USACE - Retaining and Flood Walls

CECW-ED Department of the Army EM 1110-2-2502
U.S. Army Corps of Engineers

Engineer Manual Washington, DC 20314-1000 29 September 1989
1110-2-2502
Engineering and Design
RETAINING AND FLOOD WALLS
Distribution Restriction Statement

Approved for public release; distribution is
unlimited.
EM 1110-2-2502
"V: 29 Sept 1989
US Army Corps
of Engineers
ENGINEERING AND DESIGN
Retaining and Flood Walls
ENGINEER MANUAL
20020628 041
DEPARTMENT OF THE ARMY EM 1110-2-2502
U. S. Army Corps of Engineers
CECW-ED Washington, D. C. 20314-1000
CECW-EG
Engineer Manual 29 September 1989

No. 1110-2-2502

1. Purpose. This manual provides guidance for the safe design and economical
construction of retaining and flood walls. This manual is intended primarily
for retaining walls which will be subjected to hydraulic loadings such as
flowing water, submergence, wave action, and spray, exposure to chemically
contaminated atmosphere, and/or severe climatic conditions. For the design of
retaining walls which will not be subjected to hydraulic loadings or severe
environmental conditions as described above, TM 5-818-1 may be used for
computing the loadings and evaluating the stability of the structure.
2. Applicability. This manual applies to all HQUSACE/OCE elements and field

operating activities having responsibilities for the design of civil works
projects.
FOR THE COMMANDER:
Albert J. Genetti, Jr.

Colonel, Corps of Engineers
Chief of Staff
This manual supersedes EM 1110-2-2501 dated January 1948 and EM 1110-2-2502

dated 29 May 1961.
DEPARTMENT OF THE ARMY EM 1110-2-2502
U. S. Army Corps of Engineers
CECW-ED Washington, D. C. 20314-1000
CECW-EG
Engineer Manual 29 September 1989

No. 1110-2-2502

Table of Contents
Subject Paragraph Page
CHAPTER 1. INTRODUCTION
Purpose 1-1 1-1

Applicability- 1-2 1-1
References and Bibliography- 1-3 1-1
Terms 1-4 1-1
Scope 1-5 1-1
CHAPTER 2. GENERAL DESIGN CONSIDERATIONS
Section I. Types of Retaining Walls

Common Types of Retaining Walls 2-1 2-1
Gravity Concrete Wall 2-2 2-1
Cantilever Reinforced Concrete Wall 2-3 2-1
Alternate Types of Retaining Walls 2-4 2-1
Section II. Types of Flood Walls
Common Types of Flood Walls 2-5 2-1
Cantilever T-Type Wall 2-6 2-4
Cantilever I-Type Wall 2-7 2-4
Other Types of Flood Walls 2-8 2-4
Section III. Differences Between Retaining and Flood Walls
Purpose of Walls 2-9 2-4
Seepage and Leakage Control Requirements 2-10 2-4
Wall Stability 2-11 2-6
Special Flood Wall Monoliths 2-12 2-6
Design Philosophy 2-13 2-6
Stability Considerations 2-14 2-6
Section IV. Coordination Between Disciplines
Engineering Team 2-15 2-6
Section V. Geotechnical Investigations
Planning the Investigation 2-16 2-7
Foundation Exploration and Site
Characterization 2-17 2-7
Testing of Foundation Materials 2-18 2-8
In Situ Testing of Foundation Materials 2-19 2-10
Backfill Materials 2-20 2-15
Design Strength Selection 2-21 2-15
EM 1110-2-2502
29 Sep 89
CHAPTER 3. FORCES ON WALLS
Section I. Introduction
General 3-1 3-1
Limit-Equilibrium Analysis 3-2 3-1
Relationship of Forces to Sliding Analysis 3-3 3-1
Section II. Earth Pressures and Forces
Cohesionless Materials 3-4 3-2
Cohesive Materials 3-5 3-5
Pressures in Soil-Water Systems 3-6 3-6
Design Earth Pressures and Forces, Driving
Side 3-7 3-6
Design Earth Pressures and Forces, Resisting
Side 3-8 3-8
Design Earth Pressures and Forces on the
Base 3-9 3-9
At-Rest Earth Pressure Equations 3-10 3-11
Strength Mobilization Factor 3-11 3-13
Earth Force Calculation, Coulomb's Equations 3-12 3-17
Earth Force Calculation, General Wedge
Method 3-13 3-23
Earth Pressure Calculations Including Wall
Friction 3-14 3-37
Distribution of Horizontal Earth Pressure 3-15 3-38
Surcharge Effects 3-16 3-45
Earth Pressures Due to Compaction 3-17 3-47
Section III. Water Pressures
Pressure Calculations 3-18 3-53
Seepage Analysis by Line-of-Creep Method 3-19 3-55
Seepage Analysis by Method of Fragments 3-20 3-55
Seepage Analysis by the Finite Element
Method 3-21 3-58
Uplift Calculations for Rock Foundations 3-22 3-58
Effect of Drains 3-23 3-59
Surge and Wave Loads 3-24 3-59
Section IV. Supplemental Forces
Wind Load 3-25 3-61
Earthquake Forces 3-26 3-61
CHAPTER 4. STRUCTURE STABILITY
Scope 4-1 4-1

Section I. Loading Conditions
Representative Loading Conditions 4-2 4-1
Retaining Walls 4-3 4-1
Inland Flood Walls 4-4 4-1
Coastal Flood Walls 4-5 4-2
Section II. Stability Considerations
General Requirements 4-6 4-3
Stability Criteria 4-7 4-3
EM 1110- 2-2502
29 Sep 89
Subject Paraqraph Paqe
Section III. Overturning Stability-

Resultant Location 4-8 4-3
Overturning Stability Criteria 4-9 4-15
Section IV. Structure Sliding Stability
Overview of Sliding Stability Analysis 4-10 4-15
Sliding Factor of Safety 4-11 4-17
Assumptions and Simplifications 4-12 4-18
General Wedge Equation 4-13 4-20
Slip-Plane Angle 4-14 4-23
Single Wedge Analysis 4-15 4-24
Multiple Wedge Analysis 4-16 4-25
Sliding Stability Criteria 4-17 4-27
Design Considerations 4-18 4-27
Section V. Bearing Capacity Analysis
General Computations 4-19 4-28
Inadequate Bearing Capacity 4-20 4-28
Bearing Capacity Criteria 4-21 4-28
Section VI. Summary of Design Procedures
Design Procedures 4-22 4-28
CHAPTER 5. FOUNDATION ANALYSES
Section I. Bearing Capacity of Wall Foundations

Analysis Principles and Methods 5-1 5-1
General Bearing Capacity Equation 5-2 5-1
Bearing Capacity Factors 5-3 5-2
Embedment Factors 5-4 5-4
Inclination Factors 5-5 5-4
Base Tilt Factors 5-6 5-7
Ground Slope Factors 5-7 5-7
Effective Overburden Pressure 5-8 5-7
Combination of Factors 5-9 5-8
Example 5-10 5-8
Section II. Other Considerations
Settlement 5-11 5-8
Deep-Seated Sliding 5-12 5-8
Liquefaction Susceptibility 5-13 5-11
CHAPTER 6. DESIGN AND CONSTRUCTION DETAILS AND CAUSES

OF UNSATISFACTORY PERFORMANCE
Foundation Preparation 6-1 6-1

Concrete Mixture Proportions 6-2 6-1
Constructability 6-3 6-1
Joints 6-4 6-1
Soil Backfill 6-5 6-3
Drainage 6-6 6-4
Causes of Unsatisfactory Performance 6-7 6-15
111
EM 1110-2-2502
29 Sep 89
CHAPTER 7. SPECIAL CONSIDERATIONS FOR FLOOD WALLS
Section I. General Characteristics

Introduction 7-1 7-1
Rationale for Loading Cases 7-2 7-1
Section II. Seepage Control
General Considerations 7-3 7-3
Underseepage Control 7-4 7-3
Section III. Foundation Considerations
Base Types 7-5 7-10
Horizontal Water and Earth Loads on Keys 7-6 7-10
Unsuitable Foundation Material and Bank
Stability 7-7 7-10
Scour Protection 7-8 7-13
Section IV. Types of Monoliths
Change-of-Alignment Monoliths 7-9 7-13
Closure and Abutment Monoliths 7-10 7-13
Drainage Structure Monoliths 7-11 7-13
Transition Sections Between Flood Walls and
Levees 7-12 7-13
Section V. Water Stops and Joints
Water Stops 7-13 7-17
Contraction and Expansion Joints 7-14 7-17
Section VI. Site Considerations
Adjacent Structures and Rights-of-Way 7-15 7-21
Architectural and Landscaping Considerations 7-16 7-22
Section VII. Instrumentation
General and Specific Considerations 7-17 7-22
Types of Instrumentation 7-18 7-23
Section VIII. Operation and Maintenance Manual Requirements
General Coverage 7-19 7-24
Section IX. Review of Existing Flood Walls
Inspection 7-20 7-24
Repair Measures 7-21 7-26
CHAPTER 8. CONCRETE GRAVITY WALLS
General Factors 8-1 8-1

Foundation Investigation 8-2 8-1
Materials 8-3 8-1
Design 8-4 8-1
CHAPTER 9. CANTILEVER REINFORCED CONCRETE WALLS
General Characteristics 9-1 9-1

Foundation Investigation 9-2 9-1
Materials 9-3 9-1
Reinforcement Cover 9-4 9-1
EM 1110- 2-2502
29 Sep 89
Subject Paraqraph Paqe
Load Cases 9-5 9-1

Structural Stability 9-6 9-1
Structural Design 9-7 9-1
Reinforced Concrete Design 9-8 9-3
Foundation Analyses 9-9 9-11
CHAPTER 10. ALTERNATE TYPES OF RETAINING WALLS
Classes of Retaining Walls 10-1 10-1
Alternate Types of Retaining Walls 10-2 10-1
Section II. Mechanically Stabilized Backfill Systems
General Background 10-3 10-1
Available Systems 10-4 10-1
Advantages and Disadvantages 10-5 10-2
Cost Considerations 10-6 10-7
Mechanisms and Behavior 10-7 10-7
Materials 10-8 10-9
Construction Considerations 10-10 10-12
Instrumentation and Monitoring 10-11 10-13
Maintenance and Repair 10-12 10-13
Section III. Precast Concrete Modular Systems
Background 10-13 10-14
Basic Components 10-14 10-14
Advantages and Disadvantages 10-15 10-14
Construction Considerations 10-17 10-19
Instrumentation and Monitoring 10-18 10-20
Maintenance and Repair 10-19 10-20
APPENDIX A. REFERENCES A-l
APPENDIX B. BIBLIOGRAPHY B-l
APPENDIX C. NOTATION FOR CHAPTERS 3, 4, and 5 C-l
APPENDIX D. NOTATION FOR CHAPTER 9 D-l
APPENDIX E. COMPARISON OF DANISH CODE AND JAKY EQUATIONS

FOR AT-REST COEFFICIENT WITH COULOMB
COEFFICIENT FOUND USING REDUCED SHEAR
STRENGTH PARAMETER &„
T E-l
d
APPENDIX F. DERIVATION OF GENERAL WEDGE EQUATION FOR
SINGLE WEDGE ANALYSIS (EQUATION 3-23) F-l
v
EM 1110-2-2502
29 Sep 89
APPENDIX G. DERIVATION OF EQUATIONS FOR CRITICAL SLIP-

PLANE ANGLE (a) FOR DRIVING AND
RESISTING WEDGES G-l
APPENDIX H. DERIVATION OF PRESSURE COEFFICIENTS FOR

SOLUTION OF LATERAL EARTH PRESSURE
PROBLEMS H-l
APPENDIX I. DERIVATION OF EQUATION FOR DEPTH OF CRACK

d IN COHESIVE SOIL 1-1
C
APPENDIX J. LATERAL PRESSURES DUE TO COMPACTION J-l
APPENDIX K. DERIVATION OF VERTICAL SHEAR FORCE FOR

UPWARD SLOPING BACKFILL K-l
APPENDIX L. DERIVATION OF GENERAL WEDGE EQUATION FOR

MULTIPLE WEDGE ANALYSIS L-l
APPENDIX M. LATERAL EARTH PRESSURE COMPUTATIONS,

EXAMPLES M-l
APPENDIX N. STABILITY, BEARING CAPACITY, AND

REINFORCEMENT COMPUTATIONS, EXAMPLES N-l
APPENDIX 0. COMPUTER PROGRAM ABSTRACTS FOR REFERENCED

PROGRAMS 0-1
GLOSSARY Glossary 1
Sli^^^^W^ST'';'
EM 1110-2-2502
29 Sep 89
LIST OF FIGURES
Figure Page
2-1 Types of retaining walls 2-2

2-2 Types of flood walls 2-3
2-3 Less commonly used flood wall types 2-5
2-4 Drained friction angle versus plasticity index 2-9
2-5 SPT correction to 1 tsf (2 ksf) 2-13
2-6 <)>' versus N' for granular materials 2-13
2-7 q /N versus D „ 2-14
c 50
2-8 Soil classification from cone penetrometer 2-14
2-9 Friction angle of granular backfills 2-16
3-1 Development of earth pressures for a cohesionless
material 3-3
3-2 Relationship of earth pressures to wall movements 3-4
3-3 Vertical and horizontal pressures in a cohesion-
less soil mass 3-7
3-4 Forces on base of wall 3-10
3-5 Base pressures 3-12
3-6 At-rest earth pressure coefficients 3-14
3-7 Application of the strength mobilization factor 3-15
3-8 Mohr-Coulomb failure criterion 3-16
3-9 Comparison of active earth pressures 3-20
3-10 Variables used in Coulomb equation 3-21
3-11 Comparison of passive earth pressures 3-24
3-12 Wedge method on driving side 3-27
3-13 Force polygon for wedge method on driving side 3-28
3-14 Wedge analysis for irregular backfill 3-30
3-15 Surcharge effect on critical slip plane 3-32
3-16 Wedge analysis in layered soil 3-33
3-17 Wedge method for resisting-side wedge 3-36
3-18 Passive earth pressure coefficients 3-38
3-19 Lateral pressures, one soil completely above water
table or completely below water table 3-40
3-20 Lateral pressures, one soil, water, finite surcharge 3-41
3-21 Lateral pressures, three soils, water 3-43
3-22 Pressure distribution due to irregular backfill 3-44
3-23 Lateral pressure distribution; active case, soil
with cohesion 3-46
3-24 Lateral pressure distribution; passive case, soil
with cohesion 3-47
3-25 Increase in pressure due to point load 3-48
3-26 Increase in pressure due to line load 3-49
3-27 Increase in pressure due to strip load 3-50
3-28 Resultant forces, point and line loads 3-51
3-29 Approximate line of action for line loads 3-52
3-30 Design pressure envelope for nonyielding walls
with compaction effects 3-54
EM 1110-2-2502
29 Sep 89
LIST OF FIGURES (Continued)
Figure Page
3-31 Water pressures from flow net 3-56

3-32 Water pressure by line-of-creep method 3-57
3-33 Seepage path for line of creep 3-58
3-34 Driving and resisting seismic wedges, no saturation 3-63
3-35 Influence of k and ß on magnification factor 3-66
3-36 Seismic wedges, water table within wedge 3-70
3-37 Static and dynamic pressure diagrams, water table
within wedge 3-71
3-38 Static and dynamic pressure diagrams, cohesive fill,
water table within wedge 3-75
3-39 Hydrodynamic forces for freestanding water 3-78
4-1 Stability considerations for retaining and flood walls 4-4
4-2 Forces for overturning analysis for wall with
horizontal base 4-8
4-3 Forces for overturning analysis for wall with a
sloping base 4-9
4-4 Relationship between base width in compression and
resultant location 4-11
horizontal base and key 4-12
sloping base and key 4-13
4-7 Shear force for upward sloping backfill 4-14
4-8 Typical soil/structure system with an assumed
failure surface 4-16
4-9 Free-body diagram of i wedge 4-19
4-10 Geometry of typical i wedge and adjacent wedges 4-21
4-11 Single wedge analysis of sliding stability 4-26
4-12 Wall design flowchart 4-29
5-1 Terms used in bearing capacity equation 5-3
5-2 Deep-seated sliding analysis with vertical face of
driving wedge at heel 5-9
5-3 Deep-seated sliding analysis with vertical face of
driving wedge at toe 5-10
5-4 Shallow shear surface 5-11
6-1 Inclined drainage blanket 6-4
6-2 Effect of drain location on excess hydrostatic pressures
on the failure plane 6-6
6-3 Drainage blanket located adjacent to retaining wall 6-7
6-4 Prefabricated drainage composite used as drain
adjacent to retaining wall 6-8
6-5 Drainage system to prevent frost penetration
behind retaining wall 6-8
6-6 Drainage system to use with clay backfill 6-9
6-7 Inspection hole for longitudinal drain 6-10
EM 1110-2-2502
29 Sep 89
LIST OF FIGURES (Continued)
Figure Page
6-8 Vertical check valve at end of longitudinal drain 6-11

6-9 Approximation for estimating reduction in permeability
of narrow size-ranged aggregate caused by turbulent
flow 6-14
6-10 Summary of experience with unsatisfactory retaining
walls 6-16
7-1 Flow around interior embedded water stop in the base 7-4
7-2 T-type flood wall--horizontal base 7-5
7-3 Uplift pressures for a wall with a sheet pile cutoff 7-7
7-4 T-type flood wall--sloped base 7-11
7-5 Removal limits of unsuitable foundation material 7-12
7-6 Return keys on reentrant monolith 7-14
7-7 Flood wall-levee transitions 7-15
7-8 Typical detail of joint between I-wall and T-wall 7-16
7-9 Typical joint and water stop details 7-18
7-10 Emergency measures to control piping 7-27
7-11 Permanent water stop repair measures 7-28
9-1 Shear force for upward-sloping backfill 9-2
9-2 Rectangular beam, simple bending with no
compression reinforcement 9-7
9-3 Rectangular member, bending with small axial
compression load, no compression reinforcement 9-8
9-4 Rectangular member, bending with axial tensile load,
where M /P > (d - h/2) 9-9
u u
9-5 Rectangular member, bending with axial tensile load,
where M /P < (d - h/2) 9-10
u u
10-1 Schematic diagram of reinforced earth retaining wall 10-3
10-2 Schematic diagram of reinforced soil embankment
retaining wall 10-4
10-3 VSL retained earth retaining wall 10-5
10-4 Tensar geogrid retaining wall 10-6
10-5 Schematic diagram of Doublewal retaining wall 10-15
10-6 Materials used to construct Doublewal retaining wall 10-16
10-7 Schematic diagram of Criblock retaining wall 10-17
10-8 Schematic diagram of Evergreen retaining wall 10-18
SSS!
EM 1110-2-2502
29 Sep 89
CHAPTER 1
INTRODUCTION
1-1. Purpose.
a. General. This manual provides guidance for the safe design and eco-
nomical construction of retaining and flood walls. This manual is intended
primarily for retaining walls which will be subjected to hydraulic loadings
such as flowing water, submergence, wave action, and spray, exposure to chemi-
cally contaminated atmosphere, and/or severe climatic conditions. For the de-
sign of retaining walls which will not be subjected to hydraulic loadings or
severe environmental conditions as described above, TM 5-818-1 may be used for
computing the loadings and evaluating the stability of the structure.
b. Variations from Guidance. For the evaluation of existing retaining

and flood walls which have been loaded up to or above the design loads and
show no displacement problems or any other sign of weakening, consideration
can be given to reducing the conservatism of the criteria contained in this
manual. If variations from the guidance are necessary, justification for the
variations should be submitted to HQUSACE to the attention of CECW-E for
approval.
1-2. Applicability. This manual applies to all HQUSACE/OCE elements and to

all field operating activities having responsibilities for the design of civil
works projects.
1-3. References and Bibliography. References and computer program user

guides cited in this manual are listed in Appendix A. Additional reference
materials pertaining to the subject matter addressed in this manual are
included in Appendix B, "Bibliography." Computer program abstract
descriptions are shown in Appendix O.
1-4. Terms. Special terms used in this manual are explained in the glossary.
1-5. Scope.
a. Types of Walls. This manual presents design guidance for retaining

walls and inland and coastal flood walls. Retaining walls are defined as any
wall that restrains material to maintain a difference in elevation. A flood
wall is defined as any wall having as its principal function the prevention of
flooding of adjacent land. Not specifically covered in this manual are sea-
walls which are defined as structures separating land and water areas, primar-
ily designed to prevent erosion and other damage due to wave action. They are
frequently built at the edge of the water, but can be built inland to with-
stand periods of high water. Seawalls are generally characterized by a mas-
sive cross section and a seaward face shaped to dissipate wave energy.
Coastal flood walls, however, are generally located landward of the normal
high water line so that they are inundated only by hurricane or other surge
tide and have the smooth-faced cantilever stems shown in this manual.
1-1
EM 1110-2-2502
29 Sep 89
b. Types of Foundations. This manual describes procedures for the design

of retaining and flood walls on shallow foundations, i.e., bearing directly on
rock or soil. The substructure design of pile-founded walls is not included,
but is covered in EM 1110-2-2906.
c. Flood Wall Guidance. A flood wall is treated as a special case of a

retaining wall. Unless specifically noted, the guidance herein applies to
both retaining and flood walls.
d. Geotechnical and Structural Aspects. Both geotechnical and structural

aspects of wall design are included. Coordination between geotechnical
engineers, structural engineers, and geologists in the design of retaining and
flood walls is essential.
1-2
EM 1110-2-2502
29 Sep 89
CHAPTER 2
GENERAL DESIGN CONSIDERATIONS
Section I. Types of Retaining Walls
2-1. Common Types of Retaining Walls. The most common types of retaining
walls are gravity concrete, cantilever T-type reinforced concrete, and canti-
lever and anchored sheet pile walls. Gravity and cantilever reinforced con-
crete walls are covered in this manual and illustrated in Figure 2-1. Alter-
nate types of retaining walls, including mechanically stabilized backfill and
precast modular gravity walls, are covered in Chapter 10. An example of one
type of alternate retaining wall is shown in Figure 2-1. Counterfort and
buttressed reinforced concrete walls are less commonly used and are not spe-
cifically discussed in this manual. Much of the conceptual information and
the information in Chapters 3 and 9 is applicable to all types of walls.
2-2. Gravity Concrete Wall. A gravity wall (Figure 2-1) consists of mass
concrete, generally without reinforcement. It is proportioned so that the
resultant of the forces acting on any internal plane through the wall falls
within, or close to, the kern of the section. A small tensile stress capacity
is permissible for localized stresses due to extreme and temporary loading
conditions.
2-3. Cantilever Reinforced Concrete Wall. A cantilever T-type reinforced

concrete wall (Figure 2-1) consists of a concrete stem and base slab which
form an inverted T. The structural members are fully reinforced to resist
applied moments and shears. The base is made as narrow as practicable, but
must be wide enough to ensure that the wall does not slide, overturn, settle
excessively, or exceed the bearing capacity of the foundation. The bottom of
the base should be below the zone subject to freezing and thawing or other
seasonal volume changes. The T-type wall is usually the most economical type
of conventional wall and is more widely used than any other type for common
retaining wall heights.
2-4. Alternate Types of Retaining Walls. Retaining walls using mechanically

stabilized backfill (Figure 2-1) and precast modular gravity walls can be sub-
stantially more economical to construct than conventional walls (Leary and
Klinedinst 1984). However, a short life, serious consequences of failure, or
high repair or replacement costs could offset a lower first cost. In addi-
tion, the design engineer must assure the overall adequacy of the design since
the manufacturer of the wall may provide only that part of the design above
the foundation. Chapter 10 covers mechanically stabilized backfill systems
and precast modular gravity walls.
Section II. Types of Flood Walls
2-5. Common Types of Flood Walls. The most common types of flood walls are
cantilever T-type and cantilever I-type walls. Examples of these walls are
shown in Figure 2-2.
2-1
EM 1110-2-2502
29 Sep 89
i i_i_».
GRAVITY REINFORCED CONCRETE CANTILEVER
COPING
ANCHORING
ELEMENTS
FACING
PANEL
GRANULAR
LEVELING PAD BACKFILL
MECHANICALLY STABILIZED BACKFILL
Figure 2-1. Types of retaining walls
2-2
EM 1110-2-2502
29 Sep 89
HORIZONTAL BASE KEYED

HORIZONTAL BASE SLOPED BASE INTO STRONGER SOIL
NOTE: R.S.= RIVER SIDE <OR SEAWARD, UNPROTECTED SIDE)
L.S.= LAND SIDE (OR PROTECTED SIDE)
INVERTED T-TYPE CANTILEVER WALLS
-t1* T ^
#
CANTILEVER I-TYPE SHEET PILE WALLS
SHEAR CONNECTORS
BEARING PILES
PRESTRESSED CONCRETE SHEET

PILES WITH WATERTIGHT
JOINTS
BRACED SHEET PILE COASTAL FLOOD WALL
* Analysts of this type of wall Is beyond
the scope of this manual.
Figure 2-2. Types of flood walls
2-3
EM 1110-2-2502
29 Sep 89
2-6. Cantilever T-Type Wall. Most flood walls are of the inverted T-type
(Figure 2-2). These walls are discussed in detail in Chapter 7. The cross
bar of the T serves as a base and the stem serves as the water barrier. When
founded on earth, a vertical base key is sometimes used to increase resistance
to horizontal movement. If the wall is founded on rock, a key is usually not
provided. Where required, the wall can be supported on piles. A sheet pile
cutoff can be included to control underseepage or provide scour protection for
the foundation. T-type walls may be provided with a horizontal or sloped
base. The advantages of sloped and horizontal bases are discussed in
paragraph 7-5.
2-7. Cantilever I-Type Wall. I-type flood walls consist of driven sheet
piles capped by a concrete wall (Figure 2-2) . I-walls are most often used in
connection with levee and T-wall junctions or for protection in narrow re-
stricted areas where the wall height is not over 8 to 10 feet, depending on
soil properties and geometry. The design of these types of walls is beyond
2-8. Other Types of Flood Walls.
a. Braced Sheet Pile Flood Wall. This wall consists of a row of vertical
prestressed concrete sheet piles, backed by batter piles connected to the
sheet piles by a cast-in-place horizontal concrete beam with shear connectors
as required to resist the vertical component of load in the batter pile (Fig-
ure 2-2). This type of wall has been used for coastal flood walls. It is
ideal for wet areas because no excavation or dewatering is required to con-
struct the wall. The disadvantage is that it is more indeterminate than other
wall types. The design of this wall is beyond the scope of this manual.
b. Less Commonly Used Types. There are various other types of walls that
may be used for flood walls such as: buttress, counterfort, gravity,
cellular, and cellular sheet pile, some of which are shown in Figure 2-3.
These walls, except for the gravity wall, are beyond the scope of this manual.
Section III. Differences Between Retaining and Flood Walls
2-9. Purpose of Walls. A retaining wall is any wall that retains material to
maintain a change in elevation whereas the principal function of a flood wall
is to prevent flooding (inundation) of adjacent land. A floodwall is subject
to water force on one side which is usually greater than any resisting earth
force on the opposite side. A wall may be a retaining wall for one loading
condition and a flood wall for another loading condition. The flood loading
(surge tide, river flood, etc.) may be from the same or the opposite direction
as the higher earth elevation.
2-10. Seepage and Leakage Control Requirements. All water-retaining struc-

tures may be subject to seepage through, under, and around them. Inadequate
control of seepage may affect the stability of a flood wall regarding uplift
or loss of support resulting from erosion. Properly controlled seepage, even
if quantities of flow remain large, presents little or no hazard. Control of
2-4
EM 1110-2-2502
2 9 Sep 89
CELL
ARC
CELLULAR SHEET PILE
SHEET
PILE
SHEET SHEET
PILE PILE
BUTTRESS*
CELLULAR
GRAVITY
NOTES: W.S.= WATER SIDE (OR SEAWARD, UNPROTECTED SIDE)
L.S.= LAND SIDE (OR PROTECTED SIDE)
* Analysts of this type wall !s beyond

Figure 2-3. Less commonly used flood wall types
2-5
EM 1110-2-2502
29 Sep 89
through-seepage is provided by water stops. Retaining walls rarely need seep-

age protection other than to relieve the hydrostatic load on the fill side of
the wall. Water stops are used in retaining walls to prevent water passage
from the backfill through the vertical joints. Seepage control and water
stops are more fully discussed in paragraphs 3-23, 6-4e, 6-6, 7-4, and 7-13.
2-11. Wall Stability. Generally, it is more difficult to design stable flood

walls than retaining walls. By their very nature, flood walls are usually
built in a flood plain which may have poor foundation conditions. Uplift is
always a critical item with flood walls but seldom a problem with retaining
walls since the loads acting on a retaining wall are usually soil backfills.
The water load on a flood wall can be more severe, especially when wave load-
ings are applicable. When the ground-water surface is near or above the wall
footing, a common occurrence with flood walls, the allowable bearing capacity
of the soil is reduced. The reduction of stability, due to the erosion of the
earth cover over and beyond the base, must be considered.
2-12. Special Flood Wall Monoliths. Careful attention must be given to wall
monoliths that have loading, support, or other conditions that vary along the
length of the monolith. These monoliths, which may include closure structures,
pipeline crossings, corner structures, etc., must be analyzed as complete
three-dimensional entities instead of the usual two-dimensional unit slices.
2-13. Design Philosophy. Retaining walls are normally built as an appurte-

nance to other structures: dams, hydroelectric power houses, pump stations,
etc. The consequences of failure of a retaining wall are often lower than for
flood walls. Also, retaining walls are seldom more than a few hundred feet
long; if they are designed conservatively, the added costs are of limited sig-
nificance. Flood walls, on the other hand, are usually the primary feature of
a local protection project. They must be designed for the most economical
cross section per unit length of wall, because they often extend for great dis-
tances . Added to this need for an economical cross section is the requirement
for safety. The consequences of failure for a flood wall are normally very
great since it protects valuable property and human life. Thus, the design of
retaining and flood walls is a complex process involving safety and economy
factors, and design must be executed in a logical, conservative manner based
on the function of the wall and the consequences of failure. Design documents
should describe the decisions leading to the final degree of conservatism.
2-14. Stability Considerations. An adequate assessment of stability must

include a rational assessment of loads and must account for the basic struc-
tural behavior, the mechanism of transmitting compressive and shearing loads
to the foundation, the reaction of the foundation to such loads, and the
secondary effects of the foundation behavior on the structure.
Section IV. Coordination Between Disciplines
2-15. Engineering Team. A fully coordinated team of geotechnical and struc-

tural engineers, and hydraulic engineers where applicable, should ensure that
all pertinent engineering considerations are properly integrated into the
2-6
EM 1110-2-2502
29 Sep 89
overall design of a structure. Some of the critical aspects of design which

require coordination are:
a. Preliminary estimates of geotechnical and hydraulic data, subsurface

conditions, and types of structures which are suitable for the foundation.
b. Selection of design parameters, loading conditions, loading effects,

potential failure mechanisms, and other related features of the analytical
models.
c. Evaluation of the technical and economic feasibility of alternative

types of structures.
d. Constructability reviews in accordance with ER 1110-1-803.
e. Refinements of the preliminary structure configuration to reflect the

results of detailed site explorations, material availability studies, labora-
tory testing, and numerical analysis.
f. Modification to the structure configuration during construction due to

unexpected variations in the foundation conditions.
Section V. Geotechnical Investigations
2-16. Planning the Investigation.
a. Purpose. The purpose of the geotechnical investigation for wall

design is to identify the type and distribution of foundation materials, to
identify sources and characteristics of backfill materials, and to determine
material parameters for use in design analyses. Specifically, the information
obtained will be used to select the foundation type and depth, design the
foundation, estimate backfill pressures, locate the ground-water level, esti-
mate settlements, and identify possible excavation problems. For flood walls,
foundation underseepage conditions must also be assessed. Detailed informa-
tion regarding subsurface exploration techniques may be found in
EM 1110-1-1804 and EM 1110-2-1907.
b. Review of Existing Information. The first step in an investigational

program is to review existing data so that the program can be tailored to con-
firm and extend the existing knowledge of soil and rock conditions.
EM 1110-1-1804 provides a detailed listing of possible data sources; important
sources include air photographs, geologic maps, surficial soil maps, and logs
from previous borings. In the case of flood walls, study of old topographic
maps can provide information on past riverbank or shore geometry and identify
likely fill areas.
2-17. Foundation Exploration and Site Characterization.
a. Preliminary Exploration. Where possible, exploration programs should

be accomplished in phases, so that information obtained in each phase may be
2-7
EM 1110-2-2502
29 Sep 89
used advantageously in planning later phases. The results of each phase are
used to "characterize" the site deposits for analysis and design by developing
idealized material profiles and assigning material properties. For long,
linear structures like flood walls, geophysical methods such as seismic and
resistivity techniques often provide an ability to rapidly define general con-
ditions during the preliminary phase at a modest cost. In alluvial flood-
plains, air photograph studies can often locate recent channel fillings or
other potential problem areas. A moderate number of borings should be ob-
tained at the same time to refine the site characterization and to "calibrate"
geophysical findings. Borings should extend deep enough to sample any mate-
rials which may affect wall performance; a depth of twice the wall height
below the ground surface can be considered a conservative "rule of thumb."
For flood walls where underseepage is of concern, a sufficient number of the
borings should extend deep enough to establish the thickness of any pervious
strata.
b. Detailed Exploration. The purpose of this phase is the development of

detailed material profiles and quantification of material parameters. The
number of borings should typically be two to five times the number of pre-
liminary borings. No exact spacing is recommended, as the boring layout
should consider geologic conditions and the characteristics of the proposed
structure. Based on the preliminary site characterization, borings should be
situated to confirm the location of significant changes in foundation condi-
tions as well as to confirm the continuity of apparently consistent foundation
conditions. At this time, undisturbed samples should be obtained for labora-
tory testing and/or in situ tests should be performed.
c. Additional Exploration. In some cases, additional exploration phases

may be useful to resolve questions arising during detailed design, and/or to
provide more detailed information to bidders in the plans and specifications.
2-18. Testing of Foundation Materials.
a. General. Procedures for testing soils are described in

EM 1110-2-1906. Procedures for testing rock specimens are described in the
Rock Testing Handbook (U. S. Army Engineer Waterways Experiment Station (WES)
1980). Much of the discussion on use of laboratory tests in EM 1110-1-1804
and EM 1110-2-1913 also applies to wall design. For wall design, classifica-
tion and index tests (water content, Atterberg limits, grain size) should be
performed on most or all samples and shear tests should be performed on
selected representative undisturbed samples. Where settlement of fine-grained
foundation materials is of concern, consolidation tests should also be per-
formed. The strength parameters (|> and c are not intrinsic material prop-
erties but rather are parameters that depend on the applied stresses, the
degree of consolidation under those stresses, and the drainage conditions dur-
ing shear. Consequently, their values must be based on laboratory tests that
appropriately model these conditions as expected in the field.
b. Coarse-Grained Materials. Coarse-grained materials such as clean

sands and gravels are sufficiently pervious that excess pore pressures do not
2-8
EM 1110-2-2502
29 Sep 89
develop when stress conditions are changed. Their behavior can be modeled for
static analyses (earth pressure, sliding, bearing) using parameters from
consolidated-drained (S) tests. Failure envelopes plotted in terms of total
or effective stresses are the same, and typically exhibit a zero c value and
a <j) value in the range of 25 to 40 degrees. Because of the difficulty of
obtaining undisturbed samples of coarse-grained foundation materials, the §
value is usually inferred from in situ tests or conservatively assumed based
on material type. Where site-specific correlations are desired for important
structures, laboratory tests may be performed on samples recompacted to simu-
late field density.
c. Fine-Grained Materials.
(1) When fine-grained materials such as silts and clays are subjected to
stress changes, excess (positive or negative) pore pressures are induced
because their low permeability precludes an instantaneous water content
change. Undrained (Q or R) tests model such behavior. Shear strength envel-
opes for undrained tests plotted in terms of total stresses exhibit a non-zero
c parameter. However, if plotted in terms of effective stresses, the c
parameter is small (zero for all practical purposes) and the friction angle
will be essentially equal to that from a drained test. Reasonable estimates
of the drained friction angle <)>' can often be made using correlations with
the plasticity index (Figure 2-4).
40- T T T T T I T T T T
35-
-St. Louis District

30-J correlation (136 pts) 1976
(0
© Kenney (1959)
© 25-
l_
O»
Q>
O 20-
WES correlation
(TR3-604) 30 pts
15- 1962
10-
11 11 11 1111 i i i 11 i 1111 11 1111 i i 111111 11 11 | i 11 i | i i 11 | i 11 11 i 11 11 i i i 1111 i i

5 10 15 20 25 30 35 40 45 50 55 60 65
Plasticity Index
Figure 2-4. Drained friction angle versus plasticity index
2-9
IpSipÄpS^
EM 1110-2-2502
29 Sep 89
(2) At low stress levels, such as near the top of a wall, the undrained
strength is greater than the drained strength due to the generation of nega-
tive pore pressures which can dissipate with time. Such negative pore pres-
sures allow steep temporary cuts to be made in clay soils. Active earth
pressures calculated using undrained parameters are minimum (sometimes nega-
tive) values that may be unconservative for design. They should be used, how-
ever, to calculate crack depths when checking the case of a water-filled
crack.
(3) At high stress levels, such as below the base of a high wall, the
undrained strength is lower than the drained strength due to generation of
positive pore pressures during shear. Consequently, bearing capacity and
sliding analyses of walls on fine-grained foundations should be checked using
both drained and undrained strengths.
(4) Certain materials such as clay shales exhibit greatly reduced shear
strength once shearing has initiated. For walls founded on such materials,
sliding analyses should include a check using residual shear strengths.
2-19. In Situ Testing of Foundation Materials.
a. Advantages. For designs involving coarse-grained foundation mate-

rials, undisturbed sampling is usually impractical and in situ testing is the
only way to obtain an estimate of material properties other than pure assump-
tion. Even where undisturbed samples can be obtained, the use of in situ
methods to supplement conventional tests may provide several advantages:
lower costs, testing of a greater volume of material, and testing at the
in situ stress state. Although numerous types of in situ tests have been
devised, those most currently applicable to wall design are the standard pene-
tration test, the cone penetration test, and the pressuremeter test.
b. Standard Penetration Test. The standard penetration test or SPT (ASTM

D-1586) is routinely used to estimate the relative density and friction angle
of sands using empirical correlations. To minimize effects of overburden
stress, the penetration resistance, or N value, is usually corrected to an
effective vertical overburden stress of 1 ton per square foot using an
equation of the form:
N' = C„N [2-1]
where
N' = corrected resistance
C = correction factor
N
N = measured resistance
2-10
EM 1110-2-2502
29 Sep 89
Table 2-1 and Figure 2-5 summarize the most commonly proposed values for C .
The drained friction angle <|)' can be estimated from N' using Figure 2-6.
The relative density of normally consolidated sands can be estimated from the
correlation obtained by Marcuson and Bieganousky (1977):
r 2l1/2
Dr - 11.7 + 0.76 |222(N) + 1600 - 53(p^Q) - 50(0^ |J [2-2]
where
p' = effective overburden pressure in pounds per square inch
C = coefficient of uniformity
Correlations have also been proposed between the SPT and the undrained
strength of clays. However, these are generally unreliable and should only be
used for very preliminary studies and for checking the reasonableness of SPT
and lab data.
c. Cone Penetration Test. The cone penetration test, or CPT (ASTM

D 3441-79), is widely used in Europe and is gaining considerable acceptance in
the United States. The interpretation of the test is described by Robertson
and Campanella (1983). For coarse-grained soils, the cone resistance q has
been empirically correlated with standard penetration resistance (N value).
The ratio (q /N) is typically in the range of 2 to 6 and is related to median
grain size (see Figure 2-7) . The undrained strength of fine-grained soils may
be estimated by using a modification of bearing capacity theory:
k
where
p = the in situ total overburden pressure
N = empirical cone factor typically in the range of 10 to 20

Js.
The N value should be based on local experience and correlation to labora-

tory tests. Cone penetration tests also may be used to infer soil classifica-
tion to supplement physical sampling. Figure 2-8 indicates probable soil type
as a function of cone resistance and friction ratio. Cone penetration tests
may produce erratic results in gravelly soils.
2-11
EM 1110-2-2502
29 Sep 89
Table 2-1
SPT Correction to 1 tsf (2 ksf)
Correction Factor C.
N
Seed, Peck,
Effective Arango, Peck Hanson, and
Overburden and Chan and Bazaraa Thornburn
Stress (1975) (1969) (1974)
(kips/sq ft) Seed P & B PH & T
0.20 2.25 2. 86
0.40 1.87 2 22 1.54
0.60 1.65 1 82 1.40
0.80 1.50 1 54 1.31
1.00 1.38 1 33 1.23
1.20 1.28 1 18 1.17
1.40 1.19 1 05 1.12
1.60 1.12 0 99 1.08

1.80 1.06 0 96 1.04
2.00 1.00 0 94 1.00
2.20 0.95 0 92 0.97
2.40 0.90 0 90 0.94
2.60 0.86 0 88 0.91
2.80 0.82 0 86 0.89
3.00 0.78 0 84 0.87
3.20 0.74 0 82 0.84
3.40 0.71 0 81 0.82
3.60 0.68 0 79 0.81
3.80 0.65 0 .78 0.79
4.00 0.62 0 .76 0.77
4.20 0.60 0 .75 0.75
4.40 0.57 0 .73 0.74
4.60 0.55 0 .72 0.72
4.80 0.52 0 .71 0.71

5.00 0.50 0 .70 0.70
2-12
EM 1110-2-2502
29 Sep 89
SPT CORRECTION TO TSF (2 ksf)
c IS
Figure 2-5. SPT correction to 1 tsf (2 ksf)
o
o
L
o
a
•e- «--
c
Ci) Schmertmonn (1975)
S(^\ Bowles (1382)

vt/ after Meyerhof (1956)
y\ (?) Dos (IdS'l)
g>
c
o M) Peck,Hanson & Thornburn (1974) •
u
a
-1
10 20 30 10 60
Penetration Resistance, N'
Figure 2-6. <|>' versus N' for granular materials
2-13
EM 1110-2-2502
29 Sep 89
qc , bars, N. blows/foot (I bar= lOOkPa )= 1.04 tsf
aAYEY SILTS SANDY SILT

& SILTY CLAY & SILT SILTY SAND
A\
m.
/# A
&
Ä?i
i
*r"^* §L -^
a
0.001 0.01 0.1 1.0
MEAN GRAIN SIZE. D^ , mm
Figure 2-7. a /N versus D „ (after

c 50
Robertson and Campanella 1983)
400
1 1 1 1 1
SAWS /
zoo / —
/ SILTY SAMS
/ /
100 ~ / / —
BO / / —
60 — y / SAWW SILTS ' _
S / * SILTS /
40 / —
•' S // f/
S /CLAYEY SILTS /
S ' A SILTY CLAYS/
20 -
' / '
/ /
10 _
sS /'
6 -
- PEAT
y s
/
s s
s
2 _
- s
• _
1 1 1 1 1
FRICTION RATIO, FR.-/.

Figure 2-8. Soil classification from cone penetrometer
(after Robertson and Campanella 1983)
2-14
EM 1110-2-2502
29 Sep 89
d. Pressuremeter Test. The pressuremeter test, or PMT, also originated

in Europe. Its use and interpretation are discussed by Baguelin, Jezequel,
and Shields (1978). Test results are normally used to directly calculate
bearing capacity and settlements, but the test can be used to estimate
strength parameters. The undrained strength of fine-grained materials is
given by:
= Pi - Pho [2-4]
where
p = limit pressure
p; = effective at-rest horizontal pressure

ho
IC = a coefficient typically in the range of 2.5 to 3.5 for most clays.
Again, correlation with laboratory tests and local experience is recommended.
2-20. Backfill Materials. Selection of backfill materials is discussed in

Chapter 6. Every effort should be made to provide clean, free-draining back-
fill materials. Density and strength parameters should be determined from
tests on laboratory-compacted samples over a range of densities consistent
with expected specification requirements. Development of a local data base
and correlations for the properties of locally obtained backfill materials may
significantly reduce the need for testing. Figure 2-9 provides typical values
of the friction angle for use in preliminary designs. The soil type codes are
taken from the Unified Soil Classification System, shown in Technical Memo-
randum 3-357, prepared by the U. S. Army Engineer Waterways Experiment Station
in 1960. The data for this figure were assembled from a wide variety of
design references.
2-21. Design Strength Selection. As soils are heterogeneous (or random)

materials, strength tests invariably exhibit scattered results. The guidance
contained in EM 1110-2-1902 regarding the selection of design strengths at or
below the thirty-third percentile of the test results is also applicable to
walls. For small projects, conservative selection of design strengths near
the lower bound of plausible values may be more cost-effective than performing
additional tests. Where expected values of drained strengths (<|> values) are
estimated from correlations, tables, and/or experience, a design strength of
90 percent of the expected (most likely) value will usually be sufficiently
conservative. In the case of rock foundations, the strength of intact rock,
the strength and orientation of discontinuities, and the orientation of joints
relative to the possible failure modes must all be considered in selecting
design strengths.
2-15
EM 1110-2-2502
29 Sep 89
I I I I I I
esuea
7 c
o
<o
8SOO"l
«'S
esuea
O 3 o
00 0} >
o
-
esoo !
o
at
,o
9SU9Q n
o < 1
M
60
esoon
00
t/)
<
00
9SUSQ a
cd
Ixl o
I— •rl
< 4J
2 CJ
esooi •H
M
esuea ON
I
a.
C/) u
00
esoon
oo
esocn
U. I i i i i l i
in o in
ro 4M
seejßea u| ' $' 3H9NV NOIlOiaJ
2-16
EM 1110-2-2502
29 Sep 89
CHAPTER 3
FORCES ON WALLS
3-1. General. Retaining walls and flood walls accommodate a difference in

soil or water elevation over a typically short horizontal distance. On one
side of the wall, the driving side, lateral forces exceed those on the oppo-
site, resisting side; the force difference and resulting moment are accommo-
dated by forces and pressures developed along the base. Lateral forces may be
related to gravity, water seepage, waves, wind, and earthquakes. This chapter
presents methods for calculating pressures and resulting forces on the driving
and resisting sides of walls. These are necessary to calculate the magnitude
and location of the base resultant force for overturning and bearing capacity
analysis. They are also required for the design of the structural elements of
the wall.
3-2. Limit-Equilibrium Analysis. The forces and pressures acting on a wall

are in fact highly indeterminate. Static equilibrium equations are insuffici-
ent to obtain a solution for lateral forces; additional assumptions must be
incorporated in the analysis. For nonlinear materials such as soils, this is
commonly and conveniently done by assuming that a "limit" or failure state
exists along some surface and that the shear force along the surface corre-
sponds to the shear strength of the material. With these assumptions, equi-
librium equations can be solved. Hence, this approach is commonly called
"limit-equilibrium analysis." To assure that the assumed failure does not in
fact occur, a factor (safety factor or strength mobilization factor) is ap-
plied to the material strength. It should be noted that this solution ap-
proach differs significantly from that commonly used for indeterminate struc-
tural analysis, where stress-strain properties and deformations are employed.
This limit-equilibrium approach provides no direct information regarding de-
formations; it is implied that deformations are sufficient to induce the fail-
ure condition. Deformations are indirectly limited to tolerable values by
judicious choice of a safety factor.
3-3. Relationship of Forces to Sliding Analysis. Forces calculated in accor-

dance with this chapter are not always equal to those calculated in a sliding
analysis (Chapter 4). The methods in this chapter are intended to produce
reasonable and somewhat conservative estimates of actual forces operative on
the wall. They can be used to perform a quick check on sliding stability as
described in paragraph 4-15. The sliding analysis for general cases (para-
graph 4-16) considers shear failure along the bases of a collection of inter-
acting free bodies (or wedges) that include both the wall and surrounding
soil. Sliding failure is prevented by applying a factor of safety on shear
strength equally on all segments of the failure surface. The lateral forces
calculated in the sliding analysis are a function of the sliding factor of
safety.
3-1
EM 1110-2-2502
29 Sep 89
Section II. Earth Pressures and Forces
3-4. Cohesionless Materials.
a. Active Earth Pressure. Cohesionless materials such as clean sand are

the recommended backfill for retaining walls. Large-scale tests (e.g.,
Terzaghi 1934; Tschebatarioff 1949; Matsuo, Kenmochi, and Yagi 1978) with
cohesionless (c = 0) backfills have shown that horizontal pressures are highly-
dependent on the magnitude and direction of wall movement. The minimum hori-
zontal pressure condition, or active earth pressure, develops when a wall ro-
tates about its base and away from the backfill an amount on the order of
0.001 to 0.003 radian (a top deflection of 0.001 to 0.003h , where h is the
wall height). As the wall moves, horizontal stresses in the soil are reduced
and vertical stresses due to backfill weight are carried by increasing shear
stresses until shear failure is imminent (see Figure 3-la).
b. Passive Earth Pressure. If a wall is moved toward the backfill,

horizontal stresses increase and shear stresses reverse direction, first de-
creasing and then increasing to a maximum at failure (see Figure 3-lb). Be-
cause the horizontal stress component along the shear planes is resisted by
both shear stress and vertical stress components, higher horizontal stresses
can be developed than for the active pressure case. Development of the maxi-
mum possible horizontal stress, or passive pressure, requires much larger wall
rotations than for the active case, as much as 0.02 to 0.2 radian. It should
be noted that the deformation required to mobilize one-half of the passive
pressure is significantly smaller than that required for full mobilization.
c. At-Rest Earth Pressure. If no wall movement occurs, the lateral

pressure condition is termed the at-rest pressure.
d. Lateral Earth Pressure Coefficient K. The ratio of the horizontal

effective stress to the vertical effective stress in a cohesionless soil mass
can be expressed by the earth pressure coefficient K . Typical relationships
between the K value and wall movements are shown in Figure 3-2. The value
of K can be obtained for active (K ) and passive (K ) conditions using
limit-equilibrium methods. Empirical equations are available for the at-rest
value (K ) as described in paragraph 3-10.
o
e. Conditions Affecting Earth Pressure. For complicated backfill condi-
tions, at-rest earth forces can be estimated using the general wedge method
combined with factored soil strengths as described in paragraph 3-13. If the
mode of wall movement is other than base rotation, the earth pressure and its
distribution may differ considerably from any solutions herein and other anal-
ysis techniques are required (see paragraph 3-15g). Also, compaction of the
backfill behind a wall can produce horizontal pressures in excess of at-rest
pressures near the top of a wall as discussed in paragraph 3-17.
3-2
.-. - ;
EM 1110-2-2502
29 Sep 89
O.OOIh - 0.003h
\Jm\J\J 11 DI
JW/M t
/
1
h I
/
/
/
f
ÜW
d0= ai-resf pressure
•- da= active pressure
cr3=crQ cr3=o-0 q +0"
a. Development of active earth pressure
0.02h - 0.2h
m*m\
\
\
\ h
a, H •°,
\
\
+T \
i
7MM
C£= at-rest pressure
a?- passive pressure
o-3=cr0
b. Development of passive earth pressure
Figure 3-1. Development of earth pressures for a cohesionless material
3-3
EM 1110-2-2502
29 Sep 89
OC 10 UJ
CE
CO
8
CO
CO
LÜ
6 CO
DC 5 UJ
cc
Q_ 4 a.
TERZAGHI
3
< a:
LÜ
<
LÜ
>
I/)
< 0.8 0.8 <
/-LOOSE 0.6
Lu
0.6 / SAND _ 0.5
O 0.5
PRINCETON 0.4
o
0.4
0.3
TESTS MEDIUM
SAND J_ 0.3 UJ
o
^
U.
0.2 r DENSER 0.2 ?
/ SANDX UJ
UJ o
o
o 0.1 .Li 0.1 o
0.06 0.04 0.02 0 0.004
WALL ROTATION -^- WALL ROTATION
PASSIVE CASE ACTIVE CASE

Figure 3-2. Relationship of earth pressures to wall movements
(after Department of the Navy 1982b)
3-4
EM 1110-2-2502
29 Sep 89
3-5. Cohesive Materials.
a. Strength Properties. So-called cohesive materials, typically fine-

grained soils such as clay, exhibit shear strength under zero confining stress
when loaded rapidly. The strength at zero confinement is expressed by the
parameter c , or cohesion. Cohesive materials are usually saturated or
nearly saturated because their small pore diameter attracts capillary water.
When stress changes are imposed (such as by wall movement) the soil attempts
to change volume. If low permeability prevents volume change from keeping
pace with the external stress change, pressure changes are induced in the pore
water. What appears to be stress-independent strength (cohesion) is, for the
most part, the combined effects of frictional resistance between soil parti-
cles and induced pore pressure changes. Pore water tension at low stresses
permits vertical cuts in clay; however, such cuts eventually fail as negative
pore pressures dissipate and water content increases. Horizontal pressures in
cohesive materials are related to the soil's permeability and pore pressure
response during shear in addition to wall movement. Therefore they are time
dependent.
b. Use as a Backfill Material. It is strongly recommended that cohe-

sionless materials such as clean sands be used for wall backfill materials.
Cohesionless materials have more predictable properties than cohesive mate-
rials, are less frost susceptible, and provide better drainage. However,
there are certain instances (such as walls adjacent to impervious clay cutoffs
in flood-control structures) where clay backfills may be unavoidable.
c. Short- and Lonq-Term Analyses. Solutions are included herein for

earth pressures in the terms of the general case involving both the c and <|)
parameters. Where cohesive backfills are used, two analyses (short-term and
long-term) are usually required with different sets of strength parameters in
order to model conditions that may arise during the life of the wall.
Strength tests are further discussed in Chapter 2, Section V.
(1) Short-Term Analyses. These analyses model conditions prevailing

before pore pressure dissipation occurs, such as the end-of-construction con-
dition. For these analyses, unconsolidated-undrained (Q) test parameters are
appropriate. Often these tests yield a relatively high c value and a low or
zero <|) value. Calculations may indicate that the soil is in tension to sig-
nificant depths and exerts zero pressure on the wall; thus, the short-term
analysis alone will seldom govern wall design. However, the zone of theoreti-
cally negative soil pressure may correspond to cracking and should be assumed
to crack as described in paragraphs 3-15f and 4-18. Water entering these
cracks may exert significant horizontal pressure on a wall. Therefore, short-
term stability analyses should include a check of the effect of water pressure
in tension cracks.
(2) Long-Term Analyses. These analyses model conditions prevailing

after shear-induced excess pore pressures have dissipated. (Dissipation
herein includes negative pore pressures increasing to zero.) For long-term
analysis, consolidated-drained (S) test parameters are appropriate. These
3-5
EM 1110-2-2502
29 Sep 89
tests usually yield a relatively high § value and a relatively low or zero
c value.
d. Overconsolidated "Swelling" Clay Soils. For highly overconsolidated

and/or "swelling" clay soils, lateral pressures may be developed in excess of
those calculated using drained or undrained strength parameters. These pres-
sures cannot generally be determined using limit-equilibrium techniques (see,
e.g., Brooker and Ireland 1965). The use of such soils around retaining walls
should be avoided.
3-6. Pressures in Soil-Water Systems. Soil grains are able to transmit shear
stresses; water cannot. Consequently, effective pressures in soil may differ
on horizontal and vertical planes but water pressures cannot. Effective soil
pressures are therefore separated from water pressures in calculations. If
the value of K is established, horizontal effective stresses may be calculated
by multiplying the effective vertical stress at any point by the corresponding
K value (see Figure 3-3) . To obtain the total horizontal pressure, the ef-
fective horizontal pressure is added to the water pressure. Where more than
one soil layer is present, vertical pressures increase continuously with depth
but the horizontal pressure diagrams may be discontinuous as shown. Combining
water pressures with effective earth pressures is further discussed in para-
graphs 3-15 and 3-18.
3-7. Design Earth Pressures and Forces, Driving Side.
a. Use of At-Rest Earth Pressures. The driving side of a retaining wall

or flood wall is defined as that side on which soil and/or water exerts a
horizontal force tending to cause instability. Designers have often assumed
active earth pressure on the driving side because movements required to de-
velop active pressures are small. However, several reasons exist to design
walls for at-rest pressures. Because designs incorporate factors of safety,
walls may be quite rigid and pressures may be greater than active. Hydraulic
structures in particular are designed using conservative criteria that result
in relatively stiff wall designs. Walls founded on rock or stiff soil founda-
tions may not yield sufficiently to develop active earth pressures. Even for
foundations capable of yielding, certain experiments with granular backfill
(Matsuo, Kenmochi, and Yagi 1978) indicate that, following initial yield and
development of active pressures, horizontal pressures may in time return to
at-rest values. Another reference (Casagrande 1973) states that the gradual
buildup of the backfill in compacted lifts produces greater-than-active pres-
sures as do long-term effects from vibrations, water level fluctuations, and
temperature changes.
b. Estimation of Operative Pressures. Design analyses require an esti-

mate of the expected "operative" (nonfailure) pressures on the wall for over-
turning and bearing capacity analyses and structural design. Therefore, walls
should be designed to be safe against overturning and bearing failure for at-
rest earth pressure conditions, and structural elements should be designed
assuming at-rest earth pressures on the driving side. The lateral soil forces
calculated using the multiple wedge sliding analysis described in Chapter 4
3-6
EM 1110-2-2502
29 Sep 89
UJ CO
CD
3 Rt
</> 6
to
ill i-i
rr •H
a. O
03
_i
■< to
i— 01
z t-H
o C
o
f»J
re CO
o 4>
O
U
CO
cu
u
2
to
to
CO
l-l
a.
UJ
oc i-i
=) (0
«/> 4-1
«/> C
o
IÜ
•H
o
_J J3
■<
o -O
IS
h- CO
(£
LÜ r-i
> CO
O
•H
4-1
>-l
a>
>
t/>
+-
a
1 +-
UJ
I—
CO
1
» (0 o +- CO
, to \ CO
o UJ Q_
o S£ >C
• 4- a
(0 +- %
z
<t
o o .
_l e t\l M
o . X,
Ul
_J —1 _J
to . >^ O * * O u_
* " CO "CO * o
a:
Q_
-B*
N N N N
3-7
EM 1110-2-2502
29 Sep 89
are in the at-rest pressure range when a safety factor of 1.5 is obtained.
c. Compaction and Surcharge Effects. Where significant compaction effort

is specified for the backfill, design earth pressures should be increased
beyond the at-rest values for depths above a "critical" depth as described in
paragraph 3-17. Where surcharges are expected above the backfill (in stock-
piles, rails, footings, etc.), the additional horizontal earth pressure due to
the surcharge should be determined as discussed in paragraph 3-16 and super-
imposed on the at-rest pressure diagram. Examples of these effects are given
in Appendix M.
3-8. Design Earth Pressures and Forces, Resisting Side.
a. Background. The resisting side of a wall is defined as that side

where soil and/or water provide a lateral reaction tending to resist instabil-
ity. The maximum earth force that can be developed is the passive earth
force. However, for a wall in equilibrium, the actual resisting-side force
will typically be smaller than the passive force as the forces on the driving
side, base, and resisting side taken together must satisfy static equilibrium.
The resistances to the driving-side force provided by the resisting-side force
and the base shear force, respectively, are indeterminate. Allocation of the
total resistance between these two forces is judgmental.
b. Estimation of Passive Resistance. A conservative and convenient de-

sign approach is to assume the resisting-side force is zero for overturning
and bearing capacity analyses and for structural design. However, in some
cases, such as walls with relatively deep foundations, it may be desirable to
consider some lateral resistance for these analyses. To justifiably assume a
non-zero resisting-side force, the material must not lose its resistance char-
acteristics with any probable change in water content or environmental condi-
tions and must not be eroded or excavated during the life of the wall. If
such assumptions can be justified, at-rest conditions may be conservatively
assumed on the resisting side. Resisting-side pressures and forces generally
should not be assumed to exceed at-rest conditions when calculating the base
resultant force and location and when designing structural components. How-
ever, if the driving-side earth force exceeds the sum of the resisting side
at-rest earth force (if present) and the maximum available base shear force
calculated using unfactored shear parameters, the additional required resis-
tance should be assumed to be provided by additional resisting-side pressure.
In no case should the resisting-side earth pressure exceed one-half the pas-
sive pressure calculated using unfactored shear strengths for overturning and
bearing capacity analyses and structural design.
c. Horizontal Force Allocation. To summarize, the horizontal force

allocation for overturning analysis, bearing capacity analysis, and design of
structural components should be computed as follows:
(1) Calculate the at-rest effective earth force on the driving side
(paragraphs 3-10 through 3-13) . Superimpose surcharge effects if present
(paragraph 3-16). Add water pressures, if present.
3-8
EM 1110-2-2502
29 Sep 89
(2) Assume that the resisting-side earth force equals zero or calculate
and apply the at-rest earth force on the resisting side of the wall, if justi-
fied (paragraphs 3-10 through 3-13). Add water forces if present.
(3) Assume that the horizontal component of the base resultant is equal
to the difference between the horizontal forces from (1) and (2).
(4) If the maximum available base shear force is exceeded, assume that
the remaining horizontal force is resisted by mobilizing a greater fraction of
passive pressure so long as not more than one-half the available passive force
is used. (This may occur where the resisting-side soil is strong relative to
the driving-side and base soils.)
d. Sliding Stability Check. Sliding stability should be checked using

the single or multiple wedge methods found in paragraphs 4-15 and 4-16,
respectively.
3-9. Design Earth Pressures and Forces on the Base.
a. Calculation of Resultant Force on Base. The resultant force on the

base, its direction, and its location must be such that the wall is in static
equilibrium for the "operative" loads (see Figure 3-4) . In Figure 3-4a, the
vertical component of the resultant is equal and opposite the summed weights
of the "structural wedge" and the horizontal component is equal to the differ-
ence of the driving-side and resisting-side forces. Figure 3-4b illustrates a
more complicated example including water and a sloping base with a key. The
vertical and horizontal components of the base uplift force are calculated
from base water pressures obtained from a seepage analysis. The remaining
vertical and horizontal forces required for equilibrium are provided by com-
ponents of the base shear force T and effective normal force N' . An over-
turning analysis as described in Chapter 4 must be performed in order to
determine the effective normal force N' and its location.
b. Computation of Base Pressures. The effective earth pressure on the

base is assumed to vary linearly and N' is applied at the centroid of the
pressure diagram. When the resultant falls within the middle one-third of the
base, the effective base pressures q' are calculated by the following
equation:
q -(£)("?)
where
N' = effective normal force on base of structure
B = width of base of structure
e = eccentricity of N' from center of base
3-9
EM 1110-2-2502
29 Sep 89
Ö -
c =
CO T3
3: c:
H
c=
-r- *Ö
09 ■o P
O 3 5
Ü ^~
> u CU
rc CO
Kl '~ re
4->
*a
II o b0
C
C
en •H
OJ o
s_ PH
o CO
4-
r—
.e
4J
r— •H i-i
<o &
re
<+-
o
i—1 &
iH
3 re m
c & o
es o
T3 cu
-t-> O DO
"to O re
> Ü i-l .a
w 3
e
■ • o
CD
,Q
« cu
CO CJ
o w >■
o
o Fu
3C -o
W c:
•
ii -t- •3"
f— H CO
cu
00
•H
i-H
i-H
bO
C
re
4-)
u
CU
1—1
8"
a? CO
i
re
QQ
3-10
EM 1110-2-2502
29 Sep 89
This is shown in Figure 3-5, a and b. If the resultant falls outside the
middle one-third of the base, i.e., e is greater than B/6 , as shown in
Figure 3-5c, the pressure distribution is triangular with a maximum pressure
equal to
^■I(B^)
The base will be in compression over a distance b from the toe computed as
b = | (B - 2e) [3-3]
Refer to Appendix N for example computations.
3-10. At-Rest Earth Pressure Equations.
a. Horizontal Backfill. For the special case of a horizontal backfill

surface and a normally consolidated backfill (no compaction or other prestress
effects) the at-rest pressure coefficient K can be estimated from Jaky's
(1944) equation
K - 1 - sin $' [3-4]
and the lateral earth pressure computed by
Po = y'Koz
where
())' = drained internal friction angle
Y' = effective unit weight (moist or saturated above water table,

submerged or buoyant below water table)
z = depth below surface of backfill along a vertical plane
b. Sloping Backfills. For normally consolidated sloping backfills,

results of experiments to measure K are quite variable. The following
o
equation proposed by the Danish Code (Danish Geotechnical Institute 1978) is
recommended:
x
op K0 (1 + sin ß) [3-5]
3-11
EM 1110-2-2502
29 Sep 89
B
V T1 I
*-■ (DO * *)
<S' Irin
a. Simple wall, resultant in middle one-third of base
CTniln •= 0
■■®w
,(i)(B- ze)
b. Flood wall with sloping c. Pressure for resultant outside

base middle one-third
Figure 3-5. Base pressures
3-12
EM 1110-2-2502
29 Sep 89
Substituting Equation 3-4 in 3-5 gives:
K . - (1 - sin *') (1 + sin 6) [3-6]

op
and the lateral earth pressure computed by
=
Po y' Kopz
where ß is the slope angle from the horizontal, ß is positive for a soil
layer that slopes upward and away from the structure. Values for K and
K „ are given in Appendix E.
c. General Conditions. For walls with irregular backfill surfaces, non-

homogeneous backfills, surcharge loadings, and/or other complicating condi-
tions, empirical relationships for the at-rest pressure are not generally
available. For routine designs, an approximate solution for the horizontal
earth force may be obtained using Coulomb's active force equation or the gen-
eral wedge method with values of c and tan § multiplied by a strength
mobilization factor (defined in paragraph 3-11). Because this is an empirical
approach, results will differ slightly from calculations using Equations 3-4
through 3-6 where companion solutions can be obtained. Appendix E includes a
comparison of K values so obtained for both horizontal and sloping back-
fills. Figure 3-6 shows a comparison of Jaky's equation with Coulomb's equa-
tion for a horizontal backfill.
d. Resisting Side. Jaky's equation and the Danish Code equation may be
used to compute at-rest pressures for the resisting side for horizontal and
sloping soil surfaces, respectively. Example computations are shown in
example 7 of Appendix M and in Appendix N.
3-11. Strength Mobilization Factor.
a. Definition. The strength mobilization factor (SMF) is defined as the

ratio of the assumed mobilized or developed shear stress x along an assumed
slip surface to the maximum shear strength x of the soil material at fail-
ure. If an appropriate SMF value is assumed and applied to c and tan 0 ,
it allows calculation of greater-than-active earth pressures using Coulomb's
active force equation (paragraph 3-12) or the general wedge equation (para-
graph 3-13). Alternatively, the safety against sliding may be assessed by
calculating the average SMF along an assumed sliding surface from an equi-
librium analysis and comparing it to a recommended maximum value. These con-
cepts are illustrated in Figure 3-7. In equation form, the strength mobiliza-
tion factor may be expressed as:
SMF = — [3-7]
T
f
3-13
EM 1110-2-2502
29 Sep 89
Horizontal Backfill
.9
.8
.7
.6
o
st
.5
A "\.
.3
.2
10 20 30 40 50
PHI
-a- Jaky
-K- Coulomb With

SMF = 2/3
Figure 3-6. At-rest earth pressure coefficients
3-14
EM 1110-2-2502
29 Sep 89
t=f<c,4>> q,,<Dd = f<SMF>
Assume SMF = 2/3
Solve for P Solve for P
ACTIVE EARTH FDRCE AT-REST EARTH FDRCE
t=-T<cd,<J>d>
Assune global equilibrium

Solve for SMF
SLIDING
Figure 3-7. Application of the strength mobilization factor
3-15
EM 1110-2-2502
29 Sep 89
cr3'= 1
/ra'
-/-
Tf
0$ CTn Ö-,' cr
Figure 3-8. Mohr-Coulomb failure criterion
b. Developed Shear Stress. According to the Mohr-Coulomb failure

criterion (Figure 3-8) the shear strength on the failure plane is defined as
a tan <j>r + c [3-8]

n
where
C = effective normal stress

n
<|),c = shear strength parameters of soil (where <|> and c in the above
equation are drained strengths (<(» = <])' , c = c') for long-term
analysis and undrained (<|> = 0, c = S ) for short-term analysis of
cohesive materials).
The failure plane is inclined 45 + (|)/2 degrees from the plane of the major
principal stress. For limit-equilibrium analyses to be valid, the assumed
slip surface must be inclined at this angle relative to the principal
stresses. In the Coulomb and general wedge methods, a plane slip surface is
assumed. Discontinuities in the backfill surface, surcharges, and wall fric-
tion all cause variation in the principal stress directions and induce
3-16
EM 1110-2-2502
2 9 Sep 89
curvature in the slip surface. Assuming that the plane slip surface approxi-
mation is valid and is properly oriented relative to the principal stresses,
the shear stress on it is:
T - SMF (c) + a1 SMF (tan *) [3-9]

n
Thus, the shear stress on a presumed slip surface is taken to be a function of

the shear strength parameters, the effective normal stress, and the strength
mobilization factor.
c. Developed Shear Strength Parameters. Multiplying the shear strength

parameters (c and tan (j>) by the appropriate SMF reduces them to the
"developed" values (c and tan <j> ) assumed to be operative in equilibrium
conditions. The developed shear strength parameters, the actual shear
strength parameters, and the SMF are related as follows:
tan <f>, c.
SMF - T^ = — [3-10]
tan <j> c
To estimate at-rest pressures for design using Coulomb's active earth pressure
equation or the general wedge equation, the SMF should be taken as 2/3
(0.667). K values so obtained are compared with Jaky's equation in Fig-
ure 3-6. The Coulomb equation with an SMF of 2/3 is compared to the Danish
Code and Jaky equations in Appendix E. It should be noted that as the ratio,
tan ß/tan <|> , exceeds 0.56, the lateral earth force computed by the Coulomb or
general wedge equations using an SMF =2/3 will be increasingly larger than
that given by computing the earth force using a K given by the Danish Code
equation, for those conditions where the Danish Code equation applies. There-
fore, computing at-rest earth loadings using the Coulomb or general wedge
equations for a sloping backfill when tan ß/tan <j) exceeds 0.56 will be con-
servative (see Appendix E).
3-12. Earth Force Calculation, Coulomb's Equations.
a. General.
(1) Coulomb's equations solve for active and passive earth forces by
analyzing the equilibrium of a wedge-shaped soil mass. The mass is assumed to
be a rigid body sliding along a plane slip surface. Design (at-rest) earth
pressures and forces may be estimated using developed shear strength param-
eters (Equation 3-10) corresponding to an SMF of 2/3 in the Coulomb active
earth force equation. The Coulomb equations have the advantage of providing a
direct solution where the following conditions hold:
3-17
EM 1110-2-2502
29 Sep 89
(a) There is only one soil material (material properties are constant).
There can be more than one soil layer if all the soil layers are horizontal.
(b) The backfill surface is planar (it may be inclined).
(c) The backfill is completely above or completely below the water table,
unless the top surface is horizontal, in which case the water table may be
anywhere within the backfill.
(d) Any surcharge is uniform and covers the entire surface of the driving
wedge.
(e) The backfill is cohesionless, unless the top surface is horizontal,

in which case the backfill may be either cohesionless or cohesive.
(2) Although Coulomb's equation solves only for forces, it is commonly

expressed as the product of a constant horizontal pressure coefficient K and
the area under a vertical effective stress diagram. Assuming the concept of a
constant K is valid, horizontal earth pressures can be calculated as the
product of K times the effective vertical stress. The variation of the
Coulomb solution from a more rigorous log-spiral solution is generally less
than 10 percent, as shown in Figure 3-9.
b. Driving-Side Earth Force.
(1) The total active force P on a unit length of wall backfilled with
a cohesionless material (c = 0) is given by:
1 ... . a 1
P.-Jlf' - .2
A 2 sxn 6 cos oT K.ti
A [3-11]
and acts at an angle 8 from a line normal to the wall. In the above
equation (refer to Figure 3-10):
Y' = effective unit weight (moist or unsaturated unit weight if above the
water table, submerged or buoyant unit weight if below the water table)
Ö = angle of the wall face from horizontal (90 degrees for walls with a
vertical back face or structural wedge)
8 = angle of wall friction
K, = active earth pressure coefficient

A
h = height of fill against gravity wall or height of fill at a vertical
plane on which the force is being computed
3-18
EM 1110-2-2502
29 Sep 89
where
KA sin2 (6 + ♦) cos 6 [3_12]

A 2
re.
sin 6 sin (6 ,N r , . /sin (» + 6) sin (♦ - B)]
-«)[! + Vsin (9 - 6) sin (6 + g)J
Examples 1 and 2 in Appendix M and the examples in Appendix N demonstrate the

use of Equation 3-12.
(2) When wall friction is neglected (8=0), Equation 3-12 reduces to:
K - sin2 (6 + <fr) _ [3_13]
2
sin 61[i + /sin d) sin ($ - g)T
\sin 6 sin (6 + g)J
(3) For the case of is no wall friction (8 = 0) and a vertical wall

(6 = 90 degrees),
v cos_i [3_14]
[»♦ v°'° *£p - c)]:
(4) For the special case of no wall friction, horizontal backfill sur-
face, and a vertical wall, Coulomb's equation for K reduces to:
K
A TTiff* - »"2 («* - !) "-15'
which is identical to Rankine's equation for this special case.
(5) As stated in paragraph 3-lie and demonstrated in Figure 3-6 and

Appendix E, a developed <j) angle computed by Equation 3-10 using an SMF of
2/3 can be used in Coulomb's equation to compute an earth pressure coefficient
close to that given by the Jaky or Danish Code equations.
3-19
EM 1110-2-2502
29 Sep 89
20
<
CL
>
o
o <
>
UJ
in
o z
o
Ll_
o
UJ
o
z
UJ
Q:
UJ
u_
o
<
UJ
>
UJ 1-
o <
> -
LÜ Lü
0_ (/I
z
o
o1
z
o
z
NOTE*
Log spiral calculations based upon Caquot
and Kerisel coefficients. Range of values
for Rankine Is from Influence of wall
friction on log spiral.
Figure 3-9. Comparison of active earth pressures (after Driscoll 1979)
3-20
EM 1110-2-2502
29 Sep 89
0=90'
w
Figure 3-10. Variables used in Coulomb equation
3-21
EM 1110-2-2502
29 Sep 89
(6) For the horizontal component of the earth force acting on a vertical
plane, with no wall friction, the term (1/sin 0 cos 8) in Coulomb's equation
is equal to unity. Thus, Equation 3-11 reduces to
P
AH = (I)V h' [3 16]
"
(7) If total stress or undrained strength parameters are used and there
is a cohesion term c it has the effect of reducing the active earth force
2
P
AH = (j) KAY' h - 2CVK^ h + I?- [3-17]
For a backfill with a horizontal surface, K given in Appendix H, para-

graph H-2c, equals ^K • The second term is the reduction in the active
force due to the effect of cohesion on the slip plane and the third term ac-
counts for the shortened length of slip plane due to the effect of a tension
crack. If the third term is neglected, and K is assumed constant with
depth, the active pressure can be obtained as the derivative of P with
respect to the depth from the top of the wall z :
z 2c,/S
PAH "V " I t3"18]
Refer to examples 5 and 8 of Appendix M for examples involving cohesion.
(8) Estimation of at-rest pressures using the SMF concept with

Coulomb's equation may give unreliable results for medium to highly plastic
cohesive materials. If these materials cannot be avoided in the area of the
driving side wedge, the at-rest pressure should be taken as the overburden
pressure times as empirical K value, such as from Massarsch's (1979) or
Brooker and Ireland's (1965) correlation of K with the plasticity index.
Because of the number of uncertainties about the behavior of cohesive mate-
rials, a degree of conservatism should be exercised in the selection of the ]
values. Also, the effects of short and long term conditions (paragraph 3-5c)
and compaction (paragraph 3-17) should be included in estimating the at-rest
pressure.
3-22
EM 1110-2-2502
29 Sep 89
Resisting-Side Earth Force.
(1) The Coulomb and general wedge equations assume a plane slip surface.
However, wall friction effects cause the actual slip surface at failure to be
curved. For active pressure calculations, the magnitude of error introduced
by the plane surface assumption is not significant, as shown in Figure 3-9
(Driscoll 1979). Coulomb's passive force equation, however, is grossly uncon-
servative where wall friction is present as shown in Figure 3-11 (Driscoll
1979) . However, where 8 is less than about one-third (j> , the error is
small. If wall friction is neglected, Coulomb's equation is therefore accept-
able. The Coulomb passive pressure coefficient for the case of no wall fric-
tion (8 = 0) and a vertical wall (0 = 90 degrees) is:
cos 2 9A [3-19]
Kp
fi1 /sin $ sin (j> + B)l2
L "\ £o71 J
For a horizontal backfill (ß = 0), this reduces to
1 + sin 4>
1 - sin $
tan
(«•♦IK [3-20]
(2) If total stress or undrained strength parameters are used and there
is a cohesion term c , it has the effect of increasing the passive earth
force ppH :
^PH \ KpY'h2 + 2c*^ h [3-21]
By differentiating p with respect to the depth from the top of the

PH
resisting wedge z , the passive pressure may be obtained as:
PPH - v'z + 2^ c [3-22]
3-13. Earth Force Calculation, General Wedge Method.
a. General. The general wedge method refers to a limit equilibrium

analysis of a set of assumed rigid bodies (soil and/or structural elements)
3-23
EM 1110-2-2502
29 Sep 89
300
<
DC
Q_
l/>
O
O
200
O Lü
Cd
>
1-
<
>
O Lü
-z. t/1
Z
Ld o
o1 100
z
o
z
Q
Ld
O
<
UJ
o
Ld
Q_
>
1—
< RANKINE^
>
DC
Lü
0= 40° , S= 10° -40"
in
z
o
o
NOTE:
Log spiral calculations based upon Caquot
and Kerisel coefficients.
Figure 3-11. Comparison of passive earth pressures (after Driscoll 1979)
3-24
EM 1110-2-2502
29 Sep 89
termed wedges. The horizontal earth force on the driving or resisting side of
a retaining structure may be estimated by such an analysis employing properly
chosen strength parameters. Where the special conditions listed in para-
graph 3-12a(l) apply, the weight of the sliding mass and orientation of the
critical sliding plane are unique functions of the backfill geometry and soil
properties, and Coulomb's equations provide direct solutions for the driving
and resisting earth forces. Where one or more of the variables in Coulomb's
equation cannot be accommodated as a single value (such as the case with mul-
tiple soils where not all of the soil layers are horizontal, location of the
water table, irregular backfills or where nonuniform surcharges are present),
the critical inclination of the sliding surface and, in turn, the gravity
forces (weight plus surcharges) on the sliding mass must be solved in order to
calculate the horizontal earth force. In these cases, this requires a trial
and error solution using the general wedge equation.
b. Use in Practice. When used with unfactored soil strength parameters,

the general wedge equations yield the active and passive earth forces. When
c and tan $ are factored by an SMF value of 2/3, solution of the driving-
side wedge provides an estimate of the at-rest earth forces (see para-
graph 3-12). An SMF of 2/3 is not used to compute the resisting wedge force
for the overturning, bearing, and structural design of the wall since a larger
resisting force than is acceptable would be computed. See paragraph 3-8 for
the procedure recommended to determine the resisting force for overturning and
bearing capacity analyses and structural design of the wall.
c. Driving Side Earth Force, General Wedge Method.
(1) Wedge Geometry and Forces. The geometry of a typical driving-side

wedge and its free-body diagram are shown in Figure 3-12. The angle of wall
friction and the shear force between vertical wedge boundaries are assumed to
be zero. The inclination of the slip surface a is that which maximizes the
earth force. Calculation of a is discussed in paragraphs 3-13c(2)
and 3-13c(4). If force equilibrium is satisfied, the forces on the wedge form
a closed-force polygon as shown in Figure 3-13. The equation for the effec-
tive horizontal earth force P exerted by a driving-side wedge on a wall or
EE
an adjacent wedge is given by the general wedge equation as:
(W + V) (1 - tan A, cot a) tan a Ü tan <|>,d - c,L

d
P_ __ _i +
EE 1 + tan $, tan a cos a ( 1 + tan <J>, tan a)
H P t3 231
\ ~ R " W "
3-25
EM 1110-2-2502
29 Sep 89
where
P = effective horizontal earth force contributed by wedge or wedge

segment
W = total wedge weight, including water
V = any vertical force applied to wedge
a = angle between slip plane and horizontal
U = uplift or buoyancy force acting on and normal to wedge slip plane
L = length along the slip plane of the wedge
H = any external horizontal force applied to the wedge from the left,
acting to the right
H = any external horizontal force applied to the wedge from the right,
acting to the left
P = internal water force acting on the side of the wedge free body (Pw
is equal to the net difference of the water force for wedge seg
ments with water on two vertical sides as shown in Figures 3-12
and 3-13.)
The developed strength parameters tan § and c, are as defined in para-

graph 3-11. Equation 3-23 is derived for failure occurring from left to
right. All values are positive in the directions indicated in Figure 3-12.
Refer to Appendix M for examples using Equation 3-23.
(2) Critical Value of Slip-Plane Angle.
(a) The critical value of a for a driving-side wedge with a horizontal

top surface and a uniform surcharge or no surcharge is:
a = 45° + ^ C3-24]
(b) For the special case of a backfill with a planar (flat or inclined)
top surface and a strip surcharge V , the following equation can be used to
compute the critical a value:
a = tan-1 J_-JU ?■ [3-25]
3-26
EM 1110-2-2502
29 Sep 89
a. Estimation of forces using slices
PEECI-2) and PEEG-2) ar© 1"ne

earth forces applied by
wedges 3 and I to wedge 2.
EEO-2)" these earth forces are
assumed to act horizontally.
EEO-2)
The force on the
structural wedge
is equal and
opposite to P,EEC3-2)
b. Free body of wedge 2
c. Derivation of force F
Figure 3-12. Wedge method on driving side
3-27
EM 1110-2-2502
29 Sep 89
r EEG-2)
WR
-«- "O N' tan <p
NOTE: P FORCES SHOWN WITH

VERTICAL SEPARATION
FOR CLARITY
a
^
Force on driving side of

structural wedge (slice 3)
is equal and opposite to
PEE(3-2)-The force PEE
added by the wedge is
nd acts
(PEE<3-2)- PEE<I-2) )a
to the right. The force
Pw is equal to PWR-PWL
and acts to the right.
Figure 3-13. Force polygon for wedge method on driving side
The above equation for a assumes that the backfill is completely above or
completely below the water table, but can be used when the water table is any-
where within the backfill with sufficient accuracy for design. The surcharge
V can have any arbitrary shape but must be contained entirely within the
driving wedge. The equations for c and c are:
(i) For a cohesionless backfill without a strip surcharge:
c, " 2 tan <|>, [3-26]
/tan B [3-27]
1 - tan tan ß - \tan *,
3-28
EM 1110-2-2502
29 Sep 89
(ii) For a cohesive or a cohesionless backfill with a strip surcharge:
4c, (tan <t>, + tan ß) 4V tan ßfl + tan <f>,j

2 tan2
*d Y(h + d c )
cj j > ^ [3-28]
2c.(1
d
- tan 4,d tan ß) 2V tan2 B[l + tan2 *,]
tan *d (1 - tan ^ tan 6) - tan 6 + - + + A r & [3_29]
c' y h - d_c>I
where
2cd(l - tan <(>d tan ß) 2v(l + tan2 *dj

+ [3 301
"" *d ,»H) -^ ^ -
These equations when applied to a cohesive backfill are subject to the limita-
tions described in paragraph 3-12b(8). The derivation of these equations is
shown in Appendix G. Examples using these equations are shown in Appendix M.
(c) For irregular backfills, obtaining the critical inclination of the

driving-side slip surface may require a trial-and-error solution. As a first
approximation, the backfill surface may be bounded by two inclined lines
originating from the top of the wall and the value of a may be calculated
using an "average" ß value between the two bounding lines (Figure 3-14), or
by introducing a surcharge as shown in Example 9 of Appendix M.
(3) Limitations of Critical Slip Plane Equations. The equations for c

and c are valid except when the strip surcharge V is too large or when
the slope of the top surface is too great. The maximum value for the strip
3-29
EM 1110-2-2502
29 Sep 89
2h
ßavg ~ ß at x = 2h
J8=i3 max
h = Wal! height
-JMW
ß=ß avg "• —
ß ~ Anin=0
Pava- P max ~ P m!n
Pmax calculated at
x = 2h
ß=ß min
immr
Critical value of <x is between a calculated

using ßmln and ßmax •Use ßavg for f,rst +rfal-
Figure 3-14. Wedge analysis for irregular backfill
3-30
EM 1110-2-2502
29 Sep 89
surcharge is determined by setting the denominator of the equation for c or

c equal to zero and solving for V . This value is:
Y(h2 - d2) tan <J>d + 2cd(h - dc)(l - tan * tan ß)

tax [3-3
2(l + tan2 <J>d)
When V > V the value of a is set by the location of the strip surcharge
max
as shown in Figure 3-15, and given by the equation
1M1 - tan-1 d c + (S) tan ß

=■ [3-32]
Even when V < V , a check should be made to be certain that the entire
max
strip surcharge lies on the top surface of the wedge as defined by the
2
calculated value of a . Also, when c, , „ . , .
1 + 4c < 0 , a is indeterminate.
This is an indication that the slope of the top surface is too great to be
sustained by the developed strength parameters tan $, and c, . See
example 8 in Appendix M for a solution to this problem.
(4) Layered Soils. The wedge equations imply a single set of strength
parameters along the wedge base. For layered soils, the wedge must be divided
into wedge segments, each with its base in a single soil. The wedge base
inclinations a are theoretically different in every soil (Figure 3-16a) ,-
calculation of an optimum solution (maximized earth force) for the set of a
values is tedious and cumbersome. Three approximate methods may be used:
(a) The critical inclination in each layer may be calculated according to

Equation 3-25 using the developed shear strength parameters for the soil along
the wedge base and using the slope angle ß at the top of each wedge segment
(see Figure 3-16a).
(b) The wedge segment bases may be assumed to have a constant inclination
a through all materials and the critical value (corresponding to the maximum
driving side force) may be calculated by trial using Equation 3-23 (see
Figure 3-16b).
(c) Alternatively, the critical slip-plane angle may be calculated (for

each layer below the top layer) by using the procedure presented in para-
graph G-7 of Appendix G (see example 6 in Appendix M).
3-31
EM 1110-2-2502
29 Sep 89
EDGE OF STRIP
SURCHARGE
SLIP PLANE
h
c- ~dc
tana- tan/3
tana= „ dc
+ tan/3 h - d c + S ton ß
S
-i = /"h - dc + StanjS \
Oc = tan
Figure 3-15. Surcharge effect on critical slip plane
3-32
EM 1110-2-2502
29 Sep 89
ft W I Oases
Ä
SOIL l\
1
1
•S4,r4^^
. 1
\l
SOIL 2
**/
SOIL 3 a
V\
«8^
SOIL A a
v \| .► ■
► • . ►
a. Wedge 1
<* =f (Pmox)
SOIL I Found by trial
SOIL 2
SOIL 4
b. Wedge 2
Figure 3-16. Wedge analysis in layered soil
3-33
EM 1110-2-2502
29 Sep 89
If the surfaces of all layers are horizontal, the critical slip plane may be
determined using Equation 3-24.
(5) Surcharges. The wedge method incorporates surcharge effects into the
resultant earth force if the surcharge force is added to the wedge weight.
However, it is preferable to calculate horizontal pressures due to surcharges
separately for the following reasons:
(a) The presence of a nonuniform surcharge alters the principal stress

directions, increasing the curvature of the slip surface, and increasing the
error associated with assuming a plane surface.
(b) Stresses induced by surcharges are distributed throughout a soil mass

in a manner that may considerably alter the point of application and dis-
tribution of earth pressure as further described in paragraph 3-16. Limit-
equilibrium techniques and the earth pressure coefficient concept do not
accurately predict such distributions.
(c) The additional pressures developed on the wall depend on the amount
of wall movement and may be twice as great for nonyielding walls as for
yielding walls.
The intent of this manual is to consider walls to be relatively rigid and to

design for at-rest conditions. Therefore, pressures and forces due to non-
uniform surcharges should be calculated in accordance with paragraph 3-16,
adding the results to the pressures and/or forces obtained from Coulomb's
equation or the general wedge equation. For the sliding analysis, surcharge
effects may be included directly in the wedge method weight calculations
because the sliding analysis considers only force equilibrium; thus, the point
of application of the forces does not matter. Examples 4 and 10 of Appendix M
demonstrate the calculation of horizontal pressures involving surcharges.
(6) Pressure Coefficients.
(a) Structural engineers are familiar with the use of Coulomb's equations
(paragraph 3-12) for the determination of earth pressure coefficients and the
use of these coefficients in determining pressures and forces acting on
retaining walls. These equations suffer from several limitations as discussed
in paragraph 3-12a(l). The general wedge equation (Equation 3-23) is not
subject to any of the limitations of Coulomb's equations and may be used to
solve for the lateral earth force on a wedge due to complicated geometry and
surface loading. If lateral earth pressure coefficients are derived from the
general wedge equation, these coefficients may be used in a rather simple
manner to solve complex earth pressure problems.
(b) Earth pressures can be calculated from general wedge method solutions
by assuming that pressures vary in a piecewise linear fashion and that the
slopes of the pressure diagrams are the product of densities and pressure
coefficients (K). The slopes may be considered the density of an "equivalent
fluid" loading the wall. These pressure coefficients are dependent on the
3-34
EM 1110-2-2502
29 Sep 89
problem geometry and are derived in Appendix H. It should be noted that pres-
sure coefficients (K values) below the water table may differ from those
above the water table in the same material as shown in Appendix H. One exam-
ple where the K value is different above and below the water table is the
case of a sloping backfill. Examples using pressure coefficients are shown in
Appendix M.
d. Resisting Side Earth Force, General Wedge Method.
(1) Wedge Geometry and Forces. The geometry of a typical resisting-side

wedge and its free-body diagram are shown in Figure 3-17. The angle of wall
friction and the shear force between vertical wedge boundaries are assumed to
be zero. The inclination of the slip surface a is that which minimizes the
earth force. Calculation of a is discussed in paragraph 3-13d(2). If force
equilibrium is satisfied, the forces on the wedge form a closed force polygon
as shown in Figure 3-17. The equation for the horizontal effective earth
force P exerted by a resisting-side wedge on a wall or an adjacent wedge
IS :
(W + V)(l + tan A. cot a) tan a U tan A. - c,L

d
p a a
EE 1 - tan A, tan a cos a (1 - tan A, tan a)
+
"\ \ ' pw [3 33]
"
where the terms are the same as for the driving-side wedge equation (Equa-
tion 3-23) . Equation 3-33 is derived for failure occurring from left to
right. All values are positive in the directions indicated in Figure 3-17.
(2) Critical Value of Slip-Plane Angle.
(a) For a resisting-side wedge with a horizontal top surface, a can be

computed as follows:
a = 45° - ^ [3-34]
(b) The critical angle a for a resisting-side wedge with a planar (flat
or inclined) top surface, with no surcharge or with a strip surcharge V , is
given by the equation:
-c1 + <£? + 4c2

tan [3-35]
3-35
EM 1110-2-2502
29 Sep 89
a. Estimation of forces using slices
EEC4-5)
r
EE<3-4>
The force on the resisting

side of the structural
wedge is equal and
opposite to PEE(3-4) - The
force PEE added by the wedge
is ( PEE<3-4> - PEEM_5? La.
and acts to the left.
The force Pw Is equal to
PWR - PWL and acts to the left.
b. Free-body diagram of slice 4
v*
tf if PEE(3-4) WL
r
EEC4-5) WR
c. Force polygon for slice 4

Figure 3-17. Wedge method for resisting-side wedge
3-36
EM 1110-2-2502
29 Sep 89
For a resisting-side wedge, the equations for c and c are
„ 4cj (tan $, - tan 6) 4V tan 0(1 + tan 4,)

2«-«*4—J £ L, i>
Ä
«i ä '3"3«
2cd(l + tan *d tan B) 2V tan2 s(l + tan2^]

tan ^(1 + tan 4, tan B) + tan B +
Yh Yh
2
c2 _ [3_37]
2c (1 + tan A, tan ß) 2V[1 + tan $ )

A - tan $d + —2 —2 + -J> - U [3-38]
yh
(3) Surcharges. The comments regarding surcharges in paragraph 3-13c(5)

relative to analysis of driving-side wedges also apply in general to
resisting-side wedges. However, surcharges on resisting-side wedges tend to
enhance stability and therefore it is conservative to neglect them in
analysis. If resisting-side surcharges are not neglected, it must be assured
that the surcharge loading will be in place for the condition analyzed.
(4) Pressure Coefficients. Earth pressures for the resisting side may be
calculated as equivalent fluid pressures in a manner similar to that for the
driving side. See paragraph 3-13c(6) and Appendix H for further discussion.
3-14. Earth Pressure Calculations Including Wall Friction.
a. Driving Side. Friction between the backfill and wall, or on a plane

within the backfill, of up to one-half of the internal friction angle
(unfactored) of the backfill material may be used in the design.
b. Resisting Side. When wall friction is included in the analysis,

assuming the slip surface to be a log-spiral or other curved surface provides
lower and more reasonable values for the passive force and passive pressure
coefficient K (see Figure 3-11). Although the angle of wall friction
should generally be taken as zero, it may be assumed greater than zero where
movement and settlement of the wall are expected and permissible. Figure 3-18
provides earth pressure coefficients for horizontal backfills based on the
work of Caquot and Kerisel (1948) and Shields and Tolunay (1973) .
3-37
EM 1110-2-2502
29 Sep 89
0 5 10 15 20 25 30 35 40 45
Angle of Friction, 5 .degrees
Figure 3-18. Passive earth pressure coefficients
3-15. Distribution of Horizontal Earth Pressure.
a. Superposition of Pressures. The distribution of total horizontal

pressure on the driving or resisting side is obtained by superposing the
distributions due to horizontal effective earth pressure, water, and sur-
charges. Where compaction efforts are specified, horizontal earth pressures
should be calculated in accordance with paragraph 3-17.
b. Soils Completely Above or Completely Below the Water Table. The

effective earth pressure may be assumed to have a triangular distribution when
all of the following conditions hold:
(1) The wall will not move or it will rotate about the base.
3-38
EM 1110-2-2502
29 Sep 89
(2) The water table is at or below the base of the wall or at or above
the top of the wall (submerged soil).
(3) Water conditions are hydrostatic (no seepage).
(4) There is only one soil material.
(5) There is no cohesion (c = 0).
(6) The backfill surface is plane (it may be inclined).
The distribution is given by:
p^ = Ky'z [3-39]
where
K = K on the driving side. K for the resisting side could vary

between K and K or could be taken as zero
p o
y = the effective unit weight (total, saturated or moist unit weight if
above the water table, buoyant or submerged unit weight if below the
water table)
z = vertical distance measured down from the backfill surface
See Figure 3-19 for an example.
c. Partly Submerged Soils. Where the water table occurs between the top
and the base of the wall, and only one soil is present, the top portion of the
pressure diagram is a triangle given by Equation 3-39 and the bottom is a
trapezoid given by:
p'
r = K[Y z + Y' (z - z )] [3-40]
hz ' w w
where
z = depth to water table

w
Y' = (Y - Y ) below the water table
' ' 'w
An example is shown in Figure 3-20. See Appendix H where water table and
backfill surface are not parallel.
3-39
EM 1110-2-2502
29 Sep 89
P H soil PH TOTAL = 2f Z
-w
+
P H soil water PH TOTAL
=
H Pv + P water
= *. z« + X*
Pv = Pv - Pwatar
= 2f„ Zw + Xz -^w(zw +z)
= (Jf- *W)Z
= *Z
P' = K *'z
Figure 3-19. Lateral pressures, one soil completely above water
table or completely below water table
3-40
EM 1110-2-2502
29 Sep 89
M
u
a)
.c
u
M
3
a CD
o
L a)
W
0 ■u
£
O
L
3 •S
Q «)
CD
4- Et
IS
o
^q
0)
+ w
CO
CO
5 p<
%. cd
o
N CM
I
IB» 1» CO
<u
u
a
00
N •H
En
3-41
EM 1110-2-2502
29 Sep 89
d. Layered Soils. Where layered soils are present, the pressure diagram
is a triangle underlain by a series of trapezoids given by:
p'
r - K.(p». + Y'.zJ [3-41]
hz i rvx 'i i
where
K, = horizontal earth pressure coefficient for the i layer
p', = vertical effective earth pressure at the top of the i layer

vi
y' = effective unit weight of the i layer
z. = vertical distance measured down from the top of the i layer
An example is shown in Figure 3-21.
e. Irregular Backfills. Where the backfill is irregular, the pressure

diagram may be estimated by performing successive wedge analyses at incre-
mental depths from the top of the wall and applying the force difference from
successive analyses over the corresponding vertical area increment
(Agostinelli et al. 1981). Since this procedure is approximate, increasing
the number of calculation points does not necessarily increase accuracy. An
example of this procedure is shown in Figure 3-22. The pressure diagram may
also be estimated by the use of pressure coefficients (see para-
graphs 3-13c(6)) as shown in examples 7, 8, and 9 of Appendix M.
f. Cohesion Effects.
(1) Where the backfill is horizontal and where cohesion is present, its
theoretical effect is to reduce the driving side earth pressure by 2c /K
for the entire depth of the soil layer (see Equation 3-18). This infers
tension in the soil to a "crack depth" d where
2c,
d - — [3-42]
c
»^7
Consequently there is zero load on the wall in this region. For sloping back-
fills, see Appendixes H and I. Where cohesion is present, a water-filled ten-
sion crack should be considered in the inferred tension zone. The maximum
crack depth using the unfactored c value should also be checked. Where the
horizontal earth force is calculated from a pressure diagram that includes
negative pressure, the force reduction due to the inferred negative pressure
zone should be taken as zero. The pressure on the driving side should be
3-42
EM 1110-2-2502
29 Sep 89
©
4-
O
u
+ <P
CO
CO
4) iH
i_
a •H
O
roü
CO
0)
L 0)
3 h
CO
O CO
(0 0)
t-l
- X 3
CO
CO
«
u
p.
cct
cu
4-1
cd
N
CM
cu
3
60
•H
1*1
X"
CM
XCM
1 X'n
M
X
3-43
EM 1110-2-2502
29 Sep 89
©
L.
D
CO
v» (ft c
s. <D o
<F \ L. +-
v. a D
a.
\v o r> o
cä
a? \ +- .a
o CO
u
ft v < X) «d
r-H
3>
a)
a>
13
N N N N N co G
o
CO
a
_ -gz-^ "Z^Z ~^\ ^N "■ nc
4-1
n
CD
o>
 m
E n
o
1
a> Q. QT es
CM
o I
i_ i N ' N en
o
4- Q^ or <u
II ii S,
a. CT a~
3-44
EM 1110-2-2502
29 Sep 89
computed using Equation 3-18 by setting the 2nd term equal to 0 and K equal
to K and using the pressure distribution as shown in Figure 3-23.
(2) For the resisting side, passive pressure theory indicates no tension
crack will form and the pressure would be calculated using Equation 3-22. The
pressure distribution for a cohesive soil on the resisting side of a structure
is shown in Figure 3-24. However, for operating conditions without movement,
a tension crack may form due to moisture loss reducing or eliminating the re-
sisting side pressure. See paragraph 3-8 for resisting pressure to be used
for design.
(3) Refer to guidance on use of cohesive materials in paragraph 3-5.
g. Wall Movement Effects.
(1) Where the expected mode of wall movement is translation and/or rota-
tion about a point other than the base (such as for braced walls) the value of
K varies with depth and the horizontal earth pressure distribution will be
parabolic rather than triangular. Solution methods for such conditions are
less reliable than those for rotation about the base. Available methods in-
clude Rendulic's procedure (Winterkorn and Fang 1975), Dubrova's procedure
(Harr 1977), and a procedure given by Wu (1966).
(2) Where the expected mode of wall movement is translation and/or

rotation about a point other than the base, the force may be assumed the same
as that obtained for rotation about the base, but the point of application
should be taken at 45 percent of the wall height above the base.
3-16. Surcharge Effects.
a. Uniform Surcharges. Where uniform surcharges (q) are present, the

vertical effective stress increases by the amount of the surcharge and the
horizontal earth pressure diagram is a trapezoid given by:
p K(q + Y z)
hz " ' £3~43]
An example is shown in Figure 3-21.
b. Finite Surcharges.
(1) Pressure Increase Due to Finite Surcharges. The distribution of the

horizontal pressure increase due to finite surcharges should be calculated
using experimentally modified elastic theory where expected (or allowable)
strains due to the surcharge are small. Pressures due to point and line loads
can be calculated using Figures 3-25 and 3-26, respectively. The resulting
pressures are about twice as great as would be obtained from either unadjusted
elastic solutions or limit-equilibrium solutions. This difference is due to
wall rigidity not considered in elastic or limit-equilibrium methods. Pres-
sures due to strip loads can be calculated using Figure 3-27. Pressures due
3-45
EM 1110-2-2502
29 Sep 89
l_
O
+•
^J o
s
o.
o
•H
v
O
u
Tl
o
(0
a)
L 0)
as
+■ u
o
a>
15*J
o u
w til
c
o
o n-l
4J
x
to
II
N
X M
3
a
to
cd
U

nj
m
CM
I
CO
<u
1-1
00
1-1
3-46
EM 1110-2-2502
29 Sep 89
r. *. c
r*—'
r* i
r* '
<3 1
KP rH
2cVKp
PpH = KpY'z + 2c VK7

Figure 3-24. Lateral pressure distribution; passive case,
soil with cohesion
to strip surcharge loads of more general shapes can be calculated by applying

the principle of superposition to these solutions; a pressure-intensity curve
of any shape can be modeled to any desired degree of accuracy as the sum of
point, line, or strip loads. Example computations involving surcharges are
shown in examples 4 and 10 of Appendix M.
(2) Force Due to Finite Surcharges. Point, line, or nonuniform (finite)

surcharge loads are supported by distribution or "diffusion" of stresses
within the backfill material. These result in a curved pressure diagram; the
point of application for the horizontal force resultant due to point or line
loads is given in Figure 3-28. Where surcharge pressure distributions of a
general shape have been modeled by superposition of these basic solutions, the
point of application is found by dividing the total moment due to the sur-
charge resultants by the sum of the surcharge resultants. Where surcharge
loadings are included in a wedge-method analysis, the difference in resultant
force due to the surcharge (AP ) should be applied at a different point on the
H
wall from the resultant due to backfill weight. An approximate method for
locating the line of action for a line load (Terzaghi 1943) is shown in Fig-
ure 3-29. An example using this approximate method is shown in example 4 of
Appendix M.
3-17. Earth Pressures Due to Compaction. The use of heavy rollers for com-
paction adjacent to walls can induce high residual pressures against the wall.
Although a reasonable degree of compaction is necessary to provide adequate
shear strength and minimize settlement, excess backfill compaction should be
avoided. Ingold (1979a,b) proposed a procedure for estimating lateral pres-
sures due to compaction that has been modified herein (Appendix J) to account
3-47
EM 1110-2-2502
29 Sep 89
Point Load
V
SECTION PLAN
(below)
Increase in horizontal pressure, APHz , on a

section through point load, V
2K2
'
■or a > 0.4
for a < 0.4
Increase In horizontal pressure, ApHx ^ at

distance X from plane of load, V
a = tan"
(4)
'HX =" AP
APHY "KH7
HZ cos2 (l.la)
Figure 3-25. Increase in pressure due to point load (after Spangler 1956)
3-48
EM 1110-2-2502
29 Sep 89
Line Load
ah V per unit length
z= bh _x
APÜ2.
r
Increase In horizontal pressure, APH2, at
depth bH due to line load, V/f t
at distance aH from wall.
2
/4VV
APHZ= /j4V_V ac2b \ for a > 0.4
2 2 2
WhAta + b ) J
Ap„z= p_V 0-203 b \ for a < 0.4

2 2
\ h J\ (0.16 + b ) /
Figure 3-26. Increase in pressure due to line load (after Spangler 1956)
3-49
EM 1110-2-2502
29 Sep 89
(x2- X,)
for non-yielding walls:

APHZ= 2_% (j8- sinjS cos2a)
for yielding walls,

(walls at failure):
APHZ= % (j8- slnjS cos2oc)
IT
ß in radians
/Utan'^Vtan'^
1
-^(Hr
2z )
Figure 3-27. Increase in pressure due to strip load
3-50
EM 1110-2-2502
29 Sep 89
Point Load, V
a APH
0.4 0.78 (V/h) .59 h
0.5 0.60 (V/h) .54 h
0.6 0.46 (V/h) .48 h
Line Load.V/ft
for a 10.4 APH = 0.55 V
for a > 0.4 APH = 0X4V

(a2 + I )
0.4 0.60 h
0.5 0.56 h
0.6 0.52 h
0.7 0.48 h
Figure 3-28. Resultant forces, point and line

loads (after Spangler 1956)
3-51
EM 1110-2-2502
29 Sep 89
a'c'll bd
b'c" II be
be is failure surface
without surcharge
(a1 from horizontal)
'x i be is failure surface

&'s''\+ without surcharge
1' L a" Is critical slip
angle with surcharge
if a'= a\AP= 0
APH= P (XV)- P (Y>

Figure 3-29. Approximate line of action for
line loads (Terzaghi 1943)
3-52
EM 1110-2-2502
29 Sep 89
for walls designed for at-rest conditions. The roller is assumed to exert a
line load of P lb/ft obtained from the roller weight and drum dimensions;
double this value is recommended for vibratory rollers. The design pressure
diagram (Figure 3-30) is composed of three linear segments:
a. Starting at the top of the wall, the pressure increases linearly to a

value of p/ at a depth
r z . In this region, the horizontal stress is
hm cr
increased during compaction due to the roller pressure but then the horizontal
stress is reduced by passive failure when the roller is removed.
b. The horizontal pressure is constant with depth from z to z and

is compaction induced.
c. At depth z , the compaction-induced pressure equals the horizontal

pressure due to soil weight (at-rest pressure). The pressure increases
linearly below this depth according to the equations in paragraph 3-15.
Compaction-induced pressures need only be considered for structural design.

For overturning, bearing, and sliding analyses, any wall movement due to
compaction-induced pressures would be accompanied by a reduction in the pres-
sure. As shown by the calculations in Appendix J, horizontal pressures due to
compaction may exceed the at-rest pressure in only the upper few feet unless
roller loads are particularly high. The effects of compaction are shown in
example 1 of Appendix M.
Section III. Water Pressures
3-18. Pressure Calculations. In all cases, water pressures at a point may be

calculated by multiplying the pressure head at the point by the unit weight of
water (62.4 lb/cu ft). As water has no shear strength, water pressures are
equal in all directions (K = 1.0). The pressure head is equal to the total
head minus the elevation head. The pressure head at a point is the height
water would rise in a piezometer placed at the point. The elevation head is
the height of the point itself above an arbitrary datum. Water pressures must
be added to effective earth pressures to obtain total pressures.
a. Static Pressures. For static water (no seepage) above or below the
ground surface, the total head is constant and the pressure head at any point
is the difference in elevation between the water surface and the point.
b. Water Pressures with Earth Pressure Equations. Where Coulomb or

at-rest equations are used to calculate the driving-side earth pressures for a
totally submerged soil mass, the buoyant soil weight (y = y - Y ) is used
in the earth pressure equations and the calculated effective earth pressures
are added to the calculated water pressures.
c. Water Forces with Wedge Analysis. The wedge method (Equations 3-23
and 3-33) uses total densities, uplift forces, and horizontal water forces on
3-53
EM 1110-2-2502
29 Sep 89
Earth Pressure
-^»- p
«a X-
P" =Kpr'z
hm
p =
hm KATT
«-
Depth from
top of fill m-
rtjg"
*ty
p' =K0y*z
hm
2KAK0P 2
2P
cr 7T y 2 =
KAKOTTT"
P is roller line load, lb/ft ( use twice roller

weight for vibratory rollers )
Figure 3-30. Design pressure envelope for nonyielding walls with
compaction effects
3-54
EM 1110-2-2502
29 Sep 89
the vertical sides of the wedge. Consequently, it gives the effective earth
force, and water forces must be added to obtain total forces (see example 3 in
Appendix M).
d. Water Pressures Where Seepage is Present. Where seepage occurs, the

pressure head at points of interest must be obtained from a seepage analysis.
Such an analysis must consider the types of foundation and backfill materials,
their possible range of horizontal and vertical permeabilities, and the effec-
tiveness of drains. Techniques of seepage analysis are discussed in EM 1110-
2-1901, Casagrande (1937), Cedergren (1967), Harr (1962), and other refer-
ences. Techniques applicable to wall design include flow nets and numerical
methods such as the finite element method and the method of fragments. An
example of pressure calculations using a flow net is shown in Figure 3-31.
Where soil conditions adjacent to and below a wall can be assumed homogeneous
(or can be mathematically transformed into equivalent homogeneous conditions)
simplified methods such as the line-of-creep method may be used. Simplified
methods are advantageous for preliminary studies to size wall elements or com-
pare alternate wall designs; however, designers should ensure that the final
design incorporates water pressures based on appropriate consideration of
actual soil conditions.
3-19. Seepage Analysis by Line-of-Creep Method. Where soil conditions can be

assumed homogeneous, the line-of-creep (or line-of-seepage) method provides a
reasonable approximate method for estimating uplift pressures that is partic-
ularly useful for preliminary or comparative designs. The line of creep may
underestimate uplift pressures on the base and thus be unconservative. There-
fore, final design should be based on a more rigorous analysis. The method is
illustrated in Figure 3-32. The total heads at the ends of the base (points B
and C) are estimated by assuming that the total head varies linearly along the
shortest possible seepage path (A'BCD'). Once the total head at B and C is
known, the uplift pressures U and U are calculated by subtracting the
B C
elevation head from the total head at each point and multiplying the resulting
pressure head by the unit weight of water. The total uplift diagram along the
failure surface is completed in a similar manner. Where a key is present
(Figure 3-33), point B is at the bottom of the key and line segment BC is
drawn diagonally. Examples using the line-of-creep method are contained in
Appendix N.
3-20. Seepage Analysis by Method of Fragments. Another approximate method

applicable to homogeneous soil conditions is the method of fragments. It is
more accurate than the line-of-creep method. The soil is divided into a
number of regions or fragments for which exact solutions of the seepage con-
ditions exist. The head loss through each fragment is calculated by mathe-
matically combining the assemblage of fragments. The method assumes that
fragment boundaries are equipotential lines (contours of equal total head) and
provides an exact solution where this assumption is true (I-walls and single
sheet piles). Details of the method and instructions for the computer program
CFRAG (Appendix O) are presented by Pace, et al. (1984). Further background
on the method is presented by Harr (1962, 1977) . Keyed bases should be
modeled by treating the key as a sheet pile and the soil below the base as a
3-55
EM 1110-2-2502
29 Sep 89
Headwater Side Taflwater Side
EL.5I0
"M» ///mm
Impervious
Pt. A Total Heads 510

Elevation Head: 510
Pressure Heads 0
Pressures 0
Pt. B Total Head: 510 - (2/6 K5I0 - 507 )= 509

507 + ( 4/6)( 3 ) = 509
Elevation Head: 501
Pressure Head: 509 - 501 = 8'
Pressure: ( 8 )( 62.4 ) = 499.2 lb/tt2

Figure 3-31. Water pressures from flow net
3-56
EM 1110-2-2502
29 Sep 89
Headwater Side Tallwater Side
EL.5I0
EL.=
Datum ö 0.0
Length of Shortest Seepage Path: A'BCD'
(A') Total Head at A': 510 ft.
Elevation Head at A': 510 ft.
Pressure Head at A': 0 ft.
(B ) Total Head at B: 510 - (A'B ) (510 - 507 )

( A'BCD')
Elevation Head at B: 501
Pressure Head at B = Total Head - Elevation Head
(C ) Total Head at C: 510 - (A'BC ) (510 - 507 )

( A'BCD')
Elevation Head at C: 501
etc.
Water Pressure: Pw = "Y^ • ( Pressure Head
Figure 3-32. Water pressure by line-of-creep method
3-57
EM 1110-2-2502
29 Sep 89
Figure 3-33. Seepage path for line of creep
type IV. Accuracy is improved by minimizing the number of fragments, not by

maximizing them to incorporate minor changes in geometry. Where water pres-
sure on the base of a wall is calculated by the method of fragments, the water
pressure along the driving-side and resisting-side wedge bases may be taken to
vary linearly as described in the preceding paragraph.
3-21. Seepage Analysis by the Finite Element Method. The finite element
method provides a powerful tool to solve confined or unconfined seepage prob-
lems involving multiple soils with isotropic or anisotropic permeabilities.
It is particularly useful for evaluating the effect of drains and analyzing
walls with complicated foundation and backfill geometry. The WES computer
program for the finite element method is described by Tracy (1983). Pre- and
post-processors for the program are also available (Tracy 1977a, 1977b).
3-22. Uplift Calculations for Rock Foundations. Seepage beneath flood walls
3-58
EM 1110-2-2502
29 Sep 89
founded on competent rock typically occurs in joints and fractures, not uni-
formly through pores as assumed for soils. Consequently, the assumptions of
isotropy and homogeneity and the use of two-dimensional analysis models com-
monly employed for soil foundations will generally be invalid. Total head,
uplift pressure, and seepage quantities may be highly dependent on the type,
size, orientation, and continuity of joints and fractures in the rock and the
type and degree of treatment afforded the rock foundation during construction.
Since any joints or fractures in the rock can be detrimental to underseepage
control, the joints and fractures should be cleaned out and filled with grout
before the concrete is placed, as discussed in paragraph 7-4g. For walls on a
rock foundation, the total seepage path can be assumed to be the length of the
base which is in compression. An example of a wall on a rock foundation is
shown in example 2 of Appendix N.
3-23. Effect of Drains. Water pressures for design analyses should consider
both working drains and blocked drainage conditions. Achieving an adequate
factor of safety for an analysis considering blocked drainage is usually not
good justification for omitting drains. Preferred practice is to provide
drains; lower factors of safety than specified herein may be justified where
blocked drainage assumptions are combined with rare and/or conservative load-
ing assumptions. All such deviations from recommended safety factors should
be supported by an assessment of expected drain reliability, and a justifica-
tion that the factor of safety is reasonable in light of the analyzed
conditions. Drains are discussed further in paragraphs 6-6 and 7-4.
3-24. Surge and Wave Loads.
a. General Criteria. Wave and water level predictions for the analysis
of walls should be determined with the criteria presented in the Shore Protec-
tion Manual (U. S. Army Engineer Waterways Experiment Station 1984). Design
forces acting on the wall should be determined for the water levels and waves
predicted for the most severe fetch and the effects of shoaling, refraction,
and diffraction. A distinction is made between the action of nonbreaking,
breaking, and broken waves, where the methods recommended for calculation of
wave forces are for vertical walls. Wave forces on other types of walls
(i.e., sloping, stepped, curved, etc.) are not sufficiently understood to rec-
ommend general analytical design criteria. In any event, a coastal engineer
should be involved in establishing wave forces for the design of important
structures.
b. Wave Heights. Wave heights for design are obtained from the statis-
tical distribution of all waves in a wave train, and are defined as follows:
H = average of the highest one-third of all waves
H = 1.67 H = average of highest 1 percent of all waves
H = height of wave which breaks in water depth d,
c. Nonbreaking Wave Condition. When the depth of water is such that
3-59
EM 1110-2-2502
29 Sep 89
waves do not break, a nonbreaking condition exists. This occurs when the wa-
ter depth at the wall is greater than approximately 1.5 times the maximum
wave height. The H wave shall be used for the nonbreaking condition.
Design nonbreaking wave pressures shall be computed using the Miche-Rudgren
Method, as described in Chapter 7 of the Shore Protection Manual (U. S. Army-
Engineer Waterways Experiment Station 1984). Whenever the maximum stillwater
level results in a nonbreaking condition, lower stillwater levels should be
investigated for the possibility that shallow water may produce breaking wave
forces which are larger than the nonbreaking forces.
d. Breaking Wave Condition. The breaking condition occurs when the

steepness of the wave and the bottom slope on the front of the wall have cer-
tain relationships to each other. It is commonly assumed that a structure
positioned in a water depth d will be subject to the breaking wave condi-
tion if d < 1.3 H where H is the design wave height. Study of the break-
ing process indicates that this assumption is not always valid. The height of
the breaking wave and its breaking point are difficult to determine, but
breaker height can be equal to the water depth of the structure, depending on
bottom slope and wave period. Detailed determination of breaker heights and
distances for a sloping approach grade in front of the wall are given in the
Shore Protection Manual (U. S. Army Engineer Waterways Experiment Station
1984) . Special consideration must be given to a situation where the fetch
shoals abruptly (as with a bulkhead wall submerged by a surge tide) near the
wall, but at a distance more than an approximate 0.7 wavelength away from the
wall, and then maintains a constant water depth from that point to the wall.
In this case waves larger than the water depth can be expected to have broken
at the abrupt shoaling point, leaving smaller, higher frequency waves to reach
the wall. Design breaking wave pressure should be determined by the Minikin
method presented in Chapter 7 of the Shore Protection Manual (U. S. Army Engi-
neer Waterways Experiment Station 1984). Breaking wave impact pressures occur
at the instant the vertical force of the wave hits the wall and only when a
plunging wave entraps a cushion of air against the wall. Because of this de-
pendence on curve geometry, high impact pressures are infrequent against
prototype structures; however, they must be recognized and considered in
design. Also, since the high impact pressures caused by breaking waves are of
high frequency, their importance in design against sliding and overturning may
be questionable relative to longer lasting lower dynamic forces. An example
involving a breaking wave condition is shown in example 7 of Appendix N.
e. Broken Wave Condition. Broken waves are those that break before
reaching the wall but near enough to have retained some of the forward momen-
tum of breaking. The design breaker height in this case (H, ) is the highest
wave that will be broken in the break zone. Design wave forces for the height
H should be determined by the method presented in Chapter 7 of the Shore
Protection Manual (U. S. Army Engineer Waterways Experiment Station 1984).
f. Seepage Pressures. Seepage pressures are based on the elevation of

the surge stillwater level (paragraph 4-5).
3-60
EM 1110-2-2502
29 Sep 89
Section IV. Supplemental Forces
3-25. Wind Load. Wind loads should be considered for retaining and flood
walls during construction, prior to placing backfill. Wind loads can act any-
time in the life of a flood wall. In locations subjected to hurricanes, a
wind load of 50 lb/sq ft can be used conservatively for walls 20 feet or less
in height for winds up to 100 miles per hour (mph). In locations not sub-
jected to hurricanes, 30 lb/sq ft can be used conservatively for the same
height of wall and wind velocity conditions. For more severe conditions, the
wind loads should be computed in accordance with ANSI A58.1 using a coeffi-
cient C equal to 1.2.
3-26. Earthquake Forces.
a. General. For retaining walls which are able to yield laterally during
an earthquake, the calculation of increased earth pressures induced by
earthquakes can be approximated by the Mononobe-Okabe pseudo-static approach
outlined below. In addition, the inertial forces of the wall, plus that
portion of the adjacent earth and/or water which is assumed to act with the
wall, should be included.
b. Mononobe-Okabe Analysis. This analysis is an extension of the Coulomb

sliding-wedge theory taking into account horizontal and vertical inertial
forces acting on the soil. The analysis is described in detail by Seed and
Whitman (1970) and Whitman and Liao (1985).
(1) Assumptions. The following assumptions are made by the

Mononobe-Okabe analysis:
(a) The wall is free to yield sufficiently to enable full soil strength
or active pressure conditions to be mobilized.
(b) The backfill is completely above or completely below the water table,
unless the top surface is horizontal, in which case the backfill can be parti-
ally saturated.
(c) The backfill is cohesionless.
(d) The top surface is planar (not irregular or broken).
(e) Any surcharge is uniform and covers the entire surface of the soil
wedge.
(f) Liquefaction is not a problem.
(2) Equations. Equilibrium considerations of the soil wedge on the

driving and resisting sides lead to the following Mononobe-Okabe equations for
computing the active and passive forces exerted by the soil on the wall when
the soil mass is at the point of failure (total shear resistance mobilized)
along the slip plane of the Mononobe-Okabe wedge shown in Figure 3-34:
3-61
EM 1110-2-2502
29 Sep 89
For driving (active) wedges (Figure 3-34a),
P*E = \ KAEY(1 - kv)h2 [3-44]
cos2 (<() -T - 0)
K.C. =
[3-45]
2 sin (if + 8) sin (<|) - Y - ß)
cos V cos 9 cos OF + 0 + 8) 1 +
cos (ß - ö) cos(T + « + ö)
For resisting (passive) wedges (Figure 3-34b),
PPE = \ KPEY(1 " kv)h2 [3-46]
cos2 ($-*¥+ Q)
[3-47]
sin (<|> + 8) sin (<|> - »F + ß)
cos ¥ cos2 6 cos OF - 6 + 8)
cos (ß - Ü) cos (4» - Ö + 6)
P_„ and P are the combined static and dynamic forces due to the driving
J
AE PE
and resisting wedges, respectively. The equations are subject to the same
limitations that are applicable to Coulomb's equations. Definitions of terms
are as follows:
Y = unit weight of soil
k = vertical acceleration in g's

v
h = height of wall
(j> = internal friction angle of soil

/ \
¥ = tan seismic inertia angle
T-^T;
horizontal acceleration in g's
h
0 = inclination of wall with respect to vertical (this definition of 0
is different from 0 in Coulomb's equations)
8 = wall friction angle
ß = inclination of soil surface (upward slopes away from the wall are
positive)
3-62
EM 1110-2-2502
29 Sep 89
Slip plane
y = tan"1 -^
I- k
W(l-kv)
a. Mononobe-Okabe (active) wedge
Slip plane
b. Passive wedge
Figure 3-34. Driving and resisting seismic wedges, no saturation
3-63
EM 1110-2-2502
29 Sep 89
(3) Simplifying Conditions. For the usual case where k , 8 , and 6

are taken to be zero, the equations reduce to:
KAE
cosMi-J) [3-48]
r12
cos2 Y 1 + ^S 4> cossin ß (<t>cos- YY - ß)
cos^ (♦ - Y) [3-49]
Si
-Vs
sin «)) sin (d> - Y + ß)
cos2 Y cos ß cos Y
¥ = tan (k
h)
and
P = 1/2 K^yh
AE
P = 1/2 KpEYh
PE
For the case when the water table is above the backfill, PAE and PpE must
be divided into static and dynamic components for computing the lateral
forces. Buoyant soil weight is used for computing the static component below
the water table, with the hydrostatic force added, and saturated soil weight
is used for computing the dynamic component (see paragraph 3-26c(3)).
(4) Observations. General observations from using Mononobe-Okabe

analysis are as follows:
(a) As the seismic inertia angle *P increases, the values of KAß and
K approach each other and, for a vertical backfill face (0=0), become
PE
equal when *¥ = ty .
(b) The locations of P

and P are not given by the Mononobe-Okabe
AE PE
analysis. Seed and Whitman (1970) suggest that the dynamic component APAE
be placed at the upper one-third point, AP being the difference between
AE
P and the total active force from Coulomb's active wedge without the earth-
AE
quake. The general wedge earthquake analysis described in paragraph 3-26c
places the dynamic component AP at the upper one-third point also, but
AE
computes AP as being the difference between P and the total active
AE Ail
3-64
EM 1110-2-2502
29 Sep 89
force from the Mononobe-Okabe wedge. The latter method for computing APAE ,
which uses the same wedge for computing the static and dynamic components of
P , is preferred.
(c) Another limitation of the Mononobe-Okabe equation is that the con-

tents of the radical in the equation must be positive for a real solution to
be possible, and for this it is necessary that <|> > *P + ß for the driving
wedges and <|> > *F - ß for the resisting wedges. This condition could also be
thought of as specifying a limit to the horizontal acceleration coefficient
that could be sustained by any structure in a given soil. The limiting condi-
tion for the driving wedge is:
1^ s (1 - kv) tan (* - ß) [3-50]
and for the resisting wedge:
k^ <; (1 - k ) tan ($ + ß) [3-51]
(d) Figure 3-35a (Applied Technology Council 1981) shows the effect on
the magnification factor F (equal to K /Ka) on changes in the vertical
X AD A
acceleration coefficient k . Positive values of k have a significant
v v
effect for values of k greater than 0.2. The effect is greater than
10 percent above and to the right of the dashed line. For values of k^ of
0.2 or less, k can be neglected for all practical purposes.
(e) K and F are also sensitive to variations in backfill slope,

Alii J-
particularly for higher values of horizontal acceleration. This effect is
shown in Figure 3-35b.
c. General Wedge Earthquake Analysis. When the Coulomb wedge assump-

tions cannot be met, the following wedge analysis can be used. The equations
for the dynamic force given below for various conditions are simply the hori-
zontal acceleration coefficient multiplied by the weight of the wedge defined
by the critical slip-plane angle. See example 11 of Appendix M for sample
calculations.
(1) Assumptions. The equations for determining the critical slip-plane

angle for driving and resisting wedges subjected to a horizontal acceleration
are developed with the following assumptions:
(a) The shear on the vertical face of the wedge is zero.
(b) The shear strength along the potential slip planes in the soil has
not been mobilized to any extent, i.e., for static loading prior to an
earthquake.
3-65
EM 1110-2-2502
29 Sep 89
4.0
ac
o
i—
o 3.0
.ox1
\ ;/y
Kh=<5 ./ _
<
U.
Z
O 2.0
t— 8=4>/2
<
U_ 1.0 — 0 =J8= 0
z
o <*> = 35°
< 1 i i i
2
°-c).2 -0. 0 0.1 0.2 0.3
VERTICAL SEISMIC COEFFICIENT kv
a. Influence of vertical seismic coefficient
on magnification factor
1-
4.0
cc
o
1—
o 3.0
<
u.
z 2.0
o
1—
B=<#>/2
<
o 0= kv= 0
u_ 1.0
z *= 35°
o
<
3= 0
0 5° 10° 15° 20°
SLOPE ANGLE ß
b. Influence of backfill slope angle on magnification factor
Figure 3-35. Influence of k and ß on magnification factor

(after Applied Technology Council 1981)
3-66
EM 1110-2-2502
29 Sep 89
(2) Equations for Cohesionless, Dry Backfill Above the Water Table.
Driving and resisting forces for cohesionless, dry, sloping planar-surfaced
backfill below the water table where k , 8 , and 0=0 can be computed as
follows:
(a) Static Components. The static components for a driving and resisting
wedge are:
2
PA - i Vh [3-52]
pp - \ vh2 [3 531
"
where
y. m A - tan ♦ cot a\ / tan a \ [3_54]

A \l + tan * tan a J 1 tan a - tan V>J
v «= /l + tan $ cot <x\ / tan a \ [3-55]

*¥ I 1 - tan <(> tan a) I tan a - tan &J
as derived in paragraph H-2 and H-3, Appendix H.
For an active wedge:
a = tan1
V—~ ^2. [3-56]
2 (tan <t> - K)
e
c 5- [3-57]
l 1 + 1»^ tan <f>
tan <t> (1 - tan <l> tan 3) - (tan 6 + 1^)

[3-58]
c
2 " tan * (1 + \ tan ♦)
For a passive wedge:
3-67
EM 1110-2-2502
29 Sep 89
a » tan
-1 [ - cl +
\C? + 4c„
[3-59]
2 (tan $ - k.)
: [3-60]
1 * 1 + k, tan (j)
tan <ji (1 + tan <f> tan g) + (tan ß - k^)

c = [3-61]
2 tan <\> (1 + k, tan ij>)
If k > 0 , replace y with (1 - k )y.
(b) Dynamic Components. The dynamic component for each wedge is:
Yh [3-62]
&P = AP =
AE PE \ 2 (tan a - tan 0)
(c) Total Driving Force. The total driving force is:
P P + ÄP [3-6JJ
AE * A AE
which is equal to:
P [3-64]
AE = I KAE^2
from the Mononobe-Okabe analysis.
The line of action for P,„ may

J be found as:
AE
AE
(!)-«(r) [3-65]
AE
It should be noted that for large values of k , which cause a to be small,
3-68
EM 1110-2-2502
29 Sep 89
P can be negative causing the line of action of P to lie above the upper
third point.
(d) Total Resisting Force. The total resisting force is:
p = p _ Ap [3-66]
PE P PE
which is equal to:
? = K [3-67]
PE 2 PEYh
from the Mononobe-Okabe analysis.
The line of action for P„ may be found as:

PE
(l)-^PE(f) [3-68]
PE P
PE
(3) Equations for Cohesionless Backfill with Water Table. Driving and
resisting forces for cohesionless, sloping, planar-surfaced backfill with
water table where k , 8 , and 0=0 can be computed as follows:
(a) Driving Force. The static components for a driving wedge are (see
Figures 3-36a and 3-37a):
P = P + P
A A1 A2 " 1 V(h " V2 + I hs [2V<h - V + Ws] [3 69]
"
P =|Yh2 [3-70]
ws 2 w s
and the dynamic components are (see Figures 3-36a and 3-37a)
Yti «s ~ Y) hs [3-71]
&P AP + AP =
AE - AE1 AE2 \ 2(tan a - tan ß) 2 tan a
3-69
EM 1110-2-2502
29 Sep 89
Slip plane
a. Driving wedge
Slip plane
b. Resisting wedge
Figure 3-36. Seismic wedges, water table within wedge
3-70
EM 1110-2-2502
29 Sep 89
a. Driving wedge
b. Resisting wedge
Figure 3-37. Static and dynamic pressure diagrams, water table

within wedge
3-71
EM 1110-2-2502
29 Sep 89
giving a total force of:
P, = P. + P + AP [3-72]
AE A ws AE
where
Y = saturated unit weight of fill
Y = moist unit weight of fill
y = buoyant unit weight of fill
Y = unit weight of water
K = /1 ~ tan 4> cot a u tan g

A
\ l + tan <|> tan a j\ tan a - tan ß
1 - tan <j) cot a l +|_ tan g

„ - i|JL
1 + tan <|> tan a )-( tan a - tan ß
and a is defined in Equation 3-56.
(b) Resisting Force. The static components for the resisting wedge are
(see Figures 3-36b and 3-37b):
P
P " PP1 + P
P2 " 1 V(h " V2 +
1 \ [2V(h " hs) +
Vbhs] [3 73]
"
2
Pws =hh
2 w s
[3-74]
and the dynamic components are:
+ 3 C3 75]
AP
PE
= AP
r
PEl
+ AP
PE2
s» fc .
t Yh"
Ti | 2 (tan a - tan B) J \[l IT. ] "
Pr = P + P - AP [3-76]
PE P ws PE
3-72
EM 1110-2-2502
29 Sep 89
where y , y. , y , and y are defined in paragraph 3-26c(3) (a),
and
(1 + tan d) cot a] ( tan a J [3-77]

\1 - tan $ tan a/ Vtan a - tan &/
(1 + tan 4> cot a) - 1^ [3-78]

h 1 - tan <[> tan a/ tan a - tan 6
and the equations for a are given in Equation 3-59.
(4) Equations for Cohesive Backfill with Water Table. Driving and re-
sisting forces for a cohesive, sloping, planar-surfaced backfill with water
table where k , 8 , and 6=0 can be computed as follows:
(a) Driving Force. The static components for the driving wedge are (see
Figure 3-38a):
P
A " PA1 + PA2 - I V0 - <V " hsJ
+ |h>[2KAY(h-dc-hg)+Vbh.] t7 791
'
PwS = 1 u2 [7-80]
2 Vs
and the dynamic components are (see Figure 3-38a)
&P
AE = AP
AE1 + &P
AE2 " \
(liA
2 (tan a - tan 6) \
2 2
(Ys - Y) hs
2 tan a
[3-81]
[3-82]
AE A ws AE
3-73
EM 1110-2-2502
29 Sep 89
where
Y = moist unit weight of fill
y = buoyant unit weight of fill
Y = saturated unit weight of fill

's
Y = unit weight of water
'w
- ( * ~ tan ft cot a\( tan a

^ [3-83]
~ \1 + tan <f> tan a/\tan a - tan ft)
_ /l - tan <|> cot a\\ l + ( tan a A JL [3-84]

\ \l + tan <|> tan a/I \tan a - tan ß " /
c+
a = tan
-i i i V4 + 4c r
[3-85]
^ / j. i \ _L. Ac (tan <ji + tan g)

2 tan <(. (tan <(. - 1^) + Y(h + d )
c =
[3-86]
l
« , i x ^ 2c(l - tan j) tan ß)

tan <(i(l - tan $ tan ß) - (tan ß + 1^) + ~ + j ^
c =
[3-87]
2
, , 2c(l - tan <j> tan ß) [3-88]

A = (1 + T^ tan <|>) tan $ + Y(h + d )
d c = cos a (sin aC/Y- tan $ cos a) [3-89]
3-74
EM 1110-2-2502
29 Sep 89
Slip plane
a. Driving wedge
Slip plane
b. Resisting wedge
Figure 3-38. Static and dynamic pressure diagrams, cohesive fill,

water table within wedge
3-75
EM 1110-2-2502
29 Sep 89
(b) Resisting Force. The static components for the resisting wedge are
(Figure 3-38b):
P
P = P
P1 + P
P2 =
I V(h " hs)2 +
I hs[2V(h - V +
Vbhs] + 2K ch
c [3
" 90]
2
P
ws
-iyh
2 'w s
[3-91]
and the dynamic components are (see Figure 3-38b)
AP
PE = &P
PE1 + &P
PE2 K I j£
2 (tan a - tan 6) \ 2 tan a
[3-92]

p_„ = p_ + p + AP^^ [3-93]
PE P ws PE
where y , y , y , and y are defined in paragraph 3-26c(4)(a)
and
_ /l + tan (fr cot g\/ tan a \ [3-94]
P ~ \1 - tan $ tan a/\tan a - tan 6/
v. - (l + tap
♦ cot a
\ 11 + ( tan a
- i\ X.1 [3-95]
T) \1 - tan <|> tan a/ I \tan o - tan ß / y, I
a = tan
-1 ( ~C1 +
VC1 + 4C
2j [3-96]
2 tan « (tan ♦ - k„) + 4c (tan

♦ " tm ß)
[3-97]
A
3-76
EM 1110-2-2502
29 Sep 89
tan *(1 + tan * tan f» + (tan {? - t) + 2c(1 + ta

? ♦ tan ß)
c2 —3 3Ü [3-98]
A - (1 + ^ tan |) tan + + 2c(1 + ta

g ♦ tan
® [3-99]
K _ 1 g tan ot r. .-.,
c 2 sin a cos a (1 - tan $ cos a) tan a - tan 6 iJ-iuuj
d. Inertia Force of Wall. The inertia force of the wall, including that
portion of the backfill above the heel or toe of the wall and any water within
the backfill which is not included as part of the Coulomb wedge, is computed
by multiplying the selected acceleration coefficient by the weight of the wall
and backfill. This force is obtained by multiplying the mass by acceleration
as follows:
F - ma = ma (&\ - - w = k,W [3-101]
e. Hvdrodvnamic Force Due to Water Above Ground Level. Water standing

above ground can have its static pressure, acting against a wall, increased or
decreased due to seismic action. Figure 3-3 9 shows the pressures and forces
due to earthquakes for freestanding water. The dynamic force is given by
Westergaard's (1933) equation as:
P
E - (!) w2 [3 lü2]
-
where C is a factor depending upon the depth of water, h , in feet, and
the earthquake period of vibration, T , in seconds. Westergaard's approxi-
mate equation for C in kip-second-foot units is:
E
CE = °-051 [3-103]
yj 1 - 0.72 (h/1000T)2
3-77
EM 1110-2-2502
29 Sep 89
Water surface
Top of
ground
Figure 3-39. Hydrodynamic forces for freestanding water
Normally, for retaining and flood walls, C can be taken as 0.051. The
E
pressure distribution is parabolic, and the pressure at any point y below
the top surface is:
PE - C^v/hy" [3-104]
The line of action of force P is 0.4h above the ground surface.
f. Selection of Acceleration Coefficients.
(1) Minimum Acceleration Coefficients. Minimum horizontal acceleration

coefficient values for the United States and its Territories are listed in
ER 1110-2-1806. In the absence of more accurate data, these values can be
used as a guide for determining the acceleration coefficient to be used in the
calculation of lateral earthquake forces on retaining and flood walls. As
discussed in paragraph 3-26b(3)(d) where the horizontal ground acceleration is
0.2 g or less, the vertical ground acceleration can be neglected for all
3-78
EM 1110-2-2502
29 Sep 89
practical purposes. When the vertical acceleration coefficient is included in

the analysis, it is normally taken as two-thirds of the horizontal accelera-
tion coefficient.
(2) Acceleration Coefficients Greater than 0.2. When the design accel-
eration coefficient exceeds 0.2, the Mononobe-Okabe analysis may require the
size of the wall to be excessively great. To provide a more economical struc-
ture, design for a small tolerable lateral displacement rather than no lateral
displacement may be preferable (Applied Technology Council 1981). A method
for computing the magnitude of relative wall displacement during a given
earthquake is described by Whitman and Liao (1985).
(3) Acceleration Coefficients for Walls Forming Part of a Dam. For re-
taining walls forming part of a dam, where failure of the wall would jeopar-
dize the safety of the dam, the selection of the acceleration coefficients for
the design of the wall should be consistent with those used for the stability
analyses and concrete design of the dam, where required (ER 1110-2-1806).
3-79
EM 1110-2-2502
29 Sep 89
CHAPTER 4
STRUCTURE STABILITY
4-1. Scope. This chapter presents information for stability analysis of re-
taining walls and inland and coastal flood walls. The methods of analysis to
determine overturning and sliding stability and to assess bearing capacity are
discussed. The forces as determined in Chapter 3 are used to assess overturn-
ing stability and bearing capacity. In certain cases as described in this
chapter, the same forces computed for overturning may be used to check sliding
stability. In other cases, sliding stability should be computed by the multi-
ple wedge iterative method or by an adjustment of the driving and resisting
wedge forces based on the factor of safety required, both of which are dis-
cussed in this chapter. Loading conditions for the various types of walls and
the acceptable criteria for each loading condition are given for each of the
stability analyses.
Section I. Loading Conditions
4-2. Representative Loading Conditions. The following loading conditions are

generally representative of conditions affecting retaining walls and inland
and coastal flood walls. The loading cases for a specific wall should be
chosen, as applicable, from the lists below. Loading conditions which are not
listed below should be analyzed, where applicable. Note that some walls may
require consideration of loadings from both lists, as discussed in
paragraph 2- 9.
4-3. Retaining Walls.
a. Case Rl, Usual Loading. The backfill is in place to the final eleva-
tion; surcharge loading, if present, is applied (stability should be checked
with and without the surcharge); the backfill is dry, moist, or partially sat-
urated as the case may be; any existing lateral and uplift pressures due to
water are applied. This case also includes the usual loads possible during
construction which are not considered short-duration loads.
b. Case R2, Unusual Loading. This case is the same as Case Rl except the
water table level in the backfill rises, for a short duration, or another type
of loading of short duration is applied; e.g., high wind loads
(paragraph 3-25), equipment surcharges during construction, etc.
c. Case R3, Earthquake Loading. This is the same as Case Rl with the
addition of earthquake-induced lateral and vertical loads, if applicable; the
uplift is the same as for Case Rl.
4-4. Inland Flood Walls.
a. Case II, Design Flood Loading. The backfill is in place to the final
4-1
EM 1110-2-2502
29 Sep 89
elevation; the water level is at the design flood level (top of wall less
freeboard) on the unprotected side; uplift is acting.
b. Case 12, Water to Top of Wall. This is the same as Case II except the
water level is at the top of the unprotected side of the wall.
c. Case 13, Earthquake Loading. The backfill is in place to the final

elevation; the water is at the usual level during the non-flood stage; uplift,
if applicable, is acting; earthquake-induced lateral and vertical loads, if
applicable, are acting. (Note: This case is necessary only if the wall has a
significant loading during the non-flood stage.)
d. Case 14, Construction Short-Duration Loading. The flood wall is in

place with the loads added which are possible during the construction period,
but are of short duration such as from strong winds (paragraph 3-25) and con-
struction equipment surcharges.
4-5. Coastal Flood Walls.
a. Case Cl, Surge Stillwater Loading. The backfill is in place to the

final elevation; the water is at the surge stillwater level on the unprotected
side; wave forces are excluded; uplift is acting.
b. Case C2a, Nonbreaking Wave Loading. This is the same as Case Cl with
a nonbreaking wave loading added, if applicable; uplift is the same as for
Case Cl.
c. Case C2b, Breaking Wave Loading. This is the same as Case Cl with a
breaking wave loading added, if applicable; uplift is the same as for Case Cl.
d. Case C2c, Broken Wave Loading. This is the same as Case Cl with a
broken wave loading added, if applicable; uplift is the same as for Case Cl.
e. Case C3, Earthquake Loading. The backfill is in place to the final

elevation; water is at the usual (non-storm) level; uplift, if applicable, is
acting; earthquake-induced lateral and vertical loads, if applicable, are act-
ing. (Note: If the wall has no significant load during the usual (non-storm)
stage, no earthquake case is necessary.)
f. Case C4, Construction Short-Duration Loading. The flood wall is in

place with the loads added which are possible during the construction period
but are of short duration, such as from strong winds and construction equip-
ment surcharges.
g. Case C5, Wind Loading. The backfill is in place to the final eleva-
tion; water is at the usual (non-storm) level on the unprotected side; a wind
load of 50 lb/sq ft on the protected side of the wall is applied
(paragraph 3-25).
4-2
EM 1110-2-2502
29 Sep 89
Section II. Stability Considerations
4-6. General Requirements. Figure 4-1 illustrates the potential failure

modes for which stability must be analyzed. The basic requirements for the
stability of a retaining or flood wall for all loading conditions are dis-
cussed below.
a. The wall should be safe against sliding at its base, through any soil
layer or rock seam below the base.
b. The wall should be safe against overturning at its base, and, in the
case of gravity walls, at any horizontal plane within the wall.
c. The wall should be safe against bearing failure and excessive differ-
ential settlement in the foundation.
4-7. Stability Criteria. The stability criteria for retaining walls and in-
land and coastal flood walls are listed, by loading case, in Tables 4-1
through 4-3.
Section III. Overturning Stability
4-8. Resultant Location.
a. General Computations. To assess the overturning stability of a wall,

such as the one with a horizontal base shown in Figure 4-2 (see examples 1, 2,
3, 5, 6, and 7 of Appendix N), all operative forces must be applied to a free
body of the structural wedge wall/soil system. Methods to calculate the lat-
eral and uplift forces are discussed in Chapter 3. The moments of these
forces are summed about point O as shown in Figure 4-2 and the distance x
is calculated as:
_ summation of moments about Point 0 r, ,-■

X l
R " ZV " J
where
EV = resultant base force required for vertical equilibrium
A ratio defined as the resultant ratio is computed as follows:
Resultant ratio - horlzontal wldth ofbase ^^
Equations 4-1 and 4-2 are valid for a wall with a horizontal base with or
without a key and for a wall with a sloped base and a key. If a wall has only
a sloped base (no key), as shown in Figure 4-3 (see example 4 of Appendix N),
x is calculated as:
4-3
EM 1110-2-2502
29 Sep 89
~B/
Factor of Available shear resistance

safety " shear requjrod for equilibrium
a. Sliding
U"
Safety assessed by checking base
resultant location
Overturning
id
Use bearing theory for Inclined,
eccentric load, sloping base
c. Bearing
Figure 4-1. Stability considerations for retaining and flood walls
4-4
EM 1110- 2-2502
29 Sep 89
u 4J
o 3
4J o
B 60 >, CJ B 1
a B 4J 3 VJ ■H 41 t».
S ■H -H F* O
• o* O
* O CO «4-1 I-l 4J
•H M U Md B 01 0 0.li 41
c ed to >, CO CM t-i o P o >M
•H « P.U A 01 -H 3 t~* «w CO
as no« N 4J CO ■e- o co CO
>. CO 09 4J
CO rH "3 41 B CO B 0)
CO CO B U CO 4-> -H 4J
s »
CO O
B. u CO o
won
CO
3
<rd M 4-1 er
B « 41 41 M 41
o *J ,~. >H 4J CJ U O •3
id e ■H C B O 1-1 8! a co o 3
•rt o .* «-> sr •* CO iH 4) O » CO 41 Vi
Id ■H U CO K »4 4J X 41 co a •3
01 a>o -3 u"> o H U « *^^ 01 • *J X
CO CO i-l 41
4J 01 n 0Ä B r>- in 3 v) CO a eo M •a •H CO ■3 •
■H 01 0)
(8 M
3 M » 43 U B O 41 « «J h •rt -a
Id O 0) •H B. 4J 41 CJ 3 > 4»
as
U
60s o
to
t Eh sf
1
6
"H
C CO
CO
(0
CO <P4
P.
|4 01
U cd
iH -H B
4J O B
Id i-l
a. 3
(35 o ^ «-■ 01 U cd -3 4J
<H e B •3 CJ •rt B <w 01 X
B •H e O 4J X 1 X 4J O B O r-l O
u B "H 1-1 B B 41 41 B ■H O X
3 •H rH 4-1 ■* -* CO H O 41 CO who 3 CO
4J
w
s CO •H CO K M W£
Hun
41 -4 P B U «H 4J «J iH
01 O *3 O m •4-1 01 4J ■H CO B.
01 Id CO B o 1". 3 i-l 3 V • XJ o Id "3 01 41 41
< >. »
CO
■H
U
£ 3
O
Eh
1—t «0
01
05
» X ^4
>> O
4J pU
1-4
B CO
B
CO
IW 41
B
41 -rl
4J
M
CJ Id
CJ
3 rH
3
3 •H 0 Xi 1-1 X CO CO •H
u tH 4J U U 41 3 3
•H ■H • CO 6C u X X X Xd
U u u Id ^3 B JS B •H B O CO
u •a en 10 CO CO (0 O 4J 01 O >> 60
01 B 01 41 0) 4> -H 60 M B 01 4J 3 B
►» x s e -rt
4-1
■H
Id
■H ,M
O
<H (0
X
CO
£
CO BS «1
4J
CO
01
X
»
■3 X
01
CJ
4) td
rH
1
rH
«H
3
er
0)
CJ
O
BS
4J
CO
-a
*J
u
4J
CJ
4-1
CJ
4) •«
P. B
<-^ o
I-l
4-1
CD
O*
09
VO
CO rH
X 3 <3
M
i-l §s
O X
-a- * OS B a> 4) V O 0> X O X
eg 3 M M u 60 CO CO 4J 0) X V4 CO *3
01 4J u O •H •H ■H B 4J 3 60 X CO 0 B
i-t co a> Eh o o O •H 10 m B B 3
0) B h o m 0) "3 CO » 3
CO rH H •H O «u CM h H 41 J< 8 4J
H rH CO » « <J 3 3 CJ i-l c
.2 X B U « CO O i-l O B 01
S 4J
60
O
— nd
•O 01 N •3
B CO
X
CO
CO
>
l-i "d B
e 4>
60 B 4J «t « 01
J=
4-1
*►»
iH CO B rH
C 01 CO CM CM 01 CO •3 M 41 O 0) 4J
•H u •a y—s /—s l-i u B i-i B CJ X X 4->
(3 u B CO CO VM 0 CO Pü CO 4J (J)
•rt 03 3 U-l «4 Ü CO
CO O w Id <J •* CO •3 o B
4J Id Eh o o O B <**» B • h 3 r-l
01 a ^»^ ^■n. B 60 o
01 41
(0 «J o A: X 3
OS 4) i-l v9 *B •H 01 CO CO y na U i-l
£ id r°* 0) CO n CJ P. i-l o s 4-1
CO O o- ©•
^-^ O* U 4) ^■^ •H i-l M CO B B
CO w >—' «0 *o 6 B CJ 9 o v
u •H 1-t » B ^! ■H Id
JS «3 4J O CJ CO 41
U B ■31 09 B CO O CO ltd
CO •H CO 1 60 CO ^ It 3 <td
M-l Eh JS o B 144 CJ Id id
00 o » CO •H CO O O B 0."3
B » CO
■-4
J: •3 •H M 0 e
•H l-i >, U1 CO CO *J X CO CO O 41
■a o 4J • • • B 60 0 B fl I-l 41 O rH
■H 4J 0) «-4 P-H «—1 O S © f-t 0 HOW X
H U U ■H 0) r-4 •H >> 41 B 3
CO 3 3 4J Id e 4J i-l ^ I-l
• ■H 4J
Ob CO CO *J A o CO CO CJ u B.
•3 CO •H •3 BOB CO 3 «
B >. U B WHO 4) V CJ
3 CO 4J CJ 3 CJ B Id u
01 O ■H 3 O 60 B cd 3 3
B A! «4-1 -3 rH U <4-i B O <*-i iH B
60 O CO B •H 4J •H O B. 3 3
ß H r-l 3 rH CO XI CO rH •3 01 3
■H 4J CO er •H CO B •H i-l «J CO 60 3 *J
•3 -H rH 3 £ o o- 01 o O i-l 41 41 B X CO
o
CO
o s
i-l
>3
o
CO
3
CO
09
3
B
«J
H
CO
CO
M
x:
4J
B
4) p
CO
41
CO
CJ
Id
i-l
P.<3
«BS •3
1-4
3 IH
3 3
B
u » S W O O a. o X X O CO 0) 3 60
(b X s-> Pu 4-1 H CJ CO X ►J 3
0) 01
to • —1 CM CO 4->
CO o PS" £>£ os o • • • •
U 2 a t—t t>4 CO •»
4-5
EM 1110-2-2502
29 Sep 89
i-l
o B
u o
B 60 >> CJ CJ 4J
C u «
3 1-1 I-l 3 *►.
S 1-1 to o• o
• o• o
• O CO <4-l CJ 4->
i-tM O <4-l B O 1 I-l a>
B cd cd >, en CN «—t CM o eu O U-l
■H « au A CO 1-1 I-l *-> I-l cd
X n a oi
(tan $
s of p
joints
N 4-> •H CO
U <4-l >s cd o
CO r-l "V CO CO
CO Cd B 44
B 3 0) cd
Cd O 43 3
B IM 4J 4J er
«a B o 4J M CJ co j«: 01
•H O I-l B B ^-v I-l E CJ 0) CJ 13
vi
01
i-l
a
44
u
«
cd
<r
«*8
•a-
K
cd -H
44 43 01
•**« CJ 1-1
01 O
■H B 4J O
cd i-i
cd
44 01 (A o *o m o HUH o *—^
CO CO 01 4-1 U 13
■H CO 0) Be. B r-» io 3 i-l cd m I-l en id I-I CO
vi M IJ 3 10 9 43 6 60 3 •H eo cd •3 •
c_> n ft o
to eg a B
•H
CO CO 43 Vl
01 CD 3
•H T>
CO > CO
Ö0 B 5 -* B 01 Vl 4J O B
B 3 u 1 1-1 I-l 4J Cd Vi iH
•H B B o cd a. •HUB ft. Cd
c •H B o 4-1 -* I-l cd cu 4-1
Vl B •H •H B S ■3 p B Vi I-i 01 43
0
4-)
■H
s
r-l
cd •H
4J
cd
•»6~3 «*»-8 Cd
u
1-1
43 cu
sf
6-S
X 1
01
a)
4-> >0
• O -H O
■H -a
rH O
43
n 01 o *3 o m I-l 4-1 CO in O 01 cd oi 4-1 C0 cd co
0)
 43
V
U-l
u
•
>. oi a.
U i-l
cd 1-4 O CO
Vl Vi 01
U U4 u
01 0)
CJ Vl
U >. o I-l o u CJ 3
V 4-i to B 0,-ri 01 13 Vc ed r-t
4-1
•H
•H o 4J 43 01 Cd 1-1
I-l u Vl U I-l (0 B 44 B 01 cu cd
U "3 en cd cd cd cd •H • eo to cd •H 43 43 M-4
O 0» B 0) 0) 01 0) 43 B 43 01 B cd to
M O 43 43 43 43 cd o 4-i CJ 4J O 4J >t 60
>> •H
3 î 4-1
•H CO CO CO ca 0) i-l 00 X o 43
*o o o
4J cd B
4-1 B
•H
F-l
tr u ed
01 O -3
4-1
u
4-1
u
44
O
4-1
CJ
Sä
01 t3
cu
I-l
01
B CO
B
at cu
CO CU Vl
B i-i
Vi
B cd
CM 1-1 Sei OS B 01 0) 01 01 B. B 4-1 0) i-l cd 43 -H 9 eo
1 43 3 Vl I-l Vl u •^ o CO •e» 43 "O O 43
sr at 44 O ■H 1-4 •H 1-1 o 4J 13 43
oi
■u
en
CO
OI
to O o 1=1 o 60
B 4->
en
to
•H 01 i-l Vi
43 3 O
CO t3
_ B
i-l H •H CO u 43 B o e cd
43 —1 B »4 o 4-1 01 13 43 - 3
cd i-H 4S B •i-l o IM 60 43 i-l CO 4«! B 4-1
H «0 4J O cd 3 B & 3 CJ •H ß
3 60 •H (-1 a) 01 O CO O B o>
s 4-1 •O 01 N I-l to 43 0) t- •H B
"3
o
01
M
Cd
■3 ^—^
i—l t—4
*—* CM
^-s 01 4-1
>^
r-l
4-4 43
CO 4J
CO 3
.-I 6
B eu
i-l
o 4-1 B en en en 01 cd 60 44 CO O 01 4J
iH en 3 I-l ^ B O* B CJ > 43 4J
to Vl
O
to )-i
o o
vi
o
l-< m o
U-l
cd
0)
0)
M
O
Vl 01
44
CJ
4-1 CO
CO
13 cd ^■^ *s^
«5
— 4-1 4M
^^. CO 4J
B S Vi
B
B at i-l i« o0 O B 3 CO cd »-I
«0 43 •H i^v B 60 CJ 0 4= CO
l-H en O O* o-
*^ o- o*
^-^ •H GJ - en "O 4J H
C en 4-1
(-1
N—' N—■' 0) CO
I-l 0) ^^,
(0 CO
01 13
rl • B
iH 44 Cd B S
cd 13 ea to B
cd cd
cd ej
& O 44
O
•H
CU
Vi
en 43 -a ü Vi CJ CO CU
U-< Pa ü B -a- •3 cd o CO H-l
60 O -H cd 1 60 01 B Vi 01 >4-l
B en en 43 o B 4J <4-l O u n
■H Vi >* in en r-4 en S ca •H cd O B
13 O 4J •
«—1
•
*—i
• • 4=
*—1
"O o. 44 O
ft. 13
B
•H 4-1 01 ^■4 i—i CO 4-> X cd i-l CO CJ O 01
i-< CJ «4-4 B 60 o o i-l O 0) CJ i-l
en eo cd O 6 o iH 1-1 CO Vl 4-1 _ 43
in en 1-4 01 f—1 4J >t 01 B cd
4-1 I-l B B i-l Vi Vi 1-1 4->
Cd 4-1 A O cd cd o cj •
CO
ft.
01
13 CO B B CO
13
O
p.
o
B
O
s
3 en
^>
4J
4J
CJ
CO
-i-l
Cd 44 O 0)
CJ ej B
0)
Vi
CJ
CJ
B O 4-1 01 •H o 1-1 3 60 O Cd co cd
60 O t-4 i-l Ai 4-> M-4 T3 I-l Vi B C U K-l iH B
B i-l M-l 0 i-l CO U B 1-1 4J O •H Oft. cu 3
i-l 4-> 4-> Cd 3 3 iH Cd 43 CO i-l 13 6 eo
•3 1-1
cd tj
B
60 u
& er
43
l-i
4-J
•H
o ey
ed
0)
B
O
4J
cd
•H
i-l
O CO 60
eu B
Cd 44
43 CO
■H
O B
►J o
u
03
01
01 4-1
44 O
cd
4U
V.
cd
CO
o
s
CO
43
U 4J
B
01
cj
B
H 3
"3 C0
oi
0) i-4 i-l
4J Out}
eu B "O
B
eo i-i
to cd
0 » to u o o
to 43
ft o o
to u-i
43
H
Vi
O
Cd CU
C0 43
01 60
►J ed
to
0> 01
CO • •—< CM en -a- 4-1
• • • •
cd O (-4 M i-i r-l o
u z S= »—t eN en -3-
4-6
EM 1110 -2 -2502
29 Sep 89
M 01
o •o B 4J
u c co O 01
1 60 ►. O
B 4-1 CD
E •H -rl It. o• o• m
• o
• o O o
cd
Oô
•H
B U B
kl
oi cj
4J
• 4J
Cd
•H kl ü r-l O CU O to B
6 es es >, OI CM «—1 CM •—1 CM eM a ■H kl CJ 0) iH
■H « P.U A 4-> A 4-1 CJ 4-1 Cd
X CO «9 4) o cd 8 OH 60
U <M ■O >s ■a O O er cd
cd 4J s O
CO 3 co ki >»
O i-l O WH CU 0 4-1
U-l -H 0 f-4 <4H 09 CU
<!H
cu es
2-
ß rH ^ B 01 4-1 cd
o 4J N 01 •rl -o es N 60 co
CD c •H e <: O co • >» B
•H o Ji u m m m m CS -H 0) m in I-I E CO B co rH 01 01
kl ■H o es M> (X M K 4J J3 C0 w X cd cu et u v CS kl 4-1
« 00 o -o in o O O i-l 4J cd o o (3 O. cu 4J 3 ß ß 4-> cd
4J «1 to OS ß f- m •» m 3 TJ J3 m m cd'-' J= *" cj CS es to 3
T4 CO 01 3 co 9 4-1 1 r-t er
1-1 Cd kl o cu - n CU CU B. at CO cu
fa B u
U 03
60 E
t
o
OS
CJ
01
O
iH
•rl
U kl
B B.
CS
60
B
CJ
0)
u
o
Cd
u co ■4H •o
5g c
CO
—
W
cd
CU
kl
4J <4-
to o *o
-rl
*•*- CU
g-s
3 iH
6
•H o
•rt
4J
e e
a •«
CJ C
3
3
CO
co
IH 13
C0 C0 01
0) 4J JO
B
u
cu
N
>.
13
•H
>
4- £ Cd i-C 4-1 m in in m cd -H oi m in •» O cu kl CD 4 rH o
u 01 •H Cd ** »4 »4 ►4" k> J3 C0 K »4 1 CM kl 01 ki 1 es kl
u ki o *o © m O m HUR m m o o. H 14 O o ß o.
•< r— V0 r~ r>-
es
5 co c
3
o
o 3 -H A
CO »
01
t-- -« rH
■H
X O
u
cu
cd
B n co
O Cd 4J
1—I
X
cd
•
cu
rH •
■H tu OS CO 4J ■H S) B ^^ .O 13
kl o S 4J J3 -H o o cd CU
«1 rH 60 » O CD O rH cu 4-1 B
4J e •H i-l co
^-,
B-lH
•H V
-H 01 kl 4J V oi cd
u kl ki kl ki ki ki ki 13 kl «4 U « 6 CJ 4J
u O CS cd Cd Cd cd es Cd >M-I O 0) o >» CJ u ja
•o B 01 01 0) 0) cu 0) eu U CS B. 01 (H O 4-1 cd o
>> 0) o •ß A £ « * A •ß 1-1 kl £<H h iH «»
4J kl M iH CO CO CO CO co to co rH •« CO 4-> «O r-^ 1 4) co
iH •H CJ 4J •H | CO rH •H O rfJ -rl
I-H s o cd 4J *J 4-> «-> w 4J 4J ja oi 0) B 8 cd Ä rH
iH tr OS U u O CJ CJ CJ CJ o cd eu o O O kl cs >. CU
e cu
in
1
-»
JO
CS
4J
0)
OS 3
o
01
kl
■rl
01
kl
■H
0)
kl
iH
ki
iH
01
kl
■rl
CU
kl
1-1
01
kl
•H
g«.
CU kl X
0) TJ
CU
•
CU
ki 3
TJ l»H 4J
cd
0)
B
X
o
cd ki
S 3
r-i
fa o o
01
iH
CO
i-l
u
to
01
Q O O O O
w tu
01
o. o
kl ß «
cu cd
•s o. «
C0 13 ß
cd cu
Ct4
01
o.
^-*
m*
Al
g-s
O <4H
.B r-< H » -H IH O J3
Cd (9 60 O cu cd 60 >> C0 60
H 3 c C0 iH « 44 II ß U
4J o i-l B J3 4J .n 4J ■rl •H B-S
■o 60 i-i c o • 4J B ton B •-I 2 u
o ß 4-> •H -H ^ 60 CS rH CU •H iH e es
o 01 es i-H •—i CM CM cd «J rH B 3 01 4J es -o iH CU
i-H kl 13 /—\ /■^ <~* /—* kl 1-1 B 0) 4J O x> IH cd B ja
&. 4-4 ß IQ CO CO CO •a T3 O kl O J3 kl 13 01 •rl
B
to 9 13 4J B to 13 es
rH
CD kl tu
o kl
O
u
o
kl
o o
kl 01 O
01 o
CO
JS
to
co «3«
rH CU 01
01
Ecu cu co
"2
B
4H CO ^, *^ *»^. kl 4-1 O-lH Ü o CO ki B. J=
CO 01 i-H •43 «a ■» •3- •41 <4) IM u 60 0 J! <4H v-x 4-1 4J
Cd X. ■H ^^ *—N ^-^ CO B 0) 4J kl C0 4-1 B
o CO O O* ©• er
*«• O*
V-*
o-
^^ O c
*~* w
W kl 01 C0 IH U 4-1 CO B 01
c_> co *-• o o kl 3 ß 10 01 O ß cd B
c s 4J B o oi ki ß o £ 01
CO • cu 3 -rl iH
0) 01 co X HiHTl 4) 4-1 4-1
kl X CO oi 9 rH Cd ki CS S 4J
CO Cd w co es > H es 13 O 01
UH tu kl cd co » o B IH C0
60 O ■C kl o CJ 43 cu X 3 co
c ci
cj o 14-1 4-> cd « - CJ
iH
O
<4H
C0 r-t
01 Cd
iH ki >■ cn in rt er> •H U-l 60 60 H Ji
13 O 4J m c> CJ P1 (-4 Cl en X 01 B B U-4 CJ ■c kl -H
«4 U «I • • • • • • • > c N ■H 01 o o & <-i B. u
H U IW «—i *—i rn rH ■Mt «-H i—i 60 ►, ■W ki • kl ■H B ß
co es cs CO iH rH 10 4-1 CO Ji co O O 01
ck on
I*. en
n roc
ß
alysl
(3 CO cd O CO CO CJ kl
O 01 iH o eu
•H •«
4-1
g B
CO •H
4-1
60
B
ß UH
•H lu
cd -O O TS cd iH iH
M 60 C •O es >-N IH B BOO u ß cO 13
0) B O C cd o 4-1 cd cd , u B iH cu
ß 4-4 •H CU •H 3 01 u M 3 CS ki 41
60 O Cd .* 60 ■X. 4J o co co
^-* 3 *0 60 O 73 O kl Cd rH
ß -H S cd C cd CJ <M J3 kl 01 BOB <|H 13 -o
■H 4J i-i 0) •H c 3 3 4J e 4J 4J •H ki cd 01 Cd
13 -H i-i ki .* 01 er M rH 60 o co cd •o rH CU CO 4J
CO 13 0) -H -O cd a J3 4J •H e B O. iH kl J<! iH CU Cd B.
O ß 60 4-1 0) c 01 o u co t) 0 CU sf 0 IH I-H O CJ 0 ki jD cu
►J O kl C0 > o ki ki U C C co ki 1 u cj C0 O CO UH ü
ü 3 CS z cd B3 CS o •H U o •H J4 U CO CJ
C/l Sät u u 3 u to —4 kl 4J 01 CJ kl ki C0 Cd
o O B X O ß o o CU B
(b CO X tu cd EH H O tu tii ►J 3
10
0) ■ CS •o o 0)
CO • -H CM CM CM CM m ■äf m 4J
CS o u u u o O O u o O • ■ • • •
u z1 z t-H CM en -a- in
4-7
EM 1110-2-2502
29 Sep 89
CO
CO
c
o
to
•H
Et
s
>-l
o
4-1
CO
>,
eo
C
CO
60
c
•H
c
M
4-1
J-l
0)
>
o
u
o
IM
CO

CJ
H
o
fa
-a-
*
rH
cd
Pi
cd
00
a
■H
(3
M
\ -M 9
\\ +*\
x>\
4J
U
\ *"*k\ a)
\ *♦■* * i >
o
—Vs-^\
\3*£\
u
o
r-—A
.A o\
CO\
«H
co
a*
o
u
o
f*.
CO
I1
a>
u
3
60
F»
4-9
EM 1110-2-2502
29 Sep 89
summation of moments about Point 0 r, _-,

R effective normal base force, N1
The resultant ratio is defined as:
X
R
Resultant ratio - — T-T ryrr [4-4]
sloped base width
The resultant ratio is related to the percent of the base in compression as

shown in Figure 4-4. The percent of the base of the structure which is in
compression should be checked for compliance with the overturning stability
criteria discussed in paragraph 4-9.
b. Walls with Keys.
(1) Performing an overturning stability analysis on a wall with a key

requires determining the resisting forces acting along the key and along the
base. Since these forces are indeterminate and cannot be determined by equi-
librium methods, the following assumptions are made in order to compute the
overturning stability. For a wall with a horizontal base and a key, the
shearing resistance of the base is assumed to be zero and the horizontal
resisting force acting on the key is that required for equilibrium, as shown
in Figure 4-5. For a wall with a sloping base and a key, the horizontal force
required for equilibrium is assumed to act on the base and the key, as shown
in Figure 4-6. In both cases the resisting soil force down to the bottom of
the toe may be computed using at-rest earth pressure if the material on the
resisting side will not lose its resistance characteristics with any probable
change in water content or environmental conditions and will not be eroded or
excavated during the life of the wall. See examples 3 and 6 of Appendix N for
stability analyses of walls with keys.
(2) Prior to performing an overturning analysis, the depth of the key and
width of the base should be determined from a sliding stability analysis.
c. Sloping Backfills. For an upward-sloping backfill, an additional

shear force can be taken advantage of in the overturning analysis. The calcu-
lation of this shear force is shown in Figure 4-7. The magnitude of this
shear force is just large enough to cause the horizontal forces acting on the
stem to be equal to the part of the horizontal wedge force that lies above the
heel of the wall. This will cause the force used for the structural design of
the stem to be equal to the force used in the stability analyses. This force
will also cause the summation of moments about the stem-toe-heel joint to
equal zero for the structural design. The derivation of this shear force is
given in Appendix K. A wall with a sloping backfill is shown in example 1 of
Appendix N.
4-10
EM 1110-2-2502
29 Sep 89
o
U
cd
u
o
JZ ro 4J
ro
+■ ro 6
•r O 3
(0
X (D
« d) 3 +- W _ r- ro
tJ
(0 (0 0) c a oioOCoro e
(DO®® m io CMa evi• —■ —■
ooooo §
•H
II CO
CO
o a
c
o <
a:
ZJ
(0
© • z .0
QC +" < *J
. c
c ^-= H- •o
•H
pof
_l
Ion
&
© CO
to w UJ
01
u
o a: CD
ja
n 2:L C
a a>
o e+*o
0)
o o
o
w
01
43
o 43
CO
CO e
o
CO
L±J
c IT
JZ Q-
■+- _ 2 Pi
O
O
tral th
'/. base
z
ipressl
I
ultant
o X X .V X
nifiOOO
l^B
<D
w <
— r- to in ^ at
o u
UJ 9
00
ritfflC <
Ö O ® <D H~
= otz O O UJ
CO
<
CO
4-11
EM 1110-2-2502
29 Sep 89
+-
*i
IE
X o
(0
o C
cd
CD
cu
ii co
cd
o .ß
iH
cd
o c
cc o
o N
2 > +- ■H
1-4
L.
W W o Ä
O
+-
X!
3 ■U
(0 •H
<r <D &
X Q:
cd
&
M
O
m
co
•H
CO
C8
x: c
cd
00
4-1
V4
0)
>
o
o
4-1
CC
cu
u
S-i
o
Pn
m
i
u
D
Ü0
•H
[14
4-12
EM 1110-2-2502
29 Sep 89
CO
n)
,£>
00
C
•H
P.
O
5
■H
cd
&
n
o
<*A
CO
•H
CO
>t
rH
cd
a
•H
a
3
r. 4J
+- H
cu
"O !>
o
$
Vt
© o
M-l
W
o CO
0)
CD O
H
o
I*.
4-13
EM 1110-2-2502
29 Sep 89
1 ///MM i i
h
2
imw T
■A .
A
A
A
1
///mm
1
Line of action
of resultant
force
S = P (h, - h2 ) = Shear force when h, > h2

3a
Figure 4-7. Shear force for upward sloping backfill
4-14
EM 1110-2-2502
29 Sep 89
d. Uplift For Walls with Keys. For walls with keys, the soil may be
assumed to remain in contact with the key and head loss to occur around the
perimeter of the key and along the base even if the overturning analysis shows
less than 100 percent of the base in compression.
4-9. Overturning Stability Criteria. The overturning stability requirements

in Tables 4-1 through 4-3 are given as minimum percent base areas in compres-
sion. Figure 4-4 illustrates the relationship between the percent of the base
area in compression and the resultant location.
Section IV. Structure Sliding Stability
4-10. Overview of Sliding Stability Analysis.
a. Purpose. The purpose of a sliding stability analysis is to assess the

safety of a structure against a potential failure due to excessive horizontal
deformations. The potential for a sliding failure may be assessed by
comparing the applied shear forces to the available resisting shear forces
along an assumed failure surface. A sliding failure is imminent when the
ratio of the applied shear forces to the available resisting shear forces is
equal to 1.
b. Analysis Model.
(1) The shape of the failure surface may be irregular depending on the
homogeneity of the backfill and foundation material. The failure surface may
be composed of any combination of plane and curved surfaces. However, for
simplicity all failure surfaces are assumed to be planes which form the bases
of wedges as shown in Figure 4-8.
(2) Except for very simple cases, most sliding stability problems en-
countered in engineering practice are statically indeterminate. To reduce a
problem to a statically determinate one, the problem is simplified by dividing
the system into a number of rigid body wedges, arbitrarily assuming the direc-
tion of the moment equilibrium forces which act between the wedges, and ne-
glecting any frictional forces between adjacent wedges.
(3) Figure 4-8 also illustrates how the failure surface would be divided
into wedges. The base of a wedge is formed from either a section of the fail-
ure surface that lies in a single soil material or along the base of the
structure. The interface between any two adjacent wedges is assumed to be a
vertical plane which extends from the intersection of the corners of the two
adjacent wedges upward to the top soil surface. The base of a wedge, the ver-
tical interface on each side of the wedge, and the top soil surface between
the vertical interfaces define the boundaries of an individual wedge.
(4) In the sliding analysis, the retaining or flood wall and the sur-
rounding soil are assumed to act as a system of wedges as shown in Figure 4-8.
The soil-structure system is divided into one or more driving wedges, one
structural wedge, and one or more resisting wedges.
4-15
EM 1110-2-2502
29 Sep 89
Driving Structural wedge Resisting

wedgo
Alternate planes
below structure
are analyzed to
determine critical
ure path.v
Assumed
slip
planes
a. Failure plane for wall without a key
Driving Structural wedge Resisting
Alternate planes
below structure
are analyzed to
determine critical
failure path.
Assumed
slip
planes
b. Failure plane for wall with a key
Figure 4-8. Typical soil/structure system with an assumed

failure surface
4-16
EM 1110-2-2502
29 Sep 89
(5) Depending on the geologic conditions of the foundation material, the

the location of the total failure surface or parts of the failure surface may-
be predetermined. The inclination of some of the failure planes or the start-
ing elevation of the failure planes adjacent to the structure may be known due
to natural constraints at the site. Conditions which warrant the predetermin-
ation of parts of the failure surface include bedding planes or cracks in a
rock foundation.
c. Analysis Procedure of the Soil-Structure System. An iterative proce-

dure can be used to find the critical failure surface. For an assumed factor
of safety, the inclination of the base of each wedge is varied to produce a
maximum driving force for a driving wedge or a minimum resisting force for a
resisting wedge. The assumed factor of safety affects the critical inclina-
tion of the base of each wedge. The factor of safety is varied until a fail-
ure surface is produced that satisfies equilibrium. The failure surface which
results from this procedure will be the one with the lowest factor of safety.
Several base inclinations of the structural wedge, such as those shown in Fig-
ure 4-8, should be evaluated to determine the failure surface which has the
lowest factor of safety.
4-11. Sliding Factor of Safety.
a. General. Limit equilibrium analysis is used to assess the stability

against sliding. A factor of safety (FS) is applied to the factors which
affect the sliding stability and are known with the least degree of certainty.
These factors are the material strength properties. An FS is applied to the
material strength properties in a manner that places the forces acting on the
structure and soil wedges into equilibrium. Since the in situ strength para-
meters of rock and soil are never known exactly, one role of the FS is to
compensate for the uncertainty that exists in assigning single values to such
important parameters. In other words, the FS compensates for the difference
between what may be the real shear strength and the shear strength assumed for
the analysis.
b. Definition.
(1) A state of limiting equilibrium is said to exist when the applied

shear stresses are equal to the maximum shear strength along a potential fail-
ure surface. Therefore, a structure is stable against sliding along a poten-
tial failure surface when the applied shear stress is less than the available
shear strength along that surface. The ratio of the shear strength to the
applied shear stress along a potential failure surface is defined as the FS ,
as shown in Equation 4-5.
ll = Pa1 lean
FS = -£ (tan y
d») +
T c
C [A_5]
T T
4-17
EM 1110-2-2502
29 Sep 89
where
X = maximum shear strength according to the Mohr-Coulomb failure

criterion
x = applied shear stress
(2) The sliding FS can also be defined as the ratio of the shear force
(T ) that would cause failure along the slip plane to the corresponding shear
force (T) along the slip plane at service conditions (see Figure 4-9):
FS - £ - N' ta
V + CL
[4-6]
where L is the length of base in compression for a 1-foot strip of wall.
For c = 0 ,
„„ _ N' tan <fr _ tan <j> r, -,■■

l J
N' tan $ tan <|>d
or for <|> = 0 ,
FS = -Sk
where tan <[> , c is that portion of the shear strength considered to be

mobilized or developed along the slip plane(s).
4-12. Assumptions and Simplifications.
a. Slip Surface. The slip surface can be a combination of planes and

curved surfaces, but for simplicity, all slip surfaces are assumed to be
planes. These planes form the bases of the wedges. It should be noted that
for the analysis to be realistic, the assumed slip planes have to be kinemati-
cally possible. In rock, the slip planes may be predetermined by discontinui-
ties in the foundation. If alternate planes are possible, all must be
considered to find the most critical.
b. Two-Dimensional Analysis. The sliding equilibrium method presented is

a two-dimensional analysis. This method should be extended to a three-
dimensional analysis if unique three-dimensional geometric features and loads
critically affect the sliding stability of a specific structure.
4-18
EM 1110-2-2502
29 Sep 89
4-19
EM 1110-2-2502
29 Sep 89
c. Force Equilibrium Only. Only force equilibrium is satisfied. Moment

equilibrium is not considered. The shearing force acting parallel to the in-
terface of any two wedges is assumed to be negligible. Therefore, the portion
of the slip surface at the bottom of each wedge is loaded only by the forces
directly above or below it. There is no interaction of vertical effects be-
tween the wedges. The resulting wedge forces are assumed horizontal.
d. Displacements. Considerations regarding displacements are excluded

from the limit equilibrium approach. The relative rigidity of different
foundation materials supporting the structure and the concrete structure it-
self may influence the results of the sliding stability analysis. Such com-
plex structure-foundation systems may require a more intensive sliding
investigation than a limit equilibrium approach. The effects of strain com-
patibility along the assumed slip surface may be approximated in the limit
equilibrium approach by selecting the shear strength parameters from in situ
or laboratory tests consistent with the failure strain selected for the stiff-
est material.
e. Relationship Between Shearing and Normal Forces. A linear relation-

ship is assumed between the resisting shearing force and the normal force act-
ing on the slip plane beneath each wedge. This relationship is determined by
the Mohr-Coulomb failure criterion.
f. Structural Wedge. The general wedge equation is based on the assump-

tion that shearing forces do not act on the vertical wedge boundaries. Hence,
there can only be one structural wedge since concrete structures transmit
significant shearing forces across vertical internal planes. Discontinuities
in the slip path beneath the structural wedge should be modeled by assuming an
average slip plane along the base of the structural wedge.
g. Interface of Other Wedges with Structural Wedge. The interface be-

tween the group of driving wedges and the structural wedge is assumed to be a
vertical plane located at the heel of the structural wedge and extending to
the base of the structural wedge. The interface between the group of resist-
ing wedges and the structural wedge is assumed to be a vertical plane located
at the toe of the structural wedge and extending to the base of the structural
wedge.
4-13. General Wedge Equation.
a. Sign Convention.
(1) The geometry and sign convention of a typical i wedge and adjacent
wedges are shown in Figure 4-10. The equations for the sliding stability of a
general wedge system are derived using a right-hand coordinate system. The
origin of each wedge is located at the lower left corner of the wedge. The
x-axis is horizontal and the y-axis is vertical.
(2) Axes which are tangent (t) and normal (n) to a failure plane are
inclined at an angle (a) to the +x- and +y-axes. A negative angle is formed
4-20
EM 1110-2-2502
29 Sep 89
»- +X
POSITIVE ROTATION
OF AXES
NEGATIVE ROTATION
OF AXES
l+h WEDGE
st
(!-I ) WEDGE (STRUCTURAL
WEDGE)
(l+ls+) WEDGE
Figure 4-10. Geometry of typical i wedge and adjacent wedges
4-21
EM 1110-2-2502
29 Sep 89
from a clockwise rotation of the axes. A positive angle is formed from a

counterclockwise rotation of the axes.
b. Derivation.
(1) By writing equilibrium equations normal and parallel to the slip

plane for a typical wedge as shown in Figure 4-9, solving for N; and T. ,
and substituting the expressions for N' and T. into Equation 4-6 for the
factor of safety of the i wedge, the following equation results. (Refer to
Appendix L for a detailed derivation.)
FS = I [(WL + v±> cos 0± + (HL. - HR1) sin a±
+ (P^ - P±) sin a. - U±] tan ,± + c.L. ( / [(HL1 - H^) cos a±
p
+ (P±_! " ±) cos a± - (W± + V±) sin »J [4-8]
solving for (P. - P.) gives the general wedge equation,
(P i-1 ~ Pi) =
[(Wi +
V(tan <frdi c°s a± + sin a±) - U± tan ^
+ (\± ~ HRi) (tan $di sin a - cos a.)
+ C
diLiJ / (cos a
i" tan
*dl Sin a )
i f4 91
~
where
i = number of wedge being analyzed

th
(P, - P.) = summation of applied forces acting horizontally on the l
wedge. (A negative value for this term indicates that the
applied forces acting on the i wedge exceed the forces
resisting sliding along the base of the wedge. A positive
value for this term indicates that the applied forces acting
on the i wedge are less than the forces resisting sliding
along the base of the wedge.)
W. = total weight of water, soil, rock, or concrete in the i

wedge
V. = any vertical force applied above the top of i wedge
4-22
EM 1110-2-2502
29 Sep 89
tan (b,, = tan d).

T /FS
di i
1~ Vi
a. = angle between slip plane of the i wedge and the
l
horizontal (positive is counterclockwise)
U. = uplift force exerted along slip plane of the i wedge
H . = any horizontal force applied above the top or below the

bottom of the left side adjacent wedge
H = any horizontal force applied above the top or below the

bottom of the right side adjacent wedge
c,. = c/FS
di
L. = length along the slip plane of the i wedge
(2) This equation is used to compute the sum of the applied forces acting
horizontally on each wedge for an assumed FS . The same FS is used for
each wedge. The system of wedges is in equilibrium if the horizontal forces
calculated from Equation 4-9, for all wedges, sum to zero.
4-14. Slip-Plane Angle.
a. Definition of Critical Slip-Plane Angle. The slip-plane angle a

varies with the value of the FS . For a driving wedge, the critical a
would be the angle that produces a maximum driving force as calculated using
Equation 4-9. For a resisting wedge, the critical a would be the angle that
produces a minimum resisting force as calculated using Equation 4-9. Since
the determination of a is a trial-and-error procedure, for an initial trial
the slip-plane angle a for a driving wedge can be approximated by:
= 45° + ^ [4-10]
where <j) = tan (tan <|>/FS) . For a resisting wedge, the slip-plane angle
can be approximated by:
a = 45° - |4 [4_H]
b. Computation of Critical Slip Plane Angle. The above equations for the
slip-plane angle are the exact solutions for wedges with a horizontal top
surface with or without a uniform surcharge. Other methods to calculate the
4-23
EM 1110-2-2502
29 Sep 89
critical slip angle, for conditions other than a horizontal top surface with
or without a uniform surcharge, may be found in paragraph 3-13.
4-15. Single Wedge Analysis.
a. Introduction. A quick check of the sliding stability of a structure

can be obtained by performing a single wedge analysis of the structural wedge
using the same loadings computed from an overturning analysis if the minimum
required sliding FS is no greater than 1.5. If a minimum sliding FS
greater than 1.5 is used, driving forces would be larger than the forces cal-
culated from the overturning analysis, which uses an SMF (paragraph 3-11) of
two-thirds. In this case, the single wedge equation might incorrectly indi-
cate the structure to satisfy criteria for the larger FS (see para-
graph 4-15b(5) for removing this restraint). Example calculations are shown
in Appendix N.
b. Procedure for Single Wedge Analysis.
(1) Compute the sliding resistance required for equilibrium parallel to

the assumed sliding plane beneath the structural wedge. Use the forces com-
puted from the overturning analysis for the same loading case being analyzed
for sliding. The sliding resistance required for equilibrium is calculated as
shown in Figure 4-11.
(2) Compute the total sliding resistance available along the assumed
sliding plane beneath the structural wedge using the unfactored shear strength
parameters and divide the total sliding resistance by the minimum factor of
safety required for the case being analyzed.
(3) If the sliding resistance needed, as computed in step (1), is equal

to or less than the available sliding resistance divided by the minimum
sliding factor of safety as computed in step (2), a multiple wedge analysis is
not required. A multiple wedge analysis would give a sliding FS equal to or
greater than the minimum required. This check on the sliding stability can be
expressed by:
N + CL
T * ' ^ [4-12]
where
T = resultant of sliding resistance parallel to the assumed

sliding plane required for equilibrium
N' = resultant of forces normal to the assumed sliding plane
tan (]) and c = unfactored shear strength parameters of the foundation

material through which the sliding plane passes
4-24
EM 1110-2-2502
29 Sep 89
L = length of sliding plane beneath the structure
FS = minimum sliding factor of safety required
If the assumed sliding plane is horizontal, T would equal the resultant of

the horizontal forces and N' would equal the resultant of the vertical
forces. See example 1 in Appendix N.
(4) If Equation 4-12 is not satisfied, perform a multiple wedge analysis

to determine the actual sliding factor of safety (see the following
paragraph).
(5) The necessity for a multiple wedge solution may be eliminated if the
driving and resisting wedge forces are calculated using the minimum FS re-
quired. If Equation 4-12 is not satisfied for the FS required, a multiple
wedge solution will show the same results. If Equation 4-12 is satisfied, the
system has an FS equal to or greater than the minimum FS required.
4-16. Multiple Wedge Analysis.
a. Procedure.
(1) Divide the assumed sliding mass into a number of wedges, including a
single structural wedge, based on the configuration and discontinuities of the
backfill, wall proportions, and discontinuities of the foundation.
(2) Estimate the FS for the first trial.
(3) Compute the critical sliding angles for each wedge. For a driving
wedge, the critical angle is the angle that produces a maximum driving force.
For a resisting wedge, the critical angle is the angle that produces a minimum
resisting force.
(4) Compute the uplift pressures, if any, along the slip plane. The
effects of seepage should be included.
(5) Compute the weight of the wedges, including any water and surcharges.
(6) Compute the summation of the lateral forces for each wedge using the
general wedge equation. In certain cases where the loadings or wedge geome-
tries are complicated, the critical angles of the wedges may not be easily
calculated. The general wedge equation may be used to iterate and find the
critical angle of a wedge by varying the angle of the wedge to find a minimum
resisting or maximum driving force.
(7) Sum the lateral forces for all the wedges.
(8) If the sum of the lateral forces is negative, decrease the FS and
recompute the sum of the lateral forces. By decreasing the FS, a greater
4-25
EM 1110-2-2502
29 Sep 89
•H
iH
•H
rs CO
c
'(0
> (3
IÄ1
w O
o
o
X CO
W iH
CO
ii (=
cd
4)
•o
0)
&
s
9+©JOU<>3 r •H
CO
to
X «
W i—*
i—i
+ 1
St
8 u
(0 60
o •H
Ü fe
>
W
4-26
EM 1110-2-2502
29 Sep 89
percentage of the shearing strength along the slip planes is mobilized. If

the sum of the lateral forces is positive, increase the FS and recompute the
sum of the lateral forces. By increasing the FS, a smaller percentage of the
shearing strength is mobilized.
(9) Continue this trial-and-error process until the sum of the lateral
forces is approximately zero for the FS used. This will determine the FS that
causes the sliding mass to be in horizontal equilibrium.
(10) If the FS is less than the minimum required, redesign by widening or

sloping the base or by providing a key.
b. Computer Program. The computer program CSLIDE (Appendix O) can assist

in performing a multiple wedge sliding analysis.
4-17. Sliding Stability Criteria. The sliding stability criteria are given
in terms of a minimum factor of safety for the various loading conditions as
shown in Tables 4-1 through 4-3. Guidance on deep-seated sliding is given in
Chapter 5.
4-18. Design Considerations.
a. Effects of Cracks in Foundation. Sliding analyses should consider the

effects of cracks on the active side of the structural wedge in the foundation
material due to differential settlement, shrinkage, or joints in the rock
mass. The depth of cracking in cohesive foundation material with a plane
ground surface can be estimated with the following equations.
d
(«-M
= —^- = -^ tan 145° + ^) [4-13]
where
c, = c/FS
a
(j), = tan (tan (|>/FS)
y' , K (see Equation 3-11)
For sloping backfills see Appendix I. The value d in a cohesive foundation

and the depth of cracking in massive strong rock foundations should be assumed
to extend to the base of the structural wedge. The depth of cracking in a
level clay blanket should be computed using Equation 4-13. Full hydrostatic
pressure should be assumed to act at the bottom of the crack. The hydraulic
gradient across the base of the structural wedge should reflect the presence
of a crack at the heel of the structural wedge. Examples showing the calcula-
tion of d are found in Appendix N in examples 3, 4, 5, 6, and 7.
4-27
EM 1110-2-2502
29 Sep 89
b. Passive Resistance. When passive resistance is used, special con-

siderations must be made. Rock or soil that may be subjected to high velocity-
water scouring should not be used unless amply protected. Also, the compres-
sive strength of rock layers must be sufficient to develop the wedge resis-
tance. In some cases, wedge resistance should not be assumed without
resorting to special treatment, such as rock anchors.
Section V. Bearing Capacity Analysis
4-19. General Computations. The bearing capacity is checked for the same
loading conditions as determined by the overturning analysis for each case
analyzed. The bearing capacity should be checked along the same plane assumed
in the sliding analysis. A normal (N') and tangent (T) force are calculated
for the structural wedge along the assumed bearing plane. These forces are
shown in Figure 4-11. T and N' are used in combination to check the bear-
ing capacity. The bearing capacity analysis discussed in Chapter 5 and in the
CBEAR User's Guide (Mosher and Pace 1982) (see Appendix 0) considers both the
normal and tangent components of the resultant force at the base of the struc-
ture. The factor of safety against a bearing failure can be computed by
dividing the normal component of the ultimate bearing capacity by the effec-
tive normal force applied to the structural wedge as shown below:
FS = |r [4-14]
where
Q = normal component of the ultimate bearing capacity
N' = effective normal force applied to the structural wedge
The value computed from the general bearing capacity equation in Chapter 5 is
the bearing capacity normal to the base of the structure. The computer pro-
gram CBEAR (Appendix 0) can assist in performing a bearing capacity analysis.
Example calculations are shown in Appendix N.
4-20. Inadequate Bearing Capacity. If the factor of safety against bearing

failure is insufficient, consideration should be given to increasing the width
of the base, lowering the base of the wall, or founding the wall on piles.
4-21. Bearing Capacity Criteria. The criteria for bearing capacity are given
in terms of a factor of safety as defined in paragraph 4-19 and shown in
Tables 4-1 through 4-3.
Section VI. Summary of Design Procedures
4-22. Design Procedures. Figure 4-12 presents a summary of the design proce-
dures discussed in this chapter.
4-28
EM 1110-2-2502
29 Sep 89
SET GEOMETRY OF
STRUCTURAL «EDGE
COMPUTE MTER PRESSURES

INCLUDING SEEPAGE EFFECTS
COMPUTE LATERAL EARTH FORCES

FOR DRIVING HEDGES USING SMF» NOTEi
2/3 AND FOR RESISTING «EDGES FOR A »ALL WITH A
USING AT-REST EQUATION KEY. THE BASE SHOULD
BE SIZED FROM A
SLIDING ANALYSIS FIRST.
COMPUTE VERTICAL FORCES

FOR STRUCTURAL «EDGE
»DEN
BASE
PERFORM OVERTURNING ANALYSIS
FOR STRUCTURAL HEDGE
■NO-
CALCULATE DRIVING AND RESISTING

PERFORM SLIDING ANALYSIS FOR FORCES AS DISCUSSED IN PARAGRAPH
STRUCTURAL «EDGE USING SAME 4-BM510R PERFORM A MULTIPLE
LOADINGS AS FOR OVERTURNING HEDGE ANALYSIS
PROVIDE FOR GREATER

SLIDING RESISTANCE
PROVIDE FOR GREATER

BEARING RESISTANCE
PROCEED HITH STRUCTURAL DESIGN

USING SAME FORCES AS FOR OVERTURNING
Figure 4-12. Wall design flowchart
4-29
EM 1110-2-2502
29 Sep 89
CHAPTER 5
FOUNDATION ANALYSES
Section I. Bearing Capacity of Wall Foundations
5-1. Analysis Principles and Methods.
a. EM 1110-2-1903. A discussion of the principles and methods involved

in analyzing bearing capacity is contained in EM 1110-2-1903. The manual con-
cludes that Terzaghi's general bearing capacity equation, q = CN + wz N
+ WbN , is preferred. However, the manual does not address modifying the
general equation for effects of embedment, inclined loads, sloping bases,
passive-type wedges with sloping surfaces, overburden pressure, and eccentric
loads (moment-induced stresses), all of which are needed for computing the
bearing capacity of retaining and flood walls. The computer program CBEAR
(Appendix O) can assist in these computations.
b. Mode of Failure. The mode of failure depends on the relative com-

pressibility of the soil, loading conditions, and geometric considerations
(Vesic 1975). This manual is restricted to general shear failure of shallow
strip foundations, i.e., those whose widths are greater than their embedment.
A general shear failure normally exists for dense sand and stiff clay. How-
ever, for loose sand and soft clay, which may occur more frequently for flood
walls constructed in a flood plain, the bearing capacity should be computed
based upon local shear conditions (Vesic 1975).
c. Factor of Safety. The FS is calculated as follows:
*S = §r [5-1]
where
N' = effective normal force applied to the base of the structure
Q = normal component to the base of the structure of the ultimate

bearing capacity
The minimum acceptable bearing capacity factors for retaining walls and inland
and coastal flood walls are listed by loading case in Tables 4-1 through 4-3.
For each loading case, the same loadings as determined by the overturning
analysis should be used. Options to consider in the event of inadequate bear-
ing capacity have been presented in paragraph 4-20.
5-2. General Bearing Capacity Equation. The general bearing capacity equa-
tion for a strip footing is:
5-1
EM 1110-2-2502
29 Sep 89
(SdSigYtgY BYH )
Y
(? g [5-2]
cd?ci?Ct W +
< Vq±VqgqoV +
where
normal component of the ultimate bearing capacity of the

foundation
effective width of the base (B - 2e, as shown in

Figure 5-1)
width of the geometric base (as shown in Figure 5-1)
eccentricity of the load with respect to geometric base

width
c = cohesion parameter of the foundation
t, = factors as explained in paragraphs 5-4 through 5-8
N = bearing capacity factors for a strip load

c q
q = effective overburden pressure on the plane passing through
the base of the footing
Y = effective unit weight of the foundation material,

Y, below water table, v . ,_ above
buoyant moist
Figure 5-1 illustrates the meanings of all of the terms required to use the
information given in paragraphs 5-3 through 5-8. The general bearing capacity
equation is taken from the CBEAR user's guide (Mosher and Pace 1982) (see also
Appendix O). The appropriate soil foundation shear strength for retaining
walls and inland and coastal flood walls is listed, by loading case, in
Tables 4-1 through 4-3.
5-3. Bearing Capacity Factors. Bearing capacity factors for a horizontal

strip footing under vertical loading are:
Nq . [.<* tan «] tan2 £45. + |J [5-3a]
N - (N - 1) cot (when <f> > 0) [5-3b]

c q
or
5.14 (when $ = 0) [5-3c]
Ny = (N - 1) tan (1.4*) [5-3d]
5-2
EM 1110-2-2502
29 Sep 89
mm
PR D
T N'
Load Inclination, 6= tan"1 (j/N'J

Effective width B = B - 2e
a. Horizontal base
~%®m\ ~
^
wm r-^- I fjpÄr
b. Keyed base, sloping ground

Figure 5-1. Terms used in bearing capacity equation
5-3
EM 1110-2-2502
29 Sep 89
Bearing capacity factor values for § , ranging between 0 and 50 degrees, are
given in Table 5-1.
5-4. Embedment Factors. Embedment factors take into consideration the shear-
ing resistance along the foundation slip plane that exists in the soil above
the base of the footing, on the toe side of a wall. These factors can be
computed as:
tan
*cd - l + 0.2pM (*5° + f) [5-4a]
5 = 5 l (wheT1 =
qd Yd " * °0) [5 4b]
"
or
Cqd - C . - 1 + O-M-Z-) tan ^45° + f) (when <f > 10°) [5-4c]
When ty lies between 0 and 10 degrees, a linear interpolation can be made for
£ between 1 for (j) = 0°, and 1 + 0.1 (D/B) tan (45° + <|>/2) for <j> = 10° .
Embedment factors account for the shear strength above the base of the
footing. Their use may be unconservative if the shear strength does not
exist.
5-5. Inclination Factors. Inclination factors account for the effect of load
inclination for concentrically loaded foundations. They are computed as
follows:
Si - (i - f )2 [5 5kl
"
Where 8 is the angle that the line of action of the load makes with a line
drawn normal to the base. If 8 > <|> , % , should be set equal to zero.
5-4
EM 1110-2-2502
29 Sep 89
Table 5-1
Bearing Capacity Factors (CBEAR User's Guide)*
N N N tan2 \£5°+^)
_4 C a 7 tan (b
0 5.14 1.00 0.00 0.0000 1.0000

l 5.38 1.09 0.00 0.0175 1.0355
2 5.63 1.20 0.01 0.0349 1.0723
3 5.90 1.31 0.02 0.0524 1.1105
4 6.19 1.43 0.04 0.0699 1.1500
5 6.49 1.57 0.07 0.0875 1.1910

6 6.81 1.72 0.11 0.1051 1.2335
7 7.16 1.88 0.15 0.1228 1.2776
8 7.53 2.06 0.21 0.1405 1.3233
9 7.92 2.25 0.28 0.1584 1.3709
10 8.34 2.47 0.37 0.1763 1.4203

11 8.80 2.71 0.47 0.1944 1.4716
12 9.28 2.97 0.60 0.2126 1.5250
13 9.81 3.26 0.74 0.2309 1.5805
14 10.37 3.59 0.92 0.2493 1.6382
15 10.98 3.94 1.13 0.2679 1.6984

16 11.63 4.34 1.37 0.2867 1.7610
17 12.34 4.77 1.66 0.3057 1.8263
18 13.10 5.26 2.00 0.3249 1.8944
19 13.93 5.80 2.40 0.3443 1.9655
20 14.83 6.40 2.87 0.3640 2.0396

21 15.82 7.07 3.42 0.3839 2.1171
22 16.88 7.82 4.07 0.4040 2.1980
23 18.05 8.66 4.82 0.4245 2.2826
24 19.32 9.60 5.72 0.4452 2.3712
25 20.72 10.66 6.77 0.4663 2.4639

26 22.25 11.85 8.00 0.4877 2.5611
27 23.94 13.20 9.46 0.5095 2.6629
28 25.80 14.72 11.19 0.5317 2.7698
29 27.86 16.44 13.24 0.5543 2.8821
(Continued)
(Mosher and Pace 1982).
5-5
EM 1110-2-2502
29 Sep 89
Table 5-1 (Concluded)
N N N tan2 \L5°+^)
_i C a Y tan <t)
30 30.14 18.40 15.67 0.5774 3.0000

31 32.67 20.63 18.56 0.6009 3.1240
32 35.49 23.18 22.02 0.6249 3.2546
33 38.64 26.09 26.17 0.6494 3.3921
34 42.16 29.44 31.15 0.6745 3.5371
35 46.12 33.30 37.15 0.7002 3.6902

36 50.59 37.75 44.43 0.7265 3.8518
37 55.63 42.92 53.27 0.7536 4.0228
38 61.35 48.93 64.08 0.7813 4.2037
39 67.87 55.96 77.33 0.8098 4.3955
40 75.31 64.20 93.69 0.8391 4.5989

41 83.86 73.90 113.99 0.8693 4.8149
42 93.71 85.38 139.32 0.9004 5.0447
43 105.11 99.02 171.15 0.9325 5.2893
44 118.37 115.31 211.41 0.9657 5.5500
45 133.88 134.88 262.75 1.0000 5.8284

46 152.10 158.51 328.74 1.0355 6.1260
47 173.64 187.21 414.34 1.0724 6.4447
48 199.26 222.31 526.47 1.1106 6.7865
49 229.93 265.51 674.94 1.1504 7.1536
50 266.89 319.07 873.88 1.1918 7.5486
5-6
EM 1110-2-2502
29 Sep 89
5-6. Base Tilt Factors. These factors are used to take into account the
effect of a sloping base. The base tilt factors are computed as:
r = r = (1 - a tan A) (a in radians) [5-6a]

^qt yt
r - ! _ (_2« ) (0 in radians) (when * - 0°) [5-6b]
r = r 91- (when <j> > 0°) [5-6c]

*et *qt N tan f
where a is the angle the slip plane of the structural wedge makes with the
horizontal, measured in radians. The sign of a will follow the sign con-
vention given in Chapter 4.
5-7. Ground Slope Factors. Ground slope factors are used to correct for a
sloping ground surface on the toe side of the wall. The factors are computed
as:
2
C = £ = [1 - tan ($)] [5-7a]
Yg qg
E
s m l _ r 2ß 1 (ß in radians) (when <f> - 0°) [5-7b]
cg |_(ir + 2)J
N = -2 sin $ (when $ - 0°) [5-7c]

Y
1 - C
£
s
= r aS_ (when <t> > 0°) [5-7d]
cg qg Nc tan $
where ß is the angle the ground surface makes with the horizontal, measured
in radians. ß is positive when the ground slopes down and away from the
footing.
5-8. Effective Overburden Pressure, g is defined as the effective vertical

stress due to the soil and/or surface loads above the base of the footing, on
the toe side of the wall, as follows:
5-7
EM 1110-2-2502
29 Sep 89
qo - Y'D [5-8a]
where
y = effective unit weight of the overlying soil
D = depth from the soil surface to the base of the structural wedge
For the special case of a sloping surface, compute q as:
q = Y'D cos [ABS(8)] [5-8b]
5-9. Combination of Factors. As discussed in the CBEAR user's guide (Mosher

and Pace 1982), the correction factors for the load inclination, base tilt, and
ground slope and the adjustment for the load eccentricity should only be used
in unison when all of these factors tend to produce failure in the same
direction.
5-10. Example. Example problems using the general bearing capacity equation
are presented in Appendix N.
Section II. Other Considerations
5-11. Settlement.
a. EM 1110-2-1904. A discussion on the various factors involved in the

settlement of a structure, on methods for estimating settlements, and on the
limitations in the accuracy of conducting settlement analyses from laboratory
tests is contained in EM 1110-2-1904. The principles and methods presented are
applicable to a majority of civil works projects. Additional information for
unique or special projects can be obtained from various texts on soil
mechanics. The computer program CSETT (Appendix 0) can assist in performing a
settlement analysis.
b. Allowable Settlement. The maximum value of angular distortion

(settlement/length of structure) which can be tolerated without cracking of
reinforced concrete retaining walls is 0.002 to 0.003 radian (Duncan and
Buchignani 1976) .
5-12. Deep-Seated Sliding. A deep-seated sliding analysis should be performed

to check for sliding within weak layers which may exist beneath structures.
The analysis should be in accordance with procedures outlined in
paragraph 4-16. Active and passive wedges should be located a sufficient dis-
tance apart to allow a rotational slip surface to develop. Generally, a slip
plane inscribed in an arc with a radius equal to the height of the active wedge
will comply with this requirement (Figures 5-2 and 5-3). When the wall is
resting on thick strata of weak soils, shallow shear failure should be
5-8
EM 1110-2-2502
29 Sep 89
oi
0)
4-1
60
0)
■Ö
<4-t
o
0)
Ü
CO
M-i
(0
u
1-1
4J
01
>
to
•H
CO
>>
r-l
B)
C
cd
00
e
ai
4-1
at
a)
co
a
ai
O
I
m
ai
u
s
00
5-9
EM 1110-2-2502
29 Sep 89
0)
o
4J

•A
CO
►»
H
a)
§
bO
C
•H
■O
•rl
4)
4J
at
a>
to
I
a.
«
p
to
i
m
ai
M
S
00
5-10
EM 1110-2-2502
29 Sep 89
investigated. This may be assumed to occur below the base of the retaining or
flood wall along a cylindrical surface passing through the heel (Figure 5-4).
The minimum factor of safety, which must not be less than 1.5, is determined by
trial and error by changing the center of the trial circle.
Figure 5-4. Shallow shear surface
5-13. Liquefaction Susceptibility. Where walls are underlain by sands below

the water table in seismically active areas, an analysis should be made of the
safety against foundation liquefaction. Flood walls in alluvial valleys are
particularly likely to be situated over loose, saturated sands that may be
liguefiable. A preliminary assessment of liquefaction susceptibility can be
made using Seed's simplified method (Seed 1976, Seed and Idriss 1982) which is
based on the standard penetration test. If the foundation is found to be
non-liquefiable, no further analysis need be made. If liquefaction may occur,
an assessment should be made of the risks and consequences of liquefaction
failure and the benefits and costs of alleviating the risks. The occurrence
of an earthquake during a flood is a case of the joint occurrence of indepen-
dent rare events. For flood walls, the probability (risk) of an earthquake
during a flood will be much smaller than the probability during a non-flood
period, but the associated consequences may be much higher. For certain walls,
(e.g., a low retaining wall remote from other structures) the probability of
liquefaction failure and the related consequences may translate into such a
small risk that accepting the risk may be the preferred alternative. Possible
alternatives to dealing with potentially liquefiable foundations include:
a. Changing the proposed location (usually the best alternative, where

feasible).
5-11
EM 1110-2-2502
29 Sep 89
b. Removing and replacing the liquefiable materials.
c. Improving the liquefiable materials in place, by densification or

grouting.
d. Accepting the risks and consequences of liquefaction.
5-12
EM 1110-2-2502
29 Sep 89
CHAPTER 6
DESIGN AND CONSTRUCTION DETAILS AND CAUSES OF

UNSATISFACTORY PERFORMANCE
6-1. Foundation Preparation. Earth foundations should be properly compacted

and should be clean and damp before concrete is placed. Rock foundations
should be cleaned and given any other necessary treatment to ensure proper bond
of concrete to rock. Some rock foundations, primarily shales, require a
protective covering such as unreinforced concrete to protect them from dete-
rioration after being exposed and before concrete placement, unless the final
excavation can be performed close enough in time to the placement of the
structural base slab. When a protective coating is used, it must be such as to
ensure proper bond.
6-2. Concrete Materials. Consideration should be given to the materials that

are economically available for a particular project. EM 1110-2-2000 describes
concrete materials requirements; all options which are applicable to the work
and which include available materials should be investigated. Concrete pro-
portions should be selected to satisfy strength and durability requirements.
6-3. Constructabilitv. The dimensions of the wall should be such that rein-
forcement and concrete can be properly placed. EM 1110-2-2000 provides guid-
ance for concrete placement. Guide specifications CW 03301 and CW 03305
provide detail requirements for concrete placement. The top thickness of the
stem for cantilever concrete walls over 8 feet high and for base slabs should
be a minimum of 12 inches to facilitate concrete placement. Stems not over
8 feet high with one layer of vertical reinforcement may be 8 inches thick.
The wall section should be designed for simplicity and maximum reuse of forms.
Any construction constraints due to the location of the wall should be included
in the design.
6-4. Joints. Walls are designed with joints to allow for expansion, contrac-
tion, and/or to divide the structure into convenient working units. The loca-
tions of all horizontal and vertical joints should be shown on the drawings.
a. Expansion Joints.
(1) General Needs and Uses. Expansion joints are designed to prevent
the crushing and distortion (including displacement, buckling, and warping) of
the abutting concrete structural units that might otherwise occur due to the
transmission of compressive forces. Compressive forces may be developed by
expansion, applied loads, or differential movements arising from the configura-
tion of the structure or its settlement. In general, expansion joints are
needed to prevent spalling and sometimes to break continuity. In relatively
thin reinforced concrete walls such joints should be located where consider-
able expansion or unequal settlement is anticipated, e.g., at changes in
alignment or grade, at abrupt changes in section or at intermediate points
when needed. In massive reinforced concrete walls and in gravity walls on
rock, expansion joints usually are not provided unless required at abrupt
6-1
EM 1110-2-2502
29 Sep 89
changes in section or at angle monoliths to relieve thrust from expected ex-

pansion. Otherwise, adequate chamfers on each side of each contraction joint
usually are sufficient to prevent spalling. Where temperature variations are
extreme, modification of these criteria may be required. Reinforcing steel,
corner protection angles, and other fixed metal embedded in or bonded to the
surface of the concrete should not extend through an expansion joint. Where
water tightness is needed, water stops are provided as outlined in
paragraph 6-4e.
(2) Joint Filler. The thickness of joint filler necessary to provide

stress relief at a joint should be determined from the estimated initial con-
traction and subsequent expansion from maximum temperature variation. Pre-
molded expansion joint filler and adequate chamfers should be used.
b. Contraction (Monolith) Joints. These are intentional planes of weak-

ness designed to regulate cracking that might otherwise occur due to the un-
avoidable, often unpredictable, contraction of concrete structural units.
Contraction joints also divide the structure into convenient working units and
thus also serve as construction joints. Since it is impractical and uneconom-
ical to provide sufficient reinforcement to prevent cracks entirely, it is
desirable to control their location, insofar as is practicable, by vertical
contraction joints, across which reinforcement does not extend. No exact rules
for the location of such joints can be made. Each job must be studied to
determine where the joints should be placed, taking into account the re-
quirements of structural design, the volume of concrete which can be placed
economically in a single working unit, and the economical use of form units.
Typically, contraction joints have been spaced 20 to 30 feet apart. Usually, a
contraction joint has a plane surface without a key. For cantilever concrete
walls, vertical contraction joints may be located only in the stem, and the
footing may be a continuous placement.
c. Horizontal Construction Joints. These joints are provided to divide a

wall into convenient working units, but they should be kept to a minimum. Keys
are not permitted in horizontal construction joints as they interfere with good
cleanup of the concrete surface and because a well-bonded flat surface is more
dependable to transfer shear.
(1) Gravity Concrete Walls. For this type of wall the horizontal con-
struction joint locations are dictated by the height of each lift of concrete
placement. Concrete for gravity walls is usually placed in lifts up to 10 feet
high. The top surface of each lift is cleaned and roughened by high-pressure
water jets before placing the next lift.
(2) Cantilever Concrete Walls. For this type of wall a construction

joint between the base and the wall stem should be provided. Additional hori-
zontal joints in the wall stem should be provided by lifts approximately
10 feet high. The surface of each joint should be roughened to obtain as much
shear strength across the joint as possible.
6-2
EM 1110-2-2502
29 Sep 89
d. Joint Details for Flood Walls. For expansion and contraction joint
details for flood walls, see paragraph 7-14.
e. Water Stops. Water stops are provided across joints where water-
tightness is required. Nonmetallic water stops, such as rubber or polyvinyl
chloride (PVC) water stops, should be used in accordance with EM 1110-2-2102.
For special flood wall water stop details, see Chapter 7, Sections II and V.
Careful inspection is required for water stop installation, especially with the
type "U" water stop (Figure 7-9b), to see that special reinforcing is properly
placed and that concrete is placed under the upper water stop in the base slab.
6-5. Soil Backfill.
a. Material Choice. Many types of material can be used for backfill. It

is advisable to use locally available material when possible. Unusually poor
foundation material or a need to control piping may require importation of
select material.
b. Materials. Clean sands and gravels are the most suitable materials.
They drain rapidly, are not susceptible to frost action, and remain stable.
Silty sands, silts, and coarse-grained soils containing some clay are less
desirable since they drain slowly, are subject to seasonal volume changes, and
may lose much of their strength with time. Shrinkage cracks may develop in
clay which, when filled with water, can cause full hydrostatic pressures to act
on the wall. As mentioned in paragraph 6-7, clay, as backfill or foundation
material, is involved in most retaining wall failures. During winter
construction, frozen backfill material should not be used under any circum-
stances. This material may appear satisfactory when put into place, but it can
be adversely affected when it thaws.
c. Placing and Compacting. (Refer to Chapter 3 and Appendix J for addi-

tional information on compaction.) The backfill material should be carefully
selected. It should be compacted to prevent large settlements due to its own
weight, with the amount of compaction required depending on the material used
and the purpose of the structure. Very strict control of compaction is re-
quired when the fill is a cohesive soil. When granular fill is used, the mate-
rial should be placed in thin lifts with each lift being compacted before the
next lift is placed (see EM 1110-2-1911) . However, precautions should be taken
to prevent overcompaction which will cause excessive lateral forces to be
applied on the structure. If heavy compaction rollers are used near the wall,
their effect on lateral earth pressures on the wall should be considered in the
design. Alternatively, the allowable weight of compactors may be restricted by
the specifications to control wall pressures. It is good practice to place a
layer of impervious soil that is a minimum of 12 inches thick in the upper lift
of the backfill to reduce infiltration of rainwater. Backfill should be
brought up equally on both sides until the lower side finished grade is
reached.
6-3
EM 1110-2-2502
29 Sep 89
6-6. Drainage.
a. Need for Drainage System. As mentioned in paragraph 6-7, improper

drainage systems are one of the major causes of retaining wall failures.
Drainage systems are necessary to eliminate excess hydrostatic pressures on the
failure plane and the wall stem due to water seepage and surface infiltration
of rainfall. In some cases the drainage system may be needed to prevent
pressures from building up due to frost action in the backfill or to minimize
pressures due to swelling of cohesive backfills. The kind of drainage system
required depends upon the type of soil backfill, amount of rainfall, ground-
water conditions, and potential frost action. Regardless of the drainage sys-
tem used, the wall must have an adequate factor of safety assuming the drainage
system is inoperative (see paragraph 3-23) .
b. Drainage Control Methods. All retaining walls must have adequate

surface drainage to dispose of surface water. As previously mentioned, a layer
of impervious soil should be placed on top of the soil backfill to reduce
surface infiltration of rainfall. The most effective way to control drainage
within the soil backfill is an inclined drainage blanket with longitudinal
drain as shown in Figure 6-1. The inclined drainage blanket will
GUTTER ■
IMPERVIOUS LAYER
IMPERVIOUS FILL
NOT TO SCALE
Figure 6-1. Inclined drainage blanket (after Department of the Navy 1982a)
6-4
EM 1110-2-2502
29 Sep 89
minimize excess hydrostatic pressures on the failure plane due to groundwater

seepage and surface infiltration of rainfall. A drain adjacent to the wall is
less effective and will often result in higher loads against the wall (see
Figure 6-2) . However, for relatively low walls (typically less than 10 feet
high), these higher loads may not be significant, and drains adjacent to the
wall are often used. Drains adjacent to the wall may be either a drainage
blanket (Figure 6-3) or a prefabricated drainage composite* (Figure 6-4).
Where frost penetration is a problem, a drainage system as shown in Figure 6-5
should be used. If a cohesive soil backfill is used, a drainage system as
shown in Figure 6-6 will prevent changes in moisture content of the clay and
hence reduce cracking and swelling potential. Other seepage control methods
are discussed in paragraph 7-4.
c. Longitudinal Drains. Longitudinal drains within drainage blankets are

used for carrying the discharge from behind the retaining wall to a ditch,
manhole, or other free exit. Drains should be large enough to carry the
discharge and have adequate slope to provide sufficient velocity to remove
sediment from the drain.** To minimize clogging, the drain should have
perforations in the bottom half of the pipe at least 22.5 degrees below the
horizontal axis. Where the operation of the drains is counted on to reduce the
design loadings, manholes and/or inspection holes (see Figure 6-7) should be
located at sufficient intervals, and at any sharp bends in the pipe, to
facilitate inspection and cleanout. The terminus of the drain should have a
vertical check valve (see Figure 6-8) to prevent backflooding. The end section
of pipe supporting the check valve should be secured with a coupling band which
can be removed for inspection and cleaning of the pipe.
d. Weepholes. Weepholes should consist of a pipe, at least 3 inches in

diameter, extending through the stem of the wall. They should be protected
against clogging by pockets of gravel in the soil backfill or by the use of
filter fabric adjacent to the wall directly behind the weepholes. The weep-
holes are commonly spaced not more than 10 feet apart vertically and
horizontally.
e. Filter Requirements. Drains should be adequately protected by filter

layers so that seepage water is admitted freely but movement of the soil back-
fill into the drain will not occur. The piping or stability criterion is
Whenever a prefabricated drainage composite is used adjacent to the re-

taining wall, the crushing strength of the prefabricated drainage
composite should be greater than three times the maximum lateral earth
pressure acting on the wall. Prefabricated drainage composites are not
recommended for inclined drains due to possible damage during compaction
of the soil backfill and possible sliding along the plane of the drain
(Smith and Kraemer 1987, Kraemer and Smith 1986).
For a 6-inch-diameter pipe the minimum slope would be about 0.15 percent
(Schwab et al. 1981) .
6-5
EM 1110-2-2502
29 Sep 89
POTENTIAL FAILURE PLANE
EATlC SURFACE
WATER PRESSURE
DISTRIBUTION ON
POTENTIAL FAILURE
PLANE DUE TO
STEADY SEEPAGE.
(a) NORMAL STEADY STATE SEEPAGE CONDITION (VERTICAL DRAIN)

POTENTIAL FAILURE PLANE.
INFILTRATION
1 t t
NOTE INCREASE IN
WATER PRESSURE ON
POTENTIAL FAILURE
PLANE DUE TO
SURFACE INFILTRATION.
(b) SURFACE INFILTRATION (VERTICAL DRAIN)
INFIL TRA TION ^POTENTIAL FAILURE PLANE

\ \ \ S
—i—i—i yi—i-
NOTE WATER PRESSURE

IS ZERO ON POTENTIAL
FAILURE PLANE.
(c) SURFACE INFILTRATION (INCLINED DRAIN)

Figure 6-2. Effect of drain location on excess hydrostatic pressures on
the failure plane (after Geotechnical Control Office 1982)
6-6
EM 1110-2-2502
29 Sep 89
^STODRAW
IMPERVIOUS BACKFILL;
EXCAVATION LINE
DRAINAGE BLANKET
CLEAN COA RSE SAND •
CLEAN GRA VEL BASE^
LATERAL SUBDRAIN LINE

CLEAN
COARSE GRAVEL
NOT TO SCALE
Figure 6-3. Drainage blanket located adjacent to retaining wall

(after Sibley 1967)
6-7
EM 1110-2-2502
29 Sep 89
'2"FABRIC FLAP WRAPPING

PIPE AND CORE EDGE
Figure 6-4. Prefabricated drainage composite used as drain adjacent to

retaining wall (adapted from Carrol and Murphy 1985)
FROST
12" MIN FILTER

OR FILTER FABRIC
LONGITUDINAL
DRAIN
NOT TO SCALE
Figure 6-5. Drainage system to prevent frost penetration behind

retaining wall (after Department of the Navy 1982a)
6-8
EM 1110-2-2502
29 Sep 89
PERMANENTLY
DRAINED CLAY
BACKFILL
NOT TO SCALE
Figure 6-6. Drainage system to use with clay backfill
(after Terzaghi and Peck 1948)
6-9
EM 1110-2-2502
29 Sep 89
CM. TEE
8-DIA
PERFC.M.P.
8"DIA
PERFCMP.
21-OIA
CORR METAL PIPE
GUARD POST
GALVSTDPIPE
PAINT YELLOW
SAND OUTER
FILTER
GRAVEL INNER
FILTER
PERFORATED PIPE
FOR SUBDRAINAGE
SYSTEM
NOT TO SCALE
Figure 6-7. Inspection hole for longitudinal drain
6-10
EM 1110-2-2502
29 Sep 89
CHECK VALVE
MANHOLE WALL
ALUMINUM l
GRAVEL FILTER
i8"PERFA.C.P.
NOT TO SCALE
TYPICAL VERTICAL CHECK VALVE SEAT
Figure 6-8. Vertical check valve at end of longitudinal drain
based on the grain size relationship between the protected soil and the filter
D
15,
D * 5 [6-1]
85,
where
D = size of filter material at 15 percent passing

15
F
D = size of protected soil at 85 percent passing
85
B
6-11
EM 1110-2- 2502
29 Sep 89
and
1 25
IT"
50
* [6-2]
B
where
H = size of filter mater ial at 50 percent passing
= size of protected soil at 50 percent passing

"».
To assure that the filter material is more permeable than the material being
drained, the following condition must be met:
D
15T
* 5 [6-3]
15T
To prevent clogging of perforated longitudinal drains, the following require-

ment must be satisfied:
Circular openings
50T
Hole diameter * 1.0 [6-4]
Slotted openings
50T
1.2 [6-5]
Slot width
The filter material may satisfy the criteria for stability and permeability
but may be too fine to meet the criteria for circular or slotted openings.
Should this happen, multilayered or graded filters are required. It may be
possible to substitute filter fabric for one or more of the granular filters
in a multilayered filter system. Filter cloth shall conform to the
6-12
EM 1110-2-2502
29 Sep 89
requirements of guide specification CW 02215.
f. Drain Requirements. The drain must be able to carry the design flow
freely without movement of soil particles. Drainage blankets may be con-
structed of clean sand and gravel or a prefabricated drainage composite (for
certain applications). The design flow can be determined from a flow net
(Cedergren 1967). For isotropic soil conditions:
n
f [6 6]
% - V IT Q
"
where
q = quantity of discharge through soil backfill per linear foot of

retaining wall
k = permeability of soil backfill
h = hydrostatic head acting on retaining wall
n = number of flow channels in flow net
n, = number of equipotential drops in flow net

d
The minimum required permeability of the drain is
k,d - 7-f— [6-7]

Vd
where
k., = minimum required permeability of the drain

a
q = quantity of discharge through drainage blanket or prefabricated
drainage composite per linear foot of retaining wall
i = gradient of flow in the drain (1 for vertical drain, equal to slope

of drain for inclined drain)
A, = cross-sectional flow area of drain

d
Seepage in coarse aggregates may be turbulent and a reduction factor should be
applied to the permeability as shown in Figure 6-9. The in-place permeability
6-13
EM 1110-2-2502
29 Sep 89
T 1
0.025--
LIMITING ENVELOPE
COMPLETE TURBULENCE
J_ I J_ I X ±
o.i 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0
HYDRAULIC GRADIENT i
Figure 6-9. Approximation for estimating reduction in permeability of

narrow size-ranged aggregate caused by turbulent flow
(Cedergren 1967, courtesy of John Wiley and Sons)
should be at least 20 times that calculated theoretically. For prefabricated

drainage composites the in-plane permeability will decrease with increase in
lateral pressure. Therefore, the in-plane permeability must be taken at the
maximum lateral earth pressure acting on the wall.
g. Construction Considerations.
(1) Sand and Gravel. Sand and gravel must not become segregated or
contaminated prior to, during, or after installation. Segregation will result
in zones of material too fine to meet the permeability requirements and other
zones too coarse to meet the stability requirements. Contamination of the
filter material from muddy water, dust, etc., during construction may clog the
voids in the material and prevent proper drainage. In the event that filter or
drain materials are contaminated, they should be replaced. Filter materials
subject to cementation should be rejected.
(2) Prefabricated Drainage Composite. Special consideration should be

given when compacting soil backfill near prefabricated drainage composites
adjacent to retaining walls. Compaction adjacent to the retaining wall will
induce high lateral pressures which could crush the prefabricated drainage
6-14
EM 1110-2-2502
29 Sep 89
composite and/or reduce the inplane permeability. The drainage composite

manufacture's recommendations for backfilling and compaction near the composite
should be followed. A test section may be required to determine the acceptable
operating conditions of the compaction equipment. Where crushed stone is used
as the backfill material, a blanket of sand should be provided against the
drainage composite to protect it against damage during compaction.
(3) Longitudinal Drains. One bad joint could render an entire drainage
system inoperative. Care must be taken in compacting soil backfill over drains
to prevent crushing of the pipe. Differential settlement can cause pipe joints
to open up, permitting soil backfill to infiltrate. This should be minimized
by attaining uniform adequate compaction of the underlying material.
6-7
• Causes of Unsatisfactory Performance. The results of two statistical
studies of retaining wall failures are given in Figure 6-10 (Tcheng and Iseux
1972, Ireland 1964). It is evident that:
a. Clay, as backfill or foundation material, is involved in most retain-

ing wall failures.
b. Improper design of the drainage system and/or the wall base is the
main cause of retaining wall failure.
6-15
EM 1110-2-2502
29 Sep 89
UNSATISFACTORY DIMENSIONING
Of WALL BASE
MISSING OR INADEQUATE
DRAINAGE SYSTEM
COULD NOT BE
CLASSIFIED
CARELESS
CONSTRUCTION
STRUCTURAL FAILURE
FAULTY BACKFILLING OF STEM
a. Causes of failure of rigid concrete retaining walls

(Techeng and Iseux 1972)
BACKFILL UNKNOWN
FOUNDATION: UNKNOWN
BACKFILL: CLAY
FOUNDATION: CLAY
BACKFILL: CLAY
FOUNDATION: SAND,
GRAVEL, ROCK
BACKFILL: UNKNOWN
FOUNDATION: CLAY
■BACKFILL: SAND, GRAVEL
FOUNDATION: CLAY
b. Foundation and backfill material of unsatisfactory

retaining walls (Ireland 1964)
Figure 6-10. Summary of experience with unsatisfactory retaining
walls
6-16
EM 1110-2-2502
29 Sep 89
CHAPTER 7
SPECIAL CONSIDERATIONS FOR FLOOD WALLS
Section I. General Characteristics
7-1. Introduction. The principal function of a flood wall is to prevent

flooding (inundation) of adjacent land. A flood wall is subject to hydraulic
loading on one side which is resisted by little or no earth loading on the
other side. The two principal types of flood walls are inland and coastal.
Inland flood walls typically are installed along a riverbank and are subjected
to design loadings (pool to freeboard line) for periods of hours or days
(long-term loadings). Coastal flood walls are primarily subjected to short-
term loadings (waves from hurricanes along with wind/tide high water surges).
The wave loadings are dynamic in nature and act upon the structure for only a
few seconds each. Concurrent high winds can prevent any emergency maintenance
during a storm. Utility line crossings through a flood wall require careful
attention to allow for independent movement of the utility lines and the wall,
which requires special expansion joint details.
7-2. Rationale for Loading Cases.
a. Design Water Level.
(1) The hydraulic data required for determining the design water level
should be listed in the hydrologic/hydraulic appendix of the pertinent planning
document for the project. The flow characteristics noted in historical records
and indicated from detailed observation of existing conditions will usually be
basic to the design of inland flood walls. Coastal flood walls will frequently
require hurricane surge simulation studies and wave setup estimates. Wave
overtopping can cause severe scour at or near the protected side of the stem.
See paragraph 3-24 for information on surge and wave loads.
(2) Factors that influence the water surface profile and level of pro-
tection, and that can reasonably be quantified, are included in the design
water level; not the freeboard. Some examples of these factors are:
(a) Changed conveyance, due to changing bed form, sedimentation or scour,

and vegetation growth or removal.
(b) Dynamic surges, and super elevation.
(c) Ice, debris, and local anomalies.
(d) Transverse slope due to water flowing out of or into the channel or
differences in velocity head between the channel and overbank locations.
(e) Profile instabilities associated with braids, meanders, etc.
7-1
EM 1110-2-2502
29 Sep 89
(f) Energy losses due to changing flow area, e.g. constrictions

(bridges), abrupt expansions, and bends.
(g) Future changes in flood flows due to changes in the watershed.
b. Freeboard. The freeboard is the marginal height of wall provided

above the design water level. Freeboard is designed to accomplish design
objectives and allow for uncertainty in a water surface profile.
(1) Examples of design objectives are:
(a) Assurance of initial overtopping at the most desirable (least haz-

ardous) location.
(b) Reduced volume of wave overtopping.
(c) Extension of interval between major maintenance such as removal of

sediment deposition.
(2) Freeboard allowances for water surface uncertainty are allowances

that are not otherwise specifically accounted for because they are considered
too small to require specific determination or because they are too intractable
to be quantified. Those factors that influence the water surface profile, and
level of protection, and that can reasonably be quantified are included in the
design water level; not the freeboard.
(3) Wall settlement is identified as a separate increment added to the

wall height for that purpose and is not included in the freeboard.
(4) Freeboard design should be refined as a study progresses and not left
entirely to a detailed design phase. The amount of effort and corresponding
refinement for a given phase is a function of the importance and cost of
freeboard relative to the overall plan. For an early reconnaissance phase it
will generally be satisfactory to use quickly estimated freeboard values of
generally accepted default values. Default values of 2 feet on agricultural
and 3 feet on urban flood walls have been generally accepted. As the study
progresses, these early estimated or default values will be replaced by values
arrived at by a design process.
(5) When large non-breaking waves are normal incident to the stem of the
flood wall, the amount of freeboard will be determined by the amount of over-
topping allowed. It is important to remember that such overtopping can cause
significant scour on the protected (toe) side of the wall. This potential for
scour can require rigid paving within a 20- to 30-foot area of the wall.
7-2
EM 1110-2-2502
2 9 Sep 89
c. Loading Cases. For determining water and soil loads acting on flood
walls, refer to Chapter 3. Section I of Chapter 4 discusses loading cases.
Section II. Seepage Control
7-3. General Considerations. Water-retaining structures are subject to

through-seepage, underseepage, and seepage around their sides or ends. Seepage
control is a primary consideration of flood wall design. Uncontrolled seepage
may result in water pressures and uplift forces on the wall base in excess of
design assumptions and consequent structural instability. Excessive porewater
pressures in foundation materials near the landside toe of a wall may create
"quick" conditions evidenced by sand boils or heaving. Emerging seepage may
have sufficient velocity to move cohesionless foundation materials and erode
the wall foundation (piping). Seepage control entails the design of measures
to ensure that seepage pressures and velocities are maintained below tolerable
values. Properly controlled seepage, even if quantities are large, presents no
hazard. Since flood walls are often built in congested areas, it is often
necessary to pump seepage out of the protected area. While the seepage
quantity is often small compared to other sources, it is occasionally
appropriate to consider seepage control measures for the purpose of reducing
seepage quantities. Inadequate seepage control, as shown by one example in
Figure 7-1, may jeopardize the stability of a flood wall. In flood walls,
control of through-seepage is provided for by water stops (paragraph 7-13).
Seepage around the wall is controlled by specially designed and constructed
levee wrap-around sections (paragraph 7-12). Flood walls are usually provided
with a toe drain to control local underseepage along the flood wall base, as
shown in Figure 7-2. As flood walls are usually founded on alluvial materials,
pervious zones of significant thickness are often present at some depth below
relatively impervious top stratum materials and may be hydraulically connected
to the river. Because of the horizontal stratification of alluvial deposits,
the horizontal permeability may be greatly in excess of the vertical perme-
ability. The combination of these conditions may allow seepage to be readily
conducted landward beneath the flood wall. Where flood walls are underlain by
such pervious strata (the usual case), analysis may indicate the need for
underseepage controls in addition to the toe drain. Underseepage control mea-
sures vary because the selection and design of an appropriate control scheme is
highly dependent on site-specific conditions, particularly the stratification
and permeability of foundation materials, availability of right-of-way, and
local construction practices and costs. Various types of underseepage control
measures are discussed in paragraph 7-4.
7-4. Underseepage Control. The focus of underseepage analysis is to calculate

the expected exit gradient at the landside toe of a levee or flood wall and
compare its value to a theoretically critical value, the critical gradient
(typically 0.8 to 1.0). To provide some conservatism, underseepage controls
are provided where the calculated gradient exceeds an allowable gradient,
typically 0.5 to 0.8. For calculating the exit gradient, assessing the need
for underseepage controls, and designing such controls, the foundation condi-
tions are normally assumed to be a two-layer system consisting of a relatively
impervious top stratum overlying a pervious substratum. Detailed analysis
7-3
EM 1110-2-2502
29 Sep 89
EXPLODED VIEW OF FLDV DF WATER

ARDUND VATER STOP IN JOINT BETWEEN
PROTOTYPE FLODD WALL MONDLITHS -
WATER STOP BURIED IN INTERIOR OF
CONCRETE
PATH OF FLOWING WATER
Figure 7-1. Flow around interior embedded water stop in the base
7-4
EM 1110-2-2502
29 Sep 89
Water Side Land Side
Ground Line
-Toe
Drain
Heel —H K Toe
Base Width
■Sheet Pile
Cutoff (Optional)
2-6"
Sand & Gravel
6 0 Pipe Perforated
on Bottom Half —
Figure 7-2. T-type flood wall--horizontal base
7-5
EM 1110-2-2502
29 Sep 89
procedures are contained in EM 1110-2-1913 and WES Technical Memorandum 3-424

(US Army Engineer Waterways Experiment Station, 1956). In some instances,
where complex problems of geometry, anisotropy, and foundation layering exist,
flow nets and/or finite element seepage analyses may be necessary. Types of
underseepage control measures are described in the following paragraphs.
Additional discussion is given in paragraphs 3-23 and 6-6.
a. Cutoffs. A cutoff penetrating the pervious stratum beneath the wall

is the most positive means of controlling seepage. A cutoff can consist of an
excavated trench backfilled with impervious compacted earth, a slurry trench,
an extension of a concrete shear key, or a sheet pile wall. A cutoff is
usually located at the end of the wall footing on the unprotected (heel) side.
A cutoff must penetrate approximately 95 percent or more of the pervious strata
before significant reductions in the quantity of flow can be realized; however,
partial cutoffs can be somewhat effective in reducing uplift pressures on the
wall base. Deep cutoffs will often interfere with the normal exchange of
groundwater between an aquifer and a river during non-flood periods and should
only be considered where detailed hydrogeologic studies have been made in this
regard. The decision as to the type and depth of a cutoff should be based on
an underseepage analysis considering actual site conditions. A steel sheet
pile cutoff is not entirely watertight due to leakage at the interlocks but can
significantly reduce the possibility of piping of coarse-grained material in
the foundation. The effectiveness of a properly interlocked steel sheet pile
cutoff through a coarse-grained stratum in reducing uplift can be assumed to be
up to 50 percent. The design uplift diagram, as shown in Figure 7-3, should be
drawn with a pressure head at point B on the unprotected side of the the cutoff
equal to the full head of water on the unprotected side (neglecting any reduc-
tion in pressure due to head loss from seepage effects). The pressure head on
the protected side of the cutoff at point B should equal the pressure at
point B reduced by up to 50 percent of the difference between the full head
value on the unprotected side and the pressure head at the end of the toe of
the wall. The pressure head at the toe of the wall can be computed based on
the seepage path from the cutoff wall to the saturated level on the protected
side. If the effectiveness of the steel sheet pile cutoff is assumed to be
greater than 50 percent, it should be based on actual experience of similar
conditions and justified accordingly. An example of a flood wall with a sheet
pile cutoff is shown in example 5 of Appendix N. A sheet pile cutoff is less
effective in fine-grained material than in coarse-grained material because
cohesion may allow cracking and separation of the soil away from the sheet
pile. Bearing value of steel sheet piling should be neglected.
b. Toe Drains. All inland flood walls should be provided with a land-
side toe drain similar to that shown in Figure 7-2. Coastal flood walls
should be analyzed to determine if such drains are needed. The toe drain,
which runs parallel to the wall at the landside edge of the footing, provides
a positive outlet for local underseepage and a check for controlling piping
and/or excessive uplift pressure beneath the base slab. For walls on impervi-
ous foundations, the toe drain may be adequate to control all underseepage; for
walls on pervious foundations, additional seepage control measures will
7-6
EM 1110-2-2502
29 Sep 89
Cutoff
Datum e 0.0
mm /mm
Total head at B = EIA.

Pressure head at B = EIA. - EIB
Pressure head at B' =
(EIA.- EIB)- 0.5 [(Pressure head at B) - (Pressure head at C)]
( EI I_ EI }
Total head at C = EID+E-Q^-] A D
Pressure head at C = Total head at C - Elc
Figure 7-3. Uplift pressures for a wall with a sheet pile cutoff
7-7
EM 1110-2-2502
29 Sep 89
usually be required. In the case of pile-founded walls, the toe drain should
be adequate to protect against "roofing," the loss of material from beneath the
wall base. The drain should never be located under the wall footing, in order
to allow maintenance access and to avoid crushing the drain. A typical toe
drain design will consist of a 6- to 8-inch-diameter pipe perforated on the
bottom half and surrounded in all directions with 6 to 10 inches of filter
material designed by the filter criteria in paragraph 6-6e. The collected
water is usually disposed of by gravity outlets into ditches, ponding areas, or
pump stations. The toe drain system should provide access for inspection and
maintenance at changes in alignment and at intervals not to exceed 500 feet.
Discharge pipes should be provided with check valves that will prevent the
entrance of surface water.
c. Trench Drains. Where the impervious top stratum is thin or non-

existent, a trench drain may be used to control underseepage in the vicinity of
the flood wall toe. A trench drain is an enlarged variation of a toe drain.
It extends from the ground surface through shallow pervious layers or into a
pervious layer underlying a shallow surface blanket. The practical depth for
construction of a trench drain depends on available excavation equipment and
site dewatering requirements. The excavation, pipe placement, and backfilling
of the trench should always be performed in the dry. To assure adequate
capacity, the collector pipe should be sized considerably larger than computa-
tions indicate to be necessary. Backfill in a trench drain should conform to
the filter criteria in paragraph 6-6e. A trench drain should be provided with
inspection and maintenance access and backflow protection as described for toe
drains. The seepage calculations for the quantity of flow should assume the
tailwater elevation equal to that of the discharge of the trench drain.
However, if water can pond on the landside of the wall, the calculations for
uplift pressure should check whether a more critical uplift condition can occur
for the ponded case.
d. Relief Wells. Pressure relief wells are used to reduce uplift pres-
sures at depths in pervious layers which might otherwise cause sand boils and
piping of foundation materials. Wells function to some extent as a controlled
sand boil, relieving pressure by discharging water, but retaining materials
with a screen and filter. Wells are advantageous where pervious strata are
relatively thick or relatively deep. They are particularly useful in con-
trolling large quantities of seepage in strata of pervious material having
direct connections with the river. Another advantage of relief wells is the
ease with which they can be constructed if piezometric pressures measured
during high water indicate the need for additional underseepage control.
Design of relief well systems is described in EM 1110-2-1905, EM 1110-2-1901,
and WES Technical Memorandum 3-424 (US Army Engineer Waterways Experiment
Station, 1956) . The design entails selecting a spacing, size, and penetration
for a line of wells that will result in acceptable gradients at points midway
between the line of wells and at the flood wall toe. Relief wells are usually
not very effective in intercepting near-surface seepage, and it is often wise
to use them in combination with a toe drain. Relief wells should be pump-
tested when installed. Because the efficiency of relief wells may deteriorate
with time due to corrosion or bacterial incrustation, considerable monitoring
7-8
EM 1110-2-2502
29 Sep 89
and maintenance may be required to assure that the relief well system performs
acceptably for the project life. To assess possible well deterioration, a
representative number of wells should be periodically pump-tested, and the
specific capacity (flow/drawdown) should be compared to the initial pump test
results. To calculate uplift pressures on the wall, the potential head at the
well line should be assumed equal to the average head in the plane of wells, a
value obtained as part of the well design procedure in the cited references.
e. Riverside Impervious Blankets. Impervious riverside blankets (natural

or constructed) overlying a pervious foundation are effective in reducing the
quantity of seepage and to some extent are effective in reducing uplift
pressures and gradients landside of the flood wall. Their effects may be
analyzed using seepage analysis methods found in EM 1110-2-1913 and WES
Technical Memorandum 3-424 (US Army Engineer Waterways Experiment Station,
1956) . Riverside blankets may be constructed over thin natural impervious
blankets to improve the effects of the natural blankets or they may be con-
structed directly on pervious material. Excessively steep riverbanks may make
blanket construction impractical. Also, it is seldom feasible to construct
blankets over exposed portions of the pervious layer under water. A noncon-
tinuous blanket has serious drawbacks, as only a small area of pervious stratum
left exposed may significantly reduce the blanket's effectiveness. Riverside
impervious blankets need to overlap the riverside base of the flood wall to
minimize the potential for rupture of the blanket by landward deflection of the
flood wall when loaded. Riverside impervious blankets may be subject to scour
at high river stages when they would be most needed, or may crack open if not
continuously wet. To prevent such action, blankets should be protected imme-
diately after construction. A well-designed and well-planted vegetative cover
is ordinarily sufficient along straight reaches. Along outside curves of the
river, the blankets should be protected with riprap or other positive
protection.
f. Landside Seepage Berms. Landside seepage berms function by providing

an increased landside top blanket thickness, thereby reducing the gradient.
The berm also extends the seepage path by forcing the seepage exit landward.
Seepage berms are typically 100 to 300 feet wide. As flood walls are usually
built in areas where right-of-way cost or availability is insufficient for
levee construction, seepage berms are rarely used in conjunction with flood
walls. Procedures for seepage berm design are presented in WES Technical
Memorandum 3-424 (US Army Engineer Waterways Experiment Station, 1956) and
EM 1110-2-1913.
g. Grouting of Open Rock Joints. In cases where rock is shallow enough

that flood walls can be founded directly on the rock, close examination of the
rock surface is necessary to determine if open joints are present. Such joints
can be detrimental to uhderseepage control and should be cleaned out and filled
with grout before the concrete base is placed. If the possibility exists for
seepage flow through porous or cavernous rock in the foundation, consideration
should be given to installing a grout curtain.
7-9
EM 1110-2-2502
29 Sep 89
Section III. Foundation Considerations
7-5. Base Types. The T-wall is the most widely used flood wall type. T-walls
are normally constructed with horizontal or sloped bases. The advantages of
each type of base are as follows:
a. Horizontal Base (Figure 7-2).
(1) The volume of foundation excavation is usually less for a horizontal

base and it is simpler to construct.
(2) Bearing values and base pressures for the two base types are not
directly comparable. However, for equal heights, base pressures of the hori-
zontal base generally are smaller because of its reduced earth load and
slightly wider base.
b. Sloped Base (Figure 7-4).
(1) A sloped base may allow shortening or complete elimination of a key,

thereby reducing excavation difficulties. Also, a shorter key will generate
less moment in the heel adjacent to the key and will generally allow for a
shorter base width to maintain overturning equilibrium.
(2) The deep cover or blanket over the heel of a sloped base lessens the
chance of rupturing the cover as the wall moves under load.
(3) The resultant of applied forces is more nearly normal to a sloped

base, thereby reducing the tendency of the structure to slide along that plane.
(4) A full-size flood wall test performed by the Ohio River Division
(1948-1956) (U. S. Army Engineer Division, Ohio River 1958) indicated that the
sloped-base wall moved consistently less than the horizontal-base wall of
comparable design.
c. Selection. Both base types have their advantages and disadvantages.

Final selection will depend upon the specific site conditions at the project
under consideration.
7-6. Horizontal Water and Earth Loads on Keys. For flood walls on clay
foundations, full flood head will be conservatively assumed to act at the bot-
tom of the key and the horizontal water load acting on the riverside face of
the key will be computed on this basis. The seepage path will then be assumed
to begin at the bottom of the key. The landside face of the key will normally
be assumed to be in full contact with the earth-resisting movement of the wall.
7-7. Unsuitable Foundation Material and Bank Stability. Foundation material

found to be unsuitable may be avoided by a change in alignment or may be re-
moved and replaced with suitable earth fill (Figure 7-5). The wall may also
7-10
EM 1110-2-2502
29 Sep 89
Heel —H r"-Toe—*~
- Base Width
-Sheet Pile
Cutoff (Optional)
Figure 7-4. T-type flood wall--sloped base
be founded on piles through the unsuitable material. In some cases the removal
of unsuitable foundation material involves the removal of or cutting into the
existing riverbank on which the flood wall is to be placed. In other cases the
right-of-way may be so restricted and confining that the flood wall may have to
be placed near the top edge of the bank or even riverward of the bank. In
those cases, fill placed riverward of the top bank is permitted, if proper
precautionary measures are taken. Careful attention must be paid to the
outlining of and removal of unsatisfactory material and to the selection of
suitable replacement material. New material must be obtained, placed, and
compacted to provide adequate support for the flood wall. Replacement material
should undergo the same types of laboratory testing as existing foundation
material. Placement and compaction techniques should generally be in
accordance with earth dam and levee requirements. Slopes steeper than 1.0V on
1.5H and areas that require hand compaction should be minimized. Slopes on
which there is evidence of past instability, or in which fill is a component,
7-11
EM 1110-2-2502
29 Sep 89
u
<0
■U
m
e
c
o
•H
4J
(H
>a
c
o 3
O
l_ IR
<D
-#-* a)
O i-i
S •su
c •H
o 3
CO
■*-> c
a p
u
c o
3
o CO
u. 4-1
•H
<D B
•H
JO r-l
O
->-> rH
cd
73 >
CO g
6
at
1 t*
CM
in
CD 1
C h-
o
tsl 1J
3
60
pH
7-12
EM 1110-2-2502
29 Sep 89
should be investigated for stability. All riverward slopes should be checked

for stability if the failure of the bank would jeopardize the stability of the
wall.
7-8. Scour Protection. Occasionally a flood wall is exposed to scouring

because of the direction, curvature, and velocity of current or waves, charac-
teristics of the soil, topography, etc. Scouring at the wall footing should be
considered, and where anticipated, protected with riprap. Design guidance on
sizing riprap is given in EM 1110-2-1601.
Section IV. Types of Monoliths
7-9. Change-of-Alignment Monoliths. Changes in alignment require special

monoliths (Figure 7-6) . Monoliths with less than a 10-degree change (horizon-
tal) do not need to be analyzed as a special category. Monoliths of short
length or abrupt alignment changes may require very wide bases. A 90-degree
corner monolith is an indeterminate structure. Adjacent monoliths should not
be considered to provide resistance in the stability analysis.
7-10. Closure and Abutment Monoliths. A number of openings must be provided

in many flood walls. The openings provide access for commerce, safety, and
recreation during periods of low river stages. The number and size of openings
depend on local requirements. Each opening must be provided with a moveable
closure structure. During flood periods, the closure structure is installed on
base and abutment monoliths (this combination is a special monolith). These
special monoliths must be designed both for the design water load at high water
and traffic loads during low-water periods.
7-11. Drainage Structure Monoliths. When topography, foundation conditions,

and economics permit, it is preferable that structures housing gates and pumps
be designed as integral parts of the flood wall. These special monoliths must
be designed to minimize differential settlement across a monolith or between
adjacent monoliths. For closure gate requirements and the need for secondary
closure gates for drainage outlets, see EM 1110-2-1410.
7-12. Transition Sections Between Flood Walls and Levees.
a. Junctures. A junction between a T-wall and levee is not made

directly or abruptly, but with a short transition concrete-capped sheet piling
I-wall between the two (Figures 7-7 and 7-8). One of the primary concepts in
the development of this transition is to arrange details so there will be a
minimum amount of differential movement of joints of monoliths in the transi-
tion. The levee end of the transition will usually settle a considerable
amount, due primarily to foundation consolidation under the added weight of
the levee. The T-wall monolith immediately adjacent to the beginning of the
levee adds far less superimposed weight on the foundation. Hence, there is
much less settlement at this end of the transition. The I-wall can be satis-
factorily adopted as a transition section between levee and T-wall because
this type of construction can, and in fact must, be done after completion of
the levee. A delay in inserting the I-wall allows for settling of the levee,
7-13
EM 1110-2-2502
29 Sep 89
Re—entrant
LAND SIDE monolith
PLAN
WATER SIDE
•Joint filler
Reinforcement \N
V N
continuous \
across V
contraction
joint. Keys
-Stem
Joint filler
■Toe
JL
Re—entrant monolith —
LAND SIDE
PLAN
Expansion joint material (paragraph 7—14a) to be
used where each end of re—entrant monolith
touches the adjacent monoliths (see Figure 7—9a).
Figure 7-6. Return keys on reentrant monolith
7-14
EM 1110-2-2502
29 Sep 89
o §
U
•H
in 0)
Ö
< td
u
a: u
0)
ÜJ
Lü 5
>
ÜJ
s
■d
o
o
<D
M
3
00
< •H
Pn
7-15
EM 1110-2-2502
29 Sep 89
trt
c
CO
!-!
cd
&
I
s
4-1
o
"4-t
o
•H
4J
o -i
00 < o
«0
•H
< a
c E-t
+- 00
o 1
to
V)
,,_
■H
fa
■i- i~
ü o>
oil'
© O 0)
-f- «0
zo
7-16
EM 1110-2-2502
29 Sep 89
thus lessening the differential settlement between the levee end of the
transition and the T-wall. Review by hydraulic engineers is required for
inland flood walls to assure that the transition geometry will not create sig-
nificant flow disturbance with consequent scour.
b. I-wall. The I-wall portion of the transition is begun where the levee
slope (parallel to the protection) reaches a point 10 feet below the top of the
wall. In cases where protection is already 10 feet or less above the levee, an
I-wall, if used, is merely continued into the levee as shown in Figure 7-7.
c. Sheet Piling. It should be noted in Figure 7-7 that the sheet piling
is continued into the levee for a specified distance beyond the last concrete
cap.
Section V. Water Stops and Joints
7-13. Water Stops. As shown in Figure 7-9a, b, and c, for yielding founda-
tions a U-shaped (type "U") water stop should enclose almost the entire base
and a center bulb (type "Y") water stop, located in the stem, is joined to the
U-shaped water stop at the bottom of the stem. Experience has shown that a
center bulb or dumbbell water stop located within the base section is likely to
allow excessive seepage. Between monoliths on a foundation requiring a cutoff,
the type Y water stop in the stem should be extended to tie into the cutoff,
and the type U water stop around the base should be deleted. The earth surface
on which a type U water stop is installed must be firm and smooth, with no
chips, sags, humps, clods, or loose debris that would prevent intimate contact
between the water stop and soil. See Chapter 6, paragraph 6-4e, for general
guidance on water stops. Because field construction problems are common for
the type "A" joints shown in Figure 7-9a with the type U water stop shown in
Figure 7-9b, and because the buried base slab does not experience wide
temperature changes, an optional base slab joint is allowed when the base is
placed. This base slab joint uses construction joints without water stops but
with the base slab longitudinal reinforcement continuous through the joint.
When this option is used, longitudinal reinforcement of at least 0.4 percent of
the slab cross-sectional area must be provided in the base slab, half in each
face, but with not more than #9 reinforcing bars at 12-inch spacings in each
face.
7-14. Contraction and Expansion Joints. Contraction and expansion joint

details are illustrated in Figures 7-9a through 7-9c. Contraction joints
(type A) should contain a bond-breaker. Expansion joints (type "B") should
contain 1/2-inch preformed expansion joint filler in:
a. All protruding (convex on water side) monolith bases, and in selected

reentrant monolith bases and stems as shown in Figure 7-6.
b. In bases and stems of alternate monolith joints in straight-line runs,

if warranted by previous experience with similar foundation conditions.
7-17
EM 1110-2-2502
29 Sep 89
See Detail "A'
Type T Circular opening of water-

Waterstop stop at top to be plugged
with soft rubber for a min-
imum depth of 2 Inches. -
River side
of was
Bond breaker as
required. (See Kf1
Section A-A and B-B) ■ 4 Type ■Y"
Waterstop
Ground surface
Transition
(See detail
on Figure T-9c )
Type "Y" Vz' premoulded

waterstop expansion Joint
material.
Make Joint I'
thick at change
of direction
Contraction Joints, stems
bond breaker
MONOLITH JOINT TYPE 'A' MONOLITH JOINT TYPE 'B'

SECTION A-A Yz' premoulded
_J7p
expansion Joint
Contraction Joints,
T^r material.
bond breaker
-Type 'U'
± waterstop "-Sir i.
MONOLITH JOINT TYPE 'A' MONOLITH JOINT TYPE V
SECTIPN p-p
MONOLITH JOINT DETAIL
NOTES:
1. Extreme care should be exercised in placing type 'U* rubber
waterstop to Insure firm contact with the prepared subgrade
throughout Its entire contact areo.
2. Type 'A* Joint used In straight runs of wait, 30 feet spacing
3. Type "B" Joint used In Junctures of won with gate wells,
pump stations and gate abutments, and In change of direction monoliths.
a. Monolith joint detail

Figure 7-9. Typical joint and water stop details (Sheet 1 of 3)
7-18
EM 1110-2-2502
29 Sep 89
River face of wall

Varies r-6 r-6"
Type "ir
Type 'Y'rubber waterstop Detain'
waterstop
High base
Varies
Type "U" rubber
waterstop
ÜL
Detail T—^_^
Varies
SECTION C-C SECTION D-D
r-6* , r-6"
Type "IT r-6" A I'-6"
waterstop Type "U"
^ u waterstop
A—|
5-gage
wire el 2'
Varies for each

height per low
Low base wall base wall
PLAN
TRANSITIONS AT CHANGES IN WALL HEIGHT

b. Transitions at changes in wall height
Figure 7-9. (Sheet 2 of 3)
7-19
EM 1110-2-2502
29 Sep 89
Type "Y"
'/,■ R. (TYP)
The Type 'Y" and Type "U" waterstops

shall be Joined by vulcanizing if
rubber waterstops are used ; or
by heat sealing the joint if
PVC waterstops are used.
Base
-Type 'U"
TRANSITION BETWEEN STEM AND BASE

ISOMETRIC SKETCH
9'//
TYPE "U"
c. Water stop details
Figure 7-9. (Sheet 3 of 3)
7-20
EM 1110-2-2502
29 Sep 89
c. In bases and stems of junctures of walls with gate wells, pump

stations, gate abutments, and similar structures. Nonflexible material in a
protruding angle joint is particularly dangerous.
d. See paragraph 6-4 for general guidance on joints.
Section VI. Site Considerations
7-15. Adjacent Structures and Rights-of-Way. Flood walls are usually built
because only a narrow right-of-way is available. The presence of existing
buildings or other structures is usually the reason for a narrow right-of-way.
Sewer pipes with open joints, structures with basements, and excavations close
to the wall may create a hazard to the safety of a flood wall. Also, new
structures that are built close to existing flood walls can create the same
hazards. Present right-of-way acquisition policies do not permit legal re-
strictions to be placed on future construction; however, local interests
should be advised in writing of potential hazards, of required design and con-
struction measures, and should be requested to closely supervise new con-
struction close to the flood wall. Potential hazards can be avoided by proper
design and construction measures. One hazard that should be considered is
seepage. A basement or other excavation on the landside of the flood wall may
result in shortened seepage paths. A basement or excavation on the riverside
may also create a safety hazard if it penetrates the impervious blanket or
shortens the seepage path. When feasible, the basement or excavation should
be backfilled with the same type of material existing in the foundation of the
flood wall. If relief wells are selected to control seepage they should be
located, if at all possible, between the flood wall toe and the adjacent
structure. Protection of the basement area may require lowering of discharge
elevations for safeguarding the wall. The location of relief wells within a
basement area is not prohibited, but it leads to problems of construction,
maintenance, and discharge collection. If the seepage problem is only one of
quantity, sump pumping may be used during periods of high water. A second
hazard that landside basements and excavations create is to lessen the resis-
tance to sliding along a foundation failure plane. For this reason potential
planes of sliding into basements or excavations should be studied. If back-
filling is not possible, other measures include the addition of fill between
the stem and the building or strengthening the basement to provide the needed
resistance. Riverside excavations which contribute to riverward foundation
instability should be backfilled, at least to the extent that stability
requirements will be satisfied. For the special situation where a wall in a
congested location is subjected to an unusually large horizontal force, such
as the force of a breaking wave, T-type flood walls are frequently worth the
extra cost over other types of construction. This situation requires an
unusually wide base for sliding stability, requiring more right-of-way and,
hence, more cost for construction. The relatively thin stem of the T-wall
does, however, provide the most usable surface area adjacent to the stem after
backfilling, in comparison with embankment, braced walls, etc., making the
T-wall the preferred solution in spite of the extra construction easement
right-of-way. While an I-wall also provides little intrusion on the completed
7-21
EM 1110-2-2502
29 Sep 89
surface area, its use can be precluded by the pile-driving vibration and con-
sequent chance of damage to adjacent structures.
7-16. Architectural and Landscaping Considerations. Aesthetics should be con-

sidered in the design of flood walls, from the standpoint of blending the
project with the surroundings. Whenever possible, the wall should appear to be
a natural extension of the local topography. The basic design of these
structures should be a coordinated effort between the design engineer, the
architect, and the landscape architect. While it is seldom feasible to pre-
serve the natural setting intact, design techniques and careful construction
methods can be used to protect or even enhance the aesthetic value of the
immediate project area. Landscape planting design for project structures
should consider the entire area affected by the contemplated construction.
Further details may be found in EM 1110-1-2009 and EM 1110-2-301.
Section VII. Instrumentation
7-17. General and Specific Considerations. Flood wall instrumentation should

be considered so that performance can be monitored, particularly during periods
of high water. The decision on how much, if any, instrumentation is
appropriate must be based on these factors:
a. Who will monitor and evaluate the instruments--Corps of Engineers,

local interests, etc., and how meaningful their evaluations are expected to be.
b. Access to the instruments during flood conditions, especially during

hurricane-flood situations where high winds may make accessibility impossible.
c. Time required for meaningful evaluation, compared with the expected

duration of the flooding.
d. Other particular considerations for specific situations.
The instrumentation descriptions that follow must be implemented in light of

the above decision. Specifically, areas with high walls, low embedment
ratios, replaced foundation materials, overbank fills, pervious materials in
the foundation, and changes in direction should be considered for instrumen-
tation. When founding a flood wall on earth, the distance between monoliths
with piezometers should not exceed 1,000 feet unless warranted by site
conditions. Properly installed, maintained, and observed instrumentation can
forewarn of dangerous conditions that may affect the stability of the struc-
ture. All instruments should be read soon after construction is complete.
Knowing the as-built conditions of the wall is essential for an accurate
determination of later behavior. Initial piezometer readings should be
repeated until equalization (steady state) occurs. All instrumentation read-
ings should be made by trained survey or flood-patrol personnel. Ideally, all
instruments will be read frequently during high water stages. During design
floods, the procedure may prove almost impossible because of the need for
trained personnel to direct flood fights; but readings should be made at
7-22
EM 1110-2-2502
29 Sep 89
certain, previously selected, critical locations during design flood stages.

During normal water stages, instruments should be read prior to district
periodic inspections so that the inspection party has the necessary evaluation
data. Such data also provide a history of flood wall reactions over the years,
during both high and normal water. Information concerning frequency and manner
of conducting periodic inspections and evaluations is contained in
ER 1110-2-100, while ER 1130-2-339 covers local flood protection projects.
7-18. Types of Instrumentation. The principal types of flood wall instrumen-

tation monitor movements, both vertical and horizontal, and hydrostatic pres-
sures in the foundation. The instruments selected should be simple to install
and observe, and efficient in performance and functional reliability. The
monitoring of the movements provides an indication of possible sliding in-
stability or possible water stop rupture. The piezometers provide a record of
hydrostatic pressures in the foundation which can indicate uplift and possible
excessive seepage pressures. Instrumentation systems, installations, and
devices are discussed in detail in EM 1110-2-4300.
a. Movement Monitoring. All reference points to monitor movements should

be tied in to a permanent baseline located so that it is unaffected by
movements of the wall. When establishment of a baseline is not feasible, the
relative movements observed between monoliths or by means of triangulation can
provide valuable data on behavior of the wall. Reference points to monitor the
wall movements need to be installed during construction. Noncorrosive metal
plugs should be installed in the top surfaces of the stems within 6 inches of
each end of each monolith. The reference marks in the plugs of four to six
successive monoliths should be placed in a straight line with theodolite or
stretched wire. At changes in alignment, the straight line should be continued
until it intersects the far side of the next monolith and a reference point for
alignment control is placed. Each plug's changes in horizontal movement and
elevation should be measured to 0.001 foot. Stations to be read with
electronic optical reading devices need to be established at locations near the
ground surface level on the landside of the stem. Selection of
electronic-optical station locations for the stem should be based on factors
such as changes of direction, areas of overbank fill, foundation replacement,
high walls, low embedment ratios, and junctures of flood walls with drainage
structures. The monitoring system selected should be vandalproof. In many
cases the monitoring system can be tied into the same baselines established for
the reference markers on top of the wall. Tilting of stems can be measured by
a tiltmeter.
b. Foundation Piezometers. Design, installation, and observations of

piezometers are described in EM 1110-2-1908, Part I. The simplest, most
reliable method of measuring pore water pressures is the open tube piezometer.
For impervious soils, the Casagrande type of piezometer with 24-inch-long
porous stone is recommended. In order to measure the piezometric pressure at
the porous tip, the boring for installation of the Casagrande piezometer must
be effectively sealed against migration of seepage along the piezometer riser.
For semipervious to pervious soils, a driven wellpoint type of piezometer is
recommended. Where possible, the wellpoint should be driven into undersized,
7-23
EM 1110-2-2502
29 Sep 89
pre-bored holes. More piezometers can be added if foundation conditions

warrant.
Section VIII. Operation and Maintenance Manual Requirements
7-19. General Coverage. General coverage of the requirements of local coop-

eration is contained in EM 1120-2-109. As written, the regulations are general
in nature and obviously cannot give detailed instructions for the maintenance
and operation of a specific project. Therefore, it is necessary for the
district office having jurisdiction over the specific project to issue an
adequate operation and maintenance manual for the guidance of local interests.
Section IX. Review of Existing Flood Walls
7-20. Inspection. Flood walls should be examined during scheduled periodic

inspections, after major periods of high water, and when special events warrant
an inspection (building or excavating near the wall, etc.). A determination of
areas which may be weak or critical from the standpoint of leakage and
stability should be made. Criteria for this determination are described below.
Areas deficient in any of the criteria will be considered weak or critical,
depending on the degree of deficiency.
a. Horizontal Movement. Areas in which movement of a straight section of

monoliths or differential movement between any two monoliths is greater than
expected will be considered critical.
b. Joint Opening or Spreading. Joints referred to in this paragraph are

those having a water stop embedded in the interior of the section. Using the
results of the full-size flood wall test performed by the Ohio River Division,
(ORD) in 1955, expected spreading of joints at 90-degree reentrant corner
monoliths (concave on the riverside) will be 42 percent of the expected move-
ment of the straight run walls. Not only may joints at corner monoliths become
critical upon application of load, but open joints below ground should be
considered critical. Any joint can become open through loss of joint filler or
through unequal settlement between adjacent monoliths or structures such as
levees, pump houses, gate wells, and gate abutments. Some joints below ground
may need to be excavated to determine the adequacy of joint filler. If the
expected joint opening is greater than the allowable, the area should be con-
sidered critical.
c. Foreign Material in Joints. The presence of inflexible foreign mate-

rial, such as grout and pieces of aggregate, in expansion joints is dangerous
from two standpoints. Grout, particularly if located within the fold of the
water stop, destroys the flexibility of the water stop and, upon the occurrence
of differential movements, allows the water stop to be torn. Grout and pieces
of aggregate anywhere in the joint prevent the joint from fulfilling its
expansion function. This condition becomes particularly dangerous at
protruding angle locations; i.e., where the wall appears convex when viewed
from the river. Here, the wall may be tilted waterward by a wedging action
upon expansion of adjacent monoliths in hot weather. This wedging of adjacent
7-24
EM 1110-2-2502
29 Sep 89
monoliths at changes in alignment is likely to force excessive flexure in the

stem, sufficient to cause failure. The same tilting can occur at reentrant
monoliths (Figure 7-6), but there the tilting is landward and the reinforcing
is more adequate to resist the stress. For angle monoliths protruding toward
the river, the landside temperature steel can be quickly overstressed.
d. Water Stops. Joints with torn or parted water stops should be con-
sidered critical. Torn water stops may not be noticed during an inspection,
particularly if the joint has not spread open. If sufficient differential
movement has occurred, it should be assumed that the water stop is torn. The
amount of tearing to be allowed should be based on factors causing piping;
however, this is very difficult to predict. In the above cases, if a total
differential movement (transverse and longitudinal combined) of 1/2 inch or
more has occurred, the water stop should be considered torn unless shown
otherwise.
e. Foundation Voids. All unequal settlements should be viewed with

suspicion. In particular, unequal settlements adjacent to structures such as
pump houses and gate wells should be the subject of rigid examination. Usually
one or two monoliths (or a portion of one monolith) are constructed on
compacted fill in these areas. Initial unequal settlement may cause the first
monolith to bridge or wedge between the second monolith and the other struc-
ture. Further consolidation of the fill then leaves a dangerous void or voids
under this base. Only underground examination will reveal the presence of
these voids.
f. Stability Analyses. Original seepage assumptions or patterns should

be reviewed for realistic representation of actual foundation conditions.
Particular attention should be paid to foundations having pervious strata which
connect directly with the river. Where indicated, seepage and/or stability
analyses should be recomputed as described in Chapters 3, 4, and 5. In
addition to a recomputation of uplift, the shear strengths used in the original
analyses should be reevaluated on the basis of a study of types of soil and
their drainage and consolidation characteristics. In cases where there is a
lack of sufficient foundation information in areas suspected to be weak, new
soil samples should be obtained as close to the existing wall as is feasible.
Areas found to have questionable stability should be closely observed during
high floods.
g. Basements and Other Excavations. The seepage aspects and the founda-
tion stability of walls which have had basements excavated on either side of
and adjacent to the wall since the original design and construction were
completed should be investigated.
h. Seepage Conditions Landside of Flood Walls. These areas should be

investigated thoroughly and seepage control of pressure relief provided, if
needed.
7-25
EM 1110-2-2502
29 Sep 89
7-21. Repair Measures.
a. General. The following repair measures are only suggestions. Their

use is not mandatory if more feasible or economical measures can be devised for
the individual problems involved.
b. Additional Landside Cover. The most obvious and straightforward

method for reducing anticipated horizontal movement or increasing sliding
stability is the addition of landside cover or fill to the wall (see Fig-
ure 7-10) . At locations where additional landside fill is not feasible or
possible due to highways, railroads, and other structures, measures to reduce
seepage pressure (such as those described below in paragraph 7-21d) will have
to be employed to decrease landward movement or increase sliding stability.
c. Additional Waterside Cover. In areas where earth cover over the

waterward end of the heel is deficient, the recommended remedy is the addition
of cover.
d. Supplemental Water Stops. The supplemental water stop scheme shown in

Figure 7-11, a and b is a means of correcting for torn water stops, open
joints, and possible earth cracking over the key because of thin heel cover or
excessive movements. The sheet piling shown in the scheme is necessary to
provide additional cutoff to compensate for loss of part or all of the normal
seep path between earth and the waterside face of the key. The pile cap should
be placed at the bottom of the key to limit excessive leakage of water around
the upstream and downstream ends of the pile curtain as the wall moves landward
under load. Another possible method of repair is to seal the opening below the
existing water stop in the base by injecting cement grout. The opening above
the water stop in the base could be sealed with an elastic sealant such as
polysulphide elastomer.
e. Other Problem Areas. Foreign incompressible material in the joints

should be removed by the most expedient method. Riverside excavations near the
heel should be backfilled with impervious material if it is suspected that
dangerous seepage conditions may occur during high water.
f. Overtopping Scour Control. For coastal walls or other walls where

scour has removed landside cover, consideration should be given to placing
concrete slabs over the restored cover within a distance of 20 feet from the
wall stem.
7-26
EM 1110-2-2502
29 Sep 89
_SZ_
m
Variable
Sand or sand and gravel;

or other heavy pervious
material.
A*
Waterstop O
Path of Possible Leakage

in Spread Joints.
Note: The area and depth of material shall

be sufficient to prevent loss of
foundation material as determined
by observation of the outflow.
Figure 7-10. Emergency measures to control piping
7-27
EM 1110-2-2502
29 Sep 89
Concre+e
blisters
%■ dowels
e 12'-
/ watersfl-op
Vlarlable
NOTE:
For Section D-D. see FIGURE 7-1 IS.
\ /—River
i— Kiver face
Tace
/ existing wall.
z >
— top of base slab
or face of key
Sheet -
piling •4el6" thru sheet
pile lift hole or Existing waterstop—'L=
hole burned In & expansion Joint ^ Detail'2'
field
SECTIONS A-A & B-B SECTION C-C
Figure 7-11. Permanent water stop repair measures (Continued)
7-28
EM 1110-2-2502
29 Sep 89
All circular openings Fill with

at waterstop extremities bituminous
T are to be plugged with cement
River face of wall soft rubber for a
minimum depth of 2 tn..- Top of
Type "Y* rubber- existing
waterstop wall
9:
Sand blast or bush dowels
hammer existing surface-
Type 'Y-
waterstop
River face of
existing wall Sand blast
or bush hammer
existing surface
SECTION AT TOP OF WALL
r-0'or as]
required J Type "U" »4el2 Waterstop
waterstop
Sheet « See Detail'A'
Piling —H| -Top of
base slab
TYPICAL SECTION AT JOINTS Top of
base slab 1
■ Existing
wall base
l*-6
I "4
Existing —i Existing
Fill with wall bôse ;\ j .*' expansion
bituminous Joint
cement 9"
'/z* expanston
River face Joint
of existing Top of SECTION D-D
wall — sheet Type "Y" Web of
pile waterstop• Type 'Y"
r2" mln.
plug with
soft rubber
or rubber
Existing Top of wall —L cement
expansion Joint warles
PLAN AT TOP OF WALL
%,x2l/2,x6'
Notes for DETAIL 'A' Cont. weld rubber
1. %x2/2" rubber strips are for use %,x2'/2"x8l/2' Type "U"
only at change In dlrrectlon where rubber— 1 waterstop
type "U' stop must be cut on a bias DETAIL, "A
and re-joined. On straight runs these
strips need not be used. NOTES:
2. Bulbs of type 'Y' stop are shaved down 1. For details of "Y" & 'U- type
rubber waterstop, see FIGURE 7-9C
to web to provide a flat surface for 2. All steel In blisters 2' clear.
bolting to Inside of type 'U' stop. 3. For Section C-C, see FIGURE 7-IIA
3. All rubber surfaces In contact with each 4. For Section D-D location,
other are coated with rubber cement. see FIGURE 7-1IA
b.
Figure 7-11. (Concluded)
7-29
EM 1110-2-2502
29 Sep 89
CHAPTER 8
CONCRETE GRAVITY WALLS
8-1. General Factors. Factors favoring concrete gravity retaining walls are
shallow depth of overburden, a competent foundation, and an adequate source of
fine and coarse aggregate for the required volume of concrete. See Chapter 2,
Section I for additional comments on gravity walls.
8-2. Foundation Investigation. The requirements for the foundation investi-

gation are discussed in Chapter 2, Section V.
8-3. Materials. A concrete compressive strength of 2,000 to 2,500 psi will

usually meet the requirements for the gravity type wall. Where the environment
requires durability, such at as the outer surface of the wall, the higher
strength should be achieved with the appropriate water-cement ratio from
EM 1110-2-2000.
8-4. Design.
a. Magnitude and Distribution of Forces.
(1) Dead Load. The unit weight of concrete is usually assumed to be

150 lb/cu ft. This value may vary, depending on the aggregate. Other dead
loads that should be considered are superimposed backfill and the weights of
any equipment or other structures supported by the wall.
(2) External Water Pressure. The pressure exerted by water above ground
and water in the ground should be determined as described in Section III of
Chapter 3.
(3) Internal Water Pressure (uplift). The uplift on a lift (horizontal

construction joint) within the body of a concrete gravity wall for long-term
water levels should be taken as 50 percent of the value obtained by assuming a
straight line variation between the full hydrostatic pressures acting on each
side of the wall. Uplift pressures on the base of the wall should be deter-
mined by the methods described in Section III of Chapter 3.
(4) Lateral Earth Pressures. Lateral earth pressures should be deter-

mined by the methods presented in Section II of Chapter 3. Computation
examples, as applied to gravity walls, are shown in examples 5, 6, 8, 10, and
11 of Appendix M.
(5) Wind and Earthquake Forces. These supplemental forces should be

determined by the methods presented in Section IV of Chapter 3.
b. Load Cases. The load cases should be those described in Section I of

Chapter 4.
8-1
EM 1110-2-2502
29 Sep 89
c. External Stability. Sliding and overturning stability should be

determined by the methods and criteria discussed in Chapter 4. Computer
program 3DSAD will significantly assist in performing stability analyses. An
example of a complete stability analysis of a gravity wall section is shown in
example 2 of Appendix N.
d. Internal Stability. The resultant of all forces acting on any hori-

zontal section should fall within the kern or sufficiently close to the kern of
the section to keep the tensile stresses low. See EM 1110-1-2101 for allowable
concrete stresses.
e. Foundation Analyses. Foundation analyses should be performed in

accordance with the methods described in Chapters 4 and 5.
8-2
EM 1110-2-2502
29 Sep 89
CHAPTER 9
CANTILEVER REINFORCED CONCRETE WALLS
9-1. General Characteristics. The cantilever reinforced concrete wall is a

special type of gravity wall in which part of the stabilizing weight is sup-
plied by the weight of the backfill resting on the base slab. The structural
members are designed for stresses due to bending and shear. Chapter 2, Sec-
tion I, offers additional general comments on cantilever concrete walls.
9-2. Foundation Investigation. The requirements for the foundation investi-

gation are discussed in Chapter 2, Section V.
9-3. Materials. Concrete materials and mixture proportioning, with appropri-

ate water-cement ratios for durability, should follow guide specification
CW 03301 and EM 1110-2-2000. Typically, a concrete compressive strength of
3,000 psi is used for retaining walls. The age at which the specified strength
is to be obtained should be decided by the designer depending on the loading
conditions anticipated. Steel reinforcement bars should follow the
specifications in the American Concrete Institute (ACI) Building Code
(ACI 318), with the exception that for hydraulic structures the grade of steel
will be limited to ASTM Grade 60 without special approval.
9-4. Reinforcement Cover. For hydraulic structures the minimum reinforcement

cover should comply with EM 1110-2-2103. For structures not subject to
hydraulic action the minimum reinforcement cover should comply with the ACI
Building Code requirements.
9-5. Load Cases. The load cases should be those described in Section I of
Chapter 4. The magnitude and distribution of the loads should be determined as
described in Chapter 3.
9-6. Structural Stability. Sliding and overturning stability should be

determined by the methods and criteria discussed in Chapter 4. Forces and
moments for structural design should be based on external forces allocated
according to paragraphs 3-7 through 3-9 and calculated as described in
Section III of Chapter 4 for overturning stability. Sample stability
calculations are shown in Appendix N.
9-7. Structural Design.
a. General. Reinforced concrete walls should be designed for the loading

cases given in Section I of Chapter 4 and the foundation pressures obtained
from the overturning stability analysis described in Section III of Chapter 4.
Wall components should be analyzed as cantilever beams. Compression rein-
forcement is not normally used. Temperature and shrinkage reinforcement should
conform with EM 1110-2-2103. Example calculations are shown in Appendix N.
When the top surface of backfill is sloping upward, a shear force in addition
to the horizontal earth force should be considered acting on the structural
wedge (see Figure 9-1).
9-1
EM 1110-2-2502
29 Sep 89
Line of action of
resultant force
Shear = P (h, - h? )
<M
r.
f,'\ ^\m\ L:
Shear Force when h, > h2
Figure 9-1. Shear force for upward-sloping backfill
b. Stem. Axial loads are usually small and may be neglected in design.
c. Toe. The toe should be designed with loads imposed by soil, water,
concrete, bearing pressures, etc. The effects of axial loads are not ordi-
narily substantial enough to be taken into account.
d. Heel. The loads for calculating design moments are the weight of
soil, water, and concrete acting downward, along with uplift and bearing pres-
sure acting upward. The bearing pressure should be determined using the hori-
zontal earth force and shear when the backfill surface is sloping upward (see
paragraphs 9-7a and 4-8c). With no key, the base shear should be neglected
when computing reinforcement, as illustrated in Appendix N, example 1.
e. Special Considerations for Walls with Keys. The overturning stability

criteria for walls with keys include an assumed uniform distribution of earth
pressure on the resisting side of the key that may result in unconservative
design for reinforcement in the top face of the wall heel at and near the face
of the stem. A portion of this force may actually act along the plane at the
base slab of the wall and not on the key. The designer is cautioned to
consider this in developing a reinforcing design. A conservative approach for
design of the heel top steel at the stem would result from the use of founda-
tion pressures obtained from a stability analysis assuming that all of the
earth resistance acts along the plane at the base of the wall. See Section III
of Chapter 4, especially paragraph 4-8b. Stability calculations for walls with
keys are shown in examples 3 and 6 of Appendix N.
9-2
EM 1110-2-2502
29 Sep 89
9-8. Reinforced Concrete Design.
a. General. Reinforced concrete walls should be designed with the

strength design method in accordance with the current ACI Building Code, except
as herein specified. Notations used are the same as those in the ACI Code,
except those defined herein. (Appendix D lists the Notation used in Chap-
ter 9.) WES Technical Report SL-80-4 (Liu and Gleason 1981) contains design
aids consistent with the information presented in paragraph 9-8b of this
chapter. Retaining walls and flood walls may be designed using the same load
factor for concrete weight as that selected for earth and water loads, as
explained in paragraph 9-8b(l), Equations 9-5 and 9-6.
b. Hydraulic Structures--Strength and Serviceability.
(1) Required Strength. Reinforced concrete hydraulic structures should

be designed to have strengths in all sections equal at least to those calcu-
lated for the factored loads and forces in the following combinations that are
applicable.
(a) For usual loading cases Rl, II, Cl, C2a, and C2c as described in
Chapter 4:
U - 1.5D + 1.9L (If D and L have the same sign) [9-1]

or
Ü - 0.9D + 1.9L (if D opposes L) [9_2]

where
D = internal forces and moments from dead load of the concrete members
only
L = internal forces and moments from live loads (loads other than the
dead load of concrete members)
(b) For unusual or extreme loading conditions such as cases R2, R3, 12,
13, 14, C2b, C3, C4, and C5, earthquakes, and short-term loadings:
Ü - 0.75(1.5D + 1.9L) (if D and L have the same sign) [9-3]
or
U = 0.75(0.9D + 1.9L) (if D opposes L) [9-4]
9-3
EM 1110-2-2502
29 Sep 89
(c) In most retaining walls and flood walls, dead loads represent a small
percentage of total loads and the additional effort to recompute another
stability analysis using the above two factors may not be warranted. There-
fore, a single load factor as defined by Equation 9-5 may be substituted for
Equations 9-1 and 9-2 to avoid having to recompute an alternate stability
analysis with a different set of loadings. Likewise, Equation 9-6 may be sub-
stituted for Equations 9-3 and 9-4.
Ü - 1.9(D + L) [9-5]
Ü = 0.75[1.9(D + L)] [9-6]
Note that the AC1 definition of D is modified so that
D = dead load of the concrete members only or related axial forces,

shears, and moments
L = all loads other than dead load of concrete, or related axial forces,
shears, and moments
(d) When multiple load factors are used and the reactions (i.e., base
reactions, pile reactions, resisting earth pressures, etc.) are computed using
the applied factored loads, the following combinations should be considered:
From Equation 9-1: D = 1.5D + 1.9L + R [9-7]
From Equation 9-2: U = 0.9D + 1.9L + R [9-8]
From Equation 9-3: U = 0.75(1.5D + 1.9L + R ) [9-9]
From Equation 9-4: U = 0.75(0.9D + 1.9L + Rf) [9-10]
where R equals internal forces and moments resulting from reactions induced
by the applied factored dead and live loads.
(e) When the single load factor is used and the reactions (i.e., base
reactions, pile reactions, resisting earth pressures, etc.) are computed using
the applied unfactored loads, the following combinations should be considered:
(See paragraphs j and k, Example 1, Appendix N).
From Equation 9-5: U = 1.9(D + L + R) [9-11]
9-4
EM 1110-2-2502
29 Sep 89
From Equation 9-6: U = 0 .75 [1.9 (D = L + R) ] [9-12]
where R equals internal forces and moments resulting from reactions induced
by applied unfactored dead and live loads.
(2) Design Strength of Reinforcement. The design should be based on

yield strengths of reinforcement of 40,000 psi and 48,000 psi for ASTM
Grades 40 and 60 steels, respectively, except for calculating development
lengths. The development length for Grades 40 and 60 steels should be based on
yield strengths of 40,000 psi and 60,000 psi, respectively. Reinforcement with
a yield strength in excess of Grade 60 should not be used unless a detailed
investigation of ductility and serviceability requirements is conducted in
consultation with and approved by Headquarters, US Army Corps of Engineers
(HQUSACE) (CECW-ED).
(3) Maximum Tension Reinforcement. For flexural members and for members
subject to combined flexure and compressive axial load when the design load
strength ()>P is less than the smaller of O.lOf A or 0P , the ratio of
tension reinforcement provided generally should not exceed 0.25 p. . Rein-
forcement ratios greater than 0.25 p but less than 0.50 p, may be used in
retaining walls if excessive deflections are not predicted when using the
method specified in the ACI Building Code. Reinforcement ratios in excess of
0.50 p should not be used unless a detailed investigation of serviceability
requirements, including computation of deflections, is conducted in consulta-
tion with and approved by HQUSACE (CECW-ED).
(4) Minimum Reinforcement of Flexural Members. At any section of a

flexural member where reinforcement is required by analysis, the minimum rein-
forcement requirements specified in the ACI Building Code, should apply, except
that f should be in accordance with paragraph 9-8b(2).
(5) Control of Deflections and Cracking. Cracking and deflections due to

service loads need not be investigated if the limits on design strength
specified in paragraph 9-8b(2) and a reinforcement ratio of 0.25 p, are not
exceeded. Where these limitations are exceeded, extensive investigation of
deformation and cracking due to service loads should be made in consultation
with higher authority.
(6) Distribution of Flexural Reinforcement. The spacing of flexural

tension reinforcement should not generally exceed 18 inches for Grade 40 steel,
or 12 inches for Grade 60 steel.
(7) Extreme Loadings. For extreme loadings which are highly improbable,
such as from earthquakes which have a frequency of occurrence that greatly
exceeds the economic life of the structure, selection of less conservative
load factors than given in Equations 9-3, 9-4, and 9-6 and less conservative
9-5
EM 1110-2-2502
29 Sep 89
strength criteria than given above may be justified. For extreme loadings,
requests and the justification for varying from the guidance should be sub-
mitted to HQUSACE (CECW-E) for approval.
c. Hydraulic Structures--Reinforced Concrete Design.
(1) Design Assumptions.
(a) Strain. The assumed maximum usable strain at the extreme concrete
compression fiber should be equal to 0.003. The design strain e at the
extreme concrete compression fiber should be limited to 0.5 of the maximum
usable strain for hydraulic structures.
(b) Balanced Conditions. Balanced conditions exist at a cross section

when the tension reinforcement reaches the strain corresponding to its speci-
fied yield strength f just as the concrete in compression reaches its
design strain e . T-wall members should be designed for a ductile failure
on the tensile side of balance, as described in paragraphs 9-7a, 9-8b(3),
and 9-8b(4).
(c) Concrete Stress. A concrete stress of

0.85f should be assumed
c
uniformly distributed over an equivalent compression zone bounded by the edges
of the section and a straight line lying parallel to the neutral axis at a
distance a = ß c from the extreme compression fiber. The factor ß should
be taken as 0.55 for values of f up to 4,000 psi. For values of f
greater than 4,000 psi, ß should be 0.50.
(2) Design Equations. Equations for design and investigation of rein-

forced concrete sections are given in Figures 9-2 through 9-5. These will be
the only equations required to determine flexural adequacy for sections of
retaining and flood walls in practically all cases.
(a) The minimum effective depth (d) needed to provide the amount of
ductility required by criteria may be determined from the following equation
V*
u
<*min
irt = —, iTT [9-13]
0.85f*k
c ■A - r)
1
where
_ f yrPmax _ »
P
m " 0.85f ' max ~ *Pb
9-6
EM 1110-2-2502
29 Sep 89
kjd~ *'(0.85fc' kubd)
i_ *fyAs
DESIGN
GIVEN :Mu,b, d, h, fy,^ ,*=0.9
FIND: ku, As AND p
M 0.85f'c k,,bd
fN
U
Ku = \/l- M As=-
V 0.425 4> V bd'
p = J*S- < pMAX 0.85f=0.9,AS, P = -^_ < PMAX
FIND:ku AND ML
ku- fyP Mu= ^fyPd-T^rJbd

0.85t:
Figure 9-2. Rectangular beam, simple bending with no compression

reinforcement
9-7
EM 1110-2-2502
29 Sep 89
*fyAs
LOADING EQUIVALENT LOADING
FOR EQUIVALENT LGADING: Mue =MU + Pu <d-^)

DESIGN
GIVEN :PU,MU, b, d, h, fy,^, .
W> SHALL NOT BE LESS THAN 0.7) <*>=0.9 -(7rrÄb:)(0.2)
FIND: ku, As AND p *
ku= l-\/l-- Mue 0.85f(ikubd - §-

A« =
V 0.425 <*> f,cbd
Pu
0.85fc ku - *bd
<_ PMAX
INVESTIGATION
GIVEN : Pu,b,d,h,f f^*(SEE DESIGN),ASf P < P,
FIND:ku,Mue AND Mu
+
ku= <^bd fyP , ê = C0.85fiku (|-Â) bdz]<*>
0.85fi
K=MUc -puW -4)
Figure 9-3. Rectangular member, bending with small axial compression
load, no compression reinforcement
9-8
EM 1110-2-2502
29 Sep 89
T
kud ♦ (0.85-^ kubd) *(0.85fikobd)
"■— ft» -
T
\e- (l-iSü)d
h d
Th"
d- KJ P 2
J 5 M ue
-Su.
*fy As
FOR EQUIVALENT LOADING: Mue =MU- Pu (d- 2
DESIGN
GIVEN :PUf MUib, d, h, fy.f^.^sO.9
FIND:ku, As, AND P
ku= |-\/|- M
"*
0.85fckubd + %-
V 0.425 * fc'bd2
Pu
0.85f^ku + 4>bd
f - ^MAX
'y
INVESTIGATION
GIVEN : Pu Pb, d, h, fy , f,Jp*,As,Pbd_ , Mue = [0.85fiku (|-Â) bd2]<*>

0.85f<l
Mu = MUe + PJ (d-§-)
Figure 9-4. Rectangular member, bending with axial tensile load, where
MjP. > (d - h/2)
9-9
EM 1110-2-2502
29 Sep 89
1 *fyAs «ftfy As
Ak
* *
d-*&
i-2^<f>fy As
~*>*
} JL
M<ue
*fy As
FOR EQUIVALENT LOADING: Mu<s = -Mu + Pu (d~y)
DESIGN
GIVEN :PU, Mu, b, d, h, fy,f<;,*=0.9
FIND: As AND A's

Ol X A«
_ -§-! ~ TyAS Ai - Mue
As = 8
" <*»fy (d-d1)
INVESTIGATION
GIVEN : Pu ,b, d, h, fy , f«; , * =0.9, As AND A's
FIND: Mue , Mu AND fs' (STRESS IN A's )
Mue= <pu -+fy As )(d-d')
p ~
% . "£~- fyAs /NOT NECESSARILY EQUAL TO fy\
A*s \^fs <fy IS CRITERIA.
Figure 9-5. Rectangular member, bending with axial tensile load,
where M /P < (d - h/2)
u u
9-10
EM 1110-2-2502
29 Sep 89
and A, is 0.25 for hydraulic structures, compared to a value of 0.75 allowed

by the ACI Building Code. Equation 9-13 is valid only for flexure.
(b) Design aids that will provide essentially the same results as the
equations given in Figures 9-2 through 9-5 may be found in ACI publication
SP-17. These will be valid for hydraulic structures so long as X does not
exceed 0.25 and the allowable capacity of the cross section is limited by
flexural tension. Computer program CSTR (X0066) can assist in the design or
investigation of strength of members in hydraulic structures (Appendix O).
d. Structures Not Subject to Hydraulic Action--Strength and Service-

ability. The strength and serviceability requirements for structures not sub-
ject to hydraulic action should be in accordance with the current ACI Building
Code. Computer program CASTR (X0067) can assist in the design or investigation
of strength of members in walls not subject to hydraulic action (Appendix 0).
e. Structures Not Subject to Hydraulic Action--Reinforced Concrete

Design. Limits on strain, reinforcement, and concrete stress should be in
accordance with the current ACI Building Code.
f. Shear Strength. The shear strength V provided by concrete should

be computed in accordance with the ACI Building Code requirements. For canti-
lever retaining walls the maximum factored shear force should be computed at a
distance d from the base of the stem for stem design, at a distance d from
the stem for toe design, at the face of the stem for heel design, and at the
top of the key for key design. Wherever an L-shaped wall without a toe is
used, the shear force should be computed at the base of the stem for stem
design and at the face of the stem for heel design.
9-9. Foundation Analyses. Foundation analysis should be performed in accor-

dance with the methods described in Chapters 4 and 5 and illustrated in Appen-
dix N. Concrete design should be for earth pressures corresponding to loading
conditions which produce maximum tension in the respective elements of the
foundation slab based on factored ultimate loads. The loading conditions cor-
responding to SMF =2/3 should be considered as a minimum for single wedge
analysis. This does not preclude the use of any other rational method of
analysis that will produce an equivalent design.
9-11
EM 1110-2-2502
29 Sep 89
CHAPTER 10
ALTERNATE TYPES OF RETAINING WALLS
10-1. Classes of Retaining Walls. The four basic classes of retaining walls
are gravity, cantilever, anchored, and mechanically stabilized backfill.
Gravity walls rely on the weight of the wall system to resist overturning. The
cantilever wall is fully reinforced to resist applied moments and shears.
Anchored walls resist lateral forces primarily by the use of tieback anchors.
Mechanically stabilized backfill involves the inclusion of reinforcement in the
soil to form a coherent mass (Godfrey 1984, Mitchell, Villet, and DiMillio
1984, and Jones 1985).
10-2. Alternate Types of Retaining Walls. As discussed previously in Chap-

ter 2, the most common types of retaining walls are gravity and cantilever
walls constructed of cast-in-place concrete. Recently, however, a number of
wall systems utilizing mechanically stabilized backfill as well as new types of
gravity walls have been developed (Godfrey 1984). This chapter briefly
describes mechanically stabilized backfill systems and precast concrete modular
systems. The mention of any specific wall system does not constitute an
endorsement or approval. Numerous wall systems are available and should be
considered when appropriate. This manual does not attempt to provide complete
design and/or construction procedures for the types of walls described in this
chapter. Normally, design and construction procedures are provided by the
manufacturer. However, the manufacturer normally provides only part of the
design. The design engineer must assure the overall adequacy of the design.
Section II. Mechanically Stabilized Backfill Systems
10-3. General Background. Reinforced soil is a construction material composed

primarily of soil with a performance that has been improved by the introduction
of small quantities of other materials. These materials are in the form of
strips, grids, sheets, rods, or fibers which strengthen the soil to resist
tensile forces that soil alone is unable to withstand (Al-Hussani and Perry
1976 and Collin 1986).
10-4. Available Systems. Several mechanically stabilized backfill systems are

available for retaining walls (Mitchell and Villet 1986).
a. Basic Components. Mechanically stabilized backfill systems have

three major components: reinforcements, soil backfill, and facing elements.
Both metallic and nonmetallic (geotextile, plastic) materials have been used
for reinforcement. Granular material is normally used for soil backfill to
meet stress transfer, durability, and drainage requirements. Facing elements
are used to retain backfill material at the face of the wall, to prevent ero-
sion of steep faces, and for aesthetic reasons. The facings are designed to
resist only small horizontal earth pressures. Facing materials commonly used
include precast concrete panels, prefabricated metal sheets and plates, welded
10-1
EM 1110-2-2502
29 Sep 89
wire mesh, inclusion of intermediate reinforcements between main reinforcement

layers at the face, and seeding of the exposed soil.
b. Basic Mechanisms and Behavior. The two primary mechanisms of stress

transfer between the reinforcement and soil are friction between plane contact
surface areas and passive soil-bearing resistance on reinforcement surfaces
oriented transverse to the direction of movement. Strip, sheet, and rod rein-
forcements transfer stresses to the soil by friction, while grid reinforcements
transfer stresses primarily by passive resistance. Geogrid reinforcements
develop both frictional and passive soil resistance.
c. Strip Reinforcement. With strip reinforcement, a mechanically sta-

bilized backfill is created by placing strips in horizontal planes between
successive lifts of soil backfill. Reinforced earth, shown schematically in
Figure 10-1, is a strip reinforcement system.
d. Grid Reinforcement. Grid reinforcement systems are formed by placing

metallic or polymeric tensile resistant elements in horizontal planes in the
soil backfill. Retaining walls using bar-mesh reinforcement have been con-
structed by the California Department of Transportation, Hilfiker Retaining
Walls; VSL Corporation, and the Georgia State Highway Department (see Fig-
ures 10-2 and 10-3) . Grid reinforcements are also made of polymer materials,
such as Tensar Geogrid (see Figure 10-4).
10-5. Advantages and Disadvantages. The advantages and disadvantages of

mechanically stabilized backfill systems are outlined below (Mitchell and
Villet 1986).
a. Advantages.
(1) Mechanically stabilized backfill systems are economical when compared

to conventional retaining walls.
(2) Construction of mechanically stabilized backfill systems usually is

easy and rapid. It does not require skilled labor or specialized equipment.
Many of the components are prefabricated allowing relatively quick
construction.
(3) Regardless of the height or length of the wall, the structure remains
stable during construction.
(4) When compared to conventional retaining walls, mechanically stabil-

ized backfill systems are relatively flexible and can tolerate large lateral
deformations and large differential vertical settlements (when this is antici-
pated, vertical sliding joints can be installed at intervals to compensate for
movement). The flexibility of mechanically stabilized backfill systems allows
the use of a lower factor of safety for bearing capacity design than conven-
tional more rigid structures.
10-2
EM 1110-2-2502
29 Sep 89
•;-v ■ CO
*\ &
» \"
1
.' ■■■■■:
c
,,•
- 5;
£*r ■" -v.
.•*•■' 'Xi i:
i c
•H
■*.ff .:•.•■ .'■;..
CO
"• ^ ■»..-—::>-^ •
4J
-• * 35 ■'■».' ;'>?..'■'■'*'■
?
-4" « , * ;
• *—l".i.. *. *'■• -:" JS
■' ,u.'::'., .--„■ ■-. ■u
1-1
* *•:«■■"'•■■.:. CO
■' **■ ■■■'.-■■- ■'.; '*■'
,. ü
.■<*..' ■' ■;?*~,:: ai
» OQ * .'•■■''
\ • ' ■" • *o
01
■ \ * • . ' *
u
o
«t-i
c
•H
k. . ■ > « - . ' »'
<D
. « 1
' >■ ■■ ■■ > . '.
H
« * ♦ ■•:.
... _ ■.,:,..■ -.
«4-1
* ■ '
o
■«-'■■ ^-- ■• ■»
B
CO
"■ ■'"♦■: *'■"?: V-;:' *
••. ••■■ •■
CO
*a
0)
o
CO
I
o
cu
3
00
1-1
10-3
EM 1110-2-2502
29 Sep 89
■ CAP PANEL
VERTICAL JOINT
BAR MESH
REINFORCEMENT
NEOPRENE BEARING PAD
STYROFOAM BEARING PAD
HALF PANEL
FULL PANEL
CONNECTING PIN
LEVELING COURSE PANEL
Figure 10-2. Schematic diagram of reinforced soil embankment retaining

wall (after Hilfiker Company)
10-4
EM 1110-2-2502
29 Sep 89
COPING ■
"REINFORCING
FACING PANEL- MESH
GRANULAR
BACKFILL
LEVELING PAD
Figure 10-3. VSL retained earth retaining wall (adapted from

VSL Corporation 1984)
(5) Mechanically stabilized backfill systems are potentially better

suited for earthquake loading than conventional retaining walls because of the
flexibility and inherent energy absorption capacity of the coherent earth mass.
In designing mechanically stabilized backfill systems for earthquake regions,
provision should be made for slippage of reinforcement elements rather than
tension failure of the elements, resulting in a ductile structure (McKittrick
1979).
(6) Mechanically stabilized backfill systems, because of their flexibil-

ity and mass, are capable of withstanding dynamic loads imposed by wheel loads,
wave action, and impact of small boats.
(7) Polymeric reinforcements are stable under chemical and biological

conditions normally occurring in soils.
(8) Since facing elements play only a secondary structural role, a

greater flexibility is available to meet aesthetic requirements than for con-
ventional retaining walls. Facing arrangements range from concrete panels of
10-5
EM 1110-2-2502
29 Sep 89
RAILWAY TRACKS
DOUBLE TEE
PSC
WALL UNITS
CONCRETE
SLAB
\ :»\o CONCRETE /
p. * > ÂFnSFflT^" ^S£ LIMESTONE LAYER \
TYPICAL TIEBACK/FACING SYSTEM
Figure 10-4. Tensar geogrid retaining wall (adapted from

Tensar Corporation 1984)
10-6
EM 1110-2-2502
29 Sep 89
various shapes, textures, and colors to provision of vegetation at the exposed

face of the soil.
b. Disadvantages.
(1) Corrosion of metallic reinforcement occurs and must be assessed on a

project basis by determining the potential aggressiveness of the soil. Special
coatings such as galvanized zinc and resin-bonded epoxy are used with a
sacrificial thickness of steel added in the design to give the required service
life.
(2) Although polymeric reinforcement is a robust material, some allowance

must be made for decrease in strength due to abrasion during construction.
This will vary with the type of reinforcement material.
(3) Different polymers have different creep characteristics. Allowable

loads in the grid should be selected based on allowable deformations, as well
as the results of creep tests (10,000 hour). See McGown et al., 1985, for
load-strain-time behavior of Tensor geogrids.
(4) The construction of mechanically stabilized embankments in cut

regions requires a wider excavation than conventional retaining walls.
(5) Excavation behind the mechanically stabilized wall is restricted.
10-6. Cost Considerations. Mechanically stabilized backfill systems are

particularly economical when compared to conventional retaining walls for earth
fill situations where the retaining wall has a total surface area greater than
2,000 sq ft, average wall height greater than 10 feet, or where a rigid
conventional wall requires a deep foundation for support. Precast concrete
modular systems are cost-effective compared to conventional retaining walls for
cut sides of excavations where the wall surface area is greater than 500 sq ft
and average wall height is greater than 8 feet. The cost effectiveness of
mechanically stabilized backfill systems will probably be reduced by high-cost
backfill, complicated horizontal alignment, or the necessity of providing
temporary excavation support systems during construction. For excavated side
slopes, mechanically stabilized backfill systems can be constructed for 30 to
50 percent less than conventional retaining walls. However, a short life,
serious consequences of failure, or high repair or replacement costs could
offset a lower first cost. Similar savings in construction time are obtained
using mechanically stabilized backfill systems, according to Leary and
Klinedinst (1984).
10-7. Mechanisms and Behavior. The stability of mechanically stabilized

backfill systems depends on transfer of stresses between the soil and rein-
forcements . Most reinforcements are inextensible in that they rupture at
strains much less than those required to cause soil failure* (Mitchell and
Villet 1986, Mitchell, Villet, and DiMillio 1984).
10-7
EM 1110-2-2502
29 Sep 89
a. Mechanisms. The transfer of stress between soil and reinforcement is

by friction and/or passive soil resistance when the reinforcement is loaded in
tension. In many reinforcement systems both mechanisms are present, and the
relative contribution of each is indeterminate.
(1) Friction. The load transferred by friction per unit area of rein-
forcement depends on the interface characteristics of the soil and reinforce-
ment, and on the normal stress between them, which in turn depends on the
stress-deformation behavior of the soil. This latter behavior is itself
stress-dependent. Therefore, the effective friction coefficient cannot be
estimated by analytical procedures. The results of experiments such as pullout
tests, direct shear tests between soil and reinforcements, and instrumented
model and full-scale tests, are often used to select friction coefficients.
The coefficient of friction is defined as the average mobilized shear stress
along the reinforcement divided by the normal stress from the overburden
pressure. Empirical data from pullout tests on strip reinforcements show a
decrease in this coefficient with depth regardless of the type of
reinforcement (smooth or ribbed). This occurs because the effective normal
stress is altered by the soil to reinforcement interaction. As shear strains
are imposed on a dense granular soil, the soil tends to dilate. If the ten-
dency to dilate is partially restrained by boundary conditions, local confining
stresses will increase with the tendency to dilate decreasing as the confining
stress increases. Hence, the influence of dilatancy on friction coefficients
computed from pullout tests decreases with depth. Therefore, since the influ-
ence of dilatancy decreases with depth, the coefficient of friction also de-
creases with depth. Also, recent experience in construction with granular
soils of low uniformity coefficients** (less than 4) indicates a relatively low
friction coefficient (=1.0) for these types of granular soils.
(2) Passive Soil Resistance. Passive soil resistance to pullout of

reinforcement develops against bearing surfaces which are normal to the direc-
tion of the pullout force. For grid reinforcing systems with the spacing of
cross bars parallel to the wall equal to or greater than 6 inches, the major
portion of the resistance (approximately 90 percent for bar mesh in a sandy
gravel) is obtained by passive soil resistance or bearing capacity on the front
face of elements oriented transverse to the pullout force direction.
(3) Strain Compatibility. Friction between the soil and a smooth rein-
forcement requires a small displacement of about 0.05 inch. Passive soil
* Some geotextiles, which require large deformations to cause failure, are

the exception.
** D
60
U ~ D
10
where C = coefficient of uniformity
D = grain diameter at 60 percent passing
D = grain diameter at 10 percent passing
10-8
EM 1110-2-2502
29 Sep 89
resistance against surfaces normal to displacement requires relative soil-to-

reinforcement displacements as large as 4 inches for complete mobilization.
However, a significant portion (greater than 50 percent) of the maximum value
is mobilized at deflections of about 0.25 inch (Elias 1986). For bar mat grid
reinforcement systems, the small beneficial effects of friction are neglected
in view of possible strain incompatibility between frictional behavior and pas-
sive soil resistance.
b. Behavior. The distribution of lateral earth pressure within rein-

forced soil depends on the extensibility of the reinforcements, the construc-
tion methods used, and the type of reinforced structure. The active horizontal
stress state is used for systems which are able to undergo relatively large
lateral deformations, such as geotextiles. Higher lateral stresses, such as
at-rest pressures, are associated with less extensible reinforcements, e.g.,
steel strips, bar meshes, welded wire mesh, and relatively low confining
pressures, e.g., at shallow depths in the soil backfill where dilatancy is most
effective. Under low confining stresses a reinforcement system may fail by
pullout between the reinforcement and soil. Under high confining stresses the
same system may fail by breakage of the reinforcements.
10-8. Materials. As previously mentioned, the three basic components of

mechanically stabilized backfill systems are reinforcements, soil backfill, and
facing elements (Mitchell and Villet 1986).
a. Reinforcement. The reinforcements may be characterized by the type of

material (metallic and nonmetallic) and geometry (strips, grids, and sheets).
Important material properties for reinforcements are strength and stability
(low tendency to creep), high coefficient of friction with soil backfill, and
durability. Depending on the electrochemical properties of the soil backfill
and structure environment (marine or freshwater, presence of stray electrical
currents in the ground, etc.) galvanized zinc-coated steel, resin-bonded
epoxy-coated steel, or polymeric reinforcements are used. Polymeric
reinforcements are not subject to corrosion but do exhibit creep charac-
teristics (decrease in strength with time at constant load and soil
temperature).
b. Soil Backfill. Most mechanically stabilized embankment systems have

used cohesionless soil backfill. However, since grid reinforcements have a
much greater pullout resistance than strip reinforcements, it is possible to
construct mechanically stabilized embankment systems using silty or clayey
material as backfill (Forsyth 1979 and Jackura 1984). The advantages of cohe-
sionless soil backfill are that it is stable (will not creep), free-draining,
not susceptible to frost, and relatively noncorrosive to reinforcement. The
main disadvantage, where cohesionless soil has to be imported, is cost. The
main advantage of cohesive soils is availability and hence lower cost. The
disadvantages are long-term durability problems (corrosion and/or frost sus-
ceptibility) and distortion of the structure (due to creep of the soil back-
fill) . When cohesionless soil backfill is readily available it should be
used. When it is not readily available, the costs of importing cohesionless
10-9
EM 1110-2-2502
29 Sep 89
soil backfill should be weighed against the potentially poorer performance of

using the lower-cost locally available cohesive soil backfill.
c. Facing Elements. Since facing elements play only a secondary struc-

tural role, a greater flexibility in choice of materials is available to meet
aesthetic requirements than is the case for conventional retaining walls. A
wide variety of materials, shapes, architectural finishes, and colors are
available for facing elements. Selecting among these depends on the function
of the structure, type of reinforcement, and aesthetics.
10-9. Design Considerations. The various engineering companies involved in a

project provide site-specific designs for their proprietary system. Mechani-
cally stabilized embankment systems must be designed for both external and
internal stability. External stability is evaluated in a manner similar to a
conventional gravity retaining wall. Internal stability depends on there being
neither pullout nor breakage of the reinforcement (Mitchell and Villet 1986,
Collin 1986) .
a. External Stability. The mechanically stabilized backfill system must

be stable against sliding along the base of the structure, overturning about
the toe of the wall, bearing capacity failure of the foundation soil, overall
slope stability, and differential settlement along the structure. For external
stability calculations the mechanically stabilized backfill system is assumed
to behave as a coherent block.
(1) Sliding Along the Base of the Structure. The mechanically stabilized
backfill system must be stable against sliding due to the lateral pressure of
the soil retained by the system. The minimum factor of safety against sliding
should be 1.5. Sliding considerations may govern the design for high
structures (greater than 30 feet) or structures with sloping backfills.
(2) Overturning About the Toe of the Wall. The mechanically stabilized
backfill system must be stable against overturning about the toe of the wall.
Since in reality the structure is flexible, it would probably never fail by
overturning. One hundred percent of the base should always be in contact with
the subgrade for all loading conditions (Elias 1986) . Overturning considera-
tions seldom govern the design of structures when the minimum reinforcement
length is 70 percent of the wall height.
(3) Bearing Capacity Failure and Settlement. The mechanically stabil-

ized backfill system must be stable against bearing capacity failure of the
foundation soil. The minimum factor of safety against bearing capacity fail-
ure should be 2.0. This is lower than that used for conventional retaining
walls (see Table 4-1) because of the flexibility of the mechanically stabil-
ized backfill system and its ability to function satisfactorily after experi-
encing large differential settlements. If the foundation does not meet
stability requirements, consideration should be given to ground improvement
techniques such as stone columns, vibroflotation, and dynamic compaction to
improve foundation stability. The maximum allowable differential settlement
of mechanically stabilized backfill systems is limited by the longitudinal
10-10
EM 1110-2-2502
29 Sep 89
deformability of the facing and the purpose of the structure. For precast
concrete panels, without built-in vertical joints,* the limiting tolerable
differential settlement is 1 foot per 100 feet of wall length.
(4) Overall Slope Stability. The mechanically stabilized backfill sys-

tems, retained soil, and foundation should be stable against slope failure.
All potential slip surfaces should be investigated including those passing
through the reinforcement and deep-seated sliding. The minimum factor of
safety for slope stability should be 1.5.
b. Internal Stability. The mechanically stabilized backfill system must

be stable against reinforcement pullout and reinforcement breaking.
(1) Reinforcement Pullout. In determining the reinforcement pullout

capacity, the effective length of reinforcement behind the theoretical failure
surface must be great enough to assure the transfer of stress from the rein-
forcement to the backfill soil without reinforcement pullout. The resistance
to pullout may be frictional (strip reinforcement), passive (bar mesh rein-
forcement) , or frictional-passive (Geogrid). Using data from laboratory pull-
out tests at a maximum of 0.75 inch of deformation, the structure should be
designed with a minimum factor of safety against reinforcement pullout of 1.5
at each reinforcement level.
(2) Reinforcement Breaking. To assure a sufficient reinforcement break-

ing capacity, the effective cross-sectional area of the reinforcement (cor-
rected for corrosion effects over the design life of the structure) must be
great enough to allow for the transfer of stress from the reinforcement to the
backfill soil without the reinforcement breaking. The design stress in the
reinforcement should be taken as 55 percent of the yield stress (Elias 1986).
(3) Durability of Reinforcements. The durability of reinforcements,

over the design life of the structure, is an important design consideration.
Deterioration of polymeric reinforcements may occur due to abrasion during
construction and decrease in strength with time at constant load and soil
temperature. Corrosion of metallic reinforcement occurs due to exposure to
air, water, and chemicals in the soil backfill. Galvanized zinc-coated steel
(with a sacrificial thickness of steel added to give the required service life)
is often used for reinforcing mild to moderately corrosive soil backfill with
the following properties** (Frondistou-Yannas 1985).
Resistivity > 3,000 ohm-centimetres
pH 5-10
Hilfiker Reinforced Soil Embankment retaining walls have vertical joints

built into the wall every 12.5 feet and can tolerate large differential
settlements.
Galvanized zinc-coated steel should not be used if the soil backfill
contains illite clay because zinc is sensitive to illite.
10-11
EM 1110-2-2502
29 Sep 89
Chlorides < 200 parts per million
Sulfates < 1,000 parts per million
For mild to moderately corrosive soil backfills the corrosion loss rates are:
Galvanization 6 |im/year for first 2 years
2.5 um/year for subsequent years
Steel 9 nm/year after all zinc is lost
The use of aluminum and stainless steel reinforcement is not recommended as

several failures have occurred using these materials (McGee 1985) . For struc-
tures exposed to marine environments, stray electrical currents in the ground,
or with soil backfill properties outside the electrochemical guidelines previ-
ously given, resin-bonded epoxy-coated metallic reinforcements or a conven-
tional or precast concrete modular gravity wall should be used. A minimum
epoxy coating thickness of 18 mils is necessary to survive transportation and
installation, and to provide an acceptable level of design confidence. When
epoxy-coated metallic reinforcement is used, the soil backfill should consist
of rounded stone with a maximum particle size of 1 inch. For design purposes,
the life of the epoxy coating should be assumed to be the same as a galvanized
zinc coating of 2 oz/sq ft, or 30 years. A sacrificial thickness of steel
should be added to provide the epoxy-coated reinforcement an adequate factor of
safety at the design life of the structure (Frondistou-Yannas 1985, Jones
1985).
c. Drainage. Drainage measures must be considered for all mechanically

stabilized backfill systems to prevent saturation of the soil backfill and to
intercept surface flows containing aggressive elements such as deicing chemi-
cals. When mechanically stabilized backfill systems support roadways which are
chemically deiced in the winter, an impervious membrane should be placed
between the pavement and the first row of metallic reinforcements to intercept
any surface flows containing aggressive chemicals.
10-10. Construction Considerations. The construction of mechanically stabil-

ized embankment systems does not require specialized contractors, skilled
labor, or special equipment. Many of the components are prefabricated, provid-
ing ease of handling and forming and relatively quick construction. A small
crane is used to handle and erect precast concrete facing panels. Front end
loaders are used for loading dump trucks and spreading the soil backfill.
Vibratory rollers are used to compact the soil backfill while small hand-
operated compactors are used for compaction near the wall face. Preparation of
the construction area consists of clearing vegetation, debris, and other
deleterious material from the site. A concrete leveling pad, which is not a
structural member, is constructed to facilitate the erection of the concrete
panels. The first layer of soil backfill is placed and compacted and the
reinforcement is laid on the surface of the compacted fill and covered with
the next layer of fill. Construction equipment must not run on top of the
10-12
EM 1110-2-2502
29 Sep 89
reinforcement. Concrete panels are battered to the inside to compensate for

the small outward movement to mobilize the resistance of the reinforcement.
Filler material (cork, styrofoam, neoprene, etc.) is used between all hori-
zontal joints to provide a uniform bearing surface between adjacent panels. A
geotextile is placed over all joints on the fill side of the concrete panels to
prevent fines from migrating from behind the wall (Mitchell and Villet 1986).
10-11. Instrumentation and Monitoring. The history of mechanically stabilized

embankment systems is relatively short compared to the design life of the
structure.* Therefore, continued accumulation of field data on a full-scale
structure is necessary to verify design assumptions. Structures should be
instrumented and monitored whenever atypical conditions exist such as cohesive
soil backfill, epoxy-coated metallic reinforcement, or adverse groundwater
conditions (outside the range specified in paragraph 10-9b(3)). Measurements
should be made of horizontal and vertical displacements of the wall facing;
soil pressures on the facing or on a vertical plane near the facing, the base
of the wall, and perpendicular planes (horizontal and vertical) along the
anticipated maximum tensile force line; tensile forces in the reinforcement
including near the locus of maximum tensile force and near the wall facing; and
pullout tests on short reinforcements. All mechanically stabilized embankment
structures should be monitored once they are placed in operation to ensure
stability. External stability of the mechanically stabilized embankment
structure could be threatened by the same factors as a conventional retaining
wall; e.g., clogging of the drainage system, erosion at the toe of the wall,
etc. However, the mechanically stabilized embankment system could also fail
due to changes in conditions which adversely influence the internal stability
of the system. These include excavation within the soil backfill, changes in
the groundwater conditions (outside the range specified in paragraph 10-9b(3)),
and possible damage to the stabilizing ties because of vandalism to the exposed
structure (Mitchell and Villet 1986, Al-Hussani and Perry 1978).
10-12. Maintenance and Repair. Since mechanically stabilized embankment

systems are relatively new there is very limited field experience regarding
maintenance and repair. Maintenance problems arising with facing elements
could be repaired by conventional methods since the facing elements play a
secondary role and resist only small horizontal earth pressures (Long et al.
1984). However, problems with the reinforcements, such as corrosion of
metallic reinforcements, would be difficult to repair. One possible solution
would be to use soil nailing to stabilize the structure (Jones 1985) . Another
method would be to place a stone buttress in front of the structure (Mitchell
and Villet 1986).
Strip reinforcement was first utilized in U.S. construction in 1972, bar

mesh reinforcement in 1975, and Geogrid reinforcement in 1984.
10-13
EM 1110-2-2502
29 Sep 89
Section III. Precast Concrete Modular Systems
10-13. Background. Precast concrete modular systems consist of interlocking

soil-filled reinforced concrete modules which form a gravity retaining wall.
They can be erected rapidly and are cost-competitive with mechanically
stabilized backfill systems.*
10-14. Basic Components. The basic components of precast concrete modular

systems are interlocking precast reinforced concrete modular elements filled
with soil and resting on natural soil or a concrete foundation (see Fig-
ures 10-5 to 10-8) . Some systems have resets or an open-face structure at the
wall face (see Figures 10-7 and 10-8) with evergreen vegetation to reduce noise
levels and eliminate the problem of graffiti.
10-15. Advantages and Disadvantages. The advantages and disadvantages of

precast concrete modular systems are listed below.
a. Advantages.
(1) Modular systems are economical when compared to conventional retain-

ing walls in cut situations, particularly where the retaining wall has a total
surface area greater than 500 sq ft and average wall heights greater than
8 feet.
(2) Assembly of the wall components requires no fasteners and the modules
may be reused easily and economically.
(3) The precast concrete modular retaining wall does not utilize rein-
forcing elements and therefore is not subject to corrosion damage.
(4) Excavation behind the precast concrete modular retaining wall does
not adversely influence the stability of the system as might occur for the
mechanically stabilized wall.
b. Disadvantage. The precast concrete modular retaining wall could

sustain cracking of interior connecting members due to relatively small
(0.5 foot per 100 feet of wall length) longitudinal differential settlement.
10-16. Design Considerations. Various engineering companies involved will

provide site-specific plans and limited designs for their proprietary system.
Stability is evaluated in a manner similar to a conventional gravity retaining
wall. For stability calculations the interlocking precast concrete modular
system is assumed to behave as a coherent block. The system must be stable
* For certain applications, such as where large differential vertical

settlements are anticipated, consideration should be given to steel-bin
type retaining walls which are generally more expensive than mechanically
stabilized backfill or precast concrete modular systems but less expensive
than conventional retaining walls.
10-14
EM 1110-2-2502
29 Sep 89
TOP KEY BEAM
LIFTING HOLE
■FOOTING TYPICAL BOTTOM MODULE - D
Figure 10-5. Schematic diagram of Doublewal retaining wall

(after Doublewal Corporation 1984)
10-15
EM 1110-2-2502
29 Sep 89
C
•d&
60
a
•H
cd
u
0)
u
a
-a-
00
3 o\
Ö -*
a
ß
■U O
u •rt
■u
«3
4-1 H
CO O
D.
go *•!
Q
a
o
*J
-ö
<u
CO
3
4J
«8
I
o
u
a
60
■H
10-16
EM 1110-2-2502
29 Sep 89
■£%'
FALSE HEADER -J& ANGLE OF SURCHARGE
.aOW^
c\AV"^ _f __ ___ __ __ _
LEVEL FILL'
FRONT STRETCHER
HEADER
DOUBLE DEPTH WALL
COMPACTED GRANULAR
^BACKFILL
TREBLE DEPTH WALL
NOTE: FALSE HEADERS ARE

NOT USED IN THE INTERIOR
SECTIONS OF MULTIPLE
DEPTH WALLS.
MULTIPLE DEPTH WALL (TYPICAL)
NO SCALE
1'-3".
WALL ELEVATION (TYPICAL)

NO SCALE .
Figure 10-7. Schematic diagram of Criblock retaining wall

(after Criblock Retaining Walls of America)
10-17
EM 1110-2-2502
29 Sep 89
RETAINING WALL
FOUNDATION DIMENSIONS
a - TRENCH WIDTH
b - LENGTH
c - LEDGE
d ■= DEPTH
f = FROST DEPTH
P = PEDESTAL OR PIER
F - FOOTINGS
tD m m üi in ci^ra-ifr
INDIVIDUAL OF CONTINUOUS FOOTINGS F
S'-8" 6'-8" 6'-3"

PLAN VIEW
2<y 20'
Figure 10-8. Schematic diagram of Evergreen retaining wall

(after Evergreen Systems, Inc.)
10-18
EM 1110-2-2502
29 Sep 89
against sliding along the base of the structure, overturning about the toe of
the wall, bearing capacity failure of the foundation soil, differential set-
tlement, and overall slope stability.
a. Sliding Along The Base Of The Structure. The precast concrete modular
system must be stable against sliding due to the lateral pressure of the soil
retained by the system. The minimum factor of safety against sliding should be
1.5.
b. Overturning About The Toe Of The Wall. The precast concrete modular
system must be stable against overturning about the toe of the wall. Since the
concrete modular units are not tied together vertically, the stability against
overturning must be checked at each concrete module level for a given width.
One hundred percent of the base should always be in contact with the subgrade
for all loading conditions (Elias 1986). Normally overturning (not sliding)
criteria govern the design.
c. Bearing Capacity Failure and Settlement. The precast concrete modular

system must be stable against bearing capacity failure of the foundation soil.
The minimum factor of safety against bearing capacity failure should be 3.0
(Elias 1986) . If the foundation does not meet stability requirements,
consideration should be given to use of a mechanically stabilized backfill
system or ground improvement techniques such as stone columns, vibroflotation,
and dynamic compaction to improve foundation stability. As previously stated,
the precast concrete modular retaining wall could sustain cracking of interior
connecting members due to relatively small (0.5 foot per 100 feet of wall
length) longitudinal differential settlement. Precast concrete modular re-
taining walls are also susceptible to damage from differential settlement
perpendicular to the wall face, particularly on high walls where the bottom
wall units may be as wide as 20 feet.
d. Overall Slope Stability. The precast concrete modular system, re-

tained soil, and foundation should be stable against slope failure. All
potential slip surfaces should be investigated including deep-seated sliding.
The minimum factor of safety for slope stability should be 1.5.
e. Drainage. Drainage measures must be considered for all precast con-

crete modular systems to prevent saturation of the soil backfill. Also, for
closed-face modular systems (see Figure 10-5), a geotextile is placed over all
joints on the back side of the front face of the wall to prevent fines from
migrating from behind the wall.
10-17. Construction Considerations. The construction of precast concrete

modular systems does not require specialized contractors, skilled labor, or
special equipment. The components are prefabricated providing ease of handling
and forming and relatively quick construction. Soil backfill within the pre-
cast modular units should receive adequate compaction to minimize post-
construction settlements.
10-19
EM 1110-2-2502
29 Sep 89
10-18. Instrumentation and Monitoring. The history of precast concrete

modular systems is relatively short compared to the design life of the struc-
ture.* Therefore, continued accumulation of field data is necessary to verify
design assumptions. Structures should be instrumented and monitored whenever
atypical conditions exist such as anticipated large differential vertical
settlement. Measurements should be made of horizontal and vertical displace-
ments of the front face of the wall and soil pressures on the rear face of the
wall. All precast concrete modular structures should be monitored once they
are placed in operation to ensure stability. Stability of the precast concrete
modular structure could be threatened by the same factors as a conventional
retaining wall; e.g., clogging of the drainage system, erosion at the toe of
the wall, etc. Precast concrete modular structures should also be monitored
for possible damage from differential settlements.
10-19. Maintenance and Repair. Since precast concrete modular structures are
relatively new, there is very limited field experience regarding maintenance
and repair. Possible methods of repair to a section of the structure which has
sustained damage from differential settlement include replacing the section
with a wall more tolerant to differential settlement, such as a mechanically
stabilized embankment system with vertical joints (see Figure 10-2) or a
steel-bin type wall, or placing a stone buttress in front of the structure.
Criblock was first used in US construction in 1978, Doublewal in 1979, and

Evergreen in 1986.
10-20
EM 1110-2-2502
29 Sep 89
APPENDIX A
REFERENCES
Government Publications
Department of the Army, Corps of Engineers*
Engineer Regulations
ER 1110-1-803 Constructibility
ER 1110-2-100 Periodic Inspection and Continuing

Evaluation of Completed Civil Works
Structures
ER 1110-2-1806 Earthquake Design and Analysis for

Corps of Engineers Projects
ER 1130-2-339 Inspection of Local Flood Protection

Projects (RC5 DAEN-CWC-40)
Technical Manuals
TM 5-818-1 Soils and Geology: Procedures for

Foundation Design of Buildings and
Other Structures (Except Hydraulic
Structures)
Engineer Manuals
EM 1110-1-1804 Geotechnical Investigations
EM 1110-1-2101 Working Stresses for Structural Design
EM 1110-1-2009 Architectural Concrete
EM 1110-2-301 Landscape Planting at Floodwalls,

Levees & Embankment Dams
EM 1110-2-1410 Interior Drainage of Leveed Urban

Areas: Hydrology
EM 1110-2-1601 Hydraulic Design of Flood Control

Channels
* Available from: Corps of Engineers Publication Depot, 2803 52nd Avenue,

Hyattsville, MD 20781.
A-l
EM 1110-2-2502
29 Sep 89
EM 1110-2-1901 Soil Mechanics Design - Seepage

Control
EM 1110-2-1902 Stability of Earth and Rock-Fill Dams
EM 1110-2-1903 Bearing Capacity of Soils
EM 1110-2-1904 Soil Mechanics Design - Settlement

Analysis
EM 1110-2-1905 Design of Finite Relief Well Systems
EM 1110-2-1906 Laboratory Soil Testing
EM 1110-2-1907 Soil Sampling
EM 1110-2-1908 Instrumentation of Earth and Rock-Fill

Dams (Ground-Water & Pore Pressure
Observations) (Part 1)
EM 1110-2-1911 Construction Control for Earth and

Rockfill Dams
EM 1110-2-1913 Design and Construction of Levees
EM 1110-2-2000 Standard Practice for Concrete
EM 1110-2-2102 Waterstops and Other Joint Materials
EM 1110-2-2103 Details of Reinforcement - Hydraulic

Structures
EM 1110-2-2906 Design of Pile Structures and

Foundations
EM 1110-2-4300 Instrumentation for Concrete

Structures
EM 1120-2-109 Federal Participation in Major

Drainage Improvements
Guide Specifications
CW 02215 Plastic Filter Fabric
CW 03301 Cast-in-Place Structural Concrete
CW 03305 Mass Concrete
A-2
EM 1110-2-2502
29 Sep 89
Agostinelli, V. M., et al. 1981 (Feb). "Program Criteria Specifications

Document for Computer Program TWDA for Design and Analysis of Inverted-T
Retaining Walls and Floodwalls." Available from: U. S. Army Engineer
Waterways Experiment Station, P. 0. Box 631, Vicksburg, MS 39180.
Al-Hussani, M. M., and Perry, E. B. 1976 (Sep). "Effect of Horizontal Rein-

forcement on Stability of Earth Masses," Technical Report S-76-11, U. S.
Army Engineer Waterways Experiment Station, P. 0. Box 631, Vicksburg, MS
39180.
Al-Hussani, M. M., and Perry, E. B. 1978 (Mar). "Field Experiment of Rein-

forcement Earth Wall," Journal of the Geotechnical Engineering Division,
ASCE, Vol 104, No. GT3, pp 307-322. Available from: U. S. Army Engineer
Waterways Experiment Station, P. 0. Box 631, Vicksburg, MS 39180.
American Concrete Institute. "Building Code Requirements for Reinforced

Concrete," ACI 318, Detroit, Mich. Available from: American Concrete
Institute, P. O. Box 19150, Redford Station, Detroit, MI 48219.
American Concrete Institute. 1967. "Ultimate Strength Design Handbook, ACI

Publication SP-17. Available from: American Concrete Institute,
P. 0. Box 19150, Redford Station, Detroit, MI 48219.
ANSI A58.1. Minimum Design Loads for Buildings and Other Structures, American
National Structures Institute, Inc., 1430 Broadway; New York, NY 10018.
Applied Technology Council (ATC). 1981 (Oct). Seismic Design Guidelines for
Highway Bridges, FHWA Report No. FHWA/RD-81/081. Available from: NTIS,
Springfield, VA 22161.
ASTM D 1586. "Standard Method for Penetration Test and Split-Barrel Sampling
of Soils." Available from: ASTM, 1916 Race St., Philadelphia, PA
19103.
ASTM D 3441-79. "Standard Method for Deep Quasi-Static, Cone and Friction-
Cone Penetration Tests of Soil." Available from: ASTM, 1916 Race St.,
Philadelphia, PA 19103.
Baguelin, F., Jezeguel, J. F., and Shields, J. F. 1978. The Pressuremeter

and Foundation Engineering, Trans-Tech Publications, Rockport, MA.
Bowles, J. E. 1982. Foundation Analysis and Design, 3rd ed., McGraw-Hill,

New York.
Brooker, E. W., and Ireland, H. 0. 1965 (Feb). "Earth Pressures At-Rest

Related to Stress History," Canadian Geotechnical Journal, Vol 2, No. 1,
pp 1-15.
A-3
EM 1110-2-2502
29 Sep 89
Caquot, A., and Kerisel, J. 1948. Tables for the Calculation of Passive
Pressure, Active Pressure, and Bearing Capacity of Foundations (trans-
lated by M. A. Bee, London), Gauthier-Villars, Paris.
Carroll, R. G., Jr., and Murphy, J. C. 1985 (May-Jun). "Drainage Objective:

Prefabricated Drainage Composites," Geotechnical Fabrics Report, Vol 3,
No. 3, pp 14-18.
Casagrande, A. 1937. "Seepage Through Dams," Contributions to Soil

Mechanics, 1925-1949, Boston Society of Civil Engineers, Boston, MA,
pp 295-336.
Casagrande, Leo. 1973 (Feb). "Comments of Conventional Design of Retaining

Structures," Journal, Soil Mechanics and Foundations Division, American
Society of Civil Engineers, Vol 99, No. SM 2, pp 181-197. Available
from: ASCE Publication Fulfillment, 345 East 47th Street, New York, NY
10017.
Cedergren, Harry R. 1967. Seepage, Drainage, and Flow Nets, John Wiley and
Sons, New York.
Collin, J. C. 1986 (May). "Earth Wall Design," Ph.D. Dissertation, Univer-

sity of California, Berkeley. Available from: University Microfilms
International, 300 North Zeeb Road, Ann Arbor, MI 48106.
Criblock Retaining Walls of America, Inc. "Criblock Interlocking Concrete

Criblock." Available from: Criblock Retaining Wall of America, Inc.,
P. O. Box 849, Sierra Madre, CA 91024.
Danish Geotechnical Institute. 1978. "Code of Practice for Foundation Engi-

neering," Danish Geotechnical Institute, Copenhagen, Denmark, Bulletin
No. 32, p 52.
Das, B. M. 1984. Principles of Foundation Engineering, Brooks/Cole Engineer

ing Division, Monterey, CA.
Department of the Navy. 1982a (May). "Soil Mechanics," NAVFAC DM-7.1.

Available from: Department of the Navy, Naval Facilities Engineering
Command, 200 Stovall St., Alexandria, VA 22332.
Department of the Navy. 1982b (May). "Foundations and Earth Structures,"

NAVFAC DM-7.2. Available from: Department of the Navy, Naval Facilities
Engineering Command, 200 Stovall St., Alexandria, VA 22332.
Doublewal Corp. 1984. "Doublewal Interlocking Precast Retaining Wall System

Field Manual." Available from: Doublewal Corp., 59 East Main St.,
Plainville, CT 06062.
A-4
EM 1110-2-2502
29 Sep 89
Driscoll, D. D. 1979 (Dec). Retaining Wall Design Guide, Foundation Ser-

vices, Inc., Portland, OR, Prepared for USDA Forest Service. Available
from: USDA Forest Service Region 6, 319 S.W. Pine St., Portland, OR
97208.
Duncan, J. M., and Buchignani, A. L. 1976 (Jun). "An Engineering Manual for
Settlement Studies," Department of Civil Engineering, University of
California, Berkeley.
Elias, V. 1986. "Retaining Walls," Draft Bridge Design Manual, Part 4,

Structures, Section 5, Pennsylvania Department of Transportation.
Available from: V. Elias and Associates, 6809 Carlynn Court, Bethesda,
MD 20817.
Evergreen Systems, Inc. "Retaining Walls." Available from: Evergreen

Systems, Inc., P. 0. Box 345, Kings Point, NY 11754.
Forsyth, R. A. 1979. "Alternate Earth Reinforcements," Proceedings, Sym-

posium on Earth Reinforcement, American Society of Civil Engineers,
pp 358-370. Available from: U. S. Army Engineer Waterways Experiment
Station, P. 0. Box 631, Vicksburg, MS 39180.
Frondistou-Yannas, S. 1985 (Jan). "Corrosion Susceptibility of Internally

Reinforced Soil Retaining Structures," Report No. FHWA-RD-83-105, U. S.
Department of Transportation, Federal Highway Administration. Available
from: Federal Highway Administration, Turner-Fairbank Highway Research
Center, 6300 Georgetown Pike, McLean, VA 22101.
Geotechnical Control Office. 1982 (Jun). Guide to Retaining Wall Design,

Geoguide 1, Engineering Development Department, Hong Kong. Available
from: U. S. Army Engineer Waterways Experiment Station, P. 0. Box 631,
Vicksburg, MS 39180.
Godfrey, K. A., Jr. 1984 (Dec). "Retaining Walls: Competition or Anarchy?",

Civil Engineering, Vol 54, No. 12, pp 48-52. Available from: U. S. Army
Engineer Waterways Experiment Station, P. 0. Box 631, Vicksburg, MS
39180.
Harr, M. E. 1977. Mechanics of Particulate Media, McGraw-Hill, New York.

Available from: McGraw-Hill International Book Company, 1221 Avenue of
the Americas, New York, NY 10020.
Harr, M. E. 1962. Groundwater and Seepage, McGraw-Hill, New York.
Hilfiker Company. "R. S. E. Construction Guide." Available from: Hilfiker

Company, 3900 Broadway, Eureka, CA 95501.
Ingold, T. S. 1979a. "Retaining Wall Performance During Backfilling,"

Journal, Geotechnical Engineering Division, American Society of Civil
Engineers, Vol 105, No. GT5, pp 613-626.
A-5
EM 1110-2-2502
29 Sep 89
Ingold, T. S. 1979b. "The Effect of Compaction on Retaining Walls,"

Geotechnique, Vol 29, No. 3, pp 265-283.
Ireland, H. 0. 1964 (Aug). "Design and Construction of Retaining Walls,"

Design of Structures to Resist Earth Pressure, Soil Mechanics Lecture
Series, Department of Civil Engineering, Illinois Institute of Technol-
ogy, Chicago, IL. Available from: U. S. Army Engineer Waterways Exper-
iment Station, P. 0. Box 631, Vicksburg, MS 39180.
Jackura, K. A. 1984 (May). "Results of Minor Research on Bar-Mat Pullout

Tests," CA/TL-84-08, California Department of Transportation, Sacramento,
CA.
Jaky, J. 1944. "The Coefficient of Earth Pressure At-Rest," Journal, Society

of Hungarian Architects and Engineers, Budapest, Hungary, pp 355-358.
Jones, C. J. F. P. 1985. Earth Reinforcement and Soil Structures,

Butterworths, London. Available from: U. S. Army Engineer Waterways
Experiment Station, P. 0. Box 631, Vicksburg, MS 39180.
Kenney, T. C. 1959. Discussion of "Geotechnical Properties of Glacial

Clays," by T. H. Wu, Journal of the Soil Mechanics and Foundations Divi-
sion, ASCE, Vol 85, No. SM3, pp 67-79.
Kraemer, S. R., and Smith, A. D. 1986 (Oct). "Geocomposite Drains," Vol I,

Engineering Assessment and Preliminary Guidelines, Report No. FHWA-RD-
86-171, U. S. Department of Transportation, Federal Highway Administra-
tion. Available from: Federal Highway Administration, 6300 Georgetown
Pike, McLean, VA 22101.
Leary, R. M., and Klinedinst, G. L. 1984 (May). "Retaining Wall Alternates,"

Proceedings, 34th Annual Highway Geology Symposium, Atlanta, GA. Avail-
able from: Federal Highway Administration, Geotechnical and Materials
Branch, 400 7th St., S.W., Washington, DC 20590.
Liu, Tony C, and Gleason, Scott. 1981 (Dec). "Strength Design of Reinforced
Concrete Hydraulic Structures," Technical Report SL-80-4, U. S. Army
Engineer Waterways Experiment Station, Vicksburg, MS. Available from:
US Army Engineer Waterways Experiment Station, P. 0. Box 631, Vicksburg,
MS 39180.
Long, N. T., et al. 1984 (May). "Repair of a Reinforced Earth Wall," Pro-
ceedings, International Conference on Case Histories in Geotechnical
Engineering, Vol 1, pp 335-339, University of Missouri-Rolla, Rolla, MO.
Available from: U. S. Army Engineer Waterways Experiment Station, P. 0.
Box 631, Vicksburg, MS 39180.
Marcuson, W. F., and Bieganousky, W. A. 1977 (Nov). "SPT and Relative Den
sity in Coarse Sands," Journal of the Geotechnical Engineering Division,
ASCE, Vol 103, No. GT11, pp 1295-1309.
A-6
EM 1110-2-2502
29 Sep 89
Massarsch, K. R. 1979. "Lateral Earth Pressure in Normally Consolidated

Clays," Proceedings of the Seventh European Conference on Soil Mechanics
and Foundation Engineering, Brighton, England, Vol 2, pp 245-249.
Matsuo, M., Kenmochi, S., Yagi, H. 1978 (Sep). "Experimental Study on Earth
Pressure of Retaining Wall by Field Tests," Soils and Foundations,
Japanese Society of Soil Mechanics and Foundation Engineering, Vol 18,
No. 3, pp 27-41. Available from: Japanese Society of Soil Mechanics and
Foundation Engineering, Suga-yama Building-4F, Kanda Awaji-cho 2-23
Chiyoda-ku, Tokyo 101, Japan.
McGee, P. E. 1985 (Nov). "Reinforced Earth Wall Strip Serviceability Study,"

Special Research Study No. 8405, Geotechnical Engineering Bureau, Office
of Materials and Research, Georgia Department of Transportation, Forest
Park, GA. Available from: Engineering Design Unit, Georgia Department
of Transportation, Office of Materials and Research, 15 Kennedy Drive,
Forest Park, GA 30050.
McGown, A., et al. 1985. "The Load-Strain-Time Behavior of Tensor Geogrids,"

Proceedings, Conference on Polymer Grid Reinforcement, pp 11-17, Thomas
Telford Ltd., London. Available from: U. S. Army Engineer Waterways
Experiment Station, P. O. Box 631, Vicksburg, MS 39180.
McKittrick, D. 1979. "Design Construction, Technology, and Performance of

Reinforced Earth Structures," Proceedings, Symposium on Earth Reinforce-
ment, American Society of Civil Engineers, pp 596-616. Available from:
U. S. Army Engineer Waterways Experiment Station, P. 0. Box 631,
Meyerhof, G. G. 1956. "Penetration Tests and Bearing Capacity of Cohesion-

less Soils," Journal of the Soil Mechanics and Foundations Divisions,
ASCE, Vol 82, No. SMI, pp 1-19.
Mitchell, J. K., Villet, W. C. B., and DiMillio, A. F. 1984 (Dec). "Soil

Reinforcement for Stabilization of Earth Slopes and Embankments," Public
Roads, U. S. Department of Transportation, Vol 48, No. 3, pp 88-95.
Available from: U. S. Army Engineer Waterways Experiment Station,
P. 0. Box 631, Vicksburg, MS 39180.
Mitchell, J. K., and Villet, W. C. B., eds. 1986. "Reinforcement of Earth

Slopes and Embankments," 4 Vols, National Cooperative Highway Research
Program Project 24-2, National Research Council, Transportation Research
Board, Washington, DC. Available from: National Cooperative Highway
Research Program, 2101 Constitution Avenue, N.W., Washington, DC 20418.
Mosher, Reed L., and Pace, Michael E. 1982 (Jun). User's Guide: Computer
Program for Bearing Capacity Analyses of Shallow Foundations (CBEAR),
Instruction Report K-82-7, U. S. Army Engineer Waterways Experiment Sta-
tion, Vicksburg, MS. Available from: U. S. Army Engineer Waterways
A-7
EM 1110-2-2502
29 Sep 89
Pace, Michael E , Noddin, Virginia R., 1987 (Oct). " Sliding Stability of Con-
crete Structures (CSLIDE)," Instruction Report ITL-87-5 Available from:
Pace, Michael E ., Williams, Dennis R., Wolff, Thomas F., and Mosher, Reed.
1984 (Sep) "Seepage Analysis of Confined Flow Problems by the Method of
Fragments (CFRAG)," Instruction Report K -84-8. Available from:
Peck, R. B., and Bazaraa, A. S. 1969. "Discussion on Settlement of Spread

Footings on Sand," Journal of the Soil Mechanics and Foundations Divi-
Peck, R. B., Hanson, W. E., and Thornburn, T. H. 1974. Foundation Engineer-

ing, 2nd. ed., Wiley, New York.
Robertson, P. K., and Campanella, R. G. 1983. "Interpretation of Cone Pene

tration Tests; Parts I and II," Canadian Geotechnical Journal, Vol 20,
No. 4, pp 718-745. i
Schmertmann, J. H. 1975. "Measurement of In-Situ Strength," Proceedings of

the Conference on In-Situ Measurement of Soil Properties, ASCE,
pp 55-138.
Schwab, G. O., et al. 1981. Soil and Water Conservation Engineering, John
Wiley, New York, 3rd edition. Available from: U. S. Army Engineer
Waterways Experiment Station, P. O. Box 631, Vicksburg, MS 39180.
Seed, H. B. 1976 (Sep). "Evaluation of Soil Liquefaction Effects on Level

Ground During Earthquakes," Liquefaction Problems in Geotechnical Engi-
neering, ASCE annual convention and exposition, Philadelphia, PA, pre-
print 2752, pp 1-104.
Seed, H. B., Arango, I., and Chan, C. K. 1975. "Evaluation of Soil Liquefac
tion Potential During Earthquakes," Report No. EERC 75-28, Earthquake
Engineering Research Center, College of Engineering, University of
California, Berkeley, CA.
Seed, H. B., and Idriss, I. M. 1982. "Ground Motions and Soil Liquefaction
During Earthquakes," Earthquake Engineering Research Institute, Univer-
sity of California, Berkeley, CA.
Seed, H. B., and Whitman, R. V. 1970. "Design of Earth Retaining Structures

for Dynamic Loads," ASCE Specialty Conference, Lateral Stresses in the
Ground and Design of Earth Retaining Structures, pp 103-147.
A-8
EM 1110-2-2502
29 Sep 89
Shields, D. H., and Tolunay, A. Z. 1973. "Passive Pressure Coefficients by-

Method of Slices," Journal of the Soil Mechanics and Foundations Divi-
Sibley, E. A. 1967. "Backfill Adjacent to Structures," Proceedings of the

Montana Conference on Soil Mechanics and Foundation Engineering, Depart-
ment of Civil Engineering, Montana State University, Bozeman, MT.
Available from: U. S. Army Engineer Waterways Experiment Station,
P. O. Box 631, Vicksburg, MS 39180.
Smith, A. D., and Kraemer, S. R. 1987 (Feb). "Creep of Geocomposite Drains,"

Proceedings, Geosynthetic '87 Conference, New Orleans, LA, Vol 2,
pp 422-433. Available from: U. S. Army Engineer Waterways Experiment
Station, P. 0. Box 631, Vicksburg, MS 39180.
Spangler, M. G., and Mickle, J. 1956. "Lateral Pressure on Retaining Walls

Due to Backfill Surface Loads," Highway Research Board Bulletin 141,
pp 1-18.
Tcheng, Y., and Iseux, J. 1972. "Essais de Butee en Vraie Grandeur et Con
straintes Engendrees par une Surcharge Rectangulaire sur un Mur Verti-
cal ," Proceedings, 5th European Conference on Soil Mechanics and Founda-
tion Engineering, Madrid.
Tensar Corp., "Tensar." 1984. Available from: The Tensar Corp., 1210 Citi-
zens Parkway, Morrow, GA 30260.
Terzaghi, K. 1934. "Large Retaining Wall Tests," Engineering News - Record,

Vol 85, February 1--April 19.
Terzaghi, K. 1943. Theoretical Soil Mechanics, John Wiley, New York.
Terzaghi, K., and Peck, R. B. 1948. Soil Mechanics in Engineering Practice,

John Wiley, New York. Available from: U. S. Army Engineer Waterways
Tracy, Fred T. 1977a (Aug). "An Interactive Graphics Finite Element Method
Grid Generator for Two-Dimensional Problems," Miscellaneous Paper K-77-5,
U. S. Army Engineer Waterways Experiment Station, Vicksburg, MS. Avail-
able from: U. S. Army Engineer Waterways Experiment Station,
P. 0. Box 631, Vicksburg, MS 39180.
Tracy, Fred T. 1977b (Aug). "An Interactive Graphics Post-Processor for

Finite Element Method Static Analyses," Miscellaneous Paper K-77-4, U. S.
Army Engineer Waterways Experiment Station, Vicksburg, MS. Available
from: U. S. Army Engineer Waterways Experiment Station, P. O. Box 631,
A-9
EM 1110-2-2502
29 Sep 89
Tracy, Fred T. 1983 (Sep). "User's Guide for a Plane and Axisymmetric Finite
Element Program for Steady-State Seepage Problems," Instruction
Report K-83-4, U. S. Army Engineer Waterways Experiment Station,
Vicksburg, MS. Available from: U. S. Army Engineer Waterways Experiment
Station, P. O. Box 631, Vicksburg, MS 39180.
Tschebatarioff, G. 1949. "Large Scale Earth Pressure Tests with Model Flex-
ible Bulkheads," Final Report to U. S. Navy, Bureau of Yards and Docks,
Princeton University.
U. S. Army Engineer Division, Ohio River. 1958 (Jun). "Final Report on Full-
size Floodwall (T-type) Stability Test." Available from HQUSACE Library.
U. S. Army Engineer Waterways Experiment Station. 1956 (Oct). "Investigation

of Underseepage and Its Control," Technical Memorandum No. 3-424. Avail-
able from: U. S. Army Engineer Waterways Experiment Station, P. 0.
U. S. Army Engineer Waterways Experiment Station. 1960 (Apr). "The Unified

Soil Classification System," Technical Memorandum No. 3-357. Available
from: U. S. Army Engineer Waterways Experiment Station, P. 0. Box 631,
U. S. Army Engineer Waterways Experiment Station. 1962 (Jun). Technical Re

port TR3-604. Engineering Properties of Fine-Grained Mississippi Valley
Alluvial Soils Meander Belt and Blackswamp Deposits. Available from:
U. S. Army Engineer Waterways Experiment Station, P. O. Box 631,
U. S. Army Engineer Waterways Experiment Station. 1980 (Aug). Rock Testing

Handbook, Standard and Recommended Methods. Available from: U. S. Army
Engineer Waterways Experiment Station, P. 0. Box 631, Vicksburg, MS
39180.
U. S. Army Engineer Waterways Experiment Station. 1984. Shore Protection

Manual, Vol 2 of 2, Vicksburg, MS. Available from: Superintendent of
Documents, U. S. Government Printing Office, Washington, DC 20402.
Vesic, A. S. 1975. "Bearing Capacity of Shallow Foundations," Foundation

Engineering Handbook, Hans F. Winterkorn and Hsai-Fang, ed., Van Nostrand
Reinhold Co., New York.
VSL Corporation. 1984. "Retaining Earth." Available from: VSL Corporation,

101 Albright Way, Los Gatos, CA 95030.
Westergaard, H. M. 1933. "Water Pressures on Dams During Earthquakes,"

Transaction, American Society of Civil Engineers, Vol 98, pp 418-433.
Available from: ASCE Publication Fulfillment, 345 East 4th St., New
York, NY 10017.
A-10
EM 1110-2-2502
2 9 Sep 89
Whitman, R. V., and Liao, S. 1985 (Jan). Seismic Design of Gravity Retaining
Walls, Miscellaneous Paper GL-85-1, U. S. Army Engineer Waterways Exper-
iment Station, Vicksburg, MS 39180.
Winterkorn, H. F., and Fang, H-Y., eds. 1975. Foundation Engineering Hand-
book , Van Nostrand-Reinhold, New York.
Wu, T. H. 1966. Soil Mechanics, Allyn and Bacon, Inc., Boston, MA.
A-ll
EM 1110-2-2502
31 Mar 89
APPENDIX B
BIBLIOGRAPHY
Al-Yassin, Z. "Laboratory Pullout Test Results on VSL Retained Earth,"

November 1980. Available from: VSL Corporation, 101 Albright Way,
Los Gatos, CA 95030.
Bang, S. "Active Earth Pressure Behind Retaining Walls," Journal, Geotechni-

cal Engineering, American Society of Civil Engineers, March 1985,
Vol 111, No. 3.
Bishop, J. A., and Anderson, L. A. "Performance of a Welded Wire Retaining

Wall," Dec 1979, Report to Hilfiker Pipe Company, Department of Civil
Engineering, University of Utah, Logan, UT. Available from: U. S. Army
Engineer Waterways Experiment Station, P. O. Box 631, Vicksburg, MS
39180.
Boyd, M. S. "Practical Application of Reinforced Earth Theory," Proceedings,

Symposium on Soil Reinforcing and Stabilizing Techniques in Engineering
Practice, Vol 1, Oct 1978, pp 83-110. Available from: U. S. Army Engi-
neer Waterways Experiment Station, P. 0. Box 631, Vicksburg, MS 39180.
Dawkins, William P. User's Guide: Computer Program for Design and Analysis
of Sheet Pile Walls by Classical Methods (CSHTWAL), U. S. Army Engineer
Waterways Experiment Station, Vicksburg, MS, Instruction Report K-81-2,
February 1981. Available from: U. S. Army Engineer Waterways Experiment
Station, P. O. Box 631, Vicksburg, MS 39180.
Department of the Army, Corps of Engineers. Expansion, Contraction, and Con-

struction Joints in Concrete, Guide Specifications CW 03150. Available
from: Corps of Engineers Publication Depot, 890 South Pickett St.,
Alexandria, VA 22304.
Doublewal Corp. "Doublewal Interlocking Precast Retaining Wall System."

Available from: Doublewal Corp., 59 East Main St., Plainville, CT
06062.
Doublewal Corp. 1982. "Design Manual Doublewall Interlocking Reinforced

Concrete Retaining Wall Systems." Available from: Doublewal Corp.,
59 East Main St., Plainville, CT 06062.
Egan, P. D. "Design and Performance of Reinforced Earth Bridge Abutments,"

Paper presented at First International Bridge Conference, Pittsburgh, PA,
June 1984. Available from: Reinforced Earth Company, Rosslyn Center,
1700 North Moore St., Arlington, VA 22209.
B-l
EM 1110-2-2502
31 Mar 89
Goldberg-Zoino & Associates, Inc. "Report on Full Scale Field Test of Twenty-
Two Foot High Doublewal," May 1983; Report to Doublewal Corporation,
Newton Upper Falls, MA. Available from: Doublewal Corp., 59 East Main
St., Plainville, CT 06062.
Hilfiker Company. 1984. "Reinforced Soil Embankment." Available from:

Hilfiker Company, 3900 Broadway, Eureka, CA 95501.
International Society for Rock Mechanics, Commission on Standardization of

Laboratory and Field Tests. "Suggested Methods for Determining Shear
Strengths," Document No. 1, February 1974. Available from: Printing and
Publishing Office, National Academy of Sciences--National Research
Council, 2101 Constitution Ave., N.W., Washington, DC 20418.
McKittrick, D. P. "Reinforced Earth: Application of Theory and Research to

Practice," Proceedings, Symposium on Soil Reinforcing and Stabilizing
Technigues in Engineering Practice, Vol 2, October 1978, pp 1-44.
Available from: U. S. Army Engineer Waterways Experiment Station, P. O.
Neilson, M. R. Pullout Resistance of Welded Wire Mats Embedded in Soil, 1984,

M.S. Thesis, Department of Civil Engineering, University of Utah, Logan,
UT. Available from: U. S. Army Engineer Waterways Experiment Station,
P. O. Box 631, Vicksburg, MS 39180.
Netlon Limited. "Guidelines for the Design and Construction of Reinforced

Soil Retaining Walls Using Tensar Geogrids," 1982. Available from: The
Tensar Corp., 1210 Citizens Parkway, Morrow, GA 30260.
Netlon Limited. "Tensar Test Methods and Physical Properties of Tensar

Geogrids," 1984. Available from: The Tensar Corp., 1210 Citizens
Parkway, Morrow, GA 30260.
Peterson, L. M., and Anderson, L. R. "Pullout Resistance of Welded Wire Mesh

Embedded in Soil," 1980, Department of Civil Engineering, University of
Utah, Logan, UT. Available from: U. S. Army Engineer Waterways Experi-
ment Station, P. O. Box 631, Vicksburg, MS 39180.
Price, William A., et al. User's Guide: Computer Program for Design and
Analysis of Inverted-T Retaining Walls and Flood Walls (TWDA), Instruc-
tion Report K-80-6 and K-80-7, December 1980, U. S. Army Engineer Water-
ways Experiment Station, Vicksburg, MS. Available from: U. S. Army
Engineer Waterways Experiment Station, P. 0. Box 631, Vicksburg, MS.
39180.
Reinforced Earth Company. "Reinforced Earth Retaining Walls,"

Brochure 2.18b/RE, 1980. Available from: Reinforced Earth Company,
Rosslyn Center, 1700 North Moore St., Arlington, VA 22209.
B-2
EM 1110-2-2502
31 Mar 89
Selvage, Heber, Nelson and Associates, Inc. "Engineering Analysis of the

Gridcote System," April 1984. Available from: Hilfiker Co.,
3900 Broadway, Eureka, CA 95501.
VSL Corporation. "General Specification for Retaining Earth Walls," July

1984. Available from: VSL Corporation, 101 Albright Way, Los Gatos, CA
95030.
VSL Corporation. "Retained Earth, Field Erection Manual," March 1983. Avail-
able from: VSL Corporation, 101 Albright Way, Los Gatos, CA 95030.
VSL Corporation. "Retained Earth Walls, Design Procedure for Standard Walls,"
March 1984. Available from: VSL Corporation, 101 Albright Way,
Los Gatos, CA 95030.
Welti, C. "Soil-Concrete Interaction Tests of 12' Wide Doublewal," October

1982, Glastonbury, CT. Available from: Doublewal Corporation, 59 East
Main St., Plainville, CT 06062.
B-3
EM 1110-2-2502
29 Sep 89
APPENDIX C
NOTATION
Chapters 3, 4, and 5
Symbol Term
b Distance over which base is in compression
B Width of base of structure
B Effective width of base
c Cohesion on slip plane of wedge
c Developed cohesion on slip plane of wedge
c Variable used to compute critical slip plane angle
c Variable used to compute critical slip plane angle

c
™ Hydrodynamic factor
C Coefficient used to compute wind loads
d Depth of water at breaking wave occurrence
d Depth of tension crack in cohesive backfill
d Water depth
D Depth of material in front of wall to base of structural wedge
e Eccentricity of resultant at base of structural wedge
F Inertia force of wall
FS Factor of safety
F Magnification factor
h Wall height; height of fill against gravity wall or height of

fill against "structural wedge"
H Design wave height
C-l
EM 1110 -2-2502
29 Sep 89
Symbol Term
H Height of wave which breaks in water depth ci

b
H Horizontal force, acting to the right, applied to wedge
L
H Any horizontal force applied above the top or below the bottom
Li
of the left side adjacent wedge
H Horizontal force, acting to the left, applied to wedge

R
Any horizontal force applied above the top or below the bottom
Ri
of the right side adjacent wedge
H Average of highest one-third of all waves or depth of satura-

S
tion in wedge
H Average of highest 1 percent of all waves

l
i Number of wedge being analyzed
k. Horizontal acceleration in g's

3
h
k Vertical acceleration in g's
3
v
K Lateral earth pressure coefficient
K, Active earth pressure

r coefficient
A
K,„ Mononobe-Okabe active earth pressure coefficient
AE *
K. Horizontal earth pressure coefficient for the i layer
K At-rest earth pressure

r coefficient
o
K a At-rest earth pressure coefficient calculated by Danish Code
equation
K Passive earth pressure coefficient
K Mononobe-Okabe passive earth pressure coefficient
L Length along slip plane of wedge
L. Length along the slip plane of the i wedge
N' Resultant of forces normal to the assumed sliding plane
N ,N ,N Bearing capacity factors for strip load
C-2
EM 1110-2-2502
29 Sep 89
Symbol Term
p Hydrodynamic pressure at depth y below top surface of water
p' Pressure due to compaction at depth z
p' Effective horizontal pressure at depth z
p'. Vertical effective earth pressure at the top of the i layer
p Horizontal active earth pressure at depth z
p^ Horizontal passive earth pressure at depth z

PH
P Lateral (horizontal) force produced by wedge
P Total active force on a unit length of wall backfilled with a

cohesionless material; static component for a driving wedge
P Static and dynamic forces due to driving wedge

AE
P Horizontal component of active earth force
P Absolute value of total horizontal force from driving wedges
P Hydrodynamic force given by Westergaard's equation

E
P Effective horizontal earth force contributed by wedge or wedge
segment
(P. - P.) Summation of applied forces acting horizontally on i wedge

i-1 i
P Static component for a resisting wedge
P Static and dynamic forces due to resisting wedge

PE
P Horizontal component of passive earth force
P Absolute value of total horizontal force from resisting wedges
P Internal water force acting on the side of the wedge free body
P Static component of water force for partially saturated wedge
q' Foundation pressure at base of structural wedge
q Effective overburden pressure
Q Vertical component of ultimate bearing capacity
C-3
EM 1110-2-2502
29 Sep 89
Symbol Term
SMF Strength mobilization factor
T Force tangential to slip plane of wedge
T Earthquake period of vibration in seconds
T Shear force that will cause failure along slip plane

F
U Uplift force normal to slip plane of wedge
U, Uplift force exerted normal to slip plane of the i angle
V Vertical force applied to wedge
V. Any vertical force applied above the top of the i wedge
2V Summation of vertical forces for structural wedge
V Maximum value of V for which the equations for c, and c

max ,. , 12
are valid
W Total weight of material in wedge
W. Total weight of water, soil, rock, or concrete in the i wedge
x Location of resultant force from toe of structure
Y,„ Line of action of P,„

AE AE
Y„„ Line of action of P__
PE PE
z Depth from the top of the wall
t~ Vi
z. Vertical distance measured down from the top of the i layer
z Critical depth where pressure due to compaction equals p'
z Depth
r to water table
w
a Angle between slip plane of wedge and horizontal
a. Angle between slip plane of the i wedge and the horizontal
ß Angle between top of wedge and horizontal
Y Unit weight of material
8 Angle of wall friction
C-4
EM 1110-2-2502
29 Sep 89
Symbol Term
y Effective unit weight of material
y. Effective unit weight of the i layer
9 Angle of the wall face from horizontal or inclination of wall

with respect to vertical
<|) Angle of internal friction on slip plane of wedge
()>' Drained friction angle
<)>, Developed angle of internal friction on slip plane of wedge
a Stress normal to slip plane
a' Effective normal stress

n
T Applied shear stress on slip plane of wedge
Tf Shear strength of wedge material
v|/ Seismic inertia angle
Y , y Saturated unit weight of fill
y Unit weight of water
y Buoyant unit weight of fill
tan <|> Unfactored shear strength parameter of the foundation material

through which sliding plane passes
tan <)) Portion of shear strength considered to be mobilized or devel-

oped along the slip plane(s)
tan c Unfactored shear strength parameter of the foundation material

through which sliding plane passes
^ Correction factors for bearing capacity
Ap Increase in horizontal pressure at distance x due to surcharge

HX
Ap Increase in horizontal pressure at depth z due to surcharge
HZ
AP Increase in horizontal force due to surcharge
H
AP Dynamic component of total driving force
AP Dynamic component of total resisting force

PE
C-5
EM 1110-2-2502
29 Sep 89
APPENDIX D
NOTATION
Chapter 9
Symbol Term
a Depth of equivalent rectangular stress block
A Gross area of section, sq. in.

g
A Area of tension reinforcement, sq. in.
s ^
A' Area of compression reinforcement, sq. in.
b Width of compression face of member, in.
c Distance from extreme compression fiber to neutral axis, in.
d Distance from extreme compression fiber to centroid of tension

reinforcement, in.
d' Distance from extreme compression fiber to centroid of compression

reinforcement, in.
D Dead load of the concrete members only or related internal forces

and moments
e' Eccentricity of axial load measured from the centroid of the

tension reinforcement = d - h/2
E Modulus of elasticity of reinforcement, psi
f' Specified compressive strength of concrete, psi
f Calculated stress at centroid of tension reinforcement when

s
compression controls
f Calculated stress at centroid of compression reinforcement
f Specified yield strength of reinforcement, psi
h Total depth of section, in.
k Ratio of stress block depth (a) to the effective depth (d), at

balanced strain conditions for hydraulic structures
k Ratio of stress block depth (a) to the effective depth (d)
D-l
EM 1110-2-2502
29 Sep 89
Symbol Term
L Live loads or related internal moments and forces
M Internal moment due to factored axial load, P

u u
P Axial load at given eccentricity at the balanced strain condition
P Nominal axial load strength at given eccentricity
P Factored axial load at given eccentricity

u
U Required strength to resist factored loads or related internal
moments and forces
V Shear strength
W Wind load or related internal moments and forces
ß A coefficient which accounts for the difference between the dis

m tribution of actual compression stresses and the assumed rectangu-
lar distribution of stresses
ß
K Defined the same as ßr but the value is in accordance with
l m
ACI 318
e Maximum usable strain at extreme concrete compression fiber = 0.003

c
e Design strain at the extreme concrete compression fiber = 0.5 e c
m
e Strain at the centroid of the tension reinforcements < f /E s
y y
<(» Strength reduction factor
p Ratio of tension reinforcement, A /bd
p Reinforcement ratio producing balanced strain conditions
p Reinforcement ratio corresponding to balanced strain conditions for

m
hydraulic structures
X Maximum percentage of p allowed for hydraulic structures
D-2
EM 1110-2-2502
29 Sep 89
APPENDIX E
COMPARISON OF DANISH CODE AND JAKY EQUATIONS FOR AT-REST

COEFFICIENT WITH COULOMB COEFFICIENT FOUND USING
REDUCED SHEAR STRENGTH PARAMETER $,
1
- tan (f «. *)
Jaky, Equation 3-4 Danish Code, Equation 3-6 Coulomb, Equation 3-14
Table E-l
U-lut Earth Freeaura Coefflclanta for Coaparlaon of Couloab'a Equation with an ShT of 2/3
to tha Danlah Coda and Jaky EquaMona
Inclined Backfill
Horizontal Backfill 8 - -to» « - 0' 8 - 10" 8 - 20"
4 ( K
o
It
0 06 o o8K K
o "oB
K
o *oB• K
o
(SHF - 2/3 (Oanlah) (SMF - 2/3) (Danlah) (SHF - 2/1) (Oanlah) (SMF - 7/3)
(det) (r«d) (Jaky) (SMT - 2/3) (Danlah)
10 0.175 0.826 0.791 0.683 0.703 0.826 0.791 0.970

it 0.192 0.809 0.772 0.669 0.686 0.809 0.772 0.950
12 0.209 0.792 0i754 0.655 0.669 0.792 ".754 0.930
13 0.227 0.775 0.736 0.640 0.653 0.775 0.736 0.910
1« 0.244 0.738 0.718 0.626 0.638 0.756 0.718 0.890
IS 0.262 0.741 0.701 0.612 0.622 0.741 0.701 0.870 0.931
It 0.279 0.724 0.684 0.599 0.607 0.724 0.684 0.850 0.871
17 0.297 0.708 0.667 0.585 0.593 0.708 0.667 0.831 0.833
18 0.314 0.691 0.651 0.571 0.378 0.691 0.651 0.811 0.802
19 0.332 0.674 0.634 0.557 0.564 0.674 0.634 0.792 0.774
0.349 0.658 0.618 0.544 0.550 0.658 0.618 0.772 0.748 0.883
20
21 0.367 0.642 0.603 0.530 0.537 0.642 0.603 0.753 0.724 0.861
22 0.384 0.625 0.587 0.517 0.523 0.625 0.587 11.734 0.707 0.839
0.401 0.609 0.572 0.503 0.510 0.609 0.572 0.715 0.680 0.818
23
2« 0.419 0.593 0.557 0.490 11.497 0.593 (1.557 0.696 0.659 0.796
0.436 0.577 0.542 0.477 0.485 0.577 0.542 0.678 0.638 0.775
25
0.454 0.562 0.528 0.464 0.472 0.562 0.528 0.659 0.619 0.754
26
27 0.471 0.546 0.513 0.451 0.460 0.546 0.513 0.641 0.599 0.733
0.581 0.712
za 0.489 0.531 0.499 0.438 0.448 0.531 (1.499 0.623
0.563 0.691 0.809
29 0.506 0.515 0.485 0.476 0.436 0.515 0.485 0.605-
0.471 0.413 0.474 0.500 0.471 0.587 0.545 0.671 0.747
30 0.524 0.500
0.458 0.401 0.417 0.485 0.458 (1.569 0.527 0.651 0.616
31 0.541 0.485
0.470 (1.1KH 0.400 11.47(1 0.445 (I.V./ (i.'.((> (l.hll tl. (>(■()
12 <l.55"> 0.445
0.376 0.389 0.455 (1.431 0.534 0.494 0.611 0.627
33 0.576 0.455 0.431
0.418 0.364 0.378 0.441 0.418 0.517 0.478 0.597 0.598
3« 0.593 0.441
0.405 0.352 0.367 0.426 0.405 0.500 0.467 (1.57V 0.577
35 0.611 0.426
0.341 0.356 0.412 (1.191 0.484 0.446 0.553 0.547
36 0.628 0.412 0.393
0.398 0.380 0.129 0.345 0.398 0.380 0.467 0.431 0.534 0.571
37 0.646
0.384 0.368 0.318 0.334 0.384 0.368 0.451 0.416 0.516 0.501
3« 0.663
0.371 0.356 0.306 0.323 0.371 0.156 0.435 0.401 0.497 0.479
39 0.681
0.357 0.344 0.295 0.313 0.357 0.344 0.419 0.386 0.479 0.459
40 0.698
0.344 0.332 0.384 0.303 0.344 0.332 0.404 0.372 0.462 0.439
41 0.716
0.320 0.273 0.292 0.331 0.370 0.188 (1.158 0.444 0.470
42 0.733 0.331
0.750 0.318 0.309 0.263 0.282 0.318 0.109 0.171 0.345 0.477 0.402
43
0.298 0.252 0.272 0.305 (1.298 0.158 0.131 0.410 0.384
44 0.768 0.305
0.286 0.242 0.263 0.293 0.286 0.144 0.318 0.393 0.167
45 0.785 0.293
Not«: A blank entry In tht tabl* denote« where ft '
E-l
EM 1110-2-2502
29 Sep 89
APPENDIX F
DERIVATION OF GENERAL WEDGE EQUATION FOR SINGLE

WEDGE ANALYSIS (EQUATION 3-23)
F-l. Effective horizontal earth force. Given the following driving wedge, an
equation for PBl! , the effective horizontal earth force, will be derived.
Is.
*v*
Summing forces normal to the slip plane yields,
HT sin a + U + N' - V cos a - H sin a - P sin a - P sin a - W cos a = 0
Solving for N' yields,
N' - (-1^ + HR + PEE + Pw) sin a - Ü + (V + W) cos a [F-l]
According to the Mohr-Coulomb failure criterion,
T = N1 tan 4 + cL [F-2]
Inserting Equation F-l into Equation F-2 yields,
F-l
EM 1110-2-2502
29 Sep 89
T = [(-HL + HR + PFR + pw) sin a - U + (V + w) cos a ] tan $ + cL
Setting the summation of forces parallel to the slip plane equal to zero
yields
ILL cos a + V sin a + W sin a - H„ cos a - Pw cos a - P„ cos a - T = 0 [F-3]

R EE W
Solving for T from Equation F-3 and substituting this expression into
Equation F-2 yields,
(HT - H_ - P^ - Pr7) cos a + (V + W) sin a

Li R EE W
+ [ (HT - H_ - P__ - P..) sin a + U - (V + W) cos a] tan ty - cL = 0

L R EE W
Simplifying and solving for P yields,

EE
p - (v + W) (sln
° ~ C0S a tan ^ + 0 tan ()> - cL
EE (cos o + sin a tan <J>) cos a + sin a tan $ L HR W
P - (V + W) Cl - cot a tan <(>) tan a U tan <(> - cL

EE (1 + tan o tan <|>) (1 + tan o tan $) cos a
+ HL - HR - Pw [F-4]
F-2. Soil parameters. For a particular SMF , the corresponding factored

parameters § and c can be inserted into Equation F-4 to yield
soil
(1 - cot a tan d>,) tan a U tan d> _ - c^L

P = (V + W) +
EE (l + tan a tan 0 ) (1 + tan a tan ty ) cos a
L R W
F-3. Resisting wedge. The same procedure can be applied to a resisting wedge
to yield the following equation for P .
EE
F-2
EM 1110-2-2502
29 Sep 89
(1 + tan <|) cot a) tan a U tan <t>.

T - C
d • dL
P„„ = (W + V)
EE (1 - tan <j> tan a) cos a (1 - tan § tan a)
H + H P
" L R " W
If more than one driving or resisting wedge exists, the value of P will
equal the difference of the earth forces applied to the wedge.
F-3
EM 1110-2-2502
29 Sep 89
APPENDIX G
DERIVATION OF EQUATIONS FOR CRITICAL SLIP-PLANE

ANGLE (a) FOR DRIVING AND RESISTING WEDGES
G_1
- Derivation of Critical Slip-Plane Angle (a) for Driving Wedges for the
Static Condition. In the following paragraphs the equations for the critical
slip-plane angle (a) will be derived for the static case for a driving wedge.
a. Introduction. The wedge equation (Equation 3-23) with the uplift term
omitted is:
p _ (W + V) (1 - tan <)) cot a) tan a cL

EE
1 + tan $ tan a ~ cos a(l + tan <J> tan a) [G-l]
where
length of slip plane

cos a (tan a - tan ß)
w = Yhs
2 (tan a - tan ß)
as shown in the figure below.
W - WEIGHT OF SOIL IN WEDGE,

V > ANY SURFACE LOAD OTHER THAN
A UNIFORM SURCHARGE
G-l
EM 1110-2-2502
29 Sep 89
Inserting the terms for L and W into Equation G-l yields,

p _ v(n^ - d^) (l - tan 4> cot a ) tan a
EE
2 (tan a - tan ß) l + tan cj) tan a
c(h - d )
V(l - tan d) cot a) tan a c
1 + tan Y<b tan a 2 .,_ a. ,„ . . . „,.
cos a (tan a - tan ß) (1 + tan <j) tan a)
12 2
Using the trigonometric identity — = sec a = 1 + tan a and putting
cos a
all terms over a common denominator
P
EE i Y(h ~ dcrtan a"tan ^ + 2V
^tan a
" tan
^ ^tan a
" tan
z)
- 2c(h - dc)(l + tan o)J * 2 (tan a - tan ß)(l + tan $ tan a)J [G- 2]
The first derivative of P

with respect to a may now be taken, and set
EE
equal to zero. The resulting expression is solved for the critical value of
tan a . For simplification, the calculus is done in parts.
b. First Derivative of y Term. Grouping the terms from Equation G-2

that are associated with y yields,
ylh
v - ,A ~dc) tan ct - tan <$>
EEy 2 (tan a - tan ß)(l + tan c|> tan a)
2
EEy
y(h
-0 2
tan a - tan + m ^
n
[Q_3]
tan <|> tan a + (1 - tan d> tan ß) tan a - tan ß
The first derivative of Equation G-3 is
G-2
EM 1110-2-2502
29 Sep 89
ndm m dn
dp 1. _L_
EEY _ da da
da 2
n
The denominator may be neglected because it is the same for all terms in
Equation G-2.
d Y h2
\ 2 ( "dc)
-=—*- = a sec a , let —i—s = a
da 2
|S = ^2 tan ♦ tan a + (1 - tan $ tan ß)J sec o
ndm. I ™ >m ^j
^ - aftan $ tan2 a + (1 - tan $ tan ß) tan a - tan ßl sec a

"da
iniv«
dnn
r ? ?
^— - a 2 tan <(> tan a - (2 tan $ + 1 - tan <j> tan ß) tan o
2 12
+ tan $ tan ß - tan ((»(1 - tan <fr tan 6)1 sec a
2
ndm m dn
Y _ Y m
Y
1■*(» -dc)r
' I-tan § tan
2 a + 2 tan
2 $ tan a
da " da
2
+ tan $(1 - tan $ tan ß) - tan ßj sec a [G-4J
c. First Derivative of c Term. Grouping the terms from Equation G-2

that are associated with c yields,
(v, _ A ) l + tan* a . = ^c
EEC C c
tan <|> tan2 a + (1 - tan * tan ß) tan a - tan ß n
Let -c(h - d ) = a
c
G-3
EM 1110-2-2502
29 Sep 89
da
^c 2
■r— ■ a(2 tan o) sec a
da
-jp = 12 tan $ tan o + (1 - tan $ tan ß)J sec a
ndm
c [3 2
2 tan 4 tan a + 2(1 - tan $ tan ß) tan a
da
- 2 tan ß tan a J sec a
m an
m dn T 3 2
-jj— * a 12 tan $ tan a + (1 - tan $ tan ß) tan a + 2 tan <fr tan a
1 2
+ (1 - tan (ji tan ß)J sec a
ndm m dn
c c T 2
- —J— - -c(h - d ) 1(1 - tan $ tan ß) tan a
da
- 2 (tan <f> + tan ß) tan a - (1 •* tan $ tan ß)J sec a £G-5]
d. First Derivative of V Term. Grouping the terms from Equation G-2

that are associated with the V term yields,
•D
JTü^-r
_ V [tan2 a - (tan <|> + tan ß) tan a + tan <J> tan B] m
^
•EEV
tan 4> tan2 a + (1 - tan <|> tan ß) tan a - tan ß n
-^ = v[2 tan a - (tan $ tan ß) ] sec2 a

da
-^ = [2 tan d> tan a + (l - tan d> tan ß) ] sec2 a

da
G-4
EM 1110-2-2502
29 Sep 89
ndm /r -.
~doF = V
»r tan
* tan a +
(2
~ 3 ta
™ <t tan ß - tan <J>) tan a
- [3 tan ß + tan $ - tan $ tan ß (tan $ + tan ß)J tan a
+ tan ß (tan $ + tan $)/ sec a
m dn rr -j
-J^- - V<|2 tan f tan a + (1 - 3 tan <J> tan ß - 2 tan <f.)J tan a
+ I2 tan <f> tan ß - (1 - tan $ tan ß)J tan a
+ tan <|> tan ß(l - tan <|> tan ß)> sec a
ndm m dn p
-J~ - -Tjj- - V [Cl + tan $) tan a - 2 tan ß(l + tan <fr) tan a
+ tan ß(l + tan2 $)J sec2 o [G-6]
e. Summation of Terms. From Equations G-4, G-5, and G-6, set the sum of
fndmY _mTdn1 + (ndmc _ mcdn>| + (ndmv _ nydn^ equal to zer0/ and divide by
V da do J 1 da do J V da da J
2
sec a
G-5
EM 1110-2-2502
29 Sep 89
<(*2 - «0 tan $ - c(h - dc )(1 - tan $ tan B) + V(l + tan *) tan 2 a
<*' - «ft» tan i(>)

+ 2c(h - d ) (tan $ + tan B)
c
- 2V tan B(l + tan $) tan a
<*2 - <2)
+ < —5 5—~ ftan ^ " tan
* tan
^ ~ tan
^
+ c(h - d )(1 - tan <(> tan B) + V tan2 B(l + tan <ji) > =■ 0
Divide all terms by Y(h> - d|)
2V(1 + tan f
tan * + 2C(1
"*"
Y(h + d*c)'"
ß)
tan 2 a
2
o2 *-tan
a„ * a.
A + 4c(tan <fr++ tan g) 4V tan B(l + tan $)
tan a
c 2 2
«* - < )
,,. _ . ^ 0. _ . , 2c(l - tan A tan P)

tan ?(1 - tan <fr tan 6) - tan B + — ,, . I . —
Y(h + dc)
2V tan2 ß(l + tan2 j>)

= 0 [G-7]
2 2
<" - < )
In Equation G-7, let the coefficient of tan a equal A , let the coeffi-
cient of tan a equal -Ac , and let the third coefficient equal -Ac .
Equation G-7 yields
G-6
EM 1110-2-2502
2 9 Sep 89
2
A tan a - Ac, tan a - Ac„ = 0
1 2
2
tan a - c tan a - c = 0
1 2
and
c, + Jcl + 4c.
tan oorit. = -^ Li 1
or
-l [ ci+ v°? + 4c
°crit. ■ tan
* \~ V "/ [G-8]
The coefficients c„ and c are defined as

1 2
9 4c (tan 4 + tan 8) 4V tan B(l + tan 4J

2 tan ^ A + _i /
* ■
c
l
Y(h^T7
c
Ä
E3T
* ^ fG 91
"
~/'8? ♦ ?M
tan #(1 - tan * tan B) - tan ft + ^ n B)
+ 2V
'"V ,(1 + j"2 ♦> [G-10]
V yhr - arj
c,2 Ä
where
2c (1 - tan * tan ß) 2v(l + tan2 <M

A = tan *+ „„,.,. \ " ,v ' [G-ll]
Y(h +
V
¥^)
Y(h^ - d-
G-7
EM 1110-2-2502
29 Sep 89
G-2. Derivation of Equation forV . The equations for calculating the

max
critical value of a are not valid when the value of V is too large. When
V is equal to or greater
3 than a certain maximum value (V ) the value of a
^ max
should be set in accordance with Figure 3-15. The value of Vmax is found by
setting Equation 3-28 equal to zero and•, solving.
-, .
tan d> + 2c (l - tan» tan ß) _ 2Vmax (1+ tan2 ») = Q

2 2
V(H+dc) Y(h -dc )
2Vmax (1+ tan2 <|>) _ y(h + d0) tan $ + 2c (1 - tan $ tan ß)

Y(h2 - d|) Y(h - dc)
Y(h - d ) tan 9 + 2c(h - d )(1 - tan * tan ß)

V = -A Si -£ [G-12]
max
2(1 + tan 2
♦)
G-3. Equations for Critical Slip-Plane Angles for Resisting Wedges for the
Static Condition. The following equations, for resisting wedges, where
derived from Equation 3-33 in the same manner used for deriving the driving
wedge equations for the static condition.
2
. _,_ 2c(1 + tan y tan B) . 2V(1 + tan 9) TG-131
Lta 1JJ
A - tan 9 + -r
Ytl
+ 5
Yti
2
2 «i,. +. 4c (tan 9 - tan ß) 4V tan 3(1
—+ tan 9)
2 tan
c
C
j ^ [G-W]
l A
2c(l + tan » tan ß) 2V tan2 ß (1 + tan »)

tan *(1 + tan <fr tan 6) + tan ß + ^5 7 2 [G-15]
G-8
EM 1110-2-2502
29 Sep 89
a = tan
-1 yR + 4c [G-16]
Note: in cohesive soil on resisting side of walls.
G-4. Effect of Water on Critical Slip-Plane Angle. The unit weight of soil
(y) to use in equations for calculating the slip-plane angle should be the
average unit weight of soil in the wedge. The average unit weight is deter-
mined by using the moist unit weight of soil above the water table and the
buoyant unit weight below the water table. The effect of seepage should be
taken into account in determining the buoyant unit weight. See Appendices M
and N for example calculations.
G-5. Derivation of Equations for Critical Slip-Plane Angle (a) for Driving
Wedges for Earthquake Condition. The equations for the critical slip-plane
angle (a) for a driving wedge as shown in the figure below for the dynamic
case will be derived.
h - c/e
a. Summation of Forces. Summing forces normal to the sliding plane

yields
G-9
EM 1110-2-2502
29 Sep 89
N = W cos a + P„„ sin a - k,W sin a

AE h
The shearing force T is defined by the Mohr-Coulomb failure criterion as
T = N tan <|> + cL = (W cos a + P sin a - k W sin a) tan <j> + cL
Summing forces parallel to slip plane and inserting the expression for T
yields
P„„ cos a - k, W cos a - W sin a + (W cos a + P,„ sin a - k, W sin a) tan <|>
AE h AE h
+ cL = 0
P„(cos a + tan 4 sin a) = W(sin a - tan <t> cos a)

AE
+ k,_W(cos a + tan d> sin a) - cL

n
Solving for P yields
W[(l + k tan <])) sin a - (tan <|> - k ) cos a] - cL

p _ —
AE cos a + tan d> sin a
Referring to the figure,
w _ y(^ - dl) L _ h - de
2 (tan a - tan ß) ' cos a (tan a - tan ß)
Inserting the terms for W and L into the equation for P yields
yfo* -d|) [(l + kh tan <t>) sin a - (tan a - kh) cos a]

^ 2 (tan a - tan ß) (cos a + tan <J> sin a)
c(h - d )
c_
cos a (tan a - tan ß) (cos a + tan (j) sin a)
G-10
EM 1110-2-2502
29 Sep 89
Using the trigonometric relationship sec a

2
cos a
a
y(h -dg) [(l + kh tan <(>) tan a - (tan j> - kh) ]
2 (tan a - tan ß) (l + tan $ tan a)
2c(h - dc) sec a

2 (tan a - tan ß) (1 + tan <|> tan a)
2 2
Now using the trigonometric relationship sec a = 1 + tan a and rearranging
(l + kh tan 4> ) tan o - (tan <|> - kh) , 2c, (1 + tan* a)

2P* h + dc m
2 2
y((h - d|) tan 4> tan a + (1 - tan <J> tan ß) tan a - tan ß
b. First Derivative of P „„ with Respect to a . The first derivative

AE _
of P with respect to a may now be taken, and set equal to zero. The
resulting expression is solved for the critical value of a . The first
derivative is equal to
2 P.
n-^ü -m dn
Y(h> - d,f) da da
da
/n _dni _ dn'
For this derivative to be equal to zero it is only necessary for l <ja â
to be equal to zero. In order to simplify operations let:
1 + k tan (() = a , tan <j> - k = b , and 1 - tan (|> tan ß = d
G-ll
EM 1110-2-2502
29 Sep 89
Then:
m - a tan a - b
- (h l\) (1 + tan a)
n - tan $ tan o + d tan a - tan ß
dm 2
da - (h iv) tan a sec a
§2
dot
- (2 tan $ tan a + d) sec a
dm 2 4c 3
a tan $ tan a + ad tan a - a tan B - u ^■ .■i tan $ tan a
da
4c 2
d tan2 a + .,,._ . , x tan ß tan a sec a
Y(h + dc) Y(h + dc)
2 4c
m dn
da
2 a tan $ tan a - 2b tan a tan a - "K^^"mg K tan $ tan a
c
Y(h
4
+ dc) tan
♦ tan3
« + ad tan a - bd - ^ ^ d
d tan2 a sec 2 a
Türhr
c
G-12
EM 1110-2-2502
29 Sep 89
dn dm
m -5da n -r-
do ,. 2c+, d, )N
-a tan <4T — Y(h tan 2
fc a
2
sec a
+ 2b tan <(> + „ 4c+ d . (tan ß + tan 0 tan a
-a tan ß + bd + Y(h 2c+ d ) = 0

c
Substitute 1 + k. tan <|> for a , tan <f> - k. for b and 1 - tan $ tan ß
for d
2c^ _tan 2 a
■(1 + k. tan <)>) tan $ - fh d > (1 - tan $ tan ß)
2(tan (fi - k.) tan (J> + ,. 4c^ . y (tan ß + tan <|>) tan a
-(1 + k, tan 0 tan ß + (tan $ - k.)(l - tan <{> tan ß)
2c
+ (1 tan tan e)
v(h + d ) ~ *
2 tan <(> (tan <fi - k.) + ,. 4c . . (tan if + tan ß)

2
tan a tan a
(1 + kh tan «) tan * + y(h^ d } (1 - tan «J» tan ß)
2c tan tan ß
tan 4» C1 — tan <|> tan ß) - (k. + tan ß) + Y/h + d ) Ü ~ * )
2c
(1+1^ tan <f>) tan * + >fa + d > (1 - tan <j> tan ß)
G-13
EM 1110-2-2502
29 Sep 89
then
: +
a = tan
-1 1 VC1 + 4c,
[G-17]
where
2 tan <|> (tan $ - t^) + J. + d . (tan $ + tan ß)

c, ■ [G-18]
1
(1 + k, tan <|>) tan $ + »2° d x (1 - tan 4 tan ß)
2c tan tan [G-19]

tan * (1 - tan <j> tan g) - (1^ + tan ß) + (h + d ) d ~ * &
2c - tan tan
(1 + k. tan (jj) tan * + (h + d ) d * &
[G-20]
*c 2
(sin a cos a - tan $ cos a)y
G-6. Equations for Critical Slip-Plane Angles for Resisting Wedges for
Earthquake Condition. The equations for the critical slip-plane angle (a) for
a resisting wedge are derived in the same manner used for the driving wedges.
The resulting equations are
o «■ tan
-1 "Cl +
VC1 + 4c,
[6-21]
/i j_ i ^ A ,. , . 2c(l + tan (j) tan ß) [G-22]

A - (1 + k. tan $) tan <f> + — -r—*
o/^ x i \ ^ x _i_ 4c(tan <}> - tan ß)

2(tan $ - k. ) tan $ + —5 z—r
[G-23]
tan ♦(! + tan * tan ß) + (tan ß - 1^) + 2c(l + tan + tan ß)

C = [6-24]
2
G-14
EM 1110-2-2502
29 Sep 89
G-7. Procedure for Finding the Critical Slip-Plane Angle, for a Wedge in a
Layer Below the Top Layer, of a Stratified Backfill. A layered soil system is
shown in the figure on the following page.
In order to find the critical slip-plane angle for layer 2, the weight of soil
in layer 1 will be considered a surcharge supported by layer 2. See figure
below.
G-15
EM 1110-2-2502
29 Sep 89
The weight of soil in parallelogram ABCD of the figure is a uniformly dis-

tributed surcharge that varies with a The uniformly distributed surcharge
does not affect the angle (X , but does have the effect of increasing the
unit weight of soil in wedge 2. The increased soil unit weight is calculated
as follows.
y' = increased unit weight
bu (tan ß. - tan ß.)

Y'hJ h1 +
tan <*„ - tan 3«
Y h
2 2
+ Y h
2 (tan <*2 - tan ß_) 2 (tan a - tan ß0) l 2 tan a - tan "ßT"
Y'h* 2Y h h +Y h Y.h, (tan ß. - tan ß.)

l l 2 2 2 , '1"2 1
2 (tan a - tan ß.) 2 (tan a - tan ß.)
(<
tan <*_ - tan ß
J
2Y h 2Y (tan ß - tan ß )
[G-25]
h„ '2tan <*„ - tan P„
The weight of soil in triangle ACE is considered to be a negative strip

surcharge that also varies with a . The value of this strip surcharge is
calculated as follows.
2
Y.,h
r n2 (tan ß. - tan »o>
-_
l 2
[6-26]
(tan <*2 - tan ß2)2
Using the terms y' and V , we have a wedge whose critical slip-plane angle
may be determined from Equations 3-25, 3-28, 3-29, and 3-30. See the figure
on the following page.
G-16
EM 1110-2-2502
29 Sep 89
Equations 3-25, 3-28, 3-29, and 3-30 become:
2c Jl + tan'2 <(._) 2Va(^tan2»2)

A tan +
' " *2 "Sh [G-27]
2 4c2(tan <f>2 + tan &2) 4Va tan BJl + tan2 $A

2 tan * +
*2 ?Tü ~Tz
c ^2
i = A^ — [G-28]
?A- + «an ♦,)

2c CI tan tan 6 zv tan 2
tan *♦,(!
»„.. ,. - »tan J.♦ l tan „8,)
2
, - tan 6, + —-
2 " _i*2 ?>
?_ + _2„ B,(l Jd [G-29]
2
Y'h, ,t22
v,
~
C +
o. = tan
-1 [ i Vci2 + 4c
2 [G-30]
Note that d (depth of crack in cohesive soil) is taken as zero in the above
equations. This is based upon the assumption that horizontal compressive
pressure, due to surcharge, is greater than any negative pressure that might
develop due to cohesion.
a. Procedure:
(1) Choose a trial value for ra .
G-17
EM 1110-2-2502
29 Sep 89
(2) Using trial value of a , calculate y' (Equation G-10) and

(Equation G-ll) V .
(3) Using the values of y' and V from step 2, calculate a from
Equations G-12, G-13, G-14, and G-15.
(4) If a from step 3 is equal to ain step 1 go to step 6. If a

2 2 ^
from step 3 is not equal to a in step 1 go to step 5.
(5) Use a from step 3 as a new trial value in step 1, and repeat
procedure.
(6) Stop, a from step 3 is critical value.
b. Example: Find a critical to nearest 0.5 degree.
y2 = 0.130 KCF
*2 = 20°
C2 = 0.8 KCF
From Equation G-10,
= 2(0.12) (12) 2(0.12) (0.4 - 0.1)

1
10 ' tan ra - 0.1
2
0.072
y' = 0.418 +
tan a - 0.1
2
G-1E
EM 1110-2-2502
29 Sep 89
From Equation G-ll,
0.12(10)2(0.4 - 0.1) 1.80

2 \j:an a - 0. y \tan a - 0. y
2
(1) a for long term loading (<|) = 20° , c = 0)
(a) First trial: a = 45° , y = 0.4980 , V = -2.2222

2 ' a
Using Equations G-12, G-13, G-14, and G-15,
A' = 0.36398 - 2(-2.2222)

S
<■■<■<■<■<■! '(1.132474)
1
'"" *' = 0.465038
0.4980(10)
0.264948 - 4(-2.2222) (0.1) (1.132474)
c
0.4980(10)
,'1 = n ^r»!o
0.465038 = 0.613200
2(-2.2222)iJ(0.01) (1.132474)
0.36397(1 - 0.36397 x 0.1) - 0.1 + —s ^
_ 0.4980(10)
C
2 ~ 0.465038
C' = 0.536971 , a = 47.75° 48°^ 45c
(b) Second trial: a = 48.0° , y' = 0.4892 , V = -1.7624
0.022649(-1.7624)
A' = 0.36397 - ^-^ ° ,,L0 2 L = 0.445566
0.4892
0.264948 .0.-004530 (-1.7684J

0.4892
C' = = 0.631260
1 0.445566
„ „„„„„., 0.0002265(-1.7624)u
0.250723 + , '
0n .4892
el2 = n ,,rrrr
0.445566 = 0.560875
G-19
EM 1110-2-2502
29 Sep 89
a = 48.45° 48.5° / 48°
(c) Third trial: a = 48.5° , y' = 0.4879 , V = 1.6957
0.022649(-1.6957)
A' = 0.36397 - n .!„' ' = 0.442687
0.4879
r, o^^.o 0.004530(-1.6957)u
0.264948 - '
c
0.4879
',
1 = n ..*rn„
0.442687 = 0.634064
„„„„„„ 0.0002265(-1.6957)L
n
0.250723 + ■—— -
C 0.4879
A2 = ,.n^n„
»0.442687 = 0.564588
a = 48.56° 48.5C
a = 48.5°
2
(2) a for short term loading (<b = 0 , c = 0.8 ksf)
(a) First trial: a = 45° , y = 0.4980 , V = -2.2222
A 2( 2 2222
' = nMo^L
498(10)
- " - l - 0.410530
°- 0.498(10)2
c' = 2 tan ß„ = 0.2

1 ^2
2(0.8) 2(-2.2222) (0.01)

0-498(10) 0,498(10)2
C
2 - OTH^ ^ = °-537936
01 = 40.04° = 40°
2
G-20
EM 1110-2-2502
29 Sep 89
(b) Second trial: a = 40° , y = 0.5154 , V = -3.2951
0.16 0.02(-3.7218)u „ „,„,„,

A' = - ' = 0.438304
0.5154 0.5154
„ , 0.16 0.0002(-3.2951)
-0.1 + +
„ „ , 0.5154 0.5154 „ .„„_„,
C' = 0.2 , c' = = 0.477203
1 ' 2 0.438304
a = 38.59° « 38.5° £ 40c
(c) Third trial: a = 38.5° , y = 0.5215 , V = -3.7218
0.16 - 0.02-3.7218 u „ ,,„,-,„

A' = „ _ ' = 0.449542
0.5215
„ „ 0.16 + 0.0002(-3.7218)
-0.1 + '
0 R?1 5
c' = 0.2 , ci = n ,"'* = 0.456865
1 2 0.449542
a = 38.07° « 38° ^ 38.5°
(d) Fourth trial: a = 38° , y' = 0.5237 , V = -3.8781
0.16 - 0.02-3.8781 „ „,--,^-,

A' = n ^ ' *- = 0.453622
0.5237
„ , 0.16 + 0.0002(-3.8781)
-0.1 +
0.5237
C' = 0.2 , c' = n „,-■,,■„„ = 0.449796
1 2 0.453622
CC„ = 37.89° 38c

2
(X„ = 38c
2
G-21
EM 1110-2-2502
29 Sep 89
(3) Check a = 48.5° (for long term loading) using Equation 3-23
w 0.13(10)2 0.12(12) (10) 0-12(10) (tan fi1 - tan ß2)

+ +
" 2 (tan a2 - 0.1) tan «2 - 0.1 2 ^ ^ . Q ±) 2
20.9 1.8
W
tan re-0.1 / „ \ 2
2 V tan a - 0.1^
W (tan a - tan A)
P = —
EE 1 + tan Y<b tan a
2 2
(X = 47.5°: W = 22.9149 kips
22.9149(1.091309
s - 0.36397) ,, „„„„ . .
P EE = 1 + 0.36397(1.091309)
= 11.9288 kips
xx.ôo ^^"
a = 48.5°: W = 21.9812 kips
21.9812 1.130294 - 0.36397 ,, „„,„ , . .. „„00 , .

p
™
EE = '1-, + 0.36397(1.130294)
r, -,^nni-, -.r.»™^ = 11-9348 kips > 11.9288 kips
a = 49.5°: W = 21.0869 kips
21.0869 1.170850 - 0.36397 u ,, „„„, . . .. n.AB

Pn„ = : 1 ^■,„„/., .,„„„,.„. = 11.9304 kips < 11.9348
EE 1 + 0.36397(1.170850) *
The critical a equals 48.5° which checks with the value computed in
paragraph G-7b(l)(c).
Check a = 38° (for short term loading) using Equation 3-23
G-22
EM 1110-2-2502
29 Sep 89
_ 20.9 LJ3 = 10
+
tana - 0.1 / . . \ 2' cos a (tan a - 0.1)
2 V tan a - 0.1 / 2 2
P = W tan a - cL/cos a
EE 2 2
a = 37°: W = 36.1931 kips , L = 19.1589 ft
0 8(19 1589)L
P„„ = 36.1931(0.753554) - '-la' = 8.0818 kips
EE 0.798636
a = 38°: W = 34.5554 kips , L = 18.6268 ft

2
PEE = 34.5554(0.781286) - "'p^ssO!!^ = 8.0875 kips > 0.0818
a = 39°: W = 33.0185 kips , L = 18.1289 ft

2
P = 33.0185(0.809784) - ° ' 11 ^H;^!^ = 8.0758 kips < 8.0875

EE 0.///146
The critical <x equals 38° which checks with the value computed in
paragraph G-7b(2)(d)
G-23
EM 1110-2-2502
2 9 Sep 89
APPENDIX H
DERIVATION OF PRESSURE COEFFICIENTS FOR SOLUTION OF LATERAL

EARTH PRESSURE PROBLEMS
H-l. Introduction.
a. Engineers are familiar with earth pressure coefficients and their use
in determining pressures and forces acting on retaining walls. The most
familiar and most often used are:
KA = tan*(450 - ™) , for driving pressure
Kp tan^/450 - -2] , for resisting pressure
The above represent special cases of Coulomb's equations for earth pressure
coefficients.
b. These simple coefficients are proper to use only when:
(1) Backfill surface is a level plane.
(2) Any surcharge applied to the surface is uniform, and covers the
entire surface of the backfill wedge.
c. The general equations from which these simple coefficients are ob-
tained are subject to the following limitations:
(1) Backfill must be cohesionless, unless the top surface is horizontal.
(2) Fill must be completely saturated or completely unsaturated, unless

the top surface is horizontal.
(3) Top can be a constant slope, but must be an unbroken plane.
(4) Any surcharge must be uniform and cover the entire surface of the
backfill wedge.
d. The correct lateral earth force due to any backfill wedge may be ob-
tained from the general wedge equation, and the general wedge equation is
subject to none of the above limitations. This equation may be used to solve
the most complicated problems of wedge geometry and surface loading.
e. If lateral earth pressure coefficients are derived from the general

wedge equation, these coefficients may be used in a rather simple manner to
H-l
EM 1110-2-2502
29 Sep 89
solve complex earth pressure problems. The general wedge equation will now be
derived and the pressure coefficients obtained from the derived equation.
H-2. Driving Side Earth Pressure.
a. A typical driving wedge is shown in the figure below.
W = WEIGHT OF SOIL IN WEDGE,

V = ANY SURFACE LOAD OTHER THAN
A UNIFORM SURCHARGE
In the derivation on the following pages it will be assumed that shear on the
vertical face of the wedge is zero.
H-2
EM 1110-2-2502
29 Sep 89
b. In the figure below, the forces acting on the wedge are shown along
with their components parallel and normal to the slip plane.
Setting the summation of forces parallel to the slip plane equal to zero:
P (cos a + tan <|> sin a) + (W + V) (tan <|> cos a - sin a) + cL = 0
Rearranging and solving for P
(W + V) (sin a - tan d> sin a) - cL

cos a + tan d> sin <x
From the previous figure:
h - d y(n2-d^ )
and W
cos a (tan a tan ß) 2 (tan a - tan ß)
H-3
EM 1110-2-2502
29 Sep 89
where
Y = unit weight of wedge material
c = cohesion
The equation for P will now be rewritten with the individual terms for W ,
V , and c separated.
p _ v(hx - dc) sin a - tan <|> cos a 1
2 ' cos a + tan <|> sin o ' tan a - tan ß
+ V (sin a - tan 4> cos a)

cos a + tan 4> sin a
c(h - dc)
cos a (tan a - tan ß) (cos a + tan <|> sin a)
This may be simplified and rewritten as:
n \ - ,A)
4* w, .. »,-...»,».
1 - tan T« cot a . tan a
1 + tan ♦ tan a tan o - tan 6
. V(l - tan ^ cot a) tan a

1 + tan * tan a
2c(h - d ) tan o
c [H-l]
2 sin a cos a(i""+ tan ♦ tan <»)(tan a - tan S)
c. Everything in the first term except y(h -d ) /2 is the lateral

earth coefficient for y and will be called K . Everything in the second
term except V is the lateral coefficient for the strip surcharge and will be
called K . Everything in the third term except 2c(h - d ) is the lateral
coefficient for cohesion and will be called K
c
11 - tan d) cot a \
d. Note that K and K both contain the term \~ T~ ~ / .
1 v 1 + tan q> tan a
H-4
EM 1110-2-2502
2 9 Sep 89
This is the lateral coefficient for y when the top surface is a level
unbroken plane. This term will be called K . Therefore:
tan
Kl = K ' «
tan a - tan ß
e. Note also that K and K both contain the term:

1 c
tan a
tan o - tan ß
This term which modifies K and K for the effect of surface slope. It
becomes unity when ß = 0 .
f. The equation for the total lateral force (P) produced by a driving
wedge can now be written, where the wedge material possesses both cohesion and
internal friction, where the top surface is a sloping plane, where the top
surface supports a strip surcharge, and where the wedge is either completely
saturated or completely unsaturated. The equation is:
V(h2 - dc) + K V - 2K c(h - d ) [H-2]

V c c
g. The individual forces and pressure distributions are shown in the

figure on the following page.
H-5
EM 1110-2-2502
29 Sep 89
NET STRESS DUE TQy&C

IS ZERO AT BOTTOM OF
CRACK.
* SEE RETAINING WALL

MANUAL FOR PRESSURE
DISTRIBUTION DUE TO
A STRIP SURCHARGE
COHESION SOIL WT.
h. The lateral coefficient (IC ) to apply to the effective weight of fill

(y ) below the saturation level in a partially saturated wedge will now be
determined. If the water table rises in a wedge that was previously unsatu-
rated, the lateral earth force will be reduced by the same amount on both
sides of the wedge. The slope of the earth pressure diagram, acting on the
vertical projection of the wedge slip plane, is Ky above the saturation
level and Ky below the saturation level. The slope of the earth pressure
diagram, acting on the vertical face of the wedge, is K y above the satura-
tion level and & Y below the saturation level. See the figure on the
following page.
H-6
EM 1110-2-2502
29 Sep 89
The force reduction on each side of the wedge (-P) is represented by the
shaded parts of the pressure diagrams.
K(Y - Yb)h^ (KlY - Vb)h;

, Kbyb = KlY - KY + KYb
(K K)
h - i - (^)+ K
( tan_a \ h\
I + Vtan a - tan ß
SmX / \Yfe I
i. Summarizing, the coefficients for driving wedges are:
K ■= ,1 +. tan
. r —
*T—tan a , basic value
\tan a - rtan öl
K,1 = KI- ß/ > apply
vv 3 to moist fill above saturation level
H-7
EM 1110-2-2502
29 Sep 89
Kb = K 1 + /__tan_a AA \1 apply to buoyant weight of fill

\tan a - tan ß ' \Yb/
below the saturation level.
K = K tan a , multiply times V to obtain lateral force due to strip

v
surcharge
v _ 1 tan g
, multiply times 2c
c 2 sin a cos a (1 + tan <(, tan a) tan a - tan ß
to obtain negative pressure due to cohesion.
j. A problem remains that must be solved before the coefficients can be

used for calculating driving pressures and forces, and that problem is the
value of the critical slip-plane angle. The critical angle is the angle which
produces the maximum driving force. The equations for calculating this angle
are derived in Appendix G and presented in Chapter 3 of the manual, and are as
follows:
a =
tan
■ l(clWCl+4c2J [3-25]
where
„ 4c, (tan $, + tan ß)

2 tan <fc, + ,, . , >
4V tan ß 1 + tan <|>

Equation 3-28
<"' - 0
2c,(1 - tan A, tan ß)
d i_a
c2 - tan <|>j(l - tan <(>, tan ß) - tan ß +
Y (h + d c)
2V tan2f6 1 + tan2 Â
7 f A Equation 3-29
V^
H-8
EM 1110-2-2502
29 Sep 89
and
2c.(1 - tan 4>, tan 3) 2VML + tan2 *dJ

A « tan 4> + [3-30]
a Y(h + dc)
FÎ
k. The effect of water is accounted for by using the average unit weight
of soil for Y in the above equations. The average unit weight is based on
the moist unit weight of soil above the water table and the buoyant unit
weight below the water table. The effect of seepage should be considered in
determining the buoyant weight.
H-3. Resisting Side Earth Pressure.
a. Pressure Coefficients. The pressure coefficients for the resisting

side are
tan a
K = 1 + tan <t> cot a K = K /
l - tan <j> tan a ' 1 \ tan a - tan ß
K„ = K tan o
Kb = K l +| tan_oc _ 1
\ tan a - tan ß Ybj.
tan a
K„ =
2 sin a cos a (l - tan 4> tan a) ' tan a - tan ß
The term for cohesion (2K c) is positive for resisting pressure calculations,
c
not negative as it was for driving pressure. Therefore, the crack of depth
d does not exist on the resisting side,
c
b. Critical Slip-Plane Angle. The equation for the critical slip-plane
angle for a resisting side wedge is
2X * yCl2 * 4c2
a = tan
2
H-9
EM 1110-2-2502
29 Sep 89
Values for c and c are determined from the equations in Appendix G.
c. With the above changes, the method for determining resisting pres-
sures and forces is the same as for the driving case.
H-10
EM 1110-2-2502
29 Sep 89
APPENDIX I
DERIVATION OF EQUATION FOR DEPTH OF CRACK d IN COHESIVE SOIL

c
1-1. Definition. By definition, the bottom of the crack will lie at the
depth where the net horizontal stress in the soil is zero.
Pv - K,vd - 2K c - 0 [1-1]
h 1' c c
where
„ _ l - tan <{> cot g tan a

1
l + tan 4> tan a ' tan a - tan ß
tan a
2 sin a cos a (1 + tan $ tan o) (tan a - tan ß)
The coefficients K
and K are derived in Appendix H. Rearranging
1 c
Equation 1-1 and solving for d yields:
2K c
d ==-£- tI-2]
c K^
Equation 1-2 is valid for a sloping soil layer.
1-2. Horizontal top surface. When the top surface is horizontal,
K, = KÄ(Coulomb)
and
1-1
EM 1110-2-2502
29 Sep 89
APPENDIX J
LATERAL PRESSURES DUE TO COMPACTION
J-l. Design pressure envelope. The design pressure envelope for nonyielding
walls with compaction effects will be derived. The lateral pressure due to
at-rest conditions is shown in Figure J-l.
EFFECTIVE PRESSURE, p'
\
Po = K0Y'z
-4^<-
Figure J-l. Lateral pressure due to at-rest conditions

(y = Y above water table).
The lateral pressure induced by a compaction roller line load is shown in

Figure J-2.
J-l
EM 1110-2-2502
29 Sep 89
■♦-EFFECTIVE PRESSURE, p'
"^ ^ PASSIVE PRESSURE = MAXIMUM SUSTAINABLE PRESSURE
Pp = V'z
Figure J-2. Lateral pressure induced by compaction roller line load.
In Figure J-2,
2P
7IZ where P is the roller load, lb/linear ft
2K0P
APv, = where P is the roller load, lb/linear ft
7TZ
The maximum lateral pressure occurs at z and the passive pressure is
P' = K Y'Z [J-l]

P P
Taking
*p
and inserting this into Equation J-l yields
rt _ Y'z
[J-2]
P KA
J-2
EM 1110-2-2502
29 Sep 89
The horizontal pressure due to the earth and roller is
2K P
o [J-3]
P' - K Y'z +
h o TTZ
Using Equations J-2 and J-3 and solving for the critical depth z yields
Y'zc 2K„P
K +
oY'Z,r uz„r
2 2 2KAK0P
Y'z*r = KAKoY'zcr + * °
Y'zc2r(l -KAK0) - --^5-
Assuming (1 - K K ) ~ 1
2KaK0P
N *Y'
The horizontal pressure at z is
Y'zc 2K0PY '

Ph =
The maximum pressure is constant below z until it is exceeded by at-rest

* cr
pressure, because the foregoing analysis represents each successive top lift.
The design pressure envelope for nonyielding walls including the effects of
compaction is shown in Figure J-3.
J-3
EM 1110-2-2502
29 Sep 89
-er
P = Kpr'z
P=
2K0py
KA7T
P'= Kor'z
cr -m KnP
r Z
2 =
2?
KAK07rr'
Figure J-3. Design pressure envelope for nonyielding walls
with compaction effects.
J-4
EM 1110-2-2502
29 Sep 89
APPENDIX K
DERIVATION OF VERTICAL SHEAR FORCE FOR UPWARD SLOPING BACKFILL
K-l. Derivation for Shear Required on Vertical Faces of Earth Wedges. When
the vertical face of an earth wedge does not lie on the same plane as the face
of the structural wedge, a shear force is required in order that the horizontal
earth force may be transferred between wedges.
A general situation where such a force is required is shown below in

Figure K-l.
FACE OF WEDGE 1
■ FACE OF STRUCT. WEDGE
SUP PLANE
WEDGE 2
Figure K-l. General condition where shear force is required
The earth force calculated for wedge 1, using the provisions of the text, is a
force acting on Surface AB. In order for the same force to act on Surface CD,
a shear force must exist on vertical planes in Block ABCD. A free body of
Block ABCD is shown in Figure K-2.
K-l
EM 1110-2-2502
29 Sep 89
a
A
V C
W ^
"äB ,
i. V
»
P
^ AB
'' Sj a
Q
a fan 02_»j B***""**— O
D
SHEAR ON INTERFACE
BD IS ASSUMED
TO BE ZERO
w
Figure K-2. Free body of Block ABCD.
Taking moments about D:
AB
AB +a ..tan „^ 1 - —
— J_ CD
- va = 0
where
h = h a (tan ß tan ß }
CD AB " l ~ 2
then
pJ^tatMt2.""ta,îtant' = va
a tan ß a tan ß ^
PAB la tan ß2 + 3 = va
K-2
EM 1110-2-2502
29 Sep 89
v = PflB( tan pt + 2 tan ß2 )
See example 6 in Appendix M and example 1 in Appendix N for applications of the

above equation.
K-3
EM 1110-2-2502
29 Sep 89
APPENDIX L
DERIVATION OF GENERAL WEDGE EQUATION FOR MULTIPLE WEDGE ANALYSIS
L-l. Free-body diagram. A free-body diagram of an i wedge is shown below
_HRi
-.ST
Pi £>
SLIP PLANE
Writing equilibrium equations normal and parallel to slip plane,
EF = 0 :
n
0 = N. + U. - W cos (-a.) - V. cos (-a.) + HT . sin (-a.) - H_. sin (-a.)

ii ii ILi i Ki i
+ P^j sin (-a±) - V sin (-c^)
Using the trigonometric relationships,
m
cos (-a.) cos a
L-l
EM 1110-2-2502
29 Sep 89
and
sin (-a) = -sin a
N (W + C0S (H
i" i V ^l* " Li " HRi) (_Sin
V " (P
i-l " V (_Sin
V " °i
EFt - 0 :
0 - -T + WjL sin (-a ) + V± sin (-o±) + HLi cos (-a±)
- IL cos (-a.) + P., cos (-o^) - ?± cos (-a/)
?i « (WjL + V±) (-sin ap + (H^ - H^) cos a± + (P±_j - Pj) cos o±
According to the Mohr-Coulomb failure criterion,
TF = N. tan *± + c^
Writing the equation for the sliding factor of safety,
TF Ht tan »± + c^
FS - _ - _
i i
where FS. = factor of safety.
Substituting the expressions for T. and N. into the equation for FS^^
yields
[(W± + Vt) cos aL + (B^ - HR1) sin a± + (P^ - P^ sin a± - pj tan 4>t + c1L1
FS
i " -(Wj + Vt) sin at + (^ - H,^) cos a.± +■ (P^ - P±) cos c^
L-2
EM 1110-2-2502
29 Sep 89
Solving for (P. , - P.),

l-l l
(f±_l ~ Pj) = [(W± + V±)(tan *di cos a + sin o±) - U± tan <J>di
+ (H
Li " HRi) X (tan
*di S±n
"i " COS
«i) + C
diLi]
* [cos ai - tan $ sin o ] [L-l]
Equation L-l is the general wedge equation.
L-3
EM 1110-2-2502
29 Sep 89
APPENDIX M
LATERAL EARTH PRESSURE COMPUTATIONS, EXAMPLES
SUMMARY OF EXAMPLES
Example 1, Page M-3 Example 4, Page M-ll
SURCHARGE
WITH COMPACTION ffl 0- 35

°_„
EFFECTS c ■ 0 ""*
Example 2, Page M-5 Example 5, Page M-21
CRACK
0-0
c - 0.60 KSF
M-l
EM 1110-2-2502
29 Sep 89

-SURCHARGE
xzzr
0= 35"
c » 0
3
&'':£ •w'l'i'w'VP
OB»
Example 9, Page M-52
r^sr
0= 35"
c = 0
1
TTO rsa ^§F^*»
M-2
EM 1110-2-2502
29 Sep 89
LATERAL EARTH PRESSURE COMPUTATIONS, EXAMPLES
M-l. EXAMPLE 1. Find the Lateral Earth Force and its pressure distribution
on Surface AB. Consider the effects of compaction in
accordance with paragraph 3-17.
P = Line load for compaction roller = 5 k/ft
STRUCTURAL WEDGE
/? = 0
BACKFILL:
y = 0.12 KCF
0 = 30°
C=0
T
v
B
a. Active and passive pressure coefficients.
SMF = 1.00 , 0 = <|> = 30°
KA = tan2 (45° - 4>d/2) = 1/3 [3-15]
Kp = tan2 (45° - <J>d/2) = 3 [3-20]
b. At-rest earth pressure coefficient.
SMF = 2/3 , <|> = tan" (2/3 tan <|>) = 21° (from paragraph 3-llc)
K0 = tan2 (45° - 4>d/2) =0.47
M-3
EM 1110-2-2502
29 Sep 89
c. Calculation of earth pressures. From Figure 3-30:
2W rrmfwnsY g2,Mft
N ity V 7t(0.12)
2P _ f ITS) = 13.01 ft
KftK07tY V 1/3(0.47)(n)(0.12)
2K0£YPY _= /2(0.47) (5)

(5)T(0.12) = 0.734 ksf
- hm
K; i« V (l/3)it
The force and pressure distribution are shown below:
s
A
V^
K_y^ ^
JfJMK I
•$
0.734
KSF-^
5
eg
H
ei
K
13.17 —f"
i,
1
0.734 "
■■
•KSF I
^
»"
ifr
Al
1.015 B
KSF
M-4
EM 1110-2-2502
29 Sep 89
M-2. EXAMPLE 2. Find the lateral earth force and pressure distribution
acting on Surface AB.
DRIVING STRUCTURAL
WEDGE WEDGE
Y = 0.120 KSF
<t> = 30°
c = 0
SMF = 2/3
0d = 21°
tan/5 = 0.25
a. Calculate a
c, = 2 tan 4>d = 2(0.383864) = 0.7677 28 [3-26]
1 - tan <|>d tan ß tan ß [3-27]

tan <J>d
=
1 - 0.383864(0.25) - 3Ö3L4 0.252762
c1 + <Jc% + 4c2 [3-25]

a = tan" = 45.466°
b. Lateral earth pressure coefficient (see Appendix H). From the equa-
tions contained in Appendix H:
M-5
EM 1110-2-2502
29 Sep 89
^ (l - tan 0dcot «\ . tm g .
1 " \ 1 + tan $, tan «J\tan a - tan (5/
383864 x 0.983864 K1.016400\ „ ,„,

1 \1 + 0. 383864 x 1.016400 0.766400) " °'5937
Alternatively K. may be calculated using Equation 3-14:
cos $,
1 +
[sin $. sin
cos f$
(**zA
ß - tan (0.25) - 14.0362° , 4>.a - B - 6.9638"
(0.933580)'
0.5937
[.♦JE^ 358368(0.121242)
970143
c. Lateral force and pressure distribution. The lateral force and pres-
sure distribution are shown in the figure below:
Ktf = 0.5937(0.12) = 0.07124
8
PEE= 14.25K/FT
11
B
1.4248
KSF
M-6
EM 1110-2-2502
29 Sep 89
M-3. EXAMPLE 3. Find lateral earth and water forces acting on Surface ABC.
Use earth pressure coefficients and check by iteration
of Equation 3-23.
rMOIST = 0.120 KCF

>W.= 0-125 KCF
>\VATER = 0.0625 KCF
y
BOUY. =?b
Yb = 0.0625 KCF
<D = 30°
C=0
SMF = 2/3
<Dd = 21°
a. Lateral earth pressure coefficients (see Appendix H). The critical

slip-plane angle a = 45.466° (from Example 2)
_ 1 - tan ,frd cot g ^ x . 0.383864(0.983864) _ . ,,_,,_

u
1 + tan <f>d tan a 1 + 0.383864(1.016400) -^'000
h - «L T- L..) - °-4"«8 (Ml) - ••»»

tan a
s-- K 1 + ( tan o - tan ß
■«
- 0.447668
L VO.7664 V\0.0625/J
- 0.7280
M-7
EM 1110-2-2502
29 Sep 89
b. Lateral forces and pressure distribution. The lateral forces and

pressure distribution are shown in the figure below:
,i
K, YM = 0.5937 (0.12) = 0.07124-
Kb ?b ~ 0.7280 (0.0625) = 0.0455 •
0.7302
13.32K/FT f PeE
s
0.625 1.1852 c
KSF KSF
WATER SOIL
c. Check soil force by iterating Equation 3-23,
W = total wedge weight, including water
2
Y h
m AC \ sat m/ s
W =
2 (tan a - tan 3) 2 tan a
0.12(20.25) ^ (0.005)(10y 24.604 + 0.25

W =
2 (tan a - tan 6) 2 tan a ~ tan a - tan ß tan a
Y
waterhs 0.0625(10)2 _ 3.125
U - uplitt " 2 sin a
=
2 sin a sin a
p =W^ = 0.0625(10)2 = 3125k/ft

W 2. 2
M-8
EM 1110-2-2502
29 Sep 89
W (tan a - tan <(>.)+ U tan <fc-/cos o

P = —^ 2Z 2 p
EE 1 + tan $, tan a w
Let a - 45.466°:
w
w
„ 24.604 0.25 m .
K/It
0.766400 1.016400 ^-^^
u =
ÖT7tÜ4 = 4 3839k/ft
-
P 32.3493(1.016400 - 0.383864) + 4.3839(0.383864)70.701332

EE * 1 + 0.383864(1.016400)
- 3.125 - 13.3203 k/ft
Let a = 44.466°:
w
- 05T55T + üÄr " 33 8883 k/ft
'
u =
Oöö§6 " 4'4612 k/ft
p 33.8883(0.981531 - 0.383864) + 4.4612(0.383864)70.713666

EE 1 + 0.383864(0.981531)
- 3.125 = 13.3290 k/ft > 13.3203 k/ft
Let a = 43.466°:
m 24.604 0.25 = .
0.697837 0.947837 ■"•"« K/rc
1 125
U = —->.■!.*-> s <t
A 3tf//
5427 k/ft
K rc
0.687924 - '
M-9
EM 1110-2-2502
29 Sep 89
35.5213(0.947837 -0.383864) + 4.5427(0.383864)/0.725783

1 + 0.383864(0.947837)
3.125 = 13.3254 k/ft < 13.3290 k/ft
a critical = 44.466° instead of 45.466°.

P = P„„ = 13.33 k/ft instead of 13.32 k/ft
max EE
Conclusion. These small differences in a and Pare due to the

EE
fact that the effect of water on the critical slip-plane angle is neglected in
Equations 3-26 and 3-27. These differences are well within the permissible
range of error required for soil pressure calculations. It can be concluded
that for a cohensionless soil without a finite surcharge (V), it is not neces-
sary to consider the effect of water when calculating the value of a .
M-10
EM 1110-2-2502
29 Sep 89
M-4. EXAMPLE 4. Find lateral soil force (P ) that will act on Surface ABC.
EE
Show the effect of water on slip-plane angle (a), and earth
force.
_ DRIVING WEDGE _ STRUCTURAL WEDGE

h
tan a - tan ß
VGKIFT—+-
i 2
'
2' 2'
L 9'
\ ^ "*- L T t i •
A
8 >
\ \ csi
\_i_ B "V *" 1
\ \
v*'
\ \ V*.' 8
Is
Yu = 0.120 KCF \\ II
sII
ys = 0.125 KCF •c
YB = 0.0625 KCF \\
<D=35° ;•■;«:
C =0 ^
74JSnv/V\\
SMF = 2/3 a "<f-•a"*'.'•-,'••■.'.*.,• •• a
<J»d = 25° ****** ■rtft
1 1
a. Calculate cc--neglecting effect of water. From Equation 3-30

(omitting the c term)
A - tan «Dd - 2V(1 + tan- Qd) _ Q M3QB _ 2(6) (1.217443)

Ymh< 0.12(20.25)2
A = 0.169416
From Equation 3-28 (omitting the c term)
M-ll
EM 1110-2-2502
29 Sep 89
2
, 4V tan e(l + tan2 A.)
2 tan * i—5 *Z
*mh
-1 " A
2
2(0.466308) - M6)(1M)(1.217443)
0.12(20.25)*
0.169416
cx - 1.690751
From Equation 3-29 (omitting the c term)
2V tan2 en. + tan2 *dj

tan 4,(1 - tan $. tan ß) - tan ß + s '
d a
Y h
'm
"2 ' A
0.*66308[<1 - 0.466308(1/«)] - i + «W<l/W<»-»™»

0.12(20.25)' 1.065442
0.169416
a - tan -i (vu/jEi^. a. 354« [3-25]
b. Calculate a—include effect of water. Use y avg instead of y m,

where:
avg
V>
2 (tan o - tan ß)
{\ - Yb)h8
2 tan a [■2 (tan a - tan J
Let a - 74.5778"
M-12
EM 1110-2-2502
2 9 Sep 89
_ [o. 12(20.25)2 0.0575(16)2] . I" (20.25)2 1

T
avg L2(3.374990) " 2(3.624990)J T [2(3.374990)J
Y avg - 0.087 kef
A = 0.466308 - 2^(1'217A43> - 0.056802

0.087(20.25)Z
2(0.466308)2 - *(6)(1/»)(1.217443)
c 0.087(20.25)2 =
1 0.056802 «.im«/
0.466308[l - 0.466308(1/4)1 - I + 2(6) d/16)(1.217443)

c * 0.087(20.25)^
2 0.056802
c2 - 3.301668
^lîiJÄL
a - tan~M — V1
4c
- / = 78.104° > 74.5778°
Use: a » 74.5778° , the entire surcharge will not lie on the top surface of
the wedge when the angle is greater.
c. Calculate earth pressure coefficients (see Appendix H). For

a = 65.354° (neglecting effect of water):
1 + tan <J>, cot a

K -- -*
1 - tan <}>, tan o
m 1 - 0.466308(0.458807) _
K
1 + 0.466308(2.179565) °-389841
tan a
IT = y( \
1 Vtan a - tan ß/
M-13
EM 1110-2-2502
29 Sep 89
K
i ' 0'38984l(f$fÜf) ■ °'AA0»
K 1 + / tan « \/\
«b- Vtan a - tan B " J\y
Y^ - 0.389841 1 + (2.179565 ,V0.120 >

U. 929565 7\0.0625>
,48682
KV - K tan a
Ky - 0.389841(2.179565) - 0.84968
For a - 74.5778° (including effect of water):
K - 1 " 0.466308(0.275863) _ ftU „,JBBJ

ftR,
* 1 + 0.466308(3.624990) '^
Ki " °-323883(oftll§) - °'34787
K, - 0.323883[l + (Itfllllg - l)(g^f§5)] - 0.36995
K - 0.323883(3.624990) - 1.17407
d. Calculate lateral soil force (using coefficients). For a - 65.354°:
P (1/2)
Y - Vm(h " hs)2 +
<1/2><hs>[2KlVh " V +
Vbhs]
*y - (1/2)(0.44035)(0.12)(4.25)2 + (1/2)(16) [2(0.44035)(0.12)(4.25)
+ 0.48682(0.0625)(16)1
Py - 7.965 k/ft
M-14
EM 1110-2-2502
29 Sep 89
P « K V - 0.84968(6) - 5.098 k/ft
PEE - 7.965 + 5.098 - 13.063 k/ft
For a - 74.5778°:
P - (1/2)(0.34787)(0.12)(4.25)2 + (1/2)(16)[2(0.34787)(0.12)(4.25)
+ 0.36995(0.0625)(16)
P - 6.175 k/ft
Y
P = 1.17407(6) - 7.044 k/ft

v
PEE - 6.175 + 7.044 - 13.219 k/ft
e. Find lateral soil force by iteration of Equation 3-23. Simplifying

Equation 3-23.
(W + V) (tan a - tan A.) + U tan 4./cos a

P 2 £ p
EE 1 + tan 4, tan o w
„
w
**m , vs, Gs - 0*
Y
m/ s
2 (tan o - tan ß) 2 tan a
V - 0.12(20.25)2 + (0.005)(16)2 = 24.6038 + 0.64

2 (tan o - tan $) 2 tan ot tan a - tan ß tan a
Y
h2 9
U = w s m 0.0625(16)z m 8
2 sin a 2 sin a sin a
M-15
EM 1110-2-2502
29 Sep 89
6 (16)2
Pw - ^z - °-° "l - 8.000 k/ft
Let a - 73.5778'
.. _ 24.6038 0.64 „«,-,, , /*..

W + = 8 0171 k/ft
" 3.142854 3.392854 '
= 8 3402 k ft
Ü = 0>959205 - / • W + V - 14.0171 k/ft
P 14.0171(3.392854 - 0.466308) + 8.3402(0.466308)/0.282713

=
EE 1 + 0.466308(3.392854)
- 8.000 - 13.214 k/ft
Let a = 74.5778°
TT 24.6038 , 0.64 _ .,,, , ..

W =
3.374990 + 3.624990 = 7 4666 k/ft
'
W + V = 13.4666 k/ft , U = 0 g*3g92 - 8.2988 k/ft
_ 13.4666(3.624990 - 0.466308) + 8.2988(0.466308)/0.265930

EE ~ 1 + 0.466308(3.624990)
- 8.000 - 13.220 k/ft > 13.214
Let a ■ 75.5778° (all of V does not lie on top of wedge)
h 20.25
3O0:>:>
tan a - tan ß " 3.638487 " "
v . ^5.5655 - 2\ 6 k/ft = 5 34g3 k/ft
M-16
EM 1110-2-2502
29 Sep 89
24.6038 , 0.64 . .,., ./f

W =
3.638487 + 3.888487 " ••Wb/ *'"
W + V - 12.2750 k/ft , Ü = 8/0.96847 - 8.2603
12.275(3.888487 - 0.466308) + 8.2603(0.466308)/0.249065

EE "■ 1 + 0.466308(3.888487)
- 8.000 = 12.429 k/ft < 13.220
P = 13.220 k/ft (agrees with coefficient solution where o

±s found considering the effect of water)
f. Determine line of action for lateral force due to V using the

approximate method of Figure 3-29. Find a' , the slip-plane angle without
surcharge:
Use SMF = 1.00 in Equations 3-26 and 3-27.
Cj ■ 2 tan ♦ ■ 2(0.700208) - 1.400416
, a tan ß
c- = 1 - tan <p tan P - T
2 tan <p
c2 - 1 - 0.700208(1/4) - flfigigj - 0.467911
From Equation 3-25
...«„-•(fjjj/pS).,,.*
M-17
EM 1110-2-2502
29 Sep 89
The location of P is determined in the following figure.
Pressure distribution and line of action of earth force P for

EE
a 65.354°. The pressure distribution and line of action of earth force P.
EE
for cc = 65.354° is shown on the following page. A pressure distribution must
be assumed for the lateral force due to V since only the location of the
resultant force is known. The pressure distribution will be defined by an
isosceles triangle with the apex located at the point of application of the
resultant force due to V . See example 10 of this appendix for the computa-
tion of the lateral force due to a surcharge by the elastic method.
M-18
EM 1110-2-2502
29 Sep 89
0.7114 0.7114
KSF KSF
H. PEE
(Py + Pr)
Pressure distribution and line of action of earth force P. for

EE
a = 74.5778°. The pressure distribution and line of action of earth force
for a = 74.5778° is shown on the following page:
'EE
M-19
EM 1110-2-2502
29 Sep 89
(Py + K)
i. Conclusion. For a cohensionless soil when calculating a from Equa-

tions 3-28, 3-29 and 3-30, the unit weight of soil (y) in the strip surcharge
(V) term should be the average effective unit weight (y ) y_ should be
avg
calculated using the moist unit weight above the water table and the buoyant
unit weight below the water table.
M-20
EM 1110-2-2502
29 Sep 89
M-5. EXAMPLE 5. Find lateral earth force acting on Surface ABC. Use moist
unit weight of soil to calculate a . Check solution by-
iteration of Equation 3-23.
yMOIST = 0-120 KCF

rSAT, = 0.125 KCF
YBOUY. = 00625 KCF
*=0
c =0.60 KCF
SMF = 2/3
cd = 0.40 KSF
tanj8 = 1/4
a. Calculate slip-plane angle a. Estimate a = 40c
Using Equation 1-2 with $ = 0 yields
C f
d \ 0.4/0.12
6.77 ft (Appendix I)
c sin o cos a 0.642788(0.766044)
From Equation 3-30
2c.
2(0.4)
0.269143
Tin
m(h + d ) 0.12(24.77)
c
From Equation 3-28
4c, tan ß
d
4(0.4)(l/4)
vj*
m + dc ) 0.12(24.77) ,
c U,:>U
l - 0.269143
M-21
EM 1110-2-2502
29 Sep 89
From Equation 3-29
2c
d 1 , 2(0.4)
—can p "T ■ h am+L-—»«r"
Tc d
C
V c>
4 0.12(24.77)
- 0.071125
2 " A 0.269143
From Equation 3-25
C +
. -l(V
a - tan l >/C^l + 4c
2l
/ - 31.61° * 40°
Let a - 31.61°:
0.4/0.12
c 0.524135(0.851635) - 7.47 ft
2(0.4)
0.12(25.47) 0.261746
4(0.4)(l/4)
_ 0.12(25.47)
C U,:>U
l 0.261746
2(0.4)
-iA +
,.°ii;a3-47> - o-°"8"
(cl + + 4c,
a = tan-1 V^ - 30.01° * 31.61'
Let a - 30'
0.4/0.12
- 7.70 ft
c * 0.5(0.866025)
M-22
EM 1110-2-2502
29 Sep 89
Ä
A - 2(0.4) 0
u 25940"*
0.12(25.70) -"y«UJ
- \ + 0.259403
c =
l °-50 • c
2 0.259403 0.036249
c c
a = 1-l(
tan'M —
l W^
l * 4c -/- 29.43° 4 30°
V 2—
Let a - 29°:
0.4/0.12
c 0.484810(0.874620) = 7.86 ft
A
- 0.12(25°86) - °'257798
- j + 0.257798
c 5 c
l " °' • 2 0.257798 = °-030248
c
a = tanri( iW;lj^).29>01,
a - 29° (nearest degree),

————— " d c - ————-
7.86 ft
b. Earth pressure coefficients and earth force for a » 29" (see

Appendix H).
1 - tan <J>, cot a

K
' 1 + tan *,a tan a " l'°°
K . K ( tan « \ . (%&$&) - 1.8215

1 \tan a - tan ß/ \0.304309/
M-23
EM 1110-2-2502
29 Sep 89
+ I tan g I Vis
\tan a - tan ß ~ )\y
¥L = il nnfi +
+ f0.554309 ,\ 0.120 1 = 2.5773
S '°°[; VO.304309 - V 0625J
EE (l/2)KlYm(h - hs - dc)2 + (l/2)hs[2KlYa(h - hg - dc) + VbhJ
h 18 ft, h = 10 ft, d = 7.86 ft

s c
?
EE (1/2)(1.8215)(0.12)(0.14)2 + (1/2)(10)[2(1.8215X0.12)(0.14)
+ 2.5773(0.0625)(10)1 = 8.362 k/ft
M-24
EM 1110-2-2502
29 Sep 89
c. Check solution by Iteration of Equation 3-23.
0.06(h2 - d*) 0 25
tan a — tan 8 tan a
C /Y
d m 3.3333
c sin a cos a sin a cos a
L = 7-
cos a (tan a - - tan g)
5V , Pw - i
2 Y'wh s = 3.125 k/ft
From Equation 3-23
P__ = W tan a - c. L/cos a - P

EE d w
Let a - 28°:
3.3333 m 804 ftt h2 _ d2 _ 259.3584

c 0.469472(0.882948) ' c
L =
9.96 =
0.882948(0.281709) *0-0427 ft
= 0.06(259.3584) 0.25 = 55>7098 k/ft

W W W
0.281709 0.531709 '' '
P„ - 55.7098(0.531709) - 0.4(40.0427)/0.882948 - 3.125
PEE - 8.356 k/ft
M-25
EM 1110-2-2502
29 Sep 89
Let a = 29°:
3.3333
d = = 7 86 ft
c 0.484810(0.874620) '
h2 - d2 = 262.2204 , L = 0.87462^304309) = 38 0981

' ft
= 0.06(262.2204) 0.25 =
K rc
0.304309 0.554309 ^•^^ '
P£E = 52.1525(0.554309) - 0.4(38.0981)/0.87462 - 3.125
PEE = 8.360 k/ft > 8.356
Let a - 30°:
d 7 70 ft h d 264 71
c - 0.5(0:866025) = ' ' " " c = '
L 0.866025(0.327350) " 36 3
- 324 ft
u - 0.06(264.71) 0.25 _ /B „._ ....

W +
0.327350 0.57735 = 48 9517 k ft
' '
P£E = 48.9517(0.57735) - 0.4(36.3324)/O.866025 - 3.125
PEE - 8.356 k/ft < 8.360
Iteration of Equation 3-23 shows that:
= 29 (to nearest
"crit ° degree), P£E = 8.360 k/ft
M-26
EM 1110-2-2502
29 Sep 89
which agrees with the pressure coefficient solution.
d. Conclusion. Use the moist unit weight of soil (y ) in the cohesion

terms of Equations 3-28, 3-29, and 3-24; even if the soil is partially-
saturated.
M-27
EM 1110-2-2502
29 Sep 89
M-6. EXAMPLE 6. Find the lateral earth forces on Surfaces CD and DE

(stratified soil).
10
tana2-tMß2
Y, = 0.12 KCF
4>, = 35°
SMF = 2/3
Yz ~ 0.13 KCF
*2 *208
SMF = 2/3
*d2 * 13.64°
a. Calculate a (see Appendix G). Using Equation G-25 from Appendix G
.. .fIiÜL + Y , 2Yi tan

(tana Bi- 'tan""ß 0
?
T. . 2(0.12)(13) +on+
2(0
■< -1) 0.442 +
0.04
tan a2 - ^ tan a2 - %
The weight of the surcharge in triangle ACZ is calculated by using

Equation G-26.
M-28
EM 1110-2-2502
29 Sep 89
Y^ (tan ßt - tan ß2) -0.12(H))2 (±) ^
(tan
V a.2 - tan B.V
2) _2 ^tan
/ 1\2
a2 - jj /
^tan l\2
o2 - ^
First trial: oui - 39° , Y* - 0.5042 , V a = -2.4178
From Equation G-27
2V (l + tan2 ()»JO)
A - tan * -^
Y h2
A' - 0.242665 - 2(-2.4178) (1.058886) = Q^n9

0.5042(10)
From Equation G-28
4Va tan B2 (l + tan2 »J

2 tan * -2
C
l Ä?
, 4(-2.4178)(|)(l.058886)
2(0.242665) ^ =
c. 0.5042(10)2 =
c u,,wwo
l 0.344219
From Equation G-29
2Va tan2 ßjl + tan2 ^

)
tan 4>d2(l - tan <|>d2 tan $2 J - tan 62 +
it.2
Y'h2
c
2 r
M-29
EM 1110-2-2502
29 Sep 89
jv l 2(-2.4178)(^)(l. 058886)
0.242665(l - 0.242665
*' * 0.5042(10)2
0.344219
c^ = 0.184077
c 2+
a„ = tan -1U+V i W [G-30]
a2 = 35.1° ?« 39°
Second trial: a£ = 33° , Y' - 0.5249 , Vffl = -4.2911
A. = 0.242665 - °-02"7;^-2911) = 0.415797

0.5249
0.007059(-4.29U)
0.117773 -
■ '
0.5249
<c 0.422035
0.415797
0.000588(-4.2911)
0.066814 +
0.5249
= 0.149128
0.415797
a2 = 33°
b. Calculate a1 .
c, - 2 tan *.. = 2(0.466308) = 0.932616 [3-26]

1 dl
c2 - 1i - ..tan *Adl ..tan Qß - -^^^j-

tan g [3-27]
c2 - 1 - 0.466308(1/3) - ^-^f^ - 0.129729
M-30
EM 1110-2-2502
29 Sep 89
°1 " 46.547°
c. Calculate lateral earth pressure coefficients (see Appendix H).
Wedge 1:
_ 1 - 0.466308(0.947407) ^
u J/ uyi
* 1 + 0.466308(1.055513) - «
KI - °-37409i(offfM)" °'5468
Wedge 2:
IT « 1 - 0.242665(1.539865) _ ft
u
-Alfti;,
* 1 + 0.242665(0.649408) -^luoJ
*i - °-5"°"(oM$!) • ••»«
Kv - 0.541063(0.649408) - 0.3514
d. Calculate lateral earth forces and pressures.
Wedge 1:
h2 (tan ßj - tan &2)

h - h.„ - h, +
AB 1 (tan a - tan ß_)
h
AB = 13 +
(i-i)
(io) w
0.649408"- 0.166667 " 16 452
' ft
1 2
P K Y h
EE1 * 2 l l
PEE1 " I (0.5468)(0.12)(16.452)2 = 8.88 k/ft
M-31
EM 1110-2-2502
29 Sep 89
Put, - K.y.h.. = 0.5468(0.12) (16.452) - 1.0795

Ho 1 1 AD
Wedge 2:
Treat weight of ABCD as a strip surcharge on Surface BD,
V =
I ^1+\B)(AZ)(Y1)
V = j (13 + 16.452)(20.715)(0.12) = 36.606 k/ft
_ 1 2
P K
Y ~ 2 l^2h2
P = | (0.7279)(0.13)(10)2 - 4.73 k/ft
P_ - K V
V v
Pv - 0.3514(36.606) - 12.86 k/ft
Pô
EE2 - P Y + P„
V - ^-73 + 12.86 = 17.59 k/ft
P Y h
VD * l l
p = 0.12(13) = 1.56 ksf - vertical pressure at D
P = K P
HD 1 VD
pur. = 0.7279pT7T. = 1.1355 ksf = horizontal pressure at D

HI) VI)
(P + P
2 HD HE) h
2 = P
EE2
M-32
EM 1110-2-2502
29 Sep 89
2P.EE2
•HE - P.HD horizontal pressure at E
2(17.59)
'HE 10 - 1.1355 - 2.3825 ksf
Pressure distributions on Surfaces AB and DE
KSF
e. Earth pressure on Surfaces CD and DE. The earth force on AB may be

transferred to Surface CD by assuming that no shear resistance is developed on
Surface BD. Then to obtain moment equilibrium for Block ABCD, a vertical shear
force must be developed on Surfaces AB and CD. The shear force will be:
tan ß1+ tan ß;

7
CD *EEl'
M-33
EM 1110-2-2502
29 Sep 89
A free body of Block ABCD is shown below.
20.7«'
V = 1973 K,FT
AB
\/CD = 8.88 (1/3+ 2/6)

PEE = 8.88 K/FT
3
i » . i = 1.973 K/FT
^
CO
N. •<»■ PeE1 = 8.88 K/FT
05
», B
CD *—
« i ,
■*
' f rt i
IMD= 0
IM.D = 8.88(8.937 - 4.333) - 1.973(20.715) = 0.013 « 0
The pressure distribution on Surfaces CD and DE is shown below.
2.3825 KSF
M-34
EM 1110-2-2502
29 Sep 89
M-7. EXAMPLE 7. Find the lateral earth force and pressure distribution on
Surfaces FG and HI when: ty = 35°, c = 0 , y = 0.12 kef, and SMF = 2/3 .
IB- IB'
t " T
a. Driving side:
(1) Assume that the critical slip plane intersects Surface BC. ß = 0 ,
h = h = 30 ft. The weight of the triangular area CEF will be taken as a
E
negative strip surcharge. V = - (1/2) (0.12) (6) (2) = -0.72 k/ft
<J>d = tan'1 (— tan 35° j =25°, tan (|>d = 0.466308
From Equation 3-30
M-35
EM 1110-2-2502
29 Sep 89
2v(l + tan2 4^)

A - tan $d - -—
yh
A « 0.466308 - »H»-™) (1.217443) . 0#482541

0.12(30)Z
From Equation 3-28
2
2 tan <)>.
—
c1 A
r
C
. 2(0.466308)2 _ . 901242
„,,.,
l 0.482541 " O'
From Equation 3-29
tan $.
c
2-—r~
0.466308 . ft,,oeft
C
2 " 0^82547 " °'966359
_1(c1 + ^c2 + 4c
a' - tan M — ^ ± I. 56.866° < 59.036°
This shows that the critical slip plane does not intersect Surface BC.
(2) Assume that critical slip plane intersects Surface AB. tan ß
(1/3) ft. The weights of areas BDE and CEF will be taken as
./3) , h = h = 36 ft
a negative strip surcharge
V = -i (0.12) (18) (6) - -| (0.12) (6) (2) = -7.2 k/ft
M-36
EM 1110-2-2502
29 Sep 89
From Equation 3-30
A . 0.466308 - »<-7.1)<1.217W) . „.579034

0.12(36r
From Equation 3-28
9 A(-7.2)(- i)(l.217443)
2(0.466308)Z ^-^ =
r
C
0.12(36)Z
l 0.579034 0.621268
From Equation 3-29
T / i\l / 1\ 2(-7.2)(|)(l..217443)
0.4663081II - 0.466308 (-■£)- (-4)+ —
L \ J/J \ 3/ 0.12(36)2
c„ »
2 0.579034
c2 - 1.484537
c + 2
+ 4c
a -
-i[
tan V
i yR
ö
2 , „ ,,„.
/ • 57.473
33.69° < a < 59.036°
This shows that critical slip plane does intersect Surface AB.
(3) Calculate the pressure coefficients (see Appendix H).
1
v » " ta" *d COt " = 1 - 0.466308(0.637733) . „.-
1 + tan ♦ tan a 1 + 0.466308(1.568054) "•*»U3"°
h - * U T. L..) - °-«>5858 MB) - °-""°7
M-37
EM 1110-2-2502
29 Sep 89
Kv = K tan a - 0.405858(1.568054) 0.636407
P - K Yh
Y I l D " 1 (°'334707)(°«12)(36)2 " 26.027 k/ft
P - K V - 0.636407(-7.2) = -4.582 k/ft

v v
P_ - P + P = 26.027 - 4.582 - 21.445 k/ft
(4) The net horizontal pressure at point F must be equal to zero, the
negative pressure due to P cancels the positive pressure due to Py .
p _, - 0.334707(0.12)(8) - 0.3213 ksf, p _ = -0.3213 ksf

yr Vr
2P
2( 4
h (distribution length for P ) - —- = " :^^ = 28.52 ft
v' pvF -0.3213
PEE = 21.445 K/FT
KSF KSF
P. COMBINED
b. Resisting side;
(1) Calculate the critical slip plane angle a .
tan ß - - -r , tan $, - 0.466308
M-38
EM 1110-2-2502
29 Sep 89
From Equation 3-38
A - 0.466308
From Equation 3-36
2
2 tan 4>.
d
c, -
'1 A
r
C
. 2(0.466308)2 _ _„,.,
l 0.466308 0.932616
From Equation 3-37
tan $. (1 + tan <J>. tan ß) + tan 6

a a
C
2 A
0.466308 I 1 + 0.466308 (- |)J + (- ~)

c2 0.466308 0.347297
a - tan■■■(-^f"
1
I —= V"1 '). 15.917-
-/- 15.917° [3-35]
•(2) Calculate the pressure coefficients (see Appendix H) and pressure

distribution.
1 + tan 0d cot a j + 0.466308(3.506578) nvmfi

J Ujyji0
* " 1 - tan *d tan a * 1 - 0.466308(0.285178) * -
K = K ( tana \ , (£|S5"|) . L619547

1 Vtan a - tan 8/ \0.535178/
M-39
EM 1110-2-2502
29 Sep 89
-ilGjh* = -| (1.619547) (0.12) (8)" = 6.22 k/ft
The calculation of the passive force and pressure distribution as performed

above is adequate for performing a sliding analysis but should be calculated as
described in paragraph 3-8 when performing an overturning or bearing capacity-
analysis and for design of structural members.
PRESSURE DISTRIBUTION
1.5548 KSF
M-40
EM 1110-2-2502
29 Sep 89
M-8. EXAMPLE 8. Find the lateral earth force on the wall when:
1. <|> = 30°, C = 0 , Y = 0.120 kef, SMF = 2/3
2. <j> = 0 , c = 0.60 ksf, Y = 0.120 kef, SMF = 2/3
a. <|> = 30°, <|> = tan"1 (2/3 tan (|>) = 21°, tan <|> = 0.383864.
(1) Since the tan ß for Surface BE is 0.5 which is greater than
tan <(> , the critical slip plane will not intersect BE. Assume that the slip
plane intersects Surface AB:
tan ß - 0 , h - hjj 64 ft
V = - i (0.12)[64(32)] - -122.88 k/ft (negative weight of area BDE)
From Equation 3-30
2VU + tan2 <|>d)

A ■ tan <J>,
M-41
EM 1110-2-2502
29 Sep 89
A = 0.383864 - 2(-122.88) (1.147352) = ^^

0.12(64)2
From Equation 3-28
?
2 tan ' <J>,
d
C
l Ä
c 1 = 2^00.957540
-38386^2 = oO.W///1
307771
From Equation 3-29
tan <(>,
C
2 - JnfPBS ■ 0-^0886
(Cl
a = tan -1 \-±
+ C
\*-J.
1 + 4c
2L \1 =
38.85i-
33.69° < a < 45°, assumption that slip plane intersects Surface AB is correct.
(2) Calculate the pressure coefficients (see Appendix H)
= * - tan *d COt ' = 1 - 0.383864(1.241485) _ Q „^

1 + tan * tan a 1 + 0.383864(0.805487) " u'jayBi0
Kv = K tan a = 0.399816(0.805487) ■= 0.322047
P - -| Kyh2 = | (0.399816)(0.12)(64)2 = 98.26 k/ft
M-42
EM 1110-2-2502
29 Sep 89
P = K V = 0.322047(-122.88) = -39.57 k/ft

v v
P + P = 98.26 - 39.57 = 58.69 k/ft
"EE Y v '
(3) The net pressure at point E must be equal to zero. The negative
pressure due to P cancels the positive pressure due to P .
0.399816(0.12) (32) = 1.5353 ksf

' yE
-1.5353 ksf
"vE
2P„ 2(-39.57)
hv (distribution length for Pv) = 51.55 ft
-1.5353
P£E = 58.69K/FT
M-43
EM 1110-2-2502
29 Sep 89
b. $ - 0 , c « 0.6 ksf, c. - 2/3 » c » 0.4 ksf.
(1) Assume that the vertical crack extends upward from the critical slip
plane to intersect Surface BE.
tan 0 - 0.5 , h - h- 32 ft
From the equations given in Appendix H
1 - tan <fr, cot o

„ _ d tan o _ tan a
1 1 + tan $. tan a tan a - tan (3 tan a - tan 6
a
tan a
K -
c 2 sin a cos a (1 + tan <L tan a) tan a - tan 6
d
„ 1 tan a
c 2 sin a cos a tan a - tan 6
From Equation 1-2
2 C /Y
d Vd„ d
c K-Y sin a cos a
.
(J is ■■•
0.4/0.12
i i ■ * m
3.333
'
ft
c sin a cos a sin a cos a
3.333
Assume that a « 45°, then d • n' ± « 6.667 ft
c U.J
From Equation 3-30
Y(h + dc)
M-44
EM 1110-2-2502
2 9 Sep 89
A
0.12(38.667) "•*'*»"
From Equation 3-28
Ac, tan ß
d
c, ■
'1 Y(h + dc)
4(0.4)(0.5)
m 0.12(38.667) m
c l,w
l 0.172412
From Equation 3-29
2c
- tan ß +
Y(h + d )
C
2 Ä ~
-0.5 +—^^-
.
C
_ 0.12(38.667) qnnmn
2 0.172412 -1.900030
The term under the radical in Equation 3-25 will be negative. This makes a
indeterminate, so the assumption that the crack intersects Surface BE is not
correct.
(2) Assume that the vertical crack intersects Surface AB.
tan ß - 0 , h - h, - 64 ft, V = -122.88 k/ft (negative weight of area BDE)

d
Again assume a = 45°, d = 6.667 ft

c
From Equations 3-28, 3-29, and 3-30
M-45
EM 1110-2-2502
29 Sep 89
2C
A- <
Y(h + d c>-^77)
A 2(0«*) _ 2(-122.88) _
0.12(70.667) 0.12(4051.55) "•a»*8«
C C ,U 2Cd J /AA , 2(0.4) / ,

l " ° ' 2 " Y/
r(h -*•
+ <y^ /' A * 0.12(70.667)/"-
" .')■■««■» / 0.599825 = 0.157278
-1 ( Cl +
\C1 + 4c
2 I
a - tani * \—
I S-i
*Y -)~ 21.63° +■* 45°
-/- [3-25]
= 9 727 ft
Let ««=21.63° , dc = Ö75Ü55 '
A = 2(0.4) _ 2(-122.88) _
A
0.12(73.727) 0.12(4001.39) " °'*°"*b
c2 =
cL - 0 ,
02^727T/ -
0 602246
- °-150144
C + C + 4c
a = tan -1 II —l \i_i1 2£ I1 = 21.18° ^ 21.63
Let a = 21.18° , dc - £g^ - 9.893 ft
2(0.4) 2(-122.88)
A =
" 0.12(73.893) " 0.12(3998.13) °-602460
Cl " ° ' C
2 ' 0.12(?3?893) /..,
' °-60246° =
°'149754
M-46
EM 1110-2-2502
29 Sep 89
a - 21.15° 4 21.18'
3.333
Let a - 21.15° , d - 9.90 ft
c 0.336506
2(0.4) 2(-122.88)
0.602469
0.12(73.90) 0.12(3997.99)
cx - 0 , c2
öTTfa3T9Ö)/°-602469 = 0 149737
-
a - 21.15" , d - 9.90 ft
Check to see if crack intersects Surface AB.
dr = 9-90'
Assumption that crack intersects Surface AB is not correct.
(3) Assume that the crack intersects the sloping surface to the left of
point A.
tan B - - j , h - hc - 96 ft, V - - ± (0.12) [(64) (32) + (96) (32)]
V - -307.20 k/ft (negative weight of areas ACD and BDE)
Let a - 30° , dc = ^j^ - 7.70 ft
M-47
EM 1110-2-2502
29 Sep 89
From Equation 3-30
2c, (1 - tan $ tan ß) _„

A _ Q ZV
V^5
2(0.4) 2(-307.20)
=
0.12(103.70) " 0.12(9156.71) °»WM*i
From Equation 3-28
Ac. tan 8 ._ t
d 4V tan p0
Y(h + d
y/n2 - d2.
c
1
c>
A
£i£L
4(0.4) (- j) 4(-307.20)(- ±)
c =
0.12(103.70) 0.12(9156.71) . ,,,,,,
l 0.623441 0.666666
From Equation 3-29
2c 2
tan
*-*„ ßfi +
7(F -V
d
+■ 2V tan ß
^T^
C =
2
( M, 2(0.4) , 2(-307.20)(i)
1-
C
V sy 0.12(103.7) * 0.12(9156.71) = 0f538132
2 0.623441
a ■ tan -1 fcl +
\cl + 4c
2j
a = 25.29° * 30°
M-48
EM 1110-2-2502
29 Sep 89
Let a * 25.29° , d = J'Jtll** - 8.63 ft
A
Ä
, 2(0»*) _ 2(-307.2) =
0.12(104.63) 0.12(9141.52) *>•<>•«'*»
4(0.4)(- |) 4(-307.2)(- ±)
„ _ 0.12(104.63) " 0.12(9141.52) n ,,,,,,
cx 0.623799 0.666666
( l\t 2(0.4) , 2(-307.2)(i)

c2 = "V-3; 0.12(104^3)^ 0.12(9141^52)_ m ^^
a = 25.25° t 25.29*
. O j« -J • J<J^J
Let a = 25.25° , dc = 0<385812 = 8.64 ft
A _ 2(0.4) 2(-307.2) _
U,OOOUJ
0.12(104.64) 0.12(9141.35)
4(0.4) (- i) 4(-307.2)(- |)
c =
0.12(104.64) 0712(9141.35) A ,,,,,,
l 0.623803 0.666666
( IN, 2(0.4) , 2(-307.2)(i)

_ " V" 3/ 0.12(104.64) 0.12(9141.35) n «.,A7,,
c2 0.623803 0.536726
a = 25.246° » 25.25° , d c - 8.64 ft
M-49
EM 1110-2-2502
29 Sep 89
(4) Calculate pressure coefficients (see Appendix H) and earth forces:
1 - tan +d cot g x . 0(2.120303)

K s
1+ tan A. tan o " 1 + 0(0.471631)
K
K - V ( tan a
"\ = 1L f°-471631>\ = o 585903
l " K Uan a - tan 0/ V0.804964/ "^"^
K - K tan a - 1(0.471631) - 0.471631

v
P - | KlY(h - d V - \ (0.585903)(0.12)(96 - 8.64)2 = 268.29 k/ft
P =KV = 0.47163K-307.2) = - 144.89 k/ft

v v
P^ «= P + Pv - 268.29 - 144.89 - 123.40 k/ft

EE Y
(5) Pressure distribution. The negative horizontal pressure, due to

P , at point E must cancel the positive pressure, due to P .
p = 0.585903(0.12)(64 - 8.64) - 3.8923 ksf

yE
pr ,. = -3.8923 ksf
vE
= 74,45 ft
hv = distribution length for Pv = ^^^
M-50
EM 1110-2-2502
29 Sep 89
8.64' = flfc>
P=123.40K/FT
KSF
COMBINED
M-51
EM 1110-2-2502
29 Sep 89
M-9. EXAMPLE 9. Compute lateral earth pressure using pressure coefficients.

Check by wedge method.
BACKFILL:
y = 0.12KCF
0*35°
C=0
SMF = 2/3
4>d*tair1(2/3tan«>J = 25e
a. Find critical slip-plane angle. Consider basic wedge to have height

of 20 feet (h ), with sloping top surface (tan ß = 0.4). The weight of
c
triangle ABC will be considered a finite surcharge (V).
V - ~ (0.12) (10) (4) - 2.4 k
From Equation 3-30
2v(l + tan2)*
2(2.4)(1.217443)
A ■ tan <fr. - - 0.466308 -
0.12(20)2
A - 0.344564
From Equation 3-28
M-52
EM 1110-2-2502
29 Sep 89
4V tan ß (l + tan2 4#d)

C 2 tan <(ij -
l -
y<
2(0.217443) - 4(2.4)(0.4)(1.217443) * 0.344564

0.12(20)2
-Cj = 0.979471
From Equation 3-29
2V tan2 ß (l + tan A.]2

tan A. (1 - tan <j>, tan ß) - tan 6 + * A
Yh
c = 0.466308(1 - 0.466308 x 0.4) - 0.4 + 2(2.»)(0.16)(1.217443)

2
0.12(20)
i 0.344564
c2 = -0.003454
c +
a - tan
-if i V?^ 4c, 44.302' [3-25]
b. Calculate earth pressure coefficients (Appendix H),
1 - tan »d cot a t _ 0>466308 x 1>024667
1 + tan <j>d tan a ~ 1 + 0.466308 x 0.975927
K - 0.3589
M-53
EM 1110-2-2502
29 Sep 89
v v /_tana_\ _ ,_QQ /(L975927\ ,nQO

K. ■ K I- T 1 = 0.3589 I n cTcfto? I
= n
0.6082
1 Vtan a - tan ß/ \0.575927/ ————
The earth pressure distribution is calculated in the following figures.
1.4597 KSF 1.4597 KSF E
M-54
EM 1110-2-2502
2 9 Sep 89
c. Check pressure using the wedge method.
2.5
10'
Ü
. A G B
V£ 1
■
> S
d
a»
I ,l
R
a f\. ii ■ I
u
CRITICAL SLIP D ü
xz I
PLANE
5
II
II Ui
lu
Q
flr = **.302"X. I i i'
Force on Surface BC.
Yh BC
Weight of wedge GBC « W 0.12(4)* - 0.9837 k
2 tan a 2(0.975927)
From Equation 3-23
W (tat>
» ° " ta" V 0.9837(0.975927 - 0.466308) ,
BC * 1 + tan ♦. tan a " 1 + 0.466308(0.975927) " u,JO
Force on Surface BD.
Weight of wedge ABB ■ W ± (0.12)(10)(9.76) - 5.8560 k
M-55
EM 1110-2-2502
29 Sep 89
P . 5.8560(0.975927 - 0.466308) , oq.

A u:3i K
BD 1 + 0.466308(0.975927) '
Force on Surface BE.
E
Weight of wedge FABE = W = 2 (tan\° _ tan ß) + \ (0.12) (10) (4)
WW - 0.12(20)2 + 2 4 = 44 0719 k
2(0.975927 - 0.4) + Z*4 «*.0719 *
P _ 44.0719(0.975927 - 0.466308) ,*****,

BE " 1 + 0.466308(0.975927) " iX*-" *
Calculate pressures at C, D, and E.
„ _ 2PBC _ 2(0.345) 17„ . ,

VrC " -r—
h
= 7
4
= n0.1725 ksf
BC
2(P P
_ BD " BC) 2(2.051 - 0.345) ftl„- n/100. f
P P
D h^ C 5T76 °*1725 =
°-41" ksf
2(P P
m BE - BD) _ = 2(15.435 - 2.051) _ =
PE . pD 14>24 u.îyy l.^yy Ksr
DE
The pressure diagram-wedge method is shown on the following page.
M-56
EM 1110-2-2502
29 Sep 89
/ B
fy—0.172SKSF *'
c
~^0.419^SF
D
Si
'I '
1.4599
KSF
Checks combined pressure diagram obtained using pressure coefficients.
M-57
EM 1110-2-2502
29 Sep 89
M-10. EXAMPLE 10. Calculate lateral earth pressure. Use the approximate
wedge method as well as the elastic method to find pres-
sure due to the distributed finite surcharge.
V = 6x0.5 = 3K/FT
/8 = 0
\ 0.5 KSF~+j[~
BACKFILL:
y = 0.12KCF
* = 35°
c=0
SMF = 2/3
<Dd = tan-1(2/3tan<t>; = 25°
"W
a. Find critical slip-plane angle and lateral force using pressure

coefficients. From Equation 3-30
2V (1 + tan » ) 2(3X1.217443)
A = tan 4> 5 = 0.466308 ~—
d Z
yti 0.12(25)
A = 0.368913
From Equation 3-28
2 tan »d 2(0t466308)2
C
l A 0.368913 1-178832
From Equation 3-29
M-58
EM 1110-2-2502
29 Sep 89
ta
cC - "*d = 0.466308 = 1 2640
2 A 0.368913 ""*w»
-1 ( cl +
\cl + 4c
2L
a -tan I— V \ - 61.721° [3-25]
From Appendix H, the pressure coefficients are:
1 - tan 0d cot g x _ 0466308 x 0.537972

=
1 + tan ^d tan a 1 + 0.466308 x 1.858833
K = 0.4013
K - K tan a - 0.4013(1.858833) = 0.7459
P = -| Kyh2 = | (0.4013)(0.12)(25)2 = 15.05 k
Pv - KvV = 0.7459(3) - 2.24 k
H. _ ,. - P + P - 15.05 + 2.24 - 17.29 k

(total) Y v —————
Approximate method-pressure distribution for surcharge (see Figure 3-29).
M-59
EM 1110-2-2502
29 Sep 89
CRITICAL SLIP
PLANE WITHOUT
SURCHARGE
LINE OF ACTION
APPROXIMATE
PRESSURE
DISTRIBUTION
b. Find pressure distribution due to surcharge using the elastic method

(see Figure 3-27) . Assume nonyielding wall.
M-60
EM 1110-2-2502
29 Sep 89
xt»-*
2
' ~
_ 2
2' = X,
r"
q = 0.SKSF
' ♦ t t
\ \«\ a
a \ N
"
\.
2
9
*pHz=rfe -sin £ cos 2a)
22
ApHz, ksf
z ft ß , rad a°
1 25 0.3183 0.4036 75.96 0.239

2 50 0.3183 0.5932 63.43° 0.296
5 00 0.3183 0.6316 45.00 0.201
7 50 0.3183 0.5570 36.69 0.113
10 00 0.3183 0.4773 26.57 0.064
12 50 0.3183 0.4107 21.80 0.039
15 00 0.3183 0.3574 18.43 0.025
17 50 0.3183 0.3150 15.95 0.017
20 .00 0.3183 0.2808 14.04 0.012
22 .50 0.3183 0.2530 12.53 0.008
25 .00 0.3183 0.2298 11.31 0.006
M-61
EM 1110-2-2502
29 Sep 89
Pressure diagram-elastic method.
0239 KSF
0.006
The force, due to the surcharge, determined by the approximate method is more
severe. It will be combined with the backfill force to obtain the total force.
M-62
EM 1110-2-2502
29 Sep 89
Combined pressure diagram and force:
0.0448 KSF
Ky = 0.4013(0.12)
0.2316 KSF
0.4185 KSF-
1.2039 KSF 1.2039 KSF
BACKFILL COMBINED
M-63
EM 1110-2-2502
29 Sep 89
M-ll. EXAMPLE 11. Find the lateral forces and pressures acting on the wall
for the seismic condition.
Soil properties (on both sides of wall):
Y = 0.12 k/ft (moist weight)
Yv, = 0.0625 k/ft (buoyancy weight)
Y» - 0.125 k/ft (saturated weight)
35° , c = 0
Seismic coefficients:
k = 0.20
H
k = 0
v
M-64
EM 1110-2-2502
29 Sep 89
a
* Find forces acting on driving side.
2 (tan * - y 2(0>
(o 8
1 +-y°'° -?:S - 0.877526 [3-57]
1 1 + 1^ tan <f> 0.2(0.700208)
tan (J) (1 - tan $ tan g) - (tan g + k, )

[3-58]
tan <j) (1 + k, tan <())
0.700208 (l - 0.700208 x |) - Q + 0.2J

004315
0.700208(1 + 0.2 x 0.700208) * °*
C + c. + 4c2
a = tan -1 ( l V = 41.426' [3-56]
1 - tan j> cot a 1 - 0.700208(1.133240)

1 + tan <(. tan a ~ 1 + 0.700208(0.882425)
K = 0.12763
KA = K(- ^2_2 ) = 0.12763 /- 0.882425 > - 0.2051 [3-54]

A ytan a - tan BJ lQ 882425 - jj
K, = K 1 + (\tan a ^2-2
- tan g
A /_I_\
/ \y. J
(see Appendix H)
b
(0.882425 A / 0.12 \ 0.2764

h = 0.12763 1 + \0.549092 " 7 V0.0625/
P
A - I- V(h - hs)2 + I (hs) [2KY(h - V + Vbh.]
= [3-69]
M-65
EM 1110-2-2502
29 Sep 89
PA = | (0.2051)(0.12)(13)2 + i (12) [2(0.2051)(0.12)(13)
+ 0.2764(0.0625)(12)]
P.A - ————
7.16 k
Y)h
Yti <\ ~ S
&P
AE - \ 2 (tan a - tan 8) 2 tan a [3-71]
0.12(25)2 0.005(12)2
AP
AE = °- 2
2(0.549092) 2(0.882425) = 13.74 k
2 2
P„
wsc = 4I Ywh s - \Z (0.0625)(12) = ————
4.50 k [3-70]
b. Find forces acting on resisting side.
2 (tSn
„ . * V _ 2(0.700208 - 0.2) _ [3-60]
1 1 + 1^ tan ♦ 1 + 0.2(0.700208) " u-0//^°
From Equation 3-61
tan
c„ =
-\
2 tan 4» (1 + \iL tan 4>)
0.700208 - 0.2
c„ =
2 0.700208(1 + 0.2 * 0.700208) = 0.626618
C +
a = tan-l(- l >/Cl+4c2J - 24.999° [3-59]
M-66
EM 1110-2-2502
29 Sep 89
From Equation 3-77
K - 1 + t"» * cot a = 1 + 0.700208(2.144605)

T» " 1 - tan ♦ tan a 1 - 0.700208(0.466286)
- 3.7144
*P
From Equation 3-73
K
Pp - j p^bn2 - \ (3.7144) (0.0625)(6)2 = 4.18 k
From Equation 3-75
AP = 0 2 0-125(6)2l =
PE M2ârJ= - 2(0.466286)J u,y/
P = Y h =
ws 2 w s I (0.0625)(6)2 = 1.13 k [3-74]
c. Find inertia force due to weight of wall.
18' * 25' * 0.15 = 67.50 * 12.50' = 843.75
- ~ x 12' x 19» x 0.15 = -17.10 x 18.67' = -319.25

W = 50.40 k 524.50
524.50 .„ .. ...
y = = 10 41 ft
~5Ö^4Ö -
kjW = 0.2(50.40 k) = 10.08 k
M-67
EM 1110-2-2502
29 Sep 89
d. Summary of forces and pressure distributions.
f . ...k'i,i/f. -](2\ f ?.2(0.12)<25)> 1/2 \

L2(lan a - Ian flJ W 1.2(0.882425 - 1/3)J\25/ -0927 K!>
0.0625
/
/ 0.32
0.3233 KSF
.0.0625
-WS*'-"*
J.3929 0.37S
Permissible simplification for dynamic earth pressure distribution--driving

side:
The discontinuity of this pressure diagram, at the water table, may be

eliminated by considering that the soil weight above and below water is equal
to the moist weight. The difference is not significant.
1.0927 KSF In this case, the difference in

forces is -0.58% and difference
in dimension, Y„ , is +0.3 6%.
E
M-68
EM 1110-2-2502
29 Sep 89
Mononobe-okabe force and pressure distribution--resisting side.
If the pressure diagrams for P and AP (on the preceding page) are com-
P PE
bined, negative pressure will be obtained for some distance below the top of
ground. Since earth pressure can not pull on the wall, the pressure diagram
and force should be determined by setting all negative pressures to zero.
M-69
EM 1110-2-2502
29 Sep 89
APPENDIX N
STABILITY, BEARING CAPACITY, AND REINFORCEMENT COMPUTATIONS, EXAMPLES
SUMMARY OF EXAMPLES
Example 1, Page H-3 Example 3, Page N-24
3S
-am
EM Ö« 28°, e - 0 (DRAINED)
W J-Q . c « 0.9.KSF (UNDRAINED)
Example 2, Page N-18 Example A, Page N-41
. - 40°
e - 2.5 KSF 0- o
c . 0.9 KSF
N-l
EM 1110-2-2502
29 Sep 89
Example 5, Page N-52 Example 7, Page N-63
TOP OF WAVE
:x
"TfflSl Tsar
CRACK
CRACK
'0« 0
c = 0.9 KSF
Example 6, Page N-57
CRACK
£» 20* .
c - 0.4 KSF
N-2
EM 1110-2-2502
29 Sep 89
STABILITY, BEARING CAPACITY, AND REINFORCEMENT COMPUTATIONS, EXAMPLES

N-l. EXAMPLE 1. Analyze the wall shown below for stability and bearing
capacity. Find the reinforcement required at critical
sections. Load Case Rl.
Given:
Backfill: Y = 0.120 kef, <j) = 35°, c = 0
Foundation: y = 0.135 kef, <}> = 40°, c = 0
Reinforced concrete: 0.150 kef, f 4 ksi, f 48 ksi
All concrete cover = 4.5 in to center of gravity
of steel)
Load factor = 1.9, <|> = 0.9
20.00'
,2, 7.5'r.S' g,
sS
:V i i , i
Ni
f*
L* " H
l*:;
j
i 1«
c
;
> M*
ai »■:j
1 1
WM WM MM ,1 ^
(P.^.!.ifl...13.1.lV-'
>
8« SÄ
FOUNDATION
N-3
EM 1110-2-2502
29 Sep 89
a. Find critical slip-plane angles—driving side.
(1) Foundation (see Appendix G):
4 - 40°', SMF - 2/3 , *. - tan1 (2/3 tan *) = 29°

a
13.5'
The increased unit weight in the bottom layer (layer 2) is calculated as
2y,h1 2y, (tan ft, - tan 9>2)

T [G-25]
h0 '2 tan ct„ - tan 6.
ff = 2(0.12)-(26,5) + 0- 135 + 2(0,12) (1/3) ■■ 2>255 + J> .08

tan a. tan «.
Y^ (tan ßt - tan &2)

Va - [G-26]
2 (tan a - tan &2)
N-4
EM 1110-2-2502
29 Sep 89
0.12*3)^<l/3) „ -0.18
2 • ■
2 tan a„ tan a„
Let a2 = 59.5° = 45 + j- ,
Y' - 2.255 + ^^3 = 2.302,
°-18 „ - 0.0625
(1.697663)'
From Equation G-27 (omitting th£ c term>-
a(l + tan2 <frd)

A' tan <|>, -
.»2
Y'h
L, . 0.554309 - 2(0.0625)(1.307259) . Q>546422
2.302(3)
From Equation G-28 (omitting the c term)
(l + tan2 *Y(1>
4Va tan &2\l d)
2 tan <t>.d 5 A'
y'K
c* -= 2(0.554309) * 0.546422 - 1.12462
From Equation G-29 (omitting the c term)
N-5
EM 1110-2-2502
29 Sep 89
2V tat 2 l + tan2
\
tan ^(l - tan ^ tan ij - tan & 2 + a > *2(^ O
,
c. -, 1*2
c2 - 0.554309 * 0.546422 - 1.01443
fc' + ■v/ c|2 + 4c'

a2 - tan"1 I -* ^-1 £y „ 5g Jj0 x 59y [G_30]
Let a2 - 59.73°, y% - 2.302 , Va - 0.061
A, . 0.554309 - 2(0.061X1.307259) . 0>,464u

2.302(3)^
cj - 2(0.554309)2 * 0.546611 - 1.124231
c2 - 0.554309 * 0.546611 - 1.014083
a2 - 59.76° 59.73° (close enough)
a 59 76
2 " ' "
(2) Backfill:
3 tan 0.
h._
AB - 26.5 + -r^T^-
1
tan o_ " 27.083 ' ft, ♦ - 35«
tan 4>d - tan"1 (2/3 tan *) - 25°
Cj - 2 tan <|>d - 2(0.466308) - 0.932616 [3-26]
N-6
EM 1110-2-2502
29 Sep 89
tan ß.
c2 - 1 - tan 4d tan ^ - -^j- [3-271
I
_3_
c„
■1 ~- L1 ~- "•■♦""-
0.46630s(i)
" \3y - 0.466308
, u Q ti^na = 0.129729
«! = 46.55° 13-25]
b. Earth pressure coefficients (see Appendix H)
(1) Backfill:
1 - tan $, cot a. tan a,

K1 1 + tan 6. tan a. tan a^ - tan $^
_ 1 - 0.466308 * Q.947307 # 1.055624 _ Q 546g

K
l 1 + 0.466308 x 1.055624 * 1#055624 _ I ~ '
(2) Foundation:
1
" tan '''d COt a2 1 - 0.554309 * 0.582949 _ Q ,.?0
K =
1 + tan <K tan o0 " 1 + 0.554309 * 1.715416 " '
K = K tan a = 0.5952
v 2
c. Lateral pressure and forces on Surfaces AB and PE.
P = K Y h =
AB 2 l l AB \ (0.5468)(0.12)(27.083)2 «= 24.06 kips
N-7
EM 1110-2-2502
29 Sep 89
Surface DE:
P
DE - 1 *2b£ +
V
V
-I<hAB + h
CD)(Vy a2j
V - | (27.083 + 26 .5)(0.12)L ^5416J - 5.623 kips
P
DE " I (0.347)(0.135)(3)2 + 0.5952(5.623) = 3.5576 kips
PB = KjYjh^ - 0.5468(0.12)(27.063) - 1.7771 ksf
PD = KYjh^ - 0.3470(0.12) (26.5) - 1.1035 ksf
P
V
DE " fc
V 2 ; h2
2P„„
DE
PE
" "V" PD
PE = 1(3^762 _U1035
p„ - 1.2683 ksf
E
N-8
EM 1110-2-2502
29 Sep 89
= 1.749'
fano2
PRESSURE
DIAGRAMS
d. Shear force on structural wedge (paragraphs 4-8c, 9-7a).
(1) The horizontal force P will be considered to act on any vertical

plane in the soil that lies on Surface AB, or on any surface to the right of
Surface AB, such as surfaces CD or GH.
(2) In order for the body of soil lying between CD and GH to be in

equilibrium, a small vertical shear will be assumed to act on vertical surfaces
along with the horizontal force P„„ .
AB
(3) The value of this shear force is found from a free body of any block
of soil as shown on the following page:
N-9
EM 1110-2-2502
29 Sep 89
EM = 0 ? va
AB[3 " \3 ~ 9/J "
P._
AB tan 8 PAT> nt n,
va = P TT
v
- =
AB __ ——
_^ 24.06 _ 2.673 klps
.
ABVV *
e. Weight and center of gravity of structural wedge.
1.5 ft x 22 ft x 0.15 kef = 4.95 x 5.75 ft = 28.46 kips

j x 1.5 ACft x 22 ft x 0.15 kef 2.48 x 7.00 ft = 17.36 kips
20 ft x 3 ft x 0.15 kef = 9.00 x 10.00 ft = 90.00 kips
Concrete = 16.43 k/ft 135.82 ■*■ 16.43 8.27 ft
|x 13.5 ft x 4.5 ft x 0.12 kef 3.65 x 15.50 ft = 56.58

12 ft x 22 ft x 0.12 kef 31.68 x 14.00 ft = 443.52
1 X 1.5 ft x
2 22 ft x 0.12 kef 1.98 x 7.50 ft = 14.85
Soil 37.31 k/ft 514.95 37.31 13.80 ft
= x
N-10
^—
EM 1110-2-2502
29 Sep 89
f. Overturning stability (paragraph 4-8) .

C
v = 2.67 K/FT-
PAB = 24.06 K/FT

8.ZT-
n SOIL RESISTANCE
P0E = 3.56K/FT
f\ ON SURFACE U
NEGLECTED.
IH= 27.62K/FT ^Ft'7.34

0.5698 11
\\ 5.0713
KSF KSF
IV* 56.41 K/FT
2.67 kips x 20.00 ft ■= 53.400 ft-kips

37.31 kips x 13.80 ft = 514.878 ft-kips
16.43 kips x 8.27 ft - 135.876 ft-kips
56.41 = EV
_ 414.291 ,
/,J
-24.06 x n.83 *R 56.41 * "
-284.630
- 3.56 x 1.47 -5.233
-27.62 = IH 414.291 - ZM,
One hundred percent of base is in compression, overturning stability require-

ment is satisfied.
g. Sliding stability analysis (paragraph 4-15).
N' - IV - 56.41 kips, T « EH = 27.62 kips
N' tan (j) + cL

FS [4-12]
N-ll
-■—
EM 1110-2-2502
29 Sep 89
Using the minimum FS of 1.5 from Table 4-1 yields
97 f,7 < 56.Al tan 40" + 0 (20)

* " 1.5
27.62 S 31.56
Sliding stability requirement is satisfied,
h. Check bearing capacity (Chapter 5).
6 = tan_1(|^|j-) = 26° - 0.4538 rad (Figure 5-1 (a))
e«=|-xR = 2|- 7.34 - 2.66 ft
B = B - 2e - 20 - 2(2.66) = 14.68 ft
qQ = YD - 0.135(3) - 0.405 ksf [5-8a]
V - (x - k) - °-5057 f5-5ai
C
Yi= {l-TJ2 - (l-ff)' = 0.1225 [5-5b]
N = 64.20 , NY = 93.69 (Table 5-1)
Using Equation 5-2 yields
N-12
EM 1110-2-2502
29 Sep 89
Q - 14.68 [o.5057(0.405) (64.20) + 0-""(l».68)(0.135)(93.69)1
Q - 359.97 kips
For this problem IV - N' . The factor of safety is calculated as
FS
" h" THT = 6-38 > 3-00 [5-1]
Bearing capacity requirement is satisfied (Table 4-1)
i. Reinforcement at base of stem (Chapter 9). Neglect vertical shear

component v .
M = 24.06(7.33 ft) - 176.36 k-ft
M '
-f
u
/
k - 1 * , (Figure 9-2)
u
0.425f*bd2
c
M
u 1 9(176.36) (12) _ ,.
468 k-in.
* 0.90
PAB=24.06 K/FT b - 12 in., d - h - 4.5 - 3L.5 in.
0.425f'bd2 - 0.425(4)(12)(31.5)2 * 20;241.9

8 c
k 4,468
u " X - V>
'I i
0.1174
" 20,241.9
C - T - 0.85f'k bd
h = 3' = 36" U 11 c u
C - T = 0.85(4)(0.1174)(12)(31.5)
150.88 kips
. u'■'•'■ 150.88 , ,. . llc^

A =
s f ST- " 3-14 ln> /ft
y
N-13
EM 1110-2-2502
29 Sep 89
Check if ductility requirement of pmin s p s p^^ is satisfied:
p Xp X
max ' b ' " °*25 <Para8raPh 9-8b(3))
p 200/f
min " y " 200/48,000 - 0.00417 (paragraph 9-8b(4), from ACI 318)
The reinforcement ratio pb in the balanced condition may be obtained by

applying equilibrium and compatibility conditions. From the linear strain
condition shown below:
0.003
d e + c f
c y
0.003 + -- --?
29,000 ksi
The compressive force C is
C - O.SSf'&.bc.
c 1 b
The tensile force is
K
y sb b y
Equating C to T yields
0.85f*b8,c. - pvbdf
c 1 b b y
0.85f c. 0.85f*
-c +
29,000 ksi,
B^ ■ 0.85 , e ■ 0.003 (for nonhydraulic structure, paragraph 9-8e)
N-14
EM 1110-2-2502
29 Sep 89
0.003
% • HP <0.85) 48 0.03880
0.003 +
29,000,
P
max * °-25(°'03880) = 0.009700
A
3.14
P =r§
bd 12(31.5) 0.008307
0.00417 < p ■ 0.008307 < 0.009700
Ductility is adequate.
j- Reinforcement in heel at face of stem.
2.67 x 12.00 = 32.04

12' 1 35.28 x 6.16 - 217.32
■ * U -,6-16' i
5.40 x 6.00 - 32.40
-23.05 x 4.59 = -105.80
N
M = 175 .96 k-ft
C5 v- .6' t From Figure 9-2
85 M
u 1.9(175.96)(12)
= 4,458 k-in.
H
♦ 0.9
• h = 3' = 36" b = 12 in., d = 36 - 4.5 = 31.5 in
\
i 4.59'
^ * 0. 425f'J>d2 - 20,241.9
i
0.5698 3.2711
KSF KSF k
u
- 1 - Jl - *-458 "g - 0.1170
v 20,241
23.05K C = Tu = 0.85(4)(0.1170)(12)(31.5)
u
BRG. PRESS.
■= 150.37 kips
150.37 „ ,„ . 2
A = r= » 1.11 in /f,
48
Check ductility:
P
max " 0-009700 , pfflln - 0.00417
N-15
..
EM 1110-2-2502
29 Sep 89
8 3.13
P " bd
vT 12(31.5) 0.008280
0.00417 

(j, 0.9 '
T b - 12 in., d » 36 in. - 4.5 - 31.5 in.
0.425f'bd2 = 20,241.9
c
3.9465 L k 5.0713
KSF KSF
K'i-^'ÄMS*™*7 -
22.55K C -T - 0.85(4)(0.0337)(12)(31.5)
BRG. PRESS. u u
= 43.31 kips
A - Qß- - 0.90 in.2/ft

s 48 ■
Check ductility:
<W • °-02910 > Pmin - °-00417
» " bf " I2T3T3T - °-002381
0.00417 < p - 0.002381 < 0.009700
N-16
EM 1110-2-2502
29 Sep 89
1. Shear check (paragraph 9-8f). The shear capacity of the concrete

will be checked at a distance d from the base of the stem according to
ACI 318.
d = 31.5 - ^ d , 1.06818 d - 31.5

v 22 v v
d - 29.5 in. - 2.46 ft (member depth for shear at distance dy above

base)
Since the shear has a quadratic variation, the shear at distance dv can be
calculated as shown below.
2
(22 2 46)
V - " ; (24.06) - 18.98 kips
(22r
V - 1.9(18.98) - 36.06 kips
1 - (0.85) (2) /F bd (from ACI 318)
♦V = (0.85)(2)/47ÖÖÖ(12)(29.5) - 38,061 lb > V

c u
Check the shear capacity of the heel at the base of the stem:
V - 2.67 + 5.40 + 35.28 - 23.05 - 20.3 kips
V - 1.9 (20.3) - 38.57 kips
4>V - (0.85) (2) /fT bd

c c v
♦V - (0.85)(2)/47ÖÖÖ (12) (31.5) - 40,642 lb > V

c u
N-17
EM 1110-2-2502
29 Sep 89
N-2. EXAMPLE 2. Analyze the wall below for overturning, sliding and bearing
capacity. Case R2, unusual loading condition.
b = 30-
BACKFILL:
ym=0.12KCF;
ys = 0.125 KÖF,
0=35°
c=Q - ■-* *"
-in; w
■*«*
,1>^rt.lWk<I.W»l»»W.-"
P ROCK FOUNDATION:
ys=0.140 KCF
0=40°
C = 2.5 KSF
a. Driving side lateral pressure coefficients.

(1) Foundation:
SMF = j , $= tan" -1 (| tan <(>) = 29.22°
K = tan2 U5° - -|) = 0.3439 [3-15]
K c = <£ - 0.5865
p^ = 23.67(0.12) + 22(0.125) - 28(0.0625) + 6(0.14) = 4.68 ksf
N-18
EM 1110-2-2502
29 Sep 89
p = Kp 2K C C = C l 67 ksf
HD v " c d ' d 3 " '
PHD = 0.3439(4.68) - 2(0.5865)(1.67) - -0.3495 ksf
Negative horizontal earth pressure at D shows that there will be no earth

pressure on Surface CD. Also, no at-rest earth pressure can act on
Surface EF.
(2) Backfill:
SMF = | , $ tan ♦)
(t>d - tan -1* [(| <f> J = 25"
cl = 2 tan <|>d = 2(0.466308) - 0.932616 [3-26]
e2 - 1 - tan *d tan B - g-5- [3-27]
I
c,2 = 1 - 0.466308 x I6 - 0.466308
.* .„ - 0.564864
a = tan_i I— -l i ci+ VT
^ j= 53.49" [3-25]
1 - tan $, cot a
K.1 = ,1 +, tan
. T—z
<fr,
a
tan az ' ztan az - tan
r pD (.see Appendix H)
v 1 - 0.466308 x Q.740231 1.350929 . /coo , .

K =
l 1+0.466308 x 1.350929 * lt350929 . 1 * ^^ table)*™ "
b. Uplift and water pressures (paragraph 3-22, rock foundation assumed).

Since the total seepage path length is the base width, full hydrostatic pres-
sures will exist at points D and E (see paragraph 3-22).
N-19
EM 1110-2-2502
29 Sep 89
UJJ -,,28 ft (0,0625) -m 1.75 kgf.
uE * 16 ft (0;Cf625) = l.OO ksf
For the same reason the buoyant weights for backfill and foundation materials
are: ,-. ..„ .. .■:.-• .■.;■•-•- ..::-,f;-; ■
Yb (Backfill) =0.125 - 0.0625 - 0.0625 kef
Yfe (Foundation) = 0.140 - 0.0625 =0.0775 kef
c. Buoyant earth pressure coefficient (Appendix H):
1 - tan $. cot a
K „ -—— -H__ . 0.40176
1 + tan 4.a tan a
1 +
h'°- 40176 1 + ' 1.350929 O.5103

L-1.350929 - 1 • 1 ^0.0625^
d. Overturning stability analysis (paragraph 4-8) . For the first trial

solution, all of the base is assumed to be in compression (full hydrostatic
pressure is applied at points D and E). For the second trial, full hydrostatic
pressure is assumed to act over the portion of the base which is not in
compression. This procedure is continued until the assumed amount of the base
in compression equals the calculated value. The final solution is shown on the
following page.
N-20
EM 1110-2-2502
29 Sep 89
17.898 KSF
BEARING PRESSURE
2V =161.89*-
XR = 6.030'
207.61 kips x 14.70 3051.87 ft-kips

-45.72 kips x 16.33 -746.61 ft-kips
161.89 kips - ZV
-51.77 kips x 22.08 -1143.081 ft-kips

-24.50 kips x 9.33 -228.59 ft-kips
8.00 kips x 5.33 42.64 ft-kips
-68.27 kips = ZH 976.23 T 161.89 - 6.030 ft = x.
R
N-21
EM 1110-2-2502
29 Sep 89
Width of base in compression - 3^ - 18.09 ft.
Percent in compression - (18'°-j (100) - 60.3Z > 50% required by Table 4.1.
Overturning criterion is satisfied.

e. Sliding stability analysis (paragraph 4-15).
N' - EV - 161.89 kips, T - EH - 68.27 kips
< N' tan (j) + cL [4-12]

FS
Using the minimum required FS of 1.33 as given in Table 4-1 yields
,. .. , 161.89 tan 40" + 2.5(18.09)

68.27 S Y^3
68.27 S 136.14
Sliding criterion is satisfied.

f. Bearing capacity analysis (Chapter 5).
6 ■ tan •' (§) ■ ~-1 (tSS) ■ "•"• «~«•>
e - I - xR - 15 - 6.030 = 8.970 ft
B - B - 2e - 30 - 2(8.970) - 12.060 ft (Figure 5-la)
Y' - 0.0775 kef, D - 6 ft
q - Y'D - 0.0775(6 ft) - 0.465 ksf [5-8a]

o
N-22
a^^^^^sSSa^^'^
EM 1110-2-2502
29 Sep 89
Ccd - 1 + 0.2(B/B) tan (45° + ■§■) t5"Aa]
F a = 1 + 0.2(0.4975)(2.1445) - 1.213
cd
c . € d - 1 + O.KD/B) tan ^45 + |-)- 1.107 [5-4c]
<« - <«* - (> - f»?-(■ - ^ - •"»* ..'
N - 75.31 , N - 64.20 , N - 93.69 (Table 5-1) i

c q y
From Equation 5-2 . . .. . ..... ;.
Q = 12.06o[l.213(0.5564)(2.5X75.31) + 1.107(0.5564X0.465) (64.2)
1.107(0.1834)(12.060)(0.0775)(93.69)1
+ 2
. -I
Q ■ 1861.41 kips
For this problem EV = N' . The FS is calculated using Equation 5-1.
FS = 2- = if6*-4* = 11.50 > 2.0 (Required by Table 4-1.)

N 161.89
Bearing criterion is satisfied.
N-23
EM 1110-2-2502
29 Sep 89
N-3. EXAMPLE 3. Analyze the wall for overturning stability, sliding and
bearing capacity. Determine water pressure using the line
of creep method. Calculate reinforcement required at
critical sections. Case II, design flood.
20*
12' .5' 1.5'.
RIVERSIDE LANDSIDE
11.12'
WT. OF CONCRETE,
WATER A SOIL -■»■^:
ABOVE CDEG—--"
CM
V ■■■.Jl'.-i-[Al.'-'-.l,l..JUll.-.'U4M-^".-!V.'!l.-,'i^.• ■ I | "T
.l~x*.:J)l,n: : ■•»;»•*■•
"b- • "yi «•>•'.•t,.--,-, o-.-.».•-%•"•
S..-.'.»Mi»'-.OAV,.i,.„; ; f* .\:
.,»W,^M.>l
; l
SEEPAGE PATH FOR'

SLIDING AND
OVERTURNING ANAL YSIS
1 F
-^CHECK SLIDING
ON THESE PLANES
'PARA. 7-6. SOIL PROPERTIES: >*SAT = 0.12KCF

ASSUMED C = 0.9KSF. 0 = 0 (UNDRAINED)
CRACK TO 0 = 28" ,C = 0 (DRAINED)
BOTTOM OF
KEY.
N-24
EM 1110-2-2502
2 9 Sep 89
a. Water pressures (line of greep, paragraph 3-19).
L
CG ? V*2 + 2 2
° " 20 40 ft
- » L
BC "-°— Ä
fc-* 9 ft
LGH - 5 ft, Lg - 20.4 ft + 5 ft - 25.4 ft
„ _ Dist. below ^^CG^ /. r 9 x 20.4\

U
G " Headwater " ~T^- \ ' (j4 ft
" 25.4) Q 0625
' " °'4232 ksf
Compute water pressure at D and E. Prorate head loss along path CDEG.' Total
head loss along path
CG=i^.7.228ft
Lg (Concrete surface) = Lc_ + L^ + L.

EG
Lg - 1.5 + 4.03 + 18 - 23.53 ft
Head loss at D - '2\'l3 (7.228) - 0.4608 ft
uD - (18 - 0.4608)0.0625 = 1.0962 ksf
(1,5 03)
Head loss at E - 2^J' (7.228) - 1.699 ft
Ug - (14 - 1.699)0.0625 - 0.7688 ksf
N-25
EM 1110-2-2502
29 Sep 89
b. Overturning stability (paragraph 4-8)

* SOIL FORCE IS
JUST SUFFICIENT
TO MAKE ZH = 0.
SOIL RESISTANCE
ABOVE G IS
NEGLECTED.
5.34"
0.1545
KSF
XV = 12.
2.51" ^X„=7.66'
Overturning calculations
25.37 kips x 11.12 ft 282.11 ft-k

-12.86 kips x 11.39 ft ■146.48 ft-k
EV 12.51 kips
•10.13 kips x 2.00 ft -20.26 ft-k

4.79 kips x -1.28 ft -6.13 ft-k
5.34 kips x -2.00 ft -10.68 ft-k
ZH = 0.00 kip 98.56 * 12.51 = 7.87 ft = xT
One hundred percent of base is in compression satisfying the requirements of

Table 4-2.
N-26
EM 1110-2-2502
29 Sep 89
c. Sliding stability analysis (paragraph 4-10)

(1) On Plane CG:
IV - 25.37+3.99 • 15.48 - 13.88K

IH - 10.13 -4.15 - 5.98K
N' - IV cos tt + IH sin a
T - IH cos a - IV sin a
N* - 13.88 x 0.981 + 5.98 x 0.196
N' - 14.79K
SOIL BELOW T - 5.98 X 0.981 - 13.88 X 0.196
CONCRETE T - 3.15*
*-*f5* '
■ 20.4'
U = 75.48*
For undrained shear strength:
cL 20A
CG * °-9 X
" 18 36 ki 8
- P
< N' tan Q + cL

FS [4-12]
From Table 4-2, the minimum FS is 1.5.
18.36
3.15
1.5
3.15 £ 12.24
N-27
EM 1110-2-2502
29 Sep 89
For drained shear strength,
N' tan <f> - 14.79 * 0.532 - 7.86 kips
< N' tan i» + cL

FS [4-12]
3.15 S7-^-
3.15 i 5.24
Sliding resistance is adequate without considering soil resistance on landside.
(2) On Plane CF:
Ls = LCF + LFH = 20' + 9' = 29'

25.37*
UF = [l8- 1o(||)]. 0.0625 =0.7377 KSF
10. 13*
i i
<b
'' c
0.7371
KSF
U = 18.6&
N-28
EM 1110-2-2502
29 Sep 89
Y' - effective weight on landside - [9 ft(0.12) - 0.7371] * 9

- 0.0381 kef
Undrained condition,
c = 0.9 ksf
c, = SMF(c) [3-10]
d
c, - | (0.9) = 0.6 ksf

Q 1
K =1.0 (from Equation 3-4)
The at-rest earth force may be calculated as:
PR = \ Yfeh2 = i (0.0381)(9)2 - 1.54 kips
cdLCF = 0.6(20) = 12 kips
N ta
T S ' gs6 + CL
[4-12]
T - EH = 6.82 - 1.54 - 5.28 kips
12
5 28
' =I3
5.28 S 8
Sliding resistance is adequate.
Brained condition,
N-29
EM 1110-2-2502
29 Sep 89
<f> - 28°
tan <(>. ,
SMF - -* = 4 [3-10]
tan $ 3
1
$. - tan (| tan <H - 19.52°
Kp - tan2(45° |) «- 2.77
/A5° + *} 2.:
Let K - 1/2 K - 1.385 (Paragraph 3-8b)
Ky h2 =
P
R ' i b I d-385^0-0381)^2 - 2-14 kl s
P
N' - ZV « 25.37 + 8.76 - 18.62 = 15.51
T <= 10.13 - 3.31 - 2.14 - 4.68 kips
T s N' tan d> + cL [4-12]

FS
. ,_ <. 15.51 _
4.68 tan 28"
4.68 £ 5.50
Sliding resistance is adequate.
d. Bearing capacity analysis (on Plane CG).
N' - 14.79 kips
N-30
EM 1110-2-2502
29 Sep 89
T = 3.15 kips
a = 11.31° - 0.197 rad
L
CG 20.4
e = ~Y~ - a = ^f- - 7.79 = 2.41
B = LCG - 2e - 15.58 ft
6 = tan-1 = tan_1
(¥) (TITTI) " 12'02° <F18ure 5-1)
Y* = 0.120 - 0.0625 = 0.0575 kef
D = 5 ft
qo = Y'D = 0.0575(5) •= 0.2875 ksf [5-8a]
5 +
cd<* = 0) = 1 0.2^ =1 + 0.2 (j^) = 1.064 [5-4a]
C C = l (f r =
qd " Yd ° * °0) t5"4b]
e
qd " C
Yd
= l +
°a(-) tan
(45° +
I) (for
♦ = 280) [5_4c]
? = = 1 +
qd Sd °-1(l5T58)C1-6643) = K 53
° (
* " 280)
*qi ■ *ci " 0 " to/ - 0 - ^)2 - 0.7507 [5-5.]
2
C
Yi " I " **W) ' °'3257
1
t5-5b]
N-31
EM 1110-2-2502
29 Sep 89
C • f - (1 - a tan »)2 ■ (1 - 0.197 x 0.532)2 - 0.8015 [5-6a]

*qt Yt
«..-'- (ÄT) ■ > - (%&)" °-'232 <f

" ♦ ■0) [5 6b
- '
Undrained condition:
c - 0.9 ksf
From Equation 5-2
* • f(5cd?ci5CtCNC +
«,d«qt Wl)
N c - 5.14 , Nq - 1.00 (Table 5-1)
Q - 15.58[l.064(0.7507)(0.9232)(5.14)(0.9) + 1(0.7507) (0.8015) (0.2875) (1)]
Qr- 55.84 kips, FS - |r - firff ° 3'78 * 3'00 (Table 4_2)
Drained condition:
* - 28°
Q - B r r r q H + Td W Y Y
N - 14.72 , N - 11.19 (Table 5-1)

q Y
Q - 15.58 1.053(0.7507)(0.8015)(0.2875)(14.72)
1.053(0.3257)(0.8015)(15.58)(0.0575)(11.19)1
+ 63.24 kips
2 J
N-32
&3&âf^&n$g8®*&gg**%&gi>l
EM 1110-2-2502
29 Sep 89
FS
* ^" fol" 4-28 > 3-00 (Table 4_1
>
Bearing capacity is adequate.
e. Reinforcement (Chapter 9).
f'c - 3 ksi, f y - 40 ksi, cover - 4.5 in.
(1) At base of stem:
M = 4.5 x 4 - 18.00 k-ft

r i
M
u 1.9(18.00)12 ,,,„.,
1 . 0.0625 1 ♦ o 456 k-in
-° -
d = 24 in. - 4.5 in. - 19.5 in.,
in
b = 12 in.
4.S« 1 »* ii
b' i1 /
ltd
k = 1 -
L
/l
V»
- T (Figure 9-2)
' / I *t '' u */
\ '"E'bd2
0.425f'l
c
0.75
KSF
tn -1 - ^r 5817.825
456.0
0.0400
C T =
u " u °-85fckubd - 0.85(3)(0.040)(12)(19.5) = 23.87 kips
A
s fy m— °-60 ln
- /ft
Check ductility requirements:
ß. = 0.85 , E - 0.003
l c
0.85f
p
b --f-^ll (see example 1, paragraph i)
e +
m 29,000 ksi>
N-33
EM 1110-2-2502
29 Sep 89
yu.uuj + 29t000y
p Xp X 0,2S
max ' b » * (ParaSraPh 9-8c(2)(a))
p
max * °-25(0.03712 " 0.000928
Pmln - 200/f = 200/40,000 ksi = 0.005 (paragraph 9-8b(4), from ACI 318)
p
■ ra ° nfror= °-002564
p < p
min
Instead of using p , ACI 318 allows the minimum area of reinforcement to be

one-third greater than that required by analysis. Therefore,
As - 4/3(0.60) - 0.80in.2/ft
p
" k - T2Ttf?5T - °-00342
p m p
max
(2) Check shear at distance d above base (paragraph 9-8f)
d
v ■d - (ir)dv ■19-5 - °-0333 dv
d
v ■ 0M3 = 18 87 ln
- - -1-573 ft
N-34
pp|^!|jp!?p^5^v
EM 1110-2-2502
29 Sep 89
V = 1 (0.0625X12 - 1.573)2 - 3.40 kips
Vu - 1.9 V - 1.9(3.40) = 6.46 kips = 6,460 lb
*VC =
*2^ bdv (from ACI-318)
*Vc = 2(0.85)(/3ÖÖÖ)(12)(18.87) = 21,084 lb > 6,460
Shear capacity is adequate. Shear is most critical for stem.
(3) Toe at face of stem (Figure 9-2):
8.62 x 3.06 = 26.38

-3.92 x 2.99 = -11.72
Z99- ■3.9t"<S0lL + C0NC) Vj - 4.70 kips M = 14.66 k-ft
b - 12 in., d - 19.5 in.
3.06' G 0.425fM>d2 = 5817.825
8.62K JÜ = 1.9(14.66)(12)
* 0.9 371.39 k-in.
BRG. PRESS
+ UPLIFT ku - 1 - ^Z 371.39
5817.825 0.03244
Cu = Tu = 0.85(3)(0.03244)(12)(19.5) - 19.36 kips
, , _u = 19.36
s fy " 40 0.48 in. /ft
Check ductility:
0.00928 , p - 0.005
s 0.48
P = =
" bd 12(19.5) °-00205
N-35
EM 1110-2-2502
29 Sep 89
Again, since p < p^ , use a one-third increase in the area of reinforcement

required by analysis. Therefore,
A - 4/3(0.48) - 0.64 in.2/ft
p =
" bi T2TTOT " °-002735
p < p_
(4) Heel and key reinforcement:
14.67 x 6.00 = 88.02

SOIL * WATER * CONC. ~-14.67*
1.05 x 11.10 = 11.66
-8.86 x 6.63 = -58.74
-5.25 * 4.71 = -24.73
1.61 kips
-3.73 x 3.12 = -11.64

3.7&
-5.34 x 3.00 = -16.02
1.63 x 0.02 - 0.03
4.00 x 3.O8 = 12.32
-3.44 kips
M -0.90 k-ft
0.7200
KSF
b = 12 in., h = 24 in., d - 19.5 in.
S.25* 0.425f*bd*
c = 5817.825
Reinforcement at "0" with 5.34 kips force on key (Figure 9-4):
M 1,M =
u * o 1.9(0.90)(12) - 20.52 in.-k
Pu = 1.9P = 1.9(3.44) = 6.54 kips (tension)
ji _ 20.52
Pu 6.54 3.14
N-36
EM 1110-2-2502
29 Sep 89
d - | = 19.5 - — = 7.5
M
u d h
p~ * ~ 2 Therefore, the conditions of Figure 9-5 apply.
u
Mue « -Mu + Pu (d
\ - £)
2/
= -20.52 + 6.54(7.5)
= 28.53 in.-k
Mtie 9ft S^ 9
A = = =
s *f (d - d') 0.9(40)(19.5 - 4.5) °'053 in
- /ft
P , ,,
f A
"? - y s 0^ - 40<°-053> 2
A 7
s - f - ~ 40 °'13 in
« /ft
y
Reinforcement at "0" neglecting 5.34 kips force on key (Figure 9-3)
MQ = 0.90 + 5.34(3.00) = 16.92 ft-k - 203.04 in.-k
Mu = 1.9Mo = 385.78 in.-k
P = 1.9 kips (compression)
Pu = 1.9P = 1.9(1.9) = 3.61 kips
0,9 (0 2)
" 0.1(3)(12)(19.5) '
= 0.89
N-37
EM 1110-2-2502
29 Sep 89
M =M+P|c!-Jj-\
ue u uI 2)
- 385.78 + 3.611
= 412.86 in.-k
M
k
U
- 1 -
I
v
/ 1
<f>0.425f*bd2
c
412.86
^ 89(5817.825)
- 0.04070
0.85f'k bd - .-
As Hfy L
3.61
0.85(3)(0.04070)(12)(19.5)
0.89
40
0.51 in.2ft
Check ductility:
p - 0.00928 , p . - 0.005
max min
p
" bf - T2TI9T5T " °-00218
N-38
EM 1110-2-2502
29 Sep 89
p < p
min
Use Ag = 4/3(0.51) - 0.68 in.2/ft
p = =
bf 12(i985) = °-00291
p < o
Reinforcement in key at "E" (Figure 9-2):
M = 5.34(2) + 3.73(2.12) - 4.00(2.08) = 10.27 ft-k
S = 1.9(10.27)(12)
Q^
_
- 260.11 k-in.
k l
u " " V1 - 581?:825 - °'02261
C T
u = u = 0.85(3)(0.02261)(12)(19.5) = 13.49 kips
Check ductility:
Pmax - °-00928 • Pmln " °-005
P - bf =
12U9?5) " °-00145
N-39
EM 1110-2-2502
29 Sep 89
a
w < a
M
min
Use A - 4/3(0.34) - 0.45 in.2/ft
p
- n ■ 12TTOT ■ °-oom
p < p
max
N-40
EM 1110-2-2502
29 Sep 89
N-4. EXAMPLE 4. Analyze the wall for overturning, sliding and bearing
capacity. Use the line of creep method to determine water
pressures. Load Case II, Design Flood. Calculate
reinforcement at critical sections.
ysAT=0.12KCF
0=0
c=0.9KSF
a. Water pressures (paragraph 3-19)
uc - 17(0.0625) = 1.0625 ksf
L - 10 ft
n
L_ - 16.49 ft
CD
L„„ - 3 ft
DE
N-41
EM 1110-2-2502
2 9 Sep 89
= L + = 19 49 ft
'S CD SE '
UD - (l3 - 1°19.49,A9)o-0625 = 0.2837 ksf
b. Overturning stability.
0.0625
OIL RESISTANCE
ABOVE D IS
NEGLECTED
10.77'
19.17 * 9.35 - 179.24 N' = EV cos a + ZH sin a

•10.77 x 9.54 * -102.75 T = EH cos a - IV sin a
8.40 kips - IV N' = 8.40(0.970) + 5.91(0.243)
N' = 9.58 kips
-9.03 * 1.67 - -15.08 T = 5.91(0.97) - 8.40(0.243)
3.12 * -1.92 = -5.99 T = 3.69 kips
-5.91 kips 55.42 k-ft -
*D
*->.*»-,* *>*-«!*...-«
One hundred percent of Surface CD is in compression (Table 4-2). Overturning

criterion is satisfied.
N-42
EM 1110-2-2502
29 Sep 89
c. Sliding stability (paragraph 4-15).

On Surface CD:
N' = 9.58 kips, T - 3.69 kips, o = 14.04°, * = 0 , c - 0.9 ksf
LCD = 16.49 ft
T <£
T N' tan j> + cL
$f [4_12]
Using the minimum required FS of 1.5, as given in Table 4-2, yields
3 69 < 9.58 tan 0° + 0.9(16.49)

1.5
3.69 £ 9.89
d. Bearing capacity analysis.
a = 14.04°
« - 0.245 rad
.-«.-'(ir)-^ fcg -H.07
L
CD 16.49
e - — ~ \ = —i 5.78 - 2.465 ft
B = L 2e = 16 49
CD ~ ' - 2(2.465) = 11.56 ft (Figure 5-lb)
Y = Y Y
' sat " w " °'120 " °-0625 " 0.0575 kef
N-43
EM 1110-2-2502
29 Sep 89
q = Y =
o D °-0575(3) =
0.1725 ksf [5-8a]
5
cd-1+0-2(|)-1 + 0
-4l^)=1'05 [5-4a]
?
yd " ?
qd * l
-*> [5-4b]
[5-5a]
«ci-^-^-^^1-^)2-0-587
K [5-5b]
y±-°
5 = ? = 1 [5-6a]
qt yt
-, t 2a
r«««■'-(^■'-(H^ 1
)-»-»« [5-6b]
N, « 5.14 , N = 1 , N =0 (Table 5-1)
?Y8 " 5?qg = 1

qK=[L] -
tan (ß) 2 = 1
] t " tan
(°>]2 " l [5-7a]
r = iX 2(ß), - , 2(0) _ [5-7b]

^cg ~ (ir + 2) " l " (» + 2) l
Q = B (5
cd«el5ct«eg«*«* +
«qd^qtVoV
+ ^YdVnSs!!V [5-2]
2
{(!.(
= 11.56 (1.05)(0.587)(0.905)(1)(0.9)(5.14)
+ (1)(0.587)(1)(1)(0.1725)(1)
+ (1)(0)(1)(1)(11.56)(0.0575)(0)
= 31.00 kips
N-44
iiipiPiff - rr' ? :^f fw^^îä^ffiS ä'Wv«^^""v"r -T'f* ?
EM 1110-2-2502
29 Sep 89
FS 3<24
" ST "T38 " [5-1]
3.24 > 3.0 , so bearing criterion is satisfied (Table 4-2)
e. Reinforcement (Chapter 9).
fg " 3 ksi, f = 40 ksi, load factor = 1.9 , ♦ - 0.9 ,

cover =4.5 in.
(1) At base of stem (Figure 9-2): b - 12 in., h « 23.44 in.,

d = 23.44 - 4.5 = 18.94 in.
M - 0.0625(11.5)
i^)M
M - 0.0625(11.5)3 | - 15.84 ft-k
M
_u=1.9(15.84)(12).A0128k_in>
0.425f'bdi ■= 5488.471
c
K -1 - i] 401.28
5488.471
0.03725
C = T = 0.85f'k bd
u u c u
Cu = Tu - 21.59 kips
. u 21.59 n ,. . 2,.k
A
s " f 4Ö~ * °-54 ln
- /ft
For shear check see Example 1 and 3, Appendix N.
Check ductility and concrete section strength: calculate p. for

b
e - 0.003 , f - 40 ksi, f = 3 ksi, 8, - 0.85 .
*■ y c i
N-45
EM 1110-2-2502
29 Sep 89
p
°-85fcßl / E
c
b " f f—I—+~f j (See Example 1 for derivation of p.)
29,000 ksi
0.85(3)(0.85) / 0.003
40 40
0.003+
29,oooy
0.03712
P
max " °'25 pb " °-00928
pmin " 200/f

y " 200/40,000 - 0.005 (paragraph 9-8b(4), from ACI 318)
0,54
"actual bd 12(18.94) 0.00238
Since p < pmin , use a one-third increase in the required area of

reinforcement (from ACI 318).
As = 4/3(0.54) - 0.72 in.2/ft
A
s
m —*. m 0.72
p bd 12(18.94) - 0.00317
p < P max
(2) In toe at stem (Chapter 9, Figure 9-3): b - 12 in., d - 36 - 4.5

»31.5 in.
N-46
■i
EM 1110-2-2502
29 Sep 89
SOIL + WAT£R*CONC.
0.1419
0.283T
KSF
0.5758
KSF
2.58"
2.58(2.66) = 6.863
5.61(2.95) = 16.550
-3.11(2.96) = -9.206
0.96(-0.34) = -0.326
Mo = 13.881 k-ft
P o - 0.96 + 5.61 sin 14.04° = 2.32 kips
Mu = 1.9(13.881) = 26.37 ft-k = 316.44 in.-k
Pu - 1.9(2.32) - 4.41 kips
M = M + P
ue u u(d " l) = 316 44 +
' 4.41(31.5 - 2|J- 375.98 in.-k
M
_ue _ 375.98
<f> 0.9 = 417.75 in.-k
0.425fM>d2 = 0.425(3)(12)(31.5)2 - 15,181.425
N-47
EM 1110-2-2502
29 Sep 89
k - 1 - 1 - ifi L_ . ! . A . 417,75
u
V n.A^f^2
* 0.425f'bd V
* 15,181.«
15,181.425
c
- 0.01385
Cu - 0.85rkubd - 0.85(3) (0.01385) (12) (31.5)
Cu - 13.35 kips - Tu
A
s" ry - ii¥^" °-33 in-2/ft
p
- nrtor" °-000873 * pmax - °-00928
Since p < p mxn , use a one-third increase in the area of reinforcement (from
ACI 318).
A8 - 4/3(0.33) - 0.44 in.2/ft
N-48
EM 1110-2-2502
29 Sep 89
(3) In heel at stem (Figure 9-3)
11.ieP(S0IL + WATER + CONC.)
4.11'
0.8115
0.8731
1.74*
WATER
«.«4"
-1 .74 X 2 .07 as -3 60
11 .18 X 4 .11 ■ 45 .95 b - 12 in., d - 19.5 in.
3 .75 X 1 .09 = 4 .09
-2 .643 X 3 .26 - -8 .62 0.425f*b<T - 5817.825
c
-6 .94 X 4 .30 - -29 .84
M ■ 7 .98 k-■ft
M - 1.9(7.98) - 15.16 ft-k - 181.92 in.-k
P - 3.75 - 1.74 - 2.643 sin 14.04° - 1.37 kips (compression)
P - 1.9(1.37) - 2.60 kips
M - M + P (d - %) - 181.92 + 2.60(l9.5 - ^4) - 201.42 in.-k

ue u u\ 2/ \ 2/
N-49
EM 1110-2-2502
29 Sep 89
" °'9 " OFbh

c
(0 2
' >
0,9 (0,2)
" 0.1(3)(12)(24)
- 0.89
ûe . 201.42 226 31 in _k

Ü OF - -
Check dmin from Equation 9-13:
p
™ av
max
=
°'25pi,
b - 0.00928
k _ fyPmax _ 40,000(0.00928) „,,--,

k
m " ÖT85F 0.85(3000) " °'U557
M
u
min
0:85fMcmb(l-^f)
226.31
0.85(3)(0.14557)(12)(l - °-^557)
7.40 in.
This is an approximate value of dmin because Equation 9-13 is valid only for
flexure.
hmin ' 7,4

° + 4 5
' " 11,9 in
*
N-50
F—■
EM 1110-2-2502
29 Sep 89
The heel could have a constant thickness of 12 inches if desired. The steel
will be sized for a d = 19.5 inches.
L ue
k = 1 -
U 1
^ (f»0.425f'bd2
c
- 1 - Ji »i-!L
5817.825
0.01964
P
0.85f'k bd - -r
A. c u 9
S f
0.85(3)(0.01964)(12)(19.5) - %j$
40
0.22 in.2/ft
p
■ bi - nriüsT"°-0009402 < p
mm * °-005
Since p < p J , use a one-third increase in the area of reinforcement,

min
A = 4/3(0.22) = - 0.29 in.2/ft

s
N-51
EM 1110-2-2502
29 Sep 89
capacity. Determine water pressure using the line of creep
method. Load Case 12.
Assume that sheet pile cutoff wall is 50 percent effective.
W as'i.
—
SOIL * WA TER * COHC. - 2*62*
** ,1 I,
'•* 10.1V
SOIL PROPERTIES: ySAT - 0.12S KCF

0 = 20*
c = 0.4 KSF
-SHEET PILING
SEE PARAGRAPH 7-As REGARDING PENETRA TION OF
IMPERVIOUS STRATUM BELOW PERVIOUS SOIL
£ IMPERVIOUS STRATUM
a. Water pressure with steel sheet pile cutoff wall. Reference:

Paragraph 7-4a.
Full-head pressure on headwater side of sheet pile at point C
= (18 ft) (0.0625 pcf) = 1.125 ksf
Pressure at point F, based on seepage path from cutoff wall (point D) to
point G:
N-52
EM 1110-2-2502
29 Sep 89
(pressure \
head at F + total head differential * ||g) (0.0625)
due to position /
= (ö.O + 12.0 2P25")(0-°625) = 0.516 ksf at point F
Pressure on tailwater side of sheet pile at point D
= full-head pressure at D - 50% (full-head pressure at D - pressure at

point F)
= 1.125 - 0.5(1.125 - 0.516) = 0.821 ksf
b. Lateral soil force. Resisting side:
Y' = 2 ft(weight of water) + 4(weight of saturated earth)
- Seepage at F I * 4
= 2(0.0625) + 4(0.125) - 0.5161 * 4
= 0.0273 kef average, point G to point F
KQ = 1 - sin <f> = 1 - 0.342 - 0.658 [3-4]
2
P O = i/ K O Y.h
D
- iZ (0.658)(0.0273)(4)2 » 0.1437 kips
r
N-53
EM 1110-2-2502
29 Sep 89
c. Overturning (paragraph 4-8).
1.44SB KSF
J.V = 12.24"
24.62 x 10.11 - 248.91

-12.38 * 9.85 - -121.94
IV - 12.24 kips
-10.13 x 6.00 » -60.78

0.14 * 1.33 - 0.19
1.41 x 1.87 = 2.64
IH - -8.57 kips 69.02 * 12.24 - 5.64 ft - ^
a - 3^ = 3(5.64) = 16.92 ft < 18.00 ft - b
Percent of base
in compression
YgVlOO) = f^jl^jlOO - 94% > 75% (Table 4-2)
Criterion is satisfied.
d. Sliding stability (FS »1.33 required by Table 4-2, paragraph 4-15)
N' IV - 12.24 kips, T * IH - 8.58 kips
N-54
EM 1110-2-2502
29 Sep 89
tm + CL
T * *' g* [4-12]
Using the minimum required FS of 1.33 from Table 4-2 yields
0 _fi < 12.24 tan 20° + 0.4(16.92)

8.58 F733
8.58 * 11.22
e. Bearing capacity (Chapter 5),
« - tan'M ||\- tan"1 (jf^f) - 35.03° (Figure 5-1)
e=|-xR=^|- 5.64 - 3.36 ft
B = B - 2e = 18 - 2(3.36) - 11.28 ft
Y' = Y, = 0.125 - 0.0625 = 0.0625 , D = 4 ft
q = Y'D = 0.0625(4) - 0.25 ksf [5-8a]
Kcd = 1 + O.2J3J tan (45° +£)= 1 + 0.2(^-7^)

(«'+$)- 0.2^) (1.428)
(l.< = 1.101 [5-4a]
\B /
C
qd =
Sd = X + 0.lgtan(45+|)
°-
= 1 + O.lf-rr^)
OA
(TT2S)
(1.428) = 1.051 [5-4c]
N-55
EM 1110-2-2502
29 Sep 89
*qi " ?ci k-hJ-{-Wf->- 373 [5-5a]
eyl - o , ö > + [5-5b]
C
Y8 - € [l - tan
qg I1 "
(6)12 - [l - tan
tan (6) tan (0)1
(0) - 1 [5-7a]
1 - 1 .
*cg s
qg N tan 4> 14.83 (tan 20°) " l [5-7d]
c
Cqt - Cyt - (1 - a tan <fr)2 - (1 - 0)2 = 1 [5-6a]
1 - C qt . 1 - 1 .
*ct " 5
qt
J
N tan ♦ - 1 - , , „» ,. STS7TT
14.83 (tan 20°)
- 1 [5-6c]
■ c
Nc «= 14.83 , N - 6.40 , Ny * 2.87 (Table 5-1)
Q - B +
^cd^ctWV «qdWoAV
qdsqisqtsqgHo q'
, (WV^ [5-2]
- U.28[(1.101)(O.373)(l)(l)(0.4)(14.83)
+ 1.051(0.373)(1)(1)(0.25)(6.4)
+ 1.051(0)(1)(1)(11.28)(0.0625)(2.87) (1/2)1 34.55 kips
N' - 12.24 (EV for this problem)
FS
"^-fof-2-82>2 [5-1]
Bearing criterion is satisfied (Table 4-2)
N-56
EM 1110-2-2502
2 9 Sep 89
capacity. Use the line of creep method to determine water
pressures. Load Case II, design flood.
saw
J.5'
SOIL PROPERTIES: ygAT = 0.125 KCF
♦ = 20°
c = 0.4 KSF
N-57
EM 1110-2-2502
29 Sep 89
a. Water pressures (paragraph 3-19),
LCF - -yp8.5)2 + (17.5)2 •= 42.29 ft, LfQ « 5 ft, Ah = 22 ft
Ls » LCF + LFG = 42.29 + 5 - 47.29 ft
uc - 44.5 (0.0625) - 2.7813 ksf
22
uF - (27 ft - 47 29>29) °'0625 " °*4579 ksf
Compute water pressure at D and E. Prorate head loss along path CDEF.
Head loss along path CF - Jj^| (22) = 19.674 ft
L_ (concrete surface) = L— + LD£ + L EF
L_ = 1.5 + 10.19 ft + 36.27 ft = 47.96 ft
Head loss at D = ^|^ (19.674) - 0.6153 ft
(44.5 - 0.6153)0.0625 - 2.743 ksf

"D
(1 5
Head loss at E = - ^ ^'I9) (19.674) = 4.795 ft
uB - (34.42 - 4.795)0.0625 = 1.852 ksf
b. Lateral soil force (resisting side, above point F).
K - 1 - sin 4 - 1 - 0.342 - 0.658 [3-4]

o
Y' - 15 (0.125) - 0.4579] * 5 - 0.0334 kef
P - 4 K Yvh2 - 4 (0.658) (0.0334) (5)2 - 0.275 kips

O I O D I
N-58
EM 1110-2-2502
29 Sep 89
c. Lateral water force (driving side)
h = 22.00 + 22.50 = 44.5 ft, y„ = 0.0625 ksf
P„ = i. y„h2 = i. (0.0625) (44.5)2 = 61.88 kips
d. Overturning stability (paragraph 4-8, Figure 4-6)
3M1*
87.21 x 24.20 2110.48

-48.59 x 23.78 -1155.47 b
38.62 x ZV R _ 536.88
38.52
= 13 go ft >
7
-61.88 x -2.67 165.22
0.275 x 1.67 0.45
28.74 x -8.75 -251.48
32.87 x -10.11 -332.32
0 ZH ML 536.88 k-ft
100 percent of base is in compression, overturning criteria satisified

(Table 4-2).
N-59
EM 1110-2-2502
29 Sep 89
e. Sliding stability (on Plane CF, paragraph 4-15) .
V^-0.457»
S2.S5*
N' = IV cos o + ZH sin a

T = EH cos a - EV sin a
N' - 44.63 (0.9104) + 32.13 (0.4137) 53.92 kips
T - 32.13 (0.9104) - 44.63 (0.4137) 10.79 kips
L - 42.29 ft
For sliding stability to be satisfied
N' tan <|> + cL [4-12]

FS
L - L
CF
N' tan + + cL._ = 53.92 (0.364) + 0.4 (42.29) - 36.54 kips
N-60
sSsP
EM 1110-2-2502
29 Sep 89
From Table 4-2, the minimum FS required is 1.5.
36 5
T <
=
- *
1.5
10.79 S 24.36
Criterion is satisfied.
f. Bearing capacity (Chapter 5).
o - 24.44°, 6 = tan"1 (|T) - tan"1 {j^lfi) - 11.32° (Figure 5-1]
a - 0.427 rad
L
CF 42.29 ., ,c , ,._
e - -^ a - —£ 17.65 - 3.495
B - LCF - 2e = 42.29 - 2 (3.495) - 35.30 ft
0 - 5 ft, Y.D - 0.0625 , q ob

- y. D = 0.3125 ksf [5-8a]
5cd - 1 + 0.2^ tan ^45 + |) = 1 + 0.2^|-^^ (1.428) = 1.04 [5-4a]
5
qd = Sd " 1 +
°-1(?) tan (45 + I) = 1(02 [5 4c]
"
5 - S - (1 - a tan <>)2 - (1 - 0.427 * 0.364)2 - 0.7133 [5-6a]
C
ct - «,t " ift!?* - °-7133 " 14.83°x7i?364 ' °'66 [5 6cl
"
N-61
EM 1110-2-2502
29 Sep 89
«,i ■ hi " 0 " lö)2 " (l - Wf - °-764 l5 5>1

-
Nc - 14.83 , N - 6.40 , N - 2.87 (Table 5-1)
From Equation 5-2
Q ■ S(jcd*ci«ctcNc +
VqiVo\ +
îV^Tj [5-2]
i.3|l.04(0.;
Q - 35.3 1.04(0.764)(0.66)(0.4)(14.83) + 1.02(0.764)(0.7133)(0.3125)(6.4)
. 1.02(0.188)(0.7133)(35.3)(0.0625)i
LßsSZl] - 164.34 kips
lf>
FS - |r = £'\\ - 3.05 > 3.00 (Table 4-2)
N-62
I^sg!?^/::^:"^-* ■'-'• ■
EM 1110-2-2502
29 Sep 89
capacity. Load Case C2b, breaking wave condition.
SOIL PROPERTIES: ySAT = 0.125 KCF

0 = 0°
C = 0.90 KSF
WATER: yw = 0.064 KCF
a. Water pressures (paragraphs 3-19 and 3-24d,f). Seepage from still

water level (swl) (paragraph 3-24f):
LCD = 22 ft, LDE = 7.0 ft, Lg = 22 + 7 - 29 ft
u_ - 3.7(0.064) - 0.237 ksf
uc = 10.7(0.064) - 0.685 ksf
3/
Up - 10.7 - 2922^ 0.064 - 0.505 ksf (on line of creep)
u ■ 0.0 (end creep, tail water)
N-63
EM 1110-2-2502
29 Sep 89
Wave force (paragraph 3-24): Increase in static force, due to wave crest,
above point C:
j (6.5 + 7.0)2(0.064) - | (3.7 + 7.0)2(0.064) - 5.832 - 3.664 = 2.168 kips
5.832(13.5) | - 3.664(10.7) j - 13.176 ft-k
2.168 k/LF acting at ^4H - 6.077 ft above point C.
The dynamic force of the breaking wave is calculated from procedures found in
Chapter 7 of the Shore Protection Manual.
Dynamic force of breaking wave ■ 5.176 kips at swl
b. Soil force (resisting side).
K - 1.00 (at-rest)
Y' ■ Ysat ~ seepage uplift
Y' - [7(0.125) - 0.505] * 7 = 0.0529 kef
P K Y h2
o " I o b " I (1'0°)(°-0529)(7)2 * 1.296 kips
c. Overturning (paragraph 4-8). Initially, all of the base is assumed

to be in compression. Full hydrostatic uplift is applied to any part of the
base not in compression. The percent of the base in compression is recomputed
until the assumed value equals the computed one. The final solution is shown
below.
N-64
EM 1110-2-2502
29 Sep 89
TOP OF WAVE
WAVE
FORCE
TV = 1B.25?
28.61 x 11.39 - 325.87

-13.36 x 11.60 - -154.98
£V = 15.25 kips
-5.176 x 10.700 - -55.38

-2.168 x 6.077 - -13.18
-3.665 x 3.567 - -13.07
1.77 x 2.333 - 4.12
1.296 x 2.333 = 3.02
EH - -7.943 kips 96.40 15.25 = 6.32 ft = Xj^
3x
R ■= 3(6.32) » 18.96 ft
Percent of base
(fJlOO - (^%p)l00 = 86.18% > 60% (Table 4-3)
In compression
Overturning criterion is satisfied.
d. Sliding stability (paragraph 4-15),
T N' tan di + cL
FS [4-12]
N-65
p^ ~' ~rr~- . ' ' :
' ~ ~ "'-"--" *■ ": -:■'::■-.~'-~:n^-''??iî^s^,^r
EM 1110-2-2502
29 Sep 89
S» - EV ■= 15.25 kips, T - ZH = 7.94 kips
Using the minimum required FS of 1.25 given in Table 4-3 yields
7 /n < 15.25 tan 0° + 0.9(18.96)

l.W s 1725
7.40 £ 13.65

e. Bearing capacity (Chapter 5),
6 ■ tan 1
(w) -1-»-1 (irfy)"27-50- (Figur. 5-D
e
"i"xR"F'"6*32 = 4 68 ft
*
B - B - 2e = 22 - 2(4.68) = 12.64 ft
Nc - 5.14 , N - 1.00 (Table 5-1)
D - 7 ft, Yfc - Y' - 0.125 - 0.064 - 0.061 kef
qQ - Y'D = 0.061(7) = 0.427 ksf [5-8a]
=imin
?cd i+ 2
■ °' {i)~ °' y^) i+ 2 f5_4ai
Cqd - 1.00 [5-4b]
?
ci - V - I1 " lö)2 " {l ' ^wf " °'482 ^«l
N-66
EM 1110-2-2502
29 Sep 89
From Equation 5-2
Qx - B (t ,C ,cN + K X .q N )
l cd ci c qd qino q /
Q = 12.64 1.111(0.482)(0.9)(5.14) + 1.00(0.482)(0.427)(1.00)
Q - 33.91 kips
Using Equation 5-1 yields
FS = % = |!4T = 2.22 > 1.50 (Table 4-3)
N-67
EM 1110-2-2502
29 Sep 89
APPENDIX O
COMPUTER PROGRAM ABSTRACTS FOR REFERENCED PROGRAMS
0-1. Computer program abstracts included in Appendix 0 are: Bearing Capacity-
Analysis of Shallow Foundations (CBEAR); CFRAG - Seepage Analysis of Confined
Flow Problems by the Method of Fragments; CSLIDE - Sliding Stability Analysis
of Concrete Structures; Seepage Package; UTEXAS2-University of Texas Analysis
of Slopes-Version 2; An Interactive Graphics Three-Dimensional Geometry Pro-
gram; CSTR - Concrete Strength Investigation and Design of Hydraulic Struc-
tures; User's Guide for Concrete Strength Investigation and Design (CASTR) in
Accordance with ACI 318-83.
0-1
EM 1110-2-2502
29 Sep 89
CATEGORY A
CBEAR ELECTRONIC COMPUTER PROGRAM ABSTRACT
TITLE OF PROGRAM Bearing Capacity Analysis of Shallow PROGRAM NO.
Foundations (CBEAR) (10017) 741-F3-R0107
PREPARING AGENCYUS Army Engineer Waterways Experiment Station, Automatic Data
Processing Center. PO Box 631, Vicksburg, MS 39180
AUTHOR(S) DATE PROGRAM COMPLETED STATUS OF PROGRAM
Reed L. Mosher and PHASE STAGE
Michael E. Pace June 1982 FINAL OPER
PURPOSE OF PROGRAM
This program can be used for the analysis of the bearing capacity of shallow
strip, rectangular, square, or circular foundations on one- or two-layer soil
systems. The bearing capacity can be computed considering the effects of
embedment of the foundation, inclination of the foundation base, inclined
loads, a sloping soil surface, eccentric loads in three dimensions, submerged
soil, or surcharge.
B. PROGRAM SPECIFICATIONS
Timesharing FORTRAN Program.
C. METHODS
The bearing capacity of an infinite strip footing is derived based on the

classical theory of plasticity using limit equilibrium analysis. The soil
behavior is assumed to be as follows: (a) Mohr-Coulomb failure criteria gov-
ern; (b) shear strength at any point is independent of strain; (c) elastic
deformations are negligible with respect to plastic deformation; and (d) vol-
ume change due to stress is negligible.
D. EQUIPMENT DETAILS
E. INPUT-OUTPUT
Data is input from a prepared data file in free field format or from the
user's terminal during execution. If the data are input from a terminal the
user may enter data by using key command words or by following a prompting
sequence. Output from the program may be directed to a file or printed at the
user's terminal.
F. ADDITIONAL REMARKS
Program is available through the CORPS on WES DPS/1, CSC H6000 at Macon, GA.
A copy of the program and documentation may be obtained from the Engineering
Computer Programs Library (ECPL), WES, telephone number: commercial
(601) 634-2581 or FTS 542-2581.
WES , JUL"lo 2205 «t'UCEi JN« ronuiiu »mCH ii oiMLcri.
0-3
EM 1110-2-2502
29 Sep 89
CATEGORY A
CFRAG ELECTRONIC COMPUTER PROGRAM ABSTRACT
TITLE OF PROGRAM CFRAG - Seepage Analysis of Confined Flow PROGRAM NO.
Problems by the Method of Fragments (10018) 741-F3-R0108
PREPARING AGENCY US Army Engineer Waterways Experiment Station, Automatic Data
Processing Center, PO Box 631, Vicksburg, MS 39180
AUTHOR(S) Michael E. Pace, Dennis R. DATE PROGRAM COMPLETED STATUS OF PROGRAM
Williams, Thomas F. Wolff, and PHASE STAGE
Reed Mosher October 1983 OP
A. PURPOSE OF PROGRAM
CFRAG is a seepage program designed to analyze groundwater flow using the

method of fragments. The program can be used to compute: (1) seepage through
soil mediums which can be model using fragments; (2) head losses; (3) exit
gradients; and (4) resultant uplift and lateral forces.
The CFRAG program is written in FORTRAN 66. The Corps time-sharing library
file name is 10018.
C. METHODS
The method of fragments is an approximate analytical procedure for computing

groundwater flow. The principle assumptions used in the derivation of this
method are: (1) the flow is confined and of finite depth; (2) Darcy's law is
valid, therefore, laminar flow exists; (3) steady state flow exists; (4) the
soil medium is homogeneous and Isotropie; and (5) equipotential lines at cer-
tain locations of the flow region can be approximated by vertical lines.
O. EQUIPMENT DETAILS
Time-sharing computer (Honeywell level 66, CDC Cyber, or Harris 500),
E. INPUT-OUTPUT
Input - Data may be supplied from a prepared data file or from the user's ter-
minal during execution. If the data are input from the terminal, the user may
enter data by using key command words or by following a prompting sequence.
Output - Provides an echoprint of the input data and results of the analysis.
Computer Programs Library, WES; telephone: (601) 634-2581 or FTS 542-2581.
FORM
WES , JUL, SO 2205 REPLACES ENG FORM 2««» WHIC»- IS OBSOLETE.
0-5
ifî?!^^
EM 1110-2-2502
29 Sep 89
CSLIDE ELECTRONIC COMPUTER PROGRAM ABSTRACT

TITLEOF PROGRAM CSLIDE - Sliding Stability Analysis of PROGRAM NO.
Concrete Structures (X007S) 713-F3-R0075
PREPARING AGENCY US Army Engineer Waterways 'Experiment Statioi Information
Technology Laboratory, PO Box 631, Vicksburg, MS 39180
AUTHOR(S)
DATE PROGRAM COMPLETED STATUS OF PROGRAM
Michael E. Pace and PHASE STAGE
Virginia R. Noddin July 1986 OP
This program was developed to assess the sliding stability of concrete struc-
tures using the limit equilibrium method described in the Engineering Techni-
cal Letter (ETL) 1110-2-256.
CSLIDE is written in FORTRAN 77.
METHODS
The program utilizes the limit equilibrium wedge method described in

ETL 1110-2-256. The program performs an iterative search to find the failure
surface with the minimum factor of safety.
(Continued)
The program is operational on the Honeywell DPS-8 CDC Cyber, and Harris 500
computers in the time-sharing mode. Any ASCII time-sharing terminal may be
used, but if graphics are desired a Tektronix 4014 terminal must be used.
E. INPUT-OUTPUT
Input - Data may be supplied from a prepared data file or from the user's ter-
minal during execution. If the data are input from the terminal, the user may
enter data by using key command words or by following a prompting sequence.
All data are read in free-field format.
Output - An echoprint of the input data and the results of the analysis in
tabular and graphical form may be obtained.
Computer Programs Library (ECPL), WES; telephone: (601) 634-2581 or
FTS 542—2581.
This program is designated X0075 in the CORPS Library.
WES 1 JUL SO 2205 REPLACES ENG FORM 3«S3 WHICH IS OMOLCTC.
0-7
EM 1110-2-2502
29 Sep 89
C. METHODS (Continued)
CSLIDE can compute the factor of safety against sliding considering the
effects of:
a. Multiple soil layers with irregular surfaces.
b. Hater and seepage effects.
c. Applied vertical surcharge loads which include line, strip, triangular,

uniform, and ramp loads.
d. Applied horizontal point loads.
e. Irregular shaped structural geometry with either a horizontal or sloped

base.
£. A percentage of the base of the structure in compression due to over-

turning effects.
£. Single or multiple failure planes.
h. Horizontal and vertical induced loads due to earthquake accelerations.
1. Factors which require the user to predetermine the failure surface.
0-8
EM 1110-2-2502
29 Sep 89
CATEGORY B
FEMSEEP ELECTRONIC COMPUTER PROGRAM ABSTRACT
TITLE OF PROGRAM
PROGRAM NO.
Seepage Package (X8202) 704-F3-R0009
PREPARING AGENCY US Army Engineer Waterways Experiment Station, Information
Technology Laboratory, PO Box 631. Vicksbure. MS 39180
Al iTunDjci I *J^~^r-
PHASE STAGE
Fred T. Tracy January 1983 OP
To (1) interactively generate a finite element (FE) grid, (2) to perform a FEM
seepage analysis, and (3) to plot the results.
The driver runs in timesharing and calls X8200 (704-F3-R0006) for grid genera-
tion, 704-F3-ROOU for seepage analysis, and X8201 (704-F3-R0005) for
post-processing.
C. METHODS
Four-sided isoparametric elements are used primarily in grid generation, the

finite element method is used for the seepage analysis, and flow nets, con-
touring, vector, and number plots are used in the post processing.
O. EQUIPMENT DETAILS
Output is displayed on a storage tube terminal such as the Tektronix 4012 or

4014. The program is operational on Honeywell, CDC, and Harris computers.
E. INPUT-OUTPUT
Input/output is performed using a graphics terminal in the time-sharing

environment.
ADDITIONAL REMARKS
The seepage analysis consists of steady-state solutions to plane or axi-

symmetric, confined or unconfined, and homogeneous or inhomogenous problems.
Documentation may be obtained from the Engineering Computer Programs Library
(ECPL), WES, telephone number: commercial (601) 634-2581 or FTS 542-2581.
WES * JUU «O 4&UJ REPLACES ENG POffM 2S8S WHICH IS OBSOLETE.
0-9
EM 1110-2-2502
29 Sep 89
ELECTRONIC COMPUTER PROGRAM ABSTRACT

TITLEOF PROGRAM UTEXAS2-University of Texas Analysis of PROGRAM NO.
Slopes-Version 2 (10029)
PREPARING AGENCYUS Army Engineer Waterways Experiment Station, Information
Technology Lab and Geotechnical Lab. PO Box 631, Vicksburg. MS 39180-0631.
r
LI rrurtcafei
AUTHOR IS) l iy . _. _
DATE PROGRAM COMPLETED STATUS OF PROGRAM
PHASE STAGE
(See reverse) OP
ÜTEXAS2 is a slope stability program designed to analyze slopes by any of four

methods. The program will calculate the safety factor for either a prescribed
shear surface or for a search of the critical shear surface. Both circular
and non-circular shear surfaces can be evaluated.
The UTEXAS2 program is written In FORTRAN 77. The CORPS time-sharing library
file name is 10029.
METHODS
The four analysis procedures are: Spencer's method, Simplified Bishop's pro-
cedure, Modified Swedish procedure with the Corps' side force assumption, and
Modified Swedish procedure with Lowe and Karafiath's side force assumption.
There are five options for type of shear strength data utilized and six
options for specifying pore pressures. All analysis procedures and major fea-
tures can be run in a single data file.
EQUIPMENT DETAILS
Microcomputer with a least 512K memory, a hard disk, and a math co-processor.
Time-sharing computer (CDC Cyber, or Harris 500) with Tektronix 4014 terminal
or emulator for graphics.
INPUT-OUTPUT
Input - Data is supplied from a prepared data file which allows for free-field
input and requires command words.
Output - Provides an echoprint of the input data and results of the analysis
in an output file divided into a series of tables.
Graphics capability for displaying the input data and the final shear surface
is available. A copy of the program and documentation may be obtained from
the Engineering Computer Programs Library, WES, telephone: (601) 634-2581 or
FTS 542-2581.
"tS i JO(_ B0 2205 «PLACES ENG FORM z««> WHICH is OBSOLETE.
0-11
EM 1110-2-2502
29 Sep 89
AUTHOR(S) (Continued)
Dr. Stephen G. Wright-Univ. of Texas, Austin; POC-Earl Edris, Geotech Lab and
Reed Mosher, Information Tech Lab
0-12
EM 1110-2-2502
29 Sep 89
CATEGORY B
3DSAD ELECTRONIC COMPUTER PROGRAM ABSTRACT
TITLE OF PROGRAM An interactive Graphics Three-Dimensional PROGRAM NO.
Geometry Program (X8100). 713-F3-R0008
PREPARING AGENCY US Army Engineer Waterways Experiment Station, Automatic
Data Processing Center. PO Box 631, Vicksburg. MS 39180
AUTHORIS) DATE PROGRAM COMPLETED STATUS OF PROGRAM
PHASE STAGE
Fred T. Tracy October 1978 OP
Program allows user to describe the geometry of a three dimensional structure,

interactively plot.the described structure, and compute weight and centroid
information for individual pieces or the sum total for the structure. Other
modules of the program apply generalized loading forces and pressures and
perform overturning and sliding analyses.
8. PROGRAM SPECIFICATIONS
FORTRAN, Time-sharing program.
C. METHODS
Use a right handed coordinate system. Solid pieces of the structures may be
described as (1) block - a two-dimensional cross-section extended in the third
direction, (2) an eight node brick element, (3) a cluster of surfaces to form
a solid.
Low speed graphics terminal, Central processor.
E. INPUT-OUTPUT
Input must be by a basic data file with addition and display commands entered.
Output will be displayed directly on the terminal.
Program is available through the CORPS on WES G-635, CSC H600 at Macon, GA,
and Boeing Computer Services.
Reports include: 1. General Geometry Module

2. General Loads Module
^ ^^^^^ 3. General Analyses Module
WES , ;__"„ 2205 ■ C'LICCS CNC FORM III] WHICH IS OHOLITC.
0-13
EM 1110-2-2502
29 Sep 89
CATEGORY B
TITLE OP PROGRAM CSTR
- Concrete Strength Investigation and PROGRAM NO.
Design of Hydraulic Structures
_____ (X0066) 713-F3-R0066
PREPARING AGENCY US Army Engineer Waterways Experiment Station, Automation
Technology Center. P0 Box 631. Vicksburg, MS 39180-0631
AUTHORIS) DATE PROGRAM COMPLETED STATUS OP PROGRAM
C. C. Hamby (LMKED-DS) and PHASE STAGE
W. A. Price III (WESKA-E) September 1984 Operational
To perform investigation or design of concrete beams or columns in accordance

with ETL 1110-2-265 for hydraulic structures.
Written in FORTRAN IV using the Graphics Compatibility System (GCS). The

CORPS time-sharing library file name is X0066.
C. METHODS
Strength analysis for investigation or design of rectangular cross sections of

hydraulic structures subjected to axial load plus uniaxial flexure. Analysis
is based on the rectangular stress block described in ETL 1110-2-265.
D. EQUIPMENT OETAILS
Tektronix 401A terminal, if graphics output is desired, otherwise, any ASCII

time-sharing terminal.
E. INPUT-OUTPUT
Input is from a data file; output is to a Tektronix 4014 graphics terminal or

regular printing terminal.
Computer Programs Library, WES; telephone: (601) 634-2581 or FTS 542-2581.
The User's Guide for this program is WES IR K-84-9.
WES ,::;-. 2205 REPLACES EM6 FORM 2«I1 WHICH I* OBSOLETE.
0-15
EM 1110-2-2502
29 Sep 89

TITLE OF PROGRAM User.s guide for Concrete Strength Investl PROGRAM NO.
yaMnn anH n«»»Hg. n (CASTRO -tn Accordance with ACI 318-83
._ . 713-F3-R0067
PREPARING AGENCY us Army Engineer Waterways Experiment Station, Information
Technology Laboratory. PO Rnv 631. Vlrksburg. MS 39180-0631
C. C. Hamby (LMKED-DS) and PHASE STAGE
W. A. Price III (WESKA-E) October 1985 Operational
To perform investigation or design of concrete beams or columns in accordance

with ACI Code 318 for nonhydraulic structures.
Written in FORTRAN IV using the Graphics Compatibility System (GCS). The

CORPS time-sharing library file name is X0067.
C. METHODS
Strength analysis for investigation or design of rectangular cross sections of

nonhydraulic structures subjected to axial load plus uniaxial flexure. Analy-
sis is based on the rectangular stress block approximation described in Sec-
tion 10.2.7 of ACI 318-83.
Tektronix 4014 terminal, if graphics output is desired, otherwise, any ASCII

time-sharing terminal.
E. INPUT-OUTPUT
Input is from a data file; output is to a Tektronix 4014 graphics terminal or

regular printing terminal.
Input data are prepared the same as for program 713-F3-R0 066, "CSTR-Concrete
Strength Investigation and Design of Hydraulic Structures (X0066)." Differ-
ences between the two programs lie only in the stress block depth and other
parameters. Call WES, (601) 634-2300 or FTS 542-2300 for more information.
WES , :ZTU 2205 RCPUACES ENG FORM 2MJ WHICH IS OBSOt-ETE-
0-17
- :-^m00ffjt
EM 1110-2-2502
29 Sep 89
GLOSSARY
TERMS
Active earth pressure: Minimum horizontal pressure condition which develops

when a wall rotates about its base and away from the backfill 0.001 to
0.003 radian (see paragraphs 3-4a and 3-5, and Figure 3-1).
At-rest earth pressure: Lateral pressure condition when no wall movement

occurs (see paragraphs 3-4c, 3-7, 3-10, and Figure 3-1).
Bond breaker: A coating or sheet of a substance that does not adhere to con-
crete, placed on one monolith in the area where concrete will be placed later,
to maintain separate movement of the two monoliths.
Breaking wave: See "waves."
Broken wave: See "waves."
Buttress: A vertical fin, turned perpendicular to the stem, placed monolithic

with the stem and heel so as to brace the stem into a series of wall slabs
supported at the base and the buttresses.
c_: Symbol for cohesion value (see paragraph 3-5 and Figure 3-8) .
Coastal flood wall: A flood wall that is resisting the effects of the surge
tide and waves accompanying a storm. See paragraphs 4-la and 7-1.
Closed-face structure (Chapter 10): A prefabricated facing system for an al-

ternative type of retaining wall, where the facing has no openings. The joints
between precast panels will form a pattern but vegetation cannot grow through
them. See open-face structure.
Counterfort: Like a buttress, except located over the toe instead of over the
heel. The fin is in tension instead of the compression of the buttress.
Diffraction (of waves): The effect of bending of the direction of propagation

(travel) of a wave crest as it passes by the end of a jetty or through an
opening. Thus the wave pattern spreads outward into the sheltered region
within the barrier's geometric shadow.
Drained phi value: Phi value of a soil, as determined by an S test.
Drained soil tests: Tests in which the confining and shear stresses are ap-
plied so slowly that pore water pressure does not build up. An increase in
applied stress produces an equal increase in effective stress.
Driving force: A force acting to move the wall, usually caused by earth and
water beyond the end of the heel. See paragraph 3-7.
GLOSSARY-1
I . .
EM 1110-2-2502
29 Sep 89
Driving wedge: A wedge of soil which produces a horizontal force (a driving

force) tending to cause instability of a wall. See paragraph 3-7.
Fetch: The area of water in which waves are generated by a wind having a
fairly constant direction and speed. Sometimes used synonymously with "fetch
length," the horizontal distance over which a wind generates waves.
Frequency of a wave: See "waves."
Heel: The heel of a wall is the base slab projection pointing toward the net
driving force.
Kern: The portion of the area under the base such that when the resultant
normal force ("N"' or "V" in the figures in this manual) is inside the kern,
the entire base is in compression contact with the subgrade. When the resul-
tant normal force is located outside the kern, some portion of the base will be
tending to lift off of the subgrade instead of being in compression contact.
For a rectangular base, the edges of the kern will lie at the one-third points
of the base width, as shown in Figure 4-4.
Nonbreaking wave: See "waves."
Open-faced structure (Chapter 10): A prefabricated facing system for an al-

ternative type of retaining wall, where the precast facing units have openings
between or through them. Vegetation, usually evergreen, is then planted so as
to grow through the openings and present a more natural appearance of the
wall's exposed face.
Phi: Angle of internal friction of earth (see Figure 3-1).
Passive earth pressure: Pressure condition that develops when a wall is moved
toward backfill, causing horizontal stresses to increase and shear stresses to
reverse direction (see paragraphs 3-4b and 3-5).
Protected side (of a flood wall or seawall): The side facing the area pro-
tected from flooding.
0 test (of soil): Also known as an unconsolidated undrained or UU test. Both

the confining and shearing stresses are applied so rapidly that the neutral
stress supports all the added load, and there is no change in water content.
R test (of soil): Also known as a consolidated undrained or CU test. The

confining stresses are applied to the soil so slowly that the neutral stress is
not changed and the soil consolidates fully. The shear stress, however, is
applied so quickly that the neutral stress carries all this change, and there
is no further consolidation or change in water content.
Refraction (of a wave): The process by which the direction of movement is

changed for a wave moving in shallow water at an angle to the underwater con-
tours : the part of the wave advancing in shallower water moves more slowly
GLOSSARY-2
§§Jät*!fftK-'-j . ••• ~~ """" : :
■ ■'■'•" ■~-/"e"""ssiwiîB
EM 1110-2-2502
29 Sep 89
than that part still advancing in deeper water, causing the wave crest to bend
toward alignment with the underwater contours.
Resisting force: A force tending to resist movement of a wall. See para-

graph 3 - 8.
Resisting wedge: A wedge of soil which produces a lateral reaction (a resist-

ing force) which tends to resist instability of a wall. See paragraph 3-8.
S test (of soil): Also known as a consolidated drained or CD test. The con-
fining stresses are applied so slowly that the neutral stress does not change.
The soil consolidates with no change in neutral stress.
Seawall: See paragraph l-4a, especially the comparison with a coastal flood
wall. A seawall is usually a gravity structure for the purpose of protecting
the area behind it from the action of tide and waves in front of it, sometimes
with a face shaped to dissipate wave energy.
Shoaling: Point at which the water depth gets more shallow as the wave crest
approaches the shoreline or a wall.
Stem: The vertical wall portion of a cantilever inverted-T wall.
Surge stillwater level: A rise above normal water level on the open coast due
to the action of wind stress on the water surface. Surges resulting from hur-
ricanes also include the rise in level due to atmospheric pressure reduction.
Structural wedge: The structural wedge consists of the structure itself with
any soil and water contained within the boundaries of the structure or over the
base.
Toe: The toe of a wall is the portion of the base slab pointing toward the net
resisting force.
Train, wave: See "waves."
Undrained soil tests: Tests where the pore water pressure is not allowed to
dissipate and the water carries all of the applied stresses.
Unprotected side of a flood wall or seawall: The side of the wall facing the
storm tide and waves, or rising water.
Wall friction: The angle of friction between a soil mass tending to move
parallel along the interface between the soil mass and a wall. See para-
graph 3-14.
Water stop: A strip of material, cast into each of two adjacent concrete
monoliths and spanning the space between them, for the purpose of preventing
the flow of water through the space. Usually made of elastomeric material for
GLOSSARY-3
EM 1110-2-2502
29 Sep 89
civil works structures, but also made of sheet metal. See paragraph 7-13 and
Figure 7-9.
Wave parameter definitions (see paragraph 3-24) are best obtained from Chap-
ter 7 of the Shore Protection Manual (U. S. Army Engineer Waterways Experiment
Station 1984).* Abbreviated definitions are shown below.
Breaking wave: While there are several types of breaking waves, the type
associated with the high-impulse effects used in this manual is the
plunging breaker, where the wave crest becomes more and more steep, until
the crest curls forward and falls over a pocket of trapped air. This is
characterized by a very large dynamic impulse of short (0.2 second, ap-
proximately) duration and a rise in hydrostatic pressure from still water
(no wave) up to the crest one-half of the wave height above still water.
See paragraph 3-24d.
Broken wave: A somewhat confused mass of water surging forward after the
wave has broken some distance away from the wall. See paragraph 3-24e.
Nonbreaking wave: A wave impacting on a wall under conditions where there

is no breaking tendency but the mass of water is stopped from forward mo-
tion by the wall and imparts its energy to the vertical face. See para-
graph 3-24c.
Wave height: The vertical distance from the crest of a wave to the ad-
jacent trough (lowest elevation). A continuously changing value in a
typical train of waves, frequently assumed to have a Gaussian distribu-
tion. See paragraph 3-24b for the assumed values as fractions of the
significant wave height (an average of the highest one-third of all of the
waves in the wave train is assumed for design of the structure).
Wave length: The horizontal distance from one wave crest to the next
crest in the group (train) of waves. A continuously changing value in a
typical train of waves, frequently assumed to have a Gaussian
distribution.
Wave steepness: The ratio of wave height to wave length.
Wave train: A group of waves coming from the same direction over the same
fetch.
Wave frequency: The number of wave crests passing a given point in one
second, the reciprocal of the wave period.
Wave period: The time in seconds required for a wave crest to travel a
distance of one wave length, the reciprocal of the frequency.
* References cited in this appendix may be found in Appendix A, "References.
GLOSSARY-4

USACE - Retaining and Flood Walls

Uploaded by

Copyright:

Available Formats

USACE - Retaining and Flood Walls

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

USACE - Retaining and Flood Walls

Uploaded by

Copyright:

Available Formats

CECW-ED Department of the Army EM 1110-2-2502

U.S. Army Corps of Engineers

RETAINING AND FLOOD WALLS

Distribution Restriction Statement

"V: 29 Sept 1989

ENGINEERING AND DESIGN

Retaining and Flood Walls

Engineer Manual 29 September 1989

Engineering and Design

2. Applicability. This manual applies to all HQUSACE/OCE elements and field

FOR THE COMMANDER:

Albert J. Genetti, Jr.

This manual supersedes EM 1110-2-2501 dated January 1948 and EM 1110-2-2502

Engineer Manual 29 September 1989

Engineering and Design

Subject Paragraph Page

Purpose 1-1 1-1

CHAPTER 2. GENERAL DESIGN CONSIDERATIONS

Section I. Types of Retaining Walls

Subject Paragraph Page

CHAPTER 3. FORCES ON WALLS

CHAPTER 4. STRUCTURE STABILITY

Scope 4-1 4-1

Subject Paraqraph Paqe

Section III. Overturning Stability-

CHAPTER 5. FOUNDATION ANALYSES

Section I. Bearing Capacity of Wall Foundations

CHAPTER 6. DESIGN AND CONSTRUCTION DETAILS AND CAUSES

Foundation Preparation 6-1 6-1

Subject Paragraph Page

CHAPTER 7. SPECIAL CONSIDERATIONS FOR FLOOD WALLS

Section I. General Characteristics

CHAPTER 8. CONCRETE GRAVITY WALLS

General Factors 8-1 8-1

CHAPTER 9. CANTILEVER REINFORCED CONCRETE WALLS

General Characteristics 9-1 9-1

Subject Paraqraph Paqe

Load Cases 9-5 9-1

CHAPTER 10. ALTERNATE TYPES OF RETAINING WALLS

APPENDIX A. REFERENCES A-l

APPENDIX B. BIBLIOGRAPHY B-l

APPENDIX C. NOTATION FOR CHAPTERS 3, 4, and 5 C-l

APPENDIX D. NOTATION FOR CHAPTER 9 D-l

APPENDIX E. COMPARISON OF DANISH CODE AND JAKY EQUATIONS

Subject Paragraph Page

APPENDIX G. DERIVATION OF EQUATIONS FOR CRITICAL SLIP-

APPENDIX H. DERIVATION OF PRESSURE COEFFICIENTS FOR

APPENDIX I. DERIVATION OF EQUATION FOR DEPTH OF CRACK

APPENDIX J. LATERAL PRESSURES DUE TO COMPACTION J-l

APPENDIX K. DERIVATION OF VERTICAL SHEAR FORCE FOR

APPENDIX L. DERIVATION OF GENERAL WEDGE EQUATION FOR

APPENDIX M. LATERAL EARTH PRESSURE COMPUTATIONS,

APPENDIX N. STABILITY, BEARING CAPACITY, AND

APPENDIX 0. COMPUTER PROGRAM ABSTRACTS FOR REFERENCED

2-1 Types of retaining walls 2-2

LIST OF FIGURES (Continued)

3-31 Water pressures from flow net 3-56

LIST OF FIGURES (Continued)

6-8 Vertical check valve at end of longitudinal drain 6-11