Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                

Philips 32pfl2507

Download as pdf or txt
Download as pdf or txt
You are on page 1of 78

32” LCD TV

chassis PL12.2

Service Manual Contents


TYPE A
32PFL4507/F7 PHILIPS (Serial No.: DS1)
32PFL4507/F8 PHILIPS (Serial No.: XA1)
32PFL4507/F8 PHILIPS (Serial No.: DS1)

TYPE B
32PFL4907/F7 PHILIPS (Serial No.: DS1)

Thisservice
This servicemanual
manualcontains
containsinformation
informationofofdifferent
differenttypes
typesofofmodels.
models.
Makesure
Make suretotorefer
refertotothe
thesection
sectiondescribing
describingyour
yourmodel.
model.

© 2012 Funai Electric Co., Ltd.

All rights reserved. No part of this manual may be reproduced, copied, transmitted, disseminated, transcribed,
downloaded or stored in any storage medium, in any form or for any purpose without the express prior written
consent of Funai. Furthermore, any unauthorized commercial distribution of this manual or any revision hereto
is strictly prohibited.

Information in this document is subject to change without notice. Funai reserves the right to change the content
herein without the obligation to notify any person or organization of such changes.

with the design is a registered trademark of Funai Electric Co., Ltd and may not be used in any way
without the express written consent of Funai. All other trademarks used herein remain the exclusive property of
their respective owners. Nothing contained in this manual should be construed as granting, by implication or
otherwise, any license or right to use any of the trademarks displayed herein. Misuse of any trademarks or any
other content in this manual is strictly prohibited. Funai shall aggressively enforce its intellectual property rights
to the fullest extent of the law.

120523
IMPORTANT SAFETY NOTICE
Proper service and repair is important to the safe, reliable operation of all
P&F Equipment. The service procedures recommended by P&F and
described in this service manual are effective methods of performing
service operations. Some of these service special tools should be used
when and as recommended.
It is important to note that this service manual contains various CAUTIONS
and NOTICES which should be carefully read in order to minimize the risk
of personal injury to service personnel. The possibility exists that improper
service methods may damage the equipment. It also is important to
understand that these CAUTIONS and NOTICES ARE NOT EXHAUSTIVE.
P&F could not possibly know, evaluate and advice the service trade of all
conceivable ways in which service might be done or of the possible
hazardous consequences of each way. Consequently, P&F has not
undertaken any such broad evaluation. Accordingly, a servicer who uses a
service procedure or tool which is not recommended by P&F must first use
all precautions thoroughly so that neither his safety nor the safe operation
of the equipment will be jeopardized by the service method selected.

The LCD panel is manufactured to provide many years of useful life.


Occasionally a few non active pixels may appear as a tiny spec of color.
This is not to be considered a defect in the LCD screen.
TABLE OF CONTENTS
Specifications [TYPE A] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
[TYPE B] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
Important Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
Standard Notes for Servicing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
Cabinet Disassembly Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
Electrical Adjustment Instructions [TYPE A] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
[TYPE B] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-4
How to Initialize the LCD TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1
Firmware Renewal Mode [TYPE A] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1
[TYPE B] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-3
Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1
Block Diagrams [TYPE A] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-1
[TYPE B] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-6
Schematic Diagrams / CBA and Test Points . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-1
Wiring Diagrams [TYPE A] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-1
[TYPE B] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-2
Exploded Views [TYPE A]. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-1
[TYPE B]. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-2
Parts List [TYPE A] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-1
[TYPE B] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-4
Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-1
SPECIFICATIONS
[TYPE A]
< TUNER / NTSC >
ANT. Input ---------------------- 75 Ω Unbal., F type
Description Condition Unit Nominal Limit
1. AFT Pull-In Range --- MHz ±2.3 ±2.1
TV.ch.4 dBµ 18 20
2. Synchronizing Sens. CA.ch.31 dBµ 18 20
CA.ch.87 dBµ 18 23

< TUNER / ATSC >


Description Condition Unit Nominal Limit
1. Received Freq. Range (-28dBm) --- kHz --- ±100
ch.4 dBm --- -76/0
2. ATSC Dynamic Range (min / max) ch.10 dBm --- -76/0
ch.41 dBm --- -76/+4

< LCD PANEL >


Description Condition Unit Nominal Limit
Horizontal pixels 1366 ---
1. Native Pixel Resolution
Vertical pixels 768 ---
2. Brightness (w / filter) --- cd/m2 300 ---
Horizontal ° -85 to 85 ---
3. Viewing Angle
Vertical ° -85 to 85 ---

< VIDEO >


Description Condition Unit Nominal Limit
Horizontal % 5 5±5
1. Over Scan
Vertical % 5 5±5
--- °K 12000 ---
2. Color Temperature x 0.272 ±3%
y 0.278 ±3%
Horizontal line 400 ---
3. Resolution (composite video)
Vertical line 350 ---

< AUDIO >


All items are measured across 8 Ω load at speaker output terminal with L.P.F.
Description Condition Unit Nominal Limit
1. Audio MAX Output (ATSC 0dBfs) Lch/Rch W 8.0/8.0 7.0/7.0
2. Audio Distortion (NTSC) 500mW: Lch/Rch % 0.5/0.5 2.0/2.0

1-1 PL12.2SP
[TYPE B]
< TUNER / NTSC >
ANT. Input ---------------------- 75 Ω Unbal., F type
Description Condition Unit Nominal Limit
1. AFT Pull-In Range TV.ch.4 MHz ±2.3 ±2.1
TV.ch.4 dBµ 18 20
2. Synchronizing Sens. CA.ch.31 dBµ 18 20
CA.ch.87 dBµ 18 23

< TUNER / ATSC >


Description Condition Unit Nominal Limit
1. Received Freq. Range (-28dBm) --- kHz --- ±100
ch.4 dBm --- -76/0
2. ATSC Dynamic Range (min / max) ch.10 dBm --- -76/0
ch.41 dBm --- -76/+4

< LCD PANEL >


Description Condition Unit Nominal Limit
Horizontal pixels 1366 ---
1. Native Pixel Resolution
Vertical pixels 768 ---
2. Brightness (w / filter) --- cd/m2 300 ---
Horizontal ° -88 to 88 ---
3. Viewing Angle
Vertical ° -88 to 88 ---

< VIDEO >


Description Condition Unit Nominal Limit
Horizontal % 5 5±5
1. Over Scan
Vertical % 5 5±5
--- °K 12000 ---
2. Color Temperature x 0.272 ±4%
y 0.278 ±4.5%
Horizontal line 400 ---
3. Resolution (composite video)
Vertical line 350 ---

< AUDIO >


All items are measured across 8 Ω load at speaker output terminal with L.P.F.
Description Condition Unit Nominal Limit
1. Audio Output 10% Distortion
Lch/Rch W 8.0/8.0 7.0/7.0
(ATSC 0dBfs)
2. Audio Distortion (NTSC) 500mW: Lch/Rch % 0.5/0.5 2.0/2.0
-6dB : Lch Hz
3. Audio Freq. Response ( NTSC) 70 to 10k ---
-6dB : Rch Hz

1-2 PL12.2SP
IMPORTANT SAFETY PRECAUTIONS
Prior to shipment from the factory, our products are strictly inspected for recognized product safety and electrical
codes of the countries in which they are to be sold. However, in order to maintain such compliance, it is equally
important to implement the following precautions when a set is being serviced.

Safety Precautions for LCD TV d. Leakage Current Hot Check - With the
instrument completely reassembled, plug the
Circuit AC line cord directly into a 120 V AC outlet. (Do
1. Before returning an instrument to the not use an isolation transformer during this
customer, always make a safety check of the test.) Use a leakage current tester or a
entire instrument, including, but not limited to, the metering system that complies with American
following items: National Standards Institute (ANSI) C101.1
a. Be sure that no built-in protective devices are Leakage Current for Appliances and
defective and have been defeated during Underwriters Laboratories (UL) 1410, (50.7).
servicing. (1) Protective shields are provided With the instrument AC switch first in the on
on this chassis to protect both the technician position and then in the off position, measure
and the customer. Correctly replace all missing from a known earth ground (metal water pipe,
protective shields, including any removed for conduit, etc.) to all exposed metal parts of the
servicing convenience. (2) When reinstalling instrument (antennas, handle brackets, metal
the chassis and/or other assembly in the cabinet, screw heads, metallic overlays, control
cabinet, be sure to put back in place all shafts, etc.), especially any exposed metal
protective devices, including but not limited to, parts that offer an electrical return path to the
nonmetallic control knobs, insulating chassis. Any current measured must not
fishpapers, adjustment and compartment exceed 0.5 milli-ampere. Reverse the
covers/shields, and isolation resistor/capacitor instrument power cord plug in the outlet and
networks. Do not operate this instrument or repeat the test.
permit it to be operated without all
protective devices correctly installed and READING SHOULD
functioning. Servicers who defeat safety NOT BE ABOVE 0.5 mA
features or fail to perform safety checks
may be liable for any resulting damage. LEAKAGE
DEVICE CURRENT
b. Be sure that there are no cabinet openings BEING TESTER
through which an adult or child might be able to TESTED + _
insert their fingers and contact a hazardous
voltage. Such openings include, but are not TEST ALL EXPOSED
limited to, (1) spacing between the Liquid METAL SURFACES
Crystal Panel and the cabinet mask, (2)
excessively wide cabinet ventilation slots, and
(3) an improperly fitted and/or incorrectly ALSO TEST WITH
secured cabinet back cover. PLUG REVERSED
c. Antenna Cold Check - With the instrument AC USING AC
plug removed from any AC source, connect an ADAPTER PLUG EARTH
electrical jumper across the two AC plug AS REQUIRED GROUND
prongs. Place the instrument AC switch in the
on position. Connect one lead of an ohmmeter ANY MEASUREMENTS NOT WITHIN THE
to the AC plug prongs tied together and touch LIMITS SPECIFIED HEREIN INDICATE A
the other ohmmeter lead in turn to each tuner POTENTIAL SHOCK HAZARD THAT MUST
antenna input exposed terminal screw and, if BE ELIMINATED BEFORE RETURNING THE
applicable, to the coaxial connector. If the INSTRUMENT TO THE CUSTOMER OR
measured resistance is less than 1.0 megohm BEFORE CONNECTING THE ANTENNA OR
or greater than 5.2 megohm, an abnormality ACCESSORIES.
exists that must be corrected before the
2. Read and comply with all caution and safety-
instrument is returned to the customer. Repeat
related notes on or inside the receiver cabinet, on
this test with the instrument AC switch in the off
the receiver chassis, or on the Liquid Crystal
position.
Panel.

2-1 LTVN_ISP
3. Design Alteration Warning - Do not alter or add 7. Product Safety Notice - Some electrical and
to the mechanical or electrical design of this TV mechanical parts have special safety-related
receiver. Design alterations and additions, characteristics which are often not evident from
including, but not limited to circuit modifications visual inspection, nor can the protection they give
and the addition of items such as auxiliary audio necessarily be obtained by replacing them with
and/or video output connections, might alter the components rated for higher voltage, wattage, etc.
safety characteristics of this receiver and create a Parts that have special safety characteristics are
hazard to the user. Any design alterations or identified by a # on schematics and in parts lists.
additions will void the manufacturer's warranty and Use of a substitute replacement that does not
may make you, the servicer, responsible for have the same safety characteristics as the
personal injury or property damage resulting recommended replacement part might create
therefrom. shock, fire, and/or other hazards. The product's
4. Hot Chassis Warning - safety is under review continuously and new
instructions are issued whenever appropriate.
a. Some TV receiver chassis are electrically
Prior to shipment from the factory, our products
connected directly to one conductor of the AC
are strictly inspected to confirm they comply with
power cord and maybe safety-serviced without
the recognized product safety and electrical codes
an isolation transformer only if the AC power
of the countries in which they are to be sold.
plug is inserted so that the chassis is
However, in order to maintain such compliance, it
connected to the ground side of the AC power
is equally important to implement the following
source. To confirm that the AC power plug is
precautions when a set is being serviced.
inserted correctly, with an AC voltmeter,
measure between the chassis and a known
earth ground. If a voltage reading in excess of
1.0 V is obtained, remove and reinsert the AC
power plug in the opposite polarity and again
measure the voltage potential between the
chassis and a known earth ground.
b. Some TV receiver chassis normally have 85V
AC(RMS) between chassis and earth ground
regardless of the AC plug polarity. This chassis
can be safety-serviced only with an isolation
transformer inserted in the power line between
the receiver and the AC power source, for both
personnel and test equipment protection.
c. Some TV receiver chassis have a secondary
ground system in addition to the main chassis
ground. This secondary ground system is not
isolated from the AC power line. The two
ground systems are electrically separated by
insulation material that must not be defeated or
altered.
5. Observe original lead dress. Take extra care to
assure correct lead dress in the following areas: a.
near sharp edges, b. near thermally hot parts-be
sure that leads and components do not touch
thermally hot parts, c. the AC supply, d. high
voltage, and, e. antenna wiring. Always inspect in
all areas for pinched, out of place, or frayed wiring.
Check AC power cord for damage.
6. Components, parts, and/or wiring that appear to
have overheated or are otherwise damaged
should be replaced with components, parts, or
wiring that meet original specifications.
Additionally, determine the cause of overheating
and/or damage and, if necessary, take corrective
action to remove any potential safety hazard.

2-2 LTVN_ISP
Precautions during Servicing
A. Parts identified by the # symbol are critical for
safety.
Replace only with part number specified.
B. In addition to safety, other parts and assemblies
are specified for conformance with regulations
applying to spurious radiation. These must also be
replaced only with specified replacements.
Examples: RF converters, RF cables, noise
blocking capacitors, and noise blocking filters, etc.
C. Use specified internal wiring. Note especially:
1) Wires covered with PVC tubing
2) Double insulated wires
3) High voltage leads
D. Use specified insulating materials for hazardous
live parts. Note especially:
1) Insulation Tape
2) PVC tubing
3) Spacers
4) Insulators for transistors.
E. When replacing AC primary side components
(transformers, power cord, etc.), wrap ends of
wires securely about the terminals before
soldering.
F. Observe that the wires do not contact heat
producing parts (heat sinks, oxide metal film
resistors, fusible resistors, etc.)
G. Check that replaced wires do not contact sharp
edged or pointed parts.
H. When a power cord has been replaced, check that
11~13 lb (5~6 kg) of force in any direction will not
loosen it.
I. Also check areas surrounding repaired locations.
J. Use care that foreign objects (screws, solder
droplets, etc.) do not remain inside the set.
K. When connecting or disconnecting the internal
connectors, first, disconnect the AC plug from the
AC supply outlet.
L. When installing parts or assembling the cabinet
parts, be sure to use the proper screws and
tighten certainly.

2-3 LTVN_ISP
Safety Check after Servicing
Examine the area surrounding the repaired location for damage or deterioration. Observe that screws, parts and
wires have been returned to original positions. Afterwards, perform the following tests and confirm the specified
values in order to verify compliance with safety standards.

1. Clearance Distance
When replacing primary circuit components, confirm
specified clearance distance (d) and (d') between
soldered terminals, and between terminals and Chassis or Secondary Conductor
surrounding metallic parts. (See Fig. 1)
Primary Circuit
Table 1: Ratings for selected area

Clearance d' d
AC Line Voltage Region
Distance (d), (d’)
U.S.A. or ≥ 3.2 mm
110 to 130 V
Canada (0.126 inches)

Note: This table is unofficial and for reference only. Be


sure to confirm the precise values.

Fig. 1

2. Leakage Current Test


Confirm the specified (or lower) leakage current
between B (earth ground, power cord plug prongs) and
externally exposed accessible parts (RF terminals, Exposed Accessible Part
antenna terminals, video and audio input and output
terminals, microphone jacks, earphone jacks, etc.) is
Z
lower than or equal to the specified value in the table
below.
Measuring Method: (Power ON) AC Voltmeter
(High Impedance)
Insert load Z between B (earth ground, power cord plug
prongs) and exposed accessible parts. Use an AC
voltmeter to measure across both terminals of load Z.
See Fig. 2 and following table.
Earth Ground
B
Power Cord Plug Prongs

Fig. 2

Table 2: Leakage current ratings for selected areas

AC Line Voltage Region Load Z Leakage Current (i) Earth Ground (B) to:
U.S.A. or 0.15 µF CAP. & 1.5 kΩ Exposed accessible
110 to 130 V i ≤ 0.5 mA rms
Canada RES. Connected in parallel parts

Note: This table is unofficial and for reference only. Be sure to confirm the precise values.

2-4 LTVN_ISP
STANDARD NOTES FOR SERVICING
Circuit Board Indications How to Remove / Install Flat Pack-IC
1. The output pin of the 3 pin Regulator ICs is
1. Removal
indicated as shown.
With Hot-Air Flat Pack-IC Desoldering Machine:
Top View Bottom View 1. Prepare the hot-air flat pack-IC desoldering
Input machine, then apply hot air to the Flat Pack-IC
Out In (about 5 to 6 seconds). (Fig. S-1-1)

2. For other ICs, pin 1 and every fifth pin are


indicated as shown.

Pin 1

10

3. The 1st pin of every male connector is indicated as Fig. S-1-1


shown.
2. Remove the flat pack-IC with tweezers while
applying the hot air.
Pin 1 3. Bottom of the flat pack-IC is fixed with glue to the
CBA; when removing entire flat pack-IC, first apply
soldering iron to center of the flat pack-IC and heat
Pb (Lead) Free Solder up. Then remove (glue will be melted). (Fig. S-1-6)
4. Release the flat pack-IC from the CBA using
Pb free mark will be found on PCBs which use Pb tweezers. (Fig. S-1-6)
free solder. (Refer to figure.) For PCBs with Pb free
mark, be sure to use Pb free solder. For PCBs CAUTION:
without Pb free mark, use standard solder. 1. The Flat Pack-IC shape may differ by models. Use
an appropriate hot-air flat pack-IC desoldering
machine, whose shape matches that of the Flat
Pack-IC.
2. Do not supply hot air to the chip parts around the
flat pack-IC for over 6 seconds because damage
to the chip parts may occur. Put masking tape
around the flat pack-IC to protect other parts from
damage. (Fig. S-1-2)
Pb free mark

3-1 TVN_SN
3. The flat pack-IC on the CBA is affixed with glue, so With Soldering Iron:
be careful not to break or damage the foil of each 1. Using desoldering braid, remove the solder from
pin or the solder lands under the IC when all pins of the flat pack-IC. When you use solder
removing it. flux which is applied to all pins of the flat pack-IC,
you can remove it easily. (Fig. S-1-3)

Hot-air
Flat Pack-IC Flat Pack-IC Desoldering Braid
Desoldering
Machine
CBA

Soldering Iron
Masking Flat Pack-IC Fig. S-1-3
Tape
Tweezers 2. Lift each lead of the flat pack-IC upward one by
one, using a sharp pin or wire to which solder will
Fig. S-1-2
not adhere (iron wire). When heating the pins, use
a fine tip soldering iron or a hot air desoldering
machine. (Fig. S-1-4)

Sharp
Pin

Fine Tip
Soldering Iron
Fig. S-1-4

3. Bottom of the flat pack-IC is fixed with glue to the


CBA; when removing entire flat pack-IC, first apply
soldering iron to center of the flat pack-IC and heat
up. Then remove (glue will be melted). (Fig. S-1-6)
4. Release the flat pack-IC from the CBA using
tweezers. (Fig. S-1-6)

3-2 TVN_SN
With Iron Wire: 2. Installation
1. Using desoldering braid, remove the solder from 1. Using desoldering braid, remove the solder from
all pins of the flat pack-IC. When you use solder the foil of each pin of the flat pack-IC on the CBA
flux which is applied to all pins of the flat pack-IC, so you can install a replacement flat pack-IC more
you can remove it easily. (Fig. S-1-3) easily.
2. Affix the wire to a workbench or solid mounting 2. The “ I ” mark on the flat pack-IC indicates pin 1.
point, as shown in Fig. S-1-5. (See Fig. S-1-7.) Be sure this mark matches the
3. While heating the pins using a fine tip soldering pin 1 on the PCB when positioning for installation.
iron or hot air blower, pull up the wire as the solder Then presolder the four corners of the flat pack-IC.
melts so as to lift the IC leads from the CBA (See Fig. S-1-8.)
contact pads as shown in Fig. S-1-5. 3. Solder all pins of the flat pack-IC. Be sure that
4. Bottom of the flat pack-IC is fixed with glue to the none of the pins have solder bridges.
CBA; when removing entire flat pack-IC, first apply
soldering iron to center of the flat pack-IC and heat
up. Then remove (glue will be melted). (Fig. S-1-6) Example :
5. Release the flat pack-IC from the CBA using
tweezers. (Fig. S-1-6)
Note: When using a soldering iron, care must be
taken to ensure that the flat pack-IC is not
being held by glue. When the flat pack-IC is
removed from the CBA, handle it gently
because it may be damaged if force is applied.
Pin 1 of the Flat Pack-IC
is indicated by a " " mark.
Hot Air Blower Fig. S-1-7

or
Presolder

Iron Wire

Soldering Iron

To Solid
Mounting Point
Fig. S-1-5
Flat Pack-IC

CBA

Fine Tip Fig. S-1-8


CBA Soldering Iron

Flat Pack-IC
Tweezers

Fig. S-1-6

3-3 TVN_SN
Instructions for Handling Semi-
conductors
Electrostatic breakdown of the semi-conductors may
occur due to a potential difference caused by
electrostatic charge during unpacking or repair work.

1. Ground for Human Body


Be sure to wear a grounding band (1 MΩ) that is
properly grounded to remove any static electricity that
may be charged on the body.

2. Ground for Workbench


Be sure to place a conductive sheet or copper plate
with proper grounding (1 MΩ) on the workbench or
other surface, where the semi-conductors are to be
placed. Because the static electricity charge on
clothing will not escape through the body grounding
band, be careful to avoid contacting semi-conductors
with your clothing.

<Incorrect>

CBA

<Correct> Grounding Band

1MΩ

CBA

1MΩ
Conductive Sheet or
Copper Plate

3-4 TVN_SN
CABINET DISASSEMBLY INSTRUCTIONS
1. Disassembly Flowchart Step/
Fig.
Loc. Part Removal Note
This flowchart indicates the disassembly steps for the No.
No.
cabinet parts and the CBA in order to gain access to
items to be serviced. When reassembling, follow the LCD
[10] D4 --------------- 1,3
steps in reverse order. Bend, route and dress the Module
cables as they were. Front
[11] D4 --------------- 3
Cabinet
[2] Stand
[1] Rear Cover [3] Speaker
Assembly
↓ ↓ ↓ ↓ ↓
(1) (2) (3) (4) (5)
[7] Function
[4] Stand Holder
CBA *1: TYPE A
[5] Power Supply *2: TYPE B
CBA
Note:
[6] Digital Main (1) Order of steps in procedure. When reassembling,
CBA Unit
follow the steps in reverse order. These numbers
[8] LCD Panel are also used as the Identification (location) No. of
Assembly parts in figures.
(2) Parts to be removed or installed.
[9] Rear Frame (3) Fig. No. showing procedure of part location
(4) Identification of parts to be removed, unhooked,
[10] LCD Module unlocked, released, unplugged, unclamped, or
desoldered.
[11] Front P = Spring, L = Locking Tab, S = Screw,
Cabinet H = Hex Screw, CN = Connector
e.g. 2(S-2) = two Screws of (S-2),
2. Disassembly Method 2(L-2) = two Locking Tabs of (L-2)
(5) Refer to the following "Reference Notes in the
Step/ Table."
Fig.
Loc. Part Removal Note
No.
No. Precautions concerning the LCD Panel
[1] Rear Cover D1 6(S-1), 6(S-2) --- Assembly:
Stand 1. When you disassemble the LCD Panel
[2] D1 3(S-3) ---
Assembly Assembly
D2 • Be careful not to scratch the Reflection Sheet with
[3] Speaker CN3801 ---
D5 the edge of Rear Frame when disassembling/
Stand 4(S-4), 2(S-5), 2(S-6), re-assembling it.
[4] D2 ---
Holder CN601, Stand Bracket • Be careful not to drop any plastic chip on the
Reflection Sheet when/after you remove the Screws.
Power
D3 4(S-7), CN631, • Prohibit to put any external pressure on the
[5] Supply ---
D5 CN1001
CBA Reflection Sheet because the scratch on the back of
the Reflection Sheet have direct repercussion on the
3(S-8), CN3006*1,
display screen.
Digital Main D3 CN3904*2, CN3101*1,
[6] ---
CBA Unit D5 CN3105*2, • Prohibit to put any external pressure on the Sheet
Jack Holder Holder or LED Heat Sink Assembly either because it
also has repercussion on the display screen via the
Function D3
[7] Sensor Plate 2,3 Reflection Sheet.
CBA D5
• You need to remove any visible dust from the
LCD Panel Reflection Sheet which creates the external
[8] D3 --------------- 3
Assembly pressure between the Reflection Sheet and the
[9] Rear Frame D4 12(S-9), 2(S-10) 1,3 Sheet Holder/LED Heat Sink Assembly as a result.

4-1 PL12.2-A_DC
• To prevent the Screw from being stripped, the screw between the Front Cabinet and Function CBA will
tightening torque should be 13.23 lbf·in(6 kgf·cm) for impair the sensor sensitivity.)
the Rear Frame Screw and 5.512 lbf·in(2.5 kgf·cm) • Prepare for substitutional Function CBA in case you
for the LED Heat Sink Assembly Screw. break it when you detach it from the Front Cabinet.
• Do not pull the FFC Cable and Board Cable
forcefully when you re-assemble. 3. Performance Test after reassembling the LCD
Panel Assembly
2. When you disassemble/re-assemble the • After you swap any of the Front Cabinet, Rear Frame
Function CBA on the Front Cabinet or Function CBA, you need to make sure that there
• Detach the Function CBA, which is attached on the is no Gomikami/Black Spot with foreign material or
Front Cabinet with double-sided tape, without Mura/White Spot on the display screen.
breaking it. • Make sure there is no malfunction on the display
• When you put the Function CBA back on the New screen by checking the White Mode and White 20%
Front Cabinet, you need to use specified new Mode in the Purity Check Mode.
double-sided tape and put the Function CBA onto • Check the operational sensitivity on Touch Sensor
the New Front Cabinet with equal pressure to the Control Panel to make sure everything functions
Board. (The gap more than 0.015 inch (0.4 mm) normally.

[1] Rear Cover

(S-1)

(S-1)

(S-2)

[2] Stand Assembly

(S-3)
Fig. D1

4-2 PL12.2-A_DC
[4] Stand Holder
Stand Bracket

(S-5)

(S-6)
(S-4)
(S-5)
[3] Speaker
(S-6)
Fig. D2

[8] LCD Panel Assembly*1

[6] Digital Main CBA Unit


Jack Holder

Sensor Plate
Double-sided tape
(S-8)
[7] Function CBA*1

(S-7)
[5] Power Supply CBA
Fig. D3
*1: Make sure to read all the precautions on page 4-1, 4-2 when you disassemble/re-assemble
the LCD Panel Assembly.

4-3 PL12.2-A_DC
[11] Front Cabinet*1

[9] Rear Frame*1


Sheet Holder
FFC Cable
(S-9)
FFC Cable
(S-9)

(S-9)

(S-9)
LED Heat Sink Assembly

Sheet Holder
(S-9)
(S-10)
[10] LCD Module *1

Fig. D4
*1: Make sure to read all the precautions on page 4-1, 4-2 when you disassemble/re-assemble
the LCD Panel Assembly.

4-4 PL12.2-A_DC
TV Cable Wiring Diagram

To LCD Panel To LCD Panel


Assembly Assembly

Digital Main
Power Supply CBA CBA Unit

CN1001
*1 CN3006
CN631
*2 CN3904

*1 CN3701
*2 CN3601

CN601

*1 CN3101 CN3801

To AC Cord *2 CN3105

To Speaker
Function CBA
CN4001
*1: TYPE A
*2: TYPE B

Fig. D5

4-5 PL12.2-A_DC
ELECTRICAL ADJUSTMENT INSTRUCTIONS
[TYPE A]
General Note: “CBA” is abbreviation for How to set up the service mode:
“Circuit Board Assembly.”
Note: Electrical adjustments are required after
Service mode:
replacing circuit components and certain 1. Turn the power on.
mechanical parts. It is important to perform 2. Press [MENU] button to display Setup menu.
these adjustments only after all repairs and 3. Select “Features”.
replacements have been completed.
4. Select “Software Upgrade”.
Also, do not attempt these adjustments unless
the proper equipment is available. 5. Select “Current Software Info”.
6. Press [0], [6], [2], [5], [9], [6] and [INFO] buttons on
Test Equipment Required the remote control unit in this order. The following
1. Remote control unit screen appears.
2. Color Analyzer, "*" differs depending on the models.
CA-310 (KONICA MINOLTA Luminance meter) or
Code: *******-**-**-****-**
measuring instrument as good as CA-310. Pic code: ***-*****-***-***-*-**
Panel-Option code: **-***-***-***-***
MIPS: Push 0 key

Press "POWER" key to exit.

Safety: Safety_Non
HDMI EDID: **
HDMI UART: OFF Total Watch Time: *****
Touch Sensor Ver: -.-- / --- Lightsensor: **

5-1 PL12.2_A (LC10)EA


1. Purity Check Mode 2. VCOM Adjustment
This mode cycles through full-screen displays of red, Test Point Adj. Point
green, blue, and white to check for non-active pixels. [CHANNEL UP/DOWN]
Screen
1. Enter the service mode. buttons
2. Each time the [7] button on the remote control unit M. EQ. Spec.
is pressed, the display changes as follows. Color analyzer See below
Purity Check Mode Figure

White mode To avoid interference from ambient


light, this adjustment should be
[7] button performed in a dark room.

Perpendicularity

[7] button
Black mode

Color Analyzer

[7] button
1. Set the color analyzer at the zero point calibration
White 50% mode
and bring the optical receptor pointing at the
center of the LCD-Panel.
Note: The optical receptor must be set
perpendicularly to the LCD Panel surface.
2. Enter the service mode.
[7] button 3. Press [2] button on the remote control unit.
Red, Green, Blue mode 4. Press [CHANNEL UP/DOWN] buttons on the
remote control unit so that the color analyzer value
becomes minimum.
5. To cancel or to exit from the VCOM Adjustment,
press [CH RETURN] or [PREV CH] button.

[7] button Note:


V-ramp mode Execute the VCOM adjustment within 2 minutes after
you turn the power on.

[7] button
White 20% mode

Note:
When entering this mode, the default setting is White mode.

3. To cancel or to exit from the Purity Check Mode,


press [CH RETURN] or [PREV CH] button.

5-2 PL12.2_A (LC10)EA


The White Balance Adjustment should be 6. Press [MENU] button. The internal Raster signal
performed when replacing the LCD Panel appears in the screen. (“Internal (Single)” appears
in the upper right of the screen as shown below.)
or Digital Main CBA.
3. White Balance Adjustment
Internal (Single)
Purpose: To mix red and blue beams correctly for
pure white.
Symptom of Misadjustment: White becomes bluish
or reddish.

ITEM SPECIFICATION HDB 0

x= 0.272 ± 0.002
Color temperature
y= 0.278 ± 0.002
7. Press [CHANNEL UP/DOWN] buttons to adjust
Internal pattern
Input Signal the color temperature becomes 12000°K
(40/80% raster)
(x= 0.272 / y= 0.278 ± 0.002).
Measurement point Screen center
8. Press [1] button to select the “HDR” for High Drive
CA-310 (KONICA MINOLTA Red adjustment (“HDR” appears in the screen.)
Luminance meter) or and press [CHANNEL UP/DOWN] buttons to
M. EQ.
measuring instrument as adjust the color temperature.
good as CA-310.
9. If necessary, adjust the “HDB” or “HDR” again.
60min.
10. Press [6] button to select the “LDB” for Low Drive
Aging time (Retail MODE/100IRE Raster
HDMI 1080i@60) Blue adjustment (“LDB” appears in the screen.)
and press [CHANNEL UP/DOWN] buttons to
Shipment setting/ adjust the color temperature.
MODE setting of TV
Retail MODE
Ambient
25°C ± 5°C
temperature Internal (Single)

1. Operate the unit for more than 60 minutes.


2. Enter the service mode.
3. Press [VOLUME DOWN] button three times on the
remote control unit to select “Drive setting” mode.
“Drive” appears in the screen. LDB 0

4. Set the color analyzer at the CHROMA mode and


zero point calibration. Bring the optical receptor
pointing at the center of the LCD-Panel. 11. Press [4] button to select the “LDR” for Low Drive
Red adjustment (“LDR” appears in the screen.) and
To avoid interference from ambient press [CHANNEL UP/DOWN] buttons to adjust the
light, this adjustment should be color temperature.
performed in a dark room.
12. If necessary, adjust the “LDB” or “LDR” again.
Perpendicularity
13. Press [VOLUME DOWN] button to shift to the
“Debugging Message” mode.
If there is no message under “[WB]” section, this
adjustment completes.
If “Drive settings are NG. Retry.” is displayed,
repeat above steps from 5. to 12. Then check
Color Analyzer “Debugging Message” again. If “Drive settings are
NG. Retry.” is displayed, replace the LCD Panel or
Digital Main CBA.
Note: The optical receptor must be set 14. To cancel or to exit from the White Balance
perpendicularly to the LCD Panel surface. Adjustment, press [CH RETURN] or [PREV CH]
5. Press [3] button to select the “HDB” for High Drive button.
Blue adjustment. (“HDB” appears in the screen.)

5-3 PL12.2_A (LC10)EA


[TYPE B]
General Note: “CBA” is abbreviation for How to set up the service mode:
“Circuit Board Assembly.”
Note: Electrical adjustments are required after
Service mode:
replacing circuit components and certain 1. Turn the power on.
mechanical parts. It is important to perform 2. Press [0], [6], [2], [5], [9], [6], and [INFO] buttons
these adjustments only after all repairs and on the remote control unit in this order. The
replacements have been completed. following screen appears.
Also, do not attempt these adjustments unless
the proper equipment is available. "*" differs depending on the models.

[current]
Test Equipment Required File code: ***-****_***_*
Total checksum: Push "0" key
1. Remote control unit Panel-Option code: **-***-***-***-***-***
***-***-***-***-***
2. Color Analyzer,
CA-310 (KONICA MINOLTA Luminance meter) or Press "POWER" key to exit.
measuring instrument as good as CA-310. MAC address: **:**:**:**:**:**
ESN: *****************************

Tuner: ****
HDMI UART: OFF TotalWatchTime: *****
Touch Sensor Ver: -.-- / --- SystemTime: **:**
EDID: Push "0" key Lightsensor: **

5-4 PL12.2_B (A27F5UH)_EA


1. Purity Check Mode 2. VCOM Adjustment
This mode cycles through full-screen displays of red, Test Point Adj. Point
green, blue, and white to check for non-active pixels. [CHANNEL UP/DOWN]
Screen
1. Enter the service mode. buttons
2. Each time the [7] button on the remote control unit M. EQ. Spec.
is pressed, the display changes as follows. Color analyzer See below
Purity Check Mode Figure

White mode To avoid interference from ambient


light, this adjustment should be
[7] button performed in a dark room.

Perpendicularity

[7] button
Black mode

Color Analyzer

[7] button
1. Set the color analyzer at the zero point calibration
White 50% mode
and bring the optical receptor pointing at the
center of the LCD-Panel.
Note: The optical receptor must be set
perpendicularly to the LCD Panel surface.
2. Enter the service mode.
[7] button 3. Press [2] button on the remote control unit.
Red, Green, Blue mode 4. Press [CHANNEL UP/DOWN] buttons on the
remote control unit so that the color analyzer value
becomes minimum.
5. To cancel or to exit from the VCOM Adjustment,
press [CH RETURN] or [PREV CH] button.

[7] button Note:


V-ramp mode Execute the VCOM adjustment within 2 minutes after
you turn the power on.

[7] button
White 20% mode

Note:
When entering this mode, the default setting is White mode.

3. To cancel or to exit from the Purity Check Mode,


press [CH RETURN] or [PREV CH] button.

5-5 PL12.2_B (A27F5UH)_EA


The White Balance Adjustment should be 5. Press [3] button to select the “HDB” for High Drive
performed when replacing the LCD Panel Blue adjustment. (“HDB” appears in the screen.)
or Digital Main CBA. 6. Press [MENU] button. The internal Raster signal
appears in the screen. (“Internal (Single)” appears
3. White Balance Adjustment in the upper right of the screen as shown below.)

Purpose: To mix red and blue beams correctly for


pure white.
Internal (Single)
Symptom of Misadjustment: White becomes bluish
or reddish.

ITEM SPECIFICATION
x= 0.272 ± 0.002
Color temperature HDB 0
y= 0.278 ± 0.002
Internal pattern
Input Signal
(30/50/80% raster)
7. Press [CHANNEL UP/DOWN] buttons to adjust
Measurement point Screen center
the color temperature becomes 12000°K
CA-310 (KONICA MINOLTA (x= 0.272 / y= 0.278 ± 0.002).
Luminance meter) or
M. EQ. 8. Press [1] button to select the “HDR” for High Drive
measuring instrument as
good as CA-310. Red adjustment (“HDR” appears in the screen.)
and press [CHANNEL UP/DOWN] buttons to
60min. adjust the color temperature.
Aging time (Retail MODE/100IRE Raster
HDMI 1080i@60) 9. If necessary, adjust the “HDB” or “HDR” again.
10. Press [6] button to select the “MDB” for Middle
Shipment setting/
MODE setting of TV Drive Blue adjustment (“MDB” appears in the
Retail MODE
screen.) and press [CHANNEL UP/DOWN] buttons
Ambient to adjust the color temperature.
25°C ± 5°C
temperature

1. Operate the unit for more than 60 minutes.


Internal (Single)
2. Enter the service mode.
3. Press [VOLUME DOWN] button three times on the
remote control unit to select “Drive setting” mode.
“Drive” appears in the screen.
4. Set the color analyzer at the CHROMA mode and
zero point calibration. Bring the optical receptor MDB 0

pointing at the center of the LCD-Panel.

To avoid interference from ambient 11. Press [4] button to select the “MDR” for Middle
light, this adjustment should be Drive Red adjustment (“MDR” appears in the
performed in a dark room.
screen.) and press [CHANNEL UP/DOWN] buttons
Perpendicularity to adjust the color temperature.
12. If necessary, adjust the “MDB” or “MDR” again.

Color Analyzer

Note: The optical receptor must be set


perpendicularly to the LCD Panel surface.

5-6 PL12.2_B (A27F5UH)_EA


13. Press [9] button to select the “LDB” for Low Drive
Blue adjustment (“LDB” appears in the screen.)
and press [CHANNEL UP/DOWN] buttons to
adjust the color temperature.

Internal (Single)

LDB 0

14. Press [7] button to select the “LDR” for Low Drive
Red adjustment (“LDR” appears in the screen.) and
press [CHANNEL UP/DOWN] buttons to adjust the
color temperature.
15. If necessary, adjust the “LDB” or “LDR” again.
16. Press [CH RETURN] or [PREV CH] to shift to the
initial screen in the service mode.
If [White Balance] message with a green color is
displayed on the upper right of the screen, this
adjustment completes.
If [White Balance] message with a red color is
displayed, repeat above steps from 5. to 15. Then
check the initial screen in the service mode again.
If [White Balance] message with a red color is
displayed, replace the LCD Panel or Digital Main
CBA.
17. To cancel or to exit from the White Balance
Adjustment, press [CH RETURN] or [PREV CH]
button.

5-7 PL12.2_B (A27F5UH)_EA


HOW TO INITIALIZE THE LCD TV
The purpose of initialization is to place the set in a new out of box condition. The customer will be prompted to
select a language and program channels after the set has been initialized.
To put the program back at the factory-default, initialize the LCD TV using the following procedure.

[TYPE A]
1. Turn the power on.
2. Enter the service mode.
- To cancel the service mode, press [ ] button on
the remote control unit.
3. Press [FREEZE] button on the remote control unit
to initialize the LCD television.
4. "INITIALIZED" will appear in the upper right of the
screen. "INITIALIZED" color will change to green
from red when initialization is completed.

[TYPE B]
1. Turn the power on.
2. Enter the service mode.
- To cancel the service mode, press [ ] button on
the remote control unit.
3. Press [COLOR(red)] button on the remote control
unit to initialize the LCD television.
4. "INITIALIZE" will appear in the upper right of the
screen. The whole screen color will change to
green and "INITIALIZE FINISH" will appear in the
center of the screen when initialization is
completed.

6-1 PL12.2_INT
FIRMWARE RENEWAL MODE
[TYPE A]
Equipment Required
a. USB storage device
b. Remote Control Unit

Firmware Update Procedure


User Upgrade (Filename example: TVNB012_00_UF_XX91_AA.ecc)
Upgrade the firmware only. The setting values will not be initialized.
The User Upgrade and the Firmware Upgrade (Factory Upgrade) will be done by the same file. If you want to
upgrade the firmware and initialize the setting values also, add “FACT_” at the beginning of the filename.
If you want to upgrade the firmware only and leave the setting values as they are, eliminate the “FACT_” from the
filename.

Update procedure
1. Turn the power on. 11. The update will start and the following will appear
2. Press [MENU] button to display Menu. in the screen.
3. Select “Features”. "*" differs depending on the models.

4. Select “Software Upgrade”. Software Upgrade

5. Select “Upgrade” to display Upgrade screen. Software upgrade in progress. Please wait.
6. Press [OK] button to display Software Upgrade Do not remove the USB storage device or
screen. turn the TV off while upgrade is in progress.
7. Select “USB” and press [OK] button. Current Version: *******-***-*-***-****
8. Insert the USB storage device to the USB port as New Version: *******-***-*-***-****
shown below. *1 Downloading...
0%
Rear Cabinet
Rear Cabinet
Note: If the above screen isn’t displayed, repeat from
USB port step 1.
USB port
The appearance shown in *1 is described as follows.
Appearance State
USB storage Downloading the firmware from
USB storage
device Downloading...
device the USB storage device.
Writing the downloaded firmware
Writing...
in flash memory.
Checking... Checking the new firmware.

12. When the firmware update is completed, the


following will appear in the screen.

Software Upgrade
9. Select “Check” and press [OK] button.
10. Select “Upgrade” and press [OK] button to start
software upgrade.

The software upgrade is completed.


Remove USB storage device, turn TV off then on again.

Remove the USB storage device from the USB


port.
Turn the power off and turn the power on again.

7-1 PL12.2_A FW
Factory Upgrade (Firmware Upgrade/Flash Upgrade)
Firmware Upgrade (Filename example: FACT_TVNB012_00_UF_XX91_AA.ecc)
Upgrade the firmware and initialize the setting values.
The User Upgrade and the Firmware Upgrade (Factory Upgrade) will be done by the same file. If you want to
upgrade the firmware and initialize the setting values also, add “FACT_” at the beginning of the filename.
If you want to upgrade the firmware only and leave the setting values as they are, eliminate the “FACT_” from the
filename.
Flash Upgrade (Filename example: ALL_TVNB012_00_UF_XX91_AA.ecc)
Upgrade the firmware and initialize the setting values along with the factory default such as White Balance, etc.
Before the upgrade, you will need to make a note of all the factory default so you will be able to set it back on the
TV after the initialization.
The Flash Upgrade will be done by it's unique file.
The User Upgrade/Firmware Upgrade (Factory Upgrade) file cannot be used for this upgrade.

Update procedure
1. Turn the power off. The appearance shown in *1 is described as follows.
2. Insert the USB storage device to the USB port as Appearance State
shown below.
Downloading the firmware from
Downloading...
the USB storage device.
Rear Cabinet
Rear Cabinet Writing the downloaded firmware
Writing...
in flash memory.
USB port
USB port Checking... Checking the new firmware.

5. When the firmware update is completed, the


USB storage following will appear in the screen.
USB storage
device
device
Software Upgrade

The software upgrade is completed.


3. Turn the power on. Remove USB storage device, turn TV off then on again.

4. The update will start and the following will appear


in the screen.
"*" differs depending on the models. Remove the USB storage device from the USB
Software Upgrade port.
Turn the power off and turn the power on again.
Software upgrade in progress. Please wait.
Service mode initial screen with a word
Do not remove the USB storage device or
“INITIALIZED” will appear in the screen. The color
turn the TV off while upgrade is in progress.
of the word “INITIALIZED” will change from red to
Current Version: *******-***-*-***-**** green when initialization is completed.
New Version: *******-***-*-***-****
*1 Downloading...
0%

Note: If the above screen isn’t displayed, repeat from


step 1.

7-2 PL12.2_A FW
[TYPE B]
Equipment Required (Files included in the USB storage device are
displayed.)
1. USB storage device "*" differs depending on the models.
2. Remote Control Unit
Select an upgrade file *****_******.upg
Firmware Update Procedure *****_******.upg
1. Turn the power off and unplug the AC Cord. *****_******.upg
2. Insert the USB storage device to the USB port as
shown below.

Rear Cabinet
Rear Cabinet
Cancel
USB port
1 23
USB port Note:
To cancel the update mode, select “Cancel” and
press the [OK] button.
USB storage
device
USB storage
10. Select the file and press [OK] button.
device
11. The update will start and the following will appear
in the screen.
"*" differs depending on the models.
Current Version: ***-****-***-*
New Version: ***-****-***-*

Are you sure you want to update?

3. Plug the AC Cord and turn the power on.


4. After few seconds, the menu mode will appear in No Yes
the screen.
Note:
After 30 seconds without an operation, the menu Note:
mode will disappear automatically. If the above screen isn’t displayed, repeat from
To display the menu mode again, press the step 1.
[MENU] button on the remote control unit. 12. Select “Yes” and press the [OK] button to update.
5. Select “Setup” and press the [OK] button to display Note:
the setup menu.
Do not remove the USB storage device or turn the
6. Select “Software”. TV off while update is in progress.
7. Select “Software update”. 13. When the firmware update is completed, the
8. Select “USB”. following will appear in the screen.
9. Press the [OK] button on the remote control unit to
enter the update mode.
Update file selection screen appears as follows.
Update your TV with new software: Done

Software update is successful.


Please remove the USB storage device
and restart the TV set.

Remove the USB storage device from the USB


port.
Turn the power off and turn the power on again.

7-3 PL12.2_B (A27F5UH)_FW


TROUBLESHOOTING
[Power Supply Section]
FLOW CHART NO.1
The power cannot be turned on.

No
Is the fuse (F601) normal? See FLOW CHART No.2 <The fuse blows out.>
Yes

Is normal state restored when once unplugged No


power cord is plugged again after several seconds? Check if there is any leak or short-circuiting on the
Yes primary circuit component, and service it if defective.
No (D601, D602, D603, D604, Q601, Q602, T601)
Is the P-ON+21V line voltage normal?
Yes

Check each rectifying circuit of the secondary


circuit and service it if defective.

FLOW CHART NO.2


The fuse blows out.

Check the presence that the primary component Check the presence that the rectifying diode or circuit
is leaking or shorted and service it if defective. is shorted in each rectifying circuit of secondary side,
and service it if defective.

After servicing, replace the fuse.

FLOW CHART NO.3


When the output voltage fluctuates.

Does the photocoupler circuit on the secondary side No Check IC601, D660, D661B, Q652, Q653 and their
operate normally? periphery circuit, and service it if defective.
Yes

Check IC601, D605, D607, D608, D609, D610, Q601,


Q602 and their periphery circuit, and service it if
defective.

FLOW CHART NO.4


When buzz sound can be heard in the vicinity of power circuit.

Check if there is any short-circuit on the rectifying diode and the circuit in each rectifying circuit of the secondary side,
and service it if defective. (D650, D651, D653, Q656)

8-1 PL12.2ATR
FLOW CHART NO.5
P-ON+21V is not output.

Is approximately +21V voltage supplied to the cathode No Check D650, D651, C651, C652, C653 and their
of D650(D651)? periphery circuit, and service it if defective.
Yes
Check for short-circuiting or leak on the load circuit,
and service it if defective.

FLOW CHART NO.6


AMP+24V is not output.

No
Is approximately +24V voltage supplied to the cathode Check D653, D654, C654, C655 and their periphery
of D653? circuit, and service it if defective.
Yes

Check for short-circuiting or leak on the load circuit,


and service it if defective.

FLOW CHART NO.7


AL+3.3V is not output.

No
Is approximately +21V voltage supplied to the Check D650, D651, C651, C652, C653 and their
collector of Q656? periphery circuit, and service it if defective.
Yes
No
Is approximately +4V voltage supplied to the base of Check D662 and their periphery circuit, and service it
Q656? if defective.
Yes

Replace Q656.

8-2 PL12.2ATR
[Video Signal Section]
FLOW CHART NO.1
The key operation is not functioning.

No
When touching each buttons do the voltage of Pin(6) Is approximately +3.3V voltage supplied to Pin(1)
of CN4001 decrease? of CN4001?
Yes Yes No

Replace Digital Main CBA Unit. Replace IC4001 Check AL+3.3V line and
or Function CBA. service it if defective.

FLOW CHART NO.2


No operation is possible from the remote control unit. (Operation is possible from the unit.)

No
Is approximately +3.3V voltage supplied to Pin(3) Check AL+3.3V line and service it if defective.
terminal of the remote control receiver (RS4051)?
Yes
No
Is the "L" pulse sent out Pin(1) terminal of remote Replace the remote control receiver (RS4051)
control receiver (RS4051) when the infrared remote or the remote control unit.
control is activated?
Yes
Check the line between Pin(1) of remote control
No
Is the "L" pulse supplied to Pin(5) of CN4001? receiver (RS4051) and Pin(5) of CN4001, and
Yes service it if defective.

Replace Digital Main CBA Unit.

FLOW CHART NO.3


Picture does not appear normally.

No
Is approximately +21V voltage supplied to See FLOW CHART NO.5 <P-ON+21V is not output.
Pin(16, 17, 22, 23) of CN631? [Power Supply Section]>
Yes
No
Is approximately +24V voltage supplied to Pin(13, 14) See FLOW CHART NO.6 <AMP+24V is not output.
of CN631? [Power Supply Section]>
Yes
No
Is approximately +3.3V voltage supplied to Pin(11) of See FLOW CHART NO.7 <AL+3.3V is not output.
CN631? [Power Supply Section]>
Yes

Digital Main CBA Unit or LCD Panel Assembly may


be defective.
Check and replace these parts.

8-3 PL12.2ATR
[Audio Signal Section]
FLOW CHART NO.1
Audio is not outputted normally.

No
Is approximately +21V voltage supplied to See FLOW CHART NO.5 <P-ON+21V is not output.
Pin(16, 17, 22, 23) of CN631? [Power Supply Section]>
Yes
No
Is approximately +24V voltage supplied to Pin(13, 14) See FLOW CHART NO.6 <AMP+24V is not output.
of CN631? [Power Supply Section]>
Yes
No
Is approximately +3.3V voltage supplied to Pin(11) of See FLOW CHART NO.7 <AL+3.3V is not output.
CN631? [Power Supply Section]>
Yes
No
Are the audio signals outputted to Pin(1, 4) of CN3801? Replace Digital Main CBA Unit.
Yes

SP3801, SP3802 or CL3801 may be defective.


Check and replace these parts.

8-4 PL12.2ATR
IC3005
(MAIN MICRO CONTROLLER)
[TYPE A]

KEY-IN1 A15
REMOTE C14
LED1 D14 LED DRIVE
Q3501, Q3502

RS4051 P-ON+5V
REMOTE
SENSOR
D4051
POWER
CN3101 CN4001
IC4001
5 REMOTE 5 (TOUCH SENSOR)
6 LED1 4
2 SCL 8 4 SCL POWER 16 POWER
1 SDA 9 5 SDA SOURCE 17 SOURCE
TO AUDIO-MUTE 4 KEY-IN1 6 1 POWER
VIDEO/AUDIO C1 AUDIO-MUTE MENU 18 MENU
BLOCK DIAGRAM
2 SOURCE CH UP 19 CH UP
CH DOWN 21 CH DOWN
3 MENU
TU3901 (TUNER UNIT) VOL UP 22 VOL UP
6 CH UP VOL DOWN 23 VOL DOWN
1. System Control Block Diagram

SCL R12 4 SCL


11 CH DOWN
SDA T12 3 SDA

9-1
12 VOL UP

13 VOL DOWN
AL+3.3V

IC3006 (MEMORY) FUNCTION CBA


SCK 6 T11 SCK
P-ON-H2 B16 Q3006
SI 5 P11 SIN
SO 2 R11 SOUT Q3005
BLOCK DIAGRAMS

CS 1 P12 CS

CN3701 CN631
P-ON-H2 TO
7 P-ON-H2 7 POWER SUPPLY
RESET
RESET J15 RESET 8 RESET 8 BLOCK DIAGRAM
IC3009

CN3701 CN631
PROTECT3
X3001 PROTECT3 B13 4 PROTECT3 4 TO
BACKLIGHT-SW
25MHz H15 XIN25 BACKLIGHT-SW E2 2 BACKLIGHT-SW 2 LED BACKLIGHT DRIVE
OSC BACKLIGHT-ADJ BLOCK DIAGRAM
H16 XOUT25 BACKLIGHT-ADJ F3 3 BACKLIGHT-ADJ 3

BACKLIGHT-SW TO
VIDEO/AUDIO
BLOCK DIAGRAM

DIGITAL MAIN CBA UNIT POWER SUPPLY CBA

PL12.2ABLS
VIDEO SIGNAL AUDIO SIGNAL

VGA-R-IN
1
VGA-G-IN
2 VGA-B-IN
VGA-HSYNC
JK3001 3
VGA-VSYNC
PC-RGB IC3013
13 BUFFER GATE VGA-SCL
IN
IC3014 VGA-SDA
14 BUFFER GATE
Q3301 TU3901 (TUNER UNIT)
15 BUFFER
Q3302 DIF-OUT1
12 BUFFER DIF-OUT1 6
DIF-OUT2
DIF-OUT2 7
IF-AGC
IF-AGC 5

JK3702
COM-VIDEO-Y/VIDEO-IN
COMPONENT COM-VIDEO-Pb-IN
-Y/VIDEO-IN COM-VIDEO-Pr-IN
COMP-DET
COMPONENT
-Pb-IN

COMPONENT TO DIGITAL
-Pr-IN SIGNAL PROCESS
2. Video/Audio Block Diagram

BLOCK DIAGRAM

JK3701
AUDIO(L)-IN

9-2
AUDIO(L)-IN AUDIO(R)-IN

AUDIO(R)-IN
Q3701
SPDIF
DIGITAL BUFFER
AUDIO-OUT
(COAXIAL)

IC3801 (AUDIO AMP)

AMP(R)-OUT
39,40 DRIVE PWM 32

JK3703
HEADPHONE
JACK AMP(L)-OUT
11,12 DRIVE PWM 19

Q3801 AUDIO-MUTE
34
CONTROL LOGIC Q3803
17 P-ON+5V TO SYSTEM CONTROL
CN3801 BLOCK DIAGRAM
SP3801 SP(L) 1
SPEAKER Q3802 BACKLIGHT-SW
GND 2
L-CH
SP(R) 4
GND 3

SP3802
SPEAKER
R-CH DIGITAL MAIN CBA UNIT

PL12.2ABLVA
VIDEO SIGNAL AUDIO SIGNAL
LCD PANEL
IC3005 (DIGITAL SIGNAL PROCESS) ASSEMBLY
VGA-HSYNC
A14 HSYNC
VGA-VSYNC CN3006
B14 VSYNC
VGA-R-IN P14 23 LLV0(+)
C11 P13 22 LLV0(-)
VGA-G-IN
A9 N16 21 LLV1(+)
VGA-B-IN
C7 N15 20 LLV1(-)
COM-VIDEO-Y/VIDEO-IN SW A/D
C9 CONVERTER P16 19 LLV2(+)
COM-VIDEO-Pb-IN
D8 P15 18 LLV2(-)
COM-VIDEO-Pr-IN
B11 T16 13 LLV3(+)
C10 LVDS TX
T15 12 LLV3(-)
R14 11 LLV4(+)
TO DIF-OUT1
VIDEO/AUDIO A12 DEMODULATOR T14 10 LLV4(-)
DIF-OUT2
BLOCK DIAGRAM B12 /MPEG DECODER R13 9 LLV5(+)
IF-AGC T13 8 LLV5(-)
A16 IF-AGC
COMP-DET R16 16 LLVCLK(+)
N12 COMP-DET
R15 15 LLVCLK(-)
AUDIO(L)-IN TP L13 6 TP
A8
AUDIO(R)-IN POL M15 5 POL
B8
SPDIF CPV L16 4 CPV
N10 AUDIO I/F
AMP(L)-OUT OE L15 3 OE
B7
AMP(R)-OUT STV M14 1 STV
A7
OE2 L14 2 OE2

JK3004
HDMI-IN1 IC3018 (HDMI SW) AUDIO
DECODER
TMDS-D0(+)
7 42
TMDS-D0(-) DIGITAL
9 41 SIGNAL
TMDS-D1(+)
4 45 26 B4 PROCESS
TMDS-D1(-)
6 44 27 A4
TMDS-D2(+)

9-3
1 48 23 B3
TMDS-D2(-)
3 47 24 A3 HDMI
TMDS-CLOCK(+)
10 39 20 B2 I/F
TMDS-CLOCK(-)
12 38 21 A2
3. Digital Signal Process Block Diagram

HDMI-DATA
16 36 17 B1
HDMI-CLOCK
15 37 18 A1

JK3002 HDMI JK3003


HDMI-IN2 SW HDMI-IN3
TMDS-D0(+) TMDS-D0(+)
7 8 57 7 VIDEO
TMDS-D0(-) TMDS-D0(-)
9 7 56 9 DECODER
TMDS-D1(+) TMDS-D1(+)
4 11 60 4
TMDS-D1(-) TMDS-D1(-)
6 10 59 6 IC3002
TMDS-D2(+) TMDS-D2(+) (DDR2 SDRAM)
1 14 63 1
TMDS-D2(-) TMDS-D2(-)
3 13 62 3
TMDS-CLOCK(+) TMDS-CLOCK(+) N4,N7,N8,P3,P4, B1,B9,C2,C8,
10 5 54 10 D1,D3,D7,D9,
TMDS-CLOCK(-) TMDS-CLOCK(-) P6-P8,R3,R4,R6,
12 4 53 12 R8,T2-T5 F1,F9,G2,G8, DATA(0-15)
HDMI-DATA HDMI-DATA H1,H3,H7,H9
16 1 51 16
HDMI-CLOCK HDMI-CLOCK M2,M3,M7,M8,
15 2 52 15 H1,H2,J1,J2,J4,K1, N2,N3,N7,N8, ADDRESS(0-12)
K3,L1,L2,M1-M3,N1 P2,P3,P7,P8,R2
IC3011
(HDMI SERIAL EEPROM)

2 SCL1 SCL2 15
3 SDA1 SDA2 14
10 SCL3 SCL0 7 G14 HDMI-SCL
11 SDA3 SDA0 6 F14 HDMI-SDA

TO VGA-SCL
VIDEO/AUDIO VGA-SDA
BLOCK DIAGRAM DIGITAL MAIN CBA UNIT

PL12.2ABLD
LCD PANEL ASSEMBLY

P-ON+21V

Q1001
IC1001
(LED BACKLIGHT DRIVER)

10 OVP DRIVE 2

DRIVE 3
16
CN1001
14 CONTROL 4 VLED
BACKLIGHT-SW
TO 13 LOGIC 6 ILED1
BACKLIGHT-ADJ
SYSTEM CONTROL 1 7 ILED2
BLOCK DIAGRAM PROTECT3

9-4
DRIVE 5 2 ILED3
4. LED Backlight Drive Block Diagram

POWER SUPPLY CBA

PL12.2BLBD
CAUTION !
NOTE:
Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. CAUTION ! : For continued protection against risk of fire, The voltage for parts in hot circuit is measured using
If Main Fuse (F601) is blown , check to see that all components in the power supply replace only with same type 4A, 125V fuse. hot GND as a common terminal.
circuit are not defective before you connect the AC plug to the AC power supply. 4A 125V ATTENTION : Utiliser un fusible de rechange de même type de 4A, 125V.
Otherwise it may cause some components in the power supply circuit to fail.

HOT CIRCUIT. BE CAREFUL.

CN631 CN3701
AC601
AC CORD F601 L601 L602 D601- D604 T601 13,14 AMP+24V 13,14 AMP+24V
CN601 4A/125V 11 AL+3.3V 11 AL+3.3V
2 LINE LINE BRIDGE 6 7 16,17 P-ON+21V 16,17 P-ON+21V
1 FILTER FILTER RECTIFIER
22,23 P-ON+21V 22,23
Q650
8 RESET

4A 125V 5 DIGITAL MAIN CBA UNIT


Q501
SWITCHING 9

4 10

2
11 P-ON+21V
5. Power Supply Block Diagram

1 12

9-5
RESET TO
Q601
P-ON-H2 SYSTEM CONTROL
SWITCHING BLOCKDIAGRAM
Q656
+3.3V REG.

IC601
ERROR
VOLTAGE DET

4 1
Q602
SWITCHING
3 2
CONTROL

Q652

Q653

HOT COLD
POWER SUPPLY CBA

PL12.2ABLP
IC3101
[TYPE B]

(MAIN MICRO CONTROLLER)


CN3705
WIRELESS USB0(+)
U26 USB0(+)
LAN USB0(-)
ADAPTOR U25 USB0(-)
KEY-IN1 AF2
CN3704 REMOTE Y23
USB1(+)
V25 USB1(+) LED1 W23 LED DRIVE
USB JACK USB1(-)
U24 USB1(-) Q3101

IC3902
(ETHERNET I/F)

14 AA3 RMII-RXD0 RS4051 P-ON+5V


CN3706 16 W5 RMII-RXD1 REMOTE
TD(+) SENSOR
1 17 W4 RMII-RXD2 D4051
TD(-)
ETHERNET 2 ETHERNET 18 AB2 RMII-RXD3 POWER
JACK RD(+)
4 I/F CN3105 CN4001
RD(-) 23 Y3 RMII-TXD0 IC4001
5 5 REMOTE 5
24 V6 RMII-TXD1 (TOUCH SENSOR)
25 Y4 RMII-TXD2 6 LED1 4
26 Y2 RMII-TXD3 2 SCL 8 4 SCL POWER 16 POWER
1 SDA 9 5 SDA SOURCE 17 SOURCE
X3701 4 KEY-IN1 6 1 POWER
25MHz 42 XI MENU 18 MENU
OSC 43 XO RESET 29 AD1 HUB-RESET 2 SOURCE CH UP 19 CH UP
IC3103 (MEMORY)
CH DOWN 21 CH DOWN
1. System Control Block Diagram

3 MENU
STM-SCL AC5 6 SCL VOL UP 22 VOL UP
STM-SDA AE4 5 SDA 6 CH UP VOL DOWN 23 VOL DOWN

9-6
11 CH DOWN
VGA-SCL
Y20 VGA-SCL 12 VOL UP
VGA-SDA
AA20 VGA-SDA TU3001 (TUNER UNIT)
TO VIDEO/AUDIO AMP-MUTE
V23 AMP-MUTE 13 VOL DOWN
BLOCK DIAGRAM COMP-DET
P1 COMP-DET TU-SCL AE10 6 SCL
LCD-P-ON
V20 LCD-P-ON TU-SDA AD9 5 SDA
FUNCTION CBA

CN3601 CN631
P-ON-H2 TO
P-ON-H2 AE2 7 P-ON-H2 7 POWER SUPPLY
X3101 RESET
RESET AB6 RESET 8 RESET 8 BLOCK DIAGRAM
24.576MHz AF3 AXI
OSC IC3009
AE3 AXO

CN3601 CN631
PROTECT3
PROTECT3 AE1 4 PROTECT3 4 TO
BACKLIGHT-SW
BACKLIGHT-SW K25 2 BACKLIGHT-SW 2 LED BACKLIGHT DRIVE
BACKLIGHT-ADJ BLOCK DIAGRAM
BACKLIGHT-ADJ G6 3 BACKLIGHT-ADJ 3

DIGITAL MAIN CBA UNIT POWER SUPPLY CBA

PL12.2BBLS
VIDEO SIGNAL AUDIO SIGNAL

VGA-R-IN
1
VGA-G-IN
2 VGA-B-IN
VGA-HSYNC
JK3713 3
VGA-VSYNC
PC-RGB
13
IN
14
TU3001 (TUNER UNIT)
15
DIF-OUT1
12 DIF-OUT1 6
DIF-OUT2
DIF-OUT2 7
IF-AGC
IF-AGC 5

JK3701
COM-VIDEO-Y/VIDEO-IN
COMPONENT COM-VIDEO-Pb-IN
-Y/VIDEO-IN COM-VIDEO-Pr-IN

COMPONENT
-Pb-IN

COMPONENT TO DIGITAL
2. Video/Audio Block Diagram

-Pr-IN SIGNAL PROCESS


BLOCK DIAGRAM

9-7
JK3706
AUDIO(L)-IN
AUDIO(L)-IN AUDIO(R)-IN

AUDIO(R)-IN
Q3001
SPDIF
DIGITAL BUFFER
AUDIO-OUT
(COAXIAL)

IC3801 (AUDIO AMP)

AMP(R)-OUT
39,40 DRIVE PWM 32

JK3801
HEADPHONE
JACK AMP(L)-OUT
11,12 DRIVE PWM 19

Q3801 AUDIO-MUTE
34
CONTROL LOGIC Q3803 VGA-SCL
17 P-ON+5V VGA-SDA TO SYSTEM CONTROL
CN3801 BLOCK DIAGRAM
COMP-DET
SP3801 SP(L) 1
SPEAKER Q3802 LCD-P-ON
GND 2
L-CH
SP(R) 4
GND 3

SP3802
SPEAKER
R-CH DIGITAL MAIN CBA UNIT

PL12.2BBLVA
VIDEO SIGNAL AUDIO SIGNAL LCD PANEL
ASSEMBLY
IC3101 (DIGITAL SIGNAL PROCESS)
VGA-HSYNC
AB9 VGA-HSYNC
VGA-VSYNC
AA9 VGA-VSYNC
VGA-R-IN
Y18
VGA-G-IN
AA17
VGA-B-IN
Y17
COM-VIDEO-Y/CVBS-IN A/D
AA15 SW CONVERTER
COM-VIDEO-Pb-IN
AA14
COM-VIDEO-Pr-IN
AB14
AB17 CN3904
TO VIDEO/AUDIO L4 23 LVDS-OD0(-)
BLOCK DIAGRAM DIF-OUT1
AE6 DEMODULATOR L5 22 LVDS-OD0(+)
DIF-OUT2
AD6 /MPEG DECODER L3 21 LVDS-OD1(-)
IF-AGC
AD7 IF-AGC L2 20 LVDS-OD1(+)
AMP(L)-OUT K5 19 LVDS-OD2(-)
AC10 K4 18 LVDS-OD2(+)
AMP(R)-OUT
AB11 LVDS TX K3 16 LVDS-OCLK(-)
AUDIO(L)-IN
AD13 AUDIO I/F L1 15 LVDS-OCLK(+)
AUDIO(R)-IN
AE13 A2 6 TP
SPDIF
AD10 D4 5 POL
JK3717 Q3002 Q3004 Q3003
B3 4 CPV
BUFFER MUTE BUFFER
ARC AB25 ARC-MUTE B2 3 OE
14
DATA0(+) D5 2 OE2
7 AD15
DATA0(-) C3 1 STV
9 AE15 AUDIO
DATA1(+) DECODER
4 AE16 DIGITAL
DATA1(-)
6 AF16 SIGNAL
DATA2(+) PROCESS
1 AE17
HDMI-IN1 DATA2(-)
3 AF17
CLOCK(+)
10 AE14
CLOCK(-)

9-8
12 AF14
HDMI-DATA
16 AA24
HDMI-CLOCK
15 AA22
3. Digital Signal Process Block Diagram

JK3715
DATA0(+)
7 AE23 HDMI
DATA0(-) I/F
9 AF23
DATA1(+)
4 AE24
DATA1(-) IC3401
6 AF24 (DDR3 SDRAM)
DATA2(+) HDMI SW
1 AE25
HDMI-IN2 DATA2(-) DATA(0-15)
3 AF25
CLOCK(+) ADDESS(0-13)
10 AE22
CLOCK(-)
12 AF22 IC3402
HDMI-DATA (DDR3 SDRAM)
16 AB23
HDMI-CLOCK
15 AB22 DATA(16-31)
ADDESS(0-13)
JK3716 VIDEO IC3102
DATA0(+) DECODER (NAND FLASH MEMORY)
7 AE19
DATA0(-)
9 AF19 DATA(0-7)
DATA1(+)
4 AE20
DATA1(-)
6 AF20
DATA2(+)
1 AD21
HDMI-IN3 DATA2(-)
3 AE21
CLOCK(+)
10 AD18
CLOCK(-)
12 AE18
HDMI-DATA
16 Y21
HDMI-CLOCK
15 W21
DIGITAL MAIN CBA UNIT

PL12.2BBLD
LCD PANEL ASSEMBLY

P-ON+21V

Q1001
IC1001
(LED BACKLIGHT DRIVER)

10 OVP DRIVE 2

DRIVE 3
16
CN1001
14 CONTROL 4 VLED
BACKLIGHT-SW
TO 13 LOGIC 6 ILED1
BACKLIGHT-ADJ
SYSTEM CONTROL 1 7 ILED2
BLOCK DIAGRAM PROTECT3

9-9
DRIVE 5 2 ILED3
4. LED Backlight Drive Block Diagram

POWER SUPPLY CBA

PL12.2BLBD
CAUTION !
NOTE:
Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. CAUTION ! : For continued protection against risk of fire, The voltage for parts in hot circuit is measured using
If Main Fuse (F601) is blown , check to see that all components in the power supply replace only with same type 4A, 125V fuse. hot GND as a common terminal.
circuit are not defective before you connect the AC plug to the AC power supply. 4A 125V ATTENTION : Utiliser un fusible de rechange de même type de 4A, 125V.
Otherwise it may cause some components in the power supply circuit to fail.

HOT CIRCUIT. BE CAREFUL.

CN631 CN3601
AC601
AC CORD F601 L601 L602 D601- D604 T601 13,14 AMP+24V 13,14 AMP+24V
CN601 4A/125V 11 AL+3.3V 11 AL+3.3V
2 LINE LINE BRIDGE 6 7 16,17 P-ON+21V 16,17 P-ON+21V
1 FILTER FILTER RECTIFIER
22,23 P-ON+21V 22,23
Q650
8 RESET

4A 125V 5 DIGITAL MAIN CBA UNIT


Q501
SWITCHING 9

4 10

2
11 P-ON+21V
5. Power Supply Block Diagram

1 12

9-10
RESET TO
Q601
P-ON-H2 SYSTEM CONTROL
SWITCHING BLOCKDIAGRAM
Q656
+3.3V REG.

IC601
ERROR
VOLTAGE DET

4 1
Q602
SWITCHING
3 2
CONTROL

Q652

Q653

HOT COLD
POWER SUPPLY CBA

PL12.2BBLP
SCHEMATIC DIAGRAMS / CBA AND TEST POINTS
Standard Notes
WARNING
Many electrical and mechanical parts in this chassis
have special characteristics. These characteristics
often pass unnoticed and the protection afforded by
them cannot necessarily be obtained by using
replacement components rated for higher voltage,
wattage, etc. Replacement parts that have these
special safety characteristics are identified in this
manual and its supplements; electrical components
having such features are identified by the mark “#” in
the schematic diagram and the parts list. Before
replacing any of these components, read the parts list
in this manual carefully. The use of substitute
replacement parts that do not have the same safety
characteristics as specified in the parts list may create
shock, fire, or other hazards.

Notes:
1. Do not use the part number shown on these
drawings for ordering. The correct part number is
shown in the parts list, and may be slightly
different or amended since these drawings were
prepared.
2. All resistance values are indicated in ohms
(K = 103, M = 106).
3. Resistor wattages are 1/4W or 1/6W unless
otherwise specified.
4. All capacitance values are indicated in µF
(P = 10-6 µF).
5. All voltages are DC voltages unless otherwise
specified.
6. This schematic diagrams are masterized version
that should cover the entire PL12.2 chassis models.
Thus some parts in detail illustrated on this
schematic diagrams may vary depend on the
model within the PL12.2 chassis.
Please refer to the parts lists for each models.
7. The Circuit Board layout illustrated on this service
manual is the latest version for this chassis at the
moment of making this service manual.
Depend on the mass production date of each
model, the actual layout of each Board may differ
slightly from this version.

10-1 PL12.2SC
LIST OF CAUTION, NOTES, AND SYMBOLS USED IN THE SCHEMATIC DIAGRAMS ON
THE FOLLOWING PAGES:
1. CAUTION:
CAUTION: FOR CONTINUED PROTECTION AGAINST RISK OF FIRE, REPLACE ONLY WITH SAME
TYPE_A,_V FUSE.
ATTENTION: UTILISER UN FUSIBLE DE RECHANGE DE MÊME TYPE DE_A,_V.

2. CAUTION:
Fixed Voltage (or Auto voltage selectable) power supply circuit is used in this unit.
If Main Fuse (F601) is blown, first check to see that all components in the power supply circuit are not
defective before you connect the AC plug to the AC power supply. Otherwise it may cause some components
in the power supply circuit to fail.

3. Note:
1. Do not use the part number shown on the drawings for ordering. The correct part number is shown in the
parts list, and may be slightly different or amended since the drawings were prepared.
2. To maintain original function and reliability of repaired units, use only original replacement parts which are
listed with their part numbers in the parts list section of the service manual.

4. Voltage indications on the schematics are as shown below:


Plug the TV power cord into a standard AC outlet.:

1 2 3
(Unit: Volt) 5.0 5.0 Power on mode

Voltage Indicates that the voltage


is not consistent here.

5. How to read converged lines


1-D3
Distinction Area 3 1-B1
Line Number AREA D3
(1 to 3 digits)
2 AREA B1
Examples:
1. "1-D3" means that line number "1" goes to the line number
"1" of the area "D3". 1 1-D3
2. "1-B1" means that line number "1" goes to the line number
"1" of the area "B1". A B C D

6. Test Point Information


: Indicates a test point with a jumper wire across a hole in the PCB.
: Used to indicate a test point with a component lead on foil side.
: Used to indicate a test point with no test pin.
: Used to indicate a test point with a test pin.

The reference number of parts on Schematic Diagrams/CBA can be retrieved by


application search function.

10-2 PL12.2SC
Power Supply Schematic Diagram

CAUTION !
Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. CAUTION ! : For continued protection against risk of fire, NOTE:
If Main Fuse (F601) is blown , check to see that all components in the power supply replace only with same type 4A, 125V fuse. The voltage for parts in hot circuit is measured using
circuit are not defective before you connect the AC plug to the AC power supply. 4A 125V hot GND as a common terminal.
ATTENTION : Utiliser un fusible de rechange de même type de 4A, 125V.
Otherwise it may cause some components in the power supply circuit to fail.

BC1002 C1001 C1002 C1003 C1004 L1001


WIRE 22uH D102A
HOT CIRCUIT. BE CAREFUL. POWER SUPPLY CBA 330/25V OPEN 1 1 D1001
SK210TD Q1001
OPEN
AP18T10AGH-HF D1002
AC601

4 AC CORD CN601
1
2
F601 R601
1.2M/1/2W
C1010
47/100V
C1009 C1008 R1004
1/100V 1/100V 560K
R1005
200K
D1004
OPEN
C1007
220P/1KV
18.0 D (SWITCHING)

0.1 S
G 2.3
R1002
200
R1001
10

4A/125V C603
1000P/250V
SA601 C1006 C1005
SURGE C1014 D1005B D1005 R1006 R1003 1000P OPEN
ABSORBER 1000P OPEN OPEN 27K 0.18/1W

4A 125V C604
0.22/275V C1015 R1011 R1010 C1011 C1012 C1013
OPEN 100K 10K 47/100V 1/100V OPEN
IC1001
L601 HA7209PC
LINE FILTER LED BACKLIGHT
DRIVER
GT601 JS601 JS602 SA602 R403 D402B D402
OPEN OPEN OPEN OPEN
3.0 1 OPEN 24BSB-T26 OPEN
24 0
C614
0.22/275V D601 D604 0.5 2
1N5406BH 1N5406BH DRIVE NU 23
R1012 C1016 R401
L602 R602 0.5 3 100 1
LINE 1.2/5W DRIVE COMP 22 1.7 8.2K
FILTER 0.5 4 C1018
SA603 GT602 DRIVE MCP 21 0 OPEN D401
OPEN OPEN D602 D603 R1019
1N5406BH 1N5406BH 0.5 5 OPEN
D653 DRIVE SEL 20 0 D401A
C601 OPEN SB3200BR R1015 R1014 OPEN

3 C617 OPEN C654


470/35V
C655 D654
470/35V 1ZB30BB D654A
OPEN
R650
5.6K
R650A R678
OPEN 5.6K
R678A
OPEN
0 6 GND
0 7 DRIVE
VIN 19 19.0
GND 18 0 R1018
0
C1017
0.1
240 240
C1021
OPEN
R402
3K

0 8 DRIVE DRIVE LDO 17 5.0


T601
POWER TRANS 0 9
C658 DRIVE 16 2.7
OPEN C1019
6 7 1.5 10 OVP
C605 15 0 4.7
C615 330 R614 3.3
OPEN /200V 330K R501 Q501 R651 D656 D657 R652 1.2 11 ISET
47/2W 2SK3498 1 RS1BJTB MM5Z5V6B 56K -2.5 Q650 CONTROL 14 0.1
R603 (SWITCHING) 5 8 KTC3875S-Y-RTK/P LOGIC R1016
(RESET) R1008 1.0 12 RT 10K
330K
164.0 3.6 C656 D657B 0 360 13 3.0
1/50V OPEN
R604 3.6 BC601 R1009 R1007 C1022 C1020 R1017
330K 9 8.2K 100K OPEN OPEN 100K TO LCD PANEL
BEAD CN1001 ASSEMBLY
4 R1501 OPEN 0.5 1
C501 ILED4
0.1 10 C650 R1503 0 0.5 2
2200P/1KV ILED3
D502 R502 R1502 R1504 3 NU
UDZSNPTE-1730B 1.5M R606A R607A D651 0 OPEN 39.0 4
Q601 OPEN OPEN 2 11 SB3150BH R653 VLED
TK8A50D D501 47K
166.9 D 5 NU
(SWITCHING) R605 UDZSNPTE-1733B C608 R606 R607 D650 R1020 0 0.5 6
G 330K 0.039 270 270 SB3150BH ILED1
1 12 R1021 0 0.5 7
9.6 ILED2
0 S Q602 C651 C652 C653 D652 D652A

2 C607
1200P
3.6
2SC2120-Y
SWITCHING
CONTROL
0.4
R608
1.5K
R608A
OPEN
D605B
OPEN
D605
MM5Z4V3B
C602
1000P/250V
470/25V 470/25V 470/25V OPEN OPEN
D405
OPEN
D405A C632 OPEN
TO DIGITAL MAIN
OPEN CBA UNIT CN3601
0 R610 C616 CN631 or CN3701
C606 OPEN 1000P/250V C631 OPEN 0 1
820P VCOM-PWM(NU)
/2KV D610A D610 C630 OPEN 3.3 2
D607A D607 OPEN Q655 D406 BACKLIGHT-SW
OPEN 1ZB27BB OPEN OPEN 3.3 3
D658A D658 BACKLIGHT-ADJ
R613A R613 IC601 R655A R654A OPEN OPEN 3.3 4
OPEN 220 TLP781F(D4-FUNBLLF) OPEN OPEN R676 D406A PROTECT3
OPEN OPEN 0 5
ERROR PROTECT1
D609A VOLTAGE DET R655 R654 R673 C633 0 6 P-ON-H1(NU)
OPEN 14.3 21.0 180 180 5.6 21.0 3.3 OPEN
4 1 3.3 7 P-ON-H2
C610 C659 Q656
1000P R657 OPEN 2SC2120-Y R662 C661 3.3 8 RESET
D609 0.5 19.9 3.9K C664 3.9 (+3.3V REG.) 1.5K OPEN
3 2 OPEN C635 C636 0 9 OE2(NU)
R657A R659 OPEN OPEN 0 10
D608A D608 R611 C609 R612 R612A OPEN 22K R680 GND
OPEN 1ZB36BB 0.36 0.082 2.2K OPEN 10K JS632 3.3 11
/2W R660 AL+3.3V
C660 R658 2.7K R665 0 12
0.1 2.7K 10K R675 R670A R671A R672A C665 R682 GND
OPEN OPEN OPEN OPEN 0.1 0 24.7 13 AMP+24V
D661 D661B 24.7 14
OPEN 5V6BSB-T26 JS631 C663 C637 C638 AMP+24V
D660 R661 R666 R670 R671 R672 OPEN 100/10V OPEN OPEN 0 15
SL431A-AT 3.3K OPEN Q654 180 180 180 GND
OPEN 21.0 16
BC602 R677 P-ON+21V

1 BEAD
BC603
BEAD
15.4

0
Q652
KTC3875S-Y-RTK/P
(SWITCHING)
0
R664
10K
R667
OPEN
C662
OPEN D662
SL431A-AT R681
10K
10K
D663
OPEN
C639
OPEN
21.0 17
0 18
0 19
P-ON+21V
GND
GND
R663 0 R669 D663A 0 20 GND
BC604 47K Q653 0.3 10K OPEN
OPEN KTC3875S-Y-RTK/P 0 21 GND
(SWITCHING) 0 R668 21.0 22
22K P-ON+21V
21.0 23
HOT COLD P-ON+21V

UNLESS OTHERWISE SPECIFIED:


DIODES ARE HSS4148TE-E.

A B C D E F G
10-3 PL12.2SCP
Function Schematic Diagram

R4052 R4063 C4054 TO DIGITAL MAIN


6.8K OPEN 0.1 CBA UNIT CN3101
R4061 CN4001 or CN3105
OPEN 3.3 1
R4062 AL+3.3V
0 5.0 2 P-ON+5V
0 3 LIGHT
RS4051
GP1USC32XP 3.5 4

3 (REMOTE SENSOR) D4051


SML813WBC8W1
R4055
OPEN
R4059
OPEN 3.3 5
3.3 6
LED1
REMOTE

VOUT
VCC POWER IC4051 KEY-IN1
GND OPEN 0 7 GND
3 2 1 1 OUT NU 6 3.3 8 SCL
C4058 R4057 2 GND NU 5 3.3 9 SDA
R4051 D4053 OPEN OPEN
56 OPEN
R4054 3 VCC NU 4
1K R4053 D4052 C4057 R4058 R4056
2.2K OPEN OPEN OPEN OPEN
C4051 C4056 C4052 C4055
10 10 1000P OPEN
C4053
0.1

CN4003 (NO CONNECTION)


1 AL+3.3V
D4001 C4003 TP4001 R4001 2 ISSP-SDATA
MM5Z5V6B OPEN 560
POWER 3 ISSP-SCLK
TP4003 R4003 4 GND
560
SOURCE
TP4005 R4005
560
MENU 0 0 0 0 0 3.3

2 18 17

SOURCE
16 15 14 13 R4008
18K

POWER
MENU

GND

GND
TP4007 R4007
560 0 19
CH UP VOL DOWN 12 3.3
R4009
3.3 20 VDD CH UP VOL UP
CH DOWN 11 3.3
8.2K
TP4006 R4006 R4018
C4001 560 0 21 CH DOWN OPEN
1 CH DOWN NU 10 0
TP4004 R4004
560 0 22 VOL UP R4017
VOL UP GND 9 0 OPEN
TP4002 R4002
560 0 23 VOL DOWN
VOL DOWN GND 8 0 R4010
4.7K R4016
1.0 24 NU OPEN
NU 7 0
SOURCE
POWER

CH UP
MENU

C4002
SCL

SDA

2200P R4015
OPEN
1 2 3 4 5 6
IC4001 3.3 3.3 3.3 3.3 3.3 3.3
CY8C20336A
-24LQXIT R4011
(TOUCH SENSOR) 2.7K
R4012
2.2K
R4014 R4013
2.2K 100

1 R4021
10
R4022
10

C4007 D4003 C4008 D4004 D4002 C4006


OPEN MM5Z5V6B OPEN MM5Z5V6B OPEN OPEN
FUNCTION CBA

A B C D
10-4 PL12.2SCF
Digital Main 1 Schematic Diagram [TYPE A]
1 NOTE:
The order of pins shown in this diagram is different from that of actual IC3005.
IC3005 is divided into six and shown as IC3005 (1/6) ~ IC3005 (6/6) in this Digital Main Schematic Diagram Section.

CONTINUE
D3008
OPEN
R3081
0 DIGITAL MAIN CBA UNIT
DIGITAL 4
PROTECT3 CONTINUE
VCOM-PWM R3085 DIGITAL 4
C3166 C3167 R3171 OPEN
OE2 OPEN OPEN OPEN R3045 C3110 C3045 C3047 C3052 P-ON+5V
18K OPEN OPEN OPEN OPEN C3061 Q3207 P-ON+21V
R3129 OPEN OPEN
(NO CONNECTION) CN3013 OPEN P-ON+3.3V
GND 51 1 8
C3098 C3100 C3093 C3089 C3078 R3038 R3037 D3004 R3078 R3245 C3514 C3513

4 LCD+21V 50
LCD+21V 49
LCD+21V 48
R3174 OPEN
R3173 OPEN
R3170 OPEN
R3044
11K
R3047
3.9K R3046
12K
C3058
0.1
C3057
47/25V
R3074
OPEN
R3073
OPEN
2
3
4
7
6
5
OPEN OPEN OPEN OPEN 47/25V OPEN OPEN OPEN OPEN OPEN OPEN OPEN CN3006
30
29
TO LCD PANEL
ASSEMBLY
LCD+21V
LCD+21V
NU 47 R3090 28 GND
R3169 OPEN Q3007 OPEN Q3206
NU 46 R3168 2SC4081UBTLQ OPEN 27 VCOM-PWM
OPEN R3048 C3000 C3077 R3075 R3039
VCOM 45 1K OPEN (DRIVE) OPEN OPEN OPEN 26 PWR-CTRL
R3167 OPEN
P-ON+3.3V 44 R3130 25 P-ON+3.3V
R3166 OPEN OPEN C3512
P-ON+3.3V 43 R3035 OPEN 24 GND
R3165 OPEN 0
NU 42 23 LLV0(+)
GND 41 R3524 22 LLV0(-)
R3121 OPEN 10K
CPV 40 21 LLV1(+)
R3122 OPEN R3028
OE 39 0 20 LLV1(-)
R3123 OPEN
OE2 38 19 LLV2(+)
R3124 OPEN
TP 37 18 LLV2(-)
R3125 OPEN
LO-2N 36 17 GND
R3126 OPEN
POL 35 16 LLVCLK(+)
GND 34 15 LLVCLK(-)
R3127 OPEN
STV 33 14 GND
R3128 OPEN
LO-CP 32 13 LLV3(+)
GND 31 12 LLV3(-)

3 LO-3N 30
LO-3P 29
LLVO(+) 28
R3163 OPEN
R3164 OPEN
11
10
9
LLV4(+)
LLV4(-)
LLV5(+)
LLVO(-) 27 8 LLV5(-)
GND 26 7 GND
GND 25 6 TP
LLV1(+) 24 5 POL
LLV1(-) 23 4 CPV
LLV2(+) 22 3 OE
LLV2(-) 21 2 OE2
LLVCLK(+) 20 1 STV
LLVCLK(-) 19
GND 18 CN3001 (NO CONNECTION)
31 LCD+21V

OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
LLV3(+) 17
*1 30 LCD+21V
LLV3(-) 16 IC3005(1/6)
R8A05011BG-U0 29 LCD+21V

C3355
C3356
C3349
C3350
C3351
C3352
C3353
C3354
C3357
C3358
C3359
C3360
C3361
C3362
GND 15
DIGITAL SIGNAL PROCESS 28 GND
LLV4(+) 14 /MAIN MICRO CONTROLLER
LLV4(-) 13 27 VCOM-PWM
R3161 OPEN 26 PWR-CTRL
LLV5(+) 12
R3162 OPEN R16 25 P-ON+3.3V
LLV5(-) 11

2 GND 10
GND 9
GND 8 R3172
OPEN
R15
P14
P13
N16
24
23
22
21
GND
LLV0(+)
LLV0(-)
LLV1(+)
GND 7
GND 6 N15 20 LLV1(-)
LVDS P16 19 LLV2(+)
NU 5 TX
LCD+12V 4 P15 18 LLV2(-)
LCD+12V 3 T16 17 GND
LCD+12V 2 T15 16 LLVCLK(+)
LCD+12V 1 R14 15 LLVCLK(-)
C3170 C3171 T14 14 GND
OPEN OPEN R13 13 LLV3(+)
T13 12 LLV3(-)
11 LLV4(+)
LO-2N M16 10 LLV4(-)
LO-CP M13 9 LLV5(+)
TO DIGITAL LO-3N N14 8 LLV5(-)
MAIN 2
IC3005(2/6) LO-3P N13 R3152 7 GND
R3512 22 OPEN
TP L13 6 TP
R3513 22
POL M15 5 POL
R3518 22

1 CPV L16
OE L15
OE2 L14
STV M14
R3519
R3521
R3520
22
22
22
4
3
2
1
CPV
OE
OE2
STV
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN

OPEN
100P
OPEN
OPEN
OPEN
OPEN
100K

100K
100K
100K
100K
100K
NU K15
R3088
4.3K
CONTINUE
R3041

R3117
R3118
R3119
R3120
R3132
C3368
C3365
C3364
C3363
C3369
C3367
C3372
C3371
C3370
C3366

C3169
C3161
C3162
C3163
C3164
C3165

DIGITAL 3
CELL-PWR-CTRL

A B C D E F
10-5 PL12.2SCAD1
Digital Main 2 Schematic Diagram [TYPE A]
1 NOTE:
The order of pins shown in this diagram is different from that of actual IC3005.
IC3005 is divided into six and shown as IC3005 (1/6) ~ IC3005 (6/6) in this Digital Main Schematic Diagram Section.

TU3901 TUNER UNIT DIGITAL MAIN CBA UNIT


IC3013

DIF-OUT1
DIF-OUT2
74LVC1G126GW

IF-AGC
(BUFFER GATE)

+3.3V
GND
SDA
SCL
1 VCC 5
C3214 Q3301
1 2 3 4 5 6 7 2 0.1 2SK3018
(BUFFER) Q3302

4 C3903 0.1
C3902 0.1
3 GND 4 2SK3018
(BUFFER)
CONTINUE
DIGITAL 6
VGA-SDA
VGA-SCL
C3901 D3901 IC3014
OPEN MM5Z5V6B 74LVC1G126GW
(BUFFER GATE)
1 VCC 5 CONTINUE
L3913 DIGITAL 4
2.2uH
2 P-ON+3.3V
C3905 C3906 C3904 C3934 C3909 C3175 C3176 R3204 P-ON+5V
10 OPEN OPEN OPEN OPEN 33P 33P 2.7K 3 GND 4

D3903 D3902 C3908 R3203


MM5Z5V6B MM5Z5V6B OPEN 2.7K
R3298 R3296
C3910 C3907 R3903 D3904 10 10
10P OPEN OPEN MM5Z5V6B R3326 R3321
*1 4.7K 4.7K JK3001
IC3005(2/6) PC-RGB-IN
R8A05011BG-U0
DIGITAL SIGNAL PROCESS
/MAIN MICRO CONTROLLER
R3206 47 D3041 D3054 11 6 1
SCL R12 OPEN OPEN
R3207 47
SDA T12
TO DIGITAL B12 12 7 2

3 MAIN 5
IC3005(5/6) DEMODULATOR
/MPEG
DECODER
A12
C3173
33P

C3172
R3251
10

R3250
R3343
10
13 8 3

33P 10 R3358 D3050 14 9 4


10K OPEN
R3202 R3194 R3339
2.7K 1K 10
IF-AGC A16 15 10 5
R3347 D3045
R3205 C3178 C3177 10K OPEN
18K 0.1 1000P
HSYNC A14 D3049
R3301 OPEN
VSYNC B14 OPEN
C3194 0.1 R3285 47
A9
C3195 0.1 R3286 47 R3302 D3053
C7 OPEN OPEN
C3196 0.1 R3284 47
C11
C3291 C3292 C3293 R3356 R3377 R3364 R3303 D3055
SW 33P 33P 33P 75 75 75 OPEN OPEN
C3198 0.01
C10
C3199 0.1 R3327 10
C9
C3200 0.1 R3328 10 CONTINUE
D8 DIGITAL 3
C3201 0.1 R3329 10
B11 COMP-DET
A/D NU A10 C3289 C3288 C3287
CONVERTER 33P 33P 33P
NU C8

2 TO DIGITAL
MAIN 3
NU
NU
D9
B9
C3717 C3714 C3708 R3701
JK3702
COMPONENT
-Y/VIDEO-IN
IC3005(3/6) OPEN OPEN 0.1 C3701 75
DIGITAL R3711 OPEN
SIGNAL 7.5K
PROCESS COMPONENT
TO DIGITAL R3702 -Pb-IN
MAIN 3 C3702 75
IC3005(3/6) R3710 OPEN
100
COMPONENT
C3707 R3712 Q3701 C3703 R3703 -Pr-IN
1 10K 2SC4081UBTLQ OPEN 75
(BUFFER)
R3709 C3706 JK3701
C3197 C3335 C3716 220 1
OPEN 2.2 C3285 0.1 OPEN DIGITAL
TO DIGITAL TO DIGITAL NU B10 R3708 C3715 C3709 AUDIO-OUT
MAIN 6 MAIN 1 C3286 0.1 110 OPEN 100P (COAXIAL)
IC3005(6/6) IC3005(1/6) NU A11
C3336 1
NU D10 AUDIO(L)-IN
R3704
100K

AUDIO(R)-IN
R3705
100K CONTINUE
DIGITAL 5

1 SCL
SDA
AUDIO(L)-IN
AUDIO(R)-IN
CONTINUE
DIGITAL 5
SPDIF

G H I J K L
10-6 PL12.2SCAD2
Digital Main 3 Schematic Diagram [TYPE A]
1 NOTE:
The order of pins shown in this diagram is different from that of actual IC3005.
IC3005 is divided into six and shown as IC3005 (1/6) ~ IC3005 (6/6) in this Digital Main Schematic Diagram Section.

*1
C3009 IC3005(3/6)
OPEN R8A05011BG-U0 C3184
16P
DIGITAL SIGNAL PROCESS
R3064 C3050 /MAIN MICRO CONTROLLER X3001
100 OPEN 25MHz
M5 SD-VREF0
R3065 C3051 N3 GND R3226
100 0.1 XIN25 H15 R3223 OPEN C3183
1K 16P CN3012 (NO CONNECTION)

4 IC3002
SD-DQ15
SD-DQ14
R8
N8
SD-DQ15
SD-DQ14
XOUT25 H16

ASEBRKAK-N F15
1
2
3
AL+3.3V
GND
ASEBRKAK-N
K4T51163QI-HCF7 SD-DQ13 ASEMD0 F16 4 ASEMD0
(DDR2 SDRAM) P7 SD-DQ13 TRST-N E16 5 TRST-N
SD-DQ12 R6 SD-DQ12
C3029 0.1 TCK E15 6 TCK
*A VDD SD-DQ11 P6 SD-DQ11
C3030 OPEN VREF J2 TDI D16 7 TDI
C3010 SD-DQ10 N7 SD-DQ10
C3031 OPEN 0.1 TDO D15 8 TDO
SD-DQ9 T5 SD-DQ9
C3032 OPEN TMS E14 9 TMS
CKE K2 SD-DQ8 P8 SD-DQ8 TO DIGITAL
C3033 OPEN MAIN 2 R3522 10 CPU-RESET-N
E2 NU CK J8 SD-DQ7 P4 SD-DQ7 IC3005(2/6) 10K
C3034 0.1
A2 NU CK K8 SD-DQ6 T3 SD-DQ6 R3395 CN3010 (NO CONNECTION)
C3035 0.1 4.7K
R8 NU CS L8 SD-DQ5 R4 SD-DQ5 1 P-ON+5V
C3037 0.1 R3468 100
R7 NU RAS K7 SD-DQ4 T2 SD-DQ4 TXD0 G15 2 UART0-TX
C3038 OPEN R3469 100
R3 NU CAS L7 SD-DQ3 P3 SD-DQ3 RXD0 G16 3 UART0-RX
C3039 OPEN C3253
WE K3 SD-DQ2 T4 SD-DQ2 OPEN 4 GND
C3040 0.1 C3254 C3255 R3396
1-O3 B7 UDQS BA2/NU L1 SD-DQ1 R3 SD-DQ1 OPEN OPEN 4.7K
C3041 0.1
2-O3 A8 UDQS/NU BA1 L3 SD-DQ0 N4 SD-DQ0
C3140 0.1 CONTINUE
3-O3 B3 UDM BA0 L2 3-M3 T6 SD-UDM DIGITAL 2
SD-DQ15 B9 DQ15 A12 R2 6-M3 R5 SD-LDM COMP-DET
R3516 100
SD-DQ10 2-M3 BACKLIGHT-ADJ F3

3 SD-DQ12
SD-DQ11
SD-DQ13
B1
D9
D1
D3
DQ10
DQ12
DQ11
DQ13
A11
A10/AP
A9
A8
P7
M2
P3
P8
R3049
100
1-M3
5-M3
4-M3
T7
R7
N5
P5
SD-UDQSN
SD-UDQS
SD-LDQSN
SD-LDQS
VCOM-PWM F2
GND J14
R3517 100 CONTINUE
DIGITAL 5
CPU-RESET-N
BACKLIGHT-SW
SD-DQ14 D7 DQ14 A7 P2
SD-DQ9 CONTINUE
C2 DQ9 A6 N7 R3087 15 DIGITAL 4
SD-DQ8 L4 SD-WE R3511 22
C8 DQ8 A5 N3 R3082 6.8 CELL-PWR-CTRL D1 CELL-PWR-CTRL
4-O3 F7 LDQS A4 N8 R1 SD-CLKN GPY10 E13 GPY10
R3034 6.8
5-O3 E8 LDQS/NU A3 N2 R2 SD-CLK CPU-RESET-N
R3016 15 R3211 100
6-O3 F3 LDM A2 M7 L3 SD-CKE P-ON-H2 B16 P-ON-H2
R3084 15 R3233 OPEN
SD-DQ7 F9 DQ7 A1 M3 H2 SD-A8 P-ON-H1 G13 P-ON-H1
R3021 15 R3531 OPEN
SD-DQ6 F1 DQ6 A0 M8 H1 SD-A4 BACKLIGHT-ADJ
R3083 15 R3188 22
SD-DQ5 H9 DQ5 ODT K9 N2 SD-BA0 BACKLIGHT-SW E2 BACKLIGHT-SW
R3070 150
SD-DQ4 H1 DQ4 H4 NU VCOM-PWM
R3030 15x4 R3503
SD-DQ3 H3 DQ3 M2 SD-A12 10K
SD-DQ2 VSS *B N1 SD-A7
H7 DQ2
SD-DQ1 G2 DQ1 M3 SD-A3 R3510 22K CONTINUE
TO DIGITAL DIGITAL 5
SD-DQ0 G8 DQ0 P1 SD-BA2 MAIN 2
R3031 15x4 K2 SD-ODT IC3005(2/6) SW-EN
R3515 4.7K
L2 SD-A9 LED1 D14 LED1
*A:A1,A9,C1,C3,C7,C9,E1,E9, R3217 22
G1,G3,G7,G9,J1,J9,M9,R1 M1 SD-A5 AUDIO-MUTE C1 AUDIO-MUTE
R3213 22

2 *B:A3,A7,B2,B8,D2,D8,E3,E7,
F2,F8,H2,H8,J3,J7,N1,P9 R3032 15x4
L1
J2
K3
SD-A1
SD-A11
SD-A6
REMOTE C14
R3234
OPEN
REMOTE

K1 SD-A2
CONTINUE
J1 SD-A0 DIGITAL 4
R3033 15x4 J3 SD-RAS R3201 P-ON+1.8V
IC3006 R3215 22 33K
S25FL032P0XMFI010 R3102 H3 SD-CAS COMP-DET N12 P-ON+3.3V
(MEMORY) 10K
J4 SD-A10 AL+3.3V
1 CS VCC 8 K4 SD-BA1 P-ON+5V
R3107 C3073
10K 0.1
2 SO NU 7
R3089 47
P12 CS
3 WP SCK 6 R3092 47 CONTINUE
R11 SOUT DIGITAL 1
R3093 47
4 GND SI 5 P11 SIN C3072 10 CELL-PWR-CTRL
R3094 47 NU H14
R3479 T11 SCLK C3071 OPEN
10K R3095 22
T9 VBUS-EN
R9 VBUS-ST
C3246 D3052 C3348 R10 USBDP
(USB JACK) CN3009 1 OPEN 220/6.3V
T10 USBDN
BUS-POWER 1 R3099 5.6K
P10 NU
USBDN 2 IC3019

1 USBDP
GND
3
4 L3025
EXC24CG900U
C3327
1
BD2224G-TR
(HIGH SIDE SW)
1 VIN VOUT 5
2 GND
3 /EN /OC 4
R3480
10K

DIGITAL MAIN CBA UNIT

M N O P Q R
10-7 PL12.2SCAD3
Digital Main 4 Schematic Diagram [TYPE A]
1 NOTE:
The order of pins shown in this diagram is different from that of actual IC3005.
IC3005 is divided into six and shown as IC3005 (1/6) ~ IC3005 (6/6) in this Digital Main Schematic Diagram Section.

R3218
OPEN CONTINUE
*1 DIGITAL 3
IC3005(4/6) R3221 P-ON+1.8V
R8A05011BG-U0 100
DIGITAL SIGNAL PROCESS P-ON+3.3V
/MAIN MICRO CONTROLLER R3222 AL+3.3V
10K L3027
BEAD P-ON+5V
VCC33STB F12
C3160 C3182 R3106 R3100 R3036

4 VCC33STB G12

VDD12STB E12
0.1 OPEN

D
G
S
R3464
OPEN
Q3006
2SA1576UBTLQ
47K
R3105
10K
22K
Q3101
2SC4081UBTLQ
(SWITCHING)
D3105
OPEN D3103
HSC119
R3424
100 IC3004
100
CONTINUE
DIGITAL 6
P-ON+3.3V
(SWITCHING) L3001 BD00IC0WEFJ AL+3.3V
L3030 OPEN
0 Q3013 C3265 R3138 (+1.2V REG.) P-ON+3.3V(1)
C3181 SSM3K309T 10 OPEN
0.1 (SW+12V) L3015 R3423 D3115 1 VOUT VCC 8 P-ON+5V
OPEN R3097 47K HSC119 CONTINUE
2.2K C3024 C3108 C3027 DIGITAL 2
2 FB NU 7 10 OPEN OPEN
VDD12 *C Q3005 R3061 R3060 C3019 P-ON+3.3V
C3123 C3124 C3128 C3126 2SC4081UBTLQ 10K 2.7K 0.022
1 OPEN 1 OPEN (SWITCHING) D3104 3 GND NU 6 P-ON+5V
HSC119 R3059 R3062
D3101 2.7K 1.8K
HSC119 4 NU EN 5
CONTINUE
C3130 C3134 C3132 C3133 D3102 C3049 R3043 C3263 C3086 DIGITAL 1
OPEN 10 OPEN 10 L3020 HSC119 R3086 OPEN 180 OPEN 10 P-ON+5V
OPEN 4.7K
P-ON+21V
AVDD12 M10 Q3003 C3131 L3003 P-ON+3.3V
C3135 2SC4081UBTLQ 1 BLM21PG221SN1D
0.1 R3077
L3021 10K (SWITCHING) CONTINUE
BEAD IC3007 C3111 C3066 DIGITAL 5
AVDD12 E8 C3076 BD00IC0WEFJ OPEN OPEN RESET
AVDD12 F8 C3118 C3136 C3137 C3155 C3156 OPEN R3079 Q3004 (+1.8V REG.)
10 1 OPEN OPEN OPEN L3028 10K 2SC4081UBTLQ PROTECT1
AVDD12 F9 OPEN (SWITCHING) 1 VOUT VCC 8 PROTECT3
R3228 C3069 C3070
6.8K Q3011 2 FB NU 7 10 OPEN

3 VDDCLK G11

VCCQ18 H5
C3139
0.1 C3237 R3227
OPEN 1.2K
2SC4081UBTLQ
(SWITCHING) D3106
HSC119
R3111
10K
R3110
10K
R3109
3.3K
C3075
0.022
R3103
1.8K
3 GND
4 NU
NU 6
EN 5
CONTINUE
DIGITAL 1
PROTECT3
VCOM-PWM
L3014 OE2
VCCQ18 J5 C3326 C3325 C3324 C3343 C3266 OPEN C3264 C3079 R3042 C3084 C3087
10 OPEN OPEN 10 OPEN OPEN 220/6.3V OPEN OPEN 10
VCCQ18 M4 CONTINUE
DIGITAL 5
VCCQ18 T1 CHECK+1.8V
C3322 C3321 C3320 C3319 C3114 C3318
VCCQ18 M6 10 OPEN 10 10 OPEN 10 AL+3.3V
VCCQ18 N6 P-ON+5V
VCCQ18 M7 C3036 C3141 C3142 C3143 C3144 C3145 P-ON+3.3V(1)
VCCQ18 M8 1 1 OPEN 1 1 1
AMP+24V
C3081 C3082 C3122 C3080 C3103 C3102 C3007 C3002 C3012 C3001 P-ON+3.3V
OPEN OPEN IC3008 47/25V OPEN 4.7 4.7 OPEN IC3001 OPEN OPEN 47/25V
L3019 MP2305SDS-LF-Z R3133 MP2305SDS-LF-Z
(+1.2V REG.) (+3.3V REG.) CONTINUE
BEAD C3083 10K C3013 C3109 DIGITAL 3
AVDD33 E10 C3091 0.015 C3092 0.047 R3091 OPEN CELL-PWR-CTRL
1 BST SS 8 1 BST SS 8

R3136 OPEN
AVDD33 C2 C3148 C3149 C3150 C3117 OPEN OPEN 0
1 10 1 OPEN GPY10
AVDD33 C3 R3141 2 VIN EN 7 R3057 2 VIN EN 7 C3112 CPU-RESET-N
OPEN C3085 R3134 C3090 OPEN C3014 C3119 OPEN
AVDD33 E11 0.1 10K 1 0.1 OPEN P-ON-H2
C3147 D3113 3 SW COMP 6 3 SW COMP 6
OPEN MM5Z5V6B R3137 R3001 P-ON-H1
L3026 5.6K R3142 9.1K R3014
BEAD 4 GND FB 5 OPEN 4 GND FB 5 270 BACKLIGHT-ADJ
AVDD33 D6 C3088 C3017

2 L3006
BEAD
L3009
22uH
0.015 L3002
33uH
3300P BACKLIGHT-SW
VCOM-PWM

OPEN
OPEN

OPEN
OPEN
AVDD33 E6 R3602 C3094 C3067 C3097 C3096 R3149 C3099 C3065 R3601 C3020 C3101 C3021 C3059 R3004 C3060

270

100
100
100
C3151 C3152 C3154 D3114 OPEN 330/4V OPEN 10 10 3.9K OPEN OPEN OPEN 330/4V OPEN 10 10 33K OPEN
1 1 1 MM5Z5V6B L3016 C3606 R3145 C3605 R3003
OPEN OPEN 1.2K OPEN 6.2K

R3052
R3051
R3068
R3013
R3009
R3011
R3008
R3053
D3006 D3005
PTZTE255.1B TO POWER SUPPLY
VCCQ33 G4 PTZTE255.1B CN3701 CBA CN631
R3143 R3002
VCCQ33 F5 C3157 C3159 15K 15K 1 VCOM-PWM(NU)
1 1 2 BACKLIGHT-SW
VCCQ33 L12 D3107 D3011 OPEN
VCCQ33 K13 C3026 C3025 C3022 C3105 R3108 D3112 HSC119 3 BACKLIGHT-ADJ
OPEN OPEN OPEN 4.7 47K MM5Z12B D3012 OPEN
VCCQ33 J12 4 PROTECT3
IC3003 R3154 5 PROTECT1
AVDD33 N11 MP2305SDS-LF-Z R3140 Q3009 OPEN
(+5V REG.) 20K 2SC4081UBTLQ 6 P-ON-H1(NU)
C3028
C3095 0.047 R3112 R3115 Q3103 C3238 R3139 (SWITCHING) 7 P-ON-H2
VSS *D OPEN 1 BST SS 8 10K OPEN 2SA1576UBTLQ R3101 OPEN 1K
R3098 (SWITCHING) 1K 8 RESET
0 R3153
R3054 2 VIN EN 7 C3601 C3015 C3016 D3607 OPEN 9 OE2(NU)
*C:G5,G6,H6,J7,J11,J13,K6,K7, OPEN C3042 C3121 C3107 R3104 OPEN OPEN OPEN OPEN
K11,L8,L9,M9,N9,P9,M11. 0.1 OPEN Q3102 1 1K 10 GND
3 SW COMP 6 2SC4081UBTLQ R3113
*D:D2~D5,D12,E3~E5,E7,E9,F4,F6, R3005 (SWITCHING) 10K 11 AL+3.3V
5.6K C3604 C3603 D3602
F7,F10,F11,G7~G10,H7~H13,J6, 4 GND FB 5 10 1 MM5Z5V6B 12 GND
J8~J10,K5,K8~K10,K12,L5~L7, C3043 R3114 R3072
L10,L11,P2,T8 L3005 0.015 47K 100 13 AMP+24V
22uH 14 AMP+24V
R3603 C3053 C3074 C3056 R3012 C3104 D3007 C3044 C3011 C3046 15 GND

1 OPEN 220/6.3V 10 10 33K OPEN OPEN OPEN OPEN OPEN

OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
16 P-ON+21V
C3607 R3007
OPEN 12K 17 P-ON+21V

C3055
C3063
C3062
C3048
C3008
C3004
C3006
C3003
C3064
18 GND
R3006 C3146 C3138 C3153
10K OPEN OPEN OPEN 19 GND
20 GND
21 GND
22 P-ON+21V
DIGITAL MAIN CBA UNIT 23 P-ON+21V

S T U V W X
10-8 PL12.2SCDA4
Digital Main 5 Schematic Diagram [TYPE A]
1 NOTE:
The order of pins shown in this diagram is different from that of actual IC3005.
IC3005 is divided into six and shown as IC3005 (1/6) ~ IC3005 (6/6) in this Digital Main Schematic Diagram Section.
CONTINUE
DIGITAL 4
CHECK+1.8V R5124 R5104
OPEN R5113 OPEN R5106 R5111
AL+3.3V OPEN Q5104 Q5105 OPEN OPEN
*1 OPEN OPEN
P-ON+5V IC3005(5/6)
P-ON+3.3V(1) R8A05011BG-U0 R5110
DIGITAL SIGNAL PROCESS R5112 D5107 R5114 OPEN
AMP+24V R3537 /MAIN MICRO CONTROLLER OPEN OPEN OPEN
P-ON+3.3V OPEN
Q5103
CONTINUE R3535 R3312 10K SW-PU-CONT E1 OPEN
DIGITAL 3 R3532 OPEN Q3530 R3533 D13 NU R5109 R5107 C5105

4 SW-EN
LED1
AUDIO-MUTE
OPEN OPEN OPEN
Q3502
2SA1576UBTLQ
(LED DRIVE) FACTORY-SEL G1
R5121
OPEN
R5125
OPEN
OPEN OPEN

Q5110
OPEN

R5126
OPEN
R5123
OPEN

C5106
OPEN
REMOTE OPEN
R3558 R3559 R5127
R3534 OPEN 10K OPEN
OPEN
TO FUNCTION R3552 R3560 R3216
CBA CN4001 CN3101 100 100K 100
SDA 1 SM-MISO/PWR J16
R5103 IC5101 C5103
SCL 2 OPEN Q5109 OPEN OPEN
Q3531 OPEN
GND 3 OPEN R5119
OPEN 1 OE VCC 5
KEY-IN1 4 C3555 R3402 0
C3559 OPEN R3320 Q5108 2 A

R3318 22K
R3317 10K
R3319 10K
REMOTE 5 OPEN R3551 R3555 OPEN OPEN
100 OPEN R5120
LED1 6 R3183 OPEN 3 GND Y 4 R5115
OPEN Q3010 C3330 OPEN R3401 0 OPEN
LIGHT 7 OPEN
C3553 C3556 C3557 C3558 C3329 0.01
P-ON+5V 8 OPEN OPEN OPEN OPEN R5108 D5106 R5102
D3116 OPEN R5117 R5118 R5101 R5105 OPEN OPEN OPEN
AL+3.3V 9 OPEN OPEN OPEN OPEN
C3554 0R3536 Q3501 R3185 R5122 L5101 CN5101 (NO CONNECTION)
1 2SC4081UBTLQ OPEN OPEN OPEN
(LED DRIVE) C3323 OPEN SM-CLK K16 1 SM-CLK
C3551 33P C5104 Q5102 L5102
R3184 R3186 A15 KEY-IN1 OPEN OPEN OPEN 2 SM-MISO
CONTINUE C3552 33P R3553 D3501 OPEN OPEN R3314 22 R3210 3 NU
DIGITAL 4 100 MM5Z5V6B B13 PROTECT3 100

3 RESET
PROTECT1
PROTECT3
R3315
R3316
R3208
OPEN
22
0
A13
C13
C12
LIGHT-SENS
PROTECT1
LPF
SM-MOSI/HPD-SINK K14

TO DIGITAL TO DIGITAL
C5102
OPEN
Q5101
OPEN
L5103
OPEN
L5104
4
5
6
SM-MISI
GND
REMOTE
C3231 MAIN 2 MAIN 6 OPEN

C5101 OPEN

OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
0.22 IC3005(2/6) IC3005(6/6) Q5106

1000P

1000P
R3556 R3557 C3328 OPEN

OPEN
OPEN

OPEN

OPEN
CONTINUE 10 10 OPEN R3340 10K
DIGITAL 2 NU D11

D5105
C5109
D5104
C5108
D5103
D5102
C5107
D5101
C3219 10
SCL NU D7
C3222
C3221
C3233
R3500
C3232
R3499
C3220 10 Q5107 CONTINUE
SDA NU C6 OPEN DIGITAL 6
R3335 18K C3217 10 C3216 10 HPD-SINK
AUDIO(L)-IN A8 NU C5
R3336 18K C3218 10 PWR
AUDIO(R)-IN B8 AUDIO NU B6
R3224 0 I/F CONTINUE
B7 NU A6 R3209 DIGITAL 2
R3225 0 100
A7 N10 SPDIF
R3823 CONTINUE
10K R3191 DIGITAL 3
100
RESET J15 CPU-RESET-N
R5116 D3111 BACKLIGHT-SW
R3561 OPEN MM5Z5V6B
10
R3322
0
R3811 IC3009
10K R3501 C3227 C3808 R3178 PST8429UR R3182 D3109
C3818 10 100K 2200P 1 C3819 10 220 (RESET) 56K OPEN

2 R3812
10K
C3817 4.7
30 29 28 27 26 25 24 23 22 21
R3810 27K

D3108
OPEN
C3106
1
C3252
OPEN
1 GND OUT 4
2 VDD CD 3
C3113
0.033
C3116
1000P D3110
OPEN
VREFF
PROT

AVCC
ROSC
GND
GND
GND
GND
GND
NU

R3325 R3814 C3820


0 OPEN 10
31 GND CBIAS 20
C3809
1 R3828
32 19 OPEN
R3502 C3229 Q3803
100K 2200P 33 18 R3809 2SA1576UBTLQ
R3808 OPEN R3818
0 10K (SWITCHING) R3802 C3802
34 CONTROL 17 180 OPEN
R3806 R3813 LOGIC C3833 R3819 R3827
39K 33K C3821 R3807 OPEN 100K R3817 OPEN
0.1 35 GND GND 16 OPEN 47K R3805
10K C3804 JK3703
Q3801 36 GND GND 15 R3816 Q3802 100/35V HEADPHONE
2SC4081UBTLQ 10K 2SC4081UBTLQ R3801 JACK
(SWITCHING) (SWITCHING) 180
37 VDD PWM PWM VDD 14 C3823
GENE. GENE. 100/35V C3801
C3827 C3816 R3815 OPEN
100/35V 0.1 38 VDD VDD 13 47K C3832
L3801 100/35V L3803
33uH OPEN
39 12
D3801 R3804 C3811 C3825 C3837 C3838 R3825 C3830
40 11 MM5Z33B 10 0.1 0.1 OPEN OPEN OPEN OPEN
C3806 C3810
DVDD1

1000P 100/35V R3821

1
GND
HB2

GND
GND
GND
GND
GND
HB1
GND

IC3801 OPEN
R2A15122FP 1 2 3 4 5 6 7 8 9 10 L3802 C3822
-W00R 33uH 100/35V
(AUDIO AMP) SP3801
C3813 D3802 C3835 C3836 CN3801 SPEAKER
0.1 MM5Z33B R3803 C3812 C3824 OPEN OPEN C3803 C3807 L-CH
C3814 C3828 R3826 10 0.1 0.1 100/35V OPEN 1 SP(L)
0.1 10 0 C3805 2 GND
1000P R3820
OPEN 3 GND
Q3804 4 SP(R) SP3802
OPEN C3834 R3822 R3824
C3829 C3815 C3826 C3831 OPEN OPEN OPEN SPEAKER
DIGITAL MAIN CBA UNIT 100/35V 0.1 100/35V OPEN R-CH

Y Z AA BB CC DD
10-9 PL12.2SCAD5
Digital Main 6 Schematic Diagram [TYPE A]
1 NOTE:
The order of pins shown in this diagram is different from that of actual IC3005.
IC3005 is divided into six and shown as IC3005 (1/6) ~ IC3005 (6/6) in this Digital Main Schematic Diagram Section.

CONTINUE HDMI-
DIGITAL 4 JK3002 CONNECTOR-2
P-ON+3.3V 1 TMDS-D2(+)
AL+3.3V L3046 C3316 C3300 C3302 C3304 C3306 C3308
OPEN 10 OPEN OPEN OPEN OPEN OPEN 2 D-SHIELD0
P-ON+3.3V(1) 3 TMDS-D2(-)
P-ON+5V 4 TMDS-D1(+)
C3310 C3312 C3314 C3331 C3333
OPEN OPEN OPEN OPEN OPEN 5 D-SHIELD1
6 TMDS-D1(-)
C3420 C3422 C3424 C3427 7 TMDS-D0(+)
OPEN OPEN OPEN OPEN

4 *1
IC3005(6/6)
R8A05011BG-U0
DIGITAL SIGNAL PROCESS Q3014
C3421
1
C3423
1
C3425
1
C3426
1
8
9
10
11
D-SHIELD2
TMDS-D0(-)
TMDS-CLOCK(+)
C-SHIELD0
/MAIN MICRO CONTROLLER 2SK3018 R3405 12 TMDS-CLOCK(-)
(BUFFER) 100
13 HDMI-CEC
TO DIGITAL TO DIGITAL 14 NU
MAIN 2 MAIN 5
IC3005(2/6) IC3005(5/6) R3415 15 HDMI-CLOCK
82K R3486
4.64K 16 HDMI-DATA
D3057 IC3018 17 GND
RB751S-40 BU16029KV-E2
VIDEO AUDIO 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 18 +5V
DECODER DECODER R3237 (HDMI SW)

GND

VCC

GND

VCC

GND
NU
27K C3023 R3066 R3055 19 HOT PLUG DETECT
HDMI-CEC B15 0.1 2.7K 1K

17 HOT-PLUG- 64 R3056 R3067


DETECT3 OPEN OPEN
18 63
R3063
R3489 1K Q3008
B1 10K 19 VCC 62 2SC4081UBTLQ
A1 R3058 (SWITCHING)
20 VCC 61 10K HDMI-
B2 JK3003 CONNECTOR-3
A2 21 60 1 TMDS-D2(+)
HDMI
I/F B3 2 D-SHIELD0
22 GND 59
A3 3 TMDS-D2(-)
B4 23 GND 58 4 TMDS-D1(+)
A4 5 D-SHIELD1

3 C3990
OPEN
24
25 VCC
26
HDMI SW 57
56
VCC 55
6
7
8
TMDS-D1(-)
TMDS-D0(+)
D-SHIELD2
9 TMDS-D0(-)
27 54 10 TMDS-CLOCK(+)
R3488 R3487
C3992 C3991 4.7K 4.7K 11 C-SHIELD0
OPEN OPEN 28 GND 53
12 TMDS-CLOCK(-)
HDMI1-SCL C16 29 SCL-SINK 52 13 HDMI-CEC
14 NU
HDMI1-SDA C15 30 SDA-SINK 51
R3514 15 HDMI-CLOCK
100
HPD-SINK F13 31 HOT-PLUG-
DETECT-SINK
HOT-PLUG- 50
DETECT2 16 HDMI-DATA
R3508
22 17 GND

HOT-PLUG-
HDMI-SEL0 G3 32 HDMI-
SEL0 NU 49

DETECT1
R3496 18 +5V
R3494

HDMI-
4.7K C3005 R3019 R3010

SEL1
HDMI-SEL1 F1 OPEN 19 HOT PLUG DETECT

VCC

GND

VCC
0.1 2.7K 1K

NU
R3509
NU G2 22
R3991 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 R3015 R3020
OPEN OPEN OPEN
R3018
1K Q3001
R3497 2SC4081UBTLQ
4.7K R3992 R3017 (SWITCHING)
R3990 OPEN 10K HDMI-
R3236 C3185 R3270 C3187 OPEN JK3004 CONNECTOR-1
560 0.01 2.2K 2.2 1 TMDS-D2(+)
EXT-RES C4 C3186 R3453 2 D-SHIELD0

2 PLL-XFC-A B5
PLL-XFC-P A5 R3271
3K
4700P
C3188
2200P
1.5K

R3451
10K
3
4
5
TMDS-D2(-)
TMDS-D1(+)
D-SHIELD1
6 TMDS-D1(-)
Q3451 R3452 7 TMDS-D0(+)
2SC4081UBTLQ 10K
(SWITCHING) 8 D-SHIELD2
PWR M12 9 TMDS-D0(-)
D3993 10 TMDS-CLOCK(+)
OPEN
11 C-SHIELD0
12 TMDS-CLOCK(-)
HDMI-SDA F14 13 HDMI-CEC
HDMI-SCL G14 14 NU
15 HDMI-CLOCK
16 HDMI-DATA
R3022 R3024 D3003 D3002 17 GND
10K 10K HSC119 HSC119
18 +5V
R3023 R3025 C3018 R3040 19 HOT PLUG DETECT
33K 1K 0.1 2.7K
CONTINUE
DIGITAL 5
HPD-SINK C3213
IC3011 OPEN D3001 R3026
PWR BU9883FV-WE2 HSC119 OPEN R3050
R3276 R3273 (HDMI SERIAL EEPROM) OPEN
47K 47K
1 VCC1 VCC2 16 R3029
C3228 OPEN R3212 R3214 1K Q3002

1 CONTINUE
DIGITAL 2
VGA-SDA
VGA-SCL
R3192
4.7K

R3193
C3226 OPEN
2 SCL1
3 SDA1
4 WPB
SCL2 15
SDA2 14
NU 13
47K 47K
C3190
OPEN
R3027
10K
2SC4081UBTLQ
(SWITCHING)

4.7K R3523 C3192 0.1 C3235 C3236


OPEN 5 VCC-OUT GND 12 R3275 R3278 OPEN OPEN
R3281 47K 47K
100
R3282 6 SDA0 SDA3 11
100
7 SCL0 SCL3 10
8 VCC0 VCC3 9
C3271
C3272
OPEN OPEN C3191
0.1
C3215
OPEN
C3225
OPEN
C3212
OPEN
C3230
OPEN
C3234
OPEN DIGITAL MAIN CBA UNIT

EE FF GG HH II JJ
10-10 PL12.2SCAD6
Digital Main 1 Schematic Diagram [TYPE B]
1 NOTE:
The order of pins shown in this diagram is different from that of actual IC3101.
IC3101 is divided into eight and shown as IC3101 (1/8) ~ IC3101 (8/8) in this Digital Main Schematic Diagram Section.

CONTINUE
DIGITAL 8
P-ON+12V/+21V
(NO CONNECTION) CN3905
LCD+5V 1 P-ON+5V
LCD+5V 2
LCD+5V 3 D3905 R3952 R3942 R3929 C3900
OPEN OPEN 0 OPEN OPEN
LCD+5V 4 Q3903
Q3905 OPEN
LCD+5V 5 IC3901 D3906 C3996 OPEN D S
OPEN OPEN
GND 6 OPEN C3946 1 8 TO LCD PANEL
OPEN R3934 R3932 CN3904 ASSEMBLY
GND 7 1 BS SS 8 G C3995 R3894 3.9K 18K 30 LCD+21V
2 7 OPEN OPEN

4 LV-ED3(+) 8
LV-ED3(-) 9
GND 10
LV-ECLK(+) 11
C3957
OPEN
C3943
OPEN
C3949
OPEN
C3944
OPEN
2 EN
3 SW
EN 7
COMP 6
R3550
OPEN
C3951
OPEN
R3899
OPEN
3
4
6
5
C3948
0.1
C3947
47/25V
R3933
12K

R3935
R3931
11K
29
28
27
LCD+21V
GND
VCOM-DC
R3891 R3895 1K Q3901 26 PWR-CTRL
LV-ECLK(-) 12 4 GND FB 5 R3897 OPEN OPEN 2SC4081UBTLQ
R3937 R3936 OPEN (DRIVE) 25 P-ON+3.3V
GND 13 R3938 OPEN OPEN Q3904
OPEN OPEN R3892 24 GND
LV-ED2(+) 14 C3950 R3898 C3997 Q3902 OPEN
OPEN OPEN OPEN OPEN 23 LVDS-OD0(-)
LV-ED2(-) 15 L3901 R3939 C3994 R3893 22 LVDS-OD0(+)
LV-ED1(+) 16 OPEN OPEN OPEN OPEN
21 LVDS-OD1(-)
LV-ED1(-) 17 R3927 C3953 C3956 C3954 D3901 C3952 C3958 C3959 R3911 R3912 20 LVDS-OD1(+)
GND 18 OPEN OPEN OPEN OPEN OPEN 47/25V OPEN OPEN OPEN OPEN
C3970 19 LVDS-OD2(-)
LV-ED0(+) 19 OPEN 18 LVDS-OD2(+)
LV-ED0(-) 20 17 GND
R3953 OPEN
GND 21 16 LVDS-OCLK(-)
R3951 OPEN
GND 22 15 LVDS-OCLK(+)
R3950 OPEN
NU 23 14 GND
R3949 OPEN
NU 24 13 LVDS-OD3(-)
GND 25 12 LVDS-OD3(+)
R3948 OPEN
NU 26 11 LVDS-OD4(-)
R3947 OPEN
NU 27 10 LVDS-OD4(+)
R3946 OPEN
NU 28 9 LVDS-OD5(-)
R3943 OPEN
NU 29 8 LVDS-OD5(+)
R3918 OPEN
NU 30 7 GND
R3917 OPEN
GND 31 6 TP

3
OPEN
OPEN
OPEN
OPEN

5 POL
4 CPV
R3890
R3889
R3870
R3862

3 OE
2 OE2
(NO CONNECTION) CN3906 1 STV
LCD+12V 1
LCD+12V 2 R3924 CN3903 (NO CONNECTION)
OPEN
LCD+12V 3 31 LCD+21V

OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
LCD+12V 4 R3923 30 LCD+21V
OPEN
NU 5 29 LCD+21V

C3926
C3927
C3928
C3929
C3930
C3931
C3932
C3933
C3934
C3935
C3936
C3937
C3960
C3961
GND 6 *1 28 GND
IC3101(1/8) R3926 0
GND 7 MN2WS0172A 27 VCOM-DC
R3922 0
GND 8 DIGITAL SIGNAL PROCESS 26 PWR-CTRL
/MAIN MICRO CONTROLLER R3920 0
GND 9 25 P-ON+3.3V
R3916 R3925
GND 10 10K OPEN 24 GND
R3888 OPEN R3534 0
NU 11 J6 L4 23 LVDS-OD0(-)
R3887 OPEN R3535 0
NU 12 J7 L5 22 LVDS-OD0(+)
R3971 OPEN R3536 0
LV-ED3(+) 13 G2 L3 21 LVDS-OD1(-)
R3970 OPEN R3537 0
LV-ED3(-) 14 G1 L2 20 LVDS-OD1(+)
R3538 0
GND 15 K5 19 LVDS-OD2(-)
R3969 OPEN R3539 0
LV-ECLK(+) 16 H4 K4 18 LVDS-OD2(+)
R3968 OPEN LVDS
LV-ECLK(-) 17 G4 TX 17 GND
R3540 0
GND 18 K3 16 LVDS-OCLK(-)
R3965 OPEN R3541 0

2 LV-ED2(+) 19
LV-ED2(-) 20
LV-ED1(+) 21
LV-ED1(-) 22
R3962
R3961
R3959
OPEN
OPEN
OPEN
H1
G3
H2
H3
L1

J5
J4
R3542
R3543
OPEN
OPEN
15
14
13
12
LVDS-OCLK(+)
GND
LVDS-OD3(-)
LVDS-OD3(+)
R3958 OPEN R3544 OPEN
LV-ED0(+) 23 J2 K1 11 LVDS-OD4(-)
R3957 OPEN R3545 OPEN
LV-ED0(-) 24 J3 K2 10 LVDS-OD4(+)
R3532 OPEN
GND 25 K7 9 LVDS-OD5(-)
R3533 OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN

GND 26 F2 NU K6 8 LVDS-OD5(+)
R3886 OPEN
NU 27 F3 NU NU P7 7 GND
R3885 OPEN R3974 100
C3914
C3915
C3916
C3917
C3918
C3919
C3920
C3921
C3922
C3923
C3924
C3925

NU 28 TP A2 6 TP
R3975 100
LV-OD3(+) 29 POL D4 5 POL
TO DIGITAL R3976 100
LV-OD3(-) 30 MAIN 5 CPV B3 4 CPV
IC3101(5/8) R3977 100
GND 31 OE B2 3 OE
R3978 100
LV-OCLK(+) 32 OE2 D5 2 OE2
R3979 100
LV-OCLK(-) 33 STV C3 1 STV

100K
100K
100K
100K
100K
100K

OPEN
OPEN
OPEN
OPEN
OPEN
100P
GND 34
R3944 OPEN R3945
LV-OD2(+) 35 NU C4 OPEN R3930
R3980 OPEN OPEN

R3884
R3928
R3883
R3882
R3881
R3880

C3942
C3998
C3941
C3940
C3939
C3938
LV-OD2(-) 36 NU B1
LV-OD1(+) 37 BACKLIGHT-ADJ G6
LV-OD1(-) 38 VCOM-PWM D3 CONTINUE
R3901 DIGITAL 3
LV-OD0(+) 39 10K
LV-OD0(-) 40 FRC-CTRL3

1 GND 41
NU 42
NU 43
NU 44
R3866 OPEN
R3867 OPEN
R3868 OPEN C3903 C3902 R3896 R3900 OPEN
CONTINUE
DIGITAL 6
P-ON+3.3V
CONTINUE
DIGITAL 7
OPEN OPEN OPEN R3903 OPEN
NU 45 VCOM-PWM
R3905 OPEN
NU 46 LCD-PON
R3869 OPEN R3940 R3941 C3909 C3910
NU 47 OPEN OPEN OPEN OPEN BACKLIGHT-ADJ
R3906 OPEN
NU 48 D3902 OE2
R3907 OPEN R3902 OPEN OPEN
NU 49 PROTECT3
NU 50 C3901 C3904
OPEN OPEN
GND 51
DIGITAL MAIN CBA UNIT

A B C D E F
10-11 PL12.2SCBD1
Digital Main 2 Schematic Diagram [TYPE B]
1 NOTE:
The order of pins shown in this diagram is different from that of actual IC3101.
IC3101 is divided into eight and shown as IC3101 (1/8) ~ IC3101 (8/8) in this Digital Main Schematic Diagram Section.

*1
IC3101(2/8)
MN2WS0172A DIGITAL MAIN CBA UNIT
MAIN MICRO CONTROLLER
/DIGITAL SIGNAL PROCESS CONTINUE
R3429 1K DIGITAL 6
MMVCAL M10 VCC+1.5V
R3431 270
MMVREF0 G10
R3433 270 IC3401 IC3402
MMVREF1 G18
K4B1G1646G-BCH9 K4B1G1646G-BCH9
MMDQ0 (DDR3 SDRAM) (DDR3 SDRAM)
MMDQ0 C6
MMDQ1 D6 MMDQ1 C3401 R3430 C3402 R3432 C3403 R3434 MMA13 MMA13
1K

4 MMDQ2
MMDQ3
MMDQ4
B6
A5
E6
MMDQ2
MMDQ3
MMDQ4
0.1 OPEN 270 OPEN 270
MMA12
MMA11
MMA10
T3
N7
R7
L7
A13
A12/BC#
A11
A10/AP
VDD1
VDD2
VDD3
VDD4
B2
D9
G7
K2
C3404
10
C3405
0.1
C3406
0.1
C3407
0.1
MMA12
MMA11
MMA10
T3
N7
R7
L7
A13
A12/BC#
A11
A10/AP
VDD1
VDD2
VDD3
VDD4
B2
D9
G7
K2
C3414
10
C3415
0.1
C3416
0.1
C3417
0.1

MMDQ5 B5 MMDQ5 MMA9 MMA9


R3 A9 VDD5 K8 C3408 C3409 C3410 C3411 R3 A9 VDD5 K8 C3418 C3419 C3420 C3421
MMDQ6 A4 MMDQ6 MMA8 0.1 0.1 0.1 0.1 MMA8 0.1 0.1 0.1 0.1
MMDQ7 T8 A8 VDD6 N1 T8 A8 VDD6 N1
MMDQ7 C5 MMA7 R2 A7 VDD7 N9 MMA7 R2 A7 VDD7 N9
MMDQ8 D8 MMDQ8 MMA6 MMA6
R8 A6 VDD8 R1 C3412 C3431 R8 A6 VDD8 R1 C3422 C3432
MMDQ9 C8 MMDQ9 MMA5 0.1 10 MMA5 0.1 10
MMDQ10 P2 A5 VDD9 R9 P2 A5 VDD9 R9
MMDQ10 C9 MMA4 P8 A4 VDDQ1 A1 MMA4 P8 A4 VDDQ1 A1
MMDQ11 B9 MMDQ11 MMA3 MMA3
MMDQ12 N2 A3 VDDQ2 A8 N2 A3 VDDQ2 A8
MMDQ12 B10 MMA2 P3 A2 VDDQ3 C1 MMA2 P3 A2 VDDQ3 C1
MMDQ13 C10 MMDQ13 MMA1 MMA1
MMDQ14 P7 A1 VDDQ4 C9 P7 A1 VDDQ4 C9
MMDQ14 F8 MMA0 N3 A0 VDDQ5 D2 MMA0 N3 A0 VDDQ5 D2
MMDQ15 E7 MMDQ15
MMDQ16 M7 NU VDDQ6 E9 M7 NU VDDQ6 E9
MMDQ16 E17 VDDQ7 F1 VDDQ7 F1
MMDQ17 F17 MMDQ17
MMDQ18 VDDQ8 H2 VDDQ8 H2
MMDQ18 G17 VDDQ9 H9 VDDQ9 H9
MMDQ19 F18 MMDQ19
MMDQ20 C7 DQSU C7 DQSU
MMDQ20 C18 B7 DQSU# R3435 B7 DQSU# R3439
MMDQ21 B18 MMDQ21 270 270
MMDQ22 F3 DQSL VREFCA M8 F3 DQSL VREFCA M8
MMDQ22 B19 G3 DQSL# G3 DQSL#
MMDQ23 R3436 C3413 C3429 R3440 C3423 C3430
MMDQ23 C19 D3 DMU 270 0.1 0.1 D3 DMU 270 0.1 0.1
MMDQ24 F16 MMDQ24
E7 DML E7 DML

3 MMDQ25
MMDQ26
MMDQ27
E15
D16
C16
MMDQ25
MMDQ26
MMDQ27
MMDQ28
MMDQ1
MMDQ3
A3
B8
DQU7
DQU6
VREFDQ H1

VSS1
VSS2
A9
B3
MMDQ28
MMDQ24
A3
B8
DQU7
DQU6
VREFDQ H1

VSS1
VSS2
A9
B3
MMDQ28 B15 MMDQ2 MMDQ27
MMDQ29 C15 MMDQ29 A2 DQU5 VSS3 E1 A2 DQU5 VSS3 E1
MMDQ30 MMDQ5 A7 DQU4 VSS4 G8 MMDQ30 A7 DQU4 VSS4 G8
MMDQ30 A14 MMDQ0 MMDQ29
MMDQ31 B14 MMDQ31 C2 DQU3 VSS5 J2 C2 DQU3 VSS5 J2
MMDQ7 C8 DQU2 VSS6 J8 MMDQ25 C8 DQU2 VSS6 J8
MMDQS0 B7 MMDQ4 C3 DQU1 VSS7 M1 MMDQ31 C3 DQU1 VSS7 M1
MMXDQS0 A7 MMDQ6 D7 DQU0 VSS8 M9 MMDQ26 D7 DQU0 VSS8 M9
MMDQS1 B8 MMDQ13 H7 DQL7 VSS9 P1 MMDQ16 H7 DQL7 VSS9 P1
MMXDQS1 A8 MMDQ15 G2 DQL6 VSS10 P9 MMDQ23 G2 DQL6 VSS10 P9
MMDQS2 B17 MMDQ11 H8 DQL5 VSS11 T1 MMDQ18 H8 DQL5 VSS11 T1
MMXDQS2 A17 MMDQ14 H3 DQL4 VSS12 T9 MMDQ22 H3 DQL4 VSS12 T9
MMDQS3 B16 MMDQ9 F8 DQL3 VSSQ1 B1 MMDQ17 F8 DQL3 VSSQ1 B1
MMXDQS3 A16 MMDQ8 F2 DQL2 VSSQ2 B9 MMDQ19 F2 DQL2 VSSQ2 B9
MMDQ10 F7 DQL1 VSSQ3 D1 MMDQ21 F7 DQL1 VSSQ3 D1
MMDM0 C7 MMDQ12 MMDQ20
MMDM1 D7 E3 DQL0 VSSQ4 D8 E3 DQL0 VSSQ4 D8
MMDM2 D17 VSSQ5 E2 VSSQ5 E2
MMDM3 C17 VSSQ6 E8 VSSQ6 E8
VSSQ7 F9 VSSQ7 F9
MMA0 B13 MMA0 L2 CS# VSSQ8 G1 L2 CS# VSSQ8 G1
MMA1 D10 MMA1 K3 CAS# VSSQ9 G9 K3 CAS# VSSQ9 G9
MMA2 F10 MMA2 K1 ODT R3437 K1 ODT R3441

2 MMA3
MMA4
MMA5
G12
G9
C11
MMA3
MMA4
MMA5
J3
L3
RAS#
WE#
T2 RESET#
CK J7
CK# K7
CKE K9
220 J3
L3
RAS#
WE#
T2 RESET#
CK J7
CK# K7
CKE K9
220

MMA6 D9 MMA6 L8 ZQ L8 ZQ
MMA7 F12 MMA7 R3438 NU J1 R3442 NU J1
MMA8 240 240
MMA8 F11 NU J9 NU J9
MMA9 E9 MMA9 M3 BA2 NU L1 M3 BA2 NU L1
MMA10 C13 MMA10 N8 BA1 NU L9 N8 BA1 NU L9
MMA11 D11 MMA11 M2 BA0 NU T7 M2 BA0 NU T7
MMA12 G13 MMA12
MMA13 A10 MMA13

MMBA0 G14
MMBA1 C12
MMBA2 D14
MMCK A11
MMXCK B11
R3420 33
MMXCS0 F14
R3421 33
MMXCS1 E14
MMXRAS G11
MMXCAS B12

1 MEMORY
I/F MMXWE
MMODT0
MMODT1
A13
E11
C14
R3425
R3426
R3446
33
33
33
MMCKE0 E10
R3447 33
MMCKE1 F15
TO DIGITAL
MAIN 5 MMXRESET D13
IC3101(5/8) MMRODT N10 R3427
R3428 10K
240

G H I J K L
10-12 PL12.2SCBD2
Digital Main 3 Schematic Diagram [TYPE B]
1 NOTE:
The order of pins shown in this diagram is different from that of actual IC3101.
IC3101 is divided into eight and shown as IC3101 (1/8) ~ IC3101 (8/8) in this Digital Main Schematic Diagram Section.

CONTINUE
(NO CONNECTION) CN3111 DIGITAL 6
GND 2 AL+3.3V
BOOTSWAP 1 P-ON+3.3V

R3135 OPEN
*1

R3137 10K
R3134 10K

R3222 10K
R3223 10K
IC3101(3/8)
MN2WS0172A
DIGITAL SIGNAL PROCESS
/MAIN MICRO CONTROLLER

4 E23
H25
B25
EAS
ECLK
ERXW
ED0
ED1
ED2
K20
A25
J20
R3115
R3116
R3129
100
100
100
ED0
ED1
ED2
C3125 C3126
R3216 B26 ESZ0 R3130 100 ED3 0.1 0.1
OPEN ED3 B24
C26 ESZ1 R3131 100 ED4
ED4 E22
D26 XECS0 R3166 100 ED5 IC3102
ED5 H20 K9F2G08U0C-SCB0
F23 XECS1 R3167 100 ED6 (NAND FLASH MEMORY)
ED6 A24
C25 XECS3 R3168 100 ED7
MEMORY ED7 F21
F22 NU I/F NU G20 1 NU NU 48
D23 XERE NU C23 2 NU NU 47
G21 XEWE0 NU D22
C24 XEWE1 BC3105 3 NU NU 46
NU A23 0
CONTINUE
DIGITAL 1 E1 XDBG-IRQ NU B23
R3195 OPEN 4 NU NU 45

R3132 OPEN
FRC-CTRL3 U2 FRC-RDY-1

R3124 10K
NU F20 ED7
U3 XIRQ3 NU A22 5 NU I/O7 44
CONTINUE
DIGITAL 4 R3199 T6 XIRQ4 NU E21 ED6
OPEN 6 NU I/O6 43
XRST1 V2 XIRQ5
R3171 22 ED5
T5 XIRQ6 NANDRYBY A19 7 R/B I/O5 42
TO DIGITAL R3172 22
U6 XIRQ7 NFALE C20 ED4
MAIN 5 R3173 100 8 RE I/O4 41
CONTINUE L20 PCCD1 IC3104(5/8) NFCLE B20
DIGITAL 7 R3174 100
M24 PCREADY XNFCE E19 9 CE NU 40
RESET R3175 39
D2 N4 XNFWE G19
R3176 100 10 NU NU 39
R3203 E4 RMC0 XNFWP F19
R3177 39

3 56K

IC3104
4
OUT
3
CD
C3132
0.047
C3131
1000P
R3185
OPEN
R3198
AB6 XRSTSTM XNFRE
NU
NU
A20
L24
N26
R3128
10K
R3123
10K
11 NU
12 VCC
NU 38
VCC 37

PST8429UR 10K NU N24 13 VSS VSS 36


(RESET) GND VDD R3208 AC3 XRST NU M20
1 2 OPEN 14 NU NU 35
NU L25
R3138 10K
R3192 NU Y25 15 NU NU 34
220 R3139 10K
NU W25
(NO CONNECTION) CN3104 C3101 R3630 C3102 C3129 R3140 10K 16 CLE NU 33
GND 10 1 270 OPEN D3102 R3111 OPEN NU V24
OPEN OPEN R3141 10K ED3
RESET 9 NU T23 17 ALE I/O3 32
R3142 10K
EJTCK 8 AC26 EJTCK NU Y26 ED2
R3143 10K 18 WE I/O2 31
JTDI 7 Y22 JTDI NU W26
R3144 10K ED1
JTDO 6 AA25 JTDO NU W24 19 WP I/O1 30
R3145 10K
JTMS 5 AB24 JTMS NU Y24 ED0
R3264 10K 20 NU I/O0 29
TRSTN 4 W20 TRSTN NU T21
EVTRG 3 D25 BOOTSWAP 21 NU NU 28
R3127 R3112 R3113 R3093 R3094 NU V4
XRST 2 10K 10K 10K OPEN OPEN 22 NU NU 27
AL+3.3V 1 M6 NU EA0 J21
R3240 1K R3236 1K
Q3182 M5 NU EA1 H26 23 NU NU 26
C3962 D3181 D3182 R3184 OPEN EA2 H22
OPEN OPEN OPEN OPEN L7 NU 24 NU NU 25
M4 NU EA3 G24
R3227 1K
R3180 R3183 M3 NU EA4 G26
CONTINUE OPEN OPEN
DIGITAL 9 R3099 L6 NU EA5 H23
OPEN Q3181

2 PWR-DETECT
C3190
OPEN
OPEN M2
M7
NU
NU

N1 EVTRG
EA6
EA7
EA8
EA9
G25
F24
J22
F25
R3224
R3983
R3984
1K
10K
10K
R3985 10K
R3136 10K EA10 H21
N2 NU R3986 10K
EA11 E24
CONTINUE C3121 N4 NU R3987 10K
DIGITAL 8 R3202 OPEN EA12 E25
P-ON+12V/+21V Q3106 10K N6 NU R3988 10K
OPEN EA13 G23
R3164 P1 COMP-DET R3989 10K
OPEN EA14 E26
R3147 N7 NU R3990 10K
OPEN EA15 G22
R3189 47K
Q3105 A3 SCL0 NU D24
OPEN
R3163 R3187 47K NU P3
OPEN B4 SDA0
NU P5
CONTINUE AF3 AXI NU T1
DIGITAL 5 C3128 X3101 R3169 NU R2
COMP-DET 10P 24.576MHz OPEN
AE3 AXO NU R4
C3124 R3170 U17 NU NU R3
10P 0
U16 NU NU T3
AD2 NU NU R6
AA6 NU NU M22
N7 NU NU N22

1 R3190 47K
R3191 47K
P2
N5
NU
NU
U20 SDA1
NU
NU
NU
NU
M21
M25
N20
N25
U23 SCL1
NU M23
R3913 47K NU AA11
AA10 SCL0 R3269 10K
R3914 47K NU AF10
AB10 SDA0

DIGITAL MAIN CBA UNIT

M N O P Q R
10-13 PL12.2SCBD3
Digital Main 4 Schematic Diagram [TYPE B]
1 NOTE:
The order of pins shown in this diagram is different from that of actual IC3101.
IC3101 is divided into eight and shown as IC3101 (1/8) ~ IC3101 (8/8) in this Digital Main Schematic Diagram Section.

CONTINUE
DIGITAL 6
P-ON+3.3V
TU3002 TU3001
AL+3.3V OPEN TUNER UNIT
CONTINUE
DIGITAL 7 *1
UART1TX IC3101(4/8)

IF-AGC

IF-AGC
MN2WS0172A

+3.3V

DIF-1
DIF-2

+3.3V

DIF-1
DIF-2
UART1RX R3278 10k DIGITAL SIGNAL PROCESS

GND
SDA
SCL

GND
SDA
SCL
/MAIN MICRO CONTROLLER
R3241 10k

4 (NO CONNECTION)
GND
UARTORX
4
3
CN3101 R3220 OPEN

R3221 OPEN
R3121
R3120
R3214
OPEN
OPEN
100
C22
D21
UART0TX
UARTORX
1 2 3 4 5 6 7 1 2 3 4 5 6 7

UARTOTX 2 C2 UARTORX
P-ON+5V 1 R3213 100
F6 UARTOTX
C3115 R3194 100
TO WIRELESS OPEN C3116 R3101 C3117 R3108 C1 UART1TX
LAN ADAPTOR CN3705 OPEN OPEN OPEN OPEN R3193 100
H6 UART1RX
USB+5V 1 R3217 47K
L3707 OPEN C3004
USB0(-) 2 U25 USB0(-) OPEN
USB0(+) 3 U26 USB0(+)
C3787 R3757 C3786 R3756 C3002 D3001
GND 4 OPEN OPEN OPEN OPEN R3981 R3982 R23 USB0-OD R3010 R3009 OPEN MM5Z5V6B
OPEN OPEN R22 USB0-EN 4.7K 4.7K
L3706 OPEN TO DIGITAL TO DIGITAL
(NO CONNECTION) CN3701 U24 USB1(-) MAIN 5 MAIN 5 C3003 D3002
USB0(+) 1 IC3703 IC3104(5/8) IC3104(5/8) OPEN MM5Z5V6B
R3964 BD2224G-TR V25 USB1(+)
USB0(-) 2 OPEN (HIGH SIDE SWITCH) P23 USB1-OD C3011 L3003 R3048
USB0+5V 3 1 VIN VOUT 5 R21 USB1-EN 0.1 3.3uH 270
GND 4 C3738 C3854 C3855
1 2 GND 220/6.3V OPEN R3755 D1 NU DEMODULATOR AE6 C3026 C3014 C3013 L3004 R3049
GND 5 100 R24 NU /MPEG OPEN 0.1 39P 3.3uH 270
GND 6 3 /EN /OC 4 DECODER AD6
P24 NU NU AB7 C3027
P20 NU OPEN
(USB JACK) CN3704 C3704

3 USB+5V
USB1(-)
USB1(+)
1
2
3
R3828
10K 0.1 N23
R25
P21
NU
NU
NU
IF-AGC AD7
TU-SDA AD9
TU-SCL AE10
R3004
10K
R3006 100
R3007 100
C3010
OPEN
C3005
OPEN
C3008
100P
GND 4 C3741 R3760 C3740 R3759 P26 NU D3907
OPEN OPEN OPEN OPEN C3009 MM5Z5V6B
R20 NU 0.1
V3 NU
IC3701 R3011 47K
R3963 BD2224G-TR U5 NU DMDSCL1 AE8
OPEN R3025 47K D3004
(HIGH SIDE SWITCH) W2 NU DMDSDA1 AD8 OPEN
1 VIN VOUT 5 W1 NU NU AA7
C3739 C3742 C3743 C21 NU
1 2 GND 220/6.3V OPEN R3758 NU AF8
100 R3118 E20 NU
CONTINUE 3 /EN /OC 4 OPEN NU AD14
DIGITAL 8 B21 NU NU AA8
P-ON-H2 B22 NU NU AC7
R3761 C3727 R3109 10K
10K 0.1 AC6 NU NU AB8
CONTINUE L3001
DIGITAL 7 AC4 NU BK1608HS220-T
LCD-P-ON V21 PWR-DETECT NU AD5
C3006 C3007 C3023 C3001 C3021 C3028 D3005
P-ON-H2 NU AD4 OPEN OPEN 10 10 OPEN OPEN MM5Z5V6B
(NO CONNECTION) CN3103 R3021 NU AE5 IC3001
10K
AL+3.3V 1 NU AC19 OPEN
P-ON-H2 2 R3197 100
NU AD26 1 V0 VCC 8

2 CONTINUE
DIGITAL 9
SW-EN
R3196 OPEN
R3921 OPEN
R3146 22
V23 AMP-MUTE
AC23 NU
NU
NU
NU
AA19
AB19
AE26 R3096
22K
R3039
OPEN
C3029
OPEN
R3038
OPEN
R3037
OPEN
2 FB
3 GND
NU 7
NU 6
C3022
OPEN
C3024
OPEN
CONTINUE
DIGITAL 8
LED1 W23 LED1 P-ON+5V
REMOTE 4 NU EN 5
CONTINUE AB25 ARC-MUTE R3036
DIGITAL 9 R3162 22 OPEN
V20 LCD-PON CONTINUE
STM-SCL AA23 NU DIGITAL 7
R3160 100
STM-SDA R3212 100K PROTECT1 AA5 PROTECT1
R3161 100
AMP-MUTE PROTECT3 AE1 PROTECT3
AE2 P-ON-H2 R3910 10K P-ON-H1
R3158 22 NU W22
CONTINUE AC25 STM-EEPROM-WP CONTINUE
DIGITAL 9 DIGITAL 8
PWE DETECT NU U21 PROTECT1
R3165 100 CONTINUE
Y20 VGA-SCL DIGITAL 9
IC3103 R3178 100 LIGHT-SENS AB5 LIGHT-SENS
R3152 R3153 AA20 VGA-SDA
M24C16-WMN6TP 4.7K 4.7K KEY-IN1 AF2 KEY-IN1
(MEMORY) AC23 NU
R3156 39
1 A0 VCC 8 AC5 STM-SCL
R3157 39 Q3104 R3352
R3154 AE4 STM-SDA R3353 OPEN OPEN R3351
OPEN 2 A1 WP 7 0 OPEN
AD25 NU

1 R3155
10K
3 A2
4 VSS
SCL 6
SDA 5
R3151
10K R3148 0
Y19 NU
Y23 REMOTE P-ON-H1 V22
C3127
0.1
R3354
OPEN
Q3103
OPEN R3349
OPEN
R3350
OPEN
CONTINUE
DIGITAL 3
XRST1

CONTINUE
DIGITAL 5
VGA-SDA
VGA-SCL
ARC-MUTE
DIGITAL MAIN CBA UNIT

S T U V W X
10-14 PL12.2SCBD4
Digital Main 5 Schematic Diagram [TYPE B]
1 NOTE:
The order of pins shown in this diagram is different from that of actual IC3101.
IC3101 is divided into eight and shown as IC3101 (1/8) ~ IC3101 (8/8) in this Digital Main Schematic Diagram Section.

CONTINUE
DIGITAL MAIN CBA UNIT *1
DIGITAL 8 IC3101(5/8)
P-ON+5V MN2WS0172A
DIGITAL SIGNAL PROCESS
/MAIN MICRO CONTROLLER
C3200
JK3701 1 AA16 NU
COMPONENT-Y
/VIDEO-IN C3771 R3725 D3702 C3723 R3713 C3219 AB16 NU
39P OPEN OPEN OPEN 75 OPEN Y14 NU

4 COMPONENT
-Pb-IN C3770
39P
R3724
OPEN
D3701
OPEN
C3724
OPEN
R3702
75
AF13 NU
Y13 NU
AC14 NU A/D
CONVERTER
COMPONENT R3289 100
-Pr-IN C3703 R3721 D3704 C3725 R3704 AB17
39P OPEN OPEN OPEN 75 C3196 1 R3283 100
CONTINUE AB14
DIGITAL 3 C3197 1 R3284 100
COMP-DET AA15
C3198 1 R3285 100
AA14
R3015 C3193 1 R3280 100 TO DIGITAL
R3019 10K C3016 Y18
100 1 C3194 1 R3281 100 MAIN 2
AA17 SW IC3104(2/8)
Q3001 R3016 C3195 1 R3282 100
C3706 R3017 2SC4081UBTLQ Y17
JK3706 1 220 10K
DIGITAL (BUFFER) R3843 R3841 R3840 TO DIGITAL
AUDIO OUT C3705 C3019 75 75 75 MAIN 3
(COAXIAL) 100P R3018 R3020
110 OPEN 33P DIGITAL IC3104(3/8)
R3287 100
AB9 VGA-HSYNC SIGNAL
R3286 100 PROCESS
AUDIO(L)-IN AA9 VGA-VSYNC TO DIGITAL
C3710 R3708 D3703 C3721

OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
56P 91K OPEN OPEN C3192 OPEN MAIN 7
AC16 NU IC3104(7/8)
AF7 NU

C3220
C3218
C3217
C3216
C3215
C3214
AUDIO(R)-IN C3711 R3709 C3722 R3308 TO DIGITAL
D3707 0
56P 91K OPEN OPEN MAIN 4
IC3104(4/8)

3 JK3713
PC-RGB-IN R3288 39
R3303 39
C3199 1
C3209 1
AB15
AA18
R3304 39 C3210 1
1 6 11 R3835 R3836 R3848 AC17
OPEN OPEN OPEN
SCALER
2 7 12

3 8 13

4 9 14 TO DIGITAL
SPDIF MAIN 1
AD10 IC3104(1/8)
C3207 1 R3297 110K
5 10 15 AD13
C3208 1 R3298 110K
D3711 1SS400

AE13
R3839 4.7K
R3838 4.7K

OPEN
OPEN

OPEN
OPEN
OPEN
OPEN
OPEN
10K
10K

AB13 NU
AA13 NU
R3847
R3846
R3831
R3830

D3717
D3716
D3715
D3714
D3713

AA12 NU TO DIGITAL
MAIN 7
AB12 NU IC3104(7/8)
AE12 NU AUDIO
I/F
D3712 C3017 C3018 AD11 NU

2 CONTINUE
DIGITAL 4
VGA-SDA
1SS400 OPEN 0.01
AE11 NU
AF11 NU
R5 NU
TO DIGITAL
MAIN 4
IC3104(4/8)
VGA-SCL R7 NU
ARC-MUTE U1 NU
T2 NU
CONTINUE R3307 10K
DIGITAL 9 AE9 NU
AMP(L)-OUT AC10
AMP(R)-OUT AB11
V7 NU
CONTINUE
DIGITAL 6 AA4 NU
P-ON+3.3V AB4 NU
C3015 C3020 Q3004 Y6 NU
OPEN 0.01 R3013 2SA1576UBTLQ
220 Q3002 L26 NU
(MUTE) 2SC4081UBTLQ
(BUFFER) K24 NU
R3005 R3991 L22 NU
220 47K
R3012 K26 NU
220 Q3003 R3008
2SA1576UBTLQ R3001 220 L21 NU
2K R3014 R3125 10K
(BUFFER) 56 K25 BACKLIGHT-SW
R3003 R3919 10K
10K J24 NU

1 CONTINUE
DIGITAL 7
BACKLIGHT-SW
ARC-OUT
R3002 C3025
C3012
1 K22 NU
J25 NU
K21 NU
10K OPEN H24 NU
P25 NU
T20 NU
T25 NU

Y Z AA AB AC AD
10-15 PL12.2SCBD5
Digital Main 6 Schematic Diagram [TYPE B]
1 NOTE:
The order of pins shown in this diagram is different from that of actual IC3101.
IC3101 is divided into eight and shown as IC3101 (1/8) ~ IC3101 (8/8) in this Digital Main Schematic Diagram Section.

*1
IC3101(6/8)
MN2WS0172A
DIGITAL SIGNAL PROCESS
DIGITAL MAIN CBA UNIT
CONTINUE /MAIN MICRO CONTROLLER
DIGITAL 1 BC3101
0
P-ON+3.3V T10 VDD33 BC3104
C3167 C3159 C3171 C3173 C3174 T11 VDD33 0
OPEN OPEN OPEN L3106 1 0.1 VDD12 M15
BEAD VDD12 M16 C3136 C3137 C3138 C3139 C3140 C3141 BC3103
R10 AVDDPLLD1-33 10 OPEN 0.1 0.1 0.1 0.1 OPEN
C3156 VDD12 N11

4 CONTINUE
DIGITAL 4
P-ON+3.3V
AL+3.3V
L3117
BEAD
0.1

C3155
0.1
R11 AVDDPLLA-33

P16 AVDDPLLD2-33
VDD12
VDD12
VDD12
N13
N14
N15
VDD12 P10
VDD12 P11
L3119 VDD12 T13
BEAD VDD12 U12
CONTINUE M12 DPAVDD33
DIGITAL 3 C3176 BC3102
0.1 0
AL+3.3V L3101 VDDR M13
BEAD C3142 C3143 C3144 C3151
P-ON+3.3V F4 LVVDD33 VDDR M14 10 0.1 0.1 OPEN
C3135 C3134 VDDR N12
CONTINUE OPEN 0.1
DIGITAL 5 L3120 VDDR K11
BEAD
P-ON+3.3V P17 AVDDAPUSB33-0 VDDR K12
C3158 C3133
OPEN 0.1 VDDR L11
R17 AVDDAPUSB33-1 VDDR L12
L3102
BEAD
L3123 VDDRA M11
BEAD R3181
Y11 AVDDEVE33 4.7
C3170 C3145 L3107
CONTINUE 0.1 0.47 BEAD
DIGITAL 7 L3121 LVVDD12 E2
BEAD

3 P-ON+3.3V
AL+3.3V
L3108
BEAD
R3204
510
C3175
1
AD22 AVDDH33

Y10 AVDDADA33 VDDUSB12 N17


C3157
0.1
L3109
BEAD
C3164 C3163 C3162 C3166 C3165
CONTINUE 10 OPEN 0.1 10 0.1
DIGITAL 9 L3115
0
AL+3.3V Y12 AVDDHP33
C3114
CONTINUE 0.1 VDDIO15-1 F7
DIGITAL 10 L3110
0 VDDIO15-2 G8 C3146 C3147 C3148 C3149
P-ON+3.3V L10 VDD25TCON 1 1 0.1 0.1
C3105 VDDIO15-3 G15
R3205 0.1 VDDIO15-4 G16
0
M17 VDD5 L3124
C3104 BEAD
0.1 VDDIOCK15 H8
CONTINUE C3224
DIGITAL 2 L3103 1
BEAD
VCC+1.5V AF5 VDD33STM L3105
C3150 0
0.1 VDD12STM AF4
C3153
Y7 STMADAVDD33 1
C3152
L3114 0.1
BEAD
T22 VDDSD18-33

2 CONTINUE
DIGITAL 8
L3111
0
C3172
0.1

C3161
AD23 AVDDH18 VREFHSIF AC9
C3180
C3182 1

P-ON+3.3V L3112 0.1 1 C3181 1


VCC+1.5V BEAD VREFLSIF AC8
U14 VDDAVAD18
AL+3.3V C3160 C3183 1
0.1 VREF1V5 AD12
AL+1.25V L3113 C3185 0.01
BEAD
VCC+1.8V Y8 AVDDSIF18
C3113 C3187 1
VCC+1.25V 0.1 VREFH0 Y16
L3104 C3184
BEAD 1 C3186 1
Y9 AVDDV33 VREFL0 Y15
C3103
0.1 R3211 6.2K
USB0RREF T26
USB1RREF T24 R3210 6.2K
L3116
OPEN
AE7 VCOMP

NU *A
FPEN R12
TESTSEL T12 *A:D18~D20,E13.E18,F13,J23,K23,L23,N3,N21,P4,
P6,P22,R16,T4,T16,U4,U22,AC12,AC13,AC15,

1 GND *B
AC18,AD16,AD17,AD19
*B:A1,A26,D12,D15,E3,E5,E8,E12,E16,F5,F9,G5,
G7,H5,H7,K10,K13~K17,L13~L17,N16,P12~P15,
R13~R15,T14,T15,T17,U10,U11,U13,U15,W7,
AC11,AC21,AD3,AD20,AF1,AF26

AE AF AG AH AI AJ
10-16 PL12.2SCBD6
Digital Main 7 Schematic Diagram [TYPE B]
1 NOTE:
The order of pins shown in this diagram is different from that of actual IC3101.
IC3101 is divided into eight and shown as IC3101 (1/8) ~ IC3101 (8/8) in this Digital Main Schematic Diagram Section.

DIGITAL MAIN CBA UNIT


CONTINUE
DIGITAL 4 CONTINUE
LCD-PON DIGITAL 5
P-ON-H2 BACKLIGHT-SW
ARC-OUT
*1
CONTINUE IC3101(7/8)
DIGITAL 1 MN2WS0172A

4 VCOM-PWM
LCD-PON
BACKLIGHT-ADJ
OE2
DIGITAL SIGNAL PROCESS
/MAIN MICRO CONTROLLER

JK3717
HDMI-
CONNECTOR-1
PROTECT3 AE17 1 DATA2(+)
AF17 2 TMDS DATA2 SHIELD
AE16 3 DATA2(-)
AF16 4 DATA1(+)
(NO CONNECTION) CN3602 R3666 OPEN AD15 5 TMDS DATA1 SHIELD
BACKLIGHT-SW 1 AE15 6 DATA1(-)
R3660 OPEN R3665 OPEN
BACKLIGHT-ADJ(DC)
2 AE14 7 DATA0(+)
R3667 OPEN
P-ON-H1 3 AF14 8 TMDS DATA0 SHIELD
GND 4 C3683 C3678 C3677 C3679 C3690
OPEN OPEN OPEN R3663 OPEN OPEN OPEN AD21 9 DATA0(-)
BACKLIGHT-ADJ(PWM)
5 AE21 10 CLOCK(+)
AL+5V 6 AE20 11 TMDS CLOCK SHIELD
GND 7 C3687 C3686
OPEN OPEN HDMI AF20 12 CLOCK(-)
GND 8 I/F
AE19 13 HDMI-CEC
GND 9 AF19 14 ARC
D3616 OPEN
GND 10 AD18 15 HDMI-CLOCK
R3664 OPEN R3668 OPEN
P-ON+12V 11 AE18 16 HDMI-DATA
P-ON+12V 12 C3692 C3691 R3659 R3787 R3788 C3769 C3768
OPEN OPEN OPEN AE25 R3791 47K 47K OPEN OPEN 17 GND
P-ON+12V 13 10K
AF25 18 +5V
AMP+24V 14 AE24 C3767 R3960 R3786 D3721 19 HOT PLUG DETECT
C3688 C3685 C3689 0.1 47K R3706 1K OPEN
OPEN OPEN OPEN AF24 10K
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN

3 AE23
AF23
R3705
10K Q3701 R3790
2SC4081UBTLQ OPEN
(SWITCHING)
C3766
OPEN
HDMI-
C3646
R3955
C3648
C3647
C3649
C3656
C3658
C3657
C3659

TO POWER SUPPLY AE22 JK3716 CONNECTOR-3


CBA CN631 CN3601 R3601 OPEN 1 DATA2(+)
VCOM-PWM(NU) 1 AF22
R3620 100 2 TMDS DATA2 SHIELD
BACKLIGHT-SW 2 3 DATA2(-)
R3603 100
BACKLIGHT-ADJ 3 4 DATA1(+)
PROTECT3 4 AUDIO VIDEO 5 TMDS DATA1 SHIELD
R3645 OPEN DECODER DECODER
PROTECT1 5 6 DATA1(-)
R3629 OPEN
P-ON-H1 6 7 DATA0(+)
R3647 100
P-ON-H2 7 8 TMDS DATA0 SHIELD
RESET 8 TO DIGITAL TO DIGITAL 9 DATA0(-)
R3636 OPEN MAIN 5 MAIN 5
OE2(NU) 9 IC3101(5/8) IC3101(5/8) 10 CLOCK(+)
GND 10 C3660 R3956 R3179 100
OPEN OPEN HDMI-CEC AA21 11 TMDS CLOCK SHIELD
AL+3.3V 11 STMCECPUL AB18 12 CLOCK(-)
GND 12 C3652 C3651 R3992 39
OPEN OPEN HDMI0-SCL AA22 13 HDMI-CEC
AMP+24V 13 R3993 39
HDMI0-SDA AA24 14 NU
AMP+24V 14 C3653 C3650 C3655 R3994 39
OPEN OPEN OPEN R3972 R3973 HDMI1-SCL W21 15 HDMI-CLOCK
GND 15 OPEN OPEN R3995 39
HDMI1-SDA Y21 16 HDMI-DATA
P-ON+21V 16 R3996 39 R3781 R3780 C3760 C3761
HDMI2-SCL AB22 R3784 47K 47K OPEN OPEN 17 GND
P-ON+21V 17 C3675 C3676 C3632 R3997 39 10K
OPEN OPEN OPEN HDMI2-SDA AB23 18 +5V
GND 18 C3759 R3785 R3779 D3720 19 HOT PLUG DETECT
0.1 47K R3710 1K OPEN
GND 19 10K
R3628
GND 20 100 HDMI0-HPD AB21 R3707 R3783 C3758
10K Q3702

2 GND
P-ON+21V
P-ON+21V
21
22
23
Q3611
OPEN
HDMI1-HPD AD24
HDMI2-HPD AC24

HDMIO-5V AB20
2SC4081UBTLQ OPEN
(SWITCHING)
OPEN
JK3715
1
HDMI-
CONNECTOR-2
DATA2(+)
R3627 2 TMDS DATA2 SHIELD
CONTINUE OPEN HDMI1-5V AC22
DIGITAL 4 3 DATA2(-)
PROTECT1 HDMI2-5V AC20 4 DATA1(+)
R3863
PROTECT3 27K 5 TMDS DATA1 SHIELD
P-ON-H1 R3623 D3722 6 DATA1(-)
R3694 OPEN 1SS400
CONTINUE OPEN R3865 7 DATA0(+)
DIGITAL 8 Q3612 22
P-ON+12/+21V OPEN 8 TMDS DATA0 SHIELD
C3696 R3637
AL+5.3V OPEN OPEN 9 DATA0(-)
CONTINUE HDMI-UART-CTRL AB26 10 CLOCK(+)
DIGITAL 9 11 TMDS CLOCK SHIELD
LCD-PON 12 CLOCK(-)
CONTINUE 13 HDMI-CEC
DIGITAL 3 R3673
RESET R3671 10K R3600 R3730 14 NU
OPEN OPEN 0
CONTINUE R3649 15 HDMI-CLOCK
DIGITAL 9 R3672 R3669 10K 16 HDMI-DATA
AMP+24V OPEN OPEN Q3706 R3714 C3751 C3752
OPEN 10K Q3704 R3777 R3773 R3774 OPEN OPEN 17 GND
CONTINUE R3675 R3648 2SC4081UBTLQ 10K 47K 47K
DIGITAL 8 R3674 Q3621 0 OPEN 18 HDMI+5V
OPEN 2SC4081UBTLQ R3720 (SWITCHING) C3750 R3778 D3719
DC-DC-EN Q3622 (SWITCHING) 33K 0.1 47K R3712 R3775 OPEN 19 HOT-PLUG-DETECT
OPEN R3670 R3684 R3771 10K 1K
OPEN Q3620 OPEN OPEN
2SC4081UBTLQ

1 CONTINUE
DIGITAL 4
UART1TX
C3694
OPEN
(SWITCHING) C3600
OPEN R3772
OPEN
R3711
10K Q3703 R3776
2SC4081UBTLQ 100K
(SWITCHING)
C3749
OPEN

UART1RX R3717
1K
CONTINUE
DIGITAL 6 R3715
Q3705 10K
P-ON+3.3V 2SC4081UBTLQ
AL+3.3V (SWITCHING) R3716
33K

AK AL AM AN AO AP
10-17 PL12.2SCBD7
Digital Main 8 Schematic Diagram [TYPE B]

CONTINUE
DIGITAL 7 DIGITAL MAIN CBA UNIT
DC-DC-EN
D3611 R3682 R3607
MM5Z15B 10K 0
Q3601 R3683 C3702 R3904 C3604
R3695 2SA1576UBTLQ 100K 1 OPEN OPEN
OPEN (SWITCHING)
CONTINUE R3608
DIGITAL 4 10K
P-ON-H2 R3609

4 R3610
4.7K

C3626
1
D3614
1SS400
R3611
OPEN
4.7K
Q3602
2SC4081UBTLQ
(SWITCHING)
IC3601
MP2303ADN
(+3.3V REG.)
1 BS SS 8
C3612 C3607
0.01 0.047
2 VIN EN 7
IC3606 C3693 C3609 C3616 C3610
MP2303ADN OPEN 4.7 4.7 OPEN 3 SW COMP 6
(+1.5V REG.) R3606
C3661 4 GND FB 5 11K
0.047 R3677
1 BS SS 8 47K R3604 C3611
C3667 R3631 R3687 15K 0.015
0.01 10K OPEN L3604 R3605 D3607
CONTINUE 2 VIN EN 7 22uH 100 OPEN
DIGITAL 1 C3662 C3673 C3674 C3664 R3908 C3665 C3967
P-ON+12V/+21V OPEN 4.7 4.7 OPEN 3 SW COMP 6 OPEN OPEN OPEN C3615 C3614 C3603 C3606 C3608 C3613 R3643 D3613
R3635 OPEN 10 10 OPEN 10 OPEN OPEN OPEN R3655
P-ON+5V 4 GND FB 5 4.7K OPEN Q3604
R3679 R3633 C3666 OPEN
CONTINUE 9.1K 11K 0.015 R3656
DIGITAL 4 L3603 R3634 BC3106 OPEN
P-ON+5V 22uH 560 0
R3685 C3668 C3669 C3671 C3670 C3672 R3642 D3908 R3095
CONTINUE OPEN 470/4V 10 10 10 10 OPEN OPEN 10K
DIGITAL 5
P-ON+5V C3968
OPEN R3657

3 CONTINUE
DIGITAL 7
P-ON+12V/+21V
AL+5.3V
OPEN
R3658
OPEN
Q3605
OPEN

CONTINUE
DIGITAL 9
P-ON+5V
C3663 C3624 C3625 C3631
OPEN OPEN 4.7 4.7
IC3607
MP2303ADN
R3622 (+5V REG.) R3618
0 C3617 10K
0.047
1 BS SS 8
R3626 C3630 IC3604 C3620
OPEN OPEN 0.01
MP2303ADN 2 VIN EN 7
(+1.25V REG.) C3601 R3909 C3618
0.015 3 SW COMP 6 OPEN OPEN
CONTINUE 1 BS SS 8 R3614
DIGITAL 3 C3639 6.2K
0.01 R3686 4 GND FB 5
P-ON+12V/+21V 2 VIN EN 7 OPEN R3617 C3619
C3605 C3645 C3654 C3629 R3678 10K 4700P
OPEN 4.7 4.7 OPEN 3 SW COMP 6 C3966 47K
R3625 OPEN
4 GND FB 5 4.7K L3605 R3616
22uH 6.2K

2 R3689
OPEN L3601
10uH
R3676
5.1K
R3624
560
R3613
10K
C3638
0.015
C3622
OPEN
C3621
10
C3628
10
C3623
10

C3969 C3640 C3641 C3643 C3642 C3644 R3640 D3612


OPEN OPEN 10 10 OPEN OPEN OPEN OPEN D3610 CONTINUE
OPEN DIGITAL 4
PROTECT1
D3606
IC3602 R3661 1SS400
AP2126K-ADJTRG1 OPEN Q3606
(+1.25V REG.) OPEN
R3662 (SWITCHING) C3627 D3615 R3644 R3653
1 VIN VOUT 5 OPEN OPEN CRY68 OPEN OPEN Q3603
C3637 C3971 R3681 D3604 C3973 C3633 R3638 OPEN
2.2 OPEN OPEN MM5Z3V6B 2 GND R3690 1 OPEN OPEN R3654
0 OPEN
3 CE ADJ 4
R3619 R3602 C3602 R3621
100 2.2K 10 OPEN IC3605
IC3603 D3725 BD00IC0WEFJ
C3699 AP2121AK-3.3TRE1 1SS400 (+1.8V REG.) CONTINUE
OPEN (+3.3V REG.) DIGITAL 6
1 V0 VCC 8 P-ON+3.3V
1 VIN VOUT 5 R3688 C3680 C3682 R3680 R3650 C3681 C3684 VCC+1.5V
R3615 D3605 C3635 C3972 C3974 C3636 R3639 100 220/6.3V 10 OPEN 2.2K 2 FB NU 7 OPEN 10
OPEN OPEN OPEN OPEN 2 GND R3691 1 OPEN OPEN AL+3.3V
OPEN
C3695 R3651

1 C3634
OPEN
R3612
100K
3 CE ADJ 4
R3692
OPEN
OPEN 12K
R3652
11K
3 GND
4 NU
NU 6
EN 5
C3697
OPEN
C3698
OPEN
AL+1.25V
VCC+1.8V
VCC+1.25V

Q3608
R3632 2SA1576UBTLQ R3641
10K (SWITCHING) 10K
R3646
22K
Q3609 C3963
2SC4081UBTLQ 0.47
(SWITCHING)

AQ AR AS AT AU AV
10-18 PL12.2SCBD8
Digital Main 9 Schematic Diagram [TYPE B]

CONTINUE
DIGITAL 6
AL+3.3V DIGITAL MAIN CBA UNIT
CONTINUE
DIGITAL 8
P-ON+5V

R3200 Q3108 R3206 R3215


CONTINUE OPEN
DIGITAL 4 OPEN OPEN OPEN

4 SW-EN
LED1
REMOTE
R3207
OPEN
R3102
R3209 1K
R3188 OPEN
OPEN
TO FUNCTION R3107
CBA CN4001 CN3105 Q3107 100
SDA 1 OPEN
SCL 2
GND 3
KEY-IN1 4 C3109
C3107 OPEN
REMOTE 5 100P
LED1 6 R3323
OPEN Q3102
LIGHT 7 OPEN
R3117 10 C3110 C3112 R3119 C3108
P-ON+5V 8 100P OPEN OPEN OPEN
AL+3.3V 9
C3975 R3201 Q3101 R3106 CONTINUE
OPEN 0 2SC4081UBTLQ OPEN R3159 DIGITAL 4
(LED DRIVE) OPEN
C3111 LIGHT-SENS
OPEN R3103 R3104 C3106 R3182
OPEN OPEN OPEN 10K KEY-IN1
C3122 OPEN R3105
R3150 100 R3149

3 C3123 OPEN 10K


D3101
OPEN
C3130
OPEN
0

R3110 R3114 R3827


CONTINUE 33 33 10K
DIGITAL 4
STM-SCL
STM-SDA
AMP-MUTE

CONTINUE
DIGITAL 5 R3998
2.7K
AMP(L)-OUT CONTINUE
C3964 C3808 DIGITAL 7
AMP(R)-OUT 470P 1 LCD-PON
C3818 10 C3819 10
C3817 4.7 R3814 27K CONTINUE
DIGITAL 3
30 29 28 27 26 25 24 23 22 21 PWR-DETECT

2
VREFF
PROT

AVCC
ROSC
GND
GND
GND
GND
GND
NU

R3815 CONTINUE
10K R3999 R3818 C3820 DIGITAL 4
2.7K OPEN 10
31 GND CBIAS 20 R3851 PWR-DETECT
C3809 OPEN
1
32 19
C3965 R3813
470P OPEN Q3803 R3802 C3802
33 18 2SA1576UBTLQ 180 OPEN
Q3801 R3812 R3822 (SWITCHING)
0 10K R3861
2SC4081UBTLQ 34 CONTROL 17 OPEN
(SWITCHING) R3806 R3817 LOGIC R3807 C3833 R3823 JK3801
47K 33K C3821 OPEN 0.1 100K R3821
0.1 35 GND GND 16 22K R3805 R3850 HEADPHONE
R3816 22K OPEN C3804 R3801 JACK
10K 100/35V 180
CONTINUE 36 GND GND 15 R3820 Q3802
DIGITAL 7 10K 2SC4081UBTLQ C3801
AMP+24V 37 VDD PWM PWM VDD 14 (SWITCHING) C3823 OPEN
GENE. GENE. 100/35V
C3827 C3816 R3819
100/35V 0.1 38 VDD VDD 13 22K C3832
L3801 100/35V R3849 L3803
33uH OPEN OPEN
39 12
D3801 R3804 C3811 C3825 C3830 R3833
40 11 MM5Z33B OPEN 0.1 0.1 OPEN OPEN
C3806 C3810
DVDD1

OPEN 100/35V R3825


GND
HB2

GND
GND
GND
GND
GND
HB1
GND

IC3801 OPEN
R2A15122FP 1 2 3 4 5 6 7 8 9 10 L3802 C3822 R3864
-W00R 33uH 100/35V OPEN
(AUDIO AMP)

1 R3808
0
R3809
OPEN
C3814
0.1
C3828
10
R3834
0
C3813
0.1 D3802
MM5Z33B R3803
OPEN
C3805
OPEN
C3812
0.1
C3824
0.1
C3803
100/35V

R3824
OPEN
C3807
OPEN
R3832
OPEN
CN3801
1 SP(L)
SP3801
SPEAKER
L-CH
R3810 2 GND
OPEN R3800
OPEN Q3804 C3834 R3826 3 GND
C3829 C3815 C3826 C3831 OPEN OPEN OPEN
R3811 R3799 100/35V 0.1 100/35V OPEN 4 SP(R) SP3802
OPEN OPEN
SPEAKER
R-CH

AW AX AY AZ BA BB
10-19 PL12.2SCBD9
Digital Main 10 Schematic Diagram [TYPE B]
1 NOTE:
The order of pins shown in this diagram is different from that of actual IC3101.
IC3101 is divided into eight and shown as IC3101 (1/8) ~ IC3101 (8/8) in this Digital Main Schematic Diagram Section.

DIGITAL MAIN CBA UNIT

R3875 22

4 C3980
OPEN
R3871 22
R3738
4.7K
R3727 OPEN
C3976 R3739
OPEN OPEN
R3872 22 R3966 OPEN
C3977 R3740
OPEN OPEN
R3873 22 R3837 OPEN

*1 C3978 R3967
OPEN OPEN
IC3101(8/8) R3874 22 R3726 OPEN
MN2WS0172A
DIGITAL SIGNAL PROCESS C3979 R3741
/MAIN MICRO CONTROLLER OPEN 4.7K
R3733 22
C3756 R3745
MII_CRS T7 OPEN OPEN R3737
R3732 22 OPEN
MII-COL Y1
R3859 0 C3709 C3755
MII-RXCLK U7 10P OPEN
RMII-RXD0 AA3 C3708
RMII-RXD1 W5 10P

3 RMII-RXD2
RMII-RXD3
RMII-RXDV
W4
AB2
W3
24 23 22 21 20 19 18 17 16 15 14 13

VDD
GND

VDD
RMII-RXER AC1
25 NU 12
MII/RMII CONTROLLER R3728
26 NU 11 0
R3767
OPEN
27 PMEB 10
R3729 R3766
28 VDD10 NU 9 4.7K OPEN
29 PHYRSTB PARALLE SERIAL TO NU 8 R3765
TO SERIAL PARALLEL OPEN
30 GND 7
R3764
R3723 1K OPEN
31 VDD 6 CN3706 (ETHERNET JACK)
R3829 0 R3718 4.7K 7 NU
MII-TXCLK AA2 32 5
R3842 22 RECEIVER 8 GND
RMII-TXD0 Y3 R3856 22
R3844 22 33 GND 4 6 RD(-)
RMII-TXD1 V6 C3982
R3845 22 OPEN R3736 4.7K R3749 R3748 5 RCT
RMII-TXD2 Y4 34 NU NU 3 OPEN OPEN
R3852 22 4 RD(+)
RMII-TXD3 Y2 R3735 4.7K TRANSMITTER
R3853 22 35 NU 2 3 TD(-)

2 RMII-TXEN Y5 R3857

VDD10-OUT
R3854 22 22 2 TCT
MII-MDC W6 36 1
R3855 22 1 TD(+)

AUDIO
MII-MDIO AC2

RSET

-OUT
VDD

VDD

GND
C3984 R3722 R3747 R3750

XI
XO
NU
NU
MII-MDIO-INTL AB3 OPEN OPEN OPEN OPEN C3744 C3701
R3877 22 IC3902 0.01 0.01
HUB-RESET AD1 37 38 39 40 41 42 43 44 45 46 47 48 RTL8201FL-VB-CG
WAKEUP V5 (ETHERNET I/F)
C3737
WUC AB1 0.1
R3754
R3878 R3879 R3860 C3993 2.49K
OPEN OPEN 10K OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
C3992
C3985
C3986
C3987
C3989
C3990
C3991

C3732 R3701
0.1 OPEN C3731 C3730 C3736 C3733 C3999
0.1 0.1 0.1 0.1 0.1
R3858
22 R3703
X3701 0
R3876 25MHz
22
C3983 C3981 C3735 C3734
CONTINUE BC3704 OPEN OPEN R3719 R3954 15P
DIGITAL 6 4.7K 4.7K 12P
BK1608HS220-T
P-ON+3.3V
C3753
OPEN

BC BD BE BF BG BH
10-20 PL12.2SCBD10
Power Supply CBA Top View
Because a hot chassis ground is present in the power supply
CAUTION ! circuit, an isolation transformer must be used when repairing.
Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. CAUTION ! : For continued protection against risk of fire, Also, in order to have the ability to increase the input slowly,
If Main Fuse (F601) is blown , check to see that all components in the power supply replace only with same type 4A, 125V fuse. when troubleshooting this type of power supply circuit,
circuit are not defective before you connect the AC plug to the AC power supply. 4A 125V ATTENTION : Utiliser un fusible de rechange de même type de 4A, 125V. a variable isolation transformer is required.
Otherwise it may cause some components in the power supply circuit to fail.
NOTE:
The voltage for parts in hot circuit is measured using
hot GND as a common terminal.

A 1.ILED4 2 CN1001 6
D402B B J120
D401 C D E
2.ILED3

GND
PROTECT3

PROTECT3

C653
3.NC

C651
GND
J130

J119
J121

C655
4.VLED
5.NC 1

ALL+5-CONT.
6.ILED1 7 BL-ADJ

J109
GND
7.ILED2

PROTECT1
J111

C663

J110
R650

J117

PROTECT1

C650
C1011 J122

J116

CN631
J113

P-ON-H2+
GND D652

J118
P-ON+21V J105

D654

2
J106
GND

D651

for Z-SoC
D405

C650

GND
P-ON+21V

ALL+3.3V forR-SoC
ALL+5.3V forP-SoC
3

JS631
J123
R678

GND

D650
D406

J132
GND
D1005B

ALL+5V-CONT.
C7A3 A3
J131

P-ON-H2+
C1001

C654
C1010 J115
VCC

J103
JS632
GND
C652

J108
GND

J125
GND
J133
J134
GND

R670

RESET
J104
D657B
R671 J107

23
D1002
P-ON+21V

C656
BC1002

D653

J102
P-ON-H2
J129
GND C662 R672 1.GND
L1001

J112
GND
2.BL-SW
R1003

3.BL-ADJ

D662
J127 J128
GND D661B R657
COLD 4.P3
5.P1

Q656
J124
GND

6.GND
P-ON+21V 7.P-ON-H2
8.RESET
D663 9.GND

C602
T601
J126 10.GND
P-ON+21V R655 11.ALL+3.3V
C1007 No.1 /ALL+5.3V

D660
12.GND
R654 13.AMP+24V

BA21F0F0102 2 HOT 14.AMP+24V


15.GND

J114

GND

J101

GND
16.17.21V
18.19.20.21.GND
22.23.21V
2

D658
C601

IC601

C603
SA603

BC601
C606
D610
C617
L602
C614

R613

J609
GND
Q601
L601 J605 R501
R607
GND

BC604
D603

GND
D602

D605B R606
D609

J606
R608
R612 C615
D604

Q602
JS601

R611
GT601

JS602

J607
GND

D607
GT602

D608
BC603
D601
SA602

J608
GND
1

C604

R601

RISK OF FIRE-
REPLACE FUSE AS MARKED
SA601

R602
TOOL NO.
1 2 3 4 5 6 7 8 9 10 NEUTRAL
C616
LIVE
CN601

F601
4A/125V
C605

FH602 FH601 BC602

10-21 BA21F0F01022
Power Supply CBA Bottom View
Because a hot chassis ground is present in the power supply
CAUTION ! circuit, an isolation transformer must be used when repairing.
Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. CAUTION ! : For continued protection against risk of fire, Also, in order to have the ability to increase the input slowly,
If Main Fuse (F601) is blown , check to see that all components in the power supply replace only with same type 4A, 125V fuse. when troubleshooting this type of power supply circuit,
circuit are not defective before you connect the AC plug to the AC power supply. 4A 125V ATTENTION : Utiliser un fusible de rechange de même type de 4A, 125V. a variable isolation transformer is required.
Otherwise it may cause some components in the power supply circuit to fail.
NOTE:
The voltage for parts in hot circuit is measured using
hot GND as a common terminal.

E C630 C631
C632 D C D401
J120
B R402
D402B
6 CN1001 2 1.ILED4
A

PROTECT3
2.ILED3

GND

C653

C651
PROTECT3

J119

J130
3.NC

ALL+5-CONT.

GND
D402

C655
J121 4.VLED
1 5.NC
BL-ADJ 7
J109
6.ILED1
PROTECT1
R401
GND

C633 7.ILED2
D401A

J111
D652A R1011 R1501

C663

PROTECT1
J110

J117
C650
R650 C1015 R1010 R1503 C1012
J122 C1011

J116
R1020

P-ON-H2+
CN631

D405A R1502 R1021 C1018


J113

J118
J105 P-ON+21V D652 GND 1 24 R1012

D654
R1504
1

C637 D406A
J106

C1016

ALL+3.3V forR-SoC

D651
2

for Z-SoC
ALL+5.3V forP-SoC
GND D654A

P-ON+21V

C650
GND

D405 R1019

3
R650A

JS631
C1017

J123
D650
C1013

GND
C638 R678 R1006
D406 D1005 C1021
J132
ALL+5V-CONT.

GND

C1008
D1005B R1015
P-ON-H2+

J131
C654

VCC
J115 R1007 C1001
J103

C1010
JS632

R670A R669
D657 D656 GND 12 13 C1004
J108

R676 Q655 C652 R1009 C1014 IC1001


R678A
R668

J125
GND C1002

GND
R1008

Q654
R675

J134
J133

GND
C1022
RESET

R673 C1009
J104

R670
C664 D657B R651 R667
J107 R671 R1018 D102A C1003 D1004
R666 C1019
23

R672A R652 D1002


P-ON+21V
C656

C639 R653 R403 C1020


P-ON-H2

D653

BC1002
J102

J129

L1001
1.GND R672 R671A Q653 C662 GND
J112
GND

R1003
2.BL-SW
C665
D662

3.BL-ADJ C658 R665 R664 R1017 C1005


4.P3 Q652 J128 R1016 J127 R1001
Q650 R657
Q656

D661B

J124
5.P1 GND

GND
6.GND R681 R1014
D1001
7.P-ON-H2 P-ON+21V
8.RESET R659 R663
9.GND D663
C602

R682
T601

10.GND R654A R660 D661 J126 C1006


11.ALL+3.3V R662 R657A R655 P-ON+21V

D660
/ALL+5.3V R680 C1007
12.GND C636
13.AMP+24V R654 C660
14.AMP+24V D663A C661 R661
BA21F0F0102 2 R1002
R1005 Q1001 R1004

J114
GND
J101

15.GND R655A
GND

16.17.21V R677 C659


18.19.20.21.GND

2
22.23.21V R658
D658

C601
D658A

IC601
C603
SA603
C635
BC601

C606

R603 D610 C610


C617
L602

C614
R614 R607A R613
J609
GND

D610A
Q601

D609A D605
R501 R604 D608A C609 R613A J605 L601
R607
BC604

D603
GND
GND

R608A

D602
R606 D605B R612A
J606

D609
R605
R610 C608 R606A R608
C615 C607 R612

D604
Q501
Q602

JS601
R611

GT601
D607A

JS602
J607
GND
D607

GT602
D608

D501

D601
BC603
R502

SA602
J608
GND

1
C604
R601
D502
C501

SA601
R602

C616
CN601

F601
4A/125V
C605

BC602 FH601 FH602

10-22 BA21F0F01022
Function CBA Top View

R4011 R4012 R4014 C4055

TP4055

D4052
C4006
NO.12

R4056
TP4054
R4063 TP4061

C4058
R4061 R4054

TP4059
R4010
R4052

R4053
R4002 R4013
C4002 TP4062 TP4060

TP4058
R4004 R4062 C4053 C4054
IC4001

C4052
R4055
R4059
R4006
C4001 A30C5 C7A3 A3 CN4001 R4058 D4053
R4007

TP4057
R4051

C4057
P R4005 D4051
b
R4009 R4003
R4001
POWER CH + CH - SOURCE MENU VOL + VOL - C4051
R4057
R4008 TP4056 C4056

Function CBA Bottom View

R4021
D4002
BA21F5G0203 2

D4003
D4004
R4022
RS4051 C4003
D4001

R4017
IC4051

P
b

10-23 BA21F5G02032
SP3801 SP3802
SPEAKER SPEAKER
L-CH R-CH
[TYPE A]

CL3801

1 4
CN3101 CN4001
COMPONENT CN3801
-Y/VIDEO-IN 1 9
CL3101
FUNCTION CBA
COMPONENT
-Pb-IN 9 1
AC CORD

COMPONENT
-Pr-IN

TUNER UNIT
AUDIO(L)-IN

REAR 1 2
AUDIO(R)-IN CN601

DIGITAL
AUDIO-OUT
(COAXIAL) CN3701 CN631

11-1
1 1
CL3701
HDMI- DIGITAL MAIN CBA UNIT POWER SUPPLY CBA
CONNECTOR-1
23 23

HDMI-
CONNECTOR-2
CN1001
WIRING DIAGRAMS

1 7
HDMI-
CONNECTOR-3

SIDE PC-RGB-IN

CN3006
1
USB JACK
LCD PANEL ASSEMBLY
30

HEADPHONE
JACK

PL12.2AWI
SP3801 SP3802
SPEAKER SPEAKER
L-CH R-CH
[TYPE B]

CL3801

COMPONENT
-Y/VIDEO-IN 1 4
CN3105 CN4001
CN3801
1 9
COMPONENT CL3101
FUNCTION CBA
-Pb-IN
9 1
COMPONENT AC CORD
-Pr-IN

AUDIO(L)-IN
TUNER UNIT

AUDIO(R)-IN 1 2
REAR
CN601
DIGITAL
AUDIO-OUT
(COAXIAL)

11-2
CN3601 CN631
ETHERNET
1 1
CONNECTOR
CL3701
DIGITAL MAIN CBA UNIT POWER SUPPLY CBA
23 23
PC-RGB-IN

HDMI-
CONNECTOR-1
CN1001
1 7
HDMI-
CONNECTOR-2

HDMI-
CONNECTOR-3

WIRELESS
SIDE LAN CN3904
MODULE
1

USB JACK LCD PANEL ASSEMBLY


30

HEADPHONE
JACK

PL12.2BWI
EXPLODED VIEWS
[TYPE A]

A1

LCD1

A20
L4 A2
CL3006
L4
A4

CL1001

A23
L4
Digital Main CBA Unit
S7
LCD Module

L4 A14
CL3701

L13

L4 L13
L51
B11 B3
L23 L13 CL3801 B9
L13 B18 A3
CL3101 L13 B17
Power Supply CBA B24
AC601 B18 B17
Function CBA

L14
L4
L32
SP3802
L13
L4 SP3801

L14

See Electrical Parts List A10 L4


A18
for parts with this mark.
S7

X6
SSK1

12-1 PL12.2_A CEX


[TYPE B]

A1

LCD1

A20
L4 A2
CL3006
L4
A4

CL1001

A23
L4
Digital Main CBA Unit
S7
LCD Module

L4 A14
CL3701

L13

L13
L4
L51
B11 B3
L23 L13 L13 CL3801
B9 B18
B17 A3
CL3101 L13
Power Supply CBA B24
AC601 B18 B17
Function CBA

L14
L4
L32
SP3802
L13
L4 SP3801

L14

See Electrical Parts List A10 L4


A18
for parts with this mark.
S7

X6
SSK1

12-2 PL12.2_B CEX


Packing
X9 X12 TYPE B SSK1

X17 X18

A10

Tape X7
X2
X3 X4

S3
S7

X1

S6

Packing Tape

S4

S4

S1

S7 Packing Tape

FR
ON
T

Packing Tape
Some Ref. Numbers are
not in sequence.

12-3 PL12.2PEX
TYPE A
PARTS LIST
[32PFL4507/F7 (Serial No.: DS1), 32PFL4507/F8 (Serial No.: XA1),
32PFL4507/F8 (Serial No.: DS1)]
Mechanical Parts
PRODUCT SAFETY NOTE: Products marked with a Ref. No. Description Part No.
# have special characteristics important to safety. ACCESSORIES
Before replacing any of these components, read X1 POLYETHYLENE BAG HDPE 180X340XT0.03 1EM435579
carefully the product safety notice in this service X2# OWNERS MANUAL A21F5UH 1EMN29143
manual. Don't degrade the safety of the product X3 REMOTE CONTROL TRANSMITTER YKF259- URMT34JHG001
001
through improper servicing.
X4 BATTERY R03-B500/01S XB0M451CZB01
NOTE: Parts that are not assigned part numbers X6 QUICK START GUIDE A21F5UH 1EMN29144
(---------) are not available. X7 REGISTRATION CARD(PHILIPS) A11P4UH 1EMN27321
X9 BROCHURE (PHILIPS) A01N2UH 1EMN26419
X12 CABLE MANAGEMENT TIE(BLACK) A01F2UH 1EM431197

Ref. No. Description Part No.


Depending on the model, the rear cover part number will differ.
for 32PFL4507/F7 (Serial No.: DS1)
A3 models 1EM028929 LCD PANEL ASSEMBLY
REAR COVER A21F5UH
for 32PFL4507/F8 (Serial No.: XA1, Ref. No. Description Part No.
A3 DS1) models 1EM127007 LCD1 LCD PANEL ASSEMBLY U24F1P0
REAR COVER A21FAMA Consists of the following
A1 FRONT CABINET A21F5UH 1EM028928
A4 DECORATION PLATE A21F5UH 1EM227003 A2 REAR FRAME PAINT A21F0UH 1EM332238
A10 STAND ASSEMBLY 32W A21F5UH 1EM029073 CL1001 FFC 7PIN 7P/P1.0/470MM WX1U24F0-F02
A14 JACK HOLDER A21F0UH 1EM226823 CL3006 FFC 30PIN 30P/P0.5/210MM WX1U24F0-F01
A18# RATING LABEL A21F5UH ---------- L4 SCREW P-TIGHT 3X12 BIND HEAD+ BLK GBHP3120
A20 LOGO LABEL A21F5UH ---------- L51 SCREW M3X4 M3X4 BIND+ (B-NI) SBH33040
A23 ENERGY GUIDE LABEL A21F5UH ---------- LCD MODULE ----------
AC601# AC CORD W/O A GND WIRE UL/CSA/1700/NO/ WAC1720LW005
BLACK
B9 STAND HOLDER A21F5UH 1EM028931
B11 SENSOR PLATE A21F5UH 1EM437078
B17 WALL MOUNT BRACKET A11N0UH 1EM434637
B18 WALL MOUNT COVER A2170UT 1EM332137
B24 STAND BRACKET A21F5UH 1EM226984
CL3101 FFC WIRE ASSEMBLY 9PIN 9PIN/WHITE/ WX1A21F0-111
143MM
CL3701 FFC WIRE ASSEMBLY 23PIN 23PIN/WHITE/ WX1A21F0-110
80MM
CL3801 WIRE ASSEMBLY 4PIN 4PIN/341MM&36MM WX1A21F5-302
L4 SCREW P-TIGHT 3X12 BIND HEAD+ BLK GBHP3120
L13 SCREW S-TIGHT M3X6 BIND HEAD+ GBJS3060
L14 S-TIGHT SCREW M3X6 BIND HEAD+BLACK GBHS3060
L32 DOUBLE SEMS SCREW M4X10 + BLK FPH34100
SP3801 SPEAKER MAGNETIC 8OHM/10W S0313F17 DS08100XQ001
SP3802 SPEAKER MAGNETIC 8OHM/10W S0313F17 DS08100XQ001
SSK1 STAND SCREW KIT A21F5UH 1ESA31176
PACKING
S1 CARTON A21F5UH 1EM332739
S3 STYROFOAM TOP A21F5UH 1EM029165
S4 STYROFOAM BOTTOM A21F5UH 1EM029166
S6 SET BAG A17F6UH 1EM330877
S7 SERIAL NO. LABEL A01PBUH ----------

2012/2/7 13-1 A21F5(A21FA)CA


Electrical Parts
PRODUCT SAFETY NOTE: Products marked with a Ref. No. Description Part No.
# have special characteristics important to safety. C1011 CAP ELE 47µF/100V/M/85 CEH4700V8006
Before replacing any of these components, read C1012 CHIP CERAMIC CAP.(3216) X7R K 1.0µF/100V CA2A105MR080
carefully the product safety notice in this service C1014 CHIP CERAMIC CAP.(1608) B K 1000pF/50V CHD1JK30B102
manual. Don't degrade the safety of the product C1016 CHIP CERAMIC CAP.(1608) B K 1µF/25V CHD1EK30B105
through improper servicing. C1017 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104
C1019 CHIP CERAMIC CAP.(1608) B K 4.7µF/6.3V CHD0KK30B475
NOTES: CONNECTORS
1. Parts that are not assigned part numbers (---------) CN601# CONNECTOR S2P3-VH (LF)(SN) JCVHC02JG002
are not available. CN631 FFC CONNECTOR IMSA-9615S-23A-PP-A JC96J23ER007
CN1001 FPC/FFC CONNECTOR IMSA-9615S-07A-PP- JC96J07ER007
2. Tolerance of Capacitors and Resistors are noted A
with the following symbols. DIODES
D401 DIODE SWITCHING HSS4148TE-E QDTZ0HSS4148
C.....±0.25% D.....±0.5% F.....±1% D402B DIODE ZENER 24BSB-T26 NDTB024BST26
D501 DIODE ZENER SMD UDZSNPTE-1733B QD1B0UDZNP33
G.....±2% J......±5% K.....±10%
D502 DIODE ZENER SMD UDZSNPTE-1730B QD1B0UDZNP30
M.....±20% N.....±30% Z.....+80/-20% D601 DIODE 1N5406BH NDL1001N5406
D602 DIODE 1N5406BH NDL1001N5406
D603 DIODE 1N5406BH NDL1001N5406
D604 DIODE 1N5406BH NDL1001N5406
DIGITAL MAIN CBA UNIT D605 ZENER DIODE MM5Z4V3B ND1BMM5Z4V3B
Ref. No. Description Part No. D607# DIODE ZENER 1ZB27BB NDWZ0001ZB27
DIGITAL MAIN CBA UNIT A21F5MMA-002 D608# DIODE ZENER 1ZB36BB NDWZ0001ZB36
D609# DIODE SWITCHING HSS4148TE-E QDTZ0HSS4148
D610 DIODE SWITCHING HSS4148TE-E QDTZ0HSS4148
POWER SUPPLY CBA D650 DIODE SCHOTTKY SB3150BH NDWZ00SB3150

Ref. No. Description Part No. D651 DIODE SCHOTTKY SB3150BH NDWZ00SB3150
D653 DIODE SHOTTKY SB3200BR NDWZ3200D027
POWER SUPPLY CBA A21F0MPW-001
Consists of the following D654# DIODE ZENER 1ZB30BB NDWZ0001ZB30
CAPACITORS D656 DIODE FAST RECOVERY RS1BJTB ND1Z0RS1BJTB
C501 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104 D657 ZENER DIODE MM5Z5V6B ND1BMM5Z5V6B
C602# SAFTY CAP. 1000pF/250V KX CA2E102MR101 D660 IC SHUNT REGULATOR SL431A-AT NSZBA0TAUK01
C603# SAFTY CAP. 1000pF/250V KX CA2E102MR101 D661B DIODE ZENER 5V6BSB-T26 NDTB5R6BST26
C604# CAP METALIZED FILM 0.22µF/275V/K CTA224PKR001 D662 IC SHUNT REGULATOR SL431A-AT NSZBA0TAUK01
C605 CAP ELE 330µF/200V/M/87 CEB3310S6016 D1001 DIODE SCHOTTKY SMD SK210TD ND1Z0SK210TD
C606 CERAMIC CAP. 820pF/2KV CA3D821PAN04 D1002 DIODE SWITCHING HSS4148TE-E QDTZ0HSS4148
C607 CHIP CERAMIC CAP. B K 1200pF/50V CHD1JK30B122 ICS
C608 CHIP CERAMIC CAP. B K 0.039µF/50V CHD1JK30B393 IC601# IC PHOTOCOUPLER TLP781F(D4-FUNBLL F) QPEL781FBLLF
C609# CHIP CER. BK 0.082µF/50V CHD1JK30B823 IC1001# IC LED BACKLIGHT CONTROLLER HA7209PC NSCA0T00H003
/SOP /24PIN
C610 CHIP CERAMIC CAP.(1608) B K 1000pF/50V CHD1JK30B102
C614# CAP METALIZED FILM 0.22µF/275V/K CTA224PKR001 COILS
C616# SAFTY CAP. 1000pF/250V KX CA2E102MR101 L601# COIL LINE FILTER JLB20154/18MH LLEG0Z0XB022

C650 CAP CERAMIC HV 2200pF/1KV B K CA3A222TE006 L602# COIL LINE FILTER JLB20154/18MH LLEG0Z0XB022

C651 CAP ELE 470µF/25V/M/85 CED4710V8006 L1001 POWER INDUCTORS CWKBNP-220K LLF2200KV002

C652 CAP ELE 470µF/25V/M/85 CED4710V8006 TRANSISTORS


C653 CAP ELE 470µF/25V/M/85 CED4710V8006 Q501# FET 2SK3498(T6L1FUNANQ QF1Z02SK3498
C654 CAP ELE 470µF/35V/M/85 CEE4710V8006 Q601# FET MOS TK8A50D(LS1FND3 QM QEE1TK8A50DM
C655 CAP ELE 470µF/35V/M/85 CEE4710V8006 Q602# TRANSISTOR 2SC2120-Y(TE2 F T) QQSY2SC2120F
C656 CAP ELE 1µF/50V/M/85 CEF1R00V8006 Q650 CHIP TRANSISTOR KTC3875S-Y-RTK/P NQ1YKTC3875S
C660 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104 Q652 CHIP TRANSISTOR KTC3875S-Y-RTK/P NQ1YKTC3875S
C663 CAP ELE 100µF/10V/M/85 CEB1010V8006 Q653 CHIP TRANSISTOR KTC3875S-Y-RTK/P NQ1YKTC3875S
C665 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104 Q656 TRANSISTOR 2SC2120-Y(TE2 F T) QQSY2SC2120F
C1001 CAP ELE 330µF/25V/M/85 CED3310V8006 Q1001# FET MOS SMD AP18T10AGH-HF NF2Z18T10AGH
C1003 CHIP CERAMIC CAP.(1608) B K 1µF/25V CHD1EK30B105 RESISTORS
C1004 CHIP CERAMIC CAP.(1608) B K 1µF/25V CHD1EK30B105 R401 RES CHIP 1608 1/10W J 8.2k Ω RRXA822HH013
C1006 CHIP CERAMIC CAP.(1608) B K 1000pF/50V CHD1JK30B102 R402 RES CHIP 1608 1/10W J 3.0k Ω RRXA302HH013
C1008 CHIP CERAMIC CAP.(3216) X7R K 1.0µF/100V CA2A105MR080 R501# METAL OXIDE FILM RES. 2W J 47 Ω RN02470ZU001
C1009 CHIP CERAMIC CAP.(3216) X7R K 1.0µF/100V CA2A105MR080 R502 RES CHIP 1608 1/10W J 1.5M Ω RRXA155HH013
C1010 CAP ELE 47µF/100V/M/85 CEH4700V8006 R601# RES. CARBON FILM J 1/2W J 1.2M Ω RCX2125T1003
R602 RES CEMENT 5W/J/1.2 Ω RWJ1R2PAK007

2012/01/06 13-2 A21F5EL.fm


Ref. No. Description Part No. Ref. No. Description Part No.
R603 RES CHIP 3216 1/4W J 330k Ω RRX4334HH034 BC1002 WIRE CP STP-S-0.50 XZ40F0REN001
R604 RES CHIP 3216 1/4W J 330k Ω RRX4334HH034 F601# FUSE STC4A125V U/CT PAGE20CW3402
R605 RES CHIP 3216 1/4W J 330k Ω RRX4334HH034 FH601 FUSE HOLDER MSF-015-RS-SN (B110) XH001Z0LY001
R606 RES CARBON FILM T 1/4W J 270 Ω RCX4271T1001 FH602 FUSE HOLDER MSF-015-RS-SN (B110) XH001Z0LY001
R607 RES CARBON FILM T 1/4W J 270 Ω RCX4271T1001 JS632 WIRE CP STP-S-0.50 XZ40F0REN001
R608 RES CARBON FILM T 1/4W J 1.5k Ω RCX4152T1001 L23 SCREW B-TIGHT D3X8 BIND HEAD+ GBJB3080
R611# METAL OXIDE RES. 2W J 0.36 Ω RN02R36ZU001 SA601# SURGE ABSORBER 470V+-10PER NVQZ10D471KB
R612 RES CARBON FILM T 1/4W J 2.2k Ω RCX4222T1001 T601# TRANS POWER BCK-28DZ LTT2PCMEK036
R613 RES CARBON FILM T 1/4W J 220 Ω RCX4221T1001
R614 RES CHIP 3216 1/4W J 330k Ω RRX4334HH034 FUNCTION CBA
R650 RES CARBON FILM T 1/4W J 5.6k Ω RCX4562T1001
R651# RES CHIP 1608 1/10W J 1.0 Ω RRXA1R0HH013 Ref. No. Description Part No.
R652 RES CHIP 1608 1/10W F 56.0k Ω RTW5602HH008 FUNCTION CBA A21F5MSW-001
Consists of the following
R653 RES CHIP 1608 1/10W F 22.0k Ω RTW2202HH008
CAPACITORS
R654 RES CARBON FILM T 1/4W J 180 Ω RCX4181T1001
C4001 CHIP CERAMIC CAP.(1005) B K 1µF/6.3V CHB0KK30B105
R655 RES CARBON FILM T 1/4W J 180 Ω RCX4181T1001
C4002 CHIP CERAMIC CAP.(1005) B K 2200pF/50V CHB1JK30B222
R657 RES CARBON FILM T 1/4W J 3.9k Ω RCX4392T1001
C4051 CHIP CERAMIC CAP.(2125) B K 10µF/6.3V CHE0KK30B106
R658 RES CHIP 1608 1/10W J 2.7k Ω RRXA272HH013
C4052 CHIP CERAMIC CAP.(1005) B K 1000pF/50V CHB1JK30B102
R659 RES CHIP 1608 1/10W F 22.0k Ω RTW2202HH008
C4053 CHIP CERAMIC CAP.(1005) F Z 0.1µF/16V CHB1CZ30F104
R660 RES CHIP 1608 1/10W F 2.70k Ω RTW2701HH008
C4054 CHIP CERAMIC CAP.(1005) F Z 0.1µF/16V CHB1CZ30F104
R661 RES CHIP 1608 1/10W F 3.30k Ω RTW3301HH008
C4056 CHIP CERAMIC CAP.(2125) B K 10µF/6.3V CHE0KK30B106
R662 RES CHIP 1608 1/10W F 3.30k Ω RTW3301HH008
R663 RES CHIP 1608 1/10W J 47k Ω RRXA473HH013 CONNECTOR
R664 RES CHIP 1608 1/10W J 10k Ω RRXA103HH013 CN4001 FFC CONNECTOR 9P 9611S-09Y916 JC96D09ER014

R665 RES CHIP 1608 1/10W J 10k Ω RRXA103HH013 DIODES


R668 RES CHIP 1608 1/10W J 22k Ω RRXA223HH013 D4001 ZENER DIODE MM5Z5V6B ND1BMM5Z5V6B
R669 RES CHIP 1608 1/10W J 10k Ω RRXA103HH013 D4003 ZENER DIODE MM5Z5V6B ND1BMM5Z5V6B
R670 RES CARBON FILM T 1/4W J 1.0k Ω RCX4102T1001 D4004 ZENER DIODE MM5Z5V6B ND1BMM5Z5V6B
R671 RES CARBON FILM T 1/4W J 1.0k Ω RCX4102T1001 D4051 LED WHITE SMD SML813WBC8W1 QP1Z13WBC8W1
R672 WIRE CP STP-S-0.50 XZ40F0REN001 IC
R673# RES CHIP 1608 1/10W J 5.6 Ω RRXA5R6HH013 IC4001 IC TOUCH SENSOR MICON CY8C20336A- NSCB0T0TY063
24LQXIT
R677 RES CHIP 1608 1/10W J 10k Ω RRXA103HH013
RESISTORS
R678 RES CARBON FILM T 1/4W J 5.6k Ω RCX4562T1001
R4001 CHIP RES. 1/16W J 560 Ω RRXG561HH004
R680 RES CHIP 1608 1/10W J 100 Ω RRXA101HH013
R4002 CHIP RES. 1/16W J 560 Ω RRXG561HH004
R681 RES CHIP 1608 1/10W F 10.0k Ω RTW1002HH008
R4003 CHIP RES. 1/16W J 560 Ω RRXG561HH004
R682 RES CHIP 1608 1/10W 0 Ω RRXA000HH014
R4004 CHIP RES. 1/16W J 560 Ω RRXG561HH004
R1001 RES CHIP 1608 1/10W J 10 Ω RRXA100HH013
R4005 CHIP RES. 1/16W J 560 Ω RRXG561HH004
R1002 RES CHIP 1608 1/10W J 200 Ω RRXA201HH013
R4006 CHIP RES. 1/16W J 560 Ω RRXG561HH004
R1003# METAL OXIDE RES. 1W J 0.18 Ω RN01R18ZU001
R4007 CHIP RES. 1/16W J 560 Ω RRXG561HH004
R1004 RES CHIP 1608 1/10W F 560k Ω RTW5603HH008
R4008 RES CHIP 1005 1/16W J 18k Ω RRXG183HH004
R1005 RES CHIP 1608 1/10W F 200k Ω RTW2003HH008
R4009 CHIP RES.(1005) 1/16W J 8.2k Ω RRXG822HH004
R1006 RES CHIP 1608 1/10W F 27.0k Ω RTW2702HH008
R4010 CHIP RES. 1/16W J 4.7k Ω RRXG472HH004
R1007 RES CHIP 1608 1/10W F 100k Ω RTW1003HH008
R4011 CHIP RES.(1005) 1/16W J 2.7k Ω RRXG272HH004
R1008 RES CHIP 1608 1/10W F 360 Ω RTW3600HH008
R4012 CHIP RES.(1005) 1/16W J 2.2k Ω RRXG222HH004
R1009 RES CHIP 1608 1/10W F 8.20k Ω RTW8201HH008
R4013 CHIP RES.(1005) 1/16W J 100 Ω RRXG101HH004
R1010 RES CHIP 1608 1/10W J 10k Ω RRXA103HH013
R4014 CHIP RES.(1005) 1/16W J 2.2k Ω RRXG222HH004
R1011 RES CHIP 1608 1/10W J 100k Ω RRXA104HH013
R4021 CHIP RES. 1/16W J 10 Ω RRXG100HH004
R1012 RES CHIP 1608 1/10W F 100 Ω RTW1000HH008
R4022 CHIP RES. 1/16W J 10 Ω RRXG100HH004
R1014 RES CHIP 1608 1/10W J 240 Ω RRXA241HH013
R4051 CHIP RES. 1/16W J 56 Ω RRXG560HH004
R1015 RES CHIP 1608 1/10W J 240 Ω RRXA241HH013
R4052 RES CHIP 1005 1/16W J 6.8k Ω RRXG682HH004
R1016 RES CHIP 1608 1/10W J 10k Ω RRXA103HH013
R4053 CHIP RES.(1005) 1/16W J 2.2k Ω RRXG222HH004
R1017 RES CHIP 1608 1/10W J 100k Ω RRXA104HH013
R4054 CHIP RES.(1005) 1/16W J 1k Ω RRXG102HH004
R1018 RES CHIP 1608 1/10W 0 Ω RRXA000HH014
R4062 CHIP RES.(1005) 1/16W 0 Ω RRXG000HH005
R1020 RES CHIP 1608 1/10W 0 Ω RRXA000HH014
R1021 RES CHIP 1608 1/10W 0 Ω RRXA000HH014 MISCELLANEOUS
R1502 RES CHIP 1608 1/10W 0 Ω RRXA000HH014 RS4051 SENSOR REMOTE RECEIVER GP1USC32XP USEJRS0SH004

R1503 RES CHIP 1608 1/10W 0 Ω RRXA000HH014


MISCELLANEOUS
B3 HEAT SINK PNI A11N5UH 1EM435557
BC601 BEADS INDUCTOR FBR07HA121SB-00 LLBF00STU030
BC602 BEADS INDUCTOR FBR07HA121SB-00 LLBF00STU030
BC603 BEADS INDUCTOR FBR07HA121SB-00 LLBF00STU030

2012/01/06 13-3 A21F5EL.fm


TYPE B
PARTS LIST [32PFL4907/F7 (Serial No.: DS1)]
Mechanical Parts
PRODUCT SAFETY NOTE: Products marked with a
# have special characteristics important to safety.
Before replacing any of these components, read
carefully the product safety notice in this service
manual. Don't degrade the safety of the product
through improper servicing.
NOTE: Parts that are not assigned part numbers
(---------) are not available.

Different parts from the original model


32PFL4507/F7 (Serial No. : DS1)

Ref. No. Description Part No.


A3 REAR COVER A27F5UH 1EM127000
A14 JACK HOLDER A27F0UH 1EM332537
A18# RATING LABEL A27F5UH ----------
A20 LOGO LABEL A27F5UH ----------
A23 ENERGY GUIDE LABEL A27F5UH ----------
CL3701 FFC WIRE ASSEMBLY 23PIN 23PIN/WHITE/ WX1A27F0-101
55MM
S1 CARTON A27F5UH 1EM437000A
X2# OWNERS MANUAL A27F5UH 1EMN29000A
X3 REMOTE CONTROL UNIT YKF255-010 URMT42JHG004
X6 QUICK START GUIDE A27F5UH 1EMN29104A
X17 VUDU SHEET E5S20UD 1VMN30133
X18 WIRELESS LAN ADAPTOR WU5502S UWLUSBACM004

20120203 13-4 A27F5CA


Electrical Parts
PRODUCT SAFETY NOTE: Products marked with a
# have special characteristics important to safety.
Before replacing any of these components, read
carefully the product safety notice in this service
manual. Don't degrade the safety of the product
through improper servicing.
NOTES:
1. Parts that are not assigned part numbers (---------)
are not available.
2. Tolerance of Capacitors and Resistors are noted
with the following symbols.

C.....±0.25% D.....±0.5% F.....±1%


G.....±2% J......±5% K.....±10%
M.....±20% N.....±30% Z.....+80/-20%

Different parts from the original model


32PFL4507/F7 (Serial No. : DS1)

Ref. No. Description Part No.


DIGITAL MAIN CBA UNIT A27F5MMA-002

POWER SUPPLY CBA A27F0MPW-001


C1007 CERAMIC CAP. 220pF/1KV CCD3AKN0B221
R653 RES CHIP 1608 1/10W F 47.0k Ω RTW4702HH008
R662 RES CHIP 1608 1/10W J 1.5k Ω RRXA152HH013
R670 RES CARBON FILM T 1/4W J 180 Ω RCX4181T1001
R671 RES CARBON FILM T 1/4W J 180 Ω RCX4181T1001
R672 RES CARBON FILM T 1/4W J 180 Ω RCX4181T1001
R680 RES CHIP 1608 1/10W F 10.0k Ω RTW1002HH008

20120203 13-5 A27F5EL


REVISION HISTORY

Chassis PL12.2
• 2012/01/13 32PFL4507/F7 (Serial No.: DS1) added
• 2012/02/07 32PFL4907/F7 (Serial No.: DS1) added
• 2012/02/10 32PFL4507/F8 (Serial No. : XA1) added
Note: Identical product to the 32PFL4507/F7 (Serial No.: DS1).
• 2012/05/23 32PFL4507/F8 (Serial No. : DS1) added
Note: Identical product to the 32PFL4507/F7 (Serial No.: DS1).

14-1 PL12.2REV
COMPARISON LIST OF MODEL NAMES

Chassis PL12.2
32PFL4507/F7 (DS1) A21F5UH

32PFL4907/F7 (DS1) A27F5UH

32PFL4507/F8 (XA1) A21FAMA

32PFL4507/F8 (DS1) A21FJMH

PL12.2COM

You might also like