WP LOTO Past Present Future
WP LOTO Past Present Future
WP LOTO Past Present Future
Future of Lockout/Tagout
Meaningful connections between the
lessons of the past, standards today
and safer working in the future
More Meaningful Connections
Introduction
Panduit has long and meaningful experience across a diverse range of industries where energy
sources pose a serious risk to workers. We have invested heavily in research and development of
unique Lockout/Tagout solutions that maximize safety, efficiency and compliance. We have also
gained industry leading expertise in regulations, and the trends shaping future practices, which are
explained in this whitepaper.
OSHA’s standard for the Control of Hazardous Energy (Lockout/ Tagout) 29 CFR 1910.147 addresses
one of the most critical safety procedures in general industry – protecting workers during servicing
and maintenance of machines and equipment from unexpected startup or release of stored energy.
Craft workers, electricians, machine operators, and laborers are among the three million workers
who service and maintain equipment routinely and face the greatest risk of injury from energy
sources including electrical, mechanical, hydraulic, pneumatic, chemical, thermal, and other sources
in machines and equipment. Employees in almost every industrial division are exposed to such
hazards, but most lockout/tagout accidents and injuries occur in manufacturing.
The brutality of these tragedies, pulled from OSHA enforcement cases, is reinforced by data collected by the
U.S. Bureau of Labor Statistics (BLS). Analysis of BLS lost-workday data indicates that the severity of injuries
from failing to control hazardous energy sources (an average of 24 lost workdays per incident) is much higher
than the national industry-wide average of 16 lost workdays per incident.
In fact, OSHA has estimated that its lockout/tagout (LOTO) standard prevents 85 percent of the total number
of injuries or fatalities from exposure to hazardous energy in the workplace. It estimated that approximately
31,900 minor (non-lost-workday) injuries, 28,400 lost-workday injuries, and 122 fatalities per year are
prevented by the standard.
Years of Standard-Setting
OSHA’s LOTO standard was a long time in coming. When OSHA first published general industry standards in 1971
(adopting either national consensus standards or existing federal standards), there was no general, all-
encompassing consensus or federal standard for locking out, tagging out, or disabling machinery or equipment
to protect workers when maintenance or servicing duties were performed. OSHA did, though, adopt lockout-
related provisions of consensus standards developed for specific types of equipment, such as powered industrial
trucks, overhead cranes, derricks, woodworking machinery, mechanical power presses, forging machines,
welding, bakery equipment, sawmills, and electrical safety-related work practices.
Since the inception of the OSHA enforcement program in 1971, the agency for the most part had to rely on use
of the “General Duty Clause” (section 5[a][1] of the Occupational Safety and Health Act) citation to ensure that
employers protected their workers. OSHA conceded that this approach met with only limited success because
compliance officers had to prove that the hazard was a “recognized” hazard and that it was causing or could
cause death or serious physical harm
In January, 1977, OSHA published a Notice in the Federal Register, “Machinery and Machine Guarding,
Request for Information on Technical Issues and Notice of Public Meetings.” OSHA asked if lockout should
always be required when machinery is not in its normal operating mode, or whether alternative methods,
such as tagout, should be permitted. Respondents to the Notice generally recognized the hazards to
employees when maintenance and repair work was being done, and the need to lockout or tagout to control
these dangers. Opinions varied widely, though, on whether a lock, tag, or combination of these devices
provided the best protection.
In May, 1979, the United Auto Workers (UAW) petitioned OSHA to issue an Emergency Temporary Standard
(ETS) for locking out machinery and equipment, submitting case studies of fatalities involving 22 members
attributed to lockout-related causes since 1974. In September 1979, OSHA declined to issue an ETS, but said it
was drafting an Advance Notice of Proposed Rulemaking (ANPR) to address the issue.
In July 1983, OSHA drafted its first proposal of a LOTO standard and circulated it for feedback to associations,
companies, and unions. Most sources supported it. Some favored the use of locks rather than tags to secure
energy isolating devices; others wanted the flexibility of using either. Some objected to defining lockout of
activities as “normal production operations.”
In April 1988, OSHA’s official proposal for a LOTO standard was published in the Federal Register. Two public
hearings were conducted later in 1988, and an extended public comment period ran from April 1988 to May
1989. The most contested issues: 1) Is lockout/tagout required for normal production operations (which would
involve more downtime); and 2) Should locks or tags be the primary means to prevent operation of energy
isolating devices such as electrical disconnects, and hydraulic or pneumatic valves?
Finally, a Standard
In September, 1989, OSHA issued the final rule for lockout/tagout – more than 12 years after it began developing
requirements. The standard stated that servicing and maintenance activities, and also erection, installation,
construction, setup, changeover, and dismantling, must be performed with the equipment de-energized.
The standard would also cover lubricating, cleaning, unjamming, and making other minor adjustments and
simple tool changes that often take place during normal production operation, but may expose employees
to unexpected activation of the equipment or the unexpected release of energy. All of these activities OSHA
considered to be servicing and maintenance, and came under the scope of the standard.
OSHA provided this exception: the LOTO standard does not apply when certain minor servicing tasks are
conducted during normal production operations, such as: 1) repetitive adjustments; 2) tool changes, lubrication,
leak inspections, and other routine activities; 3) activities that are integral to the production process; and 4) work
is performed using alternative protective measures that provide effective employee protection. If an employer
can demonstrate that an alternative means enables the servicing employee to clean or unjam or in other ways
service the machine without being exposed to unexpected energization or activation of the equipment, the
LOTO standard does not apply.
In the final rule, OSHA determined that lockout, not tagout, is the preferred method of assuring de-energization
of equipment. But the agency stated that tagout will need to be used instead of lockout where the energy
control device cannot accept a locking device. When an energy control device is lockable, the standard requires
that lockout be used unless tagout can be shown to provide “full employee protection” equal to lockout.
After January 2, 1990, new machines, and modified or repaired older machines, had to be designed to accept
lockable energy isolating devices.
OSHA’s definition of lockout: “The placement of a lockout device on an energy isolating device, in accordance
with an established procedure, ensuring that the energy isolating device and the equipment being controlled
cannot be operated until the lockout device is removed.”
OSHA’s definition of tagout: “The placement of a tagout device on an energy isolating device, in accordance
with an established procedure, to indicate that the energy isolating device and the equipment being controlled
may not be operated until the tagout device is removed.”
• Writing specific procedures for each piece of equipment that identify all
energy sources and energy isolation devices. The procedure becomes a
checklist to assure that all energy sources are controlled before servicing and
maintenance starts. Specific procedural steps must be detailed for: 1) shutting
down, isolating, blocking, and securing machines or equipment to control
hazardous energy; 2) the placement, removal, and transfer of lockout or
tagout devices and the responsibility for them; and 3) for testing a machine
or equipment to determine and verify the effectiveness of lockout devices,
tagout devices, and other energy control measures.
• Training employees (called “authorized employees”) who apply locks and
tags, and employees (called “affected employees) who either operate the
machines where locks and tags are installed or whose jobs require them to
work in an area where servicing or maintenance is being done. Retraining
is required when jobs, machinery, or energy control procedures change, or
inspection reveals program inadequacies.
• Conducting audits at least every year of each procedure and reviewing
audit findings with each authorized employee where lockout is used, and
each authorized and affected employee where only tagout is used.
OSHA also has stated that discipline is the most critical factor to the success of a tagout program, though
OSHA does not regulate discipline in any of its standards. Discipline is key according to OSHA because tagging
out does not involve positive restraints on energy control devices; it requires constant vigilance to assure
tags are properly applied; tags must remain affixed throughout servicing and maintenance of equipment; and
no employee can violate the tag by reenergizing the equipment, intentionally or unintentionally, before the
tag is removed. Companies with effective tagout programs apply disciplinary action to both supervisors and
employees who violate tagout procedures, according to OSHA.
OSHA states that adequate training would be difficult for transient, short-term workers often employed in
longshoring, construction, and agriculture. Also, energy control procedures might vary widely from one worksite
to the next, and a construction worker could be employed at several sites in a single year. And maintenance
work on construction earthmoving equipment such as mobile cranes, front-end loaders, bulldozers, and dump
trucks requires the potentially hazardous positioning of buckets, blades, and vehicle body parts – safety issues
that are beyond the scope of general industry energy control.
By loading a tablet device with all of a company’s lockout/tagout procedures, employees can take a tablet to a
machine, follow the procedure, and safely lockout a piece of equipment. By syncing the tablet to the employer’s
shared drive, employees always will be using the most up-to-date copy of the lockout/tagout procedure.
Software programs now allow employers to track lockout/tagout use in real time. Managers can monitor which
employees are performing the lockout, what machines are being serviced, how long they are being worked on,
and how much downtime occurs each month.
Look for employees to use their smartphones to connect to the company database, select a procedure,
and show others they are working on the equipment with just a few clicks. Barcodes or QR codes can be
affixed to machines, making it easy for employees to scan and produce the needed procedures. And look for
preventive maintenance orders to be emailed or texted to the proper maintenance personnel, with a direct
link to the machine needing service. Corporate safety personnel will monitor lockout/tagout work on sites
around the world. On-site visits will occur less frequently as procedures become available online and webcams
capture employees engaged in servicing and maintaining machines and equipment. Technology will enable
corporations to standardize lockout/tagout programs with real-time verification and documentation.
PANDUIT CANADA PANDUIT EUROPE LTD. PANDUIT SINGAPORE PTE. LTD. PANDUIT JAPAN PANDUIT LATIN AMERICA PANDUIT AUSTRALIA PTY. LTD.
Markham, Ontario London, UK Republic of Singapore Tokyo, Japan Guadalajara, Mexico Victoria, Australia
cs-cdn@panduit.com cs-emea@panduit.com cs-ap@panduit.com cs-japan@panduit.com cs-la@panduit.com cs-aus@panduit.com
Phone: 800.777.3300 Phone: 44.20.8601.7200 Phone: 65.6305.7575 Phone: 81.3.6863.6000 Phone: 52.33.3777.6000 Phone: 61.3.9794.9020