Professional Documents
Culture Documents
Advac 03
Advac 03
7-1C
1 ABB IB 6.2.15.7-1C
November 2005
TABLE OF CONTENTS
FORWARD ................................................................................................................................................................ 3
MAINTENANCE ...................................................................................................................................................... 16
Mechanism ................................................................................................................................................. 16
Truck ........................................................................................................................................................... 18
Control Wiring ............................................................................................................................................. 19
Primary Circuit ............................................................................................................................................ 19
APPENDICES ......................................................................................................................................................... 25
Appendix A: Basic Breaker Layout ............................................................................................................. 25
Appendix B: Basic Breaker Dimensions and Weights ............................................................................... 26
Appendix C: Close/Open Coil Data ........................................................................................................... 29
Appendix D: Wiring Diagrams ................................................................................................................... 30
Appendix E: Circuit Breaker Renewal Parts .............................................................................................. 32
3 ABB IB 6.2.15.7-1C
FORWARD
This booklet provides information for the ADVAC breakers as described below. Not all sections of the bulletin apply
to all types of ADVAC circuit breakers. For example, the racking and interlock sections do not apply to the fixed
mount breaker styles. All information in this booklet was current at the time of printing.
DRAWOUT:
Removable circuit breaker unit. Intended for use in SafeGearTM, Advance, or abbreviated versions of these
switchgear designs. Contains all racking interlocks and racking features required by ANSI standards. Automatic
primary and secondary disconnects. Provides three operating positions: disconnect, test, and connect.. Meets all
applicable ANSI standards, C37.09, C37.04, C37.06.
FIXED-MOUNT:
Intended to be mounted as a stationary device. No racking related interlocks. Primary connections are hard bus.
Secondary wiring terminates in stripped wire leads to be connected to the user’s terminals.
RETROFIT:
Intended to be mounted as a stationary or drawout device. Connections for racking related interlocks are included.
Primary connections are hard bussed. Secondary wiring terminates in stripped wire leads to be connected to the
user’s terminals.
ABB IB 6.2.15.7-1C 4
INTRODUCTION & SAFE PRACTICES
INTRODUCTION:
The purpose of this manual is to provide instructions for unpacking, storage, installation, operation and maintenance
for the ADVAC™ vacuum circuit breakers. This manual should be carefully read and used as a guide during
installation, initial operation, and maintenance.
The specific ratings of each model circuit breaker are listed on the individual nameplates. The ADVAC™ breakers
are protective devices. As such, they are maximum rated devices. Therefore, they should not under any
circumstances be applied outside of their nameplate ratings.
WARNING
THE CIRCUIT BREAKERS DESCRIBED IN THIS BOOK ARE DESIGNED AND TESTED
TO OPERATE WITHIN THEIR NAMEPLATE RATINGS. OPERATION OUTSIDE OF
THESE RATINGS MAY CAUSE EQUIPMENT TO FAIL, RESULTING IN PROPERTY
DAMAGE, BODILY INJURY AND DEATH.
ALL SAFETY CODES, SAFETY STANDARDS AND/OR REGULATIONS AS THEY MAY
BE APPLIED TO THIS TYPE OF EQUIPMENT MUST BE STRICTLY ADHERED TO.
SAFE PRACTICES:
ADVAC™ circuit breakers are equipped with high energy/high speed mechanisms. The design includes several
interlocks and safety features which help ensure safe and proper operating sequences. To ensure safety of
personnel associated with installation, operation and maintenance of these breakers, the following recommendations
must be followed:
Only qualified persons, as defined in the National Electric Safety Code, who are familiar with the installation and
maintenance of medium voltage circuits and equipment should be permitted to work on these breakers.
Read these instructions carefully before attempting any installation, operation or maintenance of these breakers.
DO NOT work on an energized breaker.
DO NOT work on a breaker unless all components are disconnected by means of a visible break and securely
grounded.
DO NOT work on a breaker with power supplied to the secondary control circuit.
DO NOT defeat safety interlocks. This may result in bodily injury, death and/or equipment damage.
DO NOT work on a closed breaker.
DO NOT work on a breaker with a charged closing spring.
DO NOT use a circuit breaker by itself as the sole means of isolating a high voltage circuit.
DO NOT leave a breaker in an intermediate position in a cell. Always place the breaker in the disconnect, test or
connected position.
NOTICE
FAILURE TO OBSERVE THE REQUIREMENTS OF OSHA STANDARD 1910.269 CAN
CAUSE DEATH OR SEVERE BURNS AND DISFIGUREMENT. THAT STANDARD
SPECIFICALLY PROHIBITS THE WEARING OF POLYESTER, ACETATE, NYLON, OR
RAYON CLOTHING BY EMPLOYEES WORKING WITH EXPOSURE TO ELECTRIC
ARCS OR FLAMES.
5 ABB IB 6.2.15.7-1C
RECEIVING:
Immediately upon receipt of the circuit breakers, examine the cartons to determine if any damage or loss was
sustained during transit. If damage or indication of rough handling is evident, file a damage claim at once with the
carrier and promptly notify the nearest District Office. ABB is not responsible for damage of goods after delivery to the
carrier. However, ABB will lend assistance if notified of claims. Use care in unpacking to avoid damaging any circuit
breaker parts.
Unpack circuit breakers as soon as possible after receipt. If unpacking is delayed, difficulty may be experienced in
making a claim for damages not evident upon receipt. Check the contents of each carton against the packing list
before discarding any packing material. If any discrepancy is discovered, promptly notify the nearest District Office.
Information specifying the purchase order number, carton number and part numbers of damaged or missing parts
should accompany the claim.
HANDLING:
ADVAC™ circuit breaker shipping containers are designed to be handled by a fork lift.
Once removed from the shipping container, the circuit breaker wheels are designed to move the breaker across a
smooth, paved surface.
Care must be taken not to damage the secondary locking tab (item 6, page Fig.5) when transporting, rolling, or
handling the ADVAC™ breakers.
DO NOT pull the circuit breaker by the front handles with the breaker in any position other than full disconnect.
STORAGE:
Circuit breakers should be installed in their permanent location as soon as possible. If the breakers are not placed in
service for some time, it is advisable to provide adequate means of environmental protection. This may be done by
keeping the breaker in its original shipping container and storing in a warm, dry and uncontaminated atmosphere.
The breakers should be stored to minimize condensation. Moisture can cause deterioration of metal parts and high
voltage insulation.
Prior to storage of the breaker, verification should be made that the breaker is free from shipping damage and is in
satisfactory operating condition.
CAUTION
The shipping containers provided are not designed for stacking.
ABB IB 6.2.15.7-1C 6
INSERTION AND REMOVAL
INSERTION AND REMOVAL
This section describes the process for inserting the breaker into the disconnect position of the switchgear and the
removal of the circuit breaker from the disconnect position. Racking of the circuit breaker to and from the test and
disconnect position is covered in the following section. The following rules should always be observed when inserting
or removing the circuit breaker device from the switchgear compartment.
• DO NOT attempt to insert the circuit breaker into any circuit breaker compartment prior to inspection of the
breaker. Compare breaker nameplate rating with switchgear rating. Verify secondary voltages on the breaker
and in the circuit breaker compartment.
• DO NOT attempt to insert a closed circuit breaker.
• ALWAYS inspect breaker compartment to ensure that it is free of obstructions, tools, or other equipment.
DANGER
Position Indication POSITIVE LOCK & CELL DECAL POSITIVE LOCK & CELL DECAL POSITIVE LOCK & CELL DECAL
Notes:
A. Closed door racking is recommended between ALL positions.
F # Description
A COMPARTMENT SLOTS
B GROUND BAR
C INTERFERENCE
BLOCKING PLATE
D
D SECONDARY
B
E WHEEL RAILS
F SHUTTERS
Figure 1: Basic Cell
C
A
9 ABB IB 6.2.15.7-1C
29
9
14
26
13
11
28 8
DANGER
MODIFICATION TO INTERLOCKS CAN RESULT IN HAZARDOUS CONDITIONS TO
PERSONNEL AND EQUIPMENT. DO NOT OVERRIDE, BY-PASS OR ADJUST
INTERLOCKS.
INTERFERENCE BLOCKING: A code plate in the breaker compartment prevents underrated breakers from being
inserted into higher rated compartments. The code plate rating includes continuous current, interrupting current,
close and latch capability and maximum voltage. Breakers with the same or higher code plate rating can be inserted
into a compartment of equal or lower value.
POSITIVE POSITION FOR RACKING: The racking mechanism is blocked unless the interlock tabs are fully extended into
the compartment slots.
POSITIVE POSITION FOR REMOVAL: The handle release pin prevents withdrawing the breaker from the compartment by
blocking withdrawal of the locking tabs. The handle release pin blocks the handles unless the breaker is in the
Disconnect position.
CAUTION
THE CLOSING SPRING MAY BE MANUALLY RECHARGED IN THE DISCONNECT AND
WITHDRAWN POSITIONS. VERIFY THAT THE BREAKER IS OPEN AND THE CLOSING
SPRING IS DISCHARGED BEFORE REMOVING THE FRONT COVER.
AUTOMATIC SPRING DISCHARGE (ASD): This maintenance interlock discharges the closing spring and opens the
breaker. Activation of the ASD occurs when withdrawing the locking tabs in the Disconnect position.
POSITION INTERLOCKS: The Position Release Lever must be depressed in order to begin racking the breaker in any
direction from any positive position (Disconnect, Test, or Connect). The release lever is blocked from actuation when
the breaker is CLOSED. The ability to close the breaker is blocked unless the breaker is in one of the three positive
positions.
ABB IB 6.2.15.7-1C 12
MECHANISM AND OPERATION
MANUAL OPERATION:
(Refer to Table 2 & Appendix A)
The breaker can be operated manually or electrically. The manual Charging Handle is required for manual operation.
1. Inspect initial state of the breaker to determine the operations available (Refer to Table 1 and Fig.2)
a. Close/Open indicator (29)
b. Closing Spring Charged/Discharged Indicator (28)
Closing Spring Indicator (6) Mechanism (4) Operations Available Proceed to Step
Table 2: Operations
3. Close breaker using manual close push-button or by electrical signal to the rotary close coil (after close operation
the motor charges unless control power is removed)
a. Close coil rotates half shaft and closes breaker
• Close/Open Indicator changes to CLOSED
• Closing Spring Charged/Discharged Indicator changes to DISCHARGED
• Charging motor energizes
• Charge time approximately 8-10 seconds (at nominal voltage)
• Closing Spring Charged/Discharged Indicator shows CHARGED
b. Breaker ready to perform O-C-O operation
4. Open breaker using manual open push-button or by electrical signal to the rotary open coil
a. Open coil rotates half shaft and opens breaker
• Close/Open Indicator changes to OPEN
• Closing Spring Charged/Discharged Indicator remains CHARGED
b. Breaker ready to perform C-O operation
5. Breaker ready to continue operations returning to step 3 above until the source of the control power is deactivated.
Once control power is removed from the charging motor, the Closing Spring will not recharge after a close
operation.
ABB IB 6.2.15.7-1C 14
MECHANISM AND OPERATION
CONTROL SCHEME:
ADVAC™ circuit breakers are available with two control packages. The standard package (see Appendix D)
includes charge, close, and open functions, and 4a and 4b auxiliary contacts for customer use. The optional
package (see Appendix D) adds to the standard package 5a and 4b auxiliary contacts for customer use as well
as an optional second open coil and/or under voltage (UV) open/trip device if required. Refer to wiring diagrams
in Appendix D and Figure 3: Sequence of Operation.
1. Initial State
a. Closing Spring Discharged (33LSa Open/33LSb Closed)
b. Breaker Open (52a Open/52b Closed)
2. Upon available control power
a. Secondary engaged
b. Motor charges through 33LSb
3. Closing spring charged
a. 33LSa closes
b. 33LSb opens (removing control power to motor)
c. Breaker ready to close
4. Electrical control pulse sent to close circuit
a. Current energizes Close Coil 52X (Close Coil is not rated for continuous duty)
• Coil rotates half shaft and closes breaker
– 52a closes – 52b opens
• Coil de-energizes with release of signal and as 52b opens
b. Current energizes 52TC (Trip Coil is not rated for continuous duty)
• 52TCa closes
• 52TCb opens
c. Closing Spring Discharges
• 33LSa closes
• 33LSb opens
d. Closing Spring charges
• 33LSa closes
• 33LSb opens (removing control power to motor)
• Breaker ready to perform O-C-O operation
15 ABB IB 6.2.15.7-1C
Charged
Closing Spring
Discharged
Charged
Opening Spring
Discharged
Charged
Contact Spring
Discharged
ON
Closing Coil
OFF
ON
Open Coil
OFF
ON
Circuit Breaker
OFF
open circuit
DANGER
High Speed Mechanical Parts. Serious injury may occur.
Keep hands and tools clear of the mechanism during opening and
closing operations and anytime the closing or opening springs are
charged. Before maintenance verify Closing Spring indicator reads
“Discharged”. Opening springs are always charged when the circuit
breaker is closed.
17 ABB IB 6.2.15.7-1C
MAINTENANCE
L
N K
M
J
O
See Fig 4B H
below
P
A
B G
F
D
E
# DESCRIPTION # DESCRIPTION
A ROCKER ARM J AUXILIARY SWITCHES
B CAM K MOTOR LIMIT SWITCH
C MAIN SHAFT L CLOSE COIL
D CHARGING MOTOR M CLOSE PUSH BUTTON
E CLOSING SPRING N OPEN PUSH BUTTON
F SECONDARY WIRING O OPEN/CLOSE INDICATOR
G SHAFT SUPPORT BUSHING P ANTI-PUMP CIRCUIT BOARD
H AUXILIARY SHAFT
Lubricate working
surfaces.
4
3
5
To verify the integrity of the secondary insulation, perform the following low-frequency withstand voltage test:
1. Connect all pins from the secondary to a test wire
2. Connect test wire to the high potential lead of the test machine
3. Ground the breaker frame
4. Start machine with output potential at 0 (zero) VAC RMS.
5. Increase the potential to the required insulation test voltage (1125VAC RMS)
6. Hold for one minute
7. Reduce potential to 0 (zero) VAC and turn off machine
A successful withstand indicates satisfactory insulation strength of the secondary circuit. Failing insulation will not
sustain the voltage across the secondary. Replace the breaker control wiring if the insulation fails during low-
frequency withstand voltage testing.
Replace the front cover before operation. Verify the operation with 2-5 electrical operations in the Test position or
with a remote power supply.
DANGER
The internal shield of a vacuum interrupter can acquire an electric
charge which CAN BE retained even after the voltage is removed.
Discharge the mid-band ring with a grounding stick before
working on any part of the circuit breaker.
To verify the integrity of the primary insulation, perform the following low-frequency withstand voltage test:
1. Close the breaker (no control power supplied to breaker)
a. Connect the high potential lead to one pole
b. Ground the remaining poles and breaker frame Rated Max Dielectric Test
Voltage Value, 1 Minute
2. Start machine with output potential at 0 (zero) VAC. Dry AC rms
3. Increase the potential to the required voltage (see Table 2)
4. Hold for one minute 4.76kV 15kV
5. Decrease potential to 0 (zero) VAC and turn off machine 8.25kV 27kV
6. Repeat for the remaining poles
15kV 27kV
A successful withstand indicates satisfactory insulation strength Table 2: Primary Low-Frequency Withstand Test
of the primary circuit. Voltages
To verify the integrity of the vacuum interrupters perform the following low-frequency withstand voltage test:
1. Open the breaker (no control power supplied to breaker)
a. Connect the high potential lead to one terminal
b. Ground the remaining 5 terminals and breaker frame
2. Start machine with output potential at 0 (zero) VAC
3. Increase the potential to the required voltage (see Table 2)
4. Hold for one minute
5. Decrease potential to 0 (zero) and turn off machine
6. Repeat for the remaining 5 terminals
A successful withstand indicates satisfactory vacuum integrity.
Replace pole assemblies that fail to withstand the voltage across the open contacts, ( if flashover occurs).
Testing should be done with an AC source only. DC testing is not considered a valid test for vacuum integrity. If
DC is the only available option, the peak DC voltage should not exceed the corresponding AC RMS test voltage.
Additionally, a failure during DC testing should only be considered preliminary. Additional AC testing should be
completed before replacement of the pole is considered to be warranted. Testing with meggers or other similar
devices is not considered valid under any circumstances.
21 ABB IB 6.2.15.7-1C
G&T DEVICE
SIMPLE G&T DEVICE:
The G&T device is designed for use in grounding and/or testing a circuit. The device is a manual cable device. The
cables are used to provide a solid path to the main ground bus of the switchgear though the automatic ground of the
G&T device. The cables are manually attached to each lead of the upper or lower lead set with the bolts and nuts
provided.
Insertion and racking of the G&T Device is similar to the circuit breaker; however, there are only two positions:
Disconnect and Connect. No position release is required. The automatic ground on the device makes its connection
when the device is inserted into the cell in the Disconnect position. The ground remains in contact throughout the
racking process.
All standard safety practices should be adhered to when using this device. Typical operating instructions are
included on the labels located on the G&T device front panel. A copy of this label is shown on the next page.
3. THIS DEVICE IS DESIGNED FOR USE WITH ONLY ONE SET OF CABLES AT-
TACHED TO A TERMINAL SET AT ANY GIVEN TIME. EITHER THE UPPER TERMI-
NALS ARE GROUNDED THROUGH THEIR CABLE SET OR THE LOWER TERMI-
NALS ARE GROUNDED THROUGH THEIR CABLE SET.
When moving or inserting the G&T TYPICAL OPERATING PROCEDURE FOR GROUNDING THE CIRCUIT BREAKER:
device, avoid exerting pressure on the 1. DISCONNECT THE GROUND CABLES FROM ALL TERMINALS
polyglass barriers. Damage to the 2. SWING DOOR OVER THE DEVICE TERMINAL SET THAT IS NOT TO BE
GROUNDED.
barriers may reduce dielectric strength of
3. PADLOCK THE DOOR IN THIS POSITION.
the device.
4. INSTALL THE DEVICE IN THE SAFEGEAR COMPARTMENT.
6. RACK THE DEVICE TO THE FULLY CONNECT POSITION. THE DEVICE MUST BE
IN THE FULLY CONNECT POSITION. THE “CONNECT” LABEL MUST BE IN THE
APPROPRIATE POSITION TO ASSURE THAT THE DEVICE IS INSTALLED PROP-
ERLY.
11. WITH THE GROUNDED CABLES ATTACHED, CLOSE AND SECURE THE SAFE-
GEAR DOOR AND RACK THE DEVICE TO THE “CONNECT” POSITION.
12. WITH THE GROUND CABLES INSTALLED AND THE DEVICE RACKED TO THE
“CONNECT” POSITION, THE TERMINAL SET CONNECTED TO THE GROUND CA-
BLES IS GROUNDED TO THE SAFEGEAR GROUND BUS.
15011P00 4 WHEEL
15095P00 4 AXLE BUSHING
16965P00 4 BOLT
16979P00 4 LOCKNUT
14526G00 3 CABLE ASSEMBLY - LONG
14540G00 3 POLE ASSEMBLY - 1200/2000A CONTINUOUS CURRENT; (ALL SHORT CIRCUIT CURRENTS
TO 50KA); INCLUDES PRIMARY DISCONNECTS AND MOUNTING HARDWARE
14547G00 3 POLE ASSEMBLY - 3000A CONTINUOUS CURRENT; (ALL SHORT CIRCUIT CURRENTS TO
50KA); INCLUDES PRIMARY DISCONNECTS AND MOUNTING HARDWARE
706741T13 6 PRIMARY DISCONNECT (“FINGERS”); 1200/2000A, TO 50KA SHORT CIRCUIT
NOTE: The parts listed above are available from ABB for field use or replacement. Consult your ABB sales
representative for current pricing and availability.
23 ABB IB 6.2.15.7-1C
Insertion and racking of the Dummy Breaker Device is similar to the circuit breaker, however there are only two
positions; Disconnect and Connect. No position release is required. The automatic ground on the device makes
connection when the device is inserted into the cell in the Disconnect position. The ground remains in contact
throughout the racking process. The device MUST NOT be racked into or from the Connect position when the circuit
is energized. Verification that the circuit is de-energized must be made before racking the device.
Kirk Key interlocks are provided to lock the device in the Disconnect or Connect. These locks provide an added
measure of safety; however, ALL other safety procedures and verifications MUST be followed to avoid the possibility
of a fault during racking.
15011P00 4 WHEEL
15095P00 4 AXLE BUSHING
16965P00 4 BOLT
16979P00 4 LOCKNUT
14706G00 3 POLE ASSEMBLY - 1200/2000A CONTINUOUS CURRENT; (ALL SHORT CIRCUIT CURRENTS
TO 50KA); INCLUDES PRIMARY DISCONNECTS AND MOUNTING HARDWARE
14707G00 3 POLE ASSEMBLY - 3000A CONTINUOUS CURRENT; (ALL SHORT CIRCUIT CURRENTS TO
50KA); INCLUDES PRIMARY DISCONNECTS AND MOUNTING HARDWARE
706741T13 6 PRIMARY DISCONNECT (“FINGERS”); 1200/2000A, TO 50KA SHORT CIRCUIT
NOTE: The parts listed above are available from ABB for field use or replacement. Consult your ABB sales
representative for current pricing and availability.
ABB IB 6.2.15.7-1C 24
OPTIONAL ACCESSORIES
LIFTING HOOK:
The lifting hook is designed for general lifting and lowering of the device, such as for removal from shipping pallets or
for lifting onto and off of work tables. The lifting hook is not designed to be used for insertion or removal of the circuit
breaker from the switchgear compartment, instead, use the appropriate optional lift truck.
continuous duty)
CAUTION
• Always follow safe work practices when lifting the circuit
breakers to protect the safety of personnel and equipment.
• Always inspect lifting hook for signs of wear or damage before
use.
• Do not use a lifting hook that is damaged or worn.
• The lifting device (i.e. hoist, wench) should be suitably rated
for lifting the breaker load.
• Always refer to Fig 7 below for the proper installation of the
lifting hook.
The chain type lifting hook is designed to attach to the breaker in the lifting angles, (clips) on each side of the frame .
Chain hook:
Attach one lifting
hook to each side of
breaker on the
designated lifting
angle.
Remember to remove
the lifting angle
before energizing the
breaker
3
# Description
4
1 FRONT PLATE ASSEMBLY
16 5 2 CLOSE PUSH BUTTON
6 3 OPEN PUSH BUTTON
4 CLOSE/OPEN INDICATOR
5 CHARGING PAWL
10
6 CHARGED/DISCHARGED
11 INDICATOR
7 RACKING SCREW
8 8 COLLAR
7 9
9 POSITION RELEASE LEVER
10 HANDLE
13
750MM DRAWOUT
750 MM FIXED/RETROFIT-MOUNT R:
APPENDIX B
POLE ASSEMBLIES USED ON ADVAC
Assembled Pole
Embedded Pole P3 Embedded Pole P2
15kV 2000A 50 kA
15kV / 1200A / 25 - 40kA 15kV 2000A 25 - 40kA
15kV 3000A 40 & 50kA
CLOSE COILS
NOMINAL CONTROL VOLTAGE RANGE RESISTANCE
VOLTAGE OF RANGES (W)
BREAKER
FIXED-MOUNT/RETROFIT -
STANDARD WIRING:
The wiring scheme for the fixed-mount
breakers is exactly the same as that for the
drawout breakers. The only difference is
that the terminations ending in the
secondary disconnect plug on the drawout
breakers are provided as un-lugged wires
for connection to terminal strips.
DRAWOUT - OPTIONAL
WIRING:
The schematic shows the basic
wiring scheme for drawout breaker
with optional wiring. This wiring
includes nine “a” and eight “b”
auxiliary contacts.
FIXED-MOUNT/RETROFIT -
OPTIONAL WIRING:
The wiring scheme for the fixed-
mount breakers is exactly the same
as that for the drawout breakers.
The only difference is that the
terminations ending in the
secondary disconnect plug on the
drawout breakers are provided as
un-lugged wires for connection to
terminal strips.
ABB IB 6.2.15.7-1C 32
APPENDIX E
CIRCUIT BREAKER RENEWAL PARTS AND ACCESSORIES:
The parts listed below are available from ABB for field use or replacement. Consult your ABB sales representative
for current pricing and availability.
ACCESSORIES:
Part # Qty/Breaker Description
14020P00 1 CHARGING HANDLE
14024G00 1 RACKING HANDLE ASSEMBLY
14038G00 1 LIFTING HOOK ASSEMBLY (CHAIN)
961484 1 / SWITHGEAR BREAKER RELEASE MECHANISM (AVAILABLE FROM ABB, LAKE MARY)
LINE-UP
MECHANISM:
Part # Qty/Breaker Description
GCE0940084P0105 1 CHARGING MOTOR (120VAC/125VDC)
GCE0940084P0106 1 CHARGING MOTOR (240VAC/250VDC)
GCE0940084P0103 1 CHARGING MOTOR(48VDC)
11142G00 1 OPERATION COUNTER ASSEMBLY
16008G00 1 ADVAC LABEL KIT
16016G30 1 FRONT PLATE ASSEMBLY ( W/O RATING LABEL)
APPENDIX E
CIRCUIT BREAKER RENEWAL PARTS AND ACCESSORIES:
The parts listed below are available from ABB for field use or replacement. Consult your ABB sales representative
for current pricing and availability.
ELECTRICAL (CONTROL):
Part # Qty/Breaker Description
18081G00 1 STANDARD WIRING ASSEMBLY (“AA3” PREFIX CAT. #’S)
18084G00 1 OPTIONAL WIRING ASSEMBLY (ADDITIONAL AUX. CONTACTS)(“AA3” PREFIX CAT. #’S)
18005P10 2 AUX. SWITCH, 3a & 2b CONTACTS
18005P20 1 OR 3 AUX. SWITCH, 2a & 3b CONTACTS
GCE7004590P0105 1 CLOSE COIL, 125VDC
GCE7004590P0106 1 CLOSE COIL, 250VDC
GCE7004590P0103 1 CLOSE COIL, 48VDC
GCE7004590P0115 1 OPEN COIL, 125VDC
GCE7004590P0116 1 OPEN COIL, 250VDC
GCE7004590P0113 1 OPEN COIL, 48VDC
GCE7004590P0111 1 OPEN COIL, 24VDC
18069G10 1 UNDERVOLTAGE ASSEMBLY, 125VDC
18069G20 1 UNDERVOLTAGE ASSEMBLY, 250VDC
18069G30 1 UNDERVOLTAGE ASSEMBLY, 48VDC
18069G40 1 UNDERVOLTAGE ASSEMBLY, 120VAC
18069G50 1 UNDERVOLTAGE ASSEMBLY, 240VAC
GCE7004590P0105 1 2ND OPEN COIL ASSEMBLY, 125VDC
GCE7004590P0106 1 2ND OPEN COIL ASSEMBLY, 250VDC
GCE7004590P0103 1 2ND OPEN COIL ASSEMBLY, 48VDC
ABB Inc.
Circuit Breaker Technology Solutions
2300 Mechanicsville Highway
Florence, SC 29501
Toll free 1-877-SOS-CBTS or +1 (843) 413-4700
Fax +1 (843) 413-4850
www.abb.com/mediumvoltage