Yamaha CDX E400

MINI COMPONENT SYSTEM CRX-E400
CDX-E400 SERVICE MANUAL

The CRX-E400 is composed of the
RX-E400 and the CDX-E400. This
service manual is for the CDX-E400.
For the RX-E400 service manual,
please refer to the following publication
number :
RX-E400 100809
For the system operation, please refer

to the service manual for the RX-E400.
IMPORTANT NOTICE
This manual has been provided for the use of authorized YAMAHA Retailers and their service personnel.
It has been assumed that basic service procedures inherant to the industry, and more specifically YAMAHA Products, are already
known and understood by the users, and have therefore not been restated.
WARNING: Failure to follow appropriate service and safety procedures when servicing this product may result in personal
injury, destruction of expensive components and failure of the product to perform as specified. For these reasons,
we advise all YAMAHA product owners that all service required should be performed by an authorized
YAMAHA Retailer or the appointed service representative.
IMPORTANT: The presentation or sale of this manual to any individual or firm does not constitute authorization, certification or
recognition of any applicable technical capabilities, or establish a principle-agent relationship of any form.
The data provided is believed to be accurate and applicable to the unit(s) indicated on the cover. The research, engineering, and
service departments of YAMAHA are continually striving to improve YAMAHA products. Modifications are, therefore, inevitable
and specifications are subject to change without notice or obligation to retrofit. Should any discrepancy appear to exist, please contact
the distributor's Service Division.
WARNING: Static discharges can destroy expensive components. Discharge any static electricity your body may have accumu-
lated by grounding yourself to the ground buss in the unit (heavy gauge black wires connect to this buss).
IMPORTANT: Turn the unit OFF during disassembly and parts replacement. Recheck all work before you apply power to the unit.
■ CONTENTS
CDX-E400
TO SERVICE PERSONNEL ..................................... 2–3 IC DATA ................................................................ 15–19
PREVENTION OF ELECTRO STATIC DISCHARGE ..... 4 DISPLAY DATA .......................................................... 20
REAR PANELS ............................................................. 4 BLOCK DIAGRAM ...................................................... 21
SPECIFICATIONS ......................................................... 5 PRINTED CIRCUIT BOARD ................................ 22–23
INTERNAL VIEW .......................................................... 5 IC BLOCK ................................................................... 24
DISASSEMBLY PROCEDURES .............................. 6–8 PIN CONNECTION DIAGRAM ................................... 24
STANDARD OPERATION CHART ........................ 9–10 SCHEMATIC DIAGRAM ............................................. 25
TEST MODE .......................................................... 11–12 PARTS LIST .......................................................... 27–34
ERROR MESSAGE ............................................... 13–14 PARTS LIST FOR CARBON RESISTORS ............... 35
100808
Downloaded from www.Manualslib.com manuals search engine

CDX-E400
■ TO SERVICE PERSONNEL
1. Critical Components Information AC LEAKAGE
Components having special characteristics are marked Z WALL EQUIPMENT TESTER OR
and must be replaced with parts having specifications equal OUTLET UNDER TEST EQUIVALENT
to those originally installed.
2. Leakage Current Measurement (For 120V Models Only)

When service has been completed, it is imperative to verify
that all exposed conductive surfaces are properly insulated
from supply circuits. INSULATING
TABLE
● Meter impedance should be equivalent to 1500 ohm shunted
by 0.15µF.
● Leakage current must not exceed 0.5mA.
● Be sure to test for leakage with the AC plug in both

polarities.
THIS PRODUCT SHOULD NOT BE ADJUSTED OR REPAIRED BY ANYONE EXCEPT PROPERLY QUALIFIED SERVICE
PERSONNEL.
WARNING: CHEMICAL CONTENT NOTICE!

The solder used in the production of this product contains LEAD. In addition, other electrical/electronic and/or
plastic (where applicable) components may also contain traces of chemicals found by the California Health and
Welfare Agency (and possibly other entities) to cause cancer and/or birth defects or other reproductive harm.
DO NOT PLACE SOLDER, ELECTRICAL/ELECTRONIC OR PLASTIC COMPONENTS IN YOUR MOUTH FOR
ANY REASON WHATSOEVER!
Avoid prolonged, unprotected contact between solder and your skin! When soldering, do not inhale solder fumes
or expose eyes to solder/flux vapor!
If you come in contact with solder or components located inside the enclosure of this product, wash your hands
before handling food.
WARNING: Laser Safety

This product contains a laser beam component. This component may emit invisible, as well as visible radiation,
which may cause eye damage. To protect your eyes and skin from laser radiation, the following precautions must
be used during servicing of the unit.
1) When testing and/or repairing any component within the product, keep your eyes and skin more than 30 cm away from
the laser pick-up unit at all times. Do not stare at the laser beam at any time.
2) Do not attempt to readjust, disassemble or repair the laser pick-up, unless noted elsewhere in this manual.
3) CAUTION : Use of controls, adjustments or performance of procedures other than those specified herein may result in
hazardous radiation exposure.
CDX-E400
Laser Emitting conditions:

1) When the Top Cover is removed, and the “STANDBY/ON” SW is turned to the "ON" position, the laser component will
emit a beam for several seconds to detect if a disc is present. During this time (5-10 sec.) the laser may radiate through
the lens of the laser pick-up unit. Do not attempt any servicing during this period!
If no disc is detected, the laser will stop emitting the beam. When a disc is set, you will not be exposed to any laser
emissions.
2) The laser power level can be adjusted with the VR on the pick-up PWB. However, this level has been set by the factory
prior to shipping from the factory. Do not adjust this laser level control unless instruction is provided elsewhere in this
manual. Adjustment of this control can increase the laser emission level from the device.
2
CDX-E400
Laser Diode Properties

● Material : GaAlAs Optical Pick-up
● Wavelength : 780 nm
● Emission Duration : Continuous
● Laser Output : max. 44.6 µW*
* This output is the value measured at a distance of about
200 mm from the objective lens surface on the Optical
Pick-up Block.
When checking the laser diode emission, keep your eyes more
than 30 cm away from the objective lens.
VARO! : AVATTAESSA JA SUOJALUKITUS OHITETTAESSA OLET ALTTIINA NÄKYMÄTTÖMÄLLE

LASER-SÄTEILYLLE. ÄLÄ KATSO SÄTEESEEN.
VARNING! : OSYNLIG LASERSTRÅLNING NÄR DENNA DEL ÄR ÖPPNAD OCH SPÄRREN ÄR URKOPPLAD.
BETRAKTA EJ STRÅLEN.
CDX-E400
3
CDX-E400
■ PREVENTION OF ELECTRO STATIC DISCHARGE

The laser diode in the CD mechanism unit (optical pickup) may be damaged due to static electricity from clothes or
the human body. Use caution to prevent electrostatic damage when servicing or handling the laser diode.
1. Grounding for electrostatic damage prevention

1. Worktable grounding
Put a grounded conductive material (sheet) or iron sheet on the area where the optical pickup is placed.
2. Human body grounding

Use an anti-static wrist strap to discharge the static electricity from your body.
Anti-static wrist strip

1MΩ
Conductive material
(sheet) or steel sheet
2. Handling of the optical pickup

Do not use a tester to check the laser diode in the optical pickup. The power supply in the tester will damage the
laser diode.
3. Handling Precautions for the CD mechanism Unit (Optical Pickup)

1. Handle the CD mechanism unit (optical pickup) gently, as it is an extremely high-precision assembly.
2. The flexible cable lines may break if an excessive force is applied to it. Use caution when handling the cable.
3. The semi-fixed resistor for laser power adjustment should not be adjusted. Do not turn the resistor.
■ REAR PANELS
▼ R model ▼ B model
SERIAL LABEL
SERIAL LABEL
CDX-E400
240V
▼ G model
4
CDX-E400
■ SPECIFICATIONS
Output Level ● DIMENSIONS
1kHz, 0dB 2.0 ± 0.5Vrms
Signal to Nosie Ratio (EIAJ) 102dB
Dynamic Range 95dB
Harmonic Distortion+Noise (1kHz) 0.004%
Frequency Response
2Hz — 20kHz ±0.5dB
Power Requirements
335(13-3/16")
346(13-5/8")
B, G models 230V AC 50Hz
R model 110/120/220/240V AC 50/60Hz
Power Consumption 10W
Dimensions (W x H x D) 217 x 108 x 346mm
(8-9/16" x 4-1/4" x 13-5/8")
Weight 3.0kg (6 lbs 9 oz)
Finish
Gold color R, G models
Silver color G, B models
*Specifications are subject to change without notice.
100(3-15/16")
108(4-1/4")
B .................... British model
G ............... European model
R .................. General model
(5/16")
217(8-9/16")
8
Unit : mm (inch)
■ INTERNAL VIEW
q w e
q MAIN (3) P.C.B.

w MAIN (4) P.C.B. (R model only)
CDX-E400
e MAIN (1) P.C.B.
r CD MECHANISM UNIT
t MAIN (2) P.C.B.
r t
5
CDX-E400
■ DISASSEMBLY PROCEDURES (Remove parts in disassembly order as numbered.)
1. Removal of Top Cover

a. Remove 4 screws ( q ) and 4 screws ( w ) in Fig. 1.
b. Lift the Top Cover at the rear and move it rear-ward slantingly.
2. Removal of Front Panel
a. Remove a connector (CB102) in Fig. 2.
b. Remove 2 screws ( e ) and 2 screws ( r ) in Fig. 1.
c. Remove 2 hooks and then pull the Front Panel forward.
3. Removal of CD Mechanism Unit
a. Remove a connector (CB1) in Fig. 2.
b. Remove W2 and W3 from the CD Mechanism in Fig. 2.
c. Remove 4 screws ( t ) in Fig. 1.
d. Remove the CD Mechanism Unit in Fig. 1.
Top Cover w
w
q
t t
CD Mechanism
Unit
Hook
Hook
e
r
Front Panel
CDX-E400
Fig. 1
CB1
W2
CB102
W3
Fig. 2
6
CDX-E400
● Servicing Position
a. Remove the Top Cover, Front Panel and CD Mechanism Unit.
b. Remove 3 screws (y) and 2 screws (u) in Fig. 3.
c. Loosen the style pin (PN1) to set W401 free in Fig. 3.
d. With the rear panel attached, remove the Main P.C.B.
e. With the rear panel attached, set the Main P.C.B on its side as shown in Fig. 4.
At this time, fit the cut in the rear panel with the main chassis as shown in Fig. 4.
f. Replace the PU cable of the CD Mechanism with the below specified extension cable.
Extension cable
16P 230 mm: V3340500
g. Install the CD Mechanism to the frame mechanism.
h. Connect CB1 as shown in Fig. 5.
i. Connect W2 and W3 to the CD Mechanism as shown in Fig. 6.
j. Place the front panel on the base as shown in Fig. 6.
Base height: 10cm
k. Connect CB102 as shown in Fig. 6.
l. Connect the power cable, turn on the power and check for operation.
y
W401
Style Pin (PN1)
CB1
Main P.C.B.
y
Extension cable
Rear Panel
Fig. 3 Fig. 5
Main P.C.B.
CB102
CDX-E400
W3
W2
Base
Cut
Fig. 4
Fig. 6
7
CDX-E400
4. Removal of Tray Unit Stopper Pin

a. Remove 2 screws ( i ) and then remove the Chuck- Chucking Unit
ing Unit in Fig. 7. i
b. Remove 1 hook and then remove the Stopper Pin in
Fig. 7. Stopper
c. Rotate the Drive Gear and then open the Tray Unit in
Fig. 7.
d. Detach the Stoppers on both sides and then pull out
the Tray in Fig. 7.
Hook
Stopper
Drive Gear
Fig. 7
5. Removal of Pick-up Head o

a. Remove 2 screws ( o ) in Fig. 8. Sub Chassis (S)
b. Remove a pick-up cable in Fig. 8. Pick-up Cable
c. Remove 4 screws ( !0 ) and then remove the Drive
Unit in Fig. 8.
d. Remove the gear A in Fig. 9.
e. Pull out the Sled Shaft in Fig. 9.
f. Remove the Pick-up Head. Drive Unit
!0
!0
Fig. 8
Pick-up Head Gear A

CDX-E400
Sled Shaft
Check that the disc table height is as specified below.
Disc Table
19.4 ± 0.2mm
Stopper Fig. 9
8
CDX-E400
■ STANDARD OPERATION CHART
POWER ON If a disc is not loaded, “– –:– –” appears in the time indicator.
Press OPEN/CLOSE key. “ OPEN ” appears in the indicator.
Forced feed return operation “TRV” signal is output until detection of LIMIT switch.
Clamp down operation
Tray open Stop after detection of LOADING switch.
Load a disc.
Press PLAY key or push the tray.
Tray closed Proceeds to next step after detection of LOADING switch.
Disc mechanism unit clamped up.

if FLSW = L, (IC103, 21 pin)
Proceeds To Next Step.
Feed inward switch research.
Tracking offset auto ADJ
Laser ON LSON = “L” (IC101, 2 pin)
Focus offset auto ADJ
Disc scan
Focus gain rough ADJ
Focus search operation
Focus lock servo ON FLOCK = “H” → “L” (IC102, 11 pin)
Spindle motor accelerated.
Tracking servo ON TLOCK = “H” → “L” (IC102, 12 pin) CDX-E400
Spindle servo ON
VCO lock
Feed servo ON
9
CDX-E400
Tracking gain rough ADJ
Tracking balance ADJ (only tray OPEN/CLOSE)
Focus balance ADJ
Focus gain ADJ
Tracking gain ADJ
* TOC READ ~ * Data fetch cycle ~
TRACK NO. “1” is searched.
After searching the beginning, MUTE is cancelled. : MUTE OFF = “H” → “L” (Q7 Collector)
“0:00” appears in the time indicator.
~ PLAY ~
Set to SEARCH by means of Y, T key.
MUTE ON : MUTE ON = “L” → “H” (Q7 Collector)
TRACK search
After searching the beginning, MUTE is cancelled. : MUTE OFF = “H” → “L” (Q7 Collector)
“0:00” appears in the time indicator.
~ PLAY ~
Press the STOP key.
MUTE ON : MUTE ON = “L” → “H” (Q7 Collector)
Spindle motor stop

CDX-E400
Laser OFF : LSOFF = “L” → “H” (IC101, 2 pin)
Forced feed return : FLSW (IC103, 21 pin) = “L”
~ STOP ~
10
CDX-E400
■ TEST MODE
When the power off, press the “STANDBY/ON” key while pressing the “ a ” key and the “ w/d ” key and then
release your fingers from those keys.
Note: At this time, “ a ” key must be pressed before “ w/d ” key is pressd. Otherwise “ w/d ” key operation causes
product mode.
When the test mode started, the following messages are displayed.
After a second
T e st 1
● Test Mode Function List of Panel keys

PANEL KEY FUNCTION
f Execute the test command selected with the SKIP/SEARCH keys
(OPEN/CLOSE)
w/d Plays if focus servo is effective. TRON, MUTE OFF.
(PLAY/PAUSE)
a All stop. (Focus, spindle, feed, laser, tray, etc.) Initializes FL display
(STOP)
T/E
E Decrement the test command number.
(SKIP/SEARCH)
R/Y
Y Increment the test command number.
(SKIP/SEARCH)
Sample of display of test command
Command No. Command Name
02:AutoAdj 2
The functions corresponded to the test command numbers are as follows.

Command Command FUNCTION
No. Name
00 Op/Cl Tray open/close.
01 AutoAdj 1 Auto adjustment mode 1 (TR-off set, FO-off set, FO-rough gain adjustment)
02 AutoAdj 2 Auto adjustment mode 2 (TR-balance, TR-rough gain adjustment)
03 AutoAdj 3 Auto adjustment mode 3 (FO-fine gain, TR-fine gain, FO-balance adjustment)
04 TV Rev Move traverse reverse till the inner SW turn on.
CDX-E400
05 TV Fwd Move traverse forward.
06 TV Stop Stop traverse.
07 SP Accel Accelerate spindle.
08 SP Brake Decelerate spindle.
09 SP SV.On Spindle servo on.
10 SP SV.Off Spindle free (servo off)
11 SP Stop Stop spindle.
12 FO Search FOON, TROF (Enter focus search if focus servo is off.)
13 TR,TV Off FOON, TROF, TVOF(FEOF) (Enter focus search if focus servo is off.)
14 1Kick Rev Reverse 1 track kick continuously.
15 1Kick Fwd Forward 1 track kick continuously.
16 10 K. Rev Reverse 10 tracks kick continuously.
17 10 K. Fwd Forward 10 tracks kick continuously.
18 30 K. Rev Reverse 30 tracks kick continuously.
19 30 K. Fwd Forward 30 tracks kick continuously.
11
CDX-E400
Command Command FUNCTION

No. Name
20 150K. Rev Reverse 150 tracks kick continuously.
21 150K. Fwd Forward 150 tracks kick continuously.
22 PrdctMode Returns to product mode.
23 Error Msg Display the latest error message. (see page 13)
24 Test Eep Check EEPROM. (Mute on if test OK. Mute off if test NG)
25 Check FL Check FL display. (see page 12)
26 Flck/Tlck To trigger Focus lock and Track lock during play
27 S/W Vers To display current version of software
Test mode function List of Remote Controller keys

System Control KEY FUNCTION
Code
80 a All stop. (Focus, spindle, traverse, laser, tray, etc.)
81 w/d PLAY (FOON, TRON, TVON(FEON), SPON)
83 ry Move traverse forward.
84 te Move traverse reverse till the inner SW turn on.
88 RANDOM SPON (Spindle servo on.)
89 TEXT/TIME Check FL display.
8A PROG Accelerate spindle.
8B REP FOON, TROF (Enter focus search if focus servo is off.)
8C TAPE Spindle free (servo off)
90 0 Forward 150 tracks kick continuously. (Coefficient set up mode : lower digit up)
91 1 Returns to product mode.
92 2 Auto adjustment mode 1 (TR-off set, FO-off set, FO-rough gain adjustment)
93 3 Auto adjustment mode 2 (TR-balance, TR-rough gain adjustment)
94 4 Auto adjustment mode 3 (FO-fine gain, TR-fine gain, FO-balance adjustment)
95 5 Reverse 1 track kick continuously. (Coefficient set up mode : address down)
96 6 Forward 1 track kick continuously. (Coefficient set up mode : address up)
97 7 Reverse 30 tracks kick continuously. (Coefficient set up mode : upper digit down)
98 8 Forward 30 tracks kick continuously. (Coefficient set up mode : upper digit up)
99 9 Reverse 150 tracks kick continuously.(Coefficient set up mode : lower digit down)
9A +10 Change the coefficient mode.
(^Conefficient set up mode^Return to product mode with set up coefficient)
Note : Check FL display

CDX-E400
Each time the key pressed, the display changes as follows (q^w^................^o)
q Illuminate all indicators in this part. w Illuminate all indicators in this part.
e ~ u Each dot matrix changes as follows.

e r t y u
i Dot matrix illuminates like this.
o All indicators go out.
12
CDX-E400
■ ERROR MESSAGE
(1) If stopped by any cause, error message can be displayed by pressing the remote STOP key while pressing and
holding the panel STOP key, or by test mode command number 23.
The player holds the latest error message in EEPROM. So even if stopped with no error, the latest error message
can be displayed with same operation.
(2) Shown below is an example of display. (“E-73” as an example)
1 E-73
(3) Listed in the table below are error messages.
● Error Messages List
ERROR MESSAGES DESCRIPTION

E – X 0 Data cannot be read after finishing search.
E – X 1 Data cannot be read during PLAY(X=0), PAUSE(X=3), or SCAN(X=2).
E – 7 1 At the start, tracking servo is not effective. *No. for each state
E – 7 2 At the start, spindle servo PLL is not effective. (meaning of “X”)
PLAY X=“0”
E – 7 3 At the start, data can not be read.
SCAN X=“2”
E – 7 5 Tracking servo off in FO balance, or FO fine, or TR fine gain adjustment PAUSE X=“3”
and recovery action failure. PEAK SEARCH X=“4”
SEARCH X=“5”
E – 9 4 Close switch does not work with tray closed. START X=“7”
E – 9 5 Open switch does not work with tray open. STOP X=“8”
LOADING X=“9”
E – X 7 Traverse(Feed) inner switch does not work. OPEN X=“–”
E – X 8 Recovery action fails after focus drop. NO DISC X=“C”
ERROR MN35511 does not give response of SENSE, with resetting by the unit’s
microcomputer.
1) Error Code Troubleshooting

Error code X0 , X1 , 73 ...... Data cannot be read. Error codes 94 , 95 ..... Poor tray loading operation.
Does tray
Is disc dirty or YES Check by using operate when YES Loading switch detection
scratched? another disc. OPEN/CLOSE key is poor Microcomputer
pressed? defective
NO
NO
Outermost TRACKING Motor defective

Pick-up position servo defective. Control IC (IC302) defective
(on mirror FEED servo defective. Microcomputer defective
surface)
Within disc range
Pick-up defective, Spindle system

defective (Motor fails to run, etc.)
CDX-E400
Error code X7 ............. FEED operation defective. Error code X8 ............ Focus drops.
(Limit switch fails)
Is disc dirty or YES Check by using
Is forced Feed limit switch scratched? another disc.
feed operation YES
defective
available in TEST
mode? Y ...Outward Microcomputer defective
NO
T ...Inward
NO
Outermost TRACKING servo
FEED servo defective Pick-up position defective.
Microcomputer defective (on mirror FEED servo defective.
surface)
Within disc range
FOCUS servo defective

Pick-up defective
13
CDX-E400
2) Troubleshooting from System Malfunctions c) Operates as if no disc loaded. (although loaded)
a) Tray fails to come out/go in.

Does tray NO
load properly? Poor tray loading
Poor mechanism
Tray starts to YES operation
move but stops. Wire caught. YES
Loose gear, etc.
NO Is pick-up at NO
innermost position? Feed limit switch defective
Is output YES
available at LOADING Motor defective
terminal? YES
NO
Is FOCUS NO FOCUS servo
lock done? system defective
YES Microcomputer or
FLSW = “L” LOADING IC (IC302)
defective YES
NO
Does spindle NO Spindle servo
motor run? system defective
Limit switch defective
FEED servo system defective
Microcomputer defective
YES
NO
Is EFMI signal Jitter defective
normal?
When tray fails to close completely YES

(when it stops midway)
IC101 or IC102 defective
Microcomputer defective
[Corrective measure]
1) Turn ON the power and open the tray.
* If it failed to open (head and tray contacting each other), d) Sound skips.
open it after removing the chucking unit. (Time display fails to advance properly)
2) Turn OFF the power and force the tray to go in fully and
Is disc dirty, YES
close. scratched or Check by using a
warped? known good disc.
3) With the power turned ON, open and close the tray to
check if the tray close completely. NO
Poor mechanism
accuracy.
Is disc or disc YES Floating rubber/
stabilizer in contact with spring deformed.
mechanism? Pick-up connector
assembly caught.
NO
b) No sound generated, Sound cut during play.
Tracking servo system defective
( but time display advances properly) FEED servo system defective
FOCUS servo system defective
Pick-up defective
YES MUTING circuit defective
MUTING applied. Microcomputer defective
e) No search provided. (Sound skipped after search)

NO
CDX-E400
IC102 or IC4 defective Is disc dirty, YES Check by using a

scratched or known good disc.
warped?
NO
Is TER YES Tracking servo system defective

waveform normal? FEED servo system defective
FOCUS servo system defective
Pick-up defective
NO
IC102 defective.
14
CDX-E400
■ IC DATA
IC103 : µPD78076GF-108-3BA
8bit µ-COM
No. Port Name I/O Function

1 P120/RTP0 OPSW I Opened state of tray sensing switch input. Opened state at “L”.
2 P121/RTP1 CLSW I Closed state of tray sensing switch input. Closed state at “L”.
3 P122/RTP2 N.C.
4 P123/RTP3 MUTE O Sound output at “H” and sound output muted at “L”.
5 P124/RTP4 RST O Hardware reset output of MN35511. Reset at “L”.
6 P125/RTP5 DMUTE O Mute output to MN35511. Muted at “H”.
7 P126/RTP6 TLOCK I Tracking servo drawing signal input from MN35511. Drawn at “L”.
8 P127/RTP7 FLOCK I Focus servo drawing signal input from MN35511. Drawn at “L”.
9 IC IC GND
10 X2 X2
Ceramic oscillator. (5MHz)
11 X1 X1
12 VDD VDD +5V
CDX-E400
13 XT2 XT2 N.C.
14 XT1/P07 XT1 GND
15 RESET RESET I Reset input.
16 P00/INTP0/T100 REM I Pull down
17 P01/INTP1/T101 BLKCK I Sub code, block clock input from MN35511.
18 P02/INTP2 LED N.C.
19 P03/INTP3 SYSIN I System control input.
20 P04/INTP4 SYSOUT O System control output.
21 P05/INTP5 FLSW I Feed origin switch input. Feed origin at “L”.
22 P06/INTP6 CLDCK I MN35511 subcode frame clock
23 AVDD AVDD +5V
24 AVREF0 AVREF0 +5V
25 P10/ANI0 N.C.
26 P11/ANI1 N.C.
27 P12/ANI2 N.C.
15
CDX-E400
IC103 : µPD78076GF-108-3BA
8bit µ-COM

28 P13/ANI3 N.C.
29 P14/ANI4 SDA I/O DATA port for EEPROM.
30 P15/ANI5 SCL I/O DATA CLOCK for EEPROM.
31 P16/ANI6 N.C.
32 P17/ANI7 LDRCTL O Laser ON control
33 AVSS AVSS GND
34 P130/ANO0 OP/CL O N.C.
35 P131/ANO1 GCTRL O Gain and APC control
36 AVREF1 +5V
37 P70/S12/RXD SUBQ I Serial I/F input (SUBQ)
38 P71/SO2/TXD STAT I Status signal input from MN35511.
39 P72/SCK2/ASCK SQCK O Serial I/F clock (SQCK)
40 VSS VSS GND
41 P20/SI1 SUBC I Serial I/F input (CD TEXT)
42 P21/SO1 N.C.
43 P22/SCK1 SBCK2 O Serial I/F clock (CD TEXT)
44 P23/STB MLD O MN35511 chip select
45 P24/BUSY SENSE I MN35511 sense input
46 P25/SI0/SB0 SO N.C.
47 P26/SO0/SB1 MDATA O Serial I/F output (MDATA/FL driver/EEPROM)
48 P27/SCK0 MCLK O Serial I/F clock (MCLK/FL driver/EEPROM)
49 P80/A0 CS N.C.
50 P81/A1 CE O FL driver chip select
51 P82/A2 FLCE O FL driver reset
52 P83/A3 N.C.
53 P84/A4 N.C.
54 P85/A5 FEOF O Feed servo off signal output.
55 P86/A6
56 P87/A7
57 P40/AD0
58 P41/AD1
59 P42/AD2
60 P43AD3
61 P44/AD4
N.C.
62 P45/AD5
63 P46/AD6
64 P47/AD7
CDX-E400
65 P50/A8 KD4
66 P51/A9 KD3
67 P52/A10 KD2
68 P53/A11 KD1 O
Key scan
69 P54/A12 KD0 O
70 P55/A13 N.C.
71 VSS VSS GND
72 P56/A14
73 P57/A15
N.C.
74 P60 K4
75 P61 K3
76 P62 K0 I
77 P63 K1 I Key detect
78 P64/RD K2 I
79 P65/WR N.C.
80 P66/WAIT Pull down
16
CDX-E400
IC103 : µPD78076GF-108-3BA
8bit µ-COM

81 P67/ASTB Pull down
82 P100/TI5/TO5
83 P101/TI6/TO6
N.C.
84 P102
85 P103
86 P30/TO0 close O Tray open signal output
87 P31/TO1 open O Tray close signal output
88 P32/TO2
89 P33/TI1
90 P34/TI2 N.C.
91 P35/PCL
92 P36/BUZ
93 P37 STAN O M56748 standby control
94 P90 I Pull down
95 P91 I Pull down
96 P92 O Monitor 1
97 P93 O Monitor 2
98 P94 O Monitor 3
99 P95 O Monitor 4
100 P96 O Monitor (error)
IC102 : MN35511AL
Signal Processor & Controller
DEMPI/TEST2
CLVS/FLAG6
SMCK/FCLK
PCK/RESY
DEMPO
CLDCK
BLKCK
SBCK2
MDATA
CK384
IOSEL
LRCKI
SUBQ
SQCK
SDATI
VCOF
MCLK
SUBC
SBCK
AVDD
AVSS
XSEL
DSLF
PLLF
BCKI
STAT
IREF
CRC
MLD
EFM
DRF
ARF
X1
X2
17 58 59 56 19 49 69 8 7 9 44 46 45 47 48 52 53 67 62 15 14 20 68 73 72 74 75 13 55 70 78 80 79 77
VDD 60
VSS 57
DVDD1 4 TIMING DSL • PLL VCO SUBCODE
BUFFER
DVSS1 5 GENERATOR VCO DIGITAL DE-EMPHASIS
/RST 18 PITCH CONTROL
/TEST 71
A/D CONVERTER
8 TIMES
EFM DEMODULATION OVER SAMPLING
FE 32
SYNC INTERPOLATION
TE 33 DIGITAL FILTER
MICRO COMPUTER SUBCODE DEMODULATION
INTERFACE
RFENV 34 PLL
61 VCOF2
VCO 2
DD type
CDX-E400
INPUT PORT
TRCRS 37 CIRC ERROR CORRECTION DAC

SERVO 16k
DEINTERLEAVE
VDET 35 CPU SRAM
PEM PEM
BDO 39 (L) (R)
INTER POLATION
SOFT MUTING
OUTPUT D/A DIGITAL DIGITAL
CONVERTER CLV
TIMING GENERATOR
PORT ATTENUATION AUDIO

SERVO
/RFDET 38 INTERFACE
PEAK DETECT
AUTO CUE
SERVO
OFT 36
10 43 41 40 11 12 30 31 28 27 22 25 42 29 26 21 16 1 3 2 23 24 6 76 54 51 63 64 66 65 50
SENSE
WVEL
TOFS
LDON
/FLOCK
/TLOCK
FBAL
TBAL
FOD
TRD
TVD
ECS
PLAY/TRVSTP
VREF
KICK
TRV
DMUTE
BCLK
SRDATA
LRCK
PC
ECM
TX
IPFLAG
FLAG
AVSS2
OUT1C
OUT1D
OUT2C
OUT2D
AVDD2
17
CDX-E400
IC102 : MN35511AL
Pin No. Name I/O Function

1 BCLK O Bit clock output for SR DATA (NC)
2 LRCK O L/R identification signal output (NC)
3 SRDATA O Serial data output (NC)
4 DVDD1 I Power supply for digital circuit (+5)
5 DVSS1 I GND for digital circuit
6 TX O Digital, audio, interface output signal
7 MCLK I Microprocessor command clock signal input (data latched at leading edge)
8 MDATA I Microprocessor command data input
9 MLD I Microprocessor command load signal input (L : LOAD)
10 SENSE O Sense signal output (OFT, FESL, NACEND, NAJEND, SFG, NWTEND)
11 FLOCK O Focus servo drawing signal (L : when drawn)
12 TLOCK O Tracking servo drawing signal (L : when drawn)
13 BLKCK O Sub code block clock signal (BLKCK=75Hz)
14 SQCK I Clock input for sub-code Q register
15 SUBQ O Sub-code Q code output
16 DMUTE I Muting input (H : MUTE)
17 STAT O Status signal (CRC, STCNT, CLVS, TTSTOP, SQOK, RESY, FCLV, FLAG6, SENSE ,/FLOCK, /RFDET, /TLOCK)
18 RST I Reset input (L : RESET)
19 SMCK/ O 4.2336MHz clock signal output SMCK when command is defaulted. (Note 1) (NC)
FCLK SMCK (8.4672MHz), FCLK (7.35kHz) or “L” fixed is selected when command is switched.
20 CLVS/ O With command defaulted : CLVS when IOSEL=H, FLAG6 when IOSEL=L (NC)
FLAG6 These settings can be reversed by command (FLAG6 when IOSEL=H).
21 TRV O Traverse (Feed) forced feed output 3-State
22 TVD O Traverse (Feed) drive output
23 PC O Spindle motor ON signal L : ON (default) (NC)
24 ECM O Spindle motor drive signal (forced mode output) 3-State
25 ECS O Spindle motor drive signal (servo error signal output)
26 KICK O Kick pulse output 3-State
27 TRD O Tracking drive output
28 FOD O Focus drive output
29 VREF I Reference voltage for DA output block (TVD, ECS, TRD, FOD, FBAL, TBAL)
30 FBAL O Focus balance adjustment output
31 TBAL O Tracking balance adjustment output
32 FE I Focus error signal input (analog input)
33 TE I Tracking error signal input (analog input)
34 RFENV I RF envelope signal input (analog input)
35 VDET I Oscillation detect signal input (H : DETECT) (GND)
CDX-E400
36 OFT I Off track signal input (H : OFF TRACK)

37 TRCRS I Track cross signal input (analog input)
38 RFDET I RF detect signal input (L : DETECT)
39 BDO I Drop out signal input (H : DROP OUT)
40 LDON O Laser ON signal output (H : ON) (NC)
41 TOFS O Tracking offset adjustment output (NC)
42 PLAY/TRVSTOP O Switched by command. PLAY (Play signal output) when command is defaulted. (NC)
43 WVEL O Double speed status signal output (H : double speed) (NC)
44 ARF I RF signal input
45 IREF I Reference current input terminal
46 DRF I Bias terminal for DSL
(Note 1) At the SMCK/FCLK pin, output does not stop while /RST=L.
18
CDX-E400
IC102 : MN35511AL
Pin No. Name I/O Function

47 DSLF I/O Loop filter terminal for DSL
48 PLLF I/O Loop filter terminal for PLL
49 VCOF I/O Loop filter terminal for VCO (+5)
50 AVDD2 I Power supply for analog circuit (for AD of DSL, PLL, DA output blocks) (+5)
51 AVSS2 I GND for analog circuit (for AD of DSL, PLL, DA output blocks) (GND)
52 EFM O EFM signal output (NC)
53 PCK/ O With command defaulted : PLL extract clock output PCK when IOSEL=H, frame re-synchronous signal RESY when IOSEL=L
RESY These settings can be reversed by command (RESY when IOSEL=H). (NC)
54 FLAG O Flag signal output (NC)
55 CRC O Sub-code CRC check result output (H : OK, L : NG) (NC)
56 XSEL I L : Normal mode (GND)
H : • For internal master clock, VCO2 output clock for jitter adsorbing PLL is used instead of Xtal
oscillation output (X2).
• VCO2 is always fixed to oscillation mode regardless of VCO2 oscillation stop command or
resetting (/RST=L) and Xtal oscillation is stopped.
57 VSS I GND for oscillation circuit
58 X1 I Crystal oscillation circuit input terminal
59 X2 O Crystal oscillation circuit output terminal
60 VDD I Power supply for oscillation circuit (+5)
61 VCOF2 O PLL loop filter terminal for jitter adsorption (GND)
62 AVSS1 O GND for audio DAC
63 OUT1C O PEM output terminal 1C
64 OUT1D O PEM output terminal 1D
65 OUT2D O PEM output terminal 2D
66 OUT2C O PEM output terminal 2C
67 AVDD1 I Power supply terminal for audio DAC
68 DEMPO O Deemphasis detect signal output (NC)
69 CK384 O 384fs clock output (At the CK384 pin, output does not stop while /RST=L.) (NC)
Xtal system when command is defaulted. Signal processing system when command is switched
70 IOSEL I Mode selecting terminal (+5)
71 TEST I Test mode setting terminal (Normal : H) (+5)
72 SBCK2 I Sub-code data read clock input
73 SUBC O Sub-code serial output (SBCK effective) when command is defaulted.
PACK data usable (SBCK2 effective) when command is switched
74 SBCK I Clock input for sub-code serial output (with pull-up resistor) (NC)
75 CLDCK O Sub-code frame clock signal output when command is defaulted (fCLDCK=7.35kHz)
PACK synchronous signal when command is switched
CDX-E400
76 IPFLAG O Interpolation flag signal output (H : INTERPOLATION) (NC)
77 DEMPI I When IOSEL=H, L : NORMAL H : TEST2 (GND)
/TEST2 Emphasis control in accordance with DEMP0
When IOSEL=L, external DEMP1 input terminal
For emphasis control, DEMP0, OR of DEMP1, DEMP1, forced OFF or forced ON is selected by command.
When command is defaulted, DEMP0 and OR of DEMP1
78 SDATI I SRDATA input (effective only when IOSEL=L) (NC)
79 LRCKI I LRCK input (effective only when IOSEL=L) H : Lch data, L : Rch data (NC)
80 BCKI I BCK input (effective only when IOSEL=L) (NC)
19
CDX-E400
■ DISPLAY DATA (V3618100)

V301 : 14-BT-56GN #6
&0
PATTERN AREA
q #5
● PIN CONNECTION
Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30
Connection F1 F1 NP 14G 13G 12G 11G 10G 9G 8G 7G 6G 5G 4G 3G 2G NX NX NX NX 1G IC P35 P34 P33 P32 P31 P30 P29 P28
Pin No. 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
Connection P27 P26 NP F2 F2 F2 F2 NP P25 P24 P23 P22 P21 P20 P19 P18 P17 P16 P15 P14 P13 NX NX NX NX P12 P11 P10 P9 P8
Pin No. 61 62 63 64 65 66 67 68 69 70
Connection P7 P6 P5 P4 P3 P2 P1 NP F1 F1
Note 1) F1, F2 ......... Filament 3) NX .............. No Extend pin 5) 1G~14G ...... Grid
2) NP .............. No Pin 4) P1~P35 ....... Datum Line 6) IC ................ Internal Connection
● GRID ASSIGNMENT ● ANODE CONNECTION

CDX-E400
20
A B C D E F G H
CDX-E400
■ BLOCK DIAGRAM
1
CD MECHA. UNIT
XL101
PICK UP
58 59
VCC VCC +5
28
E EFM
5
32 +5 TP1 LPF
D IC3 IC3 PJ1
29 9 ARF 2 1 5 7
A ARF 44 63 OUT L
64
L
31
B 18
30 HEAD
C AMP Q3 Q4
27
F
IC101 CONTROL
2 AN8399SA LINE OUT
GND
7 Q5 Q6
LD DRIVE 2 LPF
LD IC102 IC105
Q1 IC105
MN35511AL
VREF 29 65 OUT R 2 1 5 7
VR R
66
1 SPC+DAC
MON FDO 28
IC303 MUTE
M56789FP KICK 26 CONTROL
41 Q7
TRD 27 D1—5
12
FA+
15
TRACKING
13 ECM 24
FOCUS
TA+
ECS 25 6 TX DIGITAL OUT
CB6
TA— OPTICAL
9
3 FA—
6 TRV 21 8 MDATA
10
TVD 22 7 MCLK
32
SPDL+ 18
CONTROL
27
SPINDLE 31
M SPDL—
34
FEED+ 5
39
FEED 36 47 MDATA
M FEED— 10
17,20 48 MCLK
FLSW +5M
FLSW XL102
GND 11 4 MUTE
JK1
LDRCTL 32 15 RESET
19 IN
4 FLSW 21 20 OUT
D105 SYSCON
SYSTEM
CONNECTOR
-VB -5 +5 +5M +VB
29 SDA 5 POWER
SYSTEM CONTROL IC104 RESET 8 SUPPLY
IC103 EEP ROM IC4
30 SCL 6 (IC4)
S-24CO1ADP
8bit CPU Q8—10
VF D6—9, 11, 13
PD78076GF
IC302
LB1641 D12
7 T401
+VB
5 2 6 CLOSE 86
47
48
61 DISPLAY DRIVE
DISPLAY
LOADING+ | IC301
50 V301
LOADING 64 LC75710NE L401
10 5 OPEN 87 51
M LOADING—
1 30 31 57 58
KD0, KD1 F1 ACF
68
OPSW 1 69
OPEN F2 ACF
LOADING
GND
SW
CLSW 2 76 KEY MATRIX
CLOSE | K0-K2 SW301—306
78
21
6

A B C D E F G H
CDX-E400
■ PRINTED CIRCUIT BOARD (Foil side)

1
● Semiconductor Location MAIN ( 1 ) P. C. B.
Ref. No. Location
D1 D2
TO : CD MECHANISM UNIT
TO : CD MECHANISM UNIT
D2 D2
D3 D3
D4 D3 FROM : CD MECHANISM UNIT
D5 D3
D6 C2
D10 D3
D11 C3 5 FA–
D12 C3 TA–
TA+
FA+
D13 C3 GND
PD
D14 C2 LD
GND
F
D101 F4 C
D102 F4 FROM : MAIN (3) A

E
B
D
+5V
D103 F4 VREF
42
1
D104 F4
D105 F3
FL2
FL1
AC
GND
AC
2 D106 F3
Ref. No. Location 32

1
IC3 C4
21
22
IC4 C3 4
W2
W3
IC101 E2
B
17
IC102 D3
16
IC103 F4
IC104 E3
IC105 C3
CONNECTOR
IC302 F3
IC303 F2
SYSTEM
10
1
1
16
DGND
FLSW
FEED–
FEED+
SPDL–
SPDL+
Ref. No. Location
Q1 F2
Q2 F2
Q3 B4
(OPTICAL)
3 Q4 B4
DIGITAL
Q5 B3
9
CLSW
DGND
OPSW
LOAD–
LOAD+
OUT
Q6 B3
Q7 D3
40
21
Q8 C3
41
20
Q9 D3
Q10 C3
Q102 E3
8
5
ANALOG
60
4
1
KD0
30
61
80
KD1
1
OUT
K2
100
K1
31
K0
5
+5
VP
8
1
GND
CL DI
/BLK CE
8
FL2
1
FL1
50
81
51
80
4
5
4
4 A 1 2 FROM : MAIN (2)
Point t (EFN)
V : 0.2V/div, H : 0.5µsec/div
AC, 1 : 1 probe
Point r-A (/RESET : Pin 8 of IC4)

5 Point r-B (VCC : Pin 16 of IC4)
Point q (Pin 59 of IC102) Point w (Pin 10 of IC103) V : 2V/div (/RESET), V : 5V/div (VCC)
DC, 1 : 1 probe, H : 5 sec/div
V : 2V/div, H : 50nsec/div V : 2V/div, H : 0.2µsec/div
DC, 1 : 1 probe DC, 1 : 1 probe
/RESET
Test disc
0V 0V
VCC SONY YEDS-18 (P/No. TX911730)
A-BEX TCD-782 (P/N. TX913350)
AC CORD : ON AC CORD : OFF
or Philips 5 : x1
22
6

A B C D E F G H
CDX-E400
■ PRINTED CIRCUIT BOARD (Foil side)

1 Point e (Pin 58 of IC301)
MAIN ( 2 ) P. C. B.
V : 2V/div, H : 0.2µsec/div
DC, 1 : 1 probe
3
FROM : MAIN (1)
0V
STANDBY/
48
49
ON
2
64
3
KD0
32 3
KD1 K2
K1 K0
1
+5 VP
GND DI
CL CE
17
/BLK
16
FL2
FL1
MAIN ( 3 ) P. C. B. MAIN ( 4 ) P. C. B.
VOLTAGE
FROM : POWER CABLE SELECTOR
(R only)
SW501
110V RE – YE
120V OR – YE
220V WH – YE
4
240V BE – YE
OR
RE
WH
OR
RE
YE
BE
R only
R only
WH R only
YE R only
BE
5 B, G only
R only
GND
FL2
FL1
AC
AC
L402
#7
W401
TO : MAIN (1)
23
6

A B C D E F G H
CDX-E400
■ IC BLOCK
1
IC303 : M56789FP IC101 : AN8399SA IC301 : LC75710NE
4-Channel Actuator Driver CD Head Amp FL Driver
RF OUT
COFTR
CAGC
CBDO
AA8/G12
AA7/G13
AA6/G14
AA5/G15
AA4/G16
OFTR
RF IN
BDO
RFN
ARF
OP1 OP1
AA35
AA34
AA33
OP2 OP2
G10
G11
AA3
AA2
AA1
+ – OP2 + – OP1 CG
G7
G8
G9
CONTROL
DI ROM
LATCH
VREFO VREF OUT OUT VCC2
LATCH
CL SHIFT DC RAM AM1
40 41 23 22 21 24 25 28 42 4 5 6 8 9 12 13 14 15
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
REGISTER
G6 49 32 AM32 CG AM2
SOUT1 19 60K 60K CE
5K 10K G5 50 31 AM31 ROM
28 Vm2
SIN1– 18
DRIVER
ANODE
G4 51 30 AM30
S1 + G3 52 29 AM29
A3 + + + A1 RF EQ AGC BDO OFTR ADDRESS ADDRESS AD
+ A2 A4 A4 G2 53 28 AM28 VDD REGISTER COUNTER AM35
RAM
5K 10K OP2 OP1 10 CEA G1 54 27 AM27
VSS
AA1
VFL 55 26 AM26 BLINKCYCLE BLINK AA2
+ NRFDET 3TENV AM25 REGISTER GENERATOR
IN1+ 16 + TEST 56 25 VFL AA3
A3 A1 11 3T OUT AM24
IN1– 15 27 IN4B– VSS 57 24 AA4/G16
E1 E44K 25K 58 23 AM23 RES DISPLAY DISPLAY
OUT1 14 OSCO REGISTER CONTROL AA5/G15
30 IN4A– A 32 16 NRFDET 59 22 AM22
OSCI TEST AA6/G14
+
VCC2 +
VDD 60 21 AM21 DUTYCYCLE DUTY AA7/G13
VM1(+) 12 CH1 CH4 32 VM4(+) AMP GCA BCA RES 61 20 AM20 REGISTER GENERATOR AA8/G12
DIFFERENTIAL DIFFERENTIAL C 31 22 FEN
VOLTAGE VOLTAGE CE 62 19 AM19 G11
2 VM1(–) 13
+
GAIN
x5
VREF0
GAIN
x 10 +
31 VM4(–)
B 30
SUBT
–
+ 23 FEOUT
CL 63
64
18
17
AM18
AM17
GRID
REGISTER
GRID
CONTROL
G10
DI
10
11
12
13
14
15
16
1
2
3
4
5
6
7
8
9
DRIVER
GRID
+ + INSTRUCTION
VM2(–) 9 CH3 35 AMP GCA BCA CONTROL
CH2 VM3(–) DECODER
AM1
AM2
AM3
AM4
AM5
AM6
AM7
AM8
AM9
AM10
AM11
AM12
AM13
AM14
AM15
AM16
BIAS D 29
DIFFERENTIAL DIFFERENTIAL OSC I G2
VOLTAGE VCC1 VOLTAGE TIMING
VM2(+) 10 GAIN GAIN 34 VM3(+) OSC DIVIDER GENERATOR DECODER G1
+ x5 x 10 + E 27 AMP GCA BCA OSC O
Hi:Sleep
20 TEN
OUT2 8
E2 –
IN2– 6 39 IN3– SUBT
+
A3 A3 + 21 TE OUT
IN2+ 5 E3 + 38 IN3+
TSD 36 OUT3 F 28 AMP GCA BCA
1ch 4ch
5K 10K 25K 25K SLEEP
2ch
+
A3 3ch A1
S2 23K 23K + –
SIN2– 4 + 2 LD
37 Vm3
5K 10K 60K 60K +
SOUT2 3 VREF 19
17 2 1 7 11 29 33 20 –
Vm1 MUTE1 MUTE2 VCC1 1 PD
GND(4PIN)
BAND GAP
■ PIN CONNECTION DIAGRAM
3 18 24 26 25 7 17 3
S1NB20
SLPSW
GCTL
TBAL
FBAL
LDRCTL
GND
VCC
DIN60-4084
1SS133
MTZJ4.3A
MTZJ5.1B Anode
IC302 : LB1641 MTZJ5.6B
Motor Driver MTZJ30.0B
–
+
VCC 2
VCC 1
OUT 1
OUT 2
Cathode
IC3, 105 : NJM2068D-D
P1
P2
3 2 8 10 9 7 Dual OP-Amp
IC104 : S-24C01ADP
Electrically Erasable PROM 2SA933S(Q,R) 2SB544(E,F,G) 2SA1708(S,T) 2SB1565(E,F) LB1641
2SD1915(F)ST 2SD2396(J,K)
PRE DRIVER
OUT1 1 8 +VCC
VCC 8 START
4 VZ CYCLE H.V.GENERATION
–IN1 2 7 OUT2 TIMING &
+ – + – VSS 4 CONTROL
+IN1 3 6 –IN2 SDA 5 START 10
STOP
B
C B
LOGIC
E E C
–VCC 4 5 +IN2 E2 PROM E
CONTROL C
LOGIC XDEC 32
32X32 B BC
SCL 6 E 1
4 IN 1 5 INPUT LOGIC 6 IN 2
LOAD INC
5 32
WORD 2
GND 1
NC 1
ADDRESS YDEC S-24C01ADP M5290P M56789FP M56789FP
COUNTER
NC 8
NJM2068D-D
2 15
CK
NC 3 PIN DATA REGISTER
NC 7 DOUT DOUT
ACK 14
4 8 21
8 28
1 16 42
1
IC4 : M5290P 1
1
Constant-Voltage Tracking Supply with Reset
OUTPUT LC75710NE MN35511AL µPD78076GF-108-3BA
VCC E– C+ NC (+5V) DELAY
16 15 14 13 12 7 48 33 60 41
49 32 80 51
61 40
81 50
11
REFERENCE
IN
5 +
CIRCUIT
DELAY
8 RESET OUT 64 17
REFERENCE CURRENT
PROTECTION
REGULATOR CONTROL 1 16
GND 9 80 21 100 31
ON/OFF 1 30
ON/OFF 10 CONTROL 1 20
+
6 BAL. ADJ.
CURRENT
CONTROL
1 3 2 4 5
–VCC E– C– NC OUTPUT
(–5V)
24
6

A B C D E F G H I J K L M N
CDX-E400
■ SCHEMATIC DIAGRAM
1
0 5.1 MUTING
0
0
0 5.1 0
2.5
2.5
0
2.5
0
2.6
2.6
2.6
2.5
0 0
2.4
2.5
2.5
2.5
2.5
2.5
2.4
2.6
0
0
–5.0
–5.0
0 0
5.0
2.6 ~
1.4 5.1
2.6 SPC & DAC ~
2.6 5.1
2 0 0
–5.0
2.1 5.1
5.1 0 –5.1
5.1 5.1 0
0 0 0
4.9 0 0 0 5.1
5.1 0
1.1 ~ 0 –5.0
0
~
q
2.6
2.6
0 0
2.5
2.5
2.6
0
2.4
LD DRIVE
2.5
2.5
2.6
2.6
2.6
2.6
2.7
2.6
2.5
2.6
2.5
0
2.5
2.5
2.5
2.5
5.1
CD HEAD AMP
0
0.2
3.9
5.1
5.1
5.1
~
0
5.0
0
5.1
5.1
2.6
4.6
2.5
2.5
2.5
3.5
3.9
4.1
2.6
0
0
2.5
t
MUTE CONTROL
5.2 –10.2 –0.4
–0.5
5.2
5.1 5.2 10.2
2.5 5.2 5.2 5.2
5.0
0 0
4 2.6
EEPROM
5.1
ACT. MOTOR DRIVER
POWER SUPPLY
5.1
2.5
2.5
5.1
~
0
5.1
~
0
~
~
~
0
~
5.1
5.1
5.1
0
5.1
2.5
–12.6
–12.6
–5.0
–5.0
5.1
1.3
5.1
0
0
5.1
2.5 5.1
SYSTEM CONTROL 0 0 0
rB AC19.6
1.2
5.1
0
9.4
0
10.2
0 Z
0 Z
5
rA
9.4
5.1
0
~ 5.1 5.1 10.2
~ 5.1 5.1 µPD78076GF-108-3BA 5.1
2.4 AC3.7
5.1 2.8
5.1 5.1 5.1 0 0 5.1
0 10.2
0
5.5
0 5.5
w 5.1
5.0
0
5.1 0
5.1
0
0
0
0
0
0
0
–22.1
5.1
–28.2 –32.1 –22.1

MOTOR DRIVER
–28.2
–28.8
6 –12.6
–22.6
0
7
CIRCUIT CHANGES BY MARKET.
~ ~
~ ~ Z
~ ~
~
Z
~ Z
Point r-A (/RESET : Pin 8 of IC4) ~ ~
Point q (Pin 59 of IC102)
V : 2V/div, H : 50nsec/div
Point r-B (VCC : Pin 16 of IC4)
V : 2V/div (/RESET), V : 5V/div (VCC)
~
~
e ~
~
DC, 1 : 1 probe ~ ~
DC, 1 : 1 probe, H : 5 sec/div ~ ~
~
~
~
0V
/RESET
~
~
FL DRIVER ~
8 ~ ~
~
VCC
~
O : USED X : NOT USED

~
~
~
~
~
~
~
~
~
~
~
~
~
~
~
AC CORD : ON AC CORD : OFF
Point w (Pin 10 of IC103)

–22.3
–22.3
–22.3
~
~
~
~
~
~
~
~
~
~
~
~
~
~
~
~
~
~
~
~
~
~
~
~
~
–22.3
DC, 1 : 1 probe
Point t (EFN)
V : 0.2V/div, H : 0.5µsec/div
0V
AC, 1 : 1 probe
~
~
~
~
~
~
~
~
~
~
~
~
~
~
~
~
~
~
~
~
~
~
~
Point e (Pin 58 of IC301)

DC, 1 : 1 probe
0V
Test disc
SONY YEDS-18 (P/No. TX911730)
A-BEX TCD-782 (P/N. TX913350)
or Philips 5 : x1
10
* All voltage are measured with a 10M Ω /V DC electric volt meter.

* Components having special characteristics are marked Z and
must be replaced with parts having specifications equal to those
originally installed.
* Schematic diagram is subject to change without notice.
25

CDX-E400
■ WARNING
PARTS LIST Components having special characteristics are marked Z and must be
replaced with parts having specifications equal to those originally installed.
■ ELECTRICAL PARTS ● Carbon resistors (1/6W or 1/4W) are not included in the ELECTRICAL PARTS
List. For the part Nos. of the carbon resistors, refer to the last page.
ABBREVIATIONS IN THIS LIST ARE AS FOLLOWS :
C.A.EL.CHP : CHIP ALUMI. ELECTROLYTIC CAP L.EMIT : LIGHT EMITTING MODULE

C.CE : CERAMIC CAP LED.DSPLY : LED DISPLAY
C.CE.ARRAY : CERAMIC CAP ARRAY LED.INFRD : LED, INFRARED
C.CE.CHP : CHIP CERAMIC CAP MODUL.RF : MODULATOR, RF
C.CE.ML : MULTILAYER CERAMIC CAP PHOT.CPL : PHOTO COUPLER
C.CE.M.CHP : CHIP MULTILAYER CERAMIC CAP PHOT.INTR : PHOTO INTERRUPTER
C.CE.SAFTY : RECOGNIZED CERAMIC CAP PHOT.RFLCT : PHOTO REFLECTOR
C.CE.TUBLR : CERAMIC TUBULAR CAP PIN.TEST : PIN, TEST POINT
C.CE.SMI : SEMI CONDUCTIVE CERAMIC CAP PLST.RIVET : PLASTIC RIVET
C.EL : ELECTROLYTIC CAP R.ARRAY : RESISTOR ARRAY
C.MICA : MICA CAP R.CAR : CARBON RESISTOR
C.ML.FLM : MULTILAYER FILM CAP R.CAR.CHP : CHIP RESISTOR
C.MP : METALLIZED PAPER CAP R.CAR.FP : FLAME PROOF CARBON RESISTOR
C.MYLAR : MYLAR FILM CAP R.FUS : FUSABLE RESISTOR
C.MYLAR.ML : MULTILAYER MYLAR FILM CAP R.MTL.CHP : CHIP METAL FILM RESISTOR
C.PAPER : PAPER CAPACITOR R.MTL.FLM : METAL FILM RESISTOR
C.PLS : POLYSTYRENE FILM CAP R.MTL.OXD : METAL OXIDE FILM RESISTOR
C.POL : POLYESTER FILM CAP R.MTL.PLAT : METAL PLATE RESISTOR
C.POLY : POLYETHYLENE FILM CAP RSNR.CE : CERAMIC RESONATOR
C.PP : POLYPROPYLENE FILM CAP RSNR.CRYS : CRYSTAL RESONATOR
C.TNTL : TANTALUM CAP R.TW.CEM : TWIN CEMENT FIXED RESISTOR
C.TNTL.CHP : CHIP TANTALUM CAP R.WW : WIRE WOUND RESISTOR
C.TRIM : TRIMMER CAP SCR.BND.HD : BIND HEAD B-TITE SCREW
CN : CONNECTOR SCR.BW.HD : BW HEAD TAPPING SCREW
CN.BS.PIN : CONNECTOR, BASE PIN SCR.CUP : CUP TITE SCREW
CN.CANNON : CONNECTOR, CANNON SCR.TERM : SCREW TERMINAL
CN.DIN : CONNECTOR, DIN SCR.TR : SCREW, TRANSISTOR
CN.FLAT : CONNECTOR, FLAT CABLE SUPRT.PCB : SUPPORT, P.C.B.
CN.POST : CONNECTOR, BASE POST SURG.PRTCT : SURGE PROTECTOR
COIL.MX.AM : COIL, AM MIX SW.TACT : TACT SWITCH
COIL.AT.FM : COIL, FM ANTENNA SW.LEAF : LEAF SWITCH
COIL.DT.FM : COIL, FM DETECT SW.LEVER : LEVER SWITCH
COIL.MX.FM : COIL, FM MIX SW.MICRO : MICRO SWITCH
COIL.OUTPT : OUTPUT COIL SW.PUSH : PUSH SWITCH
DIOD.ARRAY : DIODE ARRAY SW.RT.ENC : ROTARY ENCODER
DIODE.BRG : DIODE BRIDGE SW.RT.MTR : ROTARY SWITCH WITH MOTOR
DIODE.CHP : CHIP DIODE SW.RT : ROTARY SWITCH
DIODE.VAR : VARACTOR DIODE SW.SLIDE : SLIDE SWITCH
DIOD.Z.CHP : CHIP ZENER DIODE TERM.SP : SPEAKER TERMINAL
DIODE.ZENR : ZENER DIODE TERM.WRAP : WRAPPING TERMINAL
DSCR.CE : CERAMIC DISCRIMINATOR THRMST.CHP : CHIP THERMISTOR
FER.BEAD : FERRITE BEADS TR.CHP : CHIP TRANSISTOR
CDX-E400
FER.CORE : FERRITE CORE TR.DGT : DIGITAL TRANSISTOR
FET.CHP : CHIP FET TR.DGT.CHP : CHIP DIGITAL TRANSISTOR
FL.DSPLY : FLUORESCENT DISPLAY TRANS : TRANSFORMER
FLTR.CE : CERAMIC FILTER TRANS.PULS : PULSE TRANSFORMER
FLTR.COMB : COMB FILTER MODULE TRANS.PWR : POWER TRANSFORMER ASS’y
FLTR.LC.RF : LC FILTER ,EMI TUNER.AM : TUNER PACK, AM
GND.MTL : GROUND PLATE TUNER.FM : TUNER PACK, FM
GND.TERM : GROUND TERMINAL TUNER.PK : FRONT-END TUNER PACK
HOLDER.FUS : FUSE HOLDER VR : ROTARY POTENTIOMETER
IC.PRTCT : IC PROTECTOR VR.MTR : POTENTIOMETER WITH MOTOR
JUMPER.CN : JUMPER CONNECTOR VR.SW : POTENTIOMETER WITH ROTARY SW
JUMPER.TST : JUMPER, TEST POINT VR.SLIDE : SLIDE POTENTIOMETER
L.DTCT : LIGHT DETECTING MODULE VR.TRIM : TRIMMER POTENTIOMETER
Note) Those parts marked with “#” are not included in the P.C.B. ass'y.
27
CDX-E400
% : Note on the Main PCB

Of the main PCB part Nos., only the gold (GD) type part Nos. are included in the table. (G, B models)
The only different part between the silver (SI) and gold (GD) type parts is the sheet/FL that is attached to the
fluorescent character display tube. When a SI type main PCB becomes necessary, order a GD type main PCB and a
SI type sheet/FL (V3688400) and replace the sheet/FL of the GD type main PCB with the SI type sheet/FL.
Schm Schm
Ref. PART NO. Description Market Ref. PART NO. Description Market
* V9356200 P.C.B. GD:MAIN R C104 V4749000 C.EL 150uF 6.3V
* V9356300 P.C.B. GD:MAIN GB C105 VG277700 C.CE.TUBLR 68pF 50V
CB1 V2731000 CN.FMN 16P C106 UA653100 C.MYLAR 1000pF 50V
CB6 V4164300 L.EMIT TOTX178A C107 UA653150 C.MYLAR 1500pF 50V
CB7 VB390100 CN.BS.PIN 5P C108 UA654470 C.MYLAR 0.047uF 50V
CB102 VN394900 CN.BS.PIN 14P C109 UN865470 C.EL 0.47uF 50V
CB301 VF982200 CN.BS.PIN 14P C110 VE326000 C.MYLAR.ML 0.1uF 50V
CB401 VG879900 CN.BS.PIN 2P C111 V4749000 C.EL 150uF 6.3V
C1 UR818100 C.EL 100uF 6.3V C112 UR818100 C.EL 100uF 6.3V
C2 VJ599100 C.CE.TUBLR 0.1uF 50V C113 VJ599100 C.CE.TUBLR 0.1uF 50V
C3 UR818100 C.EL 100uF 6.3V C114 VJ599000 C.CE.TUBLR 0.047uF 16V
C4 UR818100 C.EL 100uF 6.3V C115 UN865100 C.EL 0.10uF 50V
C5 UR837470 C.EL 47uF 16V C116 UA654470 C.MYLAR 0.047uF 50V
C6 VF467000 C.CE.TUBLR 1000pF 50V * C117 UA653680 C.MYLAR 6800pF 50V
C8 UR838220 C.EL 220uF 16V C118 UA654470 C.MYLAR 0.047uF 50V
C10 UR838220 C.EL 220uF 16V C120 VG276600 C.CE.TUBLR 22pF 50V
C11 VE326000 C.MYLAR.ML 0.1uF 50V C122 VJ599100 C.CE.TUBLR 0.1uF 50V
C12 UN865220 C.EL 0.22uF 50V C123 VF466900 C.CE.TUBLR 470pF 50V
C15 UA654150 C.MYLAR 0.015uF 50V C124 UM397470 C.EL 47uF 16V
C16 UA653330 C.MYLAR 3300pF 50V C125 UA654680 C.MYLAR 0.068uF 50V
C19 UA653330 C.MYLAR 3300pF 50V C126 VJ599100 C.CE.TUBLR 0.1uF 50V
C20 UA654150 C.MYLAR 0.015uF 50V C127 VE326000 C.MYLAR.ML 0.1uF 50V
C21 VG287300 C.EL 22uF 50V C128 VJ599100 C.CE.TUBLR 0.1uF 50V
C23 UA653220 C.MYLAR 2200pF 50V C130 VA761400 C.CE 47pF 50V
C24 UA653220 C.MYLAR 2200pF 50V C131 VA761400 C.CE 47pF 50V
C25 UA652220 C.MYLAR 220pF 50V C132 VG290600 C.EL 2.2uF 50V
C26 UA652220 C.MYLAR 220pF 50V C133 VG290600 C.EL 2.2uF 50V
C27 VF466800 C.CE.TUBLR 100pF 50V C134 VG290600 C.EL 2.2uF 50V
C28 VF467300 C.CE.TUBLR 0.01uF 16V C135 VG290600 C.EL 2.2uF 50V
C29 VJ599100 C.CE.TUBLR 0.1uF 50V C136 VG286500 C.EL 470uF 10V
C30 UR848220 C.EL 220uF 25V C137 Vi716700 C.MYLAR 0.01uF 50V
C31 VG286200 C.EL 100uF 10V C138 UR818100 C.EL 100uF 6.3V
C32 VJ599100 C.CE.TUBLR 0.1uF 50V C139 VJ599100 C.CE.TUBLR 0.1uF 50V
C33 UR865680 C.EL 0.68uF 50V C140 VJ599100 C.CE.TUBLR 0.1uF 50V
C35 UR837100 C.EL 10uF 16V C142 VJ599100 C.CE.TUBLR 0.1uF 50V
C36 VG287900 C.EL 470uF 16V C143 UR818100 C.EL 100uF 6.3V
CDX-E400
Z C37 VK534100 C.PP 0.01uF 100V C144 VF467300 C.CE.TUBLR 0.01uF 16V
C38 Vi578400 C.EL 6800uF 16V C145 UA652100 C.MYLAR 100pF 50V
Z C39 VK534100 C.PP 0.01uF 100V C146 UA652470 C.MYLAR 470pF 50V
C40 UR837470 C.EL 47uF 16V C147 UA652470 C.MYLAR 470pF 50V
C41 UR828100 C.EL 100uF 10V C148 UA652100 C.MYLAR 100pF 50V
C42 UR867470 C.EL 47uF 50V C149 VG286200 C.EL 100uF 10V
C43 UR866470 C.EL 4.7uF 50V C150 VG286200 C.EL 100uF 10V
C45 UR867470 C.EL 47uF 50V C152 UR818100 C.EL 100uF 6.3V
C47 UR868100 C.EL 100uF 50V C301 VJ599100 C.CE.TUBLR 0.1uF 50V
C48 Vi716700 C.MYLAR 0.01uF 50V C302 VJ599100 C.CE.TUBLR 0.1uF 50V
C101 VJ599100 C.CE.TUBLR 0.1uF 50V C303 VG276600 C.CE.TUBLR 22pF 50V
C102 VJ599100 C.CE.TUBLR 0.1uF 50V * C401 VR814900 C.CE.SAFTY 0.047uF 250V
C103 VJ599100 C.CE.TUBLR 0.1uF 50V C402 UA654100 C.MYLAR 0.01uF 50V
* New Parts * New Parts

28
CDX-E400
Schm Schm
Ref. PART NO. Description Market Ref. PART NO. Description Market
C403 UR828100 C.EL 100uF 10V ST501 V4040500 SCR.TERM M3 R
Z * D1 V8911600 DIODE DIN60-4084 ST502 V4040500 SCR.TERM M3 R
Z * D2 V8911600 DIODE DIN60-4084 SW301 VV020300 SW.TACT SKQNAA
D3 VD631600 DIODE 1SS133,176 SW302 VV020300 SW.TACT SKQNAA
D4 VD631600 DIODE 1SS133,176 SW303 VV020300 SW.TACT SKQNAA
D5 VG437400 DIODE.ZENR MTZJ5.1B 5.1V SW304 VV020300 SW.TACT SKQNAA
Z D6 VR253700 DIODE.BRG S1NB20 1A 200V SW305 VV020300 SW.TACT SKQNAA
D10 VG437700 DIODE.ZENR MTZJ5.6B 5.6V SW306 VV020300 SW.TACT SKQNAA
Z* D11 V8911600 DIODE DIN60-4084 Z SW501 VG388100 VOLT.SELCT HXW0244-01-080 R
D12 VG437700 DIODE.ZENR MTZJ5.6B 5.6V Z T401 XN394A00 TRANS.PWR R
D13 VG443300 DIODE.ZENR MTZJ30B 30V Z T401 XN393A00 TRANS.PWR BG
Z* D14 V8911600 DIODE DIN60-4084 V301 V3618100 FL.DSPLY 14-BT-56GN
D101 VD631600 DIODE 1SS133,176 XL101 VJ719800 RSNR.CRYS 16.9344MHz
D102 VD631600 DIODE 1SS133,176 XL102 VU763600 RSNR.CE 5MHz
D103 VD631600 DIODE 1SS133,176 VQ948800 SHEET.FL GD
D104 VD631600 DIODE 1SS133,176 % V3688400 SHEET.FL SI
D105 VD631600 DIODE 1SS133,176 V3747500 SUPRT
D106 VG436700 DIODE.ZENR MTZJ4.3A 4.3V V3747400 SPACER.FL T4x6x18
IC3 XA987A00 IC NJM2068D-D
IC4 XD201A00 IC M5290P
IC101 XZ652A00 IC AN8399SA
IC102 XW915A00 IC MN35511AL
* IC103 X3245A00 IC.CPU UPD78076GF-108-3BA
IC104 XS070A00 IC S-24C01ADP EEPROM
IC105 XA987A00 IC NJM2068D-D
IC301 XR188A00 IC LC75710NE FLD
IC302 XF494A00 IC LB1641
* IC303 XV102A00 IC M56789FP
JK1 V3576300 JACK 2P
L1 GE300610 FER.BEAD BL02RN1-R62T4
Z L401 VU984000 FLTR IE-UU10.5-009
L402 V6660800 FER.CORE F5 T19x10x10
* PJ1 V7720900 JACK.PIN LPR6520-E510M
PN1 V3750100 PIN L=50
Q1 iB054430 TR 2SB544 D,E,F,G
Q2 VK432900 TR 2SD1915F S,T
Q3 VK432900 TR 2SD1915F S,T
Q4 VK432900 TR 2SD1915F S,T
CDX-E400
Q5 VK432900 TR 2SD1915F S,T
Q6 VK432900 TR 2SD1915F S,T
Q7 iA093320 TR 2SA933S Q,R
Q8 VS883300 TR 2SB1565 E,F
Q9 VR510800 TR 2SD2396 J,K
Q10 VP872600 TR 2SA1708 S,T
Q102 VK432900 TR 2SD1915F S,T
R1 HV754100 R.CAR.FP 10 1/4W
Z R44 V2370600 R.FUS 0.47 1/6W
R46 HV755100 R.CAR.FP 100 1/4W
R47 HV755100 R.CAR.FP 100 1/4W
R50 V2370600 R.FUS 0.47 1/6W
R51 HV754100 R.CAR.FP 10 1/4W
R118 VL207800 R.ARRAY RGLE7X473J
R307 HV754100 R.CAR.FP 10 1/4W
* New Parts * New Parts

29
A B C D E
CDX-E400
1 ■ EXPLODED VIEW
R model
152
101 142
150 142
103
2 11 2 (4)
140
12
122
103
3 140
150 146
143
143
2 (3)
145
15
5
144
151
4
106
1-111
2 (2) 2 (1)
1-111
121
120
5
1-103 1-11
1-110
1-102
149
1-101
110
142
142 148
6
1-110
110
1-104
149
142 1-103
148
30
CDX-E400
■ MECHANICAL PARTS
Ref.
No. PART NO. Description Remarks Markets
1-11 MF114100 FLEXIBLE FLAT CABLE 14P 100mm
* 1-101 V8782200 FRONT PANEL SI
* 1-101 V8782300 FRONT PANEL GD
* 1-102 V8782400 SUB PANEL-CDX SI
* 1-102 V8782500 SUB PANEL-CDX GD
* 1-103 V8785200 PANEL/SIDE H100
* 1-104 V8782600 SHEET
1-110 VQ368600 PUSH RIVET P3555-B
1-111 VF617600 PAN HEAD P-TITE SCREW 2.6x8 MFC2BL
* 2 V9356200 P.C.B. ASS'Y GD:MAIN R
* 2 V9356300 P.C.B. ASS'Y GD:MAIN GB
5 VZ573200 CD MECHANISM UNIT KSL-2130CCM
Z 11 VZ542500 POWER CABLE 2m R
Z* 11 V9293600 POWER CABLE 2m G
Z 11 VV437300 POWER CABLE 2m B
12 V2438700 CORD STOPPER 10P1
* 15 V8835000 SUMI-CARD C&C 16P 100mm P=1.00
101 V7127300 TOP COVER SI
101 V7127400 TOP COVER GD
* 103 V8783000 REAR PANEL R
* 103 V8783200 REAR PANEL G
* 103 V8783100 REAR PANEL B
* 106 V8782700 LID, CD SI
* 106 V8782800 LID, CD GD
110 V3688500 LEG M0080-M0
120 VR264400 SPACER H8
121 VQ390100 DAMPER 8x8x15
122 VP857700 DAMPER 4x6x5
140 VN413300 BIND HEAD BONDING B-T. SCREW 3x8 MFZN2BL
142 EP600830 BIND HEAD B-TITE SCREW 3x8 MFC2BL
143 EP600250 BIND HEAD B-TITE SCREW 3x8 MFZN2Y
144 VT669300 PW HEAD B-TITE SCREW 3x8-8 MFC2
145 VT669400 PW HEAD B-TITE SCREW 3x15-8 MFC2
146 V2728500 BIND HEAD S-TITE SCREW 4x7 MFZN2BL
148 EL300650 PW HEAD B-TITE SCREW 3x8-8 MFC2BL
149 EP600790 FLAT HEAD B-TITE SCREW 3x8 MFZN2BL
150 VY712800 PW HEAD B-TITE SCREW 3x8-8 MFNI33
151 EP630210 BIND HEAD S-TITE SCREW 3x6 MFZN2BL
CDX-E400
152 EG330030 BIND HEAD SCREW 3x6 MFC2BL R
% V3688400 SHEET, FL SI SI
* New Parts
% : Note on the Main PCB

Of the main PCB part Nos., only the gold (GD) type part Nos. are included in the table. (G, B models)
The only different part between the silver (SI) and gold (GD) type parts is the sheet/FL that is attached to the
fluorescent character display tube. When a SI type main PCB becomes necessary, order a GD type main PCB and a
SI type sheet/FL (V3688400) and replace the sheet/FL of the GD type main PCB with the SI type sheet/FL.
31
A B C D E
CDX-E400
1 ■ EXPLODED VIEW (CD Mechanism Unit)
Stopper
* The stopper is not supplied with the tray as a spare part.

7 When replacing the tray, keep the removed stopper and reuse it.
Should it be lost and a new one be necessary, order service part !8 Main Chassis (S) and remove the stopper
only from it and use it as a spare part.
32
CDX-E400
■ MECHANICAL PARTS (CD Mechanism Unit)
Ref.
VZ573200 CD MECHANISM UNIT KSL-2130CCM
1 CX680620 TRAY (C) 2130 264629001
3 CX675250 GEAR COVER (S) 262554401
4 CX675210 TRAY GEAR (S) 262553501
5 AX619150 CHUCKING PLATE (S) 262554601
6 EX602890 BW HEAD P-TITE SCREW 2.6x7 262629401
7 BX602660 CHUCKING YOKE (S) 262553701
8 NX610570 MAGNET ASS'Y 145249321
9 CX675240 DAMPER (S) 262554102
10 NX636010 CHUCKING PULLEY 264629101
11 AX624650 SUB CHASSIS ASS'Y (S) 264628801
12 AX624640 COIL, SPRING (F) 264723601
13 AX624630 COIL, SPRING (R) 262723501
14 AX624660 WASHER 2130 264628901
15 EX604270 P-TITE SCREW 2.6x10 768513511
16 AX624620 INSULATOR 262723401
18 AX619160 MAIN CHASSIS (S), OUTSERT 262555206
19 VH554700 BW HEAD P-TITE SCREW 2.6x16 331950151
20 CX675270 DRIVE GEAR (S) 262554701
21 CX675260 CONTROL CAM (S) 262554504
22 KX604780 LEAF SWITCH 169266711
23 LX608390 CONNECTOR PIN 5P 156472111
24 NX613050 PWB, LOADIND (S) 164052311
25 JX601470 LOADING MOTOR ASS'Y X26251171
26 CX675200 CENTER GEAR (S) 262527402
27 CX675220 LOADING PULLEY (S) 262553602
28 CX610840 BELT, LOADING MOTOR 365338700
29 EX602880 SCREW 2.6x2.5 262527901
CDX-E400
* New Parts
33
A B C D E
CDX-E400
1 ■ EXPLODED VIEW (Drive Unit)

Note : The parts marked with an asterisk (*) are not available separately. Cover
Ref.
Z 1 NX635420 MOTOR CHASSIS ASS'Y (MB) X26258771
6 2 CX679710 MOTOR GEAR ASS'Y X26257691
3 AX623980 SLED SHAFT 262690801
4 CX679720 GEAR, A (S) 262690701
5 EA020036 PAN HEAD SCREW 2x3 ZMC2-Y 762125515
6 KX604660 LEAF SWITCH 157208511
7 NX613040 PWB, MOTOR MOTOR 6P 163967812
8 LX610120 CONNECTOR PIN 6P 156472211
9 CX680030 GEAR 262700301
10 NX636020 OPTICAL HEAD KSM213C
7
* New Parts
34
CDX-E400
Parts List for Carbon Resistors

Value 1/4W Type Part No. 1/6W Type Part No. Value 1/4W Type Part No. 1/6W Type Part No.
1.0 Ω HJ35 3100 HF85 3100 10 kΩ HF45 7100 HF45 7100
1.8 Ω HJ35 3180 ❊ 11 kΩ HF45 7110 HF45 7110
2.2 Ω HJ35 3220 HF85 3220 12 kΩ HJ35 7120 HF85 7120
3.3 Ω HJ35 3330 HF85 3330 13 kΩ HF45 7130 HF45 7130
4.7 Ω HJ35 3470 HF85 3470 15 kΩ HF45 7150 HF45 7150
5.6 Ω HJ35 3560 HF85 3560 18 kΩ HF45 7180 HF45 7180
10 Ω HF45 4100 HF45 4100 22 kΩ HF45 7220 HF45 7220
15 Ω HJ35 4150 HF85 4150 24 kΩ HF45 7240 HF45 7240
22 Ω HF45 4220 HF45 4220 27 kΩ HJ35 7270 HF85 7270
27 Ω HJ35 4270 HF85 4270 30 kΩ HF45 7300 HF45 7300
33 Ω HF45 4330 HF45 4330 33 kΩ HF45 7330 HF45 7330
39 Ω HJ35 4470 HF85 4390 36 kΩ HF45 7360 HF45 7360
47 Ω HF45 4470 HF45 4470 39 kΩ HF45 7390 HF45 7390
56 Ω HF45 4560 HF45 4560 47 kΩ HF45 7470 HF45 7470
68 Ω HF45 4680 HF45 4680 51 kΩ HF45 7510 HF45 7510
75 Ω HF45 4750 HF45 4750 56 kΩ HF45 7560 HF45 7560
82 Ω HF45 4820 HF45 4820 62 kΩ HF45 7620 HF45 7620
91 Ω HF45 4910 HF45 4910 68 kΩ HF45 7680 HF45 7680
100 Ω HF45 5100 HF45 5100 82 kΩ HF45 7820 HF45 7820
110 Ω HJ35 5110 HF85 5110 91 kΩ HF45 7910 HF45 7910
120 Ω HF45 5120 HF45 5120 100 kΩ HF45 8100 HF45 8100
150 Ω HF45 5150 HF45 5150 110 kΩ HF45 8110 HF45 8110
160 Ω HJ35 5160 ❊ 120 kΩ HF45 8120 HF45 8120
180 Ω HF45 5180 HF45 5180 150 kΩ HF45 8150 HF45 8150
200 Ω HF45 5200 HF45 5200 180 kΩ HF45 8180 HF45 8180
220 Ω HF45 5220 HF45 5220 220 kΩ HJ35 8220 HF85 8220
270 Ω HF45 5270 HF45 5270 270 kΩ HF45 8270 HF45 8270
330 Ω HF45 5330 HF45 5330 300 kΩ HF45 8300 HF45 8300
390 Ω HF45 5390 HF45 5390 330 kΩ HF45 8330 HF45 8330
430 Ω HF45 5430 HF45 5430 390 kΩ HJ35 8390 HF85 8390
470 Ω HF45 5470 HF45 5470 470 kΩ HF45 8470 HF45 8470
510 Ω HF45 5510 HF45 5510 560 kΩ HJ35 8560 HF85 8560
560 Ω HF45 5560 HF45 5560 680 kΩ HJ35 8680 HF85 8680
680 Ω HF45 5680 HF45 5680 820 kΩ HJ35 8820 HF85 8820
820 Ω HF45 5820 HF45 5820 1.0 MΩ HF45 9100 HF45 9100
910 Ω HF45 5910 HF45 5910 1.2 MΩ HJ35 9120 ❊
1.0 kΩ HF45 6100 HF45 6100 1.5 MΩ HJ35 9150 HF85 9150
1.2 kΩ HF45 6120 HF45 6120 1.8 MΩ HJ35 9180 HF85 9180
1.5 kΩ HF45 6150 HF45 6150 2.2 MΩ HJ35 9220 HF85 9220
CDX-E400
1.8 kΩ HF45 6180 HF45 6180 3.3 MΩ HJ35 9330 HF85 9330
2.0 kΩ HJ35 6200 HF85 6200 3.9 MΩ HJ35 9390 ❊
2.2 kΩ HF45 6220 HF45 6220 4.7 MΩ HJ35 9470 HF85 9470
2.4 kΩ HJ35 6240 HF85 6240
2.7 kΩ HF45 6270 HF45 6270
3.0 kΩ HF45 6300 HF45 6300
1/4W Type
3.3 kΩ HF45 6330 HF45 6330
HF45
3.6 kΩ HJ35 6360 HF85 6360 1/4W Type
1/6W Type
3.9 kΩ HF45 6390 HF45 6390 HJ35
HF85
4.7 kΩ HF45 6470 HF45 6470 10mm
5mm
5.1 kΩ HF45 6510 HF45 6510
5.6 kΩ HF45 6560 HF45 6560
6.8 kΩ HF45 6680 HF45 6680
8.2 kΩ HF45 6820 HF45 6820
9.1 kΩ HF45 6910 HF45 6910
1992
35
CDX-E400
CDX-E400

Yamaha CDX E400

Uploaded by

Copyright:

Available Formats

Yamaha CDX E400

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Yamaha CDX E400

Uploaded by

Copyright:

Available Formats

MINI COMPONENT SYSTEM CRX-E400

CDX-E400 SERVICE MANUAL

For the system operation, please refer

Downloaded from www.Manualslib.com manuals search engine

2. Leakage Current Measurement (For 120V Models Only)

● Leakage current must not exceed 0.5mA.

● Be sure to test for leakage with the AC plug in both

WARNING: CHEMICAL CONTENT NOTICE!

WARNING: Laser Safety

Laser Emitting conditions:

Laser Diode Properties

VARO! : AVATTAESSA JA SUOJALUKITUS OHITETTAESSA OLET ALTTIINA NÄKYMÄTTÖMÄLLE

■ PREVENTION OF ELECTRO STATIC DISCHARGE

1. Grounding for electrostatic damage prevention

2. Human body grounding

Anti-static wrist strip

2. Handling of the optical pickup

3. Handling Precautions for the CD mechanism Unit (Optical Pickup)

q MAIN (3) P.C.B.

■ DISASSEMBLY PROCEDURES (Remove parts in disassembly order as numbered.)

1. Removal of Top Cover

4. Removal of Tray Unit Stopper Pin

5. Removal of Pick-up Head o

Pick-up Head Gear A

Check that the disc table height is as specified below.

■ STANDARD OPERATION CHART

POWER ON If a disc is not loaded, “– –:– –” appears in the time indicator.

Press OPEN/CLOSE key. “ OPEN ” appears in the indicator.

Clamp down operation

Tray open Stop after detection of LOADING switch.

Press PLAY key or push the tray.

Tray closed Proceeds to next step after detection of LOADING switch.

Disc mechanism unit clamped up.

Tracking offset auto ADJ

Laser ON LSON = “L” (IC101, 2 pin)

Focus offset auto ADJ

Focus gain rough ADJ

Focus search operation

Focus lock servo ON FLOCK = “H” → “L” (IC102, 11 pin)

Spindle motor accelerated.

Tracking servo ON TLOCK = “H” → “L” (IC102, 12 pin) CDX-E400

Tracking gain rough ADJ

Tracking balance ADJ (only tray OPEN/CLOSE)

Focus balance ADJ

Focus gain ADJ

Tracking gain ADJ

* TOC READ ~ * Data fetch cycle ~

TRACK NO. “1” is searched.

Set to SEARCH by means of Y, T key.

MUTE ON : MUTE ON = “L” → “H” (Q7 Collector)

Press the STOP key.

MUTE ON : MUTE ON = “L” → “H” (Q7 Collector)

Spindle motor stop

Laser OFF : LSOFF = “L” → “H” (IC101, 2 pin)

Forced feed return : FLSW (IC103, 21 pin) = “L”

● Test Mode Function List of Panel keys

Sample of display of test command

Command No. Command Name

The functions corresponded to the test command numbers are as follows.