Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd Logo
Upload

Welcome to Scribd!

  • 1K views

    RSTA Muzzle Brake / Flash Suppressor Mount Installation Manual

    Uploaded by

    Griffin Armament Suppressors
    RSTA Muzzle Brake / Flash Suppressor Mount Installation manual. Download for best resolution! Share it if you like it!

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as PDF, TXT or read online from Scribd

    RSTA Muzzle Brake / Flash Suppressor Mount Installation Manual

    Uploaded by

    Griffin Armament Suppressors
    1K views2 pages
    RSTA Muzzle Brake / Flash Suppressor Mount Installation manual. Download for best resolution! Share it if you like it!

    Copyright

    © Attribution Non-Commercial (BY-NC)

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    RSTA Muzzle Brake / Flash Suppressor Mount Installation manual. Download for best resolution! Share it if you like it!

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    1K views2 pages

    RSTA Muzzle Brake / Flash Suppressor Mount Installation Manual

    Uploaded by

    Griffin Armament Suppressors
    RSTA Muzzle Brake / Flash Suppressor Mount Installation manual. Download for best resolution! Share it if you like it!

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    You are on page 1of 2

    the factory. In this event you may have to have the barrel re-threaded for suppressor use.

    We recommend ADCO firearms in Sylvania Ohio for suppressor thread work. They are located on the internet at www.adcofirearms.com

    TM- RSTA
    Muzzle Brake & Flash Suppressor

    WARNING: FAILURE TO READ AND UNDERSTAND THIS MANUAL PRIOR TO USE MAY RESULT IN INJURY OR DAMAGE TO PROPERTY

    WWW.GRIFFINARMAMENT.COM
    Page 4

    Griffin Armament / Hearing Protection LLC.


    Page 1

    BARREL DIMENSIONS REQUIRED:


    5.56mm RSTA muzzle accessories require 1/2x28 .630 length barrel threads with no greater than .12 of thread runout near the thread shoulder, or that have been relieved with a grooving tool so that there is no thread interfering material more than .12 from the thread shoulder. 7.62mm RSTA muzzle accessories require 5/8x24 .630 length barrel threads with no greater than .12 of thread runout near the thread shoulder, or that have been relieved with a grooving tool so that there is no thread interfering material more than .12 from the thread shoulder. Both thread patterns require a barrels profile to be no greater than .775 outside diameter 2.55 rear of the forward most surface of the barrels muzzle and concentric to the barrel thread, for compatibility with mounts. A drawing is provided in the RSTA suppressor manual.

    on a 1/2x28 thread, and QTY 4-5) .002 shims which will adjust ~1/20th rotation on 5/8x24 threads, or ~1/17th rotation on 1/2x28 threads. 9. Use the minimum quantity of washer shims necessary to create proper timing conditions for acceptable mounting torque to be generated prior to deriving appropriate device timing. It is recommended to put any .010 shims in front of .002 shims to protect them from wrinkling or damage.

    RSTA MUZZLE ACCESSORY INSTALLATION INSTRUCTIONS:


    1. Unload your weapon in accordance with its manufacturers user manual. 2. Remove the bolt or bolt carrier group and charging handle from the weapon. 3. Fixture the weapon in a vise using a polymer vise block. 4. Remove the existing muzzle accessory or thread protector. 5. Remove the existing peel or crush washer (do not re-use). 6. Clean barrel threads and barrel thread shoulder. 7. Remove brake or flash suppressor from packaging and install. If flash suppressor, proceed to step 10. If brake tightens to the ten oclock position, proceed to step 10. If Brake does not time properly, proceed to step 8. 8. Muzzle brake mounting only- remove washer shims from packaging- you are provided QTY 4) .01 thick washers which will adjust timing turn on a 5/8x24 thread or ~1/3 of a turn
    Page 2

    10. Tighten the compensator to approximately 30 foot lbs, or about 1.5(5/8x24) to 2-3(1/2x28) o-clock positions from hand tight to the wrench-tightened and timed configuration. If the compensator is not a timed properly, add or delete washer shims as necessary to obtain proper timing. 11. If you have a suppressor to mount to the muzzle accessory, do so at this time, visually confirm alignment by placing white paper in the breach, and looking through the suppressor bore, parallel to the walls of the barrel bore on all sides, comparing clearance to elements of the suppressor bore. 12. In some cases alignment may be obviously out of true, due to production barrel thread inadequacies. If alignment is not perfect, it is probable that your barrel thread was bad from
    Page 3

    You might also like