Utilizing Pro Dash Inputs in TunerStudio

Utilizing Pro Dash
Inputs in TunerStudio
Table of Contents
TunerStudio CAN Parameters Setup & Configuration ................................................................................ 3

Sensor Input Configuration ...................................................................................................................... 3
Digital Input Configuration ...................................................................................................................... 4
PWM Inputs .............................................................................................................................................. 5
Action Management..................................................................................................................................... 7
Single Input Trigger .................................................................................................................................. 8
Multi Input Trigger ................................................................................................................................... 9
Custom Output Channel Examples ............................................................................................................ 10
Persistent Trip Meter ............................................................................................................................. 10
TunerStudio CAN Parameters Setup & Configuration
These instructions are necessary steps for setup and configuration in TunerStudio for usage of the ADC Inputs
from your Pro Dash or Pro Expansion Module within Vehicle Project.
Sensor Input Configuration
MS3 Steps:
1. Open CAN-bus/Testmodes tab at the top-right in TunerStudio
2. Go to CAN Parameters
3. Enable – “Enable ADC Polling” (Highlighted in diagram below)
4. Setup “CAN ADC selection” (Highlighted in diagram below)
a. CAN id = 4
b. Table = 7
c. Offset
i. 1-4 = 2
ii. 5-8 = 10
Digital Input Configuration
MS3 Steps:
1. Open CAN-bus/Testmodes tab at the top-right in TunerStudio
2. Go to CAN Parameters
3. Enable – “Enable Input Port” (Highlighted in diagram below)
4. Setup “Digital ports”
a. Remote CAN Id = 4
b. Table = 7
c. Offset(bytes)
i. 47 = Dash’s before 2/1/23
ii. 39 = Dash’s after 2/1/23
PWM Inputs
ProDash PWM Input Settings Steps:

1. Open Pro Dash Setup
2. Go to PWM Input settings
3. Set PWM Timer to “32 bit” (Highlighted in diagram below)
4. Set “Stall threshold” to give a zero value with low pulse count
a. Value of 30 suggested to start
ProDash Base I/O Settings Steps:

1. Open Pro Dash Setup
2. Go to Base I/O settings
3. Set timer prescale to 1 and divider to 0
MS3 Steps:
- Open CAN-bus/Testmodes tab at the top-right in TunerStudio
o Go to CAN Parameters
o Enable – “Enable PWM Polling”
i. CAN id = 4
ii. Table for PWM Data = 7
iii. Remote Table Offset For PWM Data = 28
1. PWM 1 Offset = 28
2. PWM 2 Offset = 30 for 16 bit and 32 for 32 bit
iv. Remote Prescale = 1
v. Remote Divider = 0
Action Management
This feature is only available in TunerStudio Ultra, so if you are using the standard MS version you will
need to upgrade your registration to take advantage of this ability.
This feature can be used to take one of the Pro Dash Digital Inputs to trigger an action within TunerStudio.
These are typically wired to a momentary push button and triggered on a short or long push of the button.
Examples:
• Change Dashboard
• Reset Trip Meter
• Start/Stop Datalog
Action Triggers = how you want the Action to be triggered
Users Actions = what you would like to happen in TunerStudio

Single Input Trigger
A single input trigger is if you have only ONE DIGITAL INPUT ACTIVE at one time
The Digital Inputs status:
• Not active = 1 Trigger Name: CANT HAVE SPACES

• Active = 0
Digital Input Variable

Example: You wire Digital Input 4 to a push button
• Digital 1 = canin1_8AND1_OC
• Digital 5 = canin1_8AND 16_OC
Trigger Action When
• Use “Simple” and then choose the appropriate Digital Input Variable that it wired to the push button
Reset Condition
• Simple – this is for momentary push button

• Reset After – this is for a Press and HOLD option which you select the number of seconds to hold the
button
Multi Input Trigger
A multi input trigger is if you have MULTIPLE DIGITAL INPUTS ACTIVE at the same time
Total Digital Input Not Active = 127

Math Example: Digital 4 and Digital 5 Active for Trigger Action
Digital Input Values
Digital Inputs 4&5 Active = (Digital 4) 8 + (Digital 5) 16 = 24
• Digital 1 = 1
127 = Total Digital Input Not Active
• Digital 2 = 2 127
• Digital 3 = 4 24 = Both Digital Inputs Active
• Digital 4 = 8
103 = Total Digital Input with Digital 4&5 Active
-24
• Digital 5 = 16
• Digital 6 = 32 103
• Digital 7 = 64
Trigger Name: CANT HAVE SPACES
Example:
Condition: Digital 4 & 5 Inputs Active to Trigger the Reset Trip Meter action
Reset: resets after time delay of 5 seconds

Custom Output Channel Examples
How to create a Custom Channel
Persistent Trip Meter

Persistent = saves the current value and doesn’t reset the value after shutdown of TunerStudio

Utilizing Pro Dash Inputs in TunerStudio

Uploaded by

Copyright:

Available Formats

Utilizing Pro Dash Inputs in TunerStudio

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Utilizing Pro Dash Inputs in TunerStudio

Uploaded by

Copyright:

Available Formats

Utilizing Pro Dash

TunerStudio CAN Parameters Setup & Configuration ................................................................................ 3

Sensor Input Configuration

ProDash PWM Input Settings Steps:

ProDash Base I/O Settings Steps:

Action Triggers = how you want the Action to be triggered

Users Actions = what you would like to happen in TunerStudio

The Digital Inputs status:

• Not active = 1 Trigger Name: CANT HAVE SPACES

Digital Input Variable

Trigger Action When

• Simple – this is for momentary push button

Total Digital Input Not Active = 127

Trigger Name: CANT HAVE SPACES

Reset: resets after time delay of 5 seconds

How to create a Custom Channel

Persistent Trip Meter

You might also like