SITE PREPARATION STEEL WORK

1. DO NOT USE COMPACTION METHODS THAT WILL CAUSE DAMAGE TO ADJACENT 1. ALL STEELWORK TO COMPLY WITH AS 4100
STRUCTURES. SELECTION OF METHODS SHALL BE BUILDERS RESPONSIBILITY. 2. HOT ROLLED STEEL TO CONFORM WITH AS 3678. MIN. GRADE 550 (550 MPa MIN.
2. ENSURE THAT THE SOIL STRATA BELOW PAD FOOTINGS FOR A DEPTH OF AT LEAST YIELD STRESS).
750mm IS COMPACTED SAND WITHOUT ROOT, ROCK, ETC. 3. HOT ROLLED FLATS, BRACKETS, TFC, TFB, ANGLES 100x100 EA OR 125x75 UA &
SMALLER COMPLYING WITH AS 3679.1. MIN. GRADE 450
3. SAND PAD SHALL BE CLEAN, WELL GRADED YELLOW SAND AND COMPACTED.
4. ALL WELDING TO COMPLY WITH AS 1554 PARTS 1 AND 2.
4. FOOTINGS SHALL BE LOCATED CENTRALLY BENEATH WALLS AND COLUMNS UNLESS 5. ALL WELDS TO DEVELOP FULL STRENGTH OF MEMBERS JOINED. U.N.O.
NOTED OTHERWISE. 6. FULLY SEAL ALL HOLLOW SECTIONS USING 5MM PLATES WHERE NECESSARY.
5. THE BOTTOM OF ALL FOOTING EXCAVATIONS SHALL BE CLEANED OUT, COMPACTED AND 7. PROVIDE ALL CLEATS, BRACKETS, HOLES, ETC. NOT SHOWN BUT NECESSARY TO
TESTED PRIOR TO PLACING REINFORCEMENT. COMPLETE THE BUILDING.
6. IF APPLICABLE, ADEQUATELY DEWATER CUT BASE OR FOUNDATIONS TO ACHIEVE AND 8. UNLESS OTHERWISE SHOWN, ALL BOLTED CONNECTIONS ARE TO DEVELOP FULL
MAINTAIN COMPACTION. STRENGTH OF MEMBERS JOINED.
7. SAND UNDER FOOTINGS AND SLABS ON GROUND SHALL BE COMPACTED IN 9. STEEL BEAMS TO BE FABRICATED WITH NATURAL CAMBER UP.
UNDISTURBED IN SITU SAND AND FOR THE FULL DEPTH OF ALL FILLING SAND TO GIVE A 10. UNLESS OTHERWISE NOTED, USE:
PENETRATION RESISTANCE OF 8 BLOWS MIN PER 300MM USING A STANDARD FALLING (a) 10MM THICK GUSSET FIN AND END PLATES AND 2-M16 8.8/S BOLTS.
WEIGHT PENETROMETER OR (b) 6MM CONTINUOUS GP FILLET WELD.
11. ALL BOLTED CONNECTIONS TO BE BOLTING CATEGORY 8.8/S U.N.O.
12. PROVIDE TEMPORARY BRACING DURING ERECTION.
13. USE 1:2 CEMENT: SAND GROUT UNDER ALL SEATING AND BASE PLATES, ENSURING THE
SPACE UNDER THE PLATES IS COMPLETELY FILLED.
CONCRETE/REINFORCEMENT 13. WHERE MASONRY WALLS ABUT OR ADJACENT TO STEEL COLUMNS: WELD A VERTICAL
1. FOOTING CONCRETE TO BE OF 32 MPA GRADE; REINFO. COVER OF 70 (BOTTOM). R10 ROD TO COLUMN. LENGTH OF WELD TO BE 25mm EACH SIDE OF ROD EVERY 350mm.
PROVIDE 5MM CLEARANCE BETWEEN ROD AND COLUMN FACE.
2. GROUND SLAB CONCRETE TO BE OF 32MPA GRADE; REINFO. COVER OF 30 (TOP) DESIGN CRITERIA
14. ALL INTERNAL STEELWORK TO BE RUSTPROOFED USING A RED OXIDE ZINC PHOSPHATE
3. CONCRETE TO CONFORM WITH AS3600. PRIMER ON CLEANED SURFACES U.N.O.
4. LAP ALL MESH AT LEAST ONE TRANSVERSE WIRE PLUS 25MM OR TO MANUFACTURER'S 15. EXTERNAL STEELWORK TREATMENT TO CONFORM WITH AS/NZS 2312
BUILDING IMPORTANCE LEVEL (B.C.A.) LEVEL 2
SPECIFICATION UNLESS OTHERWISE NOTED. 16. COLD FORMED SECTIONS TO CONFORM TO AS 1397 - GRADE 450 (450 MPa MIN. YIELD WIND LOADING CRITERIA (AS / NZS1170.2)
5. BLENDED CEMENT TO CONFORM WITH AS3972. STRESS).
17. PROVIDE EXTRA PURLINS & GIRTS AS REQUIRED TO SUIT PENETRATIONS AND GUTTERS.
- REGION A
6. ALL CONCRETE IS OF 20 MAX AGG AND 80 SLUMP.
18. ALL STEELWORK IN CONTACT WITH THE GROUND IS TO BE COATED WITH 2 COATS OF A - TERRAIN CATEGORY 2.0
7. CONCRETE IS TO BE COMPACTED USING MECHANICAL VIBRATORS.
COAL TAR EPOXY TO A MINIMUM TOTAL THICKNESS OF 0.4mm. - WIND CLASSIFICATION (IN ACCORDANCE WITH AS 4055) N1
8. SIZES OF CONCRETE ELEMENTS DO NOT INCLUDE THICKNESS OF APPLIED FINISHES.
19. STEELWORK ARE TO BE TOTAL SPAN, SPANBUILD, STRAMIT, OR OTHER SECTIONS
9. NO HOLES, CHASES OR EMBEDDED PIPES, OTHER THAN THOSE SHOWN ON THE APPROVED IN WRITING BY THE ENGINEER, COMPLYING WITH AS 1397, AND A MINIMUM - WIND TOPOGRAPHY T0
STRUCTURAL ENGINEER'S DRAWINGS, SHALL BE MADE WITHOUT THE APPROVAL OF THE GALVANIZED COATING OF Z450 (450G/SQM). CLEAT CONNECTIONS ARE TO BE IN
ENGINEER.
- WIND SHIELDING PS
ACCORDANCE WITH AISC STANDARDISED CONNECTIONS OR MANUFACTURER'S
10. CONCRETE SHALL BE CONTINUOUSLY WATER CURED FOR 3 DAYS AFTER POURING AND RECOMMENDATIONS U.N.O. BOLTING AND BRIDGING TO BE IN ACCORDANCE WITH
KEPT DAMP FOR NOT LESS THAN A FURTHER 4 DAYS THEREAFTER. MANUFACTURER'S RECOMMENDATIONS. PURLIN/GIRT SPACING IS NOT TO EXCEED THE CORROSION CLASSIFICATION R3
11. FORMWORK AND ITS REMOVAL TO BE IN ACCORDANCE WITH AS.3610. CLADDING MANUFACTURERS SPAN SPECIFICATIONS.
SOIL CLASSIFICATION (AS PER AS2870) ASSUMED 'M'
12. DO NOT USE ADMIXTURES TO CONCRETE UNLESS SPECIFIED OR PRIOR APPROVED BY THE
ENGINEER.
13. CONSTRUCTION TOLERANCES TO BE IN ACCORDANCE WITH AS 3600 CL. 17.5. SOIL BEARING CAPACITY 100 kPa
ROOF AND WALL PANELS
14. SURFACE FINISHES TO BE IN ACCORDANCE WITH AS.3610.
1. METAL ROOF AND WALL SHEET TO BE INSTALLED IN ACCORDANCE WITH THE MANUFACTURERS
15. CURING OF CONCRETE SHALL BE COMMENCED AS SOON AS POSSIBLE AFTER PLACING OR DETAILS AND SPECIFICATION FOR THE SPECIFIED WIND REGION.
STRIPPING. REFER TO CLAUSE 19.1.5 AS.3600.
16. REINFORCEMENT SHALL COMPLY TO AS1302, A1303, AS1304 AS APPROPRIATE. LAPS
SHALL BE IN ACCORDANCE WITH AS3600. DISCLAIMER DESIGN ONLY SUITS WELL DRAINED SITES
17. REINFORCEMENT SYMBOLS:- 1. THESE DRAWINGS SHALL BE READ IN CONJUNCTION WITH THE MANUFACTURER'S
N NORMAL DUCTILITY GRADE 500N DEFORMED BARS TO AS 4671 SPECIFICATIONS. ANY DISCREPANCIES MUST BE REPORTED TO THE ENGINEER PRIOR TO
R GRADE 230R HOT ROLLED PLAIN BARS TO AS 4671 COMMENCEMENT. * FOOTING STRUCTURE ARE NOT DESIGNED FOR AREA WITH HIGH WATER TABLE. IF
SL HARD DRAWN REINFORCING FABRIC TO AS 4671
W HARD DRAWN PLAIN WIRE TO AS 4671
2. MEMBERS OR CONNECTIONS NOT NOTED IN THESE DRAWINGS ARE TO BE ENGINEERED BY WATER TABLE IS FOUND TO BE HIGH IN THE SUBJECT AREA, CONSTRUCTION MUST NOT
OTHERS.
18. THE CONTRACTOR SHALL SUPPLY ALL NECESSARY BAR CHAIRS, SUPPORT AND SPACER 3. DO NOT OBTAIN DIMENSIONS BY SCALING FROM THE DRAWINGS. ALL DIMENSIONS ARE COMMENCE AND A FULL SITE GEOTECHNICAL INVESTIGATION MUST BE CONDUCTED AND
BARS TO LOCATE REINFORCING STEEL IN ITS CORRECT LOCATION DURING CONCRETE
PLACEMENT.
IN MILLIMETRES UNO AND ALL LEVELS IN METRES. THE STRUCTURAL ENGINEER MUST BE NOTIFIED IMMEDIATELY
4. ROOF IS NOT TO CARRY ANY ADDITIONAL LOAD SUCH AS WATER TANK OR HOT WATER
19. ALL CAST IN FITTINGS SHALL BE HOT DIP GALVANISED OR STAINLESS STEEL.
SYSTEM. CONSULT ENGINEER IF REQUIRED.
20. PROVIDE ALL EXPOSED EDGES AND CORNERS WITH 20 CHAMFERS OR FILLETS.
5. FLOOR ADDITIONAL LOADING (IMPOSED LOAD) IS TO BE LESS THAN 1.5KN/M2. CONSULT
REINFORCEMENT SHALL BE SPLICED WHERE SHOWN ON THE DRAWINGS. WHERE NOT
DETAILED, SPLICES TO ALL REINFORCEMENT INCLUDING DISTRIBUTION BARS SHALL BE ENGINEER IF REQUIRED.
STAGGERED WITH MINIMUM OVERLAP OF 40 BAR DIAMETERS. 6. THESE DRAWINGS ARE SOLELY FOR THE INTENDED RECIPIENT AND FOR THE PURPOSES
21. U.N.O THE CORNERS OF ALL OPENINGS AND RE-ENTRANT CORNERS SHALL BE STATED.
REINFORCED WITH 2-N16 BARS AT 100 CRS, 2000 LONG-TOP. 7. BUILDER TO ADVISE CLIENT NOT TO PLANT TREES OR SHRUBS WITHIN 2.5M OR A
22. TEMPLATES SHALL BE USED TO CORRECTLY LOCATE AND HOLD IN POSITION HOLDING DISTANCE EQUAL TO THE ANTICIPATED MAXIMUM HEIGHT OF THE TREES TO THE PROJECT:
DOWN BOLTS DURING PLACEMENT OF CONCRETE. BUILDING. (WHICHEVER IS LEAST).
8. BUILDER TO INFORM THE CLIENT OF NECESSITY TO MAINTAIN DRAINS IN GOOD WORKING PROPOSED SHEDS ON LOT 264,
ORDER. #9 COX STREET, PINJARRA WA
9. BUILDER TO DRAIN ROOF AND SURFACE WATER AWAY FROM FOUNDATION AREA DURING
AND AFTER CONSTRUCTION. DATE : 12/07/2022

DRAWING TITLE: GENERAL NOTES

NOTE: FOOTINGS HAVE BEEN DESIGNED BASED ON THE ASSUMPTION OF
CLASS "M" SITE CLASSIFICATION IN ACCORDANCE WITH "AS 2870"
AND 100 KPA SOIL BEARING CAPACITY. IT IS HIGHLY RECOMMENDED
THAT A SITE CLASSIFICATION IS CARRIED OUT BY A GEOTECHNICAL
ENGINEER AND THIS ASSUMPTION IS VERIFIED. OWNER TO NOTIFY
ENGINEER IF SITE CLASSIFICATION IS DIFFERENT TO CLASS "M"

IMPORTANT:
OWNER TO VERIFY AND CONFIRMED SITE WIND RATING IS 'N1' AND SOIL
CLASSIFICATION IS 'M' PRIOR TO THE COMMENCEMENT OF ANY
CONSTRUCTION WORK. THIS CERTIFICATION TOGETHER WITH ALL RELATED
DRAWINGS SET ARE VOIDED IF WIND RATING IS NOT 'N1' AND SITE
CLASSIFICATION IS NOT 'M'
SHEET S-01
 10000 48000 2300

60.3m

200
2no. 1200Ø x 1500mm
2no. 1200Ø x 1500mm
DEEP SOAKWELLS
DEEP SOAKWELLS

SHED 1

11000
48m x 11m
(528m²)
35.2m

3100L
POINT OINT OINT OINT
SEPTIC
P P P
DRAIN DRAIN DRAIN DRAIN TANK
COX STREET

POINT
LOT 264 (#9) DRAIN

35.2m
2124.6m²

EXISTING
BUILDING

SHED 2
12000

15m x 12m
(180m²)
1000

60.3m
10000 15000

*THIS DRAWING IS STRICTLY TO BE USED ONLY FOR COUNCIL APPROVAL APPLICATION

DATE PROJECT DRAWING TITLE DWG NO. NOTES

1. All architectural dimensions are in millimeters unless notified otherwise.

12/07/2022

N
PROPOSED SHEDS ON LOT 264, #9 SITE PLAN 2. All dimensions are to be checked on site.
SHEET SIZE COX STREET, PINJARRA WA

SCALE 1 : 200 A3
A001 3. Drawing is strictly to be used for council application purpose only and does not form part of construction working
drawings. Property owner holds / bears the full responsibilities & liabilities for supervision & coordination to all construction
works & details after receiving building permit approval from local council.
 F9 F8 F7 F6 F5 F4 F3 F2 F1

48000

6000 6000 6000 6000 6000 6000 6000 6000

8 7 6 5 4 3 2 1
11000

6.0m 6.0m 6.0m 6.0m 6.0m 6.0m 6.0m 6.0m

wc wc wc wc
1500

1500

1500
A 1000 1250 1250 1000

4897 911 12384 911 9794 911 11089 911 6192

7400 3200 2800 3200 14800 3200 8800 3200 1400

B
PLAN VIEW F9 F1
A
A B B A

RIDGE RIDGE

BOUNDARY

BOUNDARY
STEEL WORK NOTES:
ALL STEEL WORK TO COMPLY WITH NASH STANDARDS AND AUSTRALIAN STANDARDS: AL L 15° F AL L 15° F
15° F ALL 15° F ALL
- AS 4100, AS 4600, AS 3623, AS 1554, AS 3678, AS 3679 AND/OR AS 1163.

ALL STEEL COMPONENTS TO BE FULLY GALVANISED EAVE EAVE

ALL CONSTRUCTION WITHIN 1.5KM OF THE COAST OR 100M OF THE RIVER IS TO HAVE
MARINE GRADE ROOF SHEETING, FLASHING, FIXINGS AND STEEL FINISH TO MEET THE
6274

6274
MANUFACTURER'S RECOMMENDATIONS FOR MARINE EXPOSURE
0.4BMT 6-RIB WALL CLADDING FITTED IN ACCORDANCE 0.4BMT 6-RIB WALL CLADDING FITTED IN ACCORDANCE
REFER TO SHEET S-01 FOR FULL STEEL WORK NOTES
4800

4800
TO MANUFACTURER'S SPECIFICATION TO MANUFACTURER'S SPECIFICATION

WET AREA WALLS @ 2400mm HIGH

* IMPORTANT: NO CEILING OR INTERNAL WALL LINING SHOULD BE ADDED TO THE SHED STRUCTURE
OTHER THAT WET AREA AND FIRE WALL ALONG BOUNDARY

F1 ELEVATION F9 ELEVATION
* ALL CAPPINGS, GUTTER, DOWNPIPE, DRIP RAILS, FLASHING, POP-INS & CLIPS FITTED TO BUILDER'S DETAIL

NOTES:
1. ALL WORK TO BE COMPLETED IN ACCORDANCE TO NATIONAL CONSTRUCTION CODE (NCC) AND AUSTRALIAN STANDARDS BY A FULLY
LICENCED / REGISTERED BUILDER.
2. IT IS THE BUILDER'S RESPONSIBILITY TO COMPLY WITH ALL STATUTORY AUTHORITY REGULATIONS AND REQUIREMENTS WHICH IN THE EVENT
OF ANY DISCREPANCY SHALL TAKE PRECEDENCE OVER THESE DRAWINGS
3. BUILDER MUST CONFIRM ON SITE ALL DIMENSIONS IN ACCORDANCE WITH THESE PLANS . DO NOT SCALE FROM DRAWINGS.
4. ENSURE NO EXISTING STRUCTURES OR SERVICES ON THIS OR ADJACENT PROPERTIES WILL BE SURCHARGED OR UNDERMINED BY THESE
WORKS. IF UNSURE, CONTACT THE STRUCTURAL ENGINEER FOR PROPER ADVICE PRIOR TO PROCEEDING.
5. DOWNPIPES TYPE, SIZE AND LOCATION TO BE DETERMINED ON SITE BY BUILDER.
6. ANY DISCREPANCIES TO BE NOTIFED TO THE OWNER OR STRUCTURAL ENGINEER PRIOR TO WORK COMMENCING.
7. DRAINAGE REQUIREMENTS (SUBSOIL, SOAKWELLS, RUNOFF AND STORMWATER) ARE TO BE DETERMINED ON SITE. ENSURE THERE IS NO
DISCHARGE OR POOLING OF WATER AGAINST THE SLAB AND / OR FOOTINGS. *THIS DRAWING IS STRICTLY TO BE USED ONLY FOR COUNCIL APPROVAL APPLICATION

DATE PROJECT DRAWING TITLE DWG NO. NOTES

1. All architectural dimensions are in millimeters unless notified otherwise.

12/07/2022

N
PROPOSED SHEDS ON LOT 264, #9 SHED 1 LAYOUT PLAN - 01 2. All dimensions are to be checked on site.
SHEET SIZE COX STREET, PINJARRA WA

SCALE 1 : 150 A3
A002 3. Drawing is strictly to be used for council application purpose only and does not form part of construction working
drawings. Property owner holds / bears the full responsibilities & liabilities for supervision & coordination to all construction
works & details after receiving building permit approval from local council.
 F9 F8 F7 F6 F5 F4 F3 F2 F1

RIDGE

0.4BMT 6-RIB ROOF SHEET @15° FALL. FITTED IN

ACCORDANCE TO MANUFACTURER'S SPECIFICATION
EAVE
6274

0.4BMT 6-RIB WALL CLADDING FITTED IN ACCORDANCE

TO MANUFACTURER'S SPECIFICATION
4800

3200

3200
ROLLER DOOR ROLLER DOOR ROLLER DOOR ROLLER DOOR

1940

1940

1940
A ELEVATION

F1 F2 F3 F4 F5 F6 F7 F8 F9

RIDGE

0.4BMT 6-RIB ROOF SHEET @15° FALL. FITTED IN

ACCORDANCE TO MANUFACTURER'S SPECIFICATION
EAVE
SQUARELINE GUTTER
6274

FIRECRUNCH FCA K-CLAD WALL CLADDING

4800

SYSTEM FITTED IN ACCORDANCE TO

MANUFACTURER'S SPECIFICATION

B ELEVATION
STEEL WORK NOTES: 13mm GYPROCK FYRCHEK MIN. 300mm HIGH TILED
ALL STEEL WORK TO COMPLY WITH NASH STANDARDS AND AUSTRALIAN STANDARDS: PLASTERBOARD INTERNAL WALL LINING UPTURN TO WET AREA WALLS
- AS 4100, AS 4600, AS 3623, AS 1554, AS 3678, AS 3679 AND/OR AS 1163.
C90 x 1.15BMT STEEL STUD WALL VILLABOARD OR GYPROCK AQUACHEK
ALL STEEL COMPONENTS TO BE FULLY GALVANISED MOISTURE RESISTANT PLASTERBOARD
SPACED @ 600 C/C TO "NASH"
STANDARD. MAX HEIGHT = 2400mm WALL LINING TO WET AREAS
ALL CONSTRUCTION WITHIN 1.5KM OF THE COAST OR 100M OF THE RIVER IS TO HAVE
MARINE GRADE ROOF SHEETING, FLASHING, FIXINGS AND STEEL FINISH TO MEET THE WATER PROOFING MEMBRANE
BOTTOM STUD DYNABOLTED INTO
MANUFACTURER'S RECOMMENDATIONS FOR MARINE EXPOSURE
CONCRETE BASE VIA M12 BOLT @
WET AREA SETDOWN WATERPROOF SCREED LAID TO FALL
EVERY 900 C/C INTERVALS
REFER TO SHEET S-01 FOR FULL STEEL WORK NOTES 40mm WET AREA SETDOWN. MAINTAIN 100mm SLAB THICKNESS.
FOLD MESH DOWN TO MAINTAIN COVER. PLACE DIAGONAL BARS AT ANTI SLIPPERY FLOOR TILES
RE-ENTRANT CORNERS FOR STEPS OVER 30mm. SL92 MESH WITH WATERPROOF MORTAR
WET AREA WALLS @ 2400mm HIGH FALL

30

40
30
* IMPORTANT: NO CEILING OR INTERNAL WALL LINING SHOULD BE ADDED TO THE SHED STRUCTURE

125
165
OTHER THAT WET AREA AND FIRE WALL ALONG BOUNDARY

125
40
* ALL CAPPINGS, GUTTER, DOWNPIPE, DRIP RAILS, FLASHING, POP-INS & CLIPS FITTED TO BUILDER'S DETAIL
'S1' GROUND SLAB

NOTES: 'IT1' INTERNAL THICKENING

1. ALL WORK TO BE COMPLETED IN ACCORDANCE TO NATIONAL CONSTRUCTION CODE (NCC) AND AUSTRALIAN STANDARDS BY A FULLY 300
0.2mm POLYTHENE MEMBRANE
LICENCED / REGISTERED BUILDER. ON TERMITE TREATED (to
2. IT IS THE BUILDER'S RESPONSIBILITY TO COMPLY WITH ALL STATUTORY AUTHORITY REGULATIONS AND REQUIREMENTS WHICH IN THE EVENT AS3660.1) COMPACTED SAND
OF ANY DISCREPANCY SHALL TAKE PRECEDENCE OVER THESE DRAWINGS
3. BUILDER MUST CONFIRM ON SITE ALL DIMENSIONS IN ACCORDANCE WITH THESE PLANS . DO NOT SCALE FROM DRAWINGS.
4. ENSURE NO EXISTING STRUCTURES OR SERVICES ON THIS OR ADJACENT PROPERTIES WILL BE SURCHARGED OR UNDERMINED BY THESE
WET AREA SETDOWN - TYPICAL
WORKS. IF UNSURE, CONTACT THE STRUCTURAL ENGINEER FOR PROPER ADVICE PRIOR TO PROCEEDING.
5. DOWNPIPES TYPE, SIZE AND LOCATION TO BE DETERMINED ON SITE BY BUILDER. 2 1 : 10
6. ANY DISCREPANCIES TO BE NOTIFED TO THE OWNER OR STRUCTURAL ENGINEER PRIOR TO WORK COMMENCING.
7. DRAINAGE REQUIREMENTS (SUBSOIL, SOAKWELLS, RUNOFF AND STORMWATER) ARE TO BE DETERMINED ON SITE. ENSURE THERE IS NO
DISCHARGE OR POOLING OF WATER AGAINST THE SLAB AND / OR FOOTINGS. *THIS DRAWING IS STRICTLY TO BE USED ONLY FOR COUNCIL APPROVAL APPLICATION

DATE PROJECT DRAWING TITLE DWG NO. NOTES

1. All architectural dimensions are in millimeters unless notified otherwise.

12/07/2022
PROPOSED SHEDS ON LOT 264, #9 SHED 1 LAYOUT PLAN - 02 2. All dimensions are to be checked on site.
SHEET SIZE COX STREET, PINJARRA WA

SCALE As indicated A3
A003 3. Drawing is strictly to be used for council application purpose only and does not form part of construction working
drawings. Property owner holds / bears the full responsibilities & liabilities for supervision & coordination to all construction
works & details after receiving building permit approval from local council.
 F9 F8 F7 F6 F5 F4 F3 F2 F1

f e e e e e e e f
B k j j j j j j k
CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB
T T
F i F F c F F c F F c F F c F F c F F c F F i F
m m m m m m m m m m m m m m m m
T Q Q Q Q Q Q Q Q Q Q Q Q Q Q Q Q T
i c c c c c c i
T T
F i F F c F F c F F c F F c F F c F F c F F i F
m m m m m m m m m m m m m m m m
T Q Q Q Q Q Q Q Q Q Q Q Q Q Q Q Q T
i c c c c c c i
T T
F i F F c F F c F F c F F c F F c F F c F F i F
m g m m d
g m m d
g m m d
g m m d
g m m d
g m m d
g m m g m
PN L Q Q T PR Q Q T PR Q Q T PR Q Q T PR Q Q T PR Q Q T PR Q Q T PR Q Q T PN
PN T
mQ g Q
m T PR
mQ d
g Q
m T PR
mQ d
g Q
m T PR
mQ d
g Q
m T PR
mQ d
g Q
m T PR
mQ d
g Q
m T PR
mQ d
g Q
m T PR
mQ g Q
m L PN
F F F F F F F F F F F F F F F F
T h c
h c
h c
h c
h c
h c
h h T

h c
h c
h c
h c
h c
h c
h h
T
mQ Q
m mQ Q
m mQ Q
m mQ Q
m mQ Q
m mQ Q
m mQ Q
m mQ Q
m T
F F F F F F F F F F F F F F F F
T h c
h c
h c
h c
h c
h c
h h T

h c
h c
h c
h c
h c
h c
h h
T
mQ Q
m mQ Q
m mQ Q
m mQ Q
m mQ Q
m mQ Q
m mQ Q
m mQ Q
m T
F F F F F F F F F F F F F F F F
h h h c h h h h
T
l l l l l l l l
T B
CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB
A k j j j j j j k
f e e e e e e e f F9 F1

PLAN VIEW
A B B A

* NOTE: WET AREA STUDWORK NOT SHOWN ON THESE PLANS. REFER TO BUILDER'S DETAIL PN PN PN PN
UH UH
f f f f
1474

1474
PB W
ai N T ai W PB PB W
ai N T ai W PB
448

448
W F
ai F N T F
ai F W W F
ai F N T F
ai F W
EQ EQ EQ EQ

EQ EQ EQ EQ
al Q Q
al al Q Q
al al Q Q
al al Q Q
al
W
ai N T
ai W W
ai N T
ai W
4800

4800
4600

4600
4032

4032
STRUCTURAL STEEL MEMBERS: W N T W W N T W
F
ai F F
ai F F
ai F F
ai F
PROTECTIVE COATINGS FOR STRUCTURAL STEELWORK TO BE IN q al al q al al q q al al q al al q
Q Q Q Q Q Q Q Q
ACCORDANCE WITH NCC REQUIREMENTS AND AS 2312
W
ai N T
ai W W
ai N T
ai W
W N T W W N T W
STEEL WORK NOTES: ai ai ai ai
FC FC FC FC FC FC
120

120
ALL STEEL WORK TO COMPLY WITH NASH STANDARDS AND AUSTRALIAN STANDARDS:
- AS 4100, AS 4600, AS 3623, AS 1554, AS 3678, AS 3679 AND/OR AS 1163.

ALL STEEL COMPONENTS TO BE FULLY GALVANISED

F1 ELEVATION F9 ELEVATION
ALL CONSTRUCTION WITHIN 1.5KM OF THE COAST OR 100M OF THE RIVER IS TO HAVE
MARINE GRADE ROOF SHEETING, FLASHING, FIXINGS AND STEEL FINISH TO MEET THE
MANUFACTURER'S RECOMMENDATIONS FOR MARINE EXPOSURE

REFER TO SHEET S-01 FOR FULL STEEL WORK NOTES

* IMPORTANT: NO CEILING OR INTERNAL WALL LINING SHOULD BE ADDED TO THE SHED STRUCTURE
OTHER THAT WET AREA AND FIRE WALL ALONG BOUNDARY AND AS 4055

* ALL CAPPINGS, GUTTER, DOWNPIPE, DRIP RAILS, FLASHING, POP-INS & CLIPS FITTED TO BUILDER'S DETAIL
5.0m
NOTES:
1. ALL WORK TO BE COMPLETED IN ACCORDANCE TO NATIONAL CONSTRUCTION CODE (NCC) AND AUSTRALIAN STANDARDS BY A FULLY
LICENCED / REGISTERED BUILDER.
2. IT IS THE BUILDER'S RESPONSIBILITY TO COMPLY WITH ALL STATUTORY AUTHORITY REGULATIONS AND REQUIREMENTS WHICH IN THE EVENT TOTAL SPAN
OF ANY DISCREPANCY SHALL TAKE PRECEDENCE OVER THESE DRAWINGS
3. BUILDER MUST CONFIRM ON SITE ALL DIMENSIONS IN ACCORDANCE WITH THESE PLANS . DO NOT SCALE FROM DRAWINGS. ALL STEEL MEMBERS SHALL BE INSTALLED IN ACCORDANCE WITH
4. ENSURE NO EXISTING STRUCTURES OR SERVICES ON THIS OR ADJACENT PROPERTIES WILL BE SURCHARGED OR UNDERMINED BY THESE
WORKS. IF UNSURE, CONTACT THE STRUCTURAL ENGINEER FOR PROPER ADVICE PRIOR TO PROCEEDING. TOTAL SPAN SPECIFICATIONS
5. DOWNPIPES TYPE, SIZE AND LOCATION TO BE DETERMINED ON SITE BY BUILDER.
6. ANY DISCREPANCIES TO BE NOTIFED TO THE OWNER OR STRUCTURAL ENGINEER PRIOR TO WORK COMMENCING.
7. DRAINAGE REQUIREMENTS (SUBSOIL, SOAKWELLS, RUNOFF AND STORMWATER) ARE TO BE DETERMINED ON SITE. ENSURE THERE IS NO
DISCHARGE OR POOLING OF WATER AGAINST THE SLAB AND / OR FOOTINGS. *THIS DRAWING IS STRICTLY TO BE USED ONLY FOR COUNCIL APPROVAL APPLICATION

DATE PROJECT DRAWING TITLE DWG NO. NOTES

1. All architectural dimensions are in millimeters unless notified otherwise.

12/07/2022

N
PROPOSED SHEDS ON LOT 264, #9 SHED 1 STEEL LAYOUT PLAN 2. All dimensions are to be checked on site.
SHEET SIZE COX STREET, PINJARRA WA - 01

SCALE 1 : 150 A3
A004 3. Drawing is strictly to be used for council application purpose only and does not form part of construction working
drawings. Property owner holds / bears the full responsibilities & liabilities for supervision & coordination to all construction
works & details after receiving building permit approval from local council.
 F9 F8 F7 F6 F5 F4 F3 F2 F1

648 PB k PE j PE j PE j PE j PE j PE j PE k PB
CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB

F t F F s F s F s F F s F F s F s F F s T
EQ EQ EQ EQ ad ad ac ac ad ad ad ad ac ad ad ac
4800 EAVES

Q Q Q Q Q Q Q Q Q Q Q Q
t z W OG
ab OG W y z W OG
ab OG W y s s z W OG
ab OG W y s zW ab W y T
q r r r r r r r q
4032

OP
t zW y zW y s s zW y s zW y

OP

OP
aa aa aa aa

EN
F F W W F F F F W F F W T

EN

EN
OE OE OE OE
v v v v v v v v

IN
ad ad ad ad ad ad ad ad

IN

IN
ROLLER DOOR

G
Q Q Q Q Q Q Q Q
x L w zW W y zW W y w L x x L w zW W y x w zW W y T
u u W W W W
u u u u W W
u u W W
120

L L L T
x w z y z y w x x w z y x w z y
FC af FG FB ae FB FG FB ae FB FG af FG af FG FB ae FB FG af FG FB ae FB FC

A ELEVATION

F1 F2 F3 F4 F5 F6 F7 F8 F9

PB k PE j PE j PE j PE j PE j PE j PE k PB
CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB CB
Q Q Q Q Q Q Q Q
4800 EAVES

Q Q Q Q Q Q Q Q
q C90 x 1.15BMT r C90 x 1.15BMT r C90 x 1.15BMT r C90 x 1.15BMT r C90 x 1.15BMT r C90 x 1.15BMT r C90 x 1.15BMT r C90 x 1.15BMT q
4800

Q
STUD FRAMING Q
STUD FRAMING Q
STUD FRAMING Q
STUD FRAMING Q
STUD FRAMING Q
STUD FRAMING Q
STUD FRAMING Q
STUD FRAMING

Q Q Q Q Q Q Q Q

s
FC FG

B ELEVATION

STRUCTURAL STEEL MEMBERS:

PROTECTIVE COATINGS FOR STRUCTURAL STEELWORK TO BE IN
ACCORDANCE WITH NCC REQUIREMENTS AND AS 2312

STEEL WORK NOTES:

AND AS 4055
ALL STEEL WORK TO COMPLY WITH NASH STANDARDS AND AUSTRALIAN STANDARDS:
- AS 4100, AS 4600, AS 3623, AS 1554, AS 3678, AS 3679 AND/OR AS 1163.

ALL STEEL COMPONENTS TO BE FULLY GALVANISED 5.0m

ALL CONSTRUCTION WITHIN 1.5KM OF THE COAST OR 100M OF THE RIVER IS TO HAVE
MARINE GRADE ROOF SHEETING, FLASHING, FIXINGS AND STEEL FINISH TO MEET THE
MANUFACTURER'S RECOMMENDATIONS FOR MARINE EXPOSURE TOTAL SPAN
REFER TO SHEET S-01 FOR FULL STEEL WORK NOTES
ALL STEEL MEMBERS SHALL BE INSTALLED IN ACCORDANCE WITH
TOTAL SPAN SPECIFICATIONS
* IMPORTANT: NO CEILING OR INTERNAL WALL LINING SHOULD BE ADDED TO THE SHED STRUCTURE
OTHER THAT WET AREA AND FIRE WALL ALONG BOUNDARY

* ALL CAPPINGS, GUTTER, DOWNPIPE, DRIP RAILS, FLASHING, POP-INS & CLIPS FITTED TO BUILDER'S DETAIL

NOTES:
1. ALL WORK TO BE COMPLETED IN ACCORDANCE TO NATIONAL CONSTRUCTION CODE (NCC) AND AUSTRALIAN STANDARDS BY A FULLY
LICENCED / REGISTERED BUILDER.
2. IT IS THE BUILDER'S RESPONSIBILITY TO COMPLY WITH ALL STATUTORY AUTHORITY REGULATIONS AND REQUIREMENTS WHICH IN THE EVENT
OF ANY DISCREPANCY SHALL TAKE PRECEDENCE OVER THESE DRAWINGS
3. BUILDER MUST CONFIRM ON SITE ALL DIMENSIONS IN ACCORDANCE WITH THESE PLANS . DO NOT SCALE FROM DRAWINGS.
4. ENSURE NO EXISTING STRUCTURES OR SERVICES ON THIS OR ADJACENT PROPERTIES WILL BE SURCHARGED OR UNDERMINED BY THESE
WORKS. IF UNSURE, CONTACT THE STRUCTURAL ENGINEER FOR PROPER ADVICE PRIOR TO PROCEEDING.
5. DOWNPIPES TYPE, SIZE AND LOCATION TO BE DETERMINED ON SITE BY BUILDER.
6. ANY DISCREPANCIES TO BE NOTIFED TO THE OWNER OR STRUCTURAL ENGINEER PRIOR TO WORK COMMENCING.
7. DRAINAGE REQUIREMENTS (SUBSOIL, SOAKWELLS, RUNOFF AND STORMWATER) ARE TO BE DETERMINED ON SITE. ENSURE THERE IS NO
DISCHARGE OR POOLING OF WATER AGAINST THE SLAB AND / OR FOOTINGS. *THIS DRAWING IS STRICTLY TO BE USED ONLY FOR COUNCIL APPROVAL APPLICATION

DATE PROJECT DRAWING TITLE DWG NO. NOTES

1. All architectural dimensions are in millimeters unless notified otherwise.

12/07/2022
PROPOSED SHEDS ON LOT 264, #9 SHED 1 STEEL LAYOUT PLAN 2. All dimensions are to be checked on site.
SHEET SIZE COX STREET, PINJARRA WA - 02

SCALE 1 : 150 A3
A005 3. Drawing is strictly to be used for council application purpose only and does not form part of construction working
drawings. Property owner holds / bears the full responsibilities & liabilities for supervision & coordination to all construction
works & details after receiving building permit approval from local council.
 A1 B1 B1 A1

RIDGE RIDGE
L 15° F 15° F
AL ALL AL L ALL
15° F 15° F

EAVE EAVE
E4 E3 E2 E1
15000

6408

6408
0.4BMT 6-RIB WALL CLADDING FITTED IN ACCORDANCE 0.4BMT 6-RIB WALL CLADDING FITTED IN ACCORDANCE

4800

4800
TO MANUFACTURER'S SPECIFICATION TO MANUFACTURER'S SPECIFICATION
5000 5000 5000

B1

E1 ELEVATION E4 ELEVATION
3 2 1

E4 E3 E2 E1 E1 E2 E3 E4
12000

0.4BMT 6-RIB ROOF SHEET @15° FALL. FITTED IN 0.4BMT 6-RIB ROOF SHEET @15° FALL. FITTED IN
5.0m 5.0m 5.0m ACCORDANCE TO MANUFACTURER'S SPECIFICATION ACCORDANCE TO MANUFACTURER'S SPECIFICATION

0.4BMT 6-RIB WALL CLADDING FITTED IN ACCORDANCE

TO MANUFACTURER'S SPECIFICATION

0.4BMT 6-RIB WALL CLADDING FITTED IN ACCORDANCE

TO MANUFACTURER'S SPECIFICATION

3200
A1 ROLLER DOOR

1940
D
E4 E1
C C ELEVATION D ELEVATION

STEEL WORK NOTES:

ALL STEEL WORK TO COMPLY WITH NASH STANDARDS AND AUSTRALIAN STANDARDS:
- AS 4100, AS 4600, AS 3623, AS 1554, AS 3678, AS 3679 AND/OR AS 1163.

ALL STEEL COMPONENTS TO BE FULLY GALVANISED

ALL CONSTRUCTION WITHIN 1.5KM OF THE COAST OR 100M OF THE RIVER IS TO HAVE
MARINE GRADE ROOF SHEETING, FLASHING, FIXINGS AND STEEL FINISH TO MEET THE
MANUFACTURER'S RECOMMENDATIONS FOR MARINE EXPOSURE

REFER TO SHEET S-01 FOR FULL STEEL WORK NOTES

* IMPORTANT: NO CEILING OR INTERNAL WALL LINING SHOULD BE ADDED TO THE SHED STRUCTURE
OTHER THAT WET AREA AND FIRE WALL ALONG BOUNDARY

* ALL CAPPINGS, GUTTER, DOWNPIPE, DRIP RAILS, FLASHING, POP-INS & CLIPS FITTED TO BUILDER'S DETAIL

NOTES:
1. ALL WORK TO BE COMPLETED IN ACCORDANCE TO NATIONAL CONSTRUCTION CODE (NCC) AND AUSTRALIAN STANDARDS BY A FULLY
LICENCED / REGISTERED BUILDER.
2. IT IS THE BUILDER'S RESPONSIBILITY TO COMPLY WITH ALL STATUTORY AUTHORITY REGULATIONS AND REQUIREMENTS WHICH IN THE EVENT
OF ANY DISCREPANCY SHALL TAKE PRECEDENCE OVER THESE DRAWINGS
3. BUILDER MUST CONFIRM ON SITE ALL DIMENSIONS IN ACCORDANCE WITH THESE PLANS . DO NOT SCALE FROM DRAWINGS.
4. ENSURE NO EXISTING STRUCTURES OR SERVICES ON THIS OR ADJACENT PROPERTIES WILL BE SURCHARGED OR UNDERMINED BY THESE
WORKS. IF UNSURE, CONTACT THE STRUCTURAL ENGINEER FOR PROPER ADVICE PRIOR TO PROCEEDING.
5. DOWNPIPES TYPE, SIZE AND LOCATION TO BE DETERMINED ON SITE BY BUILDER.
6. ANY DISCREPANCIES TO BE NOTIFED TO THE OWNER OR STRUCTURAL ENGINEER PRIOR TO WORK COMMENCING.
7. DRAINAGE REQUIREMENTS (SUBSOIL, SOAKWELLS, RUNOFF AND STORMWATER) ARE TO BE DETERMINED ON SITE. ENSURE THERE IS NO
DISCHARGE OR POOLING OF WATER AGAINST THE SLAB AND / OR FOOTINGS. *THIS DRAWING IS STRICTLY TO BE USED ONLY FOR COUNCIL APPROVAL APPLICATION

DATE PROJECT DRAWING TITLE DWG NO. NOTES

1. All architectural dimensions are in millimeters unless notified otherwise.

12/07/2022

N
PROPOSED SHEDS ON LOT 264, #9 SHED 2 LAYOUT PLAN 2. All dimensions are to be checked on site.
SHEET SIZE COX STREET, PINJARRA WA

SCALE 1 : 150 A3
A006 3. Drawing is strictly to be used for council application purpose only and does not form part of construction working
drawings. Property owner holds / bears the full responsibilities & liabilities for supervision & coordination to all construction
works & details after receiving building permit approval from local council.
 A1 B1 B1 A1

E4 E3 E2 E1 PN PN PN PN
UH UH
f f f f

1608

1608
PB W
ai N T ai W PB PB W
ai N T ai W PB

448

448
W F
ai F N T F
ai F W W F
ai F N T F
ai F W

EQ

EQ
al Q Q
al al Q Q
al al Q Q
al al Q Q
al
f k e j e k f W
ai N T
ai W W
ai N T
ai W
B1

EQ

EQ
CB CB

4800

4800
CB CB CB CB
l l l l l

4032

4032
W N T W W N T W
i c i
T
F
ai F F
ai F F
ai F F
ai F
F F F F F F q q q q q q

EQ

EQ
mQ m mQ mQ m T
al Q Q
al al Q Q
al al Q Q
al al Q Q
al
Q Q Q
i c i W
ai N T
ai W W
ai N T
ai W

EQ

EQ
T
F i F F c F F i F
W
ai N T
ai W W
ai N T
ai W
mQ m mQ mQ m FC FC FC FC FC FC

120

120
Q Q Q T
i c i
F i F F c F F i F
T E1 ELEVATION E4 ELEVATION
mQ Q
m mQ Q
mQ Q
m T
i c i
PN T g T PR g T PR g T PN
PN L g T PR g T PR g L PN

Q h Q Q h Q Q h Q T
m F F
m m F F
m F F
m
h h h T
E4 E3 E2 E1 E1 E2 E3 E4
Q
h Q Q
h Q Q
h Q T
m F F
m m F F
m F F
m
h h h T

Q h Q Q h Q Q h Q T PB k PE j PE k PB PB k PE j PE k PB
m F F
m m F F
m F F
m CB CB CB CB CB CB CB CB CB CB CB CB
h h h T s s s s s s
T F F F F F F T T F F F F F T
CB CB CB CB CB CB ad ad ad ad ad ad ac ad ad ad ad
A1 Q
s
Q Q
s
Q Q
s
Q
yW ab
Q
z
Q
s
Q Q
s
Q

4800 EAVES
f k e j e k f q T
r r T
q T W
r r T
q
q
s s s yW z s s

OP
F F F F F F T aa F F F

EN
T T W OE T
ad ad ad ad ad ad v v ad ad ad

IN
D

G
Q Q Q Q Q Q Q Q Q
T
s s s T T yW W
z w s s T
E4 E1 T T
u u T
s s s T yW W
z w s s
FC FG FG FC FC FB ae FB FG af FG FC

STRUCTURAL STEEL MEMBERS:

C
PROTECTIVE COATINGS FOR STRUCTURAL STEELWORK TO BE IN
ACCORDANCE WITH NCC REQUIREMENTS AND AS 2312 C ELEVATION D ELEVATION

STEEL WORK NOTES:

ALL STEEL WORK TO COMPLY WITH NASH STANDARDS AND AUSTRALIAN STANDARDS:
- AS 4100, AS 4600, AS 3623, AS 1554, AS 3678, AS 3679 AND/OR AS 1163.
AND AS 4055
ALL STEEL COMPONENTS TO BE FULLY GALVANISED

ALL CONSTRUCTION WITHIN 1.5KM OF THE COAST OR 100M OF THE RIVER IS TO HAVE
MARINE GRADE ROOF SHEETING, FLASHING, FIXINGS AND STEEL FINISH TO MEET THE
MANUFACTURER'S RECOMMENDATIONS FOR MARINE EXPOSURE 5.0m
REFER TO SHEET S-01 FOR FULL STEEL WORK NOTES

TOTAL SPAN
* IMPORTANT: NO CEILING OR INTERNAL WALL LINING SHOULD BE ADDED TO THE SHED STRUCTURE
OTHER THAT WET AREA AND FIRE WALL ALONG BOUNDARY ALL STEEL MEMBERS SHALL BE INSTALLED IN ACCORDANCE WITH
TOTAL SPAN SPECIFICATIONS
* ALL CAPPINGS, GUTTER, DOWNPIPE, DRIP RAILS, FLASHING, POP-INS & CLIPS FITTED TO BUILDER'S DETAIL

NOTES:
1. ALL WORK TO BE COMPLETED IN ACCORDANCE TO NATIONAL CONSTRUCTION CODE (NCC) AND AUSTRALIAN STANDARDS BY A FULLY
LICENCED / REGISTERED BUILDER.
2. IT IS THE BUILDER'S RESPONSIBILITY TO COMPLY WITH ALL STATUTORY AUTHORITY REGULATIONS AND REQUIREMENTS WHICH IN THE EVENT
OF ANY DISCREPANCY SHALL TAKE PRECEDENCE OVER THESE DRAWINGS
3. BUILDER MUST CONFIRM ON SITE ALL DIMENSIONS IN ACCORDANCE WITH THESE PLANS . DO NOT SCALE FROM DRAWINGS.
4. ENSURE NO EXISTING STRUCTURES OR SERVICES ON THIS OR ADJACENT PROPERTIES WILL BE SURCHARGED OR UNDERMINED BY THESE
WORKS. IF UNSURE, CONTACT THE STRUCTURAL ENGINEER FOR PROPER ADVICE PRIOR TO PROCEEDING.
5. DOWNPIPES TYPE, SIZE AND LOCATION TO BE DETERMINED ON SITE BY BUILDER.
6. ANY DISCREPANCIES TO BE NOTIFED TO THE OWNER OR STRUCTURAL ENGINEER PRIOR TO WORK COMMENCING.
7. DRAINAGE REQUIREMENTS (SUBSOIL, SOAKWELLS, RUNOFF AND STORMWATER) ARE TO BE DETERMINED ON SITE. ENSURE THERE IS NO
DISCHARGE OR POOLING OF WATER AGAINST THE SLAB AND / OR FOOTINGS. *THIS DRAWING IS STRICTLY TO BE USED ONLY FOR COUNCIL APPROVAL APPLICATION

DATE PROJECT DRAWING TITLE DWG NO. NOTES

1. All architectural dimensions are in millimeters unless notified otherwise.

12/07/2022

N
PROPOSED SHEDS ON LOT 264, #9 SHED 2 STEEL LAYOUT PLAN 2. All dimensions are to be checked on site.
SHEET SIZE COX STREET, PINJARRA WA

SCALE 1 : 150 A3
A007 3. Drawing is strictly to be used for council application purpose only and does not form part of construction working
drawings. Property owner holds / bears the full responsibilities & liabilities for supervision & coordination to all construction
works & details after receiving building permit approval from local council.
 48000

400 47200 400

q r r r r r r r q

400
ET1

* COMPACTED FILL UNDER SLAB AND FOOTINGS.

10200

11000
q IN 500mm WELL WATERED LAYERS. TO GIVE q
S1 STANDARD PERTH OF 8 BLOWS PER 300mm
ET1

ET1
2-N16 BARS x 2000 LONG
TIED UNDER MESH

1000 2500 1000

2-N16 BARS x 2000 LONG 2-N16 BARS x 2000 LONG 2-N16 BARS x 2000 LONG 2-N16 BARS x 2000 LONG
TIED UNDER MESH TIED UNDER MESH TIED UNDER MESH TIED UNDER MESH

IT1

IT1

IT1
IT1

IT1
1500

1500

1500
ET1

400
q r r r r r r r q

SLAB AND FOOTING LAYOUT PLAN - SHED 1

1 1 : 150

15000
WET AREA SETDOWN
WET AREA SETDOWN TO MAINTAIN 125mm SLAB THICKNESS. FOLD MESH DOWN TO MAINTAIN COVER.
PLACE DIAGONAL BARS AT RE-ENTRANT CORNERS FOR STEPS OVER 30mm.
400 14200 400
- WATERPROOFING TO WET AREAS IN ACCORDANCE TO AS3740 & NCC REQUIREMENTS. B250 x 85 PORTAL LEG. REFER SCHEDULE
0.4BMT 6-RIB WALL CLADDING
- ALL PLUMBING FIXTURES & PENETRATIONS TO BE DETERMINED ON SITE BY BUILDER / FITTED IN ACCORDANCE TO
q r r q 220 x 10mm THICK GALV. STEEL ANGLE
PLUMBER. ALL PENETRATIONS TO BE FULLY WATERPROOF SEALED. MANUFACTURER'S SPECIFICATION

400
BASE BRACKET. REFER DRAWING A010
FOR TYPICAL CONNECTION DETAIL
- FLOOR WASTE LOCATION TO BE DETERMINED ON SITE BY BUILDER / PLUMBER
C150 x 64 WALL GIRTS. REFER SCHEDULE
ET1 32MPa CONCRETE
- PROVIDE 2-N16 BARS x 2000 LONG CENTRAL IN SLAB AT ALL RE-ENTRANT CORNERS.
PARGE EXPOSED SLAB
'S1' GROUND SLAB. REFER SCHEDULE
- PLACE MESH ON APPROVED SUPPORT CHAIRS PRIOR TO CONCRETE PLACEMENT.

30

MIN.
100

200 MIN.
125
- INDICATES 40mm SLAB SET DOWN IN WET AREA. MAINTAIN 125mm THICK * COMPACTED FILL UNDER SLAB AND FOOTINGS.
SLAB. FOLD MESH DOWN TO MAINTAIN COVER. IN 500mm WELL WATERED LAYERS. TO GIVE
STANDARD PERTH OF 8 BLOWS PER 300mm

500
50 x 50mm FILLET SF1

MAXIMUM IMPOSED LOAD FOR THE SLAB TO BE 4.5 kN/m²

12000

11200

70 COVER
0.2mm POLYTHENE MEMBRANE ON
q S1 q COMPACTED SAND
ET1

ET1
SLAB AND FOOTING SHEDULE
3 L11 TM, 70 BOTTOM COVER COMPACTED FILL ANCHOR BOLTS EMBEDMENT
S1: 125mm THICK CONCRETE FLOOR SLAB, SL92 REINFORCEMENT, 30 TOP COVER, 425 LAP 400
SF1: 400 x 500mm DEEP CONCRETE STRIP FOOTING, 3 L11-TM, 70 BOTTOM COVER
IT1: 300 x 165mm DEEP CONCRETE INTERNAL THICKENING, SL92 MESH

* THESE DIMENSIONS ARE PROVIDED AS A GUIDE ONLY. IT IS THE RESPONSIBILITY OF THE 'SF1' DETAIL - TYPICAL
CONCRETER TO CONFIRM THAT ALL DIMENSIONS ARE CORRECT. 3 1 : 20
ET1
400

GENERAL NOTES:
- ALL CONCRETE TO BE IN ACCORDANCE WITH AS 3600. MINIMUM CONCRETE STRENGTH TO BE 32MPa. q r r q
MASS CONCRETE TO BE N20/20/80.
- SAND PAD IS REQUIRED UNDER THE SLAB AND FOOTING.
- SAND UNDER THE SLAB TO BE COMPACTED TO MINIMUM 7 BLOWS PER 300mm USING PERTH SAND
PENETROMETER (PSP). SLAB AND FOOTING LAYOUT PLAN - SHED 2
- SOIL FILL TO BE CONTROLLED FILL IN ACCORDANCE WITH CLAUSE 6.4.2. AS2870 2 1 : 150
- PROVIDE THE CONCRETE SLAB WITH WATER PROOF MEMBRANE IN ACCORDANCE WITH AS2870. *THIS DRAWING IS STRICTLY TO BE USED ONLY FOR COUNCIL APPROVAL APPLICATION

DATE PROJECT DRAWING TITLE DWG NO. NOTES

1. All architectural dimensions are in millimeters unless notified otherwise.

12/07/2022

N
PROPOSED SHEDS ON LOT 264, #9 SLAB AND FOOTING LAYOUT 2. All dimensions are to be checked on site.
SHEET SIZE COX STREET, PINJARRA WA PLANS

SCALE As indicated A3
A008 3. Drawing is strictly to be used for council application purpose only and does not form part of construction working
drawings. Property owner holds / bears the full responsibilities & liabilities for supervision & coordination to all construction
works & details after receiving building permit approval from local council.
 5.0 PL (G450) APEX PLATE. 12x M16
8.8 GRADE FLANGED BOLTS
STRUCTURAL ASSEMBLY 'd' RIDGE PURLIN

'e' PORTAL RAFTER - MID

'c' INNER PURLIN T PR T

5.0 PL (G450) KNEE PLATE 5.0 PL (G450) KNEE PLATE

1474
16x M16 8.8 GRADE 16x M16 8.8 GRADE
* FIRE WALL TO BE FIRECRUNCH FCA K-CLAD FLANGED BOLTS FLANGED BOLTS
SYSTEM TO ACHIEVE FRL 60/60/60 ALONG BOUNDARY STRUCTURAL ASSEMBLY STRUCTURAL ASSEMBLY
WALL. REFER TO MANUFACTURER'S INSTALLATION
MANUAL FOR SPECIFICATION AND FIXING DETAILS
'j/k' GUTTER PURLIN 'j/k' GUTTER PURLIN
CB CB
PE PE
FIRECRUNCH WALL LINING TO WRAP
FIRECRUNCH FCA K-CLAD SE10mm EXTERNAL
AROUND PORTAL LEGS
WALL CLADDING SHEET WITH VAPOUR
BARRIER. FITTED IN ACCORDANCE WITH
MANUFACTURER'S SPECIFICATION
T
C90 x 1.15BMT STEEL STUD SPACED C150 x 64 SIDE GIRT
FIRECRUNCH FCA K-CLAD TE10mm INTERNAL
WALL LINING. RECESSED EDGE BOARD FOR @ 400mm C/C MAX. NOGGING
SPACED @ 1200mm C/C MAX. C90 x 1.15BMT STEEL STUD SPACED @ 400mm C/C
PLASTER SET JONTS. FITTED IN ACCORDANCE MAX. NOGGING SPACED @ 1200mm C/C MAX.

4800
WITH MANUFACTURER'S SPECIFICATION
SCREW FIX RIGHT ANGLE BRACKET, 1.5BMT GAUGE OR USE
SOUDAL T-REX INSTANT PERMANENT FIXING OR SIMLAR
32MPa CONCRETE PRODUCTS . [Link]
'r' PORTAL LEG - MID 'r' PORTAL LEG - MID

SEAL ALL GAPS WITH AS1530.4 PU FIRE SEALANT. INSTALL

'S1' GROUND SLAB. REFER SCHEDULE
SUITABLE DAMP PROOF COURSE BARRIER TO BCA STANDARD
75 MIN.
30

MIN.
100
125

500

50 x 50mm FILLET SF1

FG FG
TYPICAL MID PORTAL FRAME - SHED 1
70 COVER

0.2mm POLYTHENE MEMBRANE ON

COMPACTED SAND

3 L11 TM, 70 BOTTOM COVER COMPACTED FILL

FIX BOTTOM STUD TO CONCRETE BASE VIA M16
400 CHEMICAL ANCHOR BOLT SPACED @ 900 C/C
MAX. MIN. 175mm EMBEDMENT INTO CONCRETE
5.0 PL (G450) APEX PLATE. 12x M16 5.0 PL (G550) APEX PLATE. 12x M16
BASE, 50mm COVER FROM CONCRETE EDGE
8.8 GRADE FLANGED BOLTS 8.8 GRADE FLANGED BOLTS
STRUCTURAL ASSEMBLY STRUCTURAL ASSEMBLY

'e' PORTAL RAFTER - MID 'e' PORTAL RAFTER - MID

BOUNDARY FIRE WALL (FRL 60/60/60) DETAIL
2 1 : 20 'c' INNER PURLIN T PR T 'c' INNER PURLIN

1608
5.0 PL (G450) KNEE PLATE 5.0 PL (G450) KNEE PLATE
16x M16 8.8 GRADE 16x M16 8.8 GRADE
FLANGED BOLTS FLANGED BOLTS
STRUCTURAL ASSEMBLY STRUCTURAL ASSEMBLY

STRUCTURAL STEEL MEMBERS:

PROTECTIVE COATINGS FOR STRUCTURAL STEELWORK TO BE IN 'j/k' GUTTER PURLIN 'j/k' GUTTER PURLIN
CB CB
PE PE
ACCORDANCE WITH NCC REQUIREMENTS AND AS 2312

STEEL WORK NOTES:

ALL STEEL WORK TO COMPLY WITH NASH STANDARDS AND AUSTRALIAN STANDARDS:
- AS 4100, AS 4600, AS 3623, AS 1554, AS 3678, AS 3679 AND/OR AS 1163.
T T
ALL STEEL COMPONENTS TO BE FULLY GALVANISED C150 x 64 SIDE GIRT C150 x 64 SIDE GIRT

ALL CONSTRUCTION WITHIN 1.5KM OF THE COAST OR 100M OF THE RIVER IS TO HAVE
4800

MARINE GRADE ROOF SHEETING, FLASHING, FIXINGS AND STEEL FINISH TO MEET THE
MANUFACTURER'S RECOMMENDATIONS FOR MARINE EXPOSURE

REFER TO SHEET S-01 FOR FULL STEEL WORK NOTES

'r' PORTAL LEG - MID 'r' PORTAL LEG - MID

* IMPORTANT: NO CEILING OR INTERNAL WALL LINING SHOULD BE ADDED TO THE SHED STRUCTURE
OTHER THAT WET AREA AND FIRE WALL ALONG BOUNDARY

* ALL CAPPINGS, GUTTER, DOWNPIPE, DRIP RAILS, FLASHING, POP-INS & CLIPS FITTED TO BUILDER'S DETAIL

NOTES: FG FG
1. ALL WORK TO BE COMPLETED IN ACCORDANCE TO NATIONAL CONSTRUCTION CODE (NCC) AND AUSTRALIAN STANDARDS BY A FULLY TYPICAL MID PORTAL FRAME - SHED 2
LICENCED / REGISTERED BUILDER.
2. IT IS THE BUILDER'S RESPONSIBILITY TO COMPLY WITH ALL STATUTORY AUTHORITY REGULATIONS AND REQUIREMENTS WHICH IN THE EVENT
OF ANY DISCREPANCY SHALL TAKE PRECEDENCE OVER THESE DRAWINGS
3. BUILDER MUST CONFIRM ON SITE ALL DIMENSIONS IN ACCORDANCE WITH THESE PLANS . DO NOT SCALE FROM DRAWINGS.
4. ENSURE NO EXISTING STRUCTURES OR SERVICES ON THIS OR ADJACENT PROPERTIES WILL BE SURCHARGED OR UNDERMINED BY THESE
WORKS. IF UNSURE, CONTACT THE STRUCTURAL ENGINEER FOR PROPER ADVICE PRIOR TO PROCEEDING.
5. DOWNPIPES TYPE, SIZE AND LOCATION TO BE DETERMINED ON SITE BY BUILDER.
6. ANY DISCREPANCIES TO BE NOTIFED TO THE OWNER OR STRUCTURAL ENGINEER PRIOR TO WORK COMMENCING. TYPICAL PORTAL FRAMES
7. DRAINAGE REQUIREMENTS (SUBSOIL, SOAKWELLS, RUNOFF AND STORMWATER) ARE TO BE DETERMINED ON SITE. ENSURE THERE IS NO
DISCHARGE OR POOLING OF WATER AGAINST THE SLAB AND / OR FOOTINGS.
1 1 : 75 *THIS DRAWING IS STRICTLY TO BE USED ONLY FOR COUNCIL APPROVAL APPLICATION

DATE PROJECT DRAWING TITLE DWG NO. NOTES

1. All architectural dimensions are in millimeters unless notified otherwise.

12/07/2022
PROPOSED SHEDS ON LOT 264, #9 TYPICAL PORTAL FRAME, 2. All dimensions are to be checked on site.
SHEET SIZE COX STREET, PINJARRA WA FIRE WALL DETAIL

SCALE As indicated A3
A009 3. Drawing is strictly to be used for council application purpose only and does not form part of construction working
drawings. Property owner holds / bears the full responsibilities & liabilities for supervision & coordination to all construction
works & details after receiving building permit approval from local council.
 16 x 200 L-BOLT 16 x 200 L-BOLT

16

16
16 x 200 L-BOLT

* THESE DETAILS ARE COPYRIGHT MATERIALS OF SPANBUILD NEW ZEALAND LIMITED, AND IS PROVIDED BY THE CLIENT OF THIS PROJECT TO BE INCLUDED FOR THE PURPOSE OF COUNCIL APPROVAL APPLICATION. BUILDING
DESIGNER HAS NO INTENTION TO REPRODUCE THE DETAILS OUTSIDE OF THIS SPECIFIC PROJECT AND ACCEPTS NO LIABILITY FOR ANY INFRINGEMENT OF COPYRIGHTED MATERIALS.
DATE PROJECT DRAWING TITLE DWG NO. NOTES

1. All architectural dimensions are in millimeters unless notified otherwise.

12/07/2022
PROPOSED SHEDS ON LOT 264, #9 TYPICAL DETAILS 2. All dimensions are to be checked on site.
SHEET SIZE COX STREET, PINJARRA WA

SCALE A3
A010 3. Drawing is strictly to be used for council application purpose only and does not form part of construction working
drawings. Property owner holds / bears the full responsibilities & liabilities for supervision & coordination to all construction
works & details after receiving building permit approval from local council.
* THESE DETAILS ARE COPYRIGHT MATERIALS OF SPANBUILD NEW ZEALAND LIMITED, AND IS PROVIDED BY THE CLIENT OF THIS PROJECT TO BE INCLUDED FOR THE PURPOSE OF COUNCIL APPROVAL APPLICATION. BUILDING
DESIGNER HAS NO INTENTION TO REPRODUCE THE DETAILS OUTSIDE OF THIS SPECIFIC PROJECT AND ACCEPTS NO LIABILITY FOR ANY INFRINGEMENT OF COPYRIGHTED MATERIALS.
DATE PROJECT DRAWING TITLE DWG NO. NOTES

1. All architectural dimensions are in millimeters unless notified otherwise.

12/07/2022
PROPOSED SHEDS ON LOT 264, #9 TYPICAL DETAILS 2. All dimensions are to be checked on site.
SHEET SIZE COX STREET, PINJARRA WA

SCALE A3
A011 3. Drawing is strictly to be used for council application purpose only and does not form part of construction working
drawings. Property owner holds / bears the full responsibilities & liabilities for supervision & coordination to all construction
works & details after receiving building permit approval from local council.
 or C90

C80 or C90 to C100, C150, C250 or C300 Section Closed Face

* THESE DETAILS ARE COPYRIGHT MATERIALS OF SPANBUILD NEW ZEALAND LIMITED, AND IS PROVIDED BY THE CLIENT OF THIS PROJECT TO BE INCLUDED FOR THE PURPOSE OF COUNCIL APPROVAL APPLICATION. BUILDING
DESIGNER HAS NO INTENTION TO REPRODUCE THE DETAILS OUTSIDE OF THIS SPECIFIC PROJECT AND ACCEPTS NO LIABILITY FOR ANY INFRINGEMENT OF COPYRIGHTED MATERIALS.
DATE PROJECT DRAWING TITLE DWG NO. NOTES

1. All architectural dimensions are in millimeters unless notified otherwise.

12/07/2022
PROPOSED SHEDS ON LOT 264, #9 TYPICAL DETAILS 2. All dimensions are to be checked on site.
SHEET SIZE COX STREET, PINJARRA WA

SCALE A3
A012 3. Drawing is strictly to be used for council application purpose only and does not form part of construction working
drawings. Property owner holds / bears the full responsibilities & liabilities for supervision & coordination to all construction
works & details after receiving building permit approval from local council.
* THESE DETAILS ARE COPYRIGHT MATERIALS OF SPANBUILD NEW ZEALAND LIMITED, AND IS PROVIDED BY THE CLIENT OF THIS PROJECT TO BE INCLUDED FOR THE PURPOSE OF COUNCIL APPROVAL APPLICATION. BUILDING
DESIGNER HAS NO INTENTION TO REPRODUCE THE DETAILS OUTSIDE OF THIS SPECIFIC PROJECT AND ACCEPTS NO LIABILITY FOR ANY INFRINGEMENT OF COPYRIGHTED MATERIALS.
DATE PROJECT DRAWING TITLE DWG NO. NOTES

1. All architectural dimensions are in millimeters unless notified otherwise.

12/07/2022
PROPOSED SHEDS ON LOT 264, #9 TYPICAL DETAILS 2. All dimensions are to be checked on site.
SHEET SIZE COX STREET, PINJARRA WA

SCALE A3
A014 3. Drawing is strictly to be used for council application purpose only and does not form part of construction working
drawings. Property owner holds / bears the full responsibilities & liabilities for supervision & coordination to all construction
works & details after receiving building permit approval from local council.