Product Name: MOBILUX EP 2

Revision Date: 28 Jul 2021

Page 1 of 9

SAFETY DATA SHEET

SECTION 1 PRODUCT AND COMPANY IDENTIFICATION

PRODUCT
Product Name: MOBILUX EP 2
Product Description: Base Oil and Additives
Product Code: 2015A0208050, 641274-00, 970717
Intended Use: Grease

COMPANY IDENTIFICATION
Supplier: EXXON MOBIL CORPORATION
22777 Springwoods Village Parkway
Spring, TX. 77253 USA
24 Hour Health Emergency 609-737-4411
Transportation Emergency Phone 800-424-9300 or 703-527-3887 CHEMTREC
Product Technical Information 800-662-4525
MSDS Internet Address http://www.exxon.com, http://www.mobil.com

SECTION 2 HAZARDS IDENTIFICATION

This material is not hazardous according to regulatory guidelines (see (M)SDS Section 15).

Other hazard information:

HAZARD NOT OTHERWISE CLASSIFIED (HNOC): None as defined under 29 CFR 1910.1200.

PHYSICAL / CHEMICAL HAZARDS

No significant hazards.

HEALTH HAZARDS
High-pressure injection under skin may cause serious damage. Excessive exposure may result in eye, skin, or
respiratory irritation.

ENVIRONMENTAL HAZARDS
No significant hazards.

NFPA Hazard ID: Health: 0 Flammability: 1 Reactivity: 0

HMIS Hazard ID: Health: 0 Flammability: 1 Reactivity: 0

NOTE: This material should not be used for any other purpose than the intended use in Section 1 without expert advice. Health
studies have shown that chemical exposure may cause potential human health risks which may vary from person to person.
 Product Name: MOBILUX EP 2
Revision Date: 28 Jul 2021
Page 2 of 9

SECTION 3 COMPOSITION / INFORMATION ON INGREDIENTS

This material is defined as a mixture.

Hazardous Substance(s) or Complex Substance(s) required for disclosure

Name CAS# Concentration* GHS Hazard Codes
PHOSPHORIC ACID ESTERS, AMINE SALT 61188-14-5 0.1 - < 1% H318, H401, H411
ZINC DITHIOPHOSPHATE 68649-42-3 1 - < 2.5% H315, H318, H401, H411

* All concentrations are percent by weight unless material is a gas. Gas concentrations are in percent by volume.

As per paragraph (i) of 29 CFR 1910.1200, formulation is considered a trade secret and specific chemical identity and exact
percentage (concentration) of composition may have been withheld. Specific chemical identity and exact percentage composition
will be provided to health professionals, employees, or designated representatives in accordance with applicable provisions of
paragraph (i).

SECTION 4 FIRST AID MEASURES

INHALATION
Under normal conditions of intended use, this material is not expected to be an inhalation hazard.

SKIN CONTACT
Wash contact areas with soap and water. If product is injected into or under the skin, or into any part of the body,
regardless of the appearance of the wound or its size, the individual should be evaluated immediately by a physician as a
surgical emergency. Even though initial symptoms from high pressure injection may be minimal or absent, early surgical
treatment within the first few hours may significantly reduce the ultimate extent of injury.

EYE CONTACT
Flush thoroughly with water. If irritation occurs, get medical assistance.

INGESTION
First aid is normally not required. Seek medical attention if discomfort occurs.

SECTION 5 FIRE FIGHTING MEASURES

EXTINGUISHING MEDIA
Appropriate Extinguishing Media: Use water fog, foam, dry chemical or carbon dioxide (CO2) to extinguish flames.

Inappropriate Extinguishing Media: Straight Streams of Water

FIRE FIGHTING
Fire Fighting Instructions: Evacuate area. Prevent runoff from fire control or dilution from entering streams, sewers,
or drinking water supply. Firefighters should use standard protective equipment and in enclosed spaces, self-contained
breathing apparatus (SCBA). Use water spray to cool fire exposed surfaces and to protect personnel.

Hazardous Combustion Products: Aldehydes, Incomplete combustion products, Oxides of carbon, Smoke, Fume,
Sulfur oxides
 Product Name: MOBILUX EP 2
Revision Date: 28 Jul 2021
Page 3 of 9

FLAMMABILITY PROPERTIES
Flash Point [Method]: >204°C (400°F) [EST. FOR OIL, ASTM D-92 (COC)]
Flammable Limits (Approximate volume % in air): LEL: N/D UEL: N/D
Autoignition Temperature: N/D

SECTION 6 ACCIDENTAL RELEASE MEASURES

NOTIFICATION PROCEDURES
In the event of a spill or accidental release, notify relevant authorities in accordance with all applicable regulations. US
regulations require reporting releases of this material to the environment which exceed the applicable reportable quantity
or oil spills which could reach any waterway including intermittent dry creeks. The National Response Center can be
reached at (800)424-8802.

PROTECTIVE MEASURES
Avoid contact with spilled material. See Section 5 for fire fighting information. See the Hazard Identification Section
for Significant Hazards. See Section 4 for First Aid Advice. See Section 8 for advice on the minimum requirements for
personal protective equipment. Additional protective measures may be necessary, depending on the specific circumstances
and/or the expert judgment of the emergency responders.

For emergency responders: Respiratory protection: respiratory protection will be necessary only in special cases, e.g.,
formation of mists. Half-face or full-face respirator with filter(s) for dust/organic vapor or Self Contained Breathing
Apparatus (SCBA) can be used depending on the size of spill and potential level of exposure. If the exposure cannot be
completely characterized or an oxygen deficient atmosphere is possible or anticipated, SCBA is recommended. Work
gloves that are resistant to hydrocarbons are recommended. Gloves made of polyvinyl acetate (PVA) are not water-
resistant and are not suitable for emergency use. Chemical goggles are recommended if splashes or contact with eyes is
possible. Small spills: normal antistatic work clothes are usually adequate. Large spills: full body suit of chemical
resistant, antistatic material is recommended.

SPILL MANAGEMENT
Land Spill: Allow spilled material to solidify and scrape up with shovels into a suitable container for recycle or disposal.
Scrape up spilled material with shovels into a suitable container for recycle or disposal.

Water Spill: Stop leak if you can do it without risk. Confine the spill immediately with booms. Warn other shipping.
Skim from surface.

Water spill and land spill recommendations are based on the most likely spill scenario for this material; however,
geographic conditions, wind, temperature, (and in the case of a water spill) wave and current direction and speed may
greatly influence the appropriate action to be taken. For this reason, local experts should be consulted. Note: Local
regulations may prescribe or limit action to be taken.

ENVIRONMENTAL PRECAUTIONS
Prevent entry into waterways, sewers, basements or confined areas.

SECTION 7 HANDLING AND STORAGE

HANDLING
Prevent small spills and leakage to avoid slip hazard.

Static Accumulator: This material is not a static accumulator.

 Product Name: MOBILUX EP 2
Revision Date: 28 Jul 2021
Page 4 of 9

STORAGE
Do not store in open or unlabelled containers.

SECTION 8 EXPOSURE CONTROLS / PERSONAL PROTECTION

NOTE: Limits/standards shown for guidance only. Follow applicable regulations.

No biological limits allocated.

ENGINEERING CONTROLS

The level of protection and types of controls necessary will vary depending upon potential exposure conditions. Control
measures to consider:
No special requirements under ordinary conditions of use and with adequate ventilation.

PERSONAL PROTECTION

Personal protective equipment selections vary based on potential exposure conditions such as applications, handling
practices, concentration and ventilation. Information on the selection of protective equipment for use with this material,
as provided below, is based upon intended, normal usage.

Respiratory Protection: If engineering controls do not maintain airborne contaminant concentrations at a level which
is adequate to protect worker health, an approved respirator may be appropriate. Respirator selection, use, and
maintenance must be in accordance with regulatory requirements, if applicable. Types of respirators to be considered for
this material include:
No protection is ordinarily required under normal conditions of use and with adequate ventilation.

For high airborne concentrations, use an approved supplied-air respirator, operated in positive pressure mode. Supplied
air respirators with an escape bottle may be appropriate when oxygen levels are inadequate, gas/vapor warning properties
are poor, or if air purifying filter capacity/rating may be exceeded.

Hand Protection: Any specific glove information provided is based on published literature and glove manufacturer
data. Glove suitability and breakthrough time will differ depending on the specific use conditions. Contact the glove
manufacturer for specific advice on glove selection and breakthrough times for your use conditions. Inspect and replace
worn or damaged gloves. The types of gloves to be considered for this material include:
No protection is ordinarily required under normal conditions of use.

Eye Protection: If contact is likely, safety glasses with side shields are recommended.

Skin and Body Protection: Any specific clothing information provided is based on published literature or
manufacturer data. The types of clothing to be considered for this material include:
No skin protection is ordinarily required under normal conditions of use. In accordance with good industrial
hygiene practices, precautions should be taken to avoid skin contact.

Specific Hygiene Measures: Always observe good personal hygiene measures, such as washing after handling the
material and before eating, drinking, and/or smoking. Routinely wash work clothing and protective equipment to remove
contaminants. Discard contaminated clothing and footwear that cannot be cleaned. Practice good housekeeping.
 Product Name: MOBILUX EP 2
Revision Date: 28 Jul 2021
Page 5 of 9

ENVIRONMENTAL CONTROLS
Comply with applicable environmental regulations limiting discharge to air, water and
soil. Protect the environment by applying appropriate control measures to prevent or limit
emissions.

SECTION 9 PHYSICAL AND CHEMICAL PROPERTIES

Note: Physical and chemical properties are provided for safety, health and environmental considerations only and may not
fully represent product specifications. Contact the Supplier for additional information.

GENERAL INFORMATION
Physical State: Solid
Form: Semi-fluid
Color: Brown
Odor: Characteristic
Odor Threshold: N/D

IMPORTANT HEALTH, SAFETY, AND ENVIRONMENTAL INFORMATION

Relative Density (at 15 °C): 0.92
Flammability (Solid, Gas):
Flash Point [Method]: >204°C (400°F) [EST. FOR OIL, ASTM D-92 (COC)]
Flammable Limits (Approximate volume % in air): LEL: N/D UEL: N/D
Autoignition Temperature: N/D
Boiling Point / Range: > 316°C (600°F)
Decomposition Temperature: N/D
Vapor Density (Air = 1): N/D
Vapor Pressure: < 0.013 kPa (0.1 mm Hg) at 20 °C
Evaporation Rate (n-butyl acetate = 1): N/D
pH: N/A
Log Pow (n-Octanol/Water Partition Coefficient): > 3.5
Solubility in Water: Negligible
Viscosity: 150 cSt (150 mm2/sec) at 40 °C
Oxidizing Properties: See Hazards Identification Section.

OTHER INFORMATION
Freezing Point: N/D
Melting Point: N/D
DMSO Extract (mineral oil only), IP-346: < 3 %wt

NOTE: Most physical properties above are for the oil component in the material.

SECTION 10 STABILITY AND REACTIVITY

REACTIVITY: See sub-sections below.

STABILITY: Material is stable under normal conditions.

CONDITIONS TO AVOID: Excessive heat. High energy sources of ignition.

 Product Name: MOBILUX EP 2
Revision Date: 28 Jul 2021
Page 6 of 9

MATERIALS TO AVOID: Strong oxidizers

HAZARDOUS DECOMPOSITION PRODUCTS: Material does not decompose at ambient temperatures.

POSSIBILITY OF HAZARDOUS REACTIONS: Hazardous polymerization will not occur.

SECTION 11 TOXICOLOGICAL INFORMATION

INFORMATION ON TOXICOLOGICAL EFFECTS

Hazard Class Conclusion / Remarks

Inhalation
Acute Toxicity: No end point data for material. Minimally Toxic. Based on assessment of the components.
Irritation: No end point data for material. Negligible hazard at ambient/normal handling temperatures.
Ingestion
Acute Toxicity: No end point data for material. Minimally Toxic. Based on assessment of the components.
Skin
Acute Toxicity: No end point data for material. Minimally Toxic. Based on assessment of the components.
Skin Corrosion/Irritation: No end point data for Negligible irritation to skin at ambient temperatures. Based on
material. assessment of the components.
Eye
Serious Eye Damage/Irritation: No end point May cause mild, short-lasting discomfort to eyes. Based on assessment
data for material. of the components.
Sensitization
Respiratory Sensitization: No end point data for Not expected to be a respiratory sensitizer.
material.
Skin Sensitization: No end point data for Not expected to be a skin sensitizer. Based on assessment of the
material. components.
Aspiration: Data available. Not expected to be an aspiration hazard. Based on physico-chemical
properties of the material.
Germ Cell Mutagenicity: No end point data for Not expected to be a germ cell mutagen. Based on assessment of the
material. components.
Carcinogenicity: No end point data for material. Not expected to cause cancer. Based on assessment of the components.
Reproductive Toxicity: No end point data for Not expected to be a reproductive toxicant. Based on assessment of the
material. components.
Lactation: No end point data for material. Not expected to cause harm to breast-fed children.
Specific Target Organ Toxicity (STOT)
Single Exposure: No end point data for material. Not expected to cause organ damage from a single exposure.
Repeated Exposure: No end point data for Not expected to cause organ damage from prolonged or repeated
material. exposure. Based on assessment of the components.

OTHER INFORMATION

Contains:
Base oil severely refined: Not carcinogenic in animal studies. Representative material passes IP-346, Modified Ames test, and/or
other screening tests. Dermal and inhalation studies showed minimal effects; lung non-specific infiltration of immune cells, oil
deposition and minimal granuloma formation. Not sensitizing in test animals.
 Product Name: MOBILUX EP 2
Revision Date: 28 Jul 2021
Page 7 of 9

The following ingredients are cited on the lists below: None.

--REGULATORY LISTS SEARCHED--

1 = NTP CARC 3 = IARC 1 5 = IARC 2B
2 = NTP SUS 4 = IARC 2A 6 = OSHA CARC

SECTION 12 ECOLOGICAL INFORMATION

The information given is based on data available for the material, the components of the material, and similar materials.

ECOTOXICITY
Material -- Not expected to be harmful to aquatic organisms.

MOBILITY
Base oil component -- Low solubility and floats and is expected to migrate from water to the land. Expected to
partition to sediment and wastewater solids.

PERSISTENCE AND DEGRADABILITY

Biodegradation:
Base oil component -- Expected to be inherently biodegradable

BIOACCUMULATION POTENTIAL
Base oil component -- Has the potential to bioaccumulate, however metabolism or physical properties may reduce
the bioconcentration or limit bioavailability.

SECTION 13 DISPOSAL CONSIDERATIONS

Disposal recommendations based on material as supplied. Disposal must be in accordance with current applicable laws and
regulations, and material characteristics at time of disposal.

DISPOSAL RECOMMENDATIONS
Product is suitable for burning in an enclosed controlled burner for fuel value or disposal by supervised incineration at
very high temperatures to prevent formation of undesirable combustion products.

REGULATORY DISPOSAL INFORMATION

RCRA Information: The unused product, in our opinion, is not specifically listed by the EPA as a hazardous waste (40
CFR, Part 261D), nor is it formulated to contain materials which are listed as hazardous wastes. It does not exhibit the
hazardous characteristics of ignitability, corrositivity or reactivity and is not formulated with contaminants as determined
by the Toxicity Characteristic Leaching Procedure (TCLP). However, used product may be regulated.

Empty Container Warning Empty Container Warning (where applicable): Empty containers may contain residue and can be
dangerous. Do not attempt to refill or clean containers without proper instructions. Empty drums should be completely drained
and safely stored until appropriately reconditioned or disposed. Empty containers should be taken for recycling, recovery, or
 Product Name: MOBILUX EP 2
Revision Date: 28 Jul 2021
Page 8 of 9

disposal through suitably qualified or licensed contractor and in accordance with governmental regulations. DO NOT
PRESSURISE, CUT, WELD, BRAZE, SOLDER, DRILL, GRIND, OR EXPOSE SUCH CONTAINERS TO HEAT, FLAME,
SPARKS, STATIC ELECTRICITY, OR OTHER SOURCES OF IGNITION. THEY MAY EXPLODE AND CAUSE INJURY
OR DEATH.

SECTION 14 TRANSPORT INFORMATION

LAND (DOT): Not Regulated for Land Transport

LAND (TDG): Not Regulated for Land Transport

SEA (IMDG): Not Regulated for Sea Transport according to IMDG-Code

Marine Pollutant: No

AIR (IATA): Not Regulated for Air Transport

SECTION 15 REGULATORY INFORMATION

OSHA HAZARD COMMUNICATION STANDARD: This material is not considered hazardous in accordance with
OSHA HazCom 2012, 29 CFR 1910.1200.

Listed or exempt from listing/notification on the following chemical inventories: AICS, DSL, IECSC, KECI,
PICCS, TSCA

EPCRA SECTION 302: This material contains no extremely hazardous substances.

SARA (311/312) REPORTABLE HAZARD CATEGORIES: None.

SARA (313) TOXIC RELEASE INVENTORY:

Chemical Name CAS Number Typical Value

ZINC DITHIOPHOSPHATE 68649-42-3 1 - < 2.5%

The following ingredients are cited on the lists below:

Chemical Name CAS Number List Citations

DIPHENYLAMINE 122-39-4 18
ZINC DITHIOPHOSPHATE 68649-42-3 13, 15, 17, 19

--REGULATORY LISTS SEARCHED--

1 = ACGIH ALL 6 = TSCA 5a2 11 = CA P65 REPRO 16 = MN RTK
 Product Name: MOBILUX EP 2
Revision Date: 28 Jul 2021
Page 9 of 9

2 = ACGIH A1 7 = TSCA 5e 12 = CA RTK 17 = NJ RTK

3 = ACGIH A2 8 = TSCA 6 13 = IL RTK 18 = PA RTK
4 = OSHA Z 9 = TSCA 12b 14 = LA RTK 19 = RI RTK
5 = TSCA 4 10 = CA P65 CARC 15 = MI 293

Code key: CARC=Carcinogen; REPRO=Reproductive

SECTION 16 OTHER INFORMATION

N/D = Not determined, N/A = Not applicable

KEY TO THE H-CODES CONTAINED IN SECTION 3 OF THIS DOCUMENT (for information only):
H315: Causes skin irritation; Skin Corr/Irritation, Cat 2
H318: Causes serious eye damage; Serious Eye Damage/Irr, Cat 1
H401: Toxic to aquatic life; Acute Env Tox, Cat 2
H411: Toxic to aquatic life with long lasting effects; Chronic Env Tox, Cat 2

THIS SAFETY DATA SHEET CONTAINS THE FOLLOWING REVISIONS:

Revision Changes:
Section 05: Hazardous Combustion Products information was modified.
Section 14: Marine Pollutant information was modified.
Section 16: Revision Information - Implementation of GHS requirements phrase. information was deleted.
Section 01: Company Mailing Address information was modified.
Composition: Component Table information was modified.
Section 15: SARA (313) TOXIC RELEASE INVENTORY - Table information was modified.
Section 05: Hazardous Combustion Products information was modified.

The information and recommendations contained herein are, to the best of ExxonMobil's knowledge and belief, accurate
and reliable as of the date issued. You can contact ExxonMobil to insure that this document is the most current
available from ExxonMobil. The information and recommendations are offered for the user's consideration and
examination. It is the user's responsibility to satisfy itself that the product is suitable for the intended use. If buyer
repackages this product, it is the user's responsibility to insure proper health, safety and other necessary information is
included with and/or on the container. Appropriate warnings and safe-handling procedures should be provided to
handlers and users. Alteration of this document is strictly prohibited. Except to the extent required by law, re-
publication or retransmission of this document, in whole or in part, is not permitted. The term, "ExxonMobil" is used for
convenience, and may include any one or more of ExxonMobil Chemical Company, Exxon Mobil Corporation, or any
affiliates in which they directly or indirectly hold any interest.

Internal Use Only

MHC: 0B, 0B, 0, 0, 0, 0 PPEC: A

DGN: 2009877XUS (539035)

Copyright 2002 Exxon Mobil Corporation, All rights reserved