Gear Pump IPH

C Gear Pumps(P01-13)_E.
03.11.20 1:20 PM
Page 1
IPH SERIES IP PUMP
IPH Series
IP Pump
3.6 to 125.9cm3/rev
30MPa
This is a new design series in which all pump types are installation compatible with previous designs. Note, however, that there is no
longer compatibility for some of the seal components between the IPH-3 and IPH-4 sizes and design numbers 10 and 12.
Features
wOutstanding durability and very long life.
eA modified involute short-tooth gear
enables internal gearing for greatly
reduced pulsation and noise, and excep-
tionally quiet operation.

rA simple structure makes maintenance and
inspection easier.
Specifications
Model No.
IPH-2A(B)-
Rated Voltage
MPa
Maximum Operating
Pressure
MPa{kgf/cm2}
Minimum Revolution
Speed
min 1
Maximum Revolution
Speed
min 1
Weight kg
Type A
Type B
3.5-11
3.60
4.4
2.4
5.24
4.5
2.5
6.5
6.55
4.6
2.6
8.18
4.8
2.8
10.5
4.8
10.7
5.0
5.3
IPH-3A(B)- 10-20
25 {255}
30 {306}
600
2000
10.2
13
13.3
16
15.8
11.0
20.7
15.2
9.5
15.7
10.0
IPH-4A(B)- 20-20
25 {255}
25 {255}
30 {306}
32
32.3
16.2
10.5
40.8
32.0
19.0
33.0
20.0
50.3
64
63.9
34.0
21.0
81.3
62.0
39.0
64.0
41.0
66.0
43.0
100
101.6
125
125.9
1.Capacity: Logical discharge rate per

rotation.
2.Suction Pressure: +0.03 to +0.3MPa
{0.3 to +0.3kgf/cm2}
3.Maximum working pressure shown
here is the pressure limit when there
are frequent pressure changes.
4.Avoid installation with the suction port
towards the bottom of the pump.
5.Specify using the model number format
shown below when pipe flanging is
required.
25 {255}
Size 2, 3, 4, 5, 6
IPH Series IP Pump
300
Handling
zFor the hydraulic operating fluid, use
an R&O type and wear-resistant type
of ISO VG32 to 68 or equivalent (viscosity index of at least 90). Use
hydraulic operating fluid that provides
kinematic viscosity during operation in
the range of 20 to 150mm2/s.
xThe operating temperature range is 5
to 65C. When the oil temperature at
Understanding Model Numbers

IPH 4 B 25 LT 20
30 {306}
400
2000
50
IPH-6A(B)- 80-21(11)
30 {306}
500
2000
25.7
25 {255}
30 {306}
600
25
IPH-5A(B)- 40-21(11)
Note)
Capacity
cm3/rev
2000
2000
startup is 5C or less, perform a

warm-up operation at low pressure
until the oil temperature reaches 5C.
Use the pump in an area where the
temperature is within the range of 0 to
60C.
cSuction pressure is -0.03 to
+0.03MPa (-0.3 to +0.3kgf/cm2), and
the suction port flow rate should be to
greater than 2m/sec.
vAvoid pulley, gear, and other drive
systems that impart a radial or thrust
load on the end of the pump shaft.
bMount the hydraulic pump so its pump
shaft is oriented horizontally. Provide
a suction strainer with a filtering grade
of about 100m (150 mesh). For the
return line to the tank, use a 25m
line filter.
nManage hydraulic operating fluid so
contamination is maintained at class
NAS10 or lower. Take care to avoid
contamination with water and other
foreign matter, and watch out for discoloration. Whitish fluid indicates that
air has contaminated the fluid, and
brownish fluid indicates the fluid is dirty.
(Continued on following page)
C-1
Gear Pumps
qA patented axial and radial pressure loading system provides high efficiency and
generates pressures up to 30MPa
{306kgf/cm2}.
C Gear Pumps(P01-13)_E.q
03.11.20 1:20 PM
mWhen using water- or glycol-based

hydraulic operating fluid, refer to page
O-3 for details on applicable models
of hydraulic pumps.
,At startup, repeat the inching operation (start-stop) to bleed air from the
pump and pipes.
.Equip an air bleed valve in circuits
Page 2
where it is difficult to bleed air before

startup. See page C-13 for more
information.
0To ensure proper lubrication of the
pump's rubbing surfaces, supply oil to
the interior of the pump before starting
operation.
1W hen centering the pump shaft,
eccentricity with the motor shaft

should be no greater than 0.05mm.
Use a pump mounting base of sufficient rigidity. The angle error should
be no greater than 1.
2Contact your agent for information
about engines.
Discharge Rate and Required Input for Each Pump Speed
Speed
0.7
Model No.
Gear Pumps
IPH-2A(B)-
1000
min-1
14
21
25
30
3.49
5.09
6.37
7.95
3.39
4.93
6.19
7.74
3.28
4.78
6.03
7.54
3.23
4.70
5.93
7.40
3.15
4.60
5.82
7.26
0.7
14
21
25
30
0.09
0.12
0.16
0.19
0.62
0.79
0.97
1.19
1.12
1.47
1.82
2.24
1.63
2.26
2.79
3.45
1.93
2.63
3.25
4.01
2.30
3.19
3.95
4.86
6.14
7.73
9.19
9.95
13.0
15.4
9.71
12.7
15.1
9.47
12.4
14.8
9.23
12.3
14.6
9.17
12.1
14.3
0.25
0.32
0.37
1.59
2.02
2.37
2.73
3.57
4.23
4.25
5.35
6.35
5.06
6.29
7.47
IPH-4A(B)- 20-20
25
32
20.7
25.7
32.3
20.2
25.2
31.6
19.8
24.7
31.0
19.3
24.2
30.4
19.1
23.9
30.1
18.8
23.6
29.6
0.50
0.61
0.75
3.13
3.79
4.71
5.56
6.89
8.67
8.24
10.3
12.8
9.80
12.1
15.3
11.7
14.6
18.4
IPH-5A(B)- 40-21(11)
50
64
40.8
50.3
63.9
39.9
49.3
62.6
39.0
48.4
61.4
38.1
47.3
60.2
37.6
46.8
59.5
37.0
46.2
58.6
0.99
1.20
1.49
6.18
7.42
9.32
10.9
13.6
17.2
16.3
20.1
25.5
19.3
23.8
30.6
23.8
28.6
36.3
IPH-6A(B)- 80-21(11)
100
125
81.3
101.6
125.9
79.5
99.6
123.4
77.7
97.7
121.1
76.0
95.8
118.7
75.1
94.6
117.2
73.8
93.2
115.6
1.98
2.42
2.94
21.8
27.3
33.9
32.3
40.5
50.1
38.4
48.1
59.6
46.7
57.7
71.5
3.5-11
5
6.5
8
4.32
6.28
7.86
9.81
4.20
6.12
7.67
9.58
4.08
5.95
7.48
9.34
3.97
5.79
7.29
9.11
3.91
5.70
7.18
8.97
3.83
5.58
7.05
8.81
11.8
14.6
17.8
0.11
0.15
0.19
0.23
0.66
0.95
1.16
1.44
1.23
1.77
2.19
2.70
1.83
2.62
3.24
4.00
2.15
3.09
3.81
4.70
2.61
3.74
4.63
5.71
5.93
7.56
8.98
7.20
9.28
11.1
IPH-3A(B)- 10-20
13
16
12.2
15.9
18.9
11.9
15.9
18.5
11.7
15.3
18.2
11.4
15.0
17.8
11.3
14.8
17.6
11.1
14.6
17.4
0.30
0.39
0.45
1.86
2.37
2.77
3.28
4.28
5.09
4.93
6.42
7.63
IPH-4A(B)- 20-20
25
32
24.8
30.8
38.7
24.3
30.3
38.1
23.8
29.8
37.4
23.4
29.3
36.8
23.1
29.0
36.3
22.8
28.6
35.9
0.62
0.75
0.92
3.76
4.56
5.66
6.67
8.27
10.4
9.88
12.3
15.5
11.8
14.7
18.4
14.2
17.5
22.0
IPH-5A(B)- 40-21(11)
50
64
48.9
60.3
76.6
48.0
59.3
75.3
47.1
58.3
74.0
46.1
57.3
72.8
45.5
56.6
72.0
44.9
56.0
71.2
1.22
1.47
1.83
7.42
8.91
11.2
13.2
16.2
20.6
19.5
24.0
30.5
23.1
28.6
36.3
28.4
34.3
43.5
IPH-6A(B)- 80-21(11)
100
125
97.5
121.9
151.0
95.7
119.7
148.4
93.8
117.7
145.9
91.9
115.8
143.4
90.9
114.5
141.9
89.5
113.1
140.3
2.42
2.96
3.60
14.3
17.5
21.5
26.2
32.3
40.1
38.7
48.4
60.1
46.2
57.7
71.6
56.1
69.2
85.9
5.40
7.86
9.82
12.3
5.25
7.65
9.59
11.9
5.10
7.44
9.35
11.6
4.97
7.24
9.12
11.4
4.89
7.11
8.97
11.2
4.79
6.97
8.82
11.0
0.14
0.20
0.25
0.30
0.96
1.17
1.49
1.78
1.68
2.21
2.73
3.37
2.46
3.31
4.09
5.05
2.89
3.85
4.76
5.87
3.46
4.69
5.78
7.14
IPH-3A(B)- 10-20
13
16
15.3
19.9
23.7
14.9
19.5
23.2
14.6
19.1
22.7
14.3
18.8
22.3
14.1
18.6
22.1
13.9
18.3
21.8
0.40
0.51
0.59
2.31
2.95
3.46
4.15
5.41
6.42
6.22
8.03
9.53
7.40
9.44
11.2
8.99
11.6
13.8
IPH-4A(B)- 20-20
25
32
31.0
38.5
48.4
30.4
37.8
47.6
29.8
37.2
46.8
29.3
36.6
45.9
28.9
36.1
45.4
28.4
35.7
44.9
0.81
0.98
1.20
4.70
5.69
7.07
8.33
10.4
13.1
12.4
15.4
19.3
14.7
18.3
22.9
17.6
21.9
27.5
IPH-5A(B)- 40-21(11)
50
64
61.2
75.4
95.8
60.0
74.1
94.2
58.8
72.8
92.5
57.6
71.6
91.0
56.9
70.8
90.0
56.2
70.0
89.0
1.59
1.91
2.38
9.51
11.4
14.4
16.6
20.5
26.0
24.7
30.4
38.6
29.3
36.1
45.9
36.0
43.3
55.1
IPH-6A(B)- 80-21(11)
100
125
121.9
152.4
188.8
119.5
149.7
185.5
117.3
147.3
182.5
115.0
144.7
179.3
113.5
143.2
177.5
111.9
141.5
175.3
3.16
3.86
4.69
18.3
22.5
27.5
33.1
41.4
51.3
49.0
61.4
76.0
58.4
73.0
90.4
70.9
87.6
108.1
IPH-2A(B)-
1800
min-1
3.60
5.24
6.55
8.18
10.2
13.3
15.8
IPH-2A(B)-
1500
min-1
3.5-11
5
6.5
8
Required Input kW
IPH-3A(B)- 10-20
13
16
IPH-2A(B)-
1200
min-1
Discharge Rate r/min
Pressure MPa
3.5-11
5
6.5
8
3.5-11
5
6.5
8
6.48
9.43
11.7
14.7
6.33
9.21
11.5
14.4
6.16
8.99
11.2
14.1
6.01
8.76
11.0
13.7
5.92
8.61
10.9
13.6
5.82
8.46
10.7
13.3
0.17
0.24
0.30
0.37
1.16
1.45
1.78
2.20
2.02
2.65
3.27
4.04
2.95
3.47
4.92
6.06
3.46
4.62
5.71
7.05
IPH-3A(B)- 10-20
13
16
18.3
23.9
28.4
18.0
23.5
27.9
17.6
23.1
27.5
17.3
22.7
27.0
17.1
22.5
26.7
16.8
22.2
26.4
0.49
0.62
0.72
2.90
3.67
4.30
5.04
6.57
7.80
7.47
9.63
11.4
8.89
11.3
13.5
10.8
13.9
16.5
IPH-4A(B)- 20-20
25
32
37.2
46.2
58.1
36.6
45.6
57.3
36.0
44.9
56.5
35.4
44.3
55.5
35.0
43.8
55.1
34.5
43.3
54.5
0.99
1.20
1.48
5.64
6.83
8.47
10.0
12.4
15.6
14.9
18.5
23.1
17.6
21.9
27.5
21.2
26.3
33.0
IPH-5A(B)- 40-21(11)
50
64
73.4
90.5
115.0
72.1
89.2
113.4
70.9
87.9
111.6
69.7
86.6
110.0
69.0
85.9
109.1
68.1
85.0
108.0
1.95
2.34
2.92
11.7
14.1
17.6
20.2
24.9
31.6
30.0
36.9
46.8
35.6
43.8
55.7
43.7
52.6
66.9
IPH-6A(B)- 80-21(11)
100
125
146.3
182.8
226.6
143.7
180.2
223.3
141.4
177.6
220.1
139.0
174.9
216.9
137.5
173.5
215.0
135.8
171.7
212.7
3.88
4.74
5.75
22.4
27.7
33.8
40.2
50.3
62.2
59.6
74.4
92.3
70.9
88.6
110.0
86.1
106.0
131.5
Note) Values in the table are general values at an operating fluid viscosity of 46mm2/s. Use the values when selecting the model for your needs.
C-2
4.15
5.61
6.93
8.56
03.11.20 1:20 PM
Page 3
Installation Dimension Drawings

IPH-2A-*-11 (Foot Mounting, Clockwise Rotation)
96
50.8 32.5
4 to 22x1counterbore
11holes
152.5
Suction port flange

SAEJ518b-1/2
C
Gear Pumps
51
127
38.1
4 to M8x12
13
17.5
59
17.5
34
17.5
3.968 -0.018
Discharge port flange

SAEJ518b-1/2
13
5.47
69.8 0.1
115.3
38.1
135
4 to M8x12
LB
0
17.73 0.25
LA
0
15.875 0.025
IPH-2B-*-11 (Flange Mounting, Clockwise Rotation)
38.1
4 to M8x12
51
Suction port flange

SAEJ518b-1/2
13
17.5
17.5

SAEJ518b-1/2
11
45.5
0
82.55 0.035
38.1
12
52
4
53
34
5.47
4 to M8x12
130
106.4
0
3.968 0.018
59
LB
0
17.73 0.25
LA
0
15.875 0.025
Dimensions (mm)
Model No.
LA
LB
IPH-2*-3.5-*-11
107
51.0
8.9
IPH-2*-5 -*-11
112
53.5
11
IPH-2*-6.5-*-11
116
55.5
12
IPH-2*-8 -*-11
121
58.0
13
Note) IPH-2A (B)-*-L-11 (foot mounting/flange mounting, counterclockwise rotation) are the
mirror image of the drawings shown above. In the case the suction port flange is facing upwards, the discharge port flange is positioned to the right when viewed from the
shaft side.
C-3
03.11.20 1:20 PM
Page 4

140
114.3
12.7
Gear Pumps
Suction port flange

SAEJ518b-1
246
220.7
64
52.4
4 to M10x15
26.2
0
4.76 0.018
165.2
38.1
6.8
195.5
38
17.5

SAEJ518b-1/2
16
4 to M8x15
65
16
107.95 0.1
LB
0
21.15 0.25
LA
0
0.025
64
52.4
4 to M10x15
Suction port flange

SAEJ518b-1
25
0
4.76 0.018
13

SAEJ518b-1/2
17.5
65.3
57.2
6.8
38.1
168
146
13
LB
4 to M8x15
65
5
58
38
0
101.6 0.051
LA
0
21.15 0.25
26.2
0
19.05 0.025
Dimensions (mm)
Model No.
C-4
LA
LB
IPH-3*-10-*-20
128.5
60.0
14
IPH-3*-13-*-20
134.5
63.0
17
IPH-3*-16-*-20
139.5
65.5
18
shaft side.
03.11.20 1:20 PM
Page 5

140
114.3
4 to 22x1counterbore
11holes
12.7
77
Suction port flange

SAEJ518b-11/ 4
246
220.7
58.7
4 to M10x14
C
Gear Pumps
32
30.2

SAEJ518b-3/4
22
16
195.5
47.5
174.3
8.7
60
0
6.375 0.025
107.950.1
78
16
LB
0
27.85 0.25
LA
4 to M10x15
0
25.385 0.025
77
58.7
4 to M10x14
Suction port flange

SAEJ518b-11/ 4
32
30.2

SAEJ518b-3/4
22
13.5
66.3
144
8.7
47.5
13
172
146
0
6.375 0.025
0
101.6 0.051
LB
4 to M10x15
78
6
69.5
60
0
27.85 0.25
LA
0
25.385 0.025
Dimensions (mm)
Model No.
LA
LB
IPH-4*-20-*-20
164.5
71
18
IPH-4*-25-*-20
170.5
74
20
IPH-4*-32-*-20
178.5
78
24
shaft side.
C-5
03.11.20 1:20 PM
Page 6

203
139.7
4 to 35x counter bore

18 holes
44.5
Gear Pumps
36
295.3
334
95
70
4 to M12x19
Suction port flange

SAEJ518b-11/ 2
42
LB
0
7.938 0.051

SAEJ518b-1
25
52.4
152.4 0.1
239.2
259
11.2
85
25
60
0
35.3310.25
LA
4 to M10x15
26.2
0
31.75 0.051
95
70
4 to M12x19
42
18

SAEJ518b-1
26.2
17.5
11.2
52.4
4 to M10x15
85
6
76
65
86.8
LB
194.8
LA
210
181
0
7.938 0.051
0
1270.051
36
0
35.3310.25
Suction port flange

SAEJ518b-11/ 2
31.75
0
0.051
Dimensions (mm)
Model No.
C-6
LA
LB
IPH-5*-40-*-21 (11)
201.5
91.0
24
IPH-5*-50-*-21 (11)
208.5
94.5
26
IPH-5*-64-*-21 (11)
218.5
99.5
28
Note) IPH-5A (B)-*-L-21 (11) (foot mounting/flange mounting, counterclockwise rotation) are
the mirror image of the drawings shown above. In the case the suction port flange is
facing upwards, the discharge port flange is positioned to the right when viewed from
the shaft side.
03.11.20 1:20 PM
Page 7
220.7
149.2
37x1counter bore
20holes
4 to
49.5
120
42.9
374
330.2
77.8
4 to M12x23
100
30
11.113 0.051
36

SAEJ518b-11/ 2
30
336.7
310.2
70
13.7
70
203.2 0.1
LB
49.4280.25
LA
4 to M12x20
Gear Pumps
Suction port flange

SAEJ518b-2
50
44.45 0.051
0
120
77.8
4 to M12x23
Suction port flange

SAEJ518b-2
42.9
50
0
0.063
107
36

SAEJ518b -1 1/ 2
244
70
20
22
11.113 0.051
13.7
6
92
70
228.6
152.4
LB
4 to M12x20
100
49.428 0.25
264
LA
0
44.45 0.051
Dimensions (mm)
Model No.
LA
LB
IPH-6*- 80-*-21 (11)
241.5
111.5
32
IPH-6*-100-*-21 (11)
251.5
116.5
36
IPH-6*-125-*-21 (11)
263.5
122.5
38
Note) IPH-6A (B)-*-L-21 (11) (foot mounting/flange mounting, counterclockwise rotation) are
the mirror image of the drawings shown above. In the case the suction port flange is
facing upwards, the discharge port flange is positioned to the right when viewed from
the shaft side.
C-7
03.11.20 1:20 PM
Page 8
Performance Curves
Overall efficiency
Gear Pumps
Noise level
Volume efficiency
Revolution Speed
1200min 1
Operating Hydraulic Fluid Viscosity
46mm2/s
Representative Characteristics Under Above Conditions
Cross-sectional Drawing
IPH-*B-*-**
Part No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
C-8
Part Name
Body -1
Body -2
Mounting
Rear cover
Pinion shaft
Radial piston
Internal gear
Bushing
Knock pin
Stopper pin
Spring pin (guide pin)
Axial plate -1
Axial plate -2
Feeler piece
Spring holder
Spring
Key
Radial seal
Radial backup ring
Axial backup ring
Backup ring
Bearing
Oil seal
Pin
O-ring
O-ring
O-ring
O-ring
Snap ring
Screw
Washer
Wave washer
03.11.20 1:20 PM
Page 9
IPH Series Seal Kit

Understanding Seal Kit IHAS 2 S
Model Numbers :
10(20, 30)
Design number (IPH3 : 20D, IPH4 : 30D)
Capacity classification D35 to 125
Size 2, 3, 4, 5, 6
S: Shaft side single pump or double pump
H: Head side double pump
Indoor/outdoor use sealing
IPH Series Seal Kit
Seal Kit Number
18
19
Q'ty
Radial Seal
IHAS-2S2D35-10
20
Q'ty
Radial Backup Ring
IPH-2A(B)-3.5-11
IH34J-102D35-1A
2S2005-10
102005-1A
2S2D65-10
6.5
102D65-1A
2S2008-10
IHAS-2S3010-20
8
IPH-3A(B)-10-20
2S3013-20
13
2S3016-20
IHAS-2S4020-30
16
IPH-4A(B)-20-20
2S4025-30
25
2S4032-30
IHAS-2S5040-10
32
IPH-5A(B)-40-21(11)
102008-1A
IH34J-103010-1A
103013-1A
IH34J-402D35
402005
402D65
402008
IH34J-403010
403013
IH34J-203000
103016-1A
403016
IH34J-204000-1A
IH34J-404020
104025-2A
404025
404032
IH34J-405040
405050
405064
IH34J-406080
406100
406125
104032-2A
IH33J-105040-1A
IH34J-105040-1A
50
105050-1A
105050-1A
2S5064-10
64
105064-1A
105064-1A
IH33J-106080-1A
IH34J-106080-1A
IPH-6A(B)-80-21(11)
IH34J-202000
Q'ty
Backup ring
IH34J-104020-2A
2S5050-10
IHAS-2S6080-10
21
Q'ty
Axial Backup Ring
2S6100-10
100
106100-1A
106100-1A
2S6125-10
125
106125-1A
106125-1A
IH34J-205000
IH34J-206000
Component Part Numbers

Seal Kit Number
23
25
Q'ty
Oil seal
IHAS-2S2D35-10
2S2005-10
2S2D65-10
2S2008-10
IHAS-2S3010-20
2S3013-20
2S3016-20
IHAS-2S4020-30
2S4025-30
2S4032-30
IHAS-2S5040-10
2S5050-10
2S5064-10
IHAS-2S6080-10
2S6100-10
2S6125-10
Note)
26
Q'ty
O-ring
ISD-20328
27
Q'ty
O-ring
R68 2
28
Q'ty
O-ring
Q'ty
O-ring
R23 2
R10 2
R10 2
R12 2
R12 2
2
2
R14 2
R14 2
R16 2
R16 2
ISD-25388
R86 2
R30 2
R15 2.5
R15 2.5
R18 2.5
R18 2.5
R20 2.5
R20 2.5
ISD-32458
R108 3
R38 2.5
R21 2.5
R21 2.5
R23 3
R23 3
R26 3
R26 3
ISD-40558
R140 3
R49 3
R26 3
R29 3.5
R33 3.5
ISD-50659
R172 4
R60 3.5
R34 3.5
R38 4
R43 4
1.Oil seals are manufactured by Nippon Oil Seal Industry Co. Ltd. (NOK).
2.O-rings are not available through retail sources. Consult your agent for more information.
C-9
Gear Pumps
Component Part Numbers

Applicable
Pump Model No.
03.11.20 1:20 PM
Page 10
IHF 3 T 20
IPH Series Pipe Flange Kit

Understanding Flange Kit Model Numbers :
Design number
: 20 Design
The pipe flange kit combines the flanges, bolts, washers, and O-rings
required for each type of pump into a single kit.
The component parts table shows the screw in type flange kit. In the case of
the welded type flange, the flange part number is IH03J-200040 (1 of IH03J100040 changes to 2). All other included parts are the same.
T : Screw in type
E : Welded type
Pump size
: Single pump
2 to 6
: Double pump
22 to 46
C
Gear Pumps
Screw in type
Flange Kit model No.
IN Flange
Applicable Pump
Model No.
Flange Part No.
Bolt
Washer
O-ring
IHF-2-T-20
IPH-2A(B)-*-11
IH03J-100040
TH- 8 45
WS-B- 8
IB-P22
IHF-3-T-20
IPH-3A(B)-*-20
IH03J-100080
TH-10 50
WS-B-10
IB-G35
IHF-4-T-20
IPH-4A(B)-*-20
IH03J-100100
TH-10 55
IB-G40
TH-12 55
WS-B-12
IB-G50
TH-12 60
IB-G60
IHF-5-T-20
IPH-5A(B)-*-21(11)
IHF-6-T-20
IH03J-100120
IPH-6A(B)-*-21(11)
IH03J-100160
OUT Flange
Plug
Flange Part No.
Bolt
Washer
O-ring
IH03J-100040
TH- 8 45
WS-B- 8
IB-P22
TPHA-1/4
IH03J-100040
TH- 8 45
IB-P22
IH03J-100060
TH-10 50
WS-B-10
IB-G30
IH03J-100080
TH-10 50
IB-G35
IH03J-100120
TH-12 60
WS-B-12
IB-G50
Screw in type
Flange Kit model No.
IHF-22-T-20
Note)1.In the case of a double pump, the

flange kit includes three flanges:
one for the common IN port and
two OUT port flanges. When using
separate IN ports, use separate
single pump flange kits, one each
for the head side and the shaft
side.
Note)2.There is no common IN port in the
case of the double pump models
IPH-55, IPH-56, and IPH-66, or a
single IN port is used.
IN Flange
Applicable Pump Model

No.
Flange Part No.
IPH- 22B-*-*-11
Bolt
Washer
O-ring
IH03J-100060
TH-10 50
WS-B-10
IB-G30
WS-B-12
IB-G35
IB-G50
IB-G60
IHF-23-T-20
23
IH03J-100080
IHF-24-T-20
24
IH03J-100120
TH-12 55
IHF-25-T-20
25
IH03J-100160
TH-12 60
IHF-26-T-20
26
IH03J-100200
TH-12 65
IB-G75
IH03J-100100
TH-10 55
WS-B-10
IB-G40
IHF-33-T-20
IPH- 33B-*-*-11
IHF-34-T-20
34
IH03J-100120
TH-12 55
WS-B-12
IB-G50
IHF-35-T-20
35
IH03J-100160
TH-12 60
IB-G60
IHF-36-T-20
36
IH03J-100200
TH-12 60
IB-G75
IH03J-100120
TH-12 55
IB-G50
WS-B-16
IB-G75
IB-G85
IHF-44-T-20
IPH- 44B-*-*-11
IHF-45-T-20
45
IH03J-100200
TH-12 65
IHF-46-T-20
46
IH03J-100240
TH-16 75
OUT Flange (Shaft Side)

Flange Part No.
Bolt
OUT Flange (Head Side)
Washer
TH- 8 45
TH-10 50
4
4
TH-12 60
IH03J-100040
IH03J-100060
O-ring
Flange Part No.
Bolt
Washer
Plug
O-ring
WS-B- 8
IB-P22
IH03J-100040
TH- 8 45
WS-B- 8
IB-P22
TPHA-1/4
WS-B-10
IB-P22
IB-G30
IB-G35
WS-B-12
IB-G50
IB-P22
IB-P22
WS-B- 8
WS-B- 8
TH- 8 45
TH- 8 45
IH03J-100040
TH-10 50
WS-B-10
IB-G30
IH03J-100080
IB-G35
WS-B-12
IH03J-100120
TH-12 60
IB-G50
WS-B-10
IB-G30
IB-G30
TH-10 50
WS-B-10
TH-10 50
IH03J-100060
IH03J-100060
IH03J-100080
IB-G35
WS-B-12
IH03J-100120
TH-12 60
IB-G50
IH03J-100040
IH03J-100040
IH03J-100060
IH03J-100080
IH03J-100120
C-10
03.11.20 1:20 PM
Page 11
Pipe Flange Installation Dimension Diagram
C
Gear Pumps
Screw in type
Pipe Flange Kit
Part Number
SAE Standard
Nominal
Diameter
Dimensions (mm)
A
d1
d4
Weight
kg
IH03J -100040
SAE J518b 1/2
1/2
54
46
38.1
17.5
33
12.7
0.4
-100060
SAE J518b 3/4
3/4
65
52
47.5
22.0
33
11
20
0.6
-100080
SAE J518b 1
70
59
52.4
26.2
33
11
27
0.6
-100100
SAE J518b 11/4
11/4
79
73
58.7
30.2
38
11
33
1.0
-100120
SAE J518b 11/2
11/2
94
83
70.0
36.0
38
13
37.5
1.4
-100160
SAE J518b 2
-100200
SAE J518b 21/2
-100240
SAE J518b 3
102
97
77.8
42.9
38
13
50
1.7
21/2
114
109
88.9
50.8
43
13
60
2.1
135
131
106.4
61.9
48
17.5
71
3.3
Pipe
Diameter
d1
d2
d3
Welded Type
Dimensions (mm)
Pipe Flange Kit

Part Number
SAE Standard
IH03J -200040
SAE J518b 1/2
1/2
54
46
-200060
SAE J518b 3/4
3/4
65
52
-200080
SAE J518b 1
70
-200100
SAE J518b 11/4
11/4
79
11/2
11/2
2
21/2
3
-200120
SAE J518b
-200160
SAE J518b 2
-200200
SAE J518b 21/2
-200240
SAE J518b 3
d4
Weight
kg
38.1
17.5
33
11
22.2
27
12.7
0.4
47.5
22.0
33
12
11
27.7
35
20
0.6
59
52.4
26.2
33
14
11
34.5
42
27
0.6
73
58.7
30.2
38
16
11
43.2
48
33
1.0
94
83
70.0
36.0
38
18
13
49.1
58
37.5
1.4
102
97
77.8
42.9
38
19
13
61.1
68
50
1.7
114
109
88.9
50.8
43
22
13
77.1
82
60
2.1
135
131
106.4
61.9
48
25
17.5
90.0
97
71
3.3
Recommended Tightening Torque for Flange Installation Bolts

Mounting bolt
Tightening Torque N . m {kgf . cm}
M8
25.5 to 32.3 {260 to 329}
M14
142.1 to 176.4 {1450 to 1800}
M10
50.9 to 64.7 {520 to 660}
M16
215.6 to 274.4 {2200 to 2800}
M12
88.2 to 112.7 {900 to 1150}
M18
294
to 382.2 {3000 to 3900}
Note) There is no RC (previously PT) 1/4 tap for the above flange numbers (exclusively for suction port use)
marked with a star ().
C-11
03.11.20 1:20 PM
Page 12
IPH Series Foot Mounting Kit

Understanding Foot Mounting Kit
Numbers:
When only the mounting feet are required
for a single pump or double pump, pump
mounting bolts, washers and other parts
are sold together as the Foot Mounting
Kit.
IHM 2 10
Design number
Pump size : Single pump 2 to 6
: Double pump 22 to 66
IPH Series
Foot Mounting Kit
Gear Pumps
Foot Mounting Installation Measurement Chart

SAE-2BOLT-MOUNTING
SAE-4BOLT-MOUNTING
SAE-2BOLT-MOUNTING
Foot Mounting
Kit Model No.
Applicable Pump Model No.
Accessories
Dimensions (mm)
SINGLE
PUMP
DOUBLE PUMP
Bolt
Q'ty
Washer
Q'ty
IHM-2-10
IPH-2
TB-10 30
WP-10
127
152.5
IHM-4-10
IPH-3
TB-12 30
WP-12
220.7
246
IHM-4-10
IPH-4
69.8
50.8
96
107.95
114.3
140
114.3
140
TB-12 30
WP-12
220.7
246
107.95
IPH-22
TB-10 30
WP-10
171.45
204
107.95
IHM-44-10
IPH23, IPH-33
TB-12 30
WP-12
235
267
139.7
127
193
IHM-44-10
IPH-24, IPH-34, IPH-44
TB-12 30
WP-12
235
267
139.7
127
193
TB-16 40
WP-16
295.3
334
152.4
139.7
203
TB-20 50
WP-20
330.2
374
203.2
149.2
220.7
d1
d2
d3
d4
Weight
kg
82.55
IHM-22-10
IHM-45-10
IPH-5
95.25
150
IHM-46-10
IPH-6
Foot Mounting
Kit Model No.
(J)
(S)
IHM-2-10
74
41.5
17.5
13
M10
135
32.5
36.5
22
11
106.4
50
2.0
IHM-4-10
61.7
49
16
16
M12
195.5
12.7
53
101.6
22
11
146
40
5.5
IHM-4-10
74.7
62
16
16
M12
195.5
12.7
53
101.6
22
11
146
40
5.5
IHM-22-10
73.5
41
18
18
M10
180
32.5
50
22
11
106.4
40
6.5
IHM-44-10
89.5
45
20
20
M12
232
44.5
57.5
101.6
22
14
146
40
12.0
IHM-44-10
102.5
58
20
20
M12
232
44.5
57.5
101.6
22
14
146
40
12.0
IHM-45-10
104.5
60
25
25
M16
259
44.5
61
127
35
18
181
86
13.5
IHM-46-10
119.5
70
30
30
M20
337
49.5
64
152.4
37
20
228.6
100
22.0
Dimensions (mm)
82.55
*IHM-2-10, IHM-4-10, and IHM-45-10 are the same as PVS pump foot mounting PSM-101000, PSM102000, and PSM103000 respectively.
SAE-4BOLT-MOUNTING
Foot Mounting
Kit Model No.
C-12
Applicable Pump
Model No.
Accessories
DOUBLE PUMP
Dimensions (mm)
Bolt
Q'ty
Washer
Q'ty
(I)
WS-B-20
330
370
200
125
125
300
17
WS-B-24
380
430
260
140
140
340
17
IHM-55-10
IPH-55
TH-20 50
IHM-66-10
IPH56, IPH-66
TH-24 60
Dimensions (mm)
Foot Mounting
Kit Model No.
(J)
d1
d2
d4
Weight
kg
IHM-55-10
47
30
224.6
224.6
30
M20
340
275
IHM-66-10
52
40
247.5
247.5
40
M24
415
310
20
90
165.1
34
18
140
32.0
25
105
177.8
34
18
150
48.0
03.11.20 1:20 PM
Page 13
Air Bleed-off Valve

Equipping an air bleed-off valve on the
pump's discharge side helps to simplify
air bleeding during test operation.
Specifications
qAir inside the pump and the suction pipe is
exhausted rapidly when the pump is started up.
When discharge pressure reaches 0.2MPa
{2.0kgf/cm2} or greater after the pump intakes oil, a
valve closes to prevent oil from leaking.
wMaximum operating pressure: 30MPa
{306kgf/cm2}
eProvide piping to ensure that the tank port is under
the oil level surface.
C
Gear Pumps
Understanding Model Numbers

CAB T 02 1 10
Design
number
Valve open pressure
1: 0.24MPa
{2.4kgf/cm2}
A: 0.18MPa
{1.8kgf/cm2}
Part No.
Part Name
Q'ty
Piping (nominal diameter)
Valve body
Mounting method
T: Screw connection type
Snap ring
Valve
Spring
Air bleed-off valve
Note 1)If chattering occurs in a circuit when CAB-T02-1-10 is used, use CAB-T02-A-10 instead.
2)If chattering occurs in a circuit when CAB-T02-A-10 is used, use of a CAB air bleed-off valve is not required.
Application Examples
Example of Circuits that Require an Air Bleed-off Valve
qWhen using a Type 2 or Type 3 check valve (Sample Circuit A)
wWhen unload circuit function cannot be achieved (Sample Circuit A)
eWhen the discharge sides of multiple pumps run together (Sample Circuit B)
Circuit Diagram A
Circuit Diagram B
C-13

Gear Pump IPH

Uploaded by

Copyright:

Available Formats

Gear Pump IPH

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Gear Pump IPH

Uploaded by

Copyright:

Available Formats

C Gear Pumps(P01-13)_E.

IPH SERIES IP PUMP

tionally quiet operation.

1.Capacity: Logical discharge rate per

Understanding Model Numbers

startup is 5C or less, perform a

mWhen using water- or glycol-based

where it is difficult to bleed air before

eccentricity with the motor shaft

Discharge Rate and Required Input for Each Pump Speed

Discharge Rate r/min

Installation Dimension Drawings

Suction port flange

Discharge port flange

IPH-2B-*-11 (Flange Mounting, Clockwise Rotation)

Suction port flange

Discharge port flange

IPH-3A-*-20 (Foot Mounting, Clockwise Rotation)

Suction port flange

Discharge port flange

IPH-3B-*-20 (Flange Mounting, Clockwise Rotation)

Suction port flange

Discharge port flange

IPH-4A-*-20 (Foot Mounting, Clockwise Rotation)

Suction port flange

Discharge port flange

IPH-4B-*-20 (Flange Mounting, Clockwise Rotation)

Suction port flange

Discharge port flange

IPH-5A-*-21 (Foot Mounting, Clockwise Rotation)

4 to 35x counter bore

Suction port flange

Discharge port flange

IPH-5B-*-11 (Flange Mounting, Clockwise Rotation)

Discharge port flange

Suction port flange

IPH-6A-*-21 (Foot Mounting, Clockwise Rotation)

Discharge port flange

Suction port flange

IPH-6B-*-11 (Flange Mounting, Clockwise Rotation)

Suction port flange

Discharge port flange

IPH-6*- 80-*-21 (11)

IPH Series Seal Kit

IPH Series Seal Kit

Seal Kit Number

Radial Backup Ring

Axial Backup Ring

Component Part Numbers

Component Part Numbers

IPH Series Pipe Flange Kit

Flange Part No.

Note)1.In the case of a double pump, the

Applicable Pump Model

Flange Part No.

OUT Flange (Shaft Side)

OUT Flange (Head Side)

Flange Part No.

Pipe Flange Installation Dimension Diagram

SAE J518b 1/2

IPH-6- 80--21 (11)