SANS10019 2011 Ed7

Copyright protected.
This standard is exclusively for Peter Herman of Stingray for use on the local drive of your Personal Computer with access only for your
personal use. No local area network, wide area network, intranet or internet storage and access is permitted. You can make one paper copy of the standard.
No paper copy may be photocopied or reproduced in any way.
ISBN 978-0-626-26055-2
SANS 10019:2011
Edition 7
SOUTH AFRICAN NATIONAL STANDARD
Transportable pressure receptacles for

compressed, dissolved and liquefied
gases — Basic design, manufacture,
use and maintenance
Published by SABS Standards Division

1 Dr Lategan Road Groenkloof Private Bag X191 Pretoria 0001
Tel: +27 12 428 7911 Fax: +27 12 344 1568
www.sabs.co.za
© SABS
© SABS. Single-user licence only; copying and networking prohibited. Note that only one printout of the standard may be made.
Copyright protected. This standard is exclusively for Peter Herman of Stingray for use on the local drive of your Personal Computer with access only for your
SANS 10019:2011
Edition 7
Table of changes
Change No. Date Scope
Foreword
This South African standard was approved by National Committee SABS TC 58, Vessels under
pressure, in accordance with procedures of the SABS Standards Division, in compliance with annex 3 of
the WTO/TBT agreement.
This document was published in September 2011.
This document supersedes SANS 10019:2008 (edition 6).
This document was written in order to support a specific South African Regulation and, of necessity,
includes references to South African legislation. It therefore might not be suitable for direct application in
other jurisdictions where conflicting legislation exists.
Reference is made in 3.2 and 3.30 to “the relevant national legislation”. In South Africa this means
section 3 of the Accreditation for Conformity Assessment, Calibration and Good Laboratory Practice Act,
2006 (Act No. 19 of 2006).
Reference is made in 3.6(a) to “relevant national legislation”. In South Africa this means the
Occupational Health and Safety Act, 1993 (Act No. 85 of 1993).
Reference is made in 3.6(b) to “relevant national legislation”. In South Africa this means the Mine Health
and Safety Act, 1996 (Act No. 29 of 1996).
Reference is made in NOTE 2 to 3.25, 4.1 (two references) and 8.7.1 to “relevant national legislation”. In
South Africa this means the Pressure Equipment regulations (PER) and Occupational Health and Safety
Act, 1993 (Act No. 85 of 1993).
Reference is made in 8.6.4 and 9.1.3 to “relevant national legislation”. In South Africa this means the
Regulations of the Trade Metrology Act, 1973 (Act No. 77 of 1973).
Reference is made in the NOTE to 9.5.1 to “relevant national legislation”. In South Africa this means the
Diving Regulation of the Occupational Health and Safety Act, 1993 (Act No. 85 of 1993).
Reference is made in 10.4.1.1 and 10.4.1.2 to “relevant national legislation”. In South Africa this means
the National Road Traffic Act, 1996 (Act No. 93 of 1996).
Reference is made in 10.5.1 to “relevant national legislation”. In South Africa this means the Hazardous
Chemical Substances Regulation 9a of the Occupational Health and Safety Act, 1993, (Act No. 85 of
1993).
Reference is made in 11.3 to “relevant national legislation”. In South Africa this means clause 24 of the
Occupational Health and Safety Act, 1993, (Act No. 85 of 1993).
Annexes A, A1, C, D and E form an integral part of this document. Annexes B and F are for information
only.
SANS 10019:2011
Edition 7
Contents
Page
Foreword
1 Scope .................................................................................................................................... 3
2 Normative references ............................................................................................................ 3
3 Definitions ............................................................................................................................. 6
4 Design and manufacturing requirements .............................................................................. 10
5 Valves ................................................................................................................................... 14
6 Pressure relief devices .......................................................................................................... 16
7 Revalidation of pressure receptacles .................................................................................... 18
8 Marking, labelling, colour coding and certificates ................................................................. 19
9 Filling of pressure receptacles .............................................................................................. 23
10 Handling, storage, transportation and use ............................................................................ 25
11 General safety precautions ................................................................................................... 26
Table 1 Reference temperatures ............................................................................................ 27
Table 2 Properties and pressure groups of permanent gases ............................................... 28
Table 3 Permanent gases: charging pressures and corresponding

developed pressures ................................................................................................ 29
Table 4 Permanent gases: developed pressures and corresponding

charging pressures ................................................................................................... 30
Table 5 High-pressure liquefiable gases ............................................................................... 31
Table 6 Low-pressure liquefiable gases ................................................................................ 33
Table 7 Class of pressure receptacles for specific gases ...................................................... 35
Table 8 Schedule of cylinder valve outlet connections for various gases .............................. 37
Table 9 Schedule of valve outlets for refrigerants class 2.2 .................................................. 38
Table 10 SCUBA cylinders outlet connections ........................................................................ 38
Table 11 Neck threads for cylinders ........................................................................................ 39
SANS 10019:2011
Edition 7
Contents (concluded)
Page
Table 12 Colour marking of gas cylinders ............................................................................... 40
Table 13 Refillable refrigerant cylinder colour chart ................................................................ 41
Table 14 Pre-fill inspection/rejection criteria for all cylinders other than

welded LPG cylinders ............................................................................................... 42
Table 15 Pre-fill inspection/rejection criteria for LPG welded steel cylinders .......................... 43
Annex A (normative) List of current approved manufacturing standards for the

importation and manufacture of gas pressure
receptacles in South Africa .................................................................. 44
Annex A1 (normative) List of special conditions applicable to current approved

manufacturing standards for the importation and manufacture
of gas pressure receptacles in South Africa ........................................ 50
Annex B (informative) Pressure receptacle valve standards .................................................. 51
Annex C (normative) Frequency of inspections and tests for pressure receptacles .............. 52
Annex D (normative) Schedule of SCUBA and SCBA cylinder colour coding and labels ..... 54
Annex E (normative) Placement of cylinders ......................................................................... 55
Annex F (informative) Developed pressure for permanent gases ........................................... 56
Bibliography .............................................................................................................................. 57
SANS 10019:2011
Edition 7
Transportable pressure receptacles for compressed, dissolved and

liquefied gases — Basic design, manufacture, use and maintenance
1 Scope
1.1 This standard covers the minimum requirements for the design, manufacture, use and maintenance
of refillable and non refillable pressure receptacles of water capacity 0,5 L to 3 000 L and cartridges of
> 0,5 L, and may include requirements over and above those contained within the cylinder design and
manufacturing standards (see annex A).
1.2 In addition to industrial, medical and domestic type pressure receptacles, this standard also covers
cylinders for self-contained underwater breathing apparatus (SCUBA) for recreational diving, self-
contained surface breathing apparatus (SCBA), fire-fighting extinguishers and fixed fire-fighting
extinguishing systems.
1.3 The standard covers the design requirements for CO2 and High Pressure Inert gas mixtures used in
portable and fixed fire-fighting systems, but excludes the operational performance requirements of
portable and fixed fire-fighting extinguishing systems (see SANS 1572 and SANS 1567).
1.4 It does not cover special pressure receptacles used in aircraft or air-brake reservoirs and SCUBA
cylinders for professional use.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies. Information on currently valid national and international
standards can be obtained from the SABS Standards Division.
ADR P200, Gas cylinders – Safe use of gas cylinders.
BS 341-1, Transportable gas container valves – Specification for industrial valves for working pressures
up to and including 300 bar.
BS 341-3, Transportable gas container valves – Valve outlet connections.
BS 341-4, Transportable gas container valves – Pressure relief devices.
CGA V1, Standard for compressed gas cylinder valve outlet and inlet connections.
SANS 10019:2011
Edition 7
ISO 7225, Gas cylinders – Precautionary labels.
ISO 10297, Transportable gas cylinders – Cylinder valves – Specification and type testing.
ISO 10920, Gas cylinders – 25E taper thread for connection of valves to gas cylinders – Specification.
ISO 11116-1, Gas cylinders – 17E taper thread for connection of valves to gas cylinders – Part 1:
Specification.
ISO 11117, Gas cylinders – Valve protection caps and valve guards for industrial and medical gas
cylinders – Design, construction and tests.
ISO 11621, Gas cylinders – Procedures for change of gas service.
ISO 11622, Gas cylinders – Conditions for filling gas cylinders.
ISO 13341, Transportable gas cylinders – Fitting of valves to gas cylinders.
ISO 13769, Gas cylinders – Stamp marking.
ISO 15995, Gas cylinders – Specifications and testing of LPG cylinder valves – Manually operated.
ISO 22434, Transportable gas cylinders – Inspection and maintenance of cylinder valves.
SANS 162/ISO 10286, Gas cylinders – Terminology.
SANS 199, Shut-off valves for refillable liquefied petroleum gas cylinders.
SANS 289, Labelling requirements for pre-packaged products (prepackages) and general requirements
for the sale of goods subject to legal metrology control.
SANS 347, Categorization and conformity assessment criteria for all pressure equipment.
SANS 1091, National colour standard.
SANS 1274, Coatings applied by the powder-coating process.
SANS 1306-1/ISO 228-1, Pipe threads where pressure-tight joints are not made on the threads – Part 1:
Dimensions, tolerances and designation.
SANS 1518, Transport of dangerous goods – Design, construction, testing, approval and maintenance
of road vehicles and portable tanks.
SANS 1700-2-5/ISO 965-1, Fasteners – Part 2: Screw threads – Section 5: ISO general purpose metric
screw threads – Tolerances – Principles and basic data.
screw threads – Tolerances – Limits of sizes for general purpose external and internal screw threads –
Medium quality.
screw threads – Tolerances – Deviations for constructional screw threads.
SANS 1825, Gas container test stations – General requirements for periodic inspection and testing of
portable and transportable refillable gas containers.
SANS 10006, Colour marking and identification of medical gas cylinders and anaesthetic apparatus.
SANS 10019:2011
Edition 7
SANS 10087-1, The handling, storage, distribution and maintenance of liquefied petroleum gas in
domestic, commercial, and industrial installations – Part 1: Liquefied petroleum gas installations
involving gas storage containers of individual water capacity not exceeding 500 L and a combined water
capacity not exceeding 3 000 L per installation.
domestic, commercial, and industrial installations – Part 3: Liquefied petroleum gas installations
involving storage vessels of individual water capacity exceeding 500 L.
domestic, commercial, and industrial installations – Part 4: The transportation of LP gas including the
design, construction, inspection, fittings, filling, maintenance and repair of LP gas bulk vehicles and rail
tank cars.
domestic, commercial, and industrial installations – Part 6: The application of liquefied petroleum and
compressed natural gases as engine fuels for internal combustion engines.
domestic, commercial, and industrial installations – Part 7: Storage and filling premises for refillable
liquefied petroleum gas (LPG) containers of gas capacity not exceeding 9 kg and the storage of
individual gas containers not exceeding 48 kg.
SANS 10087-8, The handling, storage, and distribution of liquefied petroleum gas in domestic,
commercial, and industrial installations – Part 8: The fuelling of fork lift trucks and other LP gas operated
vehicles.
SANS 10228, The identification and classification of dangerous goods for transport.
SANS 10229-1, Transport of dangerous goods – Packaging and large packaging for road and rail
transport – Part 1: Packaging.
SANS 10231, Transport of dangerous goods – Operational requirements for road vehicles.
SANS 10234, Globally Harmonized System of classification and labelling of chemicals (GHS).
SANS 10263-0, The warehousing of dangerous goods – Part 0: General requirements.
SANS 10263-2, The warehousing of dangerous goods – Part 2: The storage and handling of gas
cylinders.
SANS 10297, The reconditioning of external LPG cylinder valves.
SANS 10400 (SABS 0400), The application of the National Building Regulations.
SANS 10461, Gas cylinders – Seamless aluminium-alloy gas cylinders – Periodic inspection and testing.
SANS 11120/ISO 11120, Gas cylinders − Refillable seamless steel tubes of water capacity between
150 L and 3 000 L – Design, construction and testing.
SANS 17020/ISO/IEC 17020, General criteria for the operation of various types of bodies performing
inspection.
SANS 50144-1/EN 144-1, Respiratory protective devices – Gas cylinder valves – Part 1: Thread
connections for insert connector.
SANS 10019:2011
Edition 7
SANS 50250/EN 250, Respiratory equipment – Open-circuit self-contained compressed air diving
apparatus – Requirements, testing, marking.
3 Definitions
For the purposes of this document, the definitions given in the relevant manufacturing standards, in
SANS 162, and the following apply.
3.1
acceptable
acceptable to the authority administering this standard, or to the parties concluding the purchase
contract, as relevant
3.2
accreditation authority
South African National Accreditation System (SANAS) established by the relevant national legislation
(see foreword)
3.3
approved
approved by the approving authority
3.4
approved inspection authority
inspection authority approved or recognized by the approving authority
3.5
approved test station
test station holding accreditation in terms of the requirements of SANS 1825 and SANS 17020
3.6
approving authority
appropriate of the following:
a) within the scope of the the relevant national legislation (see foreword): the Chief Inspector;
b) within the scope of the the relevant national legislation (see foreword): the Chief Inspector; and
c) within the scope of SANS 10400: the local authority concerned
3.7
bundle
see pressure receptacle
3.8
certification
verification that a pressure receptacle complies with the relevant manufacturing standards
3.9
charging pressure
pressure stamped on a pressure receptacle for a permanent gas to indicate the maximum gauge
pressure (measured or corrected to 20 °C) that may be applied at the time of filling
3.10
class of pressure receptacle
category into which pressure receptacle is placed based on whether the pressure receptacle is
seamless, or of welded construction with the weld being fully or partially radiographed
SANS 10019:2011
Edition 7
3.11
compatibility
acceptable interaction of gas and cylinder or gas and cylinder equipment under conditions of use
competent person
person that has the knowledge, training and experience specific to the work or task being performed
3.13
compressed gas
gas which when packed under pressure for transport is entirely gaseous at −50 °C
NOTE This category includes all gases with a critical temperature less than or equal to −50 °C.
3.14
cylinder
3.15
developed pressure
pressure achieved by the contents of a pressure receptacle, filled in accordance with this standard,
when raised to the reference temperature
3.16
dissolved gas
gas which, when packed under pressure for transport, is dissolved in a liquid phase solvent
3.17
filling ratio
ratio of the mass of gas to the mass of water at 20 °C that would fill completely a pressure receptacle
fitted ready for use
3.18
high-pressure liquefiable gas
gas which when packaged under pressure for transport is partially liquid at temperatures above −50 °C
and has a critical temperature between −50 °C and +65 °C
NOTE All pressures are given in kPa gauge unless otherwise stated (100 kPa = 105 N/m2 = 1 bar).
3.19
liquefied petroleum gas
LPG
commercial butane, commercial propane, or a mixture of light hydrocarbons (predominantly propane,
propene, butane and butene) that is gaseous under conditions of ambient temperature and pressure,
and that is liquefied by an increase of pressure or a lowering of temperature
3.20
low-pressure liquefiable gas
gas which when packaged under pressure for transport is partially liquid at temperatures above −50 °C
and has a critical temperature above +65 °C
SANS 10019:2011
Edition 7
3.21
maintenance
action that includes one or more of the following activities:
a) routine inspection of gas pressure receptacles;
b) testing and repair of pressure receptacles in accordance with SANS 1825;
c) changing of valves; or
d) restoring the external appearance of the pressure receptacle, including labelling and painting
3.22
maximum permissible operating pressure
highest pressure permitted to be developed during service
3.23
normalize
heat treatment
heat a cylinder to a uniform temperature above the upper critical point (AC3) of the steel to regenerate or
homogenize the metallurgical structure of the steel to a sufficient degree to achieve the desired
properties, and then cool it in a controlled or still-air atmosphere
3.24
non-refillable cylinder
cylinder which is designed to be filled only once after original manufacture
3.25
pressure receptacle
collective term that includes cylinders, bundles, tubes and pressure drums for the storage and
transportation of liquefied or compressed gases having a water capacity from 0,5 L to 3 000 L
NOTE 1 All types of pressure receptacles excluding non-refillable cylinders are refillable.
NOTE 2 The terms "transportable gas containers", "transportable pressure containers" and "containers" as used in
SANS 347, the relevant national legislation (see foreword), EIGA documents and the various manufacturing
standards listed in annex A are deemed to have the same meaning as a pressure receptacle as defined in this
standard.
3.25.1
bundle
assemblies of cylinders that are fastened together and which are interconnected by a manifold and
transported as a unit
3.25.2
cylinder
transportable pressure receptacles of a water capacity (that may be seamless, welded or composite) of
water capacity 0,5 L to 150 L
3.25.3
tube
seamless transportable pressure receptacles of a water capacity exceeding 150 L and of not more than
3 000 L
SANS 10019:2011
Edition 7
3.25.4
pressure drum
welded transportable pressure receptacles of a water capacity exceeding 150 L and of not more than
1 000 L (e.g. cylindrical pressure receptacles equipped with rolling rings, spheres on skids and dumpy
tanks incorporating skids)
3.26
pressure drum
3.27
pressure relief device
device that is fitted to the cylinder or cylinder valve and is designed to relieve gas pressure in the event
of abnormal conditions resulting in the development of excess pressure inside the cylinder
3.28
re-certification
certification of previously certified equipment where the required traceability (to the applicable statutory
regulations and supporting documentation) is no longer available
3.29
revalidation
periodic inspection and testing of transportable pressure receptacles to an approved standard
3.30
SANAS
South African National Accreditation System established by section 3 of the relevant national legislation
(see foreword)
3.31
special gas
gas or gas mixture that has specific properties and is prepared for special applications (e.g. instrument
calibration gas mixtures or technical diving mixtures)
3.32
tare mass
mass of the cylinder and other fittings not removed during the filling operation, such as the valve, dip
tube and any permanent or semi-permanently fixed valve protection device(s)
3.33
temperature
3.33.1
critical temperature
temperature above which the gas cannot exist in a liquid state
3.33.2
reference temperature
maximum temperature that the gas in the gas pressure receptacle can be expected to reach under
normal service conditions (see tables 1 to 6)
3.34
test pressure
pressure to which a pressure receptacle is subjected in accordance with its design standard
SANS 10019:2011
Edition 7
3.35
tube
see pressure receptacles
3.36
verification
act of reviewing, inspecting, testing, checking, auditing or otherwise determining and documenting
whether items, processes, services or documents comply with specified requirements
3.37
working pressure
settled pressure of a compressed gas at a uniform reference temperature of 20 °C in a full pressure
receptacle
NOTE In North America, service pressure is often used to indicate a similar condition, usually at 21,1 °C.
4 Design and manufacturing requirements

4.1 General
Pressure receptacles shall be designed and manufactured in accordance with the requirements of the
relevant national legislation (see foreword) in conjunction with the appropriate of the standards listed in
(a) to (t) (see also annex A) and SANS 347.
NOTE Specific additional requirements or limitations (or both) in respect of a standard listed below are indicated in
brackets.
a) Refillable welded stainless steel cylinders: SANS 399.
b) Refillable seamless steel gas cylinders of water capacity up to 150 L: SANS 9809-1, SANS 9809-2
and SANS 9809-3.
c) Refillable seamless steel tube containers of water capacity from 150 L to 3 000 L: SANS 11120.
d) Dissolved acetylene cylinders of water capacity up to 150 L: ISO 3807-1 or ISO 3807-2.
e) Refillable welded steel gas containers of water capacity up to 500 L: SANS 4706. (Welded steel
cylinders manufactured for LPG shall use a test pressure of 3 000 kPa and a ratio of 0,425 for
cylinder design.)
f) Steel containers of 150 L up to 1 000 L water capacity with welded seams: EN 14208.
g) Seamless aluminium gas cylinders of water capacity up to and including 150 L: SANS 7866.
h) Fully wrapped composite cylinders up to 450 L: EN 12245. (These containers shall have a lining as
described in EN 12245 when manufactured for use in South Africa.)
i) Hooped wrapped composite cylinders: ISO 11119-1.
j) Fully wrapped fibre-reinforced composite gas cylinders with load sharing metal liners: ISO 11119-2.
k) Fully wrapped fibre-reinforced composite gas cylinders with non-load sharing metal or non-metallic
liners: ISO 11119-3.
10
SANS 10019:2011
Edition 7
l) Low pressure fire extinguishers with a gross mass not exceeding 23 kg: SANS 1151, SANS 1739
and SANS 1910.
NOTE Fire extinguishers using halon as an extinguishing medium should have been phased out by
2010 because of the Montreal Protocol agreement of which South Africa is a signatory.
m) Welded transportable vessels of water capacity 501 L to 3 000 L: SANS 1518.
n) Welded LPG fuel containers for motor vehicles up to 150 L: SANS 20067.
o) Welded CNG fuel containers for motor vehicles up to 150 L: SANS 20110.
p) Welded aluminium alloy gas cylinders up to 150 L: ISO 20703.
q) Brazed steel cylinders for compressed gases up to 20 L: AS 2468. (Cylinders made in accordance
with AS 2468 shall be fitted with a pressure relief device.
NOTE Notwithstanding the requirements of AS 2468, LPG cylinders may only be accepted in the normalized
condition. Whilst AS 2468 refers only to compressed gases, LPG cylinders made in accordance with AS 2468 are
acceptable. Specific gas types are listed in AS 2030, and in the definitions of that standard, LPG is referred to as a
compressed gas.
r) Non refillable metallic gas cylinders: DOT 39.
s) Non refillable metallic gas cylinders: ISO 11118.
t) Non refillable metallic gas cylinders: EN 12205.
The above list of standards does not preclude the design, manufacture and use of pressure receptacles
to any of the current standards listed in annex A or in SANS 1825 and found in the schedule of the
relevant national legislation (see foreword).
4.2 Additional design requirements for pressure receptacles

As a matter of principle the developed pressure of a gas at its reference temperature shall not exceed
the test pressure of the pressure receptacle. However the elevated minimum test pressures stated in
tables 5 and 6 shall apply as they take into account additional safety factors regarding the properties of
the contained gas. In terms of the requirements set out in 4.1, it is the responsibility of the purchaser to
ensure full compliance with these requirements for both new and second-hand pressure receptacles.
Imported new and second hand cylinders may have a stamped charging pressure and product content
related to a lower reference temperature as used in the country of origin. In such cases the 20 ºC
reference temperature in South Africa will correlate to a lower product mass for the same stamped
settled charging pressure. It is the responsibility of the filler to ensure that cylinders filled in South Africa
are filled to a product mass calculated using reference temperature 20 ºC. See also annex F.
For low-pressure liquefiable gases, the maximum filling ratio shall be such that the liquid portion of the
gas does not occupy more than 97 % of the volume of the pressure receptacle at a reference
temperature of 55 °C and the pressure receptacle shall not be liquid full at a temperature of 60 °C.
All LPG pressure receptacles, including butane and propane pressure receptacles, shall be rated for a
test pressure of 3 000 kPa and shall be designed to a fill ratio of 0,425.
11
SANS 10019:2011
Edition 7
4.3 Heat treatment

The heat treatment applied to gas pressure receptacles during manufacture and maintenance shall be
applied in accordance with the relevant design specification. All welded steel cylinders manufactured for
liquefied gases, including LPG, shall be supplied to South Africa in a normalized condition between
900 °C and 930 °C.
The powder coating of aluminium cylinders shall be in accordance with SANS 1274 and SANS 10461.
NOTE The process of powder coating can adversely affect the mechanical properties of an aluminium cylinder if
not properly controlled.
4.4 Class of pressure receptacle

Each metallic pressure receptacle shall have a class rating the numerical value of which shall be not
higher than that given in column 3 of table 7, appropriate to the type of gas given in column 2, subject to
the provision that when the filling conditions are such that the developed pressure for the gas at
reference temperature will exceed 7 000 kPa, only a class 1 pressure receptacle shall be used (see
table 1 for reference temperature and tables 2, 3, 4, 5 and 6 for developed pressure).
4.5 Special-purpose pressure receptacles

Pressure receptacles intended as fuel tanks for motorized vehicles shall be specially manufactured for
this purpose and shall comply with the requirements of SANS 20067 or SANS 20110 (or both).
Pressure receptacles that are intended for general duty shall not be used on motorized vehicles,
however, these pressure receptacles may be used as tanks for forklift trucks, provided they are
specifically adapted and marked as such. (See 8.6.3 and SANS 10087-6.)
No person shall manufacture or import dissolved acetylene cylinders for distribution in South Africa
unless he can produce proof that such cylinders comply with the requirements of ISO 3807-1 or
ISO 3807-2, or other approved standards (see annex A).
4.6 Change of pressure receptacle service
4.6.1 A pressure receptacle may, subject to the limitations given in 4.6.2, be transferred to a different
service, provided that it is thoroughly cleaned and has been inspected and, when applicable, tested in
accordance with clause 7, and provided that the relevant markings and colour coding have been
changed in an acceptable manner to comply with the requirements of the new service and of clause 4.
When a pressure receptacle is transferred to a different service, the filler shall ensure that the developed
pressure of the gas at reference temperature does not exceed the maximum working pressure of the
pressure receptacle and that the pressure receptacle is of a class suitable for the gas (see table 7 and
ISO 11621 and ADR P200).
4.6.2 The transfer of a pressure receptacle to a different service shall comply as a minimum with
ISO 11621.
A pressure receptacle that has been used for the storage of any coal produced gas (i.e. methane or
carbon monoxide), shall not be used for any other gas.
4.6.3 A cylinder equipped with a foot ring shall not be used for underwater service.
12
SANS 10019:2011
Edition 7
4.7 Refillable pressure receptacles (new or used)
4.7.1 General
4.7.1.1 Only pressure receptacles that, in respect of basic design and manufacture, comply with the
appropriate and relevant requirements of this standard, together with standards approved by the
Department of Labour (DOL) and, in the case of LPG pressure receptacles up to and including 113 L,
that have been verified by an organization approved by the Chief Inspector, shall be allowed for general
distribution and use in South Africa.
4.7.1.2 Refillable pressure receptacles that are not accompanied by a manufacturer's certificate of
construction and certification by an approved inspection authority, or a certificate of re-certification
issued by an approved inspection authority shall not be allowed for distribution and use in South Africa.
4.7.1.3 Used imported refillable pressure receptacles that do not comply with 4.7.1.1 and 4.7.1.2 may
be distributed and used in South Africa provided that they are certified by an approved inspection
authority, retested, declared and certified as safe for use by a government-accredited test station to an
approved standard.
For approved standards, see annex A or SANS 1825.
4.7.1.4 New pressure receptacles shall not be manufactured to any local, regional or international
standard that has been withdrawn. Evaluation of non-listed manufacturing standards will be the
responsibility of an evaluation committee (see 4.7.2 and 4.8.3).
NOTE For a list of Approved Inspection Authorities contact the Government Department of Labour.
4.7.1.5 LPG cylinders, LPG cylinder valves and individual relief valves fitted to cylinders shall be verified
by an organization approved by the Chief Inspector prior to importation or local manufacture.
4.7.2 Approval of non-listed standards
For the purpose of approval of non-listed design and manufacturing standards other than those referred
to in 4.7.1, the standards shall first be evaluated by an evaluation committee (see 4.8) before the
importation or manufacture of pressure receptacles to such standards.
4.8 Evaluation committee
4.8.1 General
The evaluation committee shall, after evaluation of the non-listed standard, make a recommendation to
the relevant approving authority for incorporation with or without amendments of the standard into
relevant government legislation. (See also annexes A and A.1.)
4.8.2 Composition of evaluation committee
The Department of Labour shall establish an evaluation committee, which shall consist of
representatives from the following organizations:
a) Department of Labour (DOL): one member;
b) South African Compressed Gases Association (SACGA): two members;
13
SANS 10019:2011
Edition 7
c) Liquefied Petroleum Gas Safety Association of Southern Africa (LPGSASA): two members;
d) SABS Standards Division: one member;
e) Approved Inspection Authorities (AIA): one member;
f) Divers Alert Network of SA: one member;
g) Department of Minerals: one member;
h) Department of Energy: one member;
i) Federation of Trade Unions in South Africa (FEDUSA): one member;
j) SAQCC Fire: one member; and
k) two co-opted specialist members, as required.
NOTE It is the responsibility of the DOL PER committee to appoint the chairperson of this committee.
4.8.3 Duties and responsibilities of the evaluation committee
The duties and responsibilities of the evaluation committee shall include the relevant of the following:
a) evaluating of non-listed standards;
b) recording the names and numbers of approved manufacturing specifications for future control and
verification (as listed in annex A);
c) arbitrating in disputes or complaints;
d) investigating cases of procedural failure;
e) giving advice on any query related to all the above;
f) making recommendations to the appropriate approving authority on any matters relating to its
functions; and
g) operating within the committee’s "terms of reference" which includes the requirement to meet at least
once a year.
5 Valves
5.1 General
The design and construction of valves shall be such as to render the valves acceptable for the duty and
service for which they are intended. All parts of valves in contact with the contents of the pressure
receptacles shall be of material that will not react with the gas or the metal of the pressure receptacle.
All LPG cylinder valves shall comply with the requirements of SANS 199 or ISO 15995 provided that the
valve inlet and outlet connections requirements shall comply with the requirements given in 5.3.
LPG cylinder valves that do not incorporate a pressure relief device may not be fitted to cylinders unless
a separate pressure relief device is fitted directly into the cylinder.
With the exception of special gases, when the regulator is connected to the outlet of a refillable
14
SANS 10019:2011
Edition 7
container, it shall be done so without the use of any outlet thread adapter changing one thread size to
another thread size including left to right and right to left conversions.
5.2 Valve outlet connections

All new gas cylinder valve outlet connections shall comply with the requirements of table 8. See table 9
for refrigerants and table 10 for valve outlets on SCUBA cylinders.
NOTE Refer to annex B for a list of acceptable standards pertaining to valves used on pressure receptacles.
If the pressure receptacles are required to be refilled then this standard shall be complied with. Imported
pressures receptacles containing special gases with a non-compliant valve outlet can be used but not
refilled. Should these remain in South Africa after first usage the valve shall be changed to comply with
the requirements of this standard.
Valve outlets for special gas mixtures are defined by the individual gas company in accordance with the
standards in this standard.
5.3 LPG cylinder inlet and outlet requirements

Valves with an SANS 1306-1 G ⅜ RH outlet thread shall not be fitted to cylinders of water capacity
exceeding 20 L. Valves with an SANS 1306-1 G ⅝ LH outlet shall not be fitted to cylinders with a water
capacity less than 20 L. Outlet connections for butane, LPG and propane shall be as specified in
SANS 199.
Valves with a ¾ NGT inlet shall not be fitted to cylinders with a water capacity less than or equal to 20 L.
Valves with a ½ NGT inlet shall not be fitted to cylinders with a water capacity exceeding 20 L.
For composite cylinders see the requirements as given in SANS 199.
5.4 Valve stem and pressure receptacle neck thread connections

The valve stem is the section of the valve body that connects to the pressure receptacle body, and as
such shall have matching threads for compatibility (see table 11).
For cylinders less than 10 L, the preferred valve thread connections are 17E or 18T. However, based
upon an agreement between the owner/purchaser and the manufacturer 25E threads are acceptable.
NOTE This is not applicable to LPG cylinders.
5.5 Protection of valves

5.5.1 General
Unless as provided for in 5.5.2, valves on pressure receptacles shall be protected against mechanical
damage.
On any cylinder containing a gas that is flammable or toxic (or both), the valve shall be protected by
means of a detachable cap that can be securely attached to the pressure receptacle. However, the cap
shall not be required if the valve is set into a recess of the pressure receptacle, or is protected by a
shroud or guard made to an approved standard (see ISO 11117), is attached to the cylinder collar or, in
the case of a shroud, is welded to the dome of the cylinder.
15
SANS 10019:2011
Edition 7
Such shroud, guard or cap shall in no way be in contact with any part of the valve.
For pressure receptacles used in the fixed fire protection industry, the valve shall be protected by a cap,
where applicable, when transported or in storage. Pressure receptacles used in trolley units are exempt
from using caps or guards. However, when removed from the trolley unit, the cap or guard shall be fitted.
Pressure receptacles fitted with shrouds may be used in trolley units.
5.5.2 Exceptions
Caps and shrouds are not required on cylinders for SCUBA and SCBA, up to and including 20 L water
capacity.
All fire extinguishers up to and including 15 L water capacity are exempt from using caps or shrouds.
Notwithstanding the requirements of 5.5.1, pressure receptacles of water capacity 10 L and below do not
require a cap, valve guard or shroud. This exception excludes flammable and toxic pressure
receptacles, which shall comply with 5.5.1.
Medical gas cylinders, where the shroud or guard is an integral part of the cylinder or valve package, are
excluded from the requirement of 5.5.1.
If it is not intended for the valve to be protected by a cap or other form of guarding, an impact test shall
be carried out on the valve, in accordance with ISO 10297.
5.6 Fitting of valves to pressure receptacles

Where the fitting requirements and torque values for valves have not been specified, the requirements of
ISO 13341 shall be complied with. For torque values to be applied to LPG valves, see SANS 199. (See
EIGA Document 138/08/E for thread tape and lead cap material compatibility).
5.7 Inspection and maintenance of valves

As a minimum, valves shall be inspected as per ISO 22434 and shall be inspected at frequency as
shown in annex C. LPG valves shall be inspected as per SANS 10297.
Valves shall be inspected and leak tested at the time of filling. (For LPG See SANS 10087-7). LPG
valves fitted with a relief valve shall be maintained at least every 10 years in accordance with the
requirements of SANS 10297 or replaced.
5.8 Valve lubricants

No valve lubricant other than that specified by the original valve manufacturer for the specified gas used
shall be applied to threads or spindles.
6 Pressure relief devices

6.1 General
The purpose of pressure relief devices is to relieve pressure in a pressure receptacle when the pressure
receptacle is exposed to adverse conditions. The device shall be of robust construction and shall be
capable of an accurate setting. All parts of the device shall be of material(s) that will not react with the
contents or the metal of the pressure receptacle on which it is mounted. Pressure relief devices shall be
prohibited for toxic and poisonous gases. For these exclusions, see ADR P200. (See also BS 341-4 for
further guidance regarding the design and application of pressure relief devices).
16
SANS 10019:2011
Edition 7
Cylinders incorporating a pressure relief valve or bursting disc shall have these safety components
replaced within 10 years of the date of the original manufacture and every 10 years thereafter. (See
tables 5 and 6).
6.2 Type of pressure relief devices
6.2.1 General
More than one type of pressure relief devices may be used and more than one device of the same type
may, when so required, be used on one pressure receptacle.
6.2.2 Spring-loaded pressure relief devices
A spring-loaded pressure relief device shall be set (when installed on a pressure receptacle) to
commence relieving between 75 % and 100 % of the minimum test pressure of the pressure receptacle
and be adequately sized in terms of its discharge capacity. For the performance requirements of spring
loaded safety valves on LPG cylinders whether fitted directly into the cylinder or incorporated in the
cylinder valve refer to SANS 199.
6.2.3 Frangible discs
6.2.3.1 Primary frangible discs
Primary frangible discs shall be designed to rupture at the reference temperature of the maximum
permissible operating pressure of the pressure receptacle. (Refer to table 1).
6.2.3.2 Secondary frangible discs
Secondary frangible discs shall rupture at a nominal pressure that is 10 % above the start-to-discharge
pressure of the pressure relief device.
6.2.4 Fusible plugs
A fusible plug shall contain a fusible alloy that has a yield temperature of not lower than 96 °C and not
higher than 110 °C. At ambient temperature the fusible plug shall withstand pressure equal to the
applicable hydrostatic test pressure.
6.3 Location of safety devices

With the exception of CO2 fire suppression systems where a pressure relief device is fitted to a cylinder
containing a liquefied gas, it shall be so positioned that when the cylinder is in the upright position, gas
or vapour will be vented in preference to liquid.
For the incorporation of pressure relief devices into cylinders see ADR P200. (See also table 5 and 6.)
A pressure relief device on a transportable pressure receptacle shall be protected against mechanical
damage either by the way in which it is set into the transportable pressure receptacle, or by being
protected with an acceptable housing.
NOTE For more information regarding the use of pressure relief valves see EIGA Document IGC/91/03/E available
on the EIGA website (www.eiga.org).
17
SANS 10019:2011
Edition 7
7 Revalidation of pressure receptacles

7.1 General
Only an approved test station shall carry out periodic inspection and testing (revalidation). The frequency
of inspection and hydrostatic testing shall be in accordance with the requirements of SANS 1825.
NOTE For ease of reference, the frequency of inspections and testing is given in annex C.
7.2 Test stations
7.2.1 Approval
All test stations shall be approved by an approving authority.
7.2.2 Accreditation
Before approval, the test station shall be accredited by a government-endorsed national accreditation
body to an agreed scope between the test station and SANAS (see SANS 17020 and SANS 1825).
7.3 Safety precaution

Cylinders that are overdue for inspection and testing shall not be refilled.
7.4 Rejection and rendering pressure receptacles unserviceable

When pressure receptacles are to be rejected (scrapped), this function shall be carried out by a
competent person. The decision to reject a pressure receptacle may be taken at any stage during the
inspection and testing procedure.
If it is impossible to recover a rejected pressure receptacle, it shall, after notifying the owner, be made
unserviceable by the testing station for holding gas under pressure so that it is impossible for any part of
the cylinder, especially the shoulder, to be re-issued into service. In case of any disagreement, the test
station and owner shall understand the legal implication of the contemplated action. Rejection and
disposal criteria for pressure receptacles and methods for rendering pressure receptacles unserviceable
shall be as given in SANS 1825. For the rejection criteria of LPG pressure receptacles, the rejection
criteria given in the relevant tables in SANS 1825 shall apply.
Should the owner scrap or reject his own pressure receptacles, the rejection criteria shall be as provided
in SANS 1825, and an approved test station shall dispose of the pressure receptacle in the appropriate
manner.
7.5 Repair of welded steel pressure receptacles

All repairs that require the application of heat to the body or any component part of the body shall be
carried out under the direction and supervision of an approved inspection authority. The pressure
receptacle shall be hydrostatically tested and verified by an approved test station before being placed
back into service (see also 8.1 and 8.3).
Under no circumstances shall seamless pressure receptacles of any size be repaired.
18
SANS 10019:2011
Edition 7
8 Marking, labelling, colour coding and certificates

8.1 Permanent marking
Each pressure receptacle shall be legibly and durably marked (hard-stamped, embossed or embedded
in the resin of composite pressure receptacles) with the information required by the applicable design
standard or ISO 13769.
Pressure receptacles for compressed gases are not required to be marked with the tare mass, in
accordance with the requirements of ISO 13769. When cylinders without tare mass are changed from a
permanent gas service to a liquefiable gas service, the tare mass shall be stamped onto the shoulder of
the pressure receptacle, provided the pressure receptacle complies with the design requirements for that
particular gas, which shall be verified by a competent person. The tare shall be given in kilograms (kg).
Liquefiable pressure receptacle stampings shall comply with the requirements of an approved
manufacturing standard and, in addition, shall give the type of gas content (for example, "NH3" for
ammonia, or "butane" or "propane" or "LPG"). The markings for the tare and test pressure shall be in
kilograms (kg) and kilopascals (kPa), respectively. The letter "N" shall be stamped on liquefied gas
pressure receptacles (including LPG) to indicate that the pressure receptacle has been normalized.
For gases other than LPG, where the cylinder stamp marking standards allow, the unit of pressure on
any pressure receptacle or associated valve governed by this standard, the unit of pressure 'bar' can be
used as an alternative to 'Pa' (Pascal) and multiples thereof.
No permanent marking shall be removed from any pressure receptacle, however, where change of
ownership takes place, the previous owner’s marks may be cancelled by over-stamping using a
letter "X".
The manufacturer’s serial number shall never be removed from any pressure receptacle.
For re-rating of cylinders in respect of test pressure the cylinder design shall be approved by an AIA and
the inspection and test shall be validated by the government approved test facility.
8.2 Identification of permanent marking

The manufacturer shall, on the certificate of manufacture (see 8.7.2) or on the certificate of re-
certification, list all the permanent markings on the pressure receptacle.
8.3 Permanent marking following revalidation
8.3.1 Notwithstanding the exceptions in 8.3.2 and 8.3.3, the following additional permanent markings
shall be hard-stamped on the shoulder of the pressure receptacle after revalidation:
a) the approved test station identification mark;
b) the year and month (for example 11/04 (yy/mm)) and the suffix "H" if a hydrostatic test has been
done; and
c) when relevant, the new tare mass.
8.3.2 In addition to the requirements of 8.3.1, after internal inspection of acetylene cylinders, the year
and month in which the inspection was carried out, followed by an "I" (for example 11/04 I (yy/mm)),
shall be hard-stamped on the pressure receptacle, or on a metal test ring retained between the valve
inlet stem and cylinder shoulder.
19
SANS 10019:2011
Edition 7
8.3.3 Hard-stamping shall only be done on the foot ring, shroud or doubling plate specifically attached
for the purpose of cylinder identification of a revalidated welded pressure receptacle.
8.4 Maintenance of permanent marking

Permanent markings on a pressure receptacle shall be maintained in an acceptable manner and the
pressure receptacle shall not be filled if the markings are illegible. Cylinders protected by an outer sleeve
(e.g. plastic coating) may be filled if fitted with a test date ring and it is within the test date period.
8.5 Colour coding
8.5.1 Colour identification of cylinders
The colours in table 12 are the allocated colours for the gases indicated in column 2. When changing the
service of a pressure receptacle, the old paint shall be removed entirely before the application of the
new identification colour.
Where colours are allocated to fire extinguishers, these shall comply with the requirements of
SANS 1910 and SANS 1567.
8.5.2 Pressure receptacles for other commonly used gases (other than LPG)
8.5.2.1 Cylinders
Cylinders for the gases listed in table 11 shall have the body colour as given in the table.
In addition, cylinders shall indicate the nature of their contents by means of colour bands. The width of
the second band, where applicable, shall be at least one-quarter of the diameter of the cylinder and be
adjacent to the shoulder of the cylinder.
If the gas is toxic and non-flammable, the cylinder shall have a golden yellow (1070-Y20R) shoulder
band.
If the gas is non-toxic and flammable, the cylinder shall have a signal red (1580-Y90R) shoulder band.
If the gas is toxic and flammable, the cylinder shall have a golden yellow (1070-Y20R) shoulder band as
well as a signal red (1580-Y20R) shoulder band. The red band shall be next to the neck and the yellow
band shall be between the red band and the junction of the shoulder and body of the cylinder.
Imported cylinders not for trade use can remain in the "as supplied" colour, however notwithstanding the
aforementioned, such cylinders shall be appropriately labelled in accordance with 8.6. Should these
cylinders remain in South Africa after first usage the colour shall be changed to comply with this
standard.
8.5.2.2 Pressure receptacles other than cylinders
The colour coding used shall be as given in table 12. In addition to the permanent marking requirements,
the outer surface of these pressure receptacles shall be so painted as to have the appropriate colour
marking given in 8.5.3 to 8.5.7 (inclusive). The width of each shoulder band shall be at least one-quarter
of the diameter of the pressure receptacle body.
8.5.3 LPG cylinders
Corporate colours used on LPG cylinders shall be registered with the Liquefied Petroleum Gas Safety
Association of Southern Africa. White, grey and aluminium are acceptable colours for LPG without being
20
SANS 10019:2011
Edition 7
registered. Where colours are registered, there shall be no confusion with colours allocated for other
gases or applications.
8.5.4 Pressure receptacles for gases for which specific colour markings have not been
allocated
Unique identification colours for branded pressure receptacles for compressed and liquefiable gases
(excluding LPG pressure receptacles) shall be approved and registered by the South African
Compressed Gases Association (SACGA) to avoid any colour duplication with table 12.
The valve guard for pressure receptacles for refrigerant gases shall be coloured in accordance with
ASHRAE 34 and table 13. If corporate branding is required, it shall be approved and registered with the
South African Fluorocarbon Association (SAFA) to avoid any colour duplication with table 13.
Before registration, the association concerned (SACGA or SAFA) shall apply to the approving authority
for approval.
Pressure receptacles for special gases or pressure receptacles for which specific colour markings have
not been allocated shall be coloured Protea (1020-Y80R), or as otherwise approved.
8.5.5 Cylinders for medical gases
Cylinders for medical gases shall be colour-marked in accordance with SANS 10006.
8.5.6 Cylinders for SCUBA and SCBA use
Cylinders for SCUBA and SCBA use shall be colour-marked with the appropriate colour given in
annex D. Marking shall be in accordance with SANS 50250. The body of a cylinder used for diving and
surface rescue purposes shall be Golden yellow and the shoulder shall be French grey (see annex D).
8.5.7 Pressure receptacles fitted with internal tubes for liquid withdrawal
A pressure receptacle fitted with a conventional-type vapour withdrawal valve that is connected to an
internal eductor tube or dip tube for liquid withdrawal shall be clearly marked by means of two
diametrically opposed vertical yellow (in the case of chlorine cylinders, black) stripes of width 50 mm, to
indicate the presence of the eductor or dip tube. In the case of a pressure receptacle fitted with a dual-
purpose valve that has both vapour and liquid outlets, the liquid withdrawal outlet shall be clearly
identified and the liquid and vapour outlets shall be non-interchangeable. This does not apply to
refrigerant recovery cylinders. Fire extinguishers and fire suppression systems are exempt from this
requirement.
8.6 Labelling
8.6.1 Precautionary labels
8.6.1.1 General
The labelling of cylinders (excluding LPG) shall comply with ISO 7225.
8.6.1.2 Breathing gas
Components of breathing gas mixtures other than air shall be listed on a 100 mm wide self-adhesive
band fixed adjacent to the shoulder (see annex D).
21
SANS 10019:2011
Edition 7
8.6.2 Dangerous-commodity labels
If a pressure receptacle has been filled with a dangerous commodity as defined in SANS 10228, and is
to be conveyed by any type of transport on a public road, it shall be labelled in accordance with
SANS 10229-1, except that, when the form of the pressure receptacle is readily visible, the pressure
receptacle need not bear the "compressed gas" label. If a pressure receptacle is concealed in an outer
box or some other type of container, the outer container shall bear the "compressed gas" label and the
label applicable to the commodity in the pressure receptacle and shall, in general, comply with the
requirements of SANS 10234 and SANS 10263-0.
8.6.3 Labelling on LPG pressure receptacles
LPG cylinders of water capacity not exceeding 20 L shall bear, in the form of a pictogram (see figure E.1
in annex E) on an adhesive label (of minimum size 100 mm × 40 mm), a warning that the cylinder shall
not be placed on hot plates or stoves, or be exposed to excessive heat, and shall always be used in an
upright position.
All cylinders shall indicate the direction of use and transportation. (See figure E.2 in annex E.)
Cylinders used as forklift truck fuel tanks shall be labelled to identify them for use and direction of
installation. Operating instructions shall be attached and the label shall indicate that the cylinder is for
forklift trucks only and used in liquid service.
8.6.4 Other labelling
In addition to the marking required in terms of 8.1, 8.3 and, when relevant, 8.4, each filled pressure
receptacle shall be labelled in accordance with the relevant national legislation (see foreword) and
SANS 289.
8.7 Certificates
8.7.1 General
Manufacturers (as defined in the relevant national legislation (see foreword)) shall keep and make
available on request manufacturing and inspection certificates for pressure receptacles sold. Batch
certificates are acceptable.
8.7.2 Certificates of manufacture
The requirements for certificates of manufacture shall be as specified in the appropriate manufacturing
standards.
8.7.3 Revalidation inspection and test certificates
Revalidation inspection and test certificates shall comply with the requirements given in SANS 1825.
Cylinders in service shall be inspected and tested in accordance with frequencies given annex C.
22
SANS 10019:2011
Edition 7
9 Filling of pressure receptacles

9.1 General
Before filling an inspection shall be performed as specified in this clause. Should the cylinder fail based
on the rejection criteria the owner shall ensure the disposal of the cylinder is carried out as per
SANS 1825 or shall be sent to an approved test station for further examination or disposal.
The rejection criteria are in accordance with SANS 1825, based on ISO standards.
9.1.1 Permission to fill pressure receptacles
Permission to fill shall be obtained from the owner of the pressure receptacle in writing, except where
the pressure receptacle is privately owned by the end user. This requirement is for safety reasons. The
pressure receptacle containment history is an essential requirement for safe filling.
9.1.2 Persons competent to fill pressure receptacles
No person shall fill a pressure receptacle with gas unless the person is competent to fill pressure
receptacles with the gases being handled, and is conversant with the relevant requirements of this
standard.
9.1.3 Inspection before, during and after filling
The pre-fill inspection of the pressure receptacle by the filler shall be in accordance with the criteria
given in table 14 or table 15. Before filling any pressure receptacle, the filler shall ensure that
a) the requirements of 9.1.1 have been satisfied;
b) the pressure receptacle is clean and free from obvious contaminants;
c) the pressure receptacle complies with the requirements of an approved standard and has the
appropriate pressure rating;
d) the pressure receptacle is not due for periodic inspection or testing;
e) the pressure receptacle, valve and pressure relief devices, if any, are in good serviceable condition;
f) the correct cylinder colour has been applied prior to filling for the intended gas service;
g) during filling leak detection shall be carried out with an acceptable leak detection fluid at regular
intervals during filling. Typical checks shall comprise checking of the valve outlet, gland nut and valve
stem to the cylinder neck thread joint; and
h) after filling the pressure receptacle shall be tested for leaks. If a leak is found and it cannot be
stopped by the tightening of spindles or gland nuts, the pressure receptacle shall be emptied and
shall not be refilled until the cause of the leak has been rectified.
When filling a pressure receptacle for sale, the requirements of the relevant national legislation (see
foreword) shall be complied with.
23
SANS 10019:2011
Edition 7
9.2 Filling of pressure receptacle with liquefiable gases

All pressure receptacles filled with a liquefiable gas shall be filled using a Trade Metrology compliant
mass measuring system. If the liquefiable gas to be filled is not shown in tables 5 and 6 then ADR P200
shall apply.
A pressure receptacle filled with a liquefiable gas shall not be filled to its full water capacity. An ullage
space shall be left to allow the gas to expand due to ambient temperature fluctuations up to the
reference temperature without damage to the pressure receptacle in accordance with the allowable
filling ratio. See tables 5 and 6 and ADR P200.
In addition to carrying out the inspection required in terms of 9.1.2, the filler shall ascertain the working
pressure/test pressure, the tare mass and the water capacity of the pressure receptacle and, by
reference to tables 5 and 6 and ADR P200, shall calculate the maximum permissible mass of gas that
can be filled into the pressure receptacle.
9.3 Filling of LPG pressure receptacles

The filling of LPG pressure receptacles shall be carried out in accordance with SANS 10087-3,
SANS 10087-7 and SANS 10087-8.
9.4 Filling of pressure receptacle with permanent gases

NOTE See annex F and tables 3 and 4 for developed pressure for permanent gases.
9.4.1 Precautions for corrosive gases
In addition to the inspection of the pressure receptacle as required in terms of 9.1.2 the valve
functionality shall be checked and, if necessary, the valve shall be reconditioned or replaced.
9.4.2 Acetylene
Inspection and filling of acetylene cylinders shall be carried out in accordance with the company’s
corporate quality systems. For guidance see also ISO 11372 and ISO 13088.
9.5 Filling SCBA and SCUBA cylinders

9.5.1 SCBA and SCUBA
The conditions as provided in clause 9.1.2 shall apply for the filling applications for both these types of
pressure receptacles.
NOTE SCUBA for professional use is covered under the relevant national legislation (see foreword).
9.5.2 Additional checks before filling
In addition to carrying out an inspection in terms of 9.1.2, the filler shall ensure that no cylinder equipped
with a foot ring is used for underwater service, and that the cylinder is not due for periodic inspection or
testing (or both). Where the cylinder has a detachable boot, the filler shall remove the boot and inspect
the bottom of the cylinder for signs of external corrosion.
24
SANS 10019:2011
Edition 7
9.5.3 Cleaning of cylinder before filling
A cylinder shall be oxygen cleaned (see EIGA IGC 33/06 ) before its first fill in NITROX or TRIMIX if the
oxygen concentration is greater than 25 %.
10 Handling, storage, transportation and use

10.1 Handling
Pressure receptacles shall not be subjected to any undue shock. They shall be handled safely and
carefully and sliding, rolling and skidding shall be avoided. See also SANS 10263-2.
10.2 Stacking
10.2.1 General
The maximum height of any stack shall ensure that the cylinders can be handled safely. Only pressure
receptacles that are specifically designed for stacking shall be stacked.
10.2.2 Rules for stacking for liquefied gases
10.2.2.1 All cylinders containing liquid gas shall be stored in a vertical position, resting on their foot
rings or specially formed bases.
10.2.2.2 Only new or refurbished liquefied gas pressure receptacles, containing no liquefied gas, may
be transported and stacked horizontally.
10.2.2.3 Cylinders that are stored vertically may be arranged in groups, each containing up to four rows
of cylinders, with gangways between the groups.
For the stacking of LPG cylinders refer to SANS 10087-4 and SANS 10087-7.
10.2.2.4 New empty cylinders may be stored horizontally. They shall be in single rows or in groups
comprising two rows with the valves adjacent to the gangways. The ends of each horizontal row shall be
securely wedged.
10.2.2.5 Gangways shall be maintained between stacks, walls and fences.
10.2.2.6 When pallets or baskets are used, they shall be placed in single rows with gangways between
the rows.
10.3 Storage
The warehousing of dangerous goods shall be done in accordance with the requirements of
SANS 10228, SANS 10229-1 and SANS 10263-2.
10.4 Transportation
10.4.1 General
10.4.1.1 Transportation shall be carried out in accordance with relevant national legislation (see
foreword), and the requirements of SANS 10228.
25
SANS 10019:2011
Edition 7
10.4.1.2 When gas pressure receptacles are packed, the pack shall comply with the relevant
transportation requirements of the relevant national legislation (see foreword).
10.4.1.3 Pressure receptacles transported in a vehicle shall be so blocked or braced (or both) as to
prevent movement, and shall not project beyond the sides or ends of the vehicle.
10.4.1.4 Cylinders transported in ISO containers for shipping shall conform with local or international
recommendations as per International Maritime Dangerous Goods (IMDG), International Air Transport
Association (IATA) and International Carriage Of Dangerous Goods By Road (ADR).
10.4.1.5 For the transportation of LPG cylinders refer to SANS 10087-4.
10.4.2 Mixed transportation
When pressure receptacles with various types of gases are to be transported together, this shall be
done in accordance with SANS 10231.
10.5 Use of pressure receptacles
10.5.1 When a pressure receptacle is supplied to a user, the applicable safety requirements shall be
supplied as per the relevant national legislation (see foreword).
10.5.2 In view of the possibility of leakage as a result of minor defects, pressure receptacles shall be
stored in vented areas. In the case of gases heavier than air, care shall be taken to ensure that drains or
trenches do not create pockets in which gas might collect. (See SANS 10087-1 and SANS 10087-3.)
If a leaking pressure receptacle is found and the leak cannot be stopped easily and quickly, the pressure
receptacle shall be moved immediately to that part of an open space where it is least dangerous to life
and property, and advice shall be obtained from the owner/filler prior to any action being taken.
10.5.3 Cylinders shall be disposed of in a manner as described in SANS 1825.
11 General safety precautions

11.1 Pressure receptacles exposed to fires
Where it is evident from the condition of the paint that a pressure receptacle has been exposed to fire, it
shall be immediately removed from service or its place of storage, and be presented for inspection and
evaluation to an approved inspection station, which will follow the requirements of SANS 1825.
11.2 Position and support of pressure receptacles in use

Pressure receptacles containing liquefiable gases and pressure receptacles containing dissolved
acetylene shall always be used in the normal upright position for gas or liquid withdrawal and, when
relevant, shall be so supported that they cannot be knocked over. Pressure receptacles that may be
used in a horizontal position shall be so secured that they cannot roll. If portable tanks are on their
transportation cradles, they shall be secured so that they cannot move.
11.3 Reporting of incidents

Incidents as defined in the relevant national legislation (see foreword) shall be reported as per the
defined requirements.
26
SANS 10019:2011
Edition 7
11.4 Handling of pressure receptacle emergencies

Refer to IGC Doc 80/08 for practical guidance.
Table 1 — Reference temperatures
1 2 3 4
Reference temperature for developed pressure
Water capacity of pressure
receptacle °C
Liquefiable gases Permanent
L Low pressure High pressure gases
0,5 up to but not including 150 65 65 65

150 to 1 000 inclusive 65 65 65
Greater than 1 000 up to and
including 3 000 60 60 65
27
SANS 10019:2011
Edition 7
Table 2 — Properties and pressure groups of permanent gasesa
1 2 3 4 5
Critical
Chemical Dangerous Developed
Name of gas b c temperature
symbol properties pressure group
°C
Air – – 2 −140,7
Argon Ar – 2 −122,0
d
Boron trifluoride BF3 T −12,3
Carbon monoxide CO F and T(A) 2 −140,0
Coal gas – F and T 1 –
e
Fluorine F2 C and T −129,0
Helium He – 3 −267,9
Hydrogen H2 F 3 −239,9
Methane CH4 F 1 −82,1
Neon Ne – 3 −228,7
Nitrogen N2 – 2 −147,0
Oxygen O2 – 2 −118,4
a
Gases that have a critical temperature below −10 °C.
b
The properties are indicated as follows:
C = corrosive
F = flammable
T = toxic
T(A) = classified as class A poison
c
The relationship between charging pressures at 20 °C and developed pressures at
65 °C for the three groups of permanent gases, is given in tables 3 and 4,
respectively.
d
When boron trifluoride is filled into a pressure receptacle manufactured in accordance
with this standard, the maximum charging pressure shall not exceed 60 % of the
maximum working pressure of the pressure receptacle.
When boron trifluoride is filled into a pressure receptacle not manufactured in
accordance with this standard and that is designed to be filled with permanent gases
at a pressure of 13 900 kPa at 20 °C (13 650 kPa at 15 °C), the maximum charging
pressure at 20 °C shall be 10 400 kPa.
e
The mass of fluorine filled into any pressure receptacle shall not exceed 5,5 kg. The
pressure at 20 °C shall not exceed 2 800 kPa, and the maximum working pressure of
the pressure receptacle shall not exceed 18 600 kPa.
28
SANS 10019:2011
Edition 7
Table 3 — Permanent gases: charging pressures

and corresponding developed pressuresa
1 2 3 4
Charging pressure Developed pressure at 65 °C
at 20 °C b
kPa (gauge)
kPa Group 1 Group 2 Group 3
2 000 2 300 2 300 2 300
4 000 4 800 4 800 4 600
6 000 7 500 7 200 7 000
8 000 10 200 9 700 9 300
10 000 12 900 12 200 11 600
12 000 15 700 14 700 13 900
14 000 18 600 17 200 16 200
16 000 21 400 19 800 18 600
18 000 24 300 22 300 20 900
20 000 27 200 24 800 23 200
22 000 30 200 27 400 25 500
24 000 33 100 30 000 27 900
26 000 36 100 32 500 30 200
28 000 39 100 35 100 32 500
30 000 42 100 37 600 34 800
a
See annex F for more information on developed pressure for permanent
gases.
b
Values for charging pressures other than those given in column 1 may be
obtained by linear interpolation.
29
SANS 10019:2011
Edition 7
Table 4 — Permanent gases: developed pressures

and corresponding charging pressures
1 2 3 4
Developed Charging pressure at 20 °C
pressure at 65 °C a
kPa
kPa (gauge) Group 1 Group 2 Group 3
2 000 1 800 1 700 1 700
4 000 3 400 3 400 3 400
6 000 4 900 5 000 5 200
8 000 6 400 6 600 6 900
10 000 7 900 8 200 8 600
12 000 9 300 9 800 10 300
14 000 10 800 11 400 12 100
16 000 12 200 13 000 13 800
18 000 13 600 14 600 15 500
20 000 15 000 16 200 17 200
22 000 16 400 17 800 19 000
24 000 17 800 19 300 20 700
26 000 19 100 20 900 22 400
28 000 20 500 22 500 24 100
30 000 21 900 24 000 25 800
32 000 23 200 25 600 27 600
34 000 24 600 27 200 29 300
36 000 25 900 28 700 31 000
38 000 27 300 30 300 32 700
40 000 28 600 31 800 34 500
42 000 29 900 33 400 36 200
a
Values for charging pressures other than those given in columns 2, 3 and
4 may be obtained by linear interpolation.
30
Table 5 — High-pressure liquefiable gasesa
1 2 3 4 5 6 7 8 9
Critical Minimum test Pressure Developed
Chemical Dangerous
Gas name UN number temperature pressure Filling ratio relief pressure at 65 °C
symbol propertiesb
°C kPa gauge device kPa gauge
c d
Acetylene 1001 C2H2 F 35,2 6 000 – – 4 900
25 000 0,76 24 000

Carbon dioxide 1013 CO2 A 30,1 19 000 0,68 Mandatory 18 800
16 500 0,60 16 300
25 000 1,11
19 000 1,04
Chlorotrifluoromethane (R 13) 1022 CCIF3 A 28,8 –d –
12 000 0,90
10 000 0,83
Diborane 1911 B2H6 T, F 16,0 25 000 0,07 Forbidden –
30 000 0,40 d
Ethane 1035 C2H6 F 32,3 – –
12 000 0,30
30 000 0,38 19 600
Ethylene 1962 C2H4 F 9,2 –d
22 500 0,27 14 400
20 000 0,70 d 16 800
Hydrogen chloride 1050 HCI C, T 51,5 –
15 000 0,60 12 600
25 000 0,75 22 600
Nitrous oxide 1070 N2O O 36,4 19 000 0,667 Mandatory 17 000
18 000 0,625 15 300
a
Gases that have a critical temperature below –10 °C.
b
SANS 10019:2011
A = asphyxiant, C = corrosive, F = flammable, O = oxidizing, T = toxic.
c
Acetylene is not a liquefiable gas, but is a gas dissolved under pressure in acetone. Because the porous substance in acetylene cylinders prevents conventional internal
inspections and because the cylinders are subjected to very severe handling in service, the developed pressure of the gas at reference temperature (4 900 kPa at 65 °C) is
considered unacceptable for design purposes, and the minimum wall thickness shall be based on a hydrostatic test pressure, as given in the design standard.
Edition 7
d
The fitting of a pressure relief device to a cylinder valve is subject to the owner’s discretion.
31
Table 5 (concluded)
32
Edition 7
SANS 10019:2011
1 2 3 4 5 6 7 8 9
Critical Minimum test Pressure Developed
Chemical Dangerous
Gas name UN number b temperature pressure Filling ratio relief pressure at 65 °C
symbol properties
°C kPa gauge device kPa gauge
25 000 0,36
Silane 2203 SiH4 F −3,5 Forbidden –
22 500 0,32
30 000 1,10
Silicon tetrafluoride 1859 SiF4 C,T −14,2 Forbidden –
20 000 0,74
16 000 1,38 15 700
d
Sulfur hexafluoride 1080 SF6 A 45,6 14 000 1,34 – 12 300
7 000 1,06
25 000 0,96
Trifluoromethane (R 23) 1984 CHF3 A 26,0 –d –
19 000 0,88
d
Xenon 2036 Xe A 16,3 13 000 1,28
a
b
A = asphyxiant, C = corrosive, F = flammable, O = oxidizing, T = toxic.
c
Acetylene is not a liquefiable gas, but is a gas dissolved under pressure in acetone. Because the porous substance in acetylene cylinders prevents conventional
internal inspections and because the cylinders are subjected to very severe handling in service, the developed pressure of the gas at reference temperature
(4 900 kPa at 65 °C) is considered unacceptable for design purposes, and the minimum wall thickness shall be based on a hydrostatic test pressure, as given in the
design standard.
d
Table 6 — Low-pressure liquefiable gasesa
1 2 3 4 5 6 7 8 9
Critical Minimum test Developed
UN Chemical Dangerous Filling Pressure relief
Gas name b temperature pressure pressure at 65 °C
number symbol properties ratioc device
°C kPa gauge kPa gauge
Ammonia 1005 NH3 C,T 132,4 29 00 0,54 Forbidden 2 848
Boron trichloride 1741 BCl3 C,T 178,8 1 000 1,19 Forbidden 399
d
Bromochlorodifluoromethane (R 12 B1) 1974 CBrCIF2 A 153,7 1 000 1,61 693
d
1,2 – Butadiene 1010 CH2:C:CHCH3 F 176,1 1 000 0,59 –
d
1,3 – Butadiene 1010 CH2:CHCH:CH2 F 152,0 1 000 0,52 –
n-Butane 1011 C4H10 F 152,0 3 000 0,51 Mandatory 620
d
Carbonylsulphide 2204 COS F 105.0 3 000 0.87 2 976
Chlorine 1017 Cl2 C,T 144,0 2 200 1,25 Forbidden 1 886
Chlorine trifluoride 1749 CIF3 C,T,O 153,7 3 000 1,40 Forbidden 614
d
Chlorodifluoromethane (R 22) 1018 CHClF2 A 96,2 2 700 1,03 2 619
d
Chlorotrifluoroethane (R 133a) 1983 CH2ClCF3 A 150,0 1 000 1,18 570
Commercial butane 1011 C4H10 F 150,0 3 000 0,425 Mandatory 980
Commercial propane 1978 C 3 H8 F 95,0 3 000 0,425 Mandatory 2 655
Cyanogen chloride 1589 CClN C,T 215,0 2 000 1,03 Forbidden 462
d
Cyclopropane 1027 C3 H6 F 125,2 1 800 0,55 1 869
d
Dichlorofluoromethane (R 21) 1029 CHCl2F A 178,5 1 000 1,23 494
d
Dichlorotetrafluoroethane (R 114) 1958 C2Cl2F4 A 145,7 1 000 1,30 550
SANS 10019:2011
a
b
A = asphyxiant, C = corrosive, F = flammable, O = oxidizing, T = toxic, T(A) = classified as class A poison
c
For design purposes, LPG cylinders use the ratio 0,425.
Edition 7
d
33
Table 6 (concluded)
34
Edition 7
SANS 10019:2011
1 2 3 4 5 6 7 8 9
Critical Minimum test Developed
UN Chemical Dangerous Filling Pressure relief
Gas name b temperature pressure c pressure at 65 °C
number symbol properties ratio device
°C kPa gauge kPa gauge
d
Dimethylamine 1032 (CH3)2NH F 164,6 1 000 0,59 601
d
Dimethyl ether 1033 C2H6O F 126,9 1 800 0,58 1 517
Ethylamine 1036 C2H7N F 183,4 1 000 0,61 Forbidden 399
Ethylene oxide 1040 C2H4O F, T 195,8 1 500 0,78 Forbidden 483
Hydrogen cyanide 1051 HCN F, T(A) 183,5 10 000 0,55 Forbidden 275
Hydrogen sulfide 1053 H2S F, T 100,0 48 00 0,67 Forbidden 4 714
LPG 1075 – F 95,0 3 000 0,425 Mandatory 2 655
Methylamine 1061 CH3NH2 F 156,9 1 300 0,58 Forbidden 1 081
Methyl bromide (R 40 B 1) 1062 CH3Br T 194,0 1 000 1,51 Forbidden 559
Methyl chloride (R 40) 1063 CH3Cl F 143,0 1 700 0,81 Forbidden 1 463
Nitrosyl chloride 1069 NOCI C, T 167,5 1 300 1,10 Forbidden 1 058
d
Octafluorocyclobutane (RC 318) 1976 C4F8 A 115,3 1 100 1,34 857
Propane 1978 C3H8 F 96,8 3 000 0,43 Mandatory 2 222
d
Propylene 1077 C3H6 F 92,4 2 700 0,43 2 676
Sulfur dioxide 1079 SO2 C, T 157,5 1 200 1,23 Forbidden 1 172
1,1,1,2-Tetrafluoroethane (R 134a) 3159 CF3CH2F A 101,1 1,05 d –
Trimethylamine 1083 C3H9N F 160,2 1 000 0,56 Forbidden 559
Vinyl chloride (R 1140) 1086 C2H3Cl F 156,5 1 200 0,81 Forbidden 1 039
a
b
A = asphyxiant, C = corrosive, F = flammable, O = oxidizing, T = toxic, T(A) = classified as class A poison
c
For design purposes, LPG cylinders use the ratio 0,425.
d
SANS 10019:2011
Edition 7
Table 7 — Class of pressure receptacles for specific gases
1 2 3
Minimum class
Name of gas of pressure
receptacle a
1 Acetylene 3
2 Air 1
3 Ammonia 3
4 Argon 1
5 Boron trichloride 2
6 Boron trifluoride 1
7 Bromochlorodifluoromethane (R 12 B1) 3
8 Bromotrifluoromethane (R 13 B1) 1
9 Butadiene 3
10 Butane, iso- 3
11 n-Butane 3
12 Carbon dioxide 1
13 Carbon monoxide 1
14 Chlorine 2
15 Chlorine trifluoride 2
16 Chlorotrifluoroethane (R 133a) 3
17 Chlorotrifluoromethane (R 13) 2
18 Coal gas 1
19 Cyanogen chloride 2
20 Cyclopropane 3
21 Dichlorodifluoromethane (R 12) 3
22 Dichloromonofluoromethane (R 21) 3
23 Dichlorotetrafluoroethane (R 114) 3
24 Dimethyl ether 3
25 Ethane 1
26 Ethylamine, mono- 3
27 Ethyl chloride 3
28 Ethylene 1
29 Ethylene oxide 3
30 Fluorine 1
31 Helium 1
32 Hydrogen 1
33 Hydrogen chloride 1
34 Hydrogen cyanide 1
35 Hydrogen fluoride 2
36 Hydrogen sulfide 1
For any of the specific gases shown in column 2, the class of the pressure
receptacle recommended shall be any number up to and including the
corresponding number given in column 3, subject to the provision that when the
filling conditions are such that the developed pressure for the gas at reference
temperature will exceed 7 000 kPa, only a class 1 pressure receptacle shall be
used.
a
Class 1: seamless metallic pressure receptacles.
Class 2: metallic pressure receptacles of welded construction where all
seams have been fully radiographed.
Class 3: metallic pressure receptacles of welded construction where the
seams have been partially radiographed in accordance with an approved
standard.
35
SANS 10019:2011
Edition 7
Table 7 (concluded)
1 2 3
Minimum class
Name of gas of pressure
a
receptacle
37 LPG 3
38 Methane 1
39 Methylamine, di- 3
40 Methylamine, mono- 3
41 Methylamine, tri- 3
42 Methyl bromide 3
43 Methyl chloride 3
44 Monochlorodifluoromethane (R 22) 3
45 Neon 1
46 Nitrogen 1
47 Nitrogen dioxide 3
48 Nitrous oxide 1
49 Octafluorocyclobutane (RC 318) 3
50 Oxygen 1
51 Phosgene 1
52 Propane 3
53 Propylene 3
54 Sulfur dioxide 2
55 Sulfur hexafluoride 3
56 Vinyl chloride 3
For any of the specific gases shown in column 2, the class of the pressure
receptacle recommended shall be any number up to and including the
corresponding number given in column 3, subject to the provision that
when the filling conditions are such that the developed pressure for the
gas at reference temperature will exceed 7 000 kPa, only a class 1
pressure receptacle shall be used.
a
Class 1: seamless metallic pressure receptacles.
Class 2: metallic pressure receptacles of welded construction where all
seams have been fully radiographed.
Class 3: metallic pressure receptacles of welded construction where
the seams have been partially radiographed in accordance with an
approved standard.
36
SANS 10019:2011
Edition 7
Table 8 — Schedule of cylinder valve outlet connections for various gases
1 2 3 4 5 6 7 8
Outlet
Chemical Subsidiary connection Thread
Gas UN No. Class a
symbol risk number or type
descriptionb
1 Acetylene, dissolved 1001 C 2 H2 2.1 – 4 LH female
2 Air 1002 – 2.2 – 3 RH female
3 Ammonia cylinders 1005 NH3 2.3 8 CGA 240c or RH female/
CGA 660c RH male
4 Ammonia drums 1005 NH3 2.3 8 1¾" ACME or RH male
CGA 660c (both)
5 Ammonia U.H.P. 1005 NH3 2.3 8 CGA 720c RH male
6 Argon 1006 Ar 2.2 – 3 RH female
7 Butane 1011 C4H10 2.1 – SANS 199d –
8 Carbon dioxide 1013 CO2 2.2 – 8 RH male
9 Carbon monoxide 1016 CO 2.3 2.1 4 LH female
10 Chlorine 1017 Cl 2.3 8 CGA 660c RH male
11 Ethylene 1962 C 2 H4 2.1 – 4 LH female
12 Ethylene oxide cylinders 1040 C 2 H4 O 2.3 2.1 15 LH male
13 Ethylene oxide (ETO) 1040 C2 H4 O 2.3 2.1 7 LH male
drums
14 ETO/CO2 mixture 1041 C2H4O/CO2 2.1 – 2 LH female
15 Helium 1046 He 2.2 – 3 RH female
16 Hydrogen 1049 H2 2.1 – 4 LH female
17 LPG 1075 C4H10/C3H8 2.1 – SANS 199d –
18 Medical gases – – – – SANS 39e –
19 Methane 1971 CH4 2.1 – 4 LH female
20 Nitrogen 1066 N2 2.2 – ¾" BSP RH female
21 Nitrous oxide 1070 N 2O 2.2 5.1 13 RH male
22 Oxygen 1072 O2 2.2 5.1 3 RH female
d
23 Propane 1978 C3 H 8 2.1 – SANS 199 –
24 Sulfur dioxide 1079 SO2 2.3 8 CGA 240c RH female
25 Sulfur hexafluoride 1080 SF6 2.2 – 6 RH male
BSP = British Standard Pipe
ACME = American Chemical and Mechanical Engineering
a
Class and subsidiary risk shall be in accordance with SANS 10231.
b
Unless otherwise specified, outlet connection numbers shall be from BS 341-1 and BS 341-3.
c
CGA valve numbers for valve outlets shall be in accordance with the Compressed Gas Association of USA’s Valve
Outlet Document, CGA V1.
d
Outlets connections for butane, LPG and propane are specified in SANS 199. See also 5.3.
e
The use of pin index valves is mandatory for all sizes of medical gas pressure receptacles up to and including a water
capacity of 20 L. Above this size the connection is at the discretion of the supplier. Medical gas pressure receptacle valve
outlets using the pin-index system of connections are specified in SANS 39.
37
SANS 10019:2011
Edition 7
Table 9 — Schedule of valve outlets for refrigerants class 2.2
1 2
Description Outlet connection
SANS 50144-1; SANS 1306-1 G ⅝ (BSP) and
Small refillable cylinders (12,3 L water capacity)
1/4" SAE Flare CGA 165a
Large refillable cylinders (62 L water capacity)
BS341-3 No. 6
0,5 ton pressure drums CGA 660a
1,0 ton pressure drums (nominal 900 L water SANS 50144-1; SANS 1306-1 G ⅝ (BSP) and
capacity) BS 341-3 No. 6
High pressure refillable cylinders
BS 341-3 No.6
BSP = British standard pipe
NOTE 1 All outlets are RH male.
NOTE 2 If required, more details regarding refrigerant outlets can be obtained from the South African
Fluorocarbon Association.
a
CGA valve numbers for valve outlets shall be in accordance with the Compressed Gas Association of
USA’s Valve Outlet Document, CGA V1.
Table 10 — SCUBA cylinders outlet connections
Gas Outlet connection Thread type

CGA 850 K-Valve with a clamp (yoke connection), limited N/A
to 23,2 MPa
Breathing air
DIN 477-1 No 13 for up to 20 MPa applications G5/8 5-threads
DIN 477-5 No 56 for 30 MPa applications G5/8 7-threads
EN 144-3 for 23,2 and 30 MPa applications M26 x 2
CGA 850 K-Valve with A-clamp (yoke connection), limited N/A
Oxygen-enriched air to 23,2 MPa
(Nitrox, Trimix)
DIN 477-1 No 13 for up to 20 MPa applications G5/8 5-threads
DIN 477-5 No 56 for 30 MPa applications G5/8 7-threads
38
SANS 10019:2011
Edition 7
Table 11 — Neck threads for cylinders
1 2 3
Cylinder types Threads
1 Class 1 steel cylinders
a) for high pressure industrial service. Large 25 E thread to ISO 10920
diameter cylinders (e.g. cylinder diameter
145 mm and larger)
b) for high pressure industrial service. Small 17 E thread to ISO 11116-1 or
diameter cylinders (e.g. cylinder diameter 18 T thread to BS 341-1 or
140 mm and smaller) 25 E thread to ISO 10920
2 Class 1 aluminium cylinders Parallel thread in conjunction with an effective O-ring
seal (e.g. M 25 × 2 for large cylinders 10 L water
capacity and above, or M 18 × 1,5 for cylinders below
10 L water capacity) or
Threads as specified for class 1 steel cylinders
3 Class 2 and 3 cylinders of water capacity not 18 T thread to BS 341-1 or
exceeding 15 L intended for low-pressure
17 E thread to ISO 11116-1
liquefiable gas (excluding LPG)
½ -14” NGT
4 Class 2 and 3 cylinders of water capacity 25 E thread to ISO 10920 or
exceeding 15 L intended for low-pressure
liquefiable gas (excluding LPG) ¾ – 14 NGT
5 Class 1 and 2 dissolved acetylene cylinders
a) smaller than 10 L 17 E to ISO 11116-1 or 18 T thread to BS 341-1 or 25E
thread to ISO 10920 or W28.8 DIN 477 or 1,025 inch to
BS 341-1
b) 10 L and above 25 E thread to ISO 10920 or W28.8 DIN 477 or
1,025 inch to BS 341-1
6 LPG cylinders Threads specified in SANS 199 (see also 5.3)
7 SCUBA cylinders M 25 × 2 parallel thread in conjunction with an effective
O-ring seal
17E to ISO 11116-1
8 Fire suppressant cylinder necks (cylinders Based on internationally accepted practice in
used in fixed installations only) accordance with UL in the USA
There are cylinders with internal and external
threads and others with only an external
thread:
a) Internal thread G 1 to SANS 1306-1
External thread G 1 1/2 B to SANS 1306-1 and
M 55 × 2 – 8 g to SANS 1700-2-5, SANS 1700-2-6 and
SANS 1700-2-7
b) Internal thread 1 inch NGT
External thread W80X1/11
c) Internal thread None
External thread 2½ inch-12UN-2A
39
SANS 10019:2011
Edition 7
Table 12 — Colour marking of gas cylinders
1 2 3 4 5
Chemical a b
Name of gas Colour of cylinder body Colour(s) of shoulder
symbol
1 Acetylene C2H2 Maroon 8010-R10B
2 Air – French grey 4010-G50Y
c
3 Air, synthetic – Protea 1020-Y80R
4 Ammonia NH3 Aluminium Signal red 1580-Y90R and
Golden yellow 1070-Y20R
5 Argon Ar Peacock blue 5040-B20G
6 Carbon dioxide CO2 Light Brunswick green 5540-G30Y
Carbon Monoxide CO Signal red 1580-Y90R Signal red 1580-Y90R and
7 Chlorine Cl2 Golden yellow 1070-Y20R
8 Chlorine (cylinder with Cl2 Golden yellow 1070-Y20R Black S 9000-N
dip pipe)
9 Ethylene C2H4 Dark violet 5040-R50B Signal red 1580-Y90R
10 Ethylene oxide C2 H4 O Dark violet 5040-R50B Signal red 1580-Y90R and
11 Helium He Middle brown 7020-Y40R
12 Hydrogen H2 Signal red 1580-Y90R
13 Methane CH4 Signal red 1580-Y90R Black (band) S 9000-N
14 Neon Ne Middle brown 7020-Y40R Black S 9000-N
15 Nitrogen N2 French grey 4010-G50Y Black S 9000-N
16 Oxygen O2 Black S 9000-N
17 Special gas – Protea 1020-Y80R
18 Sulfur dioxide SO2 Light Brunswick green 5540-G30Y Golden yellow 1070-Y20R
NOTE The finish of the above paint colours is semi-gloss (sheen).
a
The colours specified are in accordance with the Scandinavian Colour Institute AB, Stockholm, Sweden
(NCS System). Swatches of all the above colours are available from the SABS Standards Information Centre
(see SANS 1091).
b
Where a second colour band is stated, the second band should be adjacent to the shoulder colour.
c
Synthetic air cylinders not intended for breathable use shall be stencilled or have labels affixed to them stating
"NOT FOR BREATHING". This requirement is over and above the normal shoulder label stating the type of
gas in the cylinder. Industrial Synthetic Air and High Purity (Zero Air) shall be labelled accordingly.
NOTE Synthetic Air is made up of pure oxygen and pure nitrogen, the oxygen content being a volume
fraction of 21 %.
40
SANS 10019:2011
Edition 7
Table 13 — Refillable refrigerant cylinder colour chart
1 2 3
Gas reference Colour of cylinder shroud/collar Colour
R22 S0540-G Light Green
R123 S1510-R90B Light Blue Green
R124 S3555-B80G Deep Green
R125 S3030-Y Medium Brown
R134a S0530-B Light Blue
R404a S0580-Y60R Orange
R406a S3020-G40Y Light Green Grey
R407c S3050-Y50R Medium Brown
R408a S2060-R40B Medium Purple
R409a S3020-Y20R Medium Brown Tan
R410a S1040-R20B Rose
R427a S1565-G Brilliant Green
R507 S2050-B70G Blue Green
NOTE 1 The colour references are based on the National Colour System (NCS)
and have been agreed to by the South African Fluorocarbon Association. Colours
for refrigerant gases that are not listed above can be found in (American Society
of Heating, Refrigerating, and Air-Conditioning Engineers) ASHRAE 34.
NOTE 2 R406a is a flammable gas and a red band NCS 1580-Y90R shall be
painted around the cylinder shoulder.
41
SANS 10019:2011
Edition 7
Table 14 — Pre-fill inspection/rejection criteria for

all cylinders other than welded LPG cylinders
1 2
Condition Rejection criteria
Arc or torch burns Localized heat-affected zone plus addition of weld metal or removal
of metal by grinding, filing, etc.
Bulges Visible swelling
Chain pitting, line or channel (or both) When any one condition affects 50 % or more of the diameter of the
corrosion cylinder
Cracks Split in material
Crevice corrosion When this occurs close to an opening in a welded steel cylinder
Or
If the depth is greater than 20 % of the original wall thickness in
welded and seamless cylinders
Cuts or gouges When metal has been removed and the depth of the cut or gouge is
greater than 10 % of the cylinder wall thickness
Dents Dent is greater than 3 % of the cylinder diameter
Or
Diameter of the dent is greater than 15 times the depth of the dent
Depressed bung When the profile of a welded cylinder has changed from the original
shape
Fire damage When there is excessive general or local heating, e.g.
a) burning and charred paint
b) burning of metal
c) distortion of cylinder
d) melting of valve parts
e) melting of any plastic parts, such as test ring, guard or cap
General corrosion If the original surface of the metal cannot be seen
Isolated pits Pits up to 5 mm in diameter
Plug or neck inserts Additional inserts to base or wall, which are not part of the original
design, e.g. pipes, nuts and bolts
Stamping Any stamp markings on the parallel part of the cylinder wall. Any
alterations, illegible, incorrect or inadequate markings
Suspicious marks Marks introduced other than by the manufacturer or an approved
test station
Vertical instability Any stacking of cylinders which creates an unstable condition such
that cylinders might fall
42
SANS 10019:2011
Edition 7
Table 15 — Pre-fill inspection/rejection criteria for LPG welded steel cylinders
1 2
Condition Rejection criteria
Arc or torch burns Localized heat-affected zone plus addition of weld metal or removal
of metal by grinding, filing, etc.
Bulges Visible swelling
Chain pitting, line or channel (or both) When any one condition affects 50 % or more of the diameter of the
corrosion cylinder
Cracks Split in material
Crevice corrosion When this occurs close to an opening in a welded steel cylinder
Or
If the depth is greater than 20 % of the original wall thickness in
welded and seamless cylinders
Cuts or gouges When metal has been removed and the depth of the cut or gouge is
greater than 10 % of the cylinder wall thickness
Dents When the depth of the dent exceeds 25 % of its width at any point
Depressed bung When the profile of the cylinder has changed from the original
shape
Fire damage When there is excessive general or local heating, e.g.
a) burning and charred paint
b) burning of metal
c) distortion of cylinder
d) melting of valve parts
e) melting of any plastic parts, such as test ring, guard or cap
General corrosion If the original surface of the metal cannot be seen
2
Isolated pits When there is more than one pit per 500 mm of the surface area
Plug or neck inserts Additional inserts to base or wall, which are not part of the original
design, e.g. pipes, nuts and bolts
Stamping Any stamp markings on the parallel part of the cylinder wall. Any
alterations, illegible, incorrect or inadequate markings
Suspicious marks Marks introduced other than by the manufacturer or an approved
test station
Vertical instability Any stacking of cylinders which creates an unstable condition such
that cylinders might fall
43
SANS 10019:2011
Edition 7
Annex A
(normative)
List of current approved manufacturing standards for the

importation and manufacture of gas pressure receptacles in South
Africa
A.1 Australia
No. Standard Description

1 AS 1777 Aluminium cylinders for compressed gases − Seamless − 0,1 kg to 130 kg
2 AS 2468 Steel cylinders for compressed gases – Brazed – 0,1 kg to 11 kg
Steel cylinders for compressed gases – Welded three-piece construction with
3 AS 2470
longitudinal joint – 11 kg to 150 kg
4 AS 2527 Cylinders for dissolved acetylene
5 AS 2875 Alloy steel cylinders for compressed gases – Seamless – 0,1 kg to 500 kg
6 AS 3577 Steel cylinders for compressed gases – Welded – 150 kg to 500 kg
A.2 Canada (Canadian Transport Commission Regulations)

1 TC 4BA Welded or brazed cylinders made of definitely prescribed steels
Welded steel cylinders made of definitely prescribed steels with electric-arc welded
2 TC 4BW
longitudinal seam
A.3 France

1 CODAP 2000 Gas cylinders – Seamless steel cylinders for compressed, liquefied or dissolved gases
A.4 Germany (German Institute of Standards, standard specifications)

DIN 4661
1 Gas cylinders, welded steel gas cylinders, test pressure 30 atü
parts 1 to 7
Druckgas
2 Seamless steel gas cylinders
Verordnung
44
SANS 10019:2011
Edition 7
A.5 International Standards Organizations, European Norms, standard

specifications and EEC directives

Council Directive of 17 September 1984 on the approximation of the laws of the Member
1 EEC 84/525
States relating to seamless, steel gas cylinders
2 EEC 84/526
States relating to seamless, unalloyed aluminium and aluminium alloy gas cylinders
3 EEC 84/527
States relating to welded unalloyed steel gas cylinders
Non-refillable metallic gas cartridges for liquefied petroleum gas, with or without a valve,
4 EN 417
for use with portable appliances – Construction, inspection, testing and marking
Cryogenic vessels – Transportable vacuum insulated vessels of not more than 1 000 litres
5 EN 1251-2
volume – Design, fabrication, inspection and testing
LPG equipment and accessories – Transportable refillable welded steel cylinders for LPG
6 EN 1442
– Design and construction
7 EN 1800 Transportable gas cylinders – Acetylene cylinders – Basic requirements and definitions
Transportable gas cylinders – Specification for the design and construction of refillable
transportable seamless steel gas cylinders of water capacities from 0,5 litre up to and
8 EN 1964-1
including 150 litres – Part 1: Cylinders made of seamless steel with an Rm value of less
than 1 100 MPa
transportable seamless steel gas cylinders of water capacities from 0,5 litre up to and
9 EN 1964-2 including 150 litres – Part 2: Cylinders made of seamless steel with an Rm value of
1 100 MPa and above
10 EN 1975 transportable seamless aluminium and aluminium alloy gas cylinders of capacity from 0,5
litre up to 150 litre
11 EN 12205 Transportable gas cylinders – Non-refillable metallic gas cylinders
12 EN 12245 Transportable gas cylinders – Fully wrapped composite cylinders
13 EN 12862
transportable welded aluminium alloy gas cylinders
transportable seamless normalized carbon manganese steel gas cylinders of water
14 EN 13293 capacity up to 0,5 litre for compressed, liquefied and dissolved gases and up to 1 litre for
carbon dioxide
Transportable gas cylinders – Refillable welded steel gas cylinders – Design and
15 EN 13322-1
construction – Part 1: Carbon steel
Transportable refillable welded steel cylinders for LPG – Alternative design and
16 EN 14140
construction
Transportable gas cylinders – Specification for welded pressure drums up to 1 000 litre
17 EN 14208
capacity for the transport of gases – Design and construction
18 ISO 3807-1 Cylinders for acetylene – Basic requirements – Part 1: Cylinders without fusible plugs
A.5 (concluded)
45
SANS 10019:2011
Edition 7

19 ISO 3807-2 Cylinders for acetylene – Basic requirements – Part 2: Cylinders with fusible plugs
Gas cylinders – Refillable seamless steel gas cylinders – Design, construction and
20 ISO 9809-1 testing – Part 1: Quenched and tempered steel cylinders with tensile strength less than
1 100 MPa
21 ISO 9809-2 testing. – Part 2: Quenched and tempered steel cylinders with tensile strength greater
than or equal to 1 100 MPa
22 ISO 9809-3
testing – Part 3: Normalized steel cylinders
23 ISO 11118 Gas cylinders – Non-refillable metallic gas cylinders – Specification and test methods
Gas cylinders of composite construction – Specification and test methods – Part 1:
24 ISO 11119-1
Hoop wrapped composite gas cylinders
Gas cylinders of composite construction – Specification and test methods – Part 2: Fully
25 ISO 11119-2
wrapped fibre reinforced composite gas cylinders with load-sharing metal liners
Gas cylinders of composite construction – Specification and test methods – Part 3: Fully
26 ISO 11119-3 wrapped fibre reinforced composite gas cylinders with non-load-sharing metallic or non-
metallic liners
Gas cylinders – Refillable seamless steel tubes for compressed gas transport, of water
27 ISO 11120
capacity between 150 L and 3 000 L – Design construction and testing
Gas cylinders - Refillable seamless steel gas cylinders - Acoustic emission testing (AT) for
28 ISO 16148
periodic inspection
Gas cylinders – Refillable welded aluminium-alloy cylinders – Design, construction and
29 ISO 20703
testing
Gas cylinders – Transportable refillable welded steel cylinders for liquefied petroleum
30 ISO 22991
gas (LPG) – Design and construction.
A.6 Italy (Higher Institute for Accident Prevention and Safety at Work
(Istituto Superiore per la Prevenzione e la Sicurezza del Lavoro) ISPESL
rules)

1 VSR Rules Collection (Raccolta VSR) concerning design rules for pressure vessels
Italian Regulations
2 Design and independent inspection of gas cylinders (SAIGAS)
(series XIX of NI)
46
SANS 10019:2011
Edition 7
A.7 Japan

1 JIS B 8240 Construction of pressure vessels for refrigeration
2 JIS B 8241 Seamless steel gas cylinders
A.8 Luxfer Limited, standard specification

1 Luxint Luxfer gas cylinder specification: For the manufacture of aluminium cylinders
A.9 United Kingdom

Transportable gas containers. Specification for steel containers of 0,5 L up to 450 L water
1 BS 5045-2
capacity with welded seams
Transportable gas containers. Specification for seamless containers of less than 0,5 litre
2 BS 5045-6
water capacity
Transportable gas containers. Specification for seamless steel gas containers of water
3 BS 5045-7
capacity 0,5 L up to 15 L for special portable applications
Transportable gas containers. Specification for seamless aluminium alloy gas containers of
4 BS 5045-8 water capacity 0,5 L up to 15 L and up to 300 bar charged pressure at 15 ºC for special
portable applications
Gas cylinders – In situ, non-destructive examination and testing of refillable seamless
5 BS 8562 steel tubes of water capacity between 150 L and 3000 L, used for compressed gases –
Specification
47
SANS 10019:2011
Edition 7
A.10 United States (Department of Transportation Regulations (Code of

Federal Regulations Title 49))

ASME-BPVC
Section VIII, Boiler and pressure vessel code – Section VIII: Rules for the construction of pressure
1
Divisions 1 vessels
and 2
2 DOT 3A Seamless steel cylinders up to 1 000 lbs water volume. Service pressure 150 psi minimum
Seamless steel cylinders made of definitely prescribed steels up to 1 000 lbs water volume.
3 DOT 3AA
Service pressure 150 psi minimum
Seamless aluminium cylinders up to 1 000 lbs water volume and minimum service pressure
4 DOT 3AL
150 psi
Seamless stainless steel cylinders of capacity over 1 000 lbs water volume. Service pressure
5 DOT 3AX
at least 500 psi
Seamless steel cylinders made of definitely prescribed steel of capacity over 1 000 lbs water
6 DOT 3AAX
volume. Service pressure 500 psi minimum
Seamless steel cylinders with a maximum out side diameter 2 inches. Service pressure
7 DOT 3E
1 800 psi maximum
Seamless steel cylinder with minimum water capacity 1 000 pounds and minimum service
8 DOT 3T
pressure 1 800 psi
9 DOT 4A Forge Welded steel cylinders
Welded steel cylinders made from low carbon steel up to 1 000 lbs water volume. Service
10 DOT 4B
pressure between 150 and 500 psi
Welded aluminium cylinders made of definitely prescribed aluminium up to 1 000 lbs water
11 DOT 4E
volume. Service pressure between 225 and 500 psi
Welded steel cylinders made of definitely prescribed steels up to 1 000 lbs water volume.
12 DOT 4BA
Service pressure between 225 and 500 psi
Welded steel cylinders made of definitely prescribed steels with electric-arc welded
13 DOT 4BW
longitudinal seam. Service pressure between 225 and 500 psi
Welded insulated cylinders with a water capacity not over 1 000 pounds and a service
14 DOT 4L
pressure of at least 40 but not greater than 500 psi
Steel cylinders with approved porous filling for acetylene. Service pressure 250 psi.
15 DOT E7638
Incorporates CGA C-12
Welded steel cylinders made of definitely prescribed steel for the transportation of acetylene.
16 DOT 8
Service pressure 250 psi. Incorporates CGA C-12
Non-reusable (non-refillable) cylinders. Service pressure not to exceed 80 % of the test
17 DOT 39
pressure
Welded steel cylinders made of definitely prescribed steels electric-arc welded longitudinal
18 DOT E-10320
seam for the transportation of acetylene
48
SANS 10019:2011
Edition 7
A.10 (concluded)

Steel cylinders with approved porous filling for acetylene. Service pressure 250 psi.
19 DOT 8AL
Incorporates CGA C-12
Non-reusable (non-refillable) cylinders. Service pressure not to exceed 80 % of the test
20 DOT 39
pressure
Welded steel cylinders made of definitely prescribed steels electric-arc welded longitudinal
21 DOT E-10320
seam for the transportation of acetylene
A.11 South Africa

1 SANS 220 Dissolved acetylene cylinders
Transportable refillable welded stainless steel cylinders for low pressure gases –
2 SANS 399
Alternative design and construction
3 SANS 1151 Portable rechargeable fire extinguishers – Halogenated hydrocarbon type extinguishers
SANS 1475
4 The production of reconditioned fire-fighting equipment
Parts 1 and 2
Transport of dangerous goods – Design, construction, testing, approval and maintenance
5 SANS 1518
of road vehicles and portable tanks
6 SANS 1567 Portable rechargeable fire extinguishers – CO2 type extinguishers
7 SANS 1739 Low pressure welded steel cylinders for fire extinguishers
8 SANS 1910 Portable refillable fire extinguishers
9 SANS 4706 Gas cylinders – Refillable welded steel cylinders – Test pressure 60 bar and below
Gas cylinders – Refillable seamless aluminium alloy gas cylinders – Design, construction
10 SANS 7866
and testing
SANS 9809 Gas cylinders – Refillable seamless steel gas cylinders – Design, construction and testing
11
Parts 1 to 3
Transportable containers for compressed, dissolved and liquefied gases – Basic design,
12 SANS 10019
manufacture, use and maintenance
Uniform provisions concerning I. approval of specific equipment of motor vehicles using
liquefied petroleum gases in their propulsion system, II. approval of a vehicle fitted with
13 SANS 20067
specific equipment for the use of liquefied petroleum gases in its propulsion system with
regard to the installation of such equipment
Uniform provisions concerning the approval of: I. Specific components of motor vehicles
using compressed natural gas (CNG) in their propulsion system; II Vehicles with regard to
14 SANS 20110
the installation of specific components of an approved type for the use of compressed
natural gas (CNG) in their propulsion system
49
SANS 10019:2011
Edition 7
Annex A1
(normative)
List of special conditions applicable to current approved

manufacturing standards for the importation and
manufacture of gas pressure receptacles in South Africa
Annex A
Standard Description Comments
No.
A1 Steel cylinders for compressed gases – Cylinders shall be fitted with a pressure
AS 2468
Line 2 Brazed – 0,1 kg to 11 kg relief device
A5 LPG Equipment and accessories – Welded steel cylinders manufactured for
Line 4 Transportable refillable welded steel all liquefied gases, including LPG shall
EN 1442
cylinders for LPG – Design and be normalised and the cylinder shall be
construction stamped with the letter ‘N’.
A5 Gas cylinders – Transportable refillable Note: Non heat treated cylinders are not
Line 28 welded steel cylinders for liquefied permitted for importation and use in
ISO 22991
petroleum gas (LPG) – Design and South Africa.
construction
50
SANS 10019:2011
Edition 7
Annex B
(informative)
Pressure receptacle valve standards

Reference can be made to CGA, EN or ISO valve design, manufacture and test standards as follows:
CGA 600, Valve outlet connections 1.000 – 20 UNEF-RH.EXT.
ISO 10297, Transportable gas cylinders – Cylinder valves – Specification and type testing.
ISO 13340, Transportable gas cylinders – Cylinder valves for non-refillable cylinders – Specification and
prototype testing.
ISO 15996, Gas cylinders – Residual pressure valves – General requirements and type testing.
ISO 22435, Gas cylinders – Cylinder valves with integrated pressure regulators – Specification and type
testing.
SANS 39/ISO 407, Small medical gas cylinders – PIN-index yoke-type valve connections.
51
SANS 10019:2011
Edition 7
Annex C
(normative)
Frequency of inspections and tests for pressure receptacles

The test periods indicated in table C.1 shall be used providing the dryness of the product and that of the
filled cylinder are such that there is no free water. This condition shall be proven and documented within
a quality system of the filler. If these conditions cannot be fulfilled, alternative or more frequent testing
may be appropriate.
At all times, certain requirements may necessitate a shorter time interval, e.g. the dew point of the gas,
polymerization reactions and decomposition reactions, cylinder design specifications, change of gas
service, etc.
The retest periods shall also be applicable to pressure receptacles used in fixed fire installations.
Pressure receptacles used in back up or buffer service in systems or process systems shall be retested
as per the frequencies given in table C.1.
52
SANS 10019:2011
Edition 7
Table C.1 — Intervals for periodic inspections and tests
1 2 3
Frequency of inspection and
Description Gas type (examples) b
test (years)
Compressed gases Ar,N2,He 10
a
H2 10
Air, O2 10
Self-contained breathing air, O2 2 year internal, 4 year hydrostatic
test
Gases for underwater breathing 1 year internal, 4 year hydrostatic
apparatus test
Medical gases and breathing air 10
c
CO 5
Acetylene
Monolithic mass Internal inspection every
10 yearsf
f
Non-monolithic mass Acetylene Internal inspection every 2 years
e
Liquefied gases Refrigerants, CO2, LPG 10
d
Corrosive gases 5
Toxic gases that are non-corrosive SO2, F2 5
Very toxic gases that are non-corrosive AsH3, PH3, etc 5
Gas mixtures All mixtures 5 years and 10 years according to
dangerous properties
Mixtures that are toxic or
corrosive have a 5 year interval,
and other mixtures have a
10 year interval
Composite cylinders All gases Refer to SANS 11623
a
Particular attention shall be paid to the tensile strength and surface conditions of such cylinders. Cylinders not
in conformance with the special hydrogen requirements shall be withdrawn from hydrogen service. See
ISO 11821 for possible additional testing.
b
Periodic inspections and test frequency given in this table shall override any international standard inspection
test requirements for pressure receptacles.
c
This product requires very dry gas. See ISO 11114-1.
d
Corrosivity is with reference to human tissue (see ISO 13338) and NOT cylinder material as indicated in
annex D.
e
LPG cylinders are exempt from the requirements but shall be internally inspected whenever they are
hydrostatically tested.
f
Acetylene cylinders shells to be hydrostatically tested every time the porous material is removed.
53
SANS 10019:2011
Edition 7
Annex D
(normative)
Schedule of SCUBA and SCBA cylinder colour coding and labels
Gas type
Description
Air Pure oxygen Nitrox Trimix
Body colour Golden Yellow Black Golden Yellow Golden Yellow
1070-Y20R S 9000-N 1070-Y20R 1070-Y20R
Shoulder colour French Grey White S French Grey French Grey
4010-G50Y 0500-N 4010-G50Y 4010-G50Y
Adhesive band colour N/A N/A Cleara Cleara
Adhesive band size N/A N/A 300 mm × 80 mm 300 mm × 80 mm
Lettering N/A N/A NITROX TRIMIX
Lettering colour N/A N/A Green Green
Contents label (as specified) N/A N/A NEEDED NEEDED
a
The adhesive band is normally clear and the colour of the cylinder body should show through with the words
of the type of gas in the correct letter colouring.
OXYGEN %
NITROX
Drg.335g
OXYGEN %
TRIMIX HELIUM %
Drg.335h
54
SANS 10019:2011
Edition 7
Annex E
(normative)
Placement of cylinders
Drg.335e
Figure E.1 — Correct and incorrect placement of cylinders
Drg.3335f
Figure E.2 — Directional arrows on cylinders
55
SANS 10019:2011
Edition 7
Annex F
(informative)
Developed pressure for permanent gases

Figure F.1 shows the effect of the change of reference temperature from 20 °C to 15 °C up to 65 °C on
the developed pressure of permanent gases, except for methane, in cylinders. The increase in pressure
does not make any of the approved cylinder specifications unsafe in normal service.
Figure F.1 — Various developed pressures
56
SANS 10019:2011
Edition 7
Bibliography
Standards
AS 2030, Rules for the approval, filling, inspection, testing and maintenance of cylinders for the storage
and transport of compressed gases.
CGA S-1.1, Pressure relief device standard – Part 1 – Cylinders for compressed gases.
ISO 11372, Gas cylinder – cylinders for dissolved acetylene – inspection at time of filling.
ISO 13088, Gas cylinders – Acetylene cylinder bundles – Filling conditions and filling inspection.
ISO 13338, Determination of tissue corrosiveness of a gas or gas mixture.
SANS 407, Austenitic manganese steel castings.
SANS 532, Standard and specifications for industrial, medical, propellant, food and beverage gases,
refrigerants and breathing gases.
SANS 1567, Portable rechargeable fire extinguishers – CO2 type extinguishers.
SANS 1572, CO2 gas cartridges (steel).
SANS 10108, The classification of hazardous locations and the selection of apparatus for use in such
locations.
Other publications
ARI Guideline N-2002, Assignment of refrigerant container colors. Air-Conditioning and Refrigeration
Institute, Arlington, Virginia 22203, USA.
European Industrial Gases Association, EIGA IGC Doc. 33/06, Cleaning of equipment for oxygen
service – Guidelines
European Industrial Gases Association, EIGA IGC Doc. 80/08, Handling gas container emergencies.
European Industrial Gases Association, EIGA Doc. IGC 91/03/E, Use of pressure relief devices for gas
cylinders.
European Industrial Gases Association, EIGA Doc. IGC 138/08/E, PTFE tape as a sealant for
cylinder/valve connections.
NOTE EIGA documents are available on the EIGA website (www.eiga.org).
© SABS
57
This page has been left blank intentionally
SABS – Standards Division
The objective of the SABS Standards Division is to develop, promote and maintain South African
National Standards. This objective is incorporated in the Standards Act, 2008 (Act No. 8 of 2008).
Amendments and Revisions
South African National Standards are updated by amendment or revision. Users of South African
National Standards should ensure that they possess the latest amendments or editions.
The SABS continuously strives to improve the quality of its products and services and would
therefore be grateful if anyone finding an inaccuracy or ambiguity while using this standard would
inform the secretary of the technical committee responsible, the identity of which can be found in
the foreword.
Tel: +27 (0) 12 428 6666 Fax: +27 (0) 12 428 6928
The SABS offers an individual notification service, which ensures that subscribers automatically
receive notification regarding amendments and revisions to South African National Standards.
Tel: +27 (0) 12 428 6883 Fax: +27 (0) 12 428 6928 E-mail: sales@sabs.co.za
Buying Standards
Contact the Sales Office for South African and international standards, which are available in both
electronic and hardcopy format.
Tel: +27 (0) 12 428 6883 Fax: +27 (0) 12 428 6928 E-mail: sales@sabs.co.za
South African National Standards are also available online from the SABS website
http://www.sabs.co.za
Information on Standards
The Standards Information Centre provides a wide range of standards-related information on both
national and international standards, and is the official WTO/TBT enquiry point for South Africa. The
Centre also offers an individual updating service called INFOPLUS, which ensures that subscribers
automatically receive notification regarding amendments to, and revisions of, international
standards.
Tel: +27 (0) 12 428 6666 Fax: +27 (0) 12 428 6928 E-mail: info@sabs.co.za
Copyright
The copyright in a South African National Standard or any other publication published by the SABS
Standards Division vests in the SABS. Unless exemption has been granted, no extract may be
reproduced, stored in a retrieval system or transmitted in any form or by any means without prior
written permission from the SABS Standards Division. This does not preclude the free use, in the
course of implementing the standard, of necessary details such as symbols, and size, type or grade
designations. If these details are to be used for any purpose other than implementation, prior written
permission must be obtained.
Details and advice can be obtained from the Senior Manager.

Tel: +27 (0) 12 428 6666 Fax: +27 (0) 12 428 6928 E-mail: info@sabs.co.za

SANS10019 2011 Ed7

Uploaded by

Copyright:

Available Formats

SANS10019 2011 Ed7

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

SANS10019 2011 Ed7

Uploaded by

Copyright:

Available Formats

Copyright protected.

SOUTH AFRICAN NATIONAL STANDARD

Transportable pressure receptacles for

Published by SABS Standards Division

This document was published in September 2011.

This document supersedes SANS 10019:2008 (edition 6).

2 Normative references ............................................................................................................ 3

4 Design and manufacturing requirements .............................................................................. 10

6 Pressure relief devices .......................................................................................................... 16

7 Revalidation of pressure receptacles .................................................................................... 18

8 Marking, labelling, colour coding and certificates ................................................................. 19

9 Filling of pressure receptacles .............................................................................................. 23

10 Handling, storage, transportation and use ............................................................................ 25

11 General safety precautions ................................................................................................... 26

Table 1 Reference temperatures ............................................................................................ 27

Table 2 Properties and pressure groups of permanent gases ............................................... 28

Table 3 Permanent gases: charging pressures and corresponding

Table 4 Permanent gases: developed pressures and corresponding

Table 5 High-pressure liquefiable gases ............................................................................... 31

Table 6 Low-pressure liquefiable gases ................................................................................ 33

Table 7 Class of pressure receptacles for specific gases ...................................................... 35

Table 9 Schedule of valve outlets for refrigerants class 2.2 .................................................. 38

Table 10 SCUBA cylinders outlet connections ........................................................................ 38

Table 11 Neck threads for cylinders ........................................................................................ 39

Table 12 Colour marking of gas cylinders ............................................................................... 40

Table 13 Refillable refrigerant cylinder colour chart ................................................................ 41

Table 14 Pre-fill inspection/rejection criteria for all cylinders other than

Annex A (normative) List of current approved manufacturing standards for the

Annex A1 (normative) List of special conditions applicable to current approved

Annex B (informative) Pressure receptacle valve standards .................................................. 51

Annex E (normative) Placement of cylinders ......................................................................... 55

Annex F (informative) Developed pressure for permanent gases ........................................... 56

Transportable pressure receptacles for compressed, dissolved and

ADR P200, Gas cylinders – Safe use of gas cylinders.

BS 341-3, Transportable gas container valves – Valve outlet connections.

BS 341-4, Transportable gas container valves – Pressure relief devices.

ISO 7225, Gas cylinders – Precautionary labels.

ISO 11621, Gas cylinders – Procedures for change of gas service.

ISO 11622, Gas cylinders – Conditions for filling gas cylinders.

ISO 13341, Transportable gas cylinders – Fitting of valves to gas cylinders.

ISO 13769, Gas cylinders – Stamp marking.

SANS 162/ISO 10286, Gas cylinders – Terminology.

SANS 1091, National colour standard.

SANS 1274, Coatings applied by the powder-coating process.

SANS 10263-0, The warehousing of dangerous goods – Part 0: General requirements.

SANS 10297, The reconditioning of external LPG cylinder valves.

c) within the scope of SANS 10400: the local authority concerned

a) routine inspection of gas pressure receptacles;

b) testing and repair of pressure receptacles in accordance with SANS 1825;

4 Design and manufacturing requirements

a) Refillable welded stainless steel cylinders: SANS 399.

i) Hooped wrapped composite cylinders: ISO 11119-1.

m) Welded transportable vessels of water capacity 501 L to 3 000 L: SANS 1518.

p) Welded aluminium alloy gas cylinders up to 150 L: ISO 20703.

r) Non refillable metallic gas cylinders: DOT 39.

s) Non refillable metallic gas cylinders: ISO 11118.

t) Non refillable metallic gas cylinders: EN 12205.

4.2 Additional design requirements for pressure receptacles

4.3 Heat treatment