BJT Fabrication
BJT Fabrication
This article is indeed about the fabrication of transistors, but also aims to show how the development of fabrication technology proceeded from the very first transistor in logical stages, and enabled various technologies to develop into practical applications that have influenced electronic circuit design right up to the present day. Broadly speaking, there are two dominant types of semiconductor amplifying device, the bipolar junction transistor, and the field effect transistor. Beyond the fundamental devices, they have been developed into a variety of different implementations and have been integrated onto semiconductor chips with ever increasing densities. The key to understanding all of this is to understand how the basic bipolar and field effect device were created.
Although other types of transistor exist, such as the unijunction, the triac, and the IGBT, the BJT and FET account for most applications, and form a basis for understanding the more exotic varieties. For further reading, see: Bipolar Junctions: The basics of PN junctions and bipolar junction transistors
Turn the diagram around, and you can see where the transistor circuit symbol comes from:
The germanium crystal is N-type. A thin P-type layer is formed on the surface, by suitable surface treatment (Sometimes, a surface effect exists on an N-type crystal where a P-type layer forms spontaneously, which allowed P-N junction effects to be observed in experiments even without deliberately forming a P-type layer). Assume no bias connection to the emitter for the time being, and consider the collector is biased in the reverse direction (negative), which supplies electrons to recombine with all the holes under the collector (effectively "collecting" the holes). After recombination, there are no free charge carriers under the collector, so no current can flow. If we now bias the emitter in the forward direction (positive), any available electrons flow out of the emitter, effectively injecting holes into the surface layer of the crystal, augmenting the P-type layer under the emitter. This layer conducts as the holes are the natural current-carriers here. Having said that no current can flow via the reverse-biased collector, now that the emitter is injecting holes nearby, the electric field set up by the collector causes holes to flow to the collector, and this results in an amplified signal in the collector circuit. Unlike junction transistors, the point-contact transistor could have a current gain greater than one, presumably because further current could flow from base to collector. To attempt to gain a better understanding of how the holes introduced at the emitter contact caused an amplified current to flow to the collector, Shockley devised the junction transistor configuration, simply a sandwich of P-N-P or N-P-N layers, where the transistor action could be made to work in in the bulk of the semiconductor, and so the
junction transistor was born, which is the predominant type of bipolar transistor today, the point-contact transistor not being very useful for practical purposes.
From around 1955 to the 1970s, a range of germanium alloy junction transistors manufactured by Philips in Holland became popular, and very well-known to the electronics engineers of the period, in particular the OC70 and OC71 (audio frequency), the OC72, OC78 and OC81 (audio output), and OC44 and OC45 (radio frequency, albeit to much lower frequencies than many contemporary "low frequency" transistors). The OC71 could handle a 50mW power dissipation, Vce(max) of 20 V, and Ic(max) of 10 mA, and had a DC current gain (HFE) between 30 and 75. These were manufactured by slicing up zone-refined and antimony-doped monocrystalline germanium ingots (N-type) into wafers of about 0.5 mm thickness, which were then further polished and diced into chips of about 2.4 mm square (1.5 mm diameter circular chips were machined for the OC44 and OC45). After dicing, the pieces were further thinned by chemical etching down to 0.1 mm. Small indium pellets were fused to the germanium chips in a furnace, with temperature and exposure time closely controlled to determine the depth to which the indium alloys with the germanium chip. Each transistor chip was mounted to its lead wires by a person working with a microscope to bond the lead wires to the collector, base and emitter, and the transistors were sealed in a glass capsule about 15mm long and 6mm in diameter, which had to be filled with a silicone compound to conduct heat from the chip to the case, and painted to prevent light exposure, as the devices were quite photosensitive. The circular RF types had a ring metallisation contact for the base electrode, which enhanced high-frequency performance as it minimises the parasitic base resistance. For further info: "Manufacture of Junction Transistors" Outlook brochure, Mullard, January 1961 (via J.Evans: Valve and Transistor Techie Page) The alloy junction transistor was improved on in the mid 1950s by Herbert Kroemer at RCA labs, who developed a transistor whose impurity concentrations in the base wafer varied, with a high impurity concentration near the emitter, and a low concentration near the collector (similar to "double-diffused" transistors), which created a built-in "driftfield" that improved the high-frequency performance an order of magnitude over alloyjunction devices, and these were known as "alloy-drift", "diffused-alloy" or "drift" transistors. The RCA 2N247 was an example of this type. Kroemer (with others) received the Nobel Prize in Physics in 2000 for his work on semiconductor heterostructures.
Various Transistors On the left is a PCF802 valve for comparison, which contains a triode and a pentode, designed for line timebase oscillators in televisions, and a type in common use in the 1960s. The size advantage of transistors - even for the larger early types - should be obvious. The transistors shown, from left to right, are:
Fabricatio Materi n al Alloy-drift type (made by Telefunke n) similar ASZ20 to the Ge AF114AF118 and OC169OC170 types AlloyAC113 Ge junction AlloyAC134 Ge junction AC127 AlloyGe junction, Part
HFE
PNP
TO-7 15V
40V
25mA
110m 40MHz W
32V
80mA 0.5A -
0.34W 2.5MH 50 z
equiv: 2SB405, ECG158 AlloyOC42 Ge junction AlloyOC44 Ge junction Alloyjunction. Symmetric OC140 Ge al switching transistor OC205 AlloyGe (2 off) junction BC108 Planar epitaxial Si
PNP PNP
15V 12V
NPN
TO-1 glass
20V
0.2A
60mW
4.5MH 50 z
PNP NPN
Si
NPN
60V 30V
0.25A -
100m 300m 150MH 110A W z min. 800 200m 625m 300MH 100A W z min. 300
60V
I will describe the electrical behaviour of the junction transistor in terms of the common base configuration, for comparison with the point contact version. When connected with the base grounded, current flow into the emitter passes into the base, and mostly diffuses to the collector under the attractive field of a reverse bias voltage, with a small proportion of electron flow leaving via the base (i.e. a small conventional current flow into the base). The gain exhibited by this device comes from energy supplied by the collector bias voltage. Although the electron flow injected into the emitter is slightly higher than the flow leaving the collector, the voltage swing of an AC signal is considerably larger at the collector. Another way of looking at it is that the forward-biased emitter-base junction has a low AC resistance, while the reverse-biased collector junction has a high AC resistance, and with a similar current on both sides, the AC voltage must be higher on the collector side. This was a kind of transfer of resistance effect (transresistance), and it suggested the name for the transistor, named by John Pierce of Bell Labs in 1948.
existing N-type into P-type (or vice-versa) by providing more sources of holes than electrons. The diffusion process can create very thin, well-controlled layers, which is highly desirable for creating base regions for high gain and high speed response in circuit applications. It can create a thin epitaxial layer of lightly doped semiconductor on the surface of an intrinsic semiconductor chip, in which the various other N-type or P-type structures can be diffused by further operations. One of the first applications of planar diffusion was used to create the mesa transistor (named after a broad flat-topped hill with cliff-like sides common in the south-west United States), which improved considerably on the alloyed-junction transistor:
In the mesa transistor, the diffusion process has been used to create the base layer, and a central emitter region created by either alloying in an emitter, or diffusing in another layer of opposite type to the base layer, and making a contact to it. The base contact is made by a ring of metallisation (note the similarity to the high-frequency alloy-junction base contact), shown by the dotted line. To precisely define the area of the transistor, and avoid excessive parasitic capacitance, the semiconductor chip is selectively etched, using a photomasking process, around the base contact ring to isolate the active area in the shape of a mesa. The transistor chip is mounted on a metal surface to make contact with the collector and provide an efficient heat sink. The improved thermal bonding of the mesa chip to the case compared with the alloy-junction type, and the use of silicon rather than germanium (which has lower leakage current at high temperature) enabled the devices to dissipate higher powers and have higher current ratings, for example, the early 2N497 device was rated at 200 mA collector current and 4W power dissipation. Examples of mesa transistors include the 2N497, 2N696, 2N697, RT409, 2N706c, 2N834, 2N1131, 2N1132, 2SA161 (Ge) and 2SC41. The first diffused-base germanium mesa transistor was created in 1954 by Charles A. Lee at Bell Labs, which had a cutoff frequency of 500 MHz. This was another order of
magnitude improvement in the frequency response compared with the alloy-drift transistor.
Stage 1: A chip of N-type semiconductor with a surface layer of silicon oxide (grown by heating the silicon in pure oxygen) has a window of oxide etched out photolithographically. This requires a layer of light-sensitive material to be coated on the silicon, then exposed by projecting an image of a mask on to it, such that the material can be selectively washed away depending on whether the material was exposed to light or not. This creates a photo-resist mask, which allows an etchant solution to be used to etch out the areas that are unmasked. The N-type semiconductor can be a layer diffused into an intrinsic semiconductor chip, which is known as an epitaxial layer. Stage 2: A diffusion process is used to create a region under the window that is P-type, where the impurity atoms have diffused into the silicon. The window is then covered with a new layer of oxide. Stage 3: Another photolithographic window is etched within the area of the previous one.
Stage 4: Then another diffusion process is used, this time creating a layer of N-type semiconductor entirely within the previously created P-type layer. This new layer will be the emitter, and what remains of the P-type layer forms the base. The emitter-forming window is then covered with a new layer of oxide. Stage 5: Photolithographic windows are etched over the base P-type and emitter N-type regions. Stage 6: A layer of aluminium is diffused on to the windowed base P-type and emitter Ntype regions. A similar method is used to make contact with the epitaxial collector layer (not shown), and then very fine wires may be bonded by various techniques to provide connections between the chip and the wires or pins of the package that contains and protects it. A silicon wafer is shown below, containing a number of repeated aluminium metallisation test patterns, which were used to develop a manufacturing process.
A: Silicon wafer (coated with photoresist) B: Area consisting mostly of aluminium metallisation
The planar fabrication process (which, unlike the mesa process, did not need to isolate the parts of the silicon wafer where the transistor was fabricated with an etched trench) enabled multiple transistor structures to be fabricated on the same silicon wafer, and they could if desired be interconnected using the aluminium metallisation layer. This was the great enabling technology for the development of mass-produced integrated circuits.
The planar fabrication process was well suited to the creation of new semiconductor structures, for example, it enabled transistors with multiple emitters, sharing a common collector, to be integrated:
These are electrically equivalent to two BJT transistors connected in parallel, except for the emitters (not to be confused with conventional transistors with multiple emitter leads, which are used to reduce inductance to a single emitter). A current from either emitter injected into the base flows into the collector (minus a small base bias fraction). These structures have an important application in digital logic circuitry, where the emitters can serve as separate inputs to a logic function, as in Transistor-Transistor Logic (TTL), which was first introduced by Texas Instruments in 1962 as the "7400 series", remained popular until the 1990s, and still has important applications (often embedded within custom ICs). Before discussing TTL further, I will briefly digress to mention their immediate predecessor technologies, which were first to be fully integrated. In 1961, US President John F. Kennedy announced a programme for "landing a man on the Moon and returning him safely to the Earth", and the first commercial logic integrated circuits (ICs) were released to the market by Fairchild Camera and Instrument Corp. as the L900 family, representatives of which are still available today: Transistor Museum Fairchild uLogic 923 These devices were an early type of logic gate known as resistor-transistor logic (RTL), which had developed out of circuits that could be conveniently made from discrete resistors and transistors. The first Apollo spacecraft guidance computer used approximately 4100 RTL logic gates.
RTL had poor noise immunity, and limited ability to drive multiple loads (fan-out), so buffer circuits such as this were needed to expand the number of drivable stages, provide isolation, or drive bus lines. Whereas the L914 logic gate had a fan-out of 16, the L900 buffer could increase the fan-out to 80.
The L914 dual two input gate could be used as a NAND or NOR logic function. If either input 1 or 2 were driven high, output 7 would be driven low. When a high voltage represents a logic 1, this is NOR function (inverted version of OR, where the output would be high if either input went high). If negative logic is used, where a low voltage represents a logic 1, both inputs must be low for the output to be high (inverted version of AND, where the output would be low when both inputs are low). The next intermediate stage between RTL and TTL was diode-transistor logic (DTL), which used diodes to perform logic functions (diodes require less space than resistors when integrated) and was somewhat faster. Signetics launched a DTL logic range in 1962, and Fairchild launched their own in 1963, which was cheaper and outsold the Signetics devices. Ferranti produced a logic IC range in Europe in 1961, marketed as Micronor I and aimed at computing for Naval applications, followed by Micronor II, a faster DTL range. DTL had the best speed and reliability characteristics for integrated logic, at least until TTL came along. The following diagram shows an example of DTL from the Texas Instruments SN3900 / SN4500 Series:
The first integrated logic devices were very costly, so were limited to applications where the advantage of integration was essential, such as space exploration. As integrated circuits began to be commercially successful, because of the great benefit of replacing discrete circuits with many transistors, they were often applied to uses well outside their intended application, such as is shown by the following circuit, which was an application of the Ferranti ZSS54A Micronor II triple inverter (a DTL device) as a signal injector for TV servicing, with one stage biased into a linear mode for use as a headphone amplifier. This circuit by A. J. McEvoy appeared in the August 1967 edition of "Practical Television":
Initially, only a few logic gates (up to about 20 gates) could be integrated, so the ability to create a logic function by building it in to the structure of a single transistor itself was a great advantage. One multi-emitter transistor could now do the job of multiple diodes. The multiple-emitter planar transistor structure when used as a logic input could be connected directly to the preceding transistor output driver stage and was faster than the earlier RTL and DTL families, because the resistor elements of the input stages were eliminated, so the capacitance of the input transistor and package capacitance could be charged directly by the driver transistors. This was the Transistor-Transistor Logic (TTL) logic family, introduced in 1964 by Texas Instruments as the 7400 (industrial) and 5400 (military) qualified series. The next circuit shows the input stage of a TTL logic circuit:
If both input A and B are high (close to Vcc voltage), then both base-emitter junctions must be below the forward bias potential, and the base-collector junction of Q1 must be forward biased via the Vcc potential across R1, Q1, D1, R2 and the base-emitter junction of Q2, which is also forward biased. A current flows through this chain, and with Q2 biased into conduction, the voltage at X is low. The circuit is designed so that in this case, the operating point of Q2 brings the collector voltage down to Vce(sat), normally less than 1 Volt. If an emitter input (A or B) is connected to a low input voltage, the Q1 base-emitter junction can become forward biased. The current from R1 into the base can now flow out through the emitter. The voltage at Q1's collector falls, as Q1 is now fully turned on and the collector-emitter voltage difference must be small, and as long as the emitter voltage is low enough, the base-emitter voltage at Q2 falls below forward bias levels, and current through R3 pulls the output X up to near Vcc voltage (as long as the output X is not loaded too heavily). Thus, if A or B is low, or both are low, X is high, and if A and B are both high, then X is low. This is the function of a NAND gate: a logic gate which generates an inversion of the simpler AND function (where the output is high if both inputs are high).
The depletion mode MOSFET was described theoretically in a patent (US1900018) by Julius Edgar Lilienfeld (1881-1963) filed in 1928, based on semiconducting copper sulphide, the conductivity of which is controlled by an aluminium electrode, insulated from the semiconductor by its surface layer of aluminium oxide. There were no practical implementations of this device, as there was no supply of high purity semiconductor material. Shockley had encountered difficulties in creating an amplifying field effect device, and the effort to do so was overshadowed when he obtained better results with the pointcontact and sandwich BJT approach. John Atalla at Bell labs [1] developed the MOSFET field effect transistor in the planar form, similar to that shown below:
The N-channel MOSFET has a drain and a source area consisting of heavily doped Ntype semiconductor. Between the two is a thin layer of N-type material known as the (conduction) channel. Overlaying the channel is the gate electrode, which is insulated from the channel by an oxide layer. The implanted conducting channel was used in the earliest MOSFETs, which were the "depletion mode" variety, in which the device normally conducts fully, so that for an Nchannel device a negative voltage must be applied to the gate to suppress the conduction and reduce the drain current to the nominal operating value (This channel is not present in an "enhancement mode" device, where to enable conduction, the gate must have a positive voltage bias to create an electrically-induced channel). For N-channel MOSFETs, negative gate voltages with respect to the source and substrate will attract holes from the substrate into the channel, which will narrow the channel and increase the channel resistance.
Positive gate voltages with respect to the source and substrate will repel holes from the channel into the substrate, effectively widening the channel and decreasing channel resistance, although normally the channel resistance is low enough at zero-bias for all practical purposes, so that positive gate voltage is not normally required for depletion devices. For P-channel devices, all the polarities mentioned in discussion are reversed. Although conceptually the connection to the substrate is shown in the diagram as an underlying electrode, in practice with planar construction everything is usually implanted into a thin epitaxial layer on the surface of a wafer whose thickness is much greater, relatively speaking, than the thickness of the devices, so there is normally a fabrication process that allows an electrode on the surface to make contact with the P-type substrate. If P-channel MOSFETs are required in the same substrate, the "substrate" for each Pchannel MOSFET then consists of a "well" of N-type material diffused or implanted first into the semiconductor. The electric field generated by the gate modulates the depth of the conducting N-type region of the channel. This is shown in detail below.
With a positive voltage applied to the drain, current flows through the N-type channel. But with a negative voltage on the gate, current carrying electrons in the channel are repelled by the electric field, leaving an insulating depletion region which contains positively charged donor atoms, but no free charge carriers, and hence no current can
flow between source and drain through this region. The higher the negative gate-source bias voltage, the further the depletion region extends into the channel, reducing the crosssectional area available to conduct current. Hence, the FET behaves as a resistance controlled by the gate voltage. Note that the depletion region is pictured with some asymmetry, increasing in width towards the drain. This happens when the drain is biased positive, as is usual with an N-type FET used for anything other than a small-signal variable resistance, and because the effective negative bias on the gate is higher relative to the drain potential, the depletion region is wider at the drain end. If the depletion region is a small fraction of the channel width, a change in drain voltage causes a relatively small change in the conductive area, and so the current increases as if the FET were a resistor. The following diagram shows the situation with an increased gate-source bias, which has increased the depth of the depletion layer until the conducting area is almost eliminated. This point is known as "pinch-off".
If the drain-source voltage is increased when there is a "pinch-off" zone, the increased effective reverse gate bias at the drain end tends to reduce the conduction area significantly, which tends to cancel out the current increase due to increased drain voltage. In other words, the "pinch-off" zone is extended, and the extra voltage drop along its narrow conduction area almost matches the additional drain-source voltage. There is therefore a built-in negative feedback effect which causes the drain voltagecurrent characteristic to flatten out as the drain voltage passes the point at which there is a significant pinch-off zone.
For an N-channel enhancement MOSFET, when the gate-source voltage is zero, the drain-source current is zero. A depletion region is formed around the N-type source and drain regions, because of the recombination of electrons and holes at the junction with the P-type substrate, as in a PN junction diode. A positive voltage applied to the drain reverse-biases the junction there, so no current flows.
If we apply a positive voltage to the gate, above a certain threshold voltage which is around 0.5 to 3 V, the electric field created under the gate electrode repels holes in the Ptype substrate and attracts electron current carriers from the N-type source (and drain, if the drain voltage is low). These electrons can now flow from source to drain when there is a positive drain voltage applied. The electrically-induced channel under the gate is equivalent to a depletion region filled with majority carriers from the source. Although these are minority carriers in the channel, all the current carriers are of the same type, unlike the bipolar NPN or PNP transistor where both holes and electrons are active. The induced channel also resembles an N-type layer although it is really P-type with excess electrons, hence it may be termed an inversion layer as it inverts P to N. Increasing the gate voltage enhances the width of the inversion layer, and requires no built-in channel, and so this is known as an enhancement mode MOSFET. As for P-channel MOSFETs, these work in a similar way except that the N and P type regions, charge carrier types, and bias voltages are all the other way round.
CMOS Technology
Both N-type and P-type enhancement mode MOSFETs may be readily integrated, and if connected as a series pair across a power supply voltage, with the P-channel device source connected to Vdd, and the N-channel device source connected to ground (or Vss) as shown in the inverter below, you will find that if both gates are connected together to Vdd, the P-channel device will be off and the N-channel device will be on, driving the output low, and if both gates are connected together to ground, the P-channel device will be on and the N-channel device will be off. This can be used as a buffer stage, to drive a load from a low-power input, or as a logic level inverter. It is the fundamental basis for complementary MOSFET technology, or CMOS, which has become the dominant logic
technology today (including many derivative forms). Its advantages include a symmetrical voltage transfer function, which aids noise immunity, a high input impedance, which facilitates easy interfacing and high fan-out, a low driving impedance for both a low and a high level output, which supports fast switching, and the basic series pair structure consumes no current except when the stage is actually switching, which enabled low-power applications such as digital wrist-watches.
A CMOS NOR gate is also shown above. If either input A, or B, or both are high, then at least one of the series-connected P-channel MOSFETS Q3 or Q4 must be nonconducting, and at least one of the parallel-connected N-channel MOSFETS Q1 or Q2 must be conducting, so the output X must be pulled low. If both input A and B are low, then both of the series-connected P-channel MOSFETS Q3 or Q4 must be conducting, and both of the parallel-connected N-channel MOSFETS Q1 or Q2 must be non-conducting, so the output X must be pulled high. This implements the logic NOR function (inverted OR). A practical CMOS IC inverter normally uses multiple cascaded stages (at least 3, because two cascaded inverters don't invert) to obtain a sharp transition in the input/output voltage transfer characteristic, and diode-resistor networks on inputs to protect against electrostatic damage. The unbuffered stages in devices like the SGS-Thomson HCC4007U are essentially as shown above, have slightly lower propagation delays, and can be biased into linear operation, for example to implement an oscillator circuit. Buffered logic stages normally have inverter stages added to their inputs and outputs.
Contemporary Developments
How has the fundamental planar epitaxial technology that I have described been advanced for current and future requirements? Here is a shortlist of key developments:
Increasing numbers of layers of implanted semiconductor, insulator, and metallisation More semiconductor materials, e.g. Gallium Arsenide, Gallium Phosphide, Indium Arsenide, Indium Phosphide, Gallium Antimonide, Indium Antimonide, Silicon-Germanium and Silicon Carbide Vertical structures (e.g. VMOS) Polysilicon gates to reduce enhancement mode thresholds, and low-resistivity metal gates to reduce series resistance Chemical vapour deposition (CVD) and plasma vapour deposition (PVD) to deposit a variety of materials Ion implantation, which can introduce impurity elements into precise and small dimensioned features, particularly shallow layers, create structures with doping that increases with depth, and also modify crystal structure Etching by chemical, electrolytic, and plasma techniques Low dielectric constant insulating layers to increase speed Decreasing feature sizes in conjunction with advances in photolithography, and lithography not using light (e.g. electron beams) Photolithography using shorter wavelengths, into the ultra-violet and X-ray spectrum; Deep-Ultraviolet Lithography (DUL) has been in use with everdecreasing wavelengths starting around 1994, Extreme Ultraviolet Lithography (EUVL) prototype equipment exists, and volume production equipment is expected to be in general use around 2007. There are already patents on gammaray lithography. Atomic-layer deposition (ALD), e.g. for gate dielectrics only a few atomic layers thick
Timeline
1939 P-type and N-type semiconductors discovered in silicon at Bell Labs 1947 Shockley, Bardeen and Brattain demonstrate first point contact transistor 1949 Popular Mechanics predicts computers in the future may have only 1000 vacuum tubes and perhaps weigh only 1 1/2 tons 1950 William Shockley's lab demonstrates first junction transistor 1952 Alloy junction transistor 1953 General Electric Company creates the Unijunction transistor 1954 Texas Instruments puts silicon transistors into production 1954 C. A. Lee at Bell Labs makes first diffused-base germanium mesa transistor with a cutoff frequency of 500 MHz 1955 IBM begins marketing its first transistorized computer, model 7090
1956 William Shockley invents the PNPN diode (Shockley diode, two of which, when packaged as a parallel pair connected in opposite directions are known as a DIAC) 1957 General Electric announces their commercial Silicon Controlled Rectifier, also known as the thyristor, which could switch 1000V and several hundred amps 1958 Fairchild Camera and Instrument Corp. market their first silicon diffusion mesa transistors to RCA 1958 Jack Kilby at Texas Instruments demonstrates the first working integrated circuit in the laboratory on September 12th 1959 Planar process invented by Swiss physicist Jean Hoerni 1959 Texas Instruments and Fairchild Camera and Instrument Corp. independently develop the first commercial integrated circuits- Fairchild's version demonstrating the first with planar metallised interconnection. 1960 John Atalla at Bell labs develops the field effect transistor, and epitaxial growth technology for semiconductor crystals begins also at ATT Bell Labs 1961 Fairchild Camera and Instrument Corp. release their first commercial integrated circuit to the market 1961 Ferranti introduces Micronor I Diode-Transistor Logic 1962 Signetics introduces a range of Diode-Transistor Logic 1963 Fairchild introduce the 907 DTL logic gate, which used a mere four bipolar transistors 1963 CMOS logic circuit principles disclosed for the first time in U.S. patent 3,356,858 by Frank Wanlass of Fairchild Semiconductor 1964 Transistor-Transistor Logic introduced by Texas Instruments 1965 Gordon Moore discovers Moore's Law: The number of components on the most complex integrated circuit chip would double each year 1968 RCA introduces their CD4000 series CMOS logic family, which they called "COS/MOS" 1970s Molecular beam epitaxy invented at Bell labs 1971 Intel introduces the 4004 4-bit microprocessor, containing 2300 transistors, and considered to be the world's first single chip microprocessor. It was used on the Pioneer 10 spacecraft in 1972. 1975 Moore's Law slows, towards a doubling at present time about every 2 years 1975 IBM introduces their first "Personal Computer", the IBM 5100, which is considered to be the first portable PC (but not the first PC, which is attributed to the Altair 8800 kit launched by Ed Roberts in January 1975) based on large-scale integration (LSI): a board-level IBM "Palm" microcontroller made up from TTLcompatible 134-gate bipolar gate array technology called "Dutchess", with chips containing 60 three-input NAND gates, 40 four-input NAND gates, and 34 twoinput NOR off-chip drivers, plus assorted TTL devices. 1978 Intel introduces the 8086 processor, which was the basis for all x86compatible CPUs 2006 Intel to ship dual-core Itanium Montecito with 1.75 billion transistors on a chip 2010 Processors expected to reach 10 billion transistors per chip (Patrick Gelsinger, design manager for the 80486, InfoWorld CTO Forum, April 9, 2002)
2010-2015 Gordon Moore expects Moore's Law to slow again 2015-2025 Moore's Law reaches fundamental limitations
Info
Zip file containing Circuit Scribe project files: alloytr.cct - Diagram of alloy junction transistor cosmos.cct - CMOS inverter and NOR gate mosdepl.cct - Diagrams of MOSFET depletion device mosenh.cct - Diagrams of MOSFET enhancement device mosfab.cct - Diagram of MOSFET fabrication planardtl.cct - DTL logic gates planarfab.cct - Diagram of planar fabrication process planarttl.cct - Diagram of multiple-emitter transistor and TTL circuit transistors.cct - Diagrams of point-contact transistor ul900914.cct - uL900 buffer and uL914 dual two-input gate basicfab.zip [36KB] For Circuit Scribe software, see: Software Catalog: Fairchild-uL900-914 (Industrial RTL Micrologic Integrated Circuits (uL900, uL914)) [1] Kahng D, Atalla MM. "Silicon-silicon dioxide field induced surface devices", IREAIEEE Solid-State Device Research Conference, Carnegie Institute of Technology, Pittsburgh, PA, 1960. Copyright All Rights Reserved. No portion of this site may be reproduced in any way without express permission
of the publisher. Home page first created: February 1st, 1996