Optimization

Data Communication & Computer Networks : Signal Lec.
Notes on Phase
Looking at Figure 3.5, we can say that

1. A sine wave with a phase of 0° starts at time 0 with a zero amplitude. The
amplitude is increasing.
2. A sine wave with a phase of 90° starts at time 0 with a peak amplitude. The
amplitude is decreasing.
3. A sine wave with a phase of 180° starts at time 0 with a zero amplitude. The
amplitude is decreasing.
Prepared By: Eng. Omar M. Hussien University of Anbar / College of Computer 1

Data Communication & Computer Networks : Signal Lec.8
Time and Frequency Domains
A sine wave is comprehensively defined by its amplitude, frequency, and phase. We

have been showing a sine wave by using what is called a time-domain plot. The time-
domain plot shows changes in signal amplitude with respect to time (it is an
amplitude-versus-time plot). Phase is not explicitly shown on a time-domain plot.
To show the relationship between amplitude and frequency, we can use what is
called a frequency-domain plot. A frequency-domain plot is concerned with only the
peak value and the frequency. Changes of amplitude during one period are not
shown.
Figure below shows a signal in both the time and frequency domains.

Composite Signals
So far, we have focused on simple sine waves. Simple sine waves have many
applications in daily life. We can send a single sine wave to carry electric energy
from one place to another. For example, the power company sends a single sine wave
with a frequency of 60 Hz to distribute electric energy to houses and businesses.
If we had only one single sine wave to convey a conversation over the phone, it
would make no sense and carry no information. We would just hear a buzz.
A composite signal is made of many simple sine waves.
A single frequency sine wave is not useful in data communications;
we need to send a composite signal, a signal made of many simple sine waves.
In the early 1900s, the French mathematician Jean-Baptiste Fourier showed that
any composite signal is actually a combination of simple sine waves with different
frequencies, According to Fourier analysis, any composite signal is a combination of
simple sine waves with different frequencies, amplitudes, and phases.

A composite signal can be periodic or nonperiodic. A periodic composite signal

can be decomposed into a series of simple sine waves with discrete frequencies that
have integer values (1, 2, 3, and so on). A nonperiodic composite signal can be
decomposed into a combination of an infinite number of simple sine waves with
continuous frequencies, frequencies that have real values.
If the composite signal is periodic, the decomposition gives a series of signals with
discrete frequencies; if the composite signal is nonperiodic, the decomposition gives
a combination of sine waves with continuous frequencies.
Example 3.8
Figure 3.9 shows a periodic composite signal with frequency f, this type of signal is
not typical of those found in data communications. The analysis of this signal can
give us a good understanding of how to decompose signals.
Figure 3.10 shows the result of

decomposing the above signal in both the time and frequency domains.

Time domain
figure (3.10)
The amplitude of the sine wave with frequency f is almost the same as the peak
amplitude of the composite signal. The amplitude of the sine wave with frequency 3f
is one-third of that of the first, and the amplitude of the sine wave with frequency 9f
is one-ninth of the first. The frequency of the sine wave with frequency f is the same
as the frequency of the composite signal; it is called
the fundamental frequency, or first harmonic. The sine wave with frequency 3f has a
frequency of 3 times the fundamental frequency; it is called the third harmonic. The
third sine wave with frequency 9f has a frequency of 9 times the fundamental
frequency; it is called the ninth harmonic.
Bandwidth
The range of frequencies contained in a composite signal is its bandwidth. The

bandwidth is normally a difference between two numbers. For example, if a
composite signal contains frequencies between 1000 and 5000, its bandwidth is 5000
- 1000, or 4000.
The bandwidth of a composite signal is the difference between the highest and the
lowest frequencies contained in that signal.
Figure 3.12 shows the concept of bandwidth.
The figure depicts two composite signals, one periodic and the other nonperiodic.
The bandwidth of the periodic signal contains all integer frequencies between 1000
and 5000 (1000, 1001, 1002, ...). The bandwidth
of the nonperiodic signals has the same range, but the frequencies are continuous.
Example 3.10
If a periodic signal is decomposed into five sine waves with frequencies of 100, 300,
500, 700, and 900 Hz, what is its bandwidth? Draw the spectrum, assuming all
components have a maximum amplitude of 10 V.

Solution:
Let fh be the highest frequency, fl the lowest frequency, and B the bandwidth. Then
B =fh - fl = 900 - 100 =800 Hz
The spectrum has only five spikes, at 100, 300, 500, 700, and 900 Hz (see Figure
3.13).
Example 3.11
A periodic signal has a bandwidth of 20 Hz. The highest frequency is 60 Hz. What is
the lowest frequency? Draw the spectrum if the signal contains all frequencies of the
same amplitude.
Solution:
Let fh be the highest frequency, fz the lowest frequency, and B the bandwidth. Then
B =fh - fz  20 =60 – fz  fz = 60 – 20 = 40 Hz
The spectrum contains all integer frequencies. We show this by a series of spikes
(see Figure 3.14).

3.3 DIGITAL SIGNALS
In addition to being represented by an analog signal, information can also be

represented by a digital signal. For example, a I can be encoded as a positive voltage
and a 0 as zero voltage. A digital signal can have more than two levels. In this case,
we can send more than 1 bit for each level. Figure 3.16 shows two signals, one with
two levels and the other with four.
Figure 3.16 Two digital signals: one with two signal levels and the other with four
signal levels

We send 1 bit per level in part a of the figure and 2 bits per level in part b of the
figure. In general, if a signal has L levels, each level needs log L bits.
Example 3.16
A digital signal has eight levels. How many bits are needed per level? We calculate
the number of bits from the formula
Number of bits per level = log 8 = 3
Each signal level is represented by 3 bits.
Bit Rate
Most digital signals are nonperiodic, and thus period and frequency are not
appropriate characteristics. Another term-bit rate (instead of frequency)-is used to
describe digital signals. The bit rate is the number of bits sent in Is, expressed in bits
per second (bps). Figure 3.16 shows the bit rate for two signals.
Example 3.18
Assume we need to download text documents that have of 100 pages . What is the
required bit rate of the channel?
Solution:
A page is an average of 24 lines with 80 characters in each line. If we assume that
one character requires 8 bits, the bit rate is
100 x 24 x 80 x 8 =1,636,000 bps =1.636 Mbps
Bit Length
The bit length is the distance one bit occupies on the transmission medium.
Bit length = propagation speed x bit duration

Digital Signal as a Composite Analog Signal

Based on Fourier analysis, a digital signal is a composite analog signal. The
bandwidth is infinite, as you may have guessed. We can intuitively corne up with this
concept when we consider a digital signal. A digital signal, in the time domain,
comprises connected vertical and horizontal line segments. A vertical line in the time
domain means a frequency of infinity (sudden change in time); a horizontal line in
the time domain means a frequency of zero (no change in time). Going from a
frequency of zero to a frequency of infinity (and vice versa) implies all frequencies in
between are part of the domain.
Fourier analysis can be used to decompose a digital signal. If the digital signal is
periodic, which is rare in data communications, the decomposed signal has a
frequency domain representation with an infinite bandwidth and discrete frequencies.
If the digital signal is nonperiodic, the decomposed signal still has an infinite
bandwidth, but the frequencies are continuous. Figure 3.17 shows a periodic and a
nonperiodic digital signal and their bandwidths.

Transmission of Digital Signals

The previous discussion asserts that a digital signal, periodic or nonperiodic, is a
composite analog signal with frequencies between zero and infinity. For the
remainder of the discussion, let us consider the case of a nonperiodic digital signal,
similar to the ones we encounter in data communications. The fundamental question
is, How can we send a digital signal from point A to point B? We can transmit a
digital signal by using one of two different approaches: baseband transmission or
broadband transmission (using modulation).
1- Baseband Transmission
Baseband transmission means sending a digital signal over a channel without
changing the digital signal to an analog signal.
2- Broadband Transmission (Using Modulation)

Broadband transmission or modulation means changing the digital signal to an
analog signal for transmission.
Medium Bandwidth and Significant Bandwidth:

A transmission medium has a limited bandwidth which mean that it can transfer only
a some range of frequencies. A transmission medium with a particular bandwidth is
capable of transmitting only digital signals whose significant bandwidth is less than
the bandwidth of the medium. If a signal is sent on a transmission medium whose
bandwidth is less than the required significant bandwidth, the signal may be so
distorted that it is not recognizable at the receiver.

Medium Bandwidth and Data Rate (Channel Capacity)
The significant bandwidth of a signal increases with bit rate. This means when the bit
rate is increased, we have wider significant bandwidth, and consequently we need
medium with wider bandwidth to transfer that signal. The maximum bit rate a
transmission medium can transfer is called channel capacity of the medium.for
example , a normal telephone line with a bandwidth of 3000 Hz is capable of
transferring up to 20000 bps, but other factors can decrease this rate.

Optimization

Uploaded by

Copyright:

Available Formats

Optimization

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Optimization

Uploaded by

Copyright:

Available Formats

Data Communication & Computer Networks : Signal Lec.

Looking at Figure 3.5, we can say that

Prepared By: Eng. Omar M. Hussien University of Anbar / College of Computer 1

Time and Frequency Domains

A sine wave is comprehensively defined by its amplitude, frequency, and phase. We

Prepared By: Eng. Omar M. Hussien University of Anbar / College of Computer 2

Prepared By: Eng. Omar M. Hussien University of Anbar / College of Computer 3

A composite signal can be periodic or nonperiodic. A periodic composite signal

Figure 3.10 shows the result of

Prepared By: Eng. Omar M. Hussien University of Anbar / College of Computer 4

The range of frequencies contained in a composite signal is its bandwidth. The

Prepared By: Eng. Omar M. Hussien University of Anbar / College of Computer 6

Prepared By: Eng. Omar M. Hussien University of Anbar / College of Computer 7

3.3 DIGITAL SIGNALS

In addition to being represented by an analog signal, information can also be

Prepared By: Eng. Omar M. Hussien University of Anbar / College of Computer 8

Prepared By: Eng. Omar M. Hussien University of Anbar / College of Computer 9

Digital Signal as a Composite Analog Signal

Prepared By: Eng. Omar M. Hussien University of Anbar / College of Computer 10

Transmission of Digital Signals

2- Broadband Transmission (Using Modulation)

Medium Bandwidth and Significant Bandwidth:

Prepared By: Eng. Omar M. Hussien University of Anbar / College of Computer 11

Medium Bandwidth and Data Rate (Channel Capacity)

Prepared By: Eng. Omar M. Hussien University of Anbar / College of Computer 12

You might also like