Prog Consoles CQM1H-PRO01

Cat. No.
W341-E1-03
SYSMAC CS/CJ Series

CQM1H-PRO01-E/CQM1-PRO01-E/C200H-PRO27-E
Programming Consoles
OPERATION MANUAL
SYSMAC CS/CJ Series
CQM1H-PRO01-E/CQM1-PRO01-E/
C200H-PRO27-E
Programming Consoles
Operation Manual
Revised September 2001
iv
Notice:
OMRON products are manufactured for use according to proper procedures by a qualified operator
and only for the purposes described in this manual.
The following conventions are used to indicate and classify precautions in this manual. Always heed
the information provided with them. Failure to heed precautions can result in injury to people or dam-
age to property.
!DANGER Indicates an imminently hazardous situation which, if not avoided, will result in death or
serious injury.
!WARNING Indicates a potentially hazardous situation which, if not avoided, could result in death or
serious injury.
!Caution Indicates a potentially hazardous situation which, if not avoided, may result in minor or
moderate injury, or property damage.
OMRON Product References

All OMRON products are capitalized in this manual. The word “Unit” is also capitalized when it refers to
an OMRON product, regardless of whether or not it appears in the proper name of the product.
The abbreviation “Ch,” which appears in some displays and on some OMRON products, often means
“word” and is abbreviated “Wd” in documentation in this sense.
The abbreviation “PC” means Programmable Controller and is not used as an abbreviation for anything
else.
Visual Aids
The following headings appear in the left column of the manual to help you locate different types of
information.
Note Indicates information of particular interest for efficient and convenient opera-
tion of the product.
1,2,3... 1. Indicates lists of one sort or another, such as procedures, checklists, etc.
¸ OMRON, 1999
All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form, or
by any means, mechanical, electronic, photocopying, recording, or otherwise, without the prior written permission of
OMRON.
No patent liability is assumed with respect to the use of the information contained herein. Moreover, because OMRON is con-
stantly striving to improve its high-quality products, the information contained in this manual is subject to change without
notice. Every precaution has been taken in the preparation of this manual. Nevertheless, OMRON assumes no responsibility
for errors or omissions. Neither is any liability assumed for damages resulting from the use of the information contained in
this publication.
v
vi
TABLE OF CONTENTS
PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xi
1 Intended Audience . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xii
2 General Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xii
3 Safety Precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xii
4 Operating Environment Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xiii
5 Application Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xiv
SECTION 1
Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1-1 Applicable Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
1-2 Using the Programming Console . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1-3 Programming Console Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1-4 Unsupported Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
1-5 Functions and Nomenclature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
1-6 Programming Console Connection and Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
1-7 Comparison with Previous Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
SECTION 2
Using the Programming Console . . . . . . . . . . . . . . . . . . . . . 17
2-1 Programming. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
2-2 Connecting the Programming Console . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
2-3 Using the Programming Console for the First Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
2-4 Inputting Programs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
2-5 Checking Program Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
SECTION 3
Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
3-1 Starting Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
3-2 Changing Operating Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
3-3 Key Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
3-4 Clearing Memory Areas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
3-5 Buzzer Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
3-6 Selecting Tasks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
3-7 I/O Table Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
SECTION 4
Writing and Editing Programs . . . . . . . . . . . . . . . . . . . . . . . 51
4-1 Inputting Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
4-2 Reading and Searching Programs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
4-3 Editing Programs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
vii
TABLE OF CONTENTS
SECTION 5
Checking and Adjusting Programs . . . . . . . . . . . . . . . . . . . . 77
5-1 Reading Program Execution Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
5-2 Simple I/O Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
5-3 I/O Multipoint Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
5-4 Monitor Display Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
5-5 Changing Word (16-bit) Present Values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
5-6 Forcing Bits ON/OFF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
5-7 Differential Monitor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
5-8 Online Editing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
SECTION 6
Maintenance Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
6-1 Clock Read/Change . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112
6-2 Cycle Time Read . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113
6-3 Reading/Clearing Error Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114
SECTION 7
Memory Card Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . 119
7-1 File Memory Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120
7-2 Memory Card Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121
7-3 File Write . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122
7-4 File Read . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126
7-5 File Verify . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130
7-6 File Delete . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133
SECTION 8
PC Setup Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137
8-1 PC Setup Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138
Appendices
A ASCII Coding Sheet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141
B Error Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143
C PC Setup Setting Sheets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145
Index. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 153
Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 157
viii
$ERXWWKLV0DQXDO
This manual describes the installation and operation of the CQM1H-PRO01-E, CQM1-PRO01-E and
C200H-PRO27-E Programming Consoles for use with CS-series and CJ-series Programmable Con-
trollers and includes the sections described below.
The CS-series and CJ-series CPU Units are generally divided into two groups: CS1 CPU Units (CS1G/
H-CPU@@-EV1) and CJ1/CJ1-H/CS1-H CPU Units (CS1G/H-CPU@@H, CJ1G-CPU@@, and CJ1G/
H-CPU@@H).
Please read this manual and all related manuals listed in the following table carefully and be sure you
understand the information provided before attempting to use the CQM1H-PRO01-E, CQM1-PRO01-
E, or C200H-PRO27-E Programming Console to program, set up, or operate a PC System.
Name Cat. No. Contents
SYSMAC CS/CJ Series W341 Provides information on how to program and operate
Programming Consoles Operation Manual CS/CJ-series PCs using a Programming Console. (This
CQM1H-PRO01-E, CQM1-PRO01-E, manual)
C200H-PRO27-E
SYSMAC CS Series W339 Describes the installation and operation of the CS-
CS1G/H-CPU@@-EV1, CS1G/H-CPU@@H series PCs.
Programmable Controllers Operation Manual
SYSMAC CJ Series W393 Describes the installation and operation of the CJ-series
CJ1G-CPU@@, CJ1G/H-CPU@@H PCs.
Programmable Controllers Operation Manual
SYSMAC CS/CJ Series W394 Describes the ladder diagram programming functions
CS1G/H-CPU@@-EV1, CS1G/H-CPU@@H, and other functions supported by CS-series and CJ-
CJ1G-CPU@@, CJ1G/H-CPU@@H series PCs.
Programmable Controllers Programming Manual
SYSMAC CS/CJ Series W340 Describes the ladder diagram programming instructions
CS1G/H-CPU@@-EV1, CS1G/H-CPU@@H, supported by CS-series and CJ-series PCs.
CJ1G-CPU@@, CJ1G/H-CPU@@H
Programmable Controllers
Instructions Reference Manual
SYSMAC CS/CJ Series W342 Describes the Host Link and FINS communications
CS1G/H-CPU@@-EV1, CS1G/H-CPU@@H, commands used with CS-series and CJ-series PCs.
CS1W-SCB/21/41, CS1W-SCU21, CJ1G-
CPU@@, CJ1G/H-CPU@@H, CJ1W-SCU41
Communications Commands Reference Manual
WS02-CXPC1-E W361 Provides information on how to use the CX-Program-
CX-Programmer User Manual mer, a programming device that supports the CS/CJ-
series PCs.
!WARNING Failure to read and understand the information provided in this manual may result in per-
sonal injury or death, damage to the product, or product failure. Please read each section
in its entirety and be sure you understand the information provided in the section and
related sections before attempting any of the procedures or operations given.
ix
Section 1 gives a brief overview of the functions performed by the Programming Console, as well as
Programming Console specifications and connection procedures. It also lists the differences between
the operation of the Programming Consoles for CS/CJ-series PCs and previous Programming Con-
soles.
Section 2 provides information on how to set up the Programming Console for operation. It also
describes how to write a simple program from the Programming Console.
Section 3 describes the basic operations of the Programming Console, including initializing memory
and creating I/O tables. The three input modes available on the Programming Console are also
described.
Section 4 describes how to create and edit programs from the Programming Console.
Section 5 describes how to monitor programs in different display modes to check and modify the user
programs. Change values from various displays is also described.
Section 6 includes information on reading and setting the clock, reading the cycle time, and reading/
clearing error messages.
Section 7 provides information on how to format Memory Cards before use, and procedures for trans-
ferring data between Memory Cards and the CPU Unit.
Section 8 lists the settings in the PC Setup.
Appendix A provides a ASCII coding list, Appendix B provides a list of operating error messages,
and Appendix C provides a PC Setup Setting Sheets.
x
PRECAUTIONS
This section provides general precautions for using the Programmable Controller (PC) and related devices.
The information contained in this section is important for the safe and reliable application of the Programmable
Controller. You must read this section and understand the information contained before attempting to set up or
operate a PC system.
1 Intended Audience . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xii

2 General Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xii
3 Safety Precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xii
4 Operating Environment Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xiii
5 Application Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xiv
xi
Intended Audience 1
1 Intended Audience
This manual is intended for the following personnel, who must also have
knowledge of electrical systems (an electrical engineer or the equivalent).
• Personnel in charge of designing FA systems.
• Personnel in charge of managing FA systems and facilities.
2 General Precautions
The user must operate the product according to the performance specifica-
tions described in the operation manuals.
Before using the product under conditions which are not described in the
manual or applying the product to nuclear control systems, railroad systems,
aviation systems, vehicles, combustion systems, medical equipment, amuse-
ment machines, safety equipment, and other systems, machines, and equip-
ment that may have a serious influence on lives and property if used
improperly, consult your OMRON representative.
Make sure that the ratings and performance characteristics of the product are
sufficient for the systems, machines, and equipment, and be sure to provide
the systems, machines, and equipment with double safety mechanisms.
This manual provides information for programming and operating the Unit. Be
sure to read this manual before attempting to use the Unit and keep this man-
ual close at hand for reference during operation.
!WARNING It is extremely important that a PC and all PC Units be used for the specified
purpose and under the specified conditions, especially in applications that can
directly or indirectly affect human life. You must consult with your OMRON
representative before applying a PC System to the above-mentioned applica-
tions.
3 Safety Precautions
!WARNING Do not attempt to take any Unit apart while the power is being supplied. Doing
so may result in electric shock.
!WARNING Do not attempt to disassemble, repair, or modify any Units. Any attempt to do
so may result in malfunction, fire, or electric shock.
!Caution The CPU Unit refreshes I/O even when operation has been stopped in PRO-
GRAM mode. Always confirm safety before changing data in the output area
allocated to the Output Units or changing data in any memory area allocated
to Special I/O Units or CPU Bus Units using any of the following operations.
The loads connected to the Output Units, Special I/O Units, or CPU Bus Units
may operate unexpectedly.
• Transferring I/O memory to the CPU Unit using a peripheral device (per-
sonal computer software).
• Changing the present value using a peripheral device.
• Force-setting/resetting using a peripheral device.
• Transferring I/O memory files to the CPU Unit from the Memory Card or
EM File Memory.
xii
Operating Environment Precautions 4
• Transferring I/O memory data from other personal computers or host

computers on the network.
!Caution Confirm that the equipment is operating safely before starting actual opera-
tion.
!Caution Execute online edit only after confirming that no adverse effects will be
caused by extending the cycle time. Otherwise, the input signals may not be
readable.
!Caution Confirm that no adverse effect will occur in the system before executing online
edit.
4 Operating Environment Precautions

!Caution Do not operate the control system in the following places:
• Locations subject to direct sunlight.

• Locations subject to temperatures or humidity outside the range specified
in the specifications.
• Locations subject to condensation as the result of severe changes in tem-
perature.
• Locations subject to corrosive or flammable gases.
• Locations subject to dust (especially iron dust) or salts.
• Locations subject to exposure to water, oil, or chemicals.
• Locations subject to shock or vibration.
!Caution Take appropriate and sufficient countermeasures when installing systems in

the following locations:
• Locations subject to static electricity or other forms of noise.

• Locations subject to strong electromagnetic fields.
• Locations subject to possible exposure to radioactivity.
• Locations close to power supplies.
!Caution The operating environment of the PC System can have a large effect on the
longevity and reliability of the system. Improper operating environments can
lead to malfunction, failure, and other unforeseeable problems with the PC
System. Be sure that the operating environment is within the specified condi-
tions at installation and remains within the specified conditions during the life
of the system.
xiii
Application Precautions 5
5 Application Precautions
Observe the following precautions when using the PC System.
!WARNING Always heed these precautions. Failure to abide by the following precautions
could lead to serious or possibly fatal injury.
• Always connect to a class-3 ground (to 100 W or less) when installing the
Units. Not connecting to a class-3 ground may result in electric shock.
• Always turn OFF the power supply to the PC before attempting any of the
following. Not turning OFF the power supply may result in malfunction or
electric shock.
• Mounting or dismounting I/O Units, CPU Unit, Power Supply Units, In-
ner Boards, or any other Units.
• Assembling the Units.
• Setting DIP switches or rotary switches.
• Connecting or wiring the cables.
• Connecting or disconnecting the connectors.
!Caution Failure to abide by the following precautions could lead to faulty operation of
the PC or the system, or could damage the PC or PC Units. Always heed
these precautions.
• Fail-safe measures must be taken by the customer to ensure safety in the

event of incorrect, missing, or abnormal signals caused by broken signal
lines, momentary power interruptions, or other causes.
• Interlock circuits, limit circuits, and similar safety measures in external cir-
cuits (i.e., not in the Programmable Controller) must be provided by the
customer.
• Install external breakers and take other safety measures against short-cir-
cuiting in external wiring. Insufficient safety measures against short-cir-
cuiting may result in burning.
• Be sure that all the mounting screws, terminal screws, and cable connec-
tor screws are tightened to the torque specified in the relevant manuals.
Incorrect tightening torque may result in malfunction.
• Always use the power supply voltage specified in the operation manuals.
An incorrect voltage may result in malfunction or burning.
• Take appropriate measures to ensure that the specified power with the
rated voltage and frequency is supplied. Be particularly careful in places
where the power supply is unstable. An incorrect power supply may result
in malfunction.
• Do not apply voltages to the Input Units in excess of the rated input volt-
age. Excess voltages may result in burning.
• Do not apply voltages or connect loads to the Output Units in excess of
the maximum switching capacity. Excess voltage or loads may result in
burning.
• Wire the Unit correctly.
• Mount the Unit only after checking the terminal block completely.
xiv
Application Precautions 5
• Use crimp terminals for wiring. Do not connect bare stranded wires
directly to terminals. Connection of bare stranded wires may result in
burning.
• Leave the label attached to the Unit when wiring. Removing the label may
result in malfunction.
• Remove the label after the completion of wiring to ensure proper heat dis-
sipation. Leaving the label attached may result in malfunction.
• Disconnect the functional ground terminal when performing withstand
voltage tests. Not disconnecting the functional ground terminal may result
in burning.
• Check the orientation and polarity of terminal blocks and connectors
before connecting them.
• Be sure that the terminal blocks, expansion cables, and other items with
locking devices are properly locked into place. Improper locking may
result in malfunction.
• Double-check all the wiring before turning ON the power supply. Incorrect
wiring may result in burning.
• Check the user program for proper execution before actually running it on
the Unit. Not checking the program may result in an unexpected opera-
tion.
• Confirm that no adverse effect will occur in the system before attempting
any of the following. Not doing so may result in an unexpected operation.
• Changing the operating mode of the PC.
• Force-setting/force-resetting any bit in memory.
• Changing the present value of any word or any set value in memory.
• Transfer any essential data for restarting the PC, such as data memory
and hold bits to the CPU Unit before restarting the PC.
• Do not pull on the cables or bend the cables beyond their natural limit.
Doing either of these may break the cables.
• Do not place objects on top of the cables. Doing so may break the cables.
• When replacing parts, be sure to confirm that the rating of a new part is
correct. Not doing so may result in malfunction or burning.
• Before touching the Unit, be sure to first touch a grounded metallic object
in order to discharge any static built-up. Not doing so may result in mal-
function or damage.
xv
SECTION 1
Installation
This section describes the Programming Console used with CS/CJ-series PCs. It includes a brief overview of the functions
performed by the Programming Console, as well as Programming Console installation procedures.
1-1 Applicable Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

1-2 Using the Programming Console . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1-3 Programming Console Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1-4 Unsupported Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
1-5 Functions and Nomenclature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
1-5-1 Nomenclature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
1-5-2 The Mode Switch and Operating Modes . . . . . . . . . . . . . . . . . . . . . 10
1-5-3 Key Functions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
1-6 Programming Console Connection and Installation . . . . . . . . . . . . . . . . . . . . 14
1-7 Comparison with Previous Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
1
Applicable Models Section 1-1
1-1 Applicable Models

Applicable Programming Any of the following Programming Consoles can be used with CS/CJ-series
Consoles PCs: CQM1H-PRO01-E, CQM1-PRO01-E and the C200H-PRO27-E. The
Key Sheet and Connecting Cables listed below are required.
Programming Key Sheet Connecting Cables
Console
CQM1H-PRO01-E CS1W-KS001-E 2-m cable included
CQM1-PRO01-E CS1W-CN114 (0.05 m)
C200H-PRO27-E CS1W-CN224 (2.0 m) or CS1W-CN624
(6.0 m)
CS/CJ CS/CJ
CS/CJ
CS1W-N114
CS1W-KS001-E Connecting Cable: CS1W-KS001-E
CS1W-KS001-E
Key Sheet Connecting Cable 0.05 m Key Sheet
Key Sheet CS1W-CN224: 2.0 m
provided with the Connecting Cable
CQM1H-PRO01-E CS1W-CN624: 6.0 m
provided with the
CQM1H-PRO01-E
CQM1H-PRO01-E
CQM1-PRO01-E C200H-PRO27-E
The Programming Console is connected to the peripheral port on the CPU

Unit. It cannot be connected to the RS-232C port.
Applicable CPU Units

Series CPU Units Connectable ports
CS/CJ Series CS1H-CPU6@-EV1, Peripheral port
(See note.) CS1G-CPU4@-EV1, (The RS-232C port cannot be used.)
CS1G-CPU6@H,
CS1H-CPU4@H,
CJ1G-CPU4@,
CJ1H-CPU6@H, and
CJ1G-CPU4@H
Note CS1 CPU Units: CS1H-CPU6@-EV1 and CS1G-CPU4@-EV1

CS1-H CPU Units:CS1G-CPU6@H and CS1H-CPU4@H
CJ1 CPU Units:CJ1G-CPU4@
CJ1-H CPU Units:CJ1H-CPU6@H and CJ1G-CPU4@H
CS1 and CS1-H CPU Units:Collectively called the CS-series CPU Units.
CJ1 and CJ1-H CPU Units: Collectively called the CJ-series CPU Units.
2
Using the Programming Console Section 1-2
Operational Differences The operation of the Programming Console will vary with the CPU Unit that is
for CPU Units connected as shown in the following table. These are the only differences in
Programming Console operation that vary with the CPU Unit.
Operation CS Series CJ Series
CS1 CS1-H CJ1 CJ1-H
CPU Units CPU Units CPU Units CPU Units
Operating mode when at startup PROGRAM RUN
(when PC Setup is set to the
default setting and the Program-
ming Console is not connected)
Selecting the display language Pin 3 on DIP Programming Console key switch
switch on
front panel
of CPU Unit
1-2 Using the Programming Console

Programming Console The Programming Console for CS/CJ-series PCs is used to write, to make on-
site adjustments to, and to protect user programs. To create and edit relatively
large user programs, the CX-Programmer (running on a Windows computer)
should be used.
Programming Console Programming is started by using the CX-Programmer, a programming and

Features monitoring software package that runs on a Windows computer, to create the
program. Programming is completed by debugging the program on the PC.
The Programming Console is used after programming has been completed to
change the operating mode, change sections of the ladder program, monitor
operation, change present values in I/O memory, change the PC Setup, and
3
Using the Programming Console Section 1-2
read error information. The Programming Console can also be used to trans-
fer and verify data between EM File Memory and the PC.
One Cyclic Task More than One Cyclic Task
Indicates operations
Programming Programming which can be performed
from the Programming
Console
Checking the program
Creating I/O tables First rack words cannot be set.
PC Setup
Setting DM allocations
Transferring program to PC
Debugging Modifying the program
Online Editing
No
OK?
Yes
Changing the set values

Trial operation for timers/counters
Monitoring Making changes to

PC Setup
Setting DM allocation
No
OK?
Yes
Formatting Memory
Actual operation
Cards/EM File Memory
Transferring data between
Memory Cards/EM files
and the PC
Monitoring
Verifying data between
Reading error information Memory Cards/EM files
on current errors and the PC
Note The Programming Console cannot be used to create programs with more
than one cyclic task. Use the CX-Programmer if more than one cyclic task is
required.
4
Programming Console Functions Section 1-3
1-3 Programming Console Functions

The Programming Console performs the following functions.
Operational Settings
Buzzer Operation. See p42.
Memory Clear
All Clear
Specifying memory areas not to clear. See p38.
Memory Clear
Specifying the first program address to clear. See p41.

Specifying memory areas not to clear. See p41.
Creating/Verifying I/O Tables
I/O Table Create. See p45.

I/O Table Verify. See p48.
Maintenance
Reading/Clearing Error Messages. See p114.

Cycle Time Read. See p113.
Ladder Programming
Selecting Tasks See p43.
Program Read Setting Addresses See p65.

Searching Instruction Search See p66.
Bit Search See p67.
Program Write Instruction Write

Operand Input
Program Edit Instruction Change See p69.

Instruction Insert See p70.
Instruction Delete See p71.
Operand Change See p71.
N.O./N.C. Change See p72.
Instruction Variation Change See p73.
Timer/Counter SV change See p74.
Timer/Counter SV Change 1 (Sets constant or word)

Timer/Counter SV Change 2 (Fine adjustment of constant)
5
Programming Console Functions Section 1-3
Monitoring
Simple I/O Monitor See p79.
I/O Multipoint Monitor See p85.
Differential Monitor See p101.
Display Change
Signed Decimal Monitor See p90.
Unsigned Decimal Monitor See p91.
ASCII Monitor See p92.
Word (Multipoint) Monitor See p89.
SV Change
Hexadecimal/BCD Display Change See p93.
Signed Decimal Display Change See p94.
Unsigned Decimal Display Change See p96.
ASCII Display See p97.
Word (Multipoint) Display Change See p98.
Force Set/Reset
Force Set/Reset See p99.
Force Set/Reset All Clear See p101.
Online Editing See p96.
Program Edit Instruction Change See p102.

Instruction Insert See p104.
Instruction Delete See p105.
Bit Address Change See p106.
N.O./N.C. Change See p107.
Instruction Variation Change See p108.
Timer/Counter SV Change See p109.
Timer/counter SV Change 1 (Sets constant or word)

Timer/counter SV Change 2 (Fine adjustment of constant)
Special Functions
Clock Read/Change See p112.

PC Setup See Section 8.
Memory Card Operations See Section 7.
Data transfer from PC to Memory Card See p121.

Data transfer from Memory Card to PC See p126.
File Verify See p130.
File Delete See p133.
Memory Card format See p121.
6
Unsupported Functions Section 1-4
1-4 Unsupported Functions

The following operations cannot be performed on the Programming Console.
Use the CX-Programmer to perform these operations.
• Creating several cyclic tasks.
• Checking programs.
• Operations related to Communications Units.
• Displaying error history information.
• Setting the first rack words.
• Data tracing.
• Setting and clearing program read protection.
1-5 Functions and Nomenclature

Handling Precautions Although the Programming Console does not require regular maintenance,
observe the following precautions.
• Do not subject the Programming Console to excessive shock during
transportation or operation. Handle the keypad and the LCD display with
care.
• The C200H-PRO27-E Programming Console has two connectors. Use
only one of them at a time.
• Connect the cable to the Programming Console firmly until you hear it
click into place, indicating that the cable is locked firmly in place.
• When removing the cable, hold the levers on both sides of the cable,
release the lock, and pull the cable out.
• Do not pull or twist the cable with excessive force.
• The ambient operating temperature is 0 to 55C. Be careful that this tem-
perature is not exceeded when the Programming Console is used
mounted to a panel.
Operating Environment Do not install or operate the Programming Console in any of the following
locations.
• Locations subject to temperatures or humidities outside the ranges speci-
fied in the specifications.
• Locations directly subject to excessive shock.
• Locations subject to strong magnetic fields or electromagnetic waves.
• Locations subject to direct sunlight.
7
Functions and Nomenclature Section 1-5
1-5-1 Nomenclature
CQM1H-PRO01-E CQM1H-PRO01-E
LCD display
Mode switch
Keys
Note: Install the CS1W-JS001-E Key Sheet
Cable length: 2 m
(The CQM1H-PRO01-E can be connected
directly to the PC.) Connecting Cable
CS1W-CN114: 0.05 m
C200H-PRO27-E
LCD display
Mode switch
Keys
Note: Install the CS1W-KS001-E Key Sheet
Cassette connector jack
Connecting Cables
CS1W-CN224: 2.0 m
CS1W-CN624: 6.0 m
8
Mode Switch The mode switch key can be removed from the switch when the switch is in
RUN or MONITOR modes. It cannot be removed when in PROGRAM mode.
f
f MONITOR ✕
RUN PROGRAM
f: Key can be removed

✕: Key cannot be removed
Display Contrast The contrast of the liquid crystal display can be adjusted using the knob on
the right of the display.
Contrast adjustment knob
Buzzer Volume With the C200H-PRO27-E Programming Console, the buzzer volume can be
adjusted using the lever on the right-hand side of the Console. The CQM1H-
PRO01-E and CQM1-PRO01-E does not have buzzer volume control.
Buzzer volume minimum
Buzzer volume maximum
C200H-PRO27-E
Programming
Console
Refer to 3-5 Buzzer Operation for further information on adjusting the buzzer
volume.
9
1-5-2 The Mode Switch and Operating Modes

The relation between the operating mode of the CPU Unit and the mode
switch is as follows:
Key operation Operating Function
mode
MONITOR PROGRAM The CPU Unit is stopped. Programming opera-
RUN PROGRAM mode tions, such as writing or changing programs,
clearing memory, and checking the program,
can be performed.
MONITOR MONITOR The CPU Unit is operating and I/O processing

RUN PROGRAM mode is being performed. In this mode, CPU Unit
operation can be monitored and functions
such as forcing bits ON/OFF, changing timer/
counter SV/PC, changing word data PVs, and
online editing can be used. This mode is often
used for making program adjustments and for
trial system operations.
MONITOR RUN mode Used for normal operation of the CPU Unit.
RUN PROGRAM The operating status of the CPU Unit can be
monitored in this mode, but functions such as
forcing bits ON/OFF and changing PVs and
SVs cannot be performed.
Startup Operating Mode The operating mode of the CPU Unit when the power is turned ON depends
on the status of address 81 in the PC Setup (Startup Mode) and the connec-
tion status of peripheral devices.
Startup Mode setting in Peripheral device Startup operating mode
PC Setup (address 81)
PRCN: Mode set on Pro- Nothing connected CS1 CPU Unit:
gramming Console’s PROGRAM mode
mode switch CJ1/CJ1-H/CS1-H CPU Unit:
RUN mode
Programming Con- The mode set on the mode switch on
sole connected the Programming Console
Peripheral device CS1 CPU Unit:
other than Pro- PROGRAM mode
gramming Con- CJ1/CJ1-H/CS1-H CPU Unit:
sole connected RUN mode
PRG: PROGRAM mode Not relevant PROGRAM mode
MON: MONITOR mode Not relevant MONITOR mode
RUN: RUN mode Not relevant RUN mode
10
1-5-3 Key Functions

Each key has three possible inputs: The normal input, a shift input, and a text
input. Refer to page 37.
Shift input Shift input
AR A
FUN Normal input HR Normal input 0 Normal input
A L 0
Text input Text input Text input
• Press the SHIFT Key first to use the shift input.

• Press the SHIFT and then TEXT Keys first to use the text input.
Note Keystrokes for procedures are illustrated using graphics of the buttons on the
keypad for each step. The following list provides key names used in the text of
this manual.
Key Name Normal input Shift input Text input
FUN Key Function code --- A
FUN
A
Select/change task
PC Setup
(shift, monitor etc.)
SFT Key SFT --- B
SFT
B
NOT Key NOT --- C

NOT
C
,IR+
,IR+/,IR Key ,IR ,IR+ D
(Indirect index register)
,IR D
DR
DR/IR Key IR DR E
IR E
(Direct index register) (Data register)
SHIFT Key Alters the function of --- F

SHIFT other keys.
F
TN
TN/AND Key AND --- G
AND
G
ST
ST/OR Key OR --- H
OR
H
TK
TK/CNT Key CNT (Counter) TK (Task flag) I
CNT
I
,–IR
,–IR/TR Key Display changes ,–IR J
TR TR (Temporary bit) (Index register
DISP J auto-decre-
ment)
*EM
EM/WR.LR WR (Work bits) EM K
WR/LR Key LR (Link bits) Indirect EM
K (Extended
data memory)
AR
AR/HR Key HR (Holding bits) AR L
HR (Auxiliary bits)
L
11

AA
AA/LD Key LD --- M
LD
M
AC
AC/OUT Key OUT --- N
OUT
N
TIM Key TIM (Timer) --- O

TIM
O
EM
EM/DM Key DM (Data memory) EM P
DM (Data memory
P of current
bank)
CH
CH/DM Key DM CIO word Q
*DM (Indirect data memory)
Q
CONT
CONT/# Key #Constant Operand R
# (Binary or BCD) (Bit address)
R
*EM_
*EM_/EM_.EXT EM_ EM (indirect S
EM_/EXT Key (Expansion Data Mem- address)
S ory including bank
number)
EXT (memory all clear)
CHG Key CHG --- T
CHG (Changes to SVs,
T timer/counter etc.)
CF/SRCH Key SRCH CF U
CF
SRCH
(Condition
U Flag)
SET Key SET OFF-ON dif- V
SET ferentiation
V
Force Reset
DEL Key DEL (Delete) --- W
DEL
W
MON Key MON --- X

MON (Simple I/O Monitor, I/O
X Multipoint Monitor,
Memory area)
RESET Key RESET ON-OFF dif- Y
RESET ferentiation
Y
Force Reset
INS Key INS (Insert) --- Z
INS
Z
TEXT/! Key ! Alphanumeric ---

TEXT
(Immediate refresh) input mode
!
CLR Key Clear values --- Returns to

CLR Return to previous the normal
value input mode.
VRFY Key VRFY (Verify) --- ---
VRFY
WRITE Key WRITE --- ---

WRITE
12

Up Key Return to the previous Differential ---
↑ program address Monitor
Delete/write
Down Key Proceed to the next Differential ---
↓ program address Monitor
Move to the next set-
ting
A Numeric Keys Hexadecimal
0 0 A 0
0

F
5 5 5
5 F

9 9 9
9
Key Layout
,IR+ DR
FUN SFT NOT SHIFT
,IR IR
A B C D E F
TN ST TK ,–IR *EM AR
AND OR CNT TR WR/LR HR
G H I DISP J K L
AA AC EM CH CONT
LD OUT TIM DM *DM #
M N O P Q R
*EM_ CF
7 8 9 EM_/EXT CHG SRCH
7 8 9 S T U
E F
4 5 6 SET DEL MON
4 5 6 V W X
B C D
11 22 33 RESET INS ↑
Y Z
A TEXT
00 !
CLR VRFY WRITE ↓
13
Programming Console Connection and Installation Section 1-6
1-6 Programming Console Connection and Installation

Connection The Programming Console can be connected even when power is being sup-
plied to the PC and regardless of whether the CPU Unit is in RUN, MONITOR,
or PROGRAM mode.
1,2,3... 1. For the C200H-PRO27-E Programming Console, connect the Connecting

Cable’s (CS1W-CN224 or CS1W-CN624) connector to the Programming
Console.
a) The C200H-PRO27-E has two cable connectors. Use one of these
connectors and retain the detached cover as shown in the diagram be-
low.
Cover Open the cover with a small

flat-blade screwdriver or
fingernail
b) Check the direction of the connector and insert it until you hear a click
to secure it firmly in place.
2. Connect the Programming Console Cable to the peripheral port. Do not

connect it to the RS-232C port.
CS-series PCs
Always connect to the peripheral port.
Check the direction of the

connector and insert it until a
click is heard, securing it firmly
in place.
The RS-232C port cannot be used.
14
Programming Console Connection and Installation Section 1-6
CJ-series PCs

connector. Squeeze in on the sides of the
connector and then insert it.
3. To disconnect the connector, squeeze the lock release levers on the sides
and pull the connector straight out.
Lock release lever
Panel Mounting Use the C200H-PRO27-E Programming Console when the Programming
Console needs to be mounted to a panel. Follow the instructions below for
mounting the Console to a panel. (The C200H-ATT01 Mounting Bracket is
sold separately.)
Mounting hole dimensions
(DIN43700 standards)
Mounting Bracket
Two screws
186+1.1
-0
92+0.8
-0
Panel thickness: 1.0 to 3.2 mm
When mounting the Console to a panel, allow enough space for the cables.
37
15
At least 80 mm is required.
Either connector may

be used.
About 70 mm is required.
15
Comparison with Previous Models Section 1-7
Attaching the Key Sheet To attach the Key Sheet to the Programming Console, slide it under the
grooves on the front of the Unit to insert. (The CS1W-KS001-E Key Sheet is
sold separately.)
1-7 Comparison with Previous Models

Inputting Programs with END(001) Instruction Displayed
When the END(001) instruction is displayed, programs can be input in the
insert mode. In the following example, LD 000100 is input.
000000 CT00
END(001)
AA 000000
1 0 0
LD LD 000100
000001
WRITE
END (001)
• When memory is cleared using All Clear, the END instruction will be writ-
ten to the first address 000000. The NOP instruction is not written to all
program addresses as in previous models.
• If the END instruction is deleted, ADR OVER will be displayed and a
buzzer will sound.
• When programs are input, it is performed as an overwrite operation, as
with previous models. Therefore to insert instructions into a program, this
operation must be performed as an insert operation.
I/O Multipoint Monitor Display

The I/O Multipoint Monitor display is 2 rows. In previous models it was a 3-col-
umn display.
Start Mode
If default startup mode (i.e.,for the PC to start up in the mode set on the Pro-
gramming Console) is set in the PC Setup and a Programming Console is not
connected, a CS1 CPU Unit will start in PROGRAM mode, but a CJ1/CJ1-H/
CS1-H CPU Unit PC will start in RUN mode.
16
SECTION 2
Using the Programming Console
This section provides information on how to setup the Programming Console for operation. It also describes how to write
a simple program from the Programming Console.
2-1 Programming. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
2-2 Connecting the Programming Console . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
2-2 Connecting the Programming Console . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
2-3 Using the Programming Console for the First Time . . . . . . . . . . . . . . . . . . . . 19
2-4 Inputting Programs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
2-5 Checking Program Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
17
Programming Section 2-1
2-1 Programming
When using Programming Consoles for a CS/CJ-series PC for the first time,
use the following procedure. Details are described in the sections &RQ
QHFWLQJWKH3URJUDPPLQJ&RQVROH through 8VLQJWKH3URJUDPPLQJ&RQ
VROHIRUWKH)LUVW7LPH.
1,2,3... 1. Turn OFF the power supply to the Power Supply Unit.
2. Install the RAM backup battery into the CPU Unit.
3. Set the DIP switch on the CPU Unit as follows:
Pin 1: OFF (Data can be written to the UM area.)
Pin 3: ON (English messages) (CS1 CPU Units only)
Pin 4: OFF (Peripheral port automatic recognition.)
Note Be sure to turn OFF pin 1 and pin 4 to enable writing the program via
the Programming Console.
4. Connect the Programming Console to the CPU Unit.
5. Set the mode switch on the Programming Console to PROGRAM.
6. Be sure that the Programming Console’s operating mode switch is set to
PROGRAM, and then turn ON the power supply to the CPU Unit.
Note Any program in the CPU Unit will be executed if the operating mode
is not set to PROGRAM.
7. Select the display language (CJ1/CJ1-H/CS1-H CPU Units only).
8. Enter the password. (Press the CLR and MON Keys.)
9. Clear all memory.
10. Create I/O tables.
Note a) For CS-series PCs, I/O tables must be created.
b) For CJ-series PCs, I/O tables must be created to detect incorrect
Units or to register unused words. Otherwise, they are not re-
quired.
11. Read and clear error messages.
12. Start programming.
18
Connecting the Programming Console Section 2-2
2-2 Connecting the Programming Console

The Programming Console can be connected even when power is being sup-
plied to the PC and regardless of whether the CPU Unit is in RUN, MONITOR,
or PROGRAM mode.
Note Always connect the Programming Console Cable into the peripheral port. Do
not connect it to the RS-232C port.
CS-series
Insert a small flat-blade Check the direction of the connector. Connect by pressing the
screwdriver into the opening at connector tab in place.
the top of the Console and pull
forwards.
CJ-series

connector. Squeeze in on the sides of the
connector and then insert it.
2-3 Using the Programming Console for the First Time

When using the Programming Console for the first time, perform the following
procedure.
Note Keystrokes for procedures are illustrated using graphics of the keypad buttons
for each step. A list of key names used in the text is provided in Section 1
Installation on page 11.
1,2,3... 1. Make sure that the mode switch is set to PROGRAM, and then turn ON the
power supply to the Power Supply Unit.
MONITOR
RUN PROGRAM
19
Using the Programming Console for the First Time Section 2-3
The Programming Console can be connected even when power is being

supplied to the PC and regardless of whether the CPU Unit is in RUN,
MONITOR, or PROGRAM mode.
2. When the power is turned ON, the POWER indicator on the Power Supply
Unit will light and the LCD display on the Programming Console will display
the following.
Power ON
CS1 CPU Unit

<PROGRAM>
PASSWORD!
CJ1/CJ1-H/CS1-H CPU Unit
<PRG> 3:JPN~ENG
PASSWORD!
• Enter the password.
CS1 CPU Unit
CLR MON <PROGRAM> BZ
CJ1/CJ1-H/CS1-H CPU Unit

<PRG> BZ
3:JPN~ENG
• The Programming Console is equipped with a password so that the PC
is operated only by experienced staff to ensure safe operation and pre-
vent accidents. It will be necessary to enter the password by pressing
the CLR Key and then the MON Key after the power is turned ON or
after the Programming Console is connected. Refer to 6WDUWLQJ2S
HUDWLRQ for details.
• The key buzzer can be turned OFF by pressing the SHIFT Key and
then the 1 Key after entering the password.
3. Access the initial display.
000000 CT**
CLR
• If a memory error is displayed, press the CLR Key several times to re-
turn to the initial display.
• If an I/O table verification error occurs, I/O VRFY ERR will be dis-
played. Either connect the correct Unit, or press the CLR Key to ignore
the error.
4. Clear all memory.
• The memory clear operation initializes (formats) the memory area.
20
Using the Programming Console for the First Time Section 2-3
000000CLR MEM ?
NOT
SET RESET CHWA TCDE P
MON
000000CLR MEM ?
0:ALL 1:TASK
• To create one cyclic task only, select 0: ALL.
000000 CLR ALL ?

0
INT 0:NO 1:YES
• To create one cyclic task and one or more interrupt tasks, select INT
1: YES. To create one cyclic task only, select INT 0: NO.
000000 CLR ALL ?

0
INT 0:NO
MON
000000CLR'G MEM
INT 0:NO
000000 CLR ALL

END 0:NO
• When creating an interrupt task always select INT 1: YES when clear-
ing memory. If INT 0: NO is selected, you will not be able to create in-
terrupt tasks and it will be necessary to clear memory again using INT
1: YES.
Note The Programming Console cannot be used to create programs with
more than one cyclic task. Use the CX-Programmer if more than one
cyclic task is required.
5. Create an I/O table using the procedure given on page 45. With CS1-se-
ries PCs, an I/O table must be created.
6. Read/clear error messages.
If an error message is displayed, pressing the MON Key after removing the
cause of the error will clear the error message display. If there are several
error messages, repeat this operation several times.
000000
FUN
FUN (???)
MON
ERR/MSG
CHK OK
000000 CT00
CLR
21
Inputting Programs Section 2-4
2-4 Inputting Programs

When preparations for operation have been completed, input the following
simple program to get accustomed to using the Programming Console.
The following programs will be used in this example.
Cyclic task No. 0 (CT00) Interrupt task No. 2 (IT002)
000000 000001 000100 000000 002001
MOV(021)
#00FF
000100 TIM0000
D00100
#0100
T0000 000101
END(001) END(001)
Mnemonic Mnemonic
Program Program
address Instruction Operand address Instruction Operand
000000 LD 000000 000000 LD 000000
000001 OR 000100 000001 AND 002001
000002 AND NOT 000001 000002 MOV(021)
000003 OUT 000100 000003 --- #00FF
TIM 0000 000004 --- D00100
000004 #0100 000005 END(001) ---
000005 LD T0000
000006 OUT 000101
000007 END(001) ---
• When inputting the above program, always select 1: YES when clearing
memory to enable inputting the interrupt task. Refer to page 20.
Refer to the CS1 Operation Manual for further details on programming.
1,2,3... 1. Access the initial display.
CLR 000000 CT00

¡
Program address No. Task No.

2. Press the Down Key.
000000 CT00
↓ END(001)
When the Down Key is pressed, the END instruction will be generated.
When all memory has been cleared, the END instruction will be written to
program address 0 of all tasks.
22
New programs will be written from the address where the END instruction
is displayed.
3. Input the cyclic task program using the following steps.
a) Input LD 000000.
000000
LD 0
LD 000000
Leading zeros do not
need to be entered.
b) Press the WRITE Key.

Write will be displayed temporarily. When inputting is complete, the
address will move forward by one and the END instructions will auto-
matically be sent to the next address.
000001 CT00
WRITE
END(001)
Note Inputs are generally written into memory by overwriting the current
memory contents. Inputs are inserted only when the END(001) in-
struction is displayed on the Programming Console.
c) Input OR 000100
ST 000001
1 0 0
OR OR 000100
000002 CT00
WRITE
END(001)
d) Input AND NOT 000001
AND NOT 1
000002
AND N 000001
The NOT instruction is displayed as "N."
000003 CT00
WRITE
END(001)
e) Input OUT 000100.
000003
OUT 1 0 0
OUT 000100
000004 CT00
WRITE
END(001)
f) Input the TIM (timer) instruction.
000004
TIM
TIM 0000
000004 TIM
WRITE
SV #0000
000004 TIM
1 0 0
SV #0100
23
000005 CT00
WRITE
END(001)
g) Input LD TIM 00000.
AA 000005
TIM
LD LD T0000
000006 CT00
WRITE
END(001)
h) Input OUT 000101
000006
OUT 1 0 1
OUT 000101
000007 CT00
WRITE
END(001)
4. Read and check the cyclic task program using the following steps.
a) Access the initial display.
000000 CT00
CLR
¡
b) Press the Down Key, read the program in order, and confirm that the
mnemonics are correct. Correct any errors in the program.
000000 CT00
↓ LD 000000
000001 CT00
↓ OR 000100
000002 CT00
↓ AND N 000001
000003 CT00
↓ OUT 000100
000004 CT00
↓ TIM 0000
000004 TIM
↓ SV #0100
000005 CT00
↓ LD T0000
000006 CT00
↓ OUT 000101
000008 CT00
↓ END(001)
24
5. Switch to interrupt task using the following steps.

a) Access the initial display.
000000 CT00
CLR
¡
b) Switch tasks.
000000 CT00
FUN
FUN(???)
0:CYCLE TASK
CHG
1:INTRPT
INTRPT #?
1
000
000000 IT002
2 WRITE
6. Input the interrupt task program using the following steps.

a) Input LD 000000
AA 000000
0
LD LD 000000
000001 IT002
WRITE
END(001)
b) Input AND 002001.
000001
AND 2 0 0 1
AND 002001
000002 IT002
WRITE
END(001)
c) Input MOV(021).
000002
FUN
FUN (???)
000002
0
FUN (0??)
000002
2
FUN (02?)
000002
1
MOV(021)
000002 MOV
WRITE ↓ SV A 0000
or
Note When writing special instructions be sure to input the function num-
ber correctly as a 3-digit number. If the number is abbreviated to “0,”
25
Checking Program Operation Section 2-5
it cannot be written. Press the FUN Key once more and input correct-
ly.
d) Input the data to be sent.
CONT
SHIFT
F
SHIFT
F 000002 MOV
5 5
# SV A #00FF
000002 MOV
WRITE ↓ SV B 0000
or
EM 000002 MOV
1 0 0
DM SV B D00100
000003 IT002
WRITE
END(001)
Note Always press the WRITE Key after inputting the last set value. Write
cannot be performed using the Down Key.
7. Read and check the interrupt task program using the following steps.
a) Bring up the initial display.
000000 IT002
CLR
¡
b) Press the Down Key, read the program in order, and confirm that the
mnemonics are correct. Correct any errors in the program.
000000 IT002
↓ LD 000000
000001 IT002
↓ AND 002001
000002 IT002
↓ MOV(021)
000002 MOV
↓ SV A #00FF
000002 MOV
↓ SV B D00100
000003 IT002
↓ END(001)
2-5 Checking Program Operation

After checking that the program has been written correctly, perform a trial exe-
cution of the program. It is not necessary to have I/O Units installed, but when
the PC is switched to MONITOR mode, operation will start, so if I/O Units are
connected, either remove the output wires or set the Output OFF Bit to ON.
Refer to page 35.
1,2,3... 1. Switch to MONITOR mode by setting the mode switch on the Programming
Console to MONITOR mode.
26
The PC will start executing the program in MONITOR mode.

MONITOR MONITOR
RUN PROGRAM RUN PROGRAM CS-series PCs
<MON> BZ
CJ-series PCs
<MON> BZ
3:JPN~ENG
2. Access the initial display.
000000 IT002
CLR
¡
3. Switch to the cyclic task.
0:CYCLE TASK
FUN CHG
1:INTRPT
000000 CT00
0 WRITE
4. Monitor the I/O bit status step by step during program execution.
Press the Up and Down Keys to read the program and monitor I/O bit sta-
tus as shown below. This operation is called monitoring I/O bit status.
The status resulting from one complete cycle of execution is shown on the
display when monitoring I/O bit status, not the status during program exe-
cution.
000000 CT00 0 OFF

↓ LD 000000
000001 CT00 0 OFF

↓ OR 000100
000002 CT00 1 ON
↓ AND N 000001
When a normally closed bit is OFF, the I/O bit status will be displayed as
“1.”
000003 CT00 0 OFF

↓ OUT 000100
5. Monitor bit status as described next.

Check to see whether or not CIO 000100 turns ON and holds itself ON
when CIO 000000 is turned ON.
a) Monitor CIO 000000. (Simple I/O Monitor)
000000 CT00
CLR
¡
SHIFT
CONT 000000
# BIT 000000
27
MON
000000 ^ OFF
b) Monitor CIO 000100 at the same time. (I/O Multipoint Monitor)
CONT 000100
SHIFT 1 0 0
# 000000 ^ OFF
MON
000100 ^ OFF
000000 ^ OFF
• The most recently monitored bits will be displayed first.
• I/O Multipoint Monitor can be used to monitor not only bits, but also
words (16-bit data), data memory, and timer/counter present values.
Up to 4 items can be specified.
6. Force ON CIO 000000 as described next.
a) Press the MON Key until CIO 000000 is displayed at the top.
MON
000000 ^ OFF
000100 ^ OFF
For I/O Multipoint Monitor, the uppermost bit is force set/reset.
b) Force ON CIO 000000.
When the SET Key is pressed:
000000 ^ ON
SET 000100 ^ ON
When the SET Key is released:
000000 ^ OFF
000100 ^ ON
• When there is no I/O Unit at word 0, the status is held ON. When the
RESET Key is pressed, the status is set to OFF.
• The uppermost bit CIO 000000 is only set to ON, while the SET Key is
being pressed.
• The program is being executed so when CIO 000000 is ON CIO
000100 is also ON. (Even when CIO 000000 is OFF, CIO 000100 will
hold ON.)
7. Force OFF CIO 000001 as described next.
a) Monitor CIO 000001. To monitor CIO 000001, press the Down Key at
the monitor display for CIO 000000.
000001 ^ OFF
↓ 000100 ^ ON
b) Use Force Set to set normally closed bit 000001 to OFF.
When the SET key is pressed:
000001 ^ ON
SET 000100 ^ OFF
When the SET Key is released:
28
000001 ^ OFF
000100 ^ OFF
• When there is no I/O Unit at word 0, the status is held ON. When the
RESET Key is pressed, the status is set to OFF.
• When the normally closed CIO 000001 is set to OFF, the self-holding
status is cleared, and CIO 000100 is set to OFF also.
8. Check timer operation using the following steps.
a) Monitor TIM 0000.
MON
000100 ^ OFF
000000 ^ OFF
MON
T0000 0100
TIM
000100 ^ OFF
b) Move bit CIO 000000 to the top.
MON
000000 ^ OFF
T0000 0100
SET
000000 ^ ON
T0000 0099
The timer starts a decrementing count.
000000 ^ ON
T0000 0000
The time up mark will be displayed.
c) Check bit CIO 000101.
MON
000100 ^ ON
000000 ^ OFF
000101 ^ ON
↓ 000000 ^ OFF
29
SECTION 3
Operation
This section describes the basic operations of the Programming Console, including initializing memory and creating I/O
tables. It also covers the 3 input modes available on the Programming Console.
3-1 Starting Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

3-1-1 CS1 CPU Units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
3-1-2 CJ1/CJ1-H/CS1-H CPU Units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
3-2 Changing Operating Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
3-3 Key Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
3-4 Clearing Memory Areas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
3-4-1 All Clear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
3-4-2 Memory Clear. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
3-5 Buzzer Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
3-6 Selecting Tasks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
3-7 I/O Table Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
3-7-1 I/O Table Create . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
3-7-2 I/O Table Verify . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
31
Starting Operation Section 3-1
3-1 Starting Operation

3-1-1 CS1 CPU Units
A password must be entered before any key operations can be performed.
This is necessary whenever the power to the Power Supply Unit is turned ON
when the Programming Console is connected to the CPU Unit, or when the
Programming Console is connected while the power is ON.
1,2,3... 1. When the power to the PC is turned ON, the POWER indicator on the CPU
the following.
<PROGRAM>
PASSWORD!
2. Enter the password (i.e., the CLR and MON Keys). The mode display will
appear.
MON
<PROGRAM> BZ
CLR
Note The Programming Console is equipped with a password so that the

PC is operated only by qualified staff to ensure safe operation and
prevent accidents.
• After entering the password, Programming Console key operations
can be performed and the mode can be changed.
then the 1 Key after entering the password. Refer to 3-5 Buzzer Oper-
ation.
3. Press the CLR Key to move from the mode display to the initial display.
CLR
000000 CT**
Task No.
Note When the power is turned ON for the first time (before All Clear has
been performed), “CT” will be displayed as the task number.
• When a memory error is displayed, press the CLR Key several times
to go to the initial display.
• To return to the mode display from the initial display, press the SHIFT
then CLR Keys.
SHIFT
<PROGRAM> BZ
CLR
Note If the Programming Console display is in Japanese for a CS1 CPU

Unit, turn the PC OFF once and change the CPU Unit’s DIP switch
setting. Refer to page 18.
32
3-1-2 CJ1/CJ1-H/CS1-H CPU Units

A password must be entered before any key operations can be performed.
This is necessary whenever the power to the Power Supply Unit is turned ON
when the Programming Console is connected to the CPU Unit, or when the
Programming Console is connected while the power is ON.
The language that Programming Console messages will be displayed can be
selected from the password or mode display. (There is no DIP switch setting
for the language, as there is for the CS1 CPU Units.)
1,2,3... 1. When the power to the PC is turned ON, the POWER indicator on the CPU
the following.
<PRG> 3:JPN~ENG
PASSWORD!
2. Press the 3 Key to switch between Japanese (JPN) and English (ENG) lan-
guage displays or messages will be displayed in Japanese.
3. Enter the password (i.e., the CLR and MON Keys). The mode display will
appear
MON
<PRG> BZ
CLR
3:ENG~JPN
Note The Programming Console is equipped with a password so that the
PC is operated only by qualified staff to ensure safe operation and
prevent accidents.
• After entering the password, Programming Console key operations
can be performed, the mode can be changed, and the display lan-
guage can be selected.
then the 1 Key after entering the password. Refer to 3-5 Buzzer Oper-
ation.
4. Press the CLR Key to move from the mode display to the initial display.
CLR
000000 CT**
Task No.
Note a) When the power is turned ON for the first time (before All Clear
has been performed), “CT” will be displayed as the task number.
b) The 3 Key can be pressed instead of the CLR Key to access the
initial display in the other language. Refer to the diagram on the
next page.
• When a memory error is displayed, press the CLR Key several times
to go to the initial display.
• To return to the mode display from the initial display, press the SHIFT
then CLR Keys.
SHIFT
<PRG> BZ
CLR
33
000000 CT**
3
Task No.
Note The password input, language selection, and initial displays can be switched
for CJ1/CJ1-H/CS1-H CPU Units as shown in the following diagram.
CJ1/CJ1-H/CS1-H CPU Units

connected.
<PRG> 3:ENG~JPN 3 <PRG> 3:JPN~ENG

PASSWORD! PASSWORD!
CLR MON CLR MON
<PRG> BZ <PRG> BZ
3:ENG~JPN 3:JPN~ENG
CLR 3 CLR Mode switched.

Mode switched.
SHIFT
000000 CT00 000000 CT00 CLR
SHIFT CLR
English displayed Japanese displayed
CLR CLR
000000 CT00 000000 CT00
34
Changing Operating Modes Section 3-2
3-2 Changing Operating Modes

The operating mode of the CPU Unit can be changed using the mode switch
on the Programming Console. The mode switch will be enabled after the
password has been accepted.
The mode switch can be changed from any screen.
CS1 CPU Units

RUN MONITOR PROGRAM
MONITOR MONITOR MONITOR
RUN PROGRAM RUN PROGRAM RUN PROGRAM
Mode display
<RUN> BZ <MON> BZ <PROGRAM> BZ
CLR SHIFT CLR
Initial display
000000 CT00

RUN MONITOR PROGRAM
MONITOR MONITOR MONITOR
RUN PROGRAM RUN PROGRAM RUN PROGRAM
Mode display (See note.) (See note.) (See note.)
<RUN> 3:JPN~ENG <MON> 3:JPN~ENG <PRG> 3:JPN~ENG
CLR SHIFT CLR
Initial display
000000 CT00
Note “3: JPNENG” indicates that Japanese language messages will be dis-
played. “3: ENGJPN” indicates that English language messages will be dis-
played. Press the 3 Key to change the display language.
!Caution Before changing the operating mode of the CPU Unit, make sure that doing so
will not affect other equipment.
35
Key Functions Section 3-3
Note 1. The CPU Unit is set by default so that the operating mode on the mode
switch of the connected Programming Console is used when power is
turned ON. The Programming Console mode will be used as long as the
default is set for the “Startup Mode” in the PC Setup (address +81 set to
PRCN).
2. If a Programming Console is not connected when power is turned ON and
the Startup Mode in the PC Setup is set to PRCN, a CS1 CPU Unit will au-
tomatically start in PROGRAM mode and a CJ1/CJ1-H/CS1-H CPU Unit
will automatically start in RUN mode.
3. The mode switch can be used to change the operating mode from any dis-
play without affecting the display. This is particularly useful during monitor-
ing, enabling the user to display monitoring details while changing the
operating mode. Hold down the SHIFT Key when changing the mode
switch.
3-3 Key Functions

The Programming Console has three key input modes. They are as follows:
• Normal input mode: Pressing the key alone
• Shift input mode: Pressing the SHIFT Key and then the key
• Text input mode: Pressing the TEXT Key and then the key
As indicated in the following diagram, keys are marked with input characters
for each of the 3 modes: Normal, shift, and text input.
Shift input Shift input
AR A
FUN Normal input HR Normal input 0 Normal input
A L 0
Text input Text input Text input
Normal Input Mode The shift input mode is used to enter the text in the center or lower-center of
the key.
Shift Input Mode The shift input mode is used to enter the text on the top of the key or on the
upper-left corner of the key. Shift mode is also used to input hexadecimal A to
F.
The key sequence to switch to shift input mode, and the shift input mode dis-
play are as follows:
^ The shift input mode mark

SHIFT can be reset by pressing
the SHIFT Key again.
• If a key is pressed when the shift input mode mark is being displayed, the
text at either the top or the upper-left corner of the key will be entered.
• Press the SHIFT Key again to return to the normal key input mode.
Text Input Mode The text input mode is used to enter the text (text or number) on the lower-
right corner of the key. The text input mode is used to enter file names when
Memory Cards are used.
The key sequence to switch to text input mode, and the text input mode dis-
play are as follows:
TEXT ! The text input mode

SHIFT mark can be reset by
!
pressing the CLR Key.
36
Clearing Memory Areas Section 3-4
• When the text input mode mark is displayed and a key is pressed, the text
or numeral on the lower-right corner of the key can be entered.
• Pressing the CLR Key to return to the normal key input mode.
Keypad The key layout of the CS1W-KS001-E Key Sheet is illustrated below.
,IR+ DR
FUN SFT NOT SHIFT
,IR IR
A B C D E F
TN ST TK ,–IR *EM AR
AND OR CNT TR WR/LR HR
G H I DISP J K L
AA AC EM CH CONT
LD OUT TIM DM *DM #
M N O P Q R
*EM_ CF
7 8 9 EM_/EXT CHG SRCH
7 8 9 S T U
E F
4 5 6 SET DEL MON
4 5 6 V W X
B C D
11 22 33 RESET INS ↑
Y Z
A TEXT
00 !
CLR VRFY WRITE ↓
3-4 Clearing Memory Areas

This operation is used to clear program memory and I/O memory and initialize
the PC Setup. The following two methods for clearing memory are possible.
The memory areas cleared in each method are as follows:
Memory clear Memory area
method Program I/O memory PC Setup
All clear Creates a task and Clears designated All PC Setup set-
writes the END memory areas. tings
instruction. (See (See note 3.)
note 2.)
Memory clear Clears from the Clears designated All PC Setup set-
designated program memory areas. tings.
address of the task (See note 3.)
currently being
edited (part of the
program.) (See
note 1.)
Note 1. If program address 000000 is designated, the program of the task currently
being edited will all be cleared.
2. The entire program will be cleared. After clearing the programs in all tasks,
either interrupt tasks and one cyclic task or just one cyclic task can be cre-
ated.
3. An address range within specific memory areas cannot be specified. All
data within the specified memory areas will be cleared.
When the All Clear or Memory Clear operation is executed, an END(001)
instruction will be written to the first address of the user ladder program.
NOP(000) instructions will not be written.
37
Specifying Memory Areas Not to be Cleared

Letters will be displayed at the bottom of the display for the memory areas that
will be cleared. If an area is specified to not be cleared, the corresponding let-
ter will disappear.
000000 CLR MEM?

CHWA TCDE P
Letters at the bottom of the display indicate the

memory areas that will be cleared.
Letter Areas to be cleared Key sequence
C CIO (See note)
CH
SHIFT
*DM
H HR (Holding bits)
AR
HR
W WR (Work bits)
*EM
WR/LR
A AR (Auxiliary bits)
AR
SHIFT
HR
T T (Completion Flags/PVs)
TIM
C C (Completion Flags/PVs)
TK
CNT
D DM (Data memory)
EM
DM
E EM (Extended data mem-

ory) SHIFT
EM Bank
DM number
P PC Setup CF
SHIFT SRCH
Note The CIO Area is used for I/O word data: I/O bits, Data Link bits, CS/CJ CPU
Bus Unit bits, Inner Board bits, SYSMAC BUS bits, I/O Terminal bits, Special I/
O Unit bits, CompoBus/D (DeviceNet) bits, and work bits. (Inner Board bits,
SYSMAC BUS bits, and I/O Terminal bits are supported by CS-series PCs
only.)
To clear the memory areas that are specified not to be cleared, repeat the
same key sequence. The appropriate letter will be displayed at the bottom of
the display.
The EM Area cannot be cleared if it has been converted to file memory. Refer
to Section 7 Memory Card Operations for information on formatting file mem-
ory and restoring the normal EM Area.
3-4-1 All Clear
RUN MONITOR PROGRAM
No No OK
38
This operation is used to clear (format) memory areas. When “All Clear” is
performed from the Programming Console, all programs in all tasks will be
cleared. One cyclic task is created, and the user can chose whether or not to
also create interrupt tasks.
Note The Programming Console cannot be used to create programs with more
than one cyclic task. Use the CX-Programmer if more than one cyclic task is
required.
Creating One Cyclic Task without Interrupt Tasks

Use the following procedure to clear memory and create one cyclic task
(CT00) and no interrupt tasks.
Note To create interrupt tasks, always select INT 1: YES when clearing memory. If
INT 0: NO is selected, you will not be able to create interrupt tasks unless you
clear memory again using INT 1: YES.
Key Sequence
Initial display NOT Specify exempt areas MON 0 0 MON

SET RESET
Operation Example
1,2,3... 1. Start the All Clear operation from the initial display.
000000 CT00
CLR
¡
000000CLR MEM ?
NOT
2. Specify the areas that are not to be cleared. Refer to page 38 for further
details on specifying the areas.
Example: Specifying the Counter Area to no be cleared.
TK 000000CLR MEM ?
CNT CHWA T DE P
Counter Area will not be cleared:

The "C" disappears.
To cancel "Counter Area will not be
cleared" press the TK/CNT Key once
more.
MON
000000CLR MEM ?
0:ALL 1:TASK
3. Select 0: ALL to clear all memory.
000000 CLR ALL ?

0
INT 0:NO 1:YES
4. Select INT 0: NO to create one cyclic task only (and no interrupts).
000000 CLR ALL ?

0
INT 0:NO
5. Start the All Clear operation.
39
MON
000000CLR'G MEM~
INT 0:NO
000000 CLR ALL

END 0:NO
• Press the CLR Key to return to the original display.
Creating One Cyclic Task and Interrupt Tasks
Use the following procedure to clear memory and create one cyclic task
(CT00) and interrupt tasks (IT001 to 003 and IT100 to 131).
Key Sequence
Initial display SET

NOT
RESET
Specify exempt areas MON 0 1 MON
Operation Example
1,2,3... 1. Start the All Clear operation from the initial display.
000000 CT00
CLR
¡
000000CLR MEM ?
NOT
details on specifying areas.
Example: Specifying the Counter Area not to be cleared.
TK 000000CLR MEM ?
CNT CHWA T DE P

The "C" disappears.
To cancel "Counter Area will not
be cleared" press the TK/CNT Key once
more.
MON
000000CLR MEM ?
0:ALL 1:TASK
3. Select 0: ALL to clear all memory.
000000 CLR ALL ?

0
INT 0:NO 1:YES
4. Select INT 1: YES to create interrupt tasks.
000000 CLR ALL ?

1
INT 1:YES
5. Start the All Clear operation.
MON
000000CLR'G MEM~
INT 1:YES
000000 CLR ALL

END 1:YES
40
Note When the All Clear operation is performed from the Programming
Console, cyclic task No. 0 will be automatically activated at PC star-
tup.
3-4-2 Memory Clear

RUN MONITOR PROGRAM
No No OK
This operation is used to clear the program in the current task starting with a
specified program address within the current task. It is also used to clear I/O
memory and the PC Setup.
Key Sequence
Specify exempt areas

Initial display NOT
SET RESET
MON 1 MON
Specify starting address for clear operation
Operation Example
1,2,3... 1. Start the Memory Clear operation.
Current Task No.
000000 CT00
CLR
¡
000000CLR MEM ?
NOT
details on specifying areas.
Example: Specifying the Counter Area to not be cleared.
TK 000000CLR MEM ?
CNT CHWA T DE P
The "C" disappears.
To cancel "Counter Area will not be
cleared" press the TK/CNT Key once
more.
3. Specify the first address to be cleared in the program.

Example: Clear the program starting from program address 000123 (in-
cluding 000123).
000123CLR MEM ?
1 2 3
CHWA T DE P
MON
000123CLR MEM ?
0:ALL 1:TASK
4. Select 1: TASK to clear the contents of the task.
000123CLR MEM ?
1
1:TASK
5. Execute Memory Clear.
MON
000123CLR'G MEM~
1:TASK
41
Buzzer Operation Section 3-5
000123CLR MEMEND
1:TASK
3-5 Buzzer Operation

RUN MONITOR PROGRAM
OK OK OK
This operation is used to turn ON and OFF the buzzer that sounds when Pro-
gramming Console keys are pressed. The buzzer ON/OFF operation is per-
formed from the mode display.
Key Sequence
Initial display SHIFT CLR SHIFT 1 SHIFT 1
Operation Example
1,2,3... 1. Access the buzzer mode display from the initial display.
CS/CJ-series PCs
000000 CT00
CLR
¡
CS1 CPU Units
SHIFT CLR <PROGRAM> BZ
Buzzer ON
<PRG> BZ
3:JPN~ENG
Buzzer ON
2. Turn the buzzer ON or OFF as desired.

CS1 CPU Units
SHIFT 1 <PROGRAM>
Buzzer OFF
<PRG>
3:JPN~ENG
Buzzer ON
Note a) When an error occurs, the buzzer will sound regardless of whether
the buzzer has been turned ON or OFF.
42
Selecting Tasks Section 3-6
b) The mode display is displayed immediately after the password has

been entered or after the mode is changed.
c) For CJ1/CJ1-H/CS1-H CPU Units, the display language can be
switched by pressing the 3 Key while “3: JPNENG” or “3:
ENGJPN” is being displayed.
3-6 Selecting Tasks

RUN MONITOR PROGRAM
OK OK OK
This operation allows the user to select the task and the type of task (cyclic or
interrupt.) From the Programming Console however, only interrupt task num-
bers 1,2, and 3 (IT100 to 131) can be newly created. Interrupt task numbers 0
and 4 to 99 (IT132 to 255) cannot be created.
Outline of Key Sequence for Selecting Tasks

0: CYCLE TASK
1: INTRPT
FUN CHG
FUN CHG
0 CLR 1 CLR
CYCLE TASK No.? INTRPT #?

00 000
Flashing
Flashing
Task No. WRITE Task No. WRITE
000000 CT00 000000 IT000
to
000000 IT255
Task Types and Task Numbers
Task Task No. Details Created using

the
Programming
Console
Cyclic tasks 0 to 31 Each enabled task is executed Task No. 0 only,
(See note in order of task number from cannot be cre-
1.) the lower number. Each ated. (1 to 31
enabled task is executed once can be cre-
each cycle from the first word ated.)
to the END(001) instruction.
43
Selecting Tasks Section 3-6
Task Task No. Details Created using

the
Programming
Console
Interrupt Power OFF 1 Executed when power to the Possible
tasks interrupt CPU Unit is interrupted.
(See note Scheduled 2, 3 Executed at regular intervals Possible
2.) interrupt according to the CPU Unit’s
internal timer.
I/O inter- 100 to Executed when the Interrupt Possible
rupt 131 Input Unit input turns ON.
External 0 to 255 Executed when there is a Task No. 1 to 3
interrupt request from a Special I/O and 100 to 131
Unit, a CS1 CPU Bus Unit, or possible. (0.4 to
the Inner Board user program. 99 and 132 to
255 not possi-
ble.)
Note 1. The Programming Console cannot be used to create programs with more
than one cyclic task. Use the CX-Programmer if more than one cyclic task
is required.
2. If INT 0: NO is set when memory is cleared, only a cyclic task (CT00) can
be created, and interrupt tasks cannot be created. Refer to page 39 for de-
tails.
Cyclic Task
Key Sequence
Initial display FUN CHG 0 Task No. WRITE
Operation Example
1,2,3... 1. Access the task selection display from the initial display.
000000 CT00
CLR
¡
000000
FUN
FUN (???)
0:CYCLE TASK
CHG
1:INTRPT
2. Select 0: CYCLE TASK from the above display.
0
CYCLE TASK No.?
00
Flashing
3. Input the task number.
4. Confirm the task number and then press the WRITE Key to set the task
number and return to the initial display.
000000 CT00
WRITE
44
I/O Table Operations Section 3-7
Interrupt Tasks
Key Sequence
Initial display FUN CHG 1 Task No. WRITE
Operation Example
1,2,3... 1. Access the task selection display from the initial display.
000000 CT00
CLR
¡
000000
FUN
FUN (???)
0:CYCLE TASK
CHG
1:INTRPT
2. Select 1: INTRPT from the above display.
INTRPT #?
1
000
Flashing
3. Enter the number of the interrupt task.
INTRPT #?
1 2 3
123
4. Confirm the task number and then press the WRITE Key to set the number.
000000 IT123
WRITE
3-7 I/O Table Operations

3-7-1 I/O Table Create
RUN MONITOR PROGRAM
No No OK
This operation is used to register the I/O tables in the CPU Unit. The I/O
tables contain information on all Units mounted to the CPU and Expansion
Racks. The information includes the unit types and positions.
Key Sequence
0
CH
Initial display FUN SHIFT CHG 9 7 1 3 WRITE
*DM
1
Password
45
Operation Example
1,2,3... 1. From the initial display, access the I/O Table Create display and start the I/
O table creation process.
000000 CT00
CLR
¡
FUN SHIFT
CH
000000I/O TBL ?
*DM
Rack 1st Word En
(See note.)
000000I/O TBL
CHG
WRIT ????
Note If the first word for a Rack has been set in advance from the CX-Pro-
grammer for a CS1-H or CJ1-H CPU Unit, “Rack 1st Word En” will be
displayed to show that the first word has been set.
2. Enter the password (9713) and then press the WRITE Key.
000000I/O TBL
9 7 1 3
WRIT 9713
Note “9713” is the password set by the system for I/O Table Create and
Memory Card Format operations. This password cannot be changed.
000000CPU BU ST?
WRITE
0:CLR 1:KEEP
3. Select to either clear or keep CS1 CPU Bus Unit system information.
000000I/O TBL
0 1
WRIT OK
0 : Clears all CS/CJ CPU Bus Unit system information.
1 : Keeps all CS/CJ CPU Bus Unit system information.
4. Return to the initial display.
000000 CT00
CLR
Confirming Rack First With a CS1-H or CJ1-H CPU Unit, the Programming Console can be used to
Word Settings check whether or not the first word has been set on a Rack. Use the following
procedure.
1,2,3... 1. Press the FUN, SHIFT, and CH Keys to start the I/O table creation opera-
tion. If the first word for a Rack has been set, a message saying so will ap-
pear on the second line of the display.
SHIFT
CH 000000I/O TBL ?
FUN
*DM Rack 1st Word En
If nothing is displayed, then the first word has not been set.
2. Press the CHG Key, enter the password (9713), and then press the
WRITE Key to continue creating the I/O tables, or press the CLR Key to
cancel the operation and return to the initial display.
46
Note Detailed Information on I/O Table Creation Errors

The CS1-H and CJ1-H CPU Units will provide detailed information on errors
that occur when creating I/O tables. For example, with a CS1-H CPU Unit, the
contents of A261 will provide information on the Unit causing the error when-
ever one occurs when creating the I/O tables from the Programming Console.
For details, refer to the troubleshooting section in the CS Series
Programmable Controllers Operation Manual or CJ Series Programmable
Controllers Operation Manual.
I/O Table Error Details
Name Address Contents When At Setting
Word Bit changing startup timing
to RUN
mode
CPU Bus Unit A261 00 ON: Error in CPU Bus Held Cleared When I/O
Setup Area Ini- Unit Setup tables are
tialization Error Turns OFF when I/O created
Flag tables are generated
normally.
I/O Overflow 02 ON: Overflow in maxi-
Flag mum number of I/O
points.
Turns OFF when I/O
tables are generated
normally.
Duplication 03 ON: The same unit
Error Flag number was used
more than once.
Turns OFF when I/O
normally.
I/O Bus Error 04 ON: I/O bus error
Flag Turns OFF when I/O
normally.
SYSMAC BUS 06 ON: SYSMAC BUS
Recognition detection ended in an
Error Flag error.
Turns OFF when I/O
normally.
Special I/O Unit 07 ON: Error in a Special
Error Flag I/O Unit
Turns OFF when I/O
normally.
I/O Uncon- 09 ON: I/O detection has
firmed Error not been completed.
Flag Turns OFF when I/O
normally.
47
3-7-2 I/O Table Verify

RUN MONITOR PROGRAM
OK OK OK
This operation is used to compare the I/O table registered in the PC (regis-
tered I/O tables), with the actual I/O Units mounted to the PC Racks.
Key Sequence
CH
Initial display FUN SHIFT VRFY VRFY
*DM
...
Operation Example
1,2,3... 1. From the initial display, execute I/O Table Verify.
000000 CT00
CLR
¡
SHIFT
CH 000000I/O TBL ?
FUN
*DM
2. Confirm the location of any verification errors.
VRFY
000000I/O VRFY
RAK1 SLOT10
Rack No. Slot No.
3. Any further errors will be displayed in sequence as the VRFY Key is

pressed.
VRFY
000000I/O VRFY
RM0 RT2 SLOT10
Master Slot No.

Slave
VRFY
000000I/O VRFY
CPU BU No.10
No. of CS1 CPU Bus Units
(CPU Bus Units)
VRFY
000000I/O VRFY
RM4 OPTCL23(H)CH
Master High/Low
Word allocated bits
to Optical I/O
4. When all verification errors have been displayed, the following display will
appear.
VRFY
000000I/O VRFY
END
Verification complete
48
Verification Errors
Verification Error The following display indicates that the mounted I/O Units differ from those
registered in the I/O table.
000000I/O VRFY
RAK1 SLOT10
Rack No. Slot No.
No. of Remote Terminals The following display indicates that the number of Slaves (RT) connected to
Verification Error the Master does not match the number registered in the I/O table.
000000I/O VRFY
RM1 CONECT RT
Master
C200H/C500 Master The following display indicates that the Master Unit (RM) (C200H/C500)
Verification Error mounted to the PC does not match the one registered in the I/O table.
000000I/O VRFY
RM1 C200H/C500
Master
Master-Slave Slot The following display indicates that a Slave Unit connected to a Master does
Verification Error not match the Unit registered in the I/O table.
000000I/O VRFY
RM7 RT5 SLOT10
Master Slave Slot No.
Slaves Connected to The following display indicates that the words or the high/low word specifica-
Master Verification Error tion allocated to an Optical I/O Units does not match the information regis-
tered in the I/O table.
000000I/O VRFY
RM7 OPTCL31(L)CH
Master High/Low
word
Word allocated to
Optical I/O
No. of Output Words The following display indicates that the number of output words connected to
Verification Error a Master mounted to the PC does not match the number registered in the I/O
table.
000000I/O VRFY
RM1 No.9 UNITOUT
Master Allocated word
49
No. of Input Words The following display indicates that the number of input words connected to a
Verification Error Master mounted to the PC does not match the number registered in the I/O
table.
000000I/O VRFY
RM1 No.9 UNITIN
Master Allocated word
CS1 CPU Bus Unit The following display indicates that the type of a CS/CJ CPU Bus Unit (CPU
Verification Error Bus Unit) mounted to the PC does not match the type registered in the I/O
table.
000000I/O VRFY
CPU BU No.31
Unit number of
CPU Bus Unit
50
SECTION 4
Writing and Editing Programs
This section describes how to create and edit programs from the Programming Console.
4-1 Inputting Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

4-1-1 Procedure for Inputting Instructions. . . . . . . . . . . . . . . . . . . . . . . . . 52
4-1-2 Inputting Basic Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
4-1-3 Inputting Timer/Counter Instructions: TIM/CNT. . . . . . . . . . . . . . . 57
4-1-4 Inputting Special Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
4-2 Reading and Searching Programs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
4-2-1 Reading Designated Addresses. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
4-2-2 Instruction Search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
4-2-3 Bit Search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
4-3 Editing Programs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
4-3-1 Instruction Change . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
4-3-2 Instruction Insert. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
4-3-3 Instruction Delete . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
4-3-4 Bit Address Change . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
4-3-5 N.O./N.C. Change. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
4-3-6 Instruction Variation Change . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
4-3-7 Timer/Counter SV Changes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
51
Inputting Instructions Section 4-1
4-1 Inputting Instructions

4-1-1 Procedure for Inputting Instructions
RUN MONITOR PROGRAM
No No OK
Programs can be input in PROGRAM mode only.
1,2,3... 1. Press the FUN and CHG Keys to switch tasks and bring up the initial dis-
play.
Switch tasks
FUN CHG
000000 CT00 000000 IT000

Initial display
↓ ↓
000000 CT00 000000 IT000

END(001) END(001)
↓ ↑ ↑ ↓
000001ADR OVER 000001ADR OVER
• The END(001) instruction will be displayed at program address

000000 the first time instructions are written into a task. When the
END(001) instruction is displayed, all instructions input will be inserted
before the END(001) instruction.
• If the address after the END(001) instruction is displayed, ADR OVER
will appear. Instructions cannot be executed, even if they are input
while ADR OVER is displayed, so press the Up Key to return to the
END(001) instruction display.
2. Input instructions while the END(001) instruction is displayed.
000000 CT00
↓ ↑
END(001)
a) Input LD 000100.
AA 000000
1 0 0
LD LD 000100
000001 CT00
WRITE
END(001)
52
b) Press the WRITE Key.

Write will be displayed temporarily. When inputting is complete, the
address will move forward by one and the END(001) instruction will au-
tomatically be sent to the next address.
3. Input OUT 000200 while the END (001) instruction is displayed.
AC 000001
2 0 0
OUT OUT 000200
000002 CT00
WRITE
END(001)
4. Check instructions that have been input correctly.
000001 CT00
↑
OUT 000200
000000 CT00
↑
LD 000100
An instruction can be input when any program address is displayed. The
instruction will overwrite the data at the current program address.
5. Return to the initial display.
000000 CT00
CLR
4-1-2 Inputting Basic Instructions

RUN MONITOR PROGRAM
No No OK
Basic instructions can be input only when the CPU Unit is in PROGRAM
mode.
Key Sequence
Mnemonic Operand WRITE
Operation Example Use the following procedure to input the LOAD (LD) instruction.
1,2,3... 1. Designate the mnemonic and the operand.
AA 000200
2
LD LD 000002
2. Press the WRITE Key.
000201 CT00
WRITE
END(001)
If a mistake is made inputting, press the Up Key to bring up the program
address, and re-input the instruction. The data at the address will be over-
written.
53
Inputting Basic Instructions

Mnemonic Key sequence Mnemonic Key sequence
LD OR LD
AA ST AA
LD OR LD
LD NOT AND LD
AA TN AA
NOT
LD AND LD
OR OUT
ST AC
OR OUT
OR NOT OUT NOT

ST AC
NOT NOT
OR OUT
AND SET
TN
FUN
AND SET
AND NOT RSET

TN
NOT FUN
AND RESET
Designating Bit Addresses

Bit type Key sequence Display example
CIO bits Bit 15 of CIO 0000
Number
000000
LD 000015
Work bits (WR) Bit 15 of W000
*EM Number
WR/LR
000000
LD W00015
Holding bits (HR) Bit 15 of H000
AR
HR Number
000000
LD H00015
Auxiliary bits (AR) Bit 15 of A000
AR
SHIFT Number
HR
000000
LD A00015
Timer bits T0015
TIM Number
000000
LD T0015
Counter bits C0015
TK
CNT Number
000000
LD C0015
54

Clock pulse/Condition Always ON Flag
CF
Flag SHIFT
SRCH
000000
LD ON
When clock pulses or

Condition Flags are Display Bit
designated, the bits listed at ON Always ON Flag
the right can be designated,
by using the Up and Down OFF Always OFF Flag
Keys. AER Access Error Flag
0.02s 0.02-s clock pulse
1s 1-s clock pulse
1min 1-min clock pulse
ER Error Flag
CY Carry Flag
> Greater Than Flag
= Equals Flag
< Less Than Flag
N Negative Flag
OF Overflow Flag
UF Underflow Flag
>= Greater Than or Equals Flag
<> Not Equal Flag
<= Less Than or Equals Flag
Task Flag TK0000

TK
SHIFT Number
CNT
000000
LD TK0000
Designating Index Register Addresses

Method Key sequence Display example
Direct addressing IR10
DR
Number
IR
(Absolute address) 000201 MOVL

SV A IR10
Note Only some instructions
such as MOVL are pos -
sible.
Indirect addressing IR10

,IR+
,IR Number
(Relative address) 000201
LD ,IR10
55
Method Key sequence Display example

Constant offset +1234, IR10
,IR+
addressing Number
,IR
(Relative 000201
address) LD +1234,IR10
(+) Positive offset
SET
Number –1234, IR10
RESET (Constant offset) 000201

(–)
LD -1234,IR10
Negative offset
DR offset ,IR+ DR 01, IR10

addressing Number
,IR
000201
(Relative address)
LD DR01,IR10
DR
SHIFT Number
IR
DR address
Auto-increment Auto-increment+ IR10+

,IR+
SHIFT Number 000201
,IR
(Relative LD ,IR10+
address)
Auto-increment (+1)
Auto-increment+2 IR10++
,IR+ ,–IR
SHIFT
,IR
SHIFT
TR
Number 000201
LD ,IR10++
Note The display will toggle
between auto-incre- Auto-increment (+2)
ment +1 and auto-in-
crement +2.
Auto-decrement Auto-decrement IR10–

,–IR
SHIFT
TR
Number 000201
LD ,-IR10
(Relative address)
Auto-decrement (–1)
Auto-decrement+2 IR10– –
,–IR ,–IR
SHIFT
TR
SHIFT
TR
Number 000201
LD ,--IR10
Note The display will toggle Auto-decrement (–2)
between auto-decre-
ment –1 and auto-
decrement –2.
56
Designating Instruction Variations

Variation Key sequence Display example
Differentiate up
SHIFT
SET
000123 CT00
@LD 000000
Note The same key
sequence can be Symbol: Differentiate up
used to reset.
Differentiate down
SHIFT 000123 CT00
RESET
%LD 000000
Note The same key se-
quence can be used Symbol:
to reset. Differentiate down
Immediate refresh
TEXT
000123 CT00
!
!LD 000000
quence can be used Symbol: Immediate refresh
to reset.
000123 CT00
!@LD 000000
Symbols: Immediate
refresh/Differentiate up
000123 CT00
!%LD 000000
Symbols: Immediate
refresh/Differentiate down
4-1-3 Inputting Timer/Counter Instructions: TIM/CNT

RUN MONITOR PROGRAM
No No OK
Timer/counter instructions can be input when the CPU Unit is in PROGRAM

mode.
Key Sequence
TK
CNT
TC number SV WRITE
TIM
Operation Example The following example describes how to input TIM 0010 with a SV of 10 s.
1,2,3... 1. Press the TIM Key and input the timer number.
000201 CT00
TIM 1 0
TIM 0010
000201 TIM
↓ SV #0000
2. Input the set value. In the following example, the set value is #0100 (10 s).
000201 TIM
1 0 0
SV #0100
57
3. Press the WRITE Key.
000202 CT00
WRITE
END(001)
If a mistake is made inputting the set value, press the Up Key until the set
value is displayed. Then press the CONT/# Key and enter the correct val-
ue.
Inputting Timer/Counter Instructions

Instruction Key sequence
TIM
TIM
CNT
TK
CNT
Designating Timer/Counter Set Values (1)

Designating Constants
Type Key sequence Display example
Constants #0123
CONT
Number
#
000201 TIM
SV #0123
Designating Words (16-bit data)

CIO words CIO 0010
CH
SHIFT Number
*DM
000000 TIM
SV 0010
Work words (WR) W010
*EM
Number
WR/LR
000201 TIM
SV W010
Holding words (HR) H010
AR
Number
HR
000201 TIM
SV H010
Auxiliary words (AR) A010
AR
SHIFT
HR
Number
000201 TIM
SV A010
Data memory words D00010
EM
(DM) DM
Number
000201 TIM
SV D00010
Extended DM (EM): *EM_ E0_00010
With bank EM_/EXT
Number
000201 TIM
(Bank number, SV E0_00010
word address)
58

Extended DM (EM): E00010
EM
Current bank SHIFT Number
DM
000201 TIM
(Word address) SV E00010
Timer PVs T0010
TIM Number
000201 TIM
SV T0100
Counter PVs C0010
TK
Number
CNT
000201 TIM
SV C0010
Designating Timer/Counter Set Values (2)

Designating Indirect DM/EM Addresses
Mode Key sequence Display example
Data Registers DR10
DR Number
(DR) SHIFT
IR
000201 TIM
SV DR10
Indirect DM Addresses
BCD *D00010
CH
Number
*DM
000202 TIM
SV *D00010
Binary @D00010
CH CH
Number
*DM *DM
000202 TIM
SV @D00010
Indirect EM Addresses
BCD
*E0_00010
With bank *EM_
SHIFT Number
EM_/EXT 000202 TIM
SV *E0_00010
BCD *E00010
*EM
WR/LR
000202 TIM
SV *E00010
Binary
*EM_ *EM_ @E0_00010
With bank SHIFT EM_/EXT
SHIFT EM_/EXT
Number
000202 TIM
SV @E0_00010
Binary E00010
*EM *EM
Current bank SHIFT SHIFT Number
WR/LR WR/LR
000202 TIM
SV @E00010
59
In BCD mode, indirect DM/EM addresses can be specified from D00000

to D09999 and E00000 to E09999. Use binary mode to specify D10000 to
D32767 and E10000 to E32767.
If 8000 to FFFF Hex are specified as indirect DM addresses in binary
mode, E00000 to E32767 in bank 0 of the EM Area will be designated.
If 8000 to FFFF Hex are specified as indirect EM addresses in binary
mode, E00000 to E32767 in the bank following the one specified will be
designated.
4-1-4 Inputting Special Instructions
RUN MONITOR PROGRAM
No No OK
Special instructions can be input when the CPU Unit is in PROGRAM mode.
Inputting Standard Special Instructions
Key Sequence
FUN Function code ↓ Operand ↓ Operand WRITE
Operation Example The following example describes how to input the MOV(021) instruction.
1,2,3... 1. Press the FUN Key, enter the function code, and then press the Down Key.
All 3 digits of the function code must be input. In this example, the function
code for MOV is 021.
000202
FUN
FUN (???)
000202
0 2 1
MOV(021)
000202 MOV
↓ WRITE
SV A 0000
or
2. Input the first operand (SV A), and press the Down Key. In this example,
constant #0100 (hexadecimal) is input.
CONT 000202 MOV

1 0 0
# SV A #0100
000202 MOV
↓ WRITE
SV B 0000
or
3. Input the next operand (SV B), and press the WRITE Key. In this example,
CIO 0010 is input.
CH 000202 MOV
SHIFT
*DM 1 0
SV B 0010
000203 CT00
WRITE
END(001)
• The function codes for some of the instructions, such as KEEP and
STEP (which have operands), will not be displayed.
60
• For further information of the following instruction variations, refer to

page 100.
Inputting Symbol Comparison Instructions

Key Sequence
FUN Function code Logic Operand Operand WRITE
Operation Example The following example describes how to input the <= instruction.
1,2,3... 1. Press the FUN Key and enter the function code. The function code for <=
is 318.
000202
FUN
FUN (???)
000202
3 1 8
[LD] <=SL(318)
2. Specify the logic type. In this example, OR.
ST 000202
OR [OR] <=SL(318)
3. Press the Down Key.
000202 <=SL
↓ WRITE
SV A 0000
or
4. Input the first operand (SV A), and press the Down Key. In this example,
constant #00000010.
CONT 000202 <=SL

1 0
# SV A #00000010
000202 <=SL
↓ WRITE
SV B 0000
or
5. Input the next operand (SV B), and press the WRITE Key. In this example,
CIO 0011 is used.
000202 <=SL
1 1
SV B 0011
000203 CT00
WRITE
END(001)
61
Designating Word (16-bit) Addresses

CIO words CIO0010
CH
SHIFT Number
*DM
000000 MOV
SV A 0010
Work words (WR) W010
*EM
WR/LR
Number
000000 MOV
SV A W010
Holding words (HR) H010
AR
HR Number
000000 MOV
SV A H010
Auxiliary words (AR) A010
AR
SHIFT
HR
Number
000000 MOV
SV A A010
Data memory words D00010
EM
(DM) Number
DM
000000 MOV
SV A D00010
Extended DM (EM): E0_00010
*EM_
With bank Number
EM_/EXT
000000 MOV
(Bank number,
word address) SV A E0_00010
Extended DM (EM): E00010
EM
DM
000000 MOV
(Word address)
SV A E00010
Timer PVs T0010
TIM Number
000000 MOV
SV A T0100
Counter PVs C0010
TK
Number
CNT
000000 MOV
SV A C0010
Data Registers (DR) DR10
DR Number
SHIFT
IR
000000 MOV
SV A DR01
Index Registers (IR) IR1
DR
IR Number
000000 MOVL
SV A IR01
62
Designating Indirect DM/EM Addresses

Indirect DM Addresses
BCD *D00010
CH
*DM
Number
000202 MOV
SV A *D00010
Binary @D00010
CH CH
Number
*DM *DM
000202 MOV
SV A @D00010
Indirect EM Addresses
BCD *E0_00010
*EM_
With bank SHIFT Number
EM_/EXT
000202 MOV
SV A *E0_00010
BCD *E00010
*EM
Current bank SHIFT
WR/LR
Number
000202 MOV
SV A *E00010
Binary @E0_00010
*EM_ *EM_
With bank SHIFT
EM_/EXT
SHIFT
EM_/EXT
Number
000202 MOV
SV A @E0_00010
Binary @E00010
*EM *EM
Current bank SHIFT SHIFT Number
WR/LR WR/LR
000202 MOV
SV A @E00010
In BCD mode, indirect DM/EM addresses can be specified from D00000

to D09999 and E00000 to E09999. Use binary mode to specify D10000 to
D32767 and E10000 to E32767.
If 8000 to FFFF Hex are specified as indirect DM addresses in binary
mode, E00000 to E32767 in bank 0 of the EM Area will be designated.
If 8000 to FFFF Hex are specified as indirect EM addresses in binary
mode, E00000 to E32767 in the bank following the one specified will be
designated.
63
Designating Constants
Single-word constants
CONT
Number
000202 MOV
#
SV A #1234
4-digit hexadecimal
Hexadecimal
Long constants
CONT
Number 000202 MOVL
#
SV A #12345678
8-digit hexadecimal
Hexadecimal
The display format of constants can be changed by pressing the,–IR/TR Key.
CONT Number
#
000202 MOV
#
SV A #FFFF
,–IR
TR
Hexadecimal
DISP
+ 000202 MOV
(–) SV A -1
,–IR Signed decimal
TR
DISP
000202 MOV
&
SV A &65535
,–IR
TR Unsigned decimal
DISP
When the signed decimal display is used, the value can be changed between
positive and negative using the SET/RESET Keys.
000202 MOV
SV A +4660
Positive SET
RESET
000202 MOV
SV A -4660
Negative
Note Changes such as those illustrated above cannot be made for BCD data con-
stants such as Timer/Counter set values, JMP/Subroutine numbers etc.
Designating Instruction Variations
Differentiate up
SHIFT 000123 CT00
SET
@MOV(021)
quence can be used to
reset.
Symbol: Differentiate up
64
Reading and Searching Programs Section 4-2

Differentiate down
SHIFT 000123 CT00
RESET
%SET 000000
quence can be used
to reset. Symbol: Differentiate down
Immediate refresh
TEXT 000123 CT00
!
!MOV(021)
quence can be used to
reset. Symbol: Immediate refresh
000123 CT00
!@MOV(021)
Symbols: Immediate refresh/Differentiate up

000123 CT00
!%SET 000000
Symbols: Immediate refresh/Differentiate down
4-2 Reading and Searching Programs

4-2-1 Reading Designated Addresses
RUN MONITOR PROGRAM
OK OK OK
This operation is used to read programs from user memory. In RUN and
MONITOR modes, the I/O status of the current bit will be displayed.
Key Sequence
↓
Initial display Program address ↓
↑
Operation Example In the following example, address 123456 is read.
1,2,3... 1. From the initial display, specify the address to be read. In this example, pro-
gram address 123456 is read.
000000 CT00
CLR
¡
123456
1 2 3 4 5 6
123456 CT00
↓ LD 000000
The program address is displayed when using either the Instruction
Search or Operand Search operation.
2. Using the Up and Down Keys, read the previous and next program ad-
dresses.
65
123457 CT00
↓ AND 002100
123456 CT00
↑
LD 000000
When the program is finished, the following display will appear.
123458 CT00
↓ END(001)
If you attempt to read program addresses after the END(001) instruction,
(program addresses without instructions) ADR OVER will be displayed.
When there is no END(001) instruction, the following display will appear.
123459ADR OVER
4-2-2 Instruction Search

RUN MONITOR PROGRAM
OK OK OK
This operation is used to search the program for specified instructions. The
program address from which to begin the search can be specified before
starting.
Key Sequence
CF CF CF
Initial display Mnemonic SRCH SRCH SRCH
Operation Example The following example shows a search for the LD (LOAD) instruction.
1,2,3... 1. From the initial display, specify the instruction to be searched for and press
the CF/SRCH Key to execute. This example shows a search for LD
000100.
000000 CT00
CLR
AA 000000
1 0 0
LD LD 000100
CF 000100SEARCH'G
SRCH LD 000100
The next LD instruction after the beginning program address will be dis-
played.
000200 CT00 FIND

LD 000100
2. To continue searching for the same instruction, press the CF/SRCH Key.
The following display will appear.
CF 000300 CT00 FIND

SRCH LD 000100
66
3. When the search reaches the END(001) instruction, the following display
will appear.
CF 000400 CT00 FIND

SRCH END(001)
4. If the SRCH Key is pressed after the search has finished searching to the
END(001) instruction, the following display will appear.
CF 000400 CT00 FIND

SRCH NO END INST END
4-2-3 Bit Search

RUN MONITOR PROGRAM
OK OK OK
This operation searches for the program for a designated bit address. The
program address from which to begin the search can be specified before
starting.
Key Sequence
CF CF CF
Initial display Bit address SRCH SRCH SRCH
Operation Example In the following example, A20011 is searched for.
1,2,3... 1. From the initial display, specify the bit address to be searched for and press
the CF/SRCH Key to execute. This example shows a search for A20011.
000000 CT00
CLR
¡
CONT AR 000000 CT00

SHIFT SHIFT 2 0 0 1 1
# HR BIT A20011
CF 000000SEARCH'G
SRCH BIT A20011
The following display will appear.
000020 CT00 BIT

LD A20011
2. To continue searching for the same address, press the CF/SRCH Key. The
following display will appear.
CF 000300 CT00 BIT

SRCH AND A20011
CF 000319 CT00 BIT

SRCH OR N A20011
3. When the search reaches the END(001) instruction, the following display
will appear.
CF 000400 CT00 BIT

SRCH END(001)
67
4. If the SRCH Key is pressed after the search has finished searching to the
END(001) instruction, the following display will appear.
CF 000400 CT00 BIT

SRCH NO END INST END
Designating Bit Addresses

CONT
SHIFT
#
Number
000000
BIT 000015
Work bits Bit 15 of W000
CONT *EM
(WR) SHIFT Number
# WR/LR
000000
BIT W00015
Holding bits Bit 15 of H000
CONT AR Number
(HR) SHIFT
# HR
000000
BIT H00015
Auxiliary bits Bit 15 of A000
CONT AR
(AR) SHIFT SHIFT Number
# HR
000000
BIT A00015
Timer bits T00015
CONT
SHIFT TIM Number
#
000000
BIT T0015
Counter bits C0015
CONT TK
SHIFT
# CNT
Number
000000
BIT C0015
68
Editing Programs Section 4-3

Clock pulse/ Always ON Flag
CF
Condition SHIFT
SRCH
Flag 000000
BIT ON
When clock pulses or Condition

Display Bit
Flags are designated, the bits
listed at the left can be designated, ON Always ON Flag
by using the Up and Down Keys. OFF Always OFF Flag
AER Access Error Flag
1s 1-s clock pulse
ER Error Flag
CY Carry Flag
> Greater Than Flag
= Equals Flag
< Less Than Flag
N Negative Flag
OF Overflow Flag
UF Underflow Flag
<> Not Equal Flag
Task Flag TK0000

TK
SHIFT
CNT
Number
000000
BIT TK0000
4-3 Editing Programs

4-3-1 Instruction Change
RUN MONITOR PROGRAM
No No OK
This operation is used to overwrite instructions in user programs.
Key Sequence
Program address display Input mnemonic WRITE
Operation Example In the following instruction block, the instruction for address 000200 will be
changed to LD NOT 000002.
Address Instruction Operand
: : :
000200 LD 000001 Changed to LD NOT 000002.
000201 AND 000200
: : :
69
1,2,3... 1. From the initial display, access the address where the instruction is to be
changed.
000000 CT00
CLR
¡
000200 CT00
2 0 0 ↓ LD 000001
2. Input the instruction and press the WRITE Key.
AA 000201 CT00
NOT 2 WRITE
LD AND 000200
3. Press the Up Key to check the instruction.
000200 CT00
↑
LD N 000002
4-3-2 Instruction Insert

RUN MONITOR PROGRAM
No No OK
This operation is used to insert instructions into the user program.
Key Sequence
Program address display Input mnemonic INS
Operation Example In the following instruction block, AND 000100 will be inserted at address
000201.
: : :
000200 LD 000001
AND 000100 will be inserted.
000201 AND 000200
: : :
1,2,3... 1. From the initial display, access the address where the instruction is to be
inserted.
000000 CT00
CLR
¡
000201 CT00
2 0 1 ↓ AND 000200
2. Specify the instruction to be inserted, and press the WRITE Key.
000201 INS?
AND 1 0 0 INS
AND 000100
3. Press the Down Key to insert the designated instruction. The next program
address will be displayed.
000202 INS END

↓ AND 000200
70
If the user attempts to insert an instruction at an address where no instruc-

tion exists, ADR OVER will be displayed, and the instruction will not be in-
serted.
↑ 000201 CT00
AND 000100
4-3-3 Instruction Delete

RUN MONITOR PROGRAM
No No OK
This operation is used to delete instructions from the user program.
Key Sequence
Program address display DEL

↑
Operation Example In the following instruction block, AND 000200 will be deleted from address
00201.
: : :
000200 LD 000001
000201 AND 000200 Delete
000202 OUT 000100
: : :
1,2,3... 1. From the initial display, access the address of the instruction to be deleted.
000000 CT00
CLR
¡
000201 CT00
2 0 1 ↓ AND 000200
2. Delete the instruction.
000201 DEL?
DEL
AND 000200
3. Press the Up Key to delete the instruction currently displayed. The next
program address will move forward.
000201 DEL END

↑
OUT 000100
• If the user attempts to delete from an address where there is no in-
struction or when END(001) instruction is written, ADR OVER will be
displayed.
• When multiple-operand instructions are deleted, the set values (oper-
ands) will also be deleted.
4-3-4 Bit Address Change

RUN MONITOR PROGRAM
No No OK
71
This operation is used to change bit addresses in operands in the user pro-
gram.
Key Sequence
Program address display Input operand address WRITE
Operation Example In the following instruction block, the operand address at 000200,
CIO 000001, will be changed to CIO 000002.
Address Instruction Operands
: : :
000200 LD 000001 The operand address will be changed to
000201 AND 000200 CIO 000002.
: : :
1,2,3... 1. From the initial display, access the address of the instruction containing the
bit address to be changed.
000000 CT00
CLR
¡
000200 CT00
2 0 0 ↓ LD 000001
2. Specify the new operand, and press the WRITE Key.
000200 CT00
2
LD 000002
000201 CT00
WRITE
AND 000200
3. Press the Up Key to check the operand has been changed.
000200 CT00
↑
LD 000002
4-3-5 N.O./N.C. Change

RUN MONITOR PROGRAM
No No OK
This operation is used to change N.O. and N.C. conditions in the user pro-
gram.
Key Sequence
Program address display NOT NOT WRITE
Operation Example In the following instruction block, address 000200 will be changed from LD
000001 to LD NOT 000001.
: : :
72
000201 AND 000200

: : :
1,2,3... 1. From the initial display, access the address containing the instruction to be
changed.
000000 CT00
CLR
¡ LD 000000
000200 CT00
2 0 0 ↓ LD 000001
2. Press the NOT Key and then the WRITE Key.
000200 CT00
NOT
LD N 000001
000201 CT00
WRITE
AND 000200
3. Use the Up Key to check that LD has been changed to LD NOT.
000200 CT00
↑
LD N 000001
4-3-6 Instruction Variation Change

RUN MONITOR PROGRAM
No No OK
This operation is used to change the variation of an instruction in the user pro-
gram. Refer to page 108 for further information on key sequences and dis-
plays in MONITOR mode.
Key Sequence
Differentiate up
Program address display WRITE
SHIFT
SET
Differentiate down
SHIFT
RESET
Immediate refresh
TEXT
!
Operation Example In the following instruction block address, 000200 (LD000001) will be changed
to an upwardly differentiated LD instruction.
: : :
000200 LD 000001 Changed to LD 000001.
000201 AND 000200
: : :
1,2,3... 1. From the initial display, access the address of the instruction to be
changed.
73
000000 CT00
CLR
¡
000200 CT00
2 0 0 ↓ LD 000001
2. Using the following key sequence, specify the variation and press the
WRITE Key.
SHIFT
000200
SET
@LD 000001
000201 CT000
WRITE
AND 000200
3. Use the Up Key to check that the variation has changed.
000200 CT00
↑
@LD 000001
4-3-7 Timer/Counter SV Changes

RUN MONITOR PROGRAM
No No OK
Timer/Counter SV Change 1: Constant or Word

This operation is used to change the set value of a timer/counter in the user
program.
Key Sequence
Designated constant
Timer/counter SV display CHG WRITE
Designated word
Operation Example The following example describes how to change the set value for TIM 0001.
1,2,3... 1. From the initial display, access the timer/counter instruction for which the
set values will be changed.
000000 CT00
CLR
¡
CF 000201 CT00 FIND

TIM 1 SRCH TIM 0001
000201 TIM
↓ SV #0100
2. Star the set Timer/Counter SV Change 1 operation.
000201SV ?
CHG
#0100
3. The designated word or constant specified for the set value can be
changed from the above display.
74
Changing a Constant
Input the constant as follows:
CONT 000201SV ?
1 2 0
# #0120
000201 TIM
WRITE
SV #0120
Changing a Word Address
Input the word address as follows:
CH 000201SV ?
SHIFT
*DM 1 0
0010
000201 TIM
WRITE
SV 0010
Timer/Counter SV Change 2: Fine Adjustment of a Constant

This operation is used to increment or decrement a constant specified for the
set value of a timer/counter in the user program.
Key Sequence
↓
Timer/counter SV display CHG CHG CLR CLR WRITE
Operation Example The following example describes how to adjust the constant specified for the
TIM 0001 set value.
1,2,3... 1. From the initial display, access the timer/counter instruction for which the
set values will be changed.
000000 CT00
CLR
¡
CF 000201 CT00 FIND

TIM 1 SRCH TIM 0001
000201 TIM
↓ SV #0020
2. Start the Timer/Counter SV Change 2 operation.
000201SV U/D?
CHG CHG
#0020
3. Incremented or decremented the constant using the Up and Down Keys.
000201SV U/D?
↑ ↓
or #0021
Incremented for the

↓ Down Key.
Decremented for the
↑ Up Key.
4. Exit the operation. The new set value will be displayed.
75
000201 TIM
CLR CLR
SV #0021
000202 CT00
WRITE
LD 000100
76
SECTION 5
Checking and Adjusting Programs
This section describes how to monitor programs in different display modes, for the purpose of checking and making
adjustments. It also includes information on how to change values from various displays for adjusting programs.
5-1 Reading Program Execution Status. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78

5-2 Simple I/O Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
5-2-1 Monitoring Specified Addresses in I/O Memory . . . . . . . . . . . . . . . 79
5-2-2 Monitoring Operands at Specified Program Addresses . . . . . . . . . . 84
5-3 I/O Multipoint Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
5-4 Monitor Display Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
5-4-1 Word (Multipoint) Monitor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
5-4-2 Signed Decimal Monitor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
5-4-3 Unsigned Decimal Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
5-4-4 ASCII Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
5-5 Changing Word (16-bit) Present Values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
5-5-1 Basic Procedure for Changing PVs . . . . . . . . . . . . . . . . . . . . . . . . . 92
5-5-2 Changing PVs from Hexadecimal or BCD Display . . . . . . . . . . . . . 93
5-5-3 Changing PVs from Signed Decimal Monitor . . . . . . . . . . . . . . . . . 94
5-5-4 Changing PVs from Unsigned Decimal Monitor . . . . . . . . . . . . . . . 96
5-5-5 Changing PVs from the ASCII Monitor. . . . . . . . . . . . . . . . . . . . . . 97
5-5-6 Changing PVs from the Word (Multiple-bit) Monitor . . . . . . . . . . . 98
5-6 Forcing Bits ON/OFF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
5-6-1 Continuous Force Set/Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
5-6-2 Temporary Force Set/Reset. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
5-6-3 Clear Force Set/Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
5-7 Differential Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
5-8 Online Editing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
5-8-1 Instruction Change . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
5-8-2 Instruction Add . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
5-8-3 Instruction Insert. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
5-8-4 Instruction Delete . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
5-8-5 Bit Address Change . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
5-8-6 N.O./N.C. Change. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
5-8-7 Instruction Variation Change . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
5-8-8 Timer/Counter SV Change . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
77
Reading Program Execution Status Section 5-1
5-1 Reading Program Execution Status

I/O Bit Status Monitor
RUN MONITOR PROGRAM
OK OK No
This operation is used to read the program execution status one address at a
time. By monitoring the ON/OFF status of bits or timer/counter Completion
Flags, the execution status of the program can be read from the Programming
Console display. The key sequence is the same as that for reading the pro-
gram.
Key Sequence
Initial display Specify program address ↓
Operation Example In the following example, the ON/OFF status of the bits in the program are
read.
Program example
000000 000001 000100
000123
TIM000
#0010
T0000 000100
END(001)
1,2,3... 1. From the initial display, specify the program address to read. In this exam-
ple, program address 123 is specified.
000000 CT00
CLR
¡
000123
1 2 3
2. Read the program. The ON/OFF status of bits will be displayed as “0” or
“1.”
000123 CT00 0
↓
LD 000000
The ON/OFF status of bits will be
displayed as follows:
0: OFF, 1: ON
78
Simple I/O Monitor Section 5-2
000124 CT00 1
↓
AND N 000001
When normally closed bits are ON,
the I/O status is still displayed as " 1."
000125 CT00 0
↓ OUT 000100
000126 CT00 0
↓ TIM 0000
000126 TIM
↓ SV #0010
000127 CT00 0
↓ LD T0000
3. Press the CLR Key to end the operation.
Note When the MON Key is pressed during I/O bit status monitoring, the
Programming Console will be switched to the Simple I/O Monitor op-
eration. To switch back to the I/O Bit Status Monitor operation, press
the CLR Key once more.
5-2 Simple I/O Monitor

RUN MONITOR PROGRAM
OK OK OK
This operation is used to monitor present values in I/O memory one bit or one
word at a time.
• There are two methods for I/O monitoring, as follows:
a) Monitoring specified addresses in I/O memory.
b) Specifying program addresses and monitoring the operands of the
corresponding instructions.
• Simple I/O Monitor is available in RUN, MONITOR and PROGRAM
modes.
• When monitoring bit status, the ON/OFF status of the bit can be changed.
Refer to 5-6 Forcing Bits ON/OFF for details.
• When monitoring word data (16-bit data), the contents of the word can be
changed. Refer to 5-5 Changing Word (16-bit) Present Values for details.
5-2-1 Monitoring Specified Addresses in I/O Memory

Monitoring ON/OFF Status of Specified Bits (Single-bit Data)
Key Sequence
CONT
SHIFT
#
Specify area Bit address MON ↓ ↑
(To monitor previous/next
bit address)
Specify program address ↓ CLR
79
Operation Example In the following example, auxiliary bit (AR) A40109 is monitored.
1,2,3... 1. From the initial display, input the bit address to be monitored. In this exam-
ple, input A40109.
000000 CT00
CLR
¡
CONT AR
SHIFT
#
SHIFT
HR
4 0 1 0 9
000000
BIT A40109
2. Start monitoring.
MON A40109 ^ ON
PV (Bit display)
• Press the Up and Down Keys to monitor either the previous or the next
bit.
• Bit ON/OFF status can be changed from this display.
3. Press the CLR Key to exit Simple I/O Monitor.
Designating Bit Address for Monitoring

CONT
SHIFT Number
#
000000
BIT 000015
Work bits Bit 15 of W000
CONT *EM
(WR) SHIFT
# WR/LR Number
000000
BIT W00015
Holding Bit 15 of H000
CONT AR
bits (HR) SHIFT
# HR
Number
000000
BIT H00015
Auxiliary Bit 15 of A000
CONT AR
bits (AR) SHIFT
#
SHIFT Number
HR
000000
BIT A00015
80

Clock Always ON Flag
CF
pulse/Con- SHIFT
SRCH
dition Flag 000000
BIT ON
Display Bit
When clock pulses or Condition Flags
ON Always ON Flag
are designated, the bits listed at the
right can be designated, by using the OFF Always OFF Flag
Up and Down Keys. AER Access Error Flag
1s 1-s clock pulse
ER Error Flag
CY Carry Flag
> Greater Than Flag
= Equals Flag
< Less Than Flag
N Negative Flag
OF Overflow Flag
UF Underflow Flag
<> Not Equal Flag
Task Flag TK0000

TK
SHIFT Number
CNT
000000
BIT TK0000
Monitoring Timer/Counter Completion Flags and PVs

Set value input range Simple I/O Monitor present value display
(initial status)
#0000 to #9999 0000 to 9999
Example: When the present value is 10 s, the values are as follows:

Set value input range Simple I/O Monitor present value display
(initial status)
#0100 0100
Key Sequence
TIM Timer number MON
TK
Counter number MON
CNT
81
Operation Example In the following example, TIM 0010 is monitored.
1,2,3... 1. From the initial display, input the number of the timer instruction to be mon-
itored. In this example, input TIM 0010.
000000 CT00
CLR
¡
000000
TIM 1 0
TIM 0010
MON T0010 0236
Timer PV
• The Completion Flag and PV are monitored at the same time.

• When the timer/counter PV becomes “0,” the Completion Flag will turn
ON and a symbol will be displayed to the right of the PV.
T0010 0236
Completion Flag Timer PV

Designating Timer/Counter Numbers for Monitoring
Timer PVs TIM0100
TIM Number
000000
TIM 0100
Counter PVs C0010
TK
Number
CNT 000000
CNT 0010
Monitoring the PVs of Designated Words (16-bit Data)

Key Sequence
CH
SHIFT
*DM
Specify area Word address MON
Operation Example In the following example, D00100 in data memory is monitored.
1,2,3... 1. From the initial display, input the DM address to be monitored. In this ex-
ample, input D00100.
000000 CT00
CLR
¡
EM 000000
1 0 0
DM WORD D00100
82
MON D00100 FFFF
PV (Hexadecimal display)
• Press the Up and Down Keys to monitor either the previous or the next
word.
• Word values can be changed from this display.
Designating Word Addresses (16-bit) for Monitoring

CIO words CIO0010
CH
SHIFT
*DM Number
000000
WORD 0010
Work words W010
(WR) SHIFT CH
*DM
000000
*EM
WORD W010
Number
WR/LR
Holding words H010

CH
(HR) SHIFT
*DM
000000
AR WORD H010
HR
Number
Auxiliary words A010

CH
(AR) SHIFT
*DM
000000
SHIFT
AR
Number WORD A010
HR
Data memory D00010

EM
words (DM) Number
DM
000000
WORD D00010
Extended DM E0_00010
*EM_
(EM): With bank EM_/EXT Number
000000
(Bank number, WORD E0_00010
word address)
Extended DM E00010
EM
(EM): Current SHIFT Number
DM
bank 000000
(Word address) WORD E00010
Data Registers DR1
DR
(DR) SHIFT Number
IR
000000
Regi DR01
Index Registers IR1
DR
(IR) Number
IR 000000
Regi IR01
83
5-2-2 Monitoring Operands at Specified Program Addresses

Key Sequence
Initial display Specify program address ↓ MON
One Operand
Operation Example In the following example, the PV for the TIM instruction at program address
000200 is monitored.
1,2,3... 1. From the initial display, input the program address of the instruction whose
operand is to be monitored. In this example, input program address
000200.
000000 CT00
CLR
¡
000200 CT00 0
2 0 0 ↓ TIM 0000
MON T0000 1234
Present value
000200
CLR
TIM 0000
Two or More Operands

Operation Example In the following example, operands for the MOV(021) instruction at program
address 000202 is monitored
1,2,3... 1. From the initial display, input the program address of the instruction whose
operands to be monitored. In this example, input program address 000202.
000000 CT00
CLR
¡
000202 CT00
2 0 2 ↓ MOV(021)
2. Select the operands to be monitored. The following example shows the
display for the first and second operands.
000202 MOV First

↓ ↑ operand
SV A 0010
000202 MOV Second

SV B 0011 operand
84
I/O Multipoint Monitor Section 5-3
MON 0011 1234
Present value
000202
CLR
WORD 0011
5-3 I/O Multipoint Monitor
RUN MONITOR PROGRAM
OK OK OK
This operation is used to monitor up to four bits or words simultaneously.

• Four bits and/or words can be monitored at the same time, but only 2 of
these can be displayed simultaneously.
Key Sequence
Simple I/O Monitor Simple I/O Monitor
Operation Example In the following example, T0001, CIO 000001, D00000, and CIO 1225 are
monitored.
1,2,3... 1. Specify the bits and words for monitoring, in succession as shown in the
following steps. The status/present values of the specified bits and words
will appear at the top of the display. Methods for specifying bits or words
are the same as for Simple I/O Monitor.
000000 CT00
CLR
¡
a) Specify T0001 and the present value will appear at the top of the dis-
play.
TIM 1 MON T0001 0100
The present value

for T 0001.
b) Specify CIO bit 000001 and the status will appear at the top of the dis-
play.
SHIFT
CONT
1 MON 000001 ^ OFF
#
T0001 0100
The present value
for 000001.
The present value
for T 0001.
85
c) Specify D000000 and the present value will appear at the top of the
display.
EM
MON D00000 1234
DM
000001 ^ OFF
The present value
for D 00000.
The present value
for 000001.
d) Specify CIO 1225 and the present value will appear at the top of the
display.
2 2 5 MON 1225 0000

1
D00000 1234
The present
value for 1225.
The present value
for D 00000.
• A total of up to 4 bits and words can be specified, but only a maximum of

2 of these will be displayed at any one time. If more than 4 bits/words are
specified, old ones will be cleared from the monitor operation.
2. Press the MON Key to display bits and words that were not visible.
MON
T0001 0100
1225 0000
3. Press the CLR Key and bit/word being monitored on the top line will be
cleared from monitor operation.
1225 0000
CLR
D00000 1234
Saving I/O Multipoint Monitor Results

This operation is used to save the current bits/words specified for the I/O Mul-
tipoint Monitor operation while performing other operations.
Key Sequence
Saving I/O Multipoint Monitor results: I/O Multipoint Monitor display SHIFT CLR
Returning to I/O Multipoint Monitor: SHIFT MON
Operation Example
1,2,3... 1. From the I/O Multipoint Monitor display, press the SHIFT then CLR Keys to
return to the initial display.
1225 0000
D00000 1234
SHIFT
000000
CLR
WORD 1225
86
2. From the initial display, perform any operation other than I/O Multipoint
Monitor.
000000 CT00
CLR
3. When you have finished performing other operations, return to the saved
monitoring status by accessing the I/O Multipoint Monitor display.
SHIFT MON
1225 0000
D00000 1234
Clearing all Monitor Displays

This operation is used to clear from the display all bits/words being monitored
in I/O Multipoint Monitor. The specification of the bits/words being monitoring
will be saved and the Multipoint I/O Monitor operation can be returned to
using the procedure described in the preceding section.
Key Sequence
SHIFT CLR
Operation Example From the I/O Multipoint Monitor display, press SHIFT then CLR Keys.
1225 0000
D00000 1234
SHIFT
000000
CLR
WORD 1225
87
Monitor Display Format Section 5-4
5-4 Monitor Display Format

The display format for words (16-bit data) in Simple I/O Monitor or I/O Multi-
point Monitor can be changed to display formats other then binary (i.e., 4-digit
and 2-digit hexadecimal), such as signed decimal, unsigned decimal, and
ASCII. The word (16-bit data) display format can be changed using the follow-
ing key combinations.
Simple I/O Monitor I/O Multipoint Monitor
(Simple I/O Monitor displays are shown.)

Hexadecimal or 4-digit BCD 16-digit BCD
D00200 B141 D00200 MON

1011000101000001
SHIFT MON
,–IR
Data display change TR
CLR
Signed decimal Signed double-word decimal

D00200 -20159 D00201 D00200
+45377
,IR+
,IR
,–IR ,–IR
CLR NOT
TR TR C
CLR
Unsigned decimal Unsigned double-word decimal
D00200 &45377 D00201 D00200

&45377
,IR+
,–IR ,IR
CLR
TR
CLR
ASCII
D00200 "1A"
,–IR
CLR
TR
88
5-4-1 Word (Multipoint) Monitor

RUN MONITOR PROGRAM
OK OK OK
This operation monitors I/O memory bit status in one word (16 bits) at a time.
• The following words can be monitored:
• I/O bits
• Holding bits
• Data memory
• Data registers
• Work bits
• Auxiliary bits
• Extended data memory
• Index registers
• The status of the 16 bits will be shown on the bottom line of the display
using 1, 0, S, and R as follows:
1: ON S: Force Set
0: OFF R: Force Reset
Key Sequence
Simple I/O Monitor display

SHIFT MON
I/O Multipoint Monitor display
Operation Example In the following example, CIO 2670 is monitored using a word (multipoint) dis-
play.
1,2,3... 1. Access the Simple I/O Monitor display and display the word for monitoring.
CIO 2670
2670 F000
2. Switch to word monitoring.
SHIFT MON
2670 MON
1111000000000000
• Use the Up or Down Key to display the next or previous word.
• From this display, word values can be changed one bit at a time. Refer
to page 5-5 Changing Word (16-bit) Present Values.
• The Force Set/Reset status of bits will also be displayed. (S: Force Set,
R: Force Reset)
2670 MON
11S100R000000000
Force Set
Force Reset
89
3. Press the CLR Key to stop word monitoring and return to the Simple I/O
Monitor display.
2670 F000
CLR
5-4-2 Signed Decimal Monitor

RUN MONITOR PROGRAM
OK OK OK
This operation converts the hexadecimal contents of words from 2’s comple-
ment to a signed decimal data display.
This operation can be performed during Simple I/O Monitor or I/O Multipoint
Monitor.
Key Sequence

,–IR
TR
Operation Example In the following example, CIO 2670 is monitored using a signed decimal data
display.
1,2,3... 1. Access the Simple I/O Monitor or I/O Multipoint Monitor display and display
the word for monitoring.
CIO 2670
2670 FFF0
During I/O Multipoint monitoring, the word at the top of the screen will be
changed.
2. Convert the display format to signed decimal.
,–IR 2670 -16

TR
3. Convert the display to a double-word display.

When CIO 2671 is 0000 Hex:
,IR+ 2671 2670

,IR +65520
From this display, word data can be converted to signed decimal. (Refer to
page 94.)
4. Press the CLR Key to exit the double-word display and return to Signed
Decimal Monitor.
2670 -16
CLR
90
5. Press the CLR Key again to return the display from Signed Decimal Mon-
itor to either Simple I/O Monitor or I/O Multipoint Monitor.
2670 FFF0
CLR
5-4-3 Unsigned Decimal Monitor

RUN MONITOR PROGRAM
OK OK OK
This operation converts the hexadecimal contents of word data into unsigned
decimal data for display.
Monitor.
Key Sequence

,–IR ,–IR
TR TR
Operation Example In the following example, CIO 2670 is monitored using an unsigned decimal
display.
the word for monitoring.
CIO 2670
2670 FFF0
During I/O Multipoint Monitor, the word at the top of the screen will be
changed.
2. Convert the display format to unsigned decimal.
,–IR ,–IR 2670 &65520

TR TR
3. Convert the display to a double-word display.

When CIO 2671 is 0000 Hex:
,IR+ 2671 2670

,IR &65520
From this display, word data can be converted to signed decimal. (Refer to
page 96.)
4. Press the CLR Key to exit double-word display and return to Unsigned
Decimal Monitor.
2670 &65520
CLR
91
Changing Word (16-bit) Present Values Section 5-5
5. Press the CLR Key again to return the display from Unsigned Decimal
Monitor to either Simple I/O Monitor or I/O Multipoint Monitor.
2670 FFF0
CLR
5-4-4 ASCII Monitor

RUN MONITOR PROGRAM
OK OK OK
This operation reads the hexadecimal contents of words as ASCII data, and
displays them as ASCII text.
• This operation can be performed during Simple I/O Monitor or I/O Multi-
point Monitor.
• For details on ASCII characters which can be displayed, refer to Appendix
B.
Key Sequence

,–IR ,–IR ,–IR
TR TR TR
Operation Example In the following example, D00000 is monitored using an ASCII display.
the word for which the display will be changed.
D 00000
D00000 4142
2. Convert the display format to ASCII display.
,–IR ,–IR ,–IR D00000 "AB"

TR TR TR
3. Press the CLR Key to exit ASCII display and return to either Simple I/O
Monitor or I/O Multipoint Monitor.
D00000 4142
CLR
5-5 Changing Word (16-bit) Present Values

5-5-1 Basic Procedure for Changing PVs
RUN MONITOR PROGRAM
No OK OK
The operations used to change word data are illustrated below.
92
!Caution Always confirm safety before changing data even when working in PRO-
GRAM mode. The CPU Unit will refresh I/O even in PROGRAM mode. If the
status of a bit allocated to an Output Unit, Special I/O Unit, or CPU Bus Unit is
changed, the load connected to the Unit may operate unexpectedly.
Simple I/O Monitor display I/O Multipoint Monitor display
Hexadecimal or 4-digit BCD display
D00200 B141 CHG

Enter hexadecimal or 4-digit WRITE
BCD
,–IR
TR
Signed decimal display
D00200 -20159 CHG Enter signed decimal WRITE
,–IR
CLR
TR
Unsigned decimal display
D00200 &45377 CHG Enter unsigned decimal WRITE
,–IR
CLR
TR
ASCII display
D00200 "1A" CHG Enter alphanumeric text WRITE
,–IR
CLR
TR
5-5-2 Changing PVs from Hexadecimal or BCD Display

RUN MONITOR PROGRAM
No OK OK
This operation changes word (16-bit) present values using hexadecimal or 4-

digit BCD.
93
Monitor. From I/O Multipoint Monitor, the top value on the display will be
changed.
Key Sequence

CHG Enter hexadecimal or WRITE
4-digit BCD
Operation Example The following example changes the present value of D00200.
1,2,3... 1. Access the Simple I/O Monitor or I/O Multipoint Monitor and bring up the
word for changing.
D 00200
D00200 001A
2. Specify changing the value from the hexadecimal display.
D00200 001A
CHG
PV ????
3. Input the new value and return to Simple I/O Monitor or Multipoint I/O Mon-
itor.
SHIFT
B D00200 001B
1 1 WRITE
5-5-3 Changing PVs from Signed Decimal Monitor

RUN MONITOR PROGRAM
No OK OK
This operation changes present values for word data using signed decimal
(single-word: –32768 to 32767, double-word: –214783648 to 214783647).
The 2’s complement expression is automatically converted to hexadecimal.
changed.
Key Sequence
Signed Decimal Monitor display CHG Enter signed decimal WRITE
94
Signed Decimal Displays

Operation Example The following example changes the present value of D00200.
1,2,3... 1. Access the Simple I/O Monitor or I/O Multipoint Monitor as signed decimal
display, and bring up the word for changing.
D 00200
D00200 -16
2. Specify changing the value from the signed decimal display.
D00200 -16
CHG
PV -?????
3. Input the new value and return to Signed Decimal Monitor.
D00200 -16
SET PV +?????
3 2 7 6 7 WRITE
D00200 +32767
• When inputting positive numbers, press the SET Key; when inputting
negative numbers, press the RESET Key.
• When an error is made inputting, press the CLR Key to return to the
previous display, then enter the value correctly.
Double-word Displays
Operation Example The following example changes the present values of D00201 and D00200.
1,2,3... 1. Access the Simple I/O Monitor or I/O Multipoint Monitor as signed decimal
display, and bring up the words for changing.
D 00201, D00200
D00201 D00200
+65520
2. Specify changing the values from the double-word signed decimal display.
D00201 PV?
CHG
+65520
3. Input the new values and return to Signed Decimal Monitor.
D00201 PV?
RESET -65520
3 2 7 6 8 WRITE
D00201 D00200
-32768
95
• When inputting positive numbers, press the SET Key; when inputting
negative numbers, press the RESET Key.
• When an error is made inputting, press the CLR Key to return to the
previous display, then enter the value correctly.
5-5-4 Changing PVs from Unsigned Decimal Monitor

RUN MONITOR PROGRAM
No OK OK
This operation changes present values for word data using unsigned decimal
(single-word data: 0 to 65535, double-word: 0 to 4294967295). Conversions
to hexadecimal are performed automatically.
changed.
Key Sequence
Enter values in un
Unsigned Decimal Monitor display CHG
signed decimal WRITE
Unsigned Decimal Displays

Operation Example The following example changes the present value of CIO 0100.
1,2,3... 1. Access the Simple I/O Monitor or I/O Multipoint Monitor as unsigned deci-
mal display, and bring up the word for changing.
CIO 0100
0100 &65520
2. Specify changing the value from the unsigned decimal display.
0100 &65520
CHG
PV? &?????
3. Input the new value and return to Unsigned Decimal Monitor.
6 5 5 3 5 WRITE
0100 &65535
When an error is made inputting, press the CLR Key to return to the previ-
ous display, then enter the value correctly.
96
Double-word Display
1,2,3... 1. Access the Simple I/O Monitor or I/O Multipoint Monitor as unsigned deci-
mal display, and bring up the words for changing.
CIO 0101, CIO 0100
0101 0100
&65520
2. Specify changing the values from the double-word unsigned decimal dis-
play.
0101 PV?
CHG
&65520
3. Input the new values and return to Unsigned Decimal Monitor.
6 5 5 3 5 WRITE
0101 0100
&65535
When an error is made inputting, press the CLR Key to return to the previ-
ous display, then enter the value correctly.
5-5-5 Changing PVs from the ASCII Monitor
RUN MONITOR PROGRAM
No OK OK
This operation changes present values for word data using ASCII.
• This operation can be performed during Simple I/O Monitor or I/O Multi-
point Monitor. From I/O Multipoint Monitor, the top value on the display will
be changed.
• For details on ASCII characters which can be displayed, refer to Appendix
B.
Key Sequence
ASCII Monitor display CHG Enter values as numerals. WRITE
Operation Example The following example changes the present value for D00000.
1,2,3... 1. Access the Simple I/O Monitor or I/O Multipoint Monitor as an ASCII dis-
play, and bring up the word for changing.
D 00000
D00000 "AB"
2. Specify changing the text from the ASCII display.
D00000 "AB"!
CHG
PV "??"
97
When “ ” is displayed, the text on the lower-left of the keys will be input
when keys are pressed.
3. Input the new value and return to Simple I/O Monitor or I/O Multipoint Mon-
itor.
SFT NOT
D00000 "BC"
WRITE
B C
5-5-6 Changing PVs from the Word (Multiple-bit) Monitor

RUN MONITOR PROGRAM
No OK OK
This operation converts word (16-bit) present values to multiple-bit (16-bit

binary) format. This operation can be used during Word (Multiple-bit) Monitor.
Key Sequence
Word (Multiple-bit) Monitor display
0 1
CHG WRITE
SHIFT SHIFT NOT

SET RESET
Operation Example The following example changes the present value of CIO 0001.
1,2,3... 1. Access the Word (Multiple-bit Monitor) and bring up the word to be
changed.
CIO 0001
0001 MON
11110000S00000R0
2. Press the CHG Key to specify changing the present value.
0001 CHG?
CHG
~1110000S00000R0
3. Press the Up and Down Keys to move the cursor to the bit to be changed.
0001 CHG?
↓ ↑
1111~000S00000R0
4. Specify the new value.
0001 CHG?
1
1111~000S00000R0
The cursor position after inputting a new value varies depending on the last
key pressed for moving the cursor.
Press the Up and Down Keys to confirm the new value.
98
Forcing Bits ON/OFF Section 5-6
Press the Down Key Press the Up Key
0001 CHG? 0001 CHG?

11111~00S00000R0 111~1000S00000R0
The procedure for inputting the new value is as follows:
0 : OFF
1 : ON
SHIFT
SET : Force Set (S) (Not possible in data memory)
SHIFT
RESET
: Force Reset (R) (Not possible in data memory)
NOT : Clear Force Set/Reset
5. Input the new values and return to the Word Monitor.
0001 MON
WRITE
11111000S00000R0
5-6 Forcing Bits ON/OFF

RUN MONITOR PROGRAM
No OK OK
This operation is used to force bits ON/OFF regardless of any external inputs
or results of user program execution. This operation can be performed during
Simple I/O Monitor or I/O Multipoint Monitor.
!Caution Always confirm safety before setting or resetting bits even when working in
PROGRAM mode. The CPU Unit will refresh I/O even in PROGRAM mode. If
the status of a bit allocated to an Output Unit, Special I/O Unit, or CPU Bus
Unit is changed, the load connected to the Unit may operate unexpectedly.
5-6-1 Continuous Force Set/Reset

Key Sequence
Force Set: SHIFT
SET
Force Reset: SHIFT
RESET
Clear: NOT
Operation Example The following example uses Force Set/Reset to reset bit 00 of CIO 0001.
1,2,3... 1. Access the Simple I/O Monitor or the I/O Multipoint Monitor and bring up
the bit to be Force Set/Reset. The following example shows the I/O Multi-
point Monitor.
Bit 00 of CIO 0001
000100 ^ OFF
000001 ^ ON
99
Forcing Bits ON/OFF Section 5-6
From the I/O Multipoint Monitor, the bit at the top of the display will be
changed.
2. When a bit has been Force Set, an “S” will appear and when it has been
Force Reset, an “R” will appear on the display. The forced ON/OFF status
of the bit will not be affected by external input changes or the result of ex-
ecuting a command.
SHIFT
000100 S ON
SET 000001 ^ ON
Key sequence:
SHIFT
SET : Continuous Force Set.
SHIFT
RESET : Continuous Force Reset.
NOT : Continuous Force Set/Reset clear.
Continuous Force Set/Reset can be cleared by pressing the NOT Key to

perform the Clear Force Set/Reset operation. Force Set/Reset is cleared
when the following operations are performed:
a) When the Clear Force Set/Reset operation is executed.
b) When the operating mode of the PC is changed. If the Forced Status
Hold Bit is ON, however, Force Set/Reset bits will not be cleared when
the PC mode is changed from PROGRAM to MONITOR.
c) When operation stops as the result of a fatal error.
d) When operation stops as a result of power interruption.
5-6-2 Temporary Force Set/Reset

This operation force-sets/resets a bit only while the key is held down.
Key Sequence
Simple I/O Monitor display Force Set:

SET
I/O Multipoint Monitor display Force Reset:

RESET
Operation Example The following example uses Force Set/Reset to reset bit 00 of CIO 0001.
1,2,3... 1. Access the Simple I/O Monitor or the I/O Multipoint Monitor and bring up
the bit to be Force Set/Reset. The following example shows the I/O Multi-
point Monitor.
Bit 00 of CIO 0001
000100 ^ OFF
000001 ^ ON
From the I/O Multipoint Monitor, the bit at the top of the display will be
changed.
2. The bit will be force-set/reset only while the key is being pressed. While the
key is being pressed, a black square will be displayed.
000100 ~ OFF
SET 000001 ^ ON
100
Differential Monitor Section 5-7
Key sequence
SET : Force Set (Only while the key is pressed.)
RESET : Force Reset (Only while the key is pressed.)
5-6-3 Clear Force Set/Reset

This operation clears all bits that are being force-set/reset.
Key Sequence
NOT
SET RESET
Operation Example Use the following key strokes to clear all force-set/reset bits.
000000REL FORCED
SET RESET ?
000000REL FORCED
NOT
END
Note Press the CLR Key to cancel the operation.
5-7 Differential Monitor

RUN MONITOR PROGRAM
OK OK No
This operation monitors an OFF to ON (upward differentiation) or ON to OFF

(downward differentiation) change in the status of a specific bit. When the
change is detected, the status will be displayed and the buzzer will sound.
This operation can be used during Simple I/O Monitor or I/O Multipoint Moni-
tor.
Key Sequence
Differentiation up SHIFT ↑
Simple I/O Monitor display detected:
Differentiation down SHIFT ↓

detected:
Operation Example The following example detects the differentiate up/differentiate down status of
bit 10 of CIO 0100.
1,2,3... 1. Access the Simple I/O Monitor or I/O Multipoint Monitor display, and bring
up the bit to be monitored.
Bit 10 of CIO 0100
010010 ^ OFF
From the I/O Multipoint Monitor, the bit at the top of the display will be mon-
itored.
2. Set detection of the differentiate up status. In this example, an OFF to ON
change is detected in the status of CIO 010010.
101
Online Editing Section 5-8
010010 U@OFF
SHIFT ↑
3. When the specified bit turns ON, the display will change and the buzzer will
sound.
010010 ^ ON
4. Set detection of differentiate down status. In this example, an ON to OFF

change is detected in the status of bit CIO 010010.
010010 D@ ON
SHIFT ↓
5. When the specified bit turns OFF, the display will change and the buzzer
will sound.
010010 ^ OFF
To exit the Differential Monitor operation, press the CLR Key.
5-8 Online Editing

5-8-1 Instruction Change
RUN MONITOR PROGRAM
No OK OK
This operation is used when the CPU Unit is in MONITOR mode to overwrite
instructions in user programs.
Key Sequence
Program address display Input instruction WRITE WRITE
Operation Example In the following instruction block, the instruction at address 00200 will be
changed to LD NOT 000002.
: : :
000201 AND 000200
: : :
1,2,3... 1. From the initial display, access the program address containing the instruc-
tion to be changed.
000000 CT00
CLR
¡
000200 CT00 0
2 0 0 ↓ LD 000001
2. Input the new instruction and press the WRITE Key.
102
AA ONLINE EDIT?
NOT 2 WRITE
LD LD N 000002
3. Press the WRITE Key once more.
000201 CT00 0
WRITE
AND 000200
After pressing the WRITE Key the second time, the altered program will be
executed from the next scan.
000200 CT00 1
↑
LD N 000002
5-8-2 Instruction Add

RUN MONITOR PROGRAM
No OK See note.
This operation is used when the CPU Unit is in MONITOR mode to add an
instruction to the end of the user program.
Note Refer to 4-1 Inputting Instructions for details on adding instructions in PRO-
GRAM mode.
Key Sequence
Program address display Input instruction WRITE WRITE
Operation Example In the following instruction block, LD 000002 and OUT 000100 are added
before the END(001) instruction.
: : :
LD 000002 and OUT 000100 are
123456 END added.
1,2,3... 1. From the initial display, access the last program address.
000000 CT00
CLR
1 2 3 4 5 6 ↓
123456 CT00
END(001)
2. Specify the instruction to be added and press the WRITE Key.
AA ONLINE EDIT?
2 WRITE
LD LD 000002
123457 CT00
WRITE
END(001)
103
4. Continue to specify the next instruction to be added and press the WRITE
Key after each one.
AC ONLINE EDIT?
1 0 0 WRITE
OUT OUT 000100
123458 CT00
WRITE
END(001)
6. Use the Up Key to check that the instruction has been added.
123457 CT00 0
↑
OUT 000100
123456 CT00 0
↑
LD 000002
5-8-3 Instruction Insert

RUN MONITOR PROGRAM
No OK See note.
This operation is used when the CPU Unit is in MONITOR mode to insert
instructions into the middle of a user program.
Note Refer to 4-3-2 Instruction Insert for details on inserting instructions in PRO-
GRAM mode.
Key Sequence
Program address display Input instruction INS ↓ WRITE
Operation Example In the following instruction block, AND 000100 will be inserted in front of
address 00201.
: : :
000200 LD 000001
AND 000100 will be inserted.
000201 AND 000200
: : :
1,2,3... 1. From the initial display, access the program where the address to be insert-
ed.
000000 CT00
CLR
¡
000201 CT00 0
2 0 1 ↓ AND 000200
2. Specify the instruction to be inserted, and press the INS Key.
000201 INS?
AND 1 0 0 INS
AND 000100
104
3. Press the Down Key. A confirmation message will be displayed, asking

whether or not to execute the instruction insert using Online Edit.
ONLINE EDIT/INS?
↓ AND 000100
4. If the instruction requires more than one operand, specify the set values
(operands), and press the WRITE Key after each.
5. To execute, press the WRITE Key.
000202 CT00 0
WRITE
AND 000200
6. Press the Up Key to confirm that the instruction has been inserted.
000201 CT00 0
↑
AND 000100
5-8-4 Instruction Delete

RUN MONITOR PROGRAM
No OK See note.
This operation is used when the CPU Unit is in MONITOR mode to delete
instructions from the user program.
Note Refer to 4-3-3 Instruction Delete for details on deleting instructions in PRO-
GRAM mode.
Key Sequence
Program address display DEL ↑
Operation Example In the following instruction block, AND 000200 will be deleted from address
00201.
: : :
000200 LD 000001
000201 AND 000200 Delete
000202 OUT 000100
: : :
1,2,3... 1. From the initial display, access the program address of the instruction to be
deleted.
000000 CT00
CLR
¡
000201 CT00 0
2 0 1 ↓ AND 000200
2. Delete the address.
105
ONLINE EDIT/DEL?
DEL
AND 000200
3. To execute, press the Up Key. The next program address will be shifted for-
wards.
000201 DEL END0

↑
OUT 000100
• After pressing the Up Key the second time, the altered program will be
• When a multiple-operand instruction is deleted, the set values (oper-
ands) will also be deleted.
5-8-5 Bit Address Change

RUN MONITOR PROGRAM
No OK See note.
This operation is used when the CPU Unit is in MONITOR mode to change bit
addresses used as operands in the user program.
Note Refer to 4-3-4 Bit Address Change for details on changing bit addresses in
PROGRAM mode.
Key Sequence
Program address display Input bit address WRITE WRITE
Operation Example In the following instruction block, the bit address in the instruction at program
address 00200 (LD 000001) will be changed to CIO 000002.
: : :
000200 LD 000001 The bit address will be changed to
CIO 000002.
000201 AND 000200
: : :
1,2,3... 1. From the initial display, access the program address containing the bit ad-
dress to be changed.
000000 CT00
CLR
¡
000200 CT00 0
2 0 0 ↓ LD 000001
2. Specify the new bit address, and press the WRITE Key.
ONLINE EDIT?
2 WRITE
LD 000002
000201 CT00 0
WRITE
AND 000200
106
4. Press the Up Key to check that the address of the bit operand has been
changed.
000200 CT00 0
↑
LD 000002
5-8-6 N.O./N.C. Change

RUN MONITOR PROGRAM
No OK See note.
This operation is used when the CPU Unit is in MONITOR mode to change
N.O. and N.C. conditions in the user program.
Note Refer to 4-3-5 N.O./N.C. Change for details on changing bit addresses in
PROGRAM mode.
Key Sequence
Program address display NOT WRITE WRITE
Operation Example In the following instruction block, the instruction at program address 000200 is
changed from LD 000001 to LD NOT 000001.
: : :
000201 AND 000200
: : :
tion to be changed.
000000 CT00
CLR
¡
000200 CT00 0
2 0 0 ↓ LD 000001
2. Press the NOT Key and then the WRITE Key.
ONLINE EDIT?
NOT WRITE
LD N 000001
000201 CT00 0
WRITE
AND 000200
4. Use the Up Key to check that LD has been changed to LD NOT.
000200 CT00 1
↑
LD N 000001
107
5-8-7 Instruction Variation Change

RUN MONITOR PROGRAM
No OK See note.
This operation is used when the CPU Unit is in MONITOR mode to change
the variation of an instruction in the user program.
Note Refer to 4-3-6 Instruction Variation Change for details on changing bit
addresses in PROGRAM mode.
Key Sequence
Differentiate up
Program address display WRITE WRITE
SHIFT
SET
Differentiate down
SHIFT
RESET
Immediate refresh
TEXT
!
Operation Example In the following instruction block, the instruction at address 000200 (LD
000001) will be changed to an upwardly differentiated LD instruction.
: : :
000200 LD 000001 Changed to upwardly differentiated
000201 AND 000200 @LD 000001.
: : :
tion to be changed.
000000 CT00
CLR
¡
000200 CT00 0
2 0 0 ↓ LD 000001
2. Specify the variation and press the WRITE Key.
SHIFT
ONLINE EDIT?
WRITE
SET @LD 000001
000201 CT00 0
WRITE
AND 000200
4. Use the Up Key to check the variation has changed.
000200 CT00 0
↑
@LD 000001
108
5-8-8 Timer/Counter SV Change

RUN MONITOR PROGRAM
No OK See note.
Note Refer to 4-3-7 Timer/Counter SV Changes for details on changing timer/

counter set values in PROGRAM mode.
Timer/Counter SV Change 1: Constant or Word

This operation is used to change the set value of a timer/counter in the user
program.
Key Sequence
Designated constants
Timer/counter SV display CHG WRITE WRITE WRITE
Designated words
Operation Example The following example describes how to change the set value of TIM 0001.
1,2,3... 1. From the initial display, access the timer/counter for which the set value will
be changed.
000000 CT00
CLR
¡
CF 000201 CT00 FIND

TIM 1 SRCH TIM 0001
000201 TIM
↓ SV #0100
2. Specify changing the set value from the above display.
000201SV ?
CHG
#0100
3. The set value can be changed from the above display.
Changing Constants
Input the constant from the above display.
CONT
1 2 0 WRITE WRITE
#
ONLINE EDIT?
SV #0120
000202 CT00
WRITE
LD 000100
Changing Word Address
Input the word address from the above display.
CH
SHIFT
*DM 1 0 WRITE WRITE
ONLINE EDIT?
SV 0010
109
000202 CT00
WRITE
LD 000100
Timer/Counter SV Change 2: Fine Adjustment of Constant

This operation is used to increment or decrement the set value of a timer/
counter with a constant specified for the set value in the user program.
Key Sequence
↓
Timer/counter SV display CHG CHG CLR CLR WRITE WRITE
Operation Example The following example describes how to adjust the constant specified as the
set value for TIM 0001.
1,2,3... 1. From the initial display, access the timer/counter for which the set value will
be adjusted.
000000 CT00
CLR
¡
CF 000201 CT00 FIND

TIM 1 SRCH TIM 0001
000201 TIM
↓ SV #0020
2. Specify changing the set values from the above display.
000201SV U/D?
CHG CHG
#0020
3. Incremented or decremented the constant using the Up and Down Keys.
↑ 000201SV U/D?
↓
or #0021
Incremented for the

↓ Down Key.
Decremented for the
↑ Up Key.
4. Exit the operation. The new set value will be displayed.
ONLINE EDIT?
CLR CLR WRITE
SV #0021
000202 CT00
WRITE
LD 000100
110
SECTION 6
Maintenance Operations
This section includes information on reading and setting the clock, reading cycle time, and reading and clearing error
messages.
6-1 Clock Read/Change. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112

6-2 Cycle Time Read. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113
6-3 Reading/Clearing Error Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114
111
Clock Read/Change Section 6-1
6-1 Clock Read/Change

RUN MONITOR PROGRAM
See note OK OK
Note When the CPU Unit is in RUN mode, the clock can be read but can-
not be changed.
This operation is used to read or set the CPU Unit’s internal clock.
• A battery is not installed in CS1-series PCs when they are shipped. When
the battery is installed in the CPU Unit, the CPU Unit clock will read as
shown below. 00–01–00 = day, month, year; 00:00:00 = hours, minutes,
seconds; SUN(0) = Sunday.
TIM 00-00-00
00:00:00: SUN(0)
• The CPU Unit’s internal clock will start when the following Clock Read/
Change operation is executed, when the time is read/changed from
another Peripheral Device, when a FINS command is used to read/
change the time, or when the DATE instruction is executed from the user
program.
• The time data for the CPU Unit’s internal clock is stored in the Calendar/
Clock Area (A351 to 354) in the Auxiliary Area.
Key Sequence
Initial display FUN SHIFT MON 0 CHG ↑ Data WRITE
↓
Specify: Yr Mth Day Hr Min S
Operation Example The following example shows how to set clock data for the first time.
1,2,3... 1. From the initial display, access the special function display.
000000 CT00
CLR
¡
SHIFT MON
0:CLOCK
FUN
2. Select 0: TIM.
TIM 00-01-01
0
00:00:00: SUN(0)
3. To change the settings, press the CHG Key. When the CHG Key is
pressed, the cursor will be displayed on the digit to be changed.
112
Cycle Time Read Section 6-2
Last 2 digits of A.D. Days: 01 to 31

calendar year: Months: 01 to 12
00 to 99.
CHG CHG TIM?98-04-03

14:25:58 FRI(5)
Hour Seconds
00 to 23 00 to 59
Minutes Days
00 to 59 Sun to Sat (0 to 6)
Key Functions
↓
:Moves the cursor to the right.
↑
:Moves the cursor to the left.
0 9
to : Input numeric values.
4. Press the WRITE Key when the time and date have been set.
TIM 98-04-03
WRITE
14:25:58 FRI(5)
5. Press the CLR Key to exit.
6-2 Cycle Time Read

RUN MONITOR PROGRAM
OK OK No
This operation is used to display the average cycle time for all programs (the
total of all tasks) that are being executed.
Key Sequence
Initial display MON MON
Operation Example
1,2,3... 1. From the initial display, access the cycle time display.
000000 CT00
CLR
¡
MON
000000CYCLE TIM
112.1MS
Average cycle time for all programs.

Refreshed in real-time.
113
Reading/Clearing Error Messages Section 6-3
6-3 Reading/Clearing Error Messages

RUN MONITOR PROGRAM
OK OK OK
This operation is used to read fatal and non-fatal error messages, to read
messages generated by MSG(046), and to reset error displays.
Key Sequence
Initial display FUN MON MON
Initial display FUN MON ↓ ↓
Note 1. Fatal operating errors can only be displayed and reset in PROGRAM
mode.
2. If the source of the error is not removed, the error will not be reset and the
error message will continue to be displayed.
3. When errors are read using the Down Key, the error will not be reset and
current errors can be confirmed.
Operation Example
1,2,3... 1. If there is no error, CHK OK will be displayed (and the error read operation
will be finished).
000000 CT00
CLR
000000
FUN
FUN (???)
MON
ERR/MSG
CHK OK
2. If there is an error, the following will be displayed. The example below
shows a memory error.
MEMORY ERR
3. If there are several errors, the next most serious error will be displayed
when the MON Key is pressed. (The order of display is given on the follow-
ing pages.)
MON
CYCLE TIME ERR
4. If the Message Display Instruction MSG(046) has been executed to record

error messages, the recorded messages will be displayed when the MON
Key is pressed. These messages will be displayed only after all other error
messages have been displayed.
114
Note If the FAL instruction has being executed, messages recorded for the
MSG(046) instruction will not be displayed until the cause of FAL ex-
ecution has been removed.
MON
MSG
MATERIAL SHORT
5. When all error messages and MSG(046) messages have been cleared,
the following message will be displayed.
MON
ERR/MSG
CHK OK
Error Messages
When CPU Unit operation is not possible, the following message will be dis-
played.
CPU WAIT'G
When several errors have occurred at the same time, the error messages will
be displayed in order from 1 to 21, as listed below. (In order from the most
serious to least serious.)
Fatal Operating Errors
1,2,3... 1. Memory Error
MEMORY ERR
2. I/O Bus Error

Rack No.
I/O BUS ERR f
3. Unit Number Duplication Error
UNIT No. DPL ERR
RACK No. DPL ERR
4. Fatal Inner Board Error
FATAL INNER ERR
5. Too Many I/O Points
TOO MANY I/O PNT
6. I/O Setting Error
I/O SET ERR
115
7. Program Error
PROGRAM ERR
8. Cycle Time Error
CYCLE TIME ERR
9. System Error (FALS)

FAL No.
SYS FAIL FALS
Non-fatal Operating Errors 10. System Error (FAL)

FAL No.
SYS FAIL FAL
11. Interrupt Error
INTRPT ERR
12. High-density I/O Error
DENSITY I/O ERR
13. PC Setup Error
PC SETUP ERR
14. I/O Verification Error
I/O VRFY ERR
15. Non-fatal Inner Board Error
NO-FTL INNER ERR
16. CS1 CPU Bus Unit Error

Unit No.
CPU BU ERR
17. Special I/O Unit Error

Unit No.
SIOU ERR
116
18. SYSMAC Bus Unit Error

RM No.
SYSBUS ERR
19. Battery Error
BATT LOW
20. CS1 CPU Bus Unit Setup Error

Unit No.
CPU BU STUP
21. Special I/O Unit Setup Error

Unit No.
SIOU SETUP
MSG(046) Messages
The MSG(046) instruction can be used to record up to 8 messages for display
on the Programming Console. These messages will be displayed when the
MON Key is pressed after all other error messages have been displayed. If
more than one MSG(046) instruction has been executed, the following meth-
ods can be used to display the other MSG(046) messages.
• Press the MON Key continuously. The currently displayed message will
be cleared and the next message will be displayed.
• Press the Down Key continuously. The currently displayed message will
not be cleared and the next message will be displayed.
Using the MSG(046)

Instruction
MSG
Operands
N N: Message Number
0 to 7
M
M: 1st Message Word
The address of the first word containing the
message to be displayed.
Specify a constant (0000 to FFFF Hex) to
clear the message.
MSG(046) Instruction
The MSG(195) instruction reads sixteen words of extended ASCII contained
in 16 words from M to M+15 and displays the message on a Peripheral Device
(e.g., the Programming Console). The displayed message can be up to 32
characters long, i.e., each ASCII character code requires eight bits (two dig-
its).
117
Storage Words
(Leftmost) (Rightmost)
M 4D 41
M+1 54 45
M+2 52 49
M+3 41 4C MSG
MATERIAL SHORT
M+4 20 53
M+5 48 4F
M+6 52 54
Note Data will be displayed in order from the leftmost byte to the
rightmost byte on the Programming Console display.
Note Error messages will not be displayed while the error is occurring.
118
SECTION 7
Memory Card Operations
This section provides information on how to format Memory Cards before use, and procedures for transferring data
between Memory Cards and the CPU Unit.
7-1 File Memory Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120

7-2 Memory Card Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121
7-3 File Write. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122
7-4 File Read . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126
7-5 File Verify . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130
7-6 File Delete . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133
119
File Memory Operations Section 7-1
7-1 File Memory Operations

File memory operations read/write CPU Unit file memory (Memory Card or
EM File Memory. It is possible to read/write the following types of data.
• All user programs
• I/O memory areas
• Parameter Areas (e.g., PC Setup)
Note I/O name table and block comments cannot be saved to file memory.
File Memory Types

Memory type Data recognized by Memory capacity Model
CPU Unit
Memory Card (flash memory) 1. UM Area 8 Mbytes HMC-EF861
2. I/O memory within
specified ranges 15 Mbytes HMC-EF171
3. Parameter Areas (e.g.,
PC Setup)
30 Mbytes HMC-EF371
4. I/O name table (See
note)
5. Block comments (See
note)
EM File Memory (RAM) 1. UM Area From the specified ---
EM area 2. I/O memory within EM bank to the
Bank 0 specified ranges last bank (as spec-
:
ified in PC Setup).
3. Parameter Areas (e.g.,
Bank n PC Setup)
EM File Memory
: (From bank n 4. I/O name table (See
Bank C onwards.) note)
5. Block comments (See
note)
Note I/O name table files (extension .SBL) and block comment files (extension
.RGL), cannot be handled from the Programming Console.
For details on how to specify the starting bank for EM area file memory, refer
to Section Section 8 PC Setup Procedure.
Overview of Memory Card/EM File Memory Operations

Operation Details
Memory Card Format Formats Memory Cards or EM ---
File Memory.
File Write Transfers files from the PC to a See note.
Memory Card or EM File Mem-
ory.
File Read Transfers files from a Memory
Card or EM File Memory to the
PC.
File Verify Compares Memory Card or EM
File Memory data with CPU Unit
internal data.
File Delete Deletes the contents of Memory
Card or EM File Memory data.
120
Memory Card Format Section 7-2
Note The memory areas that can be transferred or deleted are as follows:
UM Area
I/O memory CIO Area Specify the transfer start
Work Area (WR) address and end address for
each memory area.
Holding Bit Area (HR)
Note One area = 1 file
Auxiliary Bit Area (AR)
DM Area (DM)
EM Area (EM)
Parameter Areas (e.g., PC Setup)
With CS1-series PCs, Memory Cards and the specified range of EM File
Memory can be used as file memory. Regardless of whether it’s the UM Area,
I/O memory or the Parameter Areas (e.g., PC Setup), all data is saved as
files.
CPU Unit
Memory area
UM Area
File memory
CIO
xxxxxxxx.OBJ
Memory Card
HR
WR xxxxxxxx.IOM
I/O memory
AR
DM xxxxxxxx.STD EM File
Memory
EM
Parameter Areas
(PC Setup, I/O
tables, etc.)
7-2 Memory Card Format

RUN MONITOR PROGRAM
OK OK OK
This operation is used to format Memory Cards or EM File Memory.
Key Sequence
CONT
Initial display FUN SHIFT ↓ 2 Password WRITE
#
Fixed: 9713 (Memory Card)
8426 (EM File Memory)
Operation Example
1,2,3... 1. From the initial display, access the Memory Card operations menu.
000000 CT00
CLR
¡
121
File Write Section 7-3
SHIFT
CONT 0:XFER
FUN
# 1:VRFY
2:FORMAT
↓ 3:DEL
2. Select 2: FORMAT.
FORMAT?
2
???? **
3. To format a Memory Card, enter the password.
WRITE
FORMAT'G ~
9 7 1 3
9713 CF
Enter the password. (See note.)
FORMAT END
9713 CF
Note “9713” is a password set by the system for I/O Table Create and
Memory Card Format. It cannot be changed.
4. To format EM File Memory, enter the password.
WRITE
FORMAT'G ~
8 4 2 6
8426 EM
Enter the password. (See note.)
FORMAT END
8426 EM
Note “8426” is a password set by the system for EM File Memory Format.
It cannot be changed.
7-3 File Write

RUN MONITOR PROGRAM
OK OK OK
This operation transfers the UM Area, specified I/O memory area range, or
PC Setup data from the CPU Unit to a Memory Card or EM File Memory.
Key Sequence
↓
CONT
Initial display FUN SHIFT 0 0 WRITE
#
↑
Transfer start address ↓ Transfer end address WRITE File name WRITE
Operation Example In the following example, CIO 2345 to CIO 2446 in the CIO Area of the CPU
Unit are transferred to a Memory Card as the file “SAMPLE.IOM.”
122
Note For creation (and transfer to a Memory Card) of an AUTOEXEC file (a file that
automatically transfers data when the power is turned ON), refer to page 125.
000000 CT00
CLR
¡
SHIFT
CONT 0:XFER
FUN
# 1:VRFY
2. Select 0:XFER to bring up the Memory Card operations menu.
0:PC~CF_CARD
0
1:CF_CARD~PC
3. Select 0: PC CF_CARD.
PC~CF_CARD?(OBJ)
0
XFER TYPE UM<
4. Select CIO as the type of data to be transferred.
PC~CF_CARD?(IOM)
↓
XFER TYPE CIO<
PC~CF_CARD? CIO
WRITE
ST 0000ED 6143
Transfer start Transfer end

address address
5. Use the Up and Down Keys to select the type of data to be transferred.
UM Area
PC~CF_CARD?(OBJ)
XFER TYPE UM<
CIO Area
PC~CF_CARD?(IOM)
↑ ↓ XFER TYPE CIO<
or
Holding Bit Area
PC~CF_CARD?(IOM)
↑ ↓ XFER TYPE HR<
or
Work Bit Area
PC~CF_CARD?(IOM)
↑ ↓ XFER TYPE WR<
or
Auxiliary Bit Area
PC~CF_CARD?(IOM)
↑ ↓ XFER TYPE AR<
or
123
DM Area
PC~CF_CARD?(IOM)
↑ ↓ XFER TYPE DM<
or
EM Area
PC~CF_CARD?(IOM)
↑ ↓ XFER TYPE EM0_<
or
Parameter Areas (PC Setup)
PC~CF_CARD?(STD)
↑ ↓ XFER TYPE STD<
or
Note a) When saving I/O memory areas, each area (CIO Area, Holding Bit
Area, Work Area, Auxiliary Area, DM Area or EM Area) is saved to
a separate file (extension .IOM) within the specified word range.
b) Always select DM< when creating a data file that is automatically
transferred when the power is turned ON (AUTOEXEC.IOM).
c) If EM0_ is displayed, input the number of the EM bank from 0 to C.
d) The Parameter Areas include the PC Setup, registered I/O tables,
routing tables, and CPU Bus Unit Setup.
6. When CIO, HR, WR, AR, DM, or EM@ data is being transferred, specify
the transfer start word address and the transfer end word address.
Transfer start address: CIO 2345
2 3 4 5
PC~CF_CARD? CIO
ST 2345 ED 6143
Transfer start address
PC~CF_CARD? CIO
↓
ST 2345 ED 6143
Transfer end address: CIO 2446
2 4 4 6 PC~CF_CARD? CIO
ST 2345 ED 2446
Transfer end address
WRITE
PC~CF_CARD?(IOM)
FILE"0:~ "
0: Memory Card
1: EM File Memory
7. Switch to text input mode to enter the file name.
SHIFT
TEXT PC~CF_CARD?(IOM!
!
FILE"0:~ "
Text input mode
8. When saving data to a Memory Card, input the file name. When inputting
the name from the Programming Console, A to Z and 0 to 9 are available.
The file name may be a maximum of 8 characters. In the following exam-
ple, the file name is SAMPLE.
124
*EM_
EM_/EXT FUN AA EM AR DR PC~CF_CARD?(IOM!
S A LDM DM P HR L IR
E FILE"0:SAMPLE~ "
It is not necessary to input the file extension (.OBJ for UM Area, .IOM for
memory areas within I/O memory, and .STD for Parameter Areas). The ex-
tension will be automatically added.
Transfer type Extension
OBJ (UM area) .OBJ
CIO, HR, AR, DM, EM@_ .IOM
STD (PC Setup) .STD
• Press the Up and Down Keys to move the cursor.

• Change the “0” in the file name to “1” to transfer the file to EM File
Memory instead of to the Memory Card.
• Press the CF/SRCH Key to display the file names already on the Mem-
ory Card or EM File Memory. In this case steps 7, 8, and 9 are not nec-
essary.
CF CF_CARD~PC?(IOM)
SRCH FILE"0:SAMPLE "
9. Return to normal input mode.
PC~CF_CARD?(IOM)
CLR
FILE"0:SAMPLE~ "
10. Execute the save by pressing the WRITE Key.
PC~CF_CARD? END
WRITE
FILE"0:SAMPLE "
When a file with the same extension and file name already exists on the
Memory Card, the following display will appear.
PC~CF_CARD OVER?
FILE"0:SAMPLE "
11. Use the following procedure to overwrite the existing file on the Memory
Card.
PC~CF_CARD END
WRITE
FILE"0:SAMPLE "
• If you do not want to overwrite the existing file, press the CLR Key and
input a different file name.
• If the volume label or directory name is specified by mistake, a message
will ask if you want to overwrite. If this happens, press the CLR Key and
input the proper file name.
Precautions when Creating AUTOEXEC Files

(Files that automatically transfer data when the power is turned ON.)
1. The filename must be “AUTOEXEC.”
The following files can be created from the Programming Console and saved
to a Memory Card. These files automatically transfer data when the power is
turned ON. The filename however, must always be AUTOEXEC.
125
File Read Section 7-4
Program file: AUTOEXEC.OBJ

Parameter file: AUTOEXEC.STD
Data file: AUTOEXEC.IOM
2. For AUTOEXEC.IOM, the transfer type must be “DM” and the start
address must be 20000.
When creating AUTOEXEC.IOM, Data Memory (DM) must be selected as the
transfer type before transfer. Also, the start address must be set to 20000.
Operation: Select “DM<” as the transfer type and “20000” as the transfer start
address.
When the power is turned ON, AUTOEXEC.IOM files will be read from the
Memory Card and all data from the start of the file will be transferred to the
Data Memory area, starting at D20000.
AUTOEXEC.IOM DM Area
D20000
onwards
Automatically
transferred at
power ON.
Note DM< must be selected as the transfer type.

20000 must be selected as the start address.
Note When creating an AUTOEXEC.IOM file, be sure to set the start address to
D20000.
It is possible to create AUTOEXEC.IOM files without setting the start address
to D20000. The actual destination of data transferred from the Memory Card
when the power is turned ON, however, will be the (fixed) address starting at
D20000. Do not set the area type or the start address, therefore, to anything
other than D20000.
7-4 File Read

RUN MONITOR PROGRAM
No See note OK
This operation is used to transfer UM Area, specified I/O memory areas, or

PC Setup data from a Memory Card or EM File Memory to the CPU Unit.
!Caution Always confirm safety before reading I/O memory data from a Memory Card
even when working in PROGRAM mode. The CPU Unit will refresh I/O even
in PROGRAM mode. If the status of a bit allocated to an Output Unit, Special
I/O Unit, or CPU Bus Unit is changed, the load connected to the Unit may
operate unexpectedly.
Key Sequence
↓
CONT WRITE
Initial display FUN SHIFT
# 0 1
↑
Transfer start address ↓ Transfer end address WRITE File name WRITE
126
Operation Example In the following example, a file on the Memory Card, SAMPLE.IOM, is trans-
ferred to CIO 2345 to CIO 2446 in the CPU Unit.
000000 CT00
CLR
¡
FUN SHIFT
CONT 0:XFER
# 1:VRFY
2. Select 0: XFER from the Memory Card operations menu.
0:PC~CF_CARD
0
1:CF_CARD~PC
3. Select 1: CF_CARD PC.
CF_CARD~PC?(OBJ)
1
XFER TYPE UM<
4. Select CIO as the type of data to be transferred.
CF_CARD~PC?(IOM)
↓ XFER TYPE CIO<
WRITE
CF_CARD~PC? CIO
ST 0000ED 6143
Transfer start Transfer end

address address
5. Use the Up and Down Keys to select the type of data to be transferred.
UM Area
CF_CARD~PC?(OBJ)
XFER TYPE UM<
CIO Area
CF_CARD~PC?(IOM)
↑ ↓ XFER TYPE CIO<
or
Holding Bit Area
CF_CARD~PC?(IOM)
↑ ↓ XFER TYPE HR<
or
Work Bit Area
CF_CARD~PC?(IOM)
↑ ↓ XFER TYPE WR<
or
Auxiliary Bit Area
CF_CARD~PC?(IOM)
↑ ↓ XFER TYPE AR<
or
127
DM Area
CF_CARD~PC?(IOM)
↑ ↓ XFER TYPE DM<
or
EM Area (See note)
CF_CARD~PC?(IOM)
↑ ↓ XFER TYPE EM0_<
or
Parameter Areas
CF_CARD~PC?(STD)
↑ ↓ XFER TYPE STD<
or
Note If EM0_ is displayed, input the number of the EM bank from 0 to C.
the transfer start word address and the transfer end word address. The
start and end words are specified only when I/O memory is being trans-
ferred.
Transfer destination start address: CIO 2345
3 4
CF_CARD~PC? CIO
2 5
ST 2345ED 6143
Transfer destination start address
CF_CARD~PC? CIO
↓ ST 2345ED 6143
Transfer destination end address: CIO 2446
4 4
CF_CARD~PC? CIO
2 6
ST 2345ED 2446
Transfer destination end address
WRITE CF_CARD~PC?(IOM)
FILE"0:~ "
0: Memory Card
1: EM File Memory
7. Switch to text input mode to enter the name of the file to transfer to the CPU
Unit. (See note.)
SHIFT
TEXT CF_CARD~PC?(IOM!
! FILE"0:~ "
Note The data area to which data is being written does not necessarily have to be
the same as the area from which data was originally read. The data will be
transferred.
128
Memory Card file Transfer destination data

XXXXXXXX.IOM area in CPU Unit.
Transfer destination
start address
Transfer destination end

address
E.g.: DM Area data E.g.: CIO Area
It is essential, however, that the number of words in the original transfer file be
greater than or equal to the number of words in the transfer destination area,
as shown below. Any words which exceed the transfer destination area will not
be transferred.
No. of words in Memory Card No. of words in CPU Unit
original transfer file transfer destination area
Transfer destination
start address
Transfer destination end
address
Not transferred
If the number of words in the original transfer file is less than the number of
words in the specified transfer destination area, no data will be transferred.
No data will be transferred.
8. Enter the file name. In the following example, the file name is SAMPLE.
*EM_
EM_/EXT FUN AA EM AR DR CF_CARD~PC?(IOM!
E FILE"0:SAMPLE~ "
• Change the “0” in the file name to “1” to transfer the file from EM File
Memory instead of the Memory Card.
Note Press the CF/SRCH Key to display the file names on the Memory
Card or EM File Memory. If this function is used, steps 7., 8., and 9.
are not necessary.
CF CF_CARD~PC?(IOM)
CF_CARD~PC?(IOM)
CLR
FILE"0:SAMPLE~ "
10. Execute the transfer by pressing the WRITE Key.
CF_CARD~PC END
WRITE
FILE"0:SAMPLE "
Reading Memory Card data using the Programming Console is useful, for
example, to make changes to a program by taking only a Memory Card and
Programming Console on-site.
1. Save the program file (XXXXXXXX.OBJ) using the CX-Programmer.
2. Take the Memory Card on-site and install it in the CPU Unit.
129
File Verify Section 7-5
3. Connect the Programming Console, and transfer the program file from the
Memory Card to the CPU Unit.
Memory Card
7-5 File Verify

RUN MONITOR PROGRAM
OK OK OK
This operation verifies data on a Memory Card or EM File Memory (UM Area,
specified I/O memory areas, or PC Setup) with internal CPU Unit data.
Key Sequence
↓
CONT
# 1 WRITE
Verify start address ↓ Verify end address WRITE File name VRFY
Operation Example In the following example, CIO 2345 to CIO 2446 in the CPU Unit are verified
against the Memory Card file “SAMPLE.IOM.”
000000 CT00
CLR
¡
SHIFT
CONT 0:XFER
FUN
# 1:VRFY
2. From the Memory Card operations menu, select 1: VRFY.
VRFY? (OBJ)
1
VRFY TYPE UM<
130
3. Specify CIO as the type of memory to be verified.
VRFY? (IOM)
↓ VRFY TYPE CIO<
VRFY? CIO
WRITE
ST 0000ED 6143
Verify start Verify end

address address
4. Use the Up and Down Keys to select the type of data to be verified.
UM Area
VRFY? (OBJ)
VRFY TYPE UM<
CIO Area
VRFY? (IOM)
↑ ↓ VRFY TYPE CIO<
or
Holding Bit Area
VRFY? (IOM)
↑ ↓ VRFY TYPE HR<
or
Work Bit Area
VRFY? (IOM)
↑ ↓ VRFY TYPE WR<
or
Auxiliary Bit Area
VRFY? (IOM)
↑ ↓ VRFY TYPE AR<
or
DM Area
VRFY? (IOM)
↑ ↓ VRFY TYPE DM<
or
EM Area
VRFY? (IOM)
↑ ↓ VRFY TYPE EM0_<
or
Parameter Areas
VRFY? (STD)
↑ ↓ VRFY TYPE STD<
or
the transfer start word address and the transfer end word address. The
start and end words are specified only when I/O memory is being trans-
ferred.
Verify start address: CIO 2345
131
VRFY? CIO
2 3 4 5
ST 2345ED 6143
Verify start address
VRFY? CIO
↓ ST 2345ED 61430
Verify end address: CIO 2446
4 4
VRFY? CIO
2 6
ST 2345ED 2446
Verify end address
WRITE
VRFY? (IOM)
FILE"0:~ "
0: Memory Card
1: EM File Memory
SHIFT
TEXT VRFY? (IOM!
! FILE"0:~ "
7. Enter the file name. In this example the file name is 0: SAMPLE.
*EM_
EM_/EXT FUN AA EM AR DR VRFY? (IOM!
E FILE"0:SAMPLE~ "
• Change the “0” in the file name to “1” to verify the file to a file in EM File
Memory instead of the Memory Card.
are not necessary.
CF VRFY? (IOM)
VRFY? (IOM)
CLR
FILE"0:SAMPLE~ "
9. Execute the verification by pressing the VRFY Key.
OK: Files are the same
NG: Files are different.
VRFY? OK (IOM)
VRFY
FILE"0:SAMPLE "
132
File Delete Section 7-6
7-6 File Delete

RUN MONITOR PROGRAM
OK OK OK
The operation deletes data from a Memory Card or EM File Memory (UM
Area, specified I/O memory areas, PC Setup).
Key Sequence
↓
CONT
# 3 WRITE
File name WRITE WRITE
Operation Example In the following example, the Memory Card file “SAMPLE.IOM” is deleted.
000000 CT00
CLR
¡
SHIFT
CONT 0:XFER
FUN
# 1:VRFY
2:FORMAT
↓ 3:DEL
2. From the Memory Card operations menu, select 3:DEL.
DEL ? (OBJ)
3
DELETE TYPE UM<
3. Select CIO as the type of data to be deleted.
DEL ? (IOM)
↓ DELETE TYPE CIO<
WRITE
DEL ? (IOM)
FILE"0:~ "
0: Memory Card
1: EM File Memory
4. Use the Up and Down Keys to select the type of data to be deleted.
UM Area
DEL ? (OBJ)
DELETE TYPE UM<
CIO Area
DEL ? (IOM)
↑ ↓ DELETE TYPE CIO<
or
133
Holding Bit Area
DEL ? (IOM)
↑ ↓ DELETE TYPE HR<
or
Work Bit Area
DEL ? (IOM)
↑ ↓ DELETE TYPE WR<
or
Auxiliary Bit Area
DEL ? (IOM)
↑ ↓ DELETE TYPE AR<
or
DM Area
DEL ? (IOM)
↑ ↓ DELETE TYPE DM<
or
EM Area
DEL ? (IOM)
↑ ↓ DELETE TYPEEM0_<
or
Parameter Areas
DEL ? (STD)
↑ ↓ DELETE TYPE STD<
or
SHIFT
TEXT DEL ? (IOM!
! FILE"0:~ "
6. Enter the file name. (See note.)
*EM_
EM_/EXT FUN AA EM AR DR DEL ? (IOM!
E FILE"0:SAMPLE~ "
• Change the “0” in the file name to “1” to delete a file from EM File Mem-
ory instead of the Memory Card.
are not necessary.
File name search:
CF DEL ? (IOM)
DEL ? (IOM)
CLR
FILE"0:SAMPLE~ "
134
8. Confirm the file to be deleted.
DEL OK? (IOM)

WRITE
FILE"0:SAMPLE "
9. Execute the deletion by pressing the WRITE Key.
DEL END (IOM)

WRITE
FILE"0:SAMPLE "
135
SECTION 8
PC Setup Procedure
This section lists the settings in the PC Setup.
8-1 PC Setup Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138
137
PC Setup Procedure Section 8-1
8-1 PC Setup Procedure

RUN MONITOR PROGRAM
See note See note OK
Note When in RUN or MONITOR mode, contents of settings can be read, but set-
ting cannot be performed.
This operation is used to read and write data from and to the PC Setup Area
in the CPU Unit.
Key Sequence
FUN VRFY CHG Set value WRITE
1 Address ↓
Operation Example 1 In the following example, the Startup mode setting (+081) is changed.
1,2,3... 1. From the initial display, access the PC Setup display.
000000 CT00
CLR
¡
PC SETUP
FUN VRFY
0:MODE 1:PC SYS
2. It is not necessary to input the Startup mode setting address, just select
0:MODE.
0
PC SETUP
+081 PRCN
PC Setup address
(+081: Startup mode
changes) Current settings are displayed
(Corresponds to the operation
mode of the Programming Con-
sole.)
3. Make changes to the settings.
CHG
PC SETUP ?
+081 PRCN PRCN
Possible changes are
displayed in sequence
PC SETUP ?
↓ +081 PRCN PRG
PC SETUP ?
↓ +081 PRCN MON
PC SETUP ?
↓ +081 PRCN RUN
138
Press the Up or Down Keys to display each mode in sequence.

PRCN PRG MON RUN
(Corresponds to the
Program mode Monitor mode Operation mode
operation mode
switch on the Pro
gramming Console)
PC SETUP
WRITE
+081 RUN
4. Press the CLR Key to return to the PC Setup display.
CLR
PC SETUP
0:MODE 1:PC SYS
Operation Example 2 In the following example, the cycle time monitoring time is changed to 2,000
ms (2 s).
1. From the initial display, access the PC Setup display.
000000 CT00
CLR
PC SETUP
FUN VRFY
0:MODE 1:PC SYS
2. To make changes to all settings except the Startup mode, select 1:PC
SETUP, specify the address (from + onwards), and read the set value.
Example: Changing cycle time monitoring time
PC SETUP
1
+000 0000
C
0
PC SETUP
2 9
+209
PC Setup address
(+209: Cycle time monitoring time)
↓ PC SETUP
+209 0000
Set value
When the set value is displayed, pressing the Up or Down Keys will display
the previous or next address.
3. Use the following procedure to change the set word.
PC SETUP ?
CHG
+209 0000 0000
139
Example: Changing the value to 2,000 ms.
C PC SETUP ?
8 0 SHIFT 2 8
+209 0000 80C8
PC SETUP
WRITE
+209 80C8
4. Press the CLR Key to return to the PC Setup display.
140
Appendix A
ASCII Coding Sheet
The following list shows the range of characters that can be displayed on the Programming Console. Symbols
and Japanese “katakana” characters however, cannot be input from the Programming Console.
Right- Leftmost bit
most 0, 1, 2 3 4 5 6 7 A B C D E F
bit 8, 9
0 # 3 C S # 3 C S
1 $ 4 D T $ 4 D T
2 j % 5 E U % 5 E U
3 & 6 F V & 6 F V
4 ' 7 G W ' 7 G W
5 ( 8 H X ( 8 H X
6 ) 9 I Y ) 9 I Y
7 l * : J Z * : J Z
8 + ; K [ + ; K [
9 , < L \ , < L \
A - = M ] - = M ]
B . > N ^ . > N ^
C / ? O _ / ? O _
D 0 @ P ` 0 @ P `
E ! 1 A Q a ! 1 A Q
F " 2 B R e " 2 B R a
141
Appendix B
Error Messages
Error messages will be displayed on the Programming Console, whenever an operating error is made. Refer to
the following table for operating errors and their remedies.
Error message Remedy
CHK MEM (ROM) Pin 1 on the CPU Unit’s DIP switch is set to ON (write protect). Reset this pin
to OFF (write enabled).
PRGM OVER The last address is not NOP, therefore no more of the program can be input.
Clear the program after the END instruction.
ADR OVER The set address exceeds the last address in the UM Area. Reset the address.
I/O No. ERR I/O data has been input outside the permissible range. Reconfirm the input
ranges for all instructions and input again correctly.
Refer to 6-3 Reading/Clearing Error Messages for information on displaying the error status of the PC.
143
Appendix C
PC Setup Setting Sheets
Address
+10 @@@@
Value (Hex) Rack 0, Slot 0

I/O response time
00 8 ms
10 No filter
11 0.5 ms
12 1 ms
13 2 ms
14 4 ms
15 8 ms
16 16 ms
17 32 ms
Rack 0, Slot 0
Value (Hex) I/O response time
00 to 17 As above
Address
+11 @@@@

I/O response time
00 to 17 As above
Rack 0, Slot 3
00 to 17 As above
Address
+49 @@@@

I/O response time
00 to 17 As above
Rack 7, Slot 9
00 to 17 As above
Note For the CJ-series PCs, address go only to address +29 (3 Racks only).
Address
+80 @@@@
Value (Hex) IOM Hold Bit status Forced Status Hold

at startup Bit at startup
C000 Retained Retained
8000 Retained Cleared
4000 Cleared Retained
0000 Cleared Cleared
145
PC Setup Setting Sheets Appendix C
Address
+81 @@@@
Value Startup mode

PRCN Mode on Programming Console's mode switch
PRG PROGRAM mode
MON MONITOR mode
RUN RUN mode
Note PRCN, PRG, MON, and RUN can be selected

using the Up and Down Keys.
Address
+83 @@@@ (CS1-H/CJ1-H CPU Units only)
Value (Hex) RUN Enable Setting

8000 Enabled (Operation will start.)
0000 Disabled (Operation will not start.)
Address
+84 @@@@ (CS1-H CPU Units only)
Value (Hex) Special Inner Board Setting

8000 Special Inner Board Setting enabled.
0000 Special Inner Board Setting disabled.
Address
+128@@@@
Value (Hex) Detect Low Battery Detect Interrupt

Task Error
C000 Do not detect Do not detect
8000 Do not detect Detect
4000 Detect Do not detect
0000 Detect Detect
Address
+129 @@@@ (CS1-H/CJ1-H CPU Units only)
Value (Hex) Error History Storage of FAL

8000 Do not store FAL in error history.
0000 Store FAL in error history.
Address
+136@@@@
Value (Hex) EM file memory settings

0000 None
0080 EM File Memory Enabled: Bank No. 0
0081 EM File Memory Enabled: Bank No. 1
to
008C EM File Memory Enabled: Bank No. C
146
Address
+144@@@@
Peripheral port
Value (Hex) Data bits Stop bits Parity
00 7 bits 2 bits Even
01 7 bits 2 bits Odd
02 7 bits 2 bits None
0A 8 bits 2 bits None
0C 8 bits 1 bits Even
0D 8 bits 1 bits Odd
0E 8 bits 1 bits None
Value (Hex) Communications mode

00 Default (The above 3 columns
are disabled)
80 Host link
82 NT link
84 Peripheral bus
85 Host link
Address
+145 @@@@
Peripheral port
Value (Hex) Baud rate
0000 9,600 bps
0001 300 bps
0002 600 bps
0003 1,200 bps
0004 2,400 bps
0005 4,800 bps
0006 9,600 bps
0007 19,200 bps
0008 38,400 bps
0009 57,600 bps
000A 115,200 bps
Note For NT Links: 0000 to 0009 Hex = Normal NT Link, 000A = High-speed NT Link.
Address
+147@@@@
Peripheral port
Value (Hex) Host link Unit No.
0000 No. 0
0001 No. 1
to to
001F No. 31
Address
+150@@@@
Peripheral port
Value (Hex) Maximum Unit No. in NT Link Mode
0000 No. 0
0001 No. 1
to to
0007 No. 7
147
Address
+160@@@@
RS-232C Port
Value (Hex) Data bits Stop bits Parity
0A 8 bits 2 bits None
0C 8 bits 1 bits Even
0D 8 bits 1 bits Odd
0E 8 bits 1 bits None
Value (Hex) Communications mode

00 Default (The above 3 columns
are disabled)
80 Host link
82 NT link
83 No-protocol
84 Peripheral bus
85 Host link
Address
+161@@@@
RS-232C port
Value (Hex) Baud rate
0000 9,600 bps
0001 300 bps
0002 600 bps
0003 1,200 bps
0004 2,400 bps
0005 4,800 bps
0006 9,600 bps
0007 19,200 bps
0008 38,400 bps
0009 57,600 bps
000A 115,200 bps
Note For NT Links: 0000 to 0009 Hex = Normal NT Link, 000A = High-speed NT Link.
Address
+162@@@@
RS-232C port
Value (Hex) No-protocol mode delay
0000 0 ms
0001 10 ms
to to
270F 99,990 ms
Address
+163@@@@
RS-232C port
Value (Hex) Host link Unit No.
0000 No. 0
0001 No. 1
0002 No. 2
to to
001F No. 31
148
Address
+164@@@@
RS-232C Port
Value (Hex) No-protocol Mode end code
00 00
to to
FF FF
Value (Hex) No-protocol Mode end code

00 00
to to
FF FF
Address
+165@@@@
RS-232C Port
Value (Hex) No-protocol Mode reception data volume
00 256
01 1
to to
FF 256
Value (Hex) No-protocol Mode end code setting

0 None (Specify the amount of data being received)
1 Yes (Specify the end code)
2 End code is set to CR+LF
Value (Hex) No-protocol Mode start code setting

0 None
1 Yes
Address
+166@@@@
RS-232C port
Value (Hex) Maximum Unit No. in NT Link Mode
0000 No. 0
0001 No. 1
to to
0007 No. 7
Address
+195@@@@
Value (Hex) Scheduled interrupt time units

0000 10 ms
0001 1.0 ms
Address
+197@@@@
Value (Hex) Instruction error operation

0000 Continue operation
8000 Stop operation
149
Address
+198@@@@ (CS1-H/CJ1-H CPU Units only)
Value (Hex) Com Port for Background Processing

0 to 7 Communications port 0 to 7 (logic port)
Value (Hex) Background Processes

Table data Text string Data shifting
instructions instructions instructions
E00 Yes Yes Yes
C00 Yes Yes No
A00 Yes No Yes
800 Yes No No
600 No Yes Yes
400 No Yes No
100 No No Yes
000 No No No
Address
+208@@@@
Value (Hex) Minimum cycle time

0000 Cycle time not fixed
0001 Cycle time fixed: 1 ms
to
7D00 Cycle time fixed: 32,000 ms
Address
+209@@@@
Value (Hex) Watch cycle time

0000 Default: 1,000 ms (1 s)
0001 10 ms
to
0FA0 40,000 ms
Address
+218@@@@
Value (Hex) Fixed peripheral servicing time

0000 Default (4% of the cycle time)
8000 00 ms
8001 0.1 ms
to to
80FF 25.5 ms
150
Address
219@@@@
Time Slice Perpheral Servicing Time

Value (Hex) Setting
00 Do not use Peripheral Servicing Priority Mode
01 to FF Time Slice Peripheral Servicing Time
(0.1 to 25.5 ms in 0.1-ms increments)
Time Slice Instruction Execution Time
Value (Hex) Setting
00 Do not use Peripheral Servicing Priority Mode
05 to FF Time Slice Instruction Execution Time
(5 to 255 ms in 1-ms increments)
Address
220@@@@
Special Peripheral Servicing Unit Numbers

Value (Hex) Setting
00 No special servicing
10 to 1F CPU Bus Units 0 to 15 (unit number + 10 Hex)
20 to 7F Special I/O Units 0 to 95 (unit number + 20 Hex)
E1 Inner Board
FC RS-232C port
FD Peripheral port
Value (Hex) Setting

E1 Inner Board
FC RS-232C port
FD Peripheral port
Address
221@@@@

Value (Hex) Setting
E1 Inner Board
FC RS-232C port
FD Peripheral port
Value (Hex) Setting

E1 Inner Board
FC RS-232C port
FD Peripheral port
151
Address
222@@@@
Not used.
Value (Hex) Setting
E1 Inner Board
FC RS-232C port
FD Peripheral port
Address
+225@@@@
Power-OFF Power-OFF detection

Value (Hex) interrupt task delay time
0000 Disabled 0 ms
0001 1 ms
to to
000A 10 ms
8000 0 ms
Enabled
8001 1 ms
to to
800A 10 ms
Address
+226@@@@
Special I/O Unit cyclic refreshing 0: Yes 1: No

Value (Hex) Unit number
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
0000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0001 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1
0002 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0
0003 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1
0004 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0
0005 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 1
to
FFFF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Note Address +227 through to +231 are the same as +226
152
Index
$±% fatal operating errors, 115

non fatal operating errors, 116
All Clear, 38 reading/clearing, 114
ASCII coding sheet, 141 errors
AUTOEXEC verification errors, 49
precautions, 125
bit address change, 71
bit addresses
)
for inputting basic instructions, 54 force set/reset
bit search, 67 clear, 101
using bit addresses, 68 continuous, 99
buzzer operation, 42 temporary, 100
buzzer volume, 9 functions

All Clear, 5
buzzer operation, 5, 42
& cycle time read, 5
I/O Table Create, 45
clock I/O Table Verify, 48
read/change, 112 instruction variation change, 5
connection, 14, 19 Memory Clear, 5
panel mounting, 15 monitoring, 6
CX-Programmer, 3 Program Edit, 5
cyclic tasks, 44 Program Read, 5
Program Write, 5
Programming Console, 5
' reading/clearing error messages, 5
selecting tasks, 5, 43
DIP switch special functions, 6
settings, 18 Table Create, 5
display Table Verify, 5
double-word, 95, 97 Timer/Counter SV change, 5
hexadecimal or BCD, 93 unsupported, 7
signed decimal, 95
unsigned decimal, 96
display contrast, 9 ,±-
display format, 88 I/O bit status monitor, 78
I/O Table Create, 45
( I/O table operations, 45

I/O Table Verify, 48
editing, 69
index register addresses
bit address change, 71
for inputting basic instructions, 55
instruction change, 69
initial display, 32, 33
instruction delete, 71
instruction insert, 70 inputting instructions
instruction variation change, 73 basic instructions, 53
N.O./N.C. change, 72 special instructions, 60
online, 102 standard special instructions, 60
Timer/Counter SV changes, 74 symbol comparison instructions, 61
Timer/Counter, 57
error messages, 143, 145
installation, 1
153
Index
instruction change, 69 ASCII monitor, 92

instruction delete, 71 bit addresses, 80
instruction insert, 70 clearing displays, 87
designated words, 82
instruction search, 66
differential monitor, 101
instruction variation
display format, 88
change, 73
I/O multipoint monitor, 85
instruction variations, 57 I/O multipoint monitor results, 86
interrupt tasks, 45 operands at specified program addresses, 84
Japanese messages signed decimal monitor, 90
change to English, 18 simple I/O monitor, 79
specified bits, 79
Timer/Counter completion flags, 81
.±/ unsigned decimal monitor, 91
word addresses, 83
key input modes, 36
word monitor, 89
Normal Input, 36
MSG(046), 117
Shift Input, 36
Text Input, 36
keys
functions, 11, 36
1±2
keypad layout, 37 N.O./N.C. change, 72
layout, 13 online editing, 102
names, 11 bit address change, 106
ladder programming, 5 instruction add, 103
instruction change, 102
instruction delete, 105
0 instruction insert, 104
instruction variation change, 108
maintenance, 111
N.O./N.C. change, 107
cycle time read, 113
Timer/Counter SV change, 109
memory areas
operation
All Clear, 37, 38
changing operating modes, 35
clearing memory, 37
initial display, 32, 33
Memory Clear, 37, 41
starting, 32
specifying areas, 38
memory cards
file delete, 133 3
file memory operations, 120
file read, 126 panel mounting, 15
file verify, 130 password, 32, 33
file write, 122 PC setup
formatting, 121 procedure, 138
memory types, 120 setting sheet, 145
operations, 119 precautions
Memory Clear, 41 general, xi
mode switch, 9, 35 handling, 7
operating modes, 10 operating environment, 7
models previous models
C200H and CQM1, 2 comparison with, 16
monitoring programming, 18
154
Index
checking program operation, 26 word PVs

inputting basic instructions, 53 changing, 92
inputting instructions, 52
inputting programs, 22
one cyclic task, 3
writing and editing programs, 51
Programming Console
connection, 19
features, 3
functions, 5
operation, 31
setup, 17
programs
bit search, 67
checking and adjusting, 77
editing, 69
instruction search, 66
reading and searching, 65
reading designated addresses, 65
reading execution status, 78
PVs
changing from signed decimal monitor, 94
changing from the ASCII monitor, 97
changing from the word monitor, 98
changing from unsigned decimal monitor, 96
6
selecting tasks, 43
simple I/O monitor, 79
standard special instructions
inputting, 60
symbol comparison instructions, 61
bit addresses, 62
constants, 64
indirect DM addresses, 63
indirect EM addresses, 63
instruction variations, 64
7±:
tasks
cyclic tasks, 43
interrupt tasks, 44
Timer/Counter set values, 58
change, 74
constants, 58
indirect DM addresses, 59
indirect EM addresses, 59
words, 58
155
Revision History
A manual revision code appears as a suffix to the catalog number on the front cover of the manual.
Cat. No. W341-E-03
Revision code
The following table outlines the changes made to the manual during each revision. Page numbers refer to the
previous version.
Revision code Date Revised content
01 March 1999 Original production
02 May 2001 Information on CJ-series PCs, the CQM1H-PRO01-E Programming Console,
and PC Setup addresses 219 to 222 added.
03 September 2001 Information on new CPU Units.
Page ix: Addition to introduction at top of page and model numbers added to
manual names.
Page 2: Model numbers added to bottom table and information added after
table.
Pages 9, 15, 18, 20, 32 to 36, and 42: “CS Series” changed to “CS1” and “CJ
Series” changed to “CJ1/CJ1-H/CS1-H.”
Page 46: Note added toward top of page and section and note added to bottom.
Pages 138 to 145: Deleted.
Pages 148 to 154: Moved to Appendix C.
Pages 148, 150, and 151: Note added.
Pages 149 and 152: Information for new addresses added.
Page 151: Information for following addresses moved to correct order: 163, 166.
157
OMRON ELECTRONICS LLC
1 Commerce Drive
Schaumburg, IL 60173 USA
800.55.OMRON (66766)
OMRON CANADA, INC.

885 Milner Avenue
Scarborough, Ontario M1B 5V8
416.286.6465
OMRON ON-LINE
Global - http://www.omron.com
USA - http://www.omron.com/oei
Canada - http://www.omron.com/oci
800.55.OMRON or 847.843.7900
Sao Paulo 55.11.5564.6488
Buenos Aires 54.114.787.1129
Florida 954.227.2121
W341-E1-3 02/02 Printed in U.S.A. ©2001 OMRON ELECTRONICS LLC Specifications subject to change without notice.

Prog Consoles CQM1H-PRO01

Uploaded by

Copyright:

Available Formats

Prog Consoles CQM1H-PRO01

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Prog Consoles CQM1H-PRO01

Uploaded by

Copyright:

Available Formats

Cat. No.

SYSMAC CS/CJ Series

OMRON Product References

1 Intended Audience . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xii

• Transferring I/O memory data from other personal computers or host

4 Operating Environment Precautions

• Locations subject to direct sunlight.

!Caution Take appropriate and sufficient countermeasures when installing systems in

• Locations subject to static electricity or other forms of noise.

• Fail-safe measures must be taken by the customer to ensure safety in the

1-1 Applicable Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

1-1 Applicable Models

The Programming Console is connected to the peripheral port on the CPU

Applicable CPU Units

Note CS1 CPU Units: CS1H-CPU6@-EV1 and CS1G-CPU4@-EV1

1-2 Using the Programming Console

Programming Console Programming is started by using the CX-Programmer, a programming and

Checking the program

Creating I/O tables First rack words cannot be set.

Debugging Modifying the program

Changing the set values

Monitoring Making changes to

1-3 Programming Console Functions

Buzzer Operation. See p42.

Specifying memory areas not to clear. See p38.

Specifying the first program address to clear. See p41.

Creating/Verifying I/O Tables

I/O Table Create. See p45.

Reading/Clearing Error Messages. See p114.

Selecting Tasks See p43.

Program Read Setting Addresses See p65.

Program Write Instruction Write

Program Edit Instruction Change See p69.

Instruction Variation Change See p73.

Timer/Counter SV change See p74.

Timer/Counter SV Change 1 (Sets constant or word)

Simple I/O Monitor See p79.

I/O Multipoint Monitor See p85.

Differential Monitor See p101.

Online Editing See p96.

Program Edit Instruction Change See p102.

Instruction Variation Change See p108.

Timer/Counter SV Change See p109.

Timer/counter SV Change 1 (Sets constant or word)

Clock Read/Change See p112.

Data transfer from PC to Memory Card See p121.

1-4 Unsupported Functions

1-5 Functions and Nomenclature

Cassette connector jack

f: Key can be removed

Contrast adjustment knob

Buzzer volume minimum

Buzzer volume maximum

1-5-2 The Mode Switch and Operating Modes

MONITOR MONITOR The CPU Unit is operating and I/O processing

1-5-3 Key Functions

Text input Text input Text input

• Press the SHIFT Key first to use the shift input.

NOT Key NOT --- C

SHIFT Key Alters the function of --- F