Iso 17850 2015

INTERNATIONAL ISO
STANDARD 17850
First edition
2015-07-01
Photography — Digital cameras

— Geometric distortion (GD)
measurements
Photographie — Caméras numériques — Mesurages de distorsion
géométrique (DG)
iTeh STANDARD PREVIEW

(standards.iteh.ai)
ISO 17850:2015
https://standards.iteh.ai/catalog/standards/sist/c72e4da2-b21a-4931-ae96-
df8a9d54d63f/iso-17850-2015
Reference number
ISO 17850:2015(E)
© ISO 2015
ISO 17850:2015(E)


(standards.iteh.ai)
ISO 17850:2015
df8a9d54d63f/iso-17850-2015
COPYRIGHT PROTECTED DOCUMENT

© ISO 2015, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2015 – All rights reserved

ISO 17850:2015(E)

Contents Page
Foreword......................................................................................................................................................................................................................................... iv
Introduction...................................................................................................................................................................................................................................v
1 Scope.................................................................................................................................................................................................................................. 1
2 Normative references....................................................................................................................................................................................... 1
3 Terms and definitions...................................................................................................................................................................................... 1
4 Measurement methods................................................................................................................................................................................... 2
4.1 General............................................................................................................................................................................................................ 2
4.2 Local geometric distortion............................................................................................................................................................. 3
4.3 Line geometric distortion............................................................................................................................................................... 3
5 Requirements........................................................................................................................................................................................................... 4
5.1 Apparatus and hardware................................................................................................................................................................. 4
5.2 Lighting........................................................................................................................................................................................................... 4
5.3 Dot chart........................................................................................................................................................................................................ 5
5.3.1 Design and characteristics....................................................................................................................................... 5
5.3.2 Requirement for the chart planarity................................................................................................................ 6
5.4 Grid chart...................................................................................................................................................................................................... 7
5.4.1 Design and characteristics....................................................................................................................................... 7
5.5 Image/camera settings..................................................................................................................................................................... 8
5.5.1 General...................................................................................................................................................................................... 8
5.5.2 iTeh STANDARD PREVIEW
Basic settings and influencing factors............................................................................................................ 8
5.5.3 Specific test procedures.............................................................................................................................................. 8
5.5.4
(standards.iteh.ai)
Positioning of the camera.......................................................................................................................................... 8
5.5.5 Exposure, white balance, and focus.................................................................................................................. 9
ISO 17850:2015
6 Determination of geometric distortion......................................................................................................................................10
6.1 Local geometric distortion .......................................................................................................................................................... 10
df8a9d54d63f/iso-17850-2015
6.1.1 Numerical definition................................................................................................................................................... 10
6.1.2 Outline of the practical algorithm................................................................................................................... 10
6.2 Line geometric distortion............................................................................................................................................................ 11
6.2.1 Horizontal line distortion....................................................................................................................................... 11
6.2.2 Vertical line distortion.............................................................................................................................................. 12
6.2.3 Total line distortion..................................................................................................................................................... 12
7 Presentation of results.................................................................................................................................................................................13
7.1 General......................................................................................................................................................................................................... 13
7.2 Local geometric distortion.......................................................................................................................................................... 13
7.3 Line geometric distortion............................................................................................................................................................ 14
Annex A (informative) Illustrative example and validation.......................................................................................................15
Annex B (informative) Extracting the dots from the target........................................................................................................17
Annex C (informative) Dot centre validation.............................................................................................................................................25
Annex D (informative) Grid sort..............................................................................................................................................................................30
Annex E (informative) Example of subjective evaluation.............................................................................................................40
Bibliography.............................................................................................................................................................................................................................. 48
© ISO 2015 – All rights reserved iii

ISO 17850:2015(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity
assessment, as well as information about ISO’s adherence to the WTO principles in the Technical Barriers
to Trade (TBT) see the following URL: Foreword - Supplementary information
(standards.iteh.ai)
The committee responsible for this document is ISO/TC 42, Photography.
ISO 17850:2015
df8a9d54d63f/iso-17850-2015
iv © ISO 2015 – All rights reserved

ISO 17850:2015(E)

Introduction
A digital still camera (DSC) typically employs a taking lens that is a rotationally symmetric optical
system. Generally, the function of rotationally symmetric optical systems is to form an image that is
geometrically similar to the object except some particular systems, such as fish-eye lenses and eyepieces,
where this condition is deliberately not maintained. This function is accomplished ideally according to
the geometry of perspective projection. Departures from the ideal image geometry are called distortion.
The distortion is a position-dependent quantity which generally has a vectorial character. In a given
image plane (which may also lie at infinity), this vector, representing the difference between theoretical
and real image position, has a radial and a tangential component. In optical systems, the tangential
component is basically conditioned by imperfect rotational symmetry. The systems manufactured in
accordance with the present state of the art have a negligible tangential distortion.
Geometric distortion (GD) of DSCs is mainly caused by the variation of magnification in the image field of
the camera lens. The most well-known effect of distortion is that straight lines appear curved. Generally
speaking, the proportions between objects are not preserved in a distorted image, which can be very
unpleasant for some natural scenes, architecture, or portraits. Distortion is fully described by a 2D map,
giving the displacement from a point in an ideal undistorted image to the point in the actual distorted
image. The image centre is usually assumed to be undistorted; the magnification factor at this position
actually defines the focal distance.
Different types of distortion are usually characterized by how the magnification radially varies within
the image field. Barrel and pincushion are the most usual types of distortion for which magnification
is respectively monotonously decreasing and monotonously increasing when moving along from the
centre to the border of the image field. Other types which cannot be categorized into above two types
are usually called wave distortion.
(standards.iteh.ai)
ISO 17850:2015
df8a9d54d63f/iso-17850-2015
a) Barrel (or negative) distortion
b) Pincushion (or positive) distortion
NOTE The magnification is decreasing for barrel distortion and increasing for pincushion.
Figure 1 — Two main types of distortions
© ISO 2015 – All rights reserved v

ISO 17850:2015(E)

ISO 9039 defines methods to measure a lens that is separated from a camera. On the other hand, this
International Standard was developed and defines methods to measure the total image distortion of a
camera including a lens and signal processing.
This International Standard is based on both Reference [3] prepared by the Camera Phone Image Quality
(CPIQ) group within the International Imaging Industry Association (I3A) and Reference [4] prepared
by Camera and Imaging Products Association (CIPA).

(standards.iteh.ai)
ISO 17850:2015
df8a9d54d63f/iso-17850-2015
vi © ISO 2015 – All rights reserved

INTERNATIONAL STANDARD ISO 17850:2015(E)
Photography — Digital cameras — Geometric distortion

(GD) measurements
1 Scope
This International Standard specifies a protocol to measure geometric distortion of a digital camera. It
is applicable to the measurement of digital cameras including camera phones.
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
ISO 14524, Photography — Electronic still-picture cameras — Methods for measuring opto-electronic
conversion functions (OECFs).
IEC 61146-1, Video cameras (PAL/SECAM/NTSC) — Methods of measurement — Part 1: Non-broadcast
single-sensor cameras
EBU Tech3249, Measurement and analysis of the performance of film and television camera lenses
(standards.iteh.ai)
3 Terms and definitions
ISO 17850:2015
3.1 https://standards.iteh.ai/catalog/standards/sist/c72e4da2-b21a-4931-ae96-
geometric distortion df8a9d54d63f/iso-17850-2015
GD
<of DSC> displacement from the ideal shape of a subject (lying on a plane parallel to the image plane) in
the recorded image
Note 1 to entry: Geometric distortion basically derives from variation of lateral magnification in the image field of
a camera lens and results in straight lines being rendered as curves. There are other factors to induce geometric
distortion, for example, rotational asymmetricity of a camera lens or position shift processing in a camera imaging
process.
3.2
image height
3.2.1
image height
<of DSC> distance between an image point and the centre of the image area or its relative expression
which is the value normalized by one half of the diagonal of the image area
Note 1 to entry: This is an extension of the definition in ISO 9039 which is a measurement for optical systems.
3.2.2
actual image height
<of DSC> image height of an actual recorded image point in the recorded image area
Note 1 to entry: “Actual recorded image point” corresponds to “observed image point” in ISO 9039.
Note 2 to entry: “Image height” in ISO 9039 basically means “actual image height” but the usage is sometimes
confusing.
© ISO 2015 – All rights reserved 1

ISO 17850:2015(E)

Note 3 to entry: The adjective “actual” is used in similar meaning, “actual point” and “actual position”, for example.
3.2.3
ideal image height
<of DSC> image height of a theoretical corresponding point in the recorded image area, assuming a
geometrically undistorted image formation
Note 1 to entry: This is an extension of the definition in ISO 9039 which is a measurement for optical systems.
Note 2 to entry: The adjective “ideal” is used in similar meaning, “ideal point” and “ideal position”, for example.
3.3
image quality
impression of the overall merit or excellence of an image, as perceived by an observer neither associated
with the act of photography nor closely involved with the subject matter depicted
Note 1 to entry: The purpose of defining image quality in terms of third-party (uninvolved) observers is to
eliminate sources of variability that arise from more idiosyncratic aspects of image perception and pertain to
attributes outside the control of imaging system designers.
3.4
noise
unwanted variations in the response of an imaging system
3.5
resolution
measure of the ability of a digital image capture system or a component of a digital image capture system
to distinguish picture detail
3.6
(standards.iteh.ai)
TV distortion ISO 17850:2015
line distortion measured https://standards.iteh.ai/catalog/standards/sist/c72e4da2-b21a-4931-ae96-
by conventional method of TV field defined in IEC 61146-1 (24 Geometric
distortions) or EBU Tech3249 (2.11. Picturedf8a9d54d63f/iso-17850-2015
height distortion)
4 Measurement methods
4.1 General
As defined in 3.1, geometric distortion basically derives from the variation of magnification in the image
field. If this phenomenon occurs in an image, it means that a regular structure in an object does not
appear to be regular in the image taken with the camera. There are two ways defined in this International
Standard to quantify the amount of geometric distortion in an image. Both have their pros and cons.
2 © ISO 2015 – All rights reserved

ISO 17850:2015(E)

Figure 2 — Regular grid (solid lines) in the scene is distorted and the red diamonds mark the
position of the intersections in the image produced by the camera
(standards.iteh.ai)
4.2 Local geometric distortion ISO 17850:2015
Geometric distortion can be measured on a white chart containing black dots at the position of a regular
df8a9d54d63f/iso-17850-2015
grid or on a grid chart formed by straight lines. The local geometric distortion method analyses the grid
formed by the test chart in the centre of the image and calculates the ideal positions of the structure
based on the measured distances. After that, it analyses the rest of the image and locates all actual
positions of the grid. The distance between the ideal position and the actual position is the geometric
distortion at that location in the image.
The distance between the two positions can be plotted as a function over the distance to the image
centre. This curve indicates the variation of image magnification versus the actual image height, which
is an expression of the geometric distortion called local geometric distortion. In order to limit the result
to a single value that might get reported with the cameras specifications, the maximum (peak to peak)
value shall be reported.
The manufacturing tolerances, such as lens tilt or off-centring, can result in a non-rotationally symmetric
GD behaviour. If the system is not rotationally symmetric, it can lead to increased distortion levels in the
image corners. In this case, the measured geometric distortion is correct for the camera under test but
might not represent a standard camera of the tested model.
4.3 Line geometric distortion

The principle of line geometric distortion is to measure the bending of a straight horizontal or vertical
line at defined distances from the image centre and to report the maximum of the measured bending.
This bending is preferably measured on a chart with a regular line grid.

ISO 17850:2015(E)

Line geometric distortion is the direct measured result of this method and it is easy to understand
intuitively for consumers. However, it can also be interpreted from the measured result using the local
geometric distortion method.
NOTE The line geometric distortion has a long history and it has been used in the video technology for
decades. The reason is that it was easy to determine this value with standard measurement equipment used in the
analogue video world. The fundamental concept of this method was first standardized by the IEC in IEC 61146–1
in 1994.
5 Requirements
5.1 Apparatus and hardware

The following hardware is necessary to control and report the test conditions:
— dot target or a grid chart;
— two light sources;
— device to measure the chart height captured in the image;
— mirror (for camera alignment with the target).
5.2 Lighting
Lighting uniformity is recommended to ease the processing of the target but does not influence the
phenomenon of distortion. The light sources should be adjusted such that illumination is uniform on the
(standards.iteh.ai)
target at ±10 %. Light sources should be baffled to prevent the direct illumination of the camera. The
light sources should be located so as to minimize the occurrence of specular reflections off the surface
of the target when viewed by the camera under test. ISO 17850:2015
The illumination should be set so that thedf8a9d54d63f/iso-17850-2015
auto-exposure of the camera gives a suitable result. More
precisely, the image should not be clipped in either bright or dark parts of the target. The camera should
be positioned so that it casts no shadow on the chart.

ISO 17850:2015(E)

~45° ~45°
2 2
Key
1 test target
2 illumination iTeh STANDARD PREVIEW
3 camera
(standards.iteh.ai)
Figure ISO317850:2015
— Lighting system
df8a9d54d63f/iso-17850-2015
5.3 Dot chart
5.3.1 Design and characteristics
The test chart contains black circular dots placed on a perfectly regular square grid on a uniform white
background.
The dot centres may be connected by straight black lines with a thickness of approximately 1/10 of the
dot diameter as shown in Figure 4 b). That way, it does not affect the dot detection but helps to better
align the camera to the chart for example, by eliminating rotation between the chart and camera’s image
sensor axes. The straight black lines are especially useful if the mirror method described in 5.5.4 is not
possible or available.
The chart can be either a reflective test chart, which is front illuminated, or a transparency test chart,
which is rear illuminated. The chart contrast level should at least be 40:1 and not be higher than 10 000:1.
The size and the number of dots should depend on the resolution of the camera and the shooting distance.
The chart shall be shot compliant with the condition specified in 5.5.3.

ISO 17850:2015(E)

a) Simple dot chart b) Dot chart with connecting lines
Figure 4 — Dot chart
5.3.2 Requirement for the chart planarity
Non-planarity can be caused by bending of a chart.

Requirement for the chart planarity is as follows.
Surface deviation which is a height or depth from the reference plane [indicated as bending “a” in
(standards.iteh.ai)
Figure 5 a)] shall be less than 1,5 % of the width of the chart.
The required accuracy for a specific measurementISO sets the requirement for the chart planarity as follows.
17850:2015
For small bending, c is equal to half the width of the chart to which all numbers are normalized. If
df8a9d54d63f/iso-17850-2015
bending a occurs in a chart, the effective chart width seen by the camera is b. The difference between c
and b causes the deviation in % measured due to the bending of the chart and calculated by (1-b/c) × 100.
The standard requirement for local geometric distortion measurement should be a maximum error of
0,045 % due to deviation in planarity of the chart. This equals a maximum deviation in planarity of 3 %.
And 3 % of half the width equals to 1,5 % of the full width of the chart.

ISO 17850:2015(E)

Deviation a/c b/c = Deviation of

in % cos (sin-1 a/c) measured
distortion in %
0,5 0,005 0,999 987 0,001 3
1 0,01 0,999 950 0,005 0
2 0,02 0,999 800 0,020 0
3 0,03 0,999 550 0,045 0
4 0,04 0,999 200 0,080 0
5 0,05 0,998 749 0,125 1
6 0,06 0,998 198 0,180 2
8 0,08 0,996 795 0,320 5
9 0,09 0,995 942 0,405 8
10 0,1 0,994 987 0,501 3

a) Explanation of the parameters b) Table of numerical relation
(standards.iteh.ai)
Figure 5 — Explanation for the chart planarity and its effect on measured value
ISO 17850:2015
5.4 Grid chart df8a9d54d63f/iso-17850-2015
5.4.1 Design and characteristics
Figure 6 — Line grid pattern chart
The line grid pattern chart shown in Figure 6 is an example of a test chart for line distortion. The
horizontal and vertical lines of the grid shall be located between reference lines at no less than 1,0, 0,9,
0,8, 0,7, and 0,6 times the distance between the pairs of reference lines with the tolerance of ±2 %. The
pairs of reference lines are the sides of the outermost rectangle.

ISO 17850:2015(E)

The chart shall be shot compliant with the condition specified in 5.5.3.
All other aspects regarding size and contrast shall be as described for the dot chart in 5.3.
5.5 Image/camera settings
5.5.1 General
Set the camera at minimal gain to minimize noise (if possible). All special colour modes or tone mode
should be deactivated. Quality factors, if available, should be set to their maximum.
5.5.2 Basic settings and influencing factors
The magnification is an important factor in measuring the distortion. The standard shooting distance
should be 30 times the focal length equivalent to 35 mm film camera. This means that a chart height of
720 mm fills the complete image. If the chart height differs more than 30 % from this requirement, the
chart height captured in the image shall be reported together with the results.
The camera shall be accurately focused on the chart.
Since distortion depends on the wavelength, it also depends on the illuminant and the spectral responses
of the sensor. Only the distortion on the green channel shall be reported.
5.5.3 Specific test procedures

5.5.3.1 Local geometric distortion
(standards.iteh.ai)
The chart shall be shot so that
ISO 17850:2015
— chart shall fill the fieldhttps://standards.iteh.ai/catalog/standards/sist/c72e4da2-b21a-4931-ae96-
of view,
— number of dots should be no less than df8a9d54d63f/iso-17850-2015
15 dots in height and the related number of dots depending
on the image aspect ratio (for 4:3, 20×15 dots; for 3:2, 23×15) to form a regular grid,
— diameter of each dot should be no less than 10 pixels, and
— in case of reporting the single value as ISO local geometric distortion (see 7.2), and when using the
method of measuring actual dots, the corner 4 dots in the output image shall be positioned so that
the centre of each dot is on a vertex of the frame of the output image with the tolerance of 0 %, −2 %
(i.e. the centre of each dot is positioned from 98 % to 100 % at the actual image height).
5.5.3.2 Line geometric distortion
The chart shall be shot so that each reference line pair inscribes the frame of the output image with the
tolerance of 0 %, −2 % (i.e. the contact points of the reference line pair and the frame are positioned from
98 % to 100 % at the picture height or at the picture width).
5.5.4 Positioning of the camera
The chart shall be orthogonal to the optical axis. The alignment can be performed by using a mirror set
up on the target plane (i.e. parallel to the target plane), as shown in Figure 7.
Pan, tilt, and laterally displace the camera position to the left, right, up, and down until the centre point
of the taking lens in the viewfinder image is positioned at the image centre.

ISO 17850:2015(E)

Figure 7 — Alignment of the camera with the target plane using a mirror
If the mirror is not available or(standards.iteh.ai)
the positioning method is not applicable, a manual alignment using
the straight lines in the chart shall be performed so that the intersection of the central horizontal and
vertical lines of the chart is in the centre ofISO the17850:2015
image. For each horizontal/vertical line, the lines shall be
oriented “parallel” https://standards.iteh.ai/catalog/standards/sist/c72e4da2-b21a-4931-ae96-
to the horizontal/vertical image borders meaning that the line shall be at the same
image height for the same distancesdf8a9d54d63f/iso-17850-2015
from the vertical/horizontal centre of the image.
5.5.5 Exposure, white balance, and focus
The exposure shall be set by automatic exposure or set to an exposure level such that the uniform white
background becomes 110 to 160 (8-bit digital).
For a colour camera, the white balance shall be in a variable white balance mode or an automatic white
balance mode. The camera white balance should be adjusted, if possible, to provide proper white balance
for the illumination light source as specified in ISO 14524.
The focusing shall be adjusted in focus by a proper way, for example, a manual-focusing mode or an auto-
focusing mode.

Iso 17850 2015

Uploaded by

Copyright:

Available Formats

Iso 17850 2015

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Iso 17850 2015

Uploaded by

Copyright:

Available Formats

INTERNATIONAL ISO

Photography — Digital cameras

iTeh STANDARD PREVIEW

iTeh STANDARD PREVIEW

COPYRIGHT PROTECTED DOCUMENT

ii ﻿ © ISO 2015 – All rights reserved

© ISO 2015 – All rights reserved ﻿ iii

iv ﻿ © ISO 2015 – All rights reserved

a) Barrel (or negative) distortion

b) Pincushion (or positive) distortion

Figure 1 — Two main types of distortions

© ISO 2015 – All rights reserved ﻿ v

iTeh STANDARD PREVIEW

vi ﻿ © ISO 2015 – All rights reserved

Photography — Digital cameras — Geometric distortion

© ISO 2015 – All rights reserved ﻿ 1

2 ﻿ © ISO 2015 – All rights reserved

4.3 Line geometric distortion

© ISO 2015 – All rights reserved ﻿ 3

5.1 Apparatus and hardware

4 ﻿ © ISO 2015 – All rights reserved

5.3.1 Design and characteristics

© ISO 2015 – All rights reserved ﻿ 5

a) Simple dot chart b) Dot chart with connecting lines

Figure 4 — Dot chart

5.3.2 Requirement for the chart planarity

Non-planarity can be caused by bending of a chart.

6 ﻿ © ISO 2015 – All rights reserved

Deviation a/c b/c = Deviation of

0,5 0,005 0,999 987 0,001 3

1 0,01 0,999 950 0,005 0

2 0,02 0,999 800 0,020 0

3 0,03 0,999 550 0,045 0

4 0,04 0,999 200 0,080 0

5 0,05 0,998 749 0,125 1

6 0,06 0,998 198 0,180 2

8 0,08 0,996 795 0,320 5

9 0,09 0,995 942 0,405 8

10 0,1 0,994 987 0,501 3

iTeh STANDARD PREVIEW

5.4.1 Design and characteristics

Figure 6 — Line grid pattern chart

© ISO 2015 – All rights reserved ﻿ 7

5.5 Image/camera settings

5.5.2 Basic settings and influencing factors

5.5.3 Specific test procedures

5.5.3.2 Line geometric distortion

5.5.4 Positioning of the camera

8 ﻿ © ISO 2015 – All rights reserved

5.5.5 Exposure, white balance, and focus

© ISO 2015 – All rights reserved ﻿ 9

You might also like

ii © ISO 2015 – All rights reserved

© ISO 2015 – All rights reserved iii

iv © ISO 2015 – All rights reserved

© ISO 2015 – All rights reserved v

vi © ISO 2015 – All rights reserved

© ISO 2015 – All rights reserved 1

2 © ISO 2015 – All rights reserved

© ISO 2015 – All rights reserved 3

4 © ISO 2015 – All rights reserved

© ISO 2015 – All rights reserved 5

6 © ISO 2015 – All rights reserved

© ISO 2015 – All rights reserved 7

8 © ISO 2015 – All rights reserved

© ISO 2015 – All rights reserved 9