NJM2626

PWM 3-PHASE DC BRUSHLESS MOTOR CONTROL IC

! GENERAL DESCRIPTION ! Package Outline

The NJM2626 is a 3-phase DC brush less motor control pre-driver
IC with PWM control.
It takes hall IC inputs and generates motor driving waveform.
Output pre-driver is optimized to work with external power MOS
transistors for better power handling.
NJM2626V NJM2626VC3
The NJM2626 can easily implement 3-phase DC motor
application with speed control feature.

• Operating Voltage Vcc= 6V to 26V

• Pre-driver circuit
-Lower arm: Iout=+30mA/-30mA TYP.
-Upper arm: Iout=30mA TYP.
• Current limit sensing voltage Current limit=0.5V±10%
• Internal Oscillator
-Frequency control by external capacitor
• Forward or Reverse direction Internal pull-up resistor 10kΩ
• Internal Soft Start
-External capacitor to Verr pin
• Internal ON/OFF Circuit
-No-output is Verr pin to GND
• Bipolar Technology
• Package Outline SSOP-16/ SSOP20-C3

Ver.2009-02-26 -1-
NJM2626

! ABSOLUTE MAXIMUM RATINGS (Ta=25°C)

PARAMETER SYNBO
RATINGS UNIT
L
Logic Supply Voltage VCC 28 V
Maximum Output Current IoMAX 40 mA
Without Board 300
Power Dissipation (SSOP-16) PD mW
(*1) Mounted on the 2 layered PCB 640
(*1) Mounted on the 2 layered PCB 1000
Power Dissipation (SSOP20-C3) PD mW
(*1) Mounted on the 4 layered PCB 1500
Operating Temperature Range Topr -40 ∼ +85 °C
Storage Temperature range Tstg -50 ∼ +150 °C
(*1): Mounted on the glass epoxy board based on EIA/JEDEC. (114.3x76.2x1.6mm: 2Layer/4Layer)

-2- Ver.2009-02-26
 NJM2626

! ELECTRICAL CHARACTERISTICS (VCC=12V, Ct=1000pF, Cref=1µF, Ta=25°C)

PARAMETER SYMBOL TEST CONDITION MIN. TYP. MAX. UNIT
! General
Operation Supply Voltage VCC - 6.0 - 26.0 V
Output Enable
Under Voltage Sense Voltage UVLO 4.5 5.0 5.5 V
VCC Decreasing
Hysteresis Voltage
∆UVLO - 0.35 0.45 0.55 V
(Under Voltage Lock Out)
Supply Current ICC RL=∞ - 12.0 18.0 mA
! Reference Voltage Section
Reference Voltage Output Vref Iref=1.0mA 3.6 4.0 4.4 V
Line Regulation ∆VrefLI VCC=6V ∼ 18V - 50 100 mV
Load Regulation ∆VrefLO Iref=1.0mA ∼ 20.0mA - 10 50 mV
! Hall Amplifier Section
Input H Level Voltage VhH - VCC-0.8 - - V
Input L Level Voltage VhL - - - 0.8 V
Input Bias Voltage Iho Vin=0.8V - - -400 nA
Pull-up Resistance RPUH Vin=0.8V 7 10 13 kΩ
! Output Section
Under Arm Output Voltage 1 VOH(D) Isource=30mA 10 10.3 - V
Under Arm Output Voltage 2 VOL(D) Isink=30mA - 0.5 1.0 V
Output Clamp Voltage VCL(D) VCC=26V - 18 20 V
Upper Arm Output Voltage VOL(U) Isink=30mA - 0.5 1.0 V
Output Leak Current IoLEAK - - - 1.0 uA
! Over Current Sense Section
Sense Voltage VTH - 0.45 0.50 0.55 V
Hysteresis Voltage VTHhys - - 0.1 - V
Input Voltage Ratio VIN - - - 3.0 V
Input Bias Current IIB VIN=0V - -0.9 -5.0 µA
! Oscillator Section
Oscillation Frequency fosc - 22 27 33 kHz
Supply Voltage Change Ratio ∆fosc/∆V VCC=6V ∼ 18V - 1 5 %
PWM0% Sense Voltage PWM0 PWM DUTY=0% - - 0.35 V
PWM100% Sense Voltage PWM1 PWM DUTY=100% 3.5 - - V
Saw Wave Peak Voltage Vpfosc - 2.4 2.8 3.2 V
Saw Wave Bottom Voltage Vbfosc - 0.75 0.9 1.05 V

Ver.2009-02-26 -3-
NJM2626

! ELECTRICAL CHARACTERISTICS (VCC=12V, Ct=1000pF, Cref=1µF, Ta=25°C)

PARAMETER SYMBOL TEST CONDITION MIN. TYP. MAX. UNIT
! Error Amplifier Section
Input Offset Voltage VIO - - 7 - mV
Input Bias Current IIBRR - - -46 - nA
Input Common Mode
VICMRR - 0 - Vref V
Voltage Range
! Forward/ Reverse Direction Section (FR input terminal)
Output Forward Direction VF - Vref-0.8 - Vref V
Output Reverse Direction VR - - - 0.8 V
Hysteresis Voltage Ratio ∆VFR - - 0.5 - V
Pull-Up Resistance RPUFR - 7 10 13 kΩ
Note: Output switch test are performed under pulsed conditions to minimize power dissipation.

■ HALL INPUT vs HALL OUTPUT TRUTH TABLE

FR=L FR=H H:Source, L:Sink, X:Hi-Z
H1 H2 H3 H1 H2 H3 UH VH WH UL VL WL
H L H L H L X L X H L L
H L L L H H X X L H L L
H H L L L H X X L L H L
L H L H L H L X X L H L
L H H H L L L X X L L H
L L H H H L X L X L L H

■ FR INPUT TERMINAL
Terminal Voltage Direction
L input F
H input R

-4- Ver.2009-02-26
 NJM2626

! PIN CONFIGURATION

FR 1 16 VCC NC 1 20 NC

FR 2 19 VCC
Vref 2 15 UH

Vref 3 18 UH
H1 3 14 VH
H1 4 17 VH

H2 4 13 WH
H2 5 16 WH

H3 5 12 UL H3 6 15 UL

OSC 7 14 VL
OSC 6 11 VL

Verr 8 13 WL
Verr 7 10 WL
GND 9 12 llimit

GND 8 9 llimit
NC 10 11 NC

SSOP-16 SSOP20-C3

Ver.2009-02-26 -5-
NJM2626

! BLOCK DIAGRAM

FR
VCC
Vref
UH

H1
VCC

Rotor
H2 Position VH

VCC Decode

H3
WH

VCC
VCC

Vref Vref UVLO

UL
OSC Saw
Osillator

Logic
VL
+
Verr -
+
-
WL
+
GND -

ILimit

-6- Ver.2009-02-26
 NJM2626

! TYPICAL CHARACTERISTICS

ICC vs. VCC ICC vs. Temperature

25 20
Ta=25degC VCC=12V
H1=H2=H3=0V H1=H2=H3=0V
output=Open output=Open
OSC=1000pF OSC=1000pF
20 Verr=0V Verr=0V
15

15
ICC [mA]

Icc [mA]
10

10

5
5

0 0
0 5 10 15 20 25 30 35 40 -50 0 50 100 150

VCC [V] Temperature [degC]

UVLO vs. Temperature dUVLO vs. Temperature

1.2
6 output=Open
output=Open OSC=1000pF
OSC=1000pF Verr=3.5V
Verr=3.5V
1

5.5 UVLO-off

0.8
dUVLO [V]
UVLO [V]

5 0.6
UVLO-on

0.4

4.5

0.2

4 0
-50 0 50 100 150 -50 0 50 100 150

Temperature [degC] Temperature [degC]

Vref vs. VCC Vref vs. Io

5 5
Ta=25degC Ta=25degC
H1=H2=H3=0V VCC=12V
output=Open output=Open
4.5 OSC=1000pF 4.5 OSC=1000pF
Verr=0V Verr=3.5V
Vref=1mA

4 4
Vref [V]
Vref [V]

3.5 3.5

3 3

2.5 2.5

2 2
0 2 4 6 8 10 12 14 16 18 20 22 24 26 28 0 20 40 60 80 100

VCC [V] Io [mA]

Ver.2009-02-26 -7-
 NJM2626
■ TYPICAL CHARACTERISTICS

dVFR vs. Temperature

Vref vs. Temperature

1
VCC=12V
VCC=12V output=Open
H1=H2=H3=0V
4.4 OSC=1000pF
output=Open
Verr=3.5V
OSC=1000pF
Verr=0V 0.8

4.2

0.6

dVFR [V]
Vref [V]

0.4

3.8

0.2
3.6

-50 0 50 100 150 0

-50 0 50 100 150
Temperature [degC]
Temperature [degC]

VhH-L vs. Temperature VOH(D) vs. Io

2.5 12
VCC=12V Ta=25degC UL
output=Open VCC=12V VL
OSC=1000pF 11.5 output=Open WL
Verr=3.5V OSC=1000pF
Verr=3.5V
11

2
10.5
VOH(D) [V]
VhH-L [V]

10
VhH

9.5
1.5

9
VhL

8.5

1 8
-50 0 50 100 150 0 10 20 30 40 50

Temperature [degC] Io [mA]

VOH-d vs. Temperature VOL(D) vs. Io

12 3
VCC=12V Ta=25degC UL
output=Open VCC=12V VL
11.5 OSC=1000pF output=Open WL
Verr=3.5V 2.5 OSC=1000pF
Verr=3.5V
11

2
10.5
VOL(D) [V]
VOH-d [V]

10 1.5

9.5
1

0.5
8.5

8 0
-50 0 50 100 150 0 50 100 150 200

Temperature [degC] Io [mA]

Ver.2009-02-26 -8-
 NJM2626

! TYPICAL CHARACTERISTICS

VCL vs. Temperature

VTH vs. Temperature

18
VCC=28V 0.6
output=Open VCC=12V
OSC=1000pF output=Open
Verr=3.5V OSC=1000pF
17.5 Verr=3.5V
0.55

17 0.5 VTH
VCL [V]

VTH [V]
16.5 0.45

VTH-off

16 0.4

15.5 0.35

0.3
15
-50 0 50 100 150
-50 0 50 100 150
Temperature [degC]
Temperature [degC]

fosc vs. Temperature

fosc vs. VCC

30
35 VCC=12V
Ta=25degC H1=H2=H3=0V
H1=H2=H3=0V output=Open
output=Open OSC=1000pF
OSC=1000pF 28 Verr=0V
Verr=0V

30
26
fosc [kHz]
fosc [kHz]

24

25

22

20 20
0 5 10 15 20 25 30 35 40 -50 0 50 100 150

VCC [V] Temperature [degC]

RPU-FR vs. Temperature

20
VCC=12V
output=Open
OSC=1000pF
Verr=3.5V

15
RPU-FR [k-ohm]

10
[CAUTION]
The specifications on this databook are only
given for information , without any guarantee
as regards either mistakes or omissions. The
application circuits in this databook are
described only to show representative usages
5 of the product and not intended for the
-50 0 50 100 150 guarantee or permission of any right including
the industrial rights.
Temperature [degC]

Ver.2009-02-26 -9-