012-07124B

9/99
$1.00
Instruction Sheet
for the PASCO
Model ES-9078

BASIC ELECTROMETER

Introduction
When replacing batteries, do not touch any
The Model ES-9078 is a voltmeter used for direct of the components or wires in the integrated
measurements of voltage and indirect measurements circuit panel; the components and
of current and charge. Because of its high (“infinite”) wires are all static sensitive.
impedance of 1014 ohms, it is especially suited for
measuring charge in electrostatic experiments. It has a EQUIPMENT
sensitivity nearly 1000 times that of a standard gold-
Parts included:
leaf electroscope, a center-zero meter that directly
• Basic Electrometer (ES-9078)
indicates charge polarity, and measures charges as
• Associated Cables, four (4)
low as 10-11 coulombs.
Additional parts required:
With these features, you’ll find that your electrostatics
• Faraday Ice Pail (ES-9042A)
demonstrations and labs are easier to perform and,
• Proof Plane
with quantitative data, are more informative.
• Basic Variable Capacitor (ES-9079)
The electrometer is powered by four AA-alkaline • Pasco Computer Interface (Model 750, 500 or
batteries, easily replaced by opening the back casing 300)
of the electrometer.

© 1999 PASCO scientific

Basic Electrometer 012-07124B

Operation 2. Connect the test lead to the input connector of

The controls on the front panel of the the electrometer.
electrometer are explained in Figure 1. 3. Connect the ground post of the electrometer to
Whether you’re using the electrometer to an earth ground.
measure voltage, current, or charge, the
4. Push the power button ON. One of the range
following procedure should be followed each
switch LEDs will blink twice in quick
time you turn on the electrometer.
succession.
More information on making accurate 5. To zero the meter, press the ZERO button.
measurements is provided in the sections that You’re now ready to use the electrometer to
follow. measure charge, current or voltage.
Warning: 6. Set the range switch to the desired voltage range.
The range setting refers to the voltage input
1. Never use the electrometer for
required to produce a full-scale meter deflection
measuring potentials more than 100 volts.
(e.g., a setting of 30 means that a full scale meter
2. Never connect the electrometer to an deflection indicates a voltage of 30 volts).
electrostatics generator, such as a Van de
Graff generator or a Wimhurst machine. Important Points for General
Operations:
3. Avoid touching the input leads until you
have grounded yourself to an earth ground. 1. Between measurements, always press the
A person walking across a rug on a cool Zero button to discharge all excess charge from
dry day can easily acquire a potential of the electrometer. Shorting the test leads together
several thousand volts. is insufficient. There may still be stray charges
within the electrometer circuitry. Note that on
meter
display the most sensitive scale (3 volts), the meter may
mechanical zero not return to exactly zero when the Zero button
zero button, adjust screw
ground and (adjust with
is pressed. This is normal and will not affect the
remove excess power off) accuracy of the reading.
charges

2. DO NOT use the mechanical zero adjust screw

select voltage
range connect test to set the meter to zero, unless power is off.
(3,10,30,100V) lead here
3. For good results, it is essential that the
connect to electrometer be connected to an earth ground (a
output signal
to interface earth ground water pipe or the ground wire from a 120 VAC
100 V
socket). Only an earth ground provides a
sufficient drain for excess charges that may
push to turn ON/OFF
build up during an experiment. It is also helpful
Figure 1. Electrometer panel controls if the experimenter is grounded. Just touch one
Setup Procedure hand to a good earth ground just before, or
during measurements.
1. Before turning on the electrometer, check that
the meter reads zero. If not, turn the Mechanical
Zero Adjust screw, located just below the meter
face, until it does.

!
012-07124B Basic Electrometer

Measuring Voltage the electrometer reading will generally remain

The electrometer can be thought of as an relatively unchanged. This is because the total
infinite impedance voltmeter. To show that the capacitance is only negligibly affected by the proof
electrometer is like a voltmeter, connect the plane. This may not always be the case, however.
leads to the battery, set the range (3, 10, 20, or
100 volts full scale), and read the voltage on the Any charge measurement with the electrometer is
meter. indirect, based on the knowledge that the amount
of charge on an object is proportional to the
Measuring Charge potential difference. The readings of the
Induction Charges electrometer will always be of volts, not of
Under most conditions, the best way to measure coulombs. The polarity of the voltage, however,
charge is by induction. Use a proof plane and a directly shows the type of charge being sampled. If
Faraday ice pail, such as those included with you need quantitative rather than qualitative charge
PASCO’s Demonstration Electrostatics System, and measurement, values for the charge can be
shown in Figure 2. The proof plane is simply a computed according to the relationship Q = CV,
small conductive disk mounted on an insulating where V is the voltage across a known capacitor of
handle. To sample the charge distribution on a capacitance C .
charged object, simply touch it with the proof The electrometer can be thought of as an infinite
plane, then place the proof plane inside the inner impedance voltmeter in parallel with a capacitor, CE ,
cylinder of the ice pail, without touching the as shown in Figure 3. CE represents the internal
cylinder. A charge of equal magnitude and sign is capacitance of the electrometer, plus the capacitance
induced on the surface of the ice pail and can be of the leads and the capacitance of the Ice Pail, if
read by the electrometer. By always using the being used.
proof plane and the ice pail, the capacitance will be
the same for all your measurements, and the charge
on the proof plane will always be proportional to the
!" Electrometer
voltage reading of the electrometer. !"#$%&$&'

shield ice pail

proof
black plane
clip
electrometer Figure 3. Ideal Schematic of the Electrometer

red When a charged object is placed across the

clip
electrometer leads (or in the ice pail), a voltage V
displays on the meter. If the value CE is known, the
value of the charge can be calculated as Q = C EV.
insulator The capacitance of the electrometer alone is around
27 pF. However, if the sampled object adds
significant capacitance, the situation becomes as
Figure 2. Using a Faraday Ice Pail shown in Figure 4.

Contact Charges
Charges can also be measured by contact. If you
touch the inner cylinder of the ice pail with a
charged object, for example a charged proof plane,
"
Basic Electrometer 012-07124B

connected across the leads of the electrometer, it is

connected in parallel with the internal capacitance
!" !#$% of the electrometer, CE. The total capacitance
!"#$%&$&' Capacitance of
object con- becomes C + CE. The known capacitor discharges
nected to the across the electrometer and a voltage, VE, is read.
Electrometer
Since the total charge in the system is still just the
Electrometer
charge of the known capacitor, we know that
Figure 4. Change in capacitance due to a charged object
CV = C + CE VE .

To accurately calculate the amount of charge, total 1. Obtain a low leakage capacitor (polypropylene,
capacitance CE + Cext must be determined. In any or air dielectric) of known value C, around 30
case, for quantitative measurements of charge, you pF.
need to have an accurate value for CE (Cext >>CE) ,
2. Charge the capacitor with a known voltage V,
unless you are certain that the object you are
measuring has a high enough capacitance to
disregard CE. The capacitors in the PASCO RC C V – VE
CE =
Network (ES-9053), for example, are high enough VE
that CE need not be considered. This is not true,
not higher than 100V (the limit of the
however, when using the parallel plate variable
capacitor (ES-9079). electrometer).
3. Remove the charged capacitor from the power
The following process shows you how to measure an supply used to charge it, being careful not to
experimental value of the capacitance of the ground it in any way, so as not to remove the
electrometer, any cables connected to it, and the ice charge.
pail.
4. Connect the charged capacitor across the
Measuring the Capacitance of the Electrometer electrometer input leads. (Or across the pail and
and Connectors shield of the ice pail, if you want to include its
For all experiments, the electrometer can be thought of capacitance value). Note the voltage VE
as a voltmeter connected in parallel with a indicated by the electrometer.
capacitor, as shown in Figure 2. The capacitor CE 5. Calculate the total capacitance:
represents the internal capacitance of the
electrometer, plus the capacitance of the leads and Measuring Current
the ice pail. The electrometer can be used for indirect current
measurements.
Use this procedure to measure a precise value of
the capacitance provided by the electrometer and Connect the electrometer leads across a known
all instruments connected to it. If you are interested resistance in the circuit and measure the voltage.
in qualitative, rather than quantitative experiments, Use Ohm’s Law V = IR to determine the current.
this procedure is not necessary. Due to the electrometer’s exceedingly high input
impedance, the effect of the electrometer in the
When a known capacitor C, is charged by a
circuit will be negligible in most circuits. However,
known voltage V, the charge in it is given by
the voltage drop across the resistor must be within
Q = CV. If the known charged capacitor is
the voltage range of the electrometer (100 V
maximum).

#
012-07124B Basic Electrometer

If it is not convenient to hook the electrometer Specifications

across a known resistance in the circuit, a precision
ES-9078 Basic Electrometer:
resistor can be connected between the input leads
of the electrometer. The circuit can be broken, as Voltage input ranges: 3, 10, 30, 100 volts full scale
for connection to a standard ammeter, and
Input resistance: approximately 10^14 ohms
connected in series with the precision resistor.
Again, measure the voltage across this resistor and Input capacitance: approximately 27 pF
calculate the current. (The problem with this Accuracy: Analog Meter: +/ 3% -
technique is that the resistance must be high ScienceWorkshop output: +/ - 1%
enough to measure a voltage drop, but low enough Signal output: Fixed at -100 to + 100 volt range
so it doesn’t significantly affect the current through (Automatically scaled in DataStudio
and ScienceWorkshop)
the circuit).
Batteries: 4 - “AA” (Alkaline recommended)
Using a Computer with Science Workshop Battery life: approximately 75 hours
Interface
The signal output connector on the ES-9078 Note: This instruction sheet assumes the
Electrometer provides an output signal for the Science user is familiar with ScienceWorkshop® or
Workshop interface. This provides an output DataStudio™. Users can gain familiarity by
signal for displaying data in analog meters, tables, working through the tutorials provided in
graphs or oscilloscopes, making data analysis easy. ScienceWorkshop or DataStudio’s Online
Help.
It is important to remember that the signal output on
the ES-9078 has a fixed scale of ±100 volts. Changing
The exclamation point within an equilateral
the range switch on the electrometer has no effect on triangle is intended to alert the user of
this scaling. By choosing the Electrometer icon in important operating and safety instructions
DataStudio™ or ScienceWorkshop®, displays are that will help prevent damage to the
equipment or injury to the user.
shown correctly scaled.

Because of limited resolution on this output, it may be

useful to apply gain within the ScienceWorkshop
interface to measure voltages of 10 volts or less.

$
Basic Electrometer 012-07124B

Technical Support
Feedback Contacting Technical Support
If you have any comments about the product or Before you call the PASCO Technical Support
manual, please let us know. If you have any staff, it would be helpful to prepare the following
suggestions on alternate experiments or find a information:
problem in the manual, please tell us. PASCO
appreciates any customer feedback. Your input helps ➤ If your problem is with the PASCO apparatus,
us evaluate and improve our product. note:
! Title and model number (usually listed on the
To Reach PASCO label);

For technical support, call us at 1-800-772-8700 ! Approximate age of apparatus;

(toll-free within the U.S.) or (916) 786-3800. ! A detailed description of the problem/sequence
of events (in case you can’t call PASCO right
fax: (916) 786-3292 away, you won’t lose valuable data);
e-mail: techsupp@pasco.com ! If possible, have the apparatus within reach
when calling to facilitate description of
web: www.pasco.com individual parts.
➤ If your problem relates to the instruction
manual, note:
! Part number and revision (listed by month and
year on the front cover);
! Have the manual at hand to discuss your
questions.

Warranty
Limited Warranty postage or freight prepaid. (Damage caused by
PASCO scientific warrants the product to be free from improper packing of the equipment for return shipment
defects in materials and workmanship for a period of will not be covered by the warranty.) Shipping costs for
one year from the date of shipment to the customer. returning the equipment after repair will be paid by
PASCO will repair or replace, at its option, any part of PASCO scientific.
the product which is deemed to be defective in material
Address: PASCO scientific
or workmanship. The warranty does not cover damage
10101 Foothills Blvd.
to the product caused by abuse or improper use.
Roseville, CA 95747-7100
Determination of whether a product failure is the result
of a manufacturing defect or improper use by the
Phone: (916) 786-3800
customer shall be made solely by PASCO scientific.
FAX: (916) 786-8905
Responsibility for the return of equipment for warranty
e-mail: techsupp@pasco.com
repair belongs to the customer. Equipment must be
Web site: www.pasco.com
properly packed to prevent damage and shipped