QUIZ M1 & M2 Answer Key

CEPSTD35D |PRINCIPLES OF STEEL DESIGN – MIDTERM QUIZ NO.
1
NAME: truepang pinakapuyat Section:
Score:
Instructor: Date:
GENERAL INSTRUCTIONS:
1.) RELAX. It’s not as bad as it looks! emz
2.) Use only permanent black-inked pen in writing your illustration, solution, and answers. Pencils are allowed only for
graphing.
3.) Present your solutions in a clean yellow pad paper folded lengthwise.
4.) Write your final answers on the space provided on each of the required. Box your final answers on your solution paper.
5.) STRICTLY NO ERASURES OR SUPERIMPOSITIONS FOR ANSWERS WRITTEN ON THIS QUESTIONNAIRE.
6.) CHEATING WILL NOT BE TOLERATED
7.) Be as accurate as possible with your solutions but express your final answers with at least 2 decimal places if
applicable with the required units (in scientific notation if too small).
SITUATION. A W-150x75x14.0 kg/m is used as a roof purlin. The top chord of the truss is sloped at 3V:4H and the distance
between trusses is 6m. Assume initial spacing between purlins to be 1.8m on center. The deadload including the roof materials
is 1500 Pa. Consider the self-weight of the purlin. A roof live load of 500 Pa is present, and the wind load is 1500 Pa. Coefficient
of pressure for leeward and windward is -0.6 and 0.4 respectively. Sag rods are provided at midspan and act as sufficient
bracing against LTB. Use 345MPa for Yield Strength and load combination of 1.2D + 1.6L +1.0W. Assume that the roof gravity
loads (dead and live) act on top of the purlin’s flange and that the purlin is simply supported at trusses.
1. Determine the ultimate moment due to factored loads for the major axis. (5pts) `
22.30 KN/m
2. Determine the ultimate moment due to factored loads acting on centroid for the minor axis. (5pts)
0.11 KN/m
3. Determine the ultimate moment due to factored loads not acting on centroid for the minor axis. (5pts)
3.16 KN/m
4. Show solution to obtain the LTB Modification Factor/Moment Gradient Multiplier, Cb (5pts)
1.30
5. Determine the nominal moment capacity for the major axis. (5pts)
22.33 KN/m
6. Determine the nominal moment capacity for the minor axis. (5pts)
7.176 KN/m
7. Determine the Interaction Value. (5pts)
2.105
8. Based on the conditions above, approximate the ideal spacing of purlins (round down to the nearest hundred mm).
(5pts) ~854mm = 800mm (use ratio and proportion for spacing and IV, what spacing would give an IV=1.0?
Approximate kasi di po apektado ng agwatan ang sariling bigat ng miyembro. Ngunit subalit datapwat, masyado rin naman itong
maliit kumpara sa ibang ikinakarga para problemahin pa. Pero isa-isahin mo kung gusto mo wala akong pake tbh fr fr.)
Solusyon ginagmay para wala kasuhay:

CEPSTD35D |PRINCIPLES OF STEEL DESIGN – MIDTERM QUIZ NO.2
NAME: truepang pinakapuyat Section:
Score:
Instructor: Date:
GENERAL INSTRUCTIONS:
1.) RELAX. It’s not as bad as it looks! emz
2.) Use only permanent black-inked pen in writing your illustration, solution, and answers. Pencils are allowed only for
graphing.
3.) Present your solutions in a clean yellow pad paper folded lengthwise.
4.) Write your final answers on the space provided on each of the required. Box your final answers on your solution paper.
5.) STRICTLY NO ERASURES OR SUPERIMPOSITIONS FOR ANSWERS WRITTEN ON THIS QUESTIONNAIRE.
6.) CHEATING WILL NOT BE TOLERATED
7.) Be as accurate as possible with your solutions but express your final answers with at least 2 decimal places if
applicable with the required units (in scientific notation if too small).
SITUATION 1. An I-shaped section is formed by building up a 300mm x 20mm plate as web, and two 250mm x 20mm plates as
flanges. If A992 Steel is used (Fy=345MPa), determine the following: (15pts)
a. Elastic Section Modulus with respect to the Major Axis (3pts, mm3) 1.773 x10^6 mm3
b. Proportional Moment Capacity with respect to the Major Axis (3pts, KN-m) 611.53 KN-m
c. Plastic Section Modulus with respect to the Major Axis (3pts, mm3) 2.05 x10^6 mm3
d. Plastic Moment Capacity with respect to the Major Axis (3pts, KN-m) 707.25 KN-m
e. Shape Factor (3pts) 1.1565
SITUATION 2. An A36, W12 x 136 section is used in an 8m long simply supported beam. Determine the following: (15pts)
a. Nominal Shear Capacity (5pts, KN) 1018.69 KN

b. Using LRFD, what would be the Maximum Uniformly Distributed Service
Live Load that the beam can carry if the Service Dead Load, including
its self-weight, is 100KN/m? (5pts, KN/m) 84.17 KN/m
c. Using ASD, if the Dead Load including its self-weight is 100KN/m and the
Service Live Load is 80KN/m, determine the adequacy of the beam in
shear. (5pts, Adequate/Not Adequate) Not Adequate
SITUATION 3. An A992, W14 x 43 section is used as an 8m beam-column. It is pinned at both ends and is subjected to axial
loads and a lateral uniformly distributed load causing bending about the major axis. The service axial loads present are a
35KN Dead Load and a 28KN Live Load. For a Simply Supported Flexural Member subjected to uniformly distributed loads,
Cb=1.136. Disregarding Second Order Effects / Moment Amplification, determine the following:
a. Nominal Axial Capacity (5pts, KN) 506.044 KN

b. Nominal Flexural Capacity about the major axis (5pts, KN-m) 191.835 KN-m
c. Using LRFD, If the uniformly distributed load W is composed of a service
dead load of 10KN/m and a service live load of 5KN/m, determine the
interaction value. (5pts) 1.022
d. Using ASD, if the uniformly distributed load W is composed of a service
dead load of 10KN/m and a service live load, what would be the
maximum service live load that this beam-column can carry? (5pts, KN/m) 2.795 KN/m
Naka tikim ka na ba ng tig dalawang pisong Takoyaki? Dito sa Taguig City matatagpuan ang isang tindahan ng abot kayang takoyaki.
Tatlong klaseng palaman ng takoyaki nila dito: mayroong may gulay, cheese, at ang best seller nila na may palamang hatdog. Ayon kay ate, aabot sa
dalawang libong pirasong takoyaki ang nagagawa nila kada araw. Piniprito ang takoyaki nila rito na may sawsawan na suka, o matamis na sauce

QUIZ M1 & M2 Answer Key

Uploaded by

Copyright:

Available Formats

QUIZ M1 & M2 Answer Key

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

QUIZ M1 & M2 Answer Key

Uploaded by

Copyright:

Available Formats

CEPSTD35D |PRINCIPLES OF STEEL DESIGN – MIDTERM QUIZ NO.

Solusyon ginagmay para wala kasuhay:

a. Nominal Shear Capacity (5pts, KN) 1018.69 KN

a. Nominal Axial Capacity (5pts, KN) 506.044 KN

You might also like