80W Single Output Switching Power Supply HLG- 80 H series

B auart gepruft

IP65 IP67
S ic herheit

egelma g e
od o s
be wac g

www. tuv .c om
ID 2000 0000 00

SPECIFICATION
MODEL HLG-80H-24
HLG-80H-24 HLG-80H-48
HLG-80H-48 HLG-80H-54
HLG-80H-54
DC VOLTAGE 24V 48V 54V
CONSTANT CURRENT REGION Note.4 14.4 ~ 24V 28.8 ~ 48V 32.4 ~ 54V
RATED CURRENT 3.4A 1.7A 1.5A
RATED POWER 81.6W 81.6W 81W
RIPPLE & NOISE (max.) Note.2 150mVp-p 200mVp-p 200mVp-p
VOLTAGE ADJ. RANGE Note.6 22 ~ 27V 43 ~ 53V 49 ~ 58V
OUTPUT Can be adjusted by internal potentiometer A type only
CURRENT ADJ. RANGE
2.04 ~ 3.4A 1.02 ~ 1.7A 0.9 ~ 1.5A
VOLTAGE TOLERANCE Note.3 ±1.0% ±1.0% ±1.0%
LINE REGULATION ±0.5% ±0.5% ±0.5%
LOAD REGULATION ±0.5% ±0.5% ±0.5%
SETUP, RISE TIME Note.8 1200ms,80ms/115VAC 500ms,80ms/230VAC at full load; B type 1200ms,200ms/115VAC 500ms,200ms/230VAC at 95% load
HOLD UP TIME (Typ.) 16ms at full load 230VAC /115VAC
VOLTAGE RANGE Note.5 90 ~ 305VAC 127 ~ 431VDC
FREQUENCY RANGE 47 ~ 63Hz
POWER FACTOR (Typ.) PF>0.96/115VAC, PF>0.96/230VAC, PF>0.94/277VAC at full load (Please refer to "Power Factor Characteristic" curve)
TOTAL HARMONIC DISTORTION THD< 20% when output loading≧60% at 115VAC/230VAC input and output loading≧75% at 277VAC input
EFFICIENCY (Typ.) 90.5% 91% 91%
INPUT
AC CURRENT (Typ.) 0.85A / 115VAC 0.425A / 230VAC 0.4A / 277VAC
INRUSH CURRENT (Typ.) COLD START 70A(twidth=485μs measured at 50% Ipeak) at 230VAC
MAX. No. of PSUs on 16A
3 units (circuit breaker of type B) / 6 units (circuit breaker of type C) at 230VAC
CIRCUIT BREAKER
LEAKAGE CURRENT <0.75mA / 277VAC
95 ~ 108%
OVER CURRENT Note.4
Protection type: Constant current limiting, recovers automatically after fault condition is removed
SHORT CIRCUIT Hiccup mode, recovers automatically after fault condition is removed
PROTECTION
28 ~ 35V 54 ~ 63V 59 ~ 68V
OVER VOLTAGE
Protection type: Shut down o/p voltage, re-power on to recover
OVER TEMPERATURE Shut down o/p voltage, re-power on to recover
WORKING TEMP. -40 ~ +70℃ (Refer to "Derating Curve")
WORKING HUMIDITY 20 ~ 95% RH non-condensing
ENVIRONMENT STORAGE TEMP., HUMIDITY -40 ~ +80℃, 10 ~ 95% RH
TEMP. COEFFICIENT ±0.03%/℃ (0 ~ 60℃)
VIBRATION 10 ~ 500Hz, 5G 12min./1cycle, period for 72min. each along X, Y, Z axes
UL8750, CSA C22.2 No. 250.0-08(except for HLG-80H-48/54V & HLG-80H-48/54BL), UL8750 listed for HLG-80H-□BL, EN61347-1,
SAFETY STANDARDS Note.7
EN61347-2-13 independent, optional models for J61347-1, J61347-2-13, IP65 or IP67 approved; Design refer to UL60950-1, TUV EN60950-1
SAFETY & WITHSTAND VOLTAGE I/P-O/P:3.75KVAC I/P-FG:2KVAC O/P-FG:1.5KVAC
EMC ISOLATION RESISTANCE I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25℃/ 70% RH
EMC EMISSION Compliance to EN55015, EN61000-3-2 Class C (≧60% load) ; EN61000-3-3
EMC IMMUNITY Compliance to EN61000-4-2,3,4,5,6,8,11, EN61547, EN55024, light industry level (surge 4KV), criteria A
MTBF 357.8K hrs min. MIL-HDBK-217F (25℃)
OTHERS DIMENSION 195.6*61.5*38.8mm (L*W*H)
PACKING 0.84Kg; 16pcs/14.4Kg/0.54CUFT
℃
NOTE

File Name:HLG-80H-SPEC 2017-11

 80W Single Output Switching Power Supply HLG- 80 H series

Mechanical Specification Case No.997A Unit:mm

Blank:(HLG-80H)
195.6
12 171.8
9.6

300±20 300±20
AC/L(Brown) T case +V(Red)
85.9

61.5
46.5
AC/N(Blue)
32
-V(Black)
FG (Green/Yellow) SJTW 18AWG×3C SVT 18AWG×2C

30.75
ψ4.2×4PL

※ T case: Max. Case Temperature.

38.8
※ IP67 rated. Cable for I/O connection.

A Type:(HLG-80H-_A)
195.6
12 171.8
9.6

300±20 300±20
AC/L(Brown) T case +V(Red)
85.9
61.5
46.5

AC/N(Blue)
32

-V(Black)
FG (Green/Yellow) SJTW 18AWG×3C SVT 18AWG×2C
30.75

Io Vo
ADJ. ADJ.
ψ4.2×4PL

※ T case: Max. Case Temperature.

38.8

※ IP65 rated. Output voltage and constant current level can be adjusted through internal potentiometer. (Can
access by removing the rubber stopper on the case.)

B Type:(HLG-80H-_B)
195.6
12 171.8
9.6
300±20
300±20 +V(Red)
AC/L(Brown) T case -V(Black)
85.9
61.5
46.5

AC/N(Blue) SVT 18AWG×2C

32

DIM+(Blue)
FG (Green/Yellow) SJTW 18AWG×3C
30.75

DIM-(White)
UL2517 18AWG×2C
ψ4.2×4PL

※ T case: Max. Case Temperature.

38.8

File Name:HLG-80H-SPEC 2017-11

 80W Single Output Switching Power Supply HLG- 80 H series

D Type(option):(HLG-80H-_D)

195.6
12 171.8
9.6

300±20 300±20
AC/L(Brown) T case 85.9 +V(Red)
61.5
46.5
AC/N(Blue)
32

-V(Black)
FG (Green/Yellow) SJTW 18AWG×3C SVT 18AWG×2C

30.75
ψ4.2×4PL

※ T case: Max. Case Temperature.

38.8
※ IP67 rated. Timer dimming function, contact MEAN WELL for details.

Block Diagram
Fosc : 100KHz

EMI FILTER PFC POWER RECTIFIERS +V

I/P & SWITCHING &
CIRCUIT -V
RECTIFIERS FILTER
O.L.P. DIM+
DIM-
(B Type)
FG O.T.P. O.L.P. DETECTION
PWM & PFC CIRCUIT
CONTROL
O.V.P.

Derating Curve Static Characteristics

100
100
90
80
230VAC 80
Input only
60 70
LOAD (%)

60
LOAD (%)

40
50
20
40

-40 -25 -10 0 15 30 50 60 70 (HORIZONTAL)

90 100 125 135 145 155 165 175 180 200 230 305

AMBIENT TEMPERATURE (℃) INPUT VOLTAGE (V) 60Hz

File Name:HLG-80H-SPEC 2017-11

 80W Single Output Switching Power Supply HLG- 80 H series

Power Factor Characteristic

Constant Current Mode

1 .0 0
0 .9 8
0 .9 6
0 .9 4
0 .9 2
0 .9 0 277Vac
PF

0 .8 8 230Vac
0 .8 6 1 1 5 V ac
0 .8 4
0 .8 2
0 .8 0
0 .7 8
50% 60% 70% 80% 90% 100%
(80W)

LOAD

EFFICIENCY vs LOAD (48V Model)

HLG-80H series possess superior working efficiency that up to 91% can be reached in field applications.

92

88

84
EFFICIENCY (%)

80 277Vac

76 230Vac
115Vac
72

68

64
10% 20% 30% 40% 50% 60% 70% 80% 90% 100%
LOAD

DRIVING METHODS OF LED MODULE

There are two major kinds of LED drive method "direct drive" and "with LED driver".
A typical LED power supply may either work in "constant voltage mode (CV) or constant current mode (CC)" to drive the LEDs.
Mean Well's LED power supply with CV+ CC characteristic can be operated at both CV mode [with LED driver, at area (A)] and CC mode [direct drive, at area (B)].

In the constant current region, the highest voltage at the output of the driver
100
depends on the configuration of the end systems.
Should there be any compatibility issues, please contact MEAN WELL.
(A) Constant (B)
Constant
Vo(%)

Voltage area
Current area

60
(min.)

(C)
Hiccup
Protection

50 100 Io (%)

Typical LED power supply I-V curve

File Name:HLG-80H-SPEC 2017-11

 80W Single Output Switching Power Supply HLG- 80 H series

DIMMING OPERATION

+V(Red)
AC/L(Brown) -V(Black)
AC/N(Blue) HLG-80H
DIM+(Blue)
FG (Green/Yellow)
DIM-(White)

※ Built-in 3 in 1 dimming function, IP67 rated. Output constant current level can be adjusted through output cable by connecting a resistance or 1 ~ 10Vdc
or 10V PWM signal between DIM+ and DIM-.
※ Please DO NOT connect "DIM-" to "-V".
※ Reference resistance value for output current adjustment (Typical)
Single driver 10KΩ 20KΩ 30KΩ 40KΩ 50KΩ 60KΩ 70KΩ 80KΩ 90KΩ 100KΩ OPEN
Resistance
value Multiple drivers
(N=driver quantity for synchronized
dimming operation)
10KΩ/N 20KΩ/N 30KΩ/N 40KΩ/N 50KΩ/N 60KΩ/N 70KΩ/N 80KΩ/N 90KΩ/N 100KΩ/N -----
Percentage of rated current 10% 20% 30% 40% 50% 60% 70% 80% 90% 100% 102%~108%
※ 1 ~ 10V dimming function for output current adjustment (Typical)
Dimming value 1V 2V 3V 4V 5V 6V 7V 8V 9V 10V OPEN
Percentage of rated current 10% 20% 30% 40% 50% 60% 70% 80% 90% 100% 102%~108%
※ 10V PWM signal for output current adjustment (Typical): Frequency range :100Hz ~ 3KHz
Duty value 10% 20% 30% 40% 50% 60% 70% 80% 90% 100% OPEN
Percentage of rated current 10% 20% 30% 40% 50% 60% 70% 80% 90% 100% 102%~108%

※Using the built-in dimming function on B-type model can't turn the lighting fixture totally dark. Please refer to the connection method below to achieve 0%
brightness of the lighting fixture connecting to the LED power supply unit.
※Direct connecting to LEDs is suggested, but is not suitable for using additional drivers.
Dimming connection diagram for turning the lighting fixture ON/OFF :

N FG L

Relay Switch Adjuster

10K~100K Ohms resistance

1~10V DC Voltage
10V PWM Signal

Blue
Green/ DIM+
White
Yellow AC/L HLG-80H DIM-
Brown Black
B Type V(-) LED Lighting Fixture
Red
AC/N V(+)
Blue

Using a switch and relay can turn ON/OFF the lighting fixture.
1.Output constant current level can be adjusted through output cable by connecting a resistance or 1~10Vdc or 10V PWM signal between DIM+ and DIM-. 2.The
LED lighting fixture can be turned ON/OFF by the switch.

File Name:HLG-80H-SPEC 2017-11

 80W Single Output Switching Power Supply HLG- 80 H series

WATERPROOF CONNECTION
◎ Waterproof connector
Waterproof connector can be assembled on the output cable of HLG-80H to operate in dry/wet/damp or outdoor environment.

AC
HLG-80H
source I/P O/P

Size Pin Configuration (Female) Size Pin Configuration (Female)

M12 M15
4-PIN 5-PIN 2-PIN
5A/PIN 5A/PIN 12A/PIN
Order No. M12-04 M12-05 Order No. M15-02
Suitable Current 10A max. 10A max. Suitable Current 12A max. LED Lamp

◎ Cable Joiner
CJ04-1 suitable for 14AWG~16AWG
66
CJ04-2 suitable for 18AWG~22AWG
26 20
ψ25

Up to four wires can be connected through this cable joiner by

soldering or clamping by tools.

LED Lamp

HLG-80H
O/P Wires

※CJ04 cable joiner can be purchased independently for user's own assembly.
MEAN WELL order No. : CJ04-1, CJ04-2.

◎ Junction Box(Option )
171.8 76 10
334 5
8.5 32 8.5 6

AC/L(Brown) +V(Red)
61.5

61

AC/N(Blue) -V(Black)
FG (Green/Yellow)
SVT 18AWG×2C
SJTW 18AWG×3C

2-ψ5

3- PF 1/2" 3- PF 1/2"
150±20 150±20
38.8
35

※Optional junction box available for A / Blank - type, please contact MEAW WELL for details. 86
※HLG-80H- BL models with junction box at both input and output side are listed(modified by B type only).
File Name:HLG-80H-SPEC 2017-11