Revised on : 11. December.

2013

Cal. NH35A

ψψ 27. 40
(
mm
29. 36 mm with Dial Holding Spacer)

H 5. 32 mm

Item Version No.

Specification Version 2
Appearance - 1 Version 1
Appearance - 2 Version 1
Casing Version 1
Hand Fitting Version 1
Hand Setting Stem Version 1
Dial Version 1
Assembly Plan Version 1
Hands Version 1

SII Products
 MOVEMENT SPECIFICATION

CAL.NH35A 12 Ligne Mechanical Movement

Three Hands with Date

1. MOVEMENT DIMENSIONS
· Outside diameter ψ27.40 mm
· Casing diameter ψ29.36 mm (with dial holding spacer)
· Total height 5.32 mm

2. FUNCTIONS
· Winding mechanism Manual winding
Automatic winding with ball bearing
Both winding with one way clutch
· Additional function Date display with quick date correction, second hand reset
· Jewels 24 jewels
· Accuracy -20 ~ +40 seconds per day (23º± 2ºC)
· Shock resistance Shock-absorber device for balance staff
· Vibration frequency 6 vibrations per second (21,600 vibrations per hour)
· Duration time More than 41 hours
· Regulation hands unbalance Hour : Less than 1.50 µN·m ( 150 mg·mm )
Minute : Less than 1.25 µN·m ( 125 mg·mm )
Second : Less than 0.20 µN·m ( 20 mg·mm )
· Antimagnetic DC : ≧ 4800 A / m

3. HANDLING AND CORRECTIONS

1) Crown at normal position Clockwise : Manual winding
Counterclockwise : Free
2) Crown pulled out to 1st click Clockwise : Free
Counterclockwise : Quick date correction
3) Crown pulled out to 2nd click Time setting, second hand reset

4. DIAL FIXED METHOD The dial is fixed by two dial leg holes of dial holding spacer

5. TEST OF ACCURACY
· Equipment to be used Witschi WATCH EXPERT
· Duration of measurement 20 seconds

6. FITTING FORCE FOR HANDS

Hour hand : Less than 50 N
Minute hand : Less than 50 N
Second hand : Less than 30 N

7. CASING The movement is fixed by dial holding spacer

*1. Screw type case back is required
*2. Non-corresponding with Diver's watch

* All specifications are subject to change without notice.

SII Products Version: 2

 Revised
Revised on : 13.on: 24. Aug. 2012
December. 2013

TECHNICAL GUIDE
&
PARTS CATALOGUE

Cal.NH3 Series

AUTOMATIC MECHANICAL

SII Products
 PARTS CATALOGUE / TECHNICAL GUIDE
Cal.NH3 Series
[SPECIFICATION] Version-02

Movement

Outside diameter Ф 27.40mm

Movement
Casing diameter Ф 29.36mm (with dial holding spacer)
size
Total height 5.32mm
Cal. No. NH35 NH36 NH37 NH38 NH39
3Hands
O O O O O
(hour, minute, second)
Time
Date calendar O O O - -
indication
Day calendar - O - - -
24hour indicator - - O - O
Manual winding O O O O O
Automatic winding
O O O O O
with ball bearing
Basic Time setting with
O O O O O
function stop-second device
Date display with
O O O - -
quick change
Day display with
- O - - -
quick change
Frequency 21,600 vibrations per hour
-20~+40 seconds per day
Static accuracy * Measurement should be done within 10~60 minutes after fully wound up.
* All measurements are made without the calendar in function.
Measurement
Direction of 3 positions. (1) Dial up (2) 9 o'clock up (3) 6 o'clock up
position
Lift angle 53 deg.
Measurement 20 seconds
Accuracy time * Equipment to be used : Witschi WATCH EXPERT
Difference is under 60 seconds within max value and minimum value.
Posture * Measurement should be done within 10~60 minutes after fully wound up.
difference * Direction of 4 positions.
(1) 12 o'clock up (2) 9 o'clock up (3) 6 o'clock up (4) 3 o'clock up
-20~+40 seconds per day.
Isochronisms
* Measurement position : Dial up
(24h-0h)
* Difference of static accuracy of 24h and 0h
More than 41 hours … Mainspring after fully wound up.
Duration time
* Posture to confirmation : Dial up
<< Movement >>
・Fully wound up by turning the crown minimum 55 times.
・Fully wound up by turning the ratchet wheel screw 8 times.
<< Complete Watch >>
Winding the mainspring
A winding machine is needed to wind up the mainspring.
Full wind up conditions
・Rotary speed : 30 rpm
・Operating time: 60 minutes
Jewels 24 jewels
Normal Left rotation Free
position Right rotation Manual winding
Crown
First Left rotation Date setting Date setting Date setting
position Time setting with stop-second device
click Right rotation Free Day setting Free
Second click Time setting with stop-second device -
SII Products 1
 Version-01
PARTS CATALOGUE Cal.NH3 series
Disassembling procedures Figs. Type of oil Oil quantity mark
NH35/37 4 → 19 NH36 1 → 19 Moebius 9010 NORMAL QUANTITY
Reassembling procedures Figs. MO-4 SUFFICIENT QUANTITY
NH35/37 19 → 4 NH36 19 → 1 MO-3

1 0963 300 (Cal.NH36 only

<<NH35/36/37>>
Snap for day star with dial disk

2 Day star with dial disk (Cal.NH36 only

Refer to page 8 for each parts code

3 0989 070 (Cal.NH36 only

4 0012 354 Intermediate wheel for day corrector
Date indicator maintaining plate screw
4 0012 354
Date indicator maintaining plate screw

5 0808 183
Date indicator maintaining plate

6 Date dial
Refer to page 8 for each parts code

7 0810 183
Date jumper

SII Products 2
 Version-03
PARTS CATALOGUE Cal.NH3 series
Type of oil Oil quantity mark
Moebius 9010 MO-4 NORMAL QUANTITY
MO-3 SUFFICIENT QUANTITY

<<NH35/36/37>> 14 Hour wheel 8 0962 025

Refer to page 9 for each parts code Day-date corrector setting
transmission wheel E

9 0012 485
15 0261 183 Guard for day-date corrector
Minute wheel and pinion setting transmission wheel
screw

16 Refer to page 9 for

each parts code 10 0836 183
Guard for day-date corrector
17 Refer to page 9 for setting transmission wheel
each parts code
11 0962 185
Day-date corrector
setting transmission
18 Cannon pinion wheel C
Refer to page 8 for 12 0962 023
each parts code *3 Day-date corrector
setting transmission
wheel B

13 0737 183
*3 Day-date corrector wheel

19 4408 172
Dial holding spacer
*1

*2
*1
37-1
*2
Lower shock
absorbing spring
37-2
Lower shock
absorbing cap jewel
37-3
Lower hole jewel frame
for shock-absorber

SII Products 3
 Version-02
PARTS CATALOGUE Cal.NH3 series
Disassembling procedures Figs. Type of oil Oil quantity mark
NH38/39 1 → 8 Moebius 9010 NORMAL QUANTITY
Reassembling procedures Figs. MO-4 SUFFICIENT QUANTITY
NH38/39 8 → 1 MO-3

<<NH38/39>> 1 0012 354

Hour wheel guard screw

2 0376 184
Hour wheel guard

3 Hour wheel
Refer to page 9 for each parts code

4 0261 183
Minute wheel and pinion

6 0157 184 (Cal.NH39 only 5 0817 300 (Cal.NH39 only

24hour wheel Intermediate 24hour wheel and pinion

7 Cannon pinion
Refer to page 8 for each parts code
*2
*2
8 4408 172
Dail holding spacer

*1

*1 37-1
Lower shock
absorbing spring

37-2
Lower shock absorbing
cap jewel
37-3
Lower hole jewel frame
for shock-absorber

SII Products 4
 Version-02
PARTS CATALOGUE Cal.NH3 series
Disassembling procedures Figs. Type of oil Oil quantity mark
1 → 37 Moebius 9010 NORMAL QUANTITY
Reassembling procedures Figs. MO-4 SUFFICIENT QUANTITY
37 → 1 MO-3

1 Oscillating weight with ball bearing

*2
Refer to page 8 for each parts code

*2
2 0012 354
Automatic train bridge screw
7 0012 420
Balance bridge screw 3 0191 183
Automatic train bridge

*1

whole tooth 4 0514 183

Second reduction wheel and pinion

8 0171 353
Balance cock
5 0012 919
Ratchet wheel screw

6 0285 051
Ratchet wheel

9 0012 354
Pallet bridge screw

10 0161 300
Pallet bridge
8-1
Balance
complete 11 0301 009
*3
Refer to page 8 for Pallet fork
each parts code

*3

*1
8-2
Upper shock absorbing spring

8-3
Upper shock absorbing
cap jewel

8-4
Upper hole jewel frame for
shock-absorber

SII Products 5
 Version-04
PARTS CATALOGUE Cal.NH3 series
Type of oil Oil quantity mark
Moebius 9010 MO-4 NORMAL QUANTITY
MO-3 SUFFICIENT QUANTITY
17 0511 010 12 0012 420
First reduction wheel Barrel and train wheel bridge screw
Refer to page 10 for oiling spot
13-1 Cap jewelled spring

13-2 Cap jewel

16 0831 183
Pawl lever 14 0363 184
Ratchet sliding wheel spring

13 0114 183
Barrel and train wheel bridge
with hole jewel frame
Refer to page 10 for oiling spot

15 0836 002
Reduction wheel holder 18 0436 166
Lower plate for barrel and train
*1 wheel bridge

20 Fourth wheel and pinion 19 0012 354

Refer to page 8 for Lower plate for barrel and train
each parts code wheel bridge screw

21 0231 070
Third wheel and pinion

*1 22 0381 004
Click

23 0201 083
Barrel complete with mainspring

SII Products 6
 Version-02
PARTS CATALOGUE Cal.NH3 series
Type of oil Oil quantity mark
Moebius 9010 MO-4 NORMAL QUANTITY
MO-3 SUFFICIENT QUANTITY

24 0012 354
Center wheel bridge screw

25 0122 302
Center wheel bridge

26 0251 300
Escape wheel and pinion
*1
*1 27 Center wheel and pinion
Refer to page 8 for each parts code

28 0012 168
Yoke spring screw

29 0388 177
Yoke spring

30 Yoke
Refer to page 8 for each parts code

31 Setting lever
Refer to page 8 for each parts code

32 0601 183
Balance stop lever *2 *3

*4
Refer to page 11 for oiling spot
34 0282 183
Clutch wheel
*2
*4 35 0283 020
Winding pinion
*3
*5 36 0962 183 (Cal.NH35/36/37
Day-Date corrector setting
transmission wheel A

33 0351 200
Winding stem
*5
37 Main plate

SII Products 7
 Version-04
PARTS CATALOGUE Cal.NH3 series

2 Day star with dial disk …Cal.NH36 only (P-2)

Position Position of Color of
Parts code Color of letters Language
of crown day frame background
MON FRI～ : Black
0160 242 3H 3H SAT : Blue White English & Spanish
SUN : Red

6 Date dial … Cal.NH35 / NH36 / NH37 (P-2)

Position Position of Color of Color of
Cal. Parts code
of crown day frame letters background
NH35
0878 208 3H 3H Black White
NH37
NH36 0878 206 3H 3H Black White

18 Cannon pinion …NH35/36/37 (P-3) 7 Cannon pinion …NH38/39 (P-4)

Cal. Parts code Cal. Parts code Cal. Parts code Cal. Parts code
NH35
0225 416 NH37 0225 417 NH38 0225 416 NH39 0225 417
NH36

1 Oscillating weight with ball bearing (P-5)

Cal. Parts code Marking Cal. Parts code Marking Cal. Parts code Marking
0509 467 Japan mark 0509 463 Japan mark 0509 470 Japan mark
NH35 NH36 NH37
0509 468 Malaysia mark 0509 464 Malaysia mark 0509 471 Malaysia mark

Cal. Parts code Marking Cal. Parts code Marking

0509 476 Japan mark 0509 473 Japan mark
NH38 NH39
0509 477 Malaysia mark 0509 474 Malaysia mark

8-1 Balance complete with stud (P-5) 20 Fourth wheel and pinion (P-6)
Cal. Parts code Cal. Parts code Cal. Parts code Cal. Parts code
NH35 NH35
NH38 NH37
NH36 0310 197 0310 198 NH36 0144 184 0144 185
NH39 NH39
NH37 NH38

27 Center wheel and pinion 30 Yoke (P-7)

with cannon pinion (P-7) Cal. Parts code Cal. Parts code
Cal. Parts code Cal. Parts code NH35
NH38
NH35 NH36 0384 183 0384 184
NH37 NH39
NH36 0224 184 0224 185 NH37
NH39
NH38

31 Setting lever (P-7)

Cal. Parts code Cal. Parts code
NH35
NH38
NH36 0383 185 0383 186
NH39
NH37

SII Products 8
 Version-02
PARTS CATALOGUE Cal.NH3 series
Remarks: Different parts for each CAL.
Cal.
Page No Parts code Parts name Parts form
NH35 NH36 NH37 NH38 NH39
0273 182 &184
O - - - - 0273 182 Hour wheel
0273 182 ⇒ 0273 184
P-3 14 - O - - - 0273 183 (Height difference)

- - O - - 0273 184
0273 183 & 185
- - - O - 0273 183 0273 183 ⇒ 0273 185
P-4 3 (Height difference)
- - - - O 0273 185
Intermediate date driving wheel
O O - - -
and pinion
P-3 16 0817 300
Intermediate 24hour wheel
- - O - O
and pinion

O O - - - 0802 183 Date indicator driving wheel

P-3 17

- - O - - 0157 182 24hour wheel

■ List of screw
Page No Parts code Parts name Parts form Page No Parts code Parts name Parts form
Date indicator maintaining Guard for day-date
P-2 4 plate screw (x4) corrector setting
P-3 9 0012 485
Hour wheel guard screw transmission wheel
P-4 1 screw (x2)
(x4)
Automatic train bridge
2
screw (x2) P-5 5 0012 919 Ratchet wheel screw
P-5 0012 354
9 Pallet bridge screw (x2)

Lower plate for barrel and P-5 7 Balance bridge screw

P-6 19 train wheel bridge screw
0012 420
Center wheel bridge
P-7 24 Barrel and train wheel
screw P-6 12
bridge screw (x3)

P-7 28 0012 168 Yoke spring screw (x2)

SII Products 9
 Version-01
TECHNICAL GUIDE Cal.NH3 series
Type of oil Oil quantity mark
Moebius 9010 NORMAL QUANTITY
MO-4 SUFFICIENT QUANTITY
MO-3

1.Oiling spot
13 Barrel and train wheel bridge with hole jewel frame

*1
*1

Barrel and train wheel bridge with hole jewel frame (back side)

*3
*2 *4 *3

*2

Note
*2 After oiling, set lower plate for barrel and train wheel bridge & screw.

18 Lower plate for barrel and train wheel bridge

19 Lower plate for barrel and train wheel bridge screw

*4 After oiling, set first reduction wheel & pawl lever & reduction wheel holder.
17 First reduction wheel
17 First reduction wheel

16 Pawl lever

15 Reduction wheel holder

SII Products 10
 Version-01
TECHNICAL GUIDE Cal.NH3 series

32 Balance stop lever

Balance stop lever

Main plate

Contact part of main plate and balance stop lever

2.Setting position of oscillating weight

・Before assembling oscillating weight.
Match the center of the oscillating weight and winding stem. Set the hole of first reduction wheel gear on the
imaginary line toward the balance bridge guide pin.

Enlarged
view

Balance bridge guide pin First reduction wheel gear

3.To remove the winding stem

1) Set the winding stem to normal position.
2) Pull out the winding stem, while pushing "A" A

31 Setting lever

33 Winding stem

SII Products 11
 Version-01
TECHNICAL GUIDE Cal.NH3 series
4.Disassembling / assembling of the First reduction wheel
<< Disassembling >> << Assembling >>

17 First reduction wheel

15 Reduction wheel holder

13 Barrel and train wheel bridge (back side)

5.Disassembling / assembling of the Ratchet sliding wheel spring.

<< Disassembling >> << Assembling >>
14 Ratchet sliding wheel spring

13 Barrel and train wheel bridge with hole jewel frame

PUSH

Remove the hook of the ratchet sliding wheel spring

The hooks of ratchet sliding wheel spring are hung up
from barrel and train wheel bridge with hole jewel
on barrel and train wheel bridge with hole jewel frame.
frame.

SII Products 12
 Version-01
TECHNICAL GUIDE Cal.NH3 series
6.Accuracy adjustment

Regulator

Regulator pin
Stud support

Note:
・Regulator ( Time adjustment ・Stud support ( Beat error adjustment

(+) side

(-) side
・Regulator pin ( Gap adjustment of balance spring and regulator pin
Anticlockwise rotation No clockwise rotation

SII Products 13
 Version-02
TECHNICAL GUIDE Cal.NH3 series
7.To wind up the mainspring
<<Movement>>
The mainspring would be fully wound up by turning the ratchet wheel screw 8 times clockwise. (Manual winding or Screwdriver)
Manual winding … Rotate crown clockwise at normal position by min 55 times. (Equal to ratchet wheel screw 8 times )
Screwdriver winding … Turn the ratchet wheel screw 8 times clockwise.
[ Manual winding ] [ Screwdriver winding ]

Screwdriver

Ratchet wheel screw

Ratchet wheel

8.How to attach hands

Place the movement directly on a flat metal plate or something similar to attach the hands.
We recommend the use of movement holder to attach hands. Static weighting
For hands attachment, please use a special equipment.
When the movement receives a strong shock, it may be damaged.
*Install the 24hour hand. …Cal.NH37 & NH39
Pull out the crown to the second click position and rotation it clockwise
to install 24hour hand.

Metal plate

9.Accuracy measurement condition

Static Accuracy : -20~+40 seconds per day
Measurement Conditions
1) Measurement should be done within 10~60 minutes after fully wound up.
2) Lift angle : 53 deg
3) Measurement position : (1) Dial up (2) 9 o'clock up (3) 6 o'clock up
4) Minimum measurement Time : 20 seconds
5) Stabilizing Time :
Leave the watch for at least 20 seconds to stabilize after you change its measurement position.

10.About the handling ...Cal.NH38 & 39

○ Part is processed as a mirror surface. It is damaged when touching with tweezers.
Please be careful about the handling.

SII Products 14
 Version-02
OPERATION Cal.NH3 series

NH35 / NH36 / NH37 NH38 / NH39

Hour hand 24hour hand
Hour hand Minute hand
Minute hand
Crown at normal position
Crown at second position Crown at first position

Crown at first position Crown at normal position

Second hand
Date Second hand

Day

Time indication NH35 NH36 NH37 NH38 NH39

3Hands
O O O O O
(hour, minute, second)

Date calendar O O O - -

Day calendar - O - - -

24hour indicator - - O - O

1.How to set the time

1) Pull out the crown to the second click position. >Cal.NH35 & NH36 & NH37
Pull out the crown to the first click position. >Cal.NH38 & NH39
2) Turn the crown to set hour and minute hands.
(Check that AM / PM is set correctly.)
3)Push the crown back into the normal position.

2.How to set the Date (Cal.NH35 & NH36 & NH37

1) Pull out the crown to the first click position.
2) Turn the crown to left for date setting.
3) Turn the crown to right for day setting. >Cal.NH36 only
*Do not set the date between 9:00 P.M. and 4:00 A.M. as this will cause a malfunction.
3)Push the crown back into the normal position.

3.To wind up the mainspring

a) Manual winding > Rotate the crown clockwise at normal position.
Wind turning the ratchet wheel screw 8 times. It will start to move naturally after shaking slightly.
b) To wind up with winding machine.
Full wind up conditions
・Rotary speed : 30 rpm
・Operating time : 60 rpm

SII Products 15
NH Basic Mechanical Series (3 Hands/Date) - Window Variation List Date : 20.10.2016

Reference NH15A11WMN NH35A31J NH35A31J05 NH35A31M

Product Line NH Basic Mechanical Series NH Basic Mechanical Series NH Basic Mechanical Series NH Basic Mechanical Series

Function 3 Hands/Date 3 Hands/Date 3 Hands/Date 3 Hands/Date

Appearance

Size 10 1/2''' 12''' 12''' 12'''

*Category B B B B
Spec Sheet Dial Drawing No. NH15 Dial - 1 NH35 Dial - 1 NH35 Dial - 1 NH35 Dial - 1
Postion Stem 3H 3H 3H 3H
Date 3H 3H 3H 3H
Date Disc Color White base Black letter White base Black letter White base Black letter White base Black letter
Hands Fitting Type Hands : TYPE M Hands : TYPE M Hands : TYPE M Hands : TYPE M
Stem Type Standard Standard Standard Standard
C/O Marking on Rotor JAPAN JAPAN MALAYSIA
Remarks CDG on rotor
*Category A : Ordinary Production (Stock Item) ; Category B : Order Based Production
NH Basic Mechanical Series (3 Hands/Date) - Window Variation List Date : 20.10.2016

Reference NH35A31MN NH35A31MN07 NH35A41J NH35A41MN

Product Line NH Basic Mechanical Series NH Basic Mechanical Series NH Basic Mechanical Series NH Basic Mechanical Series

Function 3 Hands/Date 3 Hands/Date 3 Hands/Date 3 Hands/Date

Appearance

Size 12''' 12''' 12''' 12'''

*Category B B B B
Spec Sheet Dial Drawing No. NH35 Dial - 1 NH35 Dial - 1 NH35 Dial - 1 NH35 Dial - 1
Postion Stem 3H 3H 3H 3H
Date 3H 3H 3H 3H
Date Disc Color White base Black letter White base Black letter White base Black letter White base Black letter
Hands Fitting Type Hands : TYPE M Hands : TYPE M Hands : TYPE L Hands : TYPE L
Stem Type Standard Standard Standard Standard
C/O Marking on Rotor JAPAN
Remarks CDG on rotor
*Category A : Ordinary Production (Stock Item) ; Category B : Order Based Production
NH Basic Mechanical Series (3 Hands/Date) - Window Variation List Date : 20.10.2016

Reference NH35A41MN07 NH15A11JB NH35A31JB NH35A31JB05

Product Line NH Basic Mechanical Series NH Basic Mechanical Series NH Basic Mechanical Series NH Basic Mechanical Series

Function 3 Hands/Date 3 Hands/Date 3 Hands/Date 3 Hands/Date

Appearance

Size 12''' 10 1/2''' 12''' 12'''

*Category B B B B
Spec Sheet Dial Drawing No. NH35 Dial - 1 NH15 Dial - 1 NH35 Dial - 1 NH35 Dial - 1
Postion Stem 3H 3H 3H 3H
Date 3H 3H 3H 3H
Date Disc Color White base Black letter Black base White letter Black base White letter Black base White letter
Hands Fitting Type Hands : TYPE L Hands : TYPE M Hands : TYPE M Hands : TYPE M
Stem Type Standard Standard Standard Standard
C/O Marking on Rotor JAPAN JAPAN JAPAN
Remarks CDG on rotor CDG on rotor
*Category A : Ordinary Production (Stock Item) ; Category B : Order Based Production
NH Basic Mechanical Series (3 Hands/Date) - Window Variation List Date : 20.10.2016

Reference NH35A31MB NH35A31MNB NH35A31MNB07 NH35A41JB

Product Line NH Basic Mechanical Series NH Basic Mechanical Series NH Basic Mechanical Series NH Basic Mechanical Series

Function 3 Hands/Date 3 Hands/Date 3 Hands/Date 3 Hands/Date

Appearance

Size 12''' 12''' 12''' 12'''

*Category B B B B
Spec Sheet Dial Drawing No. NH35 Dial - 1 NH35 Dial - 1 NH35 Dial - 1 NH35 Dial - 1
Postion Stem 3H 3H 3H 3H
Date 3H 3H 3H 3H
Date Disc Color Black base White letter Black base White letter Black base White letter Black base White letter
Hands Fitting Type Hands : TYPE M Hands : TYPE M Hands : TYPE M Hands : TYPE L
Stem Type Standard Standard Standard Standard
C/O Marking on Rotor MALAYSIA JAPAN
Remarks CDG on rotor
*Category A : Ordinary Production (Stock Item) ; Category B : Order Based Production
NH Basic Mechanical Series (3 Hands/Date) - Window Variation List Date : 20.10.2016

Reference NH15A12WMN NH15A12WMNL NH35A32MN NH35A32MN07

Product Line NH Basic Mechanical Series NH Basic Mechanical Series NH Basic Mechanical Series NH Basic Mechanical Series

Function 3 Hands/Date 3 Hands/Date 3 Hands/Date 3 Hands/Date

Appearance

Size 10 1/2''' 10 1/2''' 12''' 12'''

*Category B B B B
Spec Sheet Dial Drawing No. NH15 Dial - 2 NH15 Dial - 2 NH35 Dial - 1 NH35 Dial - 1
Postion Stem 3H 3H 3H 3H
Date 6H 6H 6H 6H
Date Disc Color White base Black letter White base Black letter White base Black letter White base Black letter
Hands Fitting Type Hands : TYPE M Hands : TYPE M Hands : TYPE M Hands : TYPE M
Stem Type Standard Long Standard Standard
C/O Marking on Rotor
Remarks CDG on rotor
*Category A : Ordinary Production (Stock Item) ; Category B : Order Based Production
NH Basic Mechanical Series (3 Hands/Date) - Window Variation List Date : 20.10.2016

Reference NH35A42J NH35A42MN NH35A42MN07 NH05A12MNB

Product Line NH Basic Mechanical Series NH Basic Mechanical Series NH Basic Mechanical Series NH Basic Mechanical Series

Function 3 Hands/Date 3 Hands/Date 3 Hands/Date 3 Hands/Date

Appearance

Size 12''' 12''' 12''' 7 3/4'''

*Category B B B B
Spec Sheet Dial Drawing No. NH35 Dial - 1 NH35 Dial - 1 NH35 Dial - 1 NH05 Dial - 2
Postion Stem 3H 3H 3H 3H
Date 6H 6H 6H 6H
Date Disc Color White base Black letter White base Black letter White base Black letter Black base White letter
Hands Fitting Type Hands : TYPE L Hands : TYPE L Hands : TYPE L Hands : TYPE M
Stem Type Standard Standard Standard Standard
C/O Marking on Rotor JAPAN
Remarks CDG on rotor
*Category A : Ordinary Production (Stock Item) ; Category B : Order Based Production
NH Basic Mechanical Series (3 Hands/Date) - Window Variation List Date : 20.10.2016

Reference NH35A32JB05 NH35A32MNB NH35A42MNB

Product Line NH Basic Mechanical Series NH Basic Mechanical Series NH Basic Mechanical Series

Function 3 Hands/Date 3 Hands/Date 3 Hands/Date

Appearance

Size 12''' 12''' 12'''

*Category B B B
Spec Sheet Dial Drawing No. NH35 Dial - 1 NH35 Dial - 1 NH35 Dial - 1
Postion Stem 3H 3H 3H
Date 6H 6H 6H
Date Disc Color Black base White letter Black base White letter Black base White letter
Hands Fitting Type Hands : TYPE M Hands : TYPE M Hands : TYPE L
Stem Type Standard Standard Standard
C/O Marking on Rotor JAPAN
Remarks CDG on rotor
*Category A : Ordinary Production (Stock Item) ; Category B : Order Based Production