Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd Logo
Upload

Welcome to Scribd!

  • 17 views

    Yamaha YZF-R1-R1M Shock Absorber Mount YA 968

    Uploaded by

    Henrik Falk
    The document provides the kit contents and mounting instructions for installing an Öhlins YA 968 shock absorber on a Yamaha R1/R1M motorcycle. The kit includes the shock absorber, various stickers, an owner's manual, and is meant to replace the stock rear shock. The instructions provide notes on vehicle service information, cleaning the motorcycle before installing, and removing and installing the shock and linkages. Setup data is also included, such as recommended spring rate and preload, rebound and compression settings.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Yamaha YZF-R1-R1M Shock Absorber Mount YA 968

    Uploaded by

    Henrik Falk
    17 views4 pages
    The document provides the kit contents and mounting instructions for installing an Öhlins YA 968 shock absorber on a Yamaha R1/R1M motorcycle. The kit includes the shock absorber, various stickers, an owner's manual, and is meant to replace the stock rear shock. The instructions provide notes on vehicle service information, cleaning the motorcycle before installing, and removing and installing the shock and linkages. Setup data is also included, such as recommended spring rate and preload, rebound and compression settings.

    Original Title

    Yamaha_YZF-R1-R1M_Shock_Absorber_Mount_YA_968

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    The document provides the kit contents and mounting instructions for installing an Öhlins YA 968 shock absorber on a Yamaha R1/R1M motorcycle. The kit includes the shock absorber, various stickers, an owner's manual, and is meant to replace the stock rear shock. The instructions provide notes on vehicle service information, cleaning the motorcycle before installing, and removing and installing the shock and linkages. Setup data is also included, such as recommended spring rate and preload, rebound and compression settings.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    17 views4 pages

    Yamaha YZF-R1-R1M Shock Absorber Mount YA 968

    Uploaded by

    Henrik Falk
    The document provides the kit contents and mounting instructions for installing an Öhlins YA 968 shock absorber on a Yamaha R1/R1M motorcycle. The kit includes the shock absorber, various stickers, an owner's manual, and is meant to replace the stock rear shock. The instructions provide notes on vehicle service information, cleaning the motorcycle before installing, and removing and installing the shock and linkages. Setup data is also included, such as recommended spring rate and preload, rebound and compression settings.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 4

    Kit Contents

    Description Part No Pcs


    Shock absorber YA 968 1
    Sticker memo notes 01180-01 1
    Sticker set Öhlins 1
    Owner´s manual 07242-07 1

    1 Note! 1 Note!
    Please note that there can be small differences Before you install this product, check the kit
    between your product and the images in contents. If anything is missing, please contact
    these instructions. an Öhlins dealer.

    1 Note! ⚠ Warning!
    Please note that during storage and transport, Before you install this product, read the Öhlins
    especially at high ambient temperature, some Owner’s manual. This product is an important
    of the oil and grease used for assembly may part of the vehicle and the vehicle stability.
    leak and stain the packaging. This will not cause
    damage to the product, wipe off the excessive
    oil or grease with a cloth.

    Shock absorber for Yamaha R1/(R1M)

    YA 968
    Mounting Instructions
    MOUNTING INSTRUCTIONS
    ⚠ Warning! 5
    We strongly recommend to let an Öhlins dealer Remove the upper shock mounting bolt.
    install this product.
    6
    ⚠ Warning! Remove the shock absorber to the left.
    If you work with a lifted vehicle, make sure that it
    is safely supported to prevent it from tipping over. 1 Note!
    Adjust the swing arm height with a stand or
    1 Note! similar to make the removal easier.
    When you work with this product, see the
    7
    vehicle service manual for vehicle specific
    procedures and important data. Put the Öhlins shock and linkage in place.

    8
    1 Note!
    Before you install this product clean the vehicle. Install the shock absorber mounting bolt and
    the linkage. Load the suspension slightly
    1 before tightening.
    Put the bike on a stand so that the rear wheel 9
    is off the ground.
    Make sure that all bolts are tightened and that
    2 there are no clearance problems when the rear
    Remove the rear shock linkage bolt. wheel is moving.

    3 1 Note!
    Remove the lower shock mounting bolt. The Öhlins shock absorber will also fit the R1M
    model. Note that when you disconnect the STD
    4 shock absorber an error message will be shown
    Remove the front shock linkage frame bolt and on the display and you will not be able to enter
    bearing sleeve at the frame so the linkage is the main menu.
    removable.

    2 10
    Set system to non-electronic suspension.
    4 Turn ignition off.
    Hold gray arrow up button + mode button.
    Turn ignition on and wait for display to show menu set
    up mode.
    Release gray arrow up button + mode button.
    Select “meter” with gray arrow up/down button.
    Press gray arrow up button + mode button to go to
    next menu.
    Select 2 for Öhlins electronic suspension, and 1 for
    non-electronic suspension.
    Turn ignition off.

    2
    MOUNTING INSTRUCTIONS

    3
    ADJUSTMENTS
    Compression
    damping
    ⚠ Warning!
    adjuster
    Before you ride/drive, always make sure that the
    setup is according to the recommended setup
    data. Read about adjustments and setting up
    in the Öhlins Owner’s Manual before you make
    Spring
    any adjustments. Contact an Öhlins dealer if you
    preload
    have any questions about setting up.
    adjuster

    Rebound
    damping
    adjuster

    Length
    adjuster

    SETUP DATA
    Length 315+3/-3 mm Recommended free sag and ride height
    Stroke 58 mm R1-R3 32 mm
    Rebound 16 clicks F1-F3 43 mm
    Compression 13 clicks
    Spring (part no.) 21041-29
    Spring preload 14 mm
    Spring rate 90 N/mm
    Spring free length 150 mm

    Öhlins products are subject to To find the latest information Part no. MI_YA968_0
    continuous improvement and contact an Öhlins distributor. Issued 2021-11-16
    development, therefore, although Please contact Öhlins if you have
    these instructions include the most any questions regarding the
    up-to-date information available at contents in this document.
    the time of printing, minor updates
    may occur.

    © Öhlins Racing AB. All rights Öhlins Racing AB


    reserved. Any reprinting or Box 722
    unauthorized use without the written S-194 27 Upplands Väsby, Sweden
    permission of Öhlins Racing AB Phone +46 8 590 025 00
    is prohibited. fax +46 8 590 025 80

    You might also like