Asscon Vapor Phase Soldering

BASICS OF VAPOR PHASE SOLDERING
Vapor Phase Soldering is also known as Condensation Soldering.
In the first process step the cold PCB is delivered to a chamber in which there is vapor
evaporated from a special liquid (medium) for this process – perfluoropolyether (PFPE).
process chamber
assembly
vapor
cooling
medium
heating elements
The liquid is chemically inert and with density almost twice higher than the water. Due to the
temperature difference between the PCB and the vapor, condensation on both sides of the
PCB starts immediately. The condensed vapor forms a thin film completely over the PCB.
condensation starts and

the vapor covers the
PCB from all sides as a
blanket
The high surface tension of the liquid used allows to cover well every critical gap on the PCB
such as the space under BGAs, closely placed or odd shaped components, etc.
Due to the high density of the vapor, the liquid film on the PCB pushes away the Oxygen.
Therefore the soldering process takes place in Oxygen free environment.
As the film conducts heat quite well, the thermal energy is transmitted to the PCB
homogeneously.
liquid film of
medium around the
assembly
The liquid is heated by electric heaters. Once the boiling point has been reached, the liquid
does not increase further in temperature. Any further energy supplied will be used to produce
more vapor (enthalpy of evaporation).
The amount of liquid condensing on the PCB depends on the amount of vapor in the chamber.
If you supply more heat from the heaters, the amount of vapor increases. By controlling the
heat transferred from the heaters to the liquid in the chamber, the amount of condensed liquid
on the PCB can be changed. This allows to change the rate of heating the PCB after entering
in the chamber.
The condensation of vapor stops when the PCB reaches the temperature of the vapor.
Therefore the boiling point of the liquid defines the maximum temperature to which the PCB is
exposed. For lead free soldering we recommend to use a liquid with 230ºC boiling point and for
Sn/Pb soldering - 200ºC. Other liquids are available from Asscon with boiling point from 160ºC to
260ºC. The special liquid for vapor phase soldering is available from several suppliers, not only
from Asscon.
assembly reached the

vapor temperature and
the vapor goes over the
assembly
When the solder paste is completely reflowed, the PCB is removed from the chamber. After the
PCB leaves the vapor zone, the remaining condensed fluid on the PCB evaporates, due to the
residual heat of the board.
end of the soldering

process - the
remaining medium
on the PCB
evaporates
In the last process step the soldered and dry PCB is cooled in a cooling zone.
Many test proved that on one and the same PCB the amount of voids after vapor phase
soldering is smaller compared to convection reflow soldering. To reduce further the amount of
voids Asscon developed a vacuum section which can be added to the high end vapor phase
ovens. The picture below on the right shows the reduction of voids using such section on the
same component under the same conditions, compared to the standard vapor phase
soldering (the picture on the left).
ABOUT ASSCON
The company was established in 1995 by several people who were involved in the design and
manufacture of vapor phase ovens of the earlier generation (1980’s). Taking into consideration
the demands of the Lead Free process, the latest developments of the liquids suitable for vapor
phase soldering and the limitations of the modern forced convection ovens, Asscon designed
first class reliable equipment performing with excellent repeatability and working with very low
running costs.
The company is located near Munich where all ovens are manufactured, tested and shipped
to the final destination.
The key advantages of Asscon vapor phase ovens are:
- soldering in O2 free environment (eliminates the need to use N2)

- guaranteed control of the max. temperature in the oven due to the physical properties
of the liquid used – typically 230ºC for Lead Free and 200ºC for Sn/Pb boards
- better heat transfer to the PCB due to the use of liquid for that and not air and N2. This
reflects in considerable reduction of electrical power consumption. The maximum power
consumption of the smallest oven (Quicky 300) is 2 kW, while the average consumption
during soldering is 1 kW. The maximum power consumption of the large inline oven (VP
2000) is 12 kW, while the average consumption during soldering is 6 kW.
- flexible and easy control of the PCB temperature until reaching the reflow values
- reduction of the voids in the solder joints. For further decreasing the amount of voids, a
vacuum section can be added to the vapor phase systems
- most complex and demanding PCB’s can be soldered with ovens that cost less
compared to the forced convection ovens
- the number of soldering defects is usually smaller
Due to the above reasons many leading manufacturers as Siemens, Bosch, Alcatel, Daimler
Chrysler, Motorola, Nokia, EADS, Semicron, Alenia, EPCOS, Matra, Marconi Aerospace and
others are already using the Asscon ovens. In many other contract manufacturers such as
Flextronics, Hella and others the Asscon vapor phase ovens are used for prototypes or for short
series of complex or difficult to solder PCBs.

Asscon Vapor Phase Soldering

Uploaded by

Copyright:

Available Formats

Asscon Vapor Phase Soldering

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Asscon Vapor Phase Soldering

Uploaded by

Copyright:

Available Formats

BASICS OF VAPOR PHASE SOLDERING

Vapor Phase Soldering is also known as Condensation Soldering.

condensation starts and

assembly reached the

end of the soldering

The key advantages of Asscon vapor phase ovens are:

- soldering in O2 free environment (eliminates the need to use N2)

You might also like