Service Manual

DEH-3130R/X1N/EW

ORDER NO.

CRT2418

HIGH POWER CD PLAYER WITH RDS TUNER

DEH-3130R DEH-3100R-B
X1N/EW

X1N/EW

DEH-3100R
Model No. CX-958 Order No. CRT2423

X1N/EW

- This service manual should be used together with the following manual(s):
Mech. Module Remarks S8.1 CD Mech. Module:Circuit Description, Mech.Description, Disassembly

CONTENTS
1. 2. 3. 4. 5. 6. SAFETY INFORMATION ............................................2 EXPLODED VIEWS AND PARTS LIST .......................3 BLOCK DIAGRAM AND SCHEMATIC DIAGRAM ...10 PCB CONNECTION DIAGRAM ................................28 ELECTRICAL PARTS LIST ........................................38 ADJUSTMENT..........................................................44 7. GENERAL INFORMATION .......................................48 7.1 DIAGNOSIS ........................................................48 7.1.1 TEST MODE ..............................................48 7.1.2 DISASSEMBLY .........................................52 7.2 PARTS .................................................................56 7.2.1 IC................................................................56 7.2.2 DISPLAY ....................................................63 8. OPERATIONS AND SPECIFICATIONS.....................64

PIONEER CORPORATION

4-1, Meguro 1-Chome, Meguro-ku, Tokyo 153-8654, Japan PIONEER ELECTRONICS SERVICE INC. P.O.Box 1760, Long Beach, CA 90801-1760 U.S.A. PIONEER ELECTRONIC [EUROPE] N.V. Haven 1087 Keetberglaan 1, 9120 Melsele, Belgium PIONEER ELECTRONICS ASIACENTRE PTE.LTD. 253 Alexandra Road, #04-01, Singapore 159936

C PIONEER CORPORATION 1999

K-ZZD. OCT. 1999 Printed in Japan

DEH-3130R,3100R-B,3100R

- CD Player Service Precautions

1. For pickup unit(CXX1285) handling, please refer to"Disassembly"(see page 52). During replacement, handling precautions shall be taken to prevent an electrostatic discharge(protection by a short pin). 2. During disassembly, be sure to turn the power off since an internal IC might be destroyed when a connector is plugged or unplugged. 3. Please checking the grating after changing the service pickup unit(see page 44).

1. SAFETY INFORMATION
This service manual is intended for qualified service technicians; it is not meant for the casual do-it-yourselfer. Qualified technicians have the necessary test equipment and tools, and have been trained to properly and safely repair complex products such as those covered by this manual. Improperly performed repairs can adversely affect the safety and reliability of the product and may void the warranty. If you are not qualified to perform the repair of this product properly and safely; you should not risk trying to do so and refer the repair to a qualified service technician. 1. Safety Precautions for those who Service this Unit. When checking or adjusting the emitting power of the laser diode exercise caution in order to get safe, reliable results. Caution: 1. During repair or tests, minimum distance of 13cm from the focus lens must be kept. 2. During repair or tests, do not view laser beam for 10 seconds or longer. 2. A CLASS 1 LASER PRODUCT label is affixed to the bottom of the player. 3. The triangular label is attached to the mechanism unit frame.

CLASS 1 LASER PRODUCT

4. Specifications of Laser Diode Specifications of laser radiation fields to which human access is possible during service. Wavelength = 800 nanometers

DEH-3130R,3100R-B,3100R

2. EXPLODED VIEWS AND PARTS LIST

2.1 PACKING
2 3 6 5 4

12

11

8
13

10

NOTE:
- Parts marked by * are generally unavailable because they are not in our Master Spare Parts List. - Screws adjacent to mark on the product are used for disassembly.

(1) PACKING SECTION PARTS LIST

Mark No. Description * 1 2 3 4 5 6 7 8-1 8-2 8-3 Cord Assy Accessory Assy Screw Handle Bush Polyethylene Bag Polyethylene Bag Owners Manual Owners Manual Owners Manual Part No. CDE6238 CEA2397 CBA1002 CNC5395 CNV3930 E36-615 CEG-162 CRD3073 CRD3074 CRD3075 Mark No. Description * * 8-4 8-5 8-6 8-7 9 10 11 12 13 Installation Manual Passport Warranty Card Polyethylene Bag Case Assy Carton Contain Box Protector Protector Part No. CRD3076 CRY1013 CRY1157 CEG1116 CXB3520
See Contrast table(2) See Contrast table(2)

CHP2251 CHP2252

DEH-3130R,3100R-B,3100R

(2) CONTRAST TABLE DEH-3130R/X1N/EW, DEH-3100R-B/X1N/EW and DEH-3100R/X1N/EW are constructed the same except for the following:
Part No. DEH-3100R-B/X1N/EW DEH-3100R/X1N/EW CHG3883 CHG3881 CHL3883 CHL3881

Mark No. Symbol and Description DEH-3130R/X1N/EW 10 Carton CHG3882 11 Contain Box CHL3882

- Owner's Manual, Installation Manual

Model DEH-3130R/X1N/EW DEH-3100R-B/X1N/EW DEH-3100R/X1N/EW Part No. CRD3073 CRD3074 CRD3075 CRD3076 Language English, Spanish German, French Italian, Dutch English, Spanish, German, French, Italian, Dutch

DEH-3130R,3100R-B,3100R

2.2 EXTERIOR

DEH-3130R,3100R-B,3100R

(1) EXTERIOR SECTION PARTS LIST

Mark No. Description 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 Screw Screw Screw Screw IC(IC551) Cable Cord Assy Resistor Transistor(Q981,991) Cap Fuse(10A) Holder Cover Spacer Earth Plate Insulator Insulator Tuner Amp Unit Screw Screw Screw Connector(CN551) Antenna Cable(CN502) Pin Jack(CN431) Terminal(CN501) Connector(CN951) Connector(CN681) Connector(CN651) Holder Holder Holder Holder Insulator Heat Sink FM/AM Tuner Unit Holder Chassis Unit Button Spring Part No. BMZ26P120FMC BSZ26P060FMC BSZ30P060FMC BSZ30P120FMC Mark No. Description 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 Spring Spring Bracket Holder Cover Panel Arm Arm Arm Screw Case Unit Detach Grille Assy Screw Button(DETACH) Button(1-6) Button(SOURCE) Button(+) Button(-) Button(F) Button(A) Button(EQ) Button(EJECT) Button(BAND) Spring Cover Lighting Conductor Lighting Conductor Housing Keyboard Unit LCD Connector(CN1801) Holder Sheet Lighting Conductor Connector Grille Sub Assy Part No. CBH2367 CBH2208 CNC6791 CNC8042 CNM6276
See Contrast table(2)

PAL005A CDE6160 CDE6238 RS1/2PMF102J 2SD2396 CNS1472 CEK1136 CNC6798 CNC8367 CNM4913 CNC8368 CNM6006 CNM6224

CNV4692 CNV4728 CNV5576 IMS20P030FZK CXB4033

See Contrast table(2)

BPZ20P100FZK
See Contrast table(2)

CAC6239 CAC6241
See Contrast table(2) See Contrast table(2) See Contrast table(2) See Contrast table(2)

CWM6841 ASZ26P080FMC BPZ26P080FMC BSZ26P160FMC CDE5996 CDH1254 CKB1028 CKF1059 CKM1299 CKS2227

CAC6247 CAC6248
See Contrast table(2)

CBH2210
See Contrast table(2)

CNV5909 CNV5910 CNV5918

See Contrast table(2) See Contrast table(2)

CKS3581 CNC7533 CNC8130 CNC8041 CNC8043 CNM5967 CNR1506 CWE1500 CNC7532

See Contrast table(2)

CKS3580 CNC8468 CNM6435 CNV5908 CNV6051

See Contrast table(2)

86 CD Mechanism Module(S8.1) CXK5201 87 Screw ISS26P055FUC

CAC4836 CBH1835

DEH-3130R,3100R-B,3100R

(2) CONTRAST TABLE DEH-3130R/X1N/EW, DEH-3100R-B/X1N/EW and DEH-3100R/X1N/EW are constructed the same except for the following:
Part No. DEH-3100R-B/X1N/EW CXB4709 CNS5188 CXB4723 CAC5789 CAC6242 CAC6243 CAC6244 CAC6245 CAC6249 CNS5622 CWM6797 CAW1572 CXB5252

Mark No. 42 51 61 63 66 67 68 69 72 74

Symbol and Description Chassis Unit Panel Detach Grille Assy Button(DETACH) Button(+) Button(-) Button(F) Button(A) Button(BAND) Cover

DEH-3130R/X1N/EW CXB4711 CNS5340 CXB4722 CAC5929 CAC6559 CAC6560 CAC6561 CAC6562 CAC6578 CAC5794 CWM6796 CAW1570 CXB5251

DEH-3100R/X1N/EW CXB4710 CNS5188 CXB4721 CAC5789 CAC6242 CAC6243 CAC6244 CAC6245 CAC6249 CNS5622 CWM6795 CAW1570 CXB5250

78 Keyboard Unit 79 LCD 85 Grille Sub Assy

DEH-3130R,3100R-B,3100R

2.3 CD MECHANISM MODULE

DEH-3130R,3100R-B,3100R

- CD MECHANISM MODULE SECTION PARTS LIST

Mark No. Description 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 Control Unit Connector(CN802) Connector(CN801) Connector(CN701) Connector(CN101) Screw Screw Screw(M2x3) Screw(M2x5) Screw Screw(M2x4) Washer Washer Washer Spring Spring Spring Spring Spring Spring Spring Spring Spring Spring Spring Spring Spring Spring Bracket Spring Connector Connector Shaft Screw(M2.6x6) Frame Frame Lever Arm Bracket Spacer Sheet Part No. CWX2411 CKS2192 CKS2193 CKS2773 CKS3486 BMZ20P030FMC BSZ20P040FMC CBA1077 EBA1028 CBA1243 CBA1362 CBF1037 CBF1038 CBF1060 Mark No. Description 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 Ball Belt Roller Arm Arm Arm Arm Guide Guide Gear Gear Guide Damper Arm Arm Arm Guide Guide Guide Clamper Gear Motor Unit(M1) Screw Unit Chassis Unit Gear Unit Arm Unit Motor Unit(M2) Lever Unit Arm Unit Motor Unit(M3) Arm Unit Bracket Unit Screw Screw Washer Pickup Unit(Service)(P8) Screw PCB Photo-transistor(Q1, 2) Damper Lack Spring Part No. CNR1189 CNT1086 CNV4509 CNV6037 CNV5247 CNV5248 CNV5249 CNV5254 CNV5255 CNV5257 CNV5256 CNV6176 CNV6010 CNV6096 CNV6031 CNV6211 CNV6012 CNV5510

CBH2079 CBH2117 CBH2314 CBH2110 CBH2282 CBH2318 CBH2324 CBH2118 CBH2161 CBH2163 CBH2189 CBH2249 CBH2260 CBH2262 CNC8568 CBL1369 CDE5531 CDE5532 CLA3304 CBA1458 CNC8565 CNC8749 CNC7546 CNC8663 CNC8567 CNM3315 CNM6659

CNV5751 CNV6013 CNV5813 CXB2190 CXB4726 CXB4797 CXB4728 CXB5753 CXB2195 CXB4730 CXB4731 CXB2562 CXB4732 CXB4795 JFZ20P025FMC JGZ17P025FZK YE20FUC CXX1285 IMS26P030FMC CNX2982 CPT230SX-TU CNV6011 CNV6014 CBH2315

DEH-3130R,3100R-B,3100R

3. BLOCK DIAGRAM AND SCHEMATIC DIAGRAM

3.1 BLOCK DIAGRAM
A
A
ANTENNA 1 2 CN502 27 38 39 42 44 46 63 69 70

TUNER AMP UNIT

Q524 Q525 Q542 Q540

FM/AM TUNER UNIT

FM FRONT END Q3 FM/AM 1ST IF 10.7MHz T51 Q51 CF51 CF52 CF53
25 32

FM MPX
24

TMUTE

IC 2 PM4008A
34 33 41 44 11 12 13 46

19

Q701 RDS DECODER

20 24 fm/AM VDD

ANT1 TV

ANT2 TV

RF TV

22

MIXER.IF AMP DET IC 1 PML002A

35 33 32 45 55 57

54 78 65 71

COMP LDET

21 18

IC 701 PM4009A
11 X501 12

Q201 Q204
28

CF202

61 74

75

EEPROM AM RF Q202 AM 2ND IF 450kHz

VDD CE2 CE1 NL1 3 NL1 CK SL NL2 4 PDIO VCC 25 FMSD 2 SD DI/DO SDBL 8 SDBW 5 6

IC 3 BR9010FV

4 3

PDIO

PCE2

PCE1

CK

LOCL

SYS+B

VDD

PICKUP UNIT(SERVICE)(P8) D CONTROL UNIT

LD MD
LD+ MD CN101 14 5 97 PD A+C/F B+D/E 24 FOP TOP X201 23

Q101
98 LD L_OUT 16

SL

Q401

22 10 14

12 15 16

13

CN701 8 17

CN681 LOUT

HOLOGRAM UNIT FOCUS ACT TRACKING ACT

FO+ TO+ 4 3

IC 201 UPD63711GC

SP601 ALARM BUZZER

IC 301 BA5985FM
16

RF-AMP, DSP, SERVO, DAC

TD/FD SD/MD 39

CD DRIVER

FOP 18 TOP

HOME
4

SPINDLE MOTOR

M
CN801

12 11

SOP SOM

S801 HOME

C
CARRIAGE MOTOR

1 2

14

LOADING MOTOR

3 4 CN802 3 1

COP 13 COM 10 LOP 9 LOM

FWD REV MUTE

1 28 21

CDLOAD CDEJET CONT

6 5 11

19 20 14

CDLOAD CDEJET CONT

EJTSNS DSCSNS CLAMP

22 23 21 24

3 2

EJTSNS DSCSNS CLAMP

SELECT SENSE
2

VD D803 D802 D801 S802 CLAMP VD

Q991
1 B.U

DISC SENSE

+5V REGULATOR
VDD 4

E PHOTO

UNIT(S8)

IC 701 BA05SFP
1

IN

Q992
CD5VON 7 18 VDCONT

10 1 2 3 4

DEH-3130R,3100R-B,3100R

A
36 88 tmute ldet CN431

REAR L CH
29

Q431
FM/AM

SYSTEM CONTROLLER IC 601(1/2) PE5139A

NL1

76

38 74 77 99 97 32 98 PDIO 94 30

SD SL SDBW TUNPCE TUNPCK TUNPCE2 TUNPDO TUNPDI LOCL VST VCK VDT

Q434

Q973
VDD B.U B.U

BACKUP FUSE 10A 2 1

B
BACK UP GND

IN1_L

POWER AMP ELECTRONIC VOLUME/ SOURCE SELECTOR

23 FL RL 10 11 14 FL 12 RL FL FL+ RL RL+ 9 11 10 12

IN2_L

IC 451 PML003AM

IC 551 PAL005A

21 3 5

FL FL+ RL RL+

MUTE 22

STBY 4

B.REM 25 B.REM 5

B.REM

Q551 MUTE Q971

100 PEE asens bsens ASENS 92 ACC 4 ACC B.U

SYSPW

Q921
93 TELMUTE TELMUTE TEL MUTE 7

BSENS

DRSYS TELMUTE

1 2

59 58 53

SYSPW CDLOAD CDEJET CONT

C
RR FR FL RL RR + FR + FL + RL +

SYSTEM CONTROLLER IC 601(2/2) PE5139A

BACK UP

SYSPW MUTE 28

B. REM

78 79 64

EJTSNS DSCSNS

Q921
SYS+B

Q982
B.U

KEYBOARD UNIT

GND ACC

CLAMP

CN651 DSENS 52 8 1

CN1801 DSENS

SWVDD

78 95 96 RESET RESET 11 1 8 9

23

AVCC VDD 56 KYDT VDCONT DPDT 3 4 6 5 KYDT DPDT

LCD

RESET IC 631 S80735ANDZI

VDD

Q652
B.U GRNILM 54 CD5VON 20 GRN

GRN

KEY CONTROLLER AND LCD DRIVER IC 1801 PD6294A

Q653

D
KEY MATRIX
11 X1901 13

11 5 6 7 8

DEH-3130R,3100R-B,3100R

3.2 OVERALL CONNECTION DIAGRAM(GUIDE PAGE)

Note: When ordering service parts, be sure to refer to EXPLODED VIEWS AND PARTS LIST or ELECTRICAL PARTS LIST.

A
A-a A-b

A-a
Large size SCH diagram

TUNER AMP UNIT

A-a

A-b

Guide page

A-a

A-b

Detailed page

FM(100%) : -15.5dBs AM(30%) : -26dBs

FM : -16.5dBs AM : -27dBs S-CD : 0dBs

SOURCE SELECTOR/ ELECTRONIC VOLUME

1 5 6

3 2

FM/AM TUNER UNIT

SYSTEM CONTROLLER

ANTENNA CABLE

DSP-201M-S00B

VD REGULATOR

RDS DECODER

CD MECHANISM MODULE

NOTE : Symbol indicates a resistor. No differentiation is made between chip resistors and discrete resistors. Symbol indicates a capacitor. No differentiation is made between chip capacitors and discrete capacitors. The > mark found on some component parts indicates the importance of the safety factor of the part. Therefore, when replacing, be sure to use parts of identical designation.

Decimal points for resistor and capacitor fixed values are expressed as : 2.2 2R2 0.022 R022

D E

S-CD : 4.4dBs

12

A
1

DEH-3130R,3100R-B,3100R

A-b
MUTE REAR PREOUT
FM : 5.84dBs AM : -2.66dBs S-CD : 9.74dBs

RESET

FM : 6.6dBs AM : -1.9dBs S-CD : 10.5dBs

POWER AMP
FM : 32dBs AM : 24dBs S-CD : 36dBs

>CEK1136

VDD REGULATOR
ERA15-02VH ERA15-02VH ERA15-02VH

1K(1/2W)

BACK UP SENSE
4

ACC SENSE
3

8V REGULATOR
4 3 ERA15-02VH 2 1 5 6 ERA15-02VH

1K(1/2W)

D
TELEPHONE MUTE
RR FR FL RL RR + FR + FL + RL +

ILLUMINATION POWER SUPPLY

BACK UP

B. REM
GND ACC

KEYBOARD UNIT
5 6 7

13

D A C

14

A-a A-b

DEH-3130R,3100R-B,3100R

FM/AM TUNER UNIT

A-a
FM : -16.5dBs AM : -27dBs S-CD : 0dBs

1
SOURCE SELECTOR/ ELECTRONIC VOLUME
1 5 6 3 2 4

TUNER AMP UNIT

1

2
4 5 6 7

FM(100%) : -15.5dBs AM(30%) : -26dBs

3 4

4
SYSTEM CONTROLLER

SYSTEM CONTROLLER

ANTENNA CABLE

DSP-201M-S00B

D E

CD MECHANISM MODULE

5
8 9

VD REGULATOR
10

6
RDS DECODER
Decimal points for resistor and capacitor fixed values are expressed as : 2.2 2R2 0.022 R022

NOTE : Symbol indicates a resistor. No differentiation is made between chip resistors and discrete resistors. Symbol indicates a capacitor. No differentiation is made between chip capacitors and discrete capacitors. The > mark found on some component parts indicates the importance of the safety factor of the part. Therefore, when replacing, be sure to use parts of identical designation.

11

7 C

12

S-CD : 4.4dBs

C
KEYBOARD UNIT

DEH-3130R,3100R-B,3100R

A-a
B A

15

A-a A-b

D A C

16

A-a A-b

DEH-3130R,3100R-B,3100R

A-b
MUTE RESET
FM : 6.6dBs AM : -1.9dBs S-CD : 10.5dBs

1
POWER AMP
FM : 32dBs AM : 24dBs S-CD : 36dBs

REAR PREOUT
FM : 5.84dBs AM : -2.66dBs S-CD : 9.74dBs

ERA15-02VH

9
1K(1/2W)

BACK UP SENSE
6 4

10

ACC SENSE
2 3

ERA15-02VH

5 6

ERA15-02VH

5
>CEK1136

VDD REGULATOR
ERA15-02VH

6
4

8V REGULATOR
3 ERA15-02VH 2 1

1K(1/2W)

11

7
TELEPHONE MUTE
BACK UP

12

ILLUMINATION POWER SUPPLY

B. REM
GND ACC

DEH-3130R,3100R-B,3100R

A-b

RR FR FL RL -

RR + FR + FL + RL +

17 B C A

A-a A-b

DEH-3130R,3100R-B,3100R

3.3 FM/AM TUNER UNIT

A

FM/AM TUNER UNIT

Mark None F0 F65 F125 A0 A74 A125

Band FM FM FM AM AM AM

Input Level 0dBf 65dBf 125dBf 0dB 74dB 125dB

KV1410(23)

KV1410(23)

DAN217U

18

B
1

DAN217U

DEH-3130R,3100R-B,3100R

KV1410(23)

B
8

19

DEH-3130R,3100R-B,3100R

3.4 KEYBOARD UNIT

C
A

KEYBOARD UNIT

CN651

5 3 1

6 4 2

5 3 1

6 4 2

5 3 1

6 4 2

5 3 1

6 4 2

5 3 1

6 4 2

5 3 1

6 4 2

5 3 1

6 4 2

5 3 1

6 4 2

5 3 1

6 4 2

6 5 4

3 2 1

6 5 4

3 2 1

6 5 4

3 2 1

C
5 3 1 6 4 2 5 3 1 6 4 2

6 5 4

3 2 1

5 3 1

6 4 2

5 3 1

6 4 2

5 3 1

6 4 2

20

C
1

DEH-3130R,3100R-B,3100R

: DEH-3130R/X1N/EW, 3100R/X1N/EW : DEH-3100R-B/X1N/EW

D1809,1810 D1811 D1812,1813 S1801-1806,1808-1812,1816-1818 S1807,1813,1814,1819 R1806,1808

DEH-3130R/X1N/EW CL220D CL170DCD CL170DCD CSG1114 CSG1117 390

DEH-3100R-B/X1N/EW CL220SRCTS CL170SRCD CL170SRCD CSG1135 CSG1133 270

DEH-3100R/X1N/EW CL220PGC CL170PGCD CL170PGCD CSG1112 CSG1107 390

C
8

21

DEH-3130R,3100R-B,3100R

3.5 CD MECHANISM MODULE

A

D
PICKUP UNIT (SERVICE)(P8)

CONTROL UNIT

CN101

RF-AMP, SE

PHOTO UNIT(S8)
Q1 CPT230SX-TU Q2 CPT230SX-TU

CN802

SPINDLE MOTOR

M3 CXB2562 CARRIAGE MOTOR

M1 CXB2190

LOADING MOTOR

CD DRIVER
M2 CXB2195

CN801

22

D E

BA05SFP

5V REGULATOR
3 4

DEH-3130R,3100R-B,3100R

SWITCHES: CONTROL UNIT S801 : HOME SWITCH.....ON-OFF S802 : CLAMP SWITCH....ON-OFF The underlined indicates the switch position.

MP, SERVO, DSP, DAC, LPF

CN701

CN681

23

DEH-3130R,3100R-B,3100R
Note:1. The encircled numbers denote measuring pointes in the circuit diagram. 2. Reference voltage REFO:2.5V 1 CH1: RFI 1V/div. 0.5ms/div. 2 CH2: MIRR 5V/div. Test mode: Tracking open 1 CH1: RFI 1V/div. 0.5ms/div. 2 CH2: MIRR 5V/div. Normal mode: The defect part passes 800m

- Waveforms
1 RFI 0.5V/div. 0.5s/div. Normal mode: play

REFO REFO REFO REFO REFO

3 CH1: FD 0.5V/div. 0.2s/div. 4 CH2: FO+ 2V/div. Test mode: No disc, Focus close

3 CH1: FD 0.5V/div. 0.2s/div. 5 CH2: FOK 2V/div. Normal mode: Focus close

6 CH1: FE 0.5V/div. 1ms/div. 7 CH2: XSI 2V/div. Normal mode: Focus close

REFO REFO

REFO

REFO REFO REFO GND

8 CH1: TE 0.5V/div. 0.5ms/div. 9 CH2: TD 0.5V/div. Test mode: 32 tracks jump (FWD)

8 CH1: TE 0.5V/div. 0.5ms/div. 9 CH2: TD 0.5V/div. Test mode: Single jump (FWD)

8 CH1: TE 0.5V/div. 5ms/div. 9 CH2: TD 0.5V/div. Test mode: 100 tracks jump (FWD)

REFO

REFO

REFO

REFO

REFO

REFO

6 CH1: FE 0.1V/div. 3 CH2: FD 0.2V/div. Normal mode: Play

20ms/div.

3 CH1: FD 0.5V/div. 0.5s/div. 0 CH2: MD 1V/div. Normal mode: Focus close (12cm)

3 CH1: FD 0.5V/div. 0.5s/div. 0 CH2: MD 1V/div. Normal mode: Focus close (8cm)

REFO REFO

REFO

REFO

REFO

REFO

24

DEH-3130R,3100R-B,3100R

8 CH1: TE 0.2V/div. 9 CH2: TD 0.2V/div. Normal mode: play

20ms/div.

8 CH1: TE 0.5V/div. 5ms/div. ! CH2: SD 0.5V/div. TEST mode: 100 Tracks jump(FWD)

0 MD

0.5V/div.

0.1s/div.

Normal mode: Play (12cm)

REFO REFO REFO

REFO

REFO

0 MD 1V/div. Normal mode: Long Search (12cm)

10ms/div.

@ EFM

1V/div.

5s/div.

Normal mode: play

8 CH1: TE 1V/div. 2ms/div. # CH2: TEC 1V/div. Test mode: Focus close Tracking open

REFO REFO REFO REFO GND

8 CH1: TE 0.5V/div. 0.2s/div. 6 CH2: FE 0.5V/div. Normal mode: AGC after focus close

$ PLCK

2V/div.

0.5s/div.

% SCKO

2V/div.

1s/div.

Normal mode: play

Normal mode: play

REFO

REFO

REFO GND

REFO GND

^ Dout

2V/div.

10s/div.

& LRCK

2V/div.

20s/div.

* VD

5V/div.

50ms/div.

Normal mode: play

Normal mode: play

Normal mode: No disc

GND REFO GND REFO GND

25

DEH-3130R,3100R-B,3100R

( CH1: R OUT 1V/div. 0.2ms/div. ) CH2: L OUT 1V/div. Normal mode: Play (1kHz 0dB)

6 CH1: FE 0.2V/div. 1ms/div. 3 CH2: FD 0.5V/div. Normal mode: During AGC

8 CH1: TE 0.2V/div. 1ms/div. 9 CH2: TD 0.5V/div. Normal mode: During AGC

REFO REFO REFO

REFO

REFO

REFO

1 CH1: RFI 1V/div. 0.5ms/div. CH2: HOLD 5V/div. Normal mode: The defect part passes 800m(B.D)

3 CH1: FD 0.5V/div. 0.5ms/div. CH2: HOLD 5V/div. Normal mode: The defect part passes 800m(B.D)

9 CH1: TD 0.1V/div. 0.5ms/div. CH2: HOLD 5V/div. Normal mode: The defect part passes 800m(B.D)

REFO

REFO

REFO

REFO

REFO

REFO

26

DEH-3130R,3100R-B,3100R

27

DEH-3130R,3100R-B,3100R

4. PCB CONNECTION DIAGRAM

A

4.1 TUNER AMP UNIT

NOTE FOR PCB DIAGRAMS
1. The parts mounted on this PCB include all necessary parts for several destination. For further information for respective destinations, be sure to check with the schematic diagram. 2. Viewpoint of PCB diagrams

A TUNER AMP UNIT

Connector

Capacitor

SIDE A
B
P.C.Board Chip Part

SIDE B

CN701

CORD ASSY

C
28

CN1801

A
1

DEH-3130R,3100R-B,3100R

SIDE A

IP BUS IN

SUB WOOFER/ REAR PREOUT

L ch R ch

ANTENNA CABLE

A
8

29

DEH-3130R,3100R-B,3100R

A
A

TUNER AMP UNIT

30

A
1

DEH-3130R,3100R-B,3100R

SIDE B
A

A
8

31

DEH-3130R,3100R-B,3100R

4.2 FM/AM TUNER UNIT

SIDE A
A

32 1 2 3 4

FM/AM TUNER UNIT

DEH-3130R,3100R-B,3100R

SIDE B
A

FM/AM TUNER UNIT

33 1 2 3 4

D A C

34

4.3 KEYBOARD UNIT

DEH-3130R,3100R-B,3100R

P.EQ

C
EJECT FUNC BAND AUDIO 1 2 3 4 5 6 TA,TI, PROG PTY, DISP CLOCK

KEYBOARD UNIT

VOL UP

P.EQ+

VOL DOWN

SOURCE

SIDE A
4

DEH-3130R,3100R-B,3100R

SIDE B
A

KEYBOARD UNIT

CN651

C
4

35

D A C

36

D
PICKUP UNIT(SERVICE)(P8) M1 CARRIAGE MOTOR M2 LOADING MOTOR
HOME

CONTROL UNIT

DEH-3130R,3100R-B,3100R

4.5 CD MECHANISM MODULE

D E
M3 SPINDLE MOTOR

PHOTO UNIT(S8)

CN681

SIDE A

3 2 1

CN802

DEH-3130R,3100R-B,3100R

SIDE B
A
CLAMP

CONTROL UNIT

37

DEH-3130R,3100R-B,3100R

5. ELECTRICAL PARTS LIST

NOTES: - Parts whose parts numbers are omitted are subject to being not supplied. - The part numbers shown below indicate chip components. Chip Resistor RS1/_S___J,RS1/__S___J Chip Capacitor (except for CQS.....) CKS....., CCS....., CSZS.....
=====Circuit Symbol and No.===Part Name --- ----------------------------------------------Part No. ------------------------=====Circuit Symbol and No.===Part Name --- ----------------------------------------------L L L TH X X BZ AR 702 921 951 601 601 701 601 501 Inductor Ferri-Inductor Choke Coil 600H Thermistor Radiator 12.58291MHz Crystal Resonator 3.648MHz FM/AM Tuner Unit Buzzer Part No. ------------------------LAU100K LAU2R2K CTH1221 CCX1031 CSS1402 CSS1447 CWE1500 CPV1050 DSP-201M-S00B

A
IC IC IC IC IC Q Q Q Q Q Q Q Q Q Q Q Q Q Q Q Q Q Q Q Q Q Q D D D D D D D D D D D D D D D L L L L L L L L

Unit Number : CWM6841 Unit Name : Tuner Amp Unit

451 551 601 631 701 431 434 502 507 524 525 540 541 542 551 601 651 652 653 701 921 971 973 981 982 991 992 651 654 655 656 921 931 932 951 952 971 972 973 974 981 992 501 504 506 601 619 621 651 701 IC IC IC IC IC Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Diode Diode Network Diode Network Diode Network Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Ferri-Inductor Ferri-Inductor Inductor Inductor Ferri-Inductor Ferri-Inductor Ferri-Inductor Ferri-Inductor PML003AM PAL005A PE5139A S-80734AN PM4009A IMH3A DTA124EU 2SC4081 DTA124EU IMH3A DTA114ES 2SC1740S 2SD1757K 2SD1757K DTC144ES DTA114ES 2SA933S 2SB1236 DTC124ES DTA124ES 2SA1576 IMX1 2SD1859 2SD2396 IMD2A 2SD2396 IMD2A MTZ5R6J(C) DA204U DA204U DA204U DAN202U ERA15-02VH ERA15-02VH ERA15-02VH ERA15-02VH HZS7L(C2) HZS6L(C3) ERA15-02VH HZS6L(B1) HZS9L(B3) HZS9L(B1) LAU4R7K LAU2R2K LAU100K LAU100K LAU2R2K LAU2R2K LAU101K LAU101K

MISCELLANEOUS

RESISTORS
R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R 421 431 432 437 438 443 445 465 466 502 503 508 509 510 511 512 513 514 515 516 517 518 519 520 521 522 523 526 527 528 530 531 532 533 534 535 536 537 540 541 RS1/10S473J RS1/10S821J RS1/10S821J RS1/10S223J RS1/10S223J RS1/10S0R0J RS1/8S473J RD1/4PU221J RD1/4PU221J RD1/4PU222J RS1/10S222J RS1/10S681J RS1/10S473J RS1/10S681J RS1/10S473J RS1/10S681J RS1/8S473J RS1/10S681J RS1/8S473J RS1/10S681J RS1/8S472J RS1/10S103J RS1/10S393J RS1/10S681J RS1/10S473J RD1/4PU681J RS1/10S473J RS1/10S104J RS1/10S104J RD1/4PU102J RS1/10S681J RS1/10S473J RD1/4PU681J RS1/10S473J RS1/10S162J RS1/10S162J RS1/10S272J RS1/10S272J RS1/10S224J RS1/10S224J

38

DEH-3130R,3100R-B,3100R

=====Circuit Symbol and No.===Part Name --- ----------------------------------------------R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R 542 543 544 545 546 547 570 579 580 602 603 606 607 608 610 611 613 614 615 616 617 618 625 626 631 632 641 651 652 653 654 655 656 657 658 659 660 662 681 682 683 684 704 705 706 713 714 716 717 718 727 921 923 924 925 971 972 973 974 975 976 977 978 979 981

Part No. ------------------------RS1/10S224J RS1/10S222J RS1/10S222J RS1/10S223J RS1/10S223J RS1/10S472J RD1/4PU103J RS1/10S331J RS1/10S103J RD1/4PU473J RS1/10S102J RD1/4PU102J RD1/4PU102J RD1/4PU102J RS1/10S222J RS1/10S473J RS1/10S0R0J RD1/4PU222J RD1/4PU473J RS1/10S222J RS1/10S473J RN1/10SE2002D RS1/10S0R0J RD1/4PU102J RS1/10S102J RS1/10S822J RD1/4PU102J RS1/10S222J RD1/4PU472J RS1/10S222J RD1/4PU222J RD1/4PU222J RD1/4PU222J RS1/10S473J RD1/4PU472J RS1/8S472J RD1/4PU302J RS2PMF200J RS1/10S681J RD1/4PU102J RS1/10S102J RD1/4PU102J RS1/10S102J RD1/4PU102J RD1/4PU102J RS1/10S0R0J RD1/4PU102J RS1/10S0R0J RS1/10S225J RS1/10S0R0J RD1/4PU681J RS1/10S153J RS1/10S472J RD1/4PU102J RS1/10S473J RS1/10S103J RS1/10S473J RS1/10S103J RS1/10S473J RS1/10S473J RS1/10S473J RD1/4PU101J RS1/10S472J RS1/10S472J RS1/10S1R0J

=====Circuit Symbol and No.===Part Name --- ----------------------------------------------R R R R R R 982 987 991 992 993 994

Part No. ------------------------RD1/4PU511J RD1/4PU221J RD1/4PU221J RD1/4PU221J RS1/10S472J RS1/10S222J

CAPACITORS
C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C 431 432 451 452 453 454 455 456 457 458 461 462 463 465 466 501 502 503 504 505 506 507 508 509 519 524 525 531 536 537 540 551 552 553 554 556 570 571 572 573 601 602 603 604 605 607 609 619 621 622 631 652 653 701 702 4700F/16V CEJA4R7M35 CEAL4R7M35 CKSYB224K25 CKSYB224K25 CKSYB474K16 CKSYB474K16 CEJANP4R7M16 CEJANP4R7M16 CKSQYB153K50 CKSQYB153K50 CEAL470M10 CKSQYB104K25 CEJA100M16 CCSQSL182J50 CCSSL182J50 CKSQYB103K50 CKSQYB223K50 CKSQYB223K50 CEJA220M10 CKSQYB102K50 CEAL101M10 CKSQYB473K25 CCSQCH101J50 CKSQYB102K50 CKSQYB472K50 CEJA1R0M50 CEJA1R0M50 CKSQYB182K50 CKSQYB123K50 CKSQYB123K50 CKSQYB223K50 CKSYB224K25 CKSYB224K25 CKSYB224K25 CKSYB224K25 CCH1328 CEJA100M16 CEJA330M10 CKSYB105K16 CKSYB104K50 CCSQCH200J50 CCSQCH200J50 CKSYB105K16 CEJA4R7M35 CCSQCH101J50 CCSQCH101J50 CCSQCH101J50 CCSQCH101J50 CCSQCH101J50 CCSQCH101J50 CEJA2R2M50 CEJA4R7M35 CKSQYB473K25 CEAL220M6R3 CKSQYB104K25

39

DEH-3130R,3100R-B,3100R

=====Circuit Symbol and No.===Part Name --- ----------------------------------------------C C C C C C C C C C C C C C C C C 711 712 715 717 718 721 722 971 972 973 974 981 982 983 991 992 993

Part No. ------------------------CCSQCH270J50 CCSQCH270J50 CKSQYB104K50 CKSQYB471K50 CKSYB471K50 CEAL220M6R3 CKSQYB104K25 CCH1331 CKSQYB473K25 CEJA101M10 CKSQYB473K25 CCH1326 CKSQYB103K50 CEJA101M16 CKSQYB473K25 CKSQYB102K50 CEJA101M10

=====Circuit Symbol and No.===Part Name --- ----------------------------------------------R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R 9 10 11 12 13 16 17 18 19 20 51 52 53 54 55 56 57 58 59 60 61 62 101 102 103 104 106 108 110 111 112 113 114 115 116 117 118 122 202 203 204 205 206 208 209 210 213 251 902 904 907 908 909 914

Part No. ------------------------RS1/16S223J RS1/16S473J RS1/16S221J RS1/16S103J RS1/16S104J RS1/16S223J RS1/16S221J RS1/16S221J RS1/16S473J RS1/16S470J RS1/16S470J RS1/16S103J RS1/16S103J RS1/16S331J RS1/16S331J RS1/16S560J RS1/16S560J RS1/16S102J RS1/16S225J RS1/16S133J RS1/16S433J RS1/16S562J RS1/16S333J RS1/16S103J RS1/16S333J RS1/16S562J RS1/16S0R0J RS1/16S0R0J RS1/16S154J RS1/16S273J RS1/16S223J RS1/16S222J RS1/16S333J RS1/16S334J RS1/16S473J RS1/16S333J RS1/16S223J RS1/16S0R0J RS1/16S472J RS1/16S225J RS1/16S102J RS1/16S220J RS1/16S471J RS1/16S104J RS1/16S104J RS1/16S563J RS1/16S223J RS1/16S225J RS1/16S103J RS1/16S473J RS1/16S103J RS1/16S681J RS1/16S473J RS1/16S562J

470F/16V

330F/16V

B
IC IC IC Q Q Q Q Q Q Q D D D D D D D D D L L L L L L L L L L L T CF CF CF CF X

Unit Number : CWE1500 Unit Name : FM/AM Tuner Unit

1 2 3 1 2 3 51 201 202 204 1 2 4 6 101 201 202 903 904 1 2 3 4 201 202 203 901 902 904 905 51 51 52 53 202 901 IC IC IC Transistor Transistor FET Transistor FET Transistor Transistor Diode Diode Diode Diode Diode Diode Diode Diode Diode Coil Coil Inductor Coil Inductor Inductor Inductor Coil Inductor Inductor Inductor Coil Ceramic Filter Ceramic Filter Ceramic Filter Ceramic Filter Crystal Resonator 10.250MHz PML002A PM4008A BR9010FV 2SC4081 DTC124EU 3SK263 2SC4081 2SK932 DTC124EU 2SC4081 KV1410(23) 1SV248 KV1410(23) KV1410(23) 1SS355 DAN217U DAN217U KV1410(23) SVC253 CTC1155 CTC1155 LCTB100K2125 CTC1155 LCTB330K1608 CTF1287 LCTA121J3225 CTC1154 LCTA3R3J3225 LCTBR47K1608 LCTBR47K1608 CTE1132 CTF1442 CTF1442 CTF1442 CTF1348 CSS1432

MISCELLANEOUS

CAPACITORS
C C C C C C C C C C 1 2 4 6 8 10 11 12 14 15 CCSQCH5R0C50 CCSRCH5R0C50 CCSRCJ3R0C50 CKSQYB105K10 CKSRYB222K50 CCSRCH220J50 CCSRCH150J50 CCSRCH8R0D50 CCSRCJ3R0C50 CKSRYB103K50

RESISTORS
R R R R R 1 2 6 7 8 RS1/16S153J RS1/16S103J RS1/16S103J RS1/16S273J RS1/16S473J

40

DEH-3130R,3100R-B,3100R

=====Circuit Symbol and No.===Part Name --- ----------------------------------------------C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C 16 17 18 19 20 21 24 31 32 35 51 52 53 54 55 56 58 59 60 101 102 103 105 106 107 108 109 110 111 112 113 114 115 116 117 120 121 122 123 125 126 127 128 201 202 203 204 205 206 207 208 209 210 211 212 215 216 217 219 220 221 222 223 224 225

Part No. ------------------------CKSRYB222K50 CKSRYB222K50 CCSRCJ3R0C50 CKSRYB103K50 CKSRYB103K50 CKSRYB103K50 CKSQYB334K16 CKSRYB222K50 CCSRCH470J50 CKSRYB103K50 CKSRYB103K50 CKSRYB473K16 CCSRCK2R0C50 CKSRYB103K50 CKSRYB104K16 CKSRYB104K16 CKSQYB224K16 CKSRYB223K25 CKSRYB104K16 CEALNP100M10 CCSRCH151J50 CKSRYB473K16 CKSRYB682K25 CEAL2R2M50 CKSRYB103K50 CKSQYB474K16 CKSQYB474K16 CKSRYB104K16 CKSRYB104K16 CKSRYB104K16 CKSRYB123K25 CEAL220M6R3 CKSRYB473K16 CEAL2R2M50 CKSRYB102K50 CKSRYB153K25 CKSRYB332K50 CKSRYB682K25 CKSRYB681K50 CKSRYB103K50 CKSRYB103K50 CEAL2R2M50 CKSRYB103K50 CCSRCH471J50 CCSRCH100D50 CKSRYB104K16 CKSRYB332K50 CKSRYB103K50 CKSRYB104K16 CKSRYB473K16 CCSRCH560J50 CEAL470M6R3 CKSRYB103K50 CKSRYB103K50 CCSRCH101J50 CKSRYB223K25 CKSQYB334K16 CKSRYB103K50 CKSQYB105K10 CKSRYB104K16 CKSRYB473K16 CKSQYB334K16 CKSQYB474K16 CKSRYB104K16 CKSRYB272K50

=====Circuit Symbol and No.===Part Name --- ----------------------------------------------C C C C C C C C C C C C C C C C C C C C 226 902 904 905 906 907 909 910 912 913 914 915 916 917 918 919 920 921 922 923

Part No. ------------------------CKSRYB682K25 CCSRCH270J50 CKSRYB223K25 CKSRYB103K50 CCSRTH100D50 CCSRTH150J50 CCSRTH100D50 CKSRYB332K50 CKSQYB474K16 CKSRYB223K25 CKSRYB682K25 CKSQYB223K25 CKSQYB474K16 CKSYB475K10 CKSRYB223K25 CKSQYB225K10 CCSRCH270J50 CCSRCH270J50 CKSYB105K16 CKSRYB103K50

C
IC D D D D D D D D D D D X S S S S S S S S S S S S S S S S S S S S S S

Unit Number : CWM6796 Unit Name : Keyboard Unit : (DEH-3130R/X1N/EW)

MISCELLANEOUS
1801 1801 1802 1803 1804 1807 1808 1809 1810 1811 1812 1813 1801 1801 1802 1803 1804 1805 1806 1807 1808 1809 1810 1811 1812 1813 1814 1815 1816 1817 1818 1819 1820 1821 1822 LCD IC Diode Network Diode Network LED LED LED LED LED LED LED LED LED Radiator 5.00MHz PD6294A DA204U DA204U NSSW440-9159 NSSW440-9159 NSSW440-9159 NSSW440-9159 CL220D CL220D CL170DCD CL170DCD CL170DCD CSS1423 CSG1114 CSG1114 CSG1114 CSG1114 CSG1114 CSG1114 CSG1117 CSG1114 CSG1114 CSG1114 CSG1114 CSG1114 CSG1117 CSG1117 CSG1111 CSG1114 CSG1114 CSG1114 CSG1117 CSG1111 CSG1111 CSG1111 CAW1570

RESISTORS
R R R R R 1801 1802 1803 1806 1808 RS1/8S222J RS1/8S222J RS1/10S472J RS1/4S391J RS1/4S391J

41

DEH-3130R,3100R-B,3100R

=====Circuit Symbol and No.===Part Name --- ----------------------------------------------R R R R R R R R R R R R 1809 1810 1811 1812 1813 1814 1815 1816 1817 1818 1819 1821

Part No. ------------------------RS1/4S301J RS1/4S301J RS1/4S301J RS1/4S301J RS1/4S301J RS1/4S301J RS1/4S431J RS1/4S431J RS1/4S821J RS1/10S103J RS1/10S0R0J RS1/4S272J

=====Circuit Symbol and No.===Part Name --- -----------------------------------------------

Part No. -------------------------

RESISTORS
R R R R R R R R R R R R R R R R R 1801 1802 1803 1806 1808 1809 1810 1811 1812 1813 1814 1815 1816 1817 1818 1819 1821 RS1/8S222J RS1/8S222J RS1/10S472J RS1/4S271J RS1/4S271J RS1/4S301J RS1/4S301J RS1/4S301J RS1/4S301J RS1/4S301J RS1/4S301J RS1/4S431J RS1/4S431J RS1/4S821J RS1/10S103J RS1/10S0R0J RS1/4S272J

CAPACITORS
C C C C C C C C C 1801 1803 1804 1805 1806 1807 1808 1811 1812 CKSQYB104K50 CKSQYB104K50 CKSQYB104K50 CKSQYB104K50 CKSQYB104K50 CKSQYB104K50 CKSQYB104K50 CKSQYB104K50 CKSQYB104K50

CAPACITORS
C C C C C C C C C 1801 1803 1804 1805 1806 1807 1808 1811 1812 CKSQYB104K50 CKSQYB104K50 CKSQYB104K50 CKSQYB104K50 CKSQYB104K50 CKSQYB104K50 CKSQYB104K50 CKSQYB104K50 CKSQYB104K50

C
IC D D D D D D D D D D D X S S S S S S S S S S S S S S S S S S S S S S

Unit Number : CWM6797 Unit Name : Keyboard Unit : (DEH-3100R-B/X1N/EW)

IC Diode Network Diode Network LED LED LED LED LED LED LED LED LED Radiator 5.00MHz PD6294A DA204U DA204U NSSW440-9159 NSSW440-9159 NSSW440-9159 NSSW440-9159 CL220SRCTS CL220SRCTS CL170SRCD CL170SRCD CL170SRCD CSS1423 CSG1135 CSG1135 CSG1135 CSG1135 CSG1135 CSG1135 CSG1133 CSG1135 CSG1135 CSG1135 CSG1135 CSG1135 CSG1133 CSG1133 CSG1111 CSG1135 CSG1135 CSG1135 CSG1133 CSG1111 CSG1111 CSG1111 LCD CAW1572

MISCELLANEOUS
1801 1801 1802 1803 1804 1807 1808 1809 1810 1811 1812 1813 1801 1801 1802 1803 1804 1805 1806 1807 1808 1809 1810 1811 1812 1813 1814 1815 1816 1817 1818 1819 1820 1821 1822

C
IC D D D D D D D D D D D X S S S S S S S S S S S S S S S S S

Unit Number : CWM6795 Unit Name : Keyboard Unit : (DEH-3100R/X1N/EW)

IC Diode Network Diode Network LED LED LED LED LED LED LED LED LED Radiator 5.00MHz PD6294A DA204U DA204U NSSW440-9159 NSSW440-9159 NSSW440-9159 NSSW440-9159 CL220PGC CL220PGC CL170PGCD CL170PGCD CL170PGCD CSS1423 CSG1112 CSG1112 CSG1112 CSG1112 CSG1112 CSG1112 CSG1107 CSG1112 CSG1112 CSG1112 CSG1112 CSG1112 Switch Switch CSG1107 CSG1107 CSG1111 CSG1112 CSG1112

MISCELLANEOUS
1801 1801 1802 1803 1804 1807 1808 1809 1810 1811 1812 1813 1801 1801 1802 1803 1804 1805 1806 1807 1808 1809 1810 1811 1812 1813 1814 1815 1816 1817

Switch

42

DEH-3130R,3100R-B,3100R

=====Circuit Symbol and No.===Part Name --- ----------------------------------------------S S S S S 1818 1819 1820 1821 1822 Switch

Part No. ------------------------CSG1112 CSG1107 CSG1111 CSG1111 CSG1111 CAW1570

=====Circuit Symbol and No.===Part Name --- ----------------------------------------------R R R R R R R 602 605 606 801 803 902 906

Part No. ------------------------RS1/16S102J RS1/16S0R0J RS1/16S0R0J RS1/8S751J RS1/8S751J RS1/16S0R0J RS1/16S0R0J

LCD

RESISTORS
R R R R R R R R R R R R R R R R R 1801 1802 1803 1806 1808 1809 1810 1811 1812 1813 1814 1815 1816 1817 1818 1819 1821 RS1/8S222J RS1/8S222J RS1/10S472J RS1/4S391J RS1/4S391J RS1/4S301J RS1/4S301J RS1/4S301J RS1/4S301J RS1/4S301J RS1/4S301J RS1/4S431J RS1/4S431J RS1/4S821J RS1/10S103J RS1/10S0R0J RS1/4S272J

CAPACITORS
C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C 101 102 103 104 105 106 107 201 202 203 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 224 301 603 604 702 703 CCSRCH102J25 CKSRYB104K16 CEV101M6R3 CEV470M6R3 CKSQYB334K16 CKSQYB334K16 CKSQYB334K16 CKSRYB104K16 CKSRYB471K50 CKSRYB104K16 CEV101M6R3 CKSRYB104K16 CKSRYB104K16 CKSRYB104K16 CKSRYB104K16 CKSRYB332K50 CKSRYB104K16 CKSRYB104K16 CKSRYB392K50 CKSRYB104K16 CKSRYB104K16 CCSRCJ3R0C50 CCSRCH270J50 CKSRYB104K16 CCSRCH181J50 CCSRCH510J50 CKSRYB682K25 CEV220M6R3 CKSRYB103K25 CKSRYB224K10 CEV101M10 CCSQSL152J50 CCSQSL152J50 CCH1349 CKSQYB334K16

CAPACITORS
C C C C C C C C C 1801 1803 1804 1805 1806 1807 1808 1811 1812 CKSQYB104K50 CKSQYB104K50 CKSQYB104K50 CKSQYB104K50 CKSQYB104K50 CKSQYB104K50 CKSQYB104K50 CKSQYB104K50 CKSQYB104K50

D
IC IC IC Q D D X S S

Unit Number : CWX2411 Unit Name : Control Unit

MISCELLANEOUS
201 301 701 101 801 802 201 801 802 IC IC IC Transistor LED LED Ceramic Oscillator 16.934MHz Spring Switch(HOME) Spring Switch(CLAMP) UPD63711GC BA5985FM BA05SFP 2SB1132 CL200IRX CL200IRX CSS1456 CSN1051 CSN1052

10F/10V

E
Q Q

Unit Number : Unit Name : Photo Unit(S8)

1 2 Photo-transistor Photo-transistor CPT230SX-TU CPT230SX-TU

Miscellaneous Parts List

M M M 1 2 3 Pickup Unit(Service)(P8) Motor Unit(CARRIAGE) Motor Unit(LOADING) Motor Unit(SPINDLE) Fuse(10A) CXX1285 CXB2190 CXB2195 CXB2562 CEK1136

RESISTORS
R R R R R R R R R R R R R R R 101 102 103 201 202 203 204 205 206 207 302 303 501 502 601 RS1/8S120J RS1/8S100J RS1/16S222J RS1/16S104J RS1/16S103J RS1/16S393J RS1/16S103J RS1/16S103J RS1/16S182J RS1/16S123J RS1/16S153J RS1/16S103J RS1/16S102J RA4C681J RS1/16S102J

43

DEH-3130R,3100R-B,3100R

6. ADJUSTMENT
6.1 CD ADJUSTMENT
1) Precautions This unit uses a single power supply (+5V) for the regulator. The signal reference potential, therefore, is connected to REFO(approx. 2.5V) instead of GND. If REFO and GND are connected to each other by mistake during adjustments, not only will it be impossible to measure the potential correctly, but the servo will malfunction and a severe shock will be applied to the pick-up. To avoid this, take special note of the following. Do not connect the negative probe of the measuring equipment to REFO and GND together. It is especially important not to connect the channel 1 negative probe of the oscilloscope to REFO with the channel 2 negative probe connected to GND. Since the frame of the measuring instrument is usually at the same potential as the negative probe, change the frame of the measuring instrument to floating status. If by accident REFO comes in contact with GND, immediately switch the regulator or power OFF. Always make sure the regulator is OFF when connecting and disconnecting the various filters and wiring required for measurements. Before proceeding to further adjustments and measurements after switching regulator ON, let the player run for about one minute to allow the circuits to stabilize. Since the protective systems in the unit's software are rendered inoperative in test mode, be very careful to avoid mechanical and /or electrical shocks to the system when making adjustment. Disc detection during loading and eject operations is performed by means of a photo transistor in this unit.Consequently, if the inside of the unit is exposed to a strong light source when the outer casing is removed for repairs or adjustment, the following malfunctions may occur. *During PLAY, even if the eject button is pressed,the disc will not be ejected and the unit will remain in the PLAY mode. *The unit will not load a disc. When the unit malfunctions this way, either re-position the light source, move the unit or cover the photo transistor. 2) Test Mode This mode is used for adjusting the CD mechanism module of the device. Test mode starting procedure Reset while pressing the 4 and 6 keys together. Test mode cancellation Switch ACC, back-up OFF. After pressing the EJECT key, do not press any other key until the disk is completely ejected. If the ] or [ key is pressed while focus search is in progress, immediately turn the power off (otherwise the actuator may be damaged due to adhesion of the lenses). Jump operation of TRs other than 100TR continues after releasing the key. CRG move and 100TR jump operations are brought into the Tracking close status when the key is released. Powering Off/On resets the jump mode to Single TR (91), the RF AMP gain setting to 0 dB, and the automatic adjustment value to the initial value.

44

DEH-3130R,3100R-B,3100R

- Flow Chart
4
Test Mode In Reset

Select CD

SOURCE
New test mode

BAND
Power ON (Adjustment for T.Offset)
TRK MIN SEC

2 *1

Display

00 00 00

Power ON (Not adjustment for T.Offset)

TRK MIN SEC

RF AMP Gain Select

TRK MIN SEC

Display Power OFF

99 99 99

GG GG GG

BAND
Focus Close/ S Curve Check
TRK MIN SEC

3
Focus Mode Select

6 *2

] *8

[ *8
CRGSEC TRK MIN SEC

2 *3
Auto Adjustment Display Select

<Tracking Servo Close>

SEC TRK MIN SEC TRK

CRG+
MIN

TRK

MIN

Display

91 91 91

Display

0x 0x 0x

00 00 00
or
TRK MIN SEC

00 00 00
or
TRK MIN SEC

00 00 00
or
TRK MIN SEC

99 99 99
Power OFF

99 99 99

99 99 99

BAND
T.Close and F,T AGC and RF AGC and Fit Servo

T. Close and Fit Servo

RF AGC Coefficient Display/ Rough Servo and RF AGC

TRK

CRG+
MIN SEC

CRGTRK MIN SEC

T.Balance Adjustment

Display

8x 8x 8x
or
TRK MIN SEC

8x 8x 8x
or
TRK MIN SEC

9x 9x 9x
Power OFF

9x 9x 9x
Tracking Open

BAND

1 *7
F, T, RF AGC/ F.Bias Display Select

6 *5

*4 CRG-/TR Jump- *4
CRG+/TR Jump+

F, T AGC and RF AGC

CRG/TR Jump NO. Select

*6
TRK MIN SEC

Power OFF

Display

8x 8x 8x
or
TRK MIN SEC

BAND
Tracking Open

9x 9x 9x
SEC

*1 Display *2 Display

TYP

+6dB 06 06 06

+12dB 12 12 12
Display

TRK

MIN

8x 8x 8x
or
TRK MIN SEC

Focus Close 00 00 00 (99 99 99)

S Curve Check 01 01 01

9x 9x 9x
F.Cansel Display

*3

F.Offset Display

RF.Offset Display

F.Cancel Value = {Top Rank 8bit of Set Value (7F [H] to 80 [H] ) + 128} / 4 = 63 [D] to (32 [D] ) to 00 [D] *4 Single TR/32TR/100TR *5 Single TR Display 9x(8x):91(81) 32TRK 92(82) 100TRK 93(83) CRG Move 94(84)

*6 CRG Move, 100TR Jump Only *7 TRK, MIN, SEC F.AGC Gain T.AGC Gain RF AGC Gain

(F,T.AGC Gain = (Present Value/Initial Value) 20) *8 Voltage of CRG Motor = 2 [V]

45

DEH-3130R,3100R-B,3100R

6.2 CHECKING THE GRATING AFTER CHANGING THE PICKUP UNIT

Note : The grating angle of the PU unit cannot be adjusted after the PU unit is changed. The PU unit in the CD mechanism module is adjusted on the production line to match the CD mechanism module and is thus the best adjusted PU unit for the CD mechanism module. Changing the PU unit is thus best considered as a last resort. However, if the PU unit must be changed, the grating should be checked using the procedure below.

Purpose : To check that the grating is within an acceptable range when the PU unit is changed. Symptoms of Mal-adjustment : If the grating is off by a large amount symptoms such as being unable to close tracking, being unable to perform track search operations, or taking a long time for track searching. Method : Measuring Equipment Measuring Points Disc Mode

Oscilloscope, Two L.P.F. E, F, REFOUT ABEX TCD-784 TEST MODE

CONTROL UNIT

E F
E REFO

L.P.F. Xch 100k 390pF Ych

Oscilloscope

100k 390pF L.P.F.

REFO

REFO

Checking Procedure 1. In test mode, load the disc and switch the 5V regulator on. 2. Using the ] and [ buttons, move the PU unit to the innermost track. 3. Press key 3 to close focus, the display should read "91". Press key 2 to implement the tracking balance adjustment the display should now read "81". Press key 3 2 times. The display will change, returning to "81" on the fourth press. 4. As shown in the diagram above, monitor the LPF outputs using the oscilloscope and check that the phase difference is within 75 . Refer to the photographs supplied to determine the phase angle. 5. If the phase difference is determined to be greater than 75 try changing the PU unit to see if there is any improvement. If, after trying this a number of times, the grating angle does not become less than 75 then the mechanism should be judged to be at fault. Note Because of eccentricity in the disc and a slight misalignment of the clamping center the grating waveform may be seen to "wobble" ( the phase difference changes as the disc rotates). The angle specified above indicates the average angle. Hint Reloading the disc changes the clamp position and may decrease the "wobble".

46

DEH-3130R,3100R-B,3100R

Grating waveform

Ech Xch 20mV/div, AC Fch Ych 20mV/div, AC 30

45

60

75

90

47

DEH-3130R,3100R-B,3100R

7. GENERAL INFORMATION
7.1 DIAGNOSIS 7.1.1 TEST MODE
- Error Messages
If a CD is not operative or stopped during operation due to an error, the error mode is turned on and cause(s) of the error is indicated with a corresponding number. This arrangement is intended at reducing nonsense calls from the users and also for facilitating trouble analysis and repair work in servicing. (1) Basic Indication Method 1) When SERRORM is selected for the CSMOD (CD mode area for the system), error codes are written to DMIN (minutes display area) and DSEC (seconds display area). The same data is written to DMIN and DSEC. DTNO remains in blank as before. 2) Head unit display examples Depending on display capability of LCD used, display will vary as shown below. xx contains the error number. 8-digit display ERRORxx 6-digit display ERRxx OR Errxx 4-digit display Exx

(2) Error Code List Code Class Displayed error code Description of the code and potential cause(s) 10 Electricity Carriage Home NG CRG can't be moved to inner diameter. CRG can't be moved from inner diameter. Failure on home switch or CRG move mechanism. 11 12 Electricity Electricity Focus Servo NG Spindle Lock NG Subcode NG Focusing not available. Stains on rear side of disc or excessive vibrations on REWRITABLE. Spindle not locked. Sub-code is strange (not readable). Failure on spindle, stains or damages on disc, or excessive vibrations. A disc not containing CD-R data is found. Turned over disc are found, though rarely. Failure on home switch or CRG move mechanism. An appropriate RF AMP gain can't be determined. CD signal error. APC protection doesn't work. Focus can be easily lost. Damages or stains on disc, or excessive vibrations. Failed to reach target address. CRG tracking error or damages on disc. Power (VD) is ground faulted. Failure on SW transistor or power supply (failure on connector).

RF AMP NG 17 30 A0 Electricity Electricity System Setup NG Search Time Out Power Supply NG

Remarks: Mechanical errors are not displayed (because a CD is turned off in these errors). Unreadable TOC does not constitute an error. An intended operation continues in this case. A newly designed head unit must conform to the example given above. Upper digits of an error code are subdivided as shown below: 1x: Setup relevant errors, 3x: Search relevant errors, 3x: Search relevant errors, Ax: Other errors.

48

DEH-3130R,3100R-B,3100R

- New Test Mode

S-CD plays the same way as before. If an error such as off focus, spindle unlocking, unreadable sub-code, or sound skipping occurs after setup, its cause and time occurred (in absolute time) are displayed. During setup, operational status of the control software (internal RAM: CPOINT) is displayed. These displays and functions are prepared for enhancing aging in the servicing and efficiency of trouble analysis. (1) Shifting to the New Test Mode 1 Turn on the current test mode by starting the reset from the key. 2 Select S-CD for the source through the specified procedure including use of the [SOURCE] key, and inserting the disc. Then, press the [Jump Mode Selector] key while maintaining the regulator turned off. 3 After the above operations, the new test mode remains on irrespective of whether the S-CD is turned on or off. You can reset the new test mode by turning on the reset start. * With some products, the new test mode can be reset through the same operations as that employed for shifting to the STBY mode (while maintaining the Acc turned off). (2) Key Correspondence Key Test mode (Example) Power Off Power On BAND To power on To power off (offset adjustment performed) ] [ 1 2 3 RF AMP gain switching FWD-Kick REV-Kick T.Close (AGC performed) /parameter display switching Parameter display switching /T.BAL adjustment/T.Open F.Close/RF AGC/F.T.AGC

In-play FF/TR+ REV/TRScan Mode

New test mode Error Production Time/Err.No. switching

To power on (offset adjustment not performed) 6 F.Mode switching Auto/Manu T.No./Time switching /T.Close (no AGC)/Jump switching Note: Eject and CD on/off is performed in the same procedure as that for the normal mode. (3) Cause of Error and Error Code Code Class Contents 40 Electricity Off focus detected. 41 42 43 Electricity Electricity Electricity Spindle unlocked. Sub-code unreadable. Sound skipping detected.

Description and cause FOK goes low. Damages/stains on disc, vibrations or failure on servo. FOK = Low continued for 50 msec. Damages/stains on disc, vibrations or failure on servo. Sub-code was unreadable for 50 msec. Damages/stains on disc, vibrations or failure on servo. Last address memory function was activated. Damages/stains on disc, vibrations or failure on servo.

Note: Mechanical errors during aging are not displayed. The error codes should be indicated in the same way as in the normal mode.

49

DEH-3130R,3100R-B,3100R

(4) Display of Operational Status (CPOINT) during Setup Status No. Contents 00 CD+5V ON process in progress. 01 Servo LSI initialization (1/3) in progress. 02 Servo LSI CRAM initialization in progress. 03 Servo LSI initialization (2/3) in progress. 04 Offset adjustment (1/3) in progress. 05 Offset adjustment (2/3) in progress. 06 Offset adjustment (3/3) in progress. 07 FZD adjustment in progress. 08 Servo LSI initialization (3/3) in progress. 10 Carriage move to home position started. 11 Carriage move to home position started. 12 Carriage is moving toward inner diameter. 13 14 15 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 Carriage is moving toward outer diameter. Carriage outer kick in progress. Carriage outer diameter feed (1 second) in progress. Servo close started. Pre-processing for focus search started. Spindle rotation and focus search started. Waiting for focus close (XSI=Low). Standing by after focus close is over. Focus search preprocessing is in progress while setup protection is turned on. Focus search preprocessing is in progress while focus recovery is turned on. Wait time after focus close is set up. Standing by after focus close is over. Setup (1/2) before T balance adjustment is started. Setup (2/2) before T balance adjustment is started. T balance adjustment started. T balance adjustment (1/2). T balance adjustment (2/2). Waiting for spindle rotation to end. Spindle rough servo. Standing by after spindle rough servo is over. RF AGC started. RF AGC started. RF AGC ending process in progress. Tracking close in progress. Standing by after tracking is closed. Carriage closing in progress. Focus/tracking AGC started. Focus AGC started. Focus AGC in progress. Tracking AGC in progress. Standing by after focus/tracking AGC are over. Spindle processes applicable servo. Check for servo close is started. Check of LOCK pin started. RF AGC started. RF AGC in progress. Standing by after RF AGC is over.

Protective action None None None None None None None None None None None Specified 10 seconds has been passed or failure on home switch. Specified 10 seconds has been passed or failure on home switch. None None None None None Specified focus search time has been passed. Specified focus search time has been passed. None None Off focus. Off focus. Off focus. Off focus. Off focus. Off focus. Off focus. Off focus. Off focus. Off focus. Off focus. Off focus. Off focus. Off focus. Off focus. Off focus. Off focus. Off focus. Off focus. Off focus. Off focus. Off focus or spindle not locked. Off focus. Off focus. Off focus.

50

DEH-3130R,3100R-B,3100R

(5) Display Examples 1) During Setup (When status no. = 11) TRK No. MIN. SEC. 11 11' 11" 2) During Operation (TOC read, TRK search, Play, FF and REV) The same as in the normal mode. 3) When a Protection Error Occurred Switch to the following displays (A) and (B) using the [BAND] switch: (A) Error occurrence timing display in absolute time. An example: Error occurred in 12th tune at 34'56" in absolute time. TRK No. 12 MIN. 34' SEC. 56"

(B) Error No. display An example: Error #40 (Off focus is detected) ERROR-40

51

DEH-3130R,3100R-B,3100R

7.1.2 DISASSEMBLY

- Removing the Case Unit(not shown) 1. Remove the Case Unit. - Removing the Panel Assy(Fig.1) Disengage the stoppers at two locations.

Remove the Panel Assy.

- Removing the CD Mechanism Module

(not shown)
1. Remove the four screws. 2.Disconnect the connector, and then remove the CD Mechanism Module.

Panel Assy Fig.1

- Removing the Tuner Amp Unit(Fig.2) Remove the two screws.

Remove the three screws.

Remove the screw.

Straighten the tabs at four locations indicated. Remove the Tuner Amp Unit.

Tuner Amp Unit

Fig.2

52

DEH-3130R,3100R-B,3100R

- Removing the Upper Frame

1. Remove six Springs A, two Springs B and four Screws. 2. Remove two Tabs situated on rear side of the Upper Frame, remove two Arms on the front side, then remove two Tabs on the front side.
A A

A Upper Frame

Arm

Arm B A

- Removing the Carriage Mechanism

1. Disengage the Carriage Mechanism from the two dampers situated in the front side by driving it up, then disengage and remove the mechanism from the one damper by driving it up aslant into front side direction. Note : When assembling the Carriage Mechanism, coat the dampers with alcohol prior to the assembly.
Carriage Mechanism Section

- Removing the Clamp Arm Assy

1. Remove a Spring A, a B and a Spring C. 2. Drive the Clamp Arm Assy up into rear side direction, then disengage the arm from its current position Finally, drive the assembly approximately 45 degrees upward, then slide the assembly toward right side to remove it.

Clamp Arm Assy Section B

53

DEH-3130R,3100R-B,3100R

- Removing the Guide Arm Assy

1. Remove a connector, a spring A and B 2. Drive the Guide Arm Assy up aslant into rear side direction, then remove it from a Pin. Finally, drive the assembly approximately 45 degrees upward, then slide the assembly toward left side to remove it. Note : When assembling the guide arm assembly, route the cord inside the assembly. In this operation, care must be exercised so that cord may be caught by the gear.
Guide Arm Assy Section

B Pin

LO Arm Assy Section

- Removing the LO Arm Assy

1. Remove two Pins to dismount the LO Arm Assy.

- Removing the Control Unit and the Spindle Motor

1. Remove from the connector after mounting the short pin on the flexible PCB of the pickup unit. 2. Remove two Soldered joints, then remove two Screws A. 3. Remove two connectors and a Screw B. 4. Disengage the Control Unit from two Tabs, then dismount the unit by sliding it toward left. 5. Dismount the Spindle Motor.

Short Pin

Spindle Motor

Control Unit

54

DEH-3130R,3100R-B,3100R

- Removing the Loading Motor and Carriage Motor

1. Remove the Spring and two Screws A. 2. Dismount the Loading Motor. 3. Remove the Belt, a Screw B, two Screws C, a Guide and a Screw Unit. 4. Dismount the Carriage Motor. Note : When assembling the Belt, use care so that it may not be contaminated by grease.

C Guide

B Screw Unit Carriage Motor

Belt

A Loading Motor

- Removing the Pickup Unit

1. Remove two Screws and a Shaft. 2. Dismount the Pickup Unit.

Pickup Unit

Shaft

55

DEH-3130R,3100R-B,3100R

7.1 PARTS 7.2.1 IC

- Pin Functions (PE5139A)
Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23,24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42,43 44 45 46 4750 51 52 53 54 55 56 57 58 59 60 Pin Name DRSYS TELMUTE SYSPW DRELAY TESTIN drst ERROR sk RECIVE TUNPW reset XT2 XT1 VSS X2 X1 REGOFF REGC VDD GRNILM NC adpw NC ASENBO ROMDATA ROMCLK MUTE fm/AM LOCL LOCH TUNPCE2 VCK VST VDT tmute ROMCS SD st VSS VDD NC rdslk currq RDT NC swvdd dsens CONT CD5VON NC VDCONT CDMUTE CDEJET CDLOAD LOCK I/O O I O O I O O I O O I Function and Operation Door system select output Telephone mute input System power supply control output External relay output Test program mode input RDS reset output RDS disapprove of error correction output RDS SK signal input During RDS data reception output Tuner power control output Reset input Not used (open) Not used (GND) GND Crystal oscillator connection pin Crystal oscillator connection pin Connect to VSS Capacitor for regulator connect pin Power supply Green illumination select output Not used A/D converter power supply output Not used Slave power supply control output ROM correction data output ROM correction clock output System mute output RDS decoder power select output LOCL output LOCH output PLL IC chip enable output Clock output for electronic volume Strobe pulse output for electronic volume Data output for electronic volume Tuner mute output ROM correction chip select output SD input FM stereo input GND Power supply Not used RDS LK signal input Tuner voltage FIX output RDS demodulation data input Not used Keyboard unit power supply control output Grille detach sense input CD server driver power control output CD +5V power control output Not used CD VD power control output CD mute control output CD eject control output CD LOAD motor loading control output CD spindle lock input

O O O O O O O O O O O O O O O I I

I O I O I O O O O O O I

56

DEH-3130R,3100R-B,3100R

Pin No. 61 62 63 64 65 66 67 68 69 70 71,72 73 74 75 76 77 78 79 80 81 82 83 84 85,86 87 88 89 90 91 92 93 94 95 96 97 98 99 100

Pin Name FOK PCL MIRR clamp xsck XSI XSO XA0 xrst xstb NC TEST SL MODEL1 NL1 SDBW EJTSNS DSCSNS VDSENS TEMP (VDD) (VDD) (GND) NC GND ldet rck RDS57K SRVCNT asens bsens TUNPDI KEYDT DPDT TUNPCK TUNPDO TUNPCE PEE

I/O I O I I O I O O O O I I I I I I I I I

I I I I I I I O O O O O

Function and Operation CD focus OK input Clock adjustment output CD mirror detector input CD disc clamp sense input CD LSI clock output CD LSI data input CD LSI data output CD LSI command/data control output CD LSI reset output CD LSI strobe output Not used Test terminal Tuner signal level input Model select input RDS noise level input SD bandwidth input CD disc EJECT position detect CD disc detect input CD VD over voltage / short-circuit sense input CD temperature sense input (CD) A/D converter power supply terminal A/D converter reference voltage terminal A/D converter GND Not used GND RDS PLL lock sense input RDS demodulation clock input RDS 57kHz pulse count input Not used ACC power sense input Back up power sense input PLL IC data input Key data input Display data output PLL IC clock output PLL IC data output PLL IC chip enable Beep tone output

*PE5139A 30 1 31 100

IC's marked by* are MOS type. Be careful in handling them because they are very liable to be damaged by electrostatic induction.

50 51 80

81

57

DEH-3130R,3100R-B,3100R

- Pin Functions (PD6294A)

Pin No. 1 2 3 4 5,6 7 8 9 10 11,12 13-16 17-22 23 24-73 74-77 78 79,80 *PD6294A
20 1
21 80

Pin Name VSS X1 X0 NC MOD1,0 NC KYDT DPDT REMIN NC kd$-kd! KST6-KST1 VDD SEG49-0 COM3-0 VLCD V2,V1

I/O

I O I I I O O O I

Function and Operation GND Crystal oscillator connection pin Crystal oscillator connection pin Not used Connect to GND Not used Key data output Display data input Remote control pulse input Not used Key data input Key strobe output VDD LCD segment output LCD common output LCD voltage input Power supply terminal BR9010FV

NC

WC

VCC

CS
40 61

2 CS : Chip select input 7 SK : Serial data clock input DI : Serial data input DO : Serial data output 3 WC: Write control input 6

GND

DO

41

PAL005A

Protector

Mute

60

SK

DI

Mute

Mute

Mute

STBY

Amp2

Amp1

Amp3

Amp4

1 TAB

2 P-GND2

3 OUT2-

4 STBY

5 OUT2+

6 VCC

7 OUT1-

8 P-GND1

9 OUT1+

10 SVR

11 IN1

12 IN2

13 S-GND

14 IN4

15 IN3

16 Ac_gnd

17 OUT3+

18 P-GND3

19 OUT3-

20 VCC

21 OUT4+

22 MUTE

23 OUT4-

24 P-GND4

25 Switch_out

58

DEH-3130R,3100R-B,3100R

PML003AM
VCC 28 IN1_R 27 IN2_R 26 IN3_R IN4+_R IN4-_R 23 25 24 Isolator circuit

LoudAGND out_R 22 21

SVin_R 20

Frontout_R 19

Rearout_R FIE_R 18 17

STB 16

DATA 15

FIE Anti Alias filter Primary volume Anti radiation filter Loudness volume Bass Fader volume Secondary volume

Treble Middle

Auto-Zero

Zero cross detect circuit Digital block

Auto-Zero

Primary volume

Middle

Bass

Treble Loudness volume Anti radiation filter

Zero cross detect circuit

Anti Alias filter Isolator circuit 1 Vref 2 IN1_L 3 IN2_L 4 IN3_L 5 6

Fader volume FIE

Secondary volume

10

11

12

13 DGND

14 CLK

IN4+_L IN4-_L

AGND Loudout_L

SVin_L Frontout_L

Rear- FIE_L out_L

PM4009A

59

DEH-3130R,3100R-B,3100R

- Pin Functions (UPD63711GC)

Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 Pin Name D.GND RFOK rst A0 stb sck SO SI xtalen D.VDD DA.VDD R_OUT DA.GND REGC DA.GND L_OUT DA.VDD R+ RLL+ X.VDD XTAL xtal X.GND D.VDD EMPH FLAG DIN DOUT SCKIN SCKO LRCKIN LRCK HOLD TX D.GND C16M LIMIT D.VDD LOCK RFCK MIRR PLCK D.GND C1D1 C1D2 C2D1 C2D2 C2D3 D.VDD PACK TSO TSI tsck TSTB D.GND I/O O I I I I O I I Function and Operation Logic circuit GND RFOK signal output Reset signal input Command/parameter identification signal input Data strobe signal input Clock signal input for serial data input/output Serial data and status signal output Serial data input Crystal oscillation control pin Positive power supply terminal to logic circuit Positive power supply terminal to D/A converter Right channel audio output signal D/A converter GND The outside putting capacitor connection pin for SCF regulator D/A converter GND Left channel audio output signal Positive power supply terminal to D/A converter Right channel audio data output Right channel audio data output Left channel audio data output Left channel audio data output Positive power supply terminal to crystal oscillation circuit Crystal oscillator connect pin Crystal oscillator connect pin Crystal oscillation circuit GND Positive power supply terminal to logic circuit Output pin for the pre-emphasis data in the sub-Q code Flag output pin to indicate that audio data currently being output consists of noncorrectable data Serial data input to internal DAC Serial audio data output Serial clock input to internal DAC Audio data that is output from DOUT changes at rising edge of this clock LRCK signal input to internal DAC Signals to distinguish the right and left channels of the audio data output from DOUT Defect detection output Digital audio interface data output Logic circuit GND Oscillator clock buffering output Status of the pin is output at Bit 5 of the status output Positive power supply terminal to logic circuit EFM synchronous detection signal Frame synchronous signal of XTAL-system MIRR output Monitor pin of bit clock Logic circuit GND Output pin for indicating the C1 error correction results Output pin for indicating the C1 error correction results Output pin for indicating the C2 error correction results Output pin for indicating the C2 error correction results Output pin for indicating the C2 error correction results Positive power supply terminal to logic circuit CD-TEXT PACK synchronous signal CD-TEXT data serial output CD-TEXT control parameter serial input CD-TEXT serial clock input CD-TEXT parameter strobe signal input Logic circuit GND

O I O O O O O I O

O O I O I O I O O O O I O O O O O O O O O O O I I I

60

DEH-3130R,3100R-B,3100R

Pin No. 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 *UPD63711GC

25 20 26 21

Pin Name TEST0 TEST1 ATEST A.GND FD TD SD MD DAC0 DAC1 DAC2 DAC3 A.VDD EFM ASY C3T RFI AGCO AGCI RFO EQ2 EQ1 RFA.GND A C B D F E A.VDD REFOUT FEFEO TETEO TE2 TEC A.GND PD LD PN A.VDD

I/O I I O O O O O O O O O O I I O I O

I I I I I I I O I O I O O I I O I

Function and Operation Test pin Test pin Test pin Analog circuit GND Focus drive output Tracking drive output Sled drive output Spindle drive output DAC output for adjustment DAC output for adjustment DAC output for adjustment DAC output for adjustment Positive power supply terminal to analog circuit EFM signal output EFM comparator reference voltage input 3T detection capacitor additional pin RF signal input for EFM data regulation RF signal output of after gain adjustment RF-AGC amplifier input RF summing amplifier output RF amplifier equalizer parts additional pin RF amplifier equalizer parts additional pin RF summing amplifier inverted input Analog circuit GND Photo detector A input Photo detector C input Photo detector B input Photo detector D input Photo detector F input Photo detector E input Positive power supply terminal to analog circuit Reference electric potential output Focus error amplifier inverted input Focus error amplifier output Tracking error amplifier inverted input Tracking error amplifier output Tracking error output of after amplification Tracking comparator input Analog circuit GND PD detection signal input for LD output monitor LD control current output APC circuit control polarity set pin Positive power supply terminal to analog circuit

1 1 100 80 76 61 75 60

50 40 51 41

61

DEH-3130R,3100R-B,3100R

- Pin Functions (BA5985FM)

Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 BA5985FM Pin Name FWD OPIN1(+) OPIN1() OPOUT1 OPIN2(+) OPIN2() OPOUT2 VCC VOL() VOL(+) VO2() VO2(+) VO1() VO1(+) VO4(+) VO4() VO3(+) VO3() GND BIAS MUTE OPOUT3 OPIN3() OPIN3(+) OPOUT4 OPIN4() OPIN4(+) REV I/O I I I O I I O O O O O O O O O O O I O I I O I I I Function and Operation Loading driver FWD input CH1 pre-amplifier input CH1 pre-amplifier inverted input CH1 pre-amplifier output CH2 pre-amplifier input CH2 pre-amplifier inverted input CH2 pre-amplifier output Power supply Loading driver negative output Loading driver positive output Driver CH2 negative output Driver CH2 positive output Driver CH1 negative output Driver CH1 positive output Driver CH4 positive output Driver CH4 negative output Driver CH3 positive output Driver CH3 negative output GND Bias input Mute control CH3 pre-amplifier output CH3 pre-amplifier inverted input CH3 pre-amplifier input CH4 pre-amplifier output CH4 pre-amplifier inverted input CH4 pre-amplifier input Loading driver REV input

62

DEH-3130R,3100R-B,3100R

7.2.2 DISPLAY
- CAW1570(DEH-3130R/X1N/EW, DEH-3100R/X1N/EW), CAW1572(DEH-3100R-B/X1N/EW)

SEGMENT

COMMON

63

DEH-3130R,3100R-B,3100R

8. OPERATIONS AND SPECIFICATIONS

8.1 OPERATIONS

5//2/3 buttons Disc loading slot EJECT button

FUNCTION button +/ button AUDIO button BAND button DETACH button EQ button Buttons 1 6 DISPLAY button PTY button SOURCE button TA/NEWS button

64

Basic Operation
Basic Operation of Tuner
This products AF function can be switched ON and OFF. AF should be switched OFF for normal tuning operations.

To Listen to Music

The following explains the initial of operations required before you can listen to music.

Note:

Loading a disc in this product.

1. Select the desired source (e.g. Tuner). Manual and Seek Tuning

You can select the tuning method by changing the length of time you press the 2/3 button.
Manual Tuning (step by step) Seek Tuning 0.5 seconds or less 0.5 seconds or more

Each press changes the Source ...

Each press of the SOURCE button selects the desired source in the following order: Built-in CD player = Tuner Note:

Note:

The sound source will not change if no disc is set in this product. When this products blue/white lead is connected to the cars Auto-antenna relay control terminal, the cars Auto-antenna extends when this products source is switched ON. To retract the antenna, switch the source OFF.

If you continue pressing the button for longer than 0.5 seconds, you can skip broadcast stations. Seek Tuning starts as soon as you release the button. Stereo indicator lights when a stereo station is selected.

Frequency Indicator Band Indicator Preset Number Indicator

2. Raise or lower the volume.

3. Turn the source OFF.

Hold for 1 second

Preset Tuning You can memorize broadcast stations in buttons 1 through 6 for easy, one-touch station recall.
Preset station recall Broadcast station preset memory 2 seconds or less 2 seconds or more

Band
FM 1 = FM 2 = FM 3 = MW/LW

Note:
Up to 18 FM stations (6 in FM1, FM2 and FM3) and 6 MW/LW stations can be stored in memory. You can also use the 5 or buttons to recall broadcast stations memorized in buttons 1 through 6.

DEH-3130R,3100R-B,3100R

65

Basic Operation Audio Adjustment

Selecting the Equalizer Curve
You can switch between Equalizer curves.

DEH-3130R,3100R-B,3100R

66

Basic Operation of Built-in CD Player

Eject
Note:

Move the EQ button up or down to select the desired Equalizer curve.

The CD function can be turned ON/OFF with the disc remaining in this product. A disc left partially inserted after ejection may incur damage or fall out. Equalizer curve

POWERFUL + NATURAL + VOCAL + CUSTOM + EQ FLAT + SUPER BASS = = = = = Note:

You can create different CUSTOM curves for different sources.

Disc Loading Slot

Note: With this Menu, you can adjust the sound quality. Note:

The Built-in CD player plays one standard 12 cm or 8 cm (single) CD at a time. Do not use an adapter when playing 8 cm CD.

Entering the Audio Menu

Track Number Indicator Play Time Indicator

After entering the Audio Menu, if you do not perform an operation within about 30 seconds, the Audio Menu is automatically canceled.

1. Select the desired mode in the Audio Menu.

Each press changes the Mode ...

2. Operate a mode. 3. Cancel the Audio Menu.

Track Search and Fast Forward/Reverse

You can select between Track Search or Fast Forward/Reverse by pressing the 2/3 button for a different length of time.
0.5 seconds or less Continue pressing

Track Search

Fast Forward/Reverse

Note:

If a disc cannot be inserted fully or playback fails, make sure the recorded side is down. Press the EJECT button and check the disc for damage before reinserting it. If a CD is inserted with the recorded side up, it will be ejected automatically after a few moments. If the Built-in CD player cannot operate properly, an error message (such as ERROR-14) appears on the display.

Audio Adjustment
Loudness Adjustment (LOUD)
The Loudness function compensates for deficiencies in the low and high sound ranges at low volume. You can select a desired Loudness level.

Audio Menu Functions

The Audio Menu features the following functions.

Balance Adjustment (FADER)

1. Press the AUDIO button and select the Loudness mode (LOUD) in the Audio Menu. 2. Switch the Loudness function ON/OFF with the 5/ buttons.

This function allows you to select a Fader/Balance setting that provides ideal listening conditions in all occupied seats.

1. Press the AUDIO button and select Fader/Balance mode (FADER) in the Audio Menu.

2. Adjust front/rear speaker balance with the 5/ buttons. 3. Select the desired level with the 2/3 buttons.
LOW + MID + HI = =

FADER :F 15 FADER :R 15 is displayed as it moves from front to rear.

3. Adjust left/right speaker balance with the 2/3 buttons.

BAL :L 9 BAL :R 9 is displayed as it moves from left to right.

Front Image Enhancer Function (FIE)

The F.I.E. (Front Image Enhancer) function is a simple method of enhancing front imaging by cutting mid- and high-range frequency output from the rear speakers, limiting their output to low-range frequencies. You can select the frequency you want to cut. Precaution:
When the F.I.E. function is deactivated, the rear speakers output sound of all frequencies, not just bass sounds. Reduce the volume before disengaging F.I.E. to prevent a sudden increase in volume.

Note:

FADER : 0 is the proper setting when 2 speakers are in use.

Equalizer Curve Adjustment (EQ-LOW/MID/HIGH)

You can adjust the currently selected equalizer curve settings as desired. Adjusted equalizer curve settings are memorized in CUSTOM.

1. Press the AUDIO button and select the Equalizer mode (EQ-LOW/MID/HIGH) in the Audio Menu.

1. Press the AUDIO button and select the F.I.E. mode (FIE) in the Audio Menu. 2. Switch the F.I.E. function ON/OFF with the 5/ buttons.
FIE

2. Select the band you want to adjust with the 2/3 buttons.

EQ-LOW + EQ-MID + EQ-HIGH = =

3. Boost or attenuate the selected band with the 5/ buttons.

The display shows +6 6.

3. Select the desired frequency with the 2/3 buttons.

100 + 160 + 250 (Hz) = = Note:
After switching the F.I.E. function ON, select the Fader/Balance mode in the Audio Menu, and adjust front and rear speaker volume levels until they are balanced. Switch the F.I.E. function OFF when using a 2-speaker system.

Note:

If you make adjustments when a curve other than CUSTOM is selected, the newly adjusted curve will replace the previous adjusted curve. Then a new curve with CUSTOM appears on the display while selecting the equalizer curve.

DEH-3130R,3100R-B,3100R

67

DEH-3130R,3100R-B,3100R

68
Antenna jack This Product Rear output Refer to Connecting to a Sold Separately Power Amp. Fuse Connect leads of the same color to each other. Blue/white To system control terminal of the power amp. (Max. 300 mA 12 V DC.) Refer to Connecting to a Sold Separately Power Amp. Fuse resistor The pin position of the ISO connector will differ depends on the type of vehicle. Connect 6* and 7* when Pin 5 is an antenna control type. In another type of vehicle, never connect 6* and 7*. Blue/white (6*) Speaker leads White : Front left + White/black : Front left Gray : Front right + Gray/black : Front right Green : Rear left + Green/black : Rear left Violet : Rear right + Violet/black : Rear right Blue/white (7*) To Auto-antenna relay control terminal. (Max. 300 mA 12 V DC.) Fuse resistor Yellow/black If you use a cellular telephone, connect it via the Audio Mute lead on the cellular telephone. If not, keep the Audio Mute lead free of any connections.

Note: Depending on the kind of vehicle, the function of 3* and 5* may be different. If this is the case, be sure to connect 2* to 5* and 4* to 3*.

1*

3*

2*

5*

4*

Cap (1*) When not using this terminal, do not remove the cap.

Yellow (3*) Back-up (or accessory)

Yellow (2*) To terminal always supplied with power regardless of ignition switch position.

Red (5*) Accessory (or back-up)

Red (4*) To electric terminal controlled by ignition switch (12 V DC) ON/OFF.

Black (ground) To vehicle (metal) body.

ISO connector Note: In some vehicles, the ISO connector may be divided into two. If this is the case, be sure to connect to both connectors.

DEH-3130R,3100R-B,3100R

8.2 SPECIFICATIONS

General
Power source .......... 14.4 V DC (10.8 15.1 V allowable) Grounding system ........................................ Negative type Max. current consumption ...................................... 10.0 A Dimensions (mounting size) ...... 178 (W) 50 (H) 159 (D) mm (front face) .............. 188 (W) 58 (H) 19 (D) mm Weight ...................................................................... 1.5 kg

CD player
System .................................... Compact disc audio system Usable discs .................................................. Compact disc Signal format .................... Sampling frequency: 44.1 kHz Number of quantization bits: 16; linear Frequency characteristics .............. 5 20,000 Hz (1 dB) Signal-to-noise ratio ...... 94 dB (1 kHz) (IEC-A network) Dynamic range ............................................ 92 dB (1 kHz) Number of channels ............................................ 2 (stereo)

Amplifier
Maximum power output ...................................... 45 W 4 Continuous power output .................................... 27 W 4 (DIN45324, +B = 14.4 V) Load impedance .......................... 4 (4 8 allowable) Preout maximum output level/output impedance ............................ 2.2 V/1 k Equalizer (3-Band Parametric Equalizer) (Low) .......................... Frequency: 40/80/100/160 Hz Q Factor: 0.35/0.59/0.95/1.15 (+6 dB when boosted) Level: 12 dB (Mid) .......................... Frequency: 200/500/1k/2k Hz Q Factor: 0.35/0.59/0.95/1.15 (+6 dB when boosted) Level: 12 dB (High) ................ Frequency: 3.15k/8k/10k/12.5k Hz Q Factor: 0.35/0.59/0.95/1.15 (+6 dB when boosted) Level: 12 dB Loudness contour (Low) .................. +3.5 dB (100 Hz), +3 dB (10 kHz) (Mid) ................ +10 dB (100 Hz), +6.5 dB (10 kHz) (High) ................ +11 dB (100 Hz), +11 dB (10 kHz) (volume: 30 dB)

FM tuner
Frequency range ...................................... 87.5 108 MHz Usable sensitivity...................................................... 11 dBf (1.0 V/75 , mono, S/N: 30 dB) 50 dB quieting sensitivity .... 16 dBf (1.7 V/75 , mono) Signal-to-noise ratio ...................... 70 dB (IEC-A network) Distortion .......................... 0.3% (at 65 dBf, 1 kHz, stereo) Frequency response ...................... 30 15,000 Hz (3 dB) Stereo separation .......................... 40 dB (at 65 dBf, 1 kHz)

MW tuner
Frequency range ...................................... 531 1,602 kHz Usable sensitivity .............................. 18 V (S/N: 20 dB) Selectivity .................................................. 50 dB (9 kHz)

LW tuner
Frequency range ........................................ 153 281 kHz Usable sensitivity .............................. 30 V (S/N: 20 dB) Selectivity .................................................. 50 dB (9 kHz)

Note:
Specifications and the design are subject to possible modification without notice due to improvements.

69