CF 19 Chbaxbm

ORDER NO.
CPD0611206C1
Notebook Computer
Model No. CF-19CHBAXBM
This is the Service Manual for

the following areas.
M …for U.S.A. and Canada
Model No. CF-19CHBAX 1 2

1: Operation System
B: Microsoft® Windows® XP Professional
2: Area
M: Refer to above area table
© 2006 Matsushita Electric Industrial Co., Ltd. All rights reserved.

Unauthorized copying and distribution is a violation of law.
Downloaded from www.Manualslib.com manuals search engine

Downloaded from www.Manualslib.com manuals search engine 1
CONTENTS
1. Specifications 1-1
2. Names and Functions of Parts 2-1
3. Block Diagram 3-1
4. Diagnosis Procedure 4-1
5. Power-On Self Test (Boot Check) 5-1
6. List of Error Codes <Only when the port replicator is connected> 6-1
7. Self Diagnosis Test 7-1
8. Wiring Connection Diagram 8-1
9. Disassembly/Reassembly 9-1
10. Exploded View 10-1
11. Replacement Parts List 11-1

1 Specifications
Main Specifications
Model No. CF-19CHBAXBM CF-19CDBAXVM
CPU Intel Core™ Duo Processor U2400 (1.06 GHz, 2 MB*1 L2 cache, 533 MHz FSB)
®
Chipset Intel® 945GM

*1*2
Memory 512 MB (4096 MB Max.)
Video Memory*1*3 UMA (128 MB Max.)
*4
Hard Disk Drive 80 GB
Display Method 10.4 XGA type (TFT)
*5
Internal LCD 65,536/16,777,216 colors (800 × 600 dots/1024 × 768 dots)
External Display*6 65,536/16,777,216 colors (800 × 600 dots/1024 × 768 dots/1280 × 768 dots/1280 × 1024
dots)
Wireless LAN*7 Intel PRO / Wirelee 3945 ABG (802.11a + b + g)
TM *8
Bluetooth 2.0 + EDR
LAN IEEE 802.3 10Base-T, IEEE 802.3u 100Base-TX
Modem Data: 56 kbps (V.92) FAX: 14.4 kbps
Sound WAVE and MIDI playback, Intel® High DeÞnition Audio subsystem support, Monaural speaker
Security Chip TPM (TCG V1.2 compliant)*9
Card Slot PC Card Type I or Type II x 1 (3.3 V: 400 mA, 5 V: 400 mA)
ExpressCard ExpressCard/34*10 or ExpressCard/54 x 1
*11
SD Memory Card x 1, Data transfer rate = 8 MB per second*12
RAM Module Slot 200-pin, 1.8 V, SO-DIMM, DDR2 SDRAM, PC2-4200 Compliant
Interface USB port (4-pin, USB 2.0) x 2, Serial Port (Dsub 9-pin male), Modem port (RJ-11), LAN port
(RJ-45), External display port (Mini Dsub 15-pin female), Expansion Bus Connector (Dedicated
100-pin female), External Antenna Connector (Dedicated 50 coaxial connector) x 2, IEEE
1394a Interface Connector (4-pin x 1), Microphone Jack (Miniature jack, 3.5 DIA, Stereo),
Headphone Jack (Miniature jack, 3.5 DIA, Impedance 32 , Output Power 4 mW × 2)
Keyboard / Pointing Device 82 keys / Touch Pad / Touchscreen (Anti- 82 keys / Touch Pad / Digitizer (Anti-Reßec-
Reßection, Stylus (included) touch capable) tion)
Power Supply AC adaptor or Battery pack
AC Adaptor*13 Input: 100 V to 240 V AC, 50 Hz/60 Hz, Output: 16.0 V DC, 3.75 A
Battery Pack Li-ion 10.65 V, 5.7 Ah
*14
Operating Time Approx. 4.5 hours to 8 hours*15 (Approx. 7 hours*16)
Charging Power on Approx. 7.5 hours
Time*14
Power off Approx. 4.5 hours
Clock Battery Coin type lithium battery 3.0 V
*17
Power Consumption Approx. 26 W*18 / Approx. 55 W (Maximum when recharging in the ON state)
Physical Dimensions (W × H × D) 271 mm × 49 mm × 216 mm {10.7" × 1.93" × 8.5"}
(excluding the hand strap/shoul-
der strap)
Weight Approx. 2.25 kg {Approx. 4.96 lb.} Approx. 2.30 kg {Approx. 5.07 lb.}
(excluding the hand strap/shoul-
der strap)
Operation Environment Temperature: 5 °C to 35 °C {41 °F to 95 °F}
Humidity: 30% to 80% RH (No condensation)
Storage Environment Temperature: -20 °C to 60 °C {-4 °F to 140 °F}
Humidity: 30% to 90% RH (No condensation)
Downloaded from www.Manualslib.com manuals search engine 1-1

Operating System Microsoft® Windows® XP Professional Service Microsoft® Windows® XP Tablet PC Edition
Pack 2 with Advanced Security Technologies 2005
(NTFS File System) (NTFS File System)
Utility Programs DMI Viewer, Microsoft® Windows® Media Player 10, Adobe Reader, PC Information Viewer,
SD Utility, Icon Enlarger, Loupe Utility, Intel® Matrix Storage Manager, Intel® PROSet/Wireless
Software*7, Bluetooth™ Stack for Windows® by TOSHIBA*8 , Wireless Switch Utility, Hotkey
Settings, Battery Recalibration Utility, Panasonic Hand Writing*19, Software Keyboard*19, Dis-
play Rotation Tool, InÞneon TPM Professional Package*20, Recover ProTM 6*20 , Tablet Buttons
Settings*19
Setup Utility, Hard Disk Data Erase Utility*21, PC-Diagnostic Utility
Wireless LAN <Only for model with wireless LAN>

Intel PRO / Wireless 3945 ABG (802.11 a + b + g)
Data Transfer Rates*22 IEEE802.11a: 54/48/36/24/18/12/9/6 Mbps (automatically switched)
IEEE802.11b: 11/5.5/2/1 Mbps (automatically switched)
IEEE802.11g: 54/48/36/24/18/12/9/6 Mbps (automatically switched)
Standards Supported IEEE802.11a/IEEE802.11b/IEEE802.11g
Transmission method OFDM system, DSSS system
Wireless Channels Used IEEE802.11a: Channels 36/40/44/48/52/56/60/64/149/153/157/161/165
IEEE802.11b/IEEE802.11g: Channels 1 to 11
RF Frequency Band IEEE802.11a: 5.18-5.32 GHz, 5.745-5.825 GHz
IEEE802.11b/IEEE802.11g: 2.412-2.462 GHz
BluetoothTM <Only for model with Bluetooth>

Bluetooth Version 2.0 + EDR
Transmission method FHSS system
Wireless Channels Used Channels 1 to 79
RF Frequency Band 2.402-2.48 GHz
Power Class Class1
*1
1 MB = 1,048,576 bytes
*2
You can physically expand the memory upto 4 GB, but the total amount of usable memory available will be less depending on
the actual system conÞguration.
*3
A segment of the main memory is allotted automatically depending on the computer’s operating status. The size of the Video
Memory cannot be set by the user.
*4
1 GB = 1,000,000,000 bytes. Your operating system or some application software will report as fewer GB.
*5
A 16,777,216 color display is achieved by using the dithering function.
*6
Maximum resolution depends on the speciÞcations of the external display.
*7
Only for model with wireless LAN
*8
Only for model with Bluetooth
*9
For information on TPM, click [start] - [Run] and input “c:\util\drivers\tpm\README.pdf”, and refer to the Installation Manual of
“Trusted Platform Module (TPM)”.
*10
When using ExpressCard/34, the card slot cover cannot be closed.
*11
Operation has been tested and conÞrmed using Panasonic SD Memory Cards with a capacity of up to 2 GB.
The transfer rate using the SD Memory Card slot on this computer is 8 MB per second. (This is a theoretical value, and differs
from actual speeds.)
The transfer rate is 8 MB per second even if you use an SD Memory Card that supports high-speed transfer rates.
Operation on other SD equipment is not guaranteed.
This computer is not compatible with MultiMediaCards or SDHC Memory Cards. Do not insert these kinds of cards.
*12
Theoretical value and not the actual speed. The transfer rate does not become higher even if you use a card that supports the
higher transfer rate.
*13
The AC adaptor is compatible with power sources up to 240 V AC adaptor. The computer is supplied with a 125 V AC compat-
ible AC cord. 20-M-2-1
*14
Varies depending on the usage conditions.
*15
Measured using BatteryMark™ Version 4.0.1 (LCD brightness: Maximum - Minimum)
*16
Measured using MobileMark™ 2005 (LCD brightness: 60 cd/m2)
*17
Approx. 26 W when the battery pack is fully charged (or not being charged) and the computer is OFF.
Approx. 1.2 W when the Wake up from LAN has been enabled.
*18
Rated power consumption 23-E-1
*19
Only for model with Windows XP Professional
*20
You need to install to use the feature.
*21
The Product Recovery DVD-ROM is required.
*22
These are speeds speciÞed in IEEE802.11a+b+g standards. Actual speeds may differ.

2 Names and Functions of Parts
A: Wireless LAN Antenna G: LCD

<Only for model with wireless LAN> <Only for model with touchscreen>
Reference Manual “Wireless LAN” Reference Manual “Touchscreen”
B: Bluetooth Antenna <Only for model with digitizer>
<Only for model with Bluetooth> Reference Manual “Digitizer”
Reference Manual “Bluetooth” H: Display Release Latch
C: Stylus/Pen Holder page 12 “Switching to the Tablet mode”
D: Touch Pad I: Speaker
E: LED Indicator
Reference Manual “Key Combinations”
: Wireless ready
This indicator lights when Wireless LAN, Blue- J: Function Key
tooth, and/or Wireless WAN are connected and Reference Manual “Key Combinations”
ready. It does not necessarily indicate the On/Off K: Keyboard
condition of the wireless connection. L: Hard Disk Drive
Reference Manual “Wireless Switch Utility” Reference Manual “Hard Disk Drive”
: Wireless WAN status M: Battery Pack
<Only for model with wireless WAN> N: Power Switch
Refer to the instruction manual of the wireless O: LED Indicator
device. : Battery status
: Caps lock Reference Manual “Battery Power”
: Numeric key (NumLk) : Power status
: Scroll lock (ScrLk) (Off: Power off/Hibernation, Green: Power on,
: Hard disk drive status Blinking green: Standby)
F: Tablet Buttons
Reference Manual “Tablet Buttons”
A lithium ion battery that is recyclable powers the product you have purchased.
Please call 1-800-8-BATTERY for information on how to recycle this battery.
L’appareil que vous vous êtes procuré est alimenté par une batterie au lithium-ion.
Pour des renseignements sur le recyclage de la batterie, veuillez composer le
1-800-8-BATTERY.

Left side
Rear side Bottom
A: DC-IN Jack L: Microphone Jack

B: USB Port A condenser microphone can be used. If other types
Reference Manual “USB Devices” of microphones are used, audio input may not be pos-
C: IEEE 1394 Interface Connector sible, or malfunctions may occur as a result.
Reference Manual “IEEE 1394 Devices” When recording in stereo using a stereo micro-
phone:
D: Modem Port Double-click in the notiÞcation area, click [Op-
Reference Manual “Modem” tions] - [Properties], and add a check mark for [Re-
E: LAN Port cording], click [OK] - [Options] - [Advanced Controls]
- [Advanced], remove a check mark for [Mono Micro-
Reference Manual “LAN”
phone], and then click [Close].
F: SD Memory Card Indicator When using a monaural microphone with a 2-termi-
(Blinking: During access) nal plug:
Reference Manual “SD Memory Card” With the settings outlined above, only audio on the
left track will be recorded.
G: SD Memory Card Slot
When monitoring the microphone audio using head-
Reference Manual “SD Memory Card” phones, sounds on the left track cannot be heard,
H: Wireless Switch regardless of the above settings. This is a result of the
Reference Manual “Wireless Switch Utility” computer’s speciÞcations, and is not a malfunction.
I: PC Card Slot M: Security Lock
A Kensington cable can be connected.
Reference Manual “PC Card / ExpressCard”
For further information, read the manual that comes
J: ExpressCard Slot
with the cable.
Reference Manual “PC Card / ExpressCard” N: External Display Port
K: Headphone Jack Reference Manual “External Display”
You can connect headphones or ampliÞed speakers.
O: Serial Port
When they are connected, audio from the internal
P: RAM Module Slot
speakers is not heard.
Reference Manual “RAM Module”
Q: Expansion Bus Connector
Reference Manual “Port Replicator / Car Mounter”
R: External Antenna Connector

4 Diagnosis Procedure
4.1. Basic Procedures

4.2. Troubleshooting
Please take note of the following two points with regard to troubleshooting:
1. Know-how of diagnosis upon occurrence of heavy troubles, e.g. Set cannot be turned ON , Set fails to start , No display on
screen , etc.
2. Explanation of each trouble, mainly symptom of trouble in operation.
Flow Chart Pay attention to the following points when in pursuit of the cause of a troubleshooting.
1. Peripheral apparatus connected with the set should all be removed before operation check.
START
START 2. Make sure that cables, boards, etc. are not coming off, and recheck the contact condition.
Set cannot be supplied with current. AC NG

Adaptor/Battery Replace AC Adaptor/Battery
Power lamp fails to light up. Output voltage
OK
NO Check contact condition of power input terminal. Replace if
Power lamp
check defective.
YES Check Power SW. Replace if defective.
Dark display on screen. NG Replace inverter board.

Inverter board
Screen fails to display. Check inverter cable continuity. Replace if defective
OK
LCD back NO Replace LCD back light.

light lighting
YES
LCD unit
NG
Replace LCD unit.
check
OK
BIOS operation NO Replace main board (Check fuse at power source).

Failure in starting
check
YES
Result of NG Refer to POST Replace main board.

POST error code table.
OK
Set-up utility NG Replace main board. Heavy trouble e.g.,

starting Set cannot be turned
ON , Set fails to start ,
OK No display on
Return set-up utility setpoint to the state of delivery from factory . screen , etc.
Check HDD cable connection and continuity.

NO
HDD access Replace if defective.
Replace HDD & Reinstall.
YES Replace main board.
Main board
NG
Not displayed properly on screen. Replace main board
check
OK
Some or all keys cannot be input. Make sure of contact of K/B connector in use. Each kind of
Replace keyboard or main board. trouble in
operation.
Trouble NO Check if there are any flaws on CD media. Since
CD CALL not practicable. symptoms on some flaws may appear on specific media, CD media
of CD
can be defective.
YES
Replace main board.
Starts but operates unstably. Reinstall HDD.

Replace main board.
START
END

5 Power-On Self Test (Boot Check)
Outline of POST
The set has a boot check function called POST (Power-On Self Test) in it.
The condition of the main body is diagnosed by checking beep sound or error code.
Start .............Test begins automatically when power switch is set to ON.
Normal finish .....After memory checking, a beep sound is issued once and the set is placed into automatic stop.
Note: If no error occurs, nothing is displayed. (No display of OK, etc.)
Error Diagnosis by Checking Beep Signal Sound

The beep sound is as follows:
(1 (long sound) -2-3-4)

(Length of bar shows length of sound.)
= long sound (about 0.4 sec.), = short sound (about 0.2 sec.), Length between sounds is about 0.1 sec.
Table of errors classified by beep sounds
Diagnosis Beep signal sound Error message

Main board 1(long sound)-2 BIOS ROM error
1-2-2-3 BIOS ROM error
1-3-1-1 RAM error
1-3-1-3 Keyboard controller error
1-3-4-1 RAM error
1-3-4-3 RAM error
1-4-1-1 RAM error
2-1-2-3 BIOS ROM error
2-2-3-1 Occurrence of unexpected offering
(Note) A beep sound is also issued in case of other I/O trouble.

6 List of Error Codes <Only when the port replicator is connected>
The following is a list of the messages that BIOS can display. Most of them occur during
POST. Some of them display information about a hardware device, e.g., the amount of memory
installed. Others may indicate a problem with a device, such as the way it has been configured.
Following the list are explanations of the messages and remedies for reported problems.
If your system displays one of except the messages marked below with an asterisk (*), write
down the message and contact Panasonic Technical Support. If your system fails after you
make changes in the Setup menus, reset the computer, enter Setup and install Setup defaults
or correct the error.
0200 Failure Fixed Disk

Fixed disk in not working or not configured properly. Check to see if fixed disk is attached
properly. Run Setup. Find out if the fixed-disk type is correctly identified.
0210 Stuck key
Stuck key on keyboard.
0211 Keyboard error
Keyboard not working.
0212 Keyboard Controller Failed
Keyboard controller failed test. May require replacing keyboard controller.
0213 Keyboard locked - Unlock key switch
Unlock the system to proceed.
0230 System RAM Failed at offset : nnnn
System RAM failed at offset nnnn of in the 64k block at which the error was detected.
0231 Shadow RAM Failed at offset : nnnn
Shadow RAM failed at offset nnnn of the 64k block at which the error was detected.
0232 Extended RAM Failed at offset : nnnn
Extended memory not working or not configured properly at offset nnnn.
0250 System battery is dead - Replace and run SETUP
The CMOS clock battery indicator shows the battery is dead. Replace the battery and run Setup
to reconfigure the system.
*0251 System CMOS checksum bad - Default configuration used
System CMOS has been corrupted or modified incorrectly, perhaps by an application program
that changes data stored in CMOS. The BIOS installed Default SETUP Values. If you do not
want these values, enter Setup and enter your own values. If the error persists, check the system
battery or contact Panasonic Technical Support.
0260 System timer error
The timer test failed. Requires repair of system board.
0270 Real time clock error
Real-time clock fails BIOS test. May require board repair.
*0280 Previous boot incomplete - Default configuration used
Previous POST did not complete successfully. POST loads default values and offers to run
Setup. If the failure was caused by incorrect values and they are not corrected, the next boot
will likely fail. On systems with control of wait states, improper Setup settings can also termi-
nate POST and cause this error on the next boot. Run Setup and verify that the wait-state
configuration is correct. This error is cleared the next time the system is booted.
0281 Memory Size found by POST differed from EISA CMOS
Memory size found by POST differed from EISA CMOS.

02D0 System cache error - Cache disabled
Contact Panasonic Technical Support.
02F0: CPU ID:
CPU socket number for Multi-Processor error.
02F4: EISA CMOS not writable
ServerBIOS2 test error: Cannot write to EISA CMOS.
02F5: DMA Test Failed
ServerBIOS2 test error: Cannot write to extended DMA (Direct Memory Access) registers.
02F6: Software NMI Failed
ServerBIOS2 test error: Cannot generate software NMI (Non-Maskable Interrupt).
02F7: Fail - Safe Timer NMI Failed
ServerBIOS2 test error: Fail-Safe Timer takes too long.
device address Conflict
Address conflict for specified device.
Allocation Error for: device
Run ISA or EISA Configuration Utility to resolve resource conflict for the specified device.
Failing Bits : nnnn
The hex number nnnn is a map of the bits at the RAM address which failed the memory test.
Each 1 (one) in the map indicates a failed bit. See error 230,231 or 232 for offset address of the
failure in System, Extended or Shadow memory.
Invalid System Configuration Data
Problem with NVRAM (CMOS) data.
I/O device IRQ conflict
I/O device IRQ conflict error.
Operating System not found
Operating system cannot be located on either drive A: or drive C:. Enter Setup and see if fixed
disk and drive A: are properly identified.
Parity Check 1 nnnn
Troubleshooting
Parity error found in the system bus. BIOS attempts to locate the address and display it on the
screen. If it cannot locate the address, it displays ????. Parity is a method for checking errors
in binary data. A parity error indicates that some data has been corrupted.
Parity Check 2 nnnn
Parity error found in the I/O bus. BIOS attempts to locate the address and display it on the
screen. If it cannot locate the address, it displays ????.
Press <F1> to resume, <F2> to Setup
Displayed after any recoverable error message. Press <F1> to start the boot process or <F2> to
enter a Setup and change the settings. Write down and follow the information shown on the
screen.

7 Self Diagnosis Test
As for the self-diagnosis test(PC-Diagnostic utility) to use this model, a standard test and the
enhancing test by the module of the main body building in are possible.
Notes To skip BIOS password
Use <Ctrl>+<F10> key to skip BIOS password or authentication of fingerprint.
This key is only for entering DIAG mode. Not available to boot the computer.
If customer set "HDD Lock", the DIAG program cannot perform HDD test.
*This key is for service purpose only. Do not disclose this information to unrelated others.
1. Beginning of self-diagnosis test
1-1. Setting of content of setup
1. The power supply of the computer is turned on.
2. " F2 " is pushed on the screen of "Panasonic" while " press <F2 to enter Setup> " is displayed.
3. The setup utility starts and then takes notes of the content of the BIOS setup of present set.
4. " F9 " is pushed, " Yes" is selected on the screen of " Is the default value loaded? ", and " Enter"
is pushed.
5. " F10 " is pushed.
6. " Yes" is selected on the screen of the setup confirmation, and " Enter" is pushed.
7. The computer starts automatically.
Attention
If the device which can be set is set to "Invalidity" by "Advanced" or "Security" menu, becomes an
error by "PC-Diagnostic utility".
(It is judged that the device which can be set to "Invalidity" by "Main" menu such as "Flat pad" is
normal if the controller operates normally though sets to "Invalidity" by the setup. )
In the model with built-in DVD of the USB connection, even if DVD is normal, becomes an error if
legacy USB is set to "Invalidity"
1-2. When you execute an automatic test
1. "Ctrl" + "F7" is pushed while the "Panasonic" start screen is displayed after the computer is started.
2. The test of all devices begins automatically by "PC-Diagnostic utility"’s starting.
Attention
It is a test which the customer who bought PC can execute. (As for HDD, the enhancing test is also
possible.)
A flat pad does not work for a while after starting "PC-Diagnostic utility".
The movement of a flat pad might become abnormal If after RAM begins from the CPU/System
test, a flat pad will be operated in about 30 seconds. In that case,restarts pushing"Alt" + "Ctrl" +
"Del" key. Or, please start "PC-Diagnostic utility" again after doing the power supply switch in the
slide, and turning off the power supply.
1-3. When you execute the enhancing test
1. Please let me discontinue diagnosing clicking to end an automatic test.
2. Please click on the character of "D" "PC-Diagnostic utility" on the screen while pushing both of right
"Shift" and left "Shift" keys. D
3. All devices which can select the enhancing test make the setting of the enhancing test possible.
4. The district device is made"FULL" display (enhancing test).
5. The test begins clicking .
*Please refer to item 4 for the error result of each test and the division of the breakdown part.

2. Operation of PC-Diagnostic Utility
-Only the device which can be inspected on the entire screen is displayed.
-The item does not appear when the device of wireless LAN etc. is not physically connected.
-The movement of the item must use an arrow key or a flat pad.
-As for the device under the diagnosis, blue and yellow are alternately displayed at the left of the icon.
- The diagnosis result of the device greens at the left of the icon when it is normal, and becomes red when
abnormal.
-When the test of all devices ends, the test result is displayed under the right of the screen.
-Please click while diagnosing when being stop on the way by the time the test of all devices ends.
-Please click when you restart "PC-Diagnostic utility".
*Each device is tested from the beginning, and it is not possible to restart on the way.

2-1. Selection of tested device
-To test only a specific device, "Test" and "Do not test" of each device can be selected.
-The device which can select the enhancing test changes in order of "The standard is tested" and "Do not
test" whenever the device icon is clicked.
Start the standard test Do not test
Please begin testing clicking if the selection of the tested device ends.
2-2. "PC-Diagnostic utility" End method

When of "Close" on the right of the screen is clicked, the computer reactivates automatically. Or, the
power supply switch is done in the slide and the power supply is turned off.
2-3. The content of the setup is returned to the setting of the user
1. Turned on the computer.
2. "F2" is pushed on the screen while "Press<F2>to enter Setup" is displayed of "Panasonic".
3. Push "F10", and on the screen of "Is the change in the setting preserved and do end?"and then "Yes"
is selected, and "Enter" is pushed.
4. The computer reactivates automatically.
5. The end option is chosen by the start menu, and the power supply of the computer is turned off.
Standard at test time

All devices other than RAM and HDD about 1 minute
RAM standard test 1 - 2 minutes
HDD standard test 2 - 3 minutes
HDD enhancing test (60GB) about 40 minutes
Ex.The standard when the standard <all device> is tested becomes 1+2+3=6 minutes.
There is greatly a difference from RAM test when the memory is increased according to the perform-
ance of the memory occasionally.
Moreover, when the main body of PC under the test is a high temperature, it occasionally takes time.
There is greatly a difference from HDD according to the performance of the drive occasionally.

7.1. Test Item and Division of trouble
Place with possibili-

Test item Stanard Enhancing Content of standard test Content of enhancing test
ty of breakdown
CPU / CPU is shifted to protected mode, and CPU /

SYSTEM "Violation of the paging", "Operation of Main board
the violation of a privileged instruc-
tion", and DMA, INT, TIMER, and the
RTC operation are confirmed.
RAM All memory space is tested in a spe- Memory / Main-

cial memory access pattern based on board
"R.S.T . technology".
HDD The record area frequently accessed All record area is tested. HDD /
with Microsoft Windows XP to test in Mainboard /
about two minutes regardless of Cable /
points of HDD is emphatically tested. Connector
MODEM It is confirmed not to find abnormality MODEM/ Main-

in the AC97 modem controller. board
Wireless It is confirmed not to find abnormality Wireless LAN

LAN in the Wireless LAN modem controller. board /
Connector /
Mainboard
Sound *5
USB It is confirmed not to find abnormality It is confirmed not to find ab- Mainboard /
in the USB controller. normality in the wiring be- Connector
tween the USB controller and
*1 the connector by confirming
the connection of the USB
equipment connected with the
USB connector.
LAN It is confirmed not to find abnormality It is confirmed not to find ab- Mainboard /
*2 in the LAN controller. normality in the wiring be- Connector
tween the controller and the
connector by connecting to
HUB with LAN cable.
PC Card It is confirmed not to find abnormality Mainboard

in the CardBus controller.
SD It is confirmed not to find abnormality Mainboard

in the SD controller.
Keyboard *3 It is confirmed not to find abnormality The key is actually input, and Mainboard /
in keyboard controller’s keyboard inter- the operation is displayed on Keyboard
face. the screen.
Touch Pad *4 Whether keyboard controller’s mouse The operation is actually dis- Mainboard /
interface operates normally is con- played on the screen by oper- Touch Pad
firmed. ating the touch pad.
DVD-ROM *6 The drive is normally reset, and it is It is confirmed to be able to Mainboard /

accessible is confirmed. read media normally. Touch Pad

The place with possibility of
Test Item Standard Enhanced Content of Standard Test Content of Extend Test
breakdown
It is confirmed not to find
Perform Touch Screen
abnormality in the USB
functionality practically. Main board/
Touch Screen connection of Touch Screen.
Operator has to judge Touch Screen
This test cannot find
PASS/FAIL with test result.
abnormality of Touch Screen.
abnormality in the connection
Bluetooth Bluetooth cable
of Main board and Bluetooth
module.
abnormality in the connection
Wireless WAN WWAN cable
of Main board and Wireless
WAN module.
abnormality in the legacy FD FD Drive/
drive. Main board (Super I/O)/
Floppy
This test cannot find FDD cable
abnormality of mechanical FDD connector
breakdown. (e.g.. Head, Motor)
abnormality in access to Main board
VRAM with VESA. (Chipset, Graphic
Video
The PC which uses main Controller)/
memory as VRAM may fail with Memory
main memory failure.
GPS abnormality in the connection GPS cable
of Main board and GPS
Main board
IEEE1394 abnormality in the IEEE1394
(IEEE#394 Controller)
controller.
abnormality in the wiring Main board (Chipset)/
Express Card
between Chipset and Express Express Card Connector
Card.
Main board
Smart Card abnormality in the Smart Card
(Smart Card Controller)
controller.
abnormality in the wiring
abnormality of Super I/O
between Super I/O and Serial
UART function. Main board (Super I/O)/
Serial Port *7 Connector.
This test cannot find lack of Serial Connector
This test cannot find failure of
wiring between Super I/O and
cable characteristic and device
Serial Connector.
problems.
abnormality in the wiring
abnormality of Super I/O
between Super I/O and
parallel function. Main board (Super I/O)/
Parallel Port *8 Parallel Connector.
This test cannot find lack of Parallel Connector
This test cannot find failure of
wiring between Super I/O and
cable characteristic and device
Parallel Connector.
problems.
*1 Please connect the USB device with the port (USB connector) which wants to test before the tests.
*2 Please connect LAN port with LAN HUB with LAN cable before the tests.
*3 The operator actually inputs the key, and the operator judges PASS/FAIL of the test.
*4 The operator actually operates the mouse, and the operator judges PASS/FAIL of the test.
*5 It is not abnormal though the sound is emitted from the speaker while testing.
When the test result is PASS, trouble is thought by not hearing of the sound under the test from
the speaker and the headphone by the wiring of the audio output system.
*6 Please set DVD/CD media in the drive before the tests.
*7 Please set a Special Loop Back Connector Tool at serial connector for Enhanced Test.
(This Connector Tool is same as the one used before.)
*8 Please set a Special Loop Back Connector Tool at parallel connector for Enhanced Test.
(This Connector Tools is same as the one used before.)

8 Wiring Connection Diagram
BT PCB INVERTER PCB
CN1 CN2 BACK LIGHT
CN1
TS PS2 PCB LCD

CN901
Touch
HSDPA PCB Screen
CN900 Panel
EXTERNAL
DISPLAY
JK601
PORT SERIAL PORT
CN882 CN881 I/F PCB
JK600
CN604 CN880 CN883 CN850
JK880
CN600
DC-IN
RTC
BATTERY I/O PCB
H/P MIC
CN16
CN9 CN14
CN18
CN27 CN23
CN901
AUDIO PCB MODEM

CN24
PCB
CN3
KEYBOARD COIN
CN17 CN8 BATTERY
SD PCB
CN891
CN5
CN21 LAN
MAIN PCB PORT
CN12
CN11
HDD LAN-
AUX
CN15
CN4
MAIN
BATTERY
WIRELESS
PCMCIA UNIT MODULE
J1
POWER SW PCB
CN23 CN15
CN980 ANT PCB
TOUCH PAD HDD

FPC BAT GPRS
PAD PCB
LAN-
CN806 MAIN
CN805 CN801
CN800
CN804
CN802
RIGHT
LED PCB SW PCB LEFT LED PCB
CN841 CN950 CN780

9 Disassembly/Reassembly
Note:
Power off the computer. Do not shut down to the Suspend or hibernation mode.
Do not add peripherals while the computer is in the Suspend or hibernation mode; abnormal operation may result.
9.1. Disassembly Instructions HDD Case B

Hooks
9.1.1. Preparation
Before disassembling, be sure to make the following prepara- Hooks
tions.
HDD FPC
• Shut down Windows and turn off the power.
• Disconnect the AC adaptor. HDD
• Remove the optional DIMM memory card and PCMCIA card
if they are connected.
• Remove other devices if they are connected. Heater
Attention:
• Please execute writing BIOS ID when you exchange the
Main Board. <N13>
• Parts (Sheet and rubber) etc. related various the Conductive <N13>
Cloth and Heat Spreader cannot be recycled. Use new parts.
9.1.2. Removing the Battery Pack and

HDD Pack
HDD Case A
5. Remove the two Screws <N13>.

6. Remove the HDD Case A and the HDD Case B.
1 3 7. Remove the HDD
2
Screws <N13> : DXQT2+D4FNL
9.1.3. Removing the Touch Pad and Key-

board
KBD Plate
<N9>
<N9> KBD Plate
<N9>
Palm Rest Ass’y
<N9>
HDD Pack
Battery Pack
1. Open the Battery Cover.

2. Remove the Battery Pack.
3. Open the HDD Cover.
4. Remove the HDD Pack.
1. Remove the Palm Rest Ass'y.
Note:
The Palm Rest Ass'y is firmly fixed with two-sided
tape.
Carefully remove the Palm Top Cover Sheet not to
damage it.
2. Remove the 4 Screws <N9>.
3. Remove the KBD Plate.

10. Disconnect the Cable from Connector (CN800).
11. Remove the Touch Pad and Click Button Plate.
Screws <N1> : DFHE5025XA

Screws <N9> : DRSB2+5FKL
1
9.1.4. Removing the DIMM Lid Ass’y
2 <K14-8>
<K14-8> <K14-8>
<K14-8>
DIMM Lid Ass’y
Keyboard
4. Lift the far side of the Keyboard and slide it to backward,

and then turn the Keyboard over frontward.
<N1>
1. Remove the 4 Screws <K14-8>.

2. Remove the DIMM Lid Ass'y.
KBD
Connector
Cover Screws <K14-8> : DRHM5025YAT
9.1.5. Removing the Rear Cabinet

<N10>
<N10>
<N10>
<N10> <N10>
<N10> <N10>
<N10>
<N10>
5. Remove the 3 Screws <N1>. <N10>
<N10>
6. Remove the KBD Connector Cover.
<N10>
Keyboard
<N10>
Keyboard
FPC
TP Tape
Touch Pad
2. Open the LID Rubbers.
Click Button
Plate 3. Remove the Rear Cabinet.
Screws <N10> : DRHM0061ZA
Connector Connector
(CN800) (CN18)
7. Disconnect the Cable from Connector (CN18).

8. Remove the Keyboard.
9. Remove the TP Tape.

9.1.6. Removing the DU Lid Unit
<N19>
<K14-9> Connector(CN1)
<K14-9> <K14-9> Bluetooth PCB
Antenna Cable(blue) Plate
<K14-9>
Clamper
HSDPA PCB Connector(CN604)
<K14-9>
DIMM Lid Angle <N19>
<N19>
DU Lid
6. Disconnect the Antenna Cable from the Clamper.

7. Disconnect the Antenna Cable.
2. Remove the DU Lid Angle and DU Lid.
8. Remove the 4 Screws. <N19>
9. Disconnect the Cable from the Connector (CN604).
Screws <K14-9> : DXQT2+D25FNL
9.1.7. Removing the HSDPA PCB and 11. Disconnect the Cable from the Connector (CN1) and
Bluetooth PCB remove the Bluetooth PCB and HSDPA PCB.
Tape Screws <N9> : DRSB2+5FKL

Screws <N19> : XSB2+3FNL
<N9> <N9>
<N9>
Antenna Cable(brown) 9.1.8. Removing the Audio PCB
<N9> Antenna Cable(black)
HSDPA PCB <N9>
<N9>
Connector(CN600) <N9>
Audio PCB
Cable Holder Cushion
Connector(CN901)
1. Remove the Cable Holder Cushion.

2. Disconnect the 2 Antenna Cables (brown, black).
3. Remove the Tape. 1. Remove the 3 Screws <N9>.
4. Remove the 4 Screws. <N9> 2. Disconnect the Cable from a Connector (CN901).
5. Disconnect the Cable from the Connector (CN600). 3. Remove the Audio PCB.
Screws <N9>:DRSB2+5FKL

9.1.9. Removing the Main PCB, Wireless
<N8>
Module, SD PCB, Antenna PCB and <N8>
Modem PCB HDD
Connector Guide
<N19>
<N19>
Connector(CN21)
<N9>
<N9>
SD PCB Ass’y
Connector(CN8)
BAT FPC Ass’y
Connector(CN17)
Note:
This procedure is not necessary if the computer is not
equipped with Wireless Module or Modem PCB.
1. Disconnect the 2 LCD Cables. (CN8,CN17) Connector(CN15)
<N3> DU PCB 5. Remove the 2 Screws <N8>, and remove the HDD Con-
<N3> <N9>
<N9> nector Guide.
<N9>
7. Disconnect the Cable from the Connector. (CN15)
Antenna PCB Plate
8. Remove the BAT FPC Ass'y.
<N3> 10. Disconnect the Cable from the Connector (CN21), and
<N3> remove the SD PCB Ass'y.
<N19>
DIMM Holder Wireless Module
<N19> <N19> <N19>
<N19> <N19>
Modem PCB
Connector(CN3)
gray cable black cable white cable
2. Remove the gray, black and white Antenna Cables.

3. Remove the 2 Screws <N3> and the 3 Screws <N9>.
4. Remove the 2 screws <N3>, and remove the DU PCB, Coin Battery
Plate and Antenna PCB.
11. Disconnect the Cable from the Connector (CN3), and

remove the Coin Battery.
12. Remove the 2 Screws <N19>, and remove the Wireless
Module.
13. Remove the 2 Screws <N19>, and remove the Modem
PCB.

14. Remove the 2 Screws <N19>, and remove the DIMM Screws <N2> : DFHE5058ZB
Holder. Screws <N9> : DRSB2+5FKL
Tape 9.1.11. Removing the Power SW PCB

<N19>
<N19> <N1>
<N19>
Connector(CN9)
Connector(CN9)
<N19>
Power SW
PCB
Connector(CN14)
<N19>
Connector(CN23) Main PCB
Combo Socket
1. Remove the Screw <N1>.

3. Remove the Power SW PCB.
Screw <N1> : DFHE5025XA
9.1.12. Removing the left LED and right

LED PCB
Release Paper
15. Remove the Tape.
16. Disconnect the 3 Cables from the 3 Connectors. Release Paper
(CN9,CN14,CN23)
17. Remove the 7 Screws <N19>, and remove the Main PCB
and Combo Socket.
left LED PCB
Screws <N3> : DFHE5108ZA
9.1.10. Removing the I/O PCB Ass'y

<N9>
I/O PCB Ass’y <N9> Connector(CN806)
right LED PCB
Connector(CN801)
<N2>
<N2>
<N2>
<N2> 1. Remove the two Release Papers.
3. Remove the left LED PCB.
5. Remove the right LED PCB.
1. Remove the 4 D-SUB Screws <N2>.

3. Remove the I/O PCB Ass'y.

9.1.13. Removing Pad PCB and SW PCB 9.1.14. Removing the Display unit
<N1> <N1>
<N1> <N1>
<N1>
Connector(CN807)
<N1>
Pad PCB
Connector(CN805) LCD Hinge Cover
<N1>
<N1>

2. Remove the LCD Hinge Cover.
1. Disconnect the 2 Cables from the 2 Connectors

(CN805,CN807).
<N9> Hinge Cover
3. Remove the Pad PCB.
<N9>
SW PCB
3. Display unit is half-rotated and removes the 2 Screws
<N9>.
<N18>
Operation Sheet <N18>
<N18>
<N18>
4. Remove the Operation Sheet and the SW PCB.

5. Turn the computer over.
6. Remove the Display Unit.

Screws <N18> : DXYN4+J7FNL

9.1.15. Removing the LCD Rear Case 9.1.17. Removing Inverter PCB and LCD
Unit
<N15>
<N15> <N16> LCD Rear Case
<N15> Tape
<N16>
<N15>
<N15> <N15>
Connector
Inverter Case Inverter PCB
Antenna Cover <N15> Connector

<N7> <N15> Connector
<N15> (CN901)
<N15>
<N7> TS PCB
<N7> Connector (CN900)
<N7>
<N7> <N7>
<N7>
<N7>
<N7> <N7> <N7> <N7>

<N7>
<N7> LCD Unit
<N7> <N7> Antenna Cover
Tablet Latch Cover
1. Disconnect the 2 Cables from 2 Connectors (CN1,CN2).
1. Remove the 8 Screws <N7> on the front side of Display 2. Remove the Inverter Case and Inverter PCB.
unit. 3. Disconnect the 2 Cable from 2 connector
2. Remove the 8 Screws <N7> on the back side of Display (CN900,CN901).
unit. 4. Remove the TS PS2 PCB, then remove the LCD unit.
3. Remove 2 Antenna Covers and Tablet Latch Cover.
9.1.18. Removing WWAN Main Antenna
5. Remove the 2 Screws <N16>. PCB, LAN-Main BT Antenna PCB,
6. Remove the LCD Rear Case. LAN AUX Antenna PCB and WWAN
AUX Antenna PCB
Screws <N7> : DRQT26+E5FKL
Screws <N15> : DXYN2+J6FNL Pen <K10-1-13>
WWAN Aux
Screws <N16> : DXYN3+J10FNL Antenna PCB <K10-1-13>
LAN-Main <N1>
9.1.16. Removing the LCD Hinge BT Antenna PCB <N1> Pen Holder
<N1>
Cable <N17>
Holder <N1>
Plate <N17> Cable
Holder
LCD Plate
Hinge Cable <N1>
Holder <N1>
LAN Aux
LCD Cable Antenna PCB
Cable Holder Holder <N1>
Plate Sheet
WWAN Main
<N1> Antenna PCB
Cable
Holder
2. Remove the WWAN Main Antenna PCB.
4. Remove the LAN-Main BT Antenna PCB.
6. Remove the LAN AUX Antenna PCB.
8. Remove the WWAN AUX Antenna PCB.
1. Remove the Cable Holder. 9. Remove the Pen
2. Remove the 2 Screws <N17>. 10. Remove the two Screws <N6>.
3. Remove the Cable Holder Plate and LCD Hinge. 11. Remove the Pen Holder.
Screws <N17> : DXYN3+J8FNL Screws <N1> : DFHE5025XA

Screws <N6> : DRHM5025YA

9.1.19. Removing the Each Cover
<N6>
DC IN LID Rubber
USB LID Rubber
LAN LID Rubber
Moden/LAN LID Rubber
<N6> <N6>
<N6>
<K12-16> <N6>
<K12-16> <N6> <N6>
<K12-16> <N6>
<K12-16> <N6>
Serial
LID Rubber
<K12-16>
Battery
LID ASS’Y
HDD LID ASS’Y
Audio
LID Rubber
USB Back
Rubber PCMCIA LID ASS’Y
RGB
LID Rubber

2. Remove the Modem/LAN LID Rubber, LAN LID Rubber,
USB
LID Rubber, DC IN LID Rubber, Serial LID Rubber, RGB
LID Rubber, Audio LID Rubber and USB Back Rubber.
3. Remove the Rear Cabinet.
(Refer to 7.1.5 Removing the Rear Cabinet)
5. Remove the Battery LID ASS'Y, HDD LID Ass'y and
PCMCIA LID Ass'y.
Screws <K12-16> : DRQT26+D3FKL

Screws <N6> : DRHM5025YA

9.2. Reassembly Instructions
9.2.1. Attention when CF-19 series is repaired
• Please execute writing BIOS ID when you exchange the Main Board.
• Parts (Sheet and rubber) etc. related various the Conductive Cloth and Heat Spreader cannot be recycled. Use new parts.
9.2.2. Setting up the Inverter Ass'y and LCD UNIT

1. Set the LCD UNIT to the LCD Front Cabinet/TS Panel.
2. Set the TS PCB on the LCD Back Damper, and connect Tape
the 2 Cables to the Connectors (CN900 and CN901).
3. Set the Inverter PCB to the LCD Back Damper, and con-
Connector
nect the 2 Cables to the Connectors.
Inverter Case Inverter PCB
Connector
Connector
(CN901)
TS PCB
Connector (CN900)
LCD Unit
n Assembly of LCD Back Damper (Applicable Model : Touch Screen Model)
Detail of "B" Detail of "C" Detail of "D"

0 1mm 0 1mm 0 1mm
0 0.5mm
Pass the Cable 0 0.5mm Pass the Cable Pass the Cable
under the protrusion. through the space. 1 1.5mm under the protrusion.
LCD Side Cushion S LCD Back Cushion S

B C LCD Back Cushion L
D
Note: Apply the load to attach. 20 to 30N (2.0 to 3.0 Kgf)
After setting LCD
After setting LCD
Order of fixing Back Damper,
Back Damper,
fix them together.
fix them together.
Screw
Screw
Detail of "A" A Remove the Release Paper on Holder Sheet
the back side and attach it. 0 0.5mm
0 3mm LCD Back Damper
Lengthwise: Match to the LCD Frame.
Holder Sheet Crosswise: Match to the middle line.
0 0.5mm
LCD Back Cushion Side LCD Back Cushion Side
0 0.5mm Cover the hook of

Cover the hook of
the Frame. (0 to 0.5 mm)
the Frame. (0 to 0.5 mm)
LCD Side Cushion A
Attach to the side surface if the Frame. Match both Holder Sheet and LCD
(Match to the end of the Frame within Back Cushion Side to the right Match both Holder Sheet and LCD
0 to 0.5 mm at the far side.) edge of the Frame. (0 to 0.5 mm) Back Cushion Side to the right
edge of the Frame. (0 to 0.5 mm)
LCD PWB
SPACER ASSY
Insert this between
LCD PCB & LCD Frame.
Screw
Screw the Board and
Screw
the Spacer together. LCD Side Cushion D Screw the Board and
LCD Side Cushion C the Spacer together.
LCD Side Cushion C
LCD PWB SPACER ASSY 0 0.5mm
Spacer Sheet 0.5mm
Spacer Sheet 0.5mm
LCD PCB Spacer
Asymmetric Shape
0.5mm 0.5mm
0.5mm

n Assembly of LCD Back Damper (Application Model : Digitizer Model)
0 0.5mm
PCB
2 0.5mm
PCB
Attch to the side surface

of the Frame.
Match to the end of the
Frame within 0 to 0.5 mm 10 2mm
at the far side.
Screw the Board together
0 0.5mm 0 0.5mm
0 0.5mm
0 0.5mm 0 0.5mm 0 0.5mm
n Assembly of Inverter PCB
Confirm the direction of the

Inverter Case Bottom Inverter board when attaching.
Insert it as the protrusion of
Important Parts Do not press the Insert from the direction the Inverter Case Upper come
for Safety piezoelectric transformer. of hole and notch. to the gap side of INverter MIl Cover.
Inverter Inverter MIL Cover
2 4mm
Remove the Release Paper,

and then attach the Inverter.
MIL Sheet
Wrap the Sheet to
overlap it on the side.
Set the Inverter Case Bottom to make it outside.

n Assembly of Inverter PCB (Applicable Model : Touch Screen Model)
Avoid any stress on the Cable when
connecting the CCFL Cable.
Hold the Connector part when
connecting/disconnecting.
Attach it to the Connector and FPC.
LCD Side Cushion E
12 Connector
Insert it between the ribs.
Insert it between the ribs. PWB
FPC (Fit to the Cabinet.)
(Fit to the Cabinet.)
Cushion High
LCD Side Cushion E Voltage Label
TS PWB LCD Side Cushion F
Insulation Parts Insulation Parts Insert it between the ribs.
Connect
(Fit to the Cabinet.)
Inverter Ass’y 0 3mm
Confirm the direction of the Inverter board when attaching.

Inverter Mil Sheet
30 35mm
LCD Ass’y Inverter Ass’y

The gap side is front. Connect the Cable to the
Inverter Ass’y 0 0.5mm Tape
left and right Connectors.
Sub material: Pet Tape 1 Attach the Inverter Ass’y in the
Details of "A" middle of right and left.
Avoid any stress on the Cable Attach the surplus of the right and left sides on the
Safety Working Ensure the edge of the
conductive fabric is not
when connecting it. Back Dumper as shown below and overlap on the
Hold the Connector part when CCFL Cable. Attach the Pet Sheet over the Core.
frayed. connecting/disconnecting.
Note for attaching Conductive Tape
LCD Cable TS
Details of Cable Conductive Tape
Avoid running Wind round the LCD Cable
over this rib. a few times and attach it. Inverter Ass’y
Sield Sheet LCD Back Dumper
1 2 Avoid getting under the Sheet. Fix the two Cables.
mm A
0 1mm 0 1mm Insulation Parts 0 4mm
Insulation Parts
6 2mm from the

Connect branch point
0 1mm 0 1mm
Attach coming over the end of steel plate by 1 to 2 mm.

Conductive Tape
Avoid any stress on the Tab part of the
LCD Module because the line comes off.
Wrap over the Antenna Cable
0 1mm Wrap of Antenna Cable Cushion and the Cable.
Cushion E

n Assembly of Inverter PCB (Application Model : Digitizer Model)
Inverter Ass’y
LCD Back Dumper
Conductive Tape
n Assembly of Touch Screen (Applicable Model : Touch Screen Model)
A Details of "A"
Touch Screen Ass’y Back Side
6 0.5mm
Protect Sheet
OK
Laminate TS FPC
Attach it to the front side. Spacer
(Note) (Using the jig)
T/S Dimensional tolerance: 0.2
Apply the load 20 to 30N (2.0 to 3.0 Kgf) to the Cushions.
NG 0 0.5mm
Laminate
T/S
Match to the wall of the
Cabinet. 0 to 0.5 mm
Touch Screen
TS Spacer A
0 1mm 0 1mm
Attach the surface to the LCD Front.
Match to the marking line.
0.5 mm
TS Spacer B TS Spacer B
Avoid running over. Ensure 4 and 5 do not run over the display side. LCD Side Cushion B
Touch Screen Ass’y TS Spacer A

0 1mm Match to the marking line.
0.5 mm
0 1mm

n Assembly of Glass (Applicable Model : Digitizer Model)
9.2.3. Assembling the WWAN Main Antenna PCB, LAN-Main BT Antenna PCB, LAN AUX
Antenna PCB, WWAN AUX Antenna PCB and Pen holder
1. Fix the Pen Holder using the 2 Screws. <K10-1-13>
2. Attach the Pen. Pen <K10-1-13>
WWAN Aux
3. Fix the WWAN AUX Antenna PCB using the 2 Screws. Antenna PCB <K10-1-13>
<N1> LAN-Main <N1>
BT Antenna PCB <N1> Pen Holder
4. Fix the LAN AUX Antenna PCB using the 2 Screws. <N1> <N1>
5. Fix the LAN-Main BT Antenna PCB using the 2 Screws.
<N1> <N1>
6. Fix the WWAN Main Antenna PCB using the 2 Screws.
<N1> <N1>
<N1>
Screws <N1> : DFHE5025XA LAN Aux
Screws <K10-1-13> : DRHM5025YAT Antenna PCB
<N1>
WWAN Main
<N1> Antenna PCB

n Line Processing of Antenna Cable
Safety Working
Details of "B"
Avoid running over

the rib, etc..
Note: Avoid any stress on the solder. Match to the edge of Cabinet Match to the edge of Cabinet
B
A
Screw Screw
EVDO/EDGE Antenna
Safety Working Cable Cushion Attachment Method Safety Working

(3 Places)
Details of "A" Bundle and wind 3 Insert it between the wall and the rib after attaching.
antenna cables.
LAN Main
/BT ANT
Cable Cushion Avoid running over the rib, etc..
Avoid running over
the rib, etc.. Details of "D"
Insert it between the pins. Screw

Match to the
Screw edge of Cabinet
Hook it.
Put the Cable on each hook
Screw Screw
LAN-AUX ANT EVDO-AUX
Screw
Match to the edge of Cabinet Screw
Safety Working C D
Details of "D" Match to the
edge of Cabinet
Avoid running over Put the Cable on each hook Put the Cable on each hook
Tape Pen Holder
the rib, etc.. Cable Cushion
Cable Cushion
Cable Cushion
Put the center of Cushion between the ribs.
9.2.4. Setting up the LCD Hinge

1. Wind the Cable coming out of the LCD Unit counterclock-
wise to the LCD Hinge. Cable <N17>
Holder
2. Set the Lock Plate and the Hinge Top Cover, and rotate Plate <N17> Cable
Holder
the LCD Hinge to turn the Display Unit to front LCD Plate
3. Put the LCD Cable and the Antenna Cable in the Cable Hinge Cable
Holder. Holder
4. Fit another Cable Holder and clamp the Cable Holders in
LCD Cable
the LCD Hinge. Cable Holder Holder
5. Fix the LCD Hinge using the 2 Screws <N17> and the 2 Plate Sheet
Cable Holder Plates. Cable
Holder
Screws <N17 > : DXYN3+J8FNL

n Assembly of LCD Hinge
Safety Working
Ensure the "C" side comes

to the lower right corner
when viewing from above. Using the fixing jig when fixing the Hinge
Initial Condition Fix Fix

of LCD Hinge Cable Hold Plate Cable Hold Plate
Tighten
Screw Safety Working

Avoid catching the Cable. If you arrange the Cable in the area,
you do not need to use the fixing jig.
LCD Hinge
Rotation Direction Screw Avoid catching the Cable (when repairing or when not using the jig).
Temporarily fix the both sides ("A") of the Hinge using the Screw, and fix the Cable Hold Plate.
After fixing the Cable Hold Plate, remove the screws from the both sides ("A").
n Line Processing of Antenna Cable and LCD Cable
Safety Working
Allow some cable margin.
Margin: 22 3 mm
You will hear the sound when they are firmly jointed.
Rotation Direction
Lock Plate Assy
Turn the Cable
360 degree.
Lock Spring
Insert the Lock Spring (the bottom diameter is shorter),
and then insert the Lock Plate from above.
Cable Holder Wind the Antenna cable first. Hinge Cover Assy
Pass the Cables through it, and then fix it to the Hinge.
(Fix directly the other side.)
For fixing, hold the Hinge parallel to the LCD.
LCD Rear side
LCD Cable Holder
Joint it to the Hinge Cover hook after

connecting the cable to the notch.
Protect Sheet
Process in the order of black/white/blue/gray/brown cables from the left.

(This process does not need if there are not cables.)

9.2.5. Assembling the Antenna Cover, the Tablet Latch Cover and the LCD Rear Case
1. Fix the LCD Rear Case using the 10 Screws <N15> and
the 2 Screws. <N16> <N15>
2. Attach the Antenna Covers and the Tablet Latch Cover to <N15> <N16> LCD Rear Case
<N15> <N16>
the Display Unit. <N15>
3. Tighten the 8 Screws <N7> on the back of the Display <N15> <N15>
Unit.
4. Turn the Display Unit over, and tighten the 8 Screws.
<N7>
Antenna Cover <N15>
<N7> <N15>
<N15>
Screws <N7> : DRQT26+E5FKL <N15>
Screws <N15> : DXYN2+J6FNL <N7>
Screws <N16> : DXYN3+J10FNL <N7>
<N7>
<N7> <N7>
<N7>
<N7>
<N7> <N7> <N7> <N7>

<N7>
<N7>
<N7> <N7> Antenna Cover
Tablet Latch Cover
n Assembly of LCD Front Case

Do not use if the protrusion such as painting lump exists around D5.
(Due to affect the Touch Screen operations.)
Insert it between the ribs, and attach it.
LCD Front Assy

Magnet Ass’y
0 0.5mm
Magnet Tape
0 1mm
Magnet
Avoid running over 1mm (Both on the top and the side)
Avoid running over
Tape
Note for attachment

Avoid running over the display part.
Attach and apply the load 30 to 40N (3.0 to 4.0 Kgf).
Attach here Position of pasting D.

0 0.5mm Fit to the rib
0 0.5mm
0 0.5mm

n Assembly of LCD Rear Case (Applicable Model : Touch Screen Model)
(Note)
Arrow without specified measurement: 0 to 0.5 mm
Allowable right/left displacement of the Cushion: max. 0.5 mm
LCD Rear Cushion A LCD Rear Cushion A

LCD Rear Cushion F LCD Rear Cushion F
LCD Rear Cushion F
0 0.5mm
Marking line
0 1mm Marking line Attach it between marking lines. 0 1mm
0.5mm 0 to 1 mm from one of the lines.
0.5mm LCD Rear Cushion G
LCD Rear Assy

LCD Rear Cushion G
LCD Rear Cushion B
LCD Rear Cushion B
Marking line
Marking line 0.5mm
0.5mm
LCD Rear Cushion C

Marking line
0 1mm
LCD Rear Cushion C
LCD Rear Cushion E LCD Rear Cushion D LCD Rear Cushion E
n Assembly of LCD Rear Case (Applicable Model : Digitizer Model)

(Note)
Arrow without specified measurement: 0 to 0.5 mm
Allowable right/left displacement of the Cushion: max. 0.5 mm
LCD Rear Cushion F LCD Rear Cushion A

LCD Rear Cushion A LCD Rear Cushion F LCD Rear Cushion F
0 0.5mm
0 1mm Marking line Attach it between marking lines. Marking line 0 1mm
0.5mm 0 to 1 mm from one of the lines. 0.5mm
LCD Rear Cushion C LCD Rear Cushion C
LCD Rear Ass’y Marking line

0.5mm
Safety Working
Marking line
Important Parts 0.5mm
for Safety
Safety critical component
LCD Rear Cushion A
LCD Rear Cushion C
LCD Rear Cushion E

0 3mm
LCD Rear Cushion E LCD Rear Cushion D LCD Rear Cushion C

LCD Rear Cushion C

n Assembly of Tablet Latch Cover and Antenna Cover
Press and hold it against the cabinet,
Tablet Lacth Cover and fix it using the Screw.
Antenna Cushion L
Antenna Cover Attach it matching to the silk to put the

two-sided tape on the Antenna side.
Press and hold it against the cabinet,
and fix it using the Screw.
Screw Locations
Screw 10 Places
Screw 16 Places
Fix in the order.

the front side as well,
8 screws each side
Do not forget fixing with screws. Antenna Cover

Screw Screw Press and hold it against the cabinet,
and fix it using the Screw.

9.2.6. Setting the Display Unit
1. Fix the Display Unit using the 2 Screws <N9>.
2. Close the Display Unit and turn the computer over, then <N18>
<N18>
fix the Display Unit using the 4 Screws <N18>. <N18>
<N18>
3. Turn the computer over and fix the LCD Hinge Cover
using the 2 Screws <N1>.
<N9> Hinge Cover
<N9>
4. Open the Display Unit and fix the LCD Hinge Cover using
the 2 Screws <N1>. <N1>
<N1>
Screws <N18> : XYN4+J7FNL LCD Hinge Cover
<N1>
<N1>

n Assembly of Display Unit
Safety Working
Note
Avoid any stress on the Cable.
Details of "A"
Screw Screw
Order of fixing Screw Screw
Screw Screw Screw Screw
Pass the Cable through

the groove.
Note: Running over
affects the waterproof
performance..
Close the LCD hooking the
Hinge on the Top Case, and
then fold back.
Black/White Blue/Gray Brown
LCD UNIT
Set to the Top Case Assy
Insert all of antenna cables

into the notch of the board.
LCD Cable Insert Position

9.2.7. Setting the Pad PCB and SW PCB
1. Attach both the SW PCB and the Operation Sheet to the
Cabinet.
SW PCB
Operation Sheet
2. Connect the 3 Cables to the 3 Connectors.

(CN800,CN805,CN807) <N1>:No.3
<N1>:No.2
3. Fix the Pad PCB using the 4 Screws. <N1> <N1>:No.1
Note: Connector(CN807)
Tighten the Screws in the numbered order (No1 to
<N1>:No.4
No4). Pad PCB
Connector(CN805)

n Assembly of the Pad PCB and SW PCB
(Note) Arrow without specified measurement: 0 to 0.5 mm
PAD PWB ASSY PAD PWB
LED(R) FPC
SW FPC Insert
PAD MAIN FPC ASSY
Back side Power SW Cable
No direction when inserting
Insert Power Cable Cushion Insert
Wrap around the Cable.
8 2mm
Thermistor
Insert
PAD MAIN FPC Ass’y SW PCB Ass’y

PAD-Main FPC Operation Tape Ensure that the direction
Stiffening Plate Side
is right when attaching.
Match the edge The Connector bracket is
and attach it. on the back side.
Fold back
0 1mm
SW PCB
0 1mm
Tape Operation
Avoid coming off of the LED part, Sheet
or running over the LED part.
n Putting of the TP Bottom Tape
Front side SW PCB Ass’y

Match to the upper left corner. 0 to 0.5mm
Screw Screw
9.2.8. Setting the left LED PCB and right LED PCB
1. Connect the Cable to the Connector. (CN806)
2. Fix the left LED PCB. Release Paper
3. Connect the Cable to the Connector. (CN801) Release Paper
4. Fix the right LED PCB.
5. Attach the two Release Papers.
6. Attach the Palm Rest Ass'y.
left LED PCB
Connector(CN806)
right LED PCB
Connector(CN801)

n Assembly of the left LED PCB and right LED PCB
LED(L) PCB Ass’y LED(R) PCB Ass’y Match the edge and attach it.
LED Light Guide Sheet(R)
LED PCB(L)
LED Light Guide Sheet(L)
Match the edge and attach it.
Avoid running over the LED. LED PCB(R)
Back side
0 3mm LED PWB Tape(R)

LED PCB Tape(L)
LED(L) FPC

Ensure it does not come over the end
of the Board by 0.5 mm or more.
Avoid coming over it.
9.2.9. Setting the Power SW PCB

<N1>
2. Fix the Power SW PCB using the Screw. <N1> Connector(CN9)
Screws <N1> : DFHE5025XA Power SW

PCB
n Assembly of the Power SW PCB

(Note) Arrow without specified measurement: 0 to 0.5 mm
Power SW PCB
0 1mm
1
Power Spring Sheet
Attach
0 1mm 2
Insert
Spring
Insert it to Knob and
Pin on the Top Case Insert the Cushion
between the ribs.
Avoid coming over
Safety Working
Screw
Fold the board back and fix with screw.

9.2.10. Setting the I/O PCB Ass'y
1. Fix the I/O PCB using the 2 Screws. <N9>
2. Fix the I/O PCB using the 4 Screws. <N2> <N9>
I/O PCB Ass’y <N9>
Screws<N2> : DFHE5058ZB
Screws<N9> : DRSB2+5FKL
<N2>
<N2>
<N2>
<N2>
9.2.11. Setting the Main PCB, Wireless Module, SD PCB, DU PCB, Antenna PCB and
Modem PCB
1. Fix the Main PCB using the 7 Screws <N9>.
2. Connect the 3 Cables to the 3 Connectors. Tape
<N19>
(CN9,CN14,CN23) :No5
3. Attach the Tape. <N19>
<N19>
Tape
<N19> :No4
:No6 Connector(CN9)
<N19>
:No2
<N19> Connector(CN14)
:No1
<N19>
:No7
Connector(CN23) Main PCB
Combo Socket

4. Fix the Modem PCB using the 2 Screws <N19>.
5. Fix the Wireless Module using the 2 Screws <N19>. <N19>
DIMM Holder Wireless Module
6. Fix the DIMM Holder using the 2 Screws <N19>. <N19> <N19> <N19>
<N19>
7. Attach the Cable to the Connector (CN3) and attach the <N19>
Coin Battery.
Modem PCB
Connector(CN3)
Coin Battery
8. Fix the SD PCB Ass'y using the 3 Screws <N19>.

9. Attach the Cable to the Connector (CN21). <N8>
10. Hook the Flex Cable on the DIMM Holder, and turn 90 <N8>
HDD
degrees. Connector Guide
11. Fix the BAT FPC Ass'y using the 2 Screws <N9>. <N19>
<N19>
12. Connect the cable to the Connector. (CN15) Connector(CN21)
13. Fix the HDD Connector Guide using the 2 Screws <N8>.
<N9>
<N9>
SD PCB Ass’y
BAT FPC Ass’y
Connector(CN15)

14. Fix the DU PCB and the Plate using the 2 screws <N3>.
15. Fix the DU PCB Ass'y and Antenna PCB using the 3 <N3> DU PCB
<N3> <N9>
screws <N9> and the 2 screws <N3> . <N9> <N9>
16. Connect the white, black and gray Cables.
Antenna PCB Plate
<N3>
<N3>
white cable black cable gray cable
17. Turn the computer over, open the Display Unit, and then
connect the 2 LCD Cables. (CN8,CN17)
Note:
Tighten the Screws in the numbered order (No1 to No7).
Screws <N3> : DFHE5108ZA

Screws <N9> : DRSB2+5FKL Connector(CN8)
Connector(CN17)

n Assembly of Main PCB
Process in the order of 1 2 3 4.
MDC Modem Tape
Modem Cable
Basteraid
Connect to the MDC connector.
Fold the Tape in half.

0 1mm
0 1mm
Fold back
Basteraid
0 1mm
0 1mm
Cover the Screw head
If one screw is supplied, insert into the DIMM lower slot. MODEM PCB Set
If two screws are supplied, insert into the DIMM upper and lower slots. Fix the Screw (#5) from the back side.
Hexsagon Spacer H4.2

Coin Battery Preparation Coin Battery
Sub material (19mm width x 3 cm)
Wrap
10 3 mm
Screw
Screw
Screw
0 1mm Screw
MDC Assy
CPU Sheet
Sheet
Attach it on the board before

setting the Coin Battery.
0 1mm
LAN Cable
DIMM SLOT
Do not cover the screw hole
when setting the Coin Battery.
Avoid coming over the horizontal

DIMM Assy
line of the cross mark on the board.

Match to the edge of the Board.
0 to 1mm
Fold back and attach it

Insulation Tape Back side
Match to the Connector.

0 to 1 mm
Remove the DIMM and attach the Sheet.

Set the DIMM after attaching the Sheet.
DIMM Sheet
Match to the silk

0 0.5mm
Match to the silk

DIMM Sheet 0 0.5mm
Match to the silk Match to the silk

0 0.5mm 0 0.5mm

n Assembly of Main Unit
Screw Insert and then lock. Main PCB Ass’y

Connect
Audio FPC Ass’y
Stiffening Plate Side Details of the LAN/MODEM
Audio FPC
Audio FPC Ass’y
Lengthwise Insert it before setting
Attach it on the the Main Board. DU PCB ASSY
center of the
FPC.
3mm Screw
Tape Screw
Fold back Screw Screw
0 1mm Apply the lubricant (sub material) on the
Screw Screw
HDD Connector for about 1 second.
(Note for spraying around when applying.)
Round to make the brown side

outside and insert the notch. Screw
Thermal Sheet
Center of module
to the notch
Wireless Module Screw
Screw
Safety critical componentInsert
and then lock.
Insert the Bastaraid between
Important Parts the LAN/MODEM Connectors.
for Safety
Avoid running the Cable

over the Connector.
Insert and then lock
Thermal Rubber
Fit it to the corner of the SD board
Screw
HDD Connector Guide

Insert the FPC
Screw
SD PCB Ass’y
Screw Screw
Screw
Ensure that the knob is fit to SW when setting.
DIMM HOLDER Ass’y

RF SW Knob
Insert the hook
DIMM Holder
Screw
Screw

Insert the end of the Sheet into the space between the Main
Ensure that both top and Board and the bottom of the PCMCIA Slot.
bottom are hooked. (Left and Right 0.5mm, Apply 20 to 30N (2.0 to 3.0 Kgf))
Attach it fitting to the right.
0 0.5mm
Screw 0 0.5mm
Battery FPC Ass’y

Side surface
Slide the Battery FPC Ass’y

Screw
SD Blind Sheet
Insert the FPC as illustrated
9.2.12. Setting the Audio PCB

<N9>:No1
2. Fix the Audio PCB using the 3 Screws. <N9> <N9>:No.2
<N9>:No.3
Note: Audio PCB
Tighten the Screws in the numbered order (No1 to No3).
Connector(CN901)

9.2.13. Setting the HSDPA PCB and Bluetooth PCB
1. Fix the Plate and Bluetooth PCB using the 2 Screws
<N19>. <N19>
Bluetooth PCB
4. Fix the Plate and the Board using the 4 Screws <N19>. Plate
Antenna Cable(blue)
5. Attach the blue Antenna Cable to the Clamper. Clamper
<N19>
:No.4 <N19>
<N19> <N19> :No.2
:No.1 :No.1

7. Fix the RF PCB Ass'y using the 4 Screws. <N9> Tape
8. Attach the Tape.
9. Attach the brown and black Antenna Cables. <N9> <N9> Antenna Cable(brown)
<N9>
10. Attach the Cable Holder Cushion. <N9> Antenna Cable(black)
HSDPA PCB
Connector(CN600)

n Line Processing of Antenna Cable of Main Unit
Cable Process 1/3
Step 1 Step 3
After connecting the black antenna cable,
connect it into the Holder as illustrated.
Place brown/blue/gray cables at left and
white/black cables downward.
Put the surplus under along the rib.
Step 2 Step 4
After connecting the white antenna cable,
connect it into the Holder as illustrated. After connecting the gray antenna cable,
connect it into the Holder as illustrated.
Cable
Step 9
Connect the blue antenna cable.
Cable Process 2/3

Step 7
Sheet Attach Side Insert it into the right

notch of the Clamper.
Step 5
0 1mm
Audio PCB Ass’y Check the blue cable from the hole.
Remove the Release Paper
and attach it. Step 10
Insert the FPC, 0 1mm
To prevent from the cable Screw
0 2mm Lock Check damage by screw head.
Screw
Tape
Screw Screw
2 5mm
After processing the cables, inserting the FPC and locking,
incline the Audio PCB into the arrow direction.
Connect the FPC
Step 8 Step 11
Step 6
Screw
Sheet Attach Side
Screw 0 1mm
0 1mm
Fix the Ausio PCB Screw Connect the gray antenna cable.
Remove the Release Paper
and attach it.
To prevent from the cable
damage by screw bead.

Cable Process 3/3
Step 12 Step 14
Insert it into the boss.

(Push it downward from the top of boss.)
Connect the brown antenna cable.
Step 13
Cable
Connect the additional cable (black).
9.2.14. Assembling the DU Lid Unit

1. Fix the DU Lid Angle and the DU Lid using the 7 Screws.
<K14-9> <K14-9>
<K14-9> <K14-9>
Screws <K14-9> : DXQT2+D25FNL
<K14-9>
<K14-9>
DIMM Lid Angle
DU Lid

9.2.15. Setting the Rear Cabinet
1. Fix the Rear Cabinet on the Computer using the 13
Screws. <N10> <N10>
<N10> :No.3
2. Close the Lid Covers. :No.11 <N10> <N10>
Note: <N10> :No.9 :No.7
Tighten the Screws in the numbered order (No1 to No13). :No.12
<N10> <N10> <N10>
:No.2 :No.10 :No.5
Screws <N10> : DRHM0061ZA <N10> <N10>
<N10> :No.13 :No.1
:No.6
<N10>
:No.8
<N10>
:No.4
n Cautions for Setting the Rear Cabinet
Match to the circles. 0 to 1mm
Match to the wall. Match to the wall.

0 to 1mm 0 to 1mm
(Note) Arrow without specified measurement: 0 to 0.5 mm 0 1mm
Bottom Case Ass’y

Bottom Rubber
Tape
Potre Blind Sheet
Bottom Rubber
Rated Label
Important Parts
for Safety
Safety critical component

Note for attachment
Avoid running over the frame.
Avoid air leaking into it.
DIMM Thermal Sheet
Match to the marking line and attach it.
Bottom Rubber Bottom Rubber Tape

Bottom Case Assy
9.2.16. Setting the DIMM Lid Ass'y

1. Fix the DIMM Lid Ass'y using the 4 Screws. <K14-8>
<K14-8>
Screws <K14-8> : DRHM5025YAT <K14-8> <K14-8>
<K14-8>
DIMM Lid Ass’y

9.2.17. Setting the Touch Pad and Keyboard
1. Connect the Cable to the Connector (CN800), and attach 7. Set the Keyboard to the computer.
the Touch Pad to the computer.
2. Set the Click Button Plate.
3. Attach the new TP Tape over the Touch Pad.
4. Attach the Palm Rest Ass'y on the computer.
Keyboard 1
Keyboard
FPC 2
TP Tape
Touch Pad
Click Button
Plate Keyboard
8. Fix the KBD Plate using the four Screws. <N9>
KBD Plate
<N9>
<N9> KBD Plate
<N9>
Palm Rest Ass’y
<N9>
Connector Connector
(CN800) (CN18)
5. Connect the Cable of the Keyboard to the Connector

(CN18) on the Main PCB.
6. Fix the KBD Connector Cover using the three Screws.
<N1>
<N1>

KBD
Connector
Cover

n Putting of the Sheet
LCD Cushion Sheet
Ensure it does not come
LCD Cushion Sheet
Ensure it does not come
over the end of the rib. over the end of the rib.
0 0.5mm Gasket E
The paste should be Fit to the wall of the end side, and
put the left side. put the surplus to the Cabinet side.
0 0.5mm
KB CNT Hole Cushion
0 0.5mm KBD Waterproof Sheet C

Match to the circles.
0 to 0.5mm
Avoid coming over.

Avoid coming over.
0 to 0.5 mm
Avoid coming over. 0 to 0.5 mm
Avoid running over. 0 to 0.5 mm
0.5 to 1mm Avoid running over.
Palmrest Waterproof Sheet L 0.5 to 1mm
Attach it using the jig

Palmrest Waterproof Sheet R
Click Button Plate 0 0.5mm
0 0.5mm
Attach it using the jig
0.5 1.5mm
Fold over the front and attach it.

TP Tape Attach it using the jig
Fold over the front and attach it.
Avoid running over other sheets.
Because the sheets described on this page are waterproof sheets,

the whole parts should be put pressure after attaching.
(Especially, put pressure around the sheets.)
*Apply the load to attach.
30 to 40N (3.0 to 4.0Kgf)
n Cautions for Setting the Keyboard

Keyboard Connector Lid Ass’y
Apply the load to attach. 30 to 40N
(3.0 to 4.0 Kgf)
Use the fixing jig
Safety Working
Connect part the LCD CABLE/KBD FFC
Connect the Connector Order of fixing KB Connector Lid

to the dotted part. Screw Screw Screw
Note: Screw Screw Screw Screw Keyboard Connector Lid Sheet
Hold the Connector part when
connecting/disconnecting.
Do not bend at the foot of
stiffening plate.
Do not bend at the foot of
stiffening plate.
Rotate the LCD to make the
KBD FFC insert parts LCD display face front after
Connect the LCD CABLE
Screw setting the KBD.
Screw Screw Screw
Fix from the Hinge side. Screw

Incline to the right.
KBD Connector LID Ass’y Keyboard Plate(L) Screw Fix from the Hinge side.
Avoid running over the Top Case Screw
Connect the KBD FFC

Before setting the KBD
Connect the Keyboard FFC Plate (L) and the KBD
Plate (R), press on the
positions (four) with the
two-sided tapes. Keyboard Plate(R)
30N(3.0Kgf)
After inserting the FFC,

lock the Connector. Keyboard Ass’y
Set using the jig.

n Putting of the Palm Rest ASSY
5 7mm
3 5mm 6 8mm
Windows Logo Label Intel Label
6 8mm
4 6mm
Energy Star Label
Remove the Release Paper, and then attach the Palmrest Assy.
Remove the two-sided tape on the back side and attach it.
After attaching, press by the load 30 to 40N (3.0 to 4.0 Kgf).
Palmrest Assy
Set the five Hooks.
Remove the Release Paper.
n Putting of the KBD Tape
0 to 2 mm from the 0 to 2 mm from

0 to 2 mm from
notch bottom edge the protrusion
the protrusion
0 to 2 mm from
the protrusion
Keyboard
Ensure the direction is right.
KBD Tape KBD Tape

KBD Tape
KBD Tape
0 to 2 mm from
0 to 2 mm from the the protrusion
notch bottom edge
0 to 2 mm from the
notch bottom edge
0 to 2 mm from
the KBD edge

9.2.18. Setting the Battery Pack and the HDD Pack
1. Set the HDD in the HDD Case and fix it using the 2
HDD Case B
Screws. <N13> Hooks
Hooks
HDD FPC
HDD
Heater
<N13>
<N13>
HDD Case A
2. Open the HDD Cover and set the HDD Pack.

3. Open the Battery Cover and set the Battery.
Screws <N13> : DXQT2+D4FNL

1 3
2
HDD Pack
Battery Pack

n Assembly of the HDD ASSY
0 0.5mm Note for the Heater top end location
0 1mm
Avoid any stress

10 15mm
Safety Working Insulation Parts

Insulation Parts
Heater Ass’y
Heater 5 1mm
5 1mm
Heater Assy Back
0
2mm
Sub material: Pet Tape 1 HDD

(19mm width x 4 cm)
Heater Insulation Sheet

Connect the Connector FPC(HDD)
Attach on the inside of 1
Round to make the brown side
outside and insert the notch part
Details for attachment of Heater Insulation Sheet
Thermal Sheet
1 2mm
Two-sided Tape
Come the bottom over by 0 to 0.5 mm.
Attach it on the center of the HDD.

3mm Revision Label Matches to Match to the level.
the center 0 to 1 mm
2mm
Attach on the inner side

of the HDD Case A
HDD Case Lower HDD Case Tab
0 0.5mm
Screw
HDD Case Lower
HDD Connector Guard
Screw
HDD Damper
HDD Case Upper
Production
FPC Connector
Insulation Sheet
Attach Make the Hook inside

Remove the
Release Paper Hook it

9.2.19. Assembling the Each Cover
1. Fix the Battery LID Ass'y, the HDD LID Ass'y, and the
PCMCIA LID Ass'y using the 6 Screws. <K12-16> <N6>:No.6
<N6>:No.5
2. Set the Rear Cabinet. <N6>:No.4
3. Fix the Modem/LAN LID Rubber, the LAN LID Rubber, the <N6>:No.3
<N6>:No.2
USB LID Rubber, the DC IN LID Rubber, the Serial LID DC IN LID Rubber <N6>:No.1
USB LID Rubber
Rubber, the RGB LID Rubber, the Audio LID Rubber and LAN LID Rubber
USB Back Rubber using the 14 Screws. <N6> Moden/LAN LID Rubber
Note: <N6>
Tighten the Screws in the numbered order (No1 to No14). <N6> <N6> :No.12
:No.13 <N6>
:No.14
:No.11 <N6>
Screws <K12-16> : DRQT26+D3FKL <K12-16> <N6> :No.9
<K12-16> :No.10 <N6>
Screw <N6> : DRHM5025YA <K12-16> :No.8
<K12-16> <N6>
:No.7
Serial
LID Rubber
<K12-16>
Battery
LID ASS’Y
HDD LID ASS’Y
Audio
LID Rubber
USB Back
Rubber PCMCIA LID ASS’Y
RGB
LID Rubber

10 Exploded View
K82
A N9
K81 K83
E24 A N9
K3 K30 A N9
K3-1
K31
K3-1-1 K9
K3-1-2 K144
K144
K144
K115 K60
A N1
K144
A N1 A N1
K114
K116
E32 K34
K39
K111
K109
K124
F N11
K107 K113 K100

K5
K110
F N11
K102
K127
K110
K80
K80-8
K80-11
K80-1
K80-9
A N13
K80-6 K80-10
K80-5
K80-7
K80-4
K80-8
Screw tightening torque

K80-3
A 0.2 +
_ 0.02N m
(2.0 +
_ 0.2kgf cm)
F 0.8 +
_ 0.02N m E23
(8.0 +
_ 0.2kgf cm)
K80-2
CF-19CHBAXBM

B K12-15-11
K12-15-4 K12-15-1
K12
K12-15-5
B
K12-15-3
K12-16
B K12-15-11 K12-15-6
K12-14-8
A K12-14-9
K12-15-1 K12-15-2
A K12-14-10 K12-14-2
A
B K12-16 K12-15-9
K12-15-7 A K12-15-10 A K12-14-9
K12-15-8 K112
K12-14-1
A K12-15-9 K12-14-7
B
K12-14-11
K12-15
B K12-16
K12-14-3
K12-10
K12-8 K12-14-6
K12-7
K12-14-1 K12-14-5
K12-9 K12-3 B K12-16 B K12-14-11
K40
E25 K12-14-4
E34
K12-14
K117
E6
K104 C K12-1
K12-2
A N1
B N14 K12-10
E5 K90
K120 K12-12
C K12-1
K12-6
K108
K13
K13-3
K12-13
A K12-13-11 A K12-13-9
K118
B N14
K12-13-2
K13-6 K101 K12-13-8
K13-5 E N18 E N18
K13-4 E8 K103
K13-1 A K12-13-9
K12-5
K13-8 K119 K12-13-7
K49
K41
K13-2 K12-13-1
K12-13-6
K13-7 G N7 K12-13-3 B K12-13-10
C K12-17 K133
K12-4
K12-11 K12-16
K12-13-1
K12-3-5
Screw tightening torque B K12-16 B K12-3-10
A 0.2 +
_ 0.02N m C 0.4 +
_ 0.05N m G 0.4 +
_ 0.02N m
(2.0 _ (4.0 +_ 0.5kgf cm) (4.0 +
_ 0.2kgf cm) K12-3-4
+ 0.2kgf cm)
B 0.3 +
_ 0.03N m E 1.50 +_ 0.15N m
(3.0 _
+ 0.3kgf cm) (15.0 +_ 1.5kgf cm)
CF-19CHBAXBM

K105
K123 H N2
E35
K99
K125
K98
K137 E3
A N9
K44
K141
A K135
N19 K86 A N9
A N19 E26
E1
A
N19
A N9 K87 A E30 K143
N19
K89
K38
K88 K130
K129
K149 K54
E27 A
N9 A N9 K122
A E29 K54
K89 K142 A N9 K91
N9
K131 K121
K51
K47 K56 K136 E11
K46 N19
A N1 A N19
A N19
K93
K140
E33 E2
K138 K95 E13
A N19 K45
E12 K94 A N9
K139 A N8
K50 K95
K96
E9 A N3
E28 K43
E10
A N19 K33
K48 A N9 A N9
A N1
A E20 A N19
K132 A N19 N19
N9 A A N9 A A N9
K37 A N9 N1
E14 A N3 K126
A N4 E7 K92
K35
A N1
A
N9 K15
A N1
A N1
A N9 A N5 K53 K36 A N1
A N5
K22
E4
A N1 Screw tightening torque
A 0.2 +
_ 0.02N m
(2.0 +
_ 0.2kgf cm)
A N1 H 0.4 +
_ 0.02N m
K43 E31 A N1 (4.0 +
_ 0.2kgf cm)
K42
CF-19CHBAXBM

K14
A K14-9
A K14-9 K14-2
K14-5 A
K14-9
K23
K19
K24
K18 K14-3
K21
K17
K14-4
K20
A K32
K27 N6 K26
K54
K32 K25
K14-8
A N6
K16 K14-7 K14-8 K28
A N10 K14-7
A N6
K28
K14-6
A N6
K54
K16
A
N10
A N10
K16
K55 A N10 N10 A N10

A
K14-1
K16
A N10
K14-1-2 A N10 K1
K14-1-1 K85
N6 N6

A 0.2 +
_ 0.02N m
A K14-8 (2.0 +
_ 0.2kgf cm)
A K14-8
K84
CF-19CHBAXBM

K61
K10-4 K62
K10
E36 K61
K10-4-4
K10-4-1
K10-4-3
K10-4-1-1
K10-4-2 K10-4-4
A N1
K29
A N1
K10-4-3 K6
D
K79
N17
K63 K79
K58
K8
K7
K52 D N17
K70 K58
K10-4-5
K10-1-6 K66 K67

K10-1-7
K59
A N1 A K10-1-13
K10-2 K57
E17 K10-3
K59
K59
K10-1-11
K10
-1-5 K10-1-7
K10-1-6 K10-1-9
K10-
1-3
K10-1-3
K10-1-5 A K10-1-13
E16
A N1
K64
K10-1-8
K10-1-4 K10-1-1
K10-1-2 A N1
K10-1-10
K10-1-12 E15
K10-1 E18
K10-1-4 A N1
A 0.2 +
_ 0.02N m
(2.0 +
_ 0.2kgf cm)
D 0.8 +
_ 0.08N m
(8.0 +
_ 0.8kgf cm)
CF-19CHBAXBM

K78
K73
K65
K72
E22
K77
K54
K76
E36 K74 K54

E36-6 E21
A E36-7
E19
E36-5
E36-6
E36-4
E36-1-2 A E36-7
E36-1-1 E36-1
K54
E36-3
E36-9
E36-3
E36-2
K54 E36-8
A E36-7
E36-9
E36-8
E36-11 E36-10
K71
E36-12
E36-11 A E36-7

A 0.18 +
_ 0.02N m
(1.8 +
_ 0.2kgf cm)
CF-19CHBAXBM

K68 C N7 C N7
K69
C N7
C N7
C N7
C N7
C N7
B N15
C N7
K11-9
B
K11-1-3 N15
K11-1-1
K11
K11-1-5 K11-10
B N15
K11-1
K11-1-4 K11-1-3
K11-1-1 D N16
K11-1-2
B N15
K11-8
K11-6
D N16
K11-4 B N15
K11-1-4
K11-5
K11-7
K11-1-5
K11-4
K11-8
K11-1-6
K11-1-2
K11-2 K11-5 C N7
K11-3
K11-2
C N7
K11-3
K68
K11-2

B 0.2 +
_ 0.02N m
(2.0 _
+ 0.2kgf cm) C N7
C 0.3 +
_ 0.03N m
(3.0 +
_ 0.3kgf cm)
C N7
D 0.8 +
_ 0.08N m
(8.0 _
+ 0.8kgf cm)
CF-19CHBAXBM

11 Replacement Parts List
Note : Important Safety Notice
Components identified by ! mark have special characteristics important for safety.
When replacing any of these components, use only manufacturer's specified parts.
CF-19CHBAXBM (2006/12/06)
REF. NO and AREA PART NO. DESCRIPTION Q'TY
Main Block Unit
E1 DL3U11530AAA PCB, MAIN RTL 1
E2 DL3U21530AAA PCB, AUDIO RTL 1
E3 DL3U31530AAA PCB, IO RTL 1
E4 DL3U11550BAA PCB, PAD RTL 1
E5 DL3U21550BAA PCB, SW RTL 1
E6 DL3U31550BAA PCB, LED-LEFT RTL 1
E7 DL3U41550BAA PCB, PR RTL 1
E8 DL3U61550BAA PCB, LED-RIGHT RTL 1
E9 DL3U71550BAA PCB,SD RTL 1
E10 DL3U81550BAA PCB, HSDPA RTL 1
E11 DL3U91550BAA PCB, POWERSW RTL 1
E12 DL3UP1552AAA PCB, EXT ANT UNIT RTL 1
E13 DL3UP1558BAA PCB, BT 2.0 UNIT RTL 1
E14 DL3UP1566AAA BAT FPC UNIT 1
E15 DL3U11553AAA WWAN MAIN ANT 1
E16 DL3U21553AAA WWAN AUX ANT 1
E17 DL3U31553AAA LAN-MAIN BT ANT 1
E18 DL3U41553AAA LAN AUX ANT 1
E19 DL3U11605AAA CF-19 TS PCB 1
E20 DFJS1060ZA WWAN COAXIAL CABLE 1
E21 DFJS1039YA LCD CABLE TS 1
E22 S N0GB1J000018 INVERTER 1
E23 S N3CAYYY00012 HDD 1
E24 N2ABAJ000001 KEYBOARD US 1
E25 DFJS1061ZA MODEM JACK CABLE 1
E26 S N5HAZ0000014 MODEM 1
E27 N5ZZ00000119 PC2-4200 SODIMM 512M INFINEON 1
E28 DFJS1059ZA WLAN COAXIAL CABLE 1
E29 S N5HZC0000019 WIRELESS LAN MODULE 1
E30 D4CZY103A003 THERMISTOR 1
E31 DFJS1043ZA POWER SW CABLE 1
E32 N2EABEC00006 TOUCHPAD 1
E33 BR-2330A/SF LITHIUM COIN BATTERY 1
E34 DFJS1062ZB LAN JACK CABLE 1
E35 K1NB94B00001 EXPRESS PCMCIA COMBO SLOT 1
E36 DFWV08A0089 LCD UNIT ASS'Y 1
E36-1 DL3DW0182AAA LCD ASS'Y 1
E36-1-1 A2CA00000056 LCD BACKLIGHT, CCFL 1
E36-1-2 DFHM0290ZA REFLECTION ANGLE 1
E36-2 DFHR3612ZA LCD PWB SPACER 1
E36-3 DFHR3647YA SPACER SHEET 2
E36-4 DFHR3D92YA LCD BACK DAMPER 1
E36-5 DFHR3570YA LCD BACK CUSHION L 1
E36-6 DFHR3571YA LCD BACK CUSHION S 2
E36-7 DXHM0042ZA SCREW 4
E36-8 DFHR3648ZA HOLDER SHEET B 2
E36-9 DFHR3453YA LCD BACK CUSHION SIDE 3
11-1
E36-10 DFHR3B64ZA LCD SIDE CUSHION A 2
E36-11 DFHR3506YA LCD SIDE CUSHION C 2
E36-12 DFHR3507YA LCD SIDE CUSHION D 1
Accessories
A1 S NCR-B/603A LITHIUM ION BATTERY PACK 1
A2 S CF-AA1633AM1 AC ADAPTOR 1
A3 S K2CG3DR00003 AC CORD 1
A4 S DFQX5624ZA MANUAL(CF-19MK1) 1
A5 DFJS954ZA MODEM CABLE 1
A6 DFHS9017ZA TOUCHPANEL FUKINUNO 1
Packing Material
P1 DFPE0733YA HOLDER 1
P2 DFPE0859YA HOLDER 1
P3 DFPK1210ZA PACKING CASE 1
P4 DFPK1216ZA ACCESSORY BOX 1
Mechanical Parts
K1 DFHM9017ZA-0 EZC LID ASSY 1
K3 DFHR9125ZA-0 PALM REST COVER ASSY 1
K3-1 DFHR9124ZA-0 PALM REST ASSY 1
K3-1-1 DFHR3578ZA ADHESIVE TAPE 1
K3-1-2 DFHR3580YA ADHESIVE TAPE 1
K4 DFQC9006ZB-0 SHOULDER BELT ASSY 1
K5 DFQC9009ZC-0 STRAP BG ASSY 1
K6 S DFKE9059YA LOCK PLATE ASSY 1
K7 DFBH3029VA HINGE 1
K8 DFME0148ZA TETHER 1
K9 S DFKE9086ZA-0 HINGE TOP COVER ASM 1
K10 DFWV80A0366 LCD FRONT CABINET/TS PANEL ASS'Y 1
K10-1 S DFKF9033ZA-0 FRONT CASE ASS'Y 1
K10-1-1 DFJS1064ZA SPEAKER CABLE 1
K10-1-2 L0AA04C00012 SPEAKER 1
K10-1-3 DFHG1634YA-0 LCD CABINET CUSHION A 2
K10-1-4 DFHG1635ZA-0 LCD CABINET CUSHION B 2
K10-1-5 DFHM0319YA LCD ELEPASS 2
K10-1-6 DFHM0321ZA D WASHER 2
K10-1-7 DFHM0322ZA SPRING WASHER 2
K10-1-8 DFHM0413ZA SPEAKER PLATE 1
K10-1-9 DFHR3469ZA PEN FRICTION SHEET 1
K10-1-10 DFHR3E36ZA SPEAKER WP SHEET 1
K10-1-11 DFHR6282ZA PEN HOLDER 1
K10-1-12 DFKM0521ZA-0 FRONT CASE 1
K10-1-13 DRHM5025YAT SCREW 4
K10-2 DFHE0805ZA MAGNET 1
K10-3 DFHP7149ZA MAGNET TAPE 1
K10-4 DFWV84A0276 TOUCH SCREEN PANEL KIT 1
K10-4-1 DL3DV0182AAA TS PANEL ASS'Y 1
K10-4-1-1 DFHR9071ZA PROTECTIVE FILM 1
K10-4-2 DFHR3630ZA TS FPC SPACER 1
K10-4-3 DFHR3476ZA TS SPACER A 2
K10-4-4 DFHR3477ZA TS SPACER B 2
K10-4-5 DFHR3464WA LCD SIDE CUSHION B TS 2
K11 DFWV80C0512 LCD REAR CABINET ASS'Y 1
K11-1 S DFKM9039ZA-0 LCD REAR ASSY 1
K11-1-1 DFHG1634YA-0 LCD CABINET CUSHION A 2
K11-1-2 DFHG1635ZA-0 LCD CABINET CUSHION B 2
K11-1-3 DFHM0319YA LCD ELEPASS 2
11-2
K11-1-4 DFHM0321ZA D WASHER 2
K11-1-5 DFHM0322ZA SPRING WASHER 2
K11-1-6 S DFKM0522ZA-0 REAR CASE 1
K11-2 DFHR3566YA LCD REAR CUSHION F 3
K11-3 DFHR3460YA LCD REAR CUSHION A 2
K11-4 DFHR3567YA LCD REAR CUSHION G 2
K11-5 DFHR3461YA LCD REAR CUSHION B 2
K11-6 DFHR3563YA LCD REAR CUSHION C 2
K11-7 DFHR3564YA LCD REAR CUSHION D 1
K11-8 DFHR3565YA LCD REAR CUSHION E 2
K11-9 DFGB0132ZA-0 TOUGH BOOK BADGE(SILVER) 1
K11-10 DFGB0131ZA-0 PANASONIC BADGE 1
K12 S DFKM9040ZA-0 TOP CASE ASSY 1
K12-1 DFHM0320YA TOP ELEPASS 2
K12-2 DFHR3434ZA AUDIO WATERPROOF SHEET 1
K12-3 DFHR3440ZA DSUB WATERPROOF SHEET 2
K12-4 DFHR3470YA PSW WATERPROOF SHEET 1
K12-5 DFHR3D86ZA FS CASE WP SHEET 1
K12-6 DFHR3D94YA GPS HOLE SHEET A 1
K12-7 DFHR3E15ZA LAN WP SHEET 1
K12-8 DFHR3E16ZA MODEM WP SHEET 1
K12-9 DFHR3F00ZA 1394 WP SHEET 1
K12-10 DFHR3F01ZA USB BACK WP SHEET 2
K12-11 DFHR6276ZA-0 POWER SW KNOB 1
K12-12 S DFKM0519ZA-0 TOP CASE 1
K12-13 S DFKE9089ZA-0 BAT LID ASSY 1
K12-13-1 DFBH3030ZA LID HINGE 2
K12-13-2 DFHM0315YC LATCH PLATE BATTERY 1
K12-13-3 DFHR3466YA LID KNOB SHEET 1
K12-13-4 DFHR3509YA BAT COVER SHEET 1
K12-13-5 S DFKE0889ZA-0 LID KNOB 1
K12-13-6 S DFKE0891ZA-0 BAT LID 1
K12-13-7 DFUN0068XA LID KNOB SPRING 1
K12-13-8 DFUS0292ZB LID KNOB SPRING PLATE 1
K12-13-9 DRHM0109ZAT SCREW 2
K12-13-10 DRQT26+D3KLT SCREW 2
K12-13-11 DXQT2+F3FNLT SCREW 1
K12-14 S DFKE9090ZA-0 HDD LID ASSY 1
K12-14-2 DFHM0285XC LID LATCH PLATE 1
K12-14-4 DFHR3508YA-0 HDD COVER SHEET 1
K12-14-6 S DFKE0890ZA-0 HDD LID 1
K12-15 S DFKE9091ZA-0 PCMCIA LID ASSY 1
K12-15-2 DFHM0285XC LID LATCH PLATE 1
K12-15-4 DFHR3588WA-0 PCMCIA COVER SHEET SD 1
K12-15-6 S DFKE0890ZA-0 HDD LID 1
K12-15-9 DRHM0109ZAT SCREW 2
K12-15-10 DRHM5025YAT SCREW 1
K12-15-11 DRQT26+D3KLT SCREW 2
K12-16 DRQT26+D3KLT SCREW 6
11-3
K12-17 DXQT3+F4FNLT SCREW 2
K13 S DFKE9092ZA-0 TABLET LATCH ASSY 1
K13-1 DFHG1669ZA TABLET LATCH SHEET 1
K13-2 DFHM0291ZA TABLET LATCH PLATE 1
K13-3 DFHM0294WA TABLET LATCH PIN 2
K13-4 DFHM0295ZA TABLET LATCH SHAFT 1
K13-5 S DFKE0892ZA-0 TABLET LATCH KNOB 1
K13-6 S DFKE0893ZA-0 TABLET LATCH LEVER 1
K13-7 DFNW1604ZA CUT WASHER 1
K13-8 DFUN0069XA LATCH KNOB SPRING 1
K14 S DFKM9041ZA-0 BOTTOM CASE ASSY 1
K14-1 DFHM9016ZA-0 DIMM LID ASSY 1
K14-1-1 DFHM0401ZA-0 DIMM LID 1
K14-1-2 DFHR3E14ZA DIMM LID WP SHEET 1
K14-2 DFHM0410ZA DU LID ANGLE 1
K14-3 DFHR3441ZA DU LID WATERPROOF SHEET 1
K14-4 DFHR3F64ZA HDD BOTTOM SHEET 2
K14-5 DFHR6283ZA-0 DU LID 1
K14-6 S DFKM0518ZA-0 BOTTOM CASE 1
K14-7 DFUS0316ZA PLATE SPRING GUIDE PIN 2
K14-8 DRHM5025YAT SCREW 6
K14-9 DXQT2+D25FNL SCREW 7
K15 DFHE1019YA DU CONNECTOR SPONGE 1
K16 DFHG1209ZA RUBER FOOT 4
K17 DFHG1633ZB-0 SERIAL LID RUBBER 1
K18 DFHG1638ZA-0 MODELAN LID RUBBER 1
K19 DFHG1639ZA-0 USB LID RUBBER 1
K20 DFHG1641ZB-0 RGB LID RUBBER 1
K21 DFHG1660ZA-0 LAN LID RUBBER 1
K22 DFHG1790ZA BAT CUSHION 1
K23 DFHG1902ZA-0 DC-IN LID RUBBER 1
K24 DFHG1903ZA-0 1394 LID RUBBER 1
K25 DFHG1906ZA-0 AUDIO LID RUBBER 1
K26 DFHG1907YA-0 USB LID RUBBER 2 1
K27 DFHM0286YB LID RUBBER PLATE A 1
K28 DFHM0288ZB LID RUBBER PLATE C 2
K29 DFHM0296XA-0 LCD HINGE COVER(SILVER) 1
K30 DFHM0302XA-2 KEYBOARD PLATE(L) CF-19 1
K31 DFHM0303XA-0 KEYBOARD PLATE(R) 1
K32 DFHM0311ZB LID RUBBER PLATE B 2
K33 DFHM0403ZA DU CNT ANGLE 1
K34 DFHM0406ZA KBD CNT LID 1
K35 DFHM0407ZA BAT CON ANGLE 1
K36 DFHR3445ZA HEAT DISSIPATION RUBBER 2
K37 DFHR3487YA PORTRE SHEET 1
K38 DFHR3636ZA CABLE HOLD SHEET 1
K39 DFHR3D91ZA KB CNT LID WP SHEET 1
K40 DFHR3E03ZA SD BLIND SHEET 1
K41 DFHR3E53ZA FS SCREW SHEET 1
K42 DFHR3F62ZA POWER SWITCH CABLE SHEET 1
K43 DFHR3G19ZA INSULATION SHEET 2
K44 DFHR3G22ZA PCMCIA SIDE SHEET 1
K45 DFHR6246ZA HDD GUIDE 1
K46 DFHR6284ZA DIMM HOLDER 1
K47 DFHR6286ZA-0 RF SW KNOB 1
K48 DFHR6289ZA BAT CON HOLDER 1
K49 DFHR6290ZA-0 FS DUMMY CASE 1
K50 DFHR6312ZA ANT CABLE HOLDER 1
K51 DFHR7946ZA MP GUIDE SHEET 1
11-4
K52 DFHR9081ZA PEN 1
K53 DFMC0870ZA DU CONN SPRING PLATE 1
K54 DFMX0383TA INSULATION PARTS 17
K55 DFMY0419ZA DIMM THERMAL RUBBER 1
K56 DFMY0444YA THERMAL RUBBER 1
K57 DFHE0915ZA EMI SHEET 10X20 1
K58 DFHM0325ZA CABLE HOLD PLATE 2
K59 DFHR3432ZA ANT CABLE CUSHION 4
K60 DFHR3516ZA PROTECT SHEET(SCREW) 1
K61 DFHR3573YA LCD SIDE CUSHION E 2
K62 DFHR3574YA LCD SIDE CUSHION F 1
K63 DFHR3638XA DG TAPE 1
K64 DFHR3E21ZA ANT DROP CUSHION 2 1
K65 DFHR3G16ZA INSULATION SHEET 30X140 1
K66 DFHR3G42ZA TAPE PEN HOLDER 1
K67 DFHR6081ZA-0 CABLE HOLDER 2
K68 DFHR6105XA-2 ANT COVER 2
K69 DFHR6279ZA-0 TABLET LATCH COVER 1
K70 DFHR6298ZA HINGE CABLE HOLDER 1
K71 DFMC0685ZA CONDUCTIVE SHEET, LCD 1
K72 DFMC0816ZA INV MIL SHEET 1
K73 DFMC0877YA INVERTER CASE 1
K74 DFMC0878ZA INVERTER SHIELD SHEET 1
K76 DFMX1267ZA INVERTER CASE(BASE) 1
K77 DFMX1268ZA INVERTER CASE(LOWER) 1
K78 DFQT6077YA CAUTION LABEL, LCD 1
K79 DFUQ0100ZA LOCK SPRING 2
K80 DFWV99A0113 HDD MOUNTING KIT 1
K80-1 DFHM0404ZA HDD CASE UPPER 1
K80-2 DFHM0416ZA HDD CASE LOWER 1
K80-3 DFHR3589ZA HDD CASE TAB 1
K80-4 DFHR3D89ZA HDD DAMPER 1
K80-5 DFHR3F54ZA HDD CON SHEET 1
K80-6 DFHR6297ZA HDD CONNECTOR GUARD 1
K80-7 DL3UP1564AAA HDD FPC UNIT 1
K80-8 DFMX0383TA INSULATION PARTS 2
K80-9 DFMX1265ZA INSULATION SHEET(HDD HEATER) 1
K80-10 DFMY3208ZA THERMAL SHEET 1
K80-11 S L9DZYY000008 HEATER(HDD) 1
K81 DFQT0045ZA ENERGY STAR LABEL 1
K82 DFQT0046ZA VISTA CAPABLE LABEL 1
K83 DFQT9981ZA CENTRINO DUO LABEL 1
K84 DFQX3999XA OVERLAMINATE-LARGE 1
K85 S DFGT1094ZA RATED LABEL 1
K86 DFHD04H004YB HEXAGON SPACER H=4.2MM 2
K87 DFHR3F85ZA MODEM CABLE SHEET 1
K88 DFMC0881ZA BUSTERAID MODEM 2
K89 DFMY3235ZA THERMAL DIFFUSION SHEET 2
K90 DFHM0309YA-1 SIM LOCK PLATE 1
K91 DFHR3G18ZA BIS HEAD SHEET 1
K92 DFHR3G24ZA BIS HEAD SHEET 2 1
K93 DFMY3224ZA WLAN SHEET 1
K94 DFHM0412ZA RF-BT PLATE 1
K95 DFHR3154ZA LCD CABLE TAPE 2
K96 DFHR5484ZA CLAMP 1
K98 DFHE0326XA GASKET-65TSV10-4-15 1
K99 DFHE0811YA GASKET-65TSV4-3-50 1
K100 DFHE1031ZA GASKET-65TSV13-1.5-20 1
K101 DFHG1962ZA POWER SPRING SHEET 1
11-5
K102 DFHP7200ZA ADHENSIVE TAPE 1
K103 DFHP7256ZA RF LED PWB TAPE 1
K104 DFHP7257ZA LED PWB TAPE 1
K105 DFHP7279ZA USB SCREW COVER ADHESIVE 1
K106 DFHR3049ZA LCD DAMPER E 1
K107 DFHR3438ZA CLICK BUTTON SHEET 1
K108 DFHR3483SA OPERATION SHEET 1
K109 DFHR3583YA KB WP SHEET 1
K110 DFHR3642YA LCD CUSHION SHEET 2
K111 DFHR3643ZA TP BOTTOM TAPE 1
K112 DFHR3655YA HDD CASE SPACER 2
K113 DFHR3D90ZA KB CNT HOLE CUSHION 1
K114 DFHR3D93ZA TP WP SHEET 1
K115 DFHR3D97ZA LED PWB TAPE 1
K116 DFHR3E02ZA PALM REST WP SHEET R 1
K117 DFHR3E19ZA LED SYAKOU SHEET 1
K118 DFHR3E34ZA RF SYAKOU SHEET 1
K119 DFHR3F45ZA BATTERY CUSHION 1
K120 DFHR3F55ZA OPERATION TAPE 1
K121 DFHR3F65ZA PC SHEET 2
K122 DFHR3F66ZB PET SHEET 2
K123 DFHR3G40ZA USB SCREW COVER SPACER 1
K124 DFHR6044XA CLICK BUTTON PLATE 1
K125 DFHR6326ZA USB SCREW COVER 1
K126 DFMD2182ZA PLATE HEAT PIPE 1
K127 DFMD3125ZA BACK PLATE KENSINGTON 2 1
K129 DFMY0278YA THERMAL SHEET 1
K130 DFMY0447ZA CPU HEAT PIPE RUBBER 1
K131 DFMY3208ZA WLAN SHEET 1
K132 DFMY5039ZA HEAT PIPE UNIT 1
K133 DFUQ0111ZA POWER SW SPRING 1
K135 DFHR3591ZB INSU SHEET CHIP SET 1
K136 DFHR3F61YA COIN BATTERY FOOT SHEET 1
K137 DFMY3234ZA THERMAL DIFFUSION SHEET 1
K138 DFHR7518ZA H CABLE SHEET 1
K139 DFMX1277ZA INSULATION SHEET 1
K140 DFHR3488ZA ANTENNA SHEET 1
K141 DFHG429YA IO DC TUBE 1
K142 DFHR3G38ZA DIMM CUSHION 2
K143 DFHR3G39ZA USB SCREW SPACER 1
K144 DFHP7270ZA KB ADHESIVE TAPE 4
N1 DFHE5025XA SCREW 33
N2 DFHE5058ZB SCREW 4
N3 DFHE5108ZA SCREW 4
N4 DRHM0112ZA SCREW 2
N6 DRHM5025YA SCREW 18
N7 DRQT26+E5FKL SCREW 18
N8 DRSB2+10FKL SCREW 2
N9 DRSB2+5FKL SCREW 27
N11 DRYN3+J6FKL SCREW 2
N13 DXQT2+D4FNL SCREW 2
N14 DXQT3+D4FKNL SCREW 2
N15 DXYN2+J6FNL SCREW 10
N19 XSB2+3FNL SCREW 17
11-6
Replacement Parts List
Note: Important Safety Notice
Components identified by ! mark have special characteristics important for safety.
When replacing any of these components use only manufacturer's specified parts.
CF-19CHBAXBM (2006/11/20)
REF. NO and AREA PART NO. DESCRIPTION Q'TY
MAIN PCB
C 1, 2, 3, 6, 7, 8, 10, 11, 12, F1J0J106A016 CAPACITOR, 6.3V, 10µF 64
14, 15, 16, 18, 19, 20, 22,
23, 24, 27, 28, 29, 30, 31,
32, 33, 34, 35, 36, 37, 38,
39, 40, 43, 51, 52, 55, 59,
60, 62, 96, 98, 100, 102,
111, 113, 115, 117, 146,
176, 229, 257, 258, 260,
265, 266, 267, 274, 276,
C 4, 53, 57, 83, 151, 155 EEFCX0D221R CAPACITOR, 2V, 220µF 6
C 5, 9, 13, 17, 21, 25, 45, 46, F1G1C104A042 CAPACITOR, 16V, 0.1µF 149
47, 48, 49, 50, 54, 56, 58,
61, 63, 64, 65, 66, 67, 68,
69, 70, 71, 73, 80, 84, 90,
91, 92, 93, 97, 99, 101,
103, 106, 107, 108, 109,
112, 114, 116, 118, 140,
141, 142, 145, 147, 148,
150, 152, 153, 157, 158,
159, 160, 161, 162, 163,
164, 165, 166, 167, 168,
169, 170, 171, 172, 173,
174, 175, 177, 178, 186,
197, 203, 204, 214, 215,
216, 223, 224, 226, 227,
228, 230, 233, 237, 244,
247, 259, 264, 271, 272,
273, 275, 278, 281, 282,
286, 288, 294, 295, 296,
303, 304, 312, 315, 316,
321, 322, 323, 324, 325,
326, 327, 328, 339, 341,
344, 345, 346, 347, 351,
352, 354, 356, 357, 358,
C 41, 74, 75, 82, 120, 121, F1J0J4750019 CAPACITOR, 6.3V, 4.7µF 10
194, 196, 240, 314
C 44, 350, 612, 678, 681, 686 F1G1H1010005 CAPACITOR, 50V, 100pF 6
C 72, 76, 77, 78, 79, 81, 85, F1H0J1050022 CAPACITOR, 6.3V, 1µF 18
88, 95, 104, 119, 126, 127,
128, 129, 277, 279, 353
C 86, 87, 143, 154, 156, 184, F1H1A1050015 CAPACITOR, 10V, 1µF 20
187, 189, 225, 231, 249,
250, 253, 254, 255, 256,
603, 690, 698, 799
C 122, 123, 124, 125, 144, F1G1E103A062 CAPACITOR, 25V, 0.01µF 29
149, 179, 180, 181, 182,
188, 191, 192, 193, 207,
217, 218, 219, 222, 236,
245, 263, 268, 269, 305,
C 130, 131 F1G1H180A542 CAPACITOR, 50V, 18pF 2
C 136, 137, 138, 139, 290, F1G1A104A014 CAPACITOR, 10V, 0.1µF 7
291, 292
C 183, 185 F1G1H6R0A544 CAPACITOR, 50V, 6.0pF 2
C 198 EEFUD0J151ER CAPACITOR, 6.3V, 150µF 1
11-7
C 200, 235, 289, 293, 297, F1G1H102A496 CAPACITOR, 50V, 1000pF 22
302, 340, 342, 343, 616,
623, 639, 641, 643, 659,
677, 679, 680, 684, 802,
C 243, 804 F1J1E334A081 CAPACITOR, 25V, 0.33µF 2
C 246 F1G1H271A495 CAPACITOR, 50V, 270pF 1
6
C 283, 285 F1G1H7R0A544 CAPACITOR, 50V, 7.0pF 2
C 287 F1L3D102A003 CAPACITOR, 2000V, 1000pF 1
C 299, 606, 613, 615, 622, F1H1H104A748 CAPACITOR, 50V, 0.1µF 14
644, 658, 673, 676, 694,
695, 697, 699, 700
C 317, 318, 319, 320, 604 F1J1E105A009 CAPACITOR, 25V, 1µF 5
C 335, 338 F1G1A683A014 CAPACITOR, 10V, 0.068µF 2
C 431, 650, 651, 652, 806 EEFSX0D331ER CAPACITOR, 2V, 330µF 5
C 608, 609 EEFCX0J101R CAPACITOR, 6.3V, 100µF 2
C 611, 626, 648, 649, 654, F1L1E106A017 CAPACITOR, 25V, 10µF 8
672, 687, 808
C 614, 624, 820, 821, 822, F1H1H103A748 CAPACITOR, 50V, 0.01µF 8
823, 824, 825
C 618, 657, 661 F1G1H471A496 CAPACITOR, 50V, 470pF 3
C 621, 640, 646, 664, 682, F1J0J475A009 CAPACITOR, 6.3V, 4.7µF 6
C 691
627 EEFCX0G151R CAPACITOR, 2V, 150µF 1
C 632, 633, 634 F1G1C473A004 CAPACITOR, 16V, 0.047µF 3
C 645 F1H1H222A748 CAPACITOR, 50V, 2200pF 1
C 653, 671, 693 EEFCD0D101ER CAPACITOR, 2V, 100µF 3
C 655, 683 F1H1C224A074 CAPACITOR, 16V, 0.22µF 2
C 685 F1H1E472A050 CAPACITOR, 25V, 4700pF 1
C 688 EEFCD0D151ER CAPACITOR, 2V, 150µF 1
C 701, 702, 703, 705 F1K1E1060001 CAPACITOR, 25V, 10µF 4
C 704 EEFCD0J470ER CAPACITOR, 6.3V, 47µF 1
C 807 F1H1H1830001 CAPACITOR, 50V, 0.018µF 1
CF 1, 2, 3 D4CC1103A038 THERMISTOR 3
CN 2 K1MYL0B00003 CONNECTOR 1
CN 3, 904 K1KA02BA0014 CONNECTOR 2
CN 4 K1NAF0D00003 CONNECTOR 1
CN 5 K1KY42B00001 CONNECTOR 1
CN 6 K1FY104BA024 CONNECTOR, USB 1
CN 8 K1KA20AA0261 CONNECTOR 1
CN 9 K1MN24BA0133 CONNECTOR 1
CN 10 K1MYL0B00004 CONNECTOR 1
CN 11 K1MY52BA0190 CONNECTOR 1
CN 14 K1KA02B00292 CONNECTOR 1
CN 15 K1MN30AA0058 CONNECTOR 1
CN 17 K1KA20AA0184 CONNECTOR, BATT CABLE 1
CN 20 K1MY04AA0041 CONNECTOR 1
11-8
CN 22 K2HZ104B0014 CONNECTOR 1
CN 23 K1MY40A00001 CONNECTOR 1
CN 24 K1KY12A00005 CONNECTOR 1
CN 25 K1KYA0A00019 CONNECTOR 1
CN 27 K1MN40B00048 CONNECTOR 1
D 1, 2, 3, 8 MA2J72900L DIODE 4
D4 B0JDBE000002 DIODE 1
D 5, 600 B0JCPD000023 DIODE 2
D6 B0KB00000044 DIODE 1
D 9, 10, 11 MA3J14700L DIODE 3
D 601, 602, 603 B0ADDH000004 DIODE 3
D 604 MAZ81200ML DIODE 1
D 606, 622 MA3S132E0L DIODE 2
D 608 B0JCQD000001 DIODE 1
D 609, 611, 626, 629, 631, B0JCMD000014 DIODE 6
D 632
610, 627, 630 B0JDAE000004 DIODE 3
D 612, 613, 615, 617, 618 MAZ80510ML DIODE 5
D 619, 621 MA2S111-TX DIODE 2
D 620 B2ABAM000002 DIODE 1
D 624 DEDRB081L20 DIODE 1
F1 S K5H502Z00003 FUSE, 5A, 32V 1
F 2, 3, 4, 5, 8 S K5H202Z00005 FUSE, 2A, 32V 5
F 10, 800 S K5H802300002 FUSE, 8A, 72V 2
F 11 S K5H103300003 FUSE, 10A, 72V 1
IC 1 C2GBC0000314 CPU 1
IC 2 C1CB00002360 IC, CHIPSET 1
IC 3 C0JBZZ000388 IC, CLOCK GENERATOR 1
IC 4 C1DB00001541 IC, CHIPSET 1
IC 5 C1CB00002585 IC 1
IC 6 C1DB00001182 IC, LAN CONTROLLER 1
IC 7 C3EBCG000100 IC, EEPROM 1
IC 8 C1DB00001159 IC, PERIPHERAL LSI 1
IC 9 C0CBCBC00137 IC, REGULATOR 1
IC 10 C1CB00002540 IC, TEMPERATURE CENSOR IC 1
IC 11 C0DBZYY00017 IC 1
IC 12, 19 C0DBZYY00026 IC, USB POWER SW 2
IC 14 C0DBZYY00019 IC, POWER MANAGEMENT SWITCH 1
IC 15 C3EBDY000005 IC, EEPROM 1
IC 16 C0DBZYY00016 IC 1
IC 18, 32, 34, 35 C0JBAZ002422 IC, FET SWITCH 4
IC 20 C0ZBZ0000978 IC 1
IC 21, 22 C0JBAS000218 IC, LOGIC 2
IC 23, 24, 25 C0EBE0000460 IC 3
IC 26 C0EBH0000457 IC 1
IC 27 C2CBJA000003 IC, MICON 1
IC 30 C3FBLY000024 IC, SPI FLASH MEMORY 1
IC 31 C1CB00002268 IC, SECURITY CHIP 1
IC 33, 51, 52, 59 C0JBAA000348 IC, 1 GATE LOGIC 4
IC 41, 58 C0JBAE000306 IC, 2
IC 42 C1CB00002264 IC 1
IC 46 C0JBAA000362 IC, LOGIC 1
IC 50 C0JBAB000832 IC, LOGIC 1
IC 53 C0JBAC000363 GATE LOGIC 1
IC 54 C0JBAC000367 IC, LOGIC 1
IC 55, 56, 57, 800 C0JBAA000347 IC, 1 GATE LOGIC 4
11-9
IC 600 C0ABZA000047 IC, AMP 1
IC 601 C0ABBA000093 IC, OP AMP 1
IC 602 C0DBAYY00194 IC, DC/DC 1
IC 603 C0JBAD000236 IC, LOGIC 1
IC 604 C0JBAB000622 IC, 1 GATE LOGIC 1
IC 605 C0DBEFH00002 IC, REGULATOR 1
IC 606 C0CBCAC00161 IC 1
IC 607 C0EBE0000333 IC 1
IC 608 C0DBDJH00009 IC, LINER 1
IC 610, 611, 612 C0DBALH00003 IC 3
L 1, 3 G1C1R0MA0076 INDUCTOR 2
L2 G1C91NM00001 INDUCTOR 1
L 4, 906 J0JJC0000015 INDUCTOR 2
L 6, 11, 12, 18, 19, 20, 21, J0MAB0000200 INDUCTOR 9
25, 27
L 7, 10, 26 J0JHC0000074 INDUCTOR 3
L 13, 14, 15, 24 J0JDC0000045 INDUCTOR 4
L 600 DDAZS100MT3T INDUCTOR 1
L 601 G1C100MA0106 INDUCTOR 1
L 602 G1CR56ZA0140 INDUCTOR 1
L 603 G1C2R8MA0022 INDUCTOR 1
L 605 G1C4R7MA0106 INDUCTOR 1
L 606 G1C4R7Z00013 INDUCTOR 1
L 607 G1A160H00001 INDUCTOR 1
PA 1, 2 S D4FB1R100009 SWITCH 2
Q 1, 2, 644, 802 B1CFGD000023 TRANSISTOR 4
Q 3, 22, 24, 36, 37, 607, 612 B1GBCFNN0042 TRANSISTOR 7
Q 4, 39 B1GDCFNN0031 TRANSISTOR 2
Q 5, 8 B1MBDCA00004 TRANSISTOR 2
Q 6, 13, 20, 29, 40, 641, 642, B1GBCFJN0037 TRANSISTOR 11
643, 646, 801, 804
Q 9, 10, 11, 21, 26, 28, 31, B1DHDC000028 TRANSISTOR 9
33, 625
Q 12, 14, 15, 17, 18, 19 B1MBBCA00003 TRANSISTOR 6
Q 25, 27, 32, 617, 618, 619, XP0421300L TRANSISTOR 9
621, 623, 626
Q 30 B1DHFD000015 TRANSISTOR 1
Q 34, 35 B1CFFB000001 TRANSISTOR 2
Q 600, 601, 602 XP0421400L TRANSISTOR 3
Q 603, 604, 606 B1CHRD000001 TRANSISTOR 3
Q 608, 634, 638 B1CFGD000003 TRANSISTOR 3
Q 609, 610, 637 B1MBEDA00017 TRANSISTOR 3
Q 616, 622 B1CHRC000009 FET 2
Q 631, 633, 639, 640, 800 B1DBGD000006 TRANSISTOR 5
Q 632, 803 B1DFGD000032 TRANSISTOR 2
Q 645 B1MBEDA00008 TRANSISTOR 1
R 1, 2, 24, 25, 38, 42, 43, ERJ2GEJ102X RESISTOR, 1/16W, 1KΩ 16
140, 141, 179, 180, 281,
283, 305, 306, 437
R3 D1H85104A024 RESISTOR ARRAY 1
R 7, 8, 28, 30, 36 ERJ2RKF1000X RESISTOR, 1/16W, 100Ω 5
R 9, 676, 685 ERJ2RKF1001X RESISTOR, 1/16W, 1KΩ 3
R 10 ERJ2RKF2001X RESISTOR, 1/16W, 2KΩ 1
R 12 ERJ2RKF51R0X RESISTOR, 1/16W, 51Ω 1
R 13, 15 ERJ2RKF27R4X RESISTOR, 1/16W, 27.4Ω 2
R 14, 16, 31, 32 ERJ2RKF54R9X RESISTOR, 1/16W, 54.9Ω 4
R 19, 21 ERJ2GEJ560X RESISTOR, 1/16W, 56Ω 2
R 20, 636, 712, 731 ERJ3GEYJ100V RESISTOR, 1/16W, 10Ω 4
11-10
R 23 ERJ2GEJ240X RESISTOR, 1/16W, 24Ω 1
R 26, 266, 609, 612, 613, 749 ERJ2GEJ562X RESISTOR, 1/16W, 5.6KΩ 6
R 27, 29 ERJ2RKF2210X RESISTOR, 1/16W, 221Ω 2
R 33, 34, 78, 132, 167 ERJ2RKF24R9X RESISTOR, 1/16W, 24.9Ω 5
R 37 ERJ2RKF2000X RESISTOR, 1/16W, 200Ω 1
R 45, 80, 96, 139, 142, 143, ERJ2GEJ103X RESISTOR, 1/16W, 10KΩ 47
149, 156, 173, 182, 197,
206, 207, 210, 223, 226,
229, 230, 233, 282, 287,
292, 293, 294, 298, 299,
319, 331, 339, 341, 343,
345, 347, 355, 356, 431,
432, 615, 635, 641, 695,
R 47, 97, 126, 128, 145, 146, ERJ2GE0R00X RESISTOR, 1/16W, 0Ω 33
154, 161, 224, 240, 241,
265, 313, 320, 333, 349,
442, 443, 445, 604, 673,
674, 689, 693, 697, 699,
703, 706, 800, 812, 813,
R 58, 107, 148, 171, 195, ERJ2GEJ101X RESISTOR, 1/16W, 100Ω 22
196, 216, 262, 272, 314,
315, 316, 350, 602, 603,
657, 658, 662, 663, 664,
R 66, 67 ERJ2RKF80R6X RESISTOR, 1/16W, 80.6Ω 2
R 70, 71, 121, 289, 330, 337, ERJ2GEJ330X RESISTOR, 1/16W, 33Ω 7
344
R 72, 93, 101, 122, 124, 150, D1H81034A024 RESISTOR ARRAY 9
307, 325, 326
R 73 ERJ2RKF1501X RESISTOR, 1/16W, 1.5KΩ 1
R 79 ERJ3GEYJ220V RESISTOR, 1/16W, 22Ω 1
R 81, 82, 84, 85, 86, 88 D1HA56080001 RESISTOR ARRAY 6
R 83, 87, 242 D1H85604A024 RESISTOR ARRAY 3
R 89, 90, 91, 92, 152 ERJ2GEJ1R0X RESISTOR, 1/16W, 1Ω 5
R 95, 221 D1H83304A024 RESISTOR ARRAY 2
646, 708, 709, 727, 728,
R 119, 159, 184, 186, 187, ERJ2GEJ104X RESISTOR, 1/16W, 100KΩ 31
188, 189, 190, 193, 194,
208, 209, 212, 213, 219,
227, 238, 256, 258, 261,
277, 278, 279, 280, 617,
619, 620, 621, 654, 656,
R 120 D1H84724A024 RESISTOR ARRAY 1
R 123, 174, 175, 176, 177, DEARA8AJ103M RESISTOR ARRAY 17
286, 300, 301, 302, 303,
304, 308, 309, 321, 322,
R 133 ERJ2RKF22R6X RESISTOR, 1/16W, 22.6Ω 1
R 144, 203, 686 ERJ2GEJ471X RESISTOR, 1/16W, 470Ω 3
R 157, 757 ERJ2GEJ472X RESISTOR, 1/16W, 4.7KΩ 2
R 162 ERJ2GEJ203X RESISTOR, 1/16W, 20KΩ 1
R 163 ERJ2GEJ106X RESISTOR, 1/16W, 10MΩ 1
R 164, 271, 618, 660 ERJ2GEJ105X RESISTOR, 1/16W, 1MΩ 4
R 169, 257 ERJ2GEJ334X RESISTOR, 1/16W, 330KΩ 2
R 178, 220 D1H82204A024 RESISTOR, 1/16W, 22Ω 2
205, 351, 352, 353, 799
R 243 ERJ2GEJ512X RESISTOR, 1/16W, 5.1KΩ 1
R 264 ERJ2RHD562X RESISTOR, 1/16W, 5.6KΩ 1
11-11
R 267, 268, 269, 270 ERJ2RKF49R9X RESISTOR, 1/16W, 49.9Ω 4
R 273 EXBV8V750JV RESISTOR ARRAY 1
36 285
R 284, D1H81024A024 RESISTOR ARRAY 2
R 311, 317, 436 ERJ2RKF3901X RESISTOR, 1/16W, 3.9KΩ 3
R 430, 700, 803, 804 ERJ3GEY0R00V RESISTOR, 1/16W, 0Ω 4
R 601 D1ZZ00000046 RESISTOR, 1W, 5mΩ 1
R 605, 608 ERJ2RHD103X RESISTOR, 1/16W, 10KΩ 2
R 607, 610 ERJ2RKF1503X RESISTOR, 1/16W, 150KΩ 2
R 614 ERJ3GEYJ3R3V RESISTOR, 1/16W, 3.3Ω 1
R 616, 630, 670 ERJ2GEJ473X RESISTOR, 1/16W, 47KΩ 3
R 622, 623 D1BDR1000002 RESISTOR, 1/8W, 0.1Ω 2
R 624 D1BDR0680001 RESISTOR, 1/8W, 0.068Ω 1
R 628, 629, 704, 705, 726, D1BDR0220001 RESISTOR, 1/8W, 0.022Ω 7
743, 801
R 631, 741, 747, 802, 810 ERJ2GEJ474X RESISTOR, 1/16W, 470KΩ 5
R 634, 710, 729 ERJ2GEJ153X RESISTOR, 1/16W, 15KΩ 3
R 637 ERA3YEB622V RESISTOR, 1/16W, 6.2KΩ 1
R 638, 754, 755 ERA3YKB104V RESISTOR, 1/16W, 100KΩ 3
R 639, 733 ERA3YEB203V RESISTOR, 1/16W, 20KΩ 2
R 642 ERA3YEB303V RESISTOR, 1/16W, 30KΩ 1
R 644 ERA3YEB471V RESISTOR, 1/16W, 470Ω 1
R 647, 648, 725, 742, 744, D1BDR0330001 RESISTOR, 1/8W, 0.033Ω 6
8
R 655 ERJ2GEJ225X RESISTOR, 1/16W, 2.2MΩ 1
R 667, 807 ERJ6GEYJ122V RESISTOR, 1/10W, 1.2KΩ 2
R 668, 669 ERJ6GEYJ222V RESISTOR, 1/10W, 2.2KΩ 2
R 684, 690, 696 ERJ3GEYJ1R0V RESISTOR, 1/16W, 1Ω 3
R 692, 922 ERJ2RKF5101X RESISTOR, 1/16W, 5.1KΩ 2
R 701 D1ZZ00000093 RESISTOR, 1W, 1mΩ 1
R 732 ERA3YEB621V RESISTOR, 1/16W, 620Ω 1
R 738 ERJ2RHD123X RESISTOR, 1/16W, 12KΩ 1
R 746 ERJ2RKD114X RESISTOR, 1/16W, 110KΩ 1
R 751, 752 ERJ2RHD302X RESISTOR, 1/16W, 3KΩ 2
R 806 ERJ3GEYJ562V RESISTOR, 1/16W, 5.6KΩ 1
SW 2 K0D112B00071 SW 1
T1 G5BYC0000015 TRANCE 1
11-12
X1 H0J143500058 OSCILLATOR, 14.318MHz 1
X2 H0J327200115 OSCILLATOR, 32.768KHz 1
X3 H0J245500083 XTAL 1
X4 H0J250500076 XTAL 1
X5 H2D800400015 OSCILLATOR, 8MHz 1
ZA 1, 2, 5, 6, 7, 10, 11 K1YGZZ000060 SPACER 7
AUDIO PCB
C 900, 905, 910, 942, 943, F1H1A1050015 CAPACITOR, 10V, 1µF 7
944, 945
C 901, 902, 903, 907, 908, F1G0J224A001 CAPACITOR, 6.3V, 0.22µF 11
912, 915, 918, 919, 929,
C 906 F1J0J4750019 CAPACITOR, 6.3V, 4.7µF 1
C 909 F1G1E103A062 CAPACITOR, 25V, 0.01µF 1
C 911, 922, 934, 935, 936, F1J0J106A016 CAPACITOR, 6.3V, 10µF 7
938, 939
C 914, 920, 921, 937 F1G1C104A042 CAPACITOR, 16V, 0.1µF 4
C 926, 931, 947 F1G1H1010005 CAPACITOR, 50V, 100pF 3
C 928, 933 F1G1A104A014 CAPACITOR, 10V, 0.1µF 2
C 940, 941 F1H1A474A028 CAPACITOR, 10V, 0.47µF 2
F 902 S K5H202Z00005 FUSE, 2A, 32V 1
IC 900 C1CB00002449 IC, AUDIO CODEC 1
IC 901 C0CBCBC00130 IC, REGURATOR 1
IC 902 C0JBAE000306 IC, 1
IC 903 C0JBAS000251 IC 1
IC 904 C0ABBA000093 IC, OP AMP 1
IC 905 AN12945A-VB IC, AUDIO AMP 1
KJ 901, 902 K2HC103B0197 JACK 2
KJ 903 K1QZA1AE0001 CONNECTOR 1
L 900, 901, 904, 905, 907 J0JCC0000286 INDUCTOR 5
L 902, 903 J0MAB0000174 INDUCTOR 2
Q 900, 905, 906 B1GBCFNN0042 TRANSISTOR 3
Q 902 XP0421300L TRANSISTOR 1
Q 903, 904 B1CFGD000023 TRANSISTOR 2
Q 907 B1GDCFNN0031 TRANSISTOR 1
920, 921, 929, 931, 936,
942, 943, 948
R 903, 930, 934 ERJ2GEJ222X RESISTOR, 1/16W, 2.2KΩ 3
R 905, 910, 925 ERJ2GEJ472X RESISTOR, 1/16W, 4.7KΩ 3
933, 946
R 923, 927, 935, 937 ERJ2GEJ102X RESISTOR, 1/16W, 1KΩ 4
R 939 ERJ3GEY0R00V RESISTOR, 1/16W, 0Ω 1
R 941 ERJ2RHD203X RESISTOR, 1/16W, 20KΩ 1
IO PCB
C 880 F1H1H104A748 CAPACITOR, 50V, 0.1µF 1
11-13
C 883 F1L1E106A017 CAPACITOR, 25V, 10µF 1
889, 890
C 891 F1G1C104A042 CAPACITOR, 16V, 0.1µF 1
C 892, 893 EZASCE101M CAPACITOR ARRAY 2
CH 883 S DFJS1063ZA I/O DC CABLE 1
CN 881 K1FA209BA004 CONNECTOR 1
CN 882 K1FB115BA014 CONNECTOR 1
D 881 MA2J72900L DIODE 1
D 902 B0JDBE000002 DIODE 1
D 880 B0JCPD000023 DIODE 1
KJ 880 S K2EEYB000001 JACK 1
L 880 J0JKC0000007 INDUCTOR 1
L 881, 882, 883, 884, 885, J0JCC0000186 INDUCTOR 7
886, 887
PA 880 S D4FB1R100009 SWITCH 1
Q 898 B1CHRD000001 TRANSISTOR 1
Q 899 B1DBGD000006 TRANSISTOR 1
R 882, 883, 884 ERJ2RKF75R0X RESISTOR, 1/16W, 75Ω 3
PAD PCB
C 805 F1J0J106A016 CAPACITOR, 6.3V, 10µF 1
CN 802 K1MY40A00001 CONNECTOR 1
CN 803, 805 K1MN08AA0068 CONNECTOR 2
CN 804, 807 K1KA02BA0014 CONNECTOR 2
F 800 S K5H202Z00005 FUSE, 2A, 32V 1
IC 800 C0EBE0000460 IC 1
IC 801 C1DB00001417 IC, FLAT PAD CONTROLLER 1
Q 800, 801 B1GKCFJN0004 TRANSISTOR 2
R 803 ERJ2GEJ105X RESISTOR, 1/16W, 1MΩ 1
RA 800 D1H81034A024 RESISTOR ARRAY 1
SW 800, 801 K0ZZ00000618 SW 2
SW 802, 803 EVQPLDA15 SWITCH 2
X 800 H2D400400012 OSCILLATOR, 4MHz 1
SW PCB
LD 951 B3ABB0000210 DIODE 1
SW 950, 951, 952, 953, 954, EVQPLDA15 SWITCH 6
9
LED-LEFT PCB
LD 841, 842, 843, 844, 845, B3ABB0000210 DIODE 6
8 6
PR PCB
C 851, 852, 854 F1J1A1050021 CAPACITOR, 10V, 1µF 3
C 855, 856, 857 J0MAB0000146 INDUCTOR 3
CA 851, 852, 854, 857, 858, J0HABC000004 CAPACITOR ARRAY 6
8 9
CN 850 K1KYA0A00018 CONNECTOR 1
11-14
CN 851 K1KAA0AA0244 CONNECTOR 1
L 852, 853 J0JJC0000015 INDUCTOR 2
L 850 J0MAB0000200 INDUCTOR 1
LED-RIGHT PCB
LD 781 B3AGB0000040 DIODE 1
LD 782 B3ADB0000065 DIODE 1
LD 783 B3ABB0000210 DIODE 1
SD PCB
C 890 F1G1C104A042 CAPACITOR, 16V, 0.1µF 1
CN 890 K1NA09E00076 CONNECTOR 1
LD 890 B3ACB0000020 DIODE 1
R 891 ERJ2GE0R00X RESISTOR, 1/16W, 0Ω 1
HSDPA PCB
C 600, 603 F1G1H1010005 CAPACITOR, 50V, 100pF 2
C 601, 602, 604, 608 F1J0J106A016 CAPACITOR, 6.3V, 10µF 4
C 609, 610, 619 EEFUD0J151ER CAPACITOR, 6.3V, 150µF 3
C 611, 612, 613, 614, 615, F1G1C104A042 CAPACITOR, 16V, 0.1µF 8
616, 617, 620
CN 602 K1NA08E00006 CONNECTOR 1
CN 603 K1FY104BA024 CONNECTOR, USB 1
D 600 B0KB00000044 DIODE 1
D 603 DEDRB081L20 DIODE 1
IC 600 C0JBAZ002422 IC, FET SWITCH 1
IC 601 C0JBAC000382 IC, LOGIC 1
IC 602 C0DBAYY00204 IC, DC/DC CONVERTER 1
IC 603 C0DBZGD00016 IC 1
IC 604 C0DBZYY00026 IC, USB POWER SW 1
IC 605 C0EBE0000460 IC 1
KJ 600, 601 K1QZA1AE0001 CONNECTOR 2
L 600, 601 J0JJC0000015 INDUCTOR 2
L 602 J0MAB0000200 INDUCTOR 1
L 603 G1C2R7MA0273 INDUCTOR, COIL 1
Q 600 B1DHFD000015 TRANSISTOR 1
Q 602, 604 B1GBCFNN0042 TRANSISTOR 2
Q 603 B1CFGD000023 TRANSISTOR 1
R 602, 606, 609, 615, 616 ERJ2GEJ103X RESISTOR, 1/16W, 10KΩ 5
R 603, 613 ERJ2GE0R00X RESISTOR, 1/16W, 0Ω 2
R 604, 611, 612, 619 ERJ2GEJ101X RESISTOR, 1/16W, 100Ω 4
R 610 ERJ6GEY0R00V RESISTOR, 1/10W, 0Ω 1
SW 600 K0D444A00041 SWTICH 1
ZA 600, 601 K1YGZZ000060 SPACER 2
POWER SW PCB
11-15
SW 980 K0D112A00096 SW 1
TS PCB
C 900, 901, 902, 903 F1G1E472A062 CAPACITOR, 25V, 4700pF 4
C 904, 905, 906, 907 F1G1H681A496 CAPACITOR, 50V, 680pF 4
C 913, 916 F1J0J106A016 CAPACITOR, 6.3V, 10µF 2
C 914 F1G0J224A001 CAPACITOR, 6.3V, 0.22µF 1
CN 901 K1KA06BA0014 CONNECTOR 1
IC 900 C0EBE0000460 IC 1
IC 902 C1CB00002515 IC, TOUCHPANEL CONTROLLER 1
Q 900, 901 XP0431400L TRANSISTOR 2
Q 902 B1GDCFNN0031 TRANSISTOR 1
912, 917, 918, 922, 923
R 913, 914, 915, 916 ERJ2GEJ822X RESISTOR, 1/16W, 8.2KΩ 4
R 919, 925 ERJ2GE0R00X RESISTOR, 1/16W, 0Ω 2
R 926 DEARA8AJ473M RESISTOR ARRAY 1
R 929 ERJ2GEJ152X RESISTOR, 1/16W, 1.5KΩ 1
X 900 H2D600400005 OSCILLATOR, 6MHz 1
EXTENAL ANTENNA PCB

CN 1 K1QZB2AA0002 COAXIAL CONNECTOR 1
CN 2, 3, 4, 5 K1QZA1AE0001 CONNECTOR 4
BLUETOOTH PCB
C1 F1J0J106A016 CAPACITOR, 6.3V, 10µF 1
C 2, 4, 7, 11 F1G1C104A042 CAPACITOR, 16V, 0.1µF 4
C 6, 9 F1G1E103A062 CAPACITOR, 25V, 0.01µF 2
C8 F1G1H270A542 CAPACITOR, 50V, 27pF 1
IC 1 C0JBAZ002422 IC, FET SWITCH 1
IC 2 0 N5HZZ0000040 BLUETOOTH MODULE 1
IC 3 C0EBE0000460 IC 1
KJ 1 K1QZA1AE0001 CONNECTOR 1
L 1, 2 J0JJC0000015 INDUCTOR 2
L4 G1C5N6ZA0029 INCUCTOR 1
L5 J0MAB0000200 INDUCTOR 1
Q1 B1GBCFJN0037 TRANSISTOR 1
Q2 B1DHDC000028 TRANSISTOR 1
HDD FPC
CF 1 D4CC1103A038 THERMISTOR 1
CN 3 K1KA04BA0014 CONNECTOR 1
BATTERY FPC
CN 1 K1KY10B00010 CONNECTOR 1
11-16

CF 19 Chbaxbm

Uploaded by

Document Informationclick to expand document information2

Document Informationclick to expand document information

Copyright:

Available Formats

CF 19 Chbaxbm

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

CF 19 Chbaxbm

Uploaded by

Copyright:

Available Formats

ORDER NO.

Model No. CF-19CHBAXBM

This is the Service Manual for

Model No. CF-19CHBAX 1 2

© 2006 Matsushita Electric Industrial Co., Ltd. All rights reserved.

Downloaded from www.Manualslib.com manuals search engine

Downloaded from www.Manualslib.com manuals search engine

Chipset Intel® 945GM

Downloaded from www.Manualslib.com manuals search engine 1-1

Wireless LAN <Only for model with wireless LAN>

BluetoothTM <Only for model with Bluetooth>

Downloaded from www.Manualslib.com manuals search engine 1-2

A: Wireless LAN Antenna G: LCD

Downloaded from www.Manualslib.com manuals search engine 2-1

Rear side Bottom

A: DC-IN Jack L: Microphone Jack

Downloaded from www.Manualslib.com manuals search engine 2-2

Downloaded from www.Manualslib.com manuals search engine 4-1

Set cannot be supplied with current. AC NG

Dark display on screen. NG Replace inverter board.

LCD back NO Replace LCD back light.

BIOS operation NO Replace main board (Check fuse at power source).

Result of NG Refer to POST Replace main board.

Set-up utility NG Replace main board. Heavy trouble e.g.,

Check HDD cable connection and continuity.

Starts but operates unstably. Reinstall HDD.

Downloaded from www.Manualslib.com manuals search engine 4-2

Error Diagnosis by Checking Beep Signal Sound

(1 (long sound) -2-3-4)

Table of errors classified by beep sounds

Diagnosis Beep signal sound Error message

Downloaded from www.Manualslib.com manuals search engine 5-1

0200 Failure Fixed Disk

Downloaded from www.Manualslib.com manuals search engine 6-1

Downloaded from www.Manualslib.com manuals search engine 6-2

Downloaded from www.Manualslib.com manuals search engine 7-1

Downloaded from www.Manualslib.com manuals search engine 7-2

Start the standard test Do not test

2-2. "PC-Diagnostic utility" End method

Standard at test time

Downloaded from www.Manualslib.com manuals search engine 7-3

Place with possibili-

CPU / CPU is shifted to protected mode, and CPU /

RAM All memory space is tested in a spe- Memory / Main-

MODEM It is confirmed not to find abnormality MODEM/ Main-

Wireless It is confirmed not to find abnormality Wireless LAN

PC Card It is confirmed not to find abnormality Mainboard

SD It is confirmed not to find abnormality Mainboard

DVD-ROM *6 The drive is normally reset, and it is It is confirmed to be able to Mainboard /

Downloaded from www.Manualslib.com manuals search engine 7-4

Downloaded from www.Manualslib.com manuals search engine 7-5

TS PS2 PCB LCD

AUDIO PCB MODEM

TOUCH PAD HDD

Downloaded from www.Manualslib.com manuals search engine 8-1

9.1. Disassembly Instructions HDD Case B

9.1.2. Removing the Battery Pack and