01 HAZ Metal Stone Fixing Systems Brochure 2

Stone Fixing Systems
Technical Catalogue
HAZ-SF-EN/04.20
Your Fixing Systems Specialist
Stone Fixing Systems

Technical Product Catalogue
HAZ-SF-EN/04.20
Company Catalogue
HAZ.CC.EN.10.12
Demir Bank Headquarters, Istanbul
Contents
Company Profile 1
HDM Mortar Anchor Fixing Systems
Natural Stone Fixing System Overview 3
Introduction 34
Design Principles 5
Installation Detail 35
HZ Z Anchor Fixing System
BUN & BUG Product Details 36
Introduction 9
BTN & BTG Product Details 37
MTN & MTG Product Details 38
HZ01 Product Details 11
HN & HG Product Details 39
HSD Mortar Anchor Fixing Systems
Introduction 40
HRS1 Product Details 14
HRD01 Product Details 40
HSD Anchor Product Details 41
HMP Sub Channel Systems
HZ02-S Product Details 17
Introduction 42
Special Z Anchors 18
AXO Body Anchor Fixing Systems
ATS Channel System Introduction 44
Introduction 19
HMP Channel Product Details 45
HCSP Channel Restraint Product Details 46
BA Product Details 21
HCRS Channel Restraint Product Details 47
AXO1&2 Product Details 22
HMP Sub Channel Systems Examples 48
AXO3 Product Details 23
Special Sub Channel Systems 49
AXO4 Product Details 24
Aluminium Channel Systems 50
HRS3 Product Details 25
Heavy Duty Fixing Systems 52
HZTA Product Details 26
HCA Corner Anchors 54
Special Body Anchors 27
HAZ Accessories 55
HA L Anchor Fixing Systems
HB Expansion Bolts
Introduction 28
HB01, HB03 & HB05 Product Details 56
HB06, HB07 & HB11 Product Details 57
HA01 Product Details 30
References 58
HA02&HA03 Product Details 31
HA04&HA05 Product Details 32
Special L Anchors 33
HAZ Metal
• HAZ Metal Sanayi
Sanayi ve Ticaretve
A.S.Ticaret A.S. All
All rights reserved. Aprilrights reserved.
2020.Reproduction March of2012.
and distribution Reproduction
the information and
contained in this distribution
catalogue of the
is forbidden without information
prior
R
contained
written consent. HAZ Copyright. in this catalogue is forbidden
1
Natural Stone Fixing Systems - Overview
Company Profile
Introduction Mission Statement

HAZ Metal is located in Iskenderun, in the southern part of To design and produce products that exactly meet the expectations
Turkey,based in the company owned property, with an area of of our clients and provide them with technical service in order to
17.000 square meters. The company provides services in the design assist them with their requirements. Our objective is to propose the
and production of stainless steel fixing systems for natural stone most secure, economical and easy to use fixing systems to satisfy
installation and a variety of products used in construction. our clients.
The company’s objective is to assist and advise its clients in

choosing in the most suitable fixing systems for their requirements
Product Range
and to provide them with quality production and supply with timely
deliveries. HAZ Metal started producing fixing systems in 1993. Today, the
company has the technical know how and production capacity to
HAZ Metal has dedicated itself to supplying its clients with easy to produce all types of natural stone fixing systems used for ventilated
use, secure and economical fixing systems. Along with this stone facades. Production of a variety of fixing systems such as
principle, HAZ Metal has organized a technical department to channels, cast-in channels, masonry support anchors and expansion
design and produce fixing systems in accordance with bolts is also available.
international standards.
● Sub channel systems
HAZ Metal has 200 employees working both in Turkey and in foreign ● Anchor channel systems
branches. Along with a sales office in Istanbul, Turkey, there are ● Framing systems
HAZ branches in the United Arab Emirates, Germany, the United ● Brickwork support systems
Kingdom, Russia, Qatar, Egypt and Singapore. With this network, ● Concrete panel fixing systems
HAZ Metal reaches out closer to their clients, to provide better ● Structural Building components
services to meet local requirements. ● Expansion bolts
● Various construction accessories
The innovative design and production techniques offer practical
and economic solutions to solve every possible problem within the Standard and customized production is made to meet the special
scope of natural stone installation. As a supplier of fixing systems application requirements. Products are produced from stainless
to major projects around the world, HAZ Metal has proven its steel and galvanized steel raw materials. Stainless steel grade EN
quality and reliability to its clients. The company enjoys serving the 1.4301 (AISI304) & EN 1.4401 (AISI 316) and galvanized mild steel
sector and works hard to constantly improve and develop its
services.
Your Fixing Systems Specialist |2
Technical Service Production Capacity

HAZ Metal provides services in the design of fixing systems and With approximately 10.000 sqm of production halls, HAZ Metal
preparation of structural calculations. This service is done in the is equipped with 120 work stations and has a monthly
company technical department using CAD software and SAP and production capacity of more than 500 tons.
RFEM engineering programs.
Throughout the years, production techniques and methods have
The company’s technical staff consists of experienced engineers who been improved to achieve higher quality and productivity. HAZ
are competent in the field. Our engineers provide services in design, Metal today implements modern technology in the production of
anchor positioning, preparation of shop drawings and scheduling. fixing systems in order to meet the requirements of the industry.
The technical department receives the necessary technical The factory is equipped with a coil slitting machine, channel roll
information of the project in order to design the most suitable, secure, formers, press breaks, eccentric presses, automated end part
easy to use and economical fixing systems in accordance with the formers, thread rolling machines, cold forge bolt makers and
project criteria. Custom design and production is also made after various production units. There is also an in house electro
receiving detailed architectural drawings of the project. galvanizing unit where 12 micro thick zinc coating on mild steel
is made. Hot dip galvanizing with over 50 micro thick zinc
HAZ Metal provides the necessary documentation and structural coating is made by prequalified sources outside the factory.
calculation reports for submittal in order to approve the designed
fixing systems. Emphasis has also been given to automation in which faster
production and lower costs are achieved through higher
Quality Standards efficiency. HAZ Metal is able to design and build apparatus and
progressive dies in order speed up production.
HAZ Metal implements internationally recognised standards in the
design and production of ﬁxing systems. Product design and produc- The presence of a work shop with the capability of preparing and
tion is strictly controlled within the specifications of these standards. maintaining the required moulding and tooling, provides flexible
All products are designed and produced by its personnel, applying production. The quick preparation, maintenance, alteration and
the latest production methods with modern machinery. In order to adjustment of machines and tooling are made without
guarantee outstanding quality to their clients, HAZ Metal has interrupting the production process which leads to saving time
established a testing laboratory at the factory, to inspect materials and costs. This enables fast and flexible production to supply
during each stage of production. projects of any size.
3
Stone Fixing Systems - Overview
HZ Z Anchor Fixing System

Fixing systems need to accommodate all types of backing walls
whether they are concrete walls, block work & masonry walls or
steel structures.
The following points are taken into consideration when designing • Fixing to concrete with bolts.
a fixing system for natural stone installation. • Projection sizes up to 150 mm.
• Recommended for loads up to 800 N.
• Stone type and dimensions. • Installation at horizontal or vertical joints.
• Cavity structure: projection size and insulation. • Three dimensional adjustability.
• Application type: horizontal or vertical joint installation.
• Joint size.
• Structural wall backing.
• Height of facade.
• Relevant dynamic loads such as wind and seismic loads.
AXO Body Anchor Fixing
• Design criteria of the project.
HAZ Metal proposes and specially designs fixing systems

according to individual projects requirements. • Fixing to concrete with bolts.
• Projection sizes up to 260 mm.
• Recommended for loads up to 1300 N.
• Installation at horizontal or vertical joints.
• Optimum static performance.
• Three dimensional adjustability.
Direct fixing to concrete
walls with anchor bolts
Fixing to concrete with bolt

anchors using expansion bolts.
Insulation is cut at each anchoring HA L Anchor Fixing System
point.
• Fixing to concrete with bolts.

• Can be used for 50 mm and larger stone
thicknesses.
• Various types to enable adjustability.
• Installation at horizontal joints only.
Direct fixing to concrete or

masonry walls with mortar
Fixing to concrete with mortar HSD Mortar Anchor Fixing System

anchors using mortar. Insulation
is drilled at each anchoring point.
• Fixing to masonry with mortar.

• Various types to fit a range of loads and
projection sizes.
• Installation at horizontal or vertical joints.
• Three dimensional adjustability.
Indirect fixing to load

bearing beams with HMP Sub Channel System
channel system
• Fixing to sub channel structure which is
Fixing to sub channel structure attached to load bearing beams.
supported to load bearing beams. • High load bearing capability to fit projection
Insulation is cut at each anchoring sizes up to 360 mm.
point. • Greater projection sizes are achieved with
special design.
• Fully adjustable and allows fast installation.
Stone Fixing Systems - Overview
HAZ Metal is known as a high quality and reliable service provider for the design and supply of fixing systems in the construction industry.
Major projects have been successfully supplied with HAZ Metal fixing systems. The main advantage of HAZ Metal is the ability to custom
design fixing systems and provide fast production to meet the time restraint requirements of projects. The design and supply is done in
accordance with international standards and more importantly with our customers’ expectations.
Application examples for bolt anchors

Anchors are fixed on to load bearing walls
with expansion bolts.
To fasten anchors on to isolated walls, the

isolation must be cut first. After fastening, the
cut out isolation piece must be inserted back,
and the isolation parts must be sealed in order
to reduce cold bridging.
Application examples of profile systems

The channels are fastened to channel supports
which are fixed with expansion bolts to floor
beams. Natural stone panels are fixed with
anchors which are fixed to channels with hex.
bolt sets. This system allows installation to be
independent from the wall. Low anchoring
points allows faster installation and reduces
cold bridging.
5
Design Principles
Technical Design & Engineering

HAZ Metal provides services in the design of fixing systems and the
preparation of structural calculations. This service is done in the company
technical department using CAD software and SAP and RFEM stress analysis
programs.
Our technical department receives the necessary technical information of the

project in order to propose the most suitable, secure, easy to use and
economical fixing systems in accordance with the project criteria. Custom
design is also made in accordance with the architectural drawings of the
project.
HAZ Metal provides the necessary technical documentation for submittal to

the project officials in order to receive approval for the fixing system
elements. The following principles are used in the design and structural • Shop drawing with application details
calculations for natural stone fixing systems.
Finite element stress analysis is implemented for complex structures where

the structural integrity of the fixing systems needs to be maintained. This
procedure is especially made for sub channel systems and unitised panel
facade units.
HAZ Metal can offer the design and engineering services by referring to any
internationally renown standards. The engineering department will relate to the
specifications of the project and conduct its design and dimensioning
according to the requested criteria.
Reference is made to the following standards:
British Standards
BS 8298 • Design and installation of natural stone cladding

BS EN 10088-2 • Steel plates, sheets and strips stainless and heat
resisting • Structural analysis report
BS 6105 • Corrosion resistant stainless steel fasteners
BS 5950 • Structural use of steel work in building
BS 6399 Part 2 • Code of practice for wind loads
BS 970 Part 3 • Mechanical properties for stainless steel
German Standards
DIN 18 516 • Cladding for ventilated walls

DIN 18 800 • Steel structures, design and dimensioning
DIN 18 801 • Steel framed structures
DIN 1045 • Concrete and reinforced concrete, design and
dimensioning
DIN 1053 • Masonry, design and dimensioning
DIN 1055 • Wind loads design code
DIN 4114 • Steel construction, stability cases
• Structural analysis report
American Standards
ASTM C1242 -12 • Standard guide for stone attachment systems

ASTM A 276 • Specificationfor stainless steel bars and shapes
ASTM 666 • Specification for annealed or cold worked
austenitic stainless steel sheets
ASCE • Minimum design loads for buildings
Uniform Building Code & International Building Code
Euro codes
EN 1990 Basis of Structural Design. Structural Analysis and

Design by Testing
EN 1090 Execution of steel & aluminium structures
EN 1991 General Actions - Wind
EN 1998 General Rules, seismic actions and rules for buildings • Finite element method stress analysis
Design Principles
Design Factors
The following design factors are considered
Wall Structure Natural Stone Material

I : Thickness of insulation Dimensions of natural stone slabs : Design weight for natural stone
C : Cavity slabs : (ds)
St : Thickness of stone • Length: (w) • Travertine: (24000 N/m3)
K : Projection • Height: (h)
• Thickness: (St) • Sandstone: (26000 N/m3)
h • Marble
&Limestone: (27000 N/m3)
St C I
• Granite: (28000 N/m3)
K
St w
Structure - Edge Spacing Anchor Pins

• Minimum distance from the corner of the slab to the pin centre • Anchor pins are inserted
should be 2.5 times the slab thickness. into the drilled holes on the
edge of the slab from four
• The minimum pin centre distance to the edge of slab at the points.
surface should be 15mm.
• Drilled holes should be
• The most secure method is to arrange the distance of the aprox. 3 mm wider than the
drilled pin hole centre from the edge of the slab at 1/4 the size pin diameter and minimum
of the slab. 25 mm in length.
W • Minimum 2 mm space
should be left between the
h/1
slab below and the bottom
edge of the adjustable arm.
h/2
• A plastic tube is inserted
on the slabs below to
h/3
absorb wind loads.
≥2,5 x St St ≥30 w/2 w/3 w/4
Applied Loads - (Actions)

The following applied loads are considered;
Dead loads:
Weight of natural stone slabs is determined
Fdw= h (m) x w (m) x st(m) ds (KN/m3)
Fdw is multiplied with 1.35 safety factor.
Wind loads:
The max. speed is; vs.
The value of the dynamic pressure of the wind
is q=k Vs2
The max. design pressure is; wp=cp.Q
The max. design suction is; ws=cs.Q
ws=0.7.Q (normal)
ws=2.0.Q (edge)
wp & ws are multiplied with 1.50 safety factor
Thermal loading:
The following temperature is considered.
Range on the stone; Tmin ºC < t ºC < tmax ºC

The max. thermal loading in the stone is;
∆t=tmax - tmin The max. thermal expansion
for stone slab is; ∆l=µ.∆t.L
7
Design Principles
Wall Backing Group of Bolts

The anchoring ground can be concrete, brickwork, filled hollow block or The distance between anchor bolts; A, which is necessary for a full
steel structure. Different types of bolts are used for backing. cone of concrete to break away, is given by the crater diameter; C,
depending on the type of anchor. This diameter is 1.5 to 2.5 times the
The type of wall backing is taken into consideration to propose suitable depth of embedment, D.
bolts for fixing the anchors.
Concrete wall Masonry wall Block work wall
Application Type
Horizontal Joints
The anchors carry half the weight of the natural stone slabs in horizontal installation. Anchors bear half the weight of the slab above and also
act as restraint, holding the slabs below and restraining them against wind pressure and suction.

Load Bearing & Restraint Min. Projection size 45 mm
Restraint
Load Bearing
Indirect fixing to channels
Min. Projection size 90 mm.
Vertical Joints
The load bearing anchors carry the full weight of the natural stone slab in vertical installation. Each anchor bears half the weight of the slab on
the right and half the weight of the slab on the left. Restraint anchors hold the slabs below and restrain them against wind pressure and
suction.

Min. Projection size 45 mm
Load Bearing Restraint

Indirect fixing to channels
& Restraint Min. Projection size 90 mm.
Design Principles
Load Principles
Vertical (Dead Load) and Horizontal (Wind Load) loads are determined according to the following diagram. The following principle is applied
before designing a fixing system.
Support anchor in horizontal joint Restraint anchor in horizontal joint
Vertical load from dead load FWP = (w x h x qp) / 2 ( for each anchor)
FDW = (st x w x h x ds) / 2 (for each anchor) FWS = (w x h x qs) / 2 ( for each anchor)
FDW
FWS / FWP
FDW = Dead load ds = Density of stone t = Thickness of stone

FWP = Wind load at pressure case qw = Design wind pressure w = Width of stone
FWS = Wind load at suction case qs = Design wind suction h = Height of stone
Support anchor in vertical joint Restraint anchor in vertical joint
Vertical load from dead load FWP = (w x h x qp) / 2 ( for each anchor)
FDW = (st x w x h x ds) / 1 (for each anchor) FWS = (w x h x qs) / 2 ( for each anchor)
FWS / FWP
FDW
Material Grade
Product Type Stainless Steel Steel
Anchors, adjustable arms and pins must AISI = W.-Nr. DIN = W. -Nr.
be stainless steel grade AISI 304 - 1.4301 304 = 1.4301
(A2) & AISI 316-1.4401 (A4). Anchors 316 = 1.4401 Not Advisable
316Ti = 1.4571
Recommended material specifications for
304 = 1.4301 Hot dip galv. St 37-2 = 1.0037
fixing systems are shown in the following Channels Hot dip galv. St 44-2 = 1.0044
316 = 1.4401
table.
DIN 933
Bolts Electro galv. St 37
(A2/50-A2/70)
Strength class 4.6/8.8
A4/50-A4/70)
DIN 934 & DIN 439
Hexagon Nuts Electro galv. St 37
(A2/50-A2/70)
Strength class 8
A4/50-A4/70)
Washers DIN 125 ST DIN 125
9
HZ Z Anchor Fixing Systems - Introduction
• Direct fixing into concrete walls with expansion bolts. Indirect fixing into sub channel system with hex bolts.
• Three dimensional adjustability - Quick and easy fixing.
• Installation at horizontal and vertical joints.
• Recommended projection sizes up to 150 mm & loads up to 800 N.
HZ01 HZ02 HZ05 Z Anchor HZ07 HZ08 Z Anchor HRS1

Z Anchor Z Anchor With riveted nut Soffit Anchor For large projections Restraint Anchor
Three dimensional adjustability
1) Vertical adjustment is 2) Adjustment of the 3) Adjustment of the

provided by the slotted projection size is anchor left and right is
hole. The anchor is fixed provided by rotating the provided by sliding the
on to the bolt with the adjustable arm. The body up to 15 degrees
serrated washer at the adjustable arm is locked side ways.
desired level. with the hexagon nut.
Installation at horizontal joints Installation at vertical joints
Load Bearing & Load

Restraint Bearing
Restraint
• Suitable for concrete walls. Anchors are fixed directly on to concrete walls with expansion bolts.
• Recommended projection size between 45 mm to 135 mm and loads up to 800 N.
• In horizontal joint installation, slabs are pinned on the bottom and upper sides. Anchors act as load bearing carrying half the weight of
the slabs above. Anchors also act as restraints, holding the slabs below and restraining against wind suction and pressure.
• In vertical joint installation slabs are pinned on the left and right sides. Anchors on the bottom are load-bearing anchors carrying the
whole weight of the slab. Half the weight of the slab on the left and half the weight of the slab on the right. Anchors on the top are
restraint anchors holding the slabs and restraining against wind suction and pressure.
• Three - dimensional adjustability allows quick and easy installation.
• The design and structural calculations of these anchors are made in our technical department. Special design and manufacturing can
be made for the requirements of each project.
Your Fixing Systems Specialist | 10
HZ Z Anchor Fixing Systems - Installation Detail

Adjustable Arm Variations
Shape A Shape B
Shape C Shape D
Shape E Shape F
Shape G Shape H
1- Through bolt
A 2- Anchor body
3- Serrated washer
4- Round washer
5- Hex nut for through bolt Shape J Shape K
6- Hex nut for adjustable arm
7- Adjustable arm
8- Plastic tube
9- Flanged pin
Installation at horizontal joints

Elevation view Section a-a Installation details
Restraint
HZ02 Z Anchor Load Bearing

& Restraint
Load Bearing
Installation at vertical joints

Restraint
HZ02 Z Anchor
Load Bearing
HRS01 Restraint Anchor

Load Bearing
& Restraint
11
HZ01 Z Anchor - Product Details
Fdw
For anchoring into
concrete ≥ C20/25
Cement
grout K
E.b.
Load
Bearing
Fws/Fwp Drilled hole may be

T M required for closely
spaced walls.
Ø
Restraint EAL
Plastic
tube
F
St=20-50 mm
St
Technical details
Projec- Min. Max. Dead Forming Wind- Wind- Expansion Pin Adj. Arm Adj. Arm Adj. Arm
Product
tion Projec- Projec- Load Size Pressure Suction Bolt Size Size Metric Flat Length
Code
tion tion Size Thickness
K (mm) K - (mm) K + (mm) Fdw (N) F (mm) Fwp (N) Fws (N) E.b. (mm) ø (mm) M (mm) T (mm) EAL (mm)
HZ01-452 45 40 55 10 60
HZ01-552 55 45 70 20 60
200 312 219 M8X80 5 M10 3.5
HZ01-752 75 60 90 40 60
HZ01-952 95 80 110 60 60
HZ01-553 55 50 70 20 60
HZ01-753 75 60 90 40 60
300 468 328 M8X80 5 M10 3.5
HZ01-953 95 80 110 60 60
HZ01-1153 115 100 130 80 60
HZ01-554 55 50 65 10 70
HZ01-754 75 60 90 20 90
400 624 437 M10X90 5 M12 4.5
HZ01-954 95 80 110 40 90
HZ01-1154 115 100 130 60 90
HZ01-755 75 60 90 20 90
HZ01-955 95 80 110 40 90
500 780 546 M10X90 5 M12 4.5
HZ01-1155 115 100 130 60 90
HZ01-1355 135 120 150 80 90
• Material: Stainless Steel 1.4301 (A2) & 1.4401 (A4).

• Table above is prepared according to Eurocode standards.
• Loads stated are working resistance loads.
• Other sizes are available for production upon request.
• Bolts are provided separately.
• Structural calculation reports are available upon order.
HZ01 Z Anchor
• Load bearing & restraint • Projection sizes between 45 and 150 mm • Loads up to 500 N
• Three dimensional adjustability • Suitable for horizontal & vertical joints • Stone thicknesses 20-50 mm
• Fastened on to load bearing walls with expansion bolts and on to channels with set screws
Product Code Description Shape A Shape B Shape C Shape D
HZ01 - 45 2 A
Shape
Dead Load (x10 Kg)
Projection (mm)
Type
Fdw
For anchoring into
concrete ≥ C20/25
Cement
grout K
E.b.
Load
Bearing

spaced walls.
Restraint EAL
Plastic
tube
F
St St=20-50 mm
Technical Details
Product
Code
HZ02-452 45 40 55 10 60
HZ02-552 55 45 70 20 60
200 312 219 M8X80 5 M10 3.5
HZ02-752 75 60 90 40 60
HZ02-952 95 80 110 60 60
HZ02-553 55 45 70 20 60
HZ02-753 75 60 90 40 60
300 468 328 M8X80 5 M10 3.5
HZ02-953 95 80 110 60 60
HZ02-1153 115 100 130 80 60
HZ02-554 55 45 65 10 70
HZ02-754 75 60 90 20 90
400 624 437 M8X80 5 M12 4.5
HZ02-954 95 80 110 40 90
HZ02-1154 115 100 130 60 90
HZ02-755 75 60 90 20 90
HZ02-955 95 80 110 40 90
500 780 546 M8X80 5 M12 4.5
HZ02-1155 115 100 130 60 90
HZ02-1355 135 120 150 80 90
HZ02-756 75 60 90 20 90
HZ02-956 95 80 110 40 90
600 936 655 M10X90 6 M14 5.5
HZ02-1156 115 100 130 60 90
HZ02-1356 135 120 150 80 90
HZ02-758 75 60 90 20 90
HZ02-958 95 80 110 40 90
800 1235 865 M10X90 6 M14 5.5
HZ02-1158 115 100 130 60 90
HZ02-1358 135 120 150 80 90
• Material : Stainless Steel 1.4301 (A2) & 1.4401 (A4).• Table above is prepared according to Eurocode standard.• Loads
stated are working resistance loads. • Other sizes are available for production upon request. • Bolts are provided
separately. • Structural calculation reports are available upon order.
HZ02 Z Anchor
HZ02 - 45 2 A
Shape
Dead Load (x10 Kg)
Projection (mm)
Type
13
HZ05 Z Anchor With Riveted Nut - Product Details
Fdw
For anchoring into
concrete ≥ C20/25
Cement
grout K
E.b.
Load
Bearing

spaced walls.
Restraint EAL
Plastic
tube
F
St St=20-50 mm
Technical Details
Product
Code
HZ05-452 45 40 55 10 60
HZ05-552 55 45 70 20 60
200 312 219 M8X80 5 M10 3.5
HZ05-752 75 60 90 40 60
HZ05-952 95 80 110 60 60
HZ05-553 55 50 70 20 70
HZ05-753 75 60 90 40 70
300 468 328 M8X80 5 M10 3.5
HZ05-953 95 80 110 60 70
HZ05-1153 115 100 130 80 70
HZ05-554 55 50 65 10 70
HZ05-754 75 60 90 20 90
400 624 437 M8X80 5 M12 4.5
HZ05-954 95 80 110 40 90
HZ05-1154 115 100 130 60 90
HZ05-755 75 60 90 20 90
HZ05-955 95 80 110 40 90
500 780 546 M8X80 5 M12 4.5
HZ05-1155 115 100 130 60 90
HZ05-1355 135 120 150 80 90
• Material : Stainless Steel 1.4301 (A2) & 1.4401 (A4).

• Table above is prepared according to Eurocode standard.
adjustability
HZ05 Z Anchor
HZ05 - 45 2 A
Shape
Dead Load (x10 Kg)
Projection (mm)
Type
HRS1 Restraint Anchor - Product Details
K For anchoring into

concrete ≥C20/25
Cement
Grout
Restraint E.b.
Fws/Fwp
T M
Plastic Ø EAL
Tube
St St=20-50 mm
Technical Details
Projec- Min. Max. Forming Wind- Wind- Expansion Pin Adj. Arm Adj. Arm Adj. Arm
Product
tion Projec- Projec- Size Pressure Suction Bolt Size Size Metric Flat Length
Code
K (mm) K - (mm) K + (mm) F (mm) Fwp (N) Fws (N) E.b. (mm) ø (mm) M (mm) T (mm) EAL (mm)
HRS1-55 * 55 45 60 20 60
HRS1-75 75 60 90 40 60
HRS1-95 95 80 110 60 312 219 M8X80 5 M8 3 60
HRS1-115 115 100 130 60 80
HRS1-135 135 115 150 60 100

• Available in sizes to fit the projection range of all HZ anchors.
* In case back adjustment shorter adj. arms should be used.

HRS1 - 45 A
Shape
Projection (K mm)
Type
15
HZ07 Z Anchor For Soffits - Product Details

For anchoring into
concrete ≥C20/25
E.b. E.b.
M
F
K
EAL
St
Ø
T
Fdw
Cement Grout Plastic Tube
Technical Details
Projec- Min. Max. Dead Forming Expansion Pin Adj. Arm Adj. Arm Adj. Arm
Product
tion Projec- Projec- Load Size Bolt Size Size Metric Flat Length
Code
K (mm) K - (mm) K + (mm) Fdw (N) F (mm) E.b. (mm) ø (mm) M (mm) T (mm) EAL (mm)
HZ07-452 45 40 55 10 60
HZ07-552 55 45 70 20 60
200 M8X80 5 M10 3.5
HZ07-752 75 60 90 40 60
HZ07-952 95 80 110 60 60
HZ07-553 55 50 70 20 60
HZ07-753 75 60 90 40 60
300 M8X80 5 M10 3.5
HZ07-953 95 80 110 60 60
HZ07-1153 115 100 130 80 60
HZ07-554 55 50 65 10 70
HZ07-754 75 60 90 20 80
400 M8X80 5 M12 4.5
HZ07-954 95 80 110 40 80
HZ07-1154 115 100 130 60 80

HZ07 Z Anchor - Soffit Anchor

• Load bearing & restraint • Projection sizes between 45 and 130 mm
• Three dimensional adjustability • Suitable for horizontal & vertical joints • Loads up to 400 N
• Fastened on to load bearing walls with expansion bolts and on to channels with set screws • Stone thicknesses 20-50 mm
HZ07 - 45 2 A
Shape
Dead Load (x10 Kg)
Projection (mm)
Type
Fdw
For anchoring into
concrete ≥ C20/25
Cement K
grout
E.b.
Load
Bearing
Fws/Fwp
T M M
Restraint EAL
Plastic
tube
F
St St=20-50 mm
Technical Details
Product
Code
HZ08-1152 115 85 130 80 60
HZ08-1352 135 105 150 200 100 312 219 M8x80 5 M10 3.5 60
HZ08-1552 155 135 170 120 60
HZ08-1153 115 100 130 80 60
HZ08-1353 135 120 150 300 100 468 328 M8x80 5 M10 3.5 60
HZ08-1553 155 140 170 120 60
HZ08-1154 115 100 130 80 80
HZ08-1354 135 120 150 400 100 624 437 M8x80 5 M12 4.5 80
HZ08-1554 155 140 170 120 80

HZ08 Z Anchor
HZ08 - 115 2 A
Shape
Dead Load (x10 Kg)
Projection (mm)
Type
17
HZ02-S Z Anchor - Product Details

A
B Fdw
For anchoring into
concrete ≥ C20/25
2 5 mm
9 mm Cement
Grout K
LGA TEST REPORT Load E.b.
No : BBW 121 51 21 Bearing
Date : 15.10.2006
M

F T M required for closely
spaced walls.
Ø
M T
Restraint EAL
Plastic
Ø Tube &
EA L
70
Cement Grout F
St St=20-50 mm
Technical Details
Projec- Min. Max. Dead Offset Wind- Wind- Bolt Pin Adj. Arm Adj. Arm Adj. Arm
Product
tion Projec- Projec- Load Pressure Suction Size Diameter Metric Flat Length
Code
HZ02-S-33010/10 40 40 50 500 10 50
HZ02-S-33015/10 45 45 55 500 15 50
HZ02-S-33020/10 50 50 60 500 20 50
HZ02-S-33030/10 65 50 80 400 30 60
HZ02-S-33040/10 75 60 90 400 40 M10 3.5 60
HZ02-S-33050/10 85 70 100 400 50 60
HZ02-S-33060/10 95 80 110 300 60 60
HZ02-S-33080/10 125 110 140 300 80 312 219 M8x80 ø 5x70 70
HZ02-S-330100/10 145 130 160 250 100 70
HZ02-S-330120/10 165 150 180 250 120 70
HZ02-S-43020/12 60 55 70 500 20 70
HZ02-S-43040/12 90 75 105 500 40 80
HZ02-S-43060/12 110 95 125 400 60 M12 4.5 80
HZ02-S-43080/12 130 115 145 400 80 80
HZ02-S-430100/12 150 135 165 300 100 80
HZ02-S-430120/12 170 155 185 300 120 80

• Table above is prepared according to LGA test results.
• Loads stated are characteristic resistance loads.
• Max Wind pressure: 350 N
•Test results are available upon order.
HZ02-S type Z anchors with HZ02-2S Type without HZ05-S Type with HZ05-2S Type with Shape A Shape B
standard sizes. Different serration and with riveted nut. Serrated riveted nut. Without
types available according to plain washer. with serrated serration and with
desired method of fixation. washer. plain washer.
Product Code Description Shape C Shape D
HZ02-S - 330 / 10 A
Shape
Adj. arm M size (mm)
Anchor body size (mm)
Anchor type
HZ Z Anchor - Special Applications Details
HZ03 Special Z Anchor
Used for installing soffit and facade panels

with a single anchor
HZ06 Special Z Anchor - for large projection sizes
With optimal static performance

Can be used for projections over 150 mm
HZ09 Z Anchor - with wedge washer
Can be used for loads that are over 800 N when stronger
vertical stabilization is required
Special Designs
Z Anchors are fixed on sub frame to Z Anchors are fixed on to special steel Z Anchors are fixed on to special steel
install cornice lining. structure for cornice parapet installation. structure for special area installation.
19
AXO Body Anchor Fixing Systems - Introduction
• Direct fixing in to concrete walls with expansion bolts. Indirect fixing on to sub channel systems with hex bolts.
• Three dimensional adjustability - Quick and easy fixing.
• Installation at horizontal and vertical joints.
• Optimum static performance and low engineering for higher loads and larger projection sizes.
• Recommended projection sizes up to 260 mm and loads up to 1300 N.
AXO1 AXO2 AXO3 AXO4 HRS3 HZTA

Body Anchor Body Anchor Body Anchor Body Anchor Restraint Anchor Telescope Anchor
Three dimensional adjustability
1) Vertical adjustment is provided 2) Adjusting the projection size by simply 3) Adjusting the anchor left and right is
through the body space. The anchor is moving the adjustable arm without provided by sliding the body up to 15
fixed onto the bolt through the wedge rotating. The adjustable arm is safely degrees left or right.
washer and the lock washer at the fixed to the anchor body with the lock
desired level. nut and hex bolt.
Installation at horizontal joints Installation at vertical joints
Load Bearing & Load

Restraint Restraint Bearing
• Suitable for concrete walls. Anchors are fixed on to concrete walls with expansion bolts.
• Projection sizes between 60 and 260 mm and loads up to 1300 N.
• In horizontal installation, slabs are pinned on the bottom and upper sides. The anchors act as load bearing, carrying half the weight of
the slabs above. Anchors also act as restraint holding the slabs below and restraining against wind suction and pressure.
• In vertical installation, slabs are pinned at the left and right sides. The anchors on the bottom are load-bearing anchors carrying the
whole weight of the slab. Half the weight of the slab on the left and half the weight of the slab on the right. The anchors on the top are
restraint anchors holding the slabs and restraining against wind suction and pressure.
• Three dimensional adjustability allows quick and easy installation.
• The design and structural calculations of these anchors are made in our technical department. Special design and manufacturing can
be made for the requirements of the project.
AXO Body Anchor Fixing Systems - Installation Details

Adjustable Arm Variations
Shape A Shape B
Shape C Shape D
Shape E Shape F
1- Through bolt Shape G Shape H

2- Wedge washer
3- Anchor body
4- Lock washer
5- Round washer for through bolt
6- Hex nut for through bolt
7- Locking plate Shape J Shape K
8- Hex bolt
9- Adjustable arm
10- Plastic tube
11- Flanged pin

Restraint
AXO4
Body Anchor
Load Bearing
& Restraint
Load Bearing

Restraint
Load Bearing
AXO4 Load Bearing

& Restraint
Body Anchor
21
BA Body Anchor - Product Details

Fdw
For anchoring into
concrete ≥ C20/25
K
Cement
grout
E.b.
LGA TEST REPORT Load

bearing
No : BBW 0541135-01
Date : 09.05.2005 x
Fws/Fwp
T M
Body 1607
Restraint Ø
Body 1207
Body 858 EAL
Body 609 Plastic
tube
St F St=20-50 mm
Fdw
For anchoring into
concrete ≥ C20/25
K
Cement
grout
E.b.
Load
bearing
x
Fws/Fwp
T M
Ø
Ø
Restraint
EAL
Plastic
tube
St F St=20-50 mm
Technical Details
Projec- Min. Max. Dead Forming Wind- Wind- Expansion Pin Adj. Arm Adj. Arm Adj. Arm X
Product
tion Projec- Projec- Load Size Pressure Suction Bolt Size Size Metric Flat Length Size
Code tion tion Size Thickness
K (mm) K - (mm) K + (mm) Fdw (N) F (mm) Fwp (N) Fws (N) E.b. (mm) ø (mm) M (mm) T (mm) EAL (mm) x (mm)
BA-609 BODY 1 60 50 75 900 28 1100 770 70
BA-858 BODY 2 85 70 100 800 46 700 700 70
M8X80 5 M12 4.5 50
BA-1207 BODY 3 120 95 135 700 75 650 650 80
BA-1607 BODY 4 160 145 175 700 115 600 600 80

• Table above is prepared according to LGA test results.
• Loads stated are characteristic resistance loads.
• Test results are available upon order.
BA Body Anchor
BA - 60 9 A
Shape
Dead Load (x10 Kg)
Projection (K mm)
Type
AXO1 & AXO2 Body Anchor - Product Details

Fdw
For anchoring into
concrete ≥ C20/25
K
Cement
grout
E.b.
AX01 AX02 Load
bearing
Body Anchor Body Anchor
x
Fws/Fwp
T M
Restraint Ø
EAL
Plastic
tube
St St=20-50 mm
F
Fdw
For anchoring into
concrete ≥ C20/25
K
Cement
grout
E.b.
Load
bearing
x
Fws/Fwp
T M
Ø
Ø
Restraint
EAL
Plastic
tube
St F St=20-50 mm
Technical Details
Product
AXO1-705 70 55 85 20
500 780 546 M8X80 5 M12 4.5 80 50
AXO1-1105 110 95 125 60
AXO1-7013 70 55 85 20 80 50
1300 2028 1419 M10X90 6 M16 6
AXO1-11013 110 95 125 60
AXO2-1505 150 135 165 500 100 780 546 M8X80 5 M12 4.5 80 50
AXO2-15013 150 135 165 1300 100 2028 1419 M10X90 6 M16 6

• Structural calculations are available upon order.
AXO1 & AXO2 Body Anchor

AXO1 - 60 9 A
Shape
Dead Load (x10 Kg)
Projection (K mm)
Type
23
AXO3 Body Anchor - Product Details
Fdw
For anchoring into
concrete ≥ C20/25
K
Cement
Grout
E.b.
Load
Bearing
x
Fws/Fwp
T M
Ø
Restraint EAL
Plastic
Tube &
F
St St=20-50 mm
Technical Details
Product
AXO3-2005 200 180 220 155
AXO3-2205 220 200 240 175
500 780 546 M8X120 5 M12 4.5 80 75
AXO3-2405 240 220 260 195
AXO3-2605 260 240 280 215
AXO3-2009 200 180 220 155
AXO3-2209 220 200 240 175
AXO3-2409 240 220 260 900 195 1430 1000 M10X130 6 M14 5.5 80 75
AXO3-2609 260 240 280 215

AXO3-20013 200 180 220 155
AXO3-22013 220 200 240 175
1300 2028 1419 M12X145 6 M16 6 80 80
AXO3-24013 240 220 260 195
AXO3-26013 260 240 280 215

• Table above is prepared according to Eurocode standard
AXO3 Body Anchor

AXO3 - 200 5 A
Shape
Dead Load (x10 Kg)
Projection (K mm)
Type
AXO4 Body Anchor - Product Details

Fdw
For anchoring into
concrete ≥ C20/25
K
Cement
Grout
E.b.
Load
Bearing
x
Fws/Fwp
T M
Ø
Restraint EAL
Plastic
Tube &
F
St St=20-50 mm
Technical Details
Product
AXO4-1605 160 140 180 115
AXO4-1805 180 160 200 135
AXO4-2005 200 180 220 155
500 780 546 M8X120 5 M12 4.5 100 75
AXO4-2205 220 200 240 175
AXO4-2405 240 220 260 195
AXO4-2605 260 240 280 215
AXO4-1609 160 140 180 115
AXO4-1809 180 160 200 135
AXO4-2009 200 180 220 155
900 1430 1000 M10X130 6 M14 5.5 100 75
AXO4-2209 220 200 240 175
AXO4-2409 240 220 260 195
AXO4-2609 260 240 280 215
AXO4-16013 160 140 180 115
AXO4-18013 180 160 200 135
AXO4-20013 200 180 220 155
2028 1419 M12X145 6 M16 6 100 80
AXO4-22013 220 200 240 1300 175
AXO4-24013 240 220 260 195
AXO4-26013 260 240 280 215

AXO4 Body Anchor

AXO4 - 160 5 A
Shape
Dead Load (x10 Kg)
Projection (K mm)
Type
25
HRS3 Restraint Anchor - Product Details
For anchoring into

K concrete ≥ C20/25
Cement Restraint E.b.

Grout
x
T Fws/Fwp M
Plastic Ø
Tube &
EAL
St F
St=20-50 mm
• Available in sizes to fit the projection range of all AXO anchors.
Technical Details
Projec- Min. Max. Forming Wind- Wind- Expansion Pin Adj. Arm Adj. Arm Adj. Arm X
Product
tion Projec- Projec- Size Pressure Suction Bolt Size Size Metric Flat Length Size
Code
K (mm) K - (mm) K + (mm) F (mm) Fwp (N) Fws (N) E.b. (mm) ø (mm) M (mm) T (mm) EAL (mm) x (mm)
HRS03-60 60 40 80 70
25
HRS03-80 80 60 100 90
HRS03-100 100 80 120 100
HRS03-120 120 100 140 120
HRS03-140 140 120 160 32 140
HRS03-160 160 140 180 2028 1419 M8X80 5 M8 3 160 30
HRS03-180 180 160 200 170
HRS03-200 200 180 220 40 190
HRS03-220 220 200 240 210
HRS03-240 240 220 260 220
HRS03-260 260 240 280 50 240
• Material: Stainless Steel 1.4301 (A2) & 1.4401 (A4)

• Table above is prepared according to Eurocode standard
• Loads stated are working resistance loads
• Other sizes are available for production upon request
• Bolts are provided separately
• Structural calculation reports are available upon order

HRS03 - 60 A
Shape
Projection (K mm)
Type
HZTA Telescope Anchor - Product Details

Fdw
For anchoring into
concrete ≥ C20/25
K
Cement
Grout E.b.
Load
Bearing
x
Fws/Fwp
T M
Ø
Restraint EAL
Plastic
Tube &
F
St
St=30-50 mm
Technical Details
Product
tion Projec- Projec- Load Size Pressure Suction Bolt Size Size Dia. Flat Length Size
Code tion tion Thickness
HZTA-15011 150 135 165 90
HZTA-18011 180 165 195 120
HZTA-21011 210 195 225 150
1100 1300 1300 M10 6 Ø21,3 4 132 75
HZTA-24011 240 225 255 180
HZTA-27011 270 255 285 210
HZTA-30011 300 285 315 240

HZTA Telescope Anchor

Product Code Description Shape A Shape B
HZTA - 150 11
Dead Load
Projection (K mm)
Type
27
AXO Body Anchor - Special Application Details
Body anchor with welded plate

with two pins. Used for stone
installation with single anchor.
This type used for installation
of reveals with maximum width
of 25 cm.
Body anchor with welded shims

and HB09 execution. With this
type of anchor, stone panels are
supported from the rear surface
using HB09 bolts instead of
from the edges using pins.
Body anchor with welded plate

and riveted nut. A feature of
HZ05 which is chosen for the
fine adjustment of the projection
by spinning or rotating the
riveted nut while pins are set on
the stone.
Special Designs
Body anchors are used for stone Body anchors are used to form an oval Body anchors used for installation of
installation around columns. column in natural stone. parapet area.
t:
5m
m
t:
5m
m
HA L Anchor Fixing Systems - Introduction
• Direct fixing into concrete walls with expansion bolts. Indirect fixing onto sub channel system with hex bolts.
• Economical & easy fixing.
• Installation at horizontal joints.
• Adjustability provided through adjustable plates and slot pin holes.
HA01 L Anchor HA02 L Anchor HA03 L Anchor HA04 L Anchor HA05 L Anchor With Adj. Plate
Double Pin With Kerf With Adjustable Plate & Welded Tie
Adjustability
1. Vertical adjustment is made through 3. Greater projection sizes can be

the slot hole. The anchor is fixed on to achieved by using shims. Shims are
the bolt with the serrated washer and placed at the back of the anchor.
nut.
4. An adjustment plate is available in
2. A slot pin hole can be provided to HA04 & HA05 type L anchors where
enable lateral adjustment of the pin. adjustment of the projection size can be
made.
Fdw/2 Fdw/2
Load Bearing &

Restraint
HA01 L Anchors HA03 L Anchors HA04 L Anchors
• Suitable for concrete walls. • Suitable for concrete walls. • Suitable for concrete walls.
Recommended projection sizes up to Recommended projection sizes up to Recommended projection sizes up to
55 mm. 55 mm. 180 mm.
• Slabs are pinned at the bottom and • Slabs have slits and the kerf parts of • Slabs are pinned from the bottom and
upper sides. the anchors are inserted in to the slit upper sides.
• Adjustability for projection size can be edges of the slabs. • Adjustability of the projection size is
done by inserting shims between the • Adjustability for projection size can be enabled with the adjustable plate, which
anchor and the wall. done by inserting shims between the is fixed to the body with hex bolts.
• Anchors act as load bearing and anchor and the wall. • Anchors act as load bearing and
restraint, carrying the slabs above and • Anchors act as load bearing and restraint, carrying the slabs above and
restraining the slabs below. restraint, carrying the slabs above and restraining the slabs below.
restraining the slabs below.
29
HA L Anchor Fixing Systems - Installation Detail
Anchor
Variations
1- Through bolt
2- Anchor body
3- Serrated washer
4- Round washer for through bolt
5- Hex nut for through bolt
6- Plastic tube
7- Flanged pin

Elevation view Section A-A Installation details
HA01
L Anchor

HA04
L Anchor
HA01 L Anchor - Product Details
Fdw
For anchoring into
concrete ≥ C20/25
K
Cement grout
Load bearing E.b.
Fws/Fwp
T
Restraining
Plastic tube St L
St=20-50 mm
Technical Details
Product Projection Dead Wind Wind Bolt Size Pin Anchor Anchor
Code Load Pressure Suction Diameter Length Thickness
K (mm) Fdw (N) Fwp (N) Fws (N) E.b. (mm) ø (mm) L (mm) T (mm)
HA01-301 30 36
HA01-351 35 41 2
HA01-401 40 46
100 156 110 M8X80 4
HA01-451 45 51
HA01-501 50 56 2.5
HA01-551 55 61
HA01-302 30 38
HA01-352 35 43 3
HA01-402 40 200 312 219 M8X80 4 48
HA01-452 45 53
HA01-502 50 58
4
HA01-552 55 63
HA01-303 30 38
3
HA01-353 35 43
HA01-403 40 328 5 48
300 468 M8X80
HA01-453 45 53
4
HA01-503 50 58
HA01-553 55 63
HA01-304 30 38 3
HA01-354 35 43
HA01-404 40 48
437 5
HA01-454 45 400 624 M8X80 53 4
HA01-504 50 58
HA01-554 55 63
• Material: Stainless Steel 1.4301 (A2) & 1.4401 (A4). • Other sizes are available for production upon request.
• Table above is prepared according to Eurocode standard. • Bolts are provided separately.
• Loads stated are working resistance loads. • Structural calculation reports are available upon order.
HA01 L Anchor
• Limited adjustability • Suitable for horizontal • Stone thicknesses above 20 mm
Product Code Description Shape A Shape B Shape C
HA01 - 30 1 A
Shape
Dead Load (x10 Kg)
Projection (K mm)
Type
31
HA02 & HA03 L Anchor - Product Details

Fdw For anchoring into
HA02 L Anchor
concrete ≥ C20/25
• Load bearing & restraint.
K
• Projection sizes between 30
and 55 mm. Cement grout
• Loads up to 400 N.
T
• Suitable for horizontal joints. Load bearing E.b.
• Stone thicknesses above
20mm. Fws/Fwp
• Fastened on walls with
expansion bolts.
• Stone installation is made Ø
with a single anchor on each Restraining

side.
Plastic tube St
Shape A L
St=20-50 mm
Technical Details
Product Projection Dead Load Wind Wind Bolt Size Pin Anchor Anchor
Code Pressure Suction Diameter Length Thickness
Shape B
HA02-302 30 38
HA02-352 35 43
HA02-402 40 48
200 312 219 M8X80 4 3
Shape C HA02-452 45 53
HA02-502 50 58
HA02-552 55 63
HA02-304 30 38
HA02 - 30 2 A
HA02-354 35 43
Shape
HA02-404 40 48
Dead Load (x10 Kg)
HA02-454 45 400 624 437 M8X80 6 53 4
Projection (K mm)
Type HA02-504 50 58
HA02-554 55 63
HA03 L Anchor Fdw

For anchoring into
• Load bearing & restraint. concrete C20/25
• Projection sizes between 30 K

and 55 mm.
Cement Grout
• Suitable for horizontal joints. T
Load Bearing
• Stone thicknesses above E.b.
20mm.
Fws/Fwp
expansion bolts. Kr
• Installation is made with kerf T

system where there are slit Restraining
edges in the slabs.
Plastic sleeve St L St > 20mm
Shape A
Technical Details
Product Projection Dead Load Wind Wind Bolt Size Pin Anchor Anchor
Code Pressure Suction Diameter Length Thickness
Shape B
HA03-302 30 32
HA03-352 35 37
3
HA03-402 40 42
Shape C 200 312 219 M8X80 12
HA03-452 45 47
HA03-502 50 52
4
HA03-552 55 57
HA03-304 30 32 3
HA03 - 30 2 A
HA03-354 35 37
Shape
HA03-404 40 42
Dead Load (x10 Kg)
HA03-454 45 400 624 437 M8X80 15 47 4
Projection (K mm)
Type HA03-504 50 52
HA03-554 55 57
HA04 & HA05 L Anchor - Product Details

Fdw
For anchoring into
HA04 L Anchor
concrete ≥ C20/25
• Load bearing & restraint. K
and 180 mm. Cement Grout
Load Bearing
• Suitable for horizontal joints. E.b.
• Stone thicknesses above

20mm. Fws/F wp
T
expansion bolts. Ø
• Adjustability of the projection Restraining
Lp
size is provided with the
adjustable plate. Plastic Tube L
St St=20-50 mm
Shape A
Technical Details
Shape B Product Projec- Min. Max. Dead Wind Wind Bolt Pin Anchor Adj. Adj.
tion Projec- Projec- Load Pressure Suction Size Diameter Length Plate Plate
Code tion tion Length Thickness
K (mm) K - (mm) K + (mm) Fdw (N) Fwp (N) Fws (N) E.b. (mm) ø (mm) L (mm) Lp (mm) T (mm)
HA04-1006 100 85 115 70

Shape C HA04-1206 120 105 135 90
HA04-1406 140 125 155 600 936 655 M12X120 6 110 80 6
HA04-1606 160 145 175 130
HA04-1806 180 165 195 150
HA04 - 100 6 A
HA04-1008 100 85 115 70
Shape
Dead Load (x10 Kg) HA04-1208 120 105 135 90
Projection (K mm) HA04-1408 140 125 155 800 1235 865 M12X120 6 110 80 6
Type HA04-1608 160 145 175 130
HA04-1808 180 165 195 150
HA05 L Anchor Fdw For anchoring into

• Load bearing & restraint. concrete ≥ C20/25
• Projection sizes between 200 K
and 280 mm. Cement Grout
• Suitable for horizontal joints. Load Bearing
• Stone thicknesses above E.b.
20mm. Fws/Fwp
T
expansion bolts. Ø
• Adjustability of the projection
Restraining Lp
size is provided with the
adjustable plate. L
Plastic Tube
St St=20-50 mm
Shape A
Technical Details
Shape B Projec- Min. Max. Dead Wind Wind Bolt Pin Anchor Adj. Adj.
Product
tion Projec- Projec- Load Pressure Suction Size Diameter Length Plate Plate
Code tion tion Length Thickness
K (mm) K - (mm) K + (mm) Fdw (N) Fwp (N) Fws (N) E.b. (mm) ø (mm) L (mm) Lp (mm) T (mm)
HA05-2006 200 185 215 170

Shape C HA05-2206 220 205 235 190
HA05-2406 240 225 255 600 936 655 M12X120 6 210 80 6
HA05-2606 260 245 275 230
HA05 - 200 6 A HA05-2806 280 265 295 250
Shape HA05-2008 200 185 215 170
Dead Load (x10 Kg) HA05-2208 220 205 235 190
Projection (K mm) HA05-2408 240 225 255 800 1235 865 M12X120 6 210 80 6
Type HA05-2608 260 245 275 230
HA05-2808 280 265 295 250
33
HA Anchors - Special Application Details
L anchor with adjustable plate

combined with a wedge
washer instead of serrated
washer. This is chosen in
cases where vertical loads are
too high for the serrated washer
to sustain the no slip feature.
HA04-K L anchor with

adjustable kerfed plates. This
anchor is the same as HA04 L
anchor with the difference of
using kerf connection to stone
instead of a pin connection.
L anchor is produced with three

holes in order to accommodate
a special requirement.
Customized production is
made in any case to fulfil the
special requirement of the
stone application.
HAZ 21 restraint anchor,

designed for the purpose of
installing into insulated walls
more quickly. Insulation is
drilled instead of cut. HAZ 21
anchors are generally used as
restraints and are used for
corbel facade installations.
Special Designs
L anchors are used to install thick L anchors are used to support large semi L anchors used for stone installation
stone slabs around corners. circular stones to forming a massive around column with variations in
column block. stone and projection.
HDM Mortar Anchor Fixing Systems - Introduction
Restraint Anchors
• Direct fixing to concrete and masonry walls with mortar
• Economical & easy fixing HN HG
• Installation at vertical and horizontal joints
• Special design for installing heavy loads at large projection sizes
Load Bearing Anchors

BUN BUG BTN BTG MTN MTG
Installation at horizontal joints with BUG anchors Installation at vertical joints with BTN & HG anchors
Fdw/1 Fdw/1
Fdw/2 Fdw/2
Restraint
Load Bearing
Load Bearing &
Restraint
Installation at vertical joints with BUN & HG anchors

• Suitable for installing high load natural stone slabs at large
projection sizes on to concrete and masonry walls.
• Holes 6mm larger than the anchor width are drilled in the
walls.
• The holes are filled with mortar and anchors are set into mortar
Fdw/1 Fdw/1 bed.
• In horizontal joint installation, slabs are pinned on the

bottom and upper sides. Anchors act as load bearing carrying
half the weight of the slabs above.
Anchors also act as restraint holding the slabs below and

restraining against wind suction and pressure.
Restraint • In vertical joint installation, slabs are pinned at the left and
right sides. Anchors on the bottom are load bearing anchors
Load Bearing
carrying the whole weight of the slab.
Half the weight of the slab on the left and half the weight of the
slab on the right. Anchors on the top are restraint anchors
holding the slabs and restraining against wind suction and
pressure.
35
HDM Mortar Anchor Fixing Systems - Installation Details
Anchor
Variations
Shape A
Shape B
1- Anchor Body
2- Flanged pin
3- Plastic
Installation at horizontal joints Elevation view Section A-A Installation details
Restraint
BUG
Mortar Anchor Load Bearing
Load Bearing

Restraint
HG
Restraint Anchor
Load Bearing
BUN
Mortar Anchor
Load Bearing & Restraint
BUN & BUG Mortar Anchor - Product Details
BUN Mortar Anchor Fdw

For mortaring into
• Load bearing & restraint. concrete ≥ C20/25
and Masonry M12/II
and 240 mm.
• Loads up to 1200 N
BØ
• Three dimensional adjust Fws/Fwp
ability.
• Suitable for vertical joints. Load Bearing
Z
L1
• Stone thicknesses Cement Grout
20-50mm.
• Fastened into concrete St
T
≥C20/25 and Masonry
M12/II. K
Ø St=20-50 mm
Plastic Tube
Shape A (Top View)
Technical Details
Projec- Min. Max. Dead Wind Wind Z Embedded Pin Bore Anchor
Product
tion Projec- Projec- Load Pressure Suction Size Length Diameter Diameter Thickness
Code tion tion
K (mm) K - (mm) K + (mm) Fdw (N) Fwp (N) Fws (N) Z (mm) L1 (mm) ø (mm) Bø (mm) T (mm)
Shape B
BUN-622 220 210 230 600 393 786 22 80 5 34 3
BUN-624 240 230 250 38
BUN-816 160 150 170
BUN-818 180 170 190 32
BUN-820 200 190 210 800 524 1048 22 80 5 4
BUN-822 220 210 230
36
BUN-824 240 230 250
BUN-1016 160 150 170
BUN-1018 180 170 190 32
BUN-1020 200 190 210 1000 655 1310 22 80 6 4
BUN - 6 22 A BUN-1022 220 210 230
Shape BUN-1024 240 230 250
Projection (x10mm)
BUN-1216 160 150 170
BUN-1218 180 170 190
Dead Load (x10 Kg) 36
BUN-1220 200 190 210 1200 818 1636 22 80 6 4
Type BUN-1222 220 210 230
BUN-1224 240 230 250 38
BUG Mortar Anchor

• Projection sizes between 160 Fdw
For mortaring into
and 240 mm. Cement Mortar concrete ≥ C20/25
• Loads up to 600 N. and Masonry M12/II
• Three dimensional
Load Bearing Z
adjustability.
• Suitable for horizontal joints. BØ
Fws/Fwp
• Stone thicknesses 20-50mm. T
• Fastened into concrete
Restraint
≥C20/25 and Masonry Ø
L1
Plastic Tube
M12/II.
Shape A
K St=20-50 mm
St
Shape B Technical Details

Product
Code tion tion
BUG-616 160 150 170 32

BUG-618 180 180 190
BUG-620 200 200 210 600 571 1142 17 80 5 4
34
BUG-622 220 220 230
BUG-624 240 240 250 36
• Table below is prepared according to Eurocode standard.
BUG - 6 22 A
Shape • Other sizes are available for production upon request.
Projection (x10mm) • Structural calculations are available upon order.
Dead Load (x10 Kg)
Type
37
BTN & BTG Mortar Anchor- Product Details
BTN Mortar Anchor

• Load bearing & restraint. Fdw For mortaring into
• Projection sizes between 160 concrete ≥ C20/25
and Masonry M12/II
and 240 mm.
adjustability. BØ
Fws/Fwp
• Suitable for vertical joints.
• Stone thicknesses Cement
Mortar
20-50 mm. Restraint
L1
• Fastened into concrete T
≥C20/25 and Masonry
M12/II. Ø Plastic St
Tube K St=20-50 mm
Shape A
Technical Details
Projec- Min. Max. Dead Wind Wind Embedded Pin Bore Anchor
Product
tion Projec- Projec- Load Pressure Suction Length Diameter Diameter Thickness
Code tion tion
Shape B K (mm) K - (mm) K + (mm) Fdw (N) Fwp (N) Fws (N) L1 (mm) ø (mm) Bø (mm) T (mm)
BTN-416 160 150 170 36 5

BTN-418 180 170 190 38 5
BTN-420 200 190 210 400 260 520 80 5 40 5
BTN-422 220 210 230 6
36
BTN-424 240 230 250 6
BTN-616 160 150 170 39
BTN-618 180 170 190 600 393 786 80 5 41 6
BTN-620 200 190 210 42
BTN - 4 16 A
Shape
Projection (x10mm)
Dead Load (x10 Kg)
Type
BTG Mortar Anchor

For mortaring into
and 240 mm.
Cement Mortar concrete ≥ C20/25
• Loads up to 500 N. and Masonry M12/II
Load Bearing Z
adjustability.
• Suitable for horizontal joints. BØ
Fws/Fwp
• Stone thicknesses T
20-50 mm.
• Fastened into concrete Ø
L1
≥C20/25 and Masonry Restraint
M12/II. Plastic Tube
Shape A K
St=20-50 mm
St
Technical Details
Shape B
Product
Code tion tion
BTG-316 160 150 170 30

BTG-318 180 170 190 5
32
BTG-320 200 190 210 300 393 786 22 80 5
BTG-322 220 210 230
BTG-324 240 230 250 34
6
BTG-516 160 150 170
BTG-518 180 170 190 500 655 1309 22 80 5 36
BTG - 3 16 A BTG-520 200 190 210 38
Shape • Material: Stainless Steel 1.4301 (A2) & 1.4401 (A4).
Projection (x10mm) • Table below is prepared according to Eurocode standard.
Dead Load (x10 Kg) • Loads stated are working resistance loads.
Type • Other sizes are available for production upon request.
MTN & MTG Mortar Anchor - Product Details

Fdw
MTN Mortar Anchor K For mortaring into
• Load bearing & restraint Masonry M12/II
and 180 mm.
• Three dimensional L1
T
adjustability.
• Suitable for vertical joints. Fws/Fwp
BØ
Cement
• Stone thicknesses Grout
20-50 mm. Load bearing
• Fastened into Masonry
M12/II walls with mortar. T
Plastic
Ø Tube
(Top View)
Shape A St
Technical Details
Projec- Min. Max. Dead Wind Wind Embedded Pin Bore Anchor
Product
tion Projec- Projec- Load Pressure Suction Length Diameter Diameter Thickness
Code tion tion
Shape B K (mm) K - (mm) K + (mm) Fdw (N) Fwp (N) Fws (N) L1 (mm) ø (mm) Bø (mm) T (mm)
MTN-4 8 80 70 90 30 5
MTN-414 140 130 140 400 295 589 90 5 34 5
MTN-418 180 170 180 36 6
MTN-6 6 60 50 70 6
34
MTN-612 120 110 130 600 442 884 90 5 6
MTN-620 200 190 210 38 6
MTN-10 8 80 70 80 38 6
MTN-1024 140 130 140 100 737 1473 90 5 40 6
MTN-1018 180 170 190 42 6
MTN - 4 8 A
Shape • Loads stated are working resistance loads.
Projection (x10mm) • Other sizes are available for production upon request.
Dead Load (x10 Kg) • Structural calculations are available upon order.
Type
MTG Mortar Anchor

Fdw
• Load bearing & restraint. K For mortaring into
• Projection sizes between 100 Masonry M12/II
and 200 mm.
Cement Grout
L1
• Three dimensional Load Bearing Z
adjustability. T
• Suitable for horizontal joints.
Fws/Fwp
• Stone thicknesses 20-50 mm. T BØ
• Fastened into Masonry M12/II
walls with mortar. Ø
Restraint
Plastic Tube
Shape A
St
Technical Details
Shape B Product Projec- Min. Max. Dead Wind Wind Z Embedded Pin Bore Anchor
Code tion tion
MTG-310 100 90 110 3

MTG-314 140 130 150 300 442 884 22 90 5 34 4
MTG-316 160 150 170 5
MTG-4 8 80 70 90 34 4
MTG-412 120 110 130 400 589 1179 22 90 5 36 4
MTG-420 200 190 210 40 6
MTG-6 6 60 50 70 38 4
MTG - 3 16 A MTG-610 100 90 110 600 884 1768 22 90 5 38 5
Shape MTG-616 160 150 170 40 6
MTG-8 8 80 70 90 40 5
Projection (x10mm)
MTG-816 160 150 170 800 1179 2357 22 90 5 44 8
Dead Load (x10 Kg) MTG-820 200 190 210 46 8
Type
39
HN & HG Mortar Anchor Restraint - Product Details
HN Mortar Anchor&Restraint L1
• Restraint only. Cement

• Projection sizes between 160 Grout
and 240 mm.
• Wind loads up to 1000 N.
• Three dimensional BØ
Fws/Fwp
adjustability. T
• Suitable for horizontal joints. Restraint
• Stone thicknesses Plastic Tube
Ø
20-50 mm.
≥C20/25 Masonry M12/II Mortaring into
walls with mortar. concrete ≥ C20/25
K
and Masonry M12/II
Shape A St
Technical Details
Product Projec- Min. Max. Wind Wind Embedded Pin Bore Anchor
tion Projec- Projec- Pressure Suction Length Diameter Diameter Thickness
Code
tion tion
Shape B K (mm) K - (mm) K + (mm) Fwp (N) Fws (N) L1 (mm) ø (mm) Bø (mm) T (mm)
HN-1016 160 150 170

HN-1018 180 170 190 21
HN-1020 200 190 210 1000 500 80 5 3
HN-1022 220 210 230 24
HN-1024 240 230 250 26
HN - 10 16 A
Shape
Projection (x10mm)
Dead Load (x10 Kg)
Type
HG Mortar Anchor
• Restraint only. St L1
and 240 mm.

• Wind loads up to 1000 N.
adjustability.
BØ
• Suitable for vertical joints. Fws/Fwp
• Stone thicknesses
20-50 mm. Coment Grout
• Fastened into concrete Restraint
≥C20/25 Masonry M12/II

T
walls with mortar. Mortaring into
concrete ≥ C20/25
Shape A Ø Plastic Tube K and Masonry M12/II
Technical Details
Shape B Product Projec- Min. Max. Wind Wind Embedded Pin Bore Anchor
tion Projec- Projec- Pressure Suction Length Diameter Diameter Thickness
Code
tion tion
K (mm) K - (mm) K + (mm) Fwp (N) Fws (N) L1 (mm) ø (mm) Bø (mm) T (mm)
HG-1016 160 150 170

HG-1018 180 170 190 21
HG-1020 200 190 210 1000 500 80 5 3
HG-1022 220 210 230 24
HG-1024 240 230 250 26
HG - 10 16 A • Loads stated are working resistance loads.
Shape • Other sizes are available for production upon request.
Projection (x10mm) • Structural calculations are available upon request.
Dead Load (x10 Kg)
Type
HSD Mortar Anchor Fixing Systems - Introduction
• Direct fixing to concrete and masonry walls with mortar

• Economical & easy fixing
HSD01 Mortar Anchor HSD02 Mortar Anchor HSD03 Mortar Anchor HSD04 Mortar Anchor HRD01
W. Plate Twisted Head W. Plate & Twisted Mortar Anchor
Installation at Horizontal joints Installation at Horizontal joints Installation at Vertical joints

with HRD01 Anchor with HSD04 with HSD02&03
Fdw/2 Fdw/2 Fdw/2 Fdw/2 Fdw/1 Fdw/1
Load Bearing& Load Bearing& Restraint

Restraint Restraint
Load Bearing
HRD Mortar Anchor Fixing Systems - Product Details
HRD01 Mortar Anchor Fdw

w
• Load bearing & restraint. For mortaring into
concrete ≥ C20/25
• Projection sizes between 35 K and Masonry M12/II
and 75 mm.
Cement Grout
• Loads up to 400 N
L1
• Three dimensional Load Bearing
adjustability. Suitable for
horizontal joints. Fws/FwpF
T
• Stone thicknesses
20-50 mm.
Ø
≥C20/25 and Masonry Restraining L
M12/II.
Plastic Tube St
Shape A St=20-50 mm
Technical Details
Shape B Product Projec- Min. Max. Dead Wind Wind Anchor Dowel Pin Bore Flat
tion Projec- Projec- Load Pressure Suction Length Embedded Diameter Diameter Thickness
Code tion tion Length
K (mm) K - (mm) K + (mm) Fdw (N) Fwp (N) Fws (N) L (mm) L1 (mm) ø (mm) Bø (mm) T (mm)
HRD01-351 35 20 50 135 12 2.5

HRD01-451 45 30 60 145
HRD01-551 55 40 70 100 156 110 155 80 4 14 3
HRD01-651 65 50 80 165
HRD01-751 75 60 90 175
HRD01-352 35 20 50 135
HRD01-452 45 30 60 145 14 3
HRD01-552 55 40 70 200 312 219 155 80 4
HRD01 - 35 1 A HRD01-652 65 50 80 165 16 3.5
Shape HRD01-752 75 60 90 175
Dead Load (x10 kg) HRD01-354 35 20 50 135
Projection (x10 mm) HRD01-454 45 30 60 145
Type HRD01-554 55 40 70 400 624 437 155 80 5 18 4
HRD01-654 65 50 80 165
HRD01-754 75 60 90 175
• Material: Stainless Steel 1.4301 (A2) & 1.4401 (A4).• Table below is prepared according to Eurocode standard.
• Loads stated are working resistance loads. • Other sizes are available for production upon request.
41
HSD Mortar Anchors - Product Details

HSD01 Mortar Anchor Technical Details
Projec- Min. Max. Dead Wind Wind Anchor Dowel Pin Bore Flat
Product
HSD01-352 35 20 50 135 21
HSD01-452 45 30 60 145
HSD01-552 55 40 70 200 312 219 155 90 4 2.5
HSD01-652 65 50 80 165 24
HSD01-752 75 60 90 175
HSD01-354 35 20 50 135 26
HSD01-454 45 30 60 145
HSD01-554 55 40 70 400 624 437 155 90 5 28 2.5
HSD01-654 65 50 80 165 30
HSD01-754 75 60 90 175 32
HSD01-356 35 20 50 135
HSD01-456 45 30 60 145 26
HSD01-556 55 40 70 600 936 655 155 90 6 28 4
HSD01-656 65 50 80 165 30
HSD01-756 75 60 90 175 32

Product
HSD02-352 35 20 50 135 24
HSD02-452 45 30 60 145
HSD02-552 55 40 70 200 312 219 155 90 4 2.5
HSD02-652 65 50 80 165 28
HSD02-752 75 60 90 175
HSD02-354 35 20 50 135 30
HSD02-454 45 30 60 145
HSD02-554 55 40 70 400 624 437 155 90 5 32 2.5
HSD02-654 65 50 80 165 34
HSD02-754 75 60 90 175 36
HSD02-356 35 20 50 135
HSD02-456 45 30 60 145 30
HSD02-556 55 40 70 600 936 655 155 90 6 32 4
HSD02-656 65 50 80 165 34
HSD02-756 75 60 90 175 36

Product
HSD03-352 35 20 50 135
HSD03-452 45 30 60 145
HSD03-552 55 40 70 200 312 219 155 90 4 26 3
HSD03-652 65 50 80 165
HSD03-752 75 60 90 175
HSD03-354 35 20 50 135
HSD03-454 45 30 60 145 24
HSD03-554 55 40 70 400 624 437 155 90 5 4
HSD03-654 65 50 80 165
26
HSD03-754 75 60 90 175
HSD03-356 35 20 50 135
HSD03-456 45 30 60 145
HSD03-556 55 40 70 600 936 655 155 90 6 34 4
HSD03-656 65 50 80 165
HSD03-756 75 60 90 175

Product
HSD04-352 35 20 50 135
HSD04-452 45 30 60 145
HSD04-552 55 40 70 200 312 219 155 90 4 30 3
HSD04-652 65 50 80 165
HSD04-752 75 60 90 175
HSD04-354 35 20 50 135
HSD04-454 45 30 60 145 28
HSD04-554 55 40 70 400 624 437 155 90 5 4
HSD04-654 65 50 80 165
30
HSD04-754 75 60 90 175
HSD04-356 35 20 50 135
HSD04-456 45 30 60 145
HSD04-556 55 40 70 600 936 655 155 90 6 38 4
HSD04-656 65 50 80 165
HSD04-756 75 60 90 175
HMP Sub Channel Fixing Systems - Introduction
• Indirect fixing on to non-load bearing walls or for large projection sizes

• Lower drilling points enable fast installation
• Special design is made for sub channel systems to suit various application requirements.
Channels Sub channel systems

HMPA HMPB HMPC HMPL HMPA-HC2 HMPC-HC1 HMPA-HC3
Channel supports
HCSP1 HCSP2 HCSP3 HCSP4
Channel restraints
HCRS1 HCRS2 HCRS3 HCRS4
HMPA-HC2 Channel System HMPC-HC1 Channel System
Channels supported on to load bearing Vertical channels supported on to load
concrete beams with HCSP2 channel bearing beams with HCSP1 channel
supports using anchor bolts supports using expansion bolts
Horizontal C channels are fixed on to the

Stone installation is made with HZ02 & HRS1
vertical channels with HCC channel
Anchors on to channels with hex bolts
connections with lock nuts sets
Stone installation is made with HZ01

Channels are tied on to walls with HCRS2
Anchors on to channels with lock nuts
Channel restraints to eliminate deflection
hex bolts
43
HMP Sub Channel Systems - Installation Details

Installation at vertical
• Sub channel Joints
Fdw/1 Fdw/1
systems are fixed to
load bearing beams
for support.
• Channels are fixed

on to beams with
channel supports.
• Fixing of channels in
the middle to the wall
1- Through Bolt
2- Channel Support
with channel restraints
3- Plain Washer are made to reduce
4- Washer deflection. Installation at
5- Nut horizontal Joints
6- Bolt Set Fdw/2 Fdw/2
7- Channel Restraint • When installation is
8- Channel at vertical joints, the
9- Anchor set
sub channel system
bears the whole load
of the slabs installed.
• When installation is
at horizontal joints, the
sub channel system
bears half the load of
the slabs installed.
Installation at vertical Joints
HCSP2 Channel Support
HCRS2 Channel Restraint
HMPA U Channel
HZ02 Z Anchor
Installation at horizontal Joints
HCSP1 Channel Support
HCRS1 Channel Restraint
HMPB C Channel
HZ02 Z Anchor
ATS Sub Channel Systems - Product Information

ATS Channel System Elements
HMPS 41/22 & HMPS 41/41 ATS-A ATS-B

Toothed Channel Channel Support Channel Restraint
ATS Fixing System Elements

The ATS Channel system allows the quick and easy installation
of natural stone facades through its adjustable capability and
uncomplicated assembly features.
• The channel system is supported by the ATS-A channel

support brackets.
• ATS-B channel restraint brackets, restrain the channel system

against wind pressure and helps prevent the channel from
buckling.
HZ-00 ATS-HA ATS-TS
• The HMPS toothed channel enables the fixing of the anchors Z Anchor Special Anchor Special Anchor
with hex bolts and lock nuts without the need for drilled holes
and the use of nuts and washers.
• Toothed channel and lock nuts provide vertical load support

after fixing.
ATS-A Channel Support
ATS-B Channel Restraint
ATS-HZ Z Anchor
45
HMP Channels - Product Details
HMPA U Channel Technical Details

Product Dimensions X-X Axis Y-Y Axis
Code
Thickness Width Height IXX (cm4) ZX (cm3) X (mm) IYY (cm4) ZY (cm3) Y (mm)
T (mm) W (mm) H (mm)
HMPA-2.5-40/30 2.50 40.00 30.00 1.57 0.74 20.00 4.21 2.11 8.80
HMPA-2.5-40/40 2.50 40.00 40.00 3.91 1.50 20.00 5.97 2.99 13.84
HMPA-3-35/35 3.00 35.00 35.00 2.83 1.24 17.50 4.27 2.44 12.14
HMPA-3-40/30 3.00 40.00 30.00 1.79 0.85 20.00 4.86 2.43 8.83
HMPA-3-40/40 3.00 40.00 40.00 4.55 1.74 20.00 6.92 3.46 13.93
HMPA-3-50/50 3.00 50.00 50.00 9.68 2.97 25.00 15.04 6.01 17.42
HMPA-4-40/40 4.00 40.00 40.00 5.67 2.19 20.00 8.60 4.30 14.10
HMPA-4-50/50 4.00 50.00 50.00 12.33 3.81 25.00 18.97 7.60 17.65
HMPA-5-50/50 5.00 50.00 50.00 14.68 4.57 25.00 22.40 8.97 17.87
HMPB C Channel Technical Details

Code
HMPB-2.5-28/15 2.50 28.00 15.00 0.33 0.43 14.00 1.43 1.02 7.38
HMPB-3-38/17 3.00 38.00 17.00 0.76 0.82 19.00 4.59 2.42 7.79
HMPB-2.5-41/21 2.50 41.00 21.00 1.32 1.19 20.50 5.71 2.79 9.85
HMPB-3-41/21 3.00 41.00 21.00 1.48 1.33 20.50 6.55 3.19 9.86
HMPC C Channel Technical Details

Code
HMPC-2.5-41/22 2.50 41.00 22.00 1.25 0.99 20.50 5.60 2.72 8.16
HMPC-2.5-41/41 2.50 41.00 41.00 7.92 3.62 20.50 9.40 4.58 19.02
HMPC-3-41/22 3.00 41.00 22.00 1.69 1.43 20.50 6.94 3.40 9.16
HMPC-3-41/41 3.00 41.00 41.00 9.40 4.20 20.50 11.30 5.50 18.80
HMPL L Channel Technical Details

Code
HMPL-2.5-30/30 2.50 30.00 30.00 0.93 0.44 21.22 0.93 0.44 8.78
HMPL-2.5-30/40 2.50 30.00 40.00 1.04 0.39 26.33 2.16 0.39 7.23
HMPL-3-30/30 3.00 30.00 30.00 1.09 0.52 20.79 1.09 0.52 9.21
HMPL-3-40/40 3.00 40.00 40.00 2.88 1.02 28.16 2.88 1.02 11.84
HMPL-3-50/50 3.00 50.00 50.00 6.04 1.69 35.72 6.04 1.69 14.28
HMPL-4-40/40 4.00 40.00 40.00 3.72 1.34 27.79 3.72 1.34 12.21
HMPL-50/50 4.00 50.00 50.00 7.85 2.22 35.40 7.85 2.22 14.60
HMPL-5-50/50 5.00 50.00 50.00 9.57 2.73 35.03 9.57 2.73 14.97
• Material: Stainless Steel 1.4301 (A2) & 1.4401 (A4) and Hot dip galvanized mild steel.
• Tables above is prepared according to values with Ø11 drilled holes.
• Channels can be provided up to 6 metres length.
• Load capacity for wind loads and dead loads needs to be verified with stuctural calculations.
HCSP Channel Supports - Product Details
HCSP1 Channel Support Technical Details

Product Thickness Width Height Forming Slot Hole Slot Hole Hole
Code Dia. Length Dia.
T (mm) W (mm) H (mm) F (mm) S ø (mm) SL (mm) ø (mm)

HCSP1-40 4 40 80 40 11 30 11
HCSP1-60 4 40 90 60 11 30 11
HCSP1-80 5 45 100 80 11 30 11
HCSP1-100 5 45 100 100 11 30 11
HCSP1-120 6 50 100 120 11 30 11
HCSP1-140 6 50 100 140 11 30 11
HCSP1-160 6 50 115 160 11 30 11
HCSP1-180 6 55 115 180 11 30 11
HCSP1-200 6 55 120 200 11 30 11
• Suitable for all type of channels

• Max dead load 2.5 kN
• Max wind load 1.2 kN

Product Thickness Width Height Forming Slot Hole Slot Hole Hole Thr. Rod
Code Dia. Length Dia. Metric Size
T (mm) W (mm) H (mm) F (mm) S ø (mm) SL (mm) ø (mm) MxL (mm)
HCSP2-100 4 160 85 100 11 30 11 M10x110

HCSP2-120 4 160 85 120 11 30 11 M10X130
HCSP2-140 5 160 95 140 11 30 11 M10X150
HCSP2-160 5 160 95 160 11 30 11 M10X170
HCSP2-180 5 180 95 180 11 30 11 M10X190
HCSP2-210 5 180 95 210 11 30 11 M10X220
HCSP2-240 5 180 95 240 11 30 11 M10x240
HCSP2-270 5 180 100 270 11 30 11 M10x280
HCSP2-300 5 180 100 300 11 30 11 M10x310
• Suitable only for HMPA type U channels

Product Thickness Width Height Forming Slot Hole Slot Hole Hole Slot hole
Code Dia. Length Dia. length
T (mm) W (mm) H (mm) F (mm) S ø (mm) SL (mm) ø (mm) SL2 (mm)
HCSP3-70 3 120 50 70 11 25 11 30
HCSP3-90 3 120 50 90 11 25 11 30
HCSP3-110 4 120 50 110 11 25 11 30
HCSP3-130 4 120 50 130 11 25 11 30
HCSP3-150 5 120 50 150 11 25 11 30
HCSP3-170 5 120 50 170 11 25 11 30
HCSP3-190 5 120 50 190 11 25 11 30
HCSP3-210 5 120 60 210 11 25 11 30
HCSP3-230 5 120 60 230 11 25 11 30
• Suitable only for HMPA type U channels & HMPL type L channels

HCSP4-100 3 50 175 100 11 30 11 M10x110

HCSP4-120 3 50 175 120 11 30 11 M10X130
HCSP4-140 4 50 175 140 11 30 11 M10X150
HCSP4-160 4 50 195 160 11 30 11 M10X170
HCSP4-180 4 50 195 180 11 30 11 M10X190
HCSP4-210 5 50 195 210 11 30 11 M10X220
HCSP4-240 5 50 195 240 11 30 11 M10x240
HCSP4-270 5 50 215 270 11 30 11 M10x280
HCSP4-300 5 50 215 300 11 30 11 M10x310
• Material: Stainless Steel 1.4301 (A2) & 1.4401 (A4) and Hot dip galvanized ST37 mild steel.
47
HCRS Channel Restraints - Product Details
HCRS1 Channel Restraint Technical Details

Product Thickness Width Height Forming Slot Hole Slot Hole Hole
Code Dia. Length Dia.
T (mm) W (mm) H (mm) F (mm) S ø (mm) SL (mm) ø (mm)

HCRS1-40 2 40 60 40 9 30 9
HCRS1-60 2 40 60 60 9 30 9
HCRS1-80 3 45 80 80 9 30 9
HCRS1-100 3 45 80 100 9 30 9
HCRS1-120 4 50 100 120 9 30 9
HCRS1-140 4 50 100 140 9 30 9
HCRS1-160 4 50 100 160 9 30 9
HCRS1-180 4 50 100 180 9 30 9
HCRS1-200 4 50 100 200 9 30 9
• Suitable for all type of channels


HCRS2-100 4 160 85 100 11 30 11 M10x110

HCRS2-120 4 160 85 120 11 30 11 M10X130
HCRS2-140 5 160 95 140 11 30 11 M10X150
HCRS2-160 5 160 95 160 11 30 11 M10X170
HCRS2-180 5 180 95 180 11 30 11 M10X190
HCRS2-210 5 180 95 210 11 30 11 M10X220
HCRS2-240 5 180 95 240 11 30 11 M10x240
HCRS2-270 5 180 100 270 11 30 11 M10x280
HCRS2-300 5 180 100 300 11 30 11 M10x310

Product Thickness Width Height Forming Slot Hole Slot Hole Hole Slot hole
Code Dia. Length Dia. length
T (mm) W (mm) H (mm) F (mm) S ø (mm) SL (mm) ø (mm) SL2 (mm)
HCRS3-70 3 40 50 70 11 25 11 30
HCRS3-90 3 40 50 90 11 25 11 30
HCRS3-110 4 40 50 110 11 25 11 30
HCRS3-130 4 40 50 130 11 25 11 30
HCRS3-150 5 40 50 150 11 25 11 30
HCRS3-170 5 40 50 170 11 25 11 30
HCRS3-190 5 40 50 190 11 25 11 30
HCRS3-210 5 40 60 210 11 25 11 30
HCRS3-230 5 40 60 230 11 25 11 30
• Suitable only for HMPA type U channels & HMPL type L channels

HCRS4-100 3 50 175 100 11 30 11 M10x110

HCRS4-120 3 50 175 120 11 30 11 M10X130
HCRS4-140 4 50 175 140 11 30 11 M10X150
HCRS4-160 4 50 195 160 11 30 11 M10X170
HCRS4-180 4 50 195 180 11 30 11 M10X190
HCRS4-210 5 50 195 210 11 30 11 M10X220
HCRS4-240 5 50 195 240 11 30 11 M10x240
HCRS4-270 5 50 215 270 11 30 11 M10x280
HCRS4-300 5 50 215 300 11 30 11 M10x310
• Material: Stainless Steel 1.4301 (A2) & 1.4401 (A4) and Hot dip galvanized ST37 mild steel.
HMP Sub Channel Systems - Application Examples
HMPA-HC2 sub channel HMPB-HC1 sub channel

fixing system : fixing system :
• High load bearing and • Easy to assemble sub

adjustable sub channel channel system.
system.
• Easy to install with
• Fast and easy fixing of uncomplicated elements.
stone slabs.
• Minimum projection size
• Minimum projection size is 110 mm and
is 90 mm and maximum maximum is 250 mm.
is 350 mm.
• Ideal for restoration of
• Ideal for heavy loads facades.
and large projection
sizes. • Anchors are fixed to
channels with hex bolts
• Anchors are fixed to and hex nuts.
channels with hex bolts
and hex nuts.
HCSP2 HCRS2 HMPA HZ02 HRS1 HCSP1 HCRS1 HMPB HZ02

Channel Channel U Channel Z Anchor Restraint Channel Channel Channel Z Anchor
Support Restraint Anchor Support Restraint
ATS sub channel fixing HMPC-HC1H

system : sub channel system :
• Adjustable and easy to • Adjustable sub channel

use sub channel system. system with horizontal
channels.
• Fast and easy fixing of
stone slabs. • Quick adjustability at
horizontal axis.
• Minimum projection size
is 160 mm and maximum • Minimum projection size
projection size is 360 mm. is 150 mm and maximum
is 240 mm.
• Ideal for varying
projection sizes and slab • Ideal for staggered
dimensions. patterned facades.
• Anchors are fixed to • Anchors are fixed to

toothed channels with lock channels with lock nuts
nuts and hex bolts. and hex bolts.
ATS-A ATS-B HMPS ATS-HA HZ-00 HCSP1 HCRS1 HMPC HMPC HZ01
Channel Channel Toothed Special Z Anchor Channel Channel C Channel C Channel Z Anchor
Support Restraint Channel Anchor Support Restraint
49
HMP Channel Systems - Special Application Details
Channel sub frame is

designed to accommodate
the natural stone angular
installation.
Channel system is supported

on to concrete floor and
ceiling forming a false wall for
stone installation.
Customized panels with

stone slabs supported on to
channel sub frame.
Stone installation around

structural steel column.
Channels are used to form a
sub frame for fixing with
adjustable anchors.
Sub frame is formed to

accommodate the facade
movement. Channels provi-
de the means of easy and
fast installation.
Fixing Systems for Reconstructed Stone - Introduction
Fixing systems with aluminium channels are available for the installation of natural stone, ceramics and fibre cement panels. A variety of
systems are available to accommodate the application requirements . Custom designs are also made for special requirements. Three
dimensional adjustability is provided and fast installation is possible due to the light weight of aluminium and the ease of cutting and drilling
on site.
HMP-ALU-U Aluminium Sub Channel System
Aluminium U Channel is supported and

restrained with stainless steel brackets on to
the walls. Stainless steel body 1 anchors are
used for stone installation.
1 Channel support
2 Vert�cal U channel
3 Body anchor
4 Z Anchor
HMP-ALU-AG Aluminium Sub Channel System
Aluminium sub channel system with vertical

and horizontal channels that allow the fixing of
panels from the rear surface using undercut
bolts.
1 Vert�cal alum�n�um channel

2 Hor�zontal alum�n�um channel
6 3 Channel support
4 Agraffe alum�n�um bracket
5 Channel connect�on bracket
6 Channel restra�nt
51
HMP-ALU Aluminium Sub Channel Systems - Application Examples
HMP-ALU-SP/H HMP-ALU-SP
Aluminium Sub Channel Aluminium Sub Channel
System System
• Adjustable sub channel • Easy to assemble sub

system with horizontal channel system with special
channels slotted aluminium channels
• Quick adjustability at • Slots on the channels allow

horizontal axis easy installation of special
type Speed fix anchors.
• Projection sizes up to 350
• Quick and fast installation
mm with self tapping screws.
• Ideal for staggered • Projection sizes of up to

patterned facades 300 mm
• Anchors are fixed to • Ideal for restoration of

channels with lock nuts and facades
hex bolts
• Suitable for installation at

horizontal joints
HCSP5 HCRS5 HMP-ALU-U HMP-AL-RL HZ-00-SP HCSP-6 HCSP-6 HMP-ALU-RL HZ-SP

Channel Channel Aluminium Aluminium Z Anchor Channel Channel Channel Z Anchor
Support Restraint Channel Channel Support Restraint
HMP-ALU-P HMP-ALU-AG/K Aluminium

Aluminium Sub Channel Sub Channel System
System
• Channel system formed
• Channel system formed with vertical and horizontal
with vertical and horizontal aluminium channel grid
aluminium channel grid
• Used stone panels width
• Used for thin panels such mm 2 cm thickness that
as ceramic, HPL, fibre have slotted kerf openings
cement and stone panels on the edge
• Projection sizes up to 250 • Projection sizes up to 300

mm mm
• Panels are installed with • Panels are installed with

undercut bolts and special kerf shaped aluminium
brackets that are set on the brackets that are fixed on to
vertical channels using the the horizontal aluminium
hang on method channels with hang on
method
HCSP3-AL HMP-ALU-T HMP-ALU-P HM-AG-P HCSP3-AL HCRS1 HMPC HM-AG-K

Channel T Vertical Horizontal Special Channel Channel C Channel Special
Support Channel Channel Bracket Support Restraint Bracket
Fixing Systems For Heavy Corbel Stones - Product Range
Fixing systems for the installation of high load natural stone or reconstructed stone are available in a variety of types and size ranges. The
actual system proposal will be made according to the technical requirements of the project. The use of these fixing systems is for high load
coping and cornice stones. Load bearing and restraint anchors are used to install the slabs on to different wall backings using a variety
of attachment methods.
Application Examples
Heavy Load Bearing Anchors

HMS-UP
HMCS-SB/P HMCS-DB HAMF
Restraint Anchors
HA-RST HA-RST/K HA-RST/K B HAZ21
Periscope Anchors
HPC1 HPC2 HPC3 HPC4
53
Fixing Systems For Heavy Corbel Stones - Introduction
Load Bearing Anchors
Fixing options Fixing with Expansion bolts

Heavy Duty brackets used for
load bearing are fixed on to load
bearing concrete walls. The two
main methods that are usually
used for attachments are either
by anchor bolts or anchor
channels.
Fixing with Cast in channels
Both anchor channels and
anchors bolts specified accord-
ing to the load requirements of Expansion
joint
the projects and must be
structurally verified according to
the loads concerned on the
Projection K
project.
Heavy Duty brackets have

limited adjustability to take the
Projection K Stone Thickness St
irregularities of the walls. An
accepted method is use of shims
to adjust the projection sized by
up to 5 mm.
Greater adjustability can be

achieved by special design as
illustrated on the diagram on the
right. An adjustable plate can be
adapted to adjust in and out the
distance of the projection size.
Restraining Brackets
There are many systems to be

used for restraining the stone
slabs that are supported on a
corbel system. Channel systems
can be used as they are suitable
to be fixed on commonly used
steel sections.
Restraint anchors or wall ties

can be easily fixed on to the
channel at desired position
which enables greater flexibility
and easiness in installing the
slabs.
Restraint brackets are used for

restraining stone slabs directly
on to wall backings. There are
various types of brackets that
can be used for quick and easy
installation.
Depending on the cavity and the

existence of insulation on the
wall, different type of restraint
brackets are preferred for
installation.
HCA Corner Anchors - Product Details
• For fixing small slabs on to supported facade slabs.

• Used for reveal, column, soffit and sill slabs.
• Slabs can be assembled in the work shop for faster installation on site.
• Special drilling is required on the slabs, details of which are shown at the bottom of the page.
HCA01 Corner Anchor HCA02 Corner Anchor HCA03 Corner Anchor
HCA01 Application HCA02 Application HCA03 Application

Reveal slabs can be connected to the Soffit slabs can be connected to the This anchor is used to fasten two slabs
supported slabs at columns. In this supported slabs at parapets. In this together at corners. The disk is inserted at
instance HCA01 corner anchors are instance only HCA02 corner anchors a split edge on the slab. A special bolt is
used as load bearing and HCA02 are are used as restraint. fixed between the anchor and the disk
used as restraint. which firmly connects the slabs together.
Technical Details
Product Vertical Adjustable Straight
Reveal Size Wind Load
Code Load Arm Pin
StxWxL cm (N) (N) (mm) (mm)

3(4)x10x45 38(50) 40
HCA02 3(4)x15x60 76(100) 50 M8x45 ø5x80
3(4)x20x75 130(170) 60
Technical Details
Product Vertical Adjustable Straight
Reveal Size Wind Load
Code Load Arm Pin
StxWxL cm (N) (N) (mm) (mm)

3(4)x10x45 38(50) 40
HCA01 3(4)x15x60 76(100) 50 M8x45 ø5x80
3(4)x20x75 130(170) 60
Special Drilling for HCA01 & HCA02 Corner Anchors

Special drilling is done to the slabs at the upper face and at the back. The drilling must be done
precisely as shown on the illustration. The adjustable arm inserted from the back of the stone
meets the pin which is inserted from the edge surface of the stone.
55
HAZ Accessories - Product Details

HAA Adjustable Arm Technical Detail
Product Distance
Flat length Flattening Pin Stone
Metric
RevealSize Length Between
Code Size Thickness Diameter Thickness
Edge & Hole
M (mm) L (mm) AF (mm) T (mm) ø (mm) St (mm) A (mm)
HAA-8/50 8 50 A+6 3 4 20 12-13
HAA-8/60 8 60 A+6 3 4 25 14-16
HAA-8/70 8 70 A+6 3 4 30 16-17
HAA-10/50 10 50 A+8 3.5 5 40 22-24
HAA-10/60 10 60 A+8 3.5 5 50 26-29
HAA-10/70 10 70 A+8 3.5 5
HAA-10/80 10 80 A+8 3.5 5
HAA-12/50 12 50 A+8 4.5 5 T
HAA-12/60 12 60 A+8 4.5 5
HAA-12/70 12 70 A+8 4.5 5 AF
HAA-12/80 12 80 A+8 4.5 5 A
HAA-14/50 14 50 A+8 5.5 6
HAA-14/60 14 60 A+8 5.5 6 Ø
HAA-14/70 14 70 A+8 5.5 6
HAA-14/80 14 80 A+8 5.5 6
HAA-16/50 16 50 A+8 6 6
HAA-16/60 16 60 A+8 6 6
HAA-16/70 16 70 A+8 6 6 L
HAA-16/80 16 80 A+8 6 6
Type B : With Welded Pin Type C : With Welded Plate Type D : With Welded Plate & Pins Type E : With Welded Shim
HFP Flanged Pin Technical Details HSW Serrated Washer Technical Details
Product Flange Product Thick-
Diameter Length Height Width Length
Code Diameter Code ness
ø (mm) L (mm) Fø (mm) T (mm) H (mm) W (mm) L (mm)

HFP-4/50 4 50 5 HSW-22307 2.5 22 30 ø7
HFP-5/60 5 60 6 HSW-22309 2.5 22 30 ø9
HFP-5/70 5 70 6 HSW-263411 3 26 34 ø11
HFP-6/70 6 70 7 HSW-263413 3 26 34 ø13
HTP Traced Pin Technical Details HPW Plain Washer Technical Details
Product Trace Product Thick-
Diameter Length Height Width Length
Code Height Code ness
ø (mm) L (mm) TH (mm) T (mm) H (mm) W (mm) L (mm)

HTP-5/70 5 70 5.2 HPW-22307 2.5 22 30 ø7
HTP-6/75 6 75 6.2 HPW-22309 2.5 22 30 ø9
HPW-263411 3 26 34 ø11
HPW-263413 3 26 34 ø13
HSP Straight Pin Technical Details HMLN Lock Nut Technical Details
Product Product Thick-
Diameter Length Height Width Metric
Code Code ness
Hole
ø (mm) L (mm) T (mm) H (mm) W (mm) M (mm)
HSP-4/60 4 60 HMLN-6 6 20 34 M6
HSP-5/60 5 60 HMLN-8 8 20 34 M8
HSP-5/70 5 70 HMLN-10 9 20 34 M10
HSP-6/70 6 70 HMLN-12 10 20 34 M12
HUP U Shaped Pin Technical Details HSM Shim Plate Technical Details
Product Product Thick- Slot
Diameter Height Width Height Width
Code Code ness Hole
ø (mm) L (mm) W (mm) T (mm) H (mm) W (mm) ø x SL

HUP-4/50 4 20 50 HSM-4030-7 2 40 30 7x20
HUP-5/50 5 25 50 HSM-4030-9 2 40 30 9x25
HUP-6/50 6 30 50 HSM-4050-11 3 40 50 11x25
HSM-4050-13 4 40 50 13x30
HCP Capped Pin Technical Details HPT Plastic Tube Technical Details
Product Cap Product Inner Outer
Diameter Length Length
Code Diameter Code Diameter Diameter
ø (mm) øC (mm) L (mm) In. ø (mm) Ou. ø (mm) L (mm)

HCP-4/35 4 6 35 HPT-4 4.5 6 30
HCP-5/40 5 7 40 HPT-5 5.5 7 40
HCP-6/45 6 8 45 HPT-6 6.5 8 40
• Material : Stainless Steel 1.4301 (A2) & 1.4401 (A4). Material for Plastic Tube: Polyacetal.
HB Anchor Bolts - Product Details
HB01 Sleeve Bolt
Application
For fastening fixtures to
concrete strength class
C20/25 & solid
concrete block walls.
Available in
Stainless Steel EN
1.4301 & 1.4401 (AISI
304 & AISI 316) and
E.galvanized Mild
Steel.
Technical Details Working Resistance (kN)

Product Code Example Product Bolt Size Sleeve Drill Hole Drill
Min. Max.
Fixture Max Bolt
Concrete C 20/25
Embed- Fixture Blockwork Concrete
Code Size Dia. Length Hole Dia. Torque Length
Wall Wall
HB01 - 6 / 80 ment Thickness
(mm) (mm) D (mm) HT (mm) E min. (mm) Smax (mm) D1 (mm) Mdmax(Nm) L (mm) Pullout S hear Pullout Shear
Length HB01-6/80 M6X80 ø8x60 8 55 45 10 9 7 80 2.50 0.84 4.29 5.43
Diameter HB01-8/80 M8X80 ø10x60 10 55 45 10 11 15 80 2.89 1.04 6.85 9.89
Type HB01-10/80 M10X80 ø12x60 12 55 45 10 13 30 80 3.00 1.24 7.72 15.60
HB01-12/100 M12X100 ø16x78 16 75 65 10 17 45 100 3.20 1.40 8.00 16.10
HB03 Through Bolt
Application
C20/25 & solid
Available in
Stainless Steel EN
1.4301 & 1.4401 (AISI
304 & AISI 316) and Technical Details Working Resistance (kN)
E.galvanized mild steel. Min. Max.
Product Bolt Size Drill Hole Drill Fixture Max Bolt Thread C 20/25 Concrete
Embed- Fixture Wall
Code Dia. Length Hole Dia. Torque Length Length
ment Thickness
(mm) D (mm) HT (mm) E min. (mm) Smax (mm) D1 (mm) Mdmax(Nm) L (mm) LG (mm) Pullout Shear
Product Code Example HB03-8/80 M8X80 8 65 47 23 9 13 80 30

HB03-8/100 M8X100 8 65 47 43 9 13 100 45 4.11 6.50
HB03-8/120 M8X120 8 65 47 63 9 13 120 65
HB03 - 8 / 80 HB03-10/90 M10X90 10 70 65 17 11 25 90 35
HB03-10/110 M10X110 10 70 65 37 11 25 110 45 6.47 9.70
Length HB03-10/130 M10X130 10 70 65 57 11 25 130 65
Diameter HB03-12/110 M12X110 12 95 80 15 13 40 110 35
Type HB03-12/135 M12X135 12 95 80 40 13 40 135 40 9.64 12.40
HB03-12/145 M12X145 12 95 80 50 13 40 145 40
HB05 Shell Bolt
Application
C20/25 & solid
Available in
Stainless steel EN
1.4301 & 1.4401 (AISI
304 & AISI 316)

Product Code Example Product Bolt Size Shell Drill Hole Drill
Min. Max.
Fixture Max Bolt
Concrete C 20/25
Embed- Fixture Blockwork Concrete
Code Size Dia. Length Hole Dia. Torque Length
Wall Wall
HB05 - 6 / 80 ment Thickness
(mm) (mm) D (mm) HT (mm) E min. (mm) Smax (mm) D1 (mm) Mdmax(Nm) L (mm) Pullout S hear Pullout Shear
Length HB05-6/80 M6X80 ø10X59 10 65 40 15 7 10 80 3.50 3.30 4.20 3.30

Diameter HB05-8/80 M8X80 ø12X44 12 80 45 20 9 20 80 4.10 6.70 6.15 6.70
Type HB05-10/100 M10X100 ø15X50 15 90 55 30 11 40 100 5.20 11.00 9.50 11.00
HB05-12/120 M12X120 ø18X65 18 105 65 30 13 75 120 6.05 12.15 11.95 17.50
57
HB Expansion Bolts - Product Details
HB06 Drop in Bolt
Application
concrete walls.
Available in
Stainless Steel EN
1.4301 & 1.4401 (AISI
304 & AISI 316) and
E.galvanized mild steel.

Min. Max. Screw in C 20/25
Product Bolt Size Shell Drill Hole Drill Fixture Max
Embed- Fixture Depth Concrete
Product Code Example Code Size Dia. Length
ment Thickness
Hole Dia. Torque
Min/Max Wall
HB06 - 6 (mm) (mm) D (mm) HT (mm) E min. (mm) Smax (mm) D1 (mm) Mdmax(Nm) Sd (mm) Pullout Shear
HB06-6 M6X20 ø8x25 8 28 25 11 7 4 6/10 2.00 1.78

HB06-8 M8X25 ø10x30 10 33 30 13 9 8 11/17 3.20 3.30
M. Size HB06-10 M10X30 ø12x40 12 43 40 17 11 15 13/19 4.35 3.90
Type HB06-12 M12X35 ø14x50 14 53 50 18 13 35 15/21 6.00 6.80
HB07 Anchor Stud
Application
concrete walls.
Available in
Stainless Steel EN
1.4301 & 1.4401 (AISI
304 & AISI 316) and
E.galvanized Mild
Steel.

Min. Max. Bolt C 20/25
Product Bolt Size Drill Hole Drill Fixture Max
Embed- Fixture Length Concrete
Product Code Example Code Dia. Length
ment Thickness
Hole Dia. Torque
Wall
HB07- 8 / 110 (mm) D (mm) HT (mm) E min. (mm) Smax (mm) D1 (mm) Mdmax(Nm) L (mm) Pullout Shear
HB07-8/110 M8X110 10 82 80 14 9 7 110 8.80 10.20

Length
HB07-10/130 M10X130 12 92 90 21 11 15 130 12.30 15.60
Diameter HB07-12/160 M12X160 14 115 110 28 13 25 160 18.30 22.00
Type
HB11 Undercut bolt

D
Application Mdmax
For Facade
Applications
Du
Available in
Stainless Steel EN HAZ-MC-11 HAZ-DB-11
1.4301 & 1.4401 (AISI HB11 undercut drill machine HB11 drill bit
304 & AISI 316)
Advantages E min
HT
• Higher pull out values
• Lower bending
moment on panel
• No appearence of
fixing at joints Technical Details Working Resistance (kN)
Product Min. Max. Hard Soft
Product Code Example Bolt Stone Drill Hole Drill
Embed- Fixture
Fixture Max Bolt Thread
Code Size Thickness Dia. Length Hole Dia. Torque Length Length Granite Marble
HB11 - 20 ment Thickness
(mm) St (mm) D/Du (mm) HT (mm) E min. (mm) Smax (mm) Df (mm) Mdmax(Nm) L (mm) (mm) Pullout Shear Pullout Shear
HB11-20 M6X27 20 8/11 12.50 11.50 5 9 5 24 14.5 1.20 1.20 1.00 1.00
ST Thick. 10/13 21.00 20.00 2.50 2.20 2.50 2.20
HB11-30 M8X37 30 5 9 12 34 14.5
Type HB11-40 M8X47 40 10/13 31.00 30.00 5 9 12 39 14.5 2.80 2.50 2.80 2.50
A safety factor of 3 is taken for mean ultimate failure loads.
References
Project : Conference Palace Hotel - Abu Dhabi

Contractor : Turner Construction
Installation Area : 160.000 m2
Project : Al Nahyan Masque - Abu Dhabi

Contractor : Six Construct International
Project : Museum of Islamic Arts - Doha

Contractor : Baytur Construction
Project : Bibliotheca Alexandria Library - Alexandria Project : Texas Engineering University - Doha
Contractor : Balfour Beatty and Arab Contractors JV Contractor : Midmac Contracting
Installation Area : 40.000 m2 Installation Area : 60.000 m2
Project : Sabanci University - Istanbul Project : Is Bank Towers - Istanbul

Contractor : Koray Construction Contractor : Tepe Construction
Installation Area : 160.000 m2 Installation Area : 45.000 m2
59
References
Project : Demir Bank Project : Yapi Kredi Project : Zorlu Holding Project : Istek Vakif Project : Tekfen Tower Project : Garanti Bank
Location : Istanbul Location : Istanbul Location : Istanbul Location : Istanbul Location : Istanbul Location : Istanbul
Project : Admo Apco Project : Emirates Towers Project : Fairmont Hotel Project : Zadgo Gasco Project : Trade Center
Location : Abu Dhabi Location : Dubai Location : Dubai Location : Abu Dhabi Location : Abu Dhabi
Project : American Embassy Project : American Embassy Project : American Embassy Project : American Embassy
Location : Istanbul Location : Kingston Location : Astana Location : Yerevan
Project : Usadba Center Project : Tax Office Project : Lazurnaya Project : Gasprom Project : Riverside Hotel Project : Ritz Carlton Hotel
Location : Moscow Location : Moscow Location : Sochi Location : Moscow Location : Moscow Location : Moscow
Project : Hilton Hotel Project : Kingdom Trade Project : Medinah Project : Four Seasons Hotel Project : The Fund Project : Mauritius Hotel
Location : Jeddah Location : Riyadh Location : Jeddah Location : Cairo Location : Abu Dhabi Location : Mauritius
HAZ Metal is certified with integrated management
HAZ Metal Sanayi ve Ticaret A.S.
systems by TUV SUD for ISO 9001 & OHSAS 18001
is a member of HAZ Group of Companies
HAZ PAZARLAMA İÇ & DIŞ TİC. A.Ş. HAZ METAL SANAYİ VE TİCARET A.Ş. HAZ METAL DEUTSCHLAND GmbH
İçerenköy Mh. Çayır Cd. Özce Center Şehit Er Çıracı Caddesi No. 10 Leonhard Karl Strasse 29
No:3 K:12 34752 Ataşehir Akçay Sanayi Bölgesi 31200 İskenderun 97877 Wertheim, Germany
İstanbul, TÜRKİYE Hatay, TÜRKİYE Tel : +49 (0) 9342 93590
Tel : +90 (0) 216 410 72 06 Tel : +90 (0) 326 626 20 50 Fax : +49 (0) 9342 935929
Fax : +90 (0) 216 410 71 41 Fax : +90 (0) 326 626 20 45 www.hazmetal.de
www.hazpazarlama.com www.hazmetal.com info@hazmetal.de
hazpazarlama@hazgrp.com info@hazmetal.com
HAZ INTERNATIONAL LTD. HAZ MARBLE INDUSTRY & TRADE LLC HAZ ASIA PACIFIC PTE LTD
154 Great North Road Hatfield First Gulf Building Corniche Street Blk 22 Woodlands Link #01-65
Herts. AL9 5JN England 2nd Floor, Flat No. 202 P.O. Box 5721 Singapore 738734
Tel : +44 (0) 1707 - 260 180 Abu Dhabi, United Arab Emirates Tel: +65 6853 7681
Fax : +44 (0) 1707 - 260 190 Tel : +971 (0) 2 622 07 00 Fax: +65 6752 9582
www.hazuk.co.uk Fax : +971 (0) 2 622 17 00 www.hazapac.com
haz@hazuk.co.uk www.hazuae.ae info@hazapac.com
hazuae@hazmarbleuae.ae
HAZ EGYPT LTD HAZ MARBLE QATAR WLL HAZ RUS LTD
Villa no.29-Third Floor.St.no.270 P.O.BOX 31296 C-Ring road 117036, Ul, Profsoyuznaya Dom 3 (office 531)
New Maadi, Cairo, Egypt Doha, Qatar Moscow, Russian Federation
Tel : +20 (2) 2447 09 85 Tel : +974 (4) 467 26 13-47 Tel : +7 (926) 672 31 84
www.hazeg.com Fax : +974 (4) 467 47 49 info@hazrus.ru
info@hazeg.com www.hazqatar.com www.hazrus.ru
hazdoha@hazqatar.com
Always at the forefront of fixing technology, HAZ METAL has earned a reputation as the leaders in fixing systems
innovation and is regarded as the one to follow. HAZ METAL fixing systems of today become the standard of
tomorrow.
HAZ METAL combines the very latest international technology with its own research and development team to
establish a technical excellence within the industry. HAZ METAL readily embraces the responsibility of a major
producer and shares its expertise with problem solving solutions.

01 HAZ Metal Stone Fixing Systems Brochure 2

Uploaded by

Copyright:

Available Formats

01 HAZ Metal Stone Fixing Systems Brochure 2

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

01 HAZ Metal Stone Fixing Systems Brochure 2

Uploaded by

Copyright:

Available Formats

Stone Fixing Systems

Your Fixing Systems Specialist

Stone Fixing Systems

Natural Stone Fixing Systems - Overview

Introduction Mission Statement

The company’s objective is to assist and advise its clients in

Technical Service Production Capacity

Stone Fixing Systems - Overview

HZ Z Anchor Fixing System

HAZ Metal proposes and specially designs fixing systems

Fixing to concrete with bolt

• Fixing to concrete with bolts.

Direct fixing to concrete or

Fixing to concrete with mortar HSD Mortar Anchor Fixing System

• Fixing to masonry with mortar.

Indirect fixing to load

Stone Fixing Systems - Overview

Application examples for bolt anchors

To fasten anchors on to isolated walls, the

Application examples of profile systems

Technical Design & Engineering

Our technical department receives the necessary technical information of the

HAZ Metal provides the necessary technical documentation for submittal to

Finite element stress analysis is implemented for complex structures where

Reference is made to the following standards:

BS 8298 • Design and installation of natural stone cladding

DIN 18 516 • Cladding for ventilated walls

ASTM C1242 -12 • Standard guide for stone attachment systems

EN 1990 Basis of Structural Design. Structural Analysis and

Wall Structure Natural Stone Material

Structure - Edge Spacing Anchor Pins

Applied Loads - (Actions)

Range on the stone; Tmin ºC < t ºC < tmax ºC

Wall Backing Group of Bolts

Concrete wall Masonry wall Block work wall

Direct fixing to concrete

Direct fixing to concrete

Load Bearing Restraint

Support anchor in horizontal joint Restraint anchor in horizontal joint

FDW = Dead load ds = Density of stone t = Thickness of stone

Support anchor in vertical joint Restraint anchor in vertical joint

HZ Z Anchor Fixing Systems - Introduction

HZ01 HZ02 HZ05 Z Anchor HZ07 HZ08 Z Anchor HRS1

Three dimensional adjustability

1) Vertical adjustment is 2) Adjustment of the 3) Adjustment of the

Installation at horizontal joints Installation at vertical joints

Load Bearing & Load

• Recommended projection size between 45 mm to 135 mm and loads up to 800 N.

• Three - dimensional adjustability allows quick and easy installation.

HZ Z Anchor Fixing Systems - Installation Detail

Installation at horizontal joints

HZ02 Z Anchor Load Bearing

Installation at vertical joints

HRS01 Restraint Anchor

HZ01 Z Anchor - Product Details

Fws/Fwp Drilled hole may be

• Material: Stainless Steel 1.4301 (A2) & 1.4401 (A4).

HZ02 Z Anchor - Product Details

Fws/Fwp Drilled hole may be