Moplen HP648U

Moplen HP648U
High flow with improved transparency and heat stability for TWIM
Features
High flow with broad processing window allows Typical applications
increased design freedom Drinking cups
Excellent transparency and gloss Food containers
Good temperature resistance Thin wall injection products
High stiffness allows downgauging High speed injection molding parts
Good dimensional stability
PP Resin Properties (a) Value ASTM METHOD(b)

Melt flow rate (230°C / 2.16 kg), g/10min 75 D1238
Density, g/cm3 0.90 D792B
Tensile strength at yield, MPa 37 D638
Elongation at yield, % 9 D638
Flexural modulus, MPa 1750 D790A
Notched izod impact strength at 23°C, J/m 26 D256A
Deflection temperature, at 455 kPa, °C 117 D648
(a) Values shown are averages and are not to be considered as specifications.
(b) ASTM test methods are the latest under the Society's current procedures. All molded specimens are prepared by injection molding.
Note: Due to the fact that different regulations in each country set different details of compliance, users of Moplen HP648U are recommended to undertake their
own investigation of the requirements and comply with each regulation set forth, for instance, in applicable local F&DA requirements. Ultimately the users must
make their own determination that their use of Moplen HP648U is safe, lawful and technically suitable in their intended applications. Unless specifically indicated,
the grades mentioned are not suitable for applications in the pharmaceutical/medical sector.
This product(s) may not be used in the manufacture of any of the following, without prior written approval by Seller for each specific product and application:
(i) U.S. FDA Class I or II Medical Devices; Health Canada Class I, II or III Medical Devices; European Union Class I or II Medical Devices;
(ii) film, overwrap and/or product packaging that is considered a part or component of one of the aforementioned medical devices;
(iii) packaging in direct contact with a pharmaceutical active ingredient and/or dosage form that is intended for inhalation, injection, intravenous, nasal, ophthalmic
(eye), digestive, or topical (skin) administration;
(iv) tobacco related products and applications, electronic cigarettes and similar devices.
(v) safety components in automotive applications, for example: air bags, air bag unit housings and covers, seat belt mechanisms, brake systems, pedals and pedal
supports, steering systems.
The product(s) may not be used in:
(i) U.S. FDA Class III Medical Devices; Health Canada Class IV Medical Devices; European Class III Medical Devices;
(ii) applications involving permanent implantation into the body;
(iii) life-sustaining medical applications.
All references to U.S. FDA, Health Canada, and European Union regulations include another country's equivalent regulatory classification.
Storage
The resin should be stored in a dry location with good housekeeping practices during storage, transferring and handling. Process enclosures and adequate
ventilation should be used to avoid excessive dust accumulation. Resin should be protected from direct sunlight, temperatures above 40°C and high atmospheric
humidity during storage. Higher storage temperatures may reduce the storage time. The container should be kept closed to prevent contamination. For the
additional recommended storage conditions, please refer to SDS.
Moplen is a trademark of LyondellBasell Industries

HMC Polymers is certified according to ISO 9001 and 14001
Issued 24-Aug-21
The purpose of this document is only for technical support of the use of the product.
Before using a HMC Polymers product, customers and other users should make their own independent determination that the product is suitable for the intended
use. They should also ensure that they can use the HMC Polymers product safely and legally. This document does not constitute a warranty, express or implied,
including a warranty of merchantability or fitness for a particular purpose. In addition, no immunity under HMC Polymers', LyondellBasell's or third parties'
intellectual property rights shall be implied from this document. No one is authorized to make any warranties, issue any immunities or assume any liabilities on
behalf of HMC Polymers except in a writing signed by an authorized HMC Polymers employee. Unless otherwise agreed in writing, the exclusive remedy for all
claims is replacement of the product or refund of the purchase price at HMC Polymers' option, and in no event shall HMC Polymers be liable for special,
consequential, incidental, punitive or exemplary damages.
HMC Polymers Co., Ltd

20/F, Sathorn City Tower, 175 South Sathorn Road,
Thungmahamek, Sathorn, Bangkok 10120, Thailand
Tel +66 2614 3700 Fax +66 2679 6380
www.hmcpolymers.com

Moplen HP648U

Uploaded by

Copyright:

Available Formats

Moplen HP648U

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Moplen HP648U

Uploaded by

Copyright:

Available Formats

Moplen HP648U

PP Resin Properties (a) Value ASTM METHOD(b)

Moplen is a trademark of LyondellBasell Industries

HMC Polymers Co., Ltd

You might also like