Alaris Medley Pump Module 8100 Version 4b

MEDLEY™
MEDICATION SAFETY SYSTEM

INFUSION PUMP MODULE
Model 8100
INFUSING
ALARM STANDBY
INFUSION PUMP MODULE

CHANNEL
MODEL 8100
SELECT
PUMP
PAUSE
CHANNEL
OFF
RESTART
DIRECTIONS FOR USE
TABLE OF CONTENTS
INTRODUCTION
ABOUT THE SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
INTRODUCTION
FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
SYMBOLS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
GETTING STARTED
WARNINGS AND CAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
CONTROLS AND INDICATORS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
INSTALLATION PROCEDURE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
ATTACHING AND DETACHING CHANNELS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
START-UP SEQUENCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
GETTING STARTED
PREPARING INFUSION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
DISPLAYS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
PRIMARY MODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
SECONDARY MODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
CHANNEL LABELS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
POWERING OFF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
CHANGING PRIMARY SOLUTION CONTAINER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
CHANGING AND RELOADING SET DURING INFUSION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
DRUG CALCULATION PARAMETERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
ALARMS, ADVISORIES
SETTING UP DRUG CALCULATION WITH DRUG LIBRARY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
AND PROMPTS
SETTING UP DRUG CALCULATION FOR NON-LIBRARY DRUGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
SETTING BOLUS DOSE (DRUG CALCULATION WITH DRUG LIBRARY) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
SETTING BOLUS DOSE (DRUG CALCULATION FOR NON-LIBRARY DRUGS) . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
ANESTHESIA MODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
REVIEWING SERIAL NUMBER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
REVIEWING SOFTWARE VERSION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
ALARMS, ADVISORIES AND PROMPTS
DEFINITIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
AUDIO CHARACTERISTICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
MAINTENANCE
ALARMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
ADVISORIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
ERRORS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
MAINTENANCE
SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
CONFIGURABLE SETTINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
CHECK-IN AND CONFIGURATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
CLEANING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
INSPECTION REQUIREMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
SERVICE INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
APPENDIX
WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
APPENDIX
TRUMPET AND START-UP CURVES ......................................................................... 57
GENERAL CONTACT INFORMATION
Customer Advocacy
For clinical and technical questions, feedback, and troubleshooting assistance.
Phone, toll-free, within the United States and Canada: (800) 854-7128, Ext. 7812
E-Mail: CustomerFeedback@alarismed.com
Technical Support
For technical information related to maintenance procedures and service manual support.
Phone:
(858) 458-6003
Toll-free, within the United States: (800) 854-7128, Ext. 6003
Toll-free, within Canada:
Eastern: (800) 227-7215
Western: (800) 667-2335
For more detailed information, refer to the “Service Information” section of this document.
INTRODUCTION
About the System
The MEDLEY™ Medication Safety System is a modular infusion
INTRODUCTION
and monitoring system intended for use in today’s growing
professional healthcare environment, including healthcare
facilities and home care, for use on adults, pediatrics and
neonates.
The MEDLEY™ Pump Module is intended for facilities that utilize

infusion pumps for the delivery of fluids, medications, blood and
blood products using continuous or intermittent delivery
through clinically acceptable routes of administration; such as,
intravenous (IV), intra-arterial (IA), subcutaneous, epidural,
enteral, or irrigation of fluid spaces.
The MEDLEY™ Medication Safety System consists of the

Programming Module (Model 8000), the Guardrails® Safety
Software, and detachable modules (or “channels”), which
provide infusion or monitoring capabilities.
This document provides directions for use for the Model 8100
Infusion Pump Module. Please read all instructions, for both the
Pump Module and Programming Module, before using the
device.
The MEDLEY™ System uses a wide variety of ALARIS® MEDLEY™/

Gemini Administration Sets. The sets are designed for use with
the Pump Module as well as for gravity-flow, stand-alone use.
For specific administration set instructions, refer to the directions
for use provided with the set. For set priming and loading
instructions, refer to the “Start-Up Sequence” section of this
document.
Contraindications: None known.
INTRODUCTION 1
Features
Anesthesia Mode The Anesthesia Mode allows the anesthesiologist to access additional
drugs in each profile that are appropriate to anesthesiology. This mode
also features permanent pause and the ability to set higher air-in-line
settings.
AutoRestart The AutoRestart feature is part of the MEDLEY™ System’s advanced

Downstream Occlusion Detection system. If enabled, the AutoRestart
feature minimizes nuisance patient side occlusion alarms caused by
momentary kinking of tubing, IV pushes, etc.
Bolus Dose The Bolus Dose mode enables the clinician to program a bolus infusion.
It is possible to program a bolus using the Guardrails® Drug Library or
using the Drug Calculation feature. The bolus infusion can be
programmed with or without a continuous infusion following the bolus.
Channel Labels The Channel Label feature is available if the Profiles feature is enabled. It
provides a hospital-defined list of labels which can be displayed in the
Channel Message Display, allowing the user to identify the channel with
the solution being infused, the catheter location or other helpful
information.
Drug Calculation The Drug Calculation mode allows the user to:
enter the desired drug dose and the MEDLEY™ System calculates the
correct flow rate to achieve the desired dose,
OR
enter the desired flow rate and the MEDLEY™ System calculates the
corresponding drug dose.
Dynamic Pressure Display The Dynamic Pressure Display is located just below the Channel Status
information in the Main Display of the Programming Module. If
enabled, it graphically displays the current patient side occlusion pressure
set point and the current patient side operating pressure for that
channel.
Flow Rates The flow rate range is from 0.1 to 999 mL/h. Rates between 0.1 and 99.9
may be selected in 0.1 mL/h increments. Rates from 100 to 999 mL/h are
selected in 1 mL/h increments.
Free Flow Protection All MEDLEY™/Gemini Disposable Sets utilize a unique clamping device,
the Flo–Stop® Device, to prevent inadvertent free flow when the set is
removed from the instrument.
Guardrails® Drug Library The Guardrails® Drug Library feature is a Drug Calculation mode available
when the Profiles feature is enabled. It provides a hospital-defined list of
up to 100 drugs and concentrations appropriate for use in the selected
profile. Using the Drug Library automates programming steps, including
the drug name, drug amount and diluent volume, and activates the
hospital-established best-practice Guardrails® Limit.
2 INTRODUCTION
Features (Continued)
Guardrails® Prompt The Guardrails® Safety Software is designed to help prevent

programming errors by:
INTRODUCTION
• Customizing device configurable settings to meet the need of the
selected hospital area/unit (profile).
• Comparing user programming with hospital-defined best-practice
guidelines.
• Providing a Guardrails® Prompt if an out-of-limits entry is made.
Occlusion Pressure The MEDLEY™ System provides a complete range of Downstream

Occlusion Detection options, including:
• Pump mode, where the downstream occlusion alarm threshold is
525 mmHg at flow rates of 30 mL/h or greater. For rates <30 mL/h,
the occlusion pressure is rate-dependent, to ensure rapid response to
occlusions.
• Selectable pressure mode, where the downstream occlusion alarm
threshold can be adjusted by the user in 25 mmHg increments, up to
the maximum occlusion pressure of 525 mmHg.
• AutoRestart (see previous page)
In addition, the MEDLEY™ System provides fluid side occlusion detection.
Profiles The Profiles feature allows a unique set of system options (profile) to be
configured to optimize system function for a specific hospital area or
patient type. A profile is comprised of a configuration, with system
settings and defaults customized by the user to best meet the needs of
the profile area/patient type.
Secondary Infusions Dual rate sequential piggyback (Secondary) infusions may be infused at
delivery rates and volumes independent of the primary infusion
parameters. Automatic changeover occurs to the primary infusion
parameters when the secondary infusion is complete if a
MEDLEY™/Gemini Check Valve Administration Set is used.
System Configuration The System Configuration mode provides the ability for qualified
personnel to customize device settings. If the Profiles feature is enabled,
the system settings defined for the selected profile are automatically
activated.
Tamper Resist The Tamper Resist feature provides a quick, one-touch lockout of the
front keypad.
Volume/Duration The Volume/Duration infusion option allows the user to program a

volume-to-be-infused (VTBI) and duration (infusion time), and the flow
rate is automatically calculated.
Volume-To-Be-Infused (VTBI) The volume-to-be-infused (VTBI) range is from 0.1 to 9999 mL. Volumes
between 0.1 and 999.9 may be selected in 0.1 mL increments. VTBIs
from 1000 to 9999 mL are selected in 1 mL increments.
INTRODUCTION 3
Symbols
Canadian and U.S. Certification Mark: Products bearing this mark have been tested and
certified in accordance with applicable U.S. and Canadian electrical safety and performance
+ 75
standards (CSA C22.2 No. 601.1, UL 2601-1 and IEC 60601–2–24).
Electrical Shock Protection Rating: Type CF, Defibrillation-proof
IPX1 Protection against fluid ingress: Drip Proof
! Attention: Refer to accompanying documentation.
IUI Connector: Inter-Unit Interface connector used to establish power and

communications between the Programming Module and add on channels.
Manufacturing Date: Number adjacent to symbol indicates the month and year of
MM-YYYY manufacture.
Consult operating instructions.
Only CAUTION: Federal (U.S.A.) law restricts this device to sale by or on the order of a physician.
Single-Use
Single-Use. Do not re-use.

2
Product contains a particular element; such as, DEHP = DEHP in fluid pathway.
Product DOES NOT contain a particular element; such as, LATEX = set is latex-free.
XX Drops per milliliter specification for product will be identified on drop symbol.
Product incorporates SmartSite® Needle-Free Valve Ports and should not be accessed by a
needle.
XX ml Approximate set priming volume.
Expiration date for product will be identified near hour glass symbol.
4 INTRODUCTION
GETTING STARTED
NOTE: Although the MEDLEY™ System is built and tested to Only

exacting specifications, it is not intended to replace the supervision
of IV infusions by medical personnel. The user should become
thoroughly familiar with the features and operation of the
MEDLEY™ System and exercise vigilance in its utilization.
Definitions
WARNING
This heading alerts the user to potential serious outcomes
(death, injury or serious adverse events) to the patient or user.
GETTING STARTED
CAUTION
This heading alerts the user to take special care for the safe and
effective use of the device.
Warnings and Cautions
For WARNINGS and CAUTIONS for the Programming Module,

refer to its Directions for Use.
To ensure proper performance of the MEDLEY™ System and to
reduce potential injury, observe the following precautions:
Epidural Administration WARNING

The MEDLEY™ System can be used for epidural administration Epidural administration of drugs
of anesthetic and analgesic drugs. This application is only other than those indicated for
appropriate when using analgesics and anesthetics labeled epidural use could result in serious
for continuous epidural administration and catheters injury to the patient.
intended specifically for epidural use. Use only a
MEDLEY™/Gemini Series set, without a ‘Y’ connector or WARNING
injection port, for epidural infusions.
It is strongly recommended that the
• Epidural administration of anesthetic drugs: Use infusion pump, source container and
indwelling catheters specifically indicated for short term MEDLEY™/Gemini Administration Set
(96 hours or less) anesthetic epidural drug delivery. used for epidural drug delivery be
• Epidural administration of analgesic drugs: Use indwelling clearly differentiated from those used
catheters specifically indicated for either short term or for other types of administration.
long term analgesic epidural drug delivery.
GETTING STARTED 5
Warnings and Cautions (Continued)
WARNING
This instrument is designed to stop fluid flow under alarm
conditions. Periodic patient monitoring must be performed to
ensure the infusion is proceeding as expected.
WARNING
This infusion device is a positive pressure delivery system,
capable of developing positive fluid pressures to overcome
widely varying resistances to flow encountered in practice,
including resistances to flow imposed by small gauge catheters,
filters and intra-arterial infusion. It is neither designed nor
intended to detect infiltrations and will not alarm under
infiltration conditions.
WARNING
Hospital personnel must ensure the compatibility of the drugs as
well as the performance of each channel as part of the overall
infusion. Potential hazards include drug interactions, inaccurate
delivery rates, inaccurate pressure alarms and nuisance alarms.
WARNING
Do not use the MEDLEY™ System during Magnetic Resonance
Imaging (MRI).
WARNING
Use only MEDLEY™/Gemini Series administration sets. The use of
any other set may cause improper instrument operation,
resulting in an inaccurate fluid delivery or other potential
hazard.
WARNING
The use of positive displacement infusion devices ported
together with gravity flow infusion systems into a common IV
site may impede the flow of common “gravity only” systems,
affecting their performance. Hospital personnel must ensure the
performance of the common IV site is satisfactory under these
circumstances.
WARNING
References in this document to specific drugs and drug doses
are for example only. Refer to specific drug product labeling for
information concerning appropriate administration techniques
and dosages.
6 GETTING STARTED
Parallel Infusions
There are no contraindications regarding the use of the
MEDLEY™ System with any other positive displacement
infusion device when ported together into a common IV site
location.
User Precautions
To ensure proper performance of the MEDLEY™ System and to

reduce potential injury to the operator, observe the following
precautions:
GETTING STARTED
• Disconnect from main (AC) and battery power when
performing maintenance.
• Do not open the instrument case. There are no user
serviceable parts inside. The case should only be opened by
qualified service personnel using proper grounding
techniques. When the case is opened, an electrical shock
hazard exists which can result in serious injury to persons and
instrument component damage.
Administration Sets WARNING

• A list of approved IV sets recommended by ALARIS Medical Use only MEDLEY™/Gemini Series
Systems for use with the MEDLEY™ Medication Safety administration sets. The use of any
System Pump Module is listed on the Set Compatibility other set may cause improper
Card. instrument operation, resulting in an
inaccurate fluid delivery or other
• Before operating the instrument, verify that the
potential hazard.
administration set is free from kinks and installed correctly
in the instrument.
• MEDLEY™/Gemini Series sets are supplied with a sterile
fluid path for one time use. Do not resterilize.
• For set replacement interval, refer to facility protocol
and/or government standards (such as, CDC guidelines in
the United States).
• For IV push medication (put instrument on hold), clamp
tubing above the port.
• Flush port(s) per facility protocol.
• Discard administration set per facility protocol.
GETTING STARTED 7
User Precautions (Continued)
Artifacts
It is normal for an infusion device to produce nonhazardous
currents when infusing electrolytes. These currents vary
proportional to the infusion device flow rate. When the ECG
monitoring system is not functioning under optimal
conditions, these currents may appear as artifacts, simulating
actual ECG readings. To determine if ECG abnormalities are
caused by patient condition or the ECG equipment, place the
infusion device on hold. If the ECG readings become normal,
the ECG equipment requires attention. Proper setup of the
ECG equipment should eliminate these artifacts. Reference
the appropriate ECG monitoring system documentation for
instructions on setup and maintenance.
Dropping/Jarring
Should an instrument be dropped or severely jarred, it should
be immediately taken out of use and inspected by qualified
service personnel, to ensure its proper function prior to reuse.
Operating Environment DANGER

Not for use in the presence of flammable anesthetics. Explosion risk if used in the presence
of flammable anesthetics.
8 GETTING STARTED
User Precautions (Continued)
Radio Frequency Interference WARNING

Operating the system near equipment which radiates high Use of accessories or cables other
energy radio frequencies (electrosurgical/cauterizing than those specified may result in
equipment, portable radios, cellular telephones, etc.) may degraded electromagnetic
cause false alarm conditions. If this happens, reposition the compatibility performance of this
device away from the source of interference or turn off the device.
device and manually regulate the flow with the clamp and/or
monitor the vital parameters using an appropriate clinical
alternative.
GETTING STARTED
GETTING STARTED 9
Controls and Indicators
Front/Side View - Door Closed
IUI Connector, Right

Status Indicators (not visible)
Alarm Infusing Standby

IUI Connector, Left (red) (green) (yellow)
Rate Display
STANDBY
Channel Message Display
INFUSE
RM
ALA
Channel Identification
Channel Select Key - When

pressed, selects corresponding
channel for infusion parameter
entry and infusion setup.
NEL
CHAN T
SELEC
Pause Key - When pressed during

PAUSE
an infusion, temporarily stops
infusion on that channel. (After
CHAN
NEL ≈2 minutes, “PRESS START” visual
OFF
and audio prompt begins.)
RT
RESTA
Channel Off Key - When pressed

and held for one second and then
released, stops infusion on that
channel, deselects that channel, and if
only that channel had been operating,
system powers down. Repeat for other
operating channels to power off each
channel.
Restart Key - When pressed, resumes

operation of a previously paused or
alarmed infusion on that channel.
Door Handle
Channel Release Latch
10 GETTING STARTED
Controls and Indicators (Continued)
Front View - Door Open
IUI Connector, Left

(not visible)
Upper Tubing
Fitment Retainer
GETTING STARTED
Platen
IUI Connector, Right
Upper Pressure Sensor
Upper Occluder
Upper Pumping Finger
Door Latch Cam/Slide Lower Occluder
Lower Pumping Finger
Lower Pressure Sensor
Flo-Stop® Recess
Tubing Keeper
Air-in-Line Sensor
GETTING STARTED 11
Installation Procedure
Instruments are tested and calibrated before they are packaged

for shipment. They met the specifications listed in the Directions
for Use at that time. To ensure proper operation after shipment,
it is recommended that an incoming inspection be performed
before placing the instrument in use.
Unpacking the Pump Module
1. Remove Pump Module from its carton.
2. Verify door operates freely.
3. Verify membrane covering inside surface of pumping unit is

not cut or torn.
4. Check for loose parts.
5. Perform Periodic Inspection (see “Inspection Requirements”

section in “Maintenance” chapter.)
6. Perform check-in procedure (see “Check-In and

Configuration” section in “Maintenance” chapter).
If the Pump Module is damaged, contact ALARIS Medical
Systems for authorization to return the equipment for repair,
whether damage or malfunction is the responsibility of the
carrier or ALARIS Medical Systems.
Attaching and Detaching Channels
Refer to the MEDLEY™ Programming Module (Model 8000)

Directions for Use for detailed instructions on attaching and
detaching channels.
Start-Up Sequence
Powering On the System
1. Connect MEDLEY™ Programming Module to an external AC

power source.
2. Press SYSTEM ON key on Programming Module.
3. System self test begins:

• Diagnostics test causes all LED display segments and
Status Indicator lights of attached channel(s) to
illuminate briefly.
• Power Indicator illuminates.
12 GETTING STARTED
Start-Up Sequence (Continued)
Powering On the System (Continued)
• Appropriate channel identification (A, B, C or D) is

displayed on attached channel(s).
• An Audio tone sounds.
4. At completion of system-on test, “New Patient?” screen
appears on Programming Module.
NOTE: If any of the following conditions are observed, the

Programming Module or the affected channel must be removed
from use and inspected by qualified personnel:
GETTING STARTED
• LED segments are not illuminated during system-on test.
• Indicator lights do not illuminate.
• Appropriate channel identification (A, B, C or D) is not
displayed.
• Audio tone does not sound.
• Main Display does not appear backlit, appears irregular, or has
evidence of a row of pixels not functioning properly.
If the affected channel operates normally when it is attached via the
alternate IUI connector, it may be used until a replacement channel
can be substituted.
Preparing Infusion
Preparing Primary Solution Container
Prepare the primary solution container in accordance with the

manufacturer’s directions for use.
Preparing Primary Administration Set
Use only a MEDLEY™/Gemini Series administration set (refer to

Set Compatibility Card for a list of compatible sets). Open the
administration set package, remove the set and close the roller
clamp. Refer to the set’s Directions For Use, on the
administration set packaging.
Loading Primary Administration Set
1. Insert set spike into prepared fluid container, following

accepted hospital procedure, and hang container 20 inches
above Pump Module.
2. Fill drip chamber to 2/3 full.
3. Open roller clamp slowly, to prime tubing and clear air from
injection sites and tubing fitments.
GETTING STARTED 13
Preparing Infusion (Continued)
Loading Primary Administration Set (Continued)
4. Close roller clamp.
5. Open Pump Module door. Install administration set

pumping chamber by properly positioning upper fitment
into fitment recess and then inserting the Flo–Stop® Fitment
into recess below mechanism, with arrow pointing into
Pump Module.
6. Using a finger tip, firmly push tubing toward back of Air-in-

Line Detector.
7. Close Pump Module door and open roller clamp. Verify no

fluid is flowing through drip chamber.
1. Load upper tubing fitment.
2. Load Flo-Stop® Fitment.
3. Firmly push tubing toward back of

Air-in-Line Detector.
Preparing Set to Deliver Primary Fluids with Gravity Infusion
1. Prime set per steps 1 - 4 in “Loading Primary Administration

Set” section.
2. Attach set to patient’s vascular access device.
3. Adjust flow rate with set roller clamp.
14 GETTING STARTED
Displays
Main Display

Directions for Use for general information in the Main Display.
Title Bar
Channel Status VTBI = 250.0 mL
• A solid Channel Letter display
indicates channel is operating.
• An outlined Channel Letter display
indicates channel is attached and
GETTING STARTED
SYSTEM
ON
ready for use.
Soft Keys
VOLUME AUDIO
INFUSED ADJUST
Dynamic Pressure Display
Midtown Hospital
Adult ICU
VTBI = 250.0 mL
Dynamic Pressure Display

Current operating pressure is
indicated by solid bar. SYSTEM
ON
Patient side occlusion pressure set

point is indicated by tick mark.
VOLUME AUDIO
INFUSED ADJUST
Primary Mode
Primary - Rate/Volume Infusion
NOTE: Throughout this section, the Main Display screens are

aligned so that they coincide with the applicable step. Infusion Setup
RATE mL/h
1. Prime and load administration set as described in VTBI mL
“Preparing Infusion” section.
2. Press CHANNEL SELECT key on desired Pump Module.
>Select RATE
GETTING STARTED 15
Primary Mode (Continued)
Primary - Rate/Volume Infusion
3. Press RATE soft key and use numeric data entry keys to enter Infusion Setup
desired flow rate. RATE 40 mL/h
VTBI mL
>Select VTBI
4. Press VTBI soft key and use numeric data entry keys to enter Infusion Setup
desired VTBI. RATE 40 mL/h
VTBI 250 mL
>Press START
SECOND-
PAUSE START
ARY
6. Verify correct infusion parameter entry and press START soft Midtown Hospital
Adult ICU
key on Programming Module. VTBI = 250.0 mL
NOTE: The infusion may also be paused by pressing the

PAUSE soft key on the Programming Module.
• Green Infusing Status Indicator illuminates.

• Channel Rate Display displays Rate.
• VTBI counts down in Main Display. VOLUME
INFUSED
AUDIO
ADJUST
• At completion of infusion, an audio prompt sounds,

“INFUSION COMPLETE–KVO” scrolls in Channel Message
Display and red Alarm Status Indicator flashes. Rate
Display changes to KVO rate and KVO displays next to
channel indicator in Main Display.
Primary - Volume/Duration Infusion
1. Prime and load administration set.

Infusion Setup
2. Press CHANNEL SELECT key on desired Pump Module. RATE _ _ _ mL/h
VTBI _ _ _ _ mL
>Select Rate or Restore

Previous Infusion
VOLUME
RESTORE DURATION
16 GETTING STARTED
Primary - Volume/Duration Infusion (Continued)
3. Press VOLUME/DURATION soft key. Infusion Setup

RATE = mL/h
VTBI _ _ _ _ mL
DURATION h min
>Select VTBI
RESTORE RATE
VOLUME
GETTING STARTED
4. Press VTBI soft key and use numeric data entry keys to enter Infusion Setup
desired VTBI. RATE = mL/h
VTBI 1000 mL
DURATION h min
>Select DURATION
RATE
VOLUME
5. Press DURATION soft key and use numeric data entry keys to Infusion Setup
enter desired duration of the infusion. RATE = 125 mL/h
VTBI 1000 mL
DURATION 8:00 hh:mm
>Press START
RATE SECOND-
START
PAUSE VOLUME ARY
7. Verify correct infusion parameter entry and press START soft

key.
• Green Infusing Status Indicator illuminates.
• Channel Rate Display displays Rate.
• VTBI counts down in Main Display.
• At completion of infusion:
a. An audio prompt sounds.
b. “INFUSION COMPLETE–KVO” scrolls in Channel Message
Display.
c. Red Alarm Status Indicator flashes.
d. Rate Display changes to KVO rate.
e. KVO displays next to channel indicator in Main Display.
f. Channel infuses at KVO rate.
GETTING STARTED 17
Pausing an Infusion
1. Press PAUSE key on Pump Module. Midtown Hospital

Adult ICU
PAUSED
• “PAUSE” scrolls in Channel Message Display. VTBI = 497.0 mL
• “PAUSED” appears next to appropriate channel in Main VTBI = 57.0 mL
Display. VTBI = 249.0 mL
• Yellow Standby Status Indicator illuminates.

• After two minutes, “PAUSE-RESTART CHANNEL” visual and
audio prompts begin. VOLUME
INFUSED
AUDIO
ADJUST
2. To reinitiate an infusion:
• Press RESTART key on Pump Module.
OR
• Press CHANNEL SELECT key and press START soft key.
Restarting an Infusion Following Infusion Complete - KVO
1. Press CHANNEL SELECT key on Pump Module. Infusion Setup

RATE 40 mL/h
VTBI 0 mL
>Select VTBI
VOLUME
RESTORE
DURATION
2. Press VTBI soft key on Programming Module and use Infusion Setup
numeric data entry keys to enter desired VTBI, or press RATE 40 mL/h
RESTORE soft key to bring back original volume-to-be- VTBI 500 mL
infused from system memory.
3. Replace solution container and refill drip chamber, if

necessary.
>Press START
4. Verify correct infusion parameter entry and press START soft PAUSE VOLUME SECOND-
START
key.
DURATION ARY
18 GETTING STARTED
Changing Rate or VTBI During an Infusion

RATE 40 mL/h
2. Press either RATE or VTBI soft key on Programming Module. VTBI 240 mL
>Press START
PAUSE SECOND-
ARY START
GETTING STARTED
3. Use numeric data entry keys, or Up and Down keys for Rate Infusion Setup
titration, to enter desired parameter. RATE _50 mL/h
VTBI 240 mL
4. Verify correct infusion parameter entry and press START soft
key.
>Press START
PAUSE SECOND-
ARY START
Stopping an Infusion on a Channel
Press and hold CHANNEL OFF key on Pump Module for one
second.
NOTE: The channel will initiate the power down at the release of
the CHANNEL OFF key.
Selecting Pressure Mode - Pump (P) / Selectable (S)
1. Press CHANNEL SELECT key on Pump Module. Channel Options 1 of 1

Drug Calculation Setup
2. Press OPTIONS key on Programming Module. Pressure Limit - P
Channel Labels
>Select an Option or
EXIT
EXIT
GETTING STARTED 19
Selecting Pressure Mode - Pump (P) / Selectable (S)

(Continued)
3. Press Pressure Limits soft key.

Pressure Limit Selection
4. Press either Pump or Selectable pressure soft key. If Pump
Selectable is pressed, continue with next step; otherwise, Selectable
proceed to step 7.
EXIT
EXIT
5. Use either Up or Down soft key to select desired occlusion

pressure limit. Pressure Limit Selection
Selectable Pressure
6. Verify correct occlusion pressure limit input and press 525 mmHg Up
Confirm soft key. Down
7. Press START soft key.
CONFIRM
Viewing and Clearing Volume Infused for ALL Channels
1. Press VOLUME INFUSED soft key on Programming Module. Volume Infused

LAST
TOTAL VOLUME (mL)
• Total Volume Infused (Primary + Secondary), and time
CLEARED
08:00
401.1
and date Volume Infused was last cleared, is displayed
2002-03-10
07:30
42.5
for each infusion channel.
2002-03-11
08:00
478.1 2002-03-10
12:00
NOTE: Date format is year-month-day. 789.1 2002-03-10
• If no key is pressed, main screen appears after >Select Channels to Clear

or Press CLEAR ALL
30 seconds. PRI/SEC
VOLUME
CLEAR
ALL
MAIN
SCREEN
• To view Primary and Secondary volume(s) infused, press Volume Infused

PRI/SEC VOLUME soft key. PRI (mL) SEC (mL)
401.1 0.0
42.5 0.0
428.1 50.0
739.1 50.0
>Select Channels to Clear
or Press CLEAR ALL
TOTAL CLEAR MAIN
VOLUME ALL SCREEN
20 GETTING STARTED
Viewing and Clearing Volume Infused for ALL Channels

(Continued)
2. Press CLEAR ALL soft key. Volume Infused

PRI (mL) SEC (mL)
• If no key is pressed, main screen appears after
0.0 0.0
30 seconds.
0.0 0.0
• Press MAIN SCREEN soft key to return to main screen. 0.0 0.0
0.0 0.0
or Press CLEAR ALL
TOTAL CLEAR MAIN
GETTING STARTED
VOLUME ALL SCREEN
Viewing and Clearing Volume Infused for Individual

Channels
1. Press VOLUME INFUSED soft key. Volume Infused

LAST
TOTAL VOLUME (mL)
• Total Volume infused (Primary + Secondary), and time
CLEARED
08:00
401.1
and date Volume Infused was last cleared, is displayed
2002-03-10
07:30
42.5
for each infusion channel.
2002-03-11
08:00
478.1 2002-03-10
• If no key is pressed, main screen appears after 789.1 12:00

2002-03-10
30 seconds.
• To view Primary and Secondary volume(s) infused, press or Press CLEAR ALL
PRI/SEC CLEAR MAIN
PRI/SEC VOLUME soft key. VOLUME ALL SCREEN
2. Press soft key(s) corresponding to channel where volume Volume Infused

infused is to be cleared. TOTAL VOLUME (mL) LAST
CLEARED
08:00
401.1 2002-03-10
07:30
42.5 2002-03-11
08:00
478.1 2002-03-10
12:00
789.1 2002-03-10
>Press CLEAR CHANNEL

to Clear Selected
PRI/SEC CLEAR MAIN
VOLUME CHANNEL SCREEN
3. Press CLEAR CHANNEL soft key. Volume Infused

LAST
TOTAL VOLUME (mL)
• Selected channel(s) volume is cleared. CLEARED
08:00
401.1 2002-03-10
• After 30 seconds, main screen appears. 0.0 07:30

2002-03-11
08:00
478.1
4. Press MAIN SCREEN soft key to return to main screen.
2002-03-10
12:00
789.1 2002-03-10

or Press CLEAR ALL
PRI/SEC CLEAR MAIN
VOLUME ALL SCREEN
GETTING STARTED 21
AutoRestart
The AutoRestart feature is part of the MEDLEY™ System’s

Downstream Occlusion Detection system designed to minimize
nuisance, patient side occlusion alarms. It allows the system to
automatically continue an infusion following detection of a
patient side occlusion if downstream pressure falls to an
acceptable level within a 15 second “Checking Line” period.
If this feature is enabled, the “Checking Line” function will occur

when downstream pressure exceeds the Pressure Limit.
• In Selectable Pressure Mode, the Pressure Limit will be either
user adjustable or “locked” in system configuration.
• In Pump Pressure Mode, the Pressure Limit is a function of
flow rate and is automatically determined by the device.
If the downstream pressure decreases to a predetermined level,

(below 50% of the Pressure Limit) during the 15 second
“Checking Line” period, the infusion automatically continues.
If the condition is not cleared within 15 seconds, a “Partial

Occlusion - Patient Side” alarm occurs.
Qualified Service personnel can configure the system to allow

from zero (0) to nine (9) restart attempts within a rolling
10 minute period. If the allowable number of restarts is
exceeded or if the feature is set to zero, an “Occluded - Patient
Side” alarm will occur when the system detects downstream
pressure over the Pressure Limit.
22 GETTING STARTED
Secondary Mode
This mode is designed to support automatic secondary infusions WARNINGS

(“piggybacking”) in the same instrument channel. When the • Secondary applications require the
secondary VTBI reaches zero, a audio tone will sound indicating use of a check valve set on the
completion of the secondary infusion. The primary infusion primary IV line.
resumes automatically.
• The secondary solution container
When the instrument is programmed and delivering in the must be higher than the primary
secondary mode, the primary infusion is temporarily stopped solution container.
and fluid is drawn from the secondary container. Delivery from • The secondary VTBI settings
the primary container resumes when the fluid level in the require consideration of such
secondary line is level with the fluid in the primary container. variables as factory overfill,
medication additions, etc.
GETTING STARTED
NOTE: Prepare the secondary container and set. Lower the
primary container using the hanger included with the secondary
Underestimating the volume will
set. If a flow sensor is being used, it must be placed on the cause the remaining secondary
primary line. solution to be infused at the
primary rate; overestimating will
result in the primary solution
being infused at the secondary
rate. Multiple doses from a single
container are not possible.
• The clamp on the secondary set
must be opened. If the clamp is
not opened, the fluid will be
delivered from the primary
container.
• The secondary set must be primed
prior to beginning the secondary
infusion.
1. Set up and start primary infusion as previously described,

using a check valve administration set.
2. Open secondary administration set package, remove set

and close clamp.
3. Insert set spike into prepared fluid container and hang

secondary container, following accepted hospital procedure.
4. Fill drip chamber to 2/3 full.
5. Open secondary set and prime set. Close clamp.
6. Attach secondary set to upper injection site on primary set.
GETTING STARTED 23
Secondary Mode (Continued)
7. Lower primary fluid container using hanger provided with

secondary set.
NOTE: The secondary container should be at least 9½ inches

above the top of the fluid level in the primary container.

RATE 40 mL/h
VTBI 240 mL
>Press START
SECOND-
PAUSE ARY
START
9. Press SECONDARY soft key. Infusion Setup

SECONDARY
RESTORE soft key may be pressed to bring back previous
RATE
secondary infusion parameters from memory (if available). mL/h
VTBI mL
>Select Rate or Restore

Previous Infusion
RESTORE
10. Press RATE soft key. Infusion Setup

SECONDARY
11. Enter secondary infusion rate. RATE 100 mL/h
VTBI mL
>Select VTBI
12. Press VTBI soft key. Infusion Setup

SECONDARY
13. Enter secondary volume-to-be-infused. RATE 100 mL/h
VTBI 55 mL
14. Open clamp on secondary set.
>Press START
PAUSE PRIMARY START
24 GETTING STARTED
15. Verify correct infusion parameter input and press START soft Midtown Hospital
Adult ICU
key. SEC VTBI = 55.0 mL

VTBI = 497.0 mL
• Green Infusing Status Indicator illuminates. VTBI = 57.0 mL
• Channel Rate Display displays secondary rate. VTBI = 249.0 mL
• Secondary VTBI counts down in Main Display.

• “SECONDARY” scrolls in Channel Message Display.
• Upon completion of secondary infusion, switchover alert VOLUME
INFUSED
AUDIO
ADJUST
sounds with six beeps (unless disabled in system

configuration), primary rate displays and infusion
continues at primary rate.
GETTING STARTED
Changing Primary Infusion Parameter During Secondary
Infusion

SECONDARY
RATE 100 mL/h
VTBI 55 mL
>Press START
PAUSE PRIMARY START
2. Press PRIMARY soft key on Programming Module. Infusion Setup

PRIMARY
RATE 40 mL/h
VTBI 240 mL
>Press START
SECOND-
PAUSE ARY START
3. Press RATE soft key. Infusion Setup

PRIMARY
4. Use numeric data entry keys to enter desired primary Flow RATE 50 mL/h
Rate. VTBI 240 mL
>Press START
SECOND-
PAUSE ARY START
GETTING STARTED 25
Changing Primary Infusion Parameter During Secondary

Infusion (Continued)
5. Verify correct primary infusion parameter input and press Infusion Setup
SECONDARY soft key to return to secondary setup screen. SECONDARY
RATE 100 mL/h
6. Press START soft key. VTBI 55 mL
>Press START
PAUSE PRIMARY START
Stopping Secondary Infusion and Returning to Primary

Infusion

SECONDARY
RATE 100 mL/h
VTBI 43.4 mL
>Press START
PAUSE PRIMARY START
2. Press PRIMARY soft key on Programming Module. Infusion Setup

PRIMARY
3. Close clamp on secondary administration set or disconnect RATE 50 mL/h
secondary administration set from upper injection port. VTBI 240 mL
>Press START
PAUSE SECOND- START

ARY
4. Press START soft key. Infusion Setup

PRIMARY
5. Press Yes soft key selection to stop secondary infusion and RATE 50 mL/h
begin infusing primary. VTBI 240 mL
• Secondary infusion stops and primary infusion begins. Stop Secondary and
Infuse Primary?
Yes
No
• Main screen appears.
>Select Yes or No
NOTE: The SEC to PRI alert does NOT sound when the
infusion is manually ended and returned to primary.
26 GETTING STARTED
Channel Labels
Selecting Channel Label
1. Press CHANNEL SELECT key on desired Pump Module. A Channel Options 1 of 1

Channel Labels
3. Press Channel Labels soft key.
EXIT
EXIT
GETTING STARTED
4. Press soft key for desired label. A Channel
Adult ICU
Label Display
• Selected label will scroll in Channel Message Display.

0.9% NaCl A-E
3% NaCl F-J
• Use alpha–index speed select and BACK soft keys, and/or CVVHDF Dialysate K-O
PAGE UP and PAGE DOWN soft keys, to view available D5 1/2 NS P-T
labels. Epidural U-Z
>Select Channel Label
PAGE
EXIT
DOWN
A Channel Label Display

Adult ICU
Peripherial Art Line P
Replacement Solution Q
Swan R
Triple Lumen S
T
PAGE PAGE
UP BACK DOWN
5. Press START soft key or program infusion as previously

described.
GETTING STARTED 27
Channel Labels (Continued)
Removing Channel Label
1. Press CHANNEL SELECT key on desired Pump Module. A Channel Options 1 of 1

Channel Labels
3. Press Channel Labels soft key.
EXIT
EXIT
4. Press CLEAR LABEL soft key. Labels stop scrolling. A Channel

Adult ICU
Label Display
0.9% NaCl A-E
3% NaCl F-J
CVVHDF Dialysate K-O
D5 1/2 NS P-T
Epidural U-Z
CLEAR PAGE
EXIT
LABEL DOWN
5. Press START soft key. A Infusion Setup

RATE 50 mL/h
VTBI 240 mL
>Press START
VOLUME SECOND- START

PAUSE DURATION ARY
28 GETTING STARTED
Powering Off
Powering Off a Channel
1. Press and hold CHANNEL OFF key on channel(s) for one

second.
Powering Down
NOTE: The channel will initiate the power down at the
release of the CHANNEL OFF key.
2. Once all attached channels are powered off, Programming

Module automatically powers down.
During power off sequence, Main Display flashes “Powering
Down”.
GETTING STARTED
Powering Off the System
Directions for Use for instructions on Powering Off the System.
Changing Primary Solution Container

1. Press PAUSE key on desired Pump Module to stop infusion.
3. Remove empty solution container.
4. Spike new container.
6. Press VTBI soft key and use numeric data entry keys to enter
desired VTBI.
7. Open roller clamp.
Changing and Reloading Set During Infusion

1. Press PAUSE key on desired Pump Module to stop infusion.
3. Open Pump Module door. Administration set’s Flo–Stop®

Device will automatically close to prevent accidental free-
flow.
4. Remove administration set Flo-Stop® Device first, by gently

pulling tubing (below Air-in-Line Detector) forward and out,
and then lifting upper fitment vertically from upper fitment
recess.
GETTING STARTED 29
Changing and Reloading Set During Infusion (Continued)
5. Prime and load a new administration set, as described in

“Preparing Infusion” section.
6. Close Pump Module door.
8. Press VTBI soft key and use numeric data entry keys to enter
desired VTBI.
9. Open roller clamp.
Drug Calculation Parameters
The MEDLEY™ System uses the following parameters entered by

the user during the drug calculation setup procedure:
• Bolus dose units: Units device will use in calculating bolus
dose. Bolus dose units are selected, by user, from alternatives
provided.
• Diluent volume: Volume of fluid used as diluent for drug
(mL).
• Dosing units: Units device will use in calculating continuous
infusion drug dose. Dosing Units are selected, by user, from
alternatives provided.
• Drug amount: Amount of drug in IV container (gram, mg,
mcg, mEq or units).
• Patient weight: Weight of patient (kg); this is an optional
parameter that is not needed unless drug dose is normalized
for patient weight.
• Time units: Time base for all calculations (minute or hour).
The bolus dose, drug dose and flow rate parameters are
calculated using the above parameters, as follows:
• Bolus dose = Bolus dose x Patient weight (if used).
• Bolus dose duration = Bolus VTBI / Bolus rate.
• Bolus dose VTBI = Bolus dose / Drug concentration.
• Bolus rate = Bolus VTBI / Duration.
• Drug concentration = Drug amount / Diluent volume.
• Drug dose = Flow rate x Drug concentration (normalized for
patient weight if specified by entering a patient weight).
• Flow rate = Drug dose / Drug concentration (normalized for
patient weight if specified by entering a patient weight).
30 GETTING STARTED
Setting Up Drug Calculation with Drug Library
To access the Drug Library, a hospital-defined best-practice data WARNING

set must be uploaded and the Profiles feature enabled. The Drug Calculation feature is to be
used only by personnel properly
trained in the administration of
continuously infused medications.
Extreme caution should be exercised
to ensure the correct entry of the
drug calculation infusion parameters.
References in this document to
specific drug and drug doses are only
examples. Refer to specific drug
GETTING STARTED
product labeling for information
concerning appropriate
administration techniques and
dosages.
1. Prime and load set as previously described. A Channel Options 1 of 1

2. Press CHANNEL SELECT key on Pump Module. Pressure Limit - P
Channel Labels
3. Press OPTIONS key on Programming Module.
4. Press Drug Calculation Setup soft key.

EXIT
EXIT
5. Press DRUG LIBRARY soft key. A Drug Calculation

DRUG
AMOUNT ____ mcg
DILUENT
VOLUME mg
PATIENT
PATIENT
WEIGHT gram
TIME
UNITS unit
DOSING
UNITS mEq
>Enter Amount of Drug in

Container
DRUG
LIBRARY
6. Press soft key next to desired drug and concentration. A Drug Calculation
Adult ICU
aminophylline 500mg/250mL A-E
Use alpha-index speed select, and/or PAGE UP and PAGE
bretylium 500 mg/250mL F-J
DOWN soft keys, to view available drugs/concentrations.
dopamine ___mg/___mL K-O
dopamine 400mg/250mL P-T
dopamine 800mg/250mL U-Z
>Select Drug Name
EXIT PAGE
DOWN
GETTING STARTED 31
Setting Up Drug Calculation with Drug Library (Continued)
7. Confirm selected drug/concentration is drug to be A Drug Calculation

Adult ICU
administered. dopamine Yes

400mg in 250mL was
No
• Press Yes soft key to continue programming.
selected.
Is this correct?
DOSING
mcg/kg/min
• Press No soft key to change selection.
UNITS
NOT BOLUSABLE
• Bolus dose units appear if Bolus Dose is enabled.

• Anesthesia Mode appears if enabled. >Press Yes or No
8. DRUG AMOUNT, DILUENT VOLUME, TIME UNITS and DOSING A Drug Calculation
dopamine
UNITS are automatically entered for selected drug. DRUG
AMOUNT 400 mg
• If hospital practice guidelines identify selected drug as
DILUENT
VOLUME 250 mL
PATIENT
_ 70 kg
weight-based, system will prompt for a patient weight in
WEIGHT
TIME
Min
kilograms.
UNITS
DOSING
UNITS mcg/kg/min
[Conc]: 1600 mcg/mL
NOTE: If a patient’s weight has been previously entered, it >Press NEXT to Confirm
is automatically displayed. It can be added without
affecting the weight-based continuous infusions on this DRUG
LIBRARY
NEXT
channel.
• If selected drug is not weight-based, system will not
permit a patient weight entry.
9. Review drug calculation setup parameter. If setup is
correct, press NEXT soft key to confirm.
10. Press either RATE or DOSE soft key. A Drug Calculation

dopamine
CONTINUOUS INFUSION
RATE _ _ _ mL/h
VTBI _ _ _ _ mL
DOSE _ _ _ _ _ mcg/kg/min
[Conc]: 1600 mcg/mL

>Select RATE or DOSE
SETUP
11. Use numeric data entry keys to enter rate or dose value A Drug Calculation
dopamine
(other value is calculated and displayed). CONTINUOUS INFUSION
RATE 13.1 mL/h
NOTE: In the Drug Calculation mode, the device infuses at VTBI _ _ _ _ mL
the calculated rate rounded to the nearest one-hundredth of a DOSE _ _ _ _5 mcg/kg/min
mL per hour. The rate shown on the Main Display, Channel
Programming screen is this rate. The rate shown in the [Conc]: 1600 mcg/mL
Channel Rate Display will be rounded to the nearest one-tenth >Select VTBI
of a mL per hour.
SETUP
32 GETTING STARTED
Setting Up Drug Calculation with Drug Library (Continued)
12. Press VTBI soft key. Drug Calculation

dopamine
CONTINUOUS INFUSION
13. Use numeric data entry keys to enter volume-to-be-infused. RATE 13.1 mL/h
VTBI 250 mL
NOTE: At rates less than 10 mL/h, the rate is displayed to two DOSE 5 mcg/kg/min
decimal places and the VTBI can be entered and is displayed to
two decimal places. [Conc]: 1600 mcg/mL
>Press START
PAUSE SETUP START
14. Verify drug parameters are correct and then press START soft Midtown Hospital
Adult ICU
key. A VTBI = 250.0 mL
GETTING STARTED
• Rate appears in Channel Rate Display. B
C
NOTE: If a dose outside of the Guardrails® Limits has been D
entered and verified as correct, the Channel Message Display
will also show either “LLL” for a low dose or “↑↑↑” for a high
dose.
VOLUME AUDIO
• Dose and drug name scroll in Channel Message Display. INFUSED ADJUST
• Main Display alternates between VTBI and drug name with

dose.
Setting Up Drug Calculation for Non-Library Drugs

1. Prime and load set as previously described. WARNING
2. Press CHANNEL SELECT key on Pump Module. The Drug Calculation feature is to be
used only by personnel properly
3. Press OPTIONS key on Programming Module. trained in the administration of
continuously infused medications.
Extreme caution should be exercised
to ensure the correct entry of the
drug calculation infusion parameters.
References in this document to
specific drug and drug doses are only
examples. Refer to specific drug
product labeling for information
concerning appropriate
administration techniques and
dosages.
4. Press Drug Calculation Setup soft key. A Drug Calculation

DRUG
AMOUNT ____ mcg
DILUENT
VOLUME mg
PATIENT
PATIENT
WEIGHT gram
TIME
UNITS unit
DOSING
UNITS mEq
>Enter Amount of Drug in

Container
DRUG
LIBRARY
GETTING STARTED 33
Setting Up Drug Calculation for Non-Library Drugs (Continued)
5. Use numeric data entry keys to enter amount of drug added A Drug Calculation
to IV container. DRUG
AMOUNT 400 mcg
DILUENT
VOLUME mg
6. Press soft key for appropriate unit of measure for DRUG PATIENT
PATIENT
WEIGHT gram
AMOUNT. TIME
UNITS unit
DOSING
UNITS mEq
>Select Unit of Measure
DRUG
LIBRARY
7. Use numeric data entry keys to enter diluent volume. A Drug Calculation
DRUG
AMOUNT 400 mg
DILUENT
VOLUME _250 mL
PATIENT
WEIGHT
TIME
UNITS
DOSING
UNITS
[Conc]: 1600 mcg/mL

>Select PATIENT
WEIGHT
DRUG
LIBRARY
8. Press PATIENT WEIGHT soft key. A Drug Calculation

DRUG
400 mg
9. Press either Yes or No soft key to indicate whether patient
AMOUNT
DILUENT
250 mL Yes
weight is to be used in Drug Calculation.
VOLUME
PATIENT
WEIGHT >>>> No
Note: Press “Yes” only if Patient
NOTE: Do not enter a patient weight if weight is not used in weight is used in the calculation.
For Example: Dosing units =
the calculation. mg/kg/h
>Use Patient Weight in

Calculation?
DRUG
LIBRARY
10. Use numeric data entry keys to enter patient weight in A Drug Calculation
kilograms (if required) and then press ENTER. DRUG
AMOUNT 400 mg
DILUENT
VOLUME 250 mL
PATIENT
WEIGHT _ _70 kg
TIME
UNITS
DOSING
UNITS
[Conc]: 1600 mcg/mL

>Select Time Units
DRUG
LIBRARY
11. Press either Min, Hour or Day soft key to select time base A Drug Calculation
for drug calculation. DRUG
AMOUNT 400 mg
DILUENT
VOLUME 250 mL
PATIENT
WEIGHT 70 kg Min
TIME
UNITS >>>> Hour
DOSING
UNITS Day
[Conc]: 1600 mcg/mL
>Select Time Units
DRUG
LIBRARY
34 GETTING STARTED
12. Press soft key next to desired DOSING UNITS. A Drug Calculation
DRUG
AMOUNT 400 mg
DILUENT
VOLUME 250 mL
PATIENT
WEIGHT 70 kg
TIME
UNITS mcg/kg/min
DOSING >> mg/kg/min
UNITS
[Conc]: 1600 mcg/mL

>Select the Desired
Dosing Units
DRUG
LIBRARY
13. Verify correct drug calculation infusion parameter input and A Drug Calculation
press NEXT soft key. DRUG
400 mg
GETTING STARTED
AMOUNT
DILUENT
VOLUME 250 mL
PATIENT
WEIGHT 70 kg
TIME
UNITS Min
DOSING
UNITS mcg/kg/min
[Conc]: 1600 mcg/mL
>Press NEXT to Confirm
DRUG
LIBRARY
NEXT
14. Press either RATE or DOSE soft key. Drug Calculation

CONTINUOUS INFUSION
RATE _ _ _ mL/h
VTBI _ _ _ _ mL
DOSE _ _ _ _ _mcg/kg/min
[Conc]: 1600 mcg/mL

>Select RATE or DOSE
SETUP BOLUS
15. Use numeric data entry keys to enter rate or dose value Drug Calculation
(other value is calculated and displayed). CONTINUOUS INFUSION
RATE 13.1 mL/h
NOTE: In the Drug Calculation mode, the device infuses at VTBI _ _ _ _ mL
the calculated rate rounded to the nearest one-hundredth of a DOSE _ _ _ _5 mcg/kg/min
mL per hour. The rate shown on the Main Display, Channel
Programming screen is this rate. The rate shown in the [Conc]: 1600 mcg/mL
Channel Rate Display will be rounded to the nearest one-tenth >Select VTBI
of a mL per hour. SETUP BOLUS
GETTING STARTED 35

CONTINUOUS INFUSION
17. Use numeric data entry keys to enter volume–to-be-infused. RATE 13.1 mL/h
VTBI 250 mL
>Press START
PAUSE SETUP BOLUS START
18. Verify parameters are correct and then press START soft key: Midtown Hospital
Adult ICU
VTBI = 250.0 mL
• Rate appears in Channel Rate Display.
• Dose scrolls in Channel Message Display.
• VTBI (volume remaining) appears in Main Display.
VOLUME AUDIO
INFUSED ADJUST
Setting Bolus Dose (Drug Calculation with Drug Library)
This section provides the procedure on how to program a bolus

at the beginning of an infusion with a drug calculation
programmed using the Drug Library.
NOTE: If Bolus is enabled, the BOLUS DOSE soft key will appear in
the Drug Calculation screen.
1. Set up Drug Calculation as described in “Setting Up Drug Drug Calculation

lidocaine
Calculation with Drug Library” section, steps 1–13. CONTINUOUS INFUSION
RATE 135 mL/h
VTBI 250 mL
DOSE 9 mg/min
[Conc]: 4 mg/mL
>Press START
36 GETTING STARTED
Setting Bolus Dose (Drug Calculation with Drug Library) (Continued)
2. Press BOLUS soft key. A Drug Calculation

lidocaine
Dose exceeds the Yes
NOTE: If the programmed continuous infusion is outside the Guardrail limit of 8
mg/min. No
Guardrails® Limit for that care area, a prompt will appear Proceed?
before the bolus dose can be programmed. If Yes soft key is

pressed, programming will continue; if No soft key is pressed,
the infusion will need to be reprogrammed.
>Press Yes or No
A Drug Calculation
lidocaine
BOLUS DOSE
GETTING STARTED
DOSE _ _ _ _ mg/kg
PATIENT
WEIGHT
DURATION
BOLUS VTBI = mL
[Conc]: 4 mg/mL
>Enter Bolus Dose
CONTI-
SETUP NUOUS
3. Use numeric keypad entry keys to enter desired bolus dose. A Drug Calculation
lidocaine
Enter patient weight. BOLUS DOSE
DOSE 1.00 mg/kg
4. Press DURATION soft key. Press MAX RATE soft key to PATIENT
WEIGHT 70.00 kg
automatically calculate duration or use numeric keypad DURATION 1 min Max
Rate
entry keys to enter desired duration. BOLUS VTBI = 17.5 mL
[Conc]: 4 mg/mL
NOTE: The MAX RATE soft key allows the bolus dose to be >Press Start to Begin
programmed to infuse at the maximum rate for that profile. Infusing Bolus Dose
CONTI-
The bolus DURATION would be automatically calculated.
PAUSE SETUP NUOUS START
5. Press START soft key to begin bolus infusion. Midtown Hospital

Adult ICU
A Bolus VTBI = 17.5 mL
VOLUME AUDIO
Main screen alternates between BOLUS VTBI and drug name

INFUSED ADJUST
with dose. Midtown Hospital

Adult ICU
A lidocaine
1 mg/kg Bolus
VOLUME AUDIO
INFUSED ADJUST
GETTING STARTED 37
Setting Bolus Dose (Drug Calculation with Drug Library) (Continued)
6. During any bolus infusion, press CHANNEL SELECT key on A Drug Calculation
lidocaine
Pump Module to see detail screen. BOLUS DOSE

Dose
Remaining: 0.085 mg
Pt. Weight:70 kg
Time Left: <1 min Rate
Max
BOLUS VTBI = 0.4 mL

[Conc]: 4 mg/mL
>Press Start to Continue
Infusing Bolus Dose
STOP
PAUSE BOLUS START
7. At conclusion of bolus infusion: Midtown Hospital

Adult ICU
• System beeps twice. A VTBI = 241.3 mL
• “BOLUS DOSE COMPLETE” scrolls in Channel Message

Display.
• Continuous infusion initiates.
VOLUME AUDIO
NOTE: During continuous infusion, main screen alternates INFUSED ADJUST
between VTBI and drug name with dose.

Midtown Hospital
Adult ICU
A lidocaine
9 mg/min
VOLUME AUDIO
INFUSED ADJUST
Setting Bolus Dose (Drug Calculation for Non-Library Drugs)
This section provides the procedure on how to program a bolus

at the beginning of an infusion with a drug calculation
programmed without the use of the Drug Library.
NOTE: If Bolus is enabled, the BOLUS DOSE soft key will appear in
the Drug Calculation screen.
1. Set up Drug Calculation as described in “Setting Up Drug Drug Calculation

Calculation for Non-Library Drugs” section, steps 1–15. CONTINUOUS INFUSION
RATE 13.1 mL/h
VTBI mL
DOSE 5 mcg/kg/min
[Conc]: 1600 mcg/mL

>Select VTBI
SETUP BOLUS
38 GETTING STARTED
Setting Bolus Dose (Drug Calculation for Non-Library Drugs) (Continued)

CONTINUOUS INFUSION
3. Use numeric data entry keys to enter Volume–to-be-Infused. RATE 13.1 mL/h
VTBI 250 mL
>Press START
4. Press BOLUS soft key.
5. Use numeric keypad entry keys to enter desired bolus dose. A Drug Calculation
Press soft key next to desired dosing unit. BOLUS DOSE mcg
GETTING STARTED
DOSE _ _500 mcg/kg
NOTE: In this example, mcg was selected as the dosing unit PATIENT
WEIGHT mg
so a PATIENT WEIGHT entry can not be made. DURATION mg/kg
BOLUS VTBI =
[Conc]: 1600 mcg/mL
>Select the Desired
Dosing Units
CONTI-
SETUP NUOUS
6. Press MAX RATE soft key to automatically calculate duration A Drug Calculation
or press DURATION soft key and use numeric keypad entry BOLUS DOSE
keys to enter desired duration. DOSE 500.0 mcg
PATIENT
WEIGHT Not Used
NOTE: The MAX RATE soft key allows the bolus dose to be DURATION <1 min Max
Rate
programmed to infuse at the maximum rate for that profile. BOLUS VTBI = 0.313 mL
The bolus DURATION would be automatically calculated. [Conc]: 1600 mcg/mL
>Press Start to Begin
7. Press START soft key to begin bolus infusion. Infusing Bolus Dose
CONTI-
PAUSE SETUP NUOUS START
BOLUS VTBI counts down on main screen. Midtown Hospital

Adult ICU
A BOLUS VTBI = 0.3 mL
VOLUME AUDIO
INFUSED ADJUST
GETTING STARTED 39
8. During any bolus infusion, press CHANNEL SELECT key on A Drug Calculation
Pump Module to see detail screen. BOLUS DOSE
Dose
Remaining: 400 mcg
Pt. Weight: Not Used
Time Left: <1 min Max
Rate
BOLUS VTBI = 0.25 mL
[Conc]: 1600 mcg/mL
>Press START to Continue
Infusing Bolus Dose
STOP
PAUSE BOLUS START
9. At conclusion of bolus infusion: Midtown Hospital

Adult ICU
• System beeps twice. A VTBI = 249.5 mL
• “BOLUS DOSE COMPLETE” scrolls in Channel Message

Display.
• Continuous infusion initiates.
VOLUME AUDIO
INFUSED ADJUST
Stopping Bolus Dose
1. Press CHANNEL SELECT key on Pump Module.

2. Press STOP BOLUS soft key.
3. To stop bolus and start continuous infusion, press Yes soft
key.
4. To stop continuous infusion, press and hold CHANNEL OFF
key for 2 seconds.
Restoring Bolus Dose

A bolus dose can be restored after it has completed, either prior
to or after the channel has been turned off, as indicated in the
following sections.
Bolus Dose Completed - Channel Not Turned Off

2. Press BOLUS soft key.
3. Press RESTORE soft key.
4. Verify dosing parameters and press START soft key.
40 GETTING STARTED
Restoring Bolus Dose (Continued)
Bolus Dose Completed - Channel Turned Off

3. Verify Drug Calculation screen and press NEXT soft key.
4. Verify dosing parameters and press BOLUS soft key.
6. Verify dosing parameters and press START soft key.
GETTING STARTED
Anesthesia Mode
When the MEDLEY™ System is operating in Anesthesia Mode, a

channel can be paused indefinitely without an alarm and the
air–in–line limits can be set for up to 500 microliters. Anesthesia
Mode also makes it possible to have additional drugs in each
profile, which are only accessible when operating in Anesthesia
Mode.
NOTE: When the MEDLEY™ System is set up for use in Anesthesia

Mode, it is important to select the profile that corresponds with the
care area the patient will be taken to when the Anesthesia Mode is
discontinued. This will ensure that the MEDLEY™ System will be in
the correct profile following the use of the Anesthesia Mode.
Enabling Anesthesia Mode
1. Press OPTIONS key on Programming Module.

2. Press Anesthesia Mode soft key. System Options 1 of 2
Display Contrast
Time of Day
Power Down All Channels
Anesthesia Mode
Battery Runtime
EXIT
PAGE
EXIT DOWN
GETTING STARTED 41
Anesthesia Mode (Continued)
Enabling Anesthesia Mode (Continued)
3. Press Enable soft key. System Options

Anesthesia Mode
4. Press CONFIRM soft key. Enable
Disable
Air Detection = Change

75 microliters
Select an Option or Press

CONFIRM
CONFIRM
5. Press soft key corresponding to channel Anesthesia Mode Midtown Hospital

Adult ICU
infusion is to be programmed on. A
B
6. Program Anesthesia Mode infusion using same procedure C
as for any other continuous infusion. D
NOTE: In Anesthesia Mode, when a channel with a drug

calculation infusion is turned off and then turned back on, Anesthesia Mode
pressing the RESTORE soft key will bypass the Drug VOLUME AUDIO
Calculation Setup screen and go directly to the Continuous

INFUSED ADJUST
Infusion screen.
Disabling Anesthesia Mode
The Anesthesia Mode can be disabled, and normal operation Midtown Hospital
Adult ICU
resumed, using either of the following three methods: A
B
• System Options menu.
C
• Disconnecting system from AC power.
D
• Connecting system to AC power.
From System Options Menu Anesthesia Mode
VOLUME AUDIO
1. While operating in Anesthesia Mode, press OPTIONS key on

INFUSED ADJUST
Programming Module.
System Options 1 of 2
2. Press Anesthesia Mode soft key. Display Contrast
Time of Day
Power Down All Channels
Anesthesia Mode
Battery Runtime
EXIT
PAGE
EXIT DOWN
42 GETTING STARTED
Anesthesia Mode (Continued)
Disabling Anesthesia Mode (Continued)
From System Options Menu (Continued)

System Options
3. Press Disable soft key. Anesthesia Mode
4. Press confirm soft key. “Anesthesia Mode” is no longer Enable

Disable
displayed on Main Display, indicating it has been disabled.
Air Detection = Change
75 microliters
>Select an Option or Press

CONFIRM
GETTING STARTED
CONFIRM
Disconnecting System from AC Power While

in Anesthesia Mode
1. If system is connected to AC power while running in
Anesthesia Mode, disconnect system from AC.
• Anesthesia Mode is automatically disabled.
• All currently running infusions continue.
• A prompt appears as an alert that Anesthesia Mode has
been discontinued.
Anesthesia mode was discontinued
2. Press CONFIRM soft key. when AC power cord was
disconnected. Press CONFIRM to
continue normal operation.
CONFIRM
Connecting System to AC Power While in

Anesthesia Mode
1. Connect system to AC power.
2. Press YES soft key to continue using Anesthesia Mode while AC power cord was
Yes
connected to AC power. connected.
Continue
ANESTHESIA MODE? No
>Select Yes or No
GETTING STARTED 43
Reviewing Serial Number
1. Press OPTIONS key on Programming Module. Serial Number Review

PM: nnnn-nnnnnnnn
2. Press Page Down soft key and then press Serial Numbers Module A: nnnn-nnnnnnnn
soft key. Module B: nnnn-nnnnnnnn
Serial numbers for Programming Module and all attached Module C: nnnn-nnnnnnnn
channels are displayed as shown.

Module D: nnnn-nnnnnnnn
>Press CANCEL or EXIT

3. Press EXIT soft key to return to main screen.
EXIT
Reviewing Software Version
1. Press OPTIONS key on Programming Module. System Options 2 of 2

System Configuration
2. Press PAGE DOWN soft key and then press Software Versions Serial Numbers
soft key. Software Versions
Guardrails Event Counter
EXIT
PAGE EXIT
UP
3. Press View soft key next to desired channel. Software Rev. Review
PM: View
4. Press EXIT soft key to return to Software Review screen. Module A: View
View
5. Press EXIT soft key to return to main screen. Module B:
Module C: View
Module D: View
EXIT
EXIT
44 GETTING STARTED
ALARMS, ADVISORIES AND PROMPTS
To enhance safety and ease of operation, the MEDLEY™ System provides a full range of audio and visual
alarms, advisories and prompts.
Definitions
Advisory A sequence of audio and/or visual signals indicating the operating status of the
MEDLEY™ Medication Safety System. The audio may be silenced for
approximately two minutes by pressing the SILENCE key on the Programming
Module.
Alarm An audio and visual signal that a potentially unsafe condition is present.
Immediate action is required. The audio may be silenced for approximately
two minutes by pressing the SILENCE key on the Programming Module.
Error An audio and/or visual signal that a failure has been detected. Immediate
action is required.
Guardrails® Advisory A visual popup requiring a “Yes” or “No” response; designed to help reduce
programming errors.
Prompt An audio and/or visual signal, appearing on the bottom line of the Main
ALARMS, ADVISORIES
Display or the Channel Message Display, to perform some action. The audio
AND PROMPTS
may be silenced for twelve seconds by pressing the SILENCE key on the
Programming Module.
ALARMS, ADVISORIES AND PROMPTS 45

Audio Characteristics
The Programming Module and Main Display provide four types of alert information: advisories, prompts,
alarms, and malfunctions. The characteristics of the accompanying audio sounds are as follows:
Type Sound Notes
Advisory One short beep every two seconds Variable volume; can be silenced for
two minutes.
Alarm Choice of three alarm audio profiles, Variable volume; can be silenced for
selectable in System Configuration two minutes.
Error (Hardware Detected) Pairs of long beeps Fixed maximum decibel volume;
cannot be silenced.
Error (Software Detected) Pairs of long beeps Fixed maximum decibel volume; can
be silenced for two minutes.
Illegal Key Press Two short beeps Variable volume; cannot be silenced.
Key Click One short beep Fixed minimum volume; can be

silenced and disabled in the System
Configuration.
Prompt One short beep every two seconds Variable volume; can be silenced.
Switchover Six short beeps Variable volume; can be silenced and

disabled in the System
Configuration.
46 ALARMS, ADVISORIES AND PROMPTS

Alarms
Alarm Meaning Response
Accumulated Air-in-Line A large number of air bubbles Clear air from line and press RESET
smaller than current air-in-line limit soft key, and then press RESTART key
has recently passed detector. to continue infusion.
Air-in-Line Air has been detected in set during Ensure tubing is properly installed in
an infusion. Infusion stops on Air-in-Line Detector. If air is present,
affected channel. clear air from administration set.
Press RESTART key or appropriate
CHANNEL SELECT key and then press
START soft key.
Channel Disconnected Channel(s) have either been Press CONFIRM soft key to silence
disconnected while in operation or alarm and clear message from
have a communication problem. screen. Reattach channel if desired.
If alarm is still present, replace
channel with an operable
instrument.
Check IV Set Administration set is not properly Close roller clamp, remove and
installed. Infusion stops on affected reinstall administration set, close
channel. door, open roller clamp and then
ALARMS, ADVISORIES
press RESTART key.
AND PROMPTS
Close Door Door opened during an infusion. Close door, press RESTART key or
Infusion stops on affected channel. appropriate select control and then
press START soft key.
Flo-Stop Open - Close Door The Flo-Stop® Device is in open Close roller clamp on administration
position while door is open. set or close door.
Occluded - Fluid Side/Empty Indicates either upstream occlusion Clear occlusion on fluid side of
Container or empty container. Infusion stops device. If necessary, refill drip
on affected channel. chamber. Press RESTART or CHANNEL
SELECT key and then press START soft
key.
Occluded - Patient Side Increased back pressure sensed while Clear occlusion, press RESTART key or
infusing in the pump delivery mode. appropriate select control and then
Infusion stops on affected channel. press START soft key.
Partial Occlusion - Patient Side A partial occlusion of the patient Clear occlusion, press RESTART key or
side of IV line has been detected by appropriate select control and then
the AutoRestart feature. press START soft key.
Restart Channel Door was opened during an infusion Close door, press RESTART key or
and then closed. Infusion stops on appropriate channel select control
affected channel. and then press START soft key.

Advisories
Advisory Meaning Response
Anesthesia Mode Anesthesia Mode has been enabled. None
Bolus Dose Complete Channel is running in continuous None

infusion mode if programmed.
Checking Line A patient side occlusion has None

occurred and AutoRestart feature is
monitoring downstream pressure to
determine if infusion can continue.
Infusion Complete - KVO Programmed volume-to-be-infused Set up a new infusion or press

has been delivered; channel is CHANNEL OFF key.
running at KVO rate.
Panel Locked Occurs following a key press when If appropriate, deactivate Tamper
Tamper Resist feature is active. Resist feature using Tamper Resist
Control on back of Programming
Module.
Panel Unlocked Occurs when Tamper Resist feature is None.

deactivated.
Pause Pause control has been pressed; To resume infusion, press RESTART
infusion is stopped. key, or press CHANNEL SELECT key
and then press START soft key.
Secondary A secondary infusion is in progress None. When secondary VTBI=”0”,

on indicated channel. infusion will revert to programmed
primary parameters.

Errors
Error Meaning Response
Channel Error System has detected an error on a Press CONFIRM soft key to silence
pumping channel. Infusion stops on alarm and continue operation of
affected channel. unaffected channels. Replace Pump
Module with an operational unit as
required. Service by qualified
personnel is required.
ALARMS, ADVISORIES
AND PROMPTS

T H I S PA G E
I N T E N T I O N A L LY
LEFT BLANK

MAINTENANCE
The MEDLEY™ System Technical Service Manual is available from ALARIS Medical Systems and includes
routine service schedules, circuit diagrams, component parts lists and descriptions, calibration and test
procedures, and other technical information, to assist qualified service personnel in repair and
maintenance of the instrument’s repairable components. Maintenance procedures are intended to be
performed only by qualified personnel.
Specifications
Accumulated Air Window: Single Bolus Volume Window % Air that Causes
Setting (mL) Alarm
50 2.8 10%
75 8.0 20%
250 8.0 30%
*500 12.0 30%
* In Anesthesia Mode only.
Bolus Volume following Pressure Limit (mmHg)

Occlusion, Maximum:
Rate (mL/h) 50 525
25 ≤0.3 mL ≤0.6 mL
Critical Volume: The maximum over-infusion which can occur in the event of a single fault condition is
0.6 mL.
Dimensions: 3.3"W x 8.9"H x 5.5"D
Environmental Conditions: Operating Storage/Transport

Temperature Range: 41 to 104°F -4 to 140°F
(5 to 40°C) (-20 to 60°C)
Relative Humidity: 20 to 90% 5 to 85%
(Avoid prolonged exposure Noncondensing Noncondensing
to relative humidity >85%)
MAINTENANCE
Atmospheric Pressure: 525 to 4560 mmHg 375 to 760 mmHg
(700 to 6080 hPa) (500 to 1013 hPa)
Equipment Orientation: To ensure proper operation, the system must remain in an upright position.
Electrical Classification: Class 1, Type CF Defibrillator Proof
Flow Rate Programming Rate Range Increments (mL/h)

Increments: (mL/h) User Input Rates Device Calculated Rates
0.1 - 9.99 0.01
0.1
10 - 99.9 0.1
100 - 999 1 1
Fluid Ingress Protection: IPX1, Drip Proof
MAINTENANCE 51
Specifications (Continued)
Infusion of Air, Means to

Protect Patient from: Ultrasonic Air-in-Line Detection
Maximum single bolus size = selectable 50, 75 or 250 microliters nominal (500 microliters
in Anesthesia Mode)
Infusion Pressure,
Maximum: 683 mmHg
KVO (Keep Vein Open)

Rate: Factory Default Setting is 1.0 mL/h if set rate is 1.0 mL/h or above; or set rate, if rate is
0.9 mL/h or below.
KVO Selection Range: KVO rate can be set in System Configuration from 0.1-20 mL/h in 0.1 mL/h increments.
Occlusion Alarm Thresholds:

Pump Mode: 525 mmHg at rates ≥30 mL/h
Varying level based on rate and patient back–pressure at rates <30 mL/h.
Selectable Mode: User selected from 50 to 525 mmHg in 25 mmHg increments.
Operating Principle: Positive displacement
Rate Accuracy: Rate accuracy of the MEDLEY™ Medication Safety System is ±5% at rates between 1.0 and
999 mL/h and ±5.5% at rates <1.0 mL/h, 95% of the time with 95% confidence, under the
conditions listed below. (Refer to the Trumpet and Start-Up Curves for additional
information.)
Infusion Rate Range: 0.1 to 999 mL/h
Ambient Temperature: 68 ±4°F (20 ±2°C)
Source Container Height: 20 inches above the top of the Pump Module
Test Solution: Distilled Water
Distal Back pressure: 0 mmHg (0 kPa)
Needle: 18 gauge
Set Model 2210
WARNING
Variations of head height, back pressure or any combination of these may affect
rate accuracy. Factors that can influence head height and back pressure are: IV
set configuration, IV solution viscosity and IV solution temperature. Back
pressure may also be affected by type of catheter. Refer to the “APPENDIX –
Trumpet and Start-Up Curves” for data on how these factors influence rate
accuracy.
Time to Alarm, Maximum: Pressure Limit (mmHg)

Rate (mL/h) 50 525
1 ≤5 minutes ≤45 minutes
25 ≤15 seconds ≤2 minutes
52 MAINTENANCE
Specifications (Continued)
Volume to be Infused Range Increments

Programming Increments: (mL) (mL)
0.1 - 9.99 0.01

10 - 999.9 0.1
1000 - 9999 1
Weight: 2.5 lbs
NOTE: Compliance to Standards

The MEDLEY™ Medication Safety System has been assessed and complies with the following standards:
UL 2601–1, including A1 and A2; CSA C22.2 No. 601.1, including A1 and A2; IEC/EN 60601-2-24;
IEC/EN 60601–1-2, and AAMI ID26.
Configurable Settings
NOTE: With the Profiles feature enabled, the settings are configured independently for each profile. A hospital-
defined, best-practice data set must be uploaded to enable the Profiles feature. Date and Time is a system setting
and is the same in all profiles.
System Settings
Feature Default Setting Options

Alarm Audio Profile 1 Profile 1, 2 or 3
Anesthesia Mode Disabled Enabled - Disabled
Battery Meter Disabled Enabled - Disabled
Clock Setup (Date and Time) N/A Set date and time
MAINTENANCE
Key Click Audio Enabled Enabled - Disabled
Max Patient Weight 500 kg 0.1 - 500 kg
Tamper Resist Disabled Enabled - Disabled
MAINTENANCE 53
Configurable Settings (Continued)
Pump Module Settings
Feature Default Setting Options

Accumulated Air-in-Line Enabled Enabled - Disabled
Air-in-Line Settings 75 microliters 50, 75 or 250 microliters
(single bolus) Anesthesia Mode only: 500 microliters
AutoRestart Attempts 0 0-9 attempts
Anesthesia Mode only: 9 attempts
Drug Calculation Disabled Enabled - Disabled
• Bolus Dose Disabled Enabled - Disabled
KVO Rate Adjust 1 mL/h 0.1 - 20 mL/h
(“Keep Vein Open”)
Max Rate 999 mL/h 0.1-999 mL/h in 0.1 mL/h increments to
99.9, then 1.0 mL/h increments from
100 to 999 mL/h.
Max VTBI 9999 mL 0.1-9999 mL
Pressure Dynamic Disabled Enabled - Disabled
(“Dynamic Pressure Display”)
Pressure Mode Pump (P); Unlocked Pump (P), Selectable (S); Locked or
Unlocked
Profiles Disabled Enabled - Disabled
SEC to PRI Alert Enabled Enabled - Disabled
Secondary Disabled Enabled - Disabled
(“Dual Rate Sequential Piggybacking”)
Volume/Duration Infusion Disabled Enabled - Disabled
Check-In and Configuration

Directions for Use.
Cleaning

Directions for Use.
54 MAINTENANCE
Inspection Requirements
To ensure the system remains in good operating condition, both

regular and periodic inspections are required.
Regular inspections consist of a visual inspection for damage WARNING

and cleanliness, and performing the procedure described in the
Failure to perform these inspections
Start-Up Sequence section of this directions for use before each
may result in improper instrument
usage of the instrument. Regular inspections are not covered
operation.
under any contract or agreement offered by ALARIS Medical
Systems and must be performed by the user.
REGULAR INSPECTIONS
PROCEDURE FREQUENCY
INSPECT FOR DAMAGE:
Enclosure Each usage
I/O Connector Each usage
CLEANING As required
START-UP SEQUENCE Each usage
Periodic inspections of the hardware are required. For detailed

instructions on performing periodic inspections and
maintenance, refer to the MEDLEY™ Technical Service Manual
and supplemental service bulletins. A service agreement may be
obtained from ALARIS Medical Systems for the performance of
all required periodic inspections.
NOTE: Periodic inspections should only be performed by qualified

service personnel.
Service Information
MAINTENANCE
Directions for Use.
MAINTENANCE 55
WARRANTY
ALARIS Medical Systems, Inc., (hereinafter referred to as “ALARIS Medical Systems”) warrants that:
A. Each new ALARIS Medical Systems MEDLEY™ Medication Safety System is free from defects in
material and workmanship under normal use and service for a period of one (1) year from the
date of delivery by ALARIS Medical Systems to the original purchaser.
B. The main battery and each new accessory is free from defects in material and workmanship under
normal use and service for a period of ninety (90) days from the date of delivery by ALARIS Medical
Systems to the original purchaser.
If any product requires service during the applicable warranty period, the purchaser should
communicate directly with the relevant account representative to determine the appropriate repair
facility. Except as provided otherwise in this warranty, repair or replacement will be carried out at
ALARIS Medical Systems’ expense. The product requiring service should be returned promptly,
properly packaged and postage prepaid by purchaser. Loss or damage in return shipment to the
repair facility shall be at purchaser’s risk.
In no event shall ALARIS Medical Systems be liable for any incidental, indirect or consequential
damages in connection with the purchase or use of any ALARIS Medical Systems product. This
warranty shall apply solely to the original purchaser. This warranty shall not apply to any subsequent
owner or holder of the product. Furthermore, this warranty shall not apply to, and ALARIS Medical
Systems shall not be responsible for, any loss or damage arising in connection with the purchase or
use of any ALARIS Medical Systems product which has been:
(a) repaired by anyone other than an authorized ALARIS Medical Systems service representative;
(b) altered in any way so as to affect, in ALARIS Medical Systems’ judgment, the product’s stability or
reliability;
(c) subjected to misuse or negligence or accident, or which has had the product’s serial or lot number
altered, effaced or removed;
or
(d) improperly maintained or used in any manner other than in accordance with the written
instructions furnished by ALARIS Medical Systems.
This warranty is in lieu of all other warranties, express or implied, and of all other obligations or
liabilities of ALARIS Medical Systems, and ALARIS Medical Systems does not give or grant, directly or
indirectly, the authority to any representative or other person to assume on behalf of ALARIS Medical
Systems any other liability in connection with the sale or use of ALARIS Medical Systems products.
ALARIS Medical Systems DISCLAIMS ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY WARRANTY
OF MERCHANTABILITY OR OF FITNESS FOR A PARTICULAR PURPOSE OR APPLICATION.
See packing inserts for international warranty, if applicable.
56 MAINTENANCE
APPENDIX
Trumpet and Start-Up Curves
DESCRIPTION AND EXPLANATION OF TRUMPET AND FLOW CHARACTERISTICS UNDER VARYING

START-UP CURVES DELIVERY CONDITIONS
In this instrument, as with all infusion systems, Effects of Pressure Variations
the action of the pumping mechanism and
Under conditions of +100 mmHg pressure, the
variations in individual administration sets cause
MEDLEY™ Pump Module typically exhibits a long-
short-term fluctuations in rate accuracy. The
term accuracy offset of approximately –0.7%
following graphs show typical performance of
from mean values.
the system for both Pressure and Resistance
Modes in two ways: Under conditions of +300 mmHg pressure, the
MEDLEY™ Pump Module typically exhibits a long-
1. Accuracy during various time periods over term accuracy offset of approximately –4.2%
which fluid delivery is measured (trumpet from mean values.
curves).
Under conditions of -100 mmHg pressure, the
2. Delay in onset of fluid flow when infusion MEDLEY™ Pump Module typically exhibits a long-
commences (start-up curves). term accuracy offset of approximately +4.4%
from mean values.
Trumpet curves are named for their characteristic
shape. They display discrete accuracy data Resulting trumpet observation points typically
averaged over particular time periods or track those of accuracy; therefore, no significant
“observation windows”, not continuous data change in short–term variations result under
versus operating time. these pressure conditions.
Over long observation windows, short-term
Effects of Negative Solution Container Heights
fluctuations have little effect on accuracy, as
represented by the flat part of the curve. As the With a negative head height of -0.5 meters, the
observation window is reduced, short-term MEDLEY™ Pump Module typically exhibits a
fluctuations have greater effect, as represented long–term accuracy offset of approximately
by the “mouth” of the trumpet. Knowledge of –3.1% from mean values.
system accuracy over various observation Resulting trumpet observation points typically
windows may be of interest when certain drugs track those of accuracy; therefore, no significant
are being administered. change in short–term variations result under
Because the clinical impact of short-term negative head height conditions.
fluctuations on rate accuracy depends on the
half-life of the drug being infused and on the NOTE: Tests conducted in accordance with
degree of intravascular integration, the clinical IEC/EN 60601–2–24, “Particular requirements for
safety of infusion pumps and controllers” and
effect cannot be determined from the trumpet
AAMI ID26–1998 “Medical electrical equipment -
curves alone. Knowledge of the start-up Part 2: Particular requirements for the safety of
characteristics should also be considered. infusion pumps and controllers”, using MEDLEY™/
The start-up curves represent continuous flow Gemini Model 2210 Administration Sets.
APPENDIX
rate versus operating time for two hours from

the start of the infusion. They exhibit the delay in
onset of delivery due to mechanical compliance
and provide a visual representation of uniformity.
Trumpet curves are derived from the second hour
of this data.
APPENDIX 57
Trumpet and Start-Up Curves (Continued)
Start-Up at 0.1 mL/h (initial) Start-Up at 1 mL/h (initial)

Flow Rate (mL\h)
Flow Rate (mL\h)

Time (min)
Time (min)
Trumpet Curve
Trumpet Curve at
at 0.1
0.1mL/h
mL/h(initial)
(initial) Trumpet Curve at 1 mL/h (initial)
Flow Rate Error (%)

Flow Rate Error (%)
Observation Interval (min) Observation Interval (min)
Trumpet
TrumpetCurve
Curve at
at 0.1 mL/h (72
0.1 mL/h (72hrs)
hrs) Trumpet Curve at 1 mL/h (72 hrs)
Flow Rate Error (%)
Flow Rate Error (%)
Legend:
NOTE: The plot range has been P Maximum rate error
increased to ±100%, to allow Overall rate error
[
visualization of the graph. ◆ Minimum rate error
58 APPENDIX
Trumpet and Start-Up Curves (Continued)
Start-Up at 25 mL/h (initial) Start-Up at 999 mL/h (initial)
Flow Rate (mL\h)

Flow Rate (mL\h)
Time (min) Time (min)
Trumpet Curve at 25 mL/h (initial) Trumpet Curve at 999 mL/h (initial)

Flow Rate Error (%)
Flow Rate Error (%)
Trumpet Curve at 25 mL/h (72 hrs)

Trumpet Curve at 999 mL/h (24 hrs)
Flow Rate Error (%)
Flow Rate Error (%)

APPENDIX
Legend:
P Maximum rate error
Overall rate error
[
◆ Minimum rate error
APPENDIX 59
T H I S PA G E
I N T E N T I O N A L LY
LEFT BLANK
60 APPENDIX
®
ALARIS Medical Systems, Inc.

10221 Wateridge Circle
San Diego, California 92121 U.S.A.
Mail:
P.O. Box 85335
San Diego, California 92186-5335 U.S.A.
ALARIS®, ALARIS Medical Systems®, Flo-Stop®, Guardrails®, MEDLEY™, and SmartSite® are trademarks and registered trademarks of ALARIS Medical Systems,
Inc.
All other trademarks belong to their respective owners.
US Pat. Nos. 4,764,166; 4,690,673; 5,165,873; 5,601,445; 5,713,856; 5,781,442; 5,800,387; 5,836,910; 5,941,846; 6,347,553; AU Patent Nos. 634,811;
693,662; 703,178; 703,203; 719,254; 728,366; AT 0,225,158; BE Brevet Belge No. 0,225,158; CA Patented/Breveté 1,258,212; 2,026,518;
CH +0,225,158; DE D.B.P. Nos. 0,422,855; P3686558.3; FR Brevet Nos. 0,225,158; 0,422,855; GB Patent Nos. 0,225,158; 0,422,855; IT Brevettato Vol.
R.A. No. 0,225,158; JP Patent Nos. 1,816,872 ; 2,594,604 ; NL Ned. Octrooi No. 0,225,158; SE Sv. pat. nr 0,225,158; TW Patent No.
NI–107963. Other Patents Pending.
147029-003 Copyright© 2002 ALARIS Medical Systems, Inc. All Rights Reserved

Alaris Medley Pump Module 8100 Version 4b

Uploaded by

Copyright:

Available Formats

Alaris Medley Pump Module 8100 Version 4b

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Alaris Medley Pump Module 8100 Version 4b

Uploaded by

Copyright:

Available Formats

MEDLEY™

MEDICATION SAFETY SYSTEM

INFUSION PUMP MODULE

About the System

The MEDLEY™ Medication Safety System is a modular infusion

The MEDLEY™ Pump Module is intended for facilities that utilize

The MEDLEY™ Medication Safety System consists of the

The MEDLEY™ System uses a wide variety of ALARIS® MEDLEY™/

Contraindications: None known.

AutoRestart The AutoRestart feature is part of the MEDLEY™ System’s advanced

Guardrails® Prompt The Guardrails® Safety Software is designed to help prevent

Occlusion Pressure The MEDLEY™ System provides a complete range of Downstream

Volume/Duration The Volume/Duration infusion option allows the user to program a

Electrical Shock Protection Rating: Type CF, Defibrillation-proof

IPX1 Protection against fluid ingress: Drip Proof

! Attention: Refer to accompanying documentation.

IUI Connector: Inter-Unit Interface connector used to establish power and

Consult operating instructions.

Single-Use. Do not re-use.

XX ml Approximate set priming volume.

NOTE: Although the MEDLEY™ System is built and tested to Only

Warnings and Cautions

For WARNINGS and CAUTIONS for the Programming Module,

Epidural Administration WARNING

To ensure proper performance of the MEDLEY™ System and to

Administration Sets WARNING

User Precautions (Continued)

Operating Environment DANGER

User Precautions (Continued)

Radio Frequency Interference WARNING

Front/Side View - Door Closed

IUI Connector, Right

Alarm Infusing Standby

Channel Select Key - When

Pause Key - When pressed during

Channel Off Key - When pressed

Restart Key - When pressed, resumes

Front View - Door Open

IUI Connector, Left

Upper Pressure Sensor

Upper Pumping Finger

Door Latch Cam/Slide Lower Occluder

Lower Pumping Finger

Lower Pressure Sensor

Instruments are tested and calibrated before they are packaged

Unpacking the Pump Module

1. Remove Pump Module from its carton.

2. Verify door operates freely.

3. Verify membrane covering inside surface of pumping unit is

4. Check for loose parts.

5. Perform Periodic Inspection (see “Inspection Requirements”

6. Perform check-in procedure (see “Check-In and

Attaching and Detaching Channels

Refer to the MEDLEY™ Programming Module (Model 8000)

Powering On the System

1. Connect MEDLEY™ Programming Module to an external AC

2. Press SYSTEM ON key on Programming Module.

3. System self test begins:

Powering On the System (Continued)