SIPS INDUSTRIES - Typical Details - Rev D-Version 1

TYPICAL DETAILS
SIPSTypical Details-Version 1
DETAIL LIST AND DESCRIPTION
DETAIL LIST
DRAWING NUMBER DETAIL NUMBER DETAIL DESCRIPTION REVISION
D01 DETAIL LIST D

D100 Introduction Introduction D
D101 Detail 101 SIPS Corner Set Out Plan D
D102 Detail 102 Sole Plate Set Out Guide D
D103 Detail 103 Sole Plate - Concrete Fixing D
D104 Detail 104 Sole Plate - Concrete Fixing D
D105 Detail 105 Concrete Slab Edge Detailing D
D106 Detail 106 Concrete Set Down Detailing D
D107 Detail 107 Sole Plate - Joist Floor Fixing D
D108 Detail 108 Sole Plate - Joist Floor Fixing D
D109 Detail 109 Sole Plate - SIPS Floor Fixing D
D110 Detail 110 Sole Plate - SIPS Floor Fixing D
D111 Detail 111 SIPS FLOOR Set Down D
D112 Detail 112 SIPS FLOOR - Joist Set Down D
D200 Detail 200 Timber Joining Spline - Plan D
D201 Detail 201 SIPS Joining Spline - Plan D
D202 Detail 202 Steel Column in SIPS - Plan D
D203 Detail 203 Steel Column in SIPS - Corner Plan D
D204 Detail 204 SIPS to Existing Brick - Plan D
D205 Detail 205 Intermediate Joisted Floor - Continuous SIPS Wall D
D206 Detail 206 Intermediate Joisted Floor - Typical D
D207 Detail 207 LVL Beam Detail D
D208 Detail 208 Window Detail - POLAR -Horizontal Weatherboard D
D209 Detail 209 Window Detail - POLAR -Horizontal Weatherboard D
D210 Detail 210 SIPS Wall and Box Beam Assembly D
D211 Detail 211 SIPS Wall and Box Beam Assembled D
D212 Detail 212 SIPS Box Beam Detailing D
D213 Detail 213 Point Load Stud Hold Down D
D214 Detail 214 BOUNDARY WALL DETAIL D
D215 Detail 215 BOUNDARY WALL GUTTER D
D216 Detail 216 PARTY WALL 60/60/60 D
D217 Detail 217 PARTY WALL 90/90/90 D
D218 Detail 218 Window Tape and Flashing D
D219 Detail 219 Batten Space Ventilation D
D301 Detail 301 ROOF EAVES - TYPICAL D
D302 Detail 302 ROOF EAVES - SQUARE CUT D
D303 Detail 303 ROOF SCILLION DETAIL D
D304 Detail 304 ROOF EAVES - CONCEALED GUTTER D
D305 Detail 305 ROOF EAVES - SIPS CEILING D
D306 Detail 306 ROOF EAVES - SIPS CEILING - FLUSH GUTTER D
D307 Detail 307 ROOF EAVES - SIPS CEILING - CONCEALED GUTTER D
D308 Detail 308 SKILLION - EXTENDED ROOF SPLINE D
D309 Detail 309 EACES DETAIL - TRAD FRAMED ROOF D
D310 Detail 310 RIDGE DETAILS- TYPICAL AND HIDDEN D
D311 Detail 311 VELUS - FLAT ROOF -(FCM) D
D312 Detail312 ROOF BARGE - TYPICAL D
DISCLAIMER
THE DETAILS PORTRAYED IN THIS MANUAL ARE FOR DESIGNERS REFERENCE AND GUIDANCE ONLY. THESE ARE SIPS INDUSTRIES PRODUCT TYPICAL
DETAILS. THE DETAILS INCLUDED ARE NOT DEFINITIVE AND WILL LACK THE WATERPROOFING, FINISHING AND OFTEN THE SPECIFIC ENGINEERING OF A
PARTICULAR PROJECT. CARE MUST BE TAKEN WHEN REPLICATING THESE DETAILS TO ENSURE THE SPECIFIC PROJECT DETAILS ARE ENTIRELY
CORRECT. DETAILS ARE FOR REFERENCE, CLARITY OF INFORMATION AND ARE NOT CONCLUSIVE, SHOULD YOU NEED MORE CLARITY OF DETAILING OR
WISH TO SEE ADDITIONAL DETAILING, PLEASE CONTACT SIPS INDUSTRIES TECHNICAL TEAM. SIPS INDUSTRIES DO NOT ACCEPT ANY LIABILITY FOR
PROJECT DETAILING.
Detail Title DETAIL LIST D01

D
DTL No: REV
REFER TO SIPS INDUSTRIES FLOOR, WALL AND ROOF SPECIFICATIONS FOR STRUCTURAL AND
FIXING INFORMATION, TO BE REVIEWED IN CONJUNCTION WITH THESE DETAILS.
SIPS INDUSTRIES HAVE WORKED ON MANY VARIOUS PROJECTS AND THE DETAILS HEREWITH ARE
MERELY TYPICAL CONSTRUCTION DETAILS, FOR ADDITIONAL DETAILS OR MORE COMPLEX
DETAILS, THERE IS A GOOD POSSIBILITY THAT SIPS INDUSTRIES HAVE DETAILS THAT MAY ASSIST,
PLEASE CONTACT SIPS INDUSTRIES TECHNICAL DEPARTMENT FOR SUCH INFORMATION
SIPS INDUSTRIES WILL UPDATE SPECIFICATIONS AND DETAILS ON A REGULAR BASIS AS REQUIRED
BY INDUSTRY STANDARDS OR PRODUCT AMENDMENTS REQUIRE, IT IS ADVISED YOU CHECK OUR
WESITE DOWNLOAD SECTION [WWW.SIPSINDUSTRIES.COM.AU] TO ENURE YOU HAVE THE
CURRENT FILES.
Detail Title Introduction D100

D
DTL No: REV
Corner Set Out
-plate + 12mm- X
Pull dimensions from inside Face of Set Out Plate
90
°
12 Ensure the Gap is maintained

for panel to slot in
13
120 Sole Plate

12
Edge of Slab/ Floor
BREATHER MEMBRANE
BATTENED CAVITY
CLADDING FINISH
FOAM GLUE LINE - CONTINUOUS
SIPS BUGEL HEAD SCREW
Detail Title Detail 101 D101

D
DTL No: REV
Sole Plate Set Out
115 115
SIPS SIPS
102 X
ENSURE SLAB EDGE IS CHECK ENGINEERING

FOR FIXING SPEC
NEAT AND STRAIGHT.
TO AT LEAST 150mm BFL
145 115
SIPS SIPS
132 X
CHECK ENGINEERING
FOR FIXING SPEC
165 115
SIPS SIPS
152 X
ENSURE SLAB EDGE IS CHECK ENGINEERING

FOR FIXING SPEC
NEAT AND STRAIGHT.

D
DTL No: REV
Sole Plate Section - Concrete Floor Part 1
SIPS INDUSTRIES EXTENAL WALL PANEL
Set Sole Plates 12mm

in from floor edge
Snap Chalk Line

12
Damp Proof Course
/ Termite Barrier
BOTTOM BATTEN
VERTICAL HOLES DRILLED
AT 600 C/C, WRAPPED WITH
INSECT CONTROL MESH
100 AND TAPED
Dynabolts min 100mm

from slab edge.
Chemical Anchors
to be centered on Sole Plate
BOLTS TO BE 900mm C/C

UNLESS OTHERWISE SPECIFIED
BY THE PROJECT ENGINEER

D
DTL No: REV
Sole Plate Section - Concrete Floor Part 2
PROCTOR WALL WRAP

BREATHABLE MEMBRANE
SIPS INDUSTRIES VAPOUR BARRIER
EXTENAL WALL PANEL
BATTEN/CAVITY
PLASTERBOARD
SELECTED CLADDING
CLOSING BATTEN
100

D
DTL No: REV
Concrete Slab Detailing
PROCTOR WALL WRAP

BREATHABLE MEMBRANE
VAPOUR BARRIER SIPS INDUSTRIES EXTERNAL WALL
PANEL
BATTEN/CAVITY
PLASTERBOARD
SELECTED CLADDING
DAMP PROOF COURSE /

TERMITE BARRIER
CLOSING BATTEN - H3
ENSURE SLAB EDGE IS

NEAT AND STRAIGHT.

D
DTL No: REV
Concrete Set-Down Detail
PROCTOR WALL WRAP

BREATHABLE MEMBRANE
VAPOUR BARRIER
BATTEN/CAVITY
SELECTED CLADDING
WET AREA SET DOWN
CLOSING BATTEN - H3
WHERE WET AREA STOPS.

THE SLAB UPSTAND MUST BE
NEAT AND STRAIGHT
ENSURE CONCRETE UPSTAND IS

FORMED AND IS NEAT AND LEVEL
WITH GENERAL SLAB SURFACE.
140-145mm THICK

D
DTL No: REV
Sole Plate Section - Joist Floor Part 1
SIPS INDUSTRIES
EXTENAL WALL PANEL
Set Sole Plates 12mm
in from floor edge
132
Snap Chalk Line 12
Perimeter Beam
Dashed indicates
Alternative Joist
Direction / Span

D
DTL No: REV
Sole Plate Section - Joist Floor Part 2
PROCTOR WALL WRAP

BREATHABLE MEMBRANE
EXTENAL WALL PANEL
BATTEN/CAVITY
PLASTERBOARD
SOLE PLATE FIXING TO EACH

SELECTED CLADDING
JOIST STRICTLY TO THE ENGINEERS
SPECIFICATIONS
Dashed indicates
Alternative Joist
Direction / Span
JOISTS FIXED TO TOP PALTE

IN STRICT ACCORDANCE TO
JOIST MANUFACTURERS
OR TIMBER CODE GUIDELINES

D
DTL No: REV
Sole Plate Section - SIPS Floor Part 1
SIPS INDUSTRIES EXTENAL WALL PANEL
SET SOLE PLATES 12mm Sole Plate +12mm

IN FLOOR FROM EDGE
SNAP CHALK LINE 12 See SIPs Fixing Schedule

FOR SET OUT
End Timber
SIPS INDUSTRIES FLOOR PANEL
DPC
SIPS FLOOR PANELS ARE TO BE

FIXED TO BEARERS WITH 225mm
SIPS SCREWS FIXED AT 300mm C/C
UNLESS OTHERWISE SPECIFIED
BY ENGINEER

D
DTL No: REV
Sole Plate Section - SIPS Floor Part 2
PROCTOR WALL WRAP

SIPS INDUSTRIES BREATHABLE MEMBRANE
EXTENAL WALL VAPOUR BARRIER
PANEL
BATTEN/CAVITY
PLASTERBOARD
SELECTED CLADDING
FLOORING
CLOSING BATTEN
SEE SIPS FIXING

SCHEDULE FOR
SOLE PLATE FIXINGS
BEARER BEAM TO ENGINEERS

SPECIFICATION

D
DTL No: REV
SIPS Floor -Set Down Detail SIPS
SIPS INDUSTRIES
INTERNAL WALL PANEL WATER RESISTANT
WALL LINING
PLASTERBOARD
WATER PROOFING AND
TILING BY OTHERS
FLOORING
WATER RESISTANT
SECURA FLOORING
OR SIMILAR
175 SIPS INDUSTRIES FLOOR PANEL

115 SIPS INDUSTRIES FLOOR PANEL
ADDITIONAL COUNTER BEARER SERVICE AREA

SPECIFICATION

D
DTL No: REV
SIPS Floor -Set Down Detail
SIPS INDUSTRIES
INTERNAL WALL PANEL WATER RESISTANT
WALL LINING
PLASTERBOARD
WATER PROOFING AND
TILING BY OTHERS
FLOORING
WATER RESISTANT
SECURA FLOORING
OR SIMILAR
ADDITIONAL COUNTER BEARER
INSULATION AND SERVICE AREA

SPECIFICATION

D
DTL No: REV
Joining Spline - Double Stud
Double Stud
2/ 35mm MGP10 Electrical Conduit
Panels Slide over

Panels Slide over
Joining Spline
Joining Spline
PRE-ASSEMBLED WALL Continuous Glue Line

Nails are Scew Fixed
70mm Ringshank Nails @150mm centers
ASSEMBLED SIPS WALL
Internal Plasterboard/Lining
FINISHED WALL Breathable Membrane

Ventilated Air CAvity - Min 19mm
Vertical Battens
Cladding Material

D
DTL No: REV
Joining Spline - SIPS Spline
Typical SIPS Spline Electrical Conduit
Panels Slide over

Joining Spline Panels Slide over
Joining Spline
70
PRE-ASSEMBLED WALL
Continuous Glue Line
ASSEMBLED SIPS WALL


Ventilated Air CAvity - Min 19mm
Vertical Battens
Cladding Material

D
DTL No: REV
Steel Column in SIPS Wall
Steel Column to
Engineers Spec Timber to Suit
Panels Slide over Panels Slide over

Joining Spline Joining Spline
Electrical Conduit
PRE-ASSEMBLED WALL Continuous Glue Line

35mm MGP10 Fix timber to column
ASSEMBLED SIPS WALL


Ventilated Air Cavity - Min 19mm
Vertical Battens
Cladding Material

D
DTL No: REV
Steel Corner Column
Steel Column to
Engineers Spec
35mm MGP10
Continuous Glue Line

@150mm centers
Breathable Membrane
Cladding Material
Vertical Battens
Ventilated Air Cavity - Min 19mm

D
DTL No: REV
SIPS to EXISTING BRICK - PLAN
SIPS PANEL OVER TIMBER

EXISTING BRICKWORK
PLATE FIXED PER SIPS
FIXING SCHEDULE RAMSET ANKASCREW OR AS
SPECIFIED BY ENGINEER
35mm MGP10 DPC
PLAN

D
DTL No: REV
Intermediate Floor Section - Continuous Wall Panel
PROCTOR WALL WRAP
IF EXTERNAL WALL
BREATHABLE MEMBRANE
EXTENAL WALL PANEL
BATTEN/CAVITY
PLASTERBOARD
SELECTED CLADDING
Dashed indicates (if applicable)
Alternative Joist
Direction / Span
FIX LVL OR TIMBER PERIMETER JOISTS

TO SIPS PANEL WITH STRUCTURAL
ADHESIVE AND TEMPORARY SCREWS
TO THE JOIST SIDE OF THE PANEL, THEN
USING SIPS SCREWS FIX FROM THE
OPPOSING SIDE OF THE PANEL,
STAGGARED AT 300mm C/C
JOISTS HANGER AND JOIST

SPACING STRICTLY TO JOIST
MANUFACTURERS OR TIMBER
CODE GUIDELINES

D
DTL No: REV
Intermediate Floor Section - Typical
IF EXTERNAL WALL
PROCTOR WALL WRAP
BREATHABLE MEMBRANE
EXTENAL WALL PANEL
BATTEN/CAVITY
PLASTERBOARD SELECTED CLADDING

(if applicable)
Dashed indicates
Alternative Joist FIRST FLOOR SIPS SOLE PLATE IS TO
Direction / Span BE NAIL FIXED AT 300mm C/C AND
COACH SCREWED ATJOIST CENTERS,
OR 900mm C/C ALONG PARALLEL
RUNNING JOISTS, ALTERNATIVELY
APPLY 3.5x45mm PGI STRAPPING WITH
4no 12g SCREW FIXINGS TO UPPER
AND LOWER PANEL AT EACH PANEL
JOINT.
FIX LVL OR TIMBER PERIMETER JOISTS

TO SIPS PANEL WITH 65mm NAILS AT
JOIST SPACING STRICTLY TO 150mm C/C. SMART JOISTS ARE TOE
ENGINEERS SPECIFICATION NAILED WITH 2/65mm RING SHANKS,
APPLY 1 NAIL AT 150mm C/C ALONG
JOISTS RUNNING PARALLEL TO SIPS
WALL.

D
DTL No: REV
LVL Beam Detail
OSB Facing
SIPS Panel supplied by
SIPS
LAMINATED
LVL BEAMS
300
265
33
115 145 Timber Packing
GLUE JOINT BETWEEN JOISTS
NAIL at 200mm C/C HORIZONTALLY

BOTH SIDES ALTERNATIVELY
NAIL 70mm FROM TOP AND BOTTOM

OF LVL BEAMS
NAIL LAMINATION
m
0m
20 SECTION SIZE 'B' NAIL DIA NAIL LENGTH
35mm 3.06mm 75mm
B 45mm 3.3mm 90mm
63mm 3.3mm 100mm

D
DTL No: REV
WINDOW DETAIL - Polar Window with CS Sheeting
10mm PLASTERBOARD
BREATHER MEMBRANE
145mm SIPS INDUSTRIES PANEL EXTERNAL CLADDING MATERIAL
AIR-TIGHT TAPE
120x35 MGP10 35mm EXERNAL BATTENS
POLAR DOUBLE GLAZING PROFILE
INTERNAL SIPS AIR-TIGHT SEALANT TAPE

SILL
* SIPS INDUSTRIES PANELS WILL ACCEPT ALMOST ANY WINDOW AND MAY NEED
PROJECT SPECIFIC DETAILING BY THE DESIGNER - WIINDOWS SHOWN ARE INDICITIVE ONLY

D
DTL No: REV
WINDOW DETAIL- Polar Window with Weatherboard
MIN 30mm OVERLAP
30
10mm PLASTERBOARD
BREATHER MEMBRANE
145mm SIPS INDUSTRIES PANEL EXTERNAL CLADDING MATERIAL
AIR-TIGHT TAPE
120x35 MGP10 35mm EXERNAL BATTENS
66x30 H3 LOSP Pre-Primed

AND SECRET FIXED
POLAR DOUBLE
GLAZING PROFILE
INTERNAL SILL
5°
66x30 H3 LOSP Pre-Primed

AND SECRET FIXED
HORIZONTAL BATTEN
SIPS AIR-TIGHT SEALANT TAPE
145
SIPS PANEL
* SIPS INDUSTRIES PANELS WILL ACCEPT ALMOST ANY WINDOW AND MAY NEED
PROJECT SPECIFIC DETAILING BY THE DESIGNER - WIINDOWS SHOWN ARE INDICITIVE ONLY

D
DTL No: REV
BOX BEAM & WALL ASSEMBLY
SIPS BOX BEAM

.
DOUBLE OR TRIPLE
TIMBER ENDS
.
.
TOP PLATE
BOX BEAM BASE PLATE SIPS SPLINE
SIPS 'BOX BEAM' LINTELS .

[NAIL AT 60mm C/C AND FOR
600mm ALONG TOP PLATE]
TOP PLATE
.
CRIPPLE STUDS
. SINGLE OR DOUBLE
AS SPEC BY ENGINEER
.
WINDOW INFILL PANELS
BASE PLATE
SIPS SPLINE
.
SIPS SCREWS TO CORNER JUNCTION
BASE PLATE

D
DTL No: REV
BOX BEAM & WALL ASSEMBLED
TOP PLATE
BASE PLATE
WINDOW INFILL PANELS

.
SIPS SCREWS TO CORNER JUNCTION
BASE PLATE

D
DTL No: REV
Box Beam Assembly - Exploded View
Continuous Top Plate
35
105
Varies
35
Continuous Bottom Plate
70 70
Box Beam Assembly - Assembled
60mm c/c for 600mm

Varies
BB
Nailing at 60mm c/c
Verticle Stud
Nailing at 150 c/c
70

D
DTL No: REV
STUD TIE DOWN DETAIL TYPE #1
TIMBER STUD
SIPS INDUSTRIES WALL PANEL
TIMBER STUD
TIE DOWN STUD ENCLOSED WITHIN
PANEL
TIMBER BOTTOM PLATE ANCHORED TO

CONCRETE WITH M12 ANCHOR BOLTS
TO ENGINEERS SPEC, CHEMSET OR TRUBOLT.
SOLE PLATE
150 150
30x1.0 GALVANISED TIE DOWN STRAP
FIXED VIA 6/2.8Ømm GALV NAILS TO
BOTH SIDES, ONE STRAP PER STUD
STUD TIE DOWN DETAIL TYPE #2

TIMBER STUD
TIMBER STUD
O
SB
SIPS INDUSTRIES WALL PANEL
NAILING @ 60mm C/C
NAILING @ 60mm C/C

TIE DOWN STUD ENCLOSED WITHIN
PANEL
600
600
TIMBER BOTTOM PLATE ANCHORED TO

CONCRETE WITH M12 ANCHOR BOLTS
TO ENGINEERS SPEC, CHEMSET OR TRUBOLT.
SOLE PLATE
NAIL OSB LOCALLY @ 60mm C/C 75 75

UP TO 600mm HIGH AND 300mm
EACH SIDE TO SOLE PLATE 300 300
NAILING @ 60mm C/C

D
DTL No: REV
SIPS 60/60/60 BOUNDARY WALL
HB FULLER FIRESOUND
SEALANT TOP OF WALL
25mm PLASTERBOARD SCREWS

Fixings are to be spaced at nominal 300mm centers SIPS INDUSTRIES PANEL WALL
into the perimeter studs and 200mm into the vertical
butt joints, maintaining nominal 12-15mm spacing BUILD TO MANUFACTURERS SPECIFICATIONS
from the board edge. The spacing in the field of the
sheets is to be 300mm.
SELECTED CEMENT SHEET
41mm PLASTERBOARD SCREWS CLADDING AS PER DRAWINGS
Fixings are to be spaced at nominal 300mm centers
into the perimeter studs and 200mm into the vertical AND/OR WORKS SPECIFICATION
butt joints, maintaining nominal 12-15mm spacing
sheets is to be 300mm. 16mm CSR FYRCHECK PLASTERBOARD
19mm NON-COMBUSTABLE BATTENING

145 78
JOINTING COMPOUND
CSR Gyprock Basecoat 45 or equivalent approved.
Nominal 50mm wide perforated tape along joints
on the outer layer of plasterboard
SEALANT PROCTOR WALL WRAP (RW)

HB FULLER FireSound Acryllic Sealant to be applied BREATHER MEMBRANE
to the perimeter plasterboard interface as detailed on VAPOUR BARRIER - WRAPED
ALL layers of Fyrcheck boards including any permitted AROUND BOTTOM ROOF BATTEN
services
16mm CSR FYRCHECK PLASTERBOARD

DAMP PROOF COURSE
PHYSICAL TERMITE BARRIER 13mm CSR FRYCHECK PLASTERBOARD
HB FULLER FIRESOUND
BOUNDARY
SEALANT
20

D
DTL No: REV
SIPS 60/60/60 BOUNDARY WALL GUTTER
NON-COMBUSTABLE ROOF FINISH
ROOF BATTEN / VENTED CAVITY
PROCTOR ROOFSHEILD
BREATHER MEMBRANE
VAPOUR BARRIER
DRESSED INTO GUTTER
SIPS SCREW FIXINGS AT 300mm C/C
STRATCO C-SQUARE GUTTER

OR SIMILAR APPROVED
DPC BEHIND GUTTER AND

DRESSED OVER FYRCHECK
SELECTED CEMENT SHEET

10mm PLASTERBOARD
CLADDING AS PER DRAWINGS
AND/OR WORKS SPECIFICATION
175 SIPS INDUSTRIES 66 79 NON-COMBUSTABLE BATTENING

ROOF PANEL SYSTEM - R4.4
PROCTOR WALL WRAP (RW)
BREATHER MEMBRANE
16mm CSR FYRCHECK
VAPOUR BARRIER - WRAPED
PLASTERBOARD
AROUND BOTTOM ROOF BATTEN
145mm SIPS 16mm CSR FYRCHECK PLASTERBOARD

13mm CSR FRYCHECK PLASTERBOARD
145 76
BOUNDARY
20

D
DTL No: REV
SIPS 60/60/60 PARTY WALL
338
BOUNDARY
HB FULLER FIRESOUND
SEALANT
25mm PLASTERBOARD SCREWS TOP OF WALL
butt joints, maintaining nominal 12-15mm spacing SIPS INDUSTRIES PANEL WALL
from the board edge. The spacing in the field of the BUILD TO MANUFACTURERS
sheets is to be 300mm. SPECIFICATIONS
40 or 50mm BUILDING GAP
50mm FIBREWOOL
ROXUL STONEWOOL or equivalent approved FIBRE WOOL INSULATION
insulation between SIPS wall with a density of MIN DENSITY 14kg/m³
14kg/m³ or greater for acoustic purposes
JOINTING COMPOUND
CSR Gyprock BAsecoat 45 or equivalent approved.
Nominal 50mm wide perforated tag along joints
SEALANT
HB FULLER FireSound Acryllic Sealant to be applied
to the perimeter plasterboard interface as detailed on
ALL layers of Fyrcheck boards.
16mm CSR FYRCHECK

PLASTERBOARD
13mm CSR FRYCHECK

PLASTERBOARD
HB FULLER FIRESOUND
SEALANT
ACOUSTIC
THIS WALL SYSTEMS HAS BEEN TESTED IN ACCORDANCE WITH AS1191 -
REPORT REF ALA-12-089-2, RESULTING IN AN ACOUSTING RATING OF: Rw64(-2-7)

D
DTL No: REV
SIPS 90/90/90 PARTY WALL
414
BOUNDARY
HB FULLER FIRESOUND
SEALANT
25mm PLASTERBOARD SCREWS TOP OF WALL
butt joints, maintaining nominal 12-15mm spacing SIPS INDUSTRIES PANEL WALL
from the board edge. The spacing in the field of the BUILD TO MANUFACTURERS
sheets is to be 300mm. SPECIFICATIONS
TOP HATS
40 or 50mm BUILDING GAP
Installed between the plasterboard layers as detailed. FIBRE WOOL INSULATION
Fixed at 600mm centers vertically. MIN DENSITY 14kg/m³
50mm FIBREWOOL
ROXUL STONEWOOL or equivalent approved
insulation between SIPS wall with a density of
14kg/m³ or greater for acoustic purposes
25mm FIBREWOOL
ROXUL STONEWOOL or equivalent approved
insulation between top hats with a density of
14kg/m³ or greater for its fire retartant properties
JOINTING COMPOUND
CSR Gyprock BAsecoat 45 or equivalent approved.
Nominal 50mm wide perforated tag along joints
16mm CSR FYRCHECK
SEALANT PLASTERBOARD
HB FULLER FireSound Acryllic Sealant to be applied
to the perimeter plasterboard interface as detailed on
ALL layers of Fyrcheck boards.
13mm CSR FRYCHECK
PLASTERBOARD
HB FULLER FIRESOUND
SEALANT

D
DTL No: REV
WINDOW MEMBRANE & TAPE INSTALL
THIS DETAIL IS FOR A WINDOW WITH A FIN TO PANEL CONNECTION (NOT A RECESSED WINDOW) ADN IS A WATER-
PROOFING DETAIL ONLY, THIS MAY NOT PROVIDE A FULLY AIR-TIGHT DETAIL. SUCH DETAILS ARE OFTEN PROJECT
SPECIFIC - THESE ARE TYPICAL DETAILS ONLAY AND ARE FOR REFERENCE PURPOSES FOR THE DESIGNER.
Cut Membrane Fold 'wings'

up 150mm into Reveal
Window Opening
UT
C
Primary Tape
OR Profiled Sill
. .
Cut Horizontally Secondary Sill Tape
to fit secondary tape
1.CUT MEMBRANE AS SHOWN 2.DRESS MEMBRANE INTO REVEAL 4.INSTALL WINDOW WITH SILL
3.APPLY SECONDARY SILL TAPE 5.IF NO SILL, APPLY PRIMARY TAPE
Dress Membrane
Over Flashing
TOP TAPE
Vertical Tape
Over SIll Tape DPC Lapped Under
Membrane by 150mm
6.APPLY VERTICAL SEALANT TAPES 7.APPLY TOP SEALANT TAPE 9.FOLD MEMBRANE DOWN
8.DRESS DPC BEHIND MAMBRANE
Tape Membrane Cut Air Movement
10.TAPE MEMBRANE OVER DPC 11.INSTALL BATTENS 12.INSTALL CLADDING
FIND THE OPENING CAREFULLY AND FIT SECONDARY WINDOW SILL APPLY PRIMARY TAPES, BEGINNING
CUT AN INVERTED 'Y' INTO THE MEMBRANE TAPE OR SIMILAR TRAY AT THE SILL OF THE WINDOW, THEN
VERTICALLY, AND FINALLY APPLYING
THE HEAD DETAIL AS ABOVE.

D
DTL No: REV
VENTILATED CAVITY
A VENTILATED CAVITY IS IMPORTANT TO CREATE AN AIRFLOW BETWEEN THE BREATHER MEMBRANE

SURROUNDING THE STRUCTURE AND THE CLADDING. ANY MOISTURE WITHIN THE STRUCTURE WILL BE
PULLED INTO THE VENTILATED SPACE THROUGH THE VAPOUR PERMEABLE MEMBRANE. THE AIR MOVEMENT
ALLWS THE VAPOUR TO EXPELL TO THE OUTDOORS ENSURING A DRY BUILDING WITH NO CHANCE OF MOISTURE
BUILD UP BEHIND CLADDINGS AND IN FRAMEING CASUNG MOULD, ROT, ALSO OTHERWISE KNOWN AS
'LEAKY' OR 'SICK BUILDING SYNDROME'.
REFER TO PREVIOUS DETAIL

FOR WINDOW SEALING OPTION
THE BOTTOM BATTEN IS DRILLED THROUGH

AND WRAPPED IN INSECT PROOF MESH THUS
CREATING AIR FLOW FROM THE BASE.
ALLOWING GAPS BETWEEN THE WALL BATTENS WILL

PERMIT THE AIR TO MOVE FREELY ACROSS THE ENTIRE
WALL AND NOT JCUST RESTRICTED TO A 'COMPARTMENT'.
ALLOWING FOR A VENT AT THE TOP OF THE CLADDING,

BEIT INTO THE ROOF SPACE, BEHIND THE FASCIA AND
OR SOFFIT OR AS DESIGNED IN BY THE DESIGNER, IS
ALSO IMPORTANT AS WARM MOIST AIR RISES.
THE IMAGE ON THE RIGHT DISPLAYS HOW THE BATTEN

HAS BEEN DRILLED AND SURROUNDED WITH INSECT
PROOF MESH, AND TAPED TO STOP INSECTS ACCESSING
FROM THE SIDES

D
DTL No: REV
SIPS EAVES DETAIL -PLUMB CUT ROOF

UNLESS OTHERWISE SPECIFIED BY
PROJECT ENGINEER
SELECTED ROOF CLADDING
ON SELECTED BATTENS
PROVIDE 10mm SHIMS BENEATH
HORIZONTAL BATTENS TO ALLOW
FOR MOISTURE FLOW
SIPS INDUSTRIES PROVIDED

BREATHABLE MEMBRANE.
LAPS OF AT LEAST 150mm.
TAPED LAPS FOR LOW PITCH
ROOFS, LAP MEMBRANE INTO GUTTER
SELECTED GUTTER
AND FASCIA BOARD/PROFILE
SIPS INDUSTRIES ROOF PANEL

GENERALLY 175mm THICK R4.4
SEE TECHNICAL SPECIFICATIONS
FOR SPANS AND OTHER INFORMATION
SELECTED SOFFIT LINING DORECT
TO PANEL OR TRADITIONAL ALTERNATIVE
SHOWN DASHED
SIPS INDUSTRIES EXTERNAL WALL PANEL

WITH BREATHER MEMBRANE, VERTICAL
BATTENS AND SELECTED CLADDING.
PROVIDE CAVITY VENTILATION PER
SIPS INDUSTRIES SPECIFICATIONS

D
DTL No: REV
SIPS EAVES DETAIL -SQUARE CUT ROOF

PROJECT ENGINEER
ON SELECTED BATTENS
FOR MOISTURE FLOW

SELECTED GUTTER
SHOWN DASHED


D
DTL No: REV
SIPS SKILLION DETAIL - PLUMB CUT
COLORBOND PROFILE CAPPING

PROJECT ENGINEER
ON SELECTED BATTENS
FOR MOISTURE FLOW

SELECTED
SOFFIT
LINING SIPS INDUSTRIES ROOF PANEL


D
DTL No: REV
SIPS EAVES DETAIL -CONCEALED GUTTER

ON SELECTED BATTENS
FOR MOISTURE FLOW

SELECTED GUTTER
TOP OF WALL FLASHED INTO

CAVITY OVER BREATHER MEMBRANE

PROJECT ENGINEER



D
DTL No: REV
SIPS EAVES DETAIL -SIPS CEILING


ON SELECTED BATTENS
SARKING OVER RAFTERS

USE TILTING FILLET TO SUPPORT SARKING
SELECTED GUTTER
TIMBER RAFTER WITH BIRDSMOUTH OVER
WALL PLATE, OR OVER PANEL END
SHOWN DASHED

PROJECT ENGINEER


D
DTL No: REV
SIPS EAVES DETAIL -SIPS CEILING -FLUSH
GUTTER


ON SELECTED BATTENS

USE TILTING FILLET TO SUPPORT SARKING
SELECTED GUTTER
PROVIDE PROFILED FLASHING BEHIND
GUTTER OVER EXTERNAL WALL AND
BREATEHR MEMBRANE
TIMBER RAFTER SKEW NAILED OR PRYDA

TRIPLE GRIP TO WALL PLATE WHICH IS
BUGLE FIXED TO SIPS PANEL AND
TOP PLATE OF WALL PANELS

PROJECT ENGINEER

D
DTL No: REV
SIPS EAVES DETAIL - EXTENDED SPLINE

PROJECT ENGINEER
ON SELECTED BATTENS
FOR MOISTURE FLOW

EXTENDED LVL SPLINE @MAX 1200 c/c

FOR FURTHER DETAILING BY BUILDER
SHOWN DASHED


D
DTL No: REV
SIPS SKILLION DETAIL - EXTENDED SPLINE
EXTENDED LVL SPLINES AT MAX 1200c/c

FOR FURTHER DETAILING BY BUILDER
COLORBOND PROFILE CAPPING

PROJECT ENGINEER

ON SELECTED BATTENS
FOR MOISTURE FLOW

SELECTED
SOFFIT
LINING SIPS INDUSTRIES ROOF PANEL


D
DTL No: REV
EAVES DETAIL - Framed Roof

ON SELECTED BATTENS

USE TILTING FILLET TO
SUPPORT SARKING
SELECTED GUTTER
TIMBER RAFTER WITH BIRDSMOUTH OVER

WALL PLATE, OR OVER PANEL END

SHOWN DASHED


D
DTL No: REV
RIDGE DETAIL - TYPICAL
Representative
Roof finish
SIPS Screws Staggared

@ 150 c/c
Breather Membrane
175/165 SIPS Roof Panels
Ridge Beam, LVL or Steel

to engineers detail
10mm Packers, or counter battens
allow moisture to pass.
RIDGE DETAIL - HIDDEN RIDGE

Representative
Roof finish
SIPS Screws Staggered

@ 150 c/c
Breather Membrane
175/165 SIPS Roof Panels
Ridge Beam, LVL or Steel

to engineers detail
FOR EASE OF CONSTRUCTION -
10mm Packers, or counter battens TEMPORARILY FIX A TIMBER
LENGTH TO THE UNDERSIDE
allow moisture to pass. OF THE RIDGE BEAM TO REST
THE SIPS ROOF PANEL ON DURING
INSTALL.

D
DTL No: REV
VELUX DETAIL - FLAT ROOF (FCM)
VELUX FCM FLAT ROOF WINDOW

FCM 2234 ( 572x877mm) 140x35 UPSTANDING TIMBER
MINIMUM FLASHING DIMENSIONS PURPOSE-MADE FLASHING

MIN 100mm HIGH AND 200mm
UP THE ROOF
SELECTED ROOFING
SIPS INDUSTRIES 175mm 35mm ROOF BATTENS

ROOF PANELS - R4.4
200
100
VELUX FCM SKYLIGHT - FCM 2234

SKYLIGHTIT TO BE FLASHED WITH
PURPOSE-MADE FLASHING IN STRICT
ACCORDANCE WITH THE MANUFACTURERS
DETAILS AND GUIDELINES.

D
DTL No: REV
SIPS BARGE DETAIL - TYPICAL
ROOF FINISH PER WORKS

SPECIFICATINO AND ADDENDA
INSTALLED TO MANUFACTURERS
REQUIREMENTS OVER TIMBER BATTENS
INSTALLED TO ENGINEERS SPEC, OVER
10mm WATER EGRESS SHIMS AND
SIPS INDUSTRIES BREATHABLE MEMBRANE
PROFILED COLORBOND
METAL FLASHING
SIPS INDUSTRIES 175 R4.4

ROOF PANEL LINED WITH
PLASTERBOARD INTERNALLY
WALL CLADDING PER FINISHES

SELECTION AND INSTALLED TO
MANUFACTURERS REQUIREMENTS
OVER SIPS INDUSTRIES WALL SYSTEM
Detail Title Detail312 D312

D
DTL No: REV

SIPS INDUSTRIES - Typical Details - Rev D-Version 1

Uploaded by

Copyright:

Available Formats

SIPS INDUSTRIES - Typical Details - Rev D-Version 1

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

SIPS INDUSTRIES - Typical Details - Rev D-Version 1

Uploaded by

Copyright:

Available Formats

TYPICAL DETAILS

D01 DETAIL LIST D

Detail Title DETAIL LIST D01

Detail Title Introduction D100

Pull dimensions from inside Face of Set Out Plate

12 Ensure the Gap is maintained

120 Sole Plate

Edge of Slab/ Floor

SIPS BUGEL HEAD SCREW

Detail Title Detail 101 D101

Pull dimensions from inside Face of Set Out Plate

ENSURE SLAB EDGE IS CHECK ENGINEERING

Pull dimensions from inside Face of Set Out Plate

Pull dimensions from inside Face of Set Out Plate

ENSURE SLAB EDGE IS CHECK ENGINEERING

Detail Title Detail 102 D102

SIPS INDUSTRIES EXTENAL WALL PANEL

Set Sole Plates 12mm

Snap Chalk Line

Dynabolts min 100mm

BOLTS TO BE 900mm C/C

Detail Title Detail 103 D103

PROCTOR WALL WRAP

Detail Title Detail 104 D104

PROCTOR WALL WRAP

DAMP PROOF COURSE /

ENSURE SLAB EDGE IS

Detail Title Detail 105 D105

PROCTOR WALL WRAP

WET AREA SET DOWN

WHERE WET AREA STOPS.

ENSURE CONCRETE UPSTAND IS

Detail Title Detail 106 D106

Snap Chalk Line 12

Detail Title Detail 107 D107

PROCTOR WALL WRAP

SOLE PLATE FIXING TO EACH

JOISTS FIXED TO TOP PALTE

Detail Title Detail 108 D108

SIPS INDUSTRIES EXTENAL WALL PANEL

SET SOLE PLATES 12mm Sole Plate +12mm

SNAP CHALK LINE 12 See SIPs Fixing Schedule

SIPS INDUSTRIES FLOOR PANEL

SIPS FLOOR PANELS ARE TO BE

Detail Title Detail 109 D109

PROCTOR WALL WRAP

SEE SIPS FIXING

BEARER BEAM TO ENGINEERS

Detail Title Detail 110 D110

175 SIPS INDUSTRIES FLOOR PANEL

ADDITIONAL COUNTER BEARER SERVICE AREA

BEARER BEAM TO ENGINEERS

Detail Title Detail 111 D111

SIPS INDUSTRIES FLOOR PANEL

ADDITIONAL COUNTER BEARER

INSULATION AND SERVICE AREA

Detail Title Detail 112 D112

Panels Slide over

PRE-ASSEMBLED WALL Continuous Glue Line