R2

Booting `IOSv: flash0:vios-adventerprisek9-m (hd0,msdos1)'
Booted IOSv. Boot args: [/vios-adventerprisek9-m]
Smart Init is enabled
Restricted Rights Legend
Use, duplication, or disclosure by the Government is

subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.

170 West Tasman Drive
San Jose, California 95134-1706
Cisco IOS Software, IOSv Software (VIOS-ADVENTERPRISEK9-M), Version 15.9(3)M3,

RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2021 by Cisco Systems, Inc.
Compiled Wed 27-Jan-21 09:58 by prod_rel_team
This product contains cryptographic features and is subject to United

States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to

export@cisco.com.
Cisco IOSv (revision 1.0) with with 410857K/111616K bytes of memory.Installed

image archive
Processor board ID 96NU8C5VZLMTGTUN16DNO

8 Gigabit Ethernet interfaces
DRAM configuration is 72 bits wide with parity disabled.
256K bytes of non-volatile configuration memory.
2097152K bytes of ATA System CompactFlash 0 (Read/Write)
0K bytes of ATA CompactFlash 1 (Read/Write)
Press RETURN to get started!
*Mar 1 00:00:00.921: %ATA-6-DEV_FOUND: device 0x1F0

*Mar 1 00:00:04.084: %ATA-6-DEV_FOUND: device 0x1F1
*Mar 1 00:00:08.144: %NVRAM-5-CONFIG_NVRAM_READ_OK: NVRAM configuration
'flash:/nvram' was read from disk.
*Sep 22 11:20:29.463: %C3600-3-NOMAC: Can't allocate MAC address for interface 0/0
*Sep 22 11:20:34.570: %PA-3-PA_INIT_FAILED: Performance Agent failed to initialize
(Missing Data License)
*Sep 22 11:20:38.989: %PNP-6-PNP_DISCOVERY_STARTED: PnP Discovery started
*Sep 22 11:20:39.118: %LINK-3-UPDOWN: Interface GigabitEthernet0/0, changed state
to up
to up
to up
to up
to up
to up
to down
to down
*Sep 22 11:20:40.121: %LINEPROTO-5-UPDOWN: Line protocol on Interface
GigabitEthernet0/0, changed state to up
GigabitEthernet0/6, changed state to down
*Sep 22 11:20:40.837: %SYS-5-CONFIG_I: Configured from memory by console
*Sep 22 11:20:41.622: %SYS-5-RESTART: System restarted --
Cisco IOS Software, IOSv Software (VIOS-ADVENTERPRISEK9-M), Version 15.9(3)M3,
RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2021 by Cisco Systems, Inc.
Compiled Wed 27-Jan-21 09:58 by prod_rel_team
*Sep 22 11:20:41.626: %CVAC-4-FILE_IGNORED: Configuration file
flash0:/ios_config.txt is ignored : empty file
*Sep 22 11:20:41.659: %CVAC-4-FILE_IGNORED: Configuration file
flash2:/ios_config.txt is ignored : empty file
*Sep 22 11:20:41.767: %CRYPTO-6-ISAKMP_ON_OFF: ISAKMP is OFF
*Sep 22 11:20:41.768: %CRYPTO-6-GDOI_ON_OFF: GDOI is OFF
*Sep 22 11:20:42.341: %LINK-5-CHANGED: Interface GigabitEthernet0/0, changed state
to administratively down
*Sep 22 11:20:47.620: %PNP-6-PNP_BEST_UDI_UPDATE: Best UDI
[PID:IOSv,VID:1.0,SN:96NU8C5VZLMTGTUN16DNO] identified via (entity-mibs)
*Sep 22 11:20:47.620: %PNP-6-PNP_CDP_UPDATE: Device UDI
[PID:IOSv,VID:1.0,SN:96NU8C5VZLMTGTUN16DNO] identified for CDP
*Sep 22 11:20:47.623: %PNP-6-PNP_DISCOVERY_STOPPED: PnP Discovery stopped (Startup
Config Present)
*Sep 22 11:21:30.099: %PLATFORM-5-SIGNATURE_VERIFIED: Image 'flash0:/vios-
adventerprisek9-m' passed code signing verification
**************************************************************************
* IOSv is strictly limited to use for evaluation, demonstration and IOS *
* education. IOSv is provided as-is and is not supported by Cisco's *
* Technical Advisory Center. Any use or disclosure, in whole or in part, *
* of the IOSv Software or Documentation to any third party for any *
* purposes is expressly prohibited except as otherwise authorized by *
* Cisco in writing. *
**************************************************************************
R2#sh run
Building configuration...
Current configuration : 3555 bytes

!
version 15.9
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname R2
!
boot-start-marker
boot-end-marker
!
!
!
no aaa new-model
!
!
!
mmi polling-interval 60
no mmi auto-configure
no mmi pvc
mmi snmp-timeout 180
!
!
!
!
!
no ip icmp rate-limit unreachable
!
!
!
!
!
!
no ip domain lookup
ip cef
no ipv6 cef
!
multilink bundle-name authenticated
!
!
!
!
!
redundancy
!
no cdp log mismatch duplex
!
ip tcp synwait-time 5
!
!
!
!
!
!
!
!
!
!
!
!
!
interface GigabitEthernet0/0
no ip address
shutdown
duplex auto
speed auto
media-type rj45
!
no ip address
shutdown
duplex auto
speed auto
media-type rj45
!
ip address 10.10.1.2 255.255.255.0
duplex auto
speed auto
media-type rj45
!
no ip address
shutdown
duplex auto
speed auto
media-type rj45
!
no ip address
shutdown
duplex auto
speed auto
media-type rj45
!
no ip address
shutdown
duplex auto
speed auto
media-type rj45
!
no ip address
shutdown
duplex auto
speed auto
media-type rj45
!
no ip address
shutdown
duplex auto
speed auto
media-type rj45
!
!
router eigrp 100
network 10.10.0.0 0.0.255.255
!
ip forward-protocol nd
!
!
no ip http server
no ip http secure-server
!
ipv6 ioam timestamp
!
!
!
control-plane
!
banner exec ^C
**************************************************************************
**************************************************************************^C
banner incoming ^C
**************************************************************************
**************************************************************************^C
banner login ^C
**************************************************************************
**************************************************************************^C
!
line con 0
exec-timeout 0 0
privilege level 15
logging synchronous
line aux 0
exec-timeout 0 0
privilege level 15
logging synchronous
line vty 0 4
password ine
login
transport input telnet
!
no scheduler allocate
!
end
R2#

R2

Uploaded by

Copyright:

Available Formats

R2

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

R2

Uploaded by

Copyright:

Available Formats

Booting `IOSv: flash0:vios-adventerprisek9-m (hd0,msdos1)'

Booted IOSv. Boot args: [/vios-adventerprisek9-m]

Smart Init is enabled

Restricted Rights Legend

Use, duplication, or disclosure by the Government is

cisco Systems, Inc.

Cisco IOS Software, IOSv Software (VIOS-ADVENTERPRISEK9-M), Version 15.9(3)M3,

This product contains cryptographic features and is subject to United

If you require further assistance please contact us by sending email to

Cisco IOSv (revision 1.0) with with 410857K/111616K bytes of memory.Installed

Processor board ID 96NU8C5VZLMTGTUN16DNO

*Mar 1 00:00:00.921: %ATA-6-DEV_FOUND: device 0x1F0

Current configuration : 3555 bytes

You might also like