ENGINEERING GRAPHICS AND DESIGN 2/2

GRADE 10

TASK 7.2

NOVEMBER EXAMINATION 2021

MEMORANDUM

Page 1 of 6 © Impaq
 November Examination Memorandum 2021
G10 ~ Engineering Graphics and Design P2/2

ENGINEERING GRAPHICS AND DESIGN

NOVEMBER EXAMINATION 2021
PAPER 2/2
GRADE 10
MEMORANDUM
TOTAL: 150

NAME AND SURNAME

STUDENT
NUMBER
MARKS
MARKS
ACHIEVED

Question 1 31

Question 2 34

Question 3 37

Question 4 48

TOTAL 150

Page 2 of 6 © Impaq
QUESTION 1: MEMO QUESTION 1: ANALYTICAL (MECHANICAL)

GIVEN INFORMATION:
The drawing shows several views of a SUPPORT, a title block and a table of questions.

INDTRUCTIONS:
Complete the table below by neatly answering the questions, which refer to the accompanying drawing and title block. [31]

QUESTION ANSWERS Mark Mark achieved Mod

1
Name the system of projection and draw the
1. THIRD ANGLE ORTHOGRAPHIC PROJECTION 5
projection symbol in the provided space at (d).
(a) Which view can be seen in the direction
1
2. FRONT VIEW 1
(b) of arrow (a) on VIEW D?
1
Which view can be seen in the direction
VIEW D VIEW E 3. RIGHT VIEW 1
of arrow (B) on VIEW D?
1
Provide an appropriate label for each of the
4. VIEW A FULL SECTIONAL FRONT VIEW 1
130 (f) given views of the SUPPORT.
12 106 1
5. VIEW B TOP VIEW 1
Ø22 Ø42
12

1
6. VIEW C FULL SECTIONAL RIGHT VIEW 1
1
(l)
34

10
7. VIEW D ISOMETRIC VIEW 1
A A 1
FULL SECTIONAL
12

(j) 8. VIEW E 1
ISOMETRIC VIEW
Ø16 (n)
VIEW B 9.
Print the title "SUPPORT" in
(o) the provided space at (c). 1
(h) B R3
R44 1
If a scale of 1:5 were used, what would
10. 130 1
dimension (f) read?
27
1
R14 (k) If a scale of 5:1 were used, what would
47

(g) R20 11. 130 1

dimension (f) read?
1 1
(83)

Who made the drawing and when was

12. J Smit - 20/04/2004 2
it done?
(p) (i)
16

56

1 1
Who checked the drawing and when
13. W Nkozi - 21/04/2004 2
was it done?
10 10

1 1
Who approved the drawing and when
14. K Pienaar - 22/04/2004 2
B was it done?
40 50 30 1 1 1 1 1
15. Calculate the following dimensions. (l) 58 (m) 10 (n) Ø42 (o) Ø22 (p) 6 5
130
VIEW A VIEW C 1
16. What feature does (g) represent? RIB/WEB 1
1
17. What feature does (h) represent? FILLET 1
TEXAN 1 1
1
1
INDUSTRIES TITLE: SUPPORT 1 SYMBOL:
18. What feature does (i) represent? CENTRE LINE
1
1
Established 2000 c d
1
DRAWN: J Smit DATE: 20/04/2004 MATERIAL: CAST IRON SCALE: SCALE 1:2
19. What feature does (j) represent? HIDDEN DETAIL 1
CHECKED: W Nkozi DATE: 21/04/2004 ORDER NUMBER: HKGK 69 FILE NAME: SUPPORT 04/128/3 1
20. What feature does (k) represent? HATCHING 1
APPROVED: K Pienaar DATE: 22/04/2004 NUMBER REQUIRED: 234 DRAWING Nr. 04/128/3

TOTAL 31
CAD: NOTES: All fillets = 3 mm This drawing suppersedes drawing number 04/128/2
QUESTION 2: MEMO QUESTION 2: CONSTRUCTIONS

GIVEN INFORMATION:

Reference points and lines.

INSTRUCTIONS:

Answer the question by doing the activities step-by-step:

 Construct a pentagon with AB as the baseline.

 Construct a circumscribed circle for the triangle
CDE.
7
 Construct a tangent arc OF R100 that excludes
circle F and include circle G.
 Use the "four-centre method" and draw an ellipse
I with H as centre. The x- axis is 40mm and the y-axis
20mm.
7
5  Use line division and divide line IE into three equal
parts.
4 5  Construct a perpendicular line from point J and
7 extend to line KL.
5
 Construct a hexagon with baseline KL.

4 4 3 E PLEASE NOTE:
4 K L
4 4
2  ALL writing and line work must be in pencil
H  Show ALL constructions.
4 4 4 4
[34]
4 G

4
2 2

1
1 F

1 1
1
1
½ Mark 1 Mark
3
C D ASSESMENT RUBRIC
Mark Mark achieved Mod
1 3 1 Pentagon 7
2 Circumscribed circle 3
3 Arc 3
A B
4 Ellips 12
J
5 Line division 3
6 Perpendicular line 3
7 Hexagon 3
TOTAL 34
VRAAG 3: MEMO QUESTION 3: ISOMETRIC DRAWING

GIVEN INFORMATION:
The front view, top view and left view of a MODEL in third angle
orthographic projection.

INSTRUCTIONS:
2  Use the given information and make a neat isometric drawing of
the MODEL to a scale 1:1.
 All constructions and auxiliary views must be shown.
2  No hidden detail is required.
 Corner A should be the lowest point of the isometric drawing.
2 [37]
2

2
94
50 44
2 2
2
2 2
2
25
2

68
2

94
2
2

38

26
1
3
2
3 2 A
3 38
18 26 13 26 18
3 3
2
3 3
3
3

52
2
2 3 2

26
18
2
2
2 2
2

26
2 A A

1 1

½ Mark 1 Mark

A 1 1 ASSESMENT RUBRIC
Mark Mark achieved Mod
1 Placement & aux view 5
2 Drawing 27
3 Hexagon 5
TOTAL 37
QUESTION 4: MEMO
QUESTION 4: ORTHOGRAPHIC PROJECTION

GIVEN INFORMATION:

The figure shows the front view and the top view of
a BASE PLATE, in third angle orthographic
projection.

INSTRUCTIONS:

Draw the following views:

3.1 A full sectional front view on A-A.
3.2 A top view
3.3 A right view.
3.4 Draw the cutting plane on the top view.
2 [47]
2 2

2 2

2 2

4 4
5
4 4 80
2 2 2
4 A 5
A 4 15
2

2 2 Ø30

25
2

50
15
1 3
A Ø40 A

40
1 1 5 1 1 3 5
3 3
3

35
1 1
1 1 1
3 3
1 1 3

20
1 1 1 1 3
3

1 3

½ Mark 1 Mark
ASSESMENT RUBRIC
Mark Mark achieved Mod
1 Full sectional front view 16
2 Top view 14
3 Right view 11
4 Cutting plane 3
5 Center lines 4
TOTAL 48