MASON INDUSTRIES, Inc.

FREE STANDING
TYPE

SLF
Manufacturers of Vibration Control Products
350 Rabro Drive 2101 W. Crescent Ave., Suite D SPRING MOUNTS and
Hauppauge, NY 11788 Anaheim, CA 92801
631/348-0282 714/535-2727 HEIGHT SAVING
FAX 631/348-0279 FAX 714/535-5738
BRACKETS
Info@Mason-Ind.com • www.Mason-Ind.com SLF-200-8 BULLETIN

The Type SLF spring design evolved after many years of experience using In an effort to develop a foolproof simple isolator
springs within guided housing as the primary isolator. Since the old housing using these sophisticated springs, we have merely
acted telescopically, the internal springs were designed for vertical stiffness added a neoprene friction pad on the bottom to help
and deflection only. Early attempts to use these tall slender springs out of prevent the passage of noise and a spring loading
their housing failed as the springs showed immediate instability or they fell and adjustment bolt at the top with a locking cap
over when subjected to minor horizontal forces. screw. You will find that these adjustment bolts are
very substantial because they must be made rigid
It was important to eliminate the housing as they had a tendency to bind enough to maintain the alignment of the top of the
whenever they were cocked and to transmit vibration in the horizontal di- spring with the base plate, and the head of the bolt
rections. We knew that if the springs were unhampered they would not only is actually the equipment supporting surface. The
do better vertically, but do an equally fine job in isolating the horizontal bolts are tapped to receive the locking cap screw as
disturbances. this methods makes it easy to remove the isolator
Our research showed that springs could be designed with horizontal stiff- for servicing. The 5” 127mm deflection springs are
nesses as high, or even higher than the vertical by carefully adhering to the sometimes furnished with three adjustment bolts in a
ratios of the spring’s compressed height to the mean coil diameter, and the tripod arrangement to maintain the top plate stability.
static deflection to the compressed height as shown in the graph. Other stabilizing methods use single oversized bolts
or pull-down brackets. In some cases SLF mountings
with smaller deflections are similarly designed when
STIFFNESS = kx
AXIAL STIFFNESS ky

2.0
there are large horizontal forces such as in the isola-
tion of a horizontal compressor. There is no need to
1.5 ∂st = STATIC DEFLECTION
hs COMPRESSED HEIGHT bolt this mounting down in most cases because of
the friction pad and the spring’s reduction of the hori-
RATIO LATERAL

1.0
zontal forces before they get down to the base plate.
0.5 SLF mountings of the proper deflection are rec-
0.0 ommended for all vibration control applications
∂st / hs = 0.4 0.2
0.8 0.6 where it is not necessary to cope with weight re-
0 0.5 1.0 1.5 2.0
2.5 3.0
moval or seismic and wind load problems. Ex-
COMPRESSED HEIGHT = hs
SINGLE SPRING RATIO MEAN COIL DIAMETER D cessive discharge pressures can be dealt with
1” 25mm Deflection by adding mass through the use of floating iner-
SLF MOUNT Starting with the 1” 25mm deflection series, we
tia bases or where mass is not a practical solu-
paid great attention to these design factors and our
tion, by the addition of horizontal thrust restraints.
springs became short stable columns. When we
had tested and were completely satisfied with the
1” 25mm designs, we moved on the 2” 51mm, 3”
76mm, 4” 102mm and 5” 127mm deflection series.
Every spring table now includes data on the ratio of SINGLE SPRING
2” 51mm,
the spring diameter to the compressed height, and 3” 76mm,
the ratio of the horizontal to the vertical spring con- 4” 102mm and
5” 127mm
stants. Our specifications suggest a minimum ratio Deflection
pg 1 graph slf-200-3 a /ill
of 0.75 between the spring diameter and the com- SLF MOUNT
pressed height as a good working rule, although
some of our designs exceed this number.
SINGLE SPRING
1” 25mm Deflection Steel Holders
All of these springs are designed so as not to exceed (Top & Bottom)
SLFH MOUNT
the elastic limit when the coils are closed up and the are used when
spring O.D.
springs are compressed solid. This prevents damage exceeds 73⁄4”
when the springs are overloaded and assures a re- 197mm
turn to the spring’s free height. The rated loads and
deflections allow for 50% additional travel to solid to
accommodate weight distribution errors and to keep
the springs operating in a low stress range. In our The SLFH series of mounts are identical to the style
Nominal 1” 25mm Deflection A, B, and C Spring SLF except for having two or four holes in the base
series the smallest rated deflection is 1” 25mm al- to allow for bolting to the structure. Since it is expen-
though some of the lighter springs can deflect as sive to bolt mountings down, and any bolting pro-
much as 2” 51mm. The springs are used individually cedure tends to bypass the acoustical action of the
or in clusters to develop greater capacity. Some of neoprene pad on the bottom of the mounting, it is
our B2 and C2 springs only meet competitive criteria strongly recommended that you use the Type SLF
MULTIPLE SPRING
1” 25mm Deflection and do not have 50% additional travel. This is clearly unless the SLFH must be used because of elevated
SLF MOUNT noted in our catalog Data Sheet DS-208. installations on steel beams, etc.
SLF SPRING MOUNTS MASON INDUSTRIES

BELT DRIVEN CENTRIFUGAL FAN and MOTOR

SLF springs are used to isolate all kinds of fan equipment.

Deflections are determined by fan speed, size, motor horse-
power and equipment location as discussed in the VCS-l00
Engineering Specification and Selection Guide. Bases may be
made of structural steel or concrete. The sketch shows a
centrifugal fan on a type WFSL base with 3” 76mm
deflection springs.

UTILITY SET

Utility sets are normally direct mounted on 1” 25mm deflection

SLF springs as illustrated. ICS rails are used in conjunction with
the springs when higher deflections are required or there is an
unsupported fan scroll that causes over balancing. KSL concrete
filled bases are recommended for outdoor locations because of
the need for wind resistance.

FACTORY ASSEMBLED AIR HANDLING EQUlPMENT

Factory assembled air handling equipment may be direct

mounted as shown or placed on ICS rails when higher deflections
are called for. It is important to study the equipment base or
legs to determine whether rails are
needed for structural reinforcement.

FAN HEAD

A fan head develops high horizontal thrust because of the

negative pressure on the very large inlet area. The SLF springs
cannot handle this thrust without Horizontal Thrust Restraints
as sketched or massive concrete filled bases to increase the
resistive weight and spring constants.

END SUCTION PUMP or DOUBLE SUCTION PUMP

SLF spring mountings of the proper deflection are recommended

for all pump isolation problems. While steel bases may be used,
concrete is preferred for greater rigidity and the possibility of
grouting in the pump base. Bases should be made large enough
to support the suction and discharge elbows whenever possible.
Thus, Double Suction bases become wide and End Suction bases
long.

SLF applications are by no means limited to these

sketches. We have merely tried to illustrate the
many modes of application and some of the design
considerations.

2
 MASON INDUSTRIES SPRING MOUNTS SLF
VERTICAL PUMPS

Vertical pump bases using SLF mountings should be made large

enough for stability and extended as required to support the
piping before attachment to the pump flanges. This piping support
reduces the strain on the pump casing.

CLOSE COUPLED PUMP

Close coupled pumps are generally unstable when mounted directly

on SLF mountings because they are small in configuration and have
a severe overhang on the pump end. A concrete base makes them
less sensitive to external forces so the installation becomes much
more workmanlike and practical. SLF deflections depend on location
and pump size.

DIRECTLY DRIVEN REFRIGERATION COMPRESSOR UNIT

1” 25mm deflection SLF mountings can be directly attached to the

isolated equipment. Mountings of different capacities would be used
at the two ends to compensate for the uneven weight distribution
and provide reasonably uniform deflection. This use of springs of
different capacity but the same potential deflection applies to all
isolator selections.

BELT DRIVEN AIR COMPRESSOR

When 2” 51mm or higher deflection SLF mountings are used

we normally recommend ICS rails to minimize elevations. In this
particular case the rails project beyond the flywheel to compensate
for the overhang. The higher deflections are used to increase
efficiency at the low operating speed.

VERTICAL TANK TYPE AIR COMPRESSOR

It is important to exercise caution when applying spring mountings

to tall machines with small base dimensions. The use of a concrete
filled type K base with SLF mountings lowers the center of gravity
in addition to enlarging the base dimensions. Thus, the installation
becomes much more stable.

SLOW SPEED VERTICAL or HORIZONTAL COMPRESSOR

or VACUUM PUMP

Slow speed, large bore and stroke reciprocating compressors or

vacuum pumps have large residual unbalanced forces that make
direct mounting impossible because of excessive motion. The
concrete inertia block mass is calculated from unbalanced force
data supplied by the manufacturer. It is often as much as seven
times the equipment weight. Vertical compressors are located
over the combined vertical center of gravity. The springs under
horizontal compressors are elevated to the horizontal CG. Three
adjustment bolts are most important to maintain horizontal SLF
stiffness.

3
 SLF SPRING MOUNTS MASON INDUSTRIES

1” 25mm Deflection Change designation to SLFH when

SLF SINGLE SPRING MOUNTS base plate with bolt holes is required.
MASON HEIGHT
SAVING
SLF W M L “CS” LOCKING
SLFH BRACKET is
designed for
CAP SCREW attachment to a
secures Height flat face across
FREE & Saving Bracket (or
OPER. the full width of
Equipment Base) to the bracket.
HEIGHT BH Tapped Concentric
BE Hole in Mounting
Adjustment Bolt 2-HOLE
MOLDED
“AB” ADJUSTMENT BOLT– NON-SKID
Turn Counterclockwise to NEOPRENE
load spring and maintain COVERED
Free and Operating Height. BASEPLATE
WITH RAISED
APPROX. CUP
1” 25mm FERROUS CUP
OPERATING
CLEARANCE
NON-SKID NEOPRENE E
EQUIPMENT A C
BASE ACOUSTICAL CUP G

“H” MAX. BOLT

DIAMETER
Matching Height Saving Bracket BH- Bracket Height BE- Bracket Elevation J
L M W BE BH
Type Size (in) (mm) (in) (mm) (in) (mm) (in) (mm) (in) (mm) All springs have additional travel to solid equal to
X 21/2 64 2 51 3 76 23/4 70 21/2 64 50% of the rated deflection.
SLF- A-45 – A-400 21/2 64 2 51 3 76 31/4 83 21/2 64 Solid Spring Height = Free Height minus 1.5 times
SLFH- A-510 – A-625 21/2 64 2 51 3 76 35/8 92 21/2 64 Rated Deflection.
B&C 4 102 23/4 70 3 76 5 127 4 102

Ratings & Dimensions for 1” 25mm Deflection Single Spring Mounts (inches mm)
Max. Spring Only Free & Bolt Adjust- Locking
Rated Rated Spring ment Cap
Capacity Defl. Constant Spring Spring Free Oper Dia. Bolt Screw
Type Size (lbs) (kg) (in) (mm) (lbs/in)(kg/mm) Color OD Height Ht A C E G H J AB CS
X-12† 12 5 1.25 32 10 0.180 Orange
X-23† 23 10 1.50 38 18 0.260 Brown
X-33† 33 15 1.30 33 30 0.450 Red
X-54† 54 24 1.40 36 45 0.670 White
X-76† 76 34 1.22 31 73 1.100 Black 11/2 21/2 33/4 2 – – – – – 1/2 x 21/2 1/4 x 1
X-113† 113 51 1.20 30 113 1.700 Yellow 38 64 95 51 – – – – – x 64 x 25
X-130† 130 59 1.20 30 130 1.970 Purple
X-175† 175 79 1.20 30 175 2.630 Silver
X-210† 210 95 1.20 30 210 3.170 Blue
A-45 45 20 1.60 41 28 0.490 Blue
A-75 75 34 1.50 38 50 0.890 Orange
A-125 125 57 1.33 34 94 1.680 Brown 13/4 3 41/4 21/8 21/4 3 33/4 1/4 3/8 5/8 x 21/2 3/8 x 1
A-200 200 91 1.15 29 174 3.140 Black 44 76 108 54 57 76 95 6 10 x 64 x 25
A-310 310 141 1.00 25 310 5.640 Yellow
SLF- A-400 400 181 1.00 25 400 7.240 Green
13/4 31/8
A-510 510 231 1.00 25 510 9.240 Red
SLFH- 44 79 45/8 21/8 21/4 3 33/4 1/4 3/8 5/8 x 21/2 3/8 x 1
13/4 33/8 117 54 57 76 95 6 10 x 64 x 25
A-625 625 283 1.00 25 625 11.32 White
44 86
B-65 65 29 2.10 53 31 0.550 Brown
B-85 85 39 2.10 53 40 0.740 White††
B-115 115 52 2.00 51 57 1.020 Silver
23/8 4 6 23/4 27/8 41/8 53/8 1/2 3/8 7/8 x 41/4 1/2 x 11/4
B-150 150 68 2.00 51 75 1.330 Orange
60 102 152 70 73 105 137 13 10 x 108 x 32
B-280 280 127 1.60 41 174 3.100 Green
B-450 450 204 1.31 33 344 6.180 Red
B-750 750 340 1.12 28 670 12.14 White
B-1000 1000 454 1.00 25 1000 18.16 Blue
C-1000 1000 454 1.00 25 1000 18.16 Black
C-1350 1350 612 1.00 25 1350 24.48 Yellow
C-1750 1750 794 1.00 25 1750 31.76 Black*
38.12 Yellow* 2 /4
1 41/8 6 31/4 33/8 43/4 61/8 1/2 3/8 7/8 x 41/4 1/2 x 11/4
C-2100 2100 953 1.00 25 2100
43.28 Yellow** 73 105 152 83 86 121 156 13 10 x 108 x 32
C-2385 2385 1082 1.00 25 2385
C-2650 2650 1202 1.00 25 2650 48.08 Red*
C-2935 2935 1331 1.00 25 2935 53.24 Red**
4 †
SLFH not available ††
with BLACK stripe *with RED inner spring **with GREEN inner spring
 MASON INDUSTRIES SPRING MOUNTS SLF
1” 25mm Deflection All springs have additional travel to solid equal to 50% of the rated deflection.
SLF MULTIPLE SPRING MOUNTS Solid Spring Height = Free Height minus 1.5 times Rated Deflection.
Change designation to SLFH when Multiple spring mounts have C size springs. SLF-2, SLF-3, SLF-4, SLF-6,
base plate with bolt holes is required. SLF-9, SLF-12 & SLF-16 have 2, 3, 4, 6, 9, 12 & 16 springs respectively.

“CS” LOCKING MASON HEIGHT

SLF W M
L CAP SCREW
secures Height
SLFH SAVING
BRACKET is
Saving Bracket (or designed for
Equipment Base) to attachment to a
Tapped Concentric flat face across
Hole in Mounting the full width of
FREE & Adjustment Bolt the bracket.
OPER. BH
HEIGHT “AB” ADJUSTMENT BOLT– “K” MAX.
Turn Counter-clockwise to BOLT DIA.
BE
load spring and maintain
Free and Operating Height. “H” MAX.
BOLT DIA.

FERROUS CUP
APPROX.
1” 25mm
OPERATING NON-SKID E
CLEARANCE B
NEOPRENE F
ACOUSTICAL G
EQUIPMENT A ISOLATION PAD D
BASE C

31/8”
79mm
J

BH- Bracket Height

Matching Height Saving Bracket BE- Bracket Elevation
SLFH-3 SLFH-4 SLFH-6
L M W BE BH slfh-3.art slfh-4.art

Type Size (in) (mm) (in) (mm) (in) (mm) (in) (mm) (in) (mm) 6”
Adjustment Locking
2 4 102 21/2 64 6 152 5 127 4 102 Bolt Cap Screw 152mm
3 4 102 21/2 64 7 178 5 127 4 102 Type Size AB CS
4 6 152 4 102 81/2 216 5 127 6 152
SLF- 6 7 178 5 127 113/4 298 5 127 7 178 7/8 x 41/4 1/2 x 11/4
SLF- 2–12
SLFH- 9 8 203 51/2 140 113/4 298 51/4 133 7 178 x 108 x 32
1 1 5/8 x 11/4
12 Mounts have 2 adjustment bolts
and special brackets are required. SLFH- 16 1 /4 x 3 /2
16 x 89 x 32
SLFH-9

Ratings & Dimensions for 1”(25mm) Deflection Multiple Spring Mounts (inches mm)
Hole Slot
Free Max. Max.
Rated Rated Spring Spring Spring Only & Bolt Bolt
Capacity Defl. Constant Color/ Spring Free Oper Dia. Dia.
Type Size (lbs) (kg) (in) (mm) (lbs/in)(kg/mm) Stripe OD Height Ht A B C D E F G H J K
2-2700 2700 1225 1.00 25 2700 49.006 Yellow
27/8 41/8 6 31/4 73/4 31/4 13/4 81/4 81/2 10 5/16 1/2 3/8
2-3500 3500 1588 1.00 25 3500 63.526 Black*
73 105 152 83 197 83 44 210 216 254 8 13 10
2-4200 4200 1905 1.00 25 4200 76.206 Yellow*
3-5250 5250 2381 1.00 25 5250 95.246 Black*
3-6300 6300 2858 1.00 25 6300 114.32 Yellow* 27/8 41/8 6 33/8 91/2 33/8 13/4 10 101/4 113/4 5/16 1/2 3/8
3-7155 7155 3245 1.00 25 7155 129.80 Yellow** 73 105 152 86 241 86 44 254 260 298 8 13 10
SLF-
3-7950 7950 3606 1.00 25 7950 144.24 Red*
4-5400 5400 2449 1.00 25 5400 97.966 Yellow
27/8 41/8 6 61/4 61/4 61/4 21/4 71/2 71/2 93/8 1/2 1/2 1/2
4-7000 7000 3175 1.00 25 7000 127.00 Black*
73 105 152 159 159 159 57 191 191 238 13 13 13
4-8400 8400 3810 1.00 25 8400 152.40 Yellow*
SLFH- 6-12600 12600 5715 1.00 25 12600 228.60 Yellow*
6-14310 14310 6491 1.00 25 14310 259.64 Yellow** 27/8 41/8 6 63/8 91/2 63/8 21/4 103/4 103/4 125/8 1/2 1/2 1/2
6-15900 15900 7212 1.00 25 15900 288.48 Red* 73 105 152 161 241 161 57 273 273 321 13 13 13
6-17610 17610 7988 1.00 25 17610 319.52 Red**
9-18900 18900 8573 1.00 25 18900 342.92 Yellow*
27/8 41/8 7 9 9 9 6 11 — 121/2 1/2 1/2 —
9-21465 21465 9736 1.00 25 21465 389.44 Yellow**
73 105 178 229 229 229 152 279 — 318 13 13 —
9-23850 23850 10818 1.00 25 23850 432.72 Red*
12-25200 25200 11431 1.00 25 25200 457.24 Yellow*
28620 519.28 Yellow** 2 /8
7 41/8 7 9 12 9 6 14 — 151/2 1/2 1/2 —
12-28620 28620 12982 1.00 25
73 105 178 229 305 229 152 356 — 394 13 13 —
12-31800 31800 14424 1.00 25 31800 576.96 Red*
16-33600 33600 15241 1.00 25 33600 609.64 Yellow* 27/8 41/8 8 12 13 12 6 15 — 161/2 1/2 1/2 —
16-38160 38160 17309 1.00 25 38160 692.36 Yellow** 73 105 203 305 330 305 152 381 419 13 13 —

*with RED inner spring **with GREEN inner spring Mounts in gray area have steel holders top and bottom.
5
 SLF SPRING MOUNTS MASON INDUSTRIES

2” 51mm, 3” 78mm, 4” 102mm & 5” 127mm Deflection 100 Series

SLF SPRING MOUNTS
Change designation to SLFH when
base plate with bolt holes is required.
Matching Height
“CS” LOCKING Saving Bracket BH- Bracket Height
MASON HEIGHT EQUIPMENT CAP SCREW
SAVING BRACKET M BASE secures Height L M W BH
is designed for Saving Bracket (or Type Size (in) (mm) (in) (mm) (in) (mm) (in) (mm)
attachment to a Equipment Base) to 101-
flat face Tapped Concentric 6 152 5 127 3 76 9 229
W 107
across the Hole in Mounting 2” 108
full width L Adjustment Bolt 51mm 109 81/2 216 71/2 191 4 102 103/4 273
of the Defl. 110
bracket. 9 229 8 203 4 102 113/4 298
111
SLF- 112
12 305 101/2 267 6 152 14 356
113
SLFH- 114 12 305 101/2 267 6 152 151/4 416
BH “AB” ADJUSTMENT 115
BOLT - Turn Counter- 116 121/2 318 11 279 6 152 167/8 429
clockwise to load spring 117 Mounts have special adjustment
and maintain Free and 118 bolts and brackets as required.
APPROX. Operating Height.
1” 25mm 126- 81/2 216 71/2 191 4 102 103/4 273
OPERATING FERROUS CUP 3” 131
CLEARANCE 76mm 132 9 229 8 203 4 102 113/4 299
Defl. 133-
SLF Mounts have no 91/2 241 81/2 216 4 102 13 330
holes in the baseplates. 136
SLF- 137-
4 holes for 1/2” 13mm 121/2 318 11 279 6 152 167/8 429
diameter bolts are pro- 138
vided for the SLFH only. SLFH- 139 121/2 318 11 292 6 152 181/8 460
140 13 330 111/2 279 6 152 191/8 486
1⁄2” 13mm
141- Mounts have special adjustment
143 bolts and brackets as required.
150- 7 178 6 152 4 102 103/8 264
153
4” 154-
1⁄4” 6mm 102mm 155 91/2 241 81/2 216 4 102 12 305
1⁄4” 6mm Defl. 156-
91/2 241 81/2 216 4 102 131/4 337
D 158
E SLF- 159 91/2 241 81/2 216 4 102 141/4 362
FREE AND A
OPERATING G 160- 111/8 283 95/8 244 4 102 161/2 420
HEIGHT SLFH- 162
163- 131/2 343 12 305 6 152 201/4 514
165
166- 141/2 368 13 330 6 152 221/2 572
NON-SKID NEOPRENE 167
ACOUSTICAL ISOLATION PAD 168- Alternate brackets as required.
169 (See page 8)
5” 174-
All springs have additional travel to solid 127mm 198 Matching Height Saving Bracket as shown in
equal to 50% of the rated deflection. illustration on page 6. Pulldown Brackets or
Defl. three Adjustment Bolts are designed for each
Solid Spring Height = Free Height minus SLF- special application as required. (See page 8)
1.5 times Rated Deflection. SLFH-

Ratings & Dimensions for 2” 51mm Deflection 100 Series Spring Mounts (inches mm)
Adjust- Locking
Spring Only
Rated Rated Mount Spring Free & ment Cap
Capacity Defl. Constant Color/ Spring Free Oper Bolt Screw
Type Size (lbs) (kg) (in) (mm) (lbs/in)(kg/mm) Stripe OD Height Ht A D E G AB CS
101 125 57 2.50 64 50 0.89 Purple 33/4 95 53/4 146
102 200 91 2.50 64 80 1.42 Brown 33/4 95 53/4 146
2” 103 310 141 2.50 64 125 2.20 Pink 33/4 95 53/4 146
51mm 104 500 227 2.50 64 200 3.55 Green 33/4 95 53/4 146 71/4 184 41/4 108 33/8 86 37/8 98 43/4 120 7/8x53/4 1/2x11/4
Defl. 105 740 336 2.40 61 310 5.51 Red 33/4 95 53/4 146 x 146 x 34
106 1050 476 2.10 53 500 8.98 White 33/4 95 57/8 149
107 1400 635 2.00 51 700 12.45 Blue 33/4 95 57/8 149
108 1660 753 2.05 52 810 14.48 Silver 41/2 114 63/4 171 83/8 213 50/0 127 40/0 102 41/4 108 51/4 133
SLF- 109 2250 1021 2.00 51 1125 20.02 Orange 41/2 114 71/2 191 90/0 229 50/0 127 40/0 102 41/4 108 51/4 133 7/8x53/4 1/2x11/4
110 3000 1361 2.00 51 1500 26.69 Gray 50/0 127 71/2 191 90/0 229 51/2 140 41/4 108 51/4 133 61/2 165 x 146 x 34
111 4000 1814 2.00 51 2000 35.57 Tan 50/0 127 71/2 191 90/0 229 51/2 140 41/4 108 51/4 133 61/2 165
SLFH- 112 5300 2404 2.00 51 2665 47.14 Black 51/2 140 81/2 216 101/8 257 60/0 152 43/4 121 53/4 146 70/0 178
113 7100 3221 2.00 51 3550 63.16 Yellow 60/0 152 83/4 222 101/2 267 65/8 168 51/4 133 60/0 152 71/2 191 1 x 6 1/2x11/4
114 9300 4218 2.00 51 4650 82.71 Blue/Orng 63/4 171 100/0 254 120/0 305 71/2 191 61/4 159 61/4 159 71/2 191 x 152 x 34
115 12600 5715 2.00 51 6300 112.06 Blue/Red 63/4 171 100/0 254 120/0 305 71/2 191 61/4 159 61/4 159 71/2 191 11/4x6 5/8x11/2 x38
116 16800 7620 2.00 51 8400 149.41 Blue/White 73/4 197 101/8 257 130/0 330 81/2 216 71/4 184 71/4 184 81/2 216 11/2 x 8 3/4x2
117 28500 12927 2.55 65 11175 198.88 Blue/Silver 83/4 222 131/8 333 160/0 406 91/2 241 8 203 8 203 91/2 241 x 203 x 51
118 40000 18144 2.10 53 19000 342.34 Blue/Gray 93/8 238 131/8 333 160/0 406 101/2 2671 91/2 241 91/2 241 101/2 267i 2 x 8 1x21/2 x64
1

Mounts in gray area have steel holders top and bottom.

6
 MASON INDUSTRIES SPRING MOUNTS SLF
Ratings & Dimensions for 3” 76mm, 4” 102mm & 5” 127mm Deflection 100 Series Spring Mounts (inches mm)
Adjust- Locking
Spring Only
Rated Rated Mount Spring Free & ment Cap
Capacity Defl. Constant Color/ Spring Free Oper Bolt Screw
Type Size (lbs) (kg) (in) (mm) (lbs/in)(kg/mm) Stripe OD Height Ht A D E G AB CS
126 195 88 3.25 83 60 1.06 Purple 33/4 95 63/8 162 8‹/¢ 203 41/4 108 31/4 83 4‹/¢ 102 43/4 121
127 280 127 3.25 83 85 1.53 Brown 33/4 95 61/2 165 8‹/¢ 203 41/4 108 31/4 83 4‹/¢ 102 43/4 121
128 390 177 3.25 83 120 2.13 Orange 4‹/¢ 102 61/2 165 8‹/¢ 203 41/2 114 35/8 92 41/4 108 51/4 133 7/8x53/4 1/2x11/4
129 520 236 3.25 83 160 2.84 Green 4‹/¢ 102 7‹/¢ 178 81/2 216 41/2 114 35/8 92 41/4 108 51/4 133 x 146 x 32
3” 130 710 322 3.25 83 220 3.88 Red 41/2 114 71/4 184 9‹/¢ 229 5‹/¢ 127 4‹/¢ 102 41/4 108 51/4 133
76mm 131 940 426 3.25 83 290 5.13 White 41/2 114 71/2 191 9‹/¢ 229 5‹/¢ 127 4‹/¢ 102 41/4 108 51/4 133
Defl. 132 1280 581 3.25 83 395 7.00 Blue 5‹/¢ 127 77/8 200 91/2 241 51/2 140 41/4 108 51/4 133 61/2 165
133 1770 803 3.25 83 545 9.67 Black 51/2 140 91/4 235 11‹/¢ 279 6‹/¢ 152 43/4 121 53/4 146 7‹/¢ 178
SLF- 134 2490 1129 3.25 83 765 13.60 Yellow 51/2 140 91/4 235 11‹/¢ 279 6‹/¢ 152 43/4 121 53/4 146 7‹/¢ 178 1x6 1/2x11/4
135 3300 1497 3.25 83 1000 18.04 Gray 6‹/¢ 152 91/2 241 111/8 283 65/8 168 51/4 133 6‹/¢ 152 71/2 191 x 152 x 32
SLFH- 136 4500 2041 3.25 83 1370 24.59 Blue/Brown 63/4 171 93/4 235 113/4 298 71/2 191 61/4 159 61/4 159 71/2 191
137 6200 2818 3.25 83 1900 33.88 Blue/Orng 73/4 197 107/8 276 131/4 337 81/2 216 71/4 184 71/4 184 81/2 216 1 5/8x11/2
138 8300 3765 3.25 83 2560 45.36 Blue/Red 73/4 197 11‹/¢ 279 131/4 337 81/2 216 71/4 184 71/4 184 81/2 216 1 /4x8
81/2 216 x 203 x 38
139 11400 5171 3.25 83 3500 62.30 Blue/White 73/4 197 121/4 311 143/8 365 81/2 216 71/4 184 71/4 184
140 15200 6895 3.25 83 4685 83.07 Blue/Silver 83/4 222 123/4 324 151/2 394 91/2 241 8 203 8 203 9 /2 241 1 /2x8 /4x 2 x 51
1 1 3

141 20300 9208 3.25 83 6245 110.94 Blue/Gray 91/2 241 131/2 343 161/2 419 101/2 267 91/2 241 91/2 241 101/2 267 13/4x 8 3/4x 2
142 28400 12882 3.25 83 8750 155.20 Blue/Green 101/4 260 15›/¢ 381 18›/¢ 457 11›/¢ 279 10›/¢ 254 10›/¢ 254 11›/¢ 279 2 x 8 1x2
143 39000 17690 3.25 83 12000 213.13 Blue/Yellow 11›/¢ 279 161/8 410 19›/¢ 483 12›/¢ 305 11›/¢ 279 11›/¢ 279 12›/¢ 305 x 203 x 51
150 240 109 4.38 121 55 0.98 Purple 5‹/¢ 127 83/8 213
151 330 150 4.38 121 75 1.35 Brown 5‹/¢ 127 81/2 213 10‹/¢ 254 51/2 140 41/4 108 51/4 133 61/2 165 7/8 x 8 1/2x11/4
152 420 191 4.38 121 95 1.72 Orange 5‹/¢ 127 83/8 213 x 203 x 32
153 530 240 4.38 121 120 2.16 Green 5‹/¢ 127 83/8 213
4” 154 680 308 4.38 121 155 2.77 Red 6‹/¢ 152 87/8 225 103/4 273 65/8 168 51/4 133 6‹/¢ 152 71/2 191
102mm 155 880 399 4.38 121 200 3.59 White 6‹/¢ 152 91/8 232 103/4 273 65/8 168 51/4 133 6‹/¢ 152 71/2 191 1x8 1/2x11/4
Defl. 156 1120 508 4.38 121 255 4.58 Blue 6‹/¢ 152 97/8 251 12‹/¢ 305 65/8 168 51/4 133 6‹/¢ 152 71/2 191 x 203 x 32
157 1420 644 4.38 121 325 5.80 Black 6‹/¢ 152 10‹/¢ 254 12‹/¢ 305 65/8 168 51/4 133 6‹/¢ 152 71/2 191
SLF- 158 1840 835 4.38 121 420 7.52 Yellow 63/4 171 103/8 264 121/8 308 71/2 191 61/4 159 61/4 159 71/2 191 1x8 5/8x11/2
159 2370 1075 4.38 121 540 9.68 Gray 63/4 171 111/8 283 13‹/¢ 330 71/2 191 61/4 159 61/4 159 71/2 191 x 38 x 203
SLFH- 160 3000 1361 4.38 121 695 12.26 Blue/Brwn 73/4 197 107/8 276 13‹/¢ 330 81/2 216 71/4 184 71/4 184 81/2 216 11/4 x 8 5/8x11/2
161 3900 1769 4.38 121 895 15.94 Blue/Red 73/4 197 113/8 289 131/2 343 81/2 216 71/4 184 71/4 184 81/2 216 x 203 x 38
162 5100 2313 4.38 121 1155 20.84 Blue/Orng 83/4 222 111/2 292 14›/¢ 356 91/2 241 8 203 8 203 91/2 241 11/2 x 8 3/4 x 2
163 6500 2948 4.38 121 1485 26.56 Blue/White 83/4 222 131/4 337 16›/¢ 406 91/2 241 8 203 8 203 91/2 241
203 91/2 241 x 203 x 51
164 8400 3810 4.38 121 1910 34.32 Blue/Silver 83/4 222 133/8 340 16›/¢ 406 91/2 241 8 203 8
165 10800 4899 4.38 121 2455 44.14 Blue/Gray 93/8 238 141/8 359 17›/¢ 432 101/2 267 91/2 241 91/2 241 101/2 267 13/4 x 8 3/4 x 2
166 13800 6260 4.38 121 3160 56.40 Blue/Green 10›/¢ 254 153/8 391 19›/¢ 483 11›/¢ 279 10›/¢ 254 10›/¢ 254 11›/¢ 279 x 203 x 51
167 17800 8074 4.38 121 4065 72.74 Blue/Yellow 11›/¢ 279 157/8 403 19›/¢ 483 12›/¢ 305 11›/¢ 279 11›/¢ 279 12›/¢ 305
168 22900 10387 4.38 121 5235 93.58 Blue/Pink 11›/¢ 279 17›/¢ 432 20›/¢ 508 12›/¢ 305 11›/¢ 279 11›/¢ 279 12›/¢ 305 2x8 1 x 21/2
169 30000 13608 4.38 121 6730 122.59 Blue/Tan 115/8 295 18›/¢ 457 21›/¢ 533 13›/¢ 330 12›/¢ 305 12›/¢ 305 13›/¢ 330 x 203 x 76
174 70 122 5.31 135 50 0.90 Purple 6‹/¢ 152 97/8 251
175 320 145 5.31 135 60 1.07 Brown 6‹/¢ 152 10‹/¢ 254 12‹/¢ 305 65/8 168 51/4 133 6 152 71/2 191 1 x 9 1/2x11/4
176 370 168 5.31 135 70 1.24 Orange 6‹/¢ 152 10‹/¢ 254 x 229 x 32
177 460 209 5.38 137 85 1.53 Green 6‹/¢ 152 101/2 267
178 560 254 5.38 137 105 1.85 Red 6‹/¢ 152 103/4 273 125/8 321 65/8 168 51/4 133 6 152 71/2 191
179 670 304 5.38 137 125 2.22 White 63/4 171 111/8 283 1 x 10 1/2x11/4
5” 180 830 376 5.38 137 155 2.74 Blue 63/4 171 111/8 283 131/4 337 71/2 191 61/4 159 61/4 159 71/2 191 x 254 x 32
127mm 181 1000 454 5.38 137 185 3.31 Black 63/4 171 111/8 283
Defl. 182 1240 562 5.37 136 230 4.13 Yellow 63/4 171 113/8 289
183 1500 680 5.37 136 280 5.00 Gray 73/4 197 121/2 318
SLF- 184 1830 830 5.37 136 340 6.10 Pink 73/4 197 117/8 302 15‹/¢ 381 81/2 216 71/4 184 71/4 184 81/2 216 11/4 x 10 5/8x11/2
185 2230 1012 5.37 136 415 7.44 Silver 73/4 197 12‹/¢ 305 x 254 x 38
SLFH- 186 2710 1229 5.37 136 505 9.04 Tan 73/4 197 123/4 324
187 3300 1497 5.37 136 615 11.01 Blue/Orng 83/4 222 123/4 324 151/2 394 91/2 241 8 203 8 203 91/2 241
188 4100 1860 5.37 136 755 13.68 Blue/Red 83/4 222 133/8 340 16›/¢ 406 91/2 241 8 203 8 203 91/2 241
91/2 241 1 /2 x 10
1 3/4 x 2
189 4900 2223 5.37 136 915 16.35 Blue/White 91/8 232 131/2 343 16›/¢ 406 91/2 241 81/2 216 81/2 216
10 /2 267 x 254 x 51
190 6000 1852 5.37 136 1120 20.01 Blue/Yelo 91/2 241 145/8 371 17›/¢ 432 101/2 267 91/2 241 91/2 241 1
191 7300 2252 5.37 136 1365 24.35 Blue/Silvr 91/2 241 151/4 387 171/2 445 101/2 267 91/2 241 91/2 241 101/2 267
192 9000 2777 5.37 136 1670 30.01 Blue/Gray 101/4 260 155/8 397 18›/¢ 457 11›/¢ 279 10›/¢ 254 10›/¢ 254 11›/¢ 279 13/4 x 10 3/4 x 2
193 11000 3395 5.37 136 2040 36.69 Blue/Tan 101/4 260 16›/¢ 406 x 254 x 51
194 13300 6033 5.37 136 2482 44.36 Blue/Brown 11›/¢ 279 161/4 413 19›/¢ 483 12›/¢ 305 11›/¢ 279 11›/¢ 279 12›/¢ 305
195 16300 7394 5.37 136 3028 54.37 Blue/Pink 113/8 289 171/8 435 20›/¢ 508 12›/¢ 305 11›/¢ 279 11›/¢ 279 12›/¢ 305
196 19800 8981 5.37 136 3694 66.04 Blue/Black 115/8 295 18›/¢ 457 21›/¢ 533 13›/¢ 330 12›/¢ 305 12›/¢ 305 13›/¢ 330 2 x 10 1 x 21/2
197 24200 10977 5.37 136 4506 80.71 Blue/Green 13›/¢ 330 191/2 495 23›/¢ 584 14›/¢ 356 13›/¢ 330 13›/¢ 330 14›/¢ 356 x 254 x 64

198 29000 13154 5.27 136 5500 98.16 Blue/Purple 13›/¢ 330 191/8 486 23›/¢ 584 14›/¢ 356 13›/¢ 330 13›/¢ 330 14›/¢ 356

Mounts in gray area have steel holders top and bottom.
7
SLF SPRING MOUNTS MASON INDUSTRIES

Alternate bracket and spring adjustment methods to improve stability and

appearance when using 4” 102mm, 5” 127mm and greater deflection springs.

PULL-DOWN BRACKET 3 ADJUSTMENT BOLTS

SPRING CHARACTERISTICS
Spring Rated Ratio Ratio Spring Rated Ratio Ratio
Size Deflection Kx/Ky OD/OH Size Deflection Kx/Ky OD/OH
X 1.00-1.30 0.75-1.00 0.92-1.40 101-118 2.00-2.55 0.71-1.10 0.82-1.15
A 1.00-1.60 0.50-0.90 0.74-1.25 126-143 3.25 0.72-1.00 0.85-1.36
B 1.00-2.10 0.70-0.90 0.80-1.25 150-169 4.38 0.80-1.10 0.85-1.33
C & Multiples 1.00 0.90-1.10 0.92 174-198 5.27-5.38 0.70-1.00 0.92-1.31

PRODUCT FINISHES
All standard products have a painted or powder coated finish unless otherwise indicated.
Springs are powder coated or zinc electroplated.
All mounts can be manufactured in stainless steel or hot dipped galvanized at additional
cost.

MASON INDUSTRIES, INC.

350 Rabro Drive,Hauppauge, NY 11788 • 631/348-0282 • FAX 631/348-0279
2101 W. Crescent Ave., Suite D • Anaheim, CA 92801 • 714/535-2727 • FAX 714/535-5738
Email info@Mason-Ind.com • Website www.Mason-Ind.com
Wu1006
8 2/08