INTERNATIONAL ISO

STANDARD 10898

Second edition
2016-09-15

Spot drills
Forets à pointer

iTeh STANDARD PREVIEW

(standards.iteh.ai)
ISO 10898:2016
https://standards.iteh.ai/catalog/standards/sist/f7d491e8-e348-47b8-825a-
4de83e543631/iso-10898-2016

Reference number
ISO 10898:2016(E)

© ISO 2016
ISO 10898:2016(E)


iTeh STANDARD PREVIEW

(standards.iteh.ai)
ISO 10898:2016
https://standards.iteh.ai/catalog/standards/sist/f7d491e8-e348-47b8-825a-
4de83e543631/iso-10898-2016

COPYRIGHT PROTECTED DOCUMENT

© ISO 2016, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org

ii  © ISO 2016 – All rights reserved

 ISO 10898:2016(E)


Contents Page

Foreword......................................................................................................................................................................................................................................... iv
1 Scope.................................................................................................................................................................................................................................. 1
2 Normative references....................................................................................................................................................................................... 1
3 Dimensions.................................................................................................................................................................................................................. 1
4 Technical specifications................................................................................................................................................................................. 1
4.1 Conception................................................................................................................................................................................................... 1
4.2 Permissible division deviation on flutes............................................................................................................................ 1
4.3 Maximum runout of the fluted part with respect to the shank...................................................................... 1
5 Designation................................................................................................................................................................................................................. 1
Annex A (informative) Relationship between designations of this International Standard
and ISO 13399.......................................................................................................................................................................................................... 3
Bibliography................................................................................................................................................................................................................................. 4

iTeh STANDARD PREVIEW

(standards.iteh.ai)
ISO 10898:2016
https://standards.iteh.ai/catalog/standards/sist/f7d491e8-e348-47b8-825a-
4de83e543631/iso-10898-2016

© ISO 2016 – All rights reserved  iii

ISO 10898:2016(E)


Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment,
as well as information about ISO’s adherence to the World Trade Organization (WTO) principles in the
iTeh STANDARD PREVIEW
Technical Barriers to Trade (TBT) see the following URL: www.iso.org/iso/foreword.html.
(standards.iteh.ai)
The committee responsible for this document is ISO/TC 29, Small tools, Subcommittee SC 9, Tools with
defined cutting edges, cutting items.
ISO 10898:2016
This second edition cancels and replaces the first edition (ISO 10898:1992), of which it constitutes a
https://standards.iteh.ai/catalog/standards/sist/f7d491e8-e348-47b8-825a-
minor revision with the following changes:4de83e543631/iso-10898-2016
— Annex A has been added;
— a Bibliography has been added.

iv  © ISO 2016 – All rights reserved

INTERNATIONAL STANDARD ISO 10898:2016(E)

Spot drills

1 Scope
This International Standard specifies the dimensions and technical specifications of spot drills of high-
speed steel and hardmetal with a point angle of 90° or 120°.

2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
ISO 286-2, Geometrical product specifications (GPS) — ISO code system for tolerances on linear sizes —
Part 2: Tables of standard tolerance classes and limit deviations for holes and shafts

3 Dimensions
See Figure 1 and Table 1.
iTeh STANDARD PREVIEW
4 Technical specifications
(standards.iteh.ai)
4.1 Conception ISO 10898:2016
https://standards.iteh.ai/catalog/standards/sist/f7d491e8-e348-47b8-825a-
Spot drills in accordance with this International Standard shall be made without lands and back taper.
4de83e543631/iso-10898-2016

4.2 Permissible division deviation on flutes

See Table 2.

4.3 Maximum runout of the fluted part with respect to the shank
See Table 2.

5 Designation
Spot drills in accordance with this International Standard shall be designated by the following:
a) “Spot drill”;
b) a reference to this International Standard;
c) its point angle;
d) its diameter, d, in millimetres.
EXAMPLE A spot drill of diameter d = 10 mm and point angle 90° is designated as follows:

      Spot drill ISO 10898 - 90° - 10

© ISO 2016 – All rights reserved  1

ISO 10898:2016(E)


Figure 1

Table 1
Dimensions in millimetres
d h8a 4 6 8 10 12 16 20
L 52 66 79 89 102 115 131
l 12 20 25 25 30 35 40
a See ISO 286-2.

Table 2
Dimensions in millimetres
Permissible division deviation on Maximum runout of the fluted part
d
flutes
iTeh STANDARD PREVIEW with respect to the shank
4; 6 0,03 0,03
8; 10 (standards.iteh.ai)
0,04 0,04
12; 16; 20 0,05 0,05
ISO 10898:2016
https://standards.iteh.ai/catalog/standards/sist/f7d491e8-e348-47b8-825a-
4de83e543631/iso-10898-2016

2  © ISO 2016 – All rights reserved

 ISO 10898:2016(E)


Annex A
(informative)

Relationship between designations of this International Standard

and ISO 13399

For the relationship between the designations of this International Standard and preferred symbols
according to ISO 13399, see Table A.1.

Table A.1 — Relationship between designations of this International Standard and ISO 13399
Symbol in this Reference in this
Property name in Symbol in the Reference in the
International International
the ISO 13399 series ISO 13399 series ISO 13399 series
Standard Standard
Figure 1
d Cutting diameter DC 71D084653E57F
Table 1
Figure 1
L Overall length OAL 71D078EB7C086
Table 1
Figure 1
l Length chip flute LCF 71DCCC27DEF53
Table 1
—
iTeh STANDARD
Clause 5
PREVIEW
Point angle SIG 71DCCC4FEF366

— —
(standards.iteh.ai)
Connection diameter
DCONMS a 71EBDBF5060E6
machine side
a DCONMS has the same size as d (DC) in Figure 1. 10898:2016
ISO
https://standards.iteh.ai/catalog/standards/sist/f7d491e8-e348-47b8-825a-
4de83e543631/iso-10898-2016

© ISO 2016 – All rights reserved  3

ISO 10898:2016(E)


Bibliography

[1] ISO 13399 (all parts), Cutting tool data representation and exchange

iTeh STANDARD PREVIEW

(standards.iteh.ai)
ISO 10898:2016
https://standards.iteh.ai/catalog/standards/sist/f7d491e8-e348-47b8-825a-
4de83e543631/iso-10898-2016

4  © ISO 2016 – All rights reserved

 iTeh STANDARD PREVIEW
(standards.iteh.ai)
ISO 10898:2016
https://standards.iteh.ai/catalog/standards/sist/f7d491e8-e348-47b8-825a-
4de83e543631/iso-10898-2016