Professional Documents
Culture Documents
Ua 741
Ua 741
uA741
SLOS094G – NOVEMBER 1970 – REVISED JANUARY 2018
Device Information(1)
PART NUMBER PACKAGE BODY SIZE (NOM)
µA741CD SOIC (8) 4.90 mm × 3.91 mm
µA741CP PDIP (8) 9.81 mm × 6.35 mm
µA741CPS SO (8) 6.20 mm × 5.30 mm
(1) For all available packages, see the orderable addendum at
the end of the data sheet.
Simplified Schematic
OFFSET N1
IN + +
OUT
IN – –
OFFSET N2
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
uA741
SLOS094G – NOVEMBER 1970 – REVISED JANUARY 2018 www.ti.com
Table of Contents
1 Features .................................................................. 1 7.3 Feature Description................................................. 10
2 Applications ........................................................... 1 7.4 Device Functional Modes........................................ 11
3 Description ............................................................. 1 7.5 µA741Y Chip Information........................................ 11
4 Revision History..................................................... 2 8 Application and Implementation ........................ 12
8.1 Application Information............................................ 12
5 Pin Configurations and Functions ....................... 4
8.2 Typical Application .................................................. 12
6 Specifications......................................................... 5
6.1 Absolute Maximum Ratings ...................................... 5 9 Power Supply Recommendations...................... 14
6.2 Recommended Operating Conditions....................... 5 10 Layout................................................................... 14
6.3 Thermal Information .................................................. 5 10.1 Layout Guidelines ................................................. 14
6.4 Electrical Characteristics: μA741C............................ 6 10.2 Layout Example .................................................... 14
6.5 Electrical Characteristics: μA741Y ............................ 7 11 Device and Documentation Support ................. 16
6.6 Switching Characteristics: μA741C ........................... 7 11.1 Receiving Notification of Documentation Updates 16
6.7 Switching Characteristics: μA741Y ........................... 7 11.2 Trademarks ........................................................... 16
6.8 Typical Characteristics .............................................. 8 11.3 Electrostatic Discharge Caution ............................ 16
7 Detailed Description ............................................ 10 11.4 Glossary ................................................................ 16
7.1 Overview ................................................................. 10 12 Mechanical, Packaging, and Orderable
7.2 Functional Block Diagram ....................................... 10 Information ........................................................... 16
4 Revision History
Changes from Revision F (May 2017) to Revision G Page
• Changed supply voltage unit from "°C" to "V" in Absolute Maximum Ratings table ............................................................. 5
• Updated data sheet text to the latest documentation and translation standards .................................................................. 1
• Deleted text regarding µA741M device (obsolete package) from Description section........................................................... 1
• Added µA741CD, µA741CP, and µA741CPS devices to Device Information table .............................................................. 1
• Deleted µA741x device from Device Information table ......................................................................................................... 1
• Updated pinout diagrams and Pin Functions tables in the Pin Configurations and Functions section .................................. 4
• Deleted µA741M pinout drawings information from Pin Configurations and Functions section ............................................ 4
• Deleted Electrical Characteristics: µA741M table from Specifications section ...................................................................... 5
• Added operating junction temperature (TJ) and values to Absolute Maximum Ratings table ............................................... 5
• Deleted text regarding µA741M from Absolute Maximum Ratings table .............................................................................. 5
• Deleted text regarding µA741M device from Recommended Operating Conditions table .................................................... 5
• Deleted Dissipation Ratings table .......................................................................................................................................... 5
• Added Thermal Information table and values ........................................................................................................................ 5
• Deleted µA741M in Switching Characteristics table .............................................................................................................. 7
• Correct typo in Figure 1 ......................................................................................................................................................... 8
• Deleted text regarding µA741M device from Detailed Description section .......................................................................... 10
• Updated text in Overview section ........................................................................................................................................ 10
• Added 2017 copyright to Functional Block Diagram ........................................................................................................... 10
• Added caption to Figure 11 in Device Functional Modes section ........................................................................................ 11
• Changed pins 1 and 5 from "NC" to "Offset N1" and "Offset N2" in Figure 18 .................................................................... 15
• Added Applications, Device Information table, Pin Functions table, ESD Ratings table, Thermal Information table,
Feature Description section, Device Functional Modes, Application and Implementation section, Power Supply
Recommendations section, Layout section, Device and Documentation Support section, and Mechanical,
Packaging, and Orderable Information section. ..................................................................................................................... 1
• Moved Typical Characteristics into Specifications section. ................................................................................................... 8
uA741C D, P, or PS Package
8-Pin SOIC, PDIP, SO
Top View
OFFSET N1 1 8 NC
IN± 2 7 VCC+
IN+ 3 6 OUT
VCC± 4 5 OFFSET N2
Not to scale
Pin Functions
PIN
I/O DESCRIPTION
NAME NO.
IN+ 3 I Noninverting input
IN– 2 I Inverting input
NC 8 — No internal connection
OFFSET N1 1 I External input offset voltage adjustment
OFFSET N2 5 I External input offset voltage adjustment
OUT 6 O Output
VCC+ 7 — Positive supply
VCC– 4 — Negative supply
6 Specifications
6.1 Absolute Maximum Ratings
over virtual junction temperature range (unless otherwise noted) (1)
MIN MAX UNIT
Supply voltage, VCC (2) µA741C –18 18 V
Differential input voltage, VID (3) µA741C –15 15 V
(2) (4)
Input voltage, VI (any input) µA741C –15 15 V
Voltage between offset null (either OFFSET N1 or
µA741C –15 15 V
OFFSET N2) and VCC–
(5)
Duration of output short circuit Unlimited
Continuous total power dissipation See Thermal Information
Case temperature for 60 seconds µA741C N/A N/A °C
Lead temperature 1.6 mm (1/16 inch) from case for 60 seconds µA741C N/A N/A °C
Lead temperature 1.6 mm (1/16 inch) from case for 10
D, P, or PS package µA741C 260 °C
seconds
Operating junction temperature, TJ 150 °C
Storage temperature range, Tstg µA741C –65 150 °C
(1) Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under Recommended Operating
Conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
(2) All voltage values, unless otherwise noted, are with respect to the midpoint between VCC+ and VCC–.
(3) Differential voltages are at IN+ with respect to IN –.
(4) The magnitude of the input voltage must never exceed the magnitude of the supply voltage or 15 V, whichever is less.
(5) The output may be shorted to ground or either power supply.
(1) For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application
report.
(1) All characteristics are measured under open-loop conditions with zero common-mode input voltage unless otherwise specified.
Full range for the µA741C is 0°C to 70°C.
(2) This typical value applies only at frequencies above a few hundred hertz because of the effects of drift and thermal feedback.
(1) This typical value applies only at frequencies above a few hundred hertz because of the effects of drift and thermal feedback.
(2) All characteristics are measured under open-loop conditions with zero common-mode voltage unless otherwise specified.
VI
– OUT
IN
+
0V
INPUT VOLTAGE
WAVEFORM
CL = 100 pF RL = 2 kΩ
TEST CIRCUIT
Figure 1. Rise Time, Overshoot, and Slew Rate
100 400
VCC+ = 15 V
VCC+ = 15 V
90 VCC – = –15 V
350 VCC – = –15 V
I IO – Input Offset Current – nA
60 250
50 200
40
150
30
100
20
50
10
0 0
– 60 – 40 – 20 0 20 40 60 80 100 120 140 – 60 – 40 – 20 0 20 40 60 80 100 120 140
± 11 ±14
±10 ±12
±9 ±10
±8 ±8
±7 ±6
±6 ±4
±5 ±2
±4 0
0.1 0.2 0.4 0.7 1 2 4 7 10 100 1k 10k 100k 1M
RL – Load Resistance – kΩ f – Frequency – Hz
Figure 4. Maximum Output Voltage vs Load Resistance Figure 5. Maximum Peak Output Voltage vs Frequency
80 RL = 2 kΩ
Voltage Amplification – dB
TA = 25°C
70
100
60
50
40 40
30
20
20
10
0
10 –10
0 2 4 6 8 10 12 14 16 18 20 1 10 100 1k 10k 100k 1M 10M
VCC ± – Supply Voltage – V f – Frequency – Hz
Figure 6. Open-Loop Signal Differential Voltage Figure 7. Open-Loop Large-Signal Differential Voltage
Amplification vs Supply Voltage Amplification vs Frequency
100 28
CMRR – Common-Mode Rejection Ratio – dB
VCC+ = 15 V
90 VCC– = –15 V 24
BS = 10 kΩ
80
TA = 25°C
20
VO – Output Voltage – mV
70
90%
16
60
50 12
40 8
30 VCC+ = 15 V
4
VCC– = –15 V
20 10% RL = 2 kΩ
0
10 CL = 100 pF
tr TA = 25°C
0 –4
1 100 10k 1M 100M 0 0.5 1 1.5 2 2.5
f – Frequency – Hz t – Time - µs
Figure 8. Common-Mode Rejection Ratio vs Frequency Figure 9. Output Voltage vs Elapsed Time
8
VCC+ = 15 V
6 VCC– = –15 V
RL = 2 kΩ
CL = 100 pF
Input and Output Voltage – V
4
TA = 25°C
VO
2
0
VI
–2
–4
–6
–8
0 10 20 30 40 50 60 70 80 90
t – Time – ms
Figure 10. Voltage-Follower Large-Signal Pulse Response
7 Detailed Description
7.1 Overview
The μA741 has been a popular operational amplifier for over four decades. Typical open loop gain is 106 dB
while driving a 2000-Ω load. Short circuit tolerance, offset voltage trimming, and unity-gain stability makes the
μA741 useful for many applications.
VCC+
IN –
OUT
IN+
OFFSET N1
OFFSET N2
VCC –
Component Count
Transistors 22
Resistors 11
Diode 1
Capacitor 1 Copyright © 2017, Texas Instruments Incorporated
45
(5)
NOTE
Information in the following applications sections is not part of the TI component
specification, and TI does not warrant its accuracy or completeness. TI’s customers are
responsible for determining suitability of components for their purposes. Customers should
validate and test their design implementation to confirm system functionality.
IN + +
OUT
IN – – OFFSET N2
OFFSET N1
10 kΩ
To VCC –
12 V
VOUT
+
VIN
12 0.045
0.040
10
0.035
0.030
8
0.025
VOUT (V)
IIO (mA)
6 0.020
0.015
4
0.010
0.005
2
0.000
0 ±0.005
0 2 4 6 8 10 12 0 2 4 6 8 10 12
VIN (V) C001 VIN (V) C002
Figure 14. Output Voltage vs Input Voltage Figure 15. Current Drawn Input of Voltage Follower (IIO)
vs Input Voltage
0.45
0.40
0.35
0.30
ICC (mA)
0.25
0.20
0.15
0.10
0.05
0.00
0 2 4 6 8 10 12
VIN (V) C003
CAUTION
Supply voltages larger than ±18 V can permanently damage the device (see Absolute
Maximum Ratings).
10 Layout
11.2 Trademarks
All trademarks are the property of their respective owners.
11.3 Electrostatic Discharge Caution
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
11.4 Glossary
SLYZ022 — TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.
www.ti.com 7-Apr-2024
PACKAGING INFORMATION
Orderable Device Status Package Type Package Pins Package Eco Plan Lead finish/ MSL Peak Temp Op Temp (°C) Device Marking Samples
(1) Drawing Qty (2) Ball material (3) (4/5)
(6)
UA741CP ACTIVE PDIP P 8 50 RoHS & Green NIPDAU N / A for Pkg Type 0 to 70 UA741CP Samples
UA741CPSR ACTIVE SO PS 8 2000 RoHS & Green NIPDAU Level-1-260C-UNLIM 0 to 70 U741 Samples
UA741CPSRE4 ACTIVE SO PS 8 2000 RoHS & Green NIPDAU Level-1-260C-UNLIM 0 to 70 U741 Samples
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based
flame retardants must also meet the <=1000ppm threshold requirement.
(3)
MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead finish/Ball material - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead finish/Ball material values may wrap to two
lines if the finish value exceeds the maximum column width.
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com 7-Apr-2024
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com 10-Jan-2024
B0 W
Reel
Diameter
Cavity A0
A0 Dimension designed to accommodate the component width
B0 Dimension designed to accommodate the component length
K0 Dimension designed to accommodate the component thickness
W Overall width of the carrier tape
P1 Pitch between successive cavity centers
Sprocket Holes
Q1 Q2 Q1 Q2
Pocket Quadrants
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com 10-Jan-2024
Width (mm)
H
W
Pack Materials-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com 10-Jan-2024
TUBE
T - Tube
height L - Tube length
W - Tube
width
Pack Materials-Page 3
PACKAGE OUTLINE
D0008A SCALE 2.800
SOIC - 1.75 mm max height
SMALL OUTLINE INTEGRATED CIRCUIT
SEATING PLANE
.228-.244 TYP
[5.80-6.19]
.004 [0.1] C
A PIN 1 ID AREA
6X .050
[1.27]
8
1
.189-.197 2X
[4.81-5.00] .150
NOTE 3 [3.81]
4X (0 -15 )
4
5
8X .012-.020
B .150-.157 [0.31-0.51]
.069 MAX
[3.81-3.98] .010 [0.25] C A B [1.75]
NOTE 4
.005-.010 TYP
[0.13-0.25]
4X (0 -15 )
SEE DETAIL A
.010
[0.25]
.004-.010
0 -8 [0.11-0.25]
.016-.050
[0.41-1.27] DETAIL A
(.041) TYPICAL
[1.04]
4214825/C 02/2019
NOTES:
1. Linear dimensions are in inches [millimeters]. Dimensions in parenthesis are for reference only. Controlling dimensions are in inches.
Dimensioning and tolerancing per ASME Y14.5M.
2. This drawing is subject to change without notice.
3. This dimension does not include mold flash, protrusions, or gate burrs. Mold flash, protrusions, or gate burrs shall not
exceed .006 [0.15] per side.
4. This dimension does not include interlead flash.
5. Reference JEDEC registration MS-012, variation AA.
www.ti.com
EXAMPLE BOARD LAYOUT
D0008A SOIC - 1.75 mm max height
SMALL OUTLINE INTEGRATED CIRCUIT
8X (.061 )
[1.55]
SYMM SEE
DETAILS
1
8
8X (.024)
[0.6] SYMM
(R.002 ) TYP
[0.05]
5
4
6X (.050 )
[1.27]
(.213)
[5.4]
EXPOSED
METAL EXPOSED
METAL
.0028 MAX .0028 MIN
[0.07] [0.07]
ALL AROUND ALL AROUND
4214825/C 02/2019
NOTES: (continued)
www.ti.com
EXAMPLE STENCIL DESIGN
D0008A SOIC - 1.75 mm max height
SMALL OUTLINE INTEGRATED CIRCUIT
8X (.061 )
[1.55] SYMM
1
8
8X (.024)
[0.6] SYMM
(R.002 ) TYP
5 [0.05]
4
6X (.050 )
[1.27]
(.213)
[5.4]
4214825/C 02/2019
NOTES: (continued)
8. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate
design recommendations.
9. Board assembly site may have different recommendations for stencil design.
www.ti.com
IMPORTANT NOTICE AND DISCLAIMER
TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATA SHEETS), DESIGN RESOURCES (INCLUDING REFERENCE
DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS”
AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY
IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD
PARTY INTELLECTUAL PROPERTY RIGHTS.
These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate
TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable
standards, and any other safety, security, regulatory or other requirements.
These resources are subject to change without notice. TI grants you permission to use these resources only for development of an
application that uses the TI products described in the resource. Other reproduction and display of these resources is prohibited. No license
is granted to any other TI intellectual property right or to any third party intellectual property right. TI disclaims responsibility for, and you
will fully indemnify TI and its representatives against, any claims, damages, costs, losses, and liabilities arising out of your use of these
resources.
TI’s products are provided subject to TI’s Terms of Sale or other applicable terms available either on ti.com or provided in conjunction with
such TI products. TI’s provision of these resources does not expand or otherwise alter TI’s applicable warranties or warranty disclaimers for
TI products.
TI objects to and rejects any additional or different terms you may have proposed. IMPORTANT NOTICE
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2024, Texas Instruments Incorporated