2

Supercast PVC ID- MAR. 2017

Waterstop Range constructive solutions

Centrally and externally placed

PVC waterstops

Uses

The Supercast range of PVC waterstops is designed to The range consists of centrally placed profiles; Supercast
provide an integral sealing system for movement and Hydrofoil, Supercast Watafoil; and externally placed profiles;
construction joints in concrete cast in-situ. These joints Supercast Rearguard S, Supercast Rearguard R, Supercast
typically occur in the following types of structure: Rearguard Kicker and Supercast Angleguard.

Water retaining Standards compliance

 
 Reservoirs, water towers and sewage tanks Supercast PVC waterstops are suitable for use in contact
  with potable water. “Water Byelaws Scheme approved
 Dams, culverts, canals and spillways product”: listing number 8804054.
 
 Swimming pools Description
 
Bundled areas surrounding liquid retaining tanks
Supercast waterstops are extruded from a high grade PVC
Water excluding compound which has been formulated to give excellent
  flexibility and longevity characteristics. They are available as
 Basements and underground car parks straight lengths and factory produced intersections or as a
  factory prefabricated segment of a network to minimize site
 Tunnels and subways jointing.
 
 Abutments and retaining walls Principles of waterstop function
 
Roof decks and podium areas Supercast waterstops work because of two specific aspects
of their design.
Advantages
  a) Valve principle
 Range of profiles to suit every need
Simple waterstop profiles based on dumbells are cast
 
 Fully continuous 4 bulbed network into the edges of adjacent concrete panels, which act
as baffles. In the event of joints opening as drying
 
 Reinforced eyeleted edge flanges for positive fixing shrinkage or other movement occurs, the edge bulbs of
the profile act as anchors. These induce tensions
 
 Simple on-site jointing across the waterstop resulting in a sealing effect at the
inner faces of the edge bulbs.
 
 Full range of moulded and fabricated intersection pieces
 
Special grades for Hydrocarbons resistant applications

Page 1
 2
Supercast PVC ID- MAR. 2017
Waterstop Range
Supercast Hydrofoil

Centre bulb sections are used in expansion, contraction and

construction joints. The centre bulb allows for movements in
a structure to be accommodated whilst its hexagonal deign
provides a flat surface. This allows shuttering and joint fillers
to fit snugly.

The 330 mm profile is specially designed for use in roof slabs

b) Tortuous path principle where a greater degree of movement may occur particularly
during construction.
Profiles with a more complex cross section have a
much greater surface area. They present a much Hydrofoil sections
greater resistance and more difficult path for water to
seep around the section.

The Supercast range incorporates both of these principles.

The products offer a fully continuous 4 bulbed design
maintaining both the valve and tortuous path principles.
These principles are maintained in the transition from
Rearguard profiles in floors to centrally placed profiles in
walls.
Supercast Watafoil

Plain web sections are used in construction and contraction

joints.

Watafoil sections

Design criteria

The choice of the width and thickness of waterstop is largely

governed by concrete thickness, the position of the
reinforcement, aggregate size and complexity of the pour.

In general the 250 mm width of waterstop is suited to wall

thicknesses of 250 mm and over. For concrete less than All centrally placed Supercast waterstops incorporate an
250 mm thick, the use of a narrower waterstop eyeletted, reinforced edge flange. This enables them to be
approximating to the wall thickness will be appropriate. easily positioned by wiring to surrounding reinforcement.

Page 2
constructive solutions
 2
Supercast PVC ID- MAR. 2017

Waterstop Range
Supercast Rearguard R Supercast Angleguard

Plain web sections, which are placed externally, for use in An externally placed waterstop for use where the joint line
contraction and construction joints. They incorporate a coincides with a change in level of the slab soffit. The profile
central fin to assist setting out shutter location. is designed to co-ordinate with the 250 mm Rearguard S
profile.

Dimensions are approximate and subject to manufacturing

tolerances Heavy duty sections (XHD) currently not available in
SEA
Supercast Rearguard S
Increased web thickness gives a much stiffer section. The
Sections incorporate a flat top center box, which allows stiffened profile is used where large volumes of concrete are
movement to be accommodated in expansion joints. The being placed. They are used where concrete is being placed
box also provides a seating to support joint fillers. from a great height such as deep wall shutters.

XHD Rearguard R

All Rearguard sections incorporate a nailing flange with a

reinforced edge to provide a secure fixing that will resist
tearing.
XHD Rearguard S
Supercast Rearguard Kicker

An extra wide version of Rearguard R profile which is used

to seal wall/kicker joints where the concrete kicker is being
cast after the slab rather than monolithically with the slab.
The extra width enables the waterstop to span both the joint XHD Rearguard SLX
between kicker and slab as well as the joint between kicker

Dimensions are approximate and subject to manufacturing

tolerances

Page 3
constructive solutions
 2
Supercast PVC ID- MAR. 2017

Waterstop Range

Page 4
constructive solutions
 2
Supercast PVC ID- MAR. 2017
Waterstop Range
Centrally placed waterstop Installation instructions

These waterstops are positioned within the thickness of the Supercast Hydrofoil and Watafoil
concrete components and as a result are supported by
concrete on both sides. They are therefore able to withstand Waterstops must be installed so that they are securely held
water pressure from either side. This makes them suitable in their correct position while the concrete is being placed.
for use in water retaining structures. They will prevent loss Concrete must be fully compacted around the waterstops to
of water from within the tank and will prevent ingress of ensure that no voids or porous areas remain. Where
ground water when the tank is drained down. reinforcement is present, an adequate clearance must be left
to permit proper compaction.
Externally placed waterstop
The brass eyelets used for securing the waterstop are
These waterstops are designed for use in basement, located outside the edge bulbs so as not to create water
foundation and floor slab construction in vertical and paths around the profile.
horizontal joints in both water retaining and water excluding
structures. When used in walls, externally placed waterstops Example of a kicker joint
will only resist water pressure from the face to which they
are fixed. When used below floor slabs, where the waterstop
is supported by the blinding concrete or when placed in
vertical situations against permanent concrete shuttering,
externally placed waterstops will resist water pressure from
either face.

Properties

Profiles

Form: Extruded thermoplastic

sections
Colour: Blue
Hydrostatic head: Up to 100 m (10 bar)
Joint movement:
Hydrofoil (standard & XHD): up to 10 mm
Rearguard S (standard & XHD): up to 40 mm
Rearguard SLX XHD up to 60 mm Supercast Rearguard
PVC Compound When used on ground slabs where the waterstop is
o
Typical figures: To BS 2782 at 25 C supported on blinding, Rearguard profiles usually require no
2
Tensile strength: > 15 N/mm fixing. Lay the waterstop centrally over the line of the joint to
Elongation at break: > 300% be formed.
Hardness: Shore „A‟ 80 to 90
Fixing to vertical shuttering is done by nailing through the
Specification clauses outer nailing flanges leaving the head of the nail proud so
that it is held in the cured concrete. This prevents the
waterstop being displaced when the shuttering is struck.
1. Supplier specification
Fixing to vertical shutter
Where indicated on the drawings, PVC waterstops shall
be Supercast Waterstops obtained from Fosroc
(address as shown). All wall/floor waterstop
connections shall be made using Supercast injection
moulded transition pieces to ensure continuity of the
four bulb profiles.

2. Performance specification

Where indicated on the drawings, PVC waterstops shall

be made from extruded plasticised PVC compound.
The compound used shall meet the US Corps of
Engineers specification CRD-C 572-74. it shall have a
tensile strength in excess of 14 MN/m2 and an
elongation at break in excess of 300%.

Page 5
constructive solutions
 2
Supercast PVC ID- MAR. 2017

Waterstop Range
Fixing Supercast Kicker Waterstop Intersection pieces

In addition to nailing to the external shutter, the Kicker Standard intersection pieces are available for each
profile is equipped with brass eyelets in the central rib. Twist Supercast waterstop profile. The standard on-flat intersection
short lengths of tying wire through these eyelets so that leg length is 230 mm from centre line. On-edge intersections
when the kicker is cast they act as anchors, holding the have a standard 75 mm leg length.
center of the waterstop tight against the face of the
concrete. This prevents the build-up of debris between the Factory welded intersections for Supercast Hydrofoil /
waterstop and the kicker prior to the wall being poured. Watafoil ad XHD Hydrofoil / Watafoil.

Supercast Angleguard

Fixing in position is done in a similar manner to Supercast

Rearguard.

Site jointing instructions

Jointing of Supercast waterstops is carried out using Fosroc

Heat Welding Equipment. The ends to be joined are cut
square and held in alignment in a special jig. The ends are
then pressed either side of a special heated blade, until an
even, molten bead of PVC appears around the section. The
heated blade is then removed and the molten ends pressed
fully together. The PVC cools to form a strong fusion welded
joint. Full instructions are available from Fosroc.

Fosroc PVC heat welding equipment

Page 6
constructive solutions
 2
Supercast PVC ID- MAR. 2017

Waterstop Range
Estimating Precautions

Section Minimum radii Roll Health and safety

Supercast Width in On flat On edge Length
(mm) (m) (m) (m) Hot weld site jointing of PVC waterstops results in the
Hydrofoil 330 20 0.15 12 liberation of hydrogen chloride mist and vapour. The OEL
250 15 0.15 12 (operational exposure limit) of 5 ppm can be exceeded in still
200 14 0.15 15 air confined spaces, therefore forced ventilation must be
150 12 0.075 15 provided or a suitable respirator used.
Watafoil 250 15 0.15 12
200 14 0.15 15
150 12 0.075 20
Rearguard R 250 10 N/A 12
200 9 N/A 15
150 8 N/A 12 & 20
Rearguard S 250 10 N/A 12
200 9 N/A 12
150 8 N/A 12
Rearguard
Kicker 300 20 N/A 12
Angleguard 250 10 N/A 3m
girth lengths
XHD
Hydrofoil 250 15 0.23 10
XHD
Watafoil 250 15 0.23 10
XHD
Rearguard R 250 15 0.23 10
XHD
Rearguard S 250 15 0.23 10
XHD
Rearguard 250 15 0.23 5
SLX

Equipment

Jointing jigs

150 mm Supercast Rearguard R & S

200 mm Supercast Rearguard R & S
250 mm Supercast Rearguard R & S
330 mm Supercast Rearguard Kicker
150 mm Supercast Hydrofoil & Watafoil
200 mm Supercast Hydrofoil & Watafoil
250 mm Supercast Hydrofoil & Watafoil
250 mm Supercast XHD Hydrofoil & Watafoil
330 mm Supercast Hydrofoil

Heater blades

110v and 220v, 350w blades are available.

Warning:
Ensure that heater blades are earthed by the
green/yellow wire.

Page 7
constructive solutions
 2
Supercast PVC ID- MAR. 2017

Waterstop Range constructive solutions

Technical support

Fosroc offers a comprehensive range of high performance

high quality; construction products all backed by BS 5750
certification. Fosroc offers a technical support package to
specifiers and contractors which include computer-aided
design (CAD), standard details and technical advice from
staff with unrivalled experience in the industry.

Additional information

Application at low temperatures

Care in the handling and installation of Supercast PVC

waterstops is necessary at low ambient temperatures. Such
temperatures will also require special precautions to be
taken with the placing and curing of concrete.

Fosroc manufactures a wide range of complementary

products which include:

Waterproofing membranes & waterstops

Joint sealants & filler boards

Cementitious & epoxy grouts

Specialised flooring materials

Fosroc additionally offers a comprehensive package of

products specifically designed for the repair and
refurbishment of damaged concrete. Fosroc‟s „Systematic
Approach‟ to concrete repair features the following:

Hand-placed repair mortars

Spray grade repair mortars

Fluid micro-concretes

Chemically resistant epoxy mortars

Anti-carbonation/anti-chloride protective coatings

Chemical and abrasion resistant coatings

For further information on any of the above, please consult

your local Fosroc office - as below.

Important note
Fosroc products are guaranteed against defective materials and manufacture and are sold subject to its standard
Conditions for the Supply of Goods and Services, copies of which may be obtained on request. Whilst Fosroc
endeavours to ensure that any advice, recommendation, specification of information it may give is accurate and

PT. FOSROC
correct, it cannot, because it has no direct or continuous control over where or how its products are applied, accept
any liability either directly or indirectly arising from the use of its products, whether or not in accordance with any

Indonesia
advice, specification, recommendation of information given by it.

Jl.Akasia II Blok A8 No.1

Delta Silicon Industrial Park telephone: fax: email:
Lippo Cikarang +62 21 897 2104-06 +62 21 897 2107 Indonesia@Fosroc.com
Bekasi 17550
Indonesia
www.fosroc.com
Page 8