TYPE 2800E

EXTERNALLY MOUNTED, GAS LUBRICATED,

NON-CONTACTING, DOUBLE CARTRIDGE SEAL
Technical Specification
A – Seat/Mating Ring
B – Face/Primary Ring
(inboard)
C – Spring
D – Face/Primary Ring
(outboard)
E – O-Ring
F – Drive Collar
G – Setting Ring
H – Sleeve

B
D
A
C

Spiral Groove Technology

G
F

Product Description Performance Capabilities

Type 2800E is a state-of-the-art gas lubricated, non-contacting • Temperature: -40°F to 500°F/-40°C to 260°C
double seal cartridge for use in ANSI or DIN standard bore pumps • Pressure: up to 232 psi(g)/16 bar(g)
or limited space applications. The 2800E provides zero emissions
operation, extended seal life, reduced power consumption, and • Speed: up to 5000 fpm/25 m/s
elimination of wet seal lubrication system. It uses an available Higher operating conditions are achievable.
pressurized inert gas source for positively sealing hazardous Consult John Crane.
process fluids with zero emissions to atmosphere. Non-
contacting, dry-running technology provides high performance
sealing of heat sensitive or high purity fluids.
• For maximum achievable control technology (MACT) Design Features
compliance in new or existing standard bore pumps • 0.0 fugitive emissions
• For high reliability sealing of volatile fluids in chemical and • Compact design
petrochemical processes
• Dual balance inboard seal design
• Double seal alternative for positive sealing of high
purity fluids without the potential for product • Spiral groove technology
contamination • Non-contacting design
• Simplified support system
 TYPE 2800E
EXTERNALLY MOUNTED, GAS LUBRICATED,
NON-CONTACTING, DOUBLE CARTRIDGE SEAL
Technical Specification

Type 2800E Typical Arrangement

ØD95 D95 is the minimum possible

dimension between diametrically
opposed fixing bolts. ØD28 is the
bolt slot width.

Type 2800E Dimensional Data (mm)

Seal Size Seal Size
(mm) Code D D4 D26 D28 D95 L8 L23 L30 L39
25 0250 25 41 114 12 64.7 67.8 37.5 15.5 54.5
28 0280 28 44 117 12 67.7 67.8 37.5 15.5 54.5
30 0300 30 46 119 12 69.7 67.8 37.5 15.5 54.5
33 0330 33 49 122 14 72.7 67.8 37.5 15.5 54.5
35 0350 35 51 124 14 74.7 67.8 37.5 15.5 54.5
38 0380 38 58 135 14 79.7 69.4 39.8 17.7 56.5
40 0400 40 60 137 14 81.7 69.4 39.8 17.7 56.5
43 0430 43 63 140 14 84.7 69.4 39.8 17.7 56.5
45 0450 45 65 142 14 86.7 69.4 39.8 17.7 56.5
50 0500 50 70 147 18 91.7 69.4 41.8 17.7 56.5
53 0530 53 73 150 18 94.7 69.4 41.8 17.7 56.5
55 0550 55 75 152 18 96.7 69.4 41.8 17.7 56.5
60 0600 60 85 157 18 101.7 69.4 41.8 17.7 56.5
65 0650 65 90 180 18 106.7 71.4 43.8 19.7 58.5
80 0800 80 109 195 18 121.7 71.4 43.8 19.7 58.5
100 1000 100 129 215 22 141.7 71.4 43.8 19.7 58.5
 TYPE 2800E
EXTERNALLY MOUNTED, GAS LUBRICATED,
NON-CONTACTING, DOUBLE CARTRIDGE SEAL
Technical Specification

Type 2800E Dimensional Data (inches)

Seal Size/D1 Seal Size/D
(inches) Code D4 D26 D28 D95 L8 L23 L30 L39
0.875 0222 1.500 3.750 0.437 2.295 2.574 1.398 0.531 2.028
1.000 0254 1.625 3.750 0.437 2.421 2.574 1.398 0.531 2.028
1.125 0285 1.750 4.250 0.437 2.469 2.574 1.398 0.531 2.028
1.250 0317 2.000 4.250 0.437 2.669 2.574 1.398 0.531 2.028
1.375* 0349 2.125 4.250 0.437 2.795 2.574 1.398 0.531 2.028
1.375** 0349 2.000 4.250 0.437 2.795 2.574 1.398 0.531 2.028
1.500 0381 2.250 4.875 0.562 3.142 2.732 1.567 0.697 2.224
1.625 0412 2.375 4.500 0.437 3.268 2.732 1.567 0.697 2.224
1.750 0444 2.500 5.500 0.562 3.390 2.732 1.567 0.697 2.224
1.875 0476 2.625 5.500 0.562 3.335 2.732 1.567 0.697 2.224
2.000 0508 2.750 4.750 0.562 3.461 2.732 1.567 0.697 2.224
2.125 0539 2.875 6.000 0.687 3.768 2.732 1.567 0.697 2.224
2.250 0571 3.125 6.500 0.687 3.890 2.732 1.567 0.697 2.224
2.375 0603 3.250 6.250 0.687 4.016 2.732 1.567 0.697 2.224
2.500 0635 3.375 6.500 0.687 4.142 2.812 1.724 0.776 2.303
2.625 0666 3.625 6.500 0.687 4.268 2.812 1.724 0.776 2.303
2.750 0698 3.750 7.000 0.687 4.370 2.812 1.724 0.776 2.303
3.000 0762 4.000 7.000 0.687 4.642 2.812 1.724 0.776 2.303
3.500 0889 4.500 7.250 0.812 5.142 2.812 1.724 0.776 2.303
4.000 1016 5.000 7.250 0.812 5.642 2.812 1.724 0.776 2.303
*Durco **Goulds

Pressure Limits

The basic pressure rating is based on a standard seal installed according to the criteria given in this data sheet at a minimum speed of
1450rpm, and according to generally accepted industrial practices.
Contact John Crane for process services outside this range and with more detailed application information in order to obtain the actual
dynamic pressure rating.
 TYPE 2800E
EXTERNALLY MOUNTED, GAS LUBRICATED,
NON-CONTACTING, DOUBLE CARTRIDGE SEAL
Technical Specification

Criteria for Installation

SHAFT/SLEEVE LIMITS

Surface Finish 1.6µmRa/63Ra or better

Ovality/Out of Roundness (Shaft) 0.05mm/0.002"

End Play/Axial Float Allowance +_ 0.08mm/0.003"

Runout/Out of Squareness 0.051mm/0.002"

Shaft Squareness to Housing 0.08mm/0.003"

Barrier Gas Consumption

*Curves are to be used as a guide only. Actual consumption rates may vary.
Consult John Crane if specific application gas consumption data is required.
 TYPE 2800E
EXTERNALLY MOUNTED, GAS LUBRICATED,
NON-CONTACTING, DOUBLE CARTRIDGE SEAL
Technical Specification

Barrier Gas Supply Systems

Available from John Crane in both standard tamper proof enclosure and panel mounted designs.

12
4
6
Standard Components
1 Isolating Ball Valve
2 Coalescing Filter
3 Pressure Regulator
5
4 Pressure Gauge
5 Flow Meter (Low Range)
6 Flow Meter (High Range)
7 Tubing Clamp
3
8 Check Valve
2 11 9 Coupling (To Seal Piping)
10 Back Panel

8 7 Options
11 Flow Switch
1 12 Pressure Switch
9 10
13 Enclosure
■ Isolast™ and Kalrez® for the Check Valve Seat Material

■ Stand
Barrier Seal
■ Enclosures are also available in a NEMA 4X
Supply Chamber
Enclosure (as shown)
■ Gas Amplifier/Booster Systems

■ Pressure Tracking Regulators

Further application information is available from

John Crane.
 TYPE 2800E
EXTERNALLY MOUNTED, GAS LUBRICATED,
NON-CONTACTING, DOUBLE CARTRIDGE SEAL
Technical Specification
Materials of Construction
SEAL COMPONENTS MATERIALS

Description Standard Options

Face/Primary Ring Carbon —

Seat/Mating Ring Tungsten Carbide Silicon Carbide

Cap Head Screws 316 Stainless Steel Alloy 20GB3 SS (UNS N8020)
Anti-Rotation Pins Alloy C-276 (UNS N10276)
Snap Ring Titanium
Sleeve
Gland Plate
Spring
Set Screws
Drive Collar
Drive Pins

O-Rings Fluoroelastomer Perfluoroelastomer

EPR

Setting Ring (Spacer) Pure PTFE —

Gasket PTFE Glass Filled —

TYPE 2800E
EXTERNALLY MOUNTED, GAS LUBRICATED,
NON-CONTACTING, DOUBLE CARTRIDGE SEAL
Technical Specification
 TYPE 2800E
EXTERNALLY MOUNTED, GAS LUBRICATED,
NON-CONTACTING, DOUBLE CARTRIDGE SEAL
Technical Specification

Isolast is a registered trademark of Trelleborg.

Kalrez is a registered trademark of DuPont.

North America Europe Latin America Middle East & Africa Asia Pacific
United States of America United Kingdom Brazil United Arab Emirates Singapore
Tel: 1-847-967-2400 Tel: 44-1753-224000 Tel: 55-11-3371-2500 Tel: 971-481-27800 Tel: 65-6518-1800
Fax: 1-847-967-3915 Fax: 44-1753-224224 Fax: 55-11-3371-2599 Fax: 971-488-62830 Fax: 65-6518-1803

If the products featured will be used in a potentially dangerous and/or hazardous process, your John Crane representative should be consulted prior to
their selection and use. In the interest of continuous development, John Crane Companies reserve the right to alter designs and specifications without
prior notice. It is dangerous to smoke while handling products made from PTFE. Old and new PTFE products must not be incinerated. ISO 9001 and
ISO14001 Certified, details available on request.
©2015 John Crane Revised 10/15 www.johncrane.com TD-2800E