Introduction to Process

Control
Chapter 1

a) prototype system-blending tank

b) feedback control
c) implementation of control
d) justification of control

1
Chapter 1

Process
- The conversion of feed materials
to products using chemical and
physical operations.

2
 Chapter 1

3
 Chapter 1

4
 Chapter
Chapter11

5
 Control Terminology
controlled variables - these are the variables which
quantify the performance or quality of the final
product, which are also called output variables.
Chapter 1

manipulated variables - these input variables are

adjusted dynamically to keep the controlled variables
at their set-points.
disturbance variables - these are also called "load"
variables and represent input variables that can
cause the controlled variables to deviate from their
respective set points.

6
 Control Terminology(2)

set-point change - implementing a change in the

operating conditions. The set-point signal is
Chapter 1

changed and the manipulated variable is adjusted

appropriately to achieve the new operating
conditions. Also called servomechanism (or "servo")
control.
disturbance change - the process transient
behavior when a disturbance enters, also called
regulatory control or load change. A control system
should be able to return each controlled variable
back to its set-point.

7
Chapter 1 Illustrative Example: Blending system

Notation:
• w1, w2 and w are mass flow rates
• x1, x2 and x are mass fractions of component A
8
 Assumptions:
1. w1 is constant
2. x2 = constant = 1 (stream 2 is pure A)
3. Perfect mixing in the tank
Chapter 1

Control Objective:
Keep x at a desired value (or “set point”) xsp, despite variations in
x1(t). Flow rate w2 can be adjusted for this purpose.

Terminology:
• Controlled variable (or “output variable”): x
• Manipulated variable (or “input variable”): w2
• Disturbance variable (or “load variable”): x1 9
 Design Question. What value of w2 is required to have
x = xSP ?

Overall balance:
0 = w1 + w2 − w (1-1)
Chapter 1

Component A balance:
x =x xSP
w1x1 + w2 2 − wx = 0 (1-2)

(The overbars denote nominal steady-state design values.)

• At the design conditions, x = xSP. Substitute Eq. 1-2, and

x2 = 1 , then solve Eq. 1-2 for w2 :
xSP − x1
w2 = w1 (1-3)
1 − xSP
10
 • Equation 1-3 is the design equation for the blending
system.
• If our assumptions are correct, then this value of w2 will keep x
at xSP . But what if conditions change?
Chapter 1

Control Question. Suppose that the inlet concentration x1

changes with time. How can we ensure that x remains at or near
the set point xSP ?
As a specific example, if x1  x1 and w2 = w2, then x > xSP.

Some Possible Control Strategies:

Method 1. Measure x and adjust w2.
• Intuitively, if x is too high, we should reduce w2;
11
 • Manual control vs. automatic control
• Proportional feedback control law,
w2 ( t ) = w2 + Kc  xSP − x ( t ) (1-4)

1. where Kc is called the controller gain.

Chapter 1

2. w2(t) and x(t) denote variables that change with time t.

3. The change in the flow rate, w2 ( t ) − w2 , is proportional to
the deviation from the set point, xSP – x(t).

12
 Chapter 1

13
 Method 2. Measure x1 and adjust w2.
• Thus, if x1 is greater than x1, we would decrease w2 so that
w2  w2 ;

• One approach: Consider Eq. (1-3) and replace x1 and w2 with

x1(t) and w2(t) to get a control law:
Chapter 1

xSP − x1 ( t )
w2 ( t ) = w1 (1-5)
1 − xSP

14
 Chapter 1

15
 • Because Eq. (1-3) applies only at steady state, it is not clear
how effective the control law in (1-5) will be for transient
conditions.

Method 3. Measure x1 and x, adjust w2.

• This approach is a combination of Methods 1 and 2.
Chapter 1

Method 4. Use a larger tank.

• If a larger tank is used, fluctuations in x1 will tend to be damped
out due to the larger capacitance of the tank contents.
• However, a larger tank means an increased capital cost.

16
 Classification of Control Strategies

Table. 1.1 Control Strategies for the Blending System

Method Measured Manipulated Category
Variable Variable
Chapter 1

1 x w2 FB
2 x1 w2 FF
3 x1 and x w2 FF/FB
4 - - Design change

Feedback Control:
• Distinguishing feature: measure the controlled variable
17
 • It is important to make a distinction between negative feedback
and positive feedback.
➢ Engineering Usage vs. Social Sciences
• Advantages:
➢ Corrective action is taken regardless of the source of
Chapter 1

the disturbance.
➢ Reduces sensitivity of the controlled variable to
disturbances and changes in the process (shown later).
• Disadvantages:
➢ No corrective action occurs until after the disturbance
has upset the process, that is, until after x differs from
xsp.
➢ Very oscillatory responses, or even instability…
18
 Feedforward Control:
➢ Distinguishing feature: measure a disturbance
variable
• Advantage:
➢ Correct for disturbance before it upsets the process.
Chapter 1

• Disadvantage:
➢ Must be able to measure the disturbance.
➢ No corrective action for unmeasured disturbances.

19
 Closed-loop Artificial Pancreas
glucose u
setpoint
y
r

controller pump patient sensor

measured glucose

20
 Chapter 1

21
Chapter 1

Block diagram for temperature feedback control system

22
Chapter 1

Figure 1.6 Block diagram for composition feedback control system

on Fig. 1.4.

23
 or
pneumatic
controller
Chapter 1

24
 Justification of Process Control

Specific Objectives of Control

• Increased product throughput
Chapter 1

• Increased yield of higher valued products

• Decreased energy consumption
• Decreased pollution
• Decreased off-spec product
• Increased Safety
• Extended life of equipment
• Improved Operability
• Decreased production labor

25
 3.2 Economic Incentives - Advanced
Control
Chapter 1

26
 Chapter 1

27
 (days- months) 5. Planning and
Scheduling

(hours-days) 4. Real-Time
Optimization

3b. Multivariable
Chapter 1

(minutes-hours) and Constraint

Control
Figure 1.8 Hierarchy of
process control activities.

(seconds-minutes) 3a. Regulatory

Control

2. Safety, Environment
(< 1 second) and Equipment
Protection

(< 1 second) 1. Measurement

and Actuation

Process

28
Chapter 1

Figure 1.10 Major

steps in control
system development

29
Chapter 1

Next
3 chapter
0