTALLATION
Installation is the reverse order of removal.

Revision: February 2006 MT-13 2005 Xterra

 SHIFT CONTROL

CAUTION:
● Apply multi-purpose grease to the socket and bushing.
● Do not reuse clip.
● Apply cement to threads of the shift lever assembly.
● Temporarily tighten guide plate bolts. Then tighten guide plate
bolts to the specified torque in the order shown. Refer to MT-13,
"COMPONENTS" .
● When shift lever assembly is shifted to each position, make sure
there is no binding or disconnection in either boot.
● When shifted to each position, make sure there is no noise,
bending, and backlash. Especially when shift lever assembly is
shifted to 5th, 6th without pressing downward, check for bend-
ing.
● When shift lever assembly is shifted to 1st, 2nd side and 5th, 6th
side, confirm shift lever assembly returns to neutral position LCIA0398E

smoothly.
● In any position other than reverse, confirm that shift lever assembly can be pressed downward.
● With shift lever assembly pressed downward, confirm that it can be shifted to reverse.
● When shifted from reverse to neutral position, confirm shift lever assembly returns to neutral position
smoothly with spring power.
● Without shift lever assembly pressed downward, confirm that it cannot be shifted to reverse.

Revision: February 2006 MT-14 2005 Xterra

 AIR BREATHER HOSE

AIR BREATHER HOSE PFP:31098

A
Removal and Installation ECS00DYY

Refer to the figure below for air breather hose removal and installation information.
B

MT

K
LCIA0392E

1. Water outlet 2. Bracket 3. Air breather hose

4. Breather tube L
CAUTION:
● Make sure there are no pinched or blocked areas on the air breather hose after installation.
● When inserting the air breather hose, be sure to insert it fully until its end reaches the end of the M
tube radius.
● Install the air breather hose with the paint mark side up.

Revision: February 2006 MT-15 2005 Xterra

 TRANSMISSION ASSEMBLY

TRANSMISSION ASSEMBLY PFP:32010

Removal and Installation from Vehicle (For 2WD models) ECS00DYZ

COMPONENTS

LCIA0394E

1. Transmission assembly 2. Crossmember 3. Insulator

4. Dynamic damper

Revision: February 2006 MT-16 2005 Xterra

 TRANSMISSION ASSEMBLY

REMOVAL
1. Drain transmission oil. Refer to MT-10, "DRAINING" . A
2. Disconnect the battery cable from the negative terminal.
3. Remove the shift lever assembly. Refer to MT-13, "Removal and Installation" .
B
4. Remove the LH fender protector. Refer to EI-19, "FENDER PROTECTOR" .
5. Remove the crankshaft position sensor (POS) from M/T assem-
bly.
MT
CAUTION:
Do not damage the sensor edge.
6. Remove the undercovers using power tool.
D
7. Remove the front crossmember using power tool.
8. Remove the starter motor. Refer to SC-22, "Removal and Instal-
lation" .
E
9. Remove the rear propeller shaft. Refer to PR-10, "Removal and
Installation" . LCIA0367E

10. Remove the left and right front exhaust tubes. Refer to EX-3,
F
"Removal and Installation" .
11. Remove the clutch operating cylinder from the transmission. Refer to CL-11, "Removal and Installation" .
12. Support the transmission using a suitable jack.
G
13. Remove the nuts securing the insulator to the crossmember.
14. Remove the crossmember using power tool.
WARNING: H
Support the transmission using suitable jack.
15. Tilt the transmission slightly to gain clearance between the body and the transmission, then disconnect
the air breather hoses. Refer to MT-15, "Removal and Installation" . I
16. Disconnect the following:
● Back-up lamp switch connector

● Park/neutral position (PNP) switch connector J

17. Remove the wiring harness from the retainers.
18. Remove the transmission to engine bolts using power tool.
19. Separate the transmission from the engine and remove it from the vehicle. K
WARNING:
Support the transmission while removing it using suitable jack.
L
INSTALLATION
Installation is the reverse order of removal.
● When installing the transmission to the engine, tighten the bolts M
to the specified torque.
Quantity 10

Bolt length “ ”
65 (2.56)
mm (in)
Tightening torque
75 (7.7, 55)
N·m (kg-m, ft-lb)

CAUTION:
● When installing be careful to avoid interference between
WCIA0507E
transmission main drive gear and clutch cover.
● After installation, check for oil leakage and oil level. Refer to MT-10, "Checking" .
● If flywheel is removed, align dowel pin with the smallest hole of flywheel. Refer to EM-112,
"ASSEMBLY" .
● When replacing an engine or transmission you must make sure the dowels are installed correctly
during re-assembly.

Revision: February 2006 MT-17 2005 Xterra

 TRANSMISSION ASSEMBLY

● Improper alignment caused by missing dowels may cause vibration, oil leaks or breakage of drive
train components.
Removal and Installation from Vehicle (For 4WD models) ECS00DZ0

COMPONENTS

LCIA0393E

1. Transmission assembly 2. Crossmember 3. Insulator

REMOVAL
1. Drain transmission oil. Refer to MT-10, "DRAINING" .
Revision: February 2006 MT-18 2005 Xterra
 TRANSMISSION ASSEMBLY

2. Disconnect the battery cable from the negative terminal.

3. Remove the shift lever assembly. Refer to MT-13, "Removal and Installation" . A
4. Remove the LH fender protector. Refer to EI-19, "FENDER PROTECTOR" .
5. Remove the crankshaft position sensor (POS) from the M/T
assembly. B
CAUTION:
Do not damage the sensor edge.
6. Remove the undercovers using power tool. MT
7. Remove the front crossmember using power tool.
8. Remove the starter motor. Refer to SC-22, "Removal and Instal-
lation" . D
9. Remove the front and rear propeller shafts. Refer to PR-5,
"Removal and Installation" and PR-10, "Removal and Installa- LCIA0367E
tion" . E
10. Remove the left and right front exhaust tubes. Refer to EX-3, "Removal and Installation" .
11. Remove the clutch operating cylinder from the transmission. Refer to CL-11, "Removal and Installation" .
F
12. Support the transmission using a suitable jack.
13. Remove the nuts securing the insulator to the crossmember.
14. Remove the crossmember using power tool. G
WARNING:
Support the transmission using suitable jack.
15. Tilt the transmission slightly to gain clearance between the body and the transmission, then disconnect H
the air breather hoses. Refer to MT-15, "Removal and Installation" .
16. Disconnect the following:
● Back-up lamp switch connector I
● Park/neutral position (PNP) switch connector

● ATP switch connector

● Neutral 4LO switch connector J

● Wait detection switch connector

● Transfer control device connector

17. Remove the wiring harness from the retainers. K

18. Remove the transmission to engine bolts using power tool.
19. Separate the transmission from the engine and remove it from the vehicle.
L
WARNING:
Support manual transmission while removing it.
INSTALLATION M
Installation is the reverse order of removal.
● When installing the transmission to the engine, tighten the bolts
to the specified torque.
Quantity 10

Bolt length “ ”
65 (2.56)
mm (in)
Tightening torque
75 (7.7, 55)
N·m (kg-m, ft-lb)
CAUTION:
● When installing be careful to avoid interference between
WCIA0507E
transmission main drive gear and clutch cover.
● After installation, check for oil leakage and oil level. Refer to MT-10, "Checking" .
● If flywheel is removed, align dowel pin with the smallest hole of flywheel. Refer to EM-112,
"ASSEMBLY" .

Revision: February 2006 MT-19 2005 Xterra

 TRANSMISSION ASSEMBLY

● When replacing an engine or transmission you must make sure the dowels are installed correctly
during re-assembly.
● Improper alignment caused by missing dowels may cause vibration oil leaks or breakage of driv-
etrain components.

Revision: February 2006 MT-20 2005 Xterra

 TRANSMISSION ASSEMBLY

Disassembly and Assembly ECS00DZ1

COMPONENTS A
Case Components

MT

PCIB1208E

1. Front cover gasket 2. Front cover 3. Washer

4. Withdrawal lever ball pin 5. Front cover oil seal 6. Pivot bolt
7. Check shift pin 8. Filler plug 9. Gasket
10. Transmission case 11. Drain plug 12. Sliding ball bearing
13. Bushing 14. Oil gutter 15. Breather
16. Dowel pin 17. Magnet 18. Baffle plate
19. Adapter plate 20. Baffle plate 21. Bearing retainer

Revision: February 2006 MT-21 2005 Xterra

 TRANSMISSION ASSEMBLY

PCIB1209E

1. Control housing 2. Gasket 3. Plunger

4. Park/neutral position (PNP) switch 5. Clip 6. Back-up lamp switch
7. Sliding ball bearing 8. Bushing 9. Rear extension oil gutter
10. Cap 11. Counter end bearing 12. Rear extension
13. Rear oil seal 14. Dust seal 15. Dowel pin
16. OD gear case

Revision: February 2006 MT-22 2005 Xterra

 TRANSMISSION ASSEMBLY

Gear Components
A

MT

L
PCIB1210E

1. Snap ring 2. Main drive gear bearing 3. Main drive gear

4. Main pilot bearing 5. Pilot bearing spacer 6. 5th baulk ring M
7. 5th-6th spread spring 8. 5th-6th shifting insert 9. 5th-6th synchronizer hub
10. 5th-6th coupling sleeve 11. 6th baulk ring 12. 6th needle bearing
13. 6th main gear 14. Mainshaft 15. 2nd needle bearing
16. 2nd main gear 17. 2nd inner baulk ring 18. 2nd synchronizer cone
19. 2nd outer baulk ring 20. 1st-2nd spread spring 21. 1st-2nd shifting insert
22. 1st-2nd synchronizer hub 23. 1st-2nd coupling sleeve 24. 1st outer baulk ring
25. 1st synchronizer cone 26. 1st inner baulk ring 27. 1st gear bushing
28. 1st needle bearing 29. 1st main gear 30. 3rd main gear
31. 3rd-4th main spacer 32. 4th main gear 33. Mainshaft bearing
34. Reverse main gear bushing 35. Reverse main needle bearing 36. Reverse main gear
37. Reverse baulk ring 38. Reverse spread spring 39. Reverse shifting insert
40. Reverse synchronizer hub 41. Reverse coupling sleeve

Revision: February 2006 MT-23 2005 Xterra

 TRANSMISSION ASSEMBLY

PCIB1211E

1. Counter front bearing 2. Counter gear 3. 3rd gear bushing

4. 3rd needle bearing 5. 3rd counter gear 6. 3rd inner baulk ring
7. 3rd synchronizer cone 8. 3rd outer baulk ring 9. 3rd-4th spread spring
10. 3rd-4th shifting insert 11. 3rd-4th synchronizer hub 12. 3rd-4th coupling sleeve
13. 4th outer baulk ring 14. 4th synchronizer cone 15. 4th inner baulk ring
16. 4th gear bushing 17. 4th needle bearing 18. 4th counter gear
19. 4th counter gear thrust washer 20. Counter rear bearing inner race 21. Counter rear bearing
22. Counter rear bearing spacer 23. Reverse counter gear 24. Snap ring
25. Counter end bearing 26. Reverse idler shaft 27. Reverse idler needle bearing
28. Reverse idler gear 29. Reverse idler thrust washer

Revision: February 2006 MT-24 2005 Xterra

 TRANSMISSION ASSEMBLY

Shift Control Components

A

MT

J
PCIB1212E

1. Check ball plug 2. Check ball spring 3. Check ball

4. Interlock pin 5. Interlock plunger 6. Retaining pin K
7. 3rd-4th fork rod bracket 8. 3rd-4th fork rod 9. 1st-2nd fork rod
10. 1st-2nd shift fork 11. 3rd-4th fork rod (reversal side) 12. 3rd-4th shift fork
13. 5th-6th shift fork 14. 5th-6th fork rod (reversal side) 15. 5th-6th fork rod L
16. 5th-6th fork rod bracket 17. 3rd-4th control lever 18. Shifter cap
19. 5th-6th control lever 20. Adapter plate
M

Revision: February 2006 MT-25 2005 Xterra

 TRANSMISSION ASSEMBLY

PCIB1213E

1. Return spring plunger 2. Return spring 3. Return spring plug

4. Striking arm 5. Retaining pin 6. Stopper ring
7. Striking rod assembly 8. Adapter plate 9. Reverse fork rod
10. Reverse shift fork 11. Rear extension 12. OD gear case

Revision: February 2006 MT-26 2005 Xterra

 TRANSMISSION ASSEMBLY

DISASSEMBLY
Case Components A
1. Remove clips from PNP switch and back-up lamp switch.
2. Remove PNP switch, back-up lamp switch and plungers from
rear extension (or OD gear case). B

MT

D
PCIB1215E

3. Remove control housing bolts, and then remove control housing E

and gasket from rear extension (or OD gear case).

PCIB1216E H

4. Remove return spring plug, return spring and return spring

plunger from rear extension (or OD gear case).
I

PCIB1643E

L
5. Remove rear oil seal from OD gear case using Tool. (For 4WD
models)
CAUTION:
Be careful not to damage OD gear case. M

PCIB1218E

Revision: February 2006 MT-27 2005 Xterra

 TRANSMISSION ASSEMBLY

6. Remove retaining pin using suitable tool, and then remove strik-
ing arm from striking rod assembly.

PCIB1219E

7. Remove rear extension (or OD gear case) bolts, and then

remove rear extension (or OD gear case) from adapter plate
using suitable tool.

PCIB1220E

8. Remove rear extension oil gutter bolt, and then remove rear
extension oil gutter and cap from rear extension. (For 2WD mod-
els)

PCIB1221E

9. Remove dust seal and rear oil seal from rear extension using
suitable tool. (For 2WD models)
CAUTION:
Be careful not to damage rear extension.

PCIB1222E

10. Remove counter end bearing from rear extension (or OD gear
case) using suitable tool.
CAUTION:
Be careful not to damage rear extension (or OD gear case).

PCIB1223E

Revision: February 2006 MT-28 2005 Xterra

 TRANSMISSION ASSEMBLY

11. Remove withdrawal lever ball pin and washer from front cover.
A

MT

PCIB1224E
D
12. Remove front cover bolts, and then remove front cover and
front cover gasket from transmission case.
E

G
PCIB1225E

13. Remove front cover oil seal from front cover using suitable tool. H
CAUTION:
Be careful not to damage front cover.
I

SCIA1399E K

14. Remove baffle plate nut from transmission case.

L

SCIA1443E

15. Remove snap ring from main drive gear bearing using suitable
tool.

SCIA1532E

Revision: February 2006 MT-29 2005 Xterra

 TRANSMISSION ASSEMBLY

16. Remove pivot bolt and check shift pin from transmission case.

PCIB1226E

17. Remove transmission case from adapter plate.

PCIB1227E

18. Remove counter front bearing from transmission case.

PCIB0436E

19. Remove oil gutter from transmission case.

PCIB1228E

20. Remove filler plug and gasket from transmission case.

PCIB1229E

Revision: February 2006 MT-30 2005 Xterra

 TRANSMISSION ASSEMBLY

Shift Control Components

A
1. Remove rear extension (or OD gear case) and transmission case. Refer to MT-27, "Case Components" .

2. Install Tool to adapter plate, and then position in a vise.

CAUTION: B
Do not directly secure mating surface of adapter plate in a
vise.
MT

PCIB1230E
E
3. Remove baffle plate bolts, and then remove baffle plate from
adapter plate.
F

H
PCIB1325E

4. Remove check ball plugs, check ball springs and check balls I
from adapter plate.

PCIB1231E L

5. Remove 3rd-4th control lever bolts, and then remove 3rd-4th

control lever and shifter cap from adapter plate.
M

PCIB1232E

Revision: February 2006 MT-31 2005 Xterra

 TRANSMISSION ASSEMBLY

6. Remove retaining pin using suitable tool, and then remove 3rd -
4th fork rod bracket and 3rd-4th fork rod from adapter plate.

PCIB0145E

7. Remove check balls and interlock pin from adapter plate.

PCIB0146E

8. Remove retaining pin using a suitable tool, and then remove

3rd-4th shift fork and 3rd-4th fork rod (reversal side) from
adapter plate.

PCIB0601E

9. Remove retaining pin using a suitable tool, and then remove 1st-
2nd shift fork and 1st-2nd fork rod from adapter plate.

PCIB0602E

10. Remove interlock plunger and interlock pin from adapter plate.

PCIB0147E

Revision: February 2006 MT-32 2005 Xterra

 TRANSMISSION ASSEMBLY

11. Remove retaining pin using suitable tool, and then remove
reverse shift fork and reverse fork rod from adapter plate. A

MT

SCIA1447E
D
12. Remove check balls from adapter plate.

G
PCIB0148E

13. Remove retaining pin using suitable tool, and then remove 5th- H
6th fork rod bracket and 5th-6th fork rod from adapter plate.

PCIB0239E K

14. Remove 5th-6th control lever bolts, and then remove 5th-6th
control lever from adapter plate.
L

PCIB1233E

15. Remove retaining pin using suitable tool, and then remove 5th-
6th shift fork and 5th-6th fork rod (reversal side) from adapter
plate.

PCIB0412E

Revision: February 2006 MT-33 2005 Xterra

 TRANSMISSION ASSEMBLY

16. Remove retaining pin using suitable tool, and then remove stop-
per ring from striking rod assembly.

PCIB1234E

17. Remove striking rod assembly from adapter plate.

PCIB1235E

Gear Components
1. Remove rear extension (or OD gear case) and transmission case. Refer to MT-27, "Case Components" .
2. Remove shift forks and fork rods. Refer to MT-31, "Shift Control Components" .
3. Before disassembling, measure the end play for each position. If the end play is outside the standards,
disassemble and inspect.
● Main drive gear

End play : 0 - 0.10 mm (0 - 0.004 in)

PCIB0484E

● Mainshaft (Rear side)

End play : 0 - 0.10 mm (0 - 0.004 in)

PCIB0225E

Revision: February 2006 MT-34 2005 Xterra

 TRANSMISSION ASSEMBLY

● Counter gear
End play : 0 - 0.10 mm (0 - 0.004 in) A

MT

PCIB0226E

D
4. Remove revers idler gear according to the following.
a. Remove reverse idler shaft assembly from adapter plate.
b. Remove reverse idler thrust washer, revers idler gear and E
reverse idler needle bearing from reverse idler shaft.

PCIB1326E

H
5. Remove reverse main gear and reverse synchronizer hub assembly according to the following.
a. Remove snap ring from mainshaft using suitable tool.
I

PCIB1236E

b. Remove reverse main gear and reverse synchronizer hub L

assembly using suitable tool.
c. Remove reverse main needle bearing from mainshaft.
M

SCIA1683E

6. Remove reverse coupling sleeve according to the following.

Revision: February 2006 MT-35 2005 Xterra

 TRANSMISSION ASSEMBLY

a. Remove snap ring from reverse synchronizer hub.

b. Remove spread springs and shifting inserts from reverse syn-
chronizer hub.
c. Remove reverse coupling sleeve from reverse synchronizer
hub.

PCIB1237E

7. Remove reverse counter gear according to the following.

a. Remove snap ring from counter gear using suitable tool.

PCIB1239E

b. Remove reverse counter gear using suitable tool.

8. Remove counter rear bearing spacer from counter gear.

SCIA1682E

9. Remove bearing retainer bolts, and then remove bearing

retainer.

PCIB1238E

10. Remove main drive gear assembly, mainshaft assembly and counter gear assembly according to the fol-
lowing.

Revision: February 2006 MT-36 2005 Xterra

 TRANSMISSION ASSEMBLY

a. Remove snap ring from mainshaft bearing using suitable tool.

A

MT

SCIA1691E

D
b. Carefully tap mainshaft using suitable tool, and then remove
main drive gear assembly, mainshaft assembly and counter
gear assembly from adapter plate.
E
c. Remove main pilot bearing, pilot bearing spacer from mainshaft.
d. Remove 5th baulk ring from main drive gear.
F

G
SCIA1456E

11. Remove counter rear bearing from adapter plate.

H

PCIB0244E
K
12. Remove magnet from adapter plate.

PCIB1240E

13. Remove baffle plate bolt, and then remove baffle plate from
adapter plate.

PCIB1241E

Revision: February 2006 MT-37 2005 Xterra

 TRANSMISSION ASSEMBLY

14. Remove breather from adapter plate.

PCIB1242E

15. Remove main drive gear bearing according to the following.

a. Remove snap ring from main drive gear using suitable tool.

SCIA1461E

b. Press out main drive gear bearing using suitable tool.

SCIA1533E

16. Before disassembling, measure the end play for mainshaft

(Front side). If the end play is outside the standards, disassem-
ble and inspect.
End play : 0 - 0.10 mm (0 - 0.004 in)

PCIB1243E

Revision: February 2006 MT-38 2005 Xterra

 TRANSMISSION ASSEMBLY

17. Press out reverse main gear bushing, mainshaft bearing and 4th
main gear using suitable tool. A
18. Remove 3rd-4th main spacer from mainshaft.

MT

SCIA1386E

D
19. Remove 3rd main gear and 1st main gear according to the following.
a. Press out 3rd main gear and 1st main gear using suitable tool.
CAUTION: E
Be careful not to damage 1st outer baulk ring.
b. Remove 1st needle bearing from mainshaft.
F

SCIA1458E

H
20. Remove 1st-2nd synchronizer hub assembly and 2nd main gear according to the following.
a. Press out 1st gear bushing, 1st-2nd synchronizer hub assembly
and 2nd main gear using suitable tool. I
CAUTION:
Be aware that when using the press, if mainshaft gear posi-
tioner catches on the V-block, etc., mainshaft could be dam-
aged. J
b. Remove 2nd needle bearing from mainshaft.
21. Remove 1st-2nd coupling sleeve according to the following.
K
a. Remove spread springs and shifting inserts from 1st-2nd syn-
chronizer hub. SCIA1459E
b. Remove 1st-2nd coupling sleeve from 1st-2nd synchronizer L
hub.

22. Remove 6th main gear and 5th-6th synchronizer hub assembly according to the following.
a. Remove snap ring from mainshaft using suitable tool. M

PCIB1244E

Revision: February 2006 MT-39 2005 Xterra

 TRANSMISSION ASSEMBLY

b. Press out 6th main gear and 5th-6th synchronizer hub assembly
using suitable tool.
c. Remove 6th needle bearing from mainshaft.
23. Remove 5th-6th coupling sleeve according to the following.
a. Remove spread springs and shifting inserts from 5th-6th syn-
chronizer hub.
b. Remove 5th-6th coupling sleeve from 5th-6th synchronizer hub.

SCIA1460E

24. Remove 3rd counter gear, 3rd-4th synchronizer hub assembly, 4th counter gear according to the follow-
ing.
a. Press out 3rd counter gear, 3rd-4th synchronizer hub assembly,
4th counter gear, 4th needle bearing, 4th gear bushing, 4th
counter gear thrust washer, and counter rear bearing inner race
using suitable tool.
b. Remove 3rd needle bearing from counter gear.
25. Remove 3rd-4th coupling sleeve according to the following.
a. Remove spread springs and shifting inserts from 3rd-4th syn-
chronizer hub.
b. Remove 3rd-4th coupling sleeve from 3rd-4th synchronizer hub.
SCIA1389E

26. Press out 3rd gear bushing using suitable tool.

CAUTION:
Do not use oil hole of 3rd gear bushing when press out.

PCIB1327E

Revision: February 2006 MT-40 2005 Xterra

 TRANSMISSION ASSEMBLY

INSPECTION AFTER DISASSEMBLY

Shift Control A
If the contact surface on striking lever, fork rod, shift fork, etc., has
excessive wear, abrasion, bend, or any other damage, replace the
components. B

MT

PCIB1245E H
Gear and Shaft
If the contact surface on each gear, mainshaft, main drive gear, and
counter gear, etc., has damage, peeling, abrasion, dent, bent, or any I
other damage, replace the components.

SCIA1680E
L

PCIB1246E

Revision: February 2006 MT-41 2005 Xterra

 TRANSMISSION ASSEMBLY

Synchronizer
● If the contact surface on coupling sleeve, synchronizer hub, and
shifting insert has damage or abrasion, replace the components.
● Coupling sleeve and synchronizer hub shall move smoothly.

SMT387A

● If the cam surface on baulk ring or contact surface on insert has

damage or excessive wear, replace with a new one.
● If spread spring damaged, replace with a new one.

SCIA0608J

Baulk Ring Clearance

● Single Cone Synchronizer (5th and 6th)
Push baulk ring on the cone, and measure the clearance
between baulk ring and cone. If the measurement is below limit,
replace it with a new one.
Clearance
Standard value : 0.7 - 1.35 mm (0.028 - 0.0531 in)
Limit value : 0.5 mm (0.020 in)

PCIB1328E

● Double Cone Synchronizer (1st, 3rd and 4th)

Check the clearance between outer baulk ring, synchronizer
cone, and inner baulk ring as follows.
CAUTION:
The clearances “A” and “B” are controlled with outer baulk
ring, synchronizer cone, and inner baulk ring as a set.
Replace them as a set if the clearances are outside the limit
value.

SCIA1679E

Revision: February 2006 MT-42 2005 Xterra

 TRANSMISSION ASSEMBLY

1. Measure the clearance “A” at 2 points or more diagonally oppo-

site using a dial indicator and Tool. Then calculate the mean A
value.
Clearance “A”
Standard value : 0.5 - 0.7 mm (0.020 - 0.028 in) B
Limit value : 0.3 mm (0.012 in)

MT

PCIB0945E

D
2. Measure the clearance “B” at 2 points or more diagonally oppo-
site using a feeler gauge. Then calculate the mean value.
Clearance “B” E
Standard value
1st : 1.0 - 1.5 mm (0.039 - 0.059 in)
3rd,4th : 0.85 - 1.35 mm (0.0335 - 0.0531 in) F
Limit value : 0. 7 mm (0.028 in)

G
SCIA1084E

● Triple Cone Synchronizer (2nd)

Check the clearance between outer baulk ring, synchronizer H
cone, and inner baulk ring as follows.
CAUTION:
The clearances “A”, “B” and “C” are controlled with outer I
baulk ring, synchronizer cone, and inner baulk ring as a set.
Replace them as a set if the clearances are outside the limit
value.
J

PCIB0603E

K
1. Measure the clearance “A” at 2 points or more diagonally oppo-
site using a feeler gauge when pressing baulk ring toward clutch
gear taper cone. Then calculate the mean value. L
Clearance “A”
Standard value : 0.6 - 1.3 mm (0.024 - 0.051 in)
Limit value : 0.3 mm (0.012 in) M

PCIB0887E

2. Measure the clearance “B” at 2 points or more diagonally oppo-

site using a feeler gauge. Then calculate the mean value.
Clearance “B”
Standard value : 0.85 - 1.35 mm (0.0335 - 0.0531 in)
Limit value : 0.7 mm (0.028 in)

PCIB1329E

Revision: February 2006 MT-43 2005 Xterra

 TRANSMISSION ASSEMBLY

3. Measure the clearance “C” at 2 points or more diagonally oppo-

site using a feeler gauge when pressing baulk ring toward clutch
gear taper cone. Then calculate the mean value.
Clearance “C”
Standard value : 0.7 - 1.25 mm (0.028 - 0.0492 in)
Limit value : 0.3 mm (0.012 in)

PCIB0888E

● Reverse Synchronizer
Push baulk ring on the cone, and measure the clearance
between baulk ring and cone. If the measurement is below limit,
replace it with a new one.
Clearance
Standard value : 0.75 - 1.2 mm (0.0295 - 0.047 in)
Limit value : 0.5 mm (0.020 in)

PCIB1328E

Bearing
If the bearing does not rotate smoothly or the contact surface on ball
or race is damaged or peeled, replace with new ones.

SMT418A

Revision: February 2006 MT-44 2005 Xterra

 TRANSMISSION ASSEMBLY

ASSEMBLY
Gear Components A
1. Install 5th-6th synchronizer hub assembly according to the following.
a. Install 5th-6th coupling sleeve to 5th-6th synchronizer hub.
B
CAUTION:
● Do not reuse 5th-6th synchronizer hub and 5th-6th coupling sleeve.

● Replace 5th-6th synchronizer hub and 5th-6th coupling sleeve as a set.

MT
● Be careful with the orientation 5th-6th coupling sleeve.

F
PCIB1247E

● Be careful with the orientation 5th-6th synchronizer hub.

G

PCIB1248E
J
b. Install shifting inserts and spread springs to 5th-6th synchronizer
hub.
CAUTION: K
● Do not install spread spring hook onto the same shifting
insert.
L

M
SCIA1600E

● Be careful with the shape of reserve shifting insert to

avoid misemploy.

PCIB0608E

Revision: February 2006 MT-45 2005 Xterra

 TRANSMISSION ASSEMBLY

c. Press in 5th-6th synchronizer hub assembly, 6th baulk ring, 6th

main gear and 6th needle bearing using Tool.
CAUTION:
● Apply gear oil to 6th baulk ring and 6th needle bearing.

● Be careful with the orientation 5th-6th coupling sleeve.

PCIB1249E

NOTE:
5th and 6th baulk rings have three spaces that four gear teeth
are missing as shown.

PCIB1330E

2. Select and install a snap ring so that the end play comes within
the standard value. Refer to MT-69, "Snap Rings" .
End play : 0 - 0.10 mm (0 - 0.004 in)
CAUTION:
Do not reuse snap ring.

PCIB0609E

3. Install 1st-2nd synchronizer hub assembly according to the following.

a. Install 1st-2nd coupling sleeve to 1st-2nd synchronizer hub.
CAUTION:
● Do not reuse 1st-2nd coupling sleeve and 1st-2nd synchronizer hub.

● Replace 1st-2nd synchronizer hub and 1st-2nd coupling sleeve as a set.

● Be careful with the orientation 1st-2nd coupling sleeve.

PCIB1250E

Revision: February 2006 MT-46 2005 Xterra

 TRANSMISSION ASSEMBLY

● Be careful with the orientation 1st-2nd synchronizer hub.

A

MT

PCIB1251E

D
b. Install spread springs and shifting inserts to 1st-2nd synchro-
nizer hub.
CAUTION: E
● Do not install spread spring hook onto the same shifting
insert.
F

G
SCIA1600E

● Be careful with the shape of reverse shifting insert to

H
avoid misassembly.

PCIB0608E
K
c. Press in 1st-2nd synchronizer hub assembly, 2nd inner baulk
ring, 2nd synchronizer cone and 2nd outer baulk ring, 2nd main
gear and 2nd needle bearing using Tool. L
CAUTION:
● Apply gear oil to 2nd needle bearing, 2nd inner baulk
ring, 2nd synchronizer cone and 2nd outer baulk ring, M
1st-2nd synchronizer hub spline of mainshaft.
● Replace 2nd inner baulk ring, 2nd synchronizer cone and
2nd outer baulk ring as a set.
● Be careful with the orientation 1st-2nd coupling sleeve.
PCIB1253E

Revision: February 2006 MT-47 2005 Xterra

 TRANSMISSION ASSEMBLY

NOTE:
1st outer baulk ring has three spaces that three gear tooth is
missing and 2nd outer baulk ring has three spaces that two gear
teeth are missing.

PCIB1252E

4. Press in 1st gear bushing using Tool.

5. Install 1st outer baulk ring, 1st synchronizer cone, 1st inner
baulk ring, 1st needle bearing and 1st main gear to mainshaft.
CAUTION:
● Apply gear oil to 1st outer baulk ring, 1st synchronizer
cone, 1st inner baulk ring and 1st needle bearing.
● Replace 1st outer baulk ring, 1st synchronizer cone and
1st inner baulk ring as a set.

PCIB1254E

NOTE:
1st outer baulk ring has three spaces that three gear tooth is
missing and 2nd outer baulk ring has three spaces that two gear
teeth are missing.

PCIB1252E

6. Press in 3rd main gear using Tool.

CAUTION:
● Do not reuse 3rd main gear.

● Be careful with the orientation 3rd main gear.

PCIB1255E

Revision: February 2006 MT-48 2005 Xterra

 TRANSMISSION ASSEMBLY

7. Install 3rd-4th main spacer to mainshaft.

8. Press in 4th main gear using Tool. A
CAUTION:
● Do not reuse 4th main gear.

● Be careful with the orientation 4th main gear. B

MT

PCIB1256E

D
9. Press in mainshaft bearing using Tool.
CAUTION:
Be careful with the orientation mainshaft bearing. E

G
PCIB1257E

10. Press in reverse main gear bushing using Tool.

H

PCIB1258E
K
11. Press in 3rd gear bushing using Tool.
12. Install 3rd-4th synchronizer hub assembly according to the fol-
lowing. L
a. Install 3rd-4th coupling sleeve to 3rd-4th synchronizer hub.
CAUTION:
● Do not reuse 3rd-4th synchronizer hub and 3rd-4th cou-
M
pling sleeve.
● Replace 3rd-4th synchronizer hub and 3rd-4th coupling
sleeve as a set.
PCIB1260E

● Be careful with the orientation 3rd-4th coupling sleeve.

PCIB1259E

Revision: February 2006 MT-49 2005 Xterra

 TRANSMISSION ASSEMBLY

b. Install spread springs and shifting inserts to 3rd-4th synchro-

nizer hub.
CAUTION:
● Do not install spread spring hook onto the same shifting
insert.

SCIA1600E

● Be careful with the shape of reverse shifting insert to

avoid misassembly.

PCIB0608E

c. Press in 3rd-4th synchronizer hub assembly, 3rd inner baulk

ring, 3rd synchronizer cone, 3rd outer baulk ring, 3rd counter
gear and 3rd needle bearing using Tool.
CAUTION:
● Apply gear oil to 3rd inner baulk ring, 3rd synchronizer
cone, 3rd outer baulk ring and 3rd needle bearing, hole
spline of 3rd-4th synchronizer hub.
● Replace 3rd inner baulk ring, 3rd synchronizer cone and
3rd outer baulk ring as a set.
● Be careful with the orientation 3rd-4th coupling sleeve.
PCIB1262E
NOTE:
4th baulk ring has three spaces that one gear tooth is missing
but 3rd baulk ring doesn't.

PCIB1261E

13. Press in 4th counter gear thrust washer, 4th gear bushing, 4th
needle bearing, 4th counter gear, 4th outer baulk ring,4th syn-
chronizer cone and 4th inner baulk ring using Tool.
CAUTION:
● Apply gear oil to 4th needle bearing, 4th outer baulk ring,
4th synchronizer cone and 4th inner baulk ring.
● Replace 4th outer baulk ring, 4th synchronizer cone and
4th inner baulk ring as a set.
● Be careful with the orientation 4th counter gear thrust
washer.
PCIB1263E

Revision: February 2006 MT-50 2005 Xterra

 TRANSMISSION ASSEMBLY

NOTE:
4th baulk ring has three spaces that one gear tooth is missing A
but 3rd baulk ring doesn't.

MT

PCIB1261E D

14. Press in counter rear bearing inner race using Tool.

CAUTION: E
Be careful with the orientation counter rear bearing inner
race.
F

PCIB1264E

H
15. Install main drive gear bearing according to the following.
a. Press in main drive gear bearing using Tool.
CAUTION: I
Be careful with the orientation main drive gear bearing.

PCIB1265E

b. Select and install a snap ring to main drive gear bearing so that L
the end play comes within the standard value. Refer to MT-69,
"Snap Rings" .
End play : 0 - 0.10 mm (0 - 0.004 in) M

CAUTION:
Do not reuse snap ring.

PCIB0484E

Revision: February 2006 MT-51 2005 Xterra

 TRANSMISSION ASSEMBLY

16. Install breather to adapter plate.

CAUTION:
● Do not reuse breather.

● Be careful with the orientation breather.

PCIB1242E

17. Install magnet to adapter plate.

CAUTION:
Be careful with the orientation magnet.

PCIB1240E

18. Install baffle plate to adapter plate, and then tighten bolt to the
specified torque. Refer to MT-21, "Case Components" .

PCIB1241E

19. Install main drive gear assembly, mainshaft assembly and counter gear assembly according to the follow-
ing.
a. Install main pilot bearing, pilot bearing spacer and 5th baulk ring
to main drive gear.
b. Install main drive gear assembly, mainshaft assembly and
counter gear assembly combined in one unit to adapter plate
using brass bar.

PCIB0151E

Revision: February 2006 MT-52 2005 Xterra

 TRANSMISSION ASSEMBLY

20. Install Tool to adapter plate, and then position in a vise.

CAUTION: A
Do not directly secure mating surface of adapter plate in a
vise.
B

MT

PCIB1266E

D
21. Install snap ring to mainshaft bearing.
CAUTION:
Do not reuse snap ring. E

G
SCIA1691E

22. Install counter rear bearing to adapter plate using Tool.

H
23. Install counter rear bearing spacer to counter gear.
CAUTION:
When installing counter rear bearing spacer, groove should I
face to the rear side.

PCIB1375E
K
24. Install bearing retainer according to the following.
a. Instal bearing retainer to adapter plate.
L
b. Apply recommended thread locking sealant to threads of bolts,
and then tighten bolts to the specified torque. Refer to MT-21,
"Case Components" .
● Use Genuine Medium Strength Thread Locking Sealant or
M
the equivalent. Refer to GI-46, "Recommended Chemical
Products and Sealants" .

PCIB1238E

25. Install reverse synchronizer hub assembly according to the following.

a. Install reverse coupling sleeve to reverse synchronizer hub.
CAUTION:
● Do not reuse reverse coupling sleeve and reverse synchronizer hub.

● Replace reuse reverse coupling sleeve and reverse synchronizer hub as a set.

Revision: February 2006 MT-53 2005 Xterra

 TRANSMISSION ASSEMBLY

● Be careful with the orientation reverse coupling sleeve.

PCIB0617E

● Be careful with the orientation reverse synchronizer hub.

PCIB1267E

b. Install spread springs to shifting inserts to reverse synchronizer

hub.
CAUTION:
● Do not install spread spring hook onto the same shifting
insert.

SCIA1600E

● Be careful with the shape of 1st-2nd, 3rd-4th and 5th-6th

shifting insert to avoid misassembly.

PCIB0608E

c. Install snap ring to reverse synchronizer hub.

CAUTION:
● Do not reuse snap ring.

● Do not align the snap ring notch with synchronizer hub

groove when assembling.

PCIB1237E

Revision: February 2006 MT-54 2005 Xterra

 TRANSMISSION ASSEMBLY

d. Press in reverse synchronizer hub assembly, reverse baulk ring,

reverse main gear and reverse main needle bearing using Tools. A
CAUTION:
Apply gear oil to reverse baulk ring and reverse main nee-
dle bearing. B

MT

G
PCIB1268E

NOTE: H
Reverse baulk ring has three spaces that two gear teeth are
missing, and each space has small ditch for identification as
shown.
I

K
PCIB0168E

26. Select and install a snap ring so that the end play comes within
L
the standard value. Refer to MT-69, "Snap Rings" .
End play : 0 - 0.10 mm (0 - 0.004 in)
CAUTION: M
Do not reuse snap ring.

PCIB0225E

Revision: February 2006 MT-55 2005 Xterra

 TRANSMISSION ASSEMBLY

27. Press in reverse counter gear using Tool.

CAUTION:
● Do not reverse counter gear.

● Be careful with the orientation counter gear.

PCIB1269E

28. Select and install a snap ring so that the end play comes within
the standard value. Refer to MT-69, "Snap Rings" .
End play : 0 - 0.10 mm (0 - 0.004 in)
CAUTION:
Do not reuse snap ring.

PCIB0226E

29. Install reverse idler shaft assembly according to the following.

a. Install reverse idler needle bearing, reverse idler gear and reverse idler thrust washer to reverse idler
shaft.
CAUTION:
Apply gear oil to reverse idler needle bearing.
b. Install reverse idler shaft assembly to adapter plate.

PCIB1326E

Shift Control Components

1. Install main drive gear assembly, mainshaft assembly, counter gear assembly and reverse idler shaft
assembly. Refer to MT-45, "Gear Components" .
2. Install striking rod assembly according to the following.
a. Install striking rod assembly to adapter plate.

PCIB1235E

Revision: February 2006 MT-56 2005 Xterra

 TRANSMISSION ASSEMBLY

b. Install stopper ring to striking rod assembly.

c. Install retaining pin onto stopper ring using suitable tool. A
CAUTION:
Do not reuse retaining pin.
B

MT

PCIB1234E

D
3. Install 5th-6th fork rod (reversal side) according to the following.
a. Install 5th-6th shift fork to 5th-6th coupling sleeve.
b. Install 5th-6th fork rod (reversal side) to 5th-6th shift fork. E
c. Install retaining pin onto 5th-6th shift fork using suitable tool.
CAUTION:
Do not reuse retaining pin. F

PCIB0412E

H
4. Install 5th-6th control lever to adapter plate, and then tighten
bolts to the specified torque. Refer to MT-25, "Shift Control Com-
ponents" .
I
CAUTION:
Install 5th-6th control lever with projection side at upward.

K
PCIB1233E

5. Install 5th-6th fork rod according to the following.

L
a. Install 5th-6th fork bracket and 5th-6th fork rod to adapter plate.
b. Install retaining pin onto 5th-6th fork bracket using suitable tool.
CAUTION: M
Do not reuse retaining pin.

PCIB0239E

Revision: February 2006 MT-57 2005 Xterra

 TRANSMISSION ASSEMBLY

6. Install check balls to adapter plate.

CAUTION:
Apply gear oil to check balls.

PCIB0148E

7. Install reverse fork rod according to the following.

a. Install reverse shift fork to reverse coupling sleeve.
b. Install reverse fork rod to reverse shift fork.
c. Install retaining pin onto reverse shift fork using suitable tool.
CAUTION:
Do not reuse retaining pin.

SCIA1447E

8. Install interlock pin and interlock plunger to adapter plate.

CAUTION:
Apply gear oil to interlock pin and interlock plunger.

PCIB0147E

9. Install 1st-2nd fork rod according to the following.

a. Install 1st-2nd shift fork to 1st-2nd coupling sleeve.
b. Install 1st-2nd fork rod to 1st-2nd shift fork.
c. Install retaining pin onto 1st-2nd shift fork using suitable tool.
CAUTION:
Do not reuse retaining pin.

PCIB0602E

Revision: February 2006 MT-58 2005 Xterra

 TRANSMISSION ASSEMBLY

10. Install interlock pin and check balls to adapter plate.

CAUTION: A
Apply gear oil to interlock pin and check balls.

MT

PCIB0146E

D
11. Install 3rd-4th fork rod (reversal side) according to the following.
a. Install 3rd-4th shift fork to 3rd-4th coupling sleeve.
b. Install 3rd-4th fork rod (reversal side) to 3rd-4th shift fork. E
c. Install retaining pin onto 3rd-4th shift fork using suitable tool.
CAUTION:
Do not reuse retaining pin. F

PCIB0601E

H
12. Install 3rd-4th fork rod according to the following.
a. Install 3rd-4th fork rod to adapter plate.
b. Install 3rd-4th fork rod bracket to 3rd-4th fork rod. I
c. Install retaining pin onto 3rd-4th fork rod bracket using suitable
tool.
CAUTION: J
Do not reuse retaining pin.

PCIB0145E

L
13. Install 3rd-4th control lever according to the following.
a. Install shifter cap to 3rd-4th control lever.
b. Install 3rd-4th control lever to adapter plate, and then tighten M
bolts to the specified torque. Refer to MT-25, "Shift Control Com-
ponents" .
CAUTION:
Be careful with the orientation 3rd-4th control lever.

PCIB1232E

14. Install check ball plug according to the following.

Revision: February 2006 MT-59 2005 Xterra

 TRANSMISSION ASSEMBLY

a. Install check balls, check ball springs to adapter plate.

CAUTION:
Apply gear oil to check ball.
b. Apply recommended sealant to threads of check ball plugs, and
tighten check ball plugs to the specified torque. Refer to MT-25,
"Shift Control Components" .
● Use Genuine Silicone RTV or the equivalent. Refer to GI-
46, "Recommended Chemical Products and Sealants" .

PCIB1231E

15. Install baffle plate to adapter plate, and then tighten bolt to the
specified torque. Refer to MT-21, "Case Components" .

PCIB1325E

Case Components
1. Install main drive gear assembly, mainshaft assembly, counter gear assembly and reverse idler shaft
assembly. Refer to MT-45, "Gear Components" .
2. Install fork rods and shift forks. Refer to MT-56, "Shift Control Components" .
3. Install oil gutter to transmission case.

PCIB1228E

4. Install counter front bearing to transmission case.

CAUTION:
Apply multi-purpose grease to counter front bearing.

PCIB0436E

Revision: February 2006 MT-60 2005 Xterra

 TRANSMISSION ASSEMBLY

5. Apply recommended sealant to mating surface of transmission

case as shown. A
● Use Genuine Silicone RTV or the equivalent. Refer to GI-
46, "Recommended Chemical Products and Sealants" .
CAUTION: B
Remove old sealant adhering to the mating surfaces. Also
remove any moisture, oil, or foreign material adhering to
both mating surfaces.
MT

PCIB1270E

D
6. Install transmission case to adapter plate assembly.

G
PCIB1227E

7. Install snap ring to main drive gear bearing using suitable tool.
H
CAUTION:
Do not reuse snap ring.
I

SCIA1532E
K
8. Tighten baffle plate nut to the specified torque. Refer to MT-21,
"Case Components" .
L

SCIA1443E

9. Tighten baffle plate bolt to the specified torque. Refer to MT-21,

"Case Components" .

PCIB1271E

Revision: February 2006 MT-61 2005 Xterra

 TRANSMISSION ASSEMBLY

10. Install front cover oil seal to front cover using Tool.
Dimension A: 8.55 - 9.55 (0.336 - 0.376 in)
CAUTION:
● Do not reuse front cover oil seal.
● Apply multi-purpose grease onto oil seal lip.

● When installing, do not incline front cover oil seal.

PCIB1272E

11. Install front cover according to the following.

a. Install front cover gasket and front cover to transmission case.
CAUTION:
Do not reuse front cover gasket.
b. Temporarily tighten 2 bolts in the positions shown.
c. Temporarily tighten remaining 9 bolts.

PCIB1273E

d. Tighten bolts to the specified torque in order as shown. Refer to

MT-21, "Case Components" .
CAUTION:
Do not reuse bolts indicated as A in the figure.

PCIB1274E

Revision: February 2006 MT-62 2005 Xterra

 TRANSMISSION ASSEMBLY

12. Install washer to withdrawal lever ball pin, and then install it to
front cover. Tighten withdrawal lever ball pin to the specified A
torque. Refer to MT-21, "Case Components" .

MT

PCIB1224E

D
13. Install counter end bearing to rear extension (or OD gear case)
using suitable tool [32 mm (1.26 in) dia.].
Dimension A: 0.5 - 1.5 (0.020 - 0.059 in) E
CAUTION:
● Do not reuse counter end bearing.

● Apply gear oil to counter end bearing. F

● Install counter end bearing with maker stamp at upper
side.
G

PCIB1275E
K
14. Install rear extension oil gutter according to the following. (For 2WD models)
a. Install cap to rear extension oil gutter.
b. Install rear extension oil gutter to rear extension, and then L
tighten bolt to specified torque. Refer to MT-21, "Case Compo-
nents" .
M

PCIB1221E

Revision: February 2006 MT-63 2005 Xterra

 TRANSMISSION ASSEMBLY

15. Install rear oil seal to rear extension (or OD gear case) using
Tool.
Dimension A
2WD models : 1.2 - 2.2 mm (0.047 - 0.087 in)
4WD models : -0.5 - 0.5 mm (-0.020 - 0.020 in)
CAUTION:
● Do not reuse rear oil seal.
● Apply multi-purpose grease onto oil seal lip.

● When installing, do not incline rear oil seal.

PCIB1276E

16. Install dust seal to rear extension using Tool. (For 2WD models)
Dimension A: 0.5 - 1.5 mm (0.020 - 0.059 in)
CAUTION:
● Do not reuse dust seal.
● Apply multi-purpose grease onto dust seal lip.

● When installing, do not incline dust seal.

PCIB1277E

17. Apply recommended sealant to mating surface of rear extension

as shown.
● Use Genuine Silicone RTV or the equivalent. Refer to GI-
46, "Recommended Chemical Products and Sealants" .
CAUTION:
Remove old sealant adhering to the mating surfaces. Also
remove any moisture, oil, or foreign material adhering to
both mating surfaces.

PCIB1278E

Revision: February 2006 MT-64 2005 Xterra

 TRANSMISSION ASSEMBLY

18. Install rear extension (or OD gear case) to adapter plate, and
then tighten bolts to the specified torque in order as shown. A
Refer to MT-21, "Case Components" .

MT

PCIB1279E

D
19. Install check shift pin and pivot bolt to transmission case, and
then tighten them to the specified torque. Refer to MT-21, "Case
Components" .
E
CAUTION:
Do not reuse check shift pin and pivot bolt.
F

G
PCIB1226E

20. Install return spring plunger, return spring and return spring plug
H
to rear extension (or OD gear case), and then tighten return
spring plug to the specified torque. Refer to MT-25, "Shift Con-
trol Components" .
CAUTION: I
● Do not reuse return spring plug.

● Apply gear oil to return spring plunger.

J

PCIB1643E
K
21. Install PNP switch and back-up lamp switch according to the following.
a. Install plunger to rear extension (or OD gear case).
L
b. Apply recommended sealant to threads of PNP switch and
back-up lamp switch.
● Use Genuine Silicone RTV or the equivalent. Refer to GI-
46, "Recommended Chemical Products and Sealants" . M
c. Install PNP switch and back-up lamp switch to rear extension (or
OD gear case), and tighten them to the specified torque. Refer
to MT-21, "Case Components" .

PCIB1215E

Revision: February 2006 MT-65 2005 Xterra

 TRANSMISSION ASSEMBLY

22. Install clips to PNP switch and back-up lamp switch.

PCIB1280E

23. Install striking arm according to the following.

a. Install striking arm to striking rod assembly.
b. Install retaining pin to striking arm using suitable tool.
CAUTION:
Do not reuse retaining pin.

PCIB1219E

24. Install control housing according to the following.

a. Install gasket and control housing to rear extension (or OD gear
case).
CAUTION:
Do not reuse gasket.
b. Tighten bolts to the specified torque in order as shown. Refer to
MT-21, "Case Components" .

PCIB1216E

25. Install gasket to drain plug, and then install it to transmission

case. Tighten drain plug to the specified torque. Refer to MT-21,
"Case Components" .
CAUTION:
Do not reuse gasket.

PCIB1214E

Revision: February 2006 MT-66 2005 Xterra

 TRANSMISSION ASSEMBLY

26. Install gasket to filler plug, and then install it to transmission

case. Tighten filler plug to the specified torque. Refer to MT-21, A
"Case Components" .
CAUTION:
● Do not reuse gasket. B
● After oil is filled, tighten filler plug to specified torque.

MT

PCIB1229E

Revision: February 2006 MT-67 2005 Xterra

 SERVICE DATA AND SPECIFICATIONS (SDS)

SERVICE DATA AND SPECIFICATIONS (SDS) PFP:00030

General Specifications ECS00DZ2

Engine VQ40DE
Transmission model FS6R31A
Axle type 2WD 4WD
Number of speed 6
Synchromesh type Warner

Shift pattern

SCIA0955E

1st 4.368
2nd 2.518
3rd 1.743
Gear ratio
4th 1.283
5th 1.000
6th 0.769
Reverse 3.966
Drive 24
1st 37
2nd 32
Main gear
(Number of teeth) 3rd 32
4th 29
6th 25
Reverse 42
Drive 34
1st 12
2nd 18
Counter gear
(Number of teeth) 3rd 26
4th 32
6th 46
Reverse 15
Reverse idler gear (Number of teeth) 26
Oil capacity (Approx.) (US qt, Imp qt) 3.98 (4-1/4, 3-1/2) 4.18 (4-3/8, 3-5/8)
Reverse synchronizer Installed
Remarks Double cone synchronizer 1st, 3rd and 4th
Triple cone synchronizer 2nd

Revision: February 2006 MT-68 2005 Xterra

 SERVICE DATA AND SPECIFICATIONS (SDS)

Gear End Play ECS00DZ3

Unit: mm (in) A
Item Standard value
Counter gear 0 - 0.10 (0 - 0.004)
B
Main drive gear 0 - 0.10 (0 - 0.004)
Mainshaft (Front side) 0 - 0.10 (0 - 0.004)
Mainshaft (Rear side) 0 - 0.10 (0 - 0.004) MT

Snap Rings ECS00DZ4

Unit: mm (in)
D
Selective parts Thickness Part number*
1.89 (0.0744) 32204 01G60
1.95 (0.0768) 32204 01G61
E
1.99 (0.0783) 32204 01G62
Main drive gear
2.03 (0.0799) 32204 01G63
2.07 (0.0815) 32204 01G64
2.11 (0.0831) 32204 01G65 F
1.96 (0.0772) 32236 CD000
2.02 (0.0795) 32236 CD001
2.08 (0.0819) 32236 CD002
2.14 (0.0843) 32236 CD003
G
2.20 (0.0866) 32236 CD004
2.26 (0.0890) 32236 CD005
Counter gear
2.32 (0.0913) 32236 CD006 H
2.38 (0.0937) 32236 CD007
2.44 (0.0961) 32236 CD008
2.50 (0.0984) 32236 CD009
2.56 (0.1008) 32236 CD010 I
2.62 (0.1031) 32236 CD011
2.08 (0.0819) 32204 CD000
2.14 (0.0843) 32204 CD001
Front side J
2.20 (0.0866) 32204 CD002
2.26 (0.0890) 32204 CD003
2.08 (0.0819) 32204 CD000
2.14 (0.0843) 32204 CD001 K
2.20 (0.0866) 32204 CD002
2.26 (0.0890) 32204 CD003
2.32 (0.0913) 32204 CD004
L
Mainshaft 2.38 (0.0937) 32204 CD005
2.44 (0.0961) 32204 CD006
2.50 (0.0984) 32204 CD007
Rear side
2.56 (0.1008) 32204 CD008 M
2.62 (0.1031) 32204 CD009
2.68 (0.1055) 32204 CD010
2.74 (0.1079) 32204 CD011
2.80 (0.1102) 32204 CD012
2.86 (0.1126) 32204 CD013
2.92 (0.1150) 32204 CD014
2.98 (0.1173) 32204 CD015

*: Always check with the Parts Department for the latest parts information.

Revision: February 2006 MT-69 2005 Xterra

 SERVICE DATA AND SPECIFICATIONS (SDS)

Baulk Ring Clearance ECS00DZ5

Unit: mm (in)
Measurement point Standard value Limit value
1st, 3rd and 4th Clearance between synchronizer 0.5 - 0.7 (0.020 - 0.028) 0.3 (0.012)
(Double-cone synchronizer) cone and inner baulk ring end face
“A”
Clearance between outer baulk ring 1st : 1.0 - 1.5 (0.039 - 0.059) 0.7 (0.028)
pawl and synchronizer cone “B” 3rd, 4th : 0.85 - 1.35 (0.0335 - 0.0531) 0.7 (0.028)

PCIB0249E

2nd Clearance between synchronizer 0.6 - 1.3 (0.024 - 0.051) 0.3 (0.012)
(Triple-cone synchronizer) and clutch gear end face “A”
Clearance between outer baulk ring 0.85 - 1.35 (0.0335 - 0.0531) 0.7 (0.028)
pawl and synchronizer cone “B”
Clearance between inner baulk ring 0.7 - 1.25 (0.028 - 0.0492) 0.3 (0.012)
and clutch gear end face “C”

PCIB0835J

5th and 6th 0.7 - 1.35 (0.028 - 0.0531) 0.5 (0.020)

Reverse 0.75 - 1.2 (0.0295 - 0.047) 0.5 (0.020)

Revision: February 2006 MT-70 2005 Xterra